mwifiex_band_2ghz and mwifiex_band_5ghz are statically allocated, but
used and modified in driver instances. Duplicate them before using
them in driver instances so that different driver instances do not
influence each other.
This was observed on a board which has one PCIe and one SDIO mwifiex
adapter. It blew up in mwifiex_setup_ht_caps(). This was called with
the statically allocated struct which is modified in this function.
Cc: stable@vger.kernel.org
Fixes: d6bffe8bb5 ("mwifiex: support for creation of AP interface")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240809-mwifiex-duplicate-static-structs-v1-1-6837b903b1a4@pengutronix.de
bss_config->key_mgmt specifies the AKM suites that are usable in
hardware. This variable is set to specific values while iterating
over the advertised AKM suites. This means the final value of the
variable depends on the order of the entries in the AKM suites
array. Instead of setting the variable, just set the relevant bits
in the key_mgmt bit field to make us independent of the order of
entries.
This behaviour is derived from the downstream driver that does the
same.
Also, set bss_config->key_mgmt to zero explicitly right before the
loop. bss_config has been zero allocated by the caller already, but
do so again to save the reader from following the code path.
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20240723-mwifiex-wpa-psk-sha256-v3-2-025168a91da1@pengutronix.de
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240805-mwifiex-wpa-psk-sha256-v4-2-e1eee80508e6@pengutronix.de
The WPA flags setting only depends on the wpa_versions bitfield and not
on the AKM suite, so move it out of the switch/case to simplify the code
a bit. Also set bss_config->protocol to zero explicitly. This is done
only to make the code clearer, bss_config has been zero alloced by the
caller, so should be zero already. No functional change intended.
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20240723-mwifiex-wpa-psk-sha256-v3-1-025168a91da1@pengutronix.de
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240805-mwifiex-wpa-psk-sha256-v4-1-e1eee80508e6@pengutronix.de
Add host based MLME to enable WPA3 functionalities in AP mode.
This feature required a firmware with the corresponding V2 Key API
support. The feature (WPA3) is currently enabled and verified only
on IW416. Also, verified no regression with change when host MLME
is disabled.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240704033001.603419-3-yu-hao.lin@nxp.com
Add host based MLME to enable WPA3 functionalities in client mode.
This feature required a firmware with the corresponding V2 Key API
support. The feature (WPA3) is currently enabled and verified only
on IW416. Also, verified no regression with change when host MLME
is disabled.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240704033001.603419-2-yu-hao.lin@nxp.com
The maximum number of AKM suites will be set to two if not specified by
the driver. Set it to CFG80211_MAX_NUM_AKM_SUITES to let userspace
specify up to ten AKM suites in the akm_suites array.
Without only the first two AKM suites will be used, further ones are
ignored.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240530130156.1651174-1-s.hauer@pengutronix.de
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have two
conflicts this time:
CONFLICT (content): Merge conflict in net/mac80211/cfg.c
CONFLICT (content): Merge conflict in drivers/net/wireless/microchip/wilc1000/netdev.c
Here are Stephen's resolutions for them:
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au/https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au/
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* Enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZi07URHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZu3/QgAo7jyKgvpwMaNIVRLyfYCo0r3Q9wb7QPd
QeRNsftYxlWpPTJ4+Y95aZupy91Ay+RaEQXbbtl7PMIiyQrs7wb4V4Iqzedkws3t
DZsR5BitH+1BIGY0Omo0fiSB5HlWEwZGUj6inqlgKHpBtdIVTANSMjuwkdoMAV5y
ZU57axIGToySvDbRlhJQW833Nnh4KnaseA+TtyfXSaBVerzbshkjBr0d9pMBMiH9
irMQW5CW+7fbxp3OCNsKxX4eG6MFGmm/uP1hFmeYQi2qzUE4SddHMeV4I6oNKOrH
vFB+ZVmYvOjJUYsNhlCUe6Vy+EKwvmfiDWwE1egelEkgozCixJXAAQ==
=QT4C
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.11
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have
two conflicts this time:
net/mac80211/cfg.c
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au
drivers/net/wireless/microchip/wilc1000/netdev.c
https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA)
support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
* tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (194 commits)
wifi: ath12k: add hw_link_id in ath12k_pdev
wifi: ath12k: add panic handler
wifi: rtw89: chan: Use swap() in rtw89_swap_sub_entity()
wifi: brcm80211: remove unused structs
wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type)
wifi: ath12k: do not process consecutive RDDM event
dt-bindings: net: wireless: ath11k: Drop "qcom,ipq8074-wcss-pil" from example
wifi: ath12k: fix memory leak in ath12k_dp_rx_peer_frag_setup()
wifi: rtlwifi: handle return value of usb init TX/RX
wifi: rtlwifi: Enable the new rtl8192du driver
wifi: rtlwifi: Add rtl8192du/sw.c
wifi: rtlwifi: Constify rtl_hal_cfg.{ops,usb_interface_cfg} and rtl_priv.cfg
wifi: rtlwifi: Add rtl8192du/dm.{c,h}
wifi: rtlwifi: Add rtl8192du/fw.{c,h} and rtl8192du/led.{c,h}
wifi: rtlwifi: Add rtl8192du/rf.{c,h}
wifi: rtlwifi: Add rtl8192du/trx.{c,h}
wifi: rtlwifi: Add rtl8192du/phy.{c,h}
wifi: rtlwifi: Add rtl8192du/hw.{c,h}
wifi: rtlwifi: Add new members to struct rtl_priv for RTL8192DU
wifi: rtlwifi: Add rtl8192du/table.{c,h}
...
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Link: https://lore.kernel.org/r/20240607093517.41394C2BBFC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When changing the interface type we also need to update the bss_num, the
driver private data is searched based on a unique (bss_type, bss_num)
tuple, therefore every time bss_type changes, bss_num must also change.
This fixes for example an issue in which, after the mode changed, a
wireless scan on the changed interface would not finish, leading to
repeated -EBUSY messages to userspace when other scan requests were
sent.
Fixes: c606008b70 ("mwifiex: Properly initialize private structure on interface type changes")
Cc: stable@vger.kernel.org
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240510110458.15475-1-francesco@dolcini.it
- Increase the timeout period of the ACMD41 command
- Add card entry for quirks to debugfs
- Add mmc_gpiod_set_cd_config() function
- Store owner from SDIO modules with sdio_register_driver()
MMC host:
- atmel-mci: Some cleanups and a switch to use dev_err_probe()
- renesas_sdhi: Add support for RZ/G2L, RZ/G3S and RZ/V2M variants
- renesas_sdhi: Set the SDBUF after reset
- sdhci: Add support for "Tuning Error" interrupts
- sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA
- sdhci-acpi: Disable write protect detection on Toshiba WT10-A
- sdhci-acpi: Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
- sdhci_am654: Re-work and fix the tuning support for multiple speed-modes
- sdhci_am654: Add tuning algorithm for delay chain
- sdhci-esdhc-imx: Add NXP S32G3 support
- sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X
- sdhci-of-dwcmshc: Implement SDHCI CQE support
- sdhci-pci-gli: Use the proper pci_set_power_state() instead of PMCSR writes
MEMSTICK:
- Convert a couple of drivers to use the ->remove_new() callback
-----BEGIN PGP SIGNATURE-----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=I2JP
-----END PGP SIGNATURE-----
Merge tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Increase the timeout period of the ACMD41 command
- Add card entry for quirks to debugfs
- Add mmc_gpiod_set_cd_config() function
- Store owner from SDIO modules with sdio_register_driver()
MMC host:
- atmel-mci: Some cleanups and a switch to use dev_err_probe()
- renesas_sdhi:
- Add support for RZ/G2L, RZ/G3S and RZ/V2M variants
- Set the SDBUF after reset
- sdhci: Add support for "Tuning Error" interrupts
- sdhci-acpi:
- Add quirk to enable pull-up on the card-detect GPIO on Asus
T100TA
- Disable write protect detection on Toshiba WT10-A
- Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
- sdhci_am654:
- Re-work and fix the tuning support for multiple speed-modes
- Add tuning algorithm for delay chain
- sdhci-esdhc-imx: Add NXP S32G3 support
- sdhci-of-dwcmshc:
- Add tuning support for Sophgo CV1800B and SG200X
- Implement SDHCI CQE support
- sdhci-pci-gli: Use the proper pci_set_power_state() instead of
PMCSR writes"
MEMSTICK:
- Convert a couple of drivers to use the ->remove_new() callback"
* tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits)
mmc: renesas_sdhi: Add compatible string for RZ/G2L family, RZ/G3S, and RZ/V2M SoCs
dt-bindings: mmc: renesas,sdhi: Document RZ/G2L family compatibility
dt-bindings: mmc: renesas,sdhi: Group single const value items into an enum list
mmc: renesas_sdhi: Set the SDBUF after reset
mmc: core: Increase the timeout period of the ACMD41 command
mmc: core: Convert to use __mmc_poll_for_busy() SD_APP_OP_COND too
mmc: atmel-mci: Switch to use dev_err_probe()
mmc: atmel-mci: Incapsulate used to be a platform data into host structure
mmc: atmel-mci: Replace platform device pointer by generic one
mmc: atmel-mci: Use temporary variable for struct device
mmc: atmel-mci: Get rid of platform data leftovers
mmc: sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X
mmc: sdhci-of-dwcmshc: Remove useless "&" of th1520_execute_tuning
mmc: sdhci-s3c: Choose sdhci_ops based on variant
mmc: sdhci_am654: Constify struct sdhci_ops
mmc: sdhci-sprd: Constify struct sdhci_ops
mmc: sdhci-omap: Constify struct sdhci_ops
mmc: sdhci-esdhc-mcf: Constify struct sdhci_ops
mmc: slot-gpio: Use irq_handler_t type
mmc: sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA
...
Use module_sdio_driver() instead of open-coding it. No functional
difference.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240329171019.63836-6-krzysztof.kozlowski@linaro.org
Core in sdio_register_driver() already sets the .owner, so driver does
not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240403-module-owner-sdio-v2-6-ae46d6b955eb@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The module metadata for the firmware file mrvl/sd8801_uapsta.bin
is missing.
Signed-off-by: Víctor Gonzalo <victor.gonzalo@anddroptable.net>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240313183156.2234301-1-victor.gonzalo@anddroptable.net
struct mwifiex_ie_types_chan_list_param_set::chan_scan_param is treated
as a flexible array, so convert it into one so that it doesn't trip
the array bounds sanitizer[1]. Only a few places were using sizeof()
on the whole struct, so adjust those to follow the calculation pattern
to avoid including the trailing single element.
Examining binary output differences doesn't appear to show any literal
size values changing, though it is obfuscated a bit by the compiler
adjusting register usage and stack spill slots, etc.
Link: https://github.com/KSPP/linux/issues/51 [1]
Cc: Brian Norris <briannorris@chromium.org>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Dmitry Antipov <dmantipov@yandex.ru>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: zuoqilin <zuoqilin@yulong.com>
Cc: Ruan Jinjie <ruanjinjie@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240207103024.make.423-kees@kernel.org
Use convenient 'kstrtou32_from_user()' in 'mwifiex_verext_write()'
and 'kstrtobool_from_user()' in 'mwifiex_timeshare_coex_write()',
respectively. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240110115314.421298-1-dmantipov@yandex.ru
Aloka originally suggested that puncturing should be part of
the chandef, so that it's treated correctly. At the time, I
disagreed and it ended up not part of the chandef, but I've
now realized that this was wrong. Even for clients, the RX,
and perhaps more importantly, CCA configuration needs to take
puncturing into account.
Move puncturing into the chandef, and adjust all the code
accordingly. Also add a few tests for puncturing in chandef
compatibility checking.
Link: https://lore.kernel.org/linux-wireless/20220214223051.3610-1-quic_alokad@quicinc.com/
Suggested-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://msgid.link/20240129194108.307183a5d2e5.I4d7fe2f126b2366c1312010e2900dfb2abffa0f6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mwifiex driver include two legacy GPIO headers but does
not use symbols from any of them.
The driver does contain some "gpio" handling code, but this
is some custom GPIO interface, not the Linux GPIO.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-4-e1c7c5d68746@linaro.org
The first "new features" pull request for v6.9. We have only driver
changes this time and most of them are for Realtek drivers. Really
nice to see activity in Broadcom drivers again.
Major changes:
rtwl8xxxu
* RTL8188F: concurrent interface support
* Channel Switch Announcement (CSA) support in AP mode
brcmfmac
* per-vendor feature support
* per-vendor SAE password setup
rtlwifi
* speed up USB firmware initialisation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmWyOigRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt2OAf8DG1/4j+iBanejbVb1IVYklIG1lt6L092
kwnBZO+I0TAF9u5LGr91kyuZJ/2AQUi8awcE4364D54tTVAqDSl/ZwdiTbYZdemq
/JiJeNYuVTaJ5wu0Kk5jdMMdCgwV570JLcEXcf+jvxZj7HGz8HeT5MH19nLN7O+Z
irbfSldYeL5b/f+4UUlgZsa87tZ/E/LOEK28Vf6tWRLXZOdyUCXsKS1z6UOr4pFb
d1QKenu/wYoc0hHbWcwa3G8zmIm7IdtpIWePPF3j8Gj7WntDVtY49llP7A4m3WnG
/u5iPAj/xwkLiCADLBwKYkWC1yREQ0EGlv9gcocfF50METB4OGH7YQ==
=CgVA
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-01-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The first "new features" pull request for v6.9. We have only driver
changes this time and most of them are for Realtek drivers. Really
nice to see activity in Broadcom drivers again.
Major changes:
rtwl8xxxu
* RTL8188F: concurrent interface support
* Channel Switch Announcement (CSA) support in AP mode
brcmfmac
* per-vendor feature support
* per-vendor SAE password setup
rtlwifi
* speed up USB firmware initialisation
* tag 'wireless-next-2024-01-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (105 commits)
wifi: iwlegacy: Use kcalloc() instead of kzalloc()
wifi: rtw89: fix disabling concurrent mode TX hang issue
wifi: rtw89: fix HW scan timeout due to TSF sync issue
wifi: rtw89: add wait/completion for abort scan
wifi: rtw89: fix null pointer access when abort scan
wifi: rtw89: disable RTS when broadcast/multicast
wifi: rtw89: Set default CQM config if not present
wifi: rtw89: refine hardware scan C2H events
wifi: rtw89: refine add_chan H2C command to encode_bits
wifi: rtw89: 8922a: add BTG functions to assist BT coexistence to control TX/RX
wifi: rtw89: 8922a: add TX power related ops
wifi: rtw89: 8922a: add register definitions of H2C, C2H, page, RRSR and EDCCA
wifi: rtw89: 8922a: add chip_ops related to BB init
wifi: rtw89: 8922a: add chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add mlo_dbcc_mode for WiFi 7 chips
wifi: rtlwifi: Speed up firmware loading for USB
wifi: rtl8xxxu: add missing number of sec cam entries for all variants
wifi: brcmfmac: allow per-vendor event handling
wifi: brcmfmac: avoid invalid list operation when vendor attach fails
wifi: brcmfmac: Demote vendor-specific attach/detach messages to info
...
====================
Link: https://lore.kernel.org/r/20240125104030.B6CA6C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
debugfs_create_dir() returns ERR_PTR and never return NULL.
As Russell suggested, this patch removes the error checking for
debugfs_create_dir(). This is because the DebugFS kernel API is developed
in a way that the caller can safely ignore the errors that occur during
the creation of DebugFS nodes. The debugfs APIs have a IS_ERR() judge in
start_creating() which can handle it gracefully. So these checks are
unnecessary.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20230903030216.1509013-3-ruanjinjie@huawei.com
There is usbdrv_wrap in struct usb_driver and usb_device_driver, it
contains device_driver and for_devices. for_devices is used to
distinguish between device drivers and interface drivers.
Like the is_usb_device(), it tests the type of the device. We can test
that if the probe of device_driver is equal to usb_probe_device in
is_usb_device_driver(), and then the struct usbdrv_wrap is no longer
needed.
Clean up struct usbdrv_wrap, use device_driver directly in struct
usb_driver and usb_device_driver. This makes the code cleaner.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AP BSSID configuration is missing at AP start. Without this fix, FW returns
STA interface MAC address after first init. When hostapd restarts, it gets MAC
address from netdev before driver sets STA MAC to netdev again. Now MAC address
between hostapd and net interface are different causes STA cannot connect to
AP. After that MAC address of uap0 mlan0 become the same. And issue disappears
after following hostapd restart (another issue is AP/STA MAC address become the
same).
This patch fixes the issue cleanly.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Fixes: 12190c5d80 ("mwifiex: add cfg80211 start_ap and stop_ap handlers")
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Rafael Beims <rafael.beims@toradex.com> # Verdin iMX8MP/SD8997 SD
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231215005118.17031-1-yu-hao.lin@nxp.com
For SDIO IW416, due to a bug, FW may return ready before complete full
initialization. Command timeout may occur at driver load after reboot.
Workaround by adding 100ms delay at checking FW status.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin AM62 (IW416)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231208234029.2197-1-yu-hao.lin@nxp.com
Clang static analyzer complains that value stored to 'priv' is never read.
'priv' is useless, so remove it to save space.
Signed-off-by: Su Hui <suhui@nfschina.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231115092328.1048103-1-suhui@nfschina.com
Resolve several conflicts, mostly between changes/fixes in
wireless and the locking rework in wireless-next. One of
the conflicts actually shows a bug in wireless that we'll
want to fix separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Using the full struct cfg80211_ap_settings for an update is
misleading, since most settings cannot be updated. Split the
update case off into a new struct cfg80211_ap_update.
Change-Id: I3ba4dd9280938ab41252f145227a7005edf327e4
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce a few more (PCIE and generic interface related)
cleanups which becomes reasonable after the previous patch.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230919132804.73340-2-dmantipov@yandex.ru
Since 'mwifiex_write_reg()' just issues void 'iowrite32()',
convert the former to 'void' and simplify all related users
(with the only exception of 'read_poll_timeout()' which
explicitly requires a non-void function argument).
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230919132804.73340-1-dmantipov@yandex.ru
The mwifiex_pcie driver is missing the MODULE_FIRMWARE macro to
add the firmware files needed to the module metadata.
Signed-off-by: Víctor Gonzalo <victor.gonzalo@anddroptable.net>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230914211938.28395-1-victor.gonzalo@anddroptable.net
Drop filled with NULL pointers but otherwise unused 'skb_arr'
array of 'struct mwifiex_sdio_mpa_rx', adjust related code.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230821115254.167552-1-dmantipov@yandex.ru
Only skip the code path trying to access the rfc1042 headers when the
buffer is too small, so the driver can still process packets without
rfc1042 headers.
Fixes: 1195852816 ("wifi: mwifiex: Fix OOB and integer underflow when rx packets")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Acked-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthew Wang <matthewmwang@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908104308.1546501-1-treapking@chromium.org
Modify the prototype for change_beacon() in struct cfg80211_op to
accept cfg80211_ap_settings instead of cfg80211_beacon_data so that
it can process data in addition to beacons.
Modify the prototypes of ieee80211_change_beacon() and driver specific
functions accordingly.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20230727174100.11721-4-quic_alokad@quicinc.com
[while at it, remove pointless "if (info)" check in tracing that just
makes all the lines longer than they need be - it's never NULL]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we're now protecting everything with the wiphy mutex
(and were really using it for almost everything before),
there's no longer any real reason to have a separate wdev
mutex. It may feel better, but really has no value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add sanity checks for both `tlv_len` and `tlv_bitmap_len` before
decoding data from `event_buf`.
This prevents any malicious or buggy firmware from overflowing
`event_buf` through large values for `tlv_len` and `tlv_bitmap_len`.
Suggested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/d4f8780527d551552ee96f17a0229e02e1c200d1.1692931954.git.gustavoars@kernel.org
One-element and zero-length arrays are deprecated. So, replace
one-element array in struct mwifiex_ie_types_rxba_sync with
flexible-array member, and refactor the rest of the code, accordingly.
This results in no differences in binary output.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/79c801c69c8beece2f80502c60166036d3c047cc.1692931954.git.gustavoars@kernel.org
In a TLV encoding scheme, the Length part represents the length after
the header containing the values for type and length. In this case,
`tlv_len` should be:
tlv_len == (sizeof(*tlv_rxba) - 1) - sizeof(tlv_rxba->header) + tlv_bitmap_len
Notice that the `- 1` accounts for the one-element array `bitmap`, which
1-byte size is already included in `sizeof(*tlv_rxba)`.
So, if the above is correct, there is a double-counting of some members
in `struct mwifiex_ie_types_rxba_sync`, when `tlv_buf_left` and `tmp`
are calculated:
968 tlv_buf_left -= (sizeof(*tlv_rxba) + tlv_len);
969 tmp = (u8 *)tlv_rxba + tlv_len + sizeof(*tlv_rxba);
in specific, members:
drivers/net/wireless/marvell/mwifiex/fw.h:777
777 u8 mac[ETH_ALEN];
778 u8 tid;
779 u8 reserved;
780 __le16 seq_num;
781 __le16 bitmap_len;
This is clearly wrong, and affects the subsequent decoding of data in
`event_buf` through `tlv_rxba`:
970 tlv_rxba = (struct mwifiex_ie_types_rxba_sync *)tmp;
Fix this by using `sizeof(tlv_rxba->header)` instead of `sizeof(*tlv_rxba)`
in the calculation of `tlv_buf_left` and `tmp`.
This results in the following binary differences before/after changes:
| drivers/net/wireless/marvell/mwifiex/11n_rxreorder.o
| @@ -4698,11 +4698,11 @@
| drivers/net/wireless/marvell/mwifiex/11n_rxreorder.c:968
| tlv_buf_left -= (sizeof(tlv_rxba->header) + tlv_len);
| - 1da7: lea -0x11(%rbx),%edx
| + 1da7: lea -0x4(%rbx),%edx
| 1daa: movzwl %bp,%eax
| drivers/net/wireless/marvell/mwifiex/11n_rxreorder.c:969
| tmp = (u8 *)tlv_rxba + sizeof(tlv_rxba->header) + tlv_len;
| - 1dad: lea 0x11(%r15,%rbp,1),%r15
| + 1dad: lea 0x4(%r15,%rbp,1),%r15
The above reflects the desired change: avoid counting 13 too many bytes;
which is the total size of the double-counted members in
`struct mwifiex_ie_types_rxba_sync`:
$ pahole -C mwifiex_ie_types_rxba_sync drivers/net/wireless/marvell/mwifiex/11n_rxreorder.o
struct mwifiex_ie_types_rxba_sync {
struct mwifiex_ie_types_header header; /* 0 4 */
|-----------------------------------------------------------------------
| u8 mac[6]; /* 4 6 */ |
| u8 tid; /* 10 1 */ |
| u8 reserved; /* 11 1 */ |
| __le16 seq_num; /* 12 2 */ |
| __le16 bitmap_len; /* 14 2 */ |
| u8 bitmap[1]; /* 16 1 */ |
|----------------------------------------------------------------------|
| 13 bytes|
-----------
/* size: 17, cachelines: 1, members: 7 */
/* last cacheline: 17 bytes */
} __attribute__((__packed__));
Fixes: 99ffe72cda ("mwifiex: process rxba_sync event")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/06668edd68e7a26bbfeebd1201ae077a2a7a8bce.1692931954.git.gustavoars@kernel.org
In 'mwifiex_handle_uap_rx_forward()', always check the value
returned by 'skb_copy()' to avoid potential NULL pointer
dereference in 'mwifiex_uap_queue_bridged_pkt()', and drop
original skb in case of copying failure.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 838e4f4492 ("mwifiex: improve uAP RX handling")
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230814095041.16416-1-dmantipov@yandex.ru
Remove unused and set but unused 'dfs_workqueue', 'dfs_work', and
'scan_channels' members of 'struct mwifiex_adapter', adjust users.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230814142101.60308-1-dmantipov@yandex.ru
Add missed return in mwifiex_uap_queue_bridged_pkt() and
mwifiex_process_rx_packet().
Fixes: 1195852816 ("wifi: mwifiex: Fix OOB and integer underflow when rx packets")
Signed-off-by: Polaris Pi <pinkperfect2021@gmail.com>
Reported-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230810083911.3725248-1-pinkperfect2021@gmail.com
Use is_zero_ether_addr() instead of ether_addr_equal()
to check if the ethernet address is all zeros.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230808081023.2303423-1-ruanjinjie@huawei.com
In 'mwifiex_process_sta_txpd()' and 'mwifiex_process_uap_txpd()',
replace 'BUG_ON()' with runtime check, and move all these checks
to 'mwifiex_process_tx()'. This way, both callees may be converted
to 'void', and the caller may be simplified as well.
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230802160726.85545-5-dmantipov@yandex.ru
Return -1 on possible 'mwifiex_write_reg()' errors in
'mwifiex_init_sdio_ioport()', do not ignore the value
returned by the latter in 'mwifiex_init_sdio()' and
'mwifiex_sdio_up_dev()' as well.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230802160726.85545-4-dmantipov@yandex.ru
Return -EINVAL on possible 'sscanf()' errors in
'mwifiex_regrdwr_write()' and 'mwifiex_rdeeprom_write()'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230802160726.85545-3-dmantipov@yandex.ru
Drop unused fields 'status_code' of 'struct mwifiex_txinfo',
'dfs_chan_switch_timer', 'sleep_params' (including related data
type 'struct mwifiex_sleep_params') of 'struct mwifiex_adapter',
adjust related code.
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230802160726.85545-2-dmantipov@yandex.ru
Add missing 'kfree_skb()' in 'mwifiex_init_rxq_ring()' and never do
'kfree(card->rxbd_ring_vbase)' because this area is DMAed and should
be released with 'dma_free_coherent()'. The latter is performed in
'mwifiex_pcie_delete_rxbd_ring()', which is now called to recover
from possible errors in 'mwifiex_pcie_create_rxbd_ring()'. Likewise
for 'mwifiex_pcie_init_evt_ring()', 'kfree(card->evtbd_ring_vbase)'
'mwifiex_pcie_delete_evtbd_ring()' and 'mwifiex_pcie_create_rxbd_ring()'.
Fixes: d930faee14 ("mwifiex: add support for Marvell pcie8766 chipset")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230731074334.56463-1-dmantipov@yandex.ru
Make sure mwifiex_process_mgmt_packet,
mwifiex_process_sta_rx_packet and mwifiex_process_uap_rx_packet,
mwifiex_uap_queue_bridged_pkt and mwifiex_process_rx_packet
not out-of-bounds access the skb->data buffer.
Fixes: 2dbaf751b1 ("mwifiex: report received management frames to cfg80211")
Signed-off-by: Polaris Pi <pinkperfect2021@gmail.com>
Reviewed-by: Matthew Wang <matthewmwang@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230723070741.1544662-1-pinkperfect2021@gmail.com
Allow moving the wiphy device for mwififex to a non-inital network
namespace. Many wireless drivers enable this flag implicitly by
initializing through the generic ieee80211_alloc_hw_nm function. As
mwifiex does not utilize this function WIPHY_FLAG_NETNS_OK must be set
explicitly.
Moving to network namespace and working connection tested using
wpa_supplicant from a network namespace as well as from a container on
GyroidOS. The hardware was the Toradex Apalis i.MX8QM Board using the
Azurewave AW-CM276NF wireless module.
Signed-off-by: Johannes Wiesboeck <johannes.wiesboeck@aisec.fraunhofer.de>
Reviewed-by: Michael Weiß <michael.weiss@aisec.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230706093437.3380526-1-johannes.wiesboeck@aisec.fraunhofer.de
When compiling with gcc 13.1 and CONFIG_FORTIFY_SOURCE=y,
I've noticed the following:
In function ‘fortify_memcpy_chk’,
inlined from ‘mwifiex_construct_tdls_action_frame’ at drivers/net/wireless/marvell/mwifiex/tdls.c:765:3,
inlined from ‘mwifiex_send_tdls_action_frame’ at drivers/net/wireless/marvell/mwifiex/tdls.c:856:6:
./include/linux/fortify-string.h:529:25: warning: call to ‘__read_overflow2_field’
declared with attribute warning: detected read beyond size of field (2nd parameter);
maybe use struct_group()? [-Wattribute-warning]
529 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The compiler actually complains on:
memmove(pos + ETH_ALEN, &mgmt->u.action.category,
sizeof(mgmt->u.action.u.tdls_discover_resp));
and it happens because the fortification logic interprets this
as an attempt to overread 1-byte 'u.action.category' member of
'struct ieee80211_mgmt'. To silence this warning, it's enough
to pass an address of 'u.action' itself instead of an address
of its first member.
This also fixes an improper usage of 'sizeof()'. Since 'skb' is
extended with 'sizeof(mgmt->u.action.u.tdls_discover_resp) + 1'
bytes (where 1 is actually 'sizeof(mgmt->u.action.category)'),
I assume that the same number of bytes should be copied.
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230629085115.180499-2-dmantipov@yandex.ru
Prefer 'strscpy()' over 'strlcpy()' in 'mwifiex_init_hw_fw()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230629085115.180499-1-dmantipov@yandex.ru
Core
----
- Rework the sendpage & splice implementations. Instead of feeding
data into sockets page by page extend sendmsg handlers to support
taking a reference on the data, controlled by a new flag called
MSG_SPLICE_PAGES. Rework the handling of unexpected-end-of-file
to invoke an additional callback instead of trying to predict what
the right combination of MORE/NOTLAST flags is.
Remove the MSG_SENDPAGE_NOTLAST flag completely.
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid.
- Enable socket busy polling with CONFIG_RT.
- Improve reliability and efficiency of reporting for ref_tracker.
- Auto-generate a user space C library for various Netlink families.
Protocols
---------
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2].
- Use per-VMA locking for "page-flipping" TCP receive zerocopy.
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags.
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative.
- Create a new MPTCP getsockopt to retrieve all info (MPTCP_FULL_INFO).
- Avoid waking up applications using TLS sockets until we have
a full record.
- Allow using kernel memory for protocol ioctl callbacks, paving
the way to issuing ioctls over io_uring.
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address.
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch.
- PPPoE: make number of hash bits configurable.
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig).
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge).
- Support matching on Connectivity Fault Management (CFM) packets.
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug.
- HSR: don't enable promiscuous mode if device offloads the proto.
- Support active scanning in IEEE 802.15.4.
- Continue work on Multi-Link Operation for WiFi 7.
BPF
---
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used,
or in fact passing the verifier at all for complex programs,
especially those using open-coded iterators.
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what
the output buffer *should* be, without writing anything.
- Accept dynptr memory as memory arguments passed to helpers.
- Add routing table ID to bpf_fib_lookup BPF helper.
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands.
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only).
- Show target_{obj,btf}_id in tracing link fdinfo.
- Addition of several new kfuncs (most of the names are self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter
---------
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value.
- Increase ip_vs_conn_tab_bits range for 64BIT builds.
- Allow updating size of a set.
- Improve NAT tuple selection when connection is closing.
Driver API
----------
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out).
- Support configuring rate selection pins of SFP modules.
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines.
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer.
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio).
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message.
- Split devlink instance and devlink port operations.
New hardware / drivers
----------------------
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers
-------
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is
a variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split
the different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and
Enhanced MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9i4I
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.
Core:
- Rework the sendpage & splice implementations
Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES
Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is
Remove the MSG_SENDPAGE_NOTLAST flag completely
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid
- Enable socket busy polling with CONFIG_RT
- Improve reliability and efficiency of reporting for ref_tracker
- Auto-generate a user space C library for various Netlink families
Protocols:
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]
- Use per-VMA locking for "page-flipping" TCP receive zerocopy
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative
- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)
- Avoid waking up applications using TLS sockets until we have a full
record
- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch
- PPPoE: make number of hash bits configurable
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)
- Support matching on Connectivity Fault Management (CFM) packets
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug
- HSR: don't enable promiscuous mode if device offloads the proto
- Support active scanning in IEEE 802.15.4
- Continue work on Multi-Link Operation for WiFi 7
BPF:
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything
- Accept dynptr memory as memory arguments passed to helpers
- Add routing table ID to bpf_fib_lookup BPF helper
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)
- Show target_{obj,btf}_id in tracing link fdinfo
- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter:
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value
- Increase ip_vs_conn_tab_bits range for 64BIT builds
- Allow updating size of a set
- Improve NAT tuple selection when connection is closing
Driver API:
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)
- Support configuring rate selection pins of SFP modules
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message
- Split devlink instance and devlink port operations
New hardware / drivers:
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers:
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"
* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...
For multi-link operation(MLO) TDLS management
frames need to be transmitted on a specific link.
The TDLS setup request will add BSSID along with
peer address and userspace will pass the link-id
based on BSSID value to the driver(or mac80211).
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616094948.cb3d87c22812.Ia3d15ac4a9a182145bf2d418bcb3ddf4539cd0a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These workqueues only host a single work item and thus doen't need explicit
concurrency limit. Let's use the default @max_active. This doesn't cost
anything and clearly expresses that @max_active doesn't matter.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi017@gmail.com>
Cc: Sharvari Harisangam <sharvari.harisangam@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
The type of "mwifiex_adapter->nd_info" is "struct cfg80211_wowlan_nd_info",
not "struct cfg80211_wowlan_nd_match".
Use struct_size() to ease the computation of the needed size.
The current code over-allocates some memory, so is safe.
But it wastes 32 bytes.
Fixes: 7d7f07d8c5 ("mwifiex: add wowlan net-detect support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7a6074fb056d2181e058a3cc6048d8155c20aec7.1683371982.git.christophe.jaillet@wanadoo.fr
mwifiex_wmm_list_len() is the same as list_count_nodes(), so use the latter
instead of hand writing it.
Turn 'ba_stream_num' and 'ba_stream_max' in size_t to keep the same type
as what is returned by list_count_nodes().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e77ed7f719787cb8836a93b6a6972f4147e40bc6.1682537509.git.christophe.jaillet@wanadoo.fr
clang with W=1 reports
drivers/net/wireless/marvell/mwifiex/11h.c:198:6: error: variable
'evt_buf' set but not used [-Werror,-Wunused-but-set-variable]
u8 *evt_buf;
^
This variable is not used so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230329131444.1809018-1-trix@redhat.com
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/net/wireless/marvell/mwifiex/sdio.c:498:34: error: ‘mwifiex_sdio_of_match_table’ defined but not used [-Werror=unused-const-variable=]
drivers/net/wireless/marvell/mwifiex/pcie.c:175:34: error: ‘mwifiex_pcie_of_match_table’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230312132523.352182-1-krzysztof.kozlowski@linaro.org
The current mac80211 mesh A-MSDU receive path fails to parse A-MSDU packets
on mesh interfaces, because it assumes that the Mesh Control field is always
directly after the 802.11 header.
802.11-2020 9.3.2.2.2 Figure 9-70 shows that the Mesh Control field is
actually part of the A-MSDU subframe header.
This makes more sense, since it allows packets for multiple different
destinations to be included in the same A-MSDU, as long as RA and TID are
still the same.
Another issue is the fact that the A-MSDU subframe length field was apparently
accidentally defined as little-endian in the standard.
In order to fix this, the mesh forwarding path needs happen at a different
point in the receive path.
ieee80211_data_to_8023_exthdr is changed to ignore the mesh control field
and leave it in after the ethernet header. This also affects the source/dest
MAC address fields, which now in the case of mesh point to the mesh SA/DA.
ieee80211_amsdu_to_8023s is changed to deal with the endian difference and
to add the Mesh Control length to the subframe length, since it's not covered
by the MSDU length field.
With these changes, the mac80211 will get the same packet structure for
converted regular data packets and unpacked A-MSDU subframes.
The mesh forwarding checks are now only performed after the A-MSDU decap.
For locally received packets, the Mesh Control header is stripped away.
For forwarded packets, a new 802.11 header gets added.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-4-nbd@nbd.name
[fix fortify build error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code re-uses "i" to be the iterator for both the inside and outside
loops. It means the outside loop will exit earlier than intended.
Fixes: d219b7eb37 ("mwifiex: handle BT coex event to adjust Rx BA window size")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/Y+ERnaDaZD7RtLvX@kili
One-element arrays are deprecated, and we are replacing them with flexible
array members instead. So, replace one-element array with flexible-array
member in struct mwifiex_ie_types_rates_param_set.
These are the only binary differences I see after the change:
mwifiex.o
_@@ -50154,7 +50154,7 @@
23514: R_X86_64_32S kmalloc_caches+0x50
23518: call 2351d <mwifiex_scan_networks+0x11d>
23519: R_X86_64_PLT32 __tsan_read8-0x4
- 2351d: mov $0x225,%edx
+ 2351d: mov $0x224,%edx
23522: mov $0xdc0,%esi
23527: mov 0x0(%rip),%rdi # 2352e <mwifiex_scan_networks+0x12e>
2352a: R_X86_64_PC32 kmalloc_caches+0x4c
scan.o
_@@ -5582,7 +5582,7 @@
4394: R_X86_64_32S kmalloc_caches+0x50
4398: call 439d <mwifiex_scan_networks+0x11d>
4399: R_X86_64_PLT32 __tsan_read8-0x4
- 439d: mov $0x225,%edx
+ 439d: mov $0x224,%edx
43a2: mov $0xdc0,%esi
43a7: mov 0x0(%rip),%rdi # 43ae <mwifiex_scan_networks+0x12e>
43aa: R_X86_64_PC32 kmalloc_caches+0x4c
and the reason for that is the following line:
drivers/net/wireless/marvell/mwifiex/scan.c:
1517 scan_cfg_out = kzalloc(sizeof(union mwifiex_scan_cmd_config_tlv),
1518 GFP_KERNEL);
sizeof(union mwifiex_scan_cmd_config_tlv) is now one-byte smaller due to the
flex-array transformation:
46 union mwifiex_scan_cmd_config_tlv {
47 /* Scan configuration (variable length) */
48 struct mwifiex_scan_cmd_config config;
49 /* Max allocated block */
50 u8 config_alloc_buf[MAX_SCAN_CFG_ALLOC];
51 };
Notice that MAX_SCAN_CFG_ALLOC is defined in terms of
sizeof(struct mwifiex_ie_types_rates_param_set), see:
26 /* Memory needed to store supported rate */
27 #define RATE_TLV_MAX_SIZE (sizeof(struct mwifiex_ie_types_rates_param_set) \
28 + HOSTCMD_SUPPORTED_RATES)
37 /* Maximum memory needed for a mwifiex_scan_cmd_config with all TLVs at max */
38 #define MAX_SCAN_CFG_ALLOC (sizeof(struct mwifiex_scan_cmd_config) \
39 + sizeof(struct mwifiex_ie_types_num_probes) \
40 + sizeof(struct mwifiex_ie_types_htcap) \
41 + CHAN_TLV_MAX_SIZE \
42 + RATE_TLV_MAX_SIZE \
43 + WILDCARD_SSID_TLV_MAX_SIZE)
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/252
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/Y9xkjXeElSEQ0FPY@work
One-element arrays are deprecated, and we are replacing them with flexible
array members instead. So, replace one-element arrays with flexible-array
members in multiple structures.
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
This results in no differences in binary output.
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/256
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/Y9xkECG3uTZ6T1dN@work
The Marvell SD8978 (aka NXP IW416) uses identical registers as SD8987,
so reuse the existing mwifiex_reg_sd8987 definition.
Note that mwifiex_reg_sd8977 and mwifiex_reg_sd8997 are likewise
identical, save for the fw_dump_ctrl register: They define it as 0xf0
whereas mwifiex_reg_sd8987 defines it as 0xf9. I've verified that
0xf9 is the correct value on SD8978. NXP's out-of-tree driver uses
0xf9 for all of them, so there's a chance that 0xf0 is not correct
in the mwifiex_reg_sd8977 and mwifiex_reg_sd8997 definitions. I cannot
test that for lack of hardware, hence am leaving it as is.
NXP has only released a firmware which runs Bluetooth over UART.
Perhaps Bluetooth over SDIO is unsupported by this chipset.
Consequently, only an "sdiouart" firmware image is referenced, not an
alternative "sdsd" image.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/536b4f17a72ca460ad1b07045757043fb0778988.1674827105.git.lukas@wunner.de
Commit e3fffc1f0b ("devicetree: document new marvell-8xxx and
pwrseq-sd8787 options") documented a compatible string for SD8787 in
the devicetree bindings, but neglected to add it to the mwifiex driver.
Fixes: e3fffc1f0b ("devicetree: document new marvell-8xxx and pwrseq-sd8787 options")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.11+
Cc: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/320de5005ff3b8fd76be2d2b859fd021689c3681.1674827105.git.lukas@wunner.de
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
strtobool() is the same as kstrtobool().
However, the latter is more used within the kernel.
In order to remove strtobool() and slightly simplify kstrtox.h, switch to
the other function name.
While at it, include the corresponding header file (<linux/kstrtox.h>)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1ff34549af5ad6f7c80d5b9e11872b5499065fc1.1667336095.git.christophe.jaillet@wanadoo.fr
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
There are sleep in atomic context bugs when uploading device dump
data in mwifiex. The root cause is that dev_coredumpv could not
be used in atomic contexts, because it calls dev_set_name which
include operations that may sleep. The call tree shows execution
paths that could lead to bugs:
(Interrupt context)
fw_dump_timer_fn
mwifiex_upload_device_dump
dev_coredumpv(..., GFP_KERNEL)
dev_coredumpm()
kzalloc(sizeof(*devcd), gfp); //may sleep
dev_set_name
kobject_set_name_vargs
kvasprintf_const(GFP_KERNEL, ...); //may sleep
kstrdup(s, GFP_KERNEL); //may sleep
The corresponding fail log is shown below:
[ 135.275938] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[ 135.281029] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265
...
[ 135.293613] Call Trace:
[ 135.293613] <IRQ>
[ 135.293613] dump_stack_lvl+0x57/0x7d
[ 135.293613] __might_resched.cold+0x138/0x173
[ 135.293613] ? dev_coredumpm+0xca/0x2e0
[ 135.293613] kmem_cache_alloc_trace+0x189/0x1f0
[ 135.293613] ? devcd_match_failing+0x30/0x30
[ 135.293613] dev_coredumpm+0xca/0x2e0
[ 135.293613] ? devcd_freev+0x10/0x10
[ 135.293613] dev_coredumpv+0x1c/0x20
[ 135.293613] ? devcd_match_failing+0x30/0x30
[ 135.293613] mwifiex_upload_device_dump+0x65/0xb0
[ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0
[ 135.293613] call_timer_fn+0x122/0x3d0
[ 135.293613] ? msleep_interruptible+0xb0/0xb0
[ 135.293613] ? lock_downgrade+0x3c0/0x3c0
[ 135.293613] ? __next_timer_interrupt+0x13c/0x160
[ 135.293613] ? lockdep_hardirqs_on_prepare+0xe/0x220
[ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0
[ 135.293613] __run_timers.part.0+0x3f8/0x540
[ 135.293613] ? call_timer_fn+0x3d0/0x3d0
[ 135.293613] ? arch_restore_msi_irqs+0x10/0x10
[ 135.293613] ? lapic_next_event+0x31/0x40
[ 135.293613] run_timer_softirq+0x4f/0xb0
[ 135.293613] __do_softirq+0x1c2/0x651
...
[ 135.293613] RIP: 0010:default_idle+0xb/0x10
[ 135.293613] RSP: 0018:ffff888006317e68 EFLAGS: 00000246
[ 135.293613] RAX: ffffffff82ad8d10 RBX: ffff888006301cc0 RCX: ffffffff82ac90e1
[ 135.293613] RDX: ffffed100d9ff1b4 RSI: ffffffff831ad140 RDI: ffffffff82ad8f20
[ 135.293613] RBP: 0000000000000003 R08: 0000000000000000 R09: ffff88806cff8d9b
[ 135.293613] R10: ffffed100d9ff1b3 R11: 0000000000000001 R12: ffffffff84593410
[ 135.293613] R13: 0000000000000000 R14: 0000000000000000 R15: 1ffff11000c62fd2
...
[ 135.389205] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end
This patch uses delayed work to replace timer and moves the operations
that may sleep into a delayed work in order to mitigate bugs, it was
tested on Marvell 88W8801 chip whose port is usb and the firmware is
usb8801_uapsta.bin. The following is the result after using delayed
work to replace timer.
[ 134.936453] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[ 135.043344] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end
As we can see, there is no bug now.
Fixes: f5ecd02a8b ("mwifiex: device dump support for usb interface")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/5cfa5c473ff6d069cb67760ffa04a2f84ef450a8.1661252818.git.duoming@zju.edu.cn
These cause sparse warnings, and since the device generally
works in little endian we can assume the code is correct, so
just fix the casts accordingly. No binary changes on x86.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220904212910.3f72609a3825.If4048592701bf04981be1dab18eaaa339b2ea382@changeid
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
-----BEGIN PGP SIGNATURE-----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=J5Fc
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-08-26-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes berg says:
====================
Various updates:
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for various key operations on MLD by adding new parameter
link_id. Pass the link_id received from userspace to driver for add_key,
get_key, del_key, set_default_key, set_default_mgmt_key and
set_default_beacon_key to support configuring keys specific to each MLO
link. Userspace must not specify link ID for MLO pairwise key since it
is common for all the MLO links.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20220730052643.1959111-4-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
Eliminate the follow smatch warning:
drivers/net/wireless/marvell/mwifiex/pcie.c:3364 mwifiex_unregister_dev() warn: inconsistent indenting
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220615005316.9596-1-yang.lee@linux.alibaba.com
Put the link_station_parameters structure in the station_parameters
structure (and remove the station_parameters fields already existing
in link_station_parameters).
Now, for an MLD station, the default link is added together with
the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on the normalized pattern:
this software file (the file ) is distributed by nxp under the terms
of the gnu general public license version 2 june 1991 (the license )
you may use redistribute and/or modify this file in accordance with
the terms and conditions of the license a copy of which is available
by writing to the free software foundation inc 51 franklin street
fifth floor boston ma 02110-1301 usa or on the worldwide web at
http://www gnu org/licenses/old-licenses/gpl-2 0 txt the file is
distributed as-is without warranty of any kind and the implied
warranties of merchantability or fitness for a particular purpose are
expressly disclaimed the license provides additional details about
this warranty disclaimer
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
* wfx: silicon labs devices
* plfxlc: pureLiFi X, XL, XC devices
mac80211
* host based BSS color collision detection
* prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
* support TP-Link T2E devices
rtw89
* support firmware crash simulation
* preparation for 8852ce hardware support
ath11k
* Wake-on-WLAN support for QCA6390 and WCN6855
* device recovery (firmware restart) support for QCA6390 and WCN6855
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
wcn36xx
* support for transmit rate reporting to user space
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmJxS2sRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuNgwf9H2oxMKLKrlFoX1qHtNBwZuHS6IERhOkM
NI9DjS4MCyiUSbA5r3sWlpqXQeKIbG/05gUZ6Y0ircGFwnAGjZ6isPwo8pKFgbh5
QljXQjUTHbkshrXW8K+VGJxw4F1oiPlOGUDVdXPy2FLx5ZvBlaUV2rWQUzsWX9I0
EnrM6ygHBVejVYDe+JSkb1gzb/07xuZN410IJPuZTPKJfYiE0oGU3zpTbExFitaz
ObjfFUWqHrVue525WFAJ9Dbk8kYEKyMThr7rkkWekYJjujJLJo0qhEiZVZu0eEsk
Vq4PdKmQAqlgbShQ/3Mv8BRsSH2wy62+zKjPWL+8t4Gmm9DbLu+++A==
=T7Ii
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
- wfx: silicon labs devices
- plfxlc: pureLiFi X, XL, XC devices
mac80211
- host based BSS color collision detection
- prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
- support TP-Link T2E devices
rtw89
- support firmware crash simulation
- preparation for 8852ce hardware support
ath11k
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support for QCA6390 and WCN6855
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- support for WCN6750
wcn36xx
- support for transmit rate reporting to user space
* tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (228 commits)
rtw89: 8852c: rfk: add DPK
rtw89: 8852c: rfk: add IQK
rtw89: 8852c: rfk: add RX DCK
rtw89: 8852c: rfk: add RCK
rtw89: 8852c: rfk: add TSSI
rtw89: 8852c: rfk: add LCK
rtw89: 8852c: rfk: add DACK
rtw89: 8852c: rfk: add RFK tables
plfxlc: fix le16_to_cpu warning for beacon_interval
rtw88: remove a copy of the NAPI_POLL_WEIGHT define
carl9170: tx: fix an incorrect use of list iterator
wil6210: use NAPI_POLL_WEIGHT for napi budget
ath10k: remove a copy of the NAPI_POLL_WEIGHT define
ath11k: Add support for WCN6750 device
ath11k: Datapath changes to support WCN6750
ath11k: HAL changes to support WCN6750
ath11k: Add QMI changes for WCN6750
ath11k: Fetch device information via QMI for WCN6750
ath11k: Add register access logic for WCN6750
ath11k: Add HW params for WCN6750
...
====================
Link: https://lore.kernel.org/r/20220503153622.C1671C385A4@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With a recent change now it is possible to detect the strapping
option on SD8997, which allows to pick up a correct firmware
for either SDIO-SDIO or SDIO-UART.
This commit enables SDIO-UART firmware on SD8997.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220422090313.125857-3-andrejs.cainikovs@toradex.com
To make it unambiguous that mmc_hw_reset() is for cards and not for
controllers, we make the function argument mmc_card instead of mmc_host.
Also, all users are converted.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408080045.6497-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that
net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx)
is held during the function's execution.
mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not
hold that lock, therefore violating the assertion.
Add a lock around the call.
Disclaimer:
I am currently working on a static analyser to detect missing locks.
This was a reported case. I manually verified the report by looking
at the code, so that I do not send wrong information or patches.
After concluding that this seems to be a true positive, I created
this patch.
However, as I do not in fact have this particular hardware,
I was unable to test it.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220321225515.32113-1-dossche.niels@gmail.com
Don't populate the read-only array wmm_oui on the stack but
instead make it static const. Also makes the object code a little
smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220311225610.10895-1-colin.i.king@gmail.com
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi017@gmail.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Sharvari Harisangam <sharvari.harisangam@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Jia-Ju Bai <baijiaju1990@gmail.com>:
mwifiex_dequeue_tx_packet()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 1432 (Lock A)
mwifiex_send_addba()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 608 (Lock B)
mwifiex_process_sta_tx_pause()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 398 (Lock B)
mwifiex_update_ralist_tx_pause()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 941 (Lock A)
Similar report for mwifiex_process_uap_tx_pause().
While the locking expectations in this driver are a bit unclear, the
Fixed commit only intended to protect the sta_ptr, so we can drop the
lock as soon as we're done with it.
IIUC, this deadlock cannot actually happen, because command event
processing (which calls mwifiex_process_sta_tx_pause()) is
sequentialized with TX packet processing (e.g.,
mwifiex_dequeue_tx_packet()) via the main loop (mwifiex_main_process()).
But it's good not to leave this potential issue lurking.
Fixes: f0f7c2275f ("mwifiex: minor cleanups w/ sta_list_spinlock in cfg80211.c")
Cc: Douglas Anderson <dianders@chromium.org>
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Link: https://lore.kernel.org/linux-wireless/0e495b14-efbb-e0da-37bd-af6bd677ee2c@gmail.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YaV0pllJ5p/EuUat@google.com
The firmware of the 88W8897 PCIe+USB card sends those events very
unreliably, sometimes bluetooth together with 2.4ghz-wifi is used and no
COEX event comes in, and sometimes bluetooth is disabled but the
coexistance mode doesn't get disabled.
This means we sometimes end up capping the rx/tx window size while
bluetooth is not enabled anymore, artifically limiting wifi speeds even
though bluetooth is not being used.
Since we can't fix the firmware, let's just ignore those events on the
88W8897 device. From some Wireshark capture sessions it seems that the
Windows driver also doesn't change the rx/tx window sizes when bluetooth
gets enabled or disabled, so this is fairly consistent with the Windows
driver.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103205827.14559-1-verdre@v0yd.nl
We assume at a few places that priv->version_str is 0-terminated, but
right now we trust the firmware that this is the case with the version
string we get from it.
Let's rather ensure this ourselves and replace the last character with
'\0'.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-4-verdre@v0yd.nl
The 88W8897 PCIe+USB card in the hardware revision 20 apparently has a
hardware issue where the card wakes up from deep sleep randomly and very
often, somewhat depending on the card activity, maybe the hardware has a
floating wakeup pin or something. This was found by comparing two MS
Surface Book 2 devices, where one devices wifi card experienced spurious
wakeups, while the other one didn't.
Those continuous wakeups prevent the card from entering host sleep when
the computer suspends. And because the host won't answer to events from
the card anymore while it's suspended, the firmwares internal power
saving state machine seems to get confused and the card can't sleep
anymore at all after that.
Since we can't work around that hardware bug in the firmware, let's
get the hardware revision string from the firmware and match it with
known bad revisions. Then disable auto deep sleep for those revisions,
which makes sure we no longer get those spurious wakeups.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-3-verdre@v0yd.nl
Since the version string we get from the firmware is always 128
characters long, use a define for this size instead of having the number
128 copied all over the place.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-2-verdre@v0yd.nl
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
Attached is the panic report from fuzzing.
skbuff: skb_over_panic: text:000000003bf1b5fa
len:2048 put:4 head:00000000dd6a115b data:000000000a9445d8
tail:0x844 end:0x840 dev:<NULL>
kernel BUG at net/core/skbuff.c:109!
invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 PID: 198 Comm: in:imklog Not tainted 5.6.0 #60
RIP: 0010:skb_panic+0x15f/0x161
Call Trace:
<IRQ>
? mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
skb_put.cold+0x24/0x24
mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YX4CqjfRcTa6bVL+@Zekuns-MBP-16.fios-router.home
