The Marvell SD8978 (aka NXP IW416) uses identical registers as SD8987,
so reuse the existing mwifiex_reg_sd8987 definition.
Note that mwifiex_reg_sd8977 and mwifiex_reg_sd8997 are likewise
identical, save for the fw_dump_ctrl register: They define it as 0xf0
whereas mwifiex_reg_sd8987 defines it as 0xf9. I've verified that
0xf9 is the correct value on SD8978. NXP's out-of-tree driver uses
0xf9 for all of them, so there's a chance that 0xf0 is not correct
in the mwifiex_reg_sd8977 and mwifiex_reg_sd8997 definitions. I cannot
test that for lack of hardware, hence am leaving it as is.
NXP has only released a firmware which runs Bluetooth over UART.
Perhaps Bluetooth over SDIO is unsupported by this chipset.
Consequently, only an "sdiouart" firmware image is referenced, not an
alternative "sdsd" image.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/536b4f17a72ca460ad1b07045757043fb0778988.1674827105.git.lukas@wunner.de
Commit e3fffc1f0b ("devicetree: document new marvell-8xxx and
pwrseq-sd8787 options") documented a compatible string for SD8787 in
the devicetree bindings, but neglected to add it to the mwifiex driver.
Fixes: e3fffc1f0b ("devicetree: document new marvell-8xxx and pwrseq-sd8787 options")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.11+
Cc: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/320de5005ff3b8fd76be2d2b859fd021689c3681.1674827105.git.lukas@wunner.de
Add compatibility with WPS by passing on WPS enrollee information in
probe requests. Ignore other IEs supplied in the scan request. This also
has the added benefit of restoring compatibility with newer
wpa_supplicant versions that always add scan IEs. Previously, with
max_scan_ie_len set to 0, scans would always fail.
Suggested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123053132.30710-5-doug@schmorgal.com
Add a define for the TLV type that will be used to add WPS enrollee
information to probe requests.
Suggested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123053132.30710-4-doug@schmorgal.com
The existing code only converts the first IE to a TLV, but it returns a
value that takes the length of all IEs into account. When there is more
than one IE (which happens with modern wpa_supplicant versions for
example), the returned length is too long and extra junk TLVs get sent
to the firmware, resulting in an association failure.
Fix this by finding the first RSN or WPA IE and only adding that. This
has the extra benefit of working properly if the RSN/WPA IE isn't the
first one in the IE buffer.
While we're at it, clean up the code to use the available structs like
the other lbs_add_* functions instead of directly manipulating the TLV
buffer.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123053132.30710-3-doug@schmorgal.com
Several of the structs are using the deprecated convention of items[1]
for a dynamically sized trailing element. Convert these structs to the
modern C99 style of items[]. Also fix a couple of camel case struct
element names.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123053132.30710-2-doug@schmorgal.com
Due to the two cherry picked commits from wireless to wireless-next we have
several conflicts in mt76. To avoid any bugs with conflicts merge wireless into
wireless-next.
96f134dc19 wifi: mt76: handle possible mt76_rx_token_consume failures
fe13dad899 wifi: mt76: dma: do not increment queue head if mt76_dma_add_buf fails
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: f52b041aed ("libertas: Add spinlock to avoid race condition")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-5-yangyingliang@huawei.com
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: d2e7b3425c ("libertas: disable functionality when interface is down")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-4-yangyingliang@huawei.com
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: a3128feef6 ("libertas: use irqsave() in USB's complete callback")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-3-yangyingliang@huawei.com
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: fc75122fab ("libertas_tf: use irqsave() in USB's complete callback")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-2-yangyingliang@huawei.com
When kfifo_alloc() failed in lbs_init_adapter(), cmd buffer is not
released. Add free memory to processing error path.
Fixes: 7919b89c82 ("libertas: convert libertas driver to use an event/cmdresp queue")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221208121448.2845986-1-shaozhengchao@huawei.com
strtobool() is the same as kstrtobool().
However, the latter is more used within the kernel.
In order to remove strtobool() and slightly simplify kstrtox.h, switch to
the other function name.
While at it, include the corresponding header file (<linux/kstrtox.h>)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1ff34549af5ad6f7c80d5b9e11872b5499065fc1.1667336095.git.christophe.jaillet@wanadoo.fr
First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7.
All mac80211 driver are now converted to use internal TX queues, this
might cause some regressions so we wanted to do this early in the
cycle.
Note: wireless tree was merged[1] to wireless-next to avoid some
conflicts with mac80211 patches between the trees. Unfortunately there
are still two smaller conflicts in net/mac80211/util.c which Stephen
also reported[2]. In the first conflict initialise scratch_len to
"params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and
in the second conflict take the version which uses elems->scratch_pos.
Git diff output should like this:
--- a/net/mac80211/util.c
+++ b/net/mac80211/util.c
@@@ -1506,7 -1648,7 +1650,7 @@@ ieee802_11_parse_elems_full(struct ieee
const struct element *non_inherit = NULL;
u8 *nontransmitted_profile;
int nontransmitted_profile_len = 0;
- size_t scratch_len = params->len;
- size_t scratch_len = params->scratch_len ?: 2 * params->len;
++ size_t scratch_len = params->scratch_len ?: 3 * params->len;
elems = kzalloc(sizeof(*elems) + scratch_len, GFP_ATOMIC);
if (!elems)
[1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91
[2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/
Major changes:
mac80211
* preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues
* add API to show the link STAs in debugfs
* all mac80211 drivers are now using mac80211 internal TX queues (iTXQs)
rtw89
* support 8852BE
rtl8xxxu
* support RTL8188FU
brmfmac
* support two station interfaces concurrently
bcma
* support SPROM rev 11
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmNb2KwRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZs6hggAqrmgHaiRbPYlLVE0hFVaGeVXslfpK9nj
ZGr3bwG5FpioxjAsI7NfwEwpq+FoxTUigG/SShw1Rr8lw43Nt7E57+5McK3qWdKC
5/WndfChPppjtJUpc6PN+UcmCuhcm4TAyMAojbTe5lJ9cJ4yyOWZChDwah3BVZQk
/tHK4qKq8gpppwgkiJ88VdTVoVv5anIvXHH3lAIteljxk0zkaEM7lIQhIFst/zpX
cu/cWvKz2Rh6vnYjkzl8BcrbW8e0/VwnzWggtWs4/kIuRVnHRrrGwlnsULShOscM
fmK+RI2CbJIMucttUOHOXjCg4wwppSit1rH4xOkcwlvrFa7AvDbdHg==
=Zils
-----END PGP SIGNATURE-----
Kalle Valo says:
====================
pull-request: wireless-next-2022-10-28
First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7.
All mac80211 driver are now converted to use internal TX queues, this
might cause some regressions so we wanted to do this early in the
cycle.
Note: wireless tree was merged[1] to wireless-next to avoid some
conflicts with mac80211 patches between the trees. Unfortunately there
are still two smaller conflicts in net/mac80211/util.c which Stephen
also reported[2]. In the first conflict initialise scratch_len to
"params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and
in the second conflict take the version which uses elems->scratch_pos.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91
[2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/
mac80211
- preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues
- add API to show the link STAs in debugfs
- all mac80211 drivers are now using mac80211 internal TX queues (iTXQs)
rtw89
- support 8852BE
rtl8xxxu
- support RTL8188FU
brmfmac
- support two station interfaces concurrently
bcma
- support SPROM rev 11
====================
Link: https://lore.kernel.org/r/20221028132943.304ECC433B5@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
mac80211 is fully switching over to the internal TX queue (iTXQ)
implementation. Update all drivers not yet providing the now mandatory
wake_tx_queue() callback.
As an side effect the netdev interfaces of all updated drivers will
switch to the noqueue qdisc.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[add staging drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are sleep in atomic context bugs when uploading device dump
data in mwifiex. The root cause is that dev_coredumpv could not
be used in atomic contexts, because it calls dev_set_name which
include operations that may sleep. The call tree shows execution
paths that could lead to bugs:
(Interrupt context)
fw_dump_timer_fn
mwifiex_upload_device_dump
dev_coredumpv(..., GFP_KERNEL)
dev_coredumpm()
kzalloc(sizeof(*devcd), gfp); //may sleep
dev_set_name
kobject_set_name_vargs
kvasprintf_const(GFP_KERNEL, ...); //may sleep
kstrdup(s, GFP_KERNEL); //may sleep
The corresponding fail log is shown below:
[ 135.275938] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[ 135.281029] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265
...
[ 135.293613] Call Trace:
[ 135.293613] <IRQ>
[ 135.293613] dump_stack_lvl+0x57/0x7d
[ 135.293613] __might_resched.cold+0x138/0x173
[ 135.293613] ? dev_coredumpm+0xca/0x2e0
[ 135.293613] kmem_cache_alloc_trace+0x189/0x1f0
[ 135.293613] ? devcd_match_failing+0x30/0x30
[ 135.293613] dev_coredumpm+0xca/0x2e0
[ 135.293613] ? devcd_freev+0x10/0x10
[ 135.293613] dev_coredumpv+0x1c/0x20
[ 135.293613] ? devcd_match_failing+0x30/0x30
[ 135.293613] mwifiex_upload_device_dump+0x65/0xb0
[ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0
[ 135.293613] call_timer_fn+0x122/0x3d0
[ 135.293613] ? msleep_interruptible+0xb0/0xb0
[ 135.293613] ? lock_downgrade+0x3c0/0x3c0
[ 135.293613] ? __next_timer_interrupt+0x13c/0x160
[ 135.293613] ? lockdep_hardirqs_on_prepare+0xe/0x220
[ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0
[ 135.293613] __run_timers.part.0+0x3f8/0x540
[ 135.293613] ? call_timer_fn+0x3d0/0x3d0
[ 135.293613] ? arch_restore_msi_irqs+0x10/0x10
[ 135.293613] ? lapic_next_event+0x31/0x40
[ 135.293613] run_timer_softirq+0x4f/0xb0
[ 135.293613] __do_softirq+0x1c2/0x651
...
[ 135.293613] RIP: 0010:default_idle+0xb/0x10
[ 135.293613] RSP: 0018:ffff888006317e68 EFLAGS: 00000246
[ 135.293613] RAX: ffffffff82ad8d10 RBX: ffff888006301cc0 RCX: ffffffff82ac90e1
[ 135.293613] RDX: ffffed100d9ff1b4 RSI: ffffffff831ad140 RDI: ffffffff82ad8f20
[ 135.293613] RBP: 0000000000000003 R08: 0000000000000000 R09: ffff88806cff8d9b
[ 135.293613] R10: ffffed100d9ff1b3 R11: 0000000000000001 R12: ffffffff84593410
[ 135.293613] R13: 0000000000000000 R14: 0000000000000000 R15: 1ffff11000c62fd2
...
[ 135.389205] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end
This patch uses delayed work to replace timer and moves the operations
that may sleep into a delayed work in order to mitigate bugs, it was
tested on Marvell 88W8801 chip whose port is usb and the firmware is
usb8801_uapsta.bin. The following is the result after using delayed
work to replace timer.
[ 134.936453] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[ 135.043344] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end
As we can see, there is no bug now.
Fixes: f5ecd02a8b ("mwifiex: device dump support for usb interface")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/5cfa5c473ff6d069cb67760ffa04a2f84ef450a8.1661252818.git.duoming@zju.edu.cn
These cause sparse warnings, and since the device generally
works in little endian we can assume the code is correct, so
just fix the casts accordingly. No binary changes on x86.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.3f72609a3825.If4048592701bf04981be1dab18eaaa339b2ea382@changeid
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
-----BEGIN PGP SIGNATURE-----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=J5Fc
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-08-26-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes berg says:
====================
Various updates:
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for various key operations on MLD by adding new parameter
link_id. Pass the link_id received from userspace to driver for add_key,
get_key, del_key, set_default_key, set_default_mgmt_key and
set_default_beacon_key to support configuring keys specific to each MLO
link. Userspace must not specify link ID for MLO pairwise key since it
is common for all the MLO links.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20220730052643.1959111-4-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
Eliminate the follow smatch warning:
drivers/net/wireless/marvell/mwifiex/pcie.c:3364 mwifiex_unregister_dev() warn: inconsistent indenting
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220615005316.9596-1-yang.lee@linux.alibaba.com
Put the link_station_parameters structure in the station_parameters
structure (and remove the station_parameters fields already existing
in link_station_parameters).
Now, for an MLD station, the default link is added together with
the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on the normalized pattern:
this software file (the file ) is distributed by nxp under the terms
of the gnu general public license version 2 june 1991 (the license )
you may use redistribute and/or modify this file in accordance with
the terms and conditions of the license a copy of which is available
by writing to the free software foundation inc 51 franklin street
fifth floor boston ma 02110-1301 usa or on the worldwide web at
http://www gnu org/licenses/old-licenses/gpl-2 0 txt the file is
distributed as-is without warranty of any kind and the implied
warranties of merchantability or fitness for a particular purpose are
expressly disclaimed the license provides additional details about
this warranty disclaimer
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware has a 512 limit here, but we use less, so gcc
starts complaining about it:
drivers/net/wireless/marvell/libertas/cfg.c:1198:63: warning: array subscript ‘struct cmd_ds_802_11_associate_response[0]’ is partly outside array bounds of ‘unsigned char[203]’ [-Warray-bounds]
1198 | "aid 0x%04x\n", status, le16_to_cpu(resp->statuscode),
| ^~
Since we size the command and response buffer per our needs
and not per the firmware maximum, change to a variable size
data array and put the 512 only into a comment.
In the end, that's actually what the code always wanted, and
it simplifies the code that used to subtract the fixed size
buffer size in two places.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220523180200.115fa27fbece.Ie66d874b047e7afad63900aa2df70f031711147e@changeid
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
* wfx: silicon labs devices
* plfxlc: pureLiFi X, XL, XC devices
mac80211
* host based BSS color collision detection
* prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
* support TP-Link T2E devices
rtw89
* support firmware crash simulation
* preparation for 8852ce hardware support
ath11k
* Wake-on-WLAN support for QCA6390 and WCN6855
* device recovery (firmware restart) support for QCA6390 and WCN6855
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
wcn36xx
* support for transmit rate reporting to user space
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmJxS2sRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuNgwf9H2oxMKLKrlFoX1qHtNBwZuHS6IERhOkM
NI9DjS4MCyiUSbA5r3sWlpqXQeKIbG/05gUZ6Y0ircGFwnAGjZ6isPwo8pKFgbh5
QljXQjUTHbkshrXW8K+VGJxw4F1oiPlOGUDVdXPy2FLx5ZvBlaUV2rWQUzsWX9I0
EnrM6ygHBVejVYDe+JSkb1gzb/07xuZN410IJPuZTPKJfYiE0oGU3zpTbExFitaz
ObjfFUWqHrVue525WFAJ9Dbk8kYEKyMThr7rkkWekYJjujJLJo0qhEiZVZu0eEsk
Vq4PdKmQAqlgbShQ/3Mv8BRsSH2wy62+zKjPWL+8t4Gmm9DbLu+++A==
=T7Ii
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
- wfx: silicon labs devices
- plfxlc: pureLiFi X, XL, XC devices
mac80211
- host based BSS color collision detection
- prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
- support TP-Link T2E devices
rtw89
- support firmware crash simulation
- preparation for 8852ce hardware support
ath11k
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support for QCA6390 and WCN6855
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- support for WCN6750
wcn36xx
- support for transmit rate reporting to user space
* tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (228 commits)
rtw89: 8852c: rfk: add DPK
rtw89: 8852c: rfk: add IQK
rtw89: 8852c: rfk: add RX DCK
rtw89: 8852c: rfk: add RCK
rtw89: 8852c: rfk: add TSSI
rtw89: 8852c: rfk: add LCK
rtw89: 8852c: rfk: add DACK
rtw89: 8852c: rfk: add RFK tables
plfxlc: fix le16_to_cpu warning for beacon_interval
rtw88: remove a copy of the NAPI_POLL_WEIGHT define
carl9170: tx: fix an incorrect use of list iterator
wil6210: use NAPI_POLL_WEIGHT for napi budget
ath10k: remove a copy of the NAPI_POLL_WEIGHT define
ath11k: Add support for WCN6750 device
ath11k: Datapath changes to support WCN6750
ath11k: HAL changes to support WCN6750
ath11k: Add QMI changes for WCN6750
ath11k: Fetch device information via QMI for WCN6750
ath11k: Add register access logic for WCN6750
ath11k: Add HW params for WCN6750
...
====================
Link: https://lore.kernel.org/r/20220503153622.C1671C385A4@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With a recent change now it is possible to detect the strapping
option on SD8997, which allows to pick up a correct firmware
for either SDIO-SDIO or SDIO-UART.
This commit enables SDIO-UART firmware on SD8997.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220422090313.125857-3-andrejs.cainikovs@toradex.com
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To make it unambiguous that mmc_hw_reset() is for cards and not for
controllers, we make the function argument mmc_card instead of mmc_host.
Also, all users are converted.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408080045.6497-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that
net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx)
is held during the function's execution.
mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not
hold that lock, therefore violating the assertion.
Add a lock around the call.
Disclaimer:
I am currently working on a static analyser to detect missing locks.
This was a reported case. I manually verified the report by looking
at the code, so that I do not send wrong information or patches.
After concluding that this seems to be a true positive, I created
this patch.
However, as I do not in fact have this particular hardware,
I was unable to test it.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220321225515.32113-1-dossche.niels@gmail.com
Don't populate the read-only array wmm_oui on the stack but
instead make it static const. Also makes the object code a little
smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220311225610.10895-1-colin.i.king@gmail.com
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi017@gmail.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Sharvari Harisangam <sharvari.harisangam@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The earlier __packed annotations added in commit d71038c059 ("libertas:
Fix alignment issues in libertas core") were not duplicated when
libertas_af was added in commit 7670e62c7e ("libertas_tf: header file"),
even though they share several structure definitions. Add the missing
annotations which commit 642a57475b ("libertas_tf: Use struct_group()
for memcpy() region") exposed. Quoting the prior libertas fix: "Data
structures that come over the wire from the WLAN firmware must be
packed."
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-mm/202111302102.apaePz2J-lkp@intel.com
Fixes: 642a57475b ("libertas_tf: Use struct_group() for memcpy() region")
Fixes: 7670e62c7e ("libertas_tf: header file")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201173234.578124-3-keescook@chromium.org
Quoting Jia-Ju Bai <baijiaju1990@gmail.com>:
mwifiex_dequeue_tx_packet()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 1432 (Lock A)
mwifiex_send_addba()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 608 (Lock B)
mwifiex_process_sta_tx_pause()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 398 (Lock B)
mwifiex_update_ralist_tx_pause()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 941 (Lock A)
Similar report for mwifiex_process_uap_tx_pause().
While the locking expectations in this driver are a bit unclear, the
Fixed commit only intended to protect the sta_ptr, so we can drop the
lock as soon as we're done with it.
IIUC, this deadlock cannot actually happen, because command event
processing (which calls mwifiex_process_sta_tx_pause()) is
sequentialized with TX packet processing (e.g.,
mwifiex_dequeue_tx_packet()) via the main loop (mwifiex_main_process()).
But it's good not to leave this potential issue lurking.
Fixes: f0f7c2275f ("mwifiex: minor cleanups w/ sta_list_spinlock in cfg80211.c")
Cc: Douglas Anderson <dianders@chromium.org>
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Link: https://lore.kernel.org/linux-wireless/0e495b14-efbb-e0da-37bd-af6bd677ee2c@gmail.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YaV0pllJ5p/EuUat@google.com
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use named struct in struct mwl8k_cmd_set_key around members key_material,
tkip_tx_mic_key, and tkip_rx_mic_key so they can be referenced
together. This will allow memcpy() and sizeof() to more easily reason
about sizes, improve readability, and avoid future warnings about writing
beyond the end of key_material.
"pahole" shows no size nor member offset changes to struct
mwl8k_cmd_set_key. "objdump -d" shows no object code changes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119004905.2348143-1-keescook@chromium.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field array bounds checking for memcpy(), memmove(), and memset(),
avoid intentionally writing across neighboring fields.
Use struct_group() in struct txpd around members tx_dest_addr_high
and tx_dest_addr_low so they can be referenced together. This will
allow memcpy() and sizeof() to more easily reason about sizes, improve
readability, and avoid future warnings about writing beyond the end
of tx_dest_addr_high.
"pahole" shows no size nor member offset changes to struct txpd.
"objdump -d" shows no object code changes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118184121.1283821-1-keescook@chromium.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use struct_group() in struct txpd around members tx_dest_addr_high
and tx_dest_addr_low so they can be referenced together. This will
allow memcpy() and sizeof() to more easily reason about sizes, improve
readability, and avoid future warnings about writing beyond the end
of queue_id.
"pahole" shows no size nor member offset changes to struct txpd.
"objdump -d" shows no object code changes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118184104.1283637-1-keescook@chromium.org
The firmware of the 88W8897 PCIe+USB card sends those events very
unreliably, sometimes bluetooth together with 2.4ghz-wifi is used and no
COEX event comes in, and sometimes bluetooth is disabled but the
coexistance mode doesn't get disabled.
This means we sometimes end up capping the rx/tx window size while
bluetooth is not enabled anymore, artifically limiting wifi speeds even
though bluetooth is not being used.
Since we can't fix the firmware, let's just ignore those events on the
88W8897 device. From some Wireshark capture sessions it seems that the
Windows driver also doesn't change the rx/tx window sizes when bluetooth
gets enabled or disabled, so this is fairly consistent with the Windows
driver.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103205827.14559-1-verdre@v0yd.nl
We assume at a few places that priv->version_str is 0-terminated, but
right now we trust the firmware that this is the case with the version
string we get from it.
Let's rather ensure this ourselves and replace the last character with
'\0'.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-4-verdre@v0yd.nl
The 88W8897 PCIe+USB card in the hardware revision 20 apparently has a
hardware issue where the card wakes up from deep sleep randomly and very
often, somewhat depending on the card activity, maybe the hardware has a
floating wakeup pin or something. This was found by comparing two MS
Surface Book 2 devices, where one devices wifi card experienced spurious
wakeups, while the other one didn't.
Those continuous wakeups prevent the card from entering host sleep when
the computer suspends. And because the host won't answer to events from
the card anymore while it's suspended, the firmwares internal power
saving state machine seems to get confused and the card can't sleep
anymore at all after that.
Since we can't work around that hardware bug in the firmware, let's
get the hardware revision string from the firmware and match it with
known bad revisions. Then disable auto deep sleep for those revisions,
which makes sure we no longer get those spurious wakeups.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-3-verdre@v0yd.nl
Since the version string we get from the firmware is always 128
characters long, use a define for this size instead of having the number
128 copied all over the place.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-2-verdre@v0yd.nl
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
Attached is the panic report from fuzzing.
skbuff: skb_over_panic: text:000000003bf1b5fa
len:2048 put:4 head:00000000dd6a115b data:000000000a9445d8
tail:0x844 end:0x840 dev:<NULL>
kernel BUG at net/core/skbuff.c:109!
invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 PID: 198 Comm: in:imklog Not tainted 5.6.0 #60
RIP: 0010:skb_panic+0x15f/0x161
Call Trace:
<IRQ>
? mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
skb_put.cold+0x24/0x24
mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YX4CqjfRcTa6bVL+@Zekuns-MBP-16.fios-router.home
In following patches, dev_watchdog() will no longer stop all queues.
It will read queue->trans_start locklessly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: stable@vger.kernel.org # 3.5
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org
coccicheck complains about the use of snprintf() in sysfs show
functions:
WARNING use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211022090438.1065286-1-ye.guojin@zte.com.cn
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Convert wireless from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-3-kuba@kernel.org
When powersaving (so either wifi powersaving or deep sleep, depending on
which state the firmware is in) is disabled, the way the firmware goes
into host sleep is different: Usually the firmware implicitely enters
host sleep on the next SLEEP event we get when we configured host sleep
via HSCFG before. When powersaving is disabled though, there are no
SLEEP events, the way we enter host sleep in that case is different: The
firmware will send us a HS_ACT_REQ event and after that we "manually"
make the firmware enter host sleep by sending it another HSCFG command
with the action HS_ACTIVATE.
Now waking up from host sleep appears to be different depending on
whether powersaving is enabled again: When powersaving is enabled, the
firmware implicitely leaves host sleep as soon as it wakes up and sends
us an AWAKE event. When powersaving is disabled though, it apparently
doesn't implicitely leave host sleep, but instead we need to send it a
HSCFG command with the HS_CONFIGURE action and the HS_CFG_CANCEL
condition. We didn't do that so far, which is why waking up from host
sleep was broken when powersaving is disabled.
So add some additional state to mwifiex_adapter where we keep track of
whether host sleep was activated manually via HS_ACTIVATE, and if that
was the case, deactivate it manually again via HS_CFG_CANCEL.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-6-verdre@v0yd.nl
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
Sometimes the KEY_MATERIAL command can fail with the 88W8897 firmware
(when this happens exactly seems pretty random). This appears to prevent
the access point from starting, so it seems like a good idea to log an
error in that case.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-3-verdre@v0yd.nl
It's not an error if someone chooses to put their computer to sleep, not
wanting it to wake up because the person next door has just discovered
what a magic packet is. So change the loglevel of this annoying message
from ERROR to INFO.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-2-verdre@v0yd.nl
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr
clang complains about some NULL pointer arithmetic in this driver:
drivers/net/wireless/marvell/mwifiex/sta_tx.c:65:59: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
pad = ((void *)skb->data - (sizeof(*local_tx_pd) + hroom)-
^
drivers/net/wireless/marvell/mwifiex/uap_txrx.c:478:53: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
pad = ((void *)skb->data - (sizeof(*txpd) + hroom) - NULL) &
Rework that expression to do the same thing using a uintptr_t.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927121656.940304-1-arnd@kernel.org
The BSS priority here for a new P2P_CLIENT device was accidentally set
to an enum that's certainly not meant for this. Since
MWIFIEX_BSS_ROLE_STA is 0 anyway, we can just set the bss_priority to 0
instead here.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-10-verdre@v0yd.nl
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.
When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.
This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl
It's possible to change virtual interface type between P2P_CLIENT and
P2P_GO, the card supports that just fine, and it happens for example
when using miracast with the miraclecast software.
So allow type changes between P2P_CLIENT and P2P_GO and simply call into
mwifiex_change_vif_to_p2p(), which handles this just fine. We have to
call mwifiex_cfg80211_deinit_p2p() before though to make sure the old
p2p mode is properly uninitialized.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-7-verdre@v0yd.nl
In mwifiex_init_new_priv_params() we update our private driver state to
reflect the currently selected virtual interface type. Most notably we
set the bss_mode to the mode we're going to put the firmware in.
Now after we updated the driver state we actually start talking to the
firmware and instruct it to set up the new mode. Those commands can and
will sometimes fail, in which case we return with an error from
mwifiex_change_vif_to_*. We currently update our virtual interface type
counters after this return, which means the code is never reached when a
firmware error happens and we never update the counters. Since we have
updated our bss_mode earlier though, the counters now no longer reflect
the actual state of the driver.
This will break things on the next virtual interface change, because the
virtual interface type we're switching away from didn't get its counter
incremented, and we end up decrementing a 0-counter.
To fix this, simply update the virtual interface type counters right
after updating our driver structures, so that they are always in sync.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-6-verdre@v0yd.nl
Use a small helper function to increment and decrement the counter of
the interface types we currently manage. This makes the code that
actually changes and sets up the interface type a bit less messy and
also helps avoiding mistakes in case someone increments/decrements a
counter wrongly.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-5-verdre@v0yd.nl
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.
Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.
This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl
Instead of bailing out in the function which is supposed to do the type
change, detect invalid changes beforehand using a generic function and
return an error if the change is not allowed.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-3-verdre@v0yd.nl
Handle the obvious invalid virtual interface type changes with a general
check instead of looking at the individual change.
For type changes from P2P_CLIENT to P2P_GO and the other way round, this
changes the behavior slightly: We now still do nothing, but return
-EOPNOTSUPP instead of 0. Now that behavior was incorrect before and
still is, because type changes between these two types are actually
possible and supported, which we'll fix in a following commit.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-2-verdre@v0yd.nl
To reset mwifiex on Surface gen4+ (Pro 4 or later gen) devices, it
seems that putting the wifi device into D3cold is required according
to errata.inf file on Windows installation (Windows/INF/errata.inf).
This patch adds a function that performs power-cycle (put into D3cold
then D0) and call the function at the end of reset_prepare().
Note: Need to also reset the parent device (bridge) of wifi on SB1;
it might be because the bridge of wifi always reports it's in D3hot.
When I tried to reset only the wifi device (not touching parent), it gave
the following error and the reset failed:
acpi device:4b: Cannot transition to power state D0 for parent in D3hot
mwifiex_pcie 0000:03:00.0: can't change power state from D3cold to D0 (config space inaccessible)
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210820142050.35741-3-verdre@v0yd.nl
This commit adds the ability to apply device-specific quirks to the
mwifiex driver. It uses DMI matching similar to the quirks brcmfmac uses
with dmi.c. We'll add identifiers to match various MS Surface devices,
which this is primarily meant for, later.
This commit is a slightly modified version of a previous patch sent in
by Tsuchiya Yuto.
Co-developed-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210820142050.35741-2-verdre@v0yd.nl
Don't populate the arrays wpa_oui and wps_oui on the stack but
instead them static const. Makes the object code smaller by 63 bytes:
Before:
text data bss dec hex filename
29453 5451 64 34968 8898 .../wireless/marvell/mwifiex/sta_ioctl.o
After:
text data bss dec hex filename
29356 5611 64 35031 88d7 ../wireless/marvell/mwifiex/sta_ioctl.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819121651.7566-1-colin.king@canonical.com
There is no case in which the variable cmd_node->cmd_skb has no ->data,
and thus the variable host_cmd is guaranteed to be not NULL. Therefore,
the null-pointer check is redundant and can be dropped.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804020305.29812-1-islituo@gmail.com
The label is only used once, so we delete it and use the
return statement instead of the goto statement.
Signed-off-by: dingsenjie <dingsenjie@yulong.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210625121108.162868-1-dingsenjie@163.com
The get_unaligned()/put_unaligned() helpers are traditionally architecture
specific, with the two main variants being the "access-ok.h" version
that assumes unaligned pointer accesses always work on a particular
architecture, and the "le-struct.h" version that casts the data to a
byte aligned type before dereferencing, for architectures that cannot
always do unaligned accesses in hardware.
Based on the discussion linked below, it appears that the access-ok
version is not realiable on any architecture, but the struct version
probably has no downsides. This series changes the code to use the
same implementation on all architectures, addressing the few exceptions
separately.
Link: https://lore.kernel.org/lkml/75d07691-1e4f-741f-9852-38c0b4f520bc@synopsys.com/
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363
Link: https://lore.kernel.org/lkml/20210507220813.365382-14-arnd@kernel.org/
Link: git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic.git unaligned-rework-v2
Link: https://lore.kernel.org/lkml/CAHk-=whGObOKruA_bU3aPGZfoDqZM1_9wBkwREp0H0FgR-90uQ@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=IY5U
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-unaligned-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm/unaligned.h unification from Arnd Bergmann:
"Unify asm/unaligned.h around struct helper
The get_unaligned()/put_unaligned() helpers are traditionally
architecture specific, with the two main variants being the
"access-ok.h" version that assumes unaligned pointer accesses always
work on a particular architecture, and the "le-struct.h" version that
casts the data to a byte aligned type before dereferencing, for
architectures that cannot always do unaligned accesses in hardware.
Based on the discussion linked below, it appears that the access-ok
version is not realiable on any architecture, but the struct version
probably has no downsides. This series changes the code to use the
same implementation on all architectures, addressing the few
exceptions separately"
Link: https://lore.kernel.org/lkml/75d07691-1e4f-741f-9852-38c0b4f520bc@synopsys.com/
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363
Link: https://lore.kernel.org/lkml/20210507220813.365382-14-arnd@kernel.org/
Link: git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic.git unaligned-rework-v2
Link: https://lore.kernel.org/lkml/CAHk-=whGObOKruA_bU3aPGZfoDqZM1_9wBkwREp0H0FgR-90uQ@mail.gmail.com/
* tag 'asm-generic-unaligned-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: simplify asm/unaligned.h
asm-generic: uaccess: 1-byte access is always aligned
netpoll: avoid put_unaligned() on single character
mwifiex: re-fix for unaligned accesses
apparmor: use get_unaligned() only for multi-byte words
partitions: msdos: fix one-byte get_unaligned()
asm-generic: unaligned always use struct helpers
asm-generic: unaligned: remove byteshift helpers
powerpc: use linux/unaligned/le_struct.h on LE power7
m68k: select CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
sh: remove unaligned access for sh4a
openrisc: always use unaligned-struct header
asm-generic: use asm-generic/unaligned.h for most architectures
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring array fields.
When preparing to call mwifiex_set_keyparamset_wep(), key_material is
treated very differently from its structure layout (which has only a
single struct mwifiex_ie_type_key_param_set). Instead, add a new type to
the union so memset() can correctly reason about the size of the
structure.
Note that the union ("params", 196 bytes) containing key_material was
not large enough to hold the target of this memset(): sizeof(struct
mwifiex_ie_type_key_param_set) == 60, NUM_WEP_KEYS = 4, so 240
bytes, or 44 bytes past the end of "params". The good news is that
it appears that the command buffer, as allocated, is 2048 bytes
(MWIFIEX_SIZE_OF_CMD_BUFFER), so no neighboring memory appears to be
getting clobbered.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210617171522.3410951-1-keescook@chromium.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields. Use the
sub-structure address directly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210617041431.2168953-1-keescook@chromium.org
Only one important fix for an mwifiex regression.
mwifiex
* fix deadlock during rmmod or firmware reset, regression from
cfg80211 RTNL changes in v5.12-rc1
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmDOEp8VHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622bnqgIAI0PL/+2jNY6q6aJ8QK0PEYThDJH
CoWwb5JktkbqNq1nco/c7EqEKPq8TLyP3/SGhfZuiPcp2J+OlztHP3dMbQzm9du8
6rDGf/g7ZVY20GHr1rtZDNnRct054Vx/I1UMF4vMZdk2BCXrkycgvCfK5Rqg/2RU
5pA5c9/ZOguWDAbOEMAP+/G6bHFlpy1nasT5jNuYswjZJ28zgkWJKRi1QQFoe5Qn
y8TYGNCdwI4Jf93zTiiH5sJ9sFqjpMz04L9nMoEzCodgMKXAnMmqr0YjcWqxpagt
DeU80Bo189pw7CkeOEPhC75l2LM/N6llFINAAD69miPQGiyzJGZwUtxhMPE=
=rpHP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2021-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.13
Only one important fix for an mwifiex regression.
mwifiex
* fix deadlock during rmmod or firmware reset, regression from
cfg80211 RTNL changes in v5.12-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_RW helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210523040339.2724-1-yuehaibing@huawei.com
There are a few leading spaces before tabs and remove it by running the
following commard:
$ find . -name '*.c' | xargs sed -r -i 's/^[ ]+\t/\t/'
$ find . -name '*.h' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1621407345-10625-2-git-send-email-tanghui20@huawei.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/if_usb.c:56: warning: expecting prototype for if_usb_wrike_bulk_callback(). Prototype was for if_usb_write_bulk_callback() instead
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210517050141.61488-8-shenyang39@huawei.com
We can deadlock when rmmod'ing the driver or going through firmware
reset, because the cfg80211_unregister_wdev() has to bring down the link
for us, ... which then grab the same wiphy lock.
nl80211_del_interface() already handles a very similar case, with a nice
description:
/*
* We hold RTNL, so this is safe, without RTNL opencount cannot
* reach 0, and thus the rdev cannot be deleted.
*
* We need to do it for the dev_close(), since that will call
* the netdev notifiers, and we need to acquire the mutex there
* but don't know if we get there from here or from some other
* place (e.g. "ip link set ... down").
*/
mutex_unlock(&rdev->wiphy.mtx);
...
Do similarly for mwifiex teardown, by ensuring we bring the link down
first.
Sample deadlock trace:
[ 247.103516] INFO: task rmmod:2119 blocked for more than 123 seconds.
[ 247.110630] Not tainted 5.12.4 #5
[ 247.115796] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 247.124557] task:rmmod state:D stack: 0 pid: 2119 ppid: 2114 flags:0x00400208
[ 247.133905] Call trace:
[ 247.136644] __switch_to+0x130/0x170
[ 247.140643] __schedule+0x714/0xa0c
[ 247.144548] schedule_preempt_disabled+0x88/0xf4
[ 247.149714] __mutex_lock_common+0x43c/0x750
[ 247.154496] mutex_lock_nested+0x5c/0x68
[ 247.158884] cfg80211_netdev_notifier_call+0x280/0x4e0 [cfg80211]
[ 247.165769] raw_notifier_call_chain+0x4c/0x78
[ 247.170742] call_netdevice_notifiers_info+0x68/0xa4
[ 247.176305] __dev_close_many+0x7c/0x138
[ 247.180693] dev_close_many+0x7c/0x10c
[ 247.184893] unregister_netdevice_many+0xfc/0x654
[ 247.190158] unregister_netdevice_queue+0xb4/0xe0
[ 247.195424] _cfg80211_unregister_wdev+0xa4/0x204 [cfg80211]
[ 247.201816] cfg80211_unregister_wdev+0x20/0x2c [cfg80211]
[ 247.208016] mwifiex_del_virtual_intf+0xc8/0x188 [mwifiex]
[ 247.214174] mwifiex_uninit_sw+0x158/0x1b0 [mwifiex]
[ 247.219747] mwifiex_remove_card+0x38/0xa0 [mwifiex]
[ 247.225316] mwifiex_pcie_remove+0xd0/0xe0 [mwifiex_pcie]
[ 247.231451] pci_device_remove+0x50/0xe0
[ 247.235849] device_release_driver_internal+0x110/0x1b0
[ 247.241701] driver_detach+0x5c/0x9c
[ 247.245704] bus_remove_driver+0x84/0xb8
[ 247.250095] driver_unregister+0x3c/0x60
[ 247.254486] pci_unregister_driver+0x2c/0x90
[ 247.259267] cleanup_module+0x18/0xcdc [mwifiex_pcie]
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-wireless/98392296-40ee-6300-369c-32e16cff3725@gmail.com/
Link: https://lore.kernel.org/linux-wireless/ab4d00ce52f32bd8e45ad0448a44737e@bewaar.me/
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Reported-by: dave@bewaar.me
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Dave Olsthoorn <dave@bewaar.me>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210515024227.2159311-1-briannorris@chromium.org
A patch from 2017 changed some accesses to DMA memory to use
get_unaligned_le32() and similar interfaces, to avoid problems
with doing unaligned accesson uncached memory.
However, the change in the mwifiex_pcie_alloc_sleep_cookie_buf()
function ended up changing the size of the access instead,
as it operates on a pointer to u8.
Change this function back to actually access the entire 32 bits.
Note that the pointer is aligned by definition because it came
from dma_alloc_coherent().
Fixes: 92c70a958b ("mwifiex: fix for unaligned reads")
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The libertas driver was trying to register sysfs groups "by hand" which
causes them to be created _after_ the device is initialized and
announced to userspace, which causes races and can prevent userspace
tools from seeing the sysfs files correctly.
Fix this up by using the built-in sysfs_groups pointers in struct
net_device which were created for this very reason, fixing the race
condition, and properly allowing for any error that might have occured
to be handled properly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-54-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 434256833d.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit was incorrect, the error needs to be propagated back
to the caller AND if the second group call fails, the first needs to be
removed. There are much better ways to solve this, the driver should
NOT be calling sysfs_create_group() on its own as it is racing userspace
and loosing.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-53-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
Fixes: a66098daac ("mwl8k: Marvell TOPDOG wireless driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402182627.4256-1-lyl2019@mail.ustc.edu.cn
Building without mesh supports shows a couple of warnings with
'make W=1':
drivers/net/wireless/marvell/libertas/main.c: In function 'lbs_start_card':
drivers/net/wireless/marvell/libertas/main.c:1068:37: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
1068 | lbs_start_mesh(priv);
Change the macros to use the usual "do { } while (0)" instead to shut up
the warnings and make the code a litte more robust.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210322104343.948660-4-arnd@kernel.org
There are a few reasons not to dump SSIDs as-is in kernel logs:
1) they're not guaranteed to be any particular text encoding (UTF-8,
ASCII, ...) in general
2) it's somewhat redundant; the BSSID should be enough to uniquely
identify the AP/STA to which we're connecting
3) BSSIDs have an easily-recognized format, whereas SSIDs do not (they
are free-form)
4) other common drivers (e.g., everything based on mac80211) get along
just fine by only including BSSIDs when logging state transitions
Additional notes on reason #3: this is important for the
privacy-conscious, especially when providing tools that convey
kernel logs on behalf of a user -- e.g., when reporting bugs. So for
example, it's easy to automatically filter logs for MAC addresses, but
it's much harder to filter SSIDs out of unstructured text.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210225024454.4106485-1-briannorris@chromium.org
sturct mwl8k_dma_data contains a ieee80211_hdr structure, which is required to
have at least two byte alignment, and this conflicts with the __packed
attribute:
vers/net/wireless/marvell/mwl8k.c:811:1: warning: alignment 1 of 'struct mwl8k_dma_data' is less than 2 [-Wpacked-not-aligned]
Mark mwl8k_dma_data itself as having two-byte alignment to ensure the
inner structure is properly aligned.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210204162813.3159319-1-arnd@kernel.org
When a network is moved or reconfigured on the different channel, there
can be multiple BSSes with the same BSSID and SSID in scan result
before the old one expires. Then, it can cause cfg80211_connect_result
to map current_bss to a bss with the wrong channel.
Let mwifiex_cfg80211_assoc return the selected BSS and then the caller
can report it cfg80211_connect_bss.
Signed-off-by: Yen-lin Lai <yenlinlai@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210201070649.1667209-1-yenlinlai@chromium.org
The variable ret is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210128162202.642848-1-colin.king@canonical.com
First set of patches for v5.12. A smaller pull request this time,
biggest feature being a better key handling for ath9k. And of course
the usual fixes and cleanups all over.
Major changes:
ath9k
* more robust encryption key cache management
brcmfmac
* support BCM4365E with 43666 ChipCommon chip ID
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJgHW7nAAoJEG4XJFUm622bgd0IAKtEBcjfqnR2wW7Rt6Ah/Uch
vInrZ+5YOhjamoCvZHhTwdvUEmuRYJBT8ZqfO5x3X0GlIaJe1PlJhlvOs/9PkQ9G
eMSFcy1D/uSb3KoRRLq8lNaAy7NAyajg11IhRAeQFLeBkZgI43PGq6j7sbYCerah
87trNNlHagio9p4q9FGXVtJ2cJGQdNHM8jn4dw5Uue45YArkhj6VBh3EZl9dqV+F
XmxK+qvIcK1KPzw6nZ/0dGf8B6dnXaljn0cAzAo8QPSaZI+jozY52y3XdoKVqYRF
ekqDra4Xl/uKVZR1vb2jE5T/NtmzZI63uifndL6esEjwJMrrkRy9+alHwIxt2rU=
=KZD7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.12
First set of patches for v5.12. A smaller pull request this time,
biggest feature being a better key handling for ath9k. And of course
the usual fixes and cleanups all over.
Major changes:
ath9k
* more robust encryption key cache management
brcmfmac
* support BCM4365E with 43666 ChipCommon chip ID
* tag 'wireless-drivers-next-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (35 commits)
iwl4965: do not process non-QOS frames on txq->sched_retry path
mt7601u: process tx URBs with status EPROTO properly
wlcore: Fix command execute failure 19 for wl12xx
mt7601u: use ieee80211_rx_list to pass frames to the network stack as a batch
rtw88: 8723de: adjust the LTR setting
rtlwifi: rtl8821ae: fix bool comparison in expressions
rtlwifi: rtl8192se: fix bool comparison in expressions
rtlwifi: rtl8188ee: fix bool comparison in expressions
rtlwifi: rtl8192c-common: fix bool comparison in expressions
rtlwifi: rtl_pci: fix bool comparison in expressions
wlcore: Downgrade exceeded max RX BA sessions to debug
wilc1000: use flexible-array member instead of zero-length array
brcmfmac: clear EAP/association status bits on linkdown events
brcmfmac: Delete useless kfree code
qtnfmac_pcie: Use module_pci_driver
mt7601u: check the status of device in calibration
mt7601u: process URBs in status EPROTO properly
brcmfmac: support BCM4365E with 43666 ChipCommon chip ID
wilc1000: fix spelling mistake in Kconfig "devision" -> "division"
mwifiex: pcie: Drop bogus __refdata annotation
...
====================
Link: https://lore.kernel.org/r/20210205161901.C7F83C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We used to not require anything in terms of registering netdevs
with cfg80211, using a netdev notifier instead. However, in the
next patch reducing RTNL locking, this causes big problems, and
the simplest way is to just require drivers to do things better.
Change the registration/unregistration semantics to require the
drivers to call cfg80211_(un)register_netdevice() when this is
happening due to a cfg80211 request, i.e. add_virtual_intf() or
del_virtual_intf() (or if it somehow has to happen in any other
cfg80211 callback).
Otherwise, in other contexts, drivers may continue to use the
normal netdev (un)registration functions as usual.
Internally, we still use the netdev notifier and track (by the
new wdev->registered bool) if the wdev had already been added
to cfg80211 or not.
Link: https://lore.kernel.org/r/20210122161942.cf2f4b65e4e9.Ida8234e50da13eb675b557bac52a713ad4eddf71@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the Marvell PCIE WiFi-Ex driver does not have any code or data
located in initmem, there is no need to annotate the mwifiex_pcie
structure with __refdata. Drop the annotation, to avoid suppressing
future section warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201211133835.2970384-1-geert+renesas@glider.be
mwifiex_cmd_802_11_ad_hoc_start() calls memcpy() without checking
the destination size may trigger a buffer overflower,
which a local user could use to cause denial of service
or the execution of arbitrary code.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Zhang Xiaohui <ruc_zhangxiaohui@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201206084801.26479-1-ruc_zhangxiaohui@163.com
As of 6-DEC-2019, NXP has acquired Marvell’s Wireless business
unit. This change is to update the license text accordingly.
commit 932183aa35 ("mwifiex: change license text from MARVELL
to NXP") does this, but it left out two files.
Signed-off-by: James Cao <zheng.cao@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606814307-32715-1-git-send-email-ganapathi.bhat@nxp.com
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201117160958.GA18807@embeddedor
If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().
# firmware went into a bad state
[...]
[ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
[ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
[ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
[ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
# reset performed after firmware went into a bad state
[ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
[ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
# but even the reset failed
[ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
[ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
[ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
[ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
[ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
[ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
[ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
[ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
[ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
[ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
[ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
[ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
[ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
[ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
[ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
# mwifiex_pcie_work hang happening
[ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
[ 1823.233932] Tainted: G WC OE 5.10.0-rc1-1-mainline #1
[ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1823.233940] task:kworker/3:1 state:D stack: 0 pid: 44 ppid: 2 flags:0x00004000
[ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
[ 1823.233965] Call Trace:
[ 1823.233981] __schedule+0x292/0x820
[ 1823.233990] schedule+0x45/0xe0
[ 1823.233995] schedule_timeout+0x11c/0x160
[ 1823.234003] wait_for_completion+0x9e/0x100
[ 1823.234012] __flush_work.isra.0+0x156/0x210
[ 1823.234018] ? flush_workqueue_prep_pwqs+0x130/0x130
[ 1823.234026] __cancel_work_timer+0x11e/0x1a0
[ 1823.234035] mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
[ 1823.234049] mwifiex_free_adapter+0x24/0xe0 [mwifiex]
[ 1823.234060] _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
[ 1823.234074] mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
[ 1823.234080] mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
[ 1823.234087] pci_try_reset_function+0x5c/0x90
[ 1823.234094] process_one_work+0x1d6/0x3a0
[ 1823.234100] worker_thread+0x4d/0x3d0
[ 1823.234107] ? rescuer_thread+0x410/0x410
[ 1823.234112] kthread+0x142/0x160
[ 1823.234117] ? __kthread_bind_mask+0x60/0x60
[ 1823.234124] ret_from_fork+0x22/0x30
[...]
This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():
- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().
The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().
Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.
This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.
After this commit, when reset fails, the following output is
expected to be shown:
kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
kernel: mwifiex: Failed to bring up adapter: -5
kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5
To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).
# put into D3 (root port)
sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com
The functions mwifiex_shutdown_sw() and mwifiex_reinit_sw() can be used
for more general purposes than the PCIe function level reset. Also, these
are even not PCIe-specific.
So, let's update the comments at the top of each function accordingly.
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142110.18144-3-kitakar@gmail.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/mwifiex/pcie.c: In function ‘mwifiex_pcie_remove’:
drivers/net/wireless/marvell/mwifiex/pcie.c:432:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/marvell/mwifiex/pcie.c: In function ‘mwifiex_cleanup_pcie’:
drivers/net/wireless/marvell/mwifiex/pcie.c:3142:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-32-lee.jones@linaro.org
clang static analysis reports this problem:
sdio.c:2403:3: warning: Attempt to free released memory
kfree(card->mpa_rx.buf);
^~~~~~~~~~~~~~~~~~~~~~~
When mwifiex_init_sdio() fails in its first call to
mwifiex_alloc_sdio_mpa_buffer, it falls back to calling it
again. If the second alloc of mpa_tx.buf fails, the error
handler will try to free the old, previously freed mpa_rx.buf.
Reviewing the code, it looks like a second double free would
happen with mwifiex_cleanup_sdio().
So set both pointers to NULL when they are freed.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004131931.29782-1-trix@redhat.com
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
libertas uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug macro prints (INT) when in_interrupt() returns true. The value of
this information is dubious as it does not distinguish between the various
contexts which are covered by in_interrupt().
As the usage of in_interrupt() in drivers is phased out and the same
information can be more precisely obtained with tracing, remove the
in_interrupt() conditional from this debug printk.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
mwifiex uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
clang static analyzer reports this problem
init.c:739:8: warning: Called function pointer
is null (null dereference)
ret = adapter->if_ops.check_fw_status( ...
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In mwifiex_dnld_fw, there is an earlier check for check_fw_status(),
The check was introduced for usb support at the same time this
check in _mwifiex_fw_dpc() was made
if (adapter->if_ops.dnld_fw) {
ret = adapter->if_ops.dnld_fw(adapter, &fw);
} else {
ret = mwifiex_dnld_fw(adapter, &fw);
}
And a dnld_fw function initialized as part the usb's
mwifiex_if_ops.
The other instances of mwifiex_if_ops for pci and sdio
both set check_fw_status.
So the first check is not needed and can be removed.
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906200548.18053-1-trix@redhat.com
These variables only used in sdio.c, move them to .c file
can silence these warnings:
In file included from drivers/net/wireless/marvell/mwifiex//main.h:59:0,
from drivers/net/wireless/marvell/mwifiex//cfp.c:24:
drivers/net/wireless/marvell/mwifiex//sdio.h:705:41: warning: ‘mwifiex_sdio_sd8801’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8801 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:689:41: warning: ‘mwifiex_sdio_sd8987’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8987 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:674:41: warning: ‘mwifiex_sdio_sd8887’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8887 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:658:41: warning: ‘mwifiex_sdio_sd8997’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8997 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:642:41: warning: ‘mwifiex_sdio_sd8977’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8977 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:627:41: warning: ‘mwifiex_sdio_sd8897’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8897 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:612:41: warning: ‘mwifiex_sdio_sd8797’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8797 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:597:41: warning: ‘mwifiex_sdio_sd8787’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8787 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:582:41: warning: ‘mwifiex_sdio_sd8786’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8786 = {
^~~~~~~~~~~~~~~~~~~
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902141155.30144-1-yuehaibing@huawei.com
In file included from drivers/net/wireless/marvell/mwifiex//cmdevt.c:26:0:
drivers/net/wireless/marvell/mwifiex//wmm.h:41:17: warning: ‘tos_to_tid_inv’ defined but not used [-Wunused-const-variable=]
static const u8 tos_to_tid_inv[] = {
^~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//wmm.h:34:18: warning: ‘mwifiex_1d_to_wmm_queue’ defined but not used [-Wunused-const-variable=]
static const u16 mwifiex_1d_to_wmm_queue[8] = { 1, 0, 0, 1, 2, 2, 3, 3 };
^~~~~~~~~~~~~~~~~~~~~~~
move the variables definition to .c file, and leave declarations
in the header file to fix these warnings.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902140846.29024-1-yuehaibing@huawei.com
A new warning in clang points out when macro expansion might result in a
GNU C statement expression. There is an instance of this in the mwifiex
driver:
drivers/net/wireless/marvell/mwifiex/cmdevt.c:217:34: warning: '}' and
')' tokens terminating statement expression appear in different macro
expansion contexts [-Wcompound-token-split-by-macro]
host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/fw.h:519:46: note: expanded from
macro 'HostCmd_SET_SEQ_NO_BSS_INFO'
(((type) & 0x000f) << 12); }
^
This does not appear to be a real issue. Removing the braces and
replacing them with parentheses will fix the warning and not change the
meaning of the code.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1146
Reported-by: Andy Lavr <andy.lavr@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200901070834.1015754-1-natechancellor@gmail.com
Saves on 10's of complains about 'defined but not used' variables.
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/marvell/mwifiex/main.h:57,
from drivers/net/wireless/marvell/mwifiex/main.c:22:
drivers/net/wireless/marvell/mwifiex/pcie.h:310:41: warning: ‘mwifiex_pcie8997’ defined but not used [-Wunused-const-variable=]
310 | static const struct mwifiex_pcie_device mwifiex_pcie8997 = {
| ^~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/pcie.h:300:41: warning: ‘mwifiex_pcie8897’ defined but not used [-Wunused-const-variable=]
300 | static const struct mwifiex_pcie_device mwifiex_pcie8897 = {
| ^~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/pcie.h:292:41: warning: ‘mwifiex_pcie8766’ defined but not used [-Wunused-const-variable=]
292 | static const struct mwifiex_pcie_device mwifiex_pcie8766 = {
| ^~~~~~~~~~~~~~~~
NB: Repeats 10's of times - snipped for brevity.
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-2-lee.jones@linaro.org
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/if_usb.c:56: warning: Function parameter or member 'urb' not described in 'if_usb_write_bulk_callback'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:73: warning: Function parameter or member 'cardp' not described in 'if_usb_free'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:146: warning: Function parameter or member 'intf' not described in 'if_usb_probe'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:146: warning: Function parameter or member 'id' not described in 'if_usb_probe'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:244: warning: Function parameter or member 'intf' not described in 'if_usb_disconnect'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:272: warning: Function parameter or member 'cardp' not described in 'if_usb_send_fw_pkt'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'cardp' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'payload' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'nb' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'data' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:625: warning: Function parameter or member 'urb' not described in 'if_usb_receive'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'priv' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'type' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'payload' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'nb' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:742: warning: Function parameter or member 'cardp' not described in 'if_usb_issue_boot_command'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:742: warning: Function parameter or member 'ivalue' not described in 'if_usb_issue_boot_command'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:766: warning: Function parameter or member 'data' not described in 'check_fwfile_format'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:766: warning: Function parameter or member 'totlen' not described in 'check_fwfile_format'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-28-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas/firmware.c:134: warning: Function parameter or member 'device' not described in 'lbs_get_firmware_async'
drivers/net/wireless/marvell/libertas/firmware.c:134: warning: Excess function parameter 'dev' description in 'lbs_get_firmware_async'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-27-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas/main.c:727: warning: Function parameter or member 't' not described in 'lbs_cmd_timeout_handler'
drivers/net/wireless/marvell/libertas/main.c:727: warning: Excess function parameter 'data' description in 'lbs_cmd_timeout_handler'
drivers/net/wireless/marvell/libertas/main.c:761: warning: Function parameter or member 't' not described in 'lbs_tx_lockup_handler'
drivers/net/wireless/marvell/libertas/main.c:761: warning: Excess function parameter 'data' description in 'lbs_tx_lockup_handler'
drivers/net/wireless/marvell/libertas/main.c:784: warning: Function parameter or member 't' not described in 'auto_deepsleep_timer_fn'
drivers/net/wireless/marvell/libertas/main.c:784: warning: Excess function parameter 'data' description in 'auto_deepsleep_timer_fn'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-15-lee.jones@linaro.org
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Also demote one stray non-kernel-doc header.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/cmd.c:44: warning: Function parameter or member 'priv' not described in 'lbtf_cmd_copyback'
drivers/net/wireless/marvell/libertas_tf/cmd.c:44: warning: Function parameter or member 'extra' not described in 'lbtf_cmd_copyback'
drivers/net/wireless/marvell/libertas_tf/cmd.c:44: warning: Function parameter or member 'resp' not described in 'lbtf_cmd_copyback'
drivers/net/wireless/marvell/libertas_tf/cmd.c:80: warning: Function parameter or member 'priv' not described in 'lbtf_update_hw_spec'
drivers/net/wireless/marvell/libertas_tf/cmd.c:150: warning: Function parameter or member 'priv' not described in 'lbtf_set_channel'
drivers/net/wireless/marvell/libertas_tf/cmd.c:150: warning: Function parameter or member 'channel' not described in 'lbtf_set_channel'
drivers/net/wireless/marvell/libertas_tf/cmd.c:277: warning: Function parameter or member 'priv' not described in '__lbtf_cleanup_and_insert_cmd'
drivers/net/wireless/marvell/libertas_tf/cmd.c:277: warning: Function parameter or member 'cmdnode' not described in '__lbtf_cleanup_and_insert_cmd'
drivers/net/wireless/marvell/libertas_tf/cmd.c:442: warning: Function parameter or member 'priv' not described in 'lbtf_allocate_cmd_buffer'
drivers/net/wireless/marvell/libertas_tf/cmd.c:490: warning: Function parameter or member 'priv' not described in 'lbtf_free_cmd_buffer'
drivers/net/wireless/marvell/libertas_tf/cmd.c:527: warning: Function parameter or member 'priv' not described in 'lbtf_get_cmd_ctrl_node'
drivers/net/wireless/marvell/libertas_tf/cmd.c:561: warning: Function parameter or member 'priv' not described in 'lbtf_execute_next_command'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-8-lee.jones@linaro.org
There are only 2 kernel-doc headers in this file and both are
incorrect. The first one does not attempt to document the function at
all and the second one is suffering from severe doc-rot; the format is
wrong and only 1 out of 3 parameters are being documented.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/main.c:129: warning: Function parameter or member 't' not described in 'command_timer_fn'
drivers/net/wireless/marvell/libertas_tf/main.c:554: warning: Function parameter or member 'card' not described in 'lbtf_add_card'
drivers/net/wireless/marvell/libertas_tf/main.c:554: warning: Function parameter or member 'dmdev' not described in 'lbtf_add_card'
drivers/net/wireless/marvell/libertas_tf/main.c:554: warning: Function parameter or member 'ops' not described in 'lbtf_add_card'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-5-lee.jones@linaro.org
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-12-allen.cryptic@gmail.com
Following commit e186967865 ("mwifiex: Prevent memory corruption
handling keys") the mwifiex driver fails to authenticate with certain
networks, specifically networks with 256 bit keys, and repeatedly asks
for the password. The kernel log repeats the following lines (id and
bssid redacted):
mwifiex_pcie 0000:01:00.0: info: trying to associate to '<id>' bssid <bssid>
mwifiex_pcie 0000:01:00.0: info: associated to bssid <bssid> successfully
mwifiex_pcie 0000:01:00.0: crypto keys added
mwifiex_pcie 0000:01:00.0: info: successfully disconnected from <bssid>: reason code 3
Tracking down this problem lead to the overflow check introduced by the
aforementioned commit into mwifiex_ret_802_11_key_material_v2(). This
check fails on networks with 256 bit keys due to the current storage
size for AES keys in struct mwifiex_aes_param being only 128 bit.
To fix this issue, increase the storage size for AES keys to 256 bit.
Fixes: e186967865 ("mwifiex: Prevent memory corruption handling keys")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reported-by: Kaloyan Nikolov <konik98@gmail.com>
Tested-by: Kaloyan Nikolov <konik98@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200825153829.38043-1-luzmaximilian@gmail.com
syzbot is reporting that del_timer_sync() is called from
mwifiex_usb_cleanup_tx_aggr() from mwifiex_unregister_dev() without
checking timer_setup() from mwifiex_usb_tx_init() was called [1].
Ganapathi Bhat proposed a possibly cleaner fix, but it seems that
that fix was forgotten [2].
"grep -FrB1 'del_timer' drivers/ | grep -FA1 '.function)'" says that
currently there are 28 locations which call del_timer[_sync]() only if
that timer's function field was initialized (because timer_setup() sets
that timer's function field). Therefore, let's use same approach here.
[1] https://syzkaller.appspot.com/bug?id=26525f643f454dd7be0078423e3cdb0d57744959
[2] https://lkml.kernel.org/r/CA+ASDXMHt2gq9Hy+iP_BYkWXsSreWdp3_bAfMkNcuqJ3K+-jbQ@mail.gmail.com
Reported-by: syzbot <syzbot+dc4127f950da51639216@syzkaller.appspotmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821082720.7716-1-penguin-kernel@I-love.SAKURA.ne.jp
The error message if 'pci_set_consistent_dma_mask()' fails is misleading.
The function call uses 32 bits, but the error message reports 64.
Moreover, according to the comment above 'dma_set_mask_and_coherent()'
definition, such an error can never happen.
So, simplify code, axe the misleading message and use
'dma_set_mask_and_coherent()' instead of 'dma_set_mask()' +
'dma_set_coherent_mask()'
While at it, make some clean-up:
- add # when reporting allocated length to be consistent between
functions
- s/consistent/coherent/
- s/unsigned int/u32/ to be consistent between functions
- align some code
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819071853.113185-1-christophe.jaillet@wanadoo.fr
A possible call chain is as follow:
mwifiex_sdio_interrupt (sdio.c)
--> mwifiex_main_process (main.c)
--> mwifiex_process_cmdresp (cmdevt.c)
--> mwifiex_process_sta_cmdresp (sta_cmdresp.c)
--> mwifiex_ret_802_11_scan (scan.c)
--> mwifiex_parse_single_response_buf (scan.c)
'mwifiex_sdio_interrupt()' is an interrupt function.
Also note that 'mwifiex_ret_802_11_scan()' already uses GFP_ATOMIC.
So use GFP_ATOMIC instead of GFP_KERNEL when memory is allocated in
'mwifiex_parse_single_response_buf()'.
Fixes: 7c6fa2a843 ("mwifiex: use cfg80211 dynamic scan table and cfg80211_get_bss API")
or
Fixes: 601216e12c ("mwifiex: process RX packets in SDIO IRQ thread directly")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200809092906.744621-1-christophe.jaillet@wanadoo.fr
Second set of patches for v5.9. mt76 has most of patches this time.
Otherwise it's just smaller fixes and cleanups to other drivers.
There was a major conflict in mt76 driver between wireless-drivers and
wireless-drivers-next. I solved that by merging the former to the
latter.
Major changes:
rtw88
* add support for ieee80211_ops::change_interface
* add support for enabling and disabling beacon
* add debugfs file for testing h2c
mt76
* ARP filter offload for 7663
* runtime power management for 7663
* testmode support for mfg calibration
* support for more channels
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfKUIHAAoJEG4XJFUm622bXqkH/jgjKWh4b96Pv56jLPtyoPKj
q9ZvIS1MFhfeY/DFX2gAx34iOwDi7lRVsb1r8IX+rui+B4yTDkvgM2azduSfUpA7
+WOHaQdRYMbUa0YlvotaxFaHpqABKFnRd3zQKTMgT3LyVgj6OMiyHhc7DJTrBvMM
KR+Z6/aNmMccWcSR4OPPF8zPRmp7h5yLW55UgqfOm0JzRfCnXtq6vb6MUDxYelGm
ruvKP2W86m0DfQzPSwCEdSPkD/2aspi9HrMJNXm/cNqGk6AFQTZzPpQC6PowSrWA
9rpzBRti2OwDD6Q6QJqmWzQ8pclP4BMZWPyYBqaC8tTHDvD13OV/siZVk9nP+As=
=KOz+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.9
Second set of patches for v5.9. mt76 has most of patches this time.
Otherwise it's just smaller fixes and cleanups to other drivers.
There was a major conflict in mt76 driver between wireless-drivers and
wireless-drivers-next. I solved that by merging the former to the
latter.
Major changes:
rtw88
* add support for ieee80211_ops::change_interface
* add support for enabling and disabling beacon
* add debugfs file for testing h2c
mt76
* ARP filter offload for 7663
* runtime power management for 7663
* testmode support for mfg calibration
* support for more channels
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-07-31
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The length of the key comes from the network and it's a 16 bit number. It
needs to be capped to prevent a buffer overflow.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200708115857.GA13729@mwanda
ENOTSUPP (double PP) is internal linux kernel code 524 available only in
kernel include file linux/errno.h and not exported to userspace.
EOPNOTSUPP (OP; double PP) is standard code 95 for reporting 'operation not
supported' available via kernel include file uapi/asm-generic/errno.h.
ENOTSUP (single P) is alias for EOPNOTSUPP defined only in userspace
include file bits/errno.h and not available in kernel.
Because Linux kernel does not support ENOTSUP (single P) and because
userspace does not support ENOTSUPP (double PP), report error code for
'operation not supported' via EOPNOTSUPP macro.
This patch fixes problem that mwifiex kernel driver sends to userspace
unsupported error codes like: "failed: -524 (No error information)".
After applying this patch userspace see: "failed: -95 (Not supported)".
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200703112151.18917-1-pali@kernel.org
This macro is already used in mwifiex driver for specifying upper limit and
is defined to value 3. So use it also in struct ieee80211_iface_limit.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200626152938.12737-1-pali@kernel.org
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Firmware for sd8997 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8997_combo_v4.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8997.
Fixes: 6d85ef00d9 ("mwifiex: add support for 8997 chipset")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware for sd8977 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8977_combo_v2.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8977.
Fixes: 1a0f547831 ("mwifiex: add support for sd8977 chipset")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
SD8997 firmware sends TLV_TYPE_MAX_CONN with struct hw_spec_max_conn to
inform kernel about maximum number of p2p connections and stations in AP
mode.
During initialization of SD8997 wifi chip kernel prints warning:
mwifiex_sdio mmc0:0001:1: Unknown GET_HW_SPEC TLV type: 0x217
This patch adds support for parsing TLV_TYPE_MAX_CONN (0x217) and sets
appropriate cfg80211 member 'max_ap_assoc_sta' from retrieved structure.
It allows userspace to retrieve NL80211_ATTR_MAX_AP_ASSOC_STA attribute.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123559.29028-1-pali@kernel.org
During initialization of SD8997 wifi chip kernel prints warnings:
mwifiex_sdio mmc0:0001:1: Unknown api_id: 3
mwifiex_sdio mmc0:0001:1: Unknown api_id: 4
This patch adds support for parsing all api ids provided by SD8997
firmware.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123444.28957-1-pali@kernel.org
Add _WLAN suffix to macro names for consistency with other Marvell macros.
These IDs represents wlan function of combo bt/wlan cards. Other functions
of these cards have different IDs.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-4-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mwifiex_cfg80211_dump_station() uses static variable for iterating
over a linked list of all associated stations (when the driver is in UAP
role). This has a race condition if .dump_station is called in parallel
for multiple interfaces. This corruption can be triggered by registering
multiple SSIDs and calling, in parallel for multiple interfaces
iw dev <iface> station dump
[16750.719775] Unable to handle kernel paging request at virtual address dead000000000110
...
[16750.899173] Call trace:
[16750.901696] mwifiex_cfg80211_dump_station+0x94/0x100 [mwifiex]
[16750.907824] nl80211_dump_station+0xbc/0x278 [cfg80211]
[16750.913160] netlink_dump+0xe8/0x320
[16750.916827] netlink_recvmsg+0x1b4/0x338
[16750.920861] ____sys_recvmsg+0x7c/0x2b0
[16750.924801] ___sys_recvmsg+0x70/0x98
[16750.928564] __sys_recvmsg+0x58/0xa0
[16750.932238] __arm64_sys_recvmsg+0x28/0x30
[16750.936453] el0_svc_common.constprop.3+0x90/0x158
[16750.941378] do_el0_svc+0x74/0x90
[16750.944784] el0_sync_handler+0x12c/0x1a8
[16750.948903] el0_sync+0x114/0x140
[16750.952312] Code: f9400003 f907f423 eb02007f 54fffd60 (b9401060)
[16750.958583] ---[ end trace c8ad181c2f4b8576 ]---
This patch drops the use of the static iterator, and instead every time
the function is called iterates to the idx-th position of the
linked-list.
It would be better to convert the code not to use linked list for
associated stations storage (since the chip has a limited number of
associated stations anyway - it could just be an array). Such a change
may be proposed in the future. In the meantime this patch can backported
into stable kernels in this simple form.
Fixes: 8baca1a34d ("mwifiex: dump station support in uap mode")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515075924.13841-1-pali@kernel.org
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507185914.GA15124@embeddedor
Currently there is a check if priv is null when calling lbtf_remove_card
but not in a previous call to if_usb_reset_dev that can also dereference
priv. Fix this by also only calling lbtf_remove_card if priv is null.
It is noteable that there don't seem to be any bugs reported that the
null pointer dereference has ever occurred, so I'm not sure if the null
check is required, but since we're doing a null check anyway it should
be done for both function calls.
Addresses-Coverity: ("Dereference before null check")
Fixes: baa0280f08 ("libertas_tf: don't defer firmware loading until start()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200501173900.296658-1-colin.king@canonical.com
gcc-10 reports a warning for mwifiex_cmd_802_11_key_material_v1:
drivers/net/wireless/marvell/mwifiex/sta_cmd.c: In function 'mwifiex_cmd_802_11_key_material_v1':
cc1: warning: writing 16 bytes into a region of size 0 [-Wstringop-overflow=]
In file included from drivers/net/wireless/marvell/mwifiex/sta_cmd.c:23:
drivers/net/wireless/marvell/mwifiex/fw.h:993:9: note: at offset 0 to object 'action' with size 2 declared here
993 | __le16 action;
| ^~~~~~
As the warning makes no sense, I reported it as a bug for gcc. In the
meantime using a temporary pointer for the key data makes the code easier
to read and stops the warning.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=94881
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200430213101.135134-4-arnd@arndb.de
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the following coccicheck warning:
drivers/net/wireless/marvell/libertas/cmdresp.c:225:5-8: Unneeded
variable: "ret". Return "0" on line 355
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200413082022.22380-1-yanaijie@huawei.com
Fix the following coccicheck warning:
drivers/net/wireless/marvell/libertas/mesh.c:833:5-8: Unneeded variable:
"ret". Return "0" on line 874
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410090942.27239-1-yanaijie@huawei.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200225020413.GA8057@embeddedor
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200225011709.GA601@embeddedor
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
hard_header_len provides limitations for things like AF_PACKET, such
that we don't allow transmitting packets smaller than this.
needed_headroom provides a suggested minimum headroom for SKBs, so that
we can trivally add our headers to the front.
The latter is the correct field to use in this case, while the former
mostly just prevents sending small AF_PACKET frames.
In any case, mwifiex already does its own bounce buffering [1] if we
don't have enough headroom, so hints (not hard limits) are all that are
needed.
This is the essentially the same bug (and fix) that brcmfmac had, fixed
in commit cb39288fd6 ("brcmfmac: use ndev->needed_headroom to reserve
additional header space").
[1] mwifiex_hard_start_xmit():
if (skb_headroom(skb) < MWIFIEX_MIN_DATA_HEADER_LEN) {
[...]
/* Insufficient skb headroom - allocate a new skb */
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.gbhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As of 6-DEC-2019, NXP has acquired Marvell’s Wireless business
unit. This change is to update the license text accordingly.
Signed-off-by: James Cao <zheng.cao@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit e5e884b426 ("libertas: Fix two buffer overflows at parsing bss
descriptor") introduced a bounds check on the number of supplied rates to
lbs_ibss_join_existing() and made it to return on overflow.
However, the aforementioned commit doesn't set the return value accordingly
and thus, lbs_ibss_join_existing() would return with zero even though it
failed.
Make lbs_ibss_join_existing return -EINVAL in case the bounds check on the
number of supplied rates fails.
Fixes: e5e884b426 ("libertas: Fix two buffer overflows at parsing bss descriptor")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit e5e884b426 ("libertas: Fix two buffer overflows at parsing bss
descriptor") introduced a bounds check on the number of supplied rates to
lbs_ibss_join_existing().
Unfortunately, it introduced a return path from within a RCU read side
critical section without a corresponding rcu_read_unlock(). Fix this.
Fixes: e5e884b426 ("libertas: Fix two buffer overflows at parsing bss descriptor")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_cmd_append_vsie_tlv() calls memcpy() without checking
the destination size may trigger a buffer overflower,
which a local user could use to cause denial of service
or the execution of arbitrary code.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Qing Xu <m1s5p6688@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_ret_wmm_get_status() calls memcpy() without checking the
destination size.Since the source is given from remote AP which
contains illegal wmm elements , this may trigger a heap buffer
overflow.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Qing Xu <m1s5p6688@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We called rcu_read_lock(), so we need to call rcu_read_unlock() before
we return.
Fixes: 3d94a4a837 ("mwifiex: fix possible heap overflow in mwifiex_process_country_ie()")
Cc: stable@vger.kernel.org
Cc: huangwen <huangwenabc@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeLcWsAAoJEG4XJFUm622bDGUIAJuhM4LiDAzOGnDjH5cMosOC
/qwDpGD19cEeVAhNSMKUn7Uo9+qbQYIleiO7XXxzCuJceYbxbT5s3Vb/fWsRUPjS
cBDmGuK8/giqMQJshXvfCTsoF83CyirCjY/MJvomK2BRlXM8hQ3s6hAcfU0zQ96e
OU1akcfZzUwjaBKaDYLncxLuGbeUXMy8AZwFdgQlQRMoObpen/IIwx6jDK/A+3l6
VCOJF+JTkDytfNWmTpZ65uJrYEXoLe6G4028FjOI4BDFmEgvdHC5vTm7VOBhrkuB
9tsKcYNvECCNn2WI96V+etD8kaZPscQIW8hgOrYyGxw43lJg5zH4Z9eWAmHojxE=
=UOhb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 1e58252e33 ("mwifiex: Fix heap overflow in
mmwifiex_process_tdls_action_frame()"),
mwifiex_process_tdls_action_frame() already had too many magic numbers.
But this commit just added a ton more, in the name of checking for
buffer overflows. That seems like a really bad idea.
Let's make these magic numbers a little less magic, by
(a) factoring out 'pos[1]' as 'ie_len'
(b) using 'sizeof' on the appropriate source or destination fields where
possible, instead of bare numbers
(c) dropping redundant checks, per below.
Regarding redundant checks: the beginning of the loop has this:
if (pos + 2 + pos[1] > end)
break;
but then individual 'case's include stuff like this:
if (pos > end - 3)
return;
if (pos[1] != 1)
return;
Note that the second 'return' (validating the length, pos[1]) combined
with the above condition (ensuring 'pos + 2 + length' doesn't exceed
'end'), makes the first 'return' (whose 'if' can be reworded as 'pos >
end - pos[1] - 2') redundant. Rather than unwind the magic numbers
there, just drop those conditions.
Fixes: 1e58252e33 ("mwifiex: Fix heap overflow in mmwifiex_process_tdls_action_frame()")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeKX2wAAoJEG4XJFUm622bG8QH/3+QXaSJAVqzbQh2boy7aS88
xhrrnh+bSqWY0ChMk0Z73RF8Ek0WlO+os4uN1cbWIWujrdQUPbTBtOwX4d0TzTue
E3tBFPiHTlVtU43z1bsprA+6EE7fqt/H2lWtlxk0IHzeiQY9NcB6BlDKKCzk5Hib
aMb5HCQy4JmSK83E60HLM9L4nEmEP+yveaKL7uaAZw+qkmyk2mT6um0TlmOYVoNG
9V6k3OZto8LvyV6jKPZgVI6QBATnwHDxlWgooYRj54PuCj9hTbR2mcuUL2QyQeze
AX2QNI+1kWIrAiDaU/lOj8579SiUl36iqtuKmtLhDnSe1GxDkrzmawtz3aGDm4k=
=VZox
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
First set of patches for v5.6. The biggest thing here is of course the
new driver ath11k but also new features for other drivers as well a
myriad of bug fixes.
Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
brcmfmac
* add support for BCM4359 SDIO chipset
wil6210
* support set_multicast_to_unicast cfg80211 operation
* support set_cqm_rssi_config cfg80211 operation
wcn36xx
* disable HW_CONNECTION_MONITOR as firmware is buggy
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd/OTiAAoJEG4XJFUm622bN3MH+gM/uwAyMUOLK/x+9dyL+nnO
y8/QbtkM9eyMaMJ+8BoA4XVs8Md5K0YPEUoV22VoTKXgRLX5G2dwoFC5TbuuIxGF
6ptojEoc6XsYYOySHGlgEwPhR8UYf3YfvpgerqbENeiCA82ZHrY9MSUEReEGLr6U
OSb+qcP1KtwpIvo8u4hhomJQO4vO1iY+Z1+6tUzDzpzk3t/rsX2dg9083Cw46JgT
deruvZziwFLsws4EVoBUxa9OPg4Jz/zelRlgHpAXi4VWr7GM9p2cqTia0OwE/coX
VCberklKTJLQfpp5L3uZ9QX4MwSwhTJC/rPiwm9a+4TezT7yVAexF2Q+L/nKKRQ=
=nRvm
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
First set of patches for v5.6. The biggest thing here is of course the
new driver ath11k but also new features for other drivers as well a
myriad of bug fixes.
Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
brcmfmac
* add support for BCM4359 SDIO chipset
wil6210
* support set_multicast_to_unicast cfg80211 operation
* support set_cqm_rssi_config cfg80211 operation
wcn36xx
* disable HW_CONNECTION_MONITOR as firmware is buggy
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7afb94da3c ("mwifiex: update set_mac_address logic") fixed the
only user of this function, partly because the author seems to have
noticed that, as written, it's on the borderline between highly
misleading and buggy.
Anyway, no sense in keeping dead code around: let's drop it.
Fixes: 7afb94da3c ("mwifiex: update set_mac_address logic")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add_ie_rates() copys rates without checking the length
in bss descriptor from remote AP.when victim connects to
remote attacker, this may trigger buffer overflow.
lbs_ibss_join_existing() copys rates without checking the length
in bss descriptor from remote IBSS node.when victim connects to
remote attacker, this may trigger buffer overflow.
Fix them by putting the length check before performing copy.
This fix addresses CVE-2019-14896 and CVE-2019-14897.
This also fix build warning of mixed declarations and code.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Wen Huang <huangwenabc@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd+P4eAAoJEG4XJFUm622bnOQH/RHSFFQNjxfPboZoozKb0/mT
6YtrG+0K1z8E21Os2bd+s4aRJgq1oGKDocMie5y53M38qQ5N3FchzcGopNRCRy/a
gF1PzEqceOysbEtPOx4yI+c0Gfi7rS0SjEyf2XKGowXsoIZh4j+1xlWbF/JtHt6n
J901W1GW0ZUCHaP8KuZcbsS2nfdV8tFW2NQW3Xuhy+nOdBhNRL/lKSvlhZLCCAfY
f1eJrB0rAzQpCqw8Wuz2JzWsxBiTt+6Ucuzv4EkFVrt7Xnj00feghTKJkVDqa+fL
B9hTiiYh8sLGJkYHsZLDZIzAdOW8jmun1I+XFsjdl7ucLRYz6U8NL9jc6oIGK00=
=KJmM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2019-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
mwifiex_process_tdls_action_frame() without checking
the incoming tdls infomation element's vality before use it,
this may cause multi heap buffer overflows.
Fix them by putting vality check before use it.
IE is TLV struct, but ht_cap and ht_oper aren’t TLV struct.
the origin marvell driver code is wrong:
memcpy(&sta_ptr->tdls_cap.ht_oper, pos,....
memcpy((u8 *)&sta_ptr->tdls_cap.ht_capb, pos,...
Fix the bug by changing pos(the address of IE) to
pos+2 ( the address of IE value ).
Signed-off-by: qize wang <wangqize888888888@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_process_country_ie() function parse elements of bss
descriptor in beacon packet. When processing WLAN_EID_COUNTRY
element, there is no upper limit check for country_ie_len before
calling memcpy. The destination buffer domain_info->triplet is an
array of length MWIFIEX_MAX_TRIPLET_802_11D(83). The remote
attacker can build a fake AP with the same ssid as real AP, and
send malicous beacon packet with long WLAN_EID_COUNTRY elemen
(country_ie_len > 83). Attacker can force STA connect to fake AP
on a different channel. When the victim STA connects to fake AP,
will trigger the heap buffer overflow. Fix this by checking for
length and if found invalid, don not connect to the AP.
This fix addresses CVE-2019-14895.
Reported-by: huangwen <huangwenabc@gmail.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
- Add CMD13 polling for MMC IOCTLS with R1B response.
- Add common DT properties for clk-phase-delays for various speed modes.
- Fix size overflow for mmc gp-partitions.
- Re-work HW reset for SDIO cards, which also includes a re-work for
Marvell's WiFi mwifiex SDIO func driver.
MMC host:
- jz4740: Add support for X1000 and JZ4760.
- jz4740: Add support for 8-bit bus and for low power mode.
- mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
- owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
- renesas_sdhi: Add support for r8a774b1.
- sdhci_am654: Add support for Command Queuing Engine for J721E.
- sdhci-milbeaut: Add driver for the Milbeaut SD controller.
- sdhci-of-arasan: Add support for ZynqMP tap-delays.
- sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
- sdhci-of-arasan: Add support for Intel LGM SDXC.
- sdhci-of-aspeed: Allow inversion of the internal card detect signal.
- sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
- sdhci-of-at91: Improve support for calibration.
- sdhci-pci: Add support for Intel JSL.
- sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
- tmio: Enable support for erase/discard/trim requests.
MMC/OMAP/pandora/wl1251:
The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has been
broken since v4.7. To fix the problems, changes have been made cross
subsystems, but also to OMAP2 machine code and to openpandora DTS files, as
summarized below. Note that, relevant changes have been tagged for stable.
- mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
- omap/omap_hsmmc: Remove redundant platform config for openpandora
- omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
- omap/dts/pandora: Specify wl1251 through a child node of mmc3
- wl1251: Add devicetree support for TI wl1251 SDIO
-----BEGIN PGP SIGNATURE-----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=WOaQ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"These are the updates for MMC and MEMSTICK for v5.5.
Note that this also contains quite some additional changes reaching
beyond both the MMC and MEMSTICK subsystems. This is primarily because
of fixing an old regression for a WiFi driver based on the SDIO
interface on an OMAP openpandora board
MMC core:
- Add CMD13 polling for MMC IOCTLS with R1B response.
- Add common DT properties for clk-phase-delays for various speed
modes.
- Fix size overflow for mmc gp-partitions.
- Re-work HW reset for SDIO cards, which also includes a re-work for
Marvell's WiFi mwifiex SDIO func driver.
MMC host:
- jz4740: Add support for X1000 and JZ4760.
- jz4740: Add support for 8-bit bus and for low power mode.
- mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
- owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
- renesas_sdhi: Add support for r8a774b1.
- sdhci_am654: Add support for Command Queuing Engine for J721E.
- sdhci-milbeaut: Add driver for the Milbeaut SD controller.
- sdhci-of-arasan: Add support for ZynqMP tap-delays.
- sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
- sdhci-of-arasan: Add support for Intel LGM SDXC.
- sdhci-of-aspeed: Allow inversion of the internal card detect
signal.
- sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
- sdhci-of-at91: Improve support for calibration.
- sdhci-pci: Add support for Intel JSL.
- sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
- tmio: Enable support for erase/discard/trim requests.
MMC/OMAP/pandora/wl1251:
The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has
been broken since v4.7. To fix the problems, changes have been made
cross subsystems, but also to OMAP2 machine code and to openpandora
DTS files, as summarized below. Relevant changes have been tagged for
stable.
- mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
- omap/omap_hsmmc: Remove redundant platform config for openpandora
- omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
- omap/dts/pandora: Specify wl1251 through a child node of mmc3
- wl1251: Add devicetree support for TI wl1251 SDIO"
* tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (73 commits)
dt-bindings: mmc: Correct the type of the clk phase properties
Revert "mmc: tmio: remove workaround for NON_REMOVABLE"
memstick: Fix Kconfig indentation
mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup
dt-bindings: mmc: arasan: Document 'xlnx,zynqmp-8.9a' controller
firmware: xilinx: Add SDIO Tap Delay nodes
mmc: sdhci-of-arasan: Add support to set clock phase delays for SD
dt-bindings: mmc: Add optional generic properties for mmc
mmc: sdhci-of-arasan: Add sampling clock for a phy to use
dt-bindings: mmc: arasan: Update Documentation for the input clock
mmc: sdhci-of-arasan: Separate out clk related data to another structure
mmc: sdhci: Fix grammar in warning message
mmc: sdhci-of-aspeed: add inversion signal presence
mmc: sdhci-of-aspeed: enable CONFIG_MMC_SDHCI_IO_ACCESSORS
mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E
mmc: core: Fix size overflow for mmc partitions
mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requests
net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitions
net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definition
mmc: core: fix wl1251 sdio quirks
...
The SDIO HW reset procedure in mwifiex_sdio_card_reset_work() is broken,
when the SDIO card is shared with another SDIO func driver. This is the
case when the Bluetooth btmrvl driver is being used in combination with
mwifiex. More precisely, when mwifiex_sdio_card_reset_work() runs to resets
the SDIO card, the btmrvl driver doesn't get notified about it. Beyond that
point, the btmrvl driver will fail to communicate with the SDIO card.
This is a generic problem for SDIO func drivers sharing an SDIO card, which
are about to be addressed in subsequent changes to the mmc core and the
mmc_hw_reset() interface. In principle, these changes means the
mmc_hw_reset() interface starts to return 1 if the are multiple drivers for
the SDIO card, as to indicate to the caller that the reset needed to be
scheduled asynchronously through a hotplug mechanism of the SDIO card.
Let's prepare the mwifiex driver to support the upcoming new behaviour of
mmc_hw_reset(), which means extending the mwifiex_sdio_card_reset_work() to
support the asynchronous SDIO HW reset path. This also means, we need to
allow the ->remove() callback to run, without waiting for the FW to be
loaded. Additionally, during system suspend, mwifiex_sdio_suspend() may be
called when a reset has been scheduled, but waiting to be executed. In this
scenario let's simply return -EBUSY to abort the suspend process, as to
allow the reset to be completed first.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # v5.4+
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
