Device startup changed in Bz, some register bits moved around.
Change the code accordingly.
The new Bz hardware changes also the way we wake it (grab NIC
access) and the way we disable bus mastering, update the driver
code accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802215208.00a137364a95.I059a2abac948965458862941ee7db6a2e1076fa6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware crashes while we're waiting for the reset
handshake then it cannot possibly make progress anymore,
and we will just time out the wait. That's pointless, so
just stop waiting at that point.
Additionally, if it never acknowledges the reset handshake,
something went wrong.
Dump an error in both of these cases, but we need to do it
synchronously here since the device will be turned off.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.8b6a33544b4b.I55f97f70f8efa64db064a9207177a094c60ac8f1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When switching op-modes, or more generally when reconfiguring,
we might switch the RB size. In _iwl_pcie_rx_init() we have a
comment saying we must free all RBs since we might switch the
size, but this is actually too late: the switch has been done
and we'll free the buffers with the wrong size.
Fix this by always freeing the buffers, if any, at the start
of configure, instead of only after the size may have changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.42d7c93279c4.I07f74e65aab0e3d965a81206fcb289dc92d74878@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On 64-bit machines, struct iwl_rx_mem_buffer has a lot of
padding due to the use of pointers after the small items.
Move the list entry before them, and while at it also add
documentation for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.6a62255b3df0.I47bb36530a3c2cdbd73454c796ce608ee2a32a6c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new feature allows OEMs to set a special reduced power table in a
UEFI variable, which we use to tell the firmware to change the TX
power tables.
Read the variable and store it in a dram block to pass it to the
firmware. We do this as part of the PNVM loading flow.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210621103449.259a33ba5074.I2e0bb142d2a9c412547cba89b62dd077b328fdc4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In gen3, after firmware is alive, we no longer need the
firmware and image loader images, only the context info
itself and PRPH info/scratch need to remain.
Call iwl_pcie_ctxt_info_gen3_free() appropriately in the
alive callback (iwl_trans_pcie_gen2_fw_alive()) with a new
argument indicating whether it can free everything or only
partially.
The context info and PRPH scratch are also not needed after
PNVM load, but we don't have a good hook for freeing after
that, so keep them for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.8230d91a46c1.Ia7db71e5e6265ca87363f1481eac1bc3bbebb15c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After firmware alive, iwl_trans_pcie_gen2_fw_alive() is called
to free the context info. However, on gen3 that will then free
the context info with the wrong size.
Since we free this allocation later, let it stick around until
the device is stopped for now, freeing some of it earlier is a
separate change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.afb63fb8cbc1.If4968db8e09f4ce2a1d27a6d750bca3d132d7d70@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The TR/CR tail data are meant to be per-queue-arrays, however,
we allocate them completely wrong (we have a separate allocation
per queue).
Looking at this more closely, it turns out that the hardware
never uses these - we have a separate free list per RX queue
and maintain a write pointer for that in a register, and the
RX itself is indicated in the RB status (rb_stts) DMA region.
Despite nothing using the tail pointers, the hardware will
unconditionally access them to write updates, even when we aren't
using CRs/TRs.
Give it dummy values that we never use/update so it can do that
without causing trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617110647.5f5764e04c46.I4d5de1929be048085767f1234a1e07b517ab6a2d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
pcim_iomap_table() might return NULL, so we shouldn't unconditionally
dereference the return value by taking the [0] entry.
Handle this better by checking for NULL first, and then separately
checking if the [0] entry is NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210612142637.9aa4f0e3574a.I458b283f203d5f927f00be1bfbd4b8ebf11c5ae4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Analogically to what we did in 2800aadc18 ("iwlwifi: Fix softirq/hardirq
disabling in iwl_pcie_enqueue_hcmd()"), we must apply the same fix to
iwl_pcie_gen2_enqueue_hcmd(), as it's being called from exactly the same
contexts.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2104171112390.18270@cbobk.fhfr.pm
After the fix from Jiri that disabled local IRQs instead of
just BHs (necessary to fix an issue with submitting a command
with IRQs already disabled), there was still a situation in
which we could deep in there enable BHs, if the device config
sets the apmg_wake_up_wa configuration, which is true on all
7000 series devices.
To fix that, but not require reverting commit 1ed08f6fb5
("iwlwifi: remove flags argument for nic_access"), split up
nic access into a version with BH manipulation to use most
of the time, and without it for this specific case where the
local IRQs are already disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210415164821.d0f2edda1651.I75f762e0bed38914d1300ea198b86dd449b4b206@changeid
In a few PCIe devices we may have to swap out the configuration
after we allocate/initialise some parts of the device because
we only know the correct one after reading some registers. This
causes some things such as the byte-count table allocations to
be incorrect, since the configuration is swapped for one with a
bigger queue size.
Fix this by initialising most of the transport much later, only
after the configuration has finally been determined.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.8f5db97db1e4.Ic622da559b586a04ca536a0ec49ed5ecf03a9354@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The only difference between iwl_pcie_napi_poll_msix_shared() and
iwl_pcie_napi_poll_msix() is when we have a shared queue and nothing
in the rx queue. This case doesn't affect CPU performance, so we can
merge the two functions.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.9d1b61ef53a5.I60b33d5379cf7c12f1de30fc3fd4cefc38220141@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case the device is stopped any usage of hw queues needs to be
reallocated in fw due to fw reset after device stop, so all driver
internal queue should also be freed, and if we don't free the next usage
would leak the old memory and get in recover flows
"iwlwifi 0000:00:03.0: dma_pool_destroy iwlwifi:bc" warning.
Also warn about trying to reuse an internal allocated queue.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.c72d2f0355c4.Ia3baff633b9b9109f88ab379ef0303aa152c16bf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Debug message "firmware didn't ACK the reset - continue anyway\n"
in fw_reset_handshake() is classified as error, however this is not
an error as it is ignored. So, change it to info message for proper
classification of debug messages.
Signed-off-by: Ravi Darsi <ravi.darsi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.449b3092c330.I515edcc41913ca7fbe4a4de923671d120d5618c6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we (for example) have a trans_cfg entry in the PCI IDs table,
but then don't find a full cfg entry for it in the info table,
we fall through to the code that treats the PCI ID table entry
as a full cfg entry. This obviously causes crashes later, e.g.
when trying to build the firmware name string.
Avoid such crashes by using the low bit of the pointer as a tag
for trans_cfg entries (automatically using a macro that checks
the type when assigning) and then checking that before trying to
use the data as a full entry - if it's just a partial entry at
that point, fail.
Since we're adding some macro magic, also check that the type is
in fact either struct iwl_cfg_trans_params or struct iwl_cfg,
failing compilation ("initializer element is not constant") if
it isn't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.6f69fe6e4128.I921d4ae20ef5276716baeeeda0b001cf25b9b968@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For simplicity we assume that msix has 2 IRQ lines one used for rx data
called msix_non_share, and another used for one bit flags messages
(alive, hw error, sw error, rx data flag) called msix_share.
Every time the FW has data to send it puts it on the RX queue and HW
turns on the flags in msix_share (inta_fw) indicating about rx data,
and HW sends an interrupt a bit later to the msix_non_share _unless_
the msix_shared RX data bit was cleared.
Currently in the code every time we get an msix_shared we clear all bits
including rx data queue bits.
So we can have a race
----------------------------------------------------
DRIVER | HW | FW
----------------------------------------------------
- send host cmd to FW | |
| | - handle message
| | and put a response
| | on the RX queue
| - RX flag on |
| | - send alive msix
| - alive flag on |
| - interrupt |
| msix_share driver |
- handle msix_shared | |
and clear all flags | |
bits | |
| - don't send an |
| interrupt on |
| msix_non_shared |
| (driver cleared) |
- driver timeout on | |
waiting for host cmd | |
respond | |
| |
----------------------------------------------------
The change is to clear only the msi_shared flags that are handled in
the msix_shared flow, which will cause the hardware to send an interrupt
on the msix_non_share line as well, when it has data.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.a1cdda2fa270.I02a82312679f4541f30bb8db8747a797dbb70ee7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for different combinations of Bz
and CRFs.
Note: As of now we do not know the exact values
for ltr_delay and xtal_latency, so for now use the
worst case scenario values until the actual values
are clarified.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.caac8d996532.I6a22d6decb106cd50d7954b19236b69d685dcc39@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently have a special, separate, code path to acquire NIC
access for the in-flight host-command workaround on 7000 series
hardware. However, the normal code path here has grown a number
of additional workarounds/semantics over time, such as reprobing
the device if things fail.
Rather than try to replicate any of this logic, call the normal
grab_nic_access logic for the workaround.
This changes the spinlock to _bh, but that's OK since it's just
redundant, we already have soft-IRQs disabled when we get here,
and so didn't (have to) do it again. Since it's only for commands
there's however no point in making the code more complex just to
not use _bh here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.d196fc6ffb23.Idc1ce3ce9fed9178beee7e5409bc669f79b06a0d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most devices don't set the apmg_wake_up_wa flag, so we don't do
anything for them. Avoid taking the spinlock for every command
unless the device needs this workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.1ab60af3f318.I51cc202f68a2a953223e70c3e8610343412961b6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As the context info gen3 code is only called for >=AX210 devices
(from iwl_trans_pcie_gen2_start_fw()) the code there to set LTR
on 22000 devices cannot actually do anything (22000 < AX210).
Fix this by moving the LTR code to iwl_trans_pcie_gen2_start_fw()
where it can handle both devices. This then requires that we kick
the firmware only after that rather than doing it from the context
info code.
Note that this again had a dead branch in gen3 code, which I've
removed here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: ed0022da8b ("iwlwifi: pcie: set LTR on more devices")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.675486178ed1.Ib61463aba6920645059e366dcdca4c4c77f0ff58@changeid
Randy reported an error on his randconfig builds:
ERROR: modpost: "iwl_so_trans_cfg" [drivers/net/wireless/intel/iwlwifi/iwlwifi.ko] undefined!
The problem was that when CONFIG_IWLMVM was disabled we were still accessing
iwl_so_trans_cfg. Fix it by moving IS_ENABLED() check before the access.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 930be4e76f ("iwlwifi: add support for SnJ with Jf devices")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1614236661-20274-1-git-send-email-kvalo@codeaurora.org
When the interface goes up, we have already loaded the PNVM during
init, so we don't load it anymore. But we still need to set the PNVM
values in the context so that the FW can load it again.
Call set_pnvm when the PNVM is already loaded and change the
trans_pcie implementation to accept a second call to set_pnvm when we
have already allocated and, in this case, only set the values without
allocating again.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 6972592850 ("iwlwifi: read and parse PNVM file")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210172142.622546a3566f.I659a8b9aa944d213c4ba446e142d74f3f6db9c64@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some new devices contain an extra bit in the CRF ID register to denote
that they support CDB. Add definitions and macros to be able to
support it and add the "NO_CDB" to all existing entired.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210142629.7b40184d9899.I3bb2cf9b9afb0457583f786dc52d4d1b1ad75ffc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remember that those pointers have been freed by setting them
to NULL. Otherwise, we'd keep rxq pointing to random memory
which would prevent us from trying to re-allocate the Rx
resources if we call rx_alloc again.
Also, propagate the allocation failure to the caller of
iwl_pcie_nic_init so that we won't go further in the
start flow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.996b400d2f1c.I630379c504644700322f57b259383ae0af8d1975@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The only thing we do touching the device in hard interrupt context
is, at most, writing an interrupt ACK register, which isn't racing
in with anything protected by the reg_lock.
Thus, avoid disabling interrupts here for potentially long periods
of time, particularly long periods have been observed with dumping
of firmware memory (leading to lockup warnings on some devices.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.da916ab91298.I064c3e7823b616647293ed97da98edefb9ce9435@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Check FW notification sizes for robustness;
* Improvements in the NAPI implementation;
* Implement a workaround for CCA-EXT;
* Add new FW API support;
* Fix a CSA bug;
* Implement PHY integration version parsing;
* A bit of refactoring;
* One more CSA bug fix, this time in the AP side;
* Support for new So devices and a bit of reorg;
* Per Platform Antenna Gain (PPAG) fixes and improvements;
* Improvements in the debug framework;
* Some other clean-ups and small fixes.
-----BEGIN PGP SIGNATURE-----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=c570
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
iwlwifi patches intended for v5.12
* Check FW notification sizes for robustness;
* Improvements in the NAPI implementation;
* Implement a workaround for CCA-EXT;
* Add new FW API support;
* Fix a CSA bug;
* Implement PHY integration version parsing;
* A bit of refactoring;
* One more CSA bug fix, this time in the AP side;
* Support for new So devices and a bit of reorg;
* Per Platform Antenna Gain (PPAG) fixes and improvements;
* Improvements in the debug framework;
* Some other clean-ups and small fixes.
# gpg: Signature made Fri 05 Feb 2021 12:04:21 PM EET using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
When Rx queues are configured during module init, NAPI is enabled
while the Rx queue lock is held. However, since softirqs are not
disabled, it is possible that and IRQ would fire and call
iwl_pcie_rx_handle() which would also try to acquire the Rx lock.
Prevent this by disabling softirqs during Rx queue configuration,
as part of module init flow.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.d206ac428823.Ia19339efb09f9d80143f0d0e398a158180754cfa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Handling host commands in a sync way is not directly related to PCIe
transport, and can serve as common logic for any transport, so move
it to trans layer.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.fde99af4e0f7.I4cab95919eb35cc5bfb26d32dcf5e15419d0e0ef@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
D3_CONFIG_CMD and D0I3_END_CMD should be the last\first
command upon suspend\resume correspondingly, otherwise,
FW will raise an assert (0x342).
There are firmware notifications that cause the driver to
send a command back to the firmware. If such a notification
is sent to the driver while the the driver prepares the
firmware for D3, operation, what is likely to happen is that
the handling of the notification will try to get the mutex
and will wait unil the driver finished configuring the
firmware for D3. Then the handling notification will get
the mutex and handle the notification which will lead to
the aforementioned ASSERT 342.
To avoid this, we need to prevent any command to be sent to
the firmware between the D3_CONFIG_CMD and the D0I3_END_CMD.
Check this in the utility layer that sends the host commands
and in the transport layer as well.
Flag the D3_CONFIG_CMD and the D0I3_END_CMD commands as
commands that must be sent even if the firmware has already
been configured for D3 operation.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.1935a993b471.I3192c93c030576ca16773c01b009c4d93610d6ea@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of pretending to have NAPI and then relying entirely on
interrupts anyway, properly implement NAPI and schedule the poll
when we get an interrupt, re-enabling the interrupt only after
the poll completed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.a5951ac4fc06.I9c84a147288fcfb1b019572c6758f2d92949f5d7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we spin for a long time in memory reads that (for some reason in
hardware) take a long time, then we'll eventually get messages such
as
watchdog: BUG: soft lockup - CPU#2 stuck for 24s! [kworker/2:2:272]
This is because the reading really does take a very long time, and
we don't schedule, so we're hogging the CPU with this task, at least
if CONFIG_PREEMPT is not set, e.g. with CONFIG_PREEMPT_VOLUNTARY=y.
Previously I misinterpreted the situation and thought that this was
only going to happen if we had interrupts disabled, and then fixed
this (which is good anyway, however), but that didn't always help;
looking at it again now I realized that the spin unlock will only
reschedule if CONFIG_PREEMPT is used.
In order to avoid this issue, change the code to cond_resched() if
we've been spinning for too long here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 04516706bb ("iwlwifi: pcie: limit memory read spin time")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130253.217a9d6a6a12.If964cb582ab0aaa94e81c4ff3b279eaafda0fd3f@changeid
There's no reason to use ktime_get() since we don't need any better
precision than jiffies, and since we no longer disable interrupts
around this code (when grabbing NIC access), jiffies will work fine.
Use jiffies instead of ktime_get().
This cleanup is preparation for the following patch "iwlwifi: pcie: reschedule
in long-running memory reads". The code gets simpler with the weird clock use
etc. removed before we add cond_resched().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130253.621c948b1fad.I3ee9f4bc4e74a0c9125d42fb7c35cd80df4698a1@changeid
To avoid completion timeouts during device boot, set up the
LTR timeouts on more devices - similar to what we had before
for AX210.
This also corrects the AX210 workaround to be done only on
discrete (non-integrated) devices, otherwise the registers
have no effect.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: edb625208d ("iwlwifi: pcie: set LTR to avoid completion timeout")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.fb819e19530b.I0396f82922db66426f52fbb70d32a29c8fd66951@changeid
If we erroneously try to set the PNVM data again after it has
already been set, we could leak the old DMA memory. Avoid that
and warn, we shouldn't be doing this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6972592850 ("iwlwifi: read and parse PNVM file")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.929c2d680429.I086b9490e6c005f3bcaa881b617e9f61908160f3@changeid
There are some races in the hardware that can possibly lead to
a bus lockup later during a restart when we manage to kill the
firmware at a bad time (while it's accessing the bus).
To work around this, add support for a new handshake between
firmware and driver to ensure that the firmware is in a well-
known state before we kill it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.7756fcc9865c.I13de65e0ffcb4186dd4c1a465f66df2e98c9a947@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need the sequence/index/cmd_index unless we're doing
reclaim, they're not even valid in the other cases. Move the
variables and their assignments into the right if statement
and combine the two if statements into a single one as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.6207fdcc91a9.Ia71e766ead7560262f4bc6ad3da6f1117c498cd6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We set this here, but don't really use it until we've
enabled interrupts. But when enabling interrupts we
always overwrite this value anyway, so remove setting
it here, mostly in order not to have some additional
code duplicated later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.135d96297aca.Id2d26fff60b6c31202bb0a36e46948bda6a39d33@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is actually wrong, the bit used here by the image loader
is BIT(1), not BIT(2). The latter will be reused by the new
reset flow soon.
However, as we never had any complaints about not printing
the IML status or not handling the IML error interrupt (and
I suspect the code handling it was incorrectly anyway) just
remove the code for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.9a323f4a3493.Ic7aee4dbbf4be42287c338c2fa1b111473724116@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If 12k A-MSDU size is requested, we will actually allocate 16k
due to page allocation. Thus, change it to actually mean 16k,
which is useful for certain sniffer use cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.84ae405829d4.I31184f4be31f7c3feb9a29aef3a111e70d15c64a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We no longer need code that was introduced to differentiate
between two early versions of 8260.
We can remove this convoluted way to get the hardware version
that was needed because of a bug in the register's
configuration.
Moreover, since we no longer need to access the PRPH
registers, we no longer need to wake up the device,
request ownership, etc...
Remove all that.
This allows us to get the rid of the obsolete comment
about the AUX bus MISC address space which should have
been moved when this code was moved away from here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.4a5665ccd8a6.Iff3879405c15758ba661c430e77dc2160ddada1c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On some platforms, the preset values aren't correct and then we may
get a completion timeout in the firmware. Change the LTR configuration
to avoid that. The firmware will do some more complex reinit of this
later, but for the boot process we use ~250usec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d83d591c05ba.I42885c9fb500bc08b9a4c07c4ff3d436cc7a3c84@changeid
When we read device memory, we lock a spinlock, write the address we
want to read from the device and then spin in a loop reading the data
in 32-bit quantities from another register.
As the description makes clear, this is rather inefficient, incurring
a PCIe bus transaction for every read. In a typical device today, we
want to read 786k SMEM if it crashes, leading to 192k register reads.
Occasionally, we've seen the whole loop take over 20 seconds and then
triggering the soft lockup detector.
Clearly, it is unreasonable to spin here for such extended periods of
time.
To fix this, break the loop down into an outer and an inner loop, and
break out of the inner loop if more than half a second elapsed. To
avoid too much overhead, check for that only every 128 reads, though
there's no particular reason for that number. Then, unlock and relock
to obtain NIC access again, reprogram the start address and continue.
This will keep (interrupt) latencies on the CPU down to a reasonable
time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201022165103.45878a7e49aa.I3b9b9c5a10002915072312ce75b68ed5b3dc6e14@changeid
The driver looks for a PNVM file that contains FW configuration data
for each different HW combination. The FW requests the data for a
certain SKU_ID and the driver tries to find it in the PNVM file.
Read the file, parse its contents and send it to the trans.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.826bc607e57a.I1d93dd6e6651586878db57fac3e7c3f09d742c42@changeid
We were using a very high latency for all 9560 devices so they all
would have time to stabilize. But this causes the system to be
slighly slower, so we can use the best values for each device.
This requires a new trans cfg struct for devices with longer latency
and some adjustments to the other structs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.34392f98fdb1.I3d3db14f6d1a8ecc547ca6afce8488816bd26081@changeid
To avoid duplicating code we need to call iwl_pcie_txq_update_byte_cnt_tbl
function from non bus independent code so make it bus independent.
Used spatch rule
@r1@
struct iwl_trans_pcie *trans_pcie;
@@
(
-trans_pcie->scd_bc_tbls
+trans->txqs.scd_bc_tbls
|
-iwl_pcie_txq_update_byte_cnt_tbl
+iwl_txq_gen1_update_byte_cnt_tbl
|
-iwl_pcie_txq_inval_byte_cnt_tbl
+iwl_txq_gen1_inval_byte_cnt_tbl
|
-iwl_pcie_tfd_unmap
+iwl_txq_gen1_tfd_unmap
|
-iwl_pcie_tfd_tb_get_addr
+iwl_txq_gen1_tfd_tb_get_addr
|
-iwl_pcie_tfd_tb_get_len
+iwl_txq_gen1_tfd_tb_get_len
|
-iwl_pcie_tfd_get_num_tbs
+iwl_txq_gen1_tfd_get_num_tbs
)
/* clean all new unused variables */
@ depends on r1@
type T;
identifier i;
expression E;
@@
- T i = E;
... when != i
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.8d33e791ec8c.Ica35125ed640aa3aa1ecc38fb5e8f1600caa8df6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is an issue in the HW DMA engine in the 9000 family of devices
when more than 6 RX queues are used. The issue is that the FW may
hang when IWL_MVM_RXQ_NSSN_SYNC notifications are sent.
Fix this by limiting the number of RX queues to 6 in the 9000 family
of devices.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.37d90f9ceb0c.I8dfe8a7d3a7ac9f0bc9d93e4a03f8165d8c999d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the regression introduced by commit c8685937d0 ("iwlwifi: move
pu devices to new table") by adding the ids and the configurations of
two missing Killer 1550 cards in order to configure and let them work
correctly again (following the new table convention).
Resolve bug 208141 ("Wireless ac 9560 not working kernel 5.7.2",
https://bugzilla.kernel.org/show_bug.cgi?id=208141).
Fixes: c8685937d0 ("iwlwifi: move pu devices to new table")
Signed-off-by: Alessio Bonfiglio <alessio.bonfiglio@mail.polimi.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200714091911.4442-1-alessio.bonfiglio@mail.polimi.it
We don't want to have txq code in the PCIe transport code, so move all
the relevant elements to a new iwl_txq structure and store it in
iwl_trans.
spatch
@ replace_pcie @
struct iwl_trans_pcie *trans_pcie;
@@
(
-trans_pcie->queue_stopped
+trans->txqs.queue_stopped
|
-trans_pcie->queue_used
+trans->txqs.queue_used
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->cmd_queue
+trans->txqs.cmd.q_id
|
-trans_pcie->cmd_fifo
+trans->txqs.cmd.fifo
|
-trans_pcie->cmd_q_wdg_timeout
+trans->txqs.cmd.wdg_timeout
)
// clean all new unused variables
@ depends on replace_pcie @
type T;
identifier i;
expression E;
@@
- T i = E;
... when != i
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.a428d3c9d66f.Ie04ae55f33954636a39c98e7ae1e739c0507435b@changeid
Newer firmware versions will parse a few extra bits in the
context info to be able to determine whether we are using
bigger than 4k RBs, indicate 8k/12k to them if we actually
use those (e.g. for sniffer based on the module parameter).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.f83f994572ca.Ibcfd66c3f9b69e68a53b3b2df8331ffb225db655@changeid
Second set of patches for v5.8. Lots of new features and new supported
hardware for mt76. Also rtw88 got new hardware support.
Major changes:
rtw88
* add support for Realtek 8723DE PCI adapter
* rename rtw88.ko/rtwpci.ko to rtw88_core.ko/rtw88_pci.ko
iwlwifi
* stop supporting swcrypto and bt_coex_active module parameters on
mvm devices
* enable A-AMSDU in low latency
mt76
* new devices for mt76x0/mt76x2
* support for non-offload firmware on mt7663
* hw/sched scan support for mt7663
* mt7615/mt7663 MSI support
* TDLS support
* mt7603/mt7615 rate control fixes
* new driver for mt7915
* wowlan support for mt7663
* suspend/resume support for mt7663
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJey69PAAoJEG4XJFUm622bIcEH/iT2M037SSfySAdykAvUQHJU
E1E9iZKJVVKZ+8nfTh03thtT4HyPC0jZMjWrqL5N4PFTKJKJo/t9HfAEq4niboGj
l2jeqQpujck7zUBKQh4HWWJiDtpOiMUS9noHSujnS4NThtRo/+/qxIiCz6nxVBix
DHKi+zZR4t05U3UYYivWc/CfojIXLrqeZl187MnDBV6LvNP8/en+HpmnCzp/trFn
qxBl2MWzr1oZf8j+t1UPtDVnUz1OMcHvnCQosQMeBwNtkkqKGc7Cip6VG/fqsLau
HdLwQWvsRByFT7yaXbwI+/uOMZhZ/KPWx9BdDdistegxyE8fZvjs/csfk7p3lSc=
=sKYR
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
Second set of patches for v5.8. Lots of new features and new supported
hardware for mt76. Also rtw88 got new hardware support.
Major changes:
rtw88
* add support for Realtek 8723DE PCI adapter
* rename rtw88.ko/rtwpci.ko to rtw88_core.ko/rtw88_pci.ko
iwlwifi
* stop supporting swcrypto and bt_coex_active module parameters on
mvm devices
* enable A-AMSDU in low latency
mt76
* new devices for mt76x0/mt76x2
* support for non-offload firmware on mt7663
* hw/sched scan support for mt7663
* mt7615/mt7663 MSI support
* TDLS support
* mt7603/mt7615 rate control fixes
* new driver for mt7915
* wowlan support for mt7663
* suspend/resume support for mt7663
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't really expect fragmented RBs, and don't seem to be seeing
them in practice since that would've caused a crash. Nevertheless,
we should be expecting the hardware to send them.
Parse the flag indicating a fragmented buffer, but then discard it
and any fragments thereof, at least for now. We need to do more
work in the higher layers to properly deal with this, since we may
not get "normal" firmware notifications that are fragmented, only
RX, and then we need to put it back together and add the necessary
API to report a chain of things to the higher layers, this doesn't
fit into the struct iwl_rx_cmd_buffer today.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.e78a59f70b1d.Ica656a98a4e4220d73edc97600edd680cbc97241@changeid
Since the recent patch in this area, we no longer allocate 64k
for a single queue, but only 1k, which still means a full page.
Use a DMA pool to reduce this further, since we will have a lot
of queues in a typical system that can share pages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.6e84c79aea30.Ie9a417132812d110ec1cc87852f101477c01cfcb@changeid
The hardware needs a byte-count table with the size of each frame
on the queue to build A-MPDUs, but:
* newer generation no longer have the duplicated space at the end,
they can deal with the wrap properly - and we don't even fill
the dup anyway
* we have a maximum queue size of 512 right now and don't use the
theoretical hardware maximum of 65536.
Together, this reduces the byte count table DMA allocation from
64KiB (65536*2 + 64*2 rounded up) to 1 KiB (though that might be
rounded up to a full 4 KiB page by the allocator, not sure it can
share the allocations.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.c263b787b5ab.I059507a9760b1ce1d45d84dcaa91629a5cfb58e0@changeid
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On newer hardware, the tx_queue debugfs file would need to
allocate 37.5kib data since there are 512 queues, which is
too much. Rather than resorting to kludges like kvmalloc(),
use the seq_file API to print out the data.
While at it, also fix a NULL pointer dereference here, the
txq pointer from trans_pcie->txqs[] may be NULL if that
queue hasn't been allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200417131727.491cf8224c49.I7f154d81e5becef3b5ff22d7c6e36170bde0d7d5@changeid
In the context info, we need to indicate the correct RB size
to the device so that it will not think we have 4k when we
only use 2k. This seems to not have caused any issues right
now, likely because the hardware no longer supports putting
multiple entries into a single RB, and practically all of
the entries should be smaller than 2k.
Nevertheless, it's a bug, and we must advertise the right
size to the device.
Note that right now we can only tell it 2k vs. 4k, so for
the cases where we have more, still use 4k. This needs to
be fixed by the firmware first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfdc20efeb ("iwlwifi: pcie: use partial pages if applicable")
Cc: stable@vger.kernel.org # v5.6
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.ae6cd345764f.I0985c55223decf70182b9ef1d8edf4179f537853@changeid
The iwl_trans_pcie_dyn_txq_free() function only releases the frames
that may be left on the queue by calling iwl_pcie_gen2_txq_unmap(),
but doesn't actually free the DMA ring or byte-count tables for the
queue. This leads to pretty large memory leaks (at least before my
queue size improvements), in particular in monitor/sniffer mode on
channel hopping since this happens on every channel change.
This was also now more evident after the move to a DMA pool for the
byte count tables, showing messages such as
BUG iwlwifi:bc (...): Objects remaining in iwlwifi:bc on __kmem_cache_shutdown()
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=206811.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6b35ff9157 ("iwlwifi: pcie: introduce a000 TX queues management")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.f5f4c4193ec1.Id5feebc9b4318041913a9c89fc1378bb5454292c@changeid
There's no need for this to be exposed outside of the tx.c
file, make it static.
Change-Id: I41d40008311b108d0578bd2ec73c5477e700a839
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't support the FPGA versions of this card combination anymore.
Remove the cfg mangling that tries to load it and all the relevant
structures.
Change-Id: I190652101afcab682cfba873d062992f11efca32
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A couple of SoCs, which can be recognized by PCI device IDs 0xA0F0 and
0x43F0, need a longer wait for the xtal to stabilize. To handle this,
add a new trans_cfg structure for Qu devices with a larger
xtal_latency value and apply them to the devices recognized by these
IDs. Also add a flag that allows us to inform the FW that the low
latency xtal should be used.
Change-Id: I8a14c6af45ea14d8e7f1ef38a589158f38d0c0ea
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we identify the correct cfgs with the new tables for Qu step
C and QuZ with Jf, we can remove the mangling we do later on.
Change-Id: Ic01ce67db147e897ad2424f0e05a70a00d2c620e
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the QnJ devices have a similar matching to the other Qu devices,
but needs a different configuration. Convert the QnJ devices to the
new table accordingly.
Change-Id: If236ef3d0da3e605a3379922818f5897e0affd7e
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new generic iwl_trans structures for these devices and apply the
correct cfg depending on the device characteristics.
Since we have to match Qu with IWL_CONFIG_ANY, we also need to move
the Hr devices to the new table, but for now we keep matching on PCI
device and subsystem device IDs.
Change-Id: I14e9146a99621ff11ce50bc746a4b88af508fee0
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to use different firmware versions for different HW steps with
certain devices. Prepare for this differentiation by adding HW step
to the new device table.
Change-Id: Ib1afb7b0c89e9dc2d26e6d32ea19e978c17ba1dd
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These values are selected based on the PCI device ID, so the decision
to use them can be made early. By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean). This will also allow us to make
more decisions based on, for instance, the SoC type in used.
The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.
Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl9560_2ac_cfg struct is used for PNJ devices and the
configuration is the same as iwl9260_2ac_cfg, so we can remove the
former to avoid redundancy.
Change-Id: I17ac1802f00bd80006930b922a9fc21df60e3c16
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the read_config32 op to allow dumping the config space when
needed.
Change-Id: Ib2d254a38a4bfb95dcc3d04eec91781827a0c623
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TH1 devices can now be fully differentiated by using the device
parameters we have (particularly the RF_TYPE). Start using these
parameters instead of hardcoding to specific subsystem device IDs.
This also fixes the name of one of the TH1 devices that was
erroneously using the 9260 struct and renames 9160 to 9162.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200309091348.18d4304b5454.Ib168d186da88393e9ec46f0fca523edb48d9138e@changeid
Devices that also include a GNSS module have different names, so add a
new device option to differentiate them, according to the values we
have in the modules section of the subsystem device ID.
Additionally, convert the two applicable devices to use this value
instead of hardcoded subsystem IDs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200309091348.1f958e558d05.I45492bb57cbbeb4cc0ec84313bade4def7377a27@changeid
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeLcWsAAoJEG4XJFUm622bDGUIAJuhM4LiDAzOGnDjH5cMosOC
/qwDpGD19cEeVAhNSMKUn7Uo9+qbQYIleiO7XXxzCuJceYbxbT5s3Vb/fWsRUPjS
cBDmGuK8/giqMQJshXvfCTsoF83CyirCjY/MJvomK2BRlXM8hQ3s6hAcfU0zQ96e
OU1akcfZzUwjaBKaDYLncxLuGbeUXMy8AZwFdgQlQRMoObpen/IIwx6jDK/A+3l6
VCOJF+JTkDytfNWmTpZ65uJrYEXoLe6G4028FjOI4BDFmEgvdHC5vTm7VOBhrkuB
9tsKcYNvECCNn2WI96V+etD8kaZPscQIW8hgOrYyGxw43lJg5zH4Z9eWAmHojxE=
=UOhb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
-----BEGIN PGP SIGNATURE-----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=Ovcw
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.6
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeKX2wAAoJEG4XJFUm622bG8QH/3+QXaSJAVqzbQh2boy7aS88
xhrrnh+bSqWY0ChMk0Z73RF8Ek0WlO+os4uN1cbWIWujrdQUPbTBtOwX4d0TzTue
E3tBFPiHTlVtU43z1bsprA+6EE7fqt/H2lWtlxk0IHzeiQY9NcB6BlDKKCzk5Hib
aMb5HCQy4JmSK83E60HLM9L4nEmEP+yveaKL7uaAZw+qkmyk2mT6um0TlmOYVoNG
9V6k3OZto8LvyV6jKPZgVI6QBATnwHDxlWgooYRj54PuCj9hTbR2mcuUL2QyQeze
AX2QNI+1kWIrAiDaU/lOj8579SiUl36iqtuKmtLhDnSe1GxDkrzmawtz3aGDm4k=
=VZox
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL
skbs") introduces batching of GRO_NORMAL packets in napi_frags_finish,
and commit 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") adds the same to napi_skb_finish. However,
dev_gro_receive (that is called just before napi_{frags,skb}_finish) can
also pass skbs to the networking stack: e.g., when the GRO session is
flushed, napi_gro_complete is called, which passes pp directly to
netif_receive_skb_internal, skipping napi->rx_list. It means that the
packet stored in pp will be handled by the stack earlier than the
packets that arrived before, but are still waiting in napi->rx_list. It
leads to TCP reorderings that can be observed in the TCPOFOQueue counter
in netstat.
This commit fixes the reordering issue by making napi_gro_complete also
use napi->rx_list, so that all packets going through GRO will keep their
order. In order to keep napi_gro_flush working properly, gro_normal_list
calls are moved after the flush to clear napi->rx_list.
iwlwifi calls napi_gro_flush directly and does the same thing that is
done by gro_normal_list, so the same change is applied there:
napi_gro_flush is moved to be before the flush of napi->rx_list.
A few other drivers also use napi_gro_flush (brocade/bna/bnad.c,
cortina/gemini.c, hisilicon/hns3/hns3_enet.c). The first two also use
napi_complete_done afterwards, which performs the gro_normal_list flush,
so they are fine. The latter calls napi_gro_receive right after
napi_gro_flush, so it can end up with non-empty napi->rx_list anyway.
Fixes: 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL skbs")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Cc: Alexander Lobakin <alobakin@dlink.ru>
Cc: Edward Cree <ecree@solarflare.com>
Acked-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a lot of mostly duplicated data structures that are repeated
only because the device name string is different. To avoid this, move
the string from the cfg to the trans structure and add it
independently from the rest of the configuration to the PCI mapping
tables.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new device table that contains information that can be checked
at runtime in order to decide which configuration to use. This allows
us to map the full cfg independently from the tran-specific
configuration.
This is the first step in creating the new table. Subsequent patches
will add the possibility of checking different values at runtime in
order to make the decision.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With the new concept of separating the trans-specific (trans_cfg) data
from the rest of the cfg, we will start mapping only the trans_cfg
part to the PCI device ID/subsystem device ID. So we can assume that
the data passed to the probe function contains the trans_cfg, but
since the full cfg still contains the trans_cfg at the beginning, we
can allow a full cfg to be passed as well. This makes it easier to
convert the existing tables one by one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
L0S states have been found to be unstable with our devices and in
newer hardware they are not supported at all, so we must always set
the L0S_DISABLED bit. Previously we were only disabling L0S states if
L1 was supported, because the assumption was that transitions from L0S
to L1 state was the problematic case. But now we should never use
L0S, so do it regardless of whether L1 is supported or not.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This bit has been misnamed since the initial implementation of the
driver. The correct semantics is that setting this bit disables L0S
states, and we already clearly use it as such in the code. Rename it
to avoid confusion.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We needed this abstraction for some CSR registers for
IWL_DEVICE_22560, but that has been removed, so we don't need the
abstraction anymore. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few configuration structures were either not referenced anymore or
assigned to devices IDs that were not in use anymore. Remove them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Validate that the queue ID is in range before trying to use it as
an index or for test_bit() - the previous bug showed that this has
in fact happened, and it was lucky that we caught it there, had the
bit been set then we'd have actually used the value despite being
far out of range.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have only 2k RBs like on the latest (AX210) hardware, then
even on x86 where PAGE_SIZE is 4k we currently waste half of the
memory.
If this is the case, return partial pages from the allocator and
track the offset in each RBD (to be able to find the data in them
and remap them later.)
This might also address other platforms with larger PAGE_SIZE by
putting more RBs into a single large page.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need to map *everything* of the RX buffers, we won't use
that much, map only the part we're going to use. This save some
IOMMU space (if applicable and it can deal with that) and also
prepares a bit for mapping partial pages for 2K buffers later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For HE-capable devices, we need to allocate more receive buffers as
there could be 256 frames aggregated into a single A-MPDU, and then
they might contain A-MSDUs as well. Until 22000 family, the devices
are able to put multiple frames into a single RB and the default RB
size is 4k, but starting from AX210 family this is no longer true.
On the other hand, those newer devices only use 2k receive buffers
(by default).
Modify the code and configuration to allocate an appropriate number
of RBs depending on the device capabilities:
* 4096 for AX210 HE devices, which use 2k buffers by default,
* 2048 for 22000 family devices which use 4k buffers by default,
* 512 for existing 9000 family devices, which doesn't really
change anything since that's the default before this patch,
* 512 also for AX210/22000 family devices that don't do HE.
Theoretically, for devices lower than AX210, we wouldn't have to
allocate that many RBs if the RB size was manually increased, but
to support that the code got more complex, and it didn't really
seem necessary as that's a use case for monitor mode only, where
hopefully the wasted memory isn't really much of a concern.
Note that AX210 devices actually support bigger than 12-bit VID,
which is required here as we want to allocate 4096 buffers plus
some for quick recycling, so adjust the code for that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After more investigation on the hardware side, it appears that the
hardware bug regarding 2^32 boundary reaching/crossing also affects
other uses of the DMA engine, in particular the ones triggered by
the context-info (image loader) mechanism.
It also turns out that the bug only affects devices with gen2 TX
hardware engine, so we don't need to change context info for gen3.
The TX path workarounds are simpler to still keep for both though.
Add the workaround to that code as well; this is a lot simpler as
we have just a single way to allocate DMA memory there.
I made the algorithm recursive (with a small limit) since it's
actually (almost) impossible to hit this today - dma_alloc_coherent
is currently documented to always return 32-bit addressable memory
regardless of the DMA mask for it, and so we could only get REALLY
unlucky to get the very last page in that area.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As noted in the previous commit, due to the way we allocate the
dev_cmd headers with 324 byte size, and 4/8 byte alignment, the
part we use of them (bytes 20..40-68) could still cross a page
and thus 2^32 boundary.
Address this by using alignment to ensure that the allocation
cannot cross a page boundary, on hardware that's affected. To
make that not cause more memory consumption, reduce the size of
the allocations to the necessary size - we go from 324 bytes in
each allocation to 60/68 on gen2 depending on family, and ~120
or so on gen1 (so on gen1 it's a pure reduction in size, since
we don't need alignment there).
To avoid size and clearing issues, add a new structure that's
just the header, and use kmem_cache_zalloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Warn if the DMA bug is going to happen. We don't have a good
way of actually aborting in this case and we have workarounds
in place for the cases where it happens, but in order to not
be surprised add a safety-check and warn.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a hardware bug in the flow handler (DMA engine), if the
address + len of some TB wraps around a 2^32 boundary, the carry
bit is then carried over into the next TB.
Work around this by copying the data to a new page when we find
this situation, and then copy it in a way that we cannot hit the
very end of the page.
To be able to free the new page again later we need to chain it
to the TSO page, use the last pointer there to make sure we can
never use the page fully for DMA, and thus cannot cause the same
overflow situation on this page.
This leaves a few potential places (where we didn't observe the
problem) unaddressed:
* The second TB could reach or cross the end of a page (and thus
2^32) due to the way we allocate the dev_cmd for the header
* For host commands, a similar thing could happen since they're
just kmalloc().
We'll address these in further commits.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the tracking that records the page in the SKB for later
free (refcount decrement) into the get_page_hdr() function
for better code reuse.
While at it, also add an assertion that this doesn't overwrite
any existing page pointer in the skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd+P4eAAoJEG4XJFUm622bnOQH/RHSFFQNjxfPboZoozKb0/mT
6YtrG+0K1z8E21Os2bd+s4aRJgq1oGKDocMie5y53M38qQ5N3FchzcGopNRCRy/a
gF1PzEqceOysbEtPOx4yI+c0Gfi7rS0SjEyf2XKGowXsoIZh4j+1xlWbF/JtHt6n
J901W1GW0ZUCHaP8KuZcbsS2nfdV8tFW2NQW3Xuhy+nOdBhNRL/lKSvlhZLCCAfY
f1eJrB0rAzQpCqw8Wuz2JzWsxBiTt+6Ucuzv4EkFVrt7Xnj00feghTKJkVDqa+fL
B9hTiiYh8sLGJkYHsZLDZIzAdOW8jmun1I+XFsjdl7ucLRYz6U8NL9jc6oIGK00=
=KJmM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2019-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to reset the NIC after setting the bits to enable power
gating and that cannot be done too late in the flow otherwise it
cleans other registers and things that were already configured,
causing initialization to fail.
In order to fix this, move the function to the common code in trans.c
so it can be called directly from there at an earlier point, just
after the reset we already do during initialization.
Fixes: 9a47cb9883 ("iwlwifi: pcie: add workaround for power gating in integrated 22000")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205719
Cc: stable@ver.kernel.org # 5.4+
Reported-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 968dcfb490.
Both that commit and commit 809805a820
attempted to fix the same bug (dead assignments to the local variable
cfg), but they did so in incompatible ways. When they were both merged,
independently of each other, the combination actually caused the bug to
reappear, leading to a firmware crash on boot for some cards.
https://bugzilla.kernel.org/show_bug.cgi?id=205719
Signed-off-by: Anders Kaseorg <andersk@mit.edu>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") has applied batched GRO_NORMAL packets processing
to all napi_gro_receive() users, including mac80211-based drivers.
However, this change has led to a regression in iwlwifi driver [1][2] as
it is required for NAPI users to call napi_complete_done() or
napi_complete() and the end of every polling iteration, whilst iwlwifi
doesn't use NAPI scheduling at all and just calls napi_gro_flush().
In that particular case, packets which have not been already flushed
from napi->rx_list stall in it until at least next Rx cycle.
Fix this by adding a manual flushing of the list to iwlwifi driver right
before napi_gro_flush() call to mimic napi_complete() logics.
I prefer to open-code gro_normal_list() rather than exporting it for 2
reasons:
* to prevent from using it and napi_gro_flush() in any new drivers,
as it is the *really* bad way to use NAPI that should be avoided;
* to keep gro_normal_list() static and don't lose any CC optimizations.
I also don't add the "Fixes:" tag as the mentioned commit was only a
trigger that only exposed an improper usage of NAPI in this particular
driver.
[1] https://lore.kernel.org/netdev/PSXP216MB04388962C411CD0B17A86F47804A0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
[2] https://bugzilla.kernel.org/show_bug.cgi?id=205647
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Tested-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Reviewed-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We trace the whole TFD with all TBs when in iwlwifi_dev_tx,
but sometimes we add TBs to it later and then we don't have
any of this data. Trace the I/O virtual address (IOVA) (it
can be the physical address, or as returned by the IOMMU)
here to aid debugging the DMA flows.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is a little less efficient now as it's known to be a
multiqueue device in this function, but a future patch will
have to use a variable here anyway, so use rxq->queue_size
now instead to make it clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These aren't used outside the rx.c file, so make them static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the implementation of SKBs with fraglist was sent upstream, a
merge-damage occurred and half the patch was not applied.
This causes problems in high-throughput situations with AX200 devices,
including low throughput and FW crashes.
Introduce the part that was missing from the original patch.
Fixes: 0044f1716c ("iwlwifi: pcie: support transmitting SKBs with fraglist")
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[ This patch was created by me, but the original author of this code
is Johannes, so his s-o-b is here and he's marked as the author of
the patch. ]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable bufsz is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is called within tx-gen2.c only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
From gen2 PN is totally offloaded to hardware (also the space for the
IV isn't part of the skb). As you can see in mvm/mac80211.c:3545, the
MAC for cipher types CCMP/GCMP doesn't set
IEEE80211_KEY_FLAG_PUT_IV_SPACE for gen2 NICs.
This causes all the AMSDU data to be corrupted with cipher enabled.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new debug TLVs API preprocessing.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow collecting monitor data in ini debug mode.
Implement both SMEM and DRAM monitor regions dumping.
For DRAM monitor, support DBGC1, DBGC2 and DBGC3 and support several
DRAM fragments per DBGC.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Legacy DRAM monitor does not support multi buffers.
Remove this infra.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When converting the wrong qu configurations in an earlier commit, I
accidentally swapped 0x2720 and 0x30DC. Instead of converting 0x2720,
I converted 0x30DC. Undo 0x30DC and convert 0x2720.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a workaround that forces power gating to be enabled on integrated
22000 devices. This improves power saving in certain situations.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A bunch of the entries for qnj were wrong. The 9460 device doesn't
exist, so update them to 9461 and 9462. There are still a bunch of
other occurrences of 9460, but that will be fixed separately.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some entries for PCI ID 0x2720 were using iwl9260_2ac_cfg, but the
correct is to use iwl9260_2ac_cfg_soc. Fix that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two patches were sent out of order: one removed some conditions from
an if and the other moved the code elsewhere. When sending the patch
that moved the code, an older version of the original code was moved,
causing the "make QnJ exclusive" code to be essentially undone.
Fix that by removing the inclusive conditions from the check again.
Fixes: 809805a820 ("iwlwifi: pcie: move some cfg mangling from trans_pcie_alloc to probe")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There were a bunch of devices with qu and jf that were loading the
configuration with pu and jf, which is wrong. Fix them all
accordingly. Additionally, remove 0x1010 and 0x1210 subsytem IDs from
the list, since they are obviously wrong, and 0x0044 and 0x0244, which
were duplicate.
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_pcie_ctxt_info_gen3_init there are cases that the allocated dma
memory is leaked in case of error.
DMA memories prph_scratch, prph_info, and ctxt_info_gen3 are allocated
and initialized to be later assigned to trans_pcie. But in any error case
before such assignment the allocated memories should be released.
First of such error cases happens when iwl_pcie_init_fw_sec fails.
Current implementation correctly releases prph_scratch. But in two
sunsequent error cases where dma_alloc_coherent may fail, such
releases are missing.
This commit adds release for prph_scratch when allocation for
prph_info fails, and adds releases for prph_scratch and prph_info when
allocation for ctxt_info_gen3 fails.
Fixes: 2ee8240262 ("iwlwifi: pcie: support context information for 22560 devices")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't handle failures in the rb_allocator workqueue allocation
correctly. To fix that, move the code earlier so the cleanup is
easier and we don't have to undo all the interrupt allocations in
this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We got a crash in iwl_trans_pcie_get_cmdlen(), while the TFD was
being accessed to sum up the lengths.
We want to access the TFD here, which is the information for the
hardware. We always only allocate 32 buffers for the cmd queue,
but on newer hardware (using TFH) we can also allocate only a
shorter hardware array, also only 32 TFDs. Prior to the TFH, we
had to allocate a bigger TFD array but would make those point to
a smaller set of buffers.
Additionally, now max_tfd_queue_size is up to 65536, so we can
access *way* out of bounds of a really only 32-entry array, so
it crashes.
Fix this by making the TFD index depend on which hardware we are
using right now.
While changing the calculation, also fix it to not use void ptr
arithmetic, but cast to u8 * before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new device generation has a slightly different suspend resume flow
Currently, the way the driver instruct the device to move to D3 is by
sending D3_CONFIG_CMD.
Instead of using the host command the indication is by writing to the
doorbell interrupt.
The FW will respond with interrupt to indicate transition completion.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of accessing the iwl_config_trans_params from the cfg that is
stored in the trans struct, pass this structure directly to functions
that need it during trans_alloc. This will be useful to isolate the
elements needed during allocation and pass them separately before the
actual cfg struct is known.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the cfg to iwl_trans already during allocation, set
it only later when we have had the time to decide which cfg to use.
This is part of the effort to be able to decide the cfg based on HW
revision and RF ID after iwl_trans_alloc() has been called.
For now, since we still have a bunch of code checking the HW revision
and the RF ID, we set iwl_trans->cfg early, even before we decided the
real cfg to use. We only use the trans configuration at this point,
so this is fine for now. In the future, the trans configuration will
be completely independent from the rest of the config structure, so
we'll be able to avoid this.
Additionally, we can't access the PRPH registers in iwl_trans_alloc()
anymore, so move the HW REV C-step check for family 8000 code later to
the probe function as well. This step is probably not necessary, but
if that's the case it should be removed separately later on.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There were a couple of special handling to find the correct cfg inside
iwl_trans_pcie_alloc(). Move them to iwl_pci_probe() so they're
together with the rest of the decisions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of using iwl_trans->cfg in iwl_trans_pcie_alloc(), use the
local argument that we received. This will allow us to not to set the
cfg during iwl_trans_alloc() so it can be decided later.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align wrt log prints to the driver coding style
Remove the ext field from the log and print it at the beginning of the
apply point.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
use iwl_trans_dbg_ini_valid function instead of a boolean value check if
dbg_ini mode is on. It is needed for a future patch.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
dma_alloc_coherent is not just the page allocator. The only valid
arguments to pass are either GFP_ATOMIC or GFP_ATOMIC with possible
modifiers of __GFP_NORETRY or __GFP_NOWARN.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This means:
1) stop calling pm_runtime_resume when starting the hardware
2) removing the unneeded low_power parameter to start / stop hw / fw
transport ops
3) squashing transport functions that are now the same
_iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the now unneeded functions that called those from the
transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is always set to IWL_PLAT_PM_MODE_DISABLED
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During D3 state, FW may send packets.
As a result, "write" queue pointer will be incremented by FW.
Upon resume from D3, driver should adjust its shadows of "write" and "read"
pointers to the value reported by FW.
1. Keep TID used during wowlan configuration.
2. Upon resume, set driver's "write" and "read" queue pointers
to the value reported by FW.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This flag should never be set unless integration work with the
platform is done. We don't support any platforms officially and don't
plan to do so in the near future, so we can remove this option
entirely in order to avoid having it enabled by mistake.
This has been marked with "depends on EXPERT", so there shouldn't be
many systems running with it set. And, if there are systems, they
should not be using this flag.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were erroneously assigning the new configuration to a local
variable cfg, but that was not being assigned to anything, so the
change was getting lost. Assign directly to iwl_trans->cfg instead.
Fixes: 5a8c31aa63 ("iwlwifi: pcie: fix recognition of QuZ devices")
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to use a different firmware for C0 versions of killer Qu NICs.
Add structures for them and handle them in the if block that detects
C0 revisions.
Additionally, instead of having an inclusive check for QnJ devices,
make the selection exclusive, so that switching to QnJ is the
exception, not the default. This prevents us from having to add all
the non-QnJ cards to an exclusion list. To do so, only go into the
QnJ block if the device has an RF ID type HR and HW revision QnJ.
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the HW revision of Qu devices we found is QuZ, then we need to
switch the configuration accordingly in order to use the correct FW.
Add a block of ifs in order do that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have a too generic condition that switches from Qu configurations
to QnJ configurations. We need to exclude some configurations so that
they are not erroneously switched. Add the ax201 configuration to the
list of exclusions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Starting from 22560, the byte count is expected to be in
bytes and we have now 14 bits. Ajust the code to this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to remember how to unmap a memory (as single or
as page), we maintain a bit per Transmit Buffer (TBs) in
the meta data (structure iwl_cmd_meta).
We maintain a bitmap: 1 bit per TB.
If the TB is set, we will free the memory as a page.
This bitmap was never cleared. Fix this.
Cc: stable@vger.kernel.org
Fixes: 3cd1980b0c ("iwlwifi: pcie: introduce new tfd and tb formats")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a few PCI ID'S for 9000 series.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for C-step devices. Currently we don't have a nice way of
matching the step and choosing the proper configuration, so we need to
switch the config structs one by one.
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add two new PCI ID's for 9000 and 20000 series
Cc: stable@vger.kernel.org
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes the register status can include interrupts that
were masked. We can, for example, get the RF-Kill bit set
in the interrupt status register although this interrupt
was masked. Then if we get the ALIVE interrupt (for example)
that was not masked, we need to *not* service the RF-Kill
interrupt.
Fix this in the MSI-X interrupt handler.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newest devices have a new firmware load mechanism. This
mechanism is called the context info. It means that the
driver doesn't need to load the sections of the firmware.
The driver rather prepares a place in DRAM, with pointers
to the relevant sections of the firmware, and the firmware
loads itself.
At the end of the process, the firmware sends the ALIVE
interrupt. This is different from the previous scheme in
which the driver expected the FH_TX interrupt after each
section being transferred over the DMA.
In order to support this new flow, we enabled all the
interrupts. This broke the assumption that we have in the
code that the RF-Kill interrupt can't interrupt the firmware
load flow.
Change the context info flow to enable only the ALIVE
interrupt, and re-enable all the other interrupts only
after the firmware is alive. Then, we won't see the RF-Kill
interrupt until then. Getting the RF-Kill interrupt while
loading the firmware made us kill the firmware while it is
loading and we ended up dumping garbage instead of the firmware
state.
Re-enable the ALIVE | RX interrupts from the ISR when we
get the ALIVE interrupt to be able to get the RX interrupt
that comes immediately afterwards for the ALIVE
notification. This is needed for non MSI-X only.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We added code to restock the buffer upon ALIVE interrupt
when MSI-X is disabled. This was added as part of the context
info code. This code was added only if the ISR debug level
is set which is very unlikely to be related.
Move this code to run even when the ISR debug level is not
set.
Note that gen2 devices work with MSI-X in most cases so that
this path is seldom used.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 0xF6 command used to start and stop the recording from 22560 devices
was removed. This is causing an assert when the driver tries to alter
the recording state.
Remove the use of the command.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unite iwl_trans debug related fields under iwl_trans_debug struct to
increase readability and keep iwl_trans clean.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several flows where the driver checks if it runs in ini mode.
Some of these flows are no longer used in ini mode or there is another
condition that check the ini mode in the same flow. Either way, those
conditions are redundant. Remove the redundant conditions.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we dump only the first 64 bytes of the PCI config space,
which leaves out some important things, such as the base address
registers.
Increase it to 352 for the PCI device and to 524 for the rootport to
make sure we include everything we need.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Improve the robustness of the dump collection flow in case of an early
error:
1. in iwl_trans_pcie_sync_nmi, disable and enable interrupts only if
they were already enabled
2. attempt to initiate dump collection in iwl_fw_dbg_error_collect only
if the device is enabled
3. check Tx command queue was already allocated before trying to collect it
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 22000 series FW that was meant to be used with hr is
also the FW that is used for hr1 and has a different RF ID.
Add support to load the hr FW when hr1 RF ID is detected.
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
change the fw of 0x02F0 platform from qu to quz
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add few PCI ID'S for 22000 and chainge few cards structs names
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add few PCI ID'S for 22000 and fix the wrong name for one
of the structs
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Read fseq info from FW registers and print it upon fw assert.
The print is needed since the fseq version coming from the TLV might
not be the actual version that is used.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver attempts to clear persistence bit on any device familiy even
though only 9000 and 22000 families require it. Clear the bit only on
the relevant device families.
Each HW has different address to the write protection register. Use the
right register for each HW
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 8954e1eb22 ("iwlwifi: trans: Clear persistence bit when starting the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we have a single image (same firmware image for INIT and
OPERATIONAL), we couldn't load the driver and register to the
stack if we had hardware RF-Kill asserted.
Fix this. This required a few changes:
1) Run the firmware as part of the INIT phase even if its
ucode_type is not IWL_UCODE_INIT.
2) Send the commands that are sent to the unified image in
INIT flow even in RF-Kill.
3) Don't ask the transport to stop the hardware upon RF-Kill
interrupt if the RF-Kill is asserted.
4) Allow the RF-Kill interrupt to take us out of L1A so that
the RF-Kill interrupt will be received by the host (to
enable the radio).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJczDAZAAoJEG4XJFUm622blLgH/jdBKEq9i1m5dtLi48u4sgPV
NsnPhR5XQjpbYpmvgPslKLxWzZq6A0P+lo9QqTXkP/QRyJLu7RnoY1c2wVsQbWaK
VTXc0cROzWt0ihAt8Mc/rEsZpISVnQ9mJbTd/kSJM9WlDeIg0jcJvnEAdQiEmM5t
2t+zZ5CupUXYbGE3zWHL1GSjBD9f0v7zyrNxYNGfvqhDEXhTFWAmVuRtfoAVlRU+
dt1HMv+qdxgoF6Uvaw/kgY09mDvdrfy2EVL0q7S3TKceute60SWf7de2sToI/rMQ
snUnVqTIIUnWPl6g+C3Bp2TbdZhy6XCSRsMFOVa2i1Lt+z1qe3dTr3hjxTQWRhE=
=uLaP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a solitary and inconspicous ` in the middle of a comment in
this function, which should not be there. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If for some reason the device gives us an RX interrupt before we're
ready for it, perhaps during device power-on with misconfigured IRQ
causes mapping or so, we can crash trying to access the queues.
Prevent that by checking that we actually have RXQs and that they
were properly allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will let us introduce a mechanism to start with rfkill
faked, and put 0 here to override it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debug prints to the ini flow and rewrite existing prints to provide
more information
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TFD_*_SLOTS and IWL_*_QUEUE_SIZE both define the TX queue
size (number of TFDs).
Get rid of TFD_*_SLOTS and use only IWL_*_QUEUE_SIZE.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcuHgsAAoJEG4XJFUm622bfo8H/3uRRxsQBHGg6e3NpELaxpNV
IfrPDtvxyfILzIepBBhnZYUY0OrlTHKfMmzFBD9FFMojsxBYddnLZ/0iKUNKfwLm
KzToW/64YJ784dc+tw85gjh8I3MB+RRoD0l01M1HuOkzQ4hDNEGK3IsMHsBs/oTZ
huiqTYsTxStOj53vOpQiBFZ1pYBtvGLMxBdSepDcR27bgT1gwriynCSkSNglDH8z
/t3m6hDGtZa6uVkoIVH+BAMu6+vt+vIkU/TOdmiW/zqBL2JYq6cDE0uIb3bLAzN6
uvS1Rj42P3OwHUwFavlUBdr5Rdcj6P24S5ZhtVaGGWCBjMZI5/nO7IjzwyQnQuQ=
=/6q9
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses msix causes-register to handle both msix and non msix
interrupts when performing sync nmi. On devices that do not support
msix this register is unmapped and accessing it causes a kernel panic.
Solve this by differentiating the two cases and accessing the proper
causes-register in each case.
Reported-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Two of the PCI ID entries for the 22260 series were incorrectly using
the subsystem vendor ID (which we ignore) as the PCI device ID. This is
obviously wrong and can be simply removed since we already have the
correct entries in the list.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AX210 devices support 256 BA (256 MPDUs in an AMPDU).
The firmware requires that the number of TFDs will be
minimum twice as big as the BA size (2 * 256 = 512).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Differentiate between SW and HW error interrupts and support ini HW
error trigger.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new configuration with a new firmware name for quz devices.
And, since these devices have the same PCI device and subsystem IDs,
we need to add some code to switch from a normal qu firmware to the
quz firmware.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to perform monitor dumping on AX210 device family
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The layout of the RBD (receive buffer descriptor) isn't quite right,
the hardware ended up being implemented differently. Switch to the
correct RBD layout. While at it, remove the now useless extra defines.
Also, switch the CD (completion descriptor) to the right format, which
is basically just a code cleanup because the only field we really used
(rbid) is still in the same place. We may need fragmentation later if
we ever want to use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Only add the size of the tx command to the dump file size if it is set
in the dump_mask.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
rename few structs to fit the new marketing names
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow modules from outside pcie to call sync_nmi.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a few PCI ID'S for 22000 and killer series in addition to
chainging the marketing name.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AX210 devices assume that the (DRAM) addresses of the rb_stts's for
the different queues are continuous.
So allocate the rb_stts's for all the Rx queues in one place.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't support A-step for some device combinations anymore. So
change them to use B-step, renaming and reorganizing the config
structures. Additionally, fix one device that was using the wrong
configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AX210 family, UMAC periphery address space moved from
0xA00000 to 0xD00000.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When flushing TX queues no new TX should go into the system.
However, in the following scenario we get TX:
1. Queues are stopped and there are packets in overflow queue
2. Station is removed and flush begins
3. Flush empties space, and reclaim path TXes SKB from overflow
queue.
Note that the fact the queues are stopped during the process
doesn't matter - the packet will be TXed since the TX path
doesn't care if TX queues are stopped or not, just if there is
space in the queue, which there is, since we just freed a
packet.
A fix here is rather complicated, since the flow is very racy.
Change code not to warn if we are TXing from overflow TX.
In case there is TX from both overflow TX and TX path we will
miss a warning we optimally had, but we can live with that.
Make sure we don't return before overflow queue is empty, otherwise
we will think queues are empty, but they will be refilled, resulting
with assert.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 3955525d5d ("iwlwifi: pcie: buffer packets to avoid overflowing Tx queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new device family AX210.
Make the needed changes for this family.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently there is no way to debug RX/TX paths using prints
without harming tpt. Add prints to debug RX allocation path.
We can still get 1.9 gbps with those on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allocator swaps the pending requests with 0 when it starts
working. This means that relying on it n RX path to decide if
to move to emergency is not always a good idea, since it may
be zero, but there are still a lot of unallocated RBs in the
system. Change allocator to decrement the pending requests on
real time. It is more expensive since it accesses the atomic
variable more times, but it gives the RX path a better idea
of the system's status.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 868a1e863f ("iwlwifi: pcie: avoid empty free RB queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Work on the new debugging infrastructure continues;
* HE radiotap;
* Support for new FW version 44;
* A couple of new FW API changes;
* A bunch of fixes for static analyzer reported issues;
* General bugfixes;
* Other cleanups and small fixes;
-----BEGIN PGP SIGNATURE-----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=ckmd
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2019-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Third batch of iwlwifi patches intended for v5.1
* Work on the new debugging infrastructure continues;
* HE radiotap;
* Support for new FW version 44;
* A couple of new FW API changes;
* A bunch of fixes for static analyzer reported issues;
* General bugfixes;
* Other cleanups and small fixes;
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWoRZAAoJEG4XJFUm622bOm4H/j2Tt6qS5yz3ioH2I7R+f7e/
8C2JJia+uQs8iChdyCjCFcDymmjB2l5u72JvupwCdERzp3okv/xmJiLW5wFW2z4x
B3Nrd4FV2EMIdsRXg1RWbwZHC4wIY6lFhL1OcUcuNwpb5ab1ppvQFHmH5logd7DC
euFSe02g8xmXdUMciRDKGUdiSiDIApmx9dUfguaqYtepqeW3hmDEEkeDicaf2fjq
cM5qAvssIAgUTqwIImEQQEU7j7A2TgMYkRBNzwv2QG47jy6OlgXkZVByvtq59irg
v4BFNtG6uRWTugxQ/FwYWeqsrnjegFNKm5MFbS6BDxbe05M7QzeK8zm55fE9ZGk=
=cHbd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The typical sequence of setting INIT_DONE and then waiting
for clock stabilisation is going to need a new workarounds,
so first of all refactor it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Both iwl_trans_fw_error and iwl_force_nmi initiate async recovery flow.
Calling them both is redundant and causing a race.
Solve this by removing the call to iwl_trans_fw_error.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: cfadc3ffcc ("iwlwifi: pcie: stop the firmware when we restart it")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement paging memory dump in the new dump mechanism.
To support this change, moved iwl_self_init_dram strcut from trans_pcie
to trans so that it will accessible via fw_runtime.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Prior to gen2 we allocate the paging memory via alloc_pages
which requires passing ownership on the memory between the
cpu and the device using dma_sync_single_for_cpu and
dma_sync_single_for_device.
Add missing dma_sync_single_for_device in iwl_dump_paging
after copying the memory.
since gen2, we allocate the paging memory using dma_alloc_coherent
which does not need passing ownership between the cpu and device.
Remove unneeded call to dma_sync_single_for_cpu in
iwl_trans_pcie_dump_data prior to copying the memory.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 5538409ba3 ("iwlwifi: pcie: support page dumping in wrt in gen2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
update the product name for the some of the cards from
the series of 9260 and 9560
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
That's what we pass, and we don't want/need any negative values.
Found by sparse/smatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we use a dumping mask, checking if only monitor was requested
is redundant. Remove the unneeded code.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The out_cmd structure starts with a header, so there's no need to use
&out_cmd->hdr, out_cmd alone is enough. We use this when calculating
other addresses and klocwork gets confused with that because it thinks
we are trying to access hdr (as an array) beyond its size.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These files have a long history of code changes, but analysing
the remaining code leads to having only a few changes that are
not already owned by Intel, notably from
- Andy Lutomirski <luto@amacapital.net>
- Joonwoo Park <joonwpark81@gmail.com>
- Kirtika Ruchandani <kirtika@chromium.org>
- Rajat Jain <rajatja@google.com>
- Stanislaw Gruszka <sgruszka@redhat.com>
remaining in the code today.
Note that
- I myself was working for Intel and for any possibly code
that might be before my employment there give permission
- Wizery employees were working for Intel
More specifically, we identified the following commits that
(partially may) remain today:
25c03d8e8c Joonwoo Park <joonwpark81@gmail.com> ("iwlwifi: do not schedule tasklet when rcv unused irq")
f36d04abe6 Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: use dma_alloc_coherent")
387f3381f7 Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: fix dma mappings and skbs leak")
2624e96ce1 Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: fix possible data overwrite in hcmd callback")
bfe4b80e9f Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: always check if got h/w access before write")
d536c32b45 Andy Lutomirski <luto@amacapital.net> ("iwlwifi: pcie: log when waking the NIC for hcmd submission fails")
a6d24fad00 Rajat Jain <rajatja@google.com> ("iwlwifi: pcie: dump registers when HW becomes inaccessible")
fb12777ab5 Kirtika Ruchandani <kirtika@chromium.org> ("iwlwifi: Add more call-sites for pcie reg dumper")
3a73a30049 Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: cleanup/fix memory barriers")
aa5affbacb Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: dump stack when fail to gain access to the device")
Align the licenses with their permission to clean up and to
make it all identical.
CC: Joonwoo Park <joonwpark81@gmail.com>
CC: Stanislaw Gruszka <sgruszka@redhat.com>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Rajat Jain <rajatja@google.com>
CC: Kirtika Ruchandani <kirtika@chromium.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kirtika Ruchandani <kirtika@chromium.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Joonwoo Park <joonwpark81@gmail.com>
Acked-by: Rajat Jain <rajatja@google.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case there are bugs in this area, this data can
help with debugging.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code checks that we haven't exceeded the maximum number of
TBs by comparing to a define of gen1 instead of gen2, fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Klocwork complains about copying from dev_cmd->hdr if
copying more than 4 bytes since it means part of the
copy is from the next field. This isn't a real bug,
but for not failing Klocwork next time - fix this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver assumes certain sizes and lengths aren't crossed in some
places. Make sure this indeed happens.
Found by Klocwork.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function was only used by 9000 A-step devices, which we don't
support anymore, so it can be removed.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the cfg struct names is mistakenly "iwl22000", when it should
be "iwl22560".
Chage-Id: If9fbfa4bceef81d028c90c98d47115fbe39da547
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Fixes: 2f7a386319 ("iwlwifi: rename the temporary name of A000 to the official 22000")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some devices with PCI ID 0x2723, which is supposed to be 22260, are
actually not. So we need to differentiate them by checking the hw_rev
and change the cfg accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Don't populate the array prop on the stack but instead make it static.
Makes the object code smaller by 30 bytes:
Before:
text data bss dec hex filename
80138 15382 576 96096 17760 drivers/net/wireless/intel/iwlwifi/pcie/trans.o
After:
text data bss dec hex filename
79948 15542 576 96066 17742 drivers/net/wireless/intel/iwlwifi/pcie/trans.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
In reclaim code, we don't need to take the queue lock for
waking the queue. The code section is executed only when
the tx path is stopped, and since the reclaim path is not
executed in parallel to itself, no one can update the queue
pointers, and accessing them is safe without a lock.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When building AMSDU for gen2, code uses iwl_tx_cmd. The only
updated field is len, which is in the same location, so it
is not a bug. However, it is a bit confusing and error prone,
so change it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
command len is set too early in the code, since when building
AMSDU, the size changes. This causes the byte count table to
have the wrong size.
Fixes: a0ec0169b7 ("iwlwifi: support new tx api")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When removing the driver, the following flow can happen:
1. host command is in progress, for example at index 68.
2. RX interrupt is received with the response.
3. Before it is processed, the remove flow kicks in, and
calls iwl_pcie_txq_unmap. The function cleans all DMA,
and promotes the read pointer to 69.
4. RX thread proceeds with the processing, and is calling
iwl_pcie_cmdq_reclaim, which will print this error:
iwl_pcie_cmdq_reclaim: Read index for DMA queue txq id (0),
index 4 is out of range [0-256] 69 69.
Detect this situation, and avoid the print. Change it to
warning while at it, to make such issues more noticeable
in the future.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When ini TLVs are loaded, dump data according to the
stored configuration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW debug data will oneshot read all data available in DRAM
and fill the supplied user buffer. In case the read request
is greater than the new data in DRAM, the driver will write
all data it has and return the buffer immediately.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have to choose different configuration and different firmwares
depending on the external RF module that is installed. Since the
external module is not represented in the PCI IDs, we need to change
the configuration at runtime, after checking the RF ID of the module
installed. We have a bit of a mess in the code that does this,
because it applies cfg's according to the RF ID only, ignoring the
integrated module that is in use.
Fix that for some devices by adding correct configurations for them
and not ignoring the integrated module's type when making the
decision.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently opmode is limited to asking transport to either
dump all the dumps configured at startup, or monitor only.
Instead, pass to transport a bitmask, to allow flexibility.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The trigger structure is being passed around, when
all we care about is whether to dump only monitor
or not. Pass a bool instead.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently code sets the write pointer when getting the TX queue
allocate response. This causes a redundant interrupt with any actual
change in the pointer. Remove this write altogether.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In D3 suspend flow in 9260 gen2 HW, the NIC receives two PERST signals.
The first PERST is expected and indicates the device on coming resume flow.
The second PERST causes FW restart FW restart.
In order to avoid this issue, the FW set the persistence bit on.
Once this bit is set, the FW ignores reset attempts.
The problem is when the FW gets assert during D3 and then the persistence
bit is set and causes the FW to ignore reset.
To handle this issue, the FW opens the preg bit which allows access
to the persistence bit, so that the driver clear the persistence bit
and reset the NIC.
The flow is as follows:
the driver checks if the persistence bit is set.
If the bit is set, the driver checks if he can clear the bit.
If the driver can not clear the bit then there is no point to continue
configuring the NIC since it will fail.
The fix was added is in start HW flow instead of the resume flow since in
general, if the persistence bit is set, the driver can not start the FW.
So it is good to check it when we start configuring the NIC.
The driver does not need to close the preg bit since the FW close it
during the start flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split TX tracing to be per TB. This is needed now that
AMSDUs can be sent and skb can be larger than trace
limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we TX AMSDU, we shouldn't pad the packet. In the past,
we were building AMSDU only in transport layer, and gen2
functions are built based on this. However, now that op mode
may build AMSDUs, we need to take care of padding also in
gen2 "non-pcie-amsdu" path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we use the iwl_pcie_txq_build_tfd() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we use the iwl_pcie_gen2_set_tb() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Fixes: ab6c644539 ("iwlwifi: pcie: copy TX functions to new transport")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If all free RB queues are empty, the driver will never restock the
free RB queue. That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.
Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).
There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.
But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).
To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The debug variables are bloating the iwl_fw struct. And the fields
are out of order, missing docs and some are redundant.
Clean this up. This serves as preparation for unionizing it for the
new ini infra.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In future devices we will have more than one debug buffer.
Prepare the infrastructure for allocation and release of
multiple debug buffers by grouping the variables in an array
of structures and moving it to trans section, where they will
be visible to opmode and FW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to be able to build A-MSDUs in higher layers, e.g. by
xmit_more, so support transmitting SKBs with fraglist to use
it for such.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
RB size can be configured by user to be greater than 4K.
That's needed for monitor to capture big AMSDUs.
The firmware now enables different RB sizes configuration
via context info.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Today, the length of a debug message in iwl_trans_pcie_reclaim
may pass the MAX_MSG_LEN, which is 110.
An example for this kind of message is:
'iwl_trans_pcie_reclaim: Read index for DMA queue txq id (2),
last_to_free 65535 is out of range [0-65536] 2 2.'
Cut the message a bit so it will fit the allowed MAX_MSG_LEN.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the HW is not responding at probe time, fail immediately complaining
about it. Without this, we see that the kernel spends > 100ms trying to
load firmware (even gives an incorrect impression that it actually
loaded a firmware) and do unnecesary processing before concluding that
the device is not accessible:
INFO kernel: [ 34.092678] iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
WARNING kernel: [ 34.093560] iwlwifi 0000:01:00.0: Direct firmware load for iwl-dbg-cfg.ini failed with error -2
INFO kernel: [ 34.111523] iwlwifi 0000:01:00.0: loaded firmware version 17.318154.0 op_mode iwlmvm
INFO kernel: [ 34.173250] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0xFFFFFFFF
ERR kernel: [ 34.198023] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
ERR kernel: [ 34.198044] iwlwifi 0000:01:00.0: iwlwifi device config registers:
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will allow us to reuse the function later for adding fraglist
SKBs to the TFD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When anything fails, we unmap the whole TFD in three different
places scattered throughout the code. Unify this to a single
place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the incoming frame should be an A-MSDU, it may already be one,
for example in the case of NAN multicast being encapsulated in an
A-MSDU. Thus, use the GSO algorithm to build A-MSDU only if the
skb actually contains GSO data.
Fixes: 6ffe5de35b ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the skb fragment loop into a helper routine to be able
to reuse it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For newer devices we have higher range of periphery
addresses. Currently it is masked out, so we end up
reading another address.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cleanup of the debug flow by moving several flows to separate
functions to increase readability. Three functions were created:
1. iwl_fw_get_prph_len - returns the size needed for periphery dump.
2. iwl_fw_dump_mem for - executes the memory dumping flow.
3. iwl_trans_get_fw_monitor_len - returns the size needed for monitor dump.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The devices with PCI device ID 0x34F0 are part of the SoC and can be
combined with some different external RF modules. The configuration
for these devices should reflect that, but are currently mixed up. To
avoid confusion with discrete devices, add part of the firmware to be
used and the official name of the device to the cfg structs.
This is least reorganization possible (without messing things even
more) that could be done as a bugfix for this SoC. Further
reorganization of this code will be done separately.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support more txq_alloc command types by moving the command declaration
to the gen specific area. While at it, move some of the code segments
to a common place for re-use.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make all FW debug data stop recording flows to use
iwl_fw_dbg_stop_recording function instead of writing to FW
registers directly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow access to the memory by the host and the device simultaneously.
This will be needed in some future patches.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We offloaded all the RX configuration of init to firmware. However,
the configuration of interrupt coalescing was left hanging - it wasn't
offloaded nor was it written by host.
This write to the CSR is allowed in gen2, so the host can do it.
Without it we have various issues with RX fullness.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the NIC is disconnected, we just can't do anything
besides seeking for help from the bus driver. Dumping the
device's memory is not necessary and just bloats the logs
with unusable data. Moreover, asking mac80211 to restart
the hardware is also useless. Bypass all this.
Also, use the STATUS_TRANS_DEAD status bit instead of a
bool inside the transport layer. The advantage of this is
that now, the transport and the op_mode can know what is the
situation and bypass the useless recovery steps mentioned
above.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the NIC is disconnected from PCI bus, we are not
able to access it anymore. Check the status to avoid
some unnecessary work so can improve the performance.
It will help to make PCI bus rescan to bring back the
device much faster.
The real test is able to improve 7 seconds.
[w/o patch] It takes around 9 seconds
..
2018-04-20T01:22:39.691929-07:00 WARNING kernel:
[ 66.335881] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
..
2018-04-20T01:22:48.101094-07:00 INFO kernel:
[ 74.747364] iwlwifi 0000:01:00.0: loaded firmware version 29.610311.0 op_mode iwlmvm
[w/a patch] It takes about 2 seconds.
..
2018-04-20T01:18:16.454087-07:00 WARNING kernel:
[ 75.966860] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
..
2018-04-20T01:18:18.602717-07:00 INFO kernel:
[ 78.116132] iwlwifi 0000:01:00.0: loaded firmware version 29.610311.0 op_mode iwlmvm
..
Fixes: 49564a806f ("iwlwifi: pcie: remove non-responsive device")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will allow using the same init in future generations.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Store the default rxq number in a variable, so we won't need
to use the actual number in the code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is used only within PCIe, and there's no reason to go through
the transport methods for a function call within PCIe itself.
Remove the dump_regs() method and call the function directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow other device generations to use the utilities that
are used to send and reclaim host commands and to allocate
rx, by making it non-static.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We would like to allow using tx init code for other queues but
the command queue - for newer devices.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to drop packets with errors (such as replay,
MIC, ICV, conversion, duplicate and so on).
Drop invalid packets, put the status bits in the metadata and
move the enum definition to the correct place (FW API header).
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
-----BEGIN PGP SIGNATURE-----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=2Dmn
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a
device below it (Myron Stowe)
- Simplify SHPC existence/permission checks (Bjorn Helgaas)
- Remove hotplug sample skeleton driver (Lukas Wunner)
- Convert pciehp to threaded IRQ handling (Lukas Wunner)
- Improve pciehp tolerance of missed events and initially unstable
links (Lukas Wunner)
- Clear spurious pciehp events on resume (Lukas Wunner)
- Add pciehp runtime PM support, including for Thunderbolt controllers
(Lukas Wunner)
- Support interrupts from pciehp bridges in D3hot (Lukas Wunner)
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph
Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is
supplied (Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum
(Jakub Kicinski)
- Set IRQCHIP_ONESHOT_SAFE for PCI MSI irqchips (Heiner Kallweit)
- Document ACPI description of PCI host bridges (Bjorn Helgaas)
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
- To avoid bus errors, enable PASID only if entire path supports
End-End TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD
Controller (Bjorn Helgaas)
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
- Remove Aardvark outbound window configuration (Evan Wang)
- Fix Aardvark bridge window sizing issue (Zachary Zhang)
- Convert Aardvark to use pci_host_probe() to reduce code duplication
(Thomas Petazzoni)
- Correct the Cadence cdns_pcie_writel() signature (Alan Douglas)
- Add Cadence support for optional generic PHYs (Alan Douglas)
- Add Cadence power management ops (Alan Douglas)
- Remove redundant variable from Cadence driver (Colin Ian King)
- Add Kirin MSI support (Xiaowei Song)
- Drop unnecessary root_bus_nr setting from exynos, imx6, keystone,
armada8k, artpec6, designware-plat, histb, qcom, spear13xx (Shawn
Guo)
- Move link notification settings from DesignWare core to individual
drivers (Gustavo Pimentel)
- Add endpoint library MSI-X interfaces (Gustavo Pimentel)
- Correct signature of endpoint library IRQ interfaces (Gustavo
Pimentel)
- Add DesignWare endpoint library MSI-X callbacks (Gustavo Pimentel)
- Add endpoint library MSI-X test support (Gustavo Pimentel)
- Remove unnecessary GFP_ATOMIC from Hyper-V "new child" allocation
(Jia-Ju Bai)
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect
(Ray Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
- Fix mobiveil iomem/phys_addr_t type usage (Lorenzo Pieralisi)
- Fix mobiveil missing include file (Lorenzo Pieralisi)
- Add mobiveil Kconfig/Makefile support (Lorenzo Pieralisi)
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (153 commits)
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI: Limit config space size for Netronome NFP5000
PCI/MSI: Set IRQCHIP_ONESHOT_SAFE for PCI-MSI irqchips
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Check for PCIe Link downtraining
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
...
This part of the iwlwifi driver doesn't need anything provided by
pci-aspm.h, so remove the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbZyxDAAoJEG4XJFUm622bq2AH/2yJAeOKb7Z25ezsvldaEDd3
cYS4TjLevXacDU5NdINtm1IRMct1ZldwUjrjgR2I/eLaSHhxyIdV4hb05etSN8qZ
yo86aa1gs+8rSEn/GVO8UjX8Bh4NM/tff+yzMKWiWJGe9DtBvswSUPxBOU91vS8K
WcCpvWh9SpmAPyZEDWsZnTK7AUc+X2T+Soit+pJmLm9P3RxkvMqQxG82eMGVnooO
5aNe0T9zYLB4aB8unCJqPSYSLVDJ55vnC8tFIjcEhNCF/745gyMD/CrcQ4zCxdN/
KF6WEDc/XePF5qrHvkzWA7HiR0Xs9pDt3KugkU0enZV+cba0kKaBq230sZ++1KM=
=BwxN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is different enough to justify a split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We would like to allow other utlities to init msix and rx.
Put their declarations in a place accessible to other utilities.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If CONFIG_IPV6 is not enabled in the kernel, tcp.h is not included
implicitly from other header files, causing compilation errors. To
solve that, explicitly include it in tx-gen2.c.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The periphery can't be accessed before we set the
INIT_DONE bit which initializes the device.
A previous patch added a reconfiguration of the MSI-X
tables upon resume, but at that point in the flow,
INIT_DONE wasn't set. Since the reconfiguration of the
MSI-X tables require periphery access, it failed.
The difference between WoWLAN and without WoWLAN is that
in WoWLAN, iwl_trans_pcie_d3_suspend clears the INIT_DONE
without clearing the STATUS_DEVICE_ENABLED bit in the
software status. Because of that, the resume code thinks
that the device is enabled, but the INIT_DONE bit has been
cleared.
To fix this, don't reconfigure the MSI-X tables in case
WoWLAN is enabled. It will be done in
iwl_trans_pcie_d3_resume anyway.
Fixes: 52848a79b9 ("iwlwifi: pcie: reconfigure MSI-X HW on resume")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reading and dumping memory areas takes time, and sometimes
dumping all of the areas isn't necessary.
Allow choosing the memory areas which should be dumped.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Op mode will need this data in order to feed FW with it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes code less indented and more readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This allows less "dummy" declarations and casting.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The rfh for 22560 devices has changed so it supports now
the same arch of using used and free lists, but different
structures to support the last.
Use the new structures, hw dependent, to manage the lists.
bd, the free list, uses the iwl_rx_transfer_desc,
in which the vid is stored in the structs' rbid
field, and the page address in the addr field.
used_bd, the used list, uses the iwl_rx_completion_desc
struct, in which the vid is stored in the structs' rbid
field.
rb_stts, the hw "write" pointer of rx is stored in a
__le16 array, in which each entry represents the write
pointer per queue.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The smallest rb size supported today is 4k rx buffers.
22560 devices use 2k rxb's, so allow using 2k buffers.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22560 devices the firmware will do all the hw configurations,
but that's not ready yet.
Update the correct registers in the driver until the FW is ready
and does it by itself.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices RFH uses different structures, which act similar
to the legacy rxq management lists - free and used list.
The iwl_rx_transfer_desc struct is part of the free list,
and consists of pointers to the empty rb's the driver wants to
pass to the fw.
The iwl_rx_completion_desc struct is part of the used list,
and consists of pointers to the buffer the fw filled up
with new rx, both commands and data, for the host.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices use a new tx cmd api. Update the code to use
the new api.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices tfd queue max size is 2^16. Allow a configurable
max size in the driver for supporting different devices.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nowadays, the tfd queue max size is 2^8, and the reserved size in the
command header sequence field for the tfd entry index is 8 bits,
allowing an injective function from the hw pointers to the tfd entry index
in the sequence field.
In 22560 devices the tfd queue max size is 2^16, meaning that
the hw pointers are 16 bit long (allowing to point to each entry
in the tfd queue). However, the reserved space in the sequence field for
the tfd entry doesn't change, and we are limited to 8 bit.
This requires cancelling the injective function from hw pointer to
tfd entry in the sequence number.
Use iwl_pcie_get_cmd_index to wrap the hw pointer's to the n_window
size, which is maximum 256 in tx queues, and so, keep the injective
function between the window wrapped hw pointers to tfd entry index in
the sequence.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22560 devices the ROM sendis an interrupt to the host
once the IML reading is done.
Handle this interrupt, and indicate sw error in case the
value is fail.
Additionally, the cause for sw error in 22560 devices
have been changed, so update the cause list.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22560 devices we can start debug using context info gen3. Configure
the fw to start collecting logs to the dram before init.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For devices which use the image loader image, the length of the frame
must be updated in the byte count in bytes, and not dwords as today.
Avoid dividing the input length by 4.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Context information structure was added to 22000 devices for
firmware self init.
In the next generation of devices the context information
changes significantly, and the original context information
is divided roughly to three data structures: context information gen3,
prph information and prph scratch.
In addition, the init flow changes so the firmware is loaded
by the IML, and so we must allocate the IML on the DRAM and
give the ROM the IML's address before kicking the firmware's
self init.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The hw now refers to two new blocks:
* rx tr tail - The Tail index on the free buffers queue TR,
which is update by the device after reading the free buffer
from the tr.
* rx cr tail - Updated by the driver when completing
processing a new completion descriptor in the cr.
Add these two new struct to the rxq, allocate and free them
when needed.
In addition, the register for rx write pointer had been changed
to HBUS_TARG_WRPTR. The way to differentiate tx from rx is the
queue number. TX range is 0-511, and RX's is 512-527.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for the new 22560 family of devices and, while at it,
reorganize the 22000 family so it fits better with the new one.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new device IDs for the 9000 series.
Cc: stable@vger.kernel.org # 4.14
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbD/3rAAoJEG4XJFUm622b1ZwH/1xe1IqcwJXzfoDsYPlXVnSh
TiLExjKkD0ty5M0//844FxpxE1sSYJKOJ11uz/COzyG2qi4+5lgpUdjnDoINuKfH
ycqrXGssW7ogPWkVvnxKtlEYvkHNRYLQtxvd26umT77C69jVJLD0x9uihhh2En/C
EKs+OK1Pp0SRvTfB4AblWzoAnpEe1wHJFFh4i3F5H0lMGxLQz/YjFl5aeAjjR406
0vSKLGy2wKIydp8Pe4cAqBEeUWDJurn8ufkk7bmAET5zaXTH1qgZzLH3OWtx/ksz
mcPQq9/ctv35G2917t3Sn69SIUCDGfYkP5DiZV+ti0Hz2gIV0zOg7mGYCU8uHaU=
=11X5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the rx_allocator worker is canceled before running the
rx_init routine. rx_init frees and re-allocates all rxb's pages. The
rx_allocator worker also allocates pages for the used rxb's. Running
rx_init and rx_allocator simultaniously causes a kernel panic. Fix
that by canceling the work in rx_init.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently we have switched the csr addresses and values configuration
from a single configuration to all devices to a per-device configuration.
Doing that, the configuration for 6300 devices wasn't set.
This missing definition introduced a kernel panic once trying to access
the csr's.
Add the missing 6300 csr configuration.
While at it, add a checker that the csr values were indeed
configured, and bail out more gracefully if not.
Fixes: a8cbb46f83 ("iwlwifi: allow different csr flags for different device families")
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When there are 16 or more logical CPUs, we request for
`IWL_MAX_RX_HW_QUEUES` (16) IRQs only as we limit to that number of
IRQs, but later on we compare the number of IRQs returned to
nr_online_cpus+2 instead of max_irqs, the latter being what we
actually asked for. This ends up setting num_rx_queues to 17 which
causes lots of out-of-bounds array accesses later on.
Compare to max_irqs instead, and also add an assertion in case
num_rx_queues > IWM_MAX_RX_HW_QUEUES.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199551
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Hao Wei Tee <angelsl@in04.sg>
Tested-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we fail to to grab NIC access because the device is not responding
(i.e. CSR_GP_CNTRL returns 0xFFFFFFFF), remove the device from the PCI
bus, to avoid any further damage, and to let the user space rescan.
In order to inform the userspace that a rescan is needed, we send a
kobject uevent with "INACCESSIBLE".
This functionality is disabled by default, but can be enabled via a
new module parameter called "remove_when_gone". In the future we may
change this module parameter to include 3 modes instead: do nothing;
auto-rescan or; send uevent.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
In case of A-MSDUs, the trans layer is taking care of building
the subframes (out of the given skb), according to the given gso_size.
However, in some testing flows, we want to build the whole A-MSDU
frame in a different place (e.g. userspace), and ask the driver
to send it as-is.
In case of gso_size==0, simply treat the frame as normal-frame,
although the A-MSDU flag is set.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Different device families may have different flag values
for passing a message to the fw (i.e. SW_RESET).
In order to keep the code readable, and avoid conditioning
upon the family, store a value for each flag, which indicates
the bit that needs to be enabled.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid a race where two (or more) commands get the
same index:
1. T1 calls enqueue_hcmd and the local TFD index is assigned to
txq->write_ptr;
2. Context switch 'before incrementing txq->write_ptr';
3. T2 calls enqueue_hcmd and the local TFD index is assigned to
txq->write_ptr;
4. Now the index is set to the same value for both commands of T1 and
T2.
To prevent this from happening, set the local TFD index inside the
critical section (the index is set by global txq write pointer).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Op mode will begin tp use varying size of TX queue.
All the infra is in place, allow it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for dynamic queue sizing, add a parameter
of the TX queue size to the dynamic queue allocation op
mode API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit dd05f9aab4.
Shorter TX queues support was added eventually without the
need for the parameters this patch added.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When support for shorter TX queues was introduced, it
didn't include the actual allocation of shorter queue,
which is the main motive for the change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we enable TSO, we can have a lot of packets in the
operation mode that will be pushed to the transport
no matter what is the queue's fullness state.
To cope with that the transport can buffer those packets
and add them to the ring later when there is more room.
This implementation was missing in the Gen2 devices'
code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
