The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have two
conflicts this time:
CONFLICT (content): Merge conflict in net/mac80211/cfg.c
CONFLICT (content): Merge conflict in drivers/net/wireless/microchip/wilc1000/netdev.c
Here are Stephen's resolutions for them:
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au/https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au/
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* Enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZi07URHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZu3/QgAo7jyKgvpwMaNIVRLyfYCo0r3Q9wb7QPd
QeRNsftYxlWpPTJ4+Y95aZupy91Ay+RaEQXbbtl7PMIiyQrs7wb4V4Iqzedkws3t
DZsR5BitH+1BIGY0Omo0fiSB5HlWEwZGUj6inqlgKHpBtdIVTANSMjuwkdoMAV5y
ZU57axIGToySvDbRlhJQW833Nnh4KnaseA+TtyfXSaBVerzbshkjBr0d9pMBMiH9
irMQW5CW+7fbxp3OCNsKxX4eG6MFGmm/uP1hFmeYQi2qzUE4SddHMeV4I6oNKOrH
vFB+ZVmYvOjJUYsNhlCUe6Vy+EKwvmfiDWwE1egelEkgozCixJXAAQ==
=QT4C
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.11
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have
two conflicts this time:
net/mac80211/cfg.c
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au
drivers/net/wireless/microchip/wilc1000/netdev.c
https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA)
support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
* tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (194 commits)
wifi: ath12k: add hw_link_id in ath12k_pdev
wifi: ath12k: add panic handler
wifi: rtw89: chan: Use swap() in rtw89_swap_sub_entity()
wifi: brcm80211: remove unused structs
wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type)
wifi: ath12k: do not process consecutive RDDM event
dt-bindings: net: wireless: ath11k: Drop "qcom,ipq8074-wcss-pil" from example
wifi: ath12k: fix memory leak in ath12k_dp_rx_peer_frag_setup()
wifi: rtlwifi: handle return value of usb init TX/RX
wifi: rtlwifi: Enable the new rtl8192du driver
wifi: rtlwifi: Add rtl8192du/sw.c
wifi: rtlwifi: Constify rtl_hal_cfg.{ops,usb_interface_cfg} and rtl_priv.cfg
wifi: rtlwifi: Add rtl8192du/dm.{c,h}
wifi: rtlwifi: Add rtl8192du/fw.{c,h} and rtl8192du/led.{c,h}
wifi: rtlwifi: Add rtl8192du/rf.{c,h}
wifi: rtlwifi: Add rtl8192du/trx.{c,h}
wifi: rtlwifi: Add rtl8192du/phy.{c,h}
wifi: rtlwifi: Add rtl8192du/hw.{c,h}
wifi: rtlwifi: Add new members to struct rtl_priv for RTL8192DU
wifi: rtlwifi: Add rtl8192du/table.{c,h}
...
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Link: https://lore.kernel.org/r/20240607093517.41394C2BBFC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case the firmware sends a notification that claims it has more data
than it has, we will read past that was allocated for the notification.
Remove the print of the buffer, we won't see it by default. If needed,
we can see the content with tracing.
This was reported by KFENCE.
Fixes: bdccdb854f ("iwlwifi: mvm: support MFUART dump in case of MFUART assert")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.ba82a01a559e.Ia91dd20f5e1ca1ad380b95e68aebf2794f553d9b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When HW rfkill is toggled to disable the RF, the flow to stop scan is
called. When trying to send the command to abort the scan, since
HW rfkill is toggled, the command is not sent due to rfkill being
asserted, and -ERFKILL is returned from iwl_trans_send_cmd(), but this
is silently ignored in iwl_mvm_send_cmd() and thus the scan abort flow
continues to wait for scan complete notification and fails. Since it
fails, the UID to type mapping is not cleared, and thus a warning is
later fired when trying to stop the interface.
To fix this, modify the UMAC scan abort flow to force sending the
scan abort command even when in rfkill, so stop the FW from accessing
the radio etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.8cbe2f8c1a97.Iffe235c12a919dafec88eef399eb1f7bae2c5bdb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some versions of cfg80211, the ssids poinet might be a valid one even
though n_ssids is 0. Accessing the pointer in this case will cuase an
out-of-bound access. Fix this by checking n_ssids first.
Fixes: c1a7515393 ("iwlwifi: mvm: add adaptive dwell support")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240513132416.6e4d1762bf0d.I5a0e6cc8f02050a766db704d15594c61fe583d45@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ensure that the 6 GHz channel is configured with a valid direct BSSID,
avoiding any invalid or multicast BSSID addresses.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.91a631a0fe60.I2ea2616af9b8a2eaf959b156c69cf65a2f1204d4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When entering RF-kill, mac80211 tears down BA sessions, but
due to RF-kill the commands aren't sent to the device. As a
result, there can be frames pending on the reorder buffer or
perhaps even received while doing so, leading to warnings.
Avoid the warnings by doing the BA session teardown normally
even in RF-kill, which also requires queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.0762cd80fb3d.I43c5877f3b546159b2db4f36d6d956b333c41cf0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The BIGTK cipher field was added to the kek_kck_material_cmd
but wasn't assigned. Fix that by differentiating between the
IGTK/BIGTK keys and assign the ciphers fields accordingly.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.7fd0b22b7267.Ie9b581652b74bd7806980364d59e1b2e78e682c0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If pre-recovery mac80211 tried to disable a link but this disablement
failed, then there might be a mismatch between mac80211 assuming the
link has been disabled and the driver still having the data around.
During recover itself, that is not a problem, but should the link be
activated again at a later point, iwlwifi will refuse the activation as
it detects the inconsistent state.
Solve this corner-case by iterating the station in the restart cleanup
handler.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.d2fd60338055.I840d4fdce5fd49fe69896d928b071067e3730259@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the driver we only use skb_put* for adding data to the skb, hence data
never moves and skb_reset_mac_haeder would set mac_header to the first
time data was added and not to mac80211 header, fix this my using the
actual len of bytes added for setting the mac header.
Fixes: 3f7a9d577d ("wifi: iwlwifi: mvm: simplify by using SKB MAC header pointer")
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.12f2de2909c3.I72a819b96f2fe55bde192a8fd31a4b96c301aa73@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't actually support >64 even for HE devices, so revert
back to 64. This fixes an issue where the session is refused
because the queue is configured differently from the actual
session later.
Fixes: 514c30696f ("iwlwifi: add support for IEEE802.11ax")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.52f7b4cf83aa.If47e43adddf7fe250ed7f5571fbb35d8221c7c47@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After moving from commands to notificaitons in the d3 resume flow,
removing the WOWLAN_GET_STATUSES and REPLY_OFFLOADS_QUERY_CMD causes
the return of the default value when looking up their version.
Returning zero here results in the driver sending the not supported
NON_QOS_TX_COUNTER_CMD.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.8cabfd580614.If3a0db9851f56041f8f5360959354abd5379224a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since IWL_FW_CMD_VER_UNKNOWN = 99, then my change to consider
cmd_ver >= 7 instead of cmd_ver = 7 included also firmwares that don't
advertise the command version at all. This made us send a command with a
bad size and because of that, the firmware hit a BAD_COMMAND immediately
after handling the REDUCE_TX_POWER_CMD command.
Fixes: 8f892e225f ("wifi: iwlwifi: mvm: support iwl_dev_tx_power_cmd_v8")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512072733.eb20ff5050d3.Ie4fc6f5496cd296fd6ff20d15e98676f28a3cccd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In beacon template version 14, make sure to always set
the TWT IE offset before sending the beacon template command,
also in the debugfs inject_beacon_ie path.
If the TWT IE does not exist, the offset will be set to zero.
Fixes: bf0212fd8f ("wifi: iwlwifi: mvm: add beacon template version 14")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512152312.eb27175c345a.If30ef24aba10fe47fd42a7a9703eb8903035e294@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The initialization of this worker moved to iwl_mvm_mac_init_mvmvif
but we removed only from the pre-MLD version of the add_interface
callback. Remove it also from the MLD version.
Fixes: 0bcc215598 ("wifi: iwlwifi: mvm: init vif works only once")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240512152312.4f15b41604f0.Iec912158e5a706175531d3736d77d25adf02fba4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code that is parsing the amsdu_size module parameter and mapping it
to the corresponding Rx buffer size is common to all opmodes.
Move it into a function in iwlwifi, as preparation to a new op mode we
are working on.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240527190228.a3430d32923d.Iab3c22ef0df685f72f22dafc47021f0dc7bd6fa5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upon start, the different opmodes are currently printing:
1. HW rev, which is already print by iwlwifi
2. The HW name (e.g. "Intel(R) Wi-Fi 7 BE201 320MHz")
cleanup things such as the hw rev won't be printed again, the HW name will
be printed by iwlwifi instead of each opmode.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240527190228.5c589c7abed0.I3590c4ee0ee99d1b207852c32d25d326afb327dd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware prefix is unused today, but it might still be
useful to have some information. Since the prefix will get
the intel/ directory in some cases, replace the prefix by
the full FW id which has all the information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.527a1c72996d.If7588b854149d51605031fc9a70a650534351ef4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For active links, don't take information that may have been
received in probe responses, as those are not protected. For
inactive links, there may not be a choice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.6947dc462fa9.I2076961211d6785c8a15b4308e0e87a413148222@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Modify iwl_mvm_ftm_set_secured_ranging() parameters to support
multiple versions of the target struct.
This is done as preparation for moving to the new range request
version.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.56d6aee320b3.I5a52fa93cd791d0229b392a20f076b7cebb110cd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move setting the target's sta_id (and related flags) into a function
to support different versions of the target struct.
This is done as preparation for moving to the new range request
version.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.18e3a6a6f1cb.I85e3ee607b3947448532bc16730f8898a11c92b8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move setting the target flags into a dedicated function to support
different versions of the target struct.
This is done as preparation for moving to the new range request
version.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.9d22b61ce589.I7dbe596b4f677638d9a48c3f39b0826a9e35bea4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
6 GHz BSS SP client shall respect TX power limits advertised
by the AP in TPE elements, send the data to the firmware using
the AP_TX_POWER_CONSTRAINTS_CMD command, so do that.
Co-developed-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.32f1e2e1447c.I58ac91c38585362aa42bb4a8a59c7d88e67bc40b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the new RX_FLAG_MACTIME_IS_RTAP_TS64 in mac80211 to report
a 64-bit timestamp in the mactime for radiotap only, in case we
report the synchronized PTP clock timestamp (otherwise we really
only have 32 bits anyway).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.4fc44356e7df.Ic8642d35f1090a415e09299a1bd409f51dfb6351@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a debugfs option to use the ptp clock time for rx device
timestamps. This can be useful to e.g. synchronize multiple NICs or
reporting the timestamp in the system clock instead of gp2.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.b197b4f3f9ed.I578ee916d5f517a2e3a89e890a8ea24065946427@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we exit EMLSR due to a IWL_MVM_ESR_EXIT*, a MLO scan followed by a
link selection is scheduled with a delay of 30 seconds.
If during that 30 seconds EMLSR was blocked and unblocked
(IWL_MVM_ESR_BLOCKED*), we would still want to get the needed data from
the MLO scan and select link accordingly, and not return immediately to
EMLSR.
Fixes: 2f33561ea8 ("wifi: iwlwifi: mvm: trigger link selection after exiting EMLSR")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240512152312.caab27a8dd8f.I63f67e213d5e05416f71513a8d914917d59aa44f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we crash the firmware, we need to know why we decided to do so.
Almost all the callsites of iwl_force_nmi() print something in the logs
that explain why the driver decided to crash the firmware.
Debugfs doesn't print anything and it is then hard to understand why the
firmware has crashed.
Add a simple print in the debugfs hook to ease the debug.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512075822.e2558de222dc.Idd81777c47264e6f557b086625895c1dc2f667f3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When AUTO_EML is set to false, this change ignores the exit criteria,
for testing purposes. Currently, if AUTO_EML is disabled, the
driver will not select a link or enter EMLSR, but will still exit if one
of the criteria is not fulfilled.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240512072733.10a0b5da6ec2.I46fd578a3ef6cdbf14fdc4dfa97b4be008fe68e3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We track which link is using which FW link ID, so there
really isn't a need to separately track which link IDs
are in use. Remove that code and check the table when
looking for a new link ID to use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512072733.1a67d8af815f.Ie642c12dce3ab55c688abd9a25918569e83e558a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just like with any other frame, mac80211 will do sanity checks
on no-data RX (representing e.g. sounding PPDUs), and if e.g.
the NSS is wrong, it will warn. This isn't a good idea if we
already know the frame wasn't received well, e.g. has bad PLCP.
Unless the firmware reports "no error", set the bad PLCP flag
to skip checks in mac80211.
Also, since we're now extracting two different values from the
info field, use le32_get_bits() for both.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512072733.e6adcb9a6ece.Ic14c2e8ed5e80d48af78b2f04e9f08beeb62d68e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
fw_running assumes that memory can be retrieved only after alive.
This assumption is no longer true as we support dump before alive.
To avoid invalid access to the NIC, check that STATUS_DEVICE_ENABLED
bit in trans status is set before dumping instead of the prior check.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.ca07138cedeb.I090e31d3eaeb4ba19f5f84aba997ccd36927e9ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an entry for setting the maximum TXOP time in microseconds.
The configured value can be read from the same entry.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.b8d17a9c1731.I57c33574a61edd68bd0ec1aa7009f31111fd7efe@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
uAPSD can't be enabled on BSS or P2P Client if there is
another active interface (e.g. associated client). Allow
the code that apply those limitations to run on BSS as well.
Also forbid uAPSD if we have an IBSS or NAN interface in
the system.
Since we are now forbidding uAPSD in any concurrency
scenario, we don't need to check the number of PHY
contexts.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.4ac26534adf7.Ib892020177e86603b2be3a105f8717b9a15951d3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Avoid 'constexpr', which is a keyword in C23
- Allow 'dtbs_check' and 'dt_compatible_check' run independently of
'dt_binding_check'
- Fix weak references to avoid GOT entries in position-independent
code generation
- Convert the last use of 'optional' property in arch/sh/Kconfig
- Remove support for the 'optional' property in Kconfig
- Remove support for Clang's ThinLTO caching, which does not work with
the .incbin directive
- Change the semantics of $(src) so it always points to the source
directory, which fixes Makefile inconsistencies between upstream and
downstream
- Fix 'make tar-pkg' for RISC-V to produce a consistent package
- Provide reasonable default coverage for objtool, sanitizers, and
profilers
- Remove redundant OBJECT_FILES_NON_STANDARD, KASAN_SANITIZE, etc.
- Remove the last use of tristate choice in drivers/rapidio/Kconfig
- Various cleanups and fixes in Kconfig
-----BEGIN PGP SIGNATURE-----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=D5B/
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Avoid 'constexpr', which is a keyword in C23
- Allow 'dtbs_check' and 'dt_compatible_check' run independently of
'dt_binding_check'
- Fix weak references to avoid GOT entries in position-independent code
generation
- Convert the last use of 'optional' property in arch/sh/Kconfig
- Remove support for the 'optional' property in Kconfig
- Remove support for Clang's ThinLTO caching, which does not work with
the .incbin directive
- Change the semantics of $(src) so it always points to the source
directory, which fixes Makefile inconsistencies between upstream and
downstream
- Fix 'make tar-pkg' for RISC-V to produce a consistent package
- Provide reasonable default coverage for objtool, sanitizers, and
profilers
- Remove redundant OBJECT_FILES_NON_STANDARD, KASAN_SANITIZE, etc.
- Remove the last use of tristate choice in drivers/rapidio/Kconfig
- Various cleanups and fixes in Kconfig
* tag 'kbuild-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (46 commits)
kconfig: use sym_get_choice_menu() in sym_check_prop()
rapidio: remove choice for enumeration
kconfig: lxdialog: remove initialization with A_NORMAL
kconfig: m/nconf: merge two item_add_str() calls
kconfig: m/nconf: remove dead code to display value of bool choice
kconfig: m/nconf: remove dead code to display children of choice members
kconfig: gconf: show checkbox for choice correctly
kbuild: use GCOV_PROFILE and KCSAN_SANITIZE in scripts/Makefile.modfinal
Makefile: remove redundant tool coverage variables
kbuild: provide reasonable defaults for tool coverage
modules: Drop the .export_symbol section from the final modules
kconfig: use menu_list_for_each_sym() in sym_check_choice_deps()
kconfig: use sym_get_choice_menu() in conf_write_defconfig()
kconfig: add sym_get_choice_menu() helper
kconfig: turn defaults and additional prompt for choice members into error
kconfig: turn missing prompt for choice members into error
kconfig: turn conf_choice() into void function
kconfig: use linked list in sym_set_changed()
kconfig: gconf: use MENU_CHANGED instead of SYMBOL_CHANGED
kconfig: gconf: remove debug code
...
Kbuild conventionally uses $(obj)/ for generated files, and $(src)/ for
checked-in source files. It is merely a convention without any functional
difference. In fact, $(obj) and $(src) are exactly the same, as defined
in scripts/Makefile.build:
src := $(obj)
When the kernel is built in a separate output directory, $(src) does
not accurately reflect the source directory location. While Kbuild
resolves this discrepancy by specifying VPATH=$(srctree) to search for
source files, it does not cover all cases. For example, when adding a
header search path for local headers, -I$(srctree)/$(src) is typically
passed to the compiler.
This introduces inconsistency between upstream and downstream Makefiles
because $(src) is used instead of $(srctree)/$(src) for the latter.
To address this inconsistency, this commit changes the semantics of
$(src) so that it always points to the directory in the source tree.
Going forward, the variables used in Makefiles will have the following
meanings:
$(obj) - directory in the object tree
$(src) - directory in the source tree (changed by this commit)
$(objtree) - the top of the kernel object tree
$(srctree) - the top of the kernel source tree
Consequently, $(srctree)/$(src) in upstream Makefiles need to be replaced
with $(src).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
During restart mac80211 notifies the driver about the association,
(if we was associated before the restart) which causes the driver to
request statistics from the FW. This causes to an immediate exit from
EMLSR after the restart is done, when the statistics notif is handled.
(too low TPT). There is no point in requesting statistics wnyway, since
the FW just started and don't have any.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240506095953.16638dec9f7b.I093514312179bae566ad8d73ffb0355c6eee288a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware has different names for this, which is confusing
as even the convention of having the firmware name in a comment
after the struct definition wasn't met here. Fix the naming,
but keep UATS in some of it since that's the BIOS name.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.b0dfe17d5f44.I8f5f5a831c7b934ce3140f838315827c018103bb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While doing a passive scan, the firmware will report per-channel survey
information. This information is primarily useful for hostapd when doing
an ACS (Automatic Channel Selection). Collect this information and add
it to the result set when getting the survey information.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.9287591a5999.I54a3f9f6480d3694e67eea1cb4f5853beace2780@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When requested, the firmware can return per-channel survey information
generally used for ACS (automatic channel selection). Add the API for
this, which consists of a flag and a new channel survey notification.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.1facde532676.I3864ac4bc0fecb7fd5136e85c07585ab7100234b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The move of the scan complete notification handling to the wiphy worker
introduced a race between scan complete notification and scan abort:
- The wiphy lock is held, e.g., for rfkill handling etc.
- Scan complete notification is received but not handled yet.
- Scan abort is triggered, and scan abort is sent to the FW. Once the
scan abort command is sent successfully, the flow synchronously waits
for the scan complete notification. However, as the scan complete
notification was already received but not processed yet, this hangs for
a second and continues leaving the scan status in an inconsistent
state.
- Once scan complete handling is started (when the wiphy lock is not held)
since the scan status is not an inconsistent state, a warning is issued
and the scan complete notification is not handled.
To fix this issue, switch back the scan complete notification to be
asynchronously handling, and only move the link selection logic to
a worker (which was the original reason for the move to use wiphy lock).
While at it, refactor some prints to improve debug data.
Fixes: 07bf5297d3 ("wifi: iwlwifi: mvm: Implement new link selection algorithm")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.1f484a86324b.I63ed445a47f144546948c74ae6df85587fdb4ce3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a reading for all active EMLSR blocking reasons for testing
purposes.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.6d494a335e81.Ic0fa6a9636e3c1a3b1420e85e704a19d4a56e8d9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In iwl_mvm_rs_fw_rate_init() we have a variable cmd_id that
holds the command ID, so we can just use that instead of the
various calculations of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.f894ede03b26.I18f03c272b1c0807767f2713f3ffbb2941c57d9b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After restart, we might want to end up with the same config
as before, even for multi-link/EMLSR. Therefore, don't reset
the stored link selection result in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.e81db303f1dc.Ie8267082f623d14376a2052d222e18da6545f34b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there's an active link in a non-station vif, the station vif is
not allowed to enter EMLSR
Note that blocking EMLSR by calling iwl_mvm_block_esr() we will schedule
an exit from EMLSR worker, but the worker cannot run before the
activation of the non-BSS link, as ieee80211_remain_on_channel already
holds the wiphy mutex.
Handle that by explicitly calling ieee80211_set_active_links()
to leave EMLSR, and then doing iwl_mvm_block_esr() only for
consistency and to avoid re-entering it before ready.
Note that a call to ieee80211_set_active_links requires to release the
mvm mutex, but that's ok since we still hold the wiphy lock. The only
thing that might race here is the ESR_MODE_NOTIF, so this changes its
handler to run under the wiphy lock.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Co-developed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.916193759f8a.Idf3a3caf5cdc3e69c81710b7ceb57e87f2de87e4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If CSA is happening, then exit EMLSR to keep the better link,
which is the primary link unless that's doing the CSA with
quiet. This is done because we can't transmit the OMN frame
on a quiet link, but want to exit EMLSR during CSA for better
beacon reception, so we can follow the switch accurately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.3ffff9577f08.I2620971fa5aef789e0d4a588def4c2621e8bed5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new link selection algorithm uses defaults values for BSS load if
the BSS Load element was not published by the AP.
For 6 GHz, that value is 0. So if the best link is 6 GHz, the EMLSR
grade to always be equal to the grade of the best link,
and then the best link grade is getting a bonus of 10 percent, meaning
that we will never activate EMLSR.
Change the logic to not give a bonus for the best link.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.4614e6891dbd.Ie40eae0dd99d82ba60dea5b6dbcd42dcdf16b90d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When non default TTLM is applied, mac80211 may force us to use a specific
link (For example, if the only active link becomes a dormant link,
mac80211 will pick the first usable link and set it as active).
When default TTLM is applied, we have new usable links that we might want
to select. Therefore, trigger MLO scan and link selection upon change in
TTLM.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://msgid.link/20240505091420.ed2b386566a8.I0168e61da86b2027633743aaf5d97e483991f0dc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adjust EMLSR activation to account for traffic levels. By
tracking the number of RX/TX MPDUs, EMLSR will be activated only when
traffic volume meets the required threshold.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.9480f99ac8fc.If9eb946e929a39e10fe5f4638bc8bc3f8976edf1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an event occurs to unblock EMLSR, the code attempts to re-enable
EMLSR. However, the current implementation always tries to activate
EMLSR, regardless of whether the blocker was set before the unblocking
event or not. If EMLSR was already unblocked, there is no need to
re-activate it.
Fixes: 6cf7df9f01 ("wifi: iwlwifi: mvm: Add helper functions to update EMLSR status")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.eb861402dac9.I6a1d9f774f5551cfab60ea37b71a62640496af9b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
EMLSR can't be activated from mac80211. Except for the debugfs, which is
intended for testing purposes. Currently we don't allow entering EMLSR
from debugfs if EMLSR is blocked, i.e. if mvmvif::esr_disable_reason is
not 0. But we need a way to activate EMLSR regardless of the vif being
blocked, for testing. Remove the check of esr_disable_reason
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.bc3c24d9e0e6.Iad60e22a0d7e2b2b989051e1140b6dc98bef7bcc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the reason for exiting EMLSR was a blocking reason, wait for the
corresponding unblocking event:
- if there is an ongoing scan - do nothing. Link selection will be
triggered at the end of it.
- If more than 30 seconds passed since the exit, trigger MLO scan, which
will trigger link selection
- If less then 30 seconds passed since exit, reuse the latest link
selection result
If the reason for exiting EMLSR was an exit reason (IWL_MVM_EXIT_*),
schedule MLO scan in 30 seconds.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://msgid.link/20240505091420.6a808c4ae8f5.Ia79605838eb6deee9358bec633ef537f2653db92@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
BT Coex disables EMLSR only for a 2.4 GHz link, but doesn't block the
vif from using EMLSR with a different link pair. In addition, storing it
in mvmvif:disable_esr_reason requires extracting the BT Coex bit before
checking if EMLSR is blocked or not for a specific vif.
Therefore, change the BT Coex bit to be an exit reason and not a
blocker. On link selection, EMLSR mode will be re-calculated for the 2.4
GHz link instead of checking that bit.
While at it, move the relevant function declarations to the EMLSR
functions area in mvm.h
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.a2e93b67c895.I183a0039ef076613144648cc46fbe9ab3d47c574@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On older (pre-MLD API) devices, we started also calling
iwl_mvm_set_link_mapping()/iwl_mvm_unset_link_mapping(),
but of course not also iwl_mvm_remove_link(). Since the
link ID was only released in iwl_mvm_remove_link() this
causes us to run out of FW link IDs very quickly. Fix
it by releasing the link ID correctly.
Fixes: a8b5d4809b ("wifi: iwlwifi: mvm: Configure the link mapping for non-MLD FW")
Link: https://msgid.link/20240420154435.dce72db5d5e3.Ic40b454b24f1c7b380a1eedf67455d9cf2f58541@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the RSSI of a link is low enough, don't use it for EMLSR.
If EMLSR is already active and the RSSI of one of the links gets low,
exit EMLSR by deactivating that link.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.73263c000263.Ieb2b18855a2719b5e18ad2fa8a3e855ca4e23938@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can't be an EMLSR while suspended with wowlan. De-activate the
secondary link upon wowlan entring.
Set the blocking reason upon suspension and clear it upon resume.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.6ea884b3f095.I84233cb1c79ba538defafb8ddb983c47f04a400a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In EMLSR we need to track the RSSI of both links, and exit if the RSSI of
one of the links got too low.
For that request the FW to send statistics every 5 seconds when in EMLSR.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.6e19d596d77f.Ica2a75a031b1bced0dc2e18c5d365b5eb0d3ec07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 invokes the driver callback drv_can_activate_links() from
ieee80211_set_active_links to verify it can activate the desired link
combination.
However, ieee80211_set_active_links is called with more than one link in
2 cases:
- After driver's link selection decided to enter EMLSR
- From debugfs, for testing purposes.
For both cases there is no need to recompute all the considerations
determining whether to activate EMLSR.
Instead, only check if the vif is not blocked for EMLSR.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.202cf5a9ef2c.I65e4698b730a8652ad8d1c01420aabb41a1d04fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Address scenarios where repeated entry and exit from EMLSR occur, such as
encountering missed beacons on a specific link,
while still discovering that link during a scan.
To mitigate this, introduce the EMLSR prevention mechanism, which operates
as follows:
- On each exit from EMLSR event, record the timestamp and the exit
reason.
- If two consecutive exits happen for the same reason within a
400-second window, enforce a 300-second EMLSR prevention.
- If a third exit for the same reason occurs within 400 seconds from the
second exit, enforce an extended EMLSR prevention of 600 seconds.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.d820ee98b300.I6406db40cf25eabdba602afd783466473b909216@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's dangerous to re-initialize works repeatedly, especially
delayed ones that have an associated timer, and even more so
if they're not necessarily canceled inbetween. This can be
the case for these workers here during FW restart scenarios,
so make sure to initialize it only once.
While at it, also ensure it is cancelled correctly.
Fixes: f678061402 ("iwlwifi: mvm: disconnect in case of bad channel switch parameters")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.ddf8eece5eac.I4164f5c9c444b64a9abbaab14c23858713778e35@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are reasons for which we need to exit EMLSR, but not to block it
completely, and there are reasons for which we need to block EMLSR.
For both reason types we have the enum iwl_mvm_esr_state, when the
blocking reasons are stored in the `mvmvif::esr_disable_reason` bitmap.
This change introduces the APIs to use in the different cases:
- iwl_mvm_exit_esr - will exit from EMLSR mode.
- iwl_mvm_block_esr - will update the bitmap and exit EMLSR, to
be used for the blocking reasons only.
- iwl_mvm_unblock_esr - will update the bitmap. To be used for the
blocking reasons only.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.d54142a75876.I552926065521f5f848c37b0bd845494bd7865fb7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replaces the current logic with a new algorithm based on the link
grading introduced in a previous patch.
The new selection algorithm will be invoked upon successful scan to ensure
it has the necessary updated data it needs.
This update delegates the selection logic as the primary link
determiner in EMLSR mode, storing it in mvmvif to avoid repeated
calculations, as the result may vary.
Additionally, includes tests for iwl_mvm_valid_link_pair to validate
link pairs for EMLSR.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.309fb1b3fe44.I5baf0c293c89a5a28bd1a6386bf9ca6d2bf61ab8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The functions that are link related, so they should be in link.c and
not in mld-mac80211.c. Move them.
Also move the different prototypes to the right place in mvm.h
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.e7c368256fa0.I6b15805a7c8a75d1814f1a829601daf4d3788731@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currenty iwl_mvm_mld_select_links() doesn't fully check that
EMLSR is allowed before selecting the 2 best links.
Although it will fail in ieee80211_set_active_links(), it is preferred
to avoid the redundent calculations.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.3578a93feb1a.I1cd91608bb73fbe19b8dfdf90e14ce40b98c3430@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2.4 GHz/LB (low band) link can't be used in an EMLSR links pair when
BT is on. But EMLSR is still allowed for a pair of links which none of
them operates in LB.
In the existing code, EMLSR will always be disabled if one of the
usable links is in LB (and BT is on).
Move this check to the code that verifies a specific pair of links,
and only if one of these links operates on LB - disable EMLSR.
Fixes: 10159a4566 ("wifi: iwlwifi: disable eSR when BT is active")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.2841006b5cc4.I45ffd583f593daa950322852ceb9454cbf497e24@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function iwl_mvm_can_enter_esr() is (among others) calculating
if EMLSR mode is disabled due to BT coex by calling
iwl_mvm_bt_coex_calculate_esr_mode(), then stores the decision in
mvmvif::esr_disable_reason.
But there is no need to calculate this every time iwl_mvm_can_enter_esr
is called. Fix this by calculating it once after authorization,
and in iwl_mvm_can_enter_esr only check mvmvif::esr_disable_reason.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.a767e243366e.I3b32d36cda23f67dc103a28a9bdccb0039d22574@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For selecting what link(s) out of the usable ones
to activate, calculate a grade for a given link.
Calculation of a link grade is done as follows:
1. get the estimated throughput according to the RSSI of the link, this
will be the base grade
2. get the channel load from the BSS Load Element, subtracting the load
caused by us. Apply the factor on the grade.
3. puncturing factor: calculate the percentage of the punctured
subchannels (out of the total subchannels). Apply this on the grade.
The link grading will be used by the link selection mechanism in a later
patch.
Also add KUnit tests for it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.a6799dbd5643.If137ca6dc443606c7d8c99ec1fc38b325003a7c1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send AP_TX_POWER_CONSTRAINTS_CMD with no local maximum transmit
power constraint to FW and FW will update the TPE element with
required tx power limits.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.b6af4ecfcfe8.I07e8db349190e0c58c468c18477d8551288ac069@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will maintain a bitmap of reasons for which we want to avoid
enabling EMLSR.
For now, we have a single reason: BT coexistence, but we will add soon
more reasons. Make it a bitmap to make it easier to manage.
Since we'll impact the parameters that impact the enablement /
disablement of EMLSR from several places, introduce a generic function
that takes into account the current state and execute the decision that
must be taken.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.94c3590c6f27.I6a190da5025d0523ef483ffac0c64e26675041e6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for enable/disable 320 MHz for Japan and South Korea
by reading WBEM (WiFi Bandwidth Enablement per MCC) variable from
UEFI or ACPI and sending it to the FW.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415114847.7946c3befbe1.I453c33f7ea48156ea2a3961f50a9003103fca5a5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is useful in other places, so move it in order to share
it.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415114847.8e456d6c599e.Ibaa76864b30c990bfc35d886ec1344d513a96d14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of setting the UID to type mapping while building the
scan command, set the UID to type mapping only after the scan
request command was sent successfully.
This resolves a bug where in case a scan request command fails
and a recovery flow is initiated, the recovery flow would indicate
to mac80211 that scan is completed though it was not really started.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415114847.7011e93363a2.Idb9b401414864dfc5540d8798a6cb2b192a2acc2@changeid
[also remove from iwl_mvm_scan_umac_v14_and_above()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is supposed to return a uid on success, and an errno in
failure.
But it currently returns the return value of the specific cmd version
handler, which in turn returns 0 on success and errno otherwise.
This means that on success, iwl_mvm_build_scan_cmd will return 0
regardless if the actual uid.
Fix this by returning the uid if the handler succeeded.
Fixes: 687db6ff5b ("iwlwifi: scan: make new scan req versioning flow")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://msgid.link/20240415114847.5e2d602b3190.I4c4931021be74a67a869384c8f8ee7463e0c7857@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a PASN station is added, and an old PASN station already exists
for the same mac address, remove the old station before adding the
new one. Keeping the old station caueses old security context to
be used in measurements.
Fixes: 0739a7d70e ("iwlwifi: mvm: initiator: add option for adding a PASN responder")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415114847.ef3544a416f2.I4e8c7c8ca22737f4f908ae5cd4fc0b920c703dd3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The first "new features" pull request for v6.10 with changes both in
stack and in drivers. The big thing in this pull request is that
wireless subsystem is now almost free of sparse warnings. There's only
one warning left in ath11k which was introduced in v6.9-rc1 and will
be fixed via the wireless tree.
Realtek drivers continue to improve, now we have support for RTL8922AE
and RTL8723CS devices. ath11k also has long waited support for P2P.
This time we have a small conflict in iwlwifi as we didn't consider it
as major enough to justify merging wireless tree to wireless-next. But
Stephen has an example merge resolution which should help with fixing
the conflict:
https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/
Major changes:
rtw89
* RTL8922AE Wi-Fi 7 PCI device support
rtw88
* RTL8723CS SDIO device support
iwlwifi
* don't support puncturing in 5 GHz
* support monitor mode on passive channels
* BZ-W device support
* P2P with HE/EHT support
ath11k
* P2P support for QCA6390, WCN6855 and QCA2066
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmYNIqIRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt8jAf9H+o91boD34/qVdI5LWEcFhVKEkHpNtwm
Y1sTKNBEtN1Gs2zcljjO6PqN9N4v2+lA42KSpzP5M42FfpI2aATI2v8jYsKTXOl2
YVwF+8pDiAsi0YtQTxIthygjzTpsePCfj8z0xJaKGm195T+fMm9UebYETrfxxOp/
z5StsJIPI0twgSLKKUWvLpX4ESt0l0HLJY1ok99sk4Cj36EKn6b9LbBinDKr6GcQ
mGNtPyq0j4l0kS5qae9BbXZUohO54o8wiFnApdwGfA7S/kLY7eUtwZy7T050b62P
zbNafwZbIjrH7dNcGfe6Fdr7PjQYFeI5Nh7dXxqM2LJOQsYXU/tcWQ==
=WrPE
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.10
The first "new features" pull request for v6.10 with changes both in
stack and in drivers. The big thing in this pull request is that
wireless subsystem is now almost free of sparse warnings. There's only
one warning left in ath11k which was introduced in v6.9-rc1 and will
be fixed via the wireless tree.
Realtek drivers continue to improve, now we have support for RTL8922AE
and RTL8723CS devices. ath11k also has long waited support for P2P.
This time we have a small conflict in iwlwifi, Stephen has an example
merge resolution which should help with fixing the conflict:
https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/
Major changes:
rtw89
* RTL8922AE Wi-Fi 7 PCI device support
rtw88
* RTL8723CS SDIO device support
iwlwifi
* don't support puncturing in 5 GHz
* support monitor mode on passive channels
* BZ-W device support
* P2P with HE/EHT support
ath11k
* P2P support for QCA6390, WCN6855 and QCA2066
* tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (122 commits)
wifi: mt76: mt7915: workaround dubious x | !y warning
wifi: mwl8k: Avoid -Wflex-array-member-not-at-end warnings
wifi: ti: Avoid a hundred -Wflex-array-member-not-at-end warnings
wifi: iwlwifi: mvm: fix check in iwl_mvm_sta_fw_id_mask
net: rfkill: gpio: Convert to platform remove callback returning void
wifi: mac80211: use kvcalloc() for codel vars
wifi: iwlwifi: reconfigure TLC during HW restart
wifi: iwlwifi: mvm: don't change BA sessions during restart
wifi: iwlwifi: mvm: select STA mask only for active links
wifi: iwlwifi: mvm: set wider BW OFDMA ignore correctly
wifi: iwlwifi: Add support for LARI_CONFIG_CHANGE_CMD cmd v9
wifi: iwlwifi: mvm: Declare HE/EHT capabilities support for P2P interfaces
wifi: iwlwifi: mvm: Remove outdated comment
wifi: iwlwifi: add support for BZ_W
wifi: iwlwifi: Print a specific device name.
wifi: iwlwifi: remove wrong CRF_IDs
wifi: iwlwifi: remove devices that never came out
wifi: iwlwifi: mvm: mark EMLSR disabled in cleanup iterator
wifi: iwlwifi: mvm: fix active link counting during recovery
wifi: iwlwifi: mvm: assign link STA ID lookups during restart
...
====================
Link: https://lore.kernel.org/r/20240403093625.CF515C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The first fixes for v6.9. Ping-Ke Shih now maintains a separate tree
for Realtek drivers, document that in the MAINTAINERS. Plenty of fixes
for both to stack and iwlwifi. Our kunit tests were working only on um
architecture but that's fixed now.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmYEbzoRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZsjZwgApoOcTn/mkX7DEViByMUpOrdNYqkJh+Tv
RkDDqhbA97i+zlxWp1dwtdfn0CYEcCW2XBucrfDNZMcR/cfXy2Wgdr6BD/FG9S2D
oQX6QQijO7g9uqNgDfIVAC0ftJEeWkM7YUhqNDVR751gjy2WOOJqPtSgNGd873By
P0rbHyfykHMzyYbwlzMLosO3RigefD1p1qkkODPf2OMo5A4tL1gL9AfEk3Kef9sf
9JHHWCLR378sm2sMpGw2Lxw4ypazl08ABu1yAWJk6Xipn80D/b08YUH/1yiKuq22
JrxhllJu2nqaHxXOzje2WEapTBz9tpTAwigOUQJiVZWm6ii19giGng==
=89Ft
-----END PGP SIGNATURE-----
Merge tag 'wireless-2024-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.9-rc2
The first fixes for v6.9. Ping-Ke Shih now maintains a separate tree
for Realtek drivers, document that in the MAINTAINERS. Plenty of fixes
for both to stack and iwlwifi. Our kunit tests were working only on um
architecture but that's fixed now.
* tag 'wireless-2024-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (21 commits)
MAINTAINERS: wifi: mwifiex: add Francesco as reviewer
kunit: fix wireless test dependencies
wifi: iwlwifi: mvm: include link ID when releasing frames
wifi: iwlwifi: mvm: handle debugfs names more carefully
wifi: iwlwifi: mvm: guard against invalid STA ID on removal
wifi: iwlwifi: read txq->read_ptr under lock
wifi: iwlwifi: fw: don't always use FW dump trig
wifi: iwlwifi: mvm: rfi: fix potential response leaks
wifi: mac80211: correctly set active links upon TTLM
wifi: iwlwifi: mvm: Configure the link mapping for non-MLD FW
wifi: iwlwifi: mvm: consider having one active link
wifi: iwlwifi: mvm: pick the version of SESSION_PROTECTION_NOTIF
wifi: mac80211: fix prep_connection error path
wifi: cfg80211: fix rdev_dump_mpp() arguments order
wifi: iwlwifi: mvm: disable MLO for the time being
wifi: cfg80211: add a flag to disable wireless extensions
wifi: mac80211: fix ieee80211_bss_*_flags kernel-doc
wifi: mac80211: check/clear fast rx for non-4addr sta VLAN changes
wifi: mac80211: fix mlme_link_id_dbg()
MAINTAINERS: wifi: add git tree for Realtek WiFi drivers
...
====================
Link: https://lore.kernel.org/r/20240327191346.1A1EAC433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the previous commit, I renamed the variable to differentiate
mac80211/mvm link STA, but forgot to adjust the check. The one
from mac80211 is already non-NULL anyway, but the mvm one can
be NULL when the mac80211 isn't during link switch conditions.
Fix the check.
Fixes: 2783ab506e ("wifi: iwlwifi: mvm: select STA mask only for active links")
Reviewed-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240325180850.e95b442bafe9.I8c0119fce7b00cb4f65782930d2c167ed5dd0a6e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the HW restart flow with multi-link is very similar to
the initial association, we do need to reconfigure TLC there.
Remove the check that prevented that.
Fixes: d2d0468f60 ("wifi: iwlwifi: mvm: configure TLC on link activation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.a00adcfe381a.Ic798beccbb7b7d852dc976d539205353588853b0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During restart, we haven't added BA sessions, so we also cannot
change them to switch between links when that happens in restart.
Short-circuit the appropriate function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.70ba08540db0.Ic604d384e660c755308a49a79d3f7e78bc27597c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During reconfig, we might send keys, but those should be only
sent to already active link stations. Iterate only active ones
to fix that issue.
Fixes: aea99650f7 ("wifi: iwlwifi: mvm: set STA mask for keys in MLO")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.c6818d1c6033.I6357f05c55ef111002ddc169287eb356ca0c1b21@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clearly, I put this flag into the wrong place: devices using the
code in mac80211.c only do not support EHT, so this isn't even
relevant. Fix this by moving the code to the right function.
Fixes: 32a5690e9a ("wifi: iwlwifi: mvm: support wider-bandwidth OFDMA")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.0d5fb0e971e4.I3b67c5e0ddcbe6e58143ec0bc4e40dd6dba4f863@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a requirement from OEMs to support new bits in DSM function 7,
which will indicate enablement of 5.9 GHz in Canada.
Add support for this by reading those bits from BIOS and sending it to the
FW. mask unii4 allow bitmap based on LARI_CONFIG_CHANGE_CMD version
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.5c31ccd73119.I0363992efc3607368648d34a7918b2534150a3ca@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This comment was added when iwl_mvm_alloc_sta_after_restart configured
the FW with an internal station, but then it was changed by
164a52d45e ("wifi: iwlwifi: mvm: send full STA during HW restart")
to configure the full sta, So there is no reason to "wait for mac80211 to
add the STA" as this is exacly where it happens.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240320232419.d656c2385b06.Icccd0640eb9f1ad72ff74792086435dfc0bee6eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During HW restart only one link will be active initially and other links
are only activated again later on. With only a single link EMLSR cannot
be enabled and having it marked enabled confuses the internal state.
Mark EMLSR as disabled in the cleanup iterator, it can be reenabled
later one once this is possible.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.71eb622d6ce3.Ic4d50695b9bb332190dc712473096083aa96074b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During recovery, the chanctx_conf in mac80211 is still non-NULL even
though the channel context has not yet been assigned again. In that
case, the real count is actually lower.
Switch to instead count the phy_ctx assignment and ensure that the
assignment is cleared at the start of recovery.
Fixes: 12bacfc2c0 ("wifi: iwlwifi: handle eSR transitions")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.55f37339e7d1.I57006568a90ffb7a1232def1b2f3264dea711ba6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When restarting the HW, mac80211 first adds the STA back with only one
link enabled. This means that iwl_mvm_alloc_sta_after_restart will not
see the other links and will not do the assignment.
As such, do the assignment when mac80211 is activating the link for the
station.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.4a3273e5c6be.I7cb6cf096ab135f4b489f2806b116563624aa5ee@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the mvm driver, data structures match what's in the firmware,
we allocate FW IDs for them already etc. During link switch we
already allocate/free the STA links appropriately, but initially
we'd allocate them always. Fix this to allocate memory, a STA ID,
etc. only for active links.
Fixes: 57974a55d9 ("wifi: iwlwifi: mvm: refactor iwl_mvm_mac_sta_state_common()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.f2093ff73465.Ie891e1cc9c9df09ae22be6aad5c143e376f40f0e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As it is possible that by the time the scan is completed the link was
already removed.
Fixes: 3a5a5cb067 ("wifi: iwlwifi: mvm: Correctly report TSF data in scan complete")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.619d3574a757.I0523e92547f0288c8b0119b1fdc5e967a5a8956e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When scanning on 6 GHz we allocate a set of short-SSIDs and BSSIDs to
probe. However, when we need to do an active scan because of a hidden
SSID, then we could add too many entries for probing causing an
assertion in the firmware input validation.
Reshuffle the code a bit to first calculate the maximum number of
short-SSIDs and BSSIDs that are permitted for the channel. Then ensure
that we do not set more than the permitted number of bits in the
bitmasks and turn on force_passive when we have surpassed the limit.
While at it, also change the logic so that allow_passive is always
disabled in case a hidden SSID is included. Previously, we might not
have done so if we added the short-SSID based on the number of BSSIDs
already in the request.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.e0b114b68d1d.Ib86afccdb955f0d221ef5d7b8afdc1d67c3542ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an option to force sending unprotected ranging request even if the
station is associated to the responder or a PASN keys are configured.
This is used for testing.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.8523150148ec.I7ab6c547513717e69ec385f72a8f43ea00bd9e0a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new scan type that can be used for internal MLO purposes, i.e.,
in case updated BSS information is required. Currently only passive
scanning is supported.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.5ce3e756cf8f.I4a41065f6b3a6ec6c6e44e83bc97c277ff7c599e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support staring internal scan, refactor the scan code such
that the body iwl_mvm_reg_scan_start() is now moved to a local
function that can be used by other flows as well.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.e7833d4cfc53.I43c1c533c2a5243229002fde6360d423946c54fa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware has handled quiet in CSA for a long time now, but
it didn't really matter much. However, now with quiet CSA on a
perhaps secondary link, we don't want mac80211 to stop queues,
we can continue using a link that's not requiring quiet. Set
the feature flag for MLO-capable devices indicating that we'll
handle the quiet entirely in the driver/device.
However, the firmware doesn't handle quiet in AP mode since we
don't really expect to really be needing that (without radar
detection), but - even for testing - make that work properly
by simply not pulling from TXQs in this scenario.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.fa75403b5eaa.Ie3ff02215f810fcfefd6a22c481567f94f61c0c6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If, for any reason, we're going to attempt to flush the queues
while quiet CSA is happening, this cannot succeed. This could
be the case if for example mac80211 were to flush after TXing
e.g. a deauth frame due to disconnecting during the CSA.
In this case, drop the frames instead, the firmware won't let
us do any transmissions and may also become unhappy if we're
not going to disconnect quickly enough.
Currently this doesn't happen as mac80211 stops queues, but
we'll want to let mac80211 know not to stop queues for proper
multi-link support during CSA, so we need to handle this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.d5d629f32ea8.I86d9b849d92273542bfc2d9c671b66179e7ebb72@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In version 4, in case of MLO GTK rekey during D3,
the firmware sends all the new keys, including
the keys on the non-active links.
Update also the non active link keys.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.6524de988ed3.Id065ddd2f4a71b0243c33ae0c5476ac41bfe2dc2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When waking up from wowlan, we iterate over the current
keys and remove those that were rekeyed.
With MLO, there might be keys of other links which should
not be removed.
Skip MLO keys on other links (other than the wowlan
active link).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.fdf527b50d61.I605a971d2d68107769dd363b896b471998259e64@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, the station id in d3 can be other than 0.
Do not assume the station id is 0 when waking
up from d3.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.6379619f2987.I83de9d868224df76eee8df8dbcf352636535821a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With MLO, the station id in wowlan can be other than 0.
Set the correct station in the protocol offload command.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.ace4f793872d.Id984110576a72acc84493217ca95564c3cd362bd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When releasing frames from the reorder buffer, the link ID was not
included in the RX status information. This subsequently led mac80211 to
drop the frame. Change it so that the link information is set
immediately when possible so that it doesn't not need to be filled in
anymore when submitting the frame to mac80211.
Fixes: b8a85a1d42 ("wifi: iwlwifi: mvm: rxmq: report link ID to mac80211")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.bbbd5e9bfe80.Iec1bf5c884e371f7bc5ea2534ed9ea8d3f2c0bf6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With debugfs=off, we can get here with the dbgfs_dir being
an ERR_PTR(). Instead of checking for all this, which is
often flagged as a mistake, simply handle the names here
more carefully by printing them, then we don't need extra
checks.
Also, while checking, I noticed theoretically 'buf' is too
small, so fix that size as well.
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218422
Fixes: c36235acb3 ("wifi: iwlwifi: mvm: rework debugfs handling")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.4dc1eb3dd015.I32f308b0356ef5bcf8d188dd98ce9b210e3ab9fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Guard against invalid station IDs in iwl_mvm_mld_rm_sta_id as that would
result in out-of-bounds array accesses. This prevents issues should the
driver get into a bad state during error handling.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.d523167bda9c.I1cffd86363805bf86a95d8bdfd4b438bb54baddc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the rx payload length check fails, or if kmemdup() fails,
we still need to free the command response. Fix that.
Fixes: 21254908cb ("iwlwifi: mvm: add RFI-M support")
Co-authored-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.db2fa0196aa7.I116293b132502ac68a65527330fa37799694b79c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the non MLD firmware flows, although the deflink is used, the mapping
of link ID to BSS configuration was missing, which causes flows that need
this mapping to crash.
Fix this by adding the link ID to BSS configuration mapping to non MLD
flows as well.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.0b5c361e8f0c.Ib11f41815d2efa5d1ec57f855de4c8563142987b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not call iwl_mvm_mld_get_primary_link if only one link
is active.
In that case, the sole active link should be used.
iwl_mvm_mld_get_primary_link returns -1 if only one link
is active causing a warning.
Fixes: 8c9bef26e9 ("wifi: iwlwifi: mvm: d3: implement suspend with MLO")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.6c50061bf69b.I05b0ac7fa7149eabaa5570a6f65b0d9bfb09a6f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MLO ended up not really fully stable yet, we want to make
sure it works well with the ecosystem before enabling it.
Thus, remove the flag, but set WIPHY_FLAG_DISABLE_WEXT so
we don't get wireless extensions back until we enable MLO
for this hardware.
Cc: stable@vger.kernel.org
Reviewed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240314110951.d6ad146df98d.I47127e4fdbdef89e4ccf7483641570ee7871d4e6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Store zone trips table and zone operations directly in struct
thermal_zone_device (Rafael Wysocki).
- Fix up flex array initialization during thermal zone device
registration (Nathan Chancellor).
- Rework writable trip points handling in the thermal core and
several drivers (Rafael Wysocki).
- Thermal core code cleanups (Dan Carpenter, Flavio Suligoi).
- Use thermal zone accessor functions in the int340x Intel thermal
driver (Rafael Wysocki).
- Add Lunar Lake-M PCI ID to the int340x Intel thermal driver (Srinivas
Pandruvada).
- Minor fixes for thermal governors (Rafael Wysocki, Di Shen).
- Trip point handling fixes for the iwlwifi wireless driver (Rafael
Wysocki).
- Code cleanups (Rafael J. Wysocki, AngeloGioacchino Del Regno).
-----BEGIN PGP SIGNATURE-----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=Is/Y
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These mostly change the thermal core in a few ways allowing thermal
drivers to be simplified, in particular in their removal and failing
probe handling parts that are notoriously prone to errors, and
propagate the changes to several drivers.
Apart from that, support for a new platform is added (Intel Lunar
Lake-M), some bugs are fixed and some code is cleaned up, as usual.
Specifics:
- Store zone trips table and zone operations directly in struct
thermal_zone_device (Rafael Wysocki)
- Fix up flex array initialization during thermal zone device
registration (Nathan Chancellor)
- Rework writable trip points handling in the thermal core and
several drivers (Rafael Wysocki)
- Thermal core code cleanups (Dan Carpenter, Flavio Suligoi)
- Use thermal zone accessor functions in the int340x Intel thermal
driver (Rafael Wysocki)
- Add Lunar Lake-M PCI ID to the int340x Intel thermal driver
(Srinivas Pandruvada)
- Minor fixes for thermal governors (Rafael Wysocki, Di Shen)
- Trip point handling fixes for the iwlwifi wireless driver (Rafael
Wysocki)
- Code cleanups (Rafael J. Wysocki, AngeloGioacchino Del Regno)"
* tag 'thermal-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (29 commits)
thermal: core: remove unnecessary check in trip_point_hyst_store()
thermal: intel: int340x_thermal: Use thermal zone accessor functions
thermal: core: Remove excess empty line from a comment
thermal: int340x: processor_thermal: Add Lunar Lake-M PCI ID
thermal: core: Eliminate writable trip points masks
thermal: of: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: imx: Set THERMAL_TRIP_FLAG_RW_TEMP directly
wifi: iwlwifi: mvm: Set THERMAL_TRIP_FLAG_RW_TEMP directly
mlxsw: core_thermal: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: intel: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: core: Drop the .set_trip_hyst() thermal zone operation
thermal: core: Add flags to struct thermal_trip
thermal: core: Move initial num_trips assignment before memcpy()
thermal: Get rid of CONFIG_THERMAL_WRITABLE_TRIPS
thermal: intel: Adjust ops handling during thermal zone registration
thermal: ACPI: Constify acpi_thermal_zone_ops
thermal: core: Store zone ops in struct thermal_zone_device
thermal: intel: Discard trip tables after zone registration
thermal: ACPI: Discard trips table after zone registration
thermal: core: Store zone trips table in struct thermal_zone_device
...
The fourth "new features" pull request for v6.9 with changes both in
stack and in drivers. The theme in this pull request is to fix sparse
warnings but we still have some left in wireless subsystem. Otherwise
quite normal.
Major changes:
rtw89
* NL80211_EXT_FEATURE_SCAN_RANDOM_SN support
* NL80211_EXT_FEATURE_SET_SCAN_DWELL support
rtw88
* support for more rtw8811cu and rtw8821cu devices
mt76
* mt76x2u: add Netgear WNDA3100v3 USB
* mt7915: newer ADIE version support
* mt7925: radio temperature sensor support
* mt7996: remove GCMP IGTK offload
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmXq4hARHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtOawf9Gf2FAi56zA/4vKJPE/mZzRvNodj/u9WL
mEX3KERw744IEmWY0yXEAyvzKkkNqUUtmdUbbsnXnnEtzsVZ2oRmOZdXsvEW3vOD
IEsjWY/405MBWyuBttAa6orBSgelr99k86HzoLN86s52HmliVDhr2EUnYIf2O++9
SVhHFKE4BMVCO6hlyEg419K9M2VhWtBDNYweoXAfn8Y1byAw6Pt6WunjRuGwJG5n
qvcrZcFCFSa3daPpx0uIA/yiSjZlq0hwVC3r/PnoX/r1FDR8tS2ecvC2rP3MaZJ+
1x3IcNvwC97D80wvdW+f+qKtV4OXZefsZpzJJpvREH8FbAgYLDef0Q==
=gln7
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The fourth "new features" pull request for v6.9 with changes both in
stack and in drivers. The theme in this pull request is to fix sparse
warnings but we still have some left in wireless subsystem. Otherwise
quite normal.
Major changes:
rtw89
* NL80211_EXT_FEATURE_SCAN_RANDOM_SN support
* NL80211_EXT_FEATURE_SET_SCAN_DWELL support
rtw88
* support for more rtw8811cu and rtw8821cu devices
mt76
* mt76x2u: add Netgear WNDA3100v3 USB
* mt7915: newer ADIE version support
* mt7925: radio temperature sensor support
* mt7996: remove GCMP IGTK offload
* tag 'wireless-next-2024-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (125 commits)
wifi: rtw89: wow: move release offload packet earlier for WoWLAN mode
wifi: rtw89: wow: set security engine options for 802.11ax chips only
wifi: rtw89: update suspend/resume for different generation
wifi: rtw89: wow: update config mac function with different generation
wifi: rtw89: update DMA function with different generation
wifi: rtw89: wow: update WoWLAN status register for different generation
wifi: rtw89: wow: update WoWLAN reason register for different chips
wifi: brcm80211: handle pmk_op allocation failure
wifi: rtw89: coex: Add coexistence policy to decrease WiFi packet CRC-ERR
wifi: rtw89: coex: When Bluetooth not available don't set power/gain
wifi: rtw89: coex: add return value to ensure H2C command is success or not
wifi: rtw89: coex: Reorder H2C command index to align with firmware
wifi: rtw89: coex: add BTC ctrl_info version 7 and related logic
wifi: rtw89: coex: add init_info H2C command format version 7
wifi: rtw89: 8922a: add coexistence helpers of SW grant
wifi: rtw89: mac: add coexistence helpers {cfg/get}_plt
wifi: cw1200: restore endian swapping
wifi: wlcore: sdio: Rate limit wl12xx_sdio_raw_{read,write}() failures warns
wifi: rtlwifi: Remove rtl_intf_ops.read_efuse_byte
wifi: rtw88: 8821c: Fix false alarm count
...
====================
Link: https://lore.kernel.org/r/20240308100429.B8EA2C433F1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the link conf to the abort_channel_switch driver
method so the driver can handle things correctly.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095718.27f621106ddd.Iadd3d69b722ffe5934779a32a0e4e596a4e33ed4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, we need the link id in the GTK key to be given by
the driver after rekeying in wowlan, so add that.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094500.ce1bfc83a680.I43a6f8ab2804ee07116a37d5b9ec601b843464b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
(skb_transport_header(skb) - skb_network_header(skb))
can be replaced by skb_network_header_len(skb)
Add a DEBUG_NET_WARN_ON_ONCE() in skb_network_header_len()
to catch cases were the transport_header was not set.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the thermal_zone_device_register_with_trips() callers pass zero
writable trip points masks to it, so drop the mask argument from that
function and update all of its callers accordingly.
This also removes the artificial trip points per zone limit of 32,
related to using writable trip points masks.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It is now possible to flag trip points with THERMAL_TRIP_FLAG_RW_TEMP
to allow their temperature to be set from user space via sysfs instead
of using a nonzero writable trips mask during thermal zone registration,
so make the iwlwifi code do that.
No intentional functional impact.
Note that this change is requisite for dropping the mask argument from
thermal_zone_device_register_with_trips() going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Merge thermal core changes for 6.9:
- Minor fixes for thermal governors (Rafael J. Wysocki, Di Shen).
- Trip point handling fixes for the iwlwifi wireless driver (Rafael J.
Wysocki).
- Code cleanups (Rafael J. Wysocki, AngeloGioacchino Del Regno).
* thermal-tmp:
thermal: gov_power_allocator: Avoid overwriting PID coefficients from setup time
thermal: sysfs: Fix up white space in trip_point_temp_store()
iwlwifi: mvm: Use for_each_thermal_trip() for walking trip points
iwlwifi: mvm: Populate trip table before registering thermal zone
iwlwifi: mvm: Drop unused fw_trips_index[] from iwl_mvm_thermal_device
thermal: core: Change governor name to const char pointer
thermal: gov_bang_bang: Fix possible cooling device state ping-pong
thermal: gov_fair_share: Fix dependency on trip points ordering
In the operational statistics notifications (both old and new
API) the driver receives the statistics per phy.
currently this statistics wasn't handled because they wasn't needed.
Now the channel_load_by_us parameter in these statistics will be used
for the link grading calculation (implemented in another patch),
so store its value in phy_ctxt.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240218194912.e84f975b69ee.Ibbc7817135827e45adaaa47b796be165f9f1ca48@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At that point in the code mvm->mutex has already been taken, so jump to
out_noreset in order to unlock before returning the error.
Fixes: 8c9bef26e9 ("wifi: iwlwifi: mvm: d3: implement suspend with MLO")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240218194912.21de6e68d9e5.I3c0ebe577dec6b26ab6b4eac48035d6f35a8b0f8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fill the new puncture mask in the PHY context command if
supported. In this case, also don't send it in the link
context command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240218194912.16d9f5fc41df.I9eeb55787d8483f820f5790e8874761f598da314@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The version 6 command adds the puncture mask to the PHY
context and is otherwise the same. Support that in the
API definitions, but don't fill it yet.
While at it, also mark the field as removed from the link
context command since it moved from there to PHY context.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240218194912.2156fca5b1a5.I57f47f26ec0d96ecfb1192039f72b1c6d4e8a357@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support wider-bandwidth OFDMA we need to configure the
PHY context in the firmware, which will in turn configure
the DSP accordingly. Pass the relevant information down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240218194912.ca666ede5dd6.I357972823d20e9045e2c97dbb7ac24fe9f5a6e41@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, function to check if beacon countdown is complete uses deflink
to fetch the beacon and check the counter. However, with MLO, there is
a need to check the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240216144621.514385-2-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Those devices' fifos are numbered differently.
Because of that, we were looking at the size of the VO fifo size to
determine the size of the A-MSDU which led to a lower throughput.
Note that for those devices the only user of the AC -> fifo mapping is
the size limitation of A-MSDU.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240218194912.da336ca2fa0a.I73e44d5fc474ebb6f275b9008950e59c012f33b2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The resume code path assumes that the TX queue for the offloading TID
has been configured. At resume time it then tries to sync the write
pointer as it may have been updated by the firmware.
In the unusual event that no packets have been send on TID 0, the queue
will not have been allocated and this causes a crash. Fix this by
ensuring the queue exist at suspend time.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240218194912.6632e6dc7b35.Ie6e6a7488c9c7d4529f13d48f752b5439d8ac3c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 might (due to an unavoidable race) cancel a ROC that has already
expired. In that case the driver should not send the session protection
cmd to cancel the ROC.
When session protection is supported, the te_data::id field is reused
to save the configuration id. Check it before sending the cmd.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.30176bf869d9.Id811c20d3746b870cbe0c946bbfe1c0ab0a290cb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is set when a P2P ROC ends, and uses as an indication inside
iwl_mvm_roc_done_wk that the resources used for this ROC (sta/link)
needs to be flushed/deactivated (respectively).
But we also have IWL_MVM_STATUS_ROC_RUNNING, which is set whenever
P2P ROC starts, and is not even used in iwl_mvm_roc_done_wk.
Use IWL_MVM_STATUS_ROC_RUNNING as an indicator, and remove the redundant
bit.
While at it, add a call to synchronize_net also for the
AUX ROC case, which is missing in the existing code.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.0494f75de311.Ic4aacacf7581a5c9046c4f1df87cbb67470853e7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a conflict already and some upcoming changes
also depend on changes in wireless for being conflict-
free, so pull wireless in to make all that easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There may be different hardware or configurations supported,
so check for our own EMLSR capability before allowing it to
be used, in addition to checking the AP's.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240208185302.036443611696.If33caabd7cf372834287863b40b2d6d1ef1ca3f7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With C99 bool we really also should use true/false, not the
upper-case variants, wherever they may actually be coming
from. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240208185302.5732dd306ee9.Ifc07c026ac3779429e3dc949e96c9437e89f7bf9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New additions to the P2P specification use action frames to
extend the P2P device discovery and service discovery. Thus,
configure the P2P Device link to accept all management frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240208185302.7ae41234de7b.Ie0b08d4b965409ef6df5505396927567fb899d52@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware will now start with 1500 byte A-MSDU size
rather than 3500 as before, and that seems to cause some
really hard to debug problems. Keep A-MSDU disabled if
the size is less than 2000 to disable this for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240208185302.3dcd0a1767d0.I450d35f3085b3b04a96dd1e1e7d8c27bda9ce8f5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
6 GHz STA supports different power types as LPI, SP, VLP.
and this information is provided by regulatory info.
Add support in driver to parse the power type capability in
regulatory info from FW and set it to the channel flags.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240208185302.9c6a4acabdb3.I501de5c0d86b9702bf61158a2e91c954a1da9a2a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MFP, do not disconnect if an unprotected deauth
or disassoc was received during D3.
For that, need to configure wowlan with MFP (IS_11W_ASSOC).
Now, in case of an unprotected deauth/disassoc, the wakeup
reason returned by the firmware will be:
IWL_WAKEUP_BY_11W_UNPROTECTED_DEAUTH_OR_DISASSOC
(and not IWL_WOWLAN_WAKEUP_BY_DISCONNECTION_ON_DEAUTH
which will cause a disconnection).
Also, report this reason to cfg80211.
In another patch, the driver will send an SA query.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.fde438a22e3f.I3c8497520aaa95a22febff727b0ad08146965d47@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is always a bit confusing, the code first does all the
reclaim (with its own debug messages), and _then_ prints it
got a BA notification from firmware. Turn that around.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.825245e0803f.Ic607c57f43eb7c7ff122ffee8f3994fd040d578f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flags argument to enable/disable beacon filtering functions
is unused and always zero, so just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.2c739c1034a5.I8619949ad4ebd31593d10ece371ebdc6c48db98f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware (later) actually uses the values even for keys
that are invalid as far as the host is concerned, later in
rekeying, and then only sets the low 48 bits since the PNs
are only 48 bits over the air. It does, however, compare the
full 64 bits later, obviously causing problems.
Remove the memset and use kzalloc instead to avoid any old
heap data leaking to the firmware. We already init all the
other fields in the struct anyway. This leaves the data set
to zero for any unused fields, so the firmware can look at
them safely even if they're not used right now.
Fixes: 79e561f0f0 ("iwlwifi: mvm: d3: implement RSC command version 5")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.462101146fef.I10f3855b99417af4247cff04af78dcbc6cb75c9c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware versions no longer needs this command. Don't send it if
the firmware advertises it does not need it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.527595995aa0.I0381bef1dc815945f2ec194fecc657e5c75bb2ec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware doesn't need the MFP flag for the GTK, it can even make the
firmware crash. in case the AP is configured with: group cipher TKIP and
MFPC. We would send the GTK with cipher = TKIP and MFP which is of course
not possible.
Fixes: 5c75a208c2 ("wifi: iwlwifi: mvm: support new key API")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.2f2c602ab3c6.If13b2e2fa532381d985c07df130bee1478046c89@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For non-QoS nullfunc packets we currently do the duplicate detection,
which seems a bit wrong. Fix the code to check for _any_ instead of
just _qos_ nullfunc.
Also remove setting the RX_FLAG_DUP_VALIDATED flag, we haven't done
anything here; in particular, we haven't checked for multicast in an
MLO scenario.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.4fea3bd2d4a6.Ib80764f4581d875cff08469016894f7c817c3828@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When retrieving the queue index ("SCD SSN") from the TX response,
it's currently masked with 0xFFF. However, now that we have queues
longer than 4k, that became wrong, so make the mask depend on the
hardware family.
This fixes an issue where if we get a single frame reclaim while
in the top half of an 8k long queue, we'd reclaim-wrap the queue
twice (once on this and then again on the next non-single reclaim)
which at least triggers the WARN_ON_ONCE() in iwl_txq_reclaim(),
but could have other negative side effects (such as unmapping a
frame that wasn't transmitted yet, and then taking an IOMMU fault)
as well.
Fixes: 7b3e42ea2e ("iwlwifi: support multiple tfd queue max sizes for different devices")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.4148a6ef54e0.I733a70f679c25f9f99097a8dcb3a1f8165da6997@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After waking from D3, we set the iPN given by the firmware.
For some reason, CIPHER_SUITE_AES_CMAC was missed.
That caused copying garbage to the iPN - causing false replays.
(since 'seq' is on the stack, and the iPN from the firmware
was not copied into it, it contains garbage which later is
copied to the iPN key).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.2be5b35be30f.I99db8700d01092d22a6d76f1fc1bd5916c9df784@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If during D3 there was both a GTK rekey and a
disconnection, when waking up, we must first
update the new keys and then disconnect.
The reason is that when disconnecting we first need
to remove the keys.
Trying to remove invalid keys results in firmware
assert.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.68cf3974b5d7.Iac9b71a1906ab973aba9baadc9e923b63c0b4945@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With unlimited pseudo-D3, we can get stuck here in the read if
the firmware never wakes up. All of our testing infrastructure
however will anyway give up after at most a minute, so there's
no value in that.
Limit this to about a minute to avoid getting stuck with the
RTNL held forever, which basically makes the machine unusable
and then we can't even understand what caused the failure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.ca55b3a7fa8d.Id746846f187442ebc689416d2688f2bd9278c0e9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When waking from D3 (and a GTK rekey happened during
D3), the key itself is saved in iwl_wowlan_status_data::gtk
array, but the PN is saved in iwl_wowlan_status_data::gtk_seq
array.
The indices (of the same key) might differ in both arrays.
Fix using the gtk array index in the gtk_seq array.
Rather, iterate and search for the correct key in the
gtk_seq array.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.bdd0511c007d.I3325288c64c010a4d008ac4429de1c2b14ef764c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The client needs to disconnect from AP in case of more than 19 missed
beacons only if no data is coming from that AP, otherwise it needs to
stay connected.
Signed-off-by: Daniel Amosi <amosi.daniel@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.080195242c18.Ib166fc4e46666165a88e673a4a196cb8f18fdec4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before sending SESSION PROTECTION cmd the driver verifies that the
link for which the cmd is going to be sent is active.
The existing code is checking it only for MLD vifs,
but also the deflink (in non-MLD vifs) needs to be active in order
the have a session protection for it.
Fix this by checking if the link is active also for non-MLD vifs
Fixes: 1350658373 ("wifi: iwlwifi: support link_id in SESSION_PROTECTION cmd")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240205211151.c61820f14ca6.Ibbe0f848f3e71f64313d21642650b6e4bfbe4b39@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The BIOS tables SGOM and UATS are read from UEFI, but require
additional tables (WGDS and DSM func 3, respectively) which used to be
read from ACPI only, so the code handling those tables had to be under
ifdef ACPI. But now the driver reads those tables (WGDS and DSM) from
both ACPI and UEFI, so SGOM and UATS code shouldn't be under ifdef ACPI
anymore.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.dcaa3325773f.I649079c842369dcae3a362842322deca422a61d5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CT kill should stop doing a lot of TX etc. to cool down the
NIC, but we don't stop all commands from going to the NIC,
and as such we shouldn't abort queue sync, since it can get
confused if we do, warning that we do it twice at the same
time etc. Only stop it when we'd also not send it in the
first place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.4e0745e2cd97.I311dc623ce68de6a2da3c21c8d84a387844f714a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
define the timeout on RX queues notification as a macro so it will be
clearer.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.a6985ea87751.Iafb7ae13aa58d66512e4b3fa6c75149c75cbc305@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's a bit tricky to understand what's going on here, add
more data to the warning messages to make that clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.1df82a509636.I2f71811569a5c48eb166c4caa779af2d6160ad33@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise support for protected ranging negotiation if the firmware
supports it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206135637.9bb7e13ad18c.I578af1c9836e91069ce318b265bd221f42955992@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As documented in the comment, this queue sync was here to
ensure that an async IWL_MVM_RXQ_NSSN_SYNC queue sync won't
race with setting up a new BA session with the same BAID.
However, we no longer do IWL_MVM_RXQ_NSSN_SYNC queue sync,
so we can remove this as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Grumbach, Emmanuel <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240204235836.0a09ab337b54.I0dfe239dc30577a2ff23f910b10e9957364ccc78@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code here is the pre-MLD API, but of course older FW
that doesn't support MLD APIs cannot support EHT. Remove
some code that shouldn't be there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240204235836.bde5a9d87759.I4c69dd94416f92b0f1f53dd57dafecbec643600d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This debugfs entry is used to configure the rx_phyinfo.
Currently we are sending the phy cmd only for the deflink.
Change it to send the cmd for all active links of the vif
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240204235836.a68ee2b6cb58.Iddc47c608ec990b12be0ae5b1ee89bcf6beb0f6a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In much of the PHY context handling code the chandef
coming from mac80211 is read-only, mark them const
to make that clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240204235836.e7fbd3e26d85.I72d72e61dc5f5fc76c53e32cb60b66237eaedec3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently ieee80211_csa_finish() function finalizes CSA by scheduling a
finalizing worker using the deflink. With MLO, there is a need to do it
on a given link basis.
Pass link ID of the link on which CSA needs to be finalized.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, function to update beacon counter uses deflink to fetch
the beacon and then update the counter. However, with MLO, there is
a need to update the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data during beacon update counter.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-3-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Aloka originally suggested that puncturing should be part of
the chandef, so that it's treated correctly. At the time, I
disagreed and it ended up not part of the chandef, but I've
now realized that this was wrong. Even for clients, the RX,
and perhaps more importantly, CCA configuration needs to take
puncturing into account.
Move puncturing into the chandef, and adjust all the code
accordingly. Also add a few tests for puncturing in chandef
compatibility checking.
Link: https://lore.kernel.org/linux-wireless/20220214223051.3610-1-quic_alokad@quicinc.com/
Suggested-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://msgid.link/20240129194108.307183a5d2e5.I4d7fe2f126b2366c1312010e2900dfb2abffa0f6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A DoS tool that injects loads of authentication frames made our AP
crash. The iwl_mvm_is_dup() function couldn't find the per-queue
dup_data which was not allocated.
The root cause for that is that we ran out of stations in the firmware
and we didn't really add the station to the firmware, yet we didn't
return an error to mac80211.
Mac80211 was thinking that we have the station and because of that,
sta_info::uploaded was set to 1. This allowed
ieee80211_find_sta_by_ifaddr() to return a valid station object, but
that ieee80211_sta didn't have any iwl_mvm_sta object initialized and
that caused the crash mentioned earlier when we got Rx on that station.
Cc: stable@vger.kernel.org
Fixes: 57974a55d9 ("wifi: iwlwifi: mvm: refactor iwl_mvm_mac_sta_state_common()")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.1f76c44b2486.I6a00955e2842f15f0a089db2f834adb9d10fbe35@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code walking trip points in iwl_mvm_send_temp_report_ths_cmd()
reads the trip table passed to thermal_zone_device_register_with_trips()
in order to get the current trip temperatures, but this is not
guaranteed to work in the future, because the thermal zone will store
trip points information internally.
For this reason, make iwl_mvm_send_temp_report_ths_cmd() use
for_each_thermal_trip() as appropriate for walking trip points in a
given thermal zone.
No intentional functional impact, but it is requisite for future thermal
core improvements.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Miri Korenblit <Miriam.rachel.korenblit@intel.com>
The trip table in iwl_mvm_thermal_zone_register() is populated after
passing it to thermal_zone_device_register_with_trips(), so it may be
accessed (for instance, via sysfs) before it is ready.
To prevent that from happening, modify the function to populate the
trip table before calling thermal_zone_device_register_with_trips().
Also make the code use THERMAL_TEMP_INVALID as the "invalid temperature"
value which is also meaningful for the core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Miri Korenblit <Miriam.rachel.korenblit@intel.com>
The fw_trips_index[] array in struct iwl_mvm_thermal_device is only
populated, but never read, so drop it.
Note that the iwl_mvm_send_temp_report_ths_cmd() code populating
fw_trips_index[] is questionable, because it accesses a trips table
of a thermal zone directly, which is not guaranteed to work in the
future.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Miri Korenblit <Miriam.rachel.korenblit@intel.com>
Before sending a SESSION PROTECTION cmd the driver checks if
the link_id indicated in the time event (and for which the cmd will be
sent) is valid and exists.
Clear the te_data::link_id when FW notifies that a session protection
ended, so the check will actually fail when it should.
Fixes: 1350658373 ("wifi: iwlwifi: support link_id in SESSION_PROTECTION cmd")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240204235836.c64a6b3606c2.I35cdc08e8a3be282563163690f8ca3edb51a3854@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As described in IEEE sta 802.11-2020, table 9-30 (Address
field contents), A-MSDU address 3 should contain the BSSID
address.
In TX_CMD we copy the MAC header from skb, and skb address 3
holds the destination address, but it may not be identical to
the BSSID.
Using the wrong destination address appears to work with (most)
receivers without MLO, but in MLO some devices are checking for
it carefully, perhaps as a consequence of link to MLD address
translation.
Replace address 3 in the TX_CMD MAC header with the correct
address while retaining the skb address 3 unchanged.
This ensures that skb address 3 will be utilized later for
constructing the A-MSDU subframes.
Note that we fill in the MLD address, but the firmware will do the
necessary translation to link address after encryption.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240204235836.4583a1bf9188.I3f8e7892bdf8f86b4daa28453771a8c9817b2416@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For channel contexts, mac80211 currently uses the cfg80211
chandef struct (control channel, center freq(s), width) to
define towards drivers and internally how these behave. In
fact, there are _two_ such structs used, where the min_def
can reduce bandwidth according to the stations connected.
Unfortunately, with EHT this is longer be sufficient, at
least not for all hardware. EHT requires that non-AP STAs
that are connected to an AP with a lower bandwidth than it
(the AP) advertises (e.g. 160 MHz STA connected to 320 MHz
AP) still be able to receive downlink OFDMA and respond to
trigger frames for uplink OFDMA that specify the position
and bandwidth for the non-AP STA relative to the channel
the AP is using. Therefore, they need to be aware of this,
and at least for some hardware (e.g. Intel) this awareness
is in the hardware. As a result, use of the "same" channel
may need to be split over two channel contexts where they
differ by the AP being used.
As a first step, introduce a concept of a channel request
('chanreq') for each interface, to control the context it
requests. This step does nothing but reorganise the code,
so that later the AP's chandef can be added to the request
in order to handle the EHT case described above.
Link: https://msgid.link/20240129194108.2e88e48bd2e9.I4256183debe975c5ed71621611206fdbb69ba330@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some changes coming to wireless-next that will
otherwise cause conflicts, pull wireless in first to be
able to resolve that when applying the individual changes
rather than having to do merge resolution later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
dmi_get_system_info() will statically return NULL when the
kernel is compiled without CONFIG_DMI, leading to compiler
warnings. Fix that by printing "<unknown>" in that case.
Fixes: c3f40c3e02 ("iwlwifi: mvm: add US/CA to TAS block list if OEM isn't allowed")
Fixes: 9457077df4 ("wifi: iwlwifi: mvm: Add debugfs to get TAS status")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the following patch, iwl_mvm_roc_duration_and_delay and
iwl_mvm_roc_add_cmd will be called also from time-event.c.
Move then there (where they more belong) and make then
public.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240201155157.3edafc4d59aa.Ic68e90758bcad9ae00e0aa602101842dac60e1a1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AX210 and above have this logic offloaded in the firmware and it just
ignores the command coming from the driver.
Stop sending it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240201155157.4e3e0b52f98b.I7e9481050921d95c38f5a21ccc47112b3698e859@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For each DSM function, try to first read it from the UEFI.
If the UEFI WIFI GUID is unclocked, or the DSM function in
UEFI is invalid/unavailable - read it from ACPI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.27dd626ce2bd.Ib90bab74a9d56deb2362edb712294360e4ddae5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move all the common items (functions, enumerations and mcaros)
to regulatory.h/c files, and rename it to a common name.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.eae9bcbc0023.If1175f3143d6369076669ddd5d6ad4df0ee00659@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As DSMs are going to be read from UEFI too, we need a unified API
to get DSMs for both ACPI and UEFI.
The difference in getting DSM in each one of these methods (ACPI, UEFI)
is in the GUID, revision (0 for ACPI, 4 for UEFI), and size of the DSM
values (8 or 32 for ACPI, 32 for UEFI).
Therefore, change the iwl_acpi_get_dsm_x() to iwl_acpi_get_dsm() which
determines the GUID, revision (these two are the same for all WiFi DSMs),
and size (based on a func-to-size mapping) internally.
While at it, fix DSM_FUNC_RFI_CONFIG to expect a 32-bit value
(as defined in Intel BIOS spec) and not a 8-bit one.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.1bcd7072a7a5.I344ee0a11abbc27da0c693187d1b8bee653aaeef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These functions shouldn't be ACPI_CONFIG dependent, as they don't
access the ACPI. The functions that really access ACPI -
already handle the case that CONFIG_ACPI is not set.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.1412e6d561f8.I84f67478d01b576457e1bf489fbcb044adfda6fe@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Try to read the ECKV table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI.
Change iwl_acpi_get_eckv() to receive fwrt as argument so
it will be the same as all iwl_acpi_get_x() functions,
so it could be generated by the macro.
While at it - move the reading of ECKV to INIT stage. There is no
reason to read it each time we load the FW.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.d4937cc00727.I36e5fc7f7850229b9b377c80b5203aa47137c97c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Try to read the WRDD table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI.
Change iwl_acpi_get_mcc() to receive fwrt as argument so
it will be the same as all iwl_acpi_get_x() functions,
so it could be generated by the macro.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.5d52eeb109f7.I4d81700a7ae7fe2dfee14e363de358be59de7823@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set fast balance scan in case of active P2P GO, regardless of the
BSS DTIM interval.
This will increase the chances of scheduler to successfully schedule
out-of-channel events.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240201155157.310a00388e11.Ib136140dffa8704e68ff14e8fb69d35b97057171@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New tx devices may have issues sending NDPs from the host.
Send a CQM event instead. If the AP is really gone, we will get a beacon
loss and disconnect.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Berg, Johannes <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240201155157.e95d53448e94.I0ec92f1ca56a62cd8c13390b9fe60e9a7e9411c7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Try to read the SPLC table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.3d9d835b6edb.I7ea262df9431ced787b77c87149c6d7bddb7e7d6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the iwl_bios_get_x() functions are now generated using a macro,
and this macro requires the all iwl_acpi_get_x() to have the same
prototype, change iwl_acpi_get_pwr_limit() to return a int
and the actuall power limit will be filled in a pointer function
parameter.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.4cce81198afe.Ice8b1b97a68da9ec7b5a4799ddb668642198e1af@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the driver exits eSR by calling
iwl_mvm_esr_mode_inactive() before updating the FW
(by deactivating one of the links), and therefore before
sending the EML frame notifying that we are no longer in eSR.
This is wrong for several reasons:
1. The driver sends SMPS activation frames when we are still in eSR
and SMPS should be disabled when in eSR
2. The driver restores RLC configuration as it was before eSR
entering, and RLC command shouldn't be sent in eSR
Fix this by calling iwl_mvm_esr_mode_inactive() after FW update
Fixes: 12bacfc2c0 ("wifi: iwlwifi: handle eSR transitions")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.d8d9dc277d4e.Ib5aee0fd05e35b1da7f18753eb3c8fa0a3f872f3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Try to read the WTAS table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.45e6ff7b5063.Id3aec70887e14533b10d564f32c0cf5f2a14b792@changeid
[move uefi_tables_lock_status outside ifdef to fix build errors]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the TAS 'read-from-BIOS' flow receives the command struct
and the version of it as read from FW TLVs, and fills the command
accordingly.
This seems wrong, we should have the 'read-from-BIOS' flow
(iwl_acpi_get_tas in iwlwifi) reading/parsing/validating the table from
BIOS, and the 'send-to-FW' flow (iwl_mvm_tas_init) doing
all the FW versioning checks and cmd filling.
Move the cmd filling to the 'send-to-fw' flow.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.24df27772a71.I57b702af4feb3f38dc21d52593c25de4b1999e4b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We are going to support reading BIOS tables from UEFI
too, Refactor the TAS table flow:
1. Rename and move the common code to the regulatory.h/c files.
2. Remove the IWL_TAS_BLOCK_LIST_MAX, as we can use IWL_WTAS_BLACK_LIST_MAX
instead.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.0c2197cf1feb.Ib0e83d5bd3f4d5cfa9c3d2925317ba49377d257f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Try to read the PPAG table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.6516da09aec1.I0dcaf0b6d8857417ba1318467a28da5d0d7d7f27@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As PPAG table is going to be read from UEFI, there are some
cleanups required:
Move functions/definitions that are common to both UEFI and ACPI to
regulatory.h/c.
In addition, rename the functions/macros names so it will be clear which
one is ACPI specific, and which is common for ACPI and UEFI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.25623670b422.I8132af7517e4faf0ea8cbeb2efe9651edd319b98@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1. The name of iwl_read_ppag_table is misleading, as this function only
fills the command structure from the previously read table. Rename it.
2. Don't initialize fwrt::ppag_flags to 0 as the entire fwrt is zeroed
in the INIT stage anyway.
3. Don't filter out the reserved bits from fwrt::ppag_flags when printing
it, as it is already done in 'read-from-bios' flow.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.48acf340e817.I810e457b80015c1931d96d3e13c849f0339723c3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All the regulatory tables will be read from UEFI, and
only if it doesn't exist - they will be read from ACPI.
Read SAR tables (WRDS, EWRD and WGDS) from UEFI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.533b687e1efb.Icb316291e593c8d53f41fdea2d083367dc97e3c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_geo_tx_power_profiles_cmd::table_revision indicates whether
to use South Korea scheme or not.
We use South Korea scheme if the revision of WGDS table is 1.
We used to read the WGDS table from ACPI inside iwl_sar_geo_fill_table(),
so we had to set table_revision only after the call to it.
This added an extra if...else for each cmd version.
But it has been a while since we moved the BIOS tables reading to
INIT stage, and iwl_sar_geo_fill_table() is now only copying the
previously stored table to the cmd structure.
Set the table_revision before the call to iwl_sar_geo_fill_table()
and avoid that extra if...else.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.17a2384d4535.I306570874f1da0c6345066ebbf74a04b6c8aeb37@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver will support reading BIOS tables from UEFI
too. Refactor the SAR tables (WRDS, EWRD, WGDS) flows:
1. Move all the SAR logic/definitions that is common to both
UEFI and ACPI to a new file - regulatory.h/c.
2. Rename the relevant functions/definitions
so it will be clear which is ACPI specific and which is
for both ACPI and UEFI
3. Rename the function that copies the stored tables into the different
commands structures, so will be clear what these functions do.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.429a9baff34a.I040460348aa1b43609be3a317b86722d6be71c28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before using EMLSR check the AP actually advertises
support for it, otherwise reject the link activation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240131091413.edaac352488d.Ic3533afc6848591e8977391ae39c144d5e794d26@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using MLO, we need to have only a single link active
when entering suspend and of course most of the code also
needs to be adjusted to not use deflink, apart from older
code that's not used with MLO-capable firmware. Implement
that.
Note that the link selection currently prefers the "best"
link, which might really not be the best for D3, but that
can be fixed later once we agree.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240131091413.38f0fd4d2db0.I27c7a1d08aecc5da0af2c351212f22e92ed70219@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the check for using a chanctx's def vs. min_def,
to have the same in both places and reuse it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129211905.6fcde4051adf.I343934874612d21727ed167accaa967958b2c25b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we drop frames due to MIC error we want to have something
printed in the logger (this won't be printed by default).
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129211905.41b0abbf1fd2.Ib6ec6a48ec7bebe769d1e1c1df96380a758a0975@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the firmware has the necessary support, enable SPP A-MSDUs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129211905.15e4570e471f.I87cf284d3b19bb9f5558f0f33afaace6d6492acb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ADD_STA resets the link quality data inside the firmware. This is not
supposed to happen and has been fixed for newer devices. For older
devices (AX201 and down), this makes us send frames with rates that are
not in the TLC table.
Fixes: 5a86dcb4a9 ("wifi: iwlwifi: mvm: update station's MFP flag after association")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129211905.1deca7eaff14.I597abd7aab36fdab4aa8311a48c98a3d5bd433ba@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With MLO connections we need to let the firmware pick the rate
as we don't know the link the frame might be transmitted on
(in some cases we do know, but we'd rather always use the FW
and find bugs.) We _did_ end up finding bugs and fixing them,
but older devices likely won't get fixed as we don't have a
need for this there, they cannot support MLO.
Thus, go back to picking a rate on the host for the relevant
frames on older (pre-Bz) devices.
Fixes: 499d027904 ("wifi: iwlwifi: Use FW rate for non-data frames")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129211905.e59056d0a8cc.Iccc4c5c1753921d3d85241ede812a150fb05b898@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When secure LTF is used MFP must also be set.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129211905.6cad71069e87.I7f9fd5239cfd2244f155f88419980e6e91d00ff2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a spelling mistake in a WARN message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129211905.ff31e9385d29.I3a224e6a9294fdec431919fb4ec9315801e77454@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IPN is reported by the firmware in 6 bytes little endian,
but mac80211 expects big endian so it can do memcmp() on it.
We used to store this as a u64 which was filled in the right
way, but never used. When implementing that it's used, we
changed it to just be 6 bytes, but lost the conversion. Add
it back.
Fixes: 04f78e242f ("wifi: iwlwifi: mvm: Add support for IGTK in D3 resume flow")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129211905.138ed8a698e3.I1b66c386e45b5392696424ec636474bff86fd5ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for handling TID to link mapping negotiation
request and decide whether to accept it or not.
Accept the request if all TIDs are mapped to the same link set,
otherwise reject it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129211905.aab9819c378d.Icf6b79a362763e2e8b85959471f303b586617242@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All the regulatory tables from BIOS are going to be loaded
(preferably) from the UEFI instead of the ACPI.
There is a security issue with the fact that anyone can
add these UEFI variables.
The solution for that is to have a lock for all WIFI GUID UEFI
variables, and only if the UEFI variables are locked then we can
read it.
The status of the lock (unlocked, locked, test mode) is indicated
in a ACPI table: Guid Lock ACPI Indicator.
Load this table so the driver knows whether to read from UEFI or
not
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240128084842.53994809fbdd.I1bd10aafc387bc04f375e386861ee2bcb82f0a61@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When connecting to an AP, we currently initialize the rate
control only after associating. Since we now use firmware
to assign rates to auth/assoc frames rather than using the
data in the station and the firmware doesn't know, they're
transmitted using low mandatory rates. However, if the AP
advertised only higher supported rates we want to use them
to be nicer (it still must receive mandatory rates though),
so send the information to the firmware earlier to have it
know about it and be able to use it.
Fixes: 499d027904 ("wifi: iwlwifi: Use FW rate for non-data frames")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240128084842.ed7ab1c859c2.I4b4d4fc3905c8d8470fc0fee4648f25c950c9bb7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow to reconnect immediately instead of leaving the
connection in a limbo state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240128084842.e90531cd3a36.Iebdc9483983c0d8497f9dcf9d79ec37332a5fdcc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there was a rekey failure during D3 when firmware is
handling the GTK rekeying, and it decided that we should
wake up, then there was an issue in the connection and
we don't necessarily have the right keys, so we should
disconnect.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240128084842.944af193d479.I5ef9f1f0e048d44d7158615d071b793d69eceb75@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Andrei reports that we just silently drop beacons after we
report the key counters, but never report to userspace, so
wpa_supplicant cannot send the WNM action frame. Fix that.
Fixes: b1fdc2505a ("iwlwifi: mvm: advertise BIGTK client support if available")
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240128084842.7d855442cdce.Iba90b26f893dc8c49bfb8be65373cd0a138af12c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When removing a PASN station, the TK must be removed before
the station is removed as otherwise the FW would assert.
To handle this, store the key configuration, and use it to remove
the key when the station is removed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240131230734.3e6364730c04.Ia76dc4a9d399f1f68ac6b157d844b63f74d5159f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
eSR should be disabled when BT Coex is active and:
- LB link is the primary link.
- LB link is the secondary link and the predicted BT penalty
(the wifi loss rate caused by BT interference) is higher
than a given threshold.
If one of the conditions above is no longer true then re-enable eSR.
In order to implement this, add support for version 5 of
BT_PROFILE_NOTIFICATION, in which the bt penalty is provided
by FW.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131225342.b922b6485af8.I7d808ce535a7372aca9cb85c045755e6788a4904@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function to add an interface may be called without a previous
removal if the HW is being reconfigured. As such, only add the symlink
if the hardware is not being reconfigured due to a HW_RESTART.
Fixes: c36235acb3 ("wifi: iwlwifi: mvm: rework debugfs handling")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.314395eacda4.I5823e962c3c3674b942383733debd10b3fe903e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wiphy_work infra ensures that the entire worker will run
with the wiphy mutex. It is useful to have RX handlers
running as a wiphy_work, when we don't want the handler to
run in parallel with mac80211 work (to avoid races).
For example - BT notification can disable eSR starting from the next
patch.
In ieee80211_set_active_links we first check that eSR is
allowed, (drv_can_activate_links) and then activate it.
If the BT notif was received after drv_can_activate_links
(which returned true), and before the activation - eSR will be
activated when it shouldn't.
If BT notif is handled with the wiphy mutex, it can't run in
parallel to ieee80211_set_active_links, which also holds that
mutex.
Add the necessary infrastructure here, for use in the next commit.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240123200528.ce83d16cdec8.I35ef53fa23f58b9ec17924099238b61deafcecd7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This callback checks if a given bitmap of active_links
will be supported by the driver or not.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240123200528.a26fd48bfe3d.I03ae6b4c7fd24e8701660a68cec9403dc3469a0e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This command version adds two news fields:
sbb_bandwidth and sbb_ctrl_channel_loc
They will be populated later.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.82ab4140fff9.Icfba4819fe0b7ac8219ab671c632e25f5fbbaf6f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link ID in time event data is -1 when the time event is cleared.
Change the type of the link ID in the time event data structure
and in the affected function from unsigned to signed.
Fixes: 1350658373 ("wifi: iwlwifi: support link_id in SESSION_PROTECTION cmd")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240123200528.50d4941f946c.Iea990b118c69bc3e1eb61c1d134c9d470b3a17ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's either the pldr_sync case, in which case we didn't want
or do the retry loops anyway, or things will just continue to
fail. Remove the retry loop that was added in a previous attempt
to address the issue that was later (though still a bit broken)
addressed by the pldr_sync case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.f80a88a18799.I48f21eda090f4cc675f40e99eef69a986d21b500@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the STEP (the interface between MAC and PHY) is in URM
(a lower speed mode) then we cannot use 320 MHz MCS > 9.
Therefore, limit the MCS in our capabilities in this case.
Note that this also limits the TX/rate scaling since that
takes both TX and RX capabilities into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.02bae683b7fc.Id5efbb71d45da02c8c4e211d20396637ddd44da8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ENOTSUPP isn't a standard error code, don't use it. Replace with
EOPNOTSUPP instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.a69f4347b5f8.I88429d5de8251287ec0b58ff26a588465b9049a5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now, this isn't allowed. The API to mac80211 isn't great
for this, but we need to change the API to move puncturing
into the chanctx/chandef, and will do it better then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.38955b68b429.I0c4ae99179b271648a747a51eb04853504c7952c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't want to duplicate the definitions later,
so add them to the API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.6595e905997b.I12354d31676911b29ab30c81a4e9b87f59284d3b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
eSR is activated when a chanctx is assigned to more than one link.
During eSR activation we should disable RLC for both phys, and configure
the FW with a special phy command for both phys.
Currently we assign the phy_ctxt to the link only after eSR activation,
so RLC is not disabled for the new phy_ctxt, and a cmd is not sent to FW.
Fix this by first assigning the new phy_ctxt to the link and then
doing the eSR activation.
Fixes: 12bacfc2c0 ("wifi: iwlwifi: handle eSR transitions")
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.3d94507f5d9a.I537fcd73aedf94c7348c03157e486f24301fef14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver copies the userspace buffer into an internal NUL
byte terminated buffer. While doing so, it was reading beyond
the end of the userspace buffer, overwriting its own NUL
termination in the process.
Fix this by only copying the correct number of bytes.
Fixes: 3f244876ef ("wifi: iwlwifi: make debugfs entries link specific")
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.e4913deb2ad4.Idcf6a7e909ff4b7801cd49c2f691f84a2f68eff9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that though multiple links are enabled we cannot enabled
EMLSR enable more than a single link, e.g., all valid links are on the
same band etc. Thus, do not warn in case no valid link pair is found.
Fixes: b9be67fb42 ("wifi: iwlwifi: mvm: Add basic link selection logic")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.142e57a05230.I7cfe78c94c3d15c4c744bccadd8f187e43594932@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now with the mac80211 locking model changed, we no longer can
cause any bad dependencies here between mvm->mutex and other
mutexes in mac80211, so we no longer need to drop the mutex
early or even temporarily. Clean this up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.1f2f5289ecc6.I7e3b8e806b6d50e88ba0c26767da8261806eb9c7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we want to drop packets, that's surely a good thing to
do when we want to enter rfkill. Send this command despite
rfkill so we can successfully clean up everything, we need
to handle it separately since it has CMD_WANT_SKB, so it's
not going to automatically return success when in rfkill.
Fixes: d4e3a341b8 ("iwlwifi: mvm: add support for new flush queue response")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.c528a6fa6cec.Ibe5e9560359ccc0fba60c35e01de285c376748a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware changed their mind, don't set the chains to zero,
instead set them to 1 as we normally would for connections to
APs that don't use MIMO.
Fixes: 2a7ce54ccc ("iwlwifi: mvm: honour firmware SMPS requests")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.7f031f1a127f.Idc816e0f604b07d22a9d5352bc23c445512fad14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The second features pull request for v6.8. A bigger one this time with
changes both to stack and drivers. We have a new Wifi band RFI (WBRF)
mitigation feature for which we pulled an immutable branch shared with
other subsystems. And, as always, other new features and bug fixes all
over.
Major changes:
cfg80211/mac80211
* AMD ACPI based Wifi band RFI (WBRF) mitigation feature
* Basic Service Set (BSS) usage reporting
* TID to link mapping support
* mac80211 hardware flag to disallow puncturing
iwlwifi
* new debugfs file fw_dbg_clear
mt76
* NVMEM EEPROM improvements
* mt7996 Extremely High Throughpu (EHT) improvements
* mt7996 Wireless Ethernet Dispatcher (WED) support
* mt7996 36-bit DMA support
ath12k
* support one MSI vector
* WCN7850: support AP mode
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmWAdRERHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZu0RAf+JtHgfjmUMFb54xcncLgj8ZAN82E0ThE0
bPewQDhot0QTri4s7i5Kn8PCWjk+eKEmiIK+eARM+JDyZMTlCpXs2Y92cDAGQ8KG
+LbIMRQkwOUg0HmtX3NysUG3mGAx4QTcIX/y3+GmtMZpKXMFuNy6ODuFvuWFNJrF
3XTq1qFQNnA0XqUDKHW9uareeCiOMVOsqcxNW2FAi2gqRUfQpKnU1Ukv5iOjkqE9
i53GHzeAG2WI4/YjXaTEZvibkM3jqrPcquHlul3fVuq05qkKOEuiy2UalDjgDCYp
u91vbmMpcOjhlf9GIiu2BF6K/muEUCCIjlh5oxob0k9NiKhnPUZLng==
=6Y8M
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The second features pull request for v6.8. A bigger one this time with
changes both to stack and drivers. We have a new Wifi band RFI (WBRF)
mitigation feature for which we pulled an immutable branch shared with
other subsystems. And, as always, other new features and bug fixes all
over.
Major changes:
cfg80211/mac80211
* AMD ACPI based Wifi band RFI (WBRF) mitigation feature
* Basic Service Set (BSS) usage reporting
* TID to link mapping support
* mac80211 hardware flag to disallow puncturing
iwlwifi
* new debugfs file fw_dbg_clear
mt76
* NVMEM EEPROM improvements
* mt7996 Extremely High Throughpu (EHT) improvements
* mt7996 Wireless Ethernet Dispatcher (WED) support
* mt7996 36-bit DMA support
ath12k
* support one MSI vector
* WCN7850: support AP mode
* tag 'wireless-next-2023-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (207 commits)
wifi: mt76: mt7996: Use DECLARE_FLEX_ARRAY() and fix -Warray-bounds warnings
wifi: ath11k: workaround too long expansion sparse warnings
Revert "wifi: ath12k: use ATH12K_PCI_IRQ_DP_OFFSET for DP IRQ"
wifi: rt2x00: remove useless code in rt2x00queue_create_tx_descriptor()
wifi: rtw89: only reset BB/RF for existing WiFi 6 chips while starting up
wifi: rtw89: add DBCC H2C to notify firmware the status
wifi: rtw89: mac: add suffix _ax to MAC functions
wifi: rtw89: mac: add flags to check if CMAC and DMAC are enabled
wifi: rtw89: 8922a: add power on/off functions
wifi: rtw89: add XTAL SI for WiFi 7 chips
wifi: rtw89: phy: print out RFK log with formatted string
wifi: rtw89: parse and print out RFK log from C2H events
wifi: rtw89: add C2H event handlers of RFK log and report
wifi: rtw89: load RFK log format string from firmware file
wifi: rtw89: fw: add version field to BB MCU firmware element
wifi: rtw89: fw: load TX power track tables from fw_element
wifi: mwifiex: configure BSSID consistently when starting AP
wifi: mwifiex: add extra delay for firmware ready
wifi: mac80211: sta_info.c: fix sentence grammar
wifi: mac80211: rx.c: fix sentence grammar
...
====================
Link: https://lore.kernel.org/r/20231218163900.C031DC433C9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Newest firmware has completely offloaded this logic and this command
will be deprecated soon. Based on a capability bit advertised by the
firmware, skip this command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231207044813.e64ef70c0133.I9f47cdef2ba45f1f383b70023857376973de3a8c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only one user of this code, which is STA unblock
during sleep for uAPSD on really old devices. Instead of
having this all through the API with calls up and down,
just implemented a special-case CMD_BLOCK_TXQS flag for
this, it's only needed in the old gen1 transport.
While at it, fix a complain that lockdep would have, as
we lock the cmd queue and then the TXQs in the reclaim
by using spin_lock_nested(). We no longer need to disable
BHs in iwl_trans_pcie_block_txq_ptrs() since it's called
with them disabled already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231207044813.2bd95e0570fc.I16486dbc82570d2f73a585872f5394698627310d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used by the user space when it wants to clear the data we
collected so far for privacy reasons.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231207044813.d5e97d5ec0d9.I7a5e836e6109e1fce7e6301dba8d1f28e60a5440@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For an MLO connection, the BSSID of the link used during the scanning
should be used (and not the one from the default link).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231207044813.1e67dba640c1.I6c4941bfab3a04498370e58b402c64d990c39fbf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- debugfs had a deadlock (removal vs. use of files),
fixes going through wireless ACKed by Greg
- support for HT STAs on 320 MHz channels, even if it's
not clear that should ever happen (that's 6 GHz), best
not to WARN()
- fix for the previous CQM fix that broke most cases
- various wiphy locking fixes
- various small driver fixes
-----BEGIN PGP SIGNATURE-----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=X6t2
-----END PGP SIGNATURE-----
Merge tag 'wireless-2023-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
wireless fixes:
- debugfs had a deadlock (removal vs. use of files),
fixes going through wireless ACKed by Greg
- support for HT STAs on 320 MHz channels, even if it's
not clear that should ever happen (that's 6 GHz), best
not to WARN()
- fix for the previous CQM fix that broke most cases
- various wiphy locking fixes
- various small driver fixes
* tag 'wireless-2023-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: use wiphy locked debugfs for sdata/link
wifi: mac80211: use wiphy locked debugfs helpers for agg_status
wifi: cfg80211: add locked debugfs wrappers
debugfs: add API to allow debugfs operations cancellation
debugfs: annotate debugfs handlers vs. removal with lockdep
debugfs: fix automount d_fsdata usage
wifi: mac80211: handle 320 MHz in ieee80211_ht_cap_ie_to_sta_ht_cap
wifi: avoid offset calculation on NULL pointer
wifi: cfg80211: hold wiphy mutex for send_interface
wifi: cfg80211: lock wiphy mutex for rfkill poll
wifi: cfg80211: fix CQM for non-range use
wifi: mac80211: do not pass AP_VLAN vif pointer to drivers during flush
wifi: iwlwifi: mvm: fix an error code in iwl_mvm_mld_add_sta()
wifi: mt76: mt7925: fix typo in mt7925_init_he_caps
wifi: mt76: mt7921: fix 6GHz disabled by the missing default CLC config
====================
Link: https://lore.kernel.org/r/20231129150809.31083-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since 'tz_device' is an in-place member of 'struct iwl_mvm', it can't
be NULL and so relevant check may be dropped. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231003092048.24998-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the vif is in MLD mode, we'll get a vif links change from
non-zero to zero on disassociation, which removes all links in
the firmware and adds the 'deflink' the driver/mac80211 has.
This causes the firmware to clear some internal state.
However, in non-MLD mode, this doesn't happen, and causes some
state to be left around in firmware, which can particularly
cause trouble with the ref-BSSID in multi-BSSID, leading to an
assert later if immediately making a new multi-BSSID connection
with a different ref-BSSID.
Fix this by removing/re-adding the link in the non-MLD case
when the channel is removed from the vif. This way, all of the
state will get cleared out, even if we need the deflink, which
is more for software architecture purposes than otherwise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231022173519.90c82837ba4d.I341fa30c480f7673b14b48a0e29a2241472c2e13@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a TX queue has no space for new TX frames, the driver will keep
these frames in the overflow queue, and during reclaim flow it
will retry to send the frames from that queue.
But if the reclaim flow was invoked from TX queue flush, we will also
TX these frames, which is wrong as we don't want to TX anything
after flush.
This might also cause assert 0x125F when removing the queue,
saying that the driver removes a non-empty queue
Fix this by TXing the overflow queue's frames only if we are
not in flush queue flow.
Fixes: a445098058 ("iwlwifi: move reclaim flows to the queue file")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231022173519.caf06c8709d9.Ibf664ccb3f952e836f8fa461ea58fc08e5c46e88@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Driver need to provide details of VLP, AFC
AP type supported for the specific MCC to firmware.
Driver will read the UATS (UHB AP type support) table
from BIOS and sent to firmware using UATS_TABLE_CMD.
Add the support for the same in the driver.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231022173519.eb6cf7be17b2.I8977a660564412056d9fd383d57b236cd4b22d00@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new firmware API uses a new command and notification,
the command configures in which statistics types driver is
interested and the notification is sent periodically.
An additional change in the API is that most of the statistics
data is accumulated and reported by the firmware per MLO link.
Implement new command and notification handlers and adjust to
per-link statistics.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231022173519.8cc7df0ebff2.If1dcb57145841c5b3c68ed112bbfcd0201f7acc3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to get regulatory domain, driver sends MCC_UPDATE_CMD to the
FW. One of the parameters in the response is the status which can tell
if the regdomain has changed or not.
When iwl_mvm_init_mcc() is called during iwl_op_mode_mvm_start(), then
sband is still NULL and channel parameters (i.e. chan->flags) cannot be
initialized. When, further in the flow, iwl_mvm_update_mcc() is called
during iwl_mvm_up(), it first checks if the regdomain has changed and
then skips the update if it remains the same. But, since channel
parameters weren't initialized yet, the update should be forced in this
codepath. Fix that by adding a corresponding parameter to
iwl_mvm_init_fw_regd().
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.78b2c5b891b0.Iac49d52e0bfc0317372015607c63ea9276bbb188@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During the D3 resume flow, all new rekeys are passed from the FW.
Because the FW supports only one IGTK at a time, every IGTK rekey
update should be done by removing the last IGTK. The mvmvif holds a
pointer to the last IGTK for that reason and thus should be updated
when a new IGTK is passed upon resume.
Fixes: 04f78e242f ("wifi: iwlwifi: mvm: Add support for IGTK in D3 resume flow")
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.8ceaf7e5ece7.Ief444f6a2703ed76648b4d414f12bb4130bab36e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware / hardware of devices supporting RSS is able to report
duplicates and packets that time out inside the reoder buffer. We can
now remove all the complex logic that was implemented to keep all the Rx
queues more the less synchronized: we used to send a message to all the
queues through the firmware to teach the different queues about what is
the current SSN every 2048 packets.
Now that we rely on the firmware / hardware to detect duplicates, we can
completely remove the code that did that in the driver and it has been
reported that this code was spuriously dropping legit packets.
Suggested-by: Sultan Alsawaf <sultan@kerneltoast.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.54cf4d3d5956.Ic06a08c9fb1e1ec315a4b49d632b78b8474dab79@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Multi rx queue allows to spread the load of the Rx streams on different
CPUs. 9000 series required complex synchronization mechanisms from the
driver side since the hardware / firmware is not able to provide
information about duplicate packets and timeouts inside the reordering
buffer.
Users have complained that for newer devices, all those synchronization
mechanisms have caused spurious packet drops. Those packet drops
disappeared if we simplify the code, but unfortunately, we can't have
RSS enabled on 9000 series without this complex code.
Remove support for RSS on 9000 so that we can make the code much simpler
for newer devices and fix the bugs for them.
The down side of this patch is a that all the Rx path will be routed to
a single CPU, but this has never been an issue, the modern CPUs are just
fast enough to cope with all the traffic.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.2917eb8b7af9.Iddd7dcf335387ba46fcbbb6067ef4ff9cd3755a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_remove_link would return an error if the link could not be
removed. However, doing so prevents recovery if a link was not uploaded
to the FW in the first place and the link_info was not allocated or
fw_link_id is not set.
Returning success means that we can still try to continue with adding
new links in change_vif_links.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.f89bc05aadf6.Idc8fbd671362d962c02b1df87fa6258733631580@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In new firmware, we don't need this any more and it won't
be called any more by mac80211, since powersave handling
is all done by firmware. Remove it from the MLD ops.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.1a1ded96ffc2.Ie49d3004acdd6299fb84346c76b2b2b2f195196b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As session protection API is moving to be per link instead of per mac,
move the time events to be per link too.
Since there is only one concurrent time event per mac, it feels
unnecessary to have the time_event as a member of iwl_mvm_link_info.
(That way we will have to iterate over all links each time we want to
clear a time event, and also we will need mac80211 to tell us the link
id when mgd_tx_complete() is called.)
So leave this as a member of iwl_mvm_vif, but add the link id to the
time_event structure.
The link id in time_event will only be maintained and used for:
1. When SESSION_PROTECTION_CMD is supported (before it, we don't have MLO)
2. For time_events of types SESSION_PROTECT_CONF_ASSOC,
SESSION_PROTECT_CONF_P2P_DEVICE_DISCOV, and
SESSION_PROTECT_CONF_P2P_GO_NEGOTIATION
(not for aux roc/ Hot Spot time_events).
For P2P, non-MLO connections, and pre-MLD API, deflink id, meaning 0,
will be used
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.21496bcacb18.I79d037325b4fae4c12a22d9477e53fc9c537ad46@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
make htmldocs warns:
Documentation/driver-api/80211/mac80211:109: ./include/net/mac80211.h:5170: WARNING: Duplicate C declaration, also defined at mac80211:1117.
Declaration is '.. c:function:: void ieee80211_tx_status (struct ieee80211_hw *hw, struct sk_buff *skb)'.
This is because there's a function named ieee80211_tx_status() and a struct named
ieee80211_tx_status. This has been discussed previously but no solution found:
https://lore.kernel.org/all/20220521114629.6ee9fc06@coco.lan/
There's also a bug open for three years with no solution in sight:
https://github.com/sphinx-doc/sphinx/pull/8313
So I guess we have no other solution than to a workaround this in the code,
for example to rename the function to ieee80211_tx_status_skb() to avoid the
name conflict. I got the idea for the name from ieee80211_tx_status_noskb() in
which the skb is not provided as an argument, instead with
ieee80211_tx_status_skb() the skb is provided.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231012114229.2931808-2-kvalo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a requirement from OEMs to support a new bit in DSM function 8,
which will indicate that this device is an indoor one, and that it
should activate UNII-1 (5.2GHz) sub band in the World Wide Geo Profile.
Add support for this by reading this bit from BIOS and sending it to the
FW.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.86d4ad178042.Ief40acc08b5482ff147fd17e74e36f1933e43def@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we remove TDLS stations, we need to remove them from FW
immediately, even while associated. Some previous refactoring
here lost the sta ID condition, add it back.
Fixes: 57974a55d9 ("wifi: iwlwifi: mvm: refactor iwl_mvm_mac_sta_state_common()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.933011e710a9.I77c069c781e8b2b698b86cc3f43fc3c7e2dde114@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When I implemented iwl_mvm_mac_flush_sta() I completely botched it;
it basically always happens after the iwl_mvm_sta_pre_rcu_remove()
call, and that already clears mvm->fw_id_to_mac_id[] entries, so we
cannot rely on those at iwl_mvm_mac_flush_sta() time. This means it
never did anything.
Fix this by just going through the station IDs and now with the new
API for iwl_mvm_flush_sta(), call those.
Fixes: a6cc6ccb1c ("wifi: iwlwifi: mvm: support new flush_sta method")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.0b5878e93118.I1093e60163052e7be64d2b01424097cd6a272979@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This API is type unsafe and needs an extra parameter to know
what kind of station was passed, so it has two, but really it
only needs two values. Just pass the values instead of doing
this type-unsafe dance, which will also make it better to use
for multi-link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.aeb3bf4204cd.I5b0e6d64a67455784bc8fbdaf9ceaf03699d9ce1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We seem to have an issue in case we had a BSS and a P2P device on
channel 1 and then, the P2P device gets an ROC on channel 6. We would
change the channel of the PHY context to channel 6 even if the BSS was
using that same PHY context.
Revamp that code and don't try to change a PHY context, it doesn't mean
much for the firmware anyway. Just remove it and allocate a new one.
This makes the logic easier to follow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.4bc8b90d7be0.I1232dca3fe007362ec0ae0cf1d96217f2544e0d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we want to add a phy_ctxt, we need to increase the ref.
Note that all the WARN_ONs are already in place:
* We check that we don't add a context with ref != 0
* We check that we don't modify a context with ref = 0
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.c19c07746b26.I5b0cbe0760811631a320218a10b88870b5bf0897@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
From its very first stages of development, iwlmvm added all the PHY
context immediately upon firmware boot. Then, all we needed to do is to
modify the contexts. This was fine if the addition of a PHY context that
we don't need is free. This was true until now. Newer devices will run
calibrations upon the addition of a PHY context.
Change the way we work with PHY context in iwlmvm. Fortunately, we
already have all the ref counting in place so that it is not very hard
to do.
Also, since we now remove the PHY context before the link is removed
(but after it has been de-activated of course), it'll confuse the
firmware if we put the late phy_id into the LINK command that removes
the link. Change this to put an invalid phy_id just like we do when we
add a link that has no PHY context yet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.55a1a78719be.I2032a7d227b57f4fc4370a2793476d47538404fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
bss_info_changed() callback of mac80211 was originally in both
MLD and non-MLD API. Therefore, we extracted the common part
to a function which receives a callback structure with the
mode-specific (non-MLO\MLO) ops. Eventually, for MLO API,
bss_info_changed() callback was split into 2 callbacks:
link_info_changed() and vif_cfg_changed() so it is no longer in use
for MLO, only for non-MLO.
Remove the code that uses the mode-specific callback structure.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.b65fbcdb9295.I2a64a6f1178ee0466755d728addc77acbb2ed6f4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Read the EDT (Energy detection threshold) optimization configuration
table from BIOS using DSM Function and send it to FW.
Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.0b78ee48219a.I8ecbd39d258e2ee0514a7e28632f6c18fb798a83@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an IGTK is installed for an AP interface, there is no station
associated with it. However, the MFP flag must be set for the installed
key as otherwise the FW wouldn't use it.
Fix the security key flag to set the MFP flag also when the AP is
an AP interface and the key index matches that of an IGTK.
Fixes: 5c75a208c2 ("wifi: iwlwifi: mvm: support new key API")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.f67005e2d4d2.I6832c6e87f3c79fff00689eb10a3a30810e1ee83@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In reality 64 bytes are enough to hold fw version string,
but some compilers can complain (with W=1) that output may be
truncated when building this string with snprintf.
Increase the size to avoid this sort of warnings and state
explicitely that we want the size to be trancated to 32 bytes.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Tested-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012153950.f4465b4b4e2b.Idced2e8d63c492872edcde1a3ce2cdd6cc0f8eb7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case the link puncturing is changed such that the channel
is no longer punctured, configure the FW correctly indicating
the EHT parameters changed (with a 0 punctured map).
Allow EHT parameters configuration only when the link really
supports EHT.
Fixes: 55eb1c5fa4 ("wifi: iwlwifi: mvm: add support for the new LINK command")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.2666ef86e032.I4b0e95722660acc5345ceefba7e8866a69572e8e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is not necessary to keep the P2P Device bound/linked to a PHY
context when there is no active ROC.
Modify the P2P Device flows so the binding/linking would be done
only while ROC is active. With this change the switch_phy_ctxt()
is no longer needed so remove it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.c5b83b4bf9de.Ia80daf3ba0b5fec7d0919247fcbdbdb58bddf02b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac_ctdp_sum contains the power consumption, appears in power save
report, and is used for debugging and collection of statistics.
Add a debugfs handler to start this calculation, iff ctdp
command is supported in the firmware.
While on it, add an option to force start/stop this calculation,
which is safe from the firmware API side.
Signed-off-by: iallouch <itai.allouche@intel.com>
Signed-off-by: Nitsan Bar <nitsan.bar@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.024d75df9e03.I69fdc826f2931a6e1435b450f0602ea060704697@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In RFKILL we first set the RFKILL bit, then we abort scan
(if one exists) by waiting for the notification from FW
and notifying mac80211. And then we stop the device.
But in case we have a scan ongoing in the period of time between
rfkill on and before the device is stopped - we will not wait for the
FW notification because of the iwl_mvm_is_radio_killed() condition,
and then the scan_status and uid_status are misconfigured,
(scan_status is cleared but uid_status not)
and when the notification suddenly arrives (before stopping the device)
we will get into the assert about scan_status and uid_status mismatch.
Fix this by waiting for FW notif when rfkill is on but the device isn't
disabled yet.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.c43b69aa2c77.Icc7b5efb47974d6f499156ff7510b786e177993b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add simple logic that would allow using EMLSR in case
there are multiple valid links:
- In case the connection establishment has just been
completed try to find a valid link pair for EMLSR
functionality where one of the links in the pair is
the current active link.
- In case the valid links changed after connection
was already established, try to find a valid link pair
for EMLSR functionality, in case the EMSLR is not active
yet.
If a valid link pair is found call mac80211 to asynchronously
set the new link pair, otherwise continue using the current active
links.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.0c7b89ab29c2.I6600bd16551d75e2bf520d8d0add525568a9f85f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We shouldn't check the 0x10 bit here, since the register
holds different values (not just bit masks.). Check for
the exact value where this is needed only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.ab21c7d5e219.I4f9906ebc7ecf38fd276510a276280a9261c8f7f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a per-link debugfs entry in iwlmvm level so we can read/write link
related parameters.
Do it by implementing the link_add_debugfs API introduced by mac80211.
Each entry will have a path like this:
.../netdev:wlan0/link-X/iwlmvm/<file_name>
for each link X.
For non-MLD vifs this callback is called when the original vif
debugfs dir is also created, so handle that case by not creating
the 'iwlmvm' directory again.
Note that we don't have to worry about the cleaning the iwlmvm/*
directory as it is already done by mac80211 when removing the link
(or netdev).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.6a161f021ae8.Ic8f40f2b4682270c94036e3c11c3996ae34266fa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 added a new callback to add a vif debugfs.
Implement it instead of adding the debugfs directly,
which will make it properly preserved over switching
the vif from non-MLD/MLD and back.
This requires some rework so that we still have the
symlink but trust mac80211 to add/remove the debugfs.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.818810e242e6.I805a28f9fbef5c52a3a575d04e7a6a909ecf9078@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since userspace can choose now what link to establish the
TDLS on, we should know on what channel to do session protection.
Add a link id parameter to this callback.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.ef12ce3eb835.If864f406cfd9e24f36a2b88fd13a37328633fcf9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
EMLSR operation and SMPS operation cannot coexist. Thus, when EMLSR is
enabled, all SMPS signaling towards the AP should be stopped (it is
expected that the AP will consider SMPS to be off).
Rename IEEE80211_VIF_DISABLE_SMPS_OVERRIDE to IEEE80211_VIF_EML_ACTIVE
and use the flag as an indication from the driver that EMLSR is enabled.
When EMLSR is enabled SMPS flows towards the AP MLD should be stopped.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.fb2c2f9a0645.If6df5357568abd623a081f0f33b07e63fb8bba99@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't (yet) send the IGTK down to the firmware, but when
we do it needs to be with the broadcast station ID, not the
multicast station ID. Same for the BIGTK, which we may send
already if firmware advertises it (but it doesn't yet.)
Fixes: a5de7de7e7 ("wifi: iwlwifi: mvm: enable TX beacon protection")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230926110319.dbc653913353.I82e90c86010f0b9588a180d9835fd11f666f5196@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can't really know easily if a BIGTK will be used, but
in case firmware supports BIGTK it also supports the very
easy IGTK use (nothing to do on the host), and requires
that we program both IGTK and BIGTK to be able to use the
BIGTK. Thus, change the condition here to set the keys in
firmware (both IGTK/BIGTK) if BIGTK is supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230926110319.425ebc1ce484.If485ec962636c23d463b678e7da86e11b6fa86c9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The management frames protection flag is always set when the station
is not yet authorized. However, it was not cleared after association
even if the association did not use MFP. As a result, all public
action frames are not parsed by fw (which will cause FTM to fail,
for example). Update the station MFP flag after the station is
authorized.
Fixes: 4c8d5c8d07 ("wifi: iwlwifi: mvm: tell firmware about per-STA MFP enablement")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230926110319.2488cbd01bde.Ic0f08b7d3efcbdce27ec897f84d740fec8d169ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Resolve several conflicts, mostly between changes/fixes in
wireless and the locking rework in wireless-next. One of
the conflicts actually shows a bug in wireless that we'll
want to fix separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
The support for using link ID in the scan request API was only
added in version 16. However, the code wrongly enabled this
API usage also for older versions. Fix it.
Reported-by: Antoine Beaupré <anarcat@debian.org>
Fixes: e98b23d0d7 ("wifi: iwlwifi: mvm: Add support for SCAN API version 16")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230926165546.086e635fbbe6.Ia660f35ca0b1079f2c2ea92fd8d14d8101a89d03@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull up the injection rate control one layer, and let it
control the antenna settings as well. Since mac80211 has
already checked that enough antennas are configured, and
we only have two bits, it's enough to just copy the data
over.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230921110727.12ab7634dbbc.I5aa16c99864ecd7375011a8996de2564fd01fc30@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the injection and other frame TX rate handling
to always return the injection rate directly, by factoring
the legay rate portion out into a new function called in
the two relevant places (injection and non-injection).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230921110727.dc920357bad0.I5ee8512fb63f0423c1da35b59fea8811d60c1ad3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This new version of wolan_info_notif supports the handling
of bigtk during d3, this patch holds parsing of the new
notif version, adding new keys and updating ipn of
existing keys during the resume flow.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230921110726.4ebcd244f436.Ib507573d50fa0ac666d09ab71f5241ccbcd7cd00@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During HW restart, STA link changes happen while the link-sta is
already allocated (had been prior to the restart). Adjust the
allocation and checks to handle that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230921110726.99b7cc754b00.Iaa0503a3100250489fed8b4bdcf60e24a96d3392@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During HW restart in eSR, links allocated in a station and links
active in the interface may differ. Use for_each_sta_active_link
to capture this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230921110726.7ee1f1a55e1c.I410c512d1fad7d1cf9b2d2a3451a312821dc816d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
set_antenna() is supported only when the device is not started in
mac80211 which translates to the firmware not being loaded in iwlwifi.
The tricky part is that iwlwifi populates the sband data during its boot
and doesn't touch this data afterwards, but if the antenna settings
forbid MIMO, we need to update the sband data.
Rework the nvm parsing code to allow to get an existing nvm_data and
modify the sband with additional constraints (tx / rx chains masks).
Suggested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230921110726.81d94d630c95.I9473da818cbeeb51b2f89dcc59b00019113e7f55@changeid
[add bugfix from Benjamin for iwl_mvm_get_valid_rx_ant()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Getting a BAR can be an explanation if we're chasing packet loss. Add a
print with the relevant debug level in that code path.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.913e989a1751.I6bff9020e339d91b61b5ad6aede27bcf8c7e6819@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Transition to d3 is much faster if there is no power save during the
transition. Therefore a new flag was added to the device power cmd to
indicate the power save isn't allowed until the transition is completed.
Set this flag in _iwl_mvm_suspend, when the transition begins.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.ced036106507.Ib5ed5a47ee35f624902bd8882dde3e559285965b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the firmware crashes in the de-activation / re-activation
of the link during CSA, we will not have a valid phy_ctxt
pointer in mvmvif. This is a legit case, but when mac80211
removes the station to cleanup our state during the
re-configuration, we need to make sure we clear ap_sta
otherwise we won't re-add the station after the firmware has
been restarted. Later on, we'd activate the link, try to send
a TLC command crash again on ASSERT 3508.
Fix this by properly cleaning up our state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.2651e6f6a55a.I4cd50e88ee5c23c1c8dd5b157a800e4b4c96f236@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently we are setting the rate in the tx cmd for
mgmt frames (e.g. during connection establishment).
This was problematic when sending mgmt frames in eSR mode,
as we don't know what link this frame will be sent on
(This is decided by the FW), so we don't know what is the
lowest rate.
Fix this by not setting the rate in tx cmd and rely
on FW to choose the right one.
Set rate only for injected frames with fixed rate,
or when no sta is given.
Also set for important frames (EAPOL etc.) the High Priority flag.
Fixes: 055b22e770 ("iwlwifi: mvm: Set Tx rate and flags when there is not station")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.6c7e59620ee0.I6eaed3ccdd6dd62b9e664facc484081fc5275843@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the channel bandwidth is greater or equal than 80MHz,
enable FILS DF transmittion, even if the control channel is non-PSC.
That's because that in 80MHz there must be a sub 20MHz PSC
channel, and since the FILS DF is duplicated on all sub 20MHz
channels, within the 80MHz (hence it will be sent on a PSC channel).
Also, if FILS DF Tx is enabled, always configure the firmware
with the actual channel bandwidth, even before there is a connected
client (rather than the minimum bandwidth e.g. 20MHz), since FILS
DF transmission on a PSC channel take presedent over power
consumption.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.83b9a76fc6c4.I6703111cc6befcd0e9cd9adf3cb127a648dbb7b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device initialized with ME active, this would indeed
work, since the NVM information would be obtained from ME.
However, in the much more likely case that ME isn't active
and the firmware takes actions requiring the sync, this was
not working correctly when the firmware is only run at init
to obtain NVM data, since mac80211 isn't even initialized.
Fix this by moving the 'pldr_sync' handling to a different
place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.45a94d480e56.Id9277f1df6a63ab0dfca0d0c0f448c759e1b8e73@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few lines above, space is kzalloc()'ed for:
sizeof(struct iwl_nvm_data) +
sizeof(struct ieee80211_channel) +
sizeof(struct ieee80211_rate)
'mvm->nvm_data' is a 'struct iwl_nvm_data', so it is fine.
At the end of this structure, there is the 'channels' flex array.
Each element is of type 'struct ieee80211_channel'.
So only 1 element is allocated in this array.
When doing:
mvm->nvm_data->bands[0].channels = mvm->nvm_data->channels;
We point at the first element of the 'channels' flex array.
So this is fine.
However, when doing:
mvm->nvm_data->bands[0].bitrates =
(void *)((u8 *)mvm->nvm_data->channels + 1);
because of the "(u8 *)" cast, we add only 1 to the address of the beginning
of the flex array.
It is likely that we want point at the 'struct ieee80211_rate' allocated
just after.
Remove the spurious casting so that the pointer arithmetic works as
expected.
Fixes: 8ca151b568 ("iwlwifi: add the MVM driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/23f0ec986ef1529055f4f93dcb3940a6cf8d9a94.1690143750.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Debugging indicates that nothing else is clearing the info->flags,
so some frames were flagged as ACKed when they should not be.
Explicitly clear the ack flag to ensure this does not happen.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230808205605.4105670-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some cases of restart crashing here have been reported,
while we figure out where this is going wrong, check
the link more carefully to avoid the crash.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230830112059.2b81f52ce18e.I8f3b1962013107e2d7491d817c3349359341c6ee@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware was trying to report the B2 RU allocation in
the place previously used here as well, but there's a HW
block that clears the lower 8 bits in this metadata word
even in sniffer mode. Thus, firmware moved B2 to another
place, follow that.
There's no need to detect the version since moving it to
the other place if firmware didn't just means that we'll
continue to report the (erroneous) zero value, and it's
not really something we can detect from the firmware now.
While debugging this we realized that the comments about
placement in the metadata dwords are wrong, update them.
Reported-by: Youhan Kim <youhank@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230830112059.dec7f1e07ff8.I623fee2d710cc7b6f392d65b708883ed58632b45@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
