This is a preliminary patch to introduce WED RX support for mt7915.
Tested-by: Daniel Golle <daniel@makrotopia.org>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reports signal strength of ACK packets from the peer as measured
at each interface.
Tested-by: Shurong Wen <shurong.wen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit f17f486450 and adds the
MT_DRV_AMSDU_OFFLOAD flag for MT7921 USB/SDIO
The reverted commit significantly decreases performance when running
a test where two MT7915 radios have 16 station vdevs each, configured
for AC mode, and transmitting UDP traffic to AP.
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Carson Vandegriffe <carson.vandegriffe@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some users have reported being unable to connect to MT76x0 APs running mt76
after a commit enabling the VHT extneded NSS BW feature.
Fix this regression by ensuring that this feature only gets enabled on drivers
that support it
Cc: stable@vger.kernel.org
Fixes: d9fcfc1424 ("mt76: enable the VHT extended NSS BW feature")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220907095228.82072-1-nbd@nbd.name
We should use of_node_put() for the reference 'np' returned by
of_get_child_by_name() which will increase the refcount.
Fixes: 17f1de56df ("mt76: add common code shared between multiple chipsets")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce phy_idx mt76_rx_status instead of ext_idx. This is a
preliminary patch to add newer chipset support
Co-developed-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
if the received frame enables RX_FLAG_ONLY_MONITOR,
driver doesn't need to check the ccmp pn of this frame.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According IEEE Std 802.11-2020, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS BW
Support subfield of the VHT Capabilities Information field.
Some APs, such as Xiaomi AX6000, would check this one for BW settings.
mt76 driver can get max BW capability only if the this field is confgured
properly.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WED support requires using non-coherent DMA, whereas the PCI device might
be configured for coherent DMA.
The WED driver will take care of changing the PCI HIF coherent IO setting
on attach.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is a small race window where ongoing tx activity can lead to a skb
getting added to the status tracking idr after that idr has already been
cleaned up, which will keep the wcid linked in the status poll list.
Fix this by only adding status skbs if the wcid pointer is still assigned
in dev->wcid, which gets cleared early by mt76_sta_pre_rcu_remove
Fixes: bd1e3e7b69 ("mt76: introduce packet_id idr")
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To make sure we have the proper antenna config in 6g cap,
move IEEE80211_VHT_CAP_[T/R]X_ANTENNA_PATTERN to stream init.
Fixes: edf9dab8ba ("mt76: add 6GHz support")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop invalid rssi value to calculate a reasonable report
Fixes: 4550fb9e98 ("mt76: improve signal strength reporting")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When operating on a mix of DFS and non-DFS channels, the driver only checks
the CAC status of the control channel. This causes beacons/tx to fail if the
control channel is on a non-DFS channel.
Fix this by calling cfg80211_reg_can_beacon to determine the DFS status of
all affected channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of just taking the maximum per-chain signal strength values,
add an approximation for the sum of the combined signal.
This should more accurately reflect the real signal strength, especially
if the per-chain signal strength values are close to each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Client mode on DFS channels was broken, because the old code was activating
the DFS detector on radar channels while leaving it in CAC state.
This was caused by making the decision based on the channel radar flag,
instead of hw->conf.radar_enabled.
In order to properly deal with the various corner cases, rip out the state
handling code and replace it with something that's much easier to reason
about.
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning:
drivers/net/wireless/mediatek/mt76/mac80211.c:183:32:
warning: symbol 'mt76_sar_capa' was not declared. Should it be static?
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move wiphy SAR capability configuration in mt76 module and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the driver has configured the hardware to drop packets for a sta that was
in powersave mode, then clearing the flag too early opens up a small race
window during which packets could be dropped on wakeup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_get_sar_power and mt76_init_sar_power in the common code.
This is a preliminary patch to add sar support to mt76x02 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
the wiphy's available antennas may be incorrect
When ext phy's antenna_mask is different from main phy
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Cap max offset value to ARRAY_SIZE(mt76_rates) - 1 in
mt76_calculate_default_rate routine in order to avoid possible Out Of
Bound accesses.
Fixes: 33920b2bf0 ("mt76: add support for setting mcast rate")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_ethtool_worker_info in common code in order to be reused in
mt7921 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When received frame is decryped by hardware, CCMP PN is checked by
mt76.
When management frame protection (IEEE 802.11w) is used, we must use
a separate counter for tracking received CCMP packet number for the
management frames. The previously used counter was shared with data
frames and that can cause problems in detecting replays incorrectly
for robust management frames.
Add a new counter just for robust management frames to avoid this
issue.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Substitute sk_buff_head status_list with spinlock_t status_lock since we
just need it for locking
Tested-by: mrkiko.rs@gmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is
always set to NULL
Tested-by: mrkiko.rs@gmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce per-wcid idr to manage packet id for txs. This allow fast idr
lookup and skb queueing at the same time.
Tested-by: mrkiko.rs@gmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce 6GHz channel list in mt76 module. This is a preliminary patch
to unlock 6GHz band for mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Give a proper boottime_ns value for netlink RX to avoid scan
issues with Android.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop MT_DRV_AMSDU_OFFLOAD after introducing IEEE80211_OFFLOAD_ENCAP_ENABLED
flag in mac80211. Driver now checks vif->offload_flags to know encap offload
status of each interface.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Mesh and ad-hoc interfaces allow users to set mcast rate through
NL80211_ATTR_MCAST_RATE, so rework mt76_default_basic_rate() to
adapt that.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add mt76_default_basic_rate to mt76 core more devices can rely on
to send frames which require the rate in the basic rates.
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add .set_sar_specs to allow configuring SAR power limitations on the
frequency ranges from the userland.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move wiphy interface_modes configuration in mt76_alloc_device and
mt76_alloc_phy in order to be overwritten by hw specific code
since some drivers do not support all operating modes (mt7921
supports sta only in the current codebase)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_rates array in mt76 module and remove duplicated code since it
is shared by all drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Mitigate A-MSDU injection attacks (CVE-2020-24588) by detecting if the
destination address of a subframe equals an RFC1042 (i.e., LLC/SNAP)
header, and if so dropping the complete A-MSDU frame. This mitigates
known attacks, although new (unknown) aggregation-based attacks may
remain possible.
This defense works because in A-MSDU aggregation injection attacks, a
normal encrypted Wi-Fi frame is turned into an A-MSDU frame. This means
the first 6 bytes of the first A-MSDU subframe correspond to an RFC1042
header. In other words, the destination MAC address of the first A-MSDU
subframe contains the start of an RFC1042 header during an aggregation
attack. We can detect this and thereby prevent this specific attack.
For details, see Section 7.2 of "Fragment and Forge: Breaking Wi-Fi
Through Frame Aggregation and Fragmentation".
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210513070303.20253-1-nbd@nbd.name
In order to remove duplicated code, move mt76_token_init in
mt76_alloc_device routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Frame reception timestamp (low 32-bits) that indicates the value of the
local TSF timer value at the time the first bit of the MAC header in the
received frame (PPDU unit) arriving at the MAC.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable hw rx-amsdu de-aggregation support available in 7915 devices.
This is a preliminary patch to enable rx checksum offload
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Only clear dev->phy2 after the phy is gone, the driver may still need to access
it until shutdown is complete
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add testmode support for DBDC NICs (both MT7615D and MT7915D work).
Testmode data and parameters are moved from per-dev to per-phy
for maintaining the value of each band.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce dbdc support to mt7915 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_init_mcu_queue utility routine in order to allocate
dedicate q_mcu pointers for mcu hw queues. This is a preliminary patch
to move data queues in mt76_phy and add dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_init_tx_queue in mac80211.c since it is shared by all
drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It was accidentally dropped while adding multiple wiphy support
Fixes fast-rx support and avoids handling reordering in both mac80211
and the driver
Cc: stable@vger.kernel.org
Fixes: c89d362541 ("mt76: add function for allocating an extra wiphy")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The newer chipsets can deal with the same STA on multiple interfaces
Preparation for supporting more station interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce sdio tx aggregation to reduce bus transaction ands improve tx
throughput. For the moment the skb are copied in a dedicated buffer
since mmc APIs do not support sg table for zero-copy.
Since skb data are already copied in xmit_buff[], avoid linearization in
ma80211 layer. Relying on tx aggregation, we improve tx tpt of ~65%.
Tested-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since the switch to using AQL by default, mtxq->retry_q is never filled anymore
Remove it to get rid of a few more unnecessary cycles in the tx path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This improves performance by allowing the scheduler to move the tx scheduling
work to idle CPUs. Since tx scheduling work is very latency sensitive and
kept short via AQL, sched_set_fifo_low is used to keep worker priority above
normal tasks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This disables the software A-MSDU aggregation in mac80211 and enables hardware
offloading
Suggested-by: Yiwei Chung <yiwei.chung@mediatek.com>
Suggested-by: YF Luo <yf.luo@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce mt76_sdio module as common layer to add mt7663s support
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_update_survey utility routine in order to compute
survey stats without waking up the device since it runs holding mt76 lock.
Run mt7615_pm_wake directly in mt7615_update_channel since it can run
with mt76.mutex held if called by mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used for calibration in the manufacturing process.
It supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings.
It also supports receiving packets and showing some statistics, including
packet counters and detailed RSSI information.
It will only be compiled in if CONFIG_NL80211_TESTMODE is enabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce U-APSD support in mt76 driver for AP interface
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
While looking at the ETSI regulatory domain definitions
and a patch, which allows more channels for ath10k, I also
checked the channels allowed for mt76.
ETSI regulations would possibly allow to add channels 32, 68,
96, 144, 169 and 173. IEEE 802.11-2016 defines no operating class
for channels 32, 68 and 96. This leaves us channels 144, 169 and 173,
which are included in this patch.
I tested 169 and 173 with a mt76 based USB dongle (AVM AC 860) and they
worked fine. If I saw that right, these channels are also covered by
register definitions inside the driver.
Channel 144 should also work, but gets disabled by the kernel as of now.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce p2p-go/p2p-client suppor to mt76 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable mac80211 TDLS support by default. Disable TDLS hw filtering for
mt7615 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The hardware requirements for A-MPDU density are entirely on the tx side,
not the rx side. Because of that, the IE value should stay at 0 and the
minimum value should instead be enforced in WTBL/TXWI
MT7615 has no restrictions here
Signed-off-by: Felix Fietkau <nbd@nbd.name>
remove IEEE80211_HW_PS_NULLFUNC_STACK capability from mt76_phy_init
routine since 802.11 ps is not currently supported by any devices and it
will conflict with mt7663 ps fw support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify code converting between the different txpower values. Always add/remove
the combined txpower delta before dividing half-dB values.
Also fix the combined txpower delta values. The correct half-dB delta for
3 chains is 9, not 8.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move WIPHY_FLAG_HAS_CHANNEL_SWITCH in mt76-core module since now all
drivers support Channel Switch Announcement
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Prevent the overwriting of max_tx_fragments if it has already been set
in chip-specific init routine.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for an extra wiphy in mt76_set_channel and mt76_get_survey
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
On the first wiphy, hw->priv will point to struct mt76_dev, which contains a
struct mt76_phy at the start. For the secondary wiphy, hw->priv will point
to a mt76_phy encapsulated in a driver specific struct
To simplify access to struct mt76_phy members from drivers, the driver specific
device struct is changed to add a union of struct mt76_dev and struct mt76_phy
as the first element
Signed-off-by: Felix Fietkau <nbd@nbd.name>
