Since the switch to using AQL by default, mtxq->retry_q is never filled anymore
Remove it to get rid of a few more unnecessary cycles in the tx path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This improves performance by allowing the scheduler to move the tx scheduling
work to idle CPUs. Since tx scheduling work is very latency sensitive and
kept short via AQL, sched_set_fifo_low is used to keep worker priority above
normal tasks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that AQL works well on all mt76 drivers, completely replace the arbitrary
burst sizing and number of bursts logic for tx scheduling.
For the short period of time in which AQL does not work well yet, limit each
stations to 16 in-flight packets that have no estimated tx time.
This should avoid filling the queue if a station connects and queues up a
large number of packets before rate control information is available, especially
with hardware rate control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615 and newer drivers do not need this, since they use sequence number offload
Moving this code also reduces the number of callsites to make it easier to review
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not tx packets in mt76_txq_send_burst() or mt76_txq_schedule_list()
if the device is in runtime-pm
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_skb_adjust_pad to reuse the code adding sdio support to
mt7615 driver and remove code duplication. Move 4B header configuration
for usb devices out of mt76_skb_adjust_pad
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used for calibration in the manufacturing process.
It supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings.
It also supports receiving packets and showing some statistics, including
packet counters and detailed RSSI information.
It will only be compiled in if CONFIG_NL80211_TESTMODE is enabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sparse report warnings at mt76_tx_status_unlock() and mt76_tx_status_lock()
warning: context imbalance in mt76_tx_status_lock() - wrong count at exit
warning: context imbalance in mt76_tx_status_unlock() - unexpected unlock
The root cause is the additional __acquire(&dev->status_list.lock)
and __release(&dev->status_list.unlock) called
from inside mt76_tx_status_lock() and mt76_tx_status_unlock().
Remove __acquire(&dev->status_list.lock) annotation
Remove __releases(&dev->status_list.unlock)
Correct &dev->status_list.unlock to &dev->status_list.lock
-unlock not defined in the sk_buff_head struct
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove empty flag in mt76_txq_schedule_list and mt76_txq_send_burst
since we just need retry_q length to notify mac80211 to reschedule the
current tx queue
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
tx queues are already disabled by mac80211 during scanning or other
off-channel activity. There is no need to repeat the check in mt76,
since scheduled queues are selected by mac80211 as well.
Signed-off-by: Balakrishna Bandi <b.balakrishna@globaledgesoft.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the following checkpatch warnings:
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76{15,03}_tx_tasklet in mt76_alloc_device in order to be used as
default tx_tasklet initialization. Remove duplicated code in
mt7603/mt7615 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
No functional change intended.
Add SPDX identifiers to all remaining files in /mt76.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce skb field in mt76_txwi_cache. Moreover add txwi_flags
to mt76_driver_ops since new chipsets will release mt76_txwi_cache/skbs
at tx completion instead of dma one.
This is a preliminary patch to add mt7615 support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Dynamically allocate txwi since new chipsets will use longer txwi
descriptors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76_txq_id field to mt76_queue_entry in order to properly
track outstanding frames for mt7615 that relies on a single hw queue
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_sw_queue data structure in order to support new
chipsets (e.g. mt7615) that have a shared hardware queue for all traffic
identifiers. mt76_sw_queue will be used to track outstanding packets
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_queue dependency from tx_queue_skb function pointer and
rely on mt76_tx_qid instead. This is a preliminary patch to introduce
mt76_sw_queue support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_queue stopped parameter in order to run
ieee80211_wake_queue only when mac80211 queues have been
previously stopped and avoid to disable interrupts when
it is not necessary
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove bogus check for MT_PACKET_ID_NO_ACK in mt76_tx_status_skb_get, which
is already handled in callers and turns timeout calls into no-ops
Do not clean up pending status items on reordering of tx status information
if the timeout is not reached yet
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In case a tx queue wake call arrives after a client has transitioned to
powersave, make sure that the queue is not kept active until the client
has left powersave mode
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On MT76x2, the hardware does not report tx status in the FIFO register,
if the packet id is 0.
Change the allocation of packet IDs to use 0 for no-ack packets, 1 for
non-probing packets and 2-255 for packets with tx status requested.
Fixes rate control issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from mac80211 commit adf8ed01e4 ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there are still pending packets in the tx queue when removing a station,
it could possibly lead to a call to further attempts to pull packets from
the mac80211 tx queue after it has already been removed from the scheduling
list.
Prevent this from happening by calling synchronize_rcu after deleting the
wcid pointer before further cleaning up the tx queues.
To be extra careful, ensure that mtxq->list is always initialized properly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is some code in the mac80211 tx status processing code that could
potentially call back into the tx codepath.
To avoid deadlocks, make sure that no tx related spinlocks are taken
during the ieee80211_tx_status call.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT76x2/MT76x0 has somewhat unreliable tx status reporting, and for that
reason the driver currently does not report per-skb tx ack status at all.
This breaks things like client idle polling, which relies on the tx ack
status of a transmitted nullfunc frame.
This patch adds code to report skb-attached tx status if requested by
mac80211 or the rate control module. Since tx status is polled from a
simple FIFO register, the code needs to account for the possibility of
tx status events getting lost.
The code keeps a list of skbs for which tx status is required and passes
them to mac80211 once tx status has been filled in and the DMA queue is
done with it.
If a tx status event is not received after one second, the status rates
are cleared, and a succesful ACK is indicated to avoid spurious disassoc
during assoc or client polling.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ps-poll response frames can be sent via drv_tx. Store the frame sequence number
for such frames, in case a BlockAckReq needs to be sent
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use the same AC to hardware queue mappings for all subdrivers.
Note: this change BK and BE mappings for USB drivers.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add tx_queue_skb function pointer in mt76_bus_ops since mt76x2u based
devices do not map mt76x2_txwi on dma buffers and it is not possible
to reuse mt76_dma_tx_queue_skb() routine to enqueue tx frames to
hw buffers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move mt76_dma_tx_queue_skb routine in dma.c.
Remove static qualifier from mt76_get_txwi definition
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During scans, mac80211 frequently switches back to the home channel to
minimize interruption of ongoing traffic. Keep regular tx queues active
during that time.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The check within mt76_txq_send_burst is not enough, as it happens after
a first frame has already been queued up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This will be used by drivers for MT76x2e, MT7603e and MT7628
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
