Due to the increase in the number of power tables for 6Ghz on CLC,
the variable nr_country is no longer sufficient to represent the
total quantity. Therefore, we have switched to calculating the
length of clc buf to obtain the correct power table.
Cc: stable@vger.kernel.org
Fixes: c948b5da6b ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250116062131.3860198-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Assuming sums of values stored in variables such as sub_total_cnt
and total_ppdu_cnt are big enough to warrant their u64 type, it
makes sense to ensure that their calculation takes into account
possible integer overflow issues.
Play it safe and fix the problem by casting right hand expressions
to u64 as well. Also, slightly adjust tabulation.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 1966a5078f ("mt76: mt7915: add mu-mimo and ofdma debugfs knobs")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://patch.msgid.link/20250114154441.16920-1-n.zhandarovich@fintech.ru
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The mt7925 sometimes fails to enter low power mode during suspend.
This is caused by the chip firmware sending an additional ACK event
to the host after processing the suspend command. Due to timing issues,
this event may not reach the host, causing the chip to get stuck.
To resolve this, the ACK flag in the suspend command is removed,
as it is not needed in the MT7925 architecture. This prevents the
firmware from sending the additional ACK event, ensuring the device
can reliably enter low power mode during suspend.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Link: https://patch.msgid.link/d056938144a3a0336c3a4e3cec6f271899f32bf7.1736775666.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch introduces MLO capability control for the MT792x Wi-Fi driver.
It removes the unused `MT792x_CHIP_CAP_MLO_EVT_EN` flag and introduces new
capability flags `MT792x_CHIP_CAP_MLO_EN` and `MT792x_CHIP_CAP_MLO_EML_EN`
to enable MLO and EML features based on firmware capabilities.
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Reviewed-by: Sabeeh Khan <sabeeh-khan@ti.com>
Link: https://patch.msgid.link/20250217081729.1840930-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/71fbc442aee9a9e892e475f3bbf8f368c6692a55.1738746872.git.namcao@linutronix.de
mt76 does a lot of:
local_bh_disable();
napi_enable(...napi);
napi_schedule(...napi);
local_bh_enable();
local_bh_disable() is not a real lock, its most likely taken
because napi_schedule() requires that we invoke softirqs at
some point. napi_enable() needs to take a mutex, so move it
from under the BH protection.
Fixes: 413f0271f3 ("net: protect NAPI enablement with netdev_lock()")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/dcfd56bc-de32-4b11-9e19-d8bd1543745d@stanley.mountain
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250124031841.1179756-8-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The configuration of mt7992 iBF has some differences to mt7996, rework
related code to make it work.
Also, most of our chipsets support iBF only on HT and VHT mode, except
mt7992 variant that has 5T on 5GHz band also supports iBF on HE and EHT
mode.
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-9-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When stopping AP, mac80211 frees beacon template before it calls
driver's stop_ap operation. In other words, on the path of stopping
AP, ieee80211_beacon_get_template() must returns NULL in
mt7996_mcu_add_beacon(). In such case mt7996 immediately returns
-EINVAL without telling FW to disable the beacon.
This commit refactors mt7996_mcu_add_beacon() so that FW can be
correctly informed when disabling AP interface.
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-8-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The non-AP interfaces would not use conf->vht_ldpc so they never set
STA_CAP_VHT_LDPC even if peer-station support LDPC.
Check conf->vht_ldpc only for AP interface.
Without this patch, station only uses BCC to transmit packet in VHT mode.
Fixes: dda423dd65 ("wifi: mt76: mt7996: remove mt7996_mcu_beacon_check_caps()")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-7-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For mt7992 chipsets, the definition of TXD.DW6.BIT10~15 has different
interpretations on different frame types. Driver only needs to fill
MSDU_CNT for non-management frames.
Fixes: 408566db8c ("wifi: mt76: connac: add new definition of tx descriptor")
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-6-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adjust HE and EHT phy capabilities based on the band constraints.
For 2g band, we shall not enable the capabilities above 40MHz.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-5-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix wrong calculation of the channel times due to incorrect
interpretation from the FW event.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-4-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set HE SU PPDU And HE MU PPDU With 4x HE-LTF And 0.8 us GI within HE PHY
Capabilities element as 1 since hardware can support.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-3-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit includes two changes. First, enable "EHT MU PPDU With 4x
EHT-LTF And 0.8us GI" in EHT Phy capabilities element since hardware
can support. Second, fix the value of "Maximum number of supported
EHT LTFs" in the same element, where the previous setting of 3 in
Bit 3-4 was incorrect.
Fixes: 348533eb96 ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-2-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set max mpdu len to 11454 according to hardware capability.
Without this patch, the max ampdu length would be 3895 and count not get
expected performance.
Fixes: 348533eb96 ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-1-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some countries have strict RF restrictions where changing the regulatory
domain dynamically based on the connected AP is not acceptable.
This patch disables Beacon country IE hinting when a valid country code
is set from usersland (e.g., by system using iw or CRDA).
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Tested-by: David Ruth <druth@chromium.org>
Link: https://patch.msgid.link/20240412085357.13756-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The mt7925e takes a long time to resume in platform resume
scenarios. This is due to the mt7925 reconfiguring the tx
power for each wifi channel during resume. By streamlining
the process and removing redundant power configurations,
the resume time for the mt7925 can be shortened.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Link: https://patch.msgid.link/f075d43d87a5eefa5869baf755e9986edf735860.1735910836.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the system suspend or resume, the WiFi driver sends
an hif_ctrl command to the firmware and waits for an event.
Due to changes in the event format reported by the chip, the
current mt7925's driver does not account for these changes,
resulting in command timeout. Add flow to handle hif_ctrl
event to avoid command timeout. We also exented API
mt76_connac_mcu_set_hif_suspend for connac3 this time.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Link: https://patch.msgid.link/3a0844ff5162142c4a9f3cf7104f75076ddd3b87.1735910562.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When enter suspend/resume while in a connected state, the upper layer
will trigger disconnection before entering suspend, and at the same time,
it will trigger regd_notifier() and update CLC, causing the CLC event to
not be received due to suspend, resulting in a command timeout.
Therefore, the update of CLC is postponed until resume, to ensure data
consistency and avoid the occurrence of command timeout.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Link: https://patch.msgid.link/bab00a2805d0533fd8beaa059222659858a9dcb5.1735910455.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bypass the entry when ofs is equal to dev->reg.map[i].size.
Without this patch, it would get incorrect register mapping when the CR
address is located at the boundary of an entry.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Link: https://patch.msgid.link/OSZPR01MB84344FEFF53004B5CF40BCC198132@OSZPR01MB8434.jpnprd01.prod.outlook.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bypass the entry when ofs is equal to dev->reg.map[i].size.
Without this patch, it would get incorrect register mapping when the CR
address is located at the boundary of an entry.
Fixes: cd4c314a65 ("mt76: mt7915: refine register definition")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Link: https://patch.msgid.link/OSZPR01MB843401EAA1DA6BD7AEF356F298132@OSZPR01MB8434.jpnprd01.prod.outlook.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use generic mt76 chanctx functions and look up phy from vif link.
The driver now uses only a single phy to handle multiple interfaces on
different channels. This is preparation for full MLO support.
Link: https://patch.msgid.link/20250102163508.52945-23-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rework connac helpers related to rate and phymode.
This is a preliminary patch to add MLO support for mt7996 chipsets.
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250102163508.52945-21-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When scanning on a phy/vif combination that does not have an active link,
create a temporary link in order to ensure that we have a valid wcid.
Link: https://patch.msgid.link/20250102163508.52945-11-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds an implementation for the chanctx functions, which can be used
by multi-channel capable drivers. Preparation for adding MLO support.
Link: https://patch.msgid.link/20250102163508.52945-7-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Preparation for supporting multiple radios on a single wiphy on devices
where firmware does not support actual hardware scanning.
This is also a prerequisite for full MLO support
Co-developed-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Co-developed-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250102163508.52945-1-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes linked list management issues during restart, where sta entries
can be recreated and reinitialized while still in the poll list, triggering
kernel warnings.
Link: https://patch.msgid.link/20241230194202.95065-14-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems that the firmware checks the register used for detecting matching
PCIe links in order to figure out if a secondary PCIe link is enabled.
Write the register again just before starting the firmware on hw reset,
in order to fix an issue that left the second band unusable after restart.
Fixes: 9093cfff72 ("mt76: mt7915: add support for using a secondary PCIe link for gen1")
Link: https://patch.msgid.link/20241230194202.95065-11-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When a client is roaming to a different AP interface, a duplicate wtbl entry
can be created. This can lead to lost packets or aggregation issues until
the old entry expires.
In order to fix this issue, delete any conflicting entries from WTBL
whenever a station is authorized.
Link: https://patch.msgid.link/20241230194202.95065-9-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last, which is beneficial
to cultivate a high-quality code.[2]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Zhang Kunbo <zhangkunbo@huawei.com>
Link: https://patch.msgid.link/20241218074552.3271542-1-zhangkunbo@huawei.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add CSA (Channel Switch Announcement) related implementation
in collaboration with mac80211 to deal with dynamic channel
switching.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20241107061440.6545-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To optimize the scan time of mt7925, remove the dwell time
setting for the scan command and let it be controlled by
the firmware as mt7921.
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20241106013221.18101-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In dma init or reset scene, full buffer is needed for all rx rings. Since
this is very time consuming, split the function to perform initial
allocation without holding the spinlock. This avoids causing excessive
scheduler latency.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Reviewed-by: Deren Wu <deren.wu@mediatek.com>
Link: https://patch.msgid.link/57c68a7ce1dd9022fa5e06af2c53d6313f30ec83.1731069062.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Properly retrieve the response for commands with events. Ensure accurate
handling of event-driven commands.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-17-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Clean up MLO settings after disconnection.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-16-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mt7925_mcu_uni_[tx,rx]_ba for MLO support in firmware.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-15-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize secondary link PM state.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-14-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update the power-saving flow for secondary links.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-13-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mt7925_unassign_vif_chanctx to support per-link BSS.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-12-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mt792x_rx_get_wcid to support per-link STA.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-11-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mt7925_mcu_sta_update for broadcast (BC) in the ASSOC state.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-10-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enhance mt7925_mac_link_sta_add to support MLO.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-9-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In mt7925_mac_link_bss_add(), the mt76_connac_mcu_uni_add_dev() function
must be executed only after all parameters have been properly initialized.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-8-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix incorrect parameters for the related channel information command.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-6-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For MLO, each link must have a corresponding WCID.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-3-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For this TLV, the address should be set to the MLD address rather than
the link address.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-2-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit extends the `mt76_connac_mcu_uni_add_dev` function to include
support for Multi-Link Operation (MLO). Additionally, backward
compatibility for MT7921 is preserved, enabling seamless integration with
existing setups.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-1-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
DIV_ROUND_CLOSEST() after kstrtoul() results in an overflow if a large
number such as 18446744073709551615 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.
This commit was inspired by commit: 57ee12b6c5.
Fixes: 02ee68b95d ("mt76: mt7915: add control knobs for thermal throttling")
Signed-off-by: xueqin Luo <luoxueqin@kylinos.cn>
Link: https://patch.msgid.link/20241202031917.23741-3-luoxueqin@kylinos.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
DIV_ROUND_CLOSEST() after kstrtoul() results in an overflow if a large
number such as 18446744073709551615 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.
This commit was inspired by commit: 57ee12b6c5.
Fixes: 6879b2e941 ("wifi: mt76: mt7996: add thermal sensor device support")
Signed-off-by: xueqin Luo <luoxueqin@kylinos.cn>
Link: https://patch.msgid.link/20241202031917.23741-2-luoxueqin@kylinos.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The wrong ieee80211_vif will lead to get invalid ip address and
the correct ieee80211_vif can be obtained from ieee80211_bss_conf.
Fixes: 1473242929 ("wifi: mt76: mt7925: add link handling in the BSS_CHANGED_ARP_FILTER handler")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20241107053005.10558-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use tlv instead of skb, because using skb will get valid data
with wrong offset.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20241104051447.4286-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently, sniffer mode does not support band auto,
so set band_idx to the default 0.
Fixes: 0cb349d742 ("wifi: mt76: mt7925: update mt7925_mac_link_bss_add for MLO")
Signed-off-by: Eric-SY Chang <eric-sy.chang@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20241101074340.26176-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In mt7925_change_vif_links() devm_kzalloc() may return NULL but this
returned value is not checked.
Fixes: 69acd6d910 ("wifi: mt76: mt7925: add mt7925_change_vif_links")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://patch.msgid.link/20241025075554.181572-1-hanchunchao@inspur.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt792x_config_mac_addr_list routine in order to set
the mac address list supported by the driver. Initialize
wiphy->addresses/n_addresses for mt792x driver
Signed-off-by: Hao Zhang <hao.zhang@mediatek.com>
Signed-off-by: Leon Yen <Leon.Yen@mediatek.com>
Signed-off-by: Allan Wang <allan.wang@mediatek.com>
Link: https://patch.msgid.link/20241016101017.19598-1-allan.wang@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Due to a limitation in available memory, the MT7916 firmware can only
handle either 5 GHz or 6 GHz at a time. It does not support runtime
switching without a full restart.
On older firmware, this accidentally worked to some degree due to missing
checks, but couldn't be supported properly, because it left the 6 GHz
channels uncalibrated.
Newer firmware refuses to start on either band if the passed EEPROM
data indicates support for both.
Deal with this limitation by using a module parameter to specify the
preferred band in case both are supported.
Fixes: b4d093e321 ("mt76: mt7915: add 6 GHz support")
Cc: stable@vger.kernel.org
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20241010083816.51880-1-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To avoid incorrect cipher after disconnection, we should
do the key deletion process in this case.
Fixes: e6db67fa87 ("wifi: mt76: ignore key disable commands")
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Tested-by: David Ruth <druth@chromium.org>
Reviewed-by: David Ruth <druth@chromium.org>
Link: https://patch.msgid.link/20240801024335.12981-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When initializing the network card, unplugging the device will
trigger an -EPROTO error, resulting in a flood of error messages
being printed frantically.
The exception is printed as follows：
mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71
mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71
...
It will continue to print more than 2000 times for about 5 minutes,
causing the usb device to be unable to be disconnected. During this
period, the usb port cannot recognize the new device because the old
device has not disconnected.
There may be other operating methods that cause -EPROTO, but -EPROTO is
a low-level hardware error. It is unwise to repeat vendor requests
expecting to read correct data. It is a better choice to treat -EPROTO
and -ENODEV the same way.
Similar to commit 9b0f100c19 ("mt76: usb: process URBs with status
EPROTO properly") do no schedule rx_worker for urb marked with status
set -EPROTO. I also reproduced this situation when plugging and
unplugging the device, and this patch is effective.
Just do not vendor request again for urb marked with status set -EPROTO.
Link: https://lore.kernel.org/all/531681bd-30f5-4a70-a156-bf8754b8e072@intel.com/
Link: https://lore.kernel.org/all/D4B9CC1FFC0CBAC3+20250105040607.154706-1-wangyuli@uniontech.com/
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Co-developed-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://patch.msgid.link/9DD7DE7AAB497CB7+20250113070241.63590-1-wangyuli@uniontech.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In multi-channel scenarios, the granted channel must be aborted before
station remove. Otherwise, the firmware will be put into a wrong state,
resulting in have chance to make subsequence scan no APs.
With this patch, the granted channel will be always aborted before
station remove.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: David Ruth <druth@chromium.org>
Reviewed-by: David Ruth <druth@chromium.org>
Link: https://patch.msgid.link/1ac1ae779db86d4012199a24ea2ca74050ed4af6.1721300411.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
commit c4f0755823 ("wifi: mt76: mt7915: fix command timeout in AP stop
period") changes the behavior of mt7915_bss_info_changed() in mesh mode
when enable_beacon becomes false: it calls mt7915_mcu_add_bss_info(...,
false) and mt7915_mcu_add_sta(..., false) while the previous code
didn't. These sends mcu commands that apparently confuse the firmware.
This breaks scanning while in mesh mode on AsiaRF MT7916 DBDC-based cards:
scanning works but no mesh frames get sent afterwards and the firmware
seems to be hosed. It breaks on MT7916 DBDC but not on MT7915 DBDC.
Fixes: c4f0755823 ("wifi: mt76: mt7915: fix command timeout in AP stop period")
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Link: https://patch.msgid.link/20240927085350.4594-1-nicolas.cavallari@green-communications.fr
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To ensure code clarity and prevent potential errors, it's advisable
to employ the ';' as a statement separator, except when ',' are
intentionally used for specific purposes.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20240911034243.31596-1-shenlichuan@vivo.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This comparison should be >= instead of > to prevent an out of bounds
read and write.
Fixes: 9679ca7326 ("wifi: mt76: mt7925: fix a potential array-index-out-of-bounds issue for clc")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/84bf5dd2-2fe3-4410-a7af-ae841e41082a@stanley.mountain
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The maximum command quota of the firmware may be exceeded because the
command to retrieve the quota setting has not been taken into account.
This patch considers not only the quota usage of the command retrieving
quota settings but also limits the total quota usage.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20240916060157.10157-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Regist the NL80211_IFTYPE_P2P_DEVICE to support p2p device
for mt792x chips
Signed-off-by: Hao Zhang <hao.zhang.mediatek@gmail.com>
Signed-off-by: allan.wang <allan.wang@mediatek.com>
Signed-off-by: Ming Yen Hsieh <MingYen.Hsieh@mediatek.com>
Link: https://patch.msgid.link/20240919081713.23787-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some of the variants do not support background radar, so add a helper
to report background radar capability.
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/20240926032440.15978-3-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support passing customized buffer pointer and length to
mt7996_mcu_get_eeprom().
This is the preparation for adding more variants support which needs to
prefetch FEM module from efuse, and also fixes potential OOB issue when
reading the last efuse block.
Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/20240926032440.15978-1-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Setting beacon_int_min_gcd and NL80211_IFTYPE_ADHOC in the same interface
combination is invalid, which will trigger the following warning trace
and get error returned from wiphy_register().
[ 10.080325] Call trace:
[ 10.082761] wiphy_register+0xc4/0x76c [cfg80211]
[ 10.087465] ieee80211_register_hw+0x800/0xac4 [mac80211]
[ 10.092868] mt76_register_device+0x16c/0x2c0 [mt76]
[ 10.097829] mt7996_register_device+0x740/0x844 [mt7996e]
Fix this by removing unused adhoc iftype.
Fixes: 948f652498 ("wifi: mt76: mt7996: advertize beacon_int_min_gcd")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241007135133.5336-1-shayne.chen@mediatek.com
ML interfaces can have multiple affiliated links to it and
hence there is a need to report tx power of specified link
rather deflink.
Add changes to report tx power of requested link from mac80211,
also pass link id as an argument in get_tx_power op so that supported
drivers can use it to report link's tx power.
Co-developed-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://patch.msgid.link/20241125083217.216095-3-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most likely the last -next pull request for v6.13. Most changes are in
Realtek and Qualcomm drivers, otherwise not really anything
noteworthy.
Major changes:
mac80211
* EHT 1024 aggregation size for transmissions
ath12k
* switch to using wiphy_lock() and remove ar->conf_mutex
* firmware coredump collection support
* add debugfs support for a multitude of statistics
ath11k
* dt: document WCN6855 hardware inputs
ath9k
* remove include/linux/ath9k_platform.h
ath5k
* Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
rtw88:
* 8821au and 8812au USB adapters support
rtw89
* thermal protection
* firmware secure boot for WiFi 6 chip
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmc04UYRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuckgf/RV0zy8gMuzJ/cSk1GDKoOYmEwAZ4JvtW
teAKghsODDW/bng2iKnXphJyx3spZRCNuvOmfPcHsWoResX+vqrKJOaER/3159OF
68xAPZNXPRF4M693IpIUB/P3uTw/jieXPI7ftSPuUOhStca/ALwQd5Lp3kNKkVtq
HipXJwCenVS7Hd8DdHbpvYFUckRWr3tHPFlOgG3qOQOVvfRen2z9rhM14oK9rn+h
f309ATHKTbpTKNagOPYAYcyHs3zE59hlVRgRqHL7Ew0a0HI8uPJ4KK2n5W6tZJFN
swhoQolc1uXrRYlZ3Bdr7mKSIqt557kRz7NJ9ITe7KKCU0CxM/7nhQ==
=v8bS
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.13
Most likely the last -next pull request for v6.13. Most changes are in
Realtek and Qualcomm drivers, otherwise not really anything
noteworthy.
Major changes:
mac80211
* EHT 1024 aggregation size for transmissions
ath12k
* switch to using wiphy_lock() and remove ar->conf_mutex
* firmware coredump collection support
* add debugfs support for a multitude of statistics
ath11k
* dt: document WCN6855 hardware inputs
ath9k
* remove include/linux/ath9k_platform.h
ath5k
* Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
rtw88:
* 8821au and 8812au USB adapters support
rtw89
* thermal protection
* firmware secure boot for WiFi 6 chip
* tag 'wireless-next-2024-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (154 commits)
Revert "wifi: iwlegacy: do not skip frames with bad FCS"
wifi: mac80211: pass MBSSID config by reference
wifi: mac80211: Support EHT 1024 aggregation size in TX
net: rfkill: gpio: Add check for clk_enable()
wifi: brcmfmac: Fix oops due to NULL pointer dereference in brcmf_sdiod_sglist_rw()
wifi: Switch back to struct platform_driver::remove()
wifi: ipw2x00: libipw_rx_any(): fix bad alignment
wifi: brcmfmac: release 'root' node in all execution paths
wifi: iwlwifi: mvm: don't call power_update_mac in fast suspend
wifi: iwlwifi: s/IWL_MVM_INVALID_STA/IWL_INVALID_STA
wifi: iwlwifi: bump minimum API version in BZ/SC to 92
wifi: iwlwifi: move IWL_LMAC_*_INDEX to fw/api/context.h
wifi: iwlwifi: be less noisy if the NIC is dead in S3
wifi: iwlwifi: mvm: tell iwlmei when we finished suspending
wifi: iwlwifi: allow fast resume on ax200
wifi: iwlwifi: mvm: support new initiator and responder command version
wifi: iwlwifi: mvm: use wiphy locked debugfs for low-latency
wifi: iwlwifi: mvm: MLO scan upon channel condition degradation
wifi: iwlwifi: mvm: support new versions of the wowlan APIs
wifi: iwlwifi: mvm: allow always calling iwl_mvm_get_bss_vif()
...
====================
Link: https://patch.msgid.link/20241113172918.A8A11C4CEC3@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/wireless to use
.remove(), with the eventual goal to drop struct
platform_driver::remove_new(). As .remove() and .remove_new() have the
same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
En passant several whitespace changes are done to make indentation
consistent in the struct initializers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241106170706.38922-2-u.kleine-koenig@baylibre.com
The first set of wireless fixes for v6.12. We have been busy and have
not been able to send this earlier, so there are more fixes than
usual. The fixes are all over, both in stack and in drivers, but
nothing special really standing out.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmcWl7MRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZv0Qgf/fQJKXkGJkvozrbJATkKHfHKUOphIl4Y8
/r3SlrsIL6qXZAUq5N+NH9vfUeKt5kkKG8Fc8yrJaygDLsV9v1LGiBSsb5eJ+PfM
4fCOdzPSrWG984dLwsCK8UGEzfQ1G4d6HckwubUMimK2X/m6wx/99fenjMAQvdWO
rjAJmpAkgoT0Fvf8GD3joMBKKjMFr2KT8tgbfvwpyr9cXAPZYf35+74Nl84UjHiP
rGTGN++NQuPMsYyYIPPA+eMNUnlUVyDah+UVmzsMp27YUdKBKjx23kRH6tKM/46H
dWqpqEV50xshlPaotHoFg9+4KRrxnxwvFtGTsnbvHcuSnkPBUusAvw==
=l6SI
-----END PGP SIGNATURE-----
Merge tag 'wireless-2024-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
wireless fixes for v6.12-rc5
The first set of wireless fixes for v6.12. We have been busy and have
not been able to send this earlier, so there are more fixes than
usual. The fixes are all over, both in stack and in drivers, but
nothing special really standing out.
In order to update the right link information, call the update
rate_control_rate_update() with the right link_sta, and then
pass that through to the driver's sta_rc_update() method. The
software rate control still doesn't support it, but that'll be
skipped by not having a rate control ref.
Since it now operates on a link sta, rename the driver method.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241007144851.5851b6b5fd41.Ibdf50d96afa4b761dd9b9dfd54a1147e77a75329@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
If mcu_skb_prepare_msg is not implemented, incrementing skb refcount does not
work for mcu message retry. In some cases (e.g. on SDIO), shared skbs can trigger
a BUG_ON, crashing the system.
Fix this by only incrementing refcount if retry is actually supported.
Fixes: 3688c18b65 ("wifi: mt76: mt7915: retry mcu messages")
Closes: https://lore.kernel.org/r/d907b13a-f8be-4cb8-a0bb-560a21278041@notapiano/
Reported-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> #KernelCI
Tested-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240917110942.22077-1-nbd@nbd.name
Due to the lack of checks on the clc array, if the firmware supports
more clc configuration, it will cause illegal memory access.
Cc: stable@vger.kernel.org
Fixes: c948b5da6b ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20240819015334.14580-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
devm_kasprintf() can return a NULL pointer on failure but this returned
value is not checked. Fix this lack and check the returned value.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 0bb4e9187e ("mt76: mt7615: fix hwmon temp sensor mem use-after-free")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patch.msgid.link/20240905014753.353271-1-make24@iscas.ac.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patch.msgid.link/20240904075213.1352976-1-nichen@iscas.ac.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In multi-channel scenarios, the granted channel must be aborted before
suspending. Otherwise, the firmware will be put into a wrong state,
resulting in an association failure after resuming.
With this patch, the granted channel will be aborted before suspending
if necessary.
Cc: stable@vger.kernel.org
Fixes: c948b5da6b ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20240902090054.15806-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with a flexible-array member in the
middle of multiple other structs, we use the `struct_group_tagged()`
helper to create a new tagged `struct mt76_connac2_mcu_rxd_hdr`.
This structure groups together all the members of the flexible
`struct mt76_connac2_mcu_rxd` except the flexible array.
As a result, the array is effectively separated from the rest of the
members without modifying the memory layout of the flexible structure.
We then change the type of the middle struct members currently causing
trouble from `struct mt76_connac2_mcu_rxd` to `struct
mt76_connac2_mcu_rxd_hdr`.
We also want to ensure that when new members need to be added to the
flexible structure, they are always included within the newly created
tagged struct. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
This approach avoids having to implement `struct mt76_connac2_mcu_rxd_hdr`
as a completely separate structure, thus preventing having to maintain
two independent but basically identical structures, closing the door
to potential bugs in the future.
So, with these changes, fix the following warnings:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:32:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:40:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:49:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:58:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/Zr5KsZugaEXrApQJ@elsanto
Signed-off-by: Felix Fietkau <nbd@nbd.name>
devm_kasprintf() can return a NULL pointer on failure but this returned
value is not checked. Fix this lack and check the returned value.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 6ae39b7c7e ("wifi: mt76: mt7921: Support temp sensor")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviwed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patch.msgid.link/20240903014455.4144536-1-make24@iscas.ac.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
devm_kasprintf() can return a NULL pointer on failure but this returned
value is not checked. Fix this lack and check the returned value.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 6ae39b7c7e ("wifi: mt76: mt7921: Support temp sensor")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patch.msgid.link/20240903014955.4145423-1-make24@iscas.ac.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- use reconfig_complete to restart mac_work / queues
- reset full wtbl after firmware init
- clear wcid and vif mask to avoid leak
- fix sta poll list corruption
Link: https://patch.msgid.link/20240827093011.18621-19-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently, CONNAC2 series do not support encryption for fragmented Tx frames.
Therefore, add dummy function mt7915_set_frag_threshold() to prevent SW
IEEE 802.11 fragmentation.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Link: https://patch.msgid.link/20240827093011.18621-16-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On MT7915, MCU hangs do not trigger watchdog interrupts, so they can only
be detected through MCU message timeouts. Ensure that the hardware gets
restarted when that happens in order to prevent a permanent stuck state.
Link: https://patch.msgid.link/20240827093011.18621-15-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add fragmentation index into TXD.DW2 to support IEEE 802.11 fragmentation.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Link: https://patch.msgid.link/20240827093011.18621-9-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently DFS works under assumption there could be only one channel
context in the hardware. Hence, drivers just calls the function
ieee80211_radar_detected() passing the hardware structure. However, with
MLO, this obviously will not work since number of channel contexts will be
more than one and hence drivers would need to pass the channel information
as well on which the radar is detected.
Also, when radar is detected in one of the links, other link's CAC should
not be cancelled.
Hence, in order to support DFS with MLO, do the following changes -
* Add channel context conf pointer as an argument to the function
ieee80211_radar_detected(). During MLO, drivers would have to pass on
which channel context conf radar is detected. Otherwise, drivers could
just pass NULL.
* ieee80211_radar_detected() will iterate over all channel contexts
present and
* if channel context conf is passed, only mark that as radar
detected
* if NULL is passed, then mark all channel contexts as radar
detected
* Then as usual, schedule the radar detected work.
* In the worker, go over all the contexts again and for all such context
which is marked with radar detected, cancel the ongoing CAC by calling
ieee80211_dfs_cac_cancel() and then notify cfg80211 via
cfg80211_radar_event().
* To cancel the CAC, pass the channel context as well where radar is
detected to ieee80211_dfs_cac_cancel(). This ensures that CAC is
canceled only on the links using the provided context, leaving other
links unaffected.
This would also help in scenarios where there is split phy 5 GHz radio,
which is capable of DFS channels in both lower and upper band. In this
case, simultaneous radars can be detected.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-9-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the NULL pointer dereference in mt7996_mcu_sta_bfer_he
routine adding an sta interface to the mt7996 driver.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Link: https://patch.msgid.link/20240813081242.3991814-1-make24@iscas.ac.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When beacon protection is enabled, FW checks MMIE tag & length in the
beacon for every cipher mode. To pass the check, driver needs to set the
key flag IEEE80211_KEY_GENERATE_MMIE to let mac80211 generate and
initialize MMIE.
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-11-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add fragment index into TXD.DW2 to support IEEE 802.11 fragmentation.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-10-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When mbss was previously enabled, the TLV needs to be included when
disabling it again, in order to clear the firmware state.
Fixes: a7908d5b61 ("wifi: mt76: mt7996: fix non-main BSS no beacon issue for MBSS scenario")
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-9-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure correct bf number and bitmap in beamforming mcu command for
mt7992 chipsets, which only support dual-band.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-8-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If a VIF acts as a beamformer, it should check peer's beamformee
capability, and vice versa.
Fixes: ba01944ade ("wifi: mt76: mt7996: add EHT beamforming support")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-7-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to IEEE P802.11be/D6.0 Table 9-417n, beamformee SS field stands
for the maximum number of spatial streams that the STA can receive in an
EHT sounding NDP minus 1, and the minimum value of this field is 3.
This value indicates the decoding capability of a beamformee, which is
independent of current antenna settings. Correct the value for mt7996
and mt7992 chipsets based on their HW capability.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-6-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Advertize beacon_int_min_gcd as 100 to allow setting different beacon
intervals on different interfaces.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-4-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to connac3 HW design, the WMM index of AP and STA interface
should be 0 and 3, respectively.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-3-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During scanning, UNI_CHANNEL_RX_PATH tag is necessary for the firmware to
properly stop and resume MAC TX queue. Without this tag, HW needs more time
to resume traffic when switching back to working channel.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-2-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The chainmask is u16 so using hweight8 cannot get correct tx_ant.
Without this patch, the tx_ant of band 2 would be -1 and lead to the
following issue:
BUG: KASAN: stack-out-of-bounds in mt7996_mcu_add_sta+0x12e0/0x16e0 [mt7996e]
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20240816094635.2391-1-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The check should start from 5845 to 5925, which includes
channels 169, 173, and 177.
Fixes: 09382d8f86 ("wifi: mt76: mt7921: update the channel usage when the regd domain changed")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20240806013408.17874-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When disabling wifi mt7921_ipv6_addr_change() is called as a notifier.
At this point mvif->phy is already NULL so we cannot use it here.
Signed-off-by: Bert Karwatzki <spasswolf@web.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240812104542.80760-1-spasswolf@web.de
Add some time to wait for LP engine to complete its operation
before polling pmctrl register.
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Tested-by: David Ruth <druth@chromium.org>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20240523112131.31437-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Register MLD capability for the firmware supporting MLO.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/49c796b101e792c84bc2c0d74753022b75fd3355.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
remove the unused function mt7925_mcu_set_chan_info
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/0aa0abe7fc661380ae812c6bc879a7705de401b2.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update band_idx in per-link BSS to be auto for the MLO-enabled firmware
and the MLO-enabled firmware only supports omac index in 0.
The change remains compatible with the non-MLO mode and the older firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/37fcf3ea7b4883840d61f97231277b297e1b15a3.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
update mt7925_mcu_bss_basic_tlv for the MLO-enabled firmware.
The change remains compatible with the non-MLO mode and the
older firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/583a3ac10583cfef0028f9a0b5a4802fc4070b99.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set the BSS index from the per-linked BSS for the firmware to identify
which link the command is operating on.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/dde970c748586d03fbecbccb10cb9903284719aa.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
when we serve MLO during the multiple-linked connection, the chanctx may
be not available in the internal driver, we should get the proper the
band information from link_conf for the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/6620e00fbeef686fb2041556deba346411eab0f1.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get band information from the per-link BSS.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/4f6ca2d082627bb93f79d5a4df80dc08998ee5d2.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add mt7925_mcu_sta_eht_mld_tlv for the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/a1001592eeef4e4ee2c3e15dc94cca0815d64e59.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
update mt7925_mcu_sta_update for the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/2e25bfc2d8aa503ecd1ba8099c6e54dce0c27b99.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mt7925_mcu_bss_mld_tlv for the MLO-enabled firmware
The change remains compatible with the non-MLO mode and the
older firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/a3d03b0a1ca916b2b8b2e7c0afcdcd7e258d97c3.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
update mt7925_mcu_bss_mld_tlv for the MLO-enabled firmware,
the change remains compatible with the non-MLO mode and the
older firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/2d89b93bcfd92e7c6987aaa0a3c4637e605ac154.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mt7925_mcu_sta_mld_tlv for the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/25ea3ffd3875083577ab440ec63f3dcd9dc233f4.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add mt7925_[assign,unassign]_vif_chanctx to assign and unassign
chanctx to the specific link configuration. If the chctx is not
pass in the parameter, we will look up the channel information
from link_conf->chanreq.oper.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/15261879a16cb12674d6dea7703410baa6883799.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add def_wcid to struct mt76_wcid to allow per-link wcid to retrieve the
struct ieee80211_sta structure.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/d5188ca633666eaad7e90a8061d1a0585487e128.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
report link information in rx status
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/c7cdc17d94375a76802a5c4a825ea3e51cdb53af.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update rate index according to link id.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/e0bbc0932edbd9225fe7b7736693c137cf433a52.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add link handling in the mt7925_ipv6_addr_change
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/ed429b1896cc10c8db25dc2ade3e59bec78d7131.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add link handling in the BSS_CHANGED_ARP_FILTER handler.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/6e26e2ce253630ab29702693a7822f9961de6a18.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add link handling in mt7925_vif_connect_iter
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/c8d66043a4d31801249d53dd23f695c28a97a933.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add link handling in mt7925_sta_set_decap_offload
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/df2524e3a63a93699bde441e4ab70a70bbac53ef.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add links handling in mt7925_mac_sta_assoc
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/0ddf1834783b111d626b05d298478f520d7c0caa.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add link handling in mt7925_txwi_free.
MT7996 should have the similar the logic, we try to copy from there to
ensure consistency between both.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/f8084e19d388c6b0807618ac6d1bb8ac633dc8cd.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add link handling in mt7925_mcu_set_beacon_filter
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/b814718a40ad5df6100e63d15c87ba95a318bc22.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Added link handling in the BSS_CHANGED_PS handler.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/542ca29261af0cac007d2cb821ed36284d51c679.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add link handling to mt7925_change_chanctx
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/49f2a2f8230979a4e123bc1dab70a8496875cc6c.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add link handling in mt7925_set_key to support MLO-enabled
firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/164608d96ce10a40e673bc6f252189c94bc48da7.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add link handling to mt792x_tx and writing txwi.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/c0a7c0b33ea2640bcb4f13a5f79a8976b73fa8f2.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Added link handling to mt7925_mac_sta_remove, supporting the MLO-enabled
firmware. The change remains comptabile with the non-MLO mode.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20d53511fe1f64984d893f4d3ec87cb9f87d3070.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Added link handling to mt7925_mac_sta_add to support MLD devices.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/632faefe8c82cd5609c2af00aabee15ccc9616ed.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add mt7925_change_sta_links to change the valid links of a station,
supporting the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/eeedec88f0576315791a8b1b453464173a4addbe.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7925_change_vif_links to change the valid links on an interface,
supporting the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/31c9de30c3a18592c8e100f909845383b66f8677.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
