Some recent upstream debugging uncovered the fact that in
iwlwifi, the TXQ list manipulation is racy.
Introduce a new state bit for when the TXQ is completely
ready and can be used without locking, and if that's not
set yet acquire the lock to check everything correctly.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This could race if the queue is redirected while full, then
the flushing internally would start it while it's not yet
usable again. Fix it by using two state bits instead of just
one.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's a rate->index that maps inside the range but
to an uninitialized value, then that's also a bad rate,
avoid printing "(nil)" in that case and rather print the
"BAD_RATE" string instead as in the else branch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.06b38d160fc5.I45a9254d3658b1ce796aa4c427193d3cbf638d7e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cppcheck reports
[drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2686]: (warning) Assignment of function parameter has no effect outside the function. Did you forget dereferencing it?
The setting of the 'sta' parameter is not needed. In the if-check that sets it
to NULL, mvm_sta is also set to NULL. Then the next statement checks if
mvm_sta is NULL and does an early return. So remove setting sta.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.711fe28cfdd6.I2f723f9d44f65720baaf3e84b72109759350a8f5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is another patch in the series adding all the ops
for the new MLD ieee80211_ops.
The callback added here uses the new MLD FW API
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.5d4bcd384425.I263eef3aad8efe23a597843fe7c56924038c8fdc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since parts of the functionality of this function is going to be used
also by the MLD version of it, put in a separate function the parts
that are common for both MLD and non-MLD modes.
The common function will later be used in the MLD ops.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.fa05929badb9.I2222dc86cf7d7a7bb58c6a2f2529c8089bfe58b4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is another patch in the series adding all the ops
for the new MLD ieee80211_ops.
The callback added here uses the new MLD FW API.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.d3753975e720.I45f89cc81370d2cf8d4f51748ccb3ec675eff1bd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since parts of the functionality of this function is going to be used
also by the MLD version of it, put in a separate function the parts
that are common for both MLD and non-MLD modes.
The common function will later be used in the MLD ops.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.844755701cac.I1c650718ad2381eabc38f4103c1aac67936a1ffc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the MLD mode and its new APIs are introduced,
we've decided to add a new ieee80211_ops dedicated for
MLD callbacks. Add the MLD remove_interface() callback
which uses the new MLD APIs.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.b87c5c0a4b6b.I631173a73d6ffd7232aa539ea8b356a222fac398@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the MLD mode and its new APIs are introduced,
we've decided to add a new ieee80211_ops dedicated for
MLD callbacks. Add the MLD add_interface() callback
which uses the new MLD APIs added the previous patches.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.6adc29bff39b.I97ed469028009be9392dcc6f7b5ffbe45f4b2c43@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a part of the new MLD FW API changes, we have new commands for STA
related operations (add/remove/aux/disable tx).
Add structures and enum definitions, along with part of the functions
that sends this commands.
This functions will be in used and more will be added in the next patches.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.132873ce015c.I7b12a77e5be066730762e6ceeeaa7190293c3df1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a part of the new MLD FW API changes, we have a new LINK command
to add/remove/configure a link.
Add structures and enum definitions, along with the functions that
sends this command (i.e. add, remove and change mac ctxt).
These functions will be in used in the next patches.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.d7808329effb.I13bea2db206b78540bc866bc3ab755ad5be78c53@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a part of the new MLD FW API changes, we have a new MAC CTXT command.
Add structures and enum definitions, along with the functions that
sends this command (i.e. add, remove and change mac ctxt).
This functions will be in used in the next patches.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.99a41a5bc55f.I310312c829f5f2f69b64fcddce487b1eab80165b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor MAC_CONTEXT_CMD sending flow:
1. As the new MLD API is introduced, there are some common fields in
both the old and new APIs. The MAC_CONTEXT_CMD of the non-MLD API
has common fields with the link and mac commands of the new MLD API.
Put this common parts in functions so it can be used later by the
new MLD API.
2. Use iwl_mvm_mac_ctxt_send_cmd when removing a mac instead of
implementing the same functionality once again.
3. Change the debug print when sending the command to be more specific,
so it will be easy to distinguish later if the old or new mac command
was sent.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.3ab62700db4e.I2e353b308667c215aa456c160e0d90de2b9b85cc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor STA_HE_CTXT_CMD sending flow:
1. As the new MLD API is introduced, there are some common fields in
both the old and new APIs. The STA_HE_CTXT_CMD of the non-MLD API
has common fields with the link and mac commands of the new MLD API.
Put this common parts in functions so it can be used later by the
new MLD API.
2. The HE capability which indicates whether the NIC is ack-enabled or
not is the same for all bands. No need to take it from the specific
band which is currently in use. Take it from the low band - this
simplifies the code and doesn't require a phy_ctxt.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.7ca960596953.Ifc3e816461abbd69c6fd87752342afcedfebc293@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In FW restart scenarios, we allocate the queues from the
iwl_mvm_realloc_queues_after_restart() function, but that
is called before we insert the station ID into our map
(mvm->fw_id_to_mac_id).
However, in all cases where we're actually allocating a
queue for a "real" (not bcast, aux, ...) station we have
the sta pointer already, so just pass it along to use it
instead of looking it up.
This fixes an issue where after restart we only allocated
a queue of size 16 (due to the ordering issue described
above), and thus never got good throughput again since no
aggregates could be formed on transmit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.4d70868003e8.I3476fee5c12f5b1af2be5e2f38a9df7d66d02b62@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Major changes:
cfg80211
* 6 GHz improvements
* HW timestamping support
* support for randomized auth/deauth TA for PASN privacy
(also for mac80211)
mac80211
* radiotap TLV and EHT support for the iwlwifi sniffer
* HW timestamping support
* per-link debugfs for multi-link
brcmfmac
* support for Apple (M1 Pro/Max) devices
iwlwifi
* support for a few new devices
* EHT sniffer support
rtw88
* better support for some SDIO devices
(e.g. MAC address from efuse)
rtw89
* HW scan support for 8852b
* better support for 6 GHz scanning
-----BEGIN PGP SIGNATURE-----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=sPir
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless-next patches for 6.4
Major changes:
cfg80211
* 6 GHz improvements
* HW timestamping support
* support for randomized auth/deauth TA for PASN privacy
(also for mac80211)
mac80211
* radiotap TLV and EHT support for the iwlwifi sniffer
* HW timestamping support
* per-link debugfs for multi-link
brcmfmac
* support for Apple (M1 Pro/Max) devices
iwlwifi
* support for a few new devices
* EHT sniffer support
rtw88
* better support for some SDIO devices
(e.g. MAC address from efuse)
rtw89
* HW scan support for 8852b
* better support for 6 GHz scanning
* tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (84 commits)
wifi: iwlwifi: mvm: fix EOF bit reporting
wifi: iwlwifi: Do not include radiotap EHT user info if not needed
wifi: iwlwifi: mvm: add EHT RU allocation to radiotap
wifi: iwlwifi: Update logs for yoyo reset sw changes
wifi: iwlwifi: mvm: clean up duplicated defines
wifi: iwlwifi: rs-fw: break out for unsupported bandwidth
wifi: iwlwifi: Add support for B step of BnJ-Fm4
wifi: iwlwifi: mvm: make flush code a bit clearer
wifi: iwlwifi: mvm: avoid UB shift of snif_queue
wifi: iwlwifi: mvm: add primary 80 known for EHT radiotap
wifi: iwlwifi: mvm: parse FW frame metadata for EHT sniffer mode
wifi: iwlwifi: mvm: decode USIG_B1_B7 RU to nl80211 RU width
wifi: iwlwifi: mvm: rename define to generic name
wifi: iwlwifi: mvm: allow Microsoft to use TAS
wifi: iwlwifi: mvm: add all EHT based on data0 info from HW
wifi: iwlwifi: mvm: add EHT radiotap info based on rate_n_flags
wifi: iwlwifi: mvm: add an helper function radiotap TLVs
wifi: radiotap: separate vendor TLV into header/content
wifi: iwlwifi: reduce verbosity of some logging events
wifi: iwlwifi: Adding the code to get RF name for MsP device
...
====================
Link: https://lore.kernel.org/r/20230310120159.36518-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In monitor mode, we try to report the EOF bit on the
first MPDU of an A-MPDU (hardware duplicates this bit
over all MPDUs, so it's only trustable on the first).
However, due to reshuffling in an ealier commit, the
toggle_bit != mvm->ampdu_toggle logic can no longer
work since mvm->ampdu_toggle is now set before this
code runs.
Fix this by tracking the first_subframe status in the
phy data struct and using that instead of checking.
Fixes: f1490546be ("wifi: iwlwifi: mvm: rxmq: refactor mac80211 rx_status setting")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124407.e273aa0d3fdc.I77db4cc247898eae8a98b80659386d6737052b95@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not include user information in radtiotap EHT data for EHT sounding
NDP as the frame doesn't include the user specific field. Instead,
encode the NSS and the beamforming information in the EHT data.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124407.ac6474ded9bd.I9655589e9afbacc16820f35f6f5d90c6a91b8b05@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT, HE and EHT rates use the same bits for NSS, so no need for
defines per PHY version.
Also use spatch to replace bit manipulation with FIELD_GET:
@@
identifier rate;
@@
-((rate & RATE_MCS_NSS_MSK) >> RATE_MCS_NSS_POS)
+FIELD_GET(RATE_MCS_NSS_MSK, rate)
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124407.167ed9477aa8.Ibd8e71d31896e8d8f067ce4e3a6e9a0e86c78f3f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the for loop runs also over unsupported bandwidth in the
command, shorten the path in case we don't support it.
Also use the right macro for setting BW20.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124407.0264ba9df63b.I6c7c9efc806e0ffb7cb3b6051b2d109646e8708c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the old TX API we need the tfd_queue_msk, but for the
new TX API we don't need it here because we add it to the
station later. However, for the new API mvm->snif_queue is
set to IWL_MVM_INVALID_QUEUE == 0xffff, so the BIT() here
is undefined behaviour.
Since we don't need the tfd_queue_msk value for the new TX
API at all, simply fill it in only for the old API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124407.b8da0b7eb194.I53744fd7cfb6e146a9393272a2a61852841238d9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Calculate the position of the control channel in the wide channel
based on the chandef, this is used to obtain the value of N in
802.11be D1.5 Table 9-53a in the column PHY MU/MRU index.
To avoid the need to calculate every frame the value, do it once
monitor vif is added.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124407.fe9a5b58e241.I291ee480252d098f62d9ec39040284d3e521d88e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In EHT sniffer mode DW4 is all used for sniffer data (unlike we have in
HE mode), so move the full DW4 into a union, and we extract the new data5
used for parsing USIG info and set all to radiotap TLVs with the
extracted data.
Also parse OFDM_RX_VECTOR_USIG_A1_OUT and OFDM_RX_VECTOR_USIG_A2_OUT for
rx_no_data notification.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124407.557d3870753b.I4e9fa4d21900a187753529d46956ba2a7ee75fda@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To be able to use a general function later for any kind of
TLV, separate the vendor TLV header/content in the structs.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124407.8ac5195bb3e6.I19ad99c1ad3108453aede64bddf6ef1a7c4a0b74@changeid
[separate from the original combined patch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Although no data is presented in the skb, but upper layers need it for
calculating where radio tap header are done, so we mark it.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124406.8f53cc8579bf.I8819c005b4953cea03346d0aff82b31d94f79fe5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new TLV format enables adding TLVs after the fixed
fields in radiotap, as part of the radiotap header.
Support this and move vendor data to the TLV format,
allowing a reuse of the RX_FLAG_RADIOTAP_VENDOR_DATA as
the new RX_FLAG_RADIOTAP_TLV_AT_END flag.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.b18fd5da8477.I576400ec40a7b35ef97a3b09a99b3a49e9174786@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The thermal zone device structure is exposed to the different drivers
and obviously they access the internals while that should be
restricted to the core thermal code.
In order to self-encapsulate the thermal core code, we need to prevent
the drivers accessing directly the thermal zone structure and provide
accessor functions to deal with.
Use the devdata accessor introduced in the previous patch.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> #mlxsw
Acked-by: Gregory Greenman <gregory.greenman@intel.com> #iwlwifi
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> #power_supply
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> #ahci
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Core
----
- Add dedicated kmem_cache for typical/small skb->head, avoid having
to access struct page at kfree time, and improve memory use.
- Introduce sysctl to set default RPS configuration for new netdevs.
- Define Netlink protocol specification format which can be used
to describe messages used by each family and auto-generate parsers.
Add tools for generating kernel data structures and uAPI headers.
- Expose all net/core sysctls inside netns.
- Remove 4s sleep in netpoll if carrier is instantly detected on boot.
- Add configurable limit of MDB entries per port, and port-vlan.
- Continue populating drop reasons throughout the stack.
- Retire a handful of legacy Qdiscs and classifiers.
Protocols
---------
- Support IPv4 big TCP (TSO frames larger than 64kB).
- Add IP_LOCAL_PORT_RANGE socket option, to control local port range
on socket by socket basis.
- Track and report in procfs number of MPTCP sockets used.
- Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP
path manager.
- IPv6: don't check net.ipv6.route.max_size and rely on garbage
collection to free memory (similarly to IPv4).
- Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).
- ICMP: add per-rate limit counters.
- Add support for user scanning requests in ieee802154.
- Remove static WEP support.
- Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
reporting.
- WiFi 7 EHT channel puncturing support (client & AP).
BPF
---
- Add a rbtree data structure following the "next-gen data structure"
precedent set by recently added linked list, that is, by using
kfunc + kptr instead of adding a new BPF map type.
- Expose XDP hints via kfuncs with initial support for RX hash and
timestamp metadata.
- Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key
to better support decap on GRE tunnel devices not operating
in collect metadata.
- Improve x86 JIT's codegen for PROBE_MEM runtime error checks.
- Remove the need for trace_printk_lock for bpf_trace_printk
and bpf_trace_vprintk helpers.
- Extend libbpf's bpf_tracing.h support for tracing arguments of
kprobes/uprobes and syscall as a special case.
- Significantly reduce the search time for module symbols
by livepatch and BPF.
- Enable cpumasks to be used as kptrs, which is useful for tracing
programs tracking which tasks end up running on which CPUs in
different time intervals.
- Add support for BPF trampoline on s390x and riscv64.
- Add capability to export the XDP features supported by the NIC.
- Add __bpf_kfunc tag for marking kernel functions as kfuncs.
- Add cgroup.memory=nobpf kernel parameter option to disable BPF
memory accounting for container environments.
Netfilter
---------
- Remove the CLUSTERIP target. It has been marked as obsolete
for years, and we still have WARN splats wrt. races of
the out-of-band /proc interface installed by this target.
- Add 'destroy' commands to nf_tables. They are identical to
the existing 'delete' commands, but do not return an error if
the referenced object (set, chain, rule...) did not exist.
Driver API
----------
- Improve cpumask_local_spread() locality to help NICs set the right
IRQ affinity on AMD platforms.
- Separate C22 and C45 MDIO bus transactions more clearly.
- Introduce new DCB table to control DSCP rewrite on egress.
- Support configuration of Physical Layer Collision Avoidance (PLCA)
Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
shared medium Ethernet.
- Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
preemption of low priority frames by high priority frames.
- Add support for controlling MACSec offload using netlink SET.
- Rework devlink instance refcounts to allow registration and
de-registration under the instance lock. Split the code into multiple
files, drop some of the unnecessarily granular locks and factor out
common parts of netlink operation handling.
- Add TX frame aggregation parameters (for USB drivers).
- Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
messages with notifications for debug.
- Allow offloading of UDP NEW connections via act_ct.
- Add support for per action HW stats in TC.
- Support hardware miss to TC action (continue processing in SW from
a specific point in the action chain).
- Warn if old Wireless Extension user space interface is used with
modern cfg80211/mac80211 drivers. Do not support Wireless Extensions
for Wi-Fi 7 devices at all. Everyone should switch to using nl80211
interface instead.
- Improve the CAN bit timing configuration. Use extack to return error
messages directly to user space, update the SJW handling, including
the definition of a new default value that will benefit CAN-FD
controllers, by increasing their oscillator tolerance.
New hardware / drivers
----------------------
- Ethernet:
- nVidia BlueField-3 support (control traffic driver)
- Ethernet support for imx93 SoCs
- Motorcomm yt8531 gigabit Ethernet PHY
- onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
- Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
- Amlogic gxl MDIO mux
- WiFi:
- RealTek RTL8188EU (rtl8xxxu)
- Qualcomm Wi-Fi 7 devices (ath12k)
- CAN:
- Renesas R-Car V4H
Drivers
-------
- Bluetooth:
- Set Per Platform Antenna Gain (PPAG) for Intel controllers.
- Ethernet NICs:
- Intel (1G, igc):
- support TSN / Qbv / packet scheduling features of i226 model
- Intel (100G, ice):
- use GNSS subsystem instead of TTY
- multi-buffer XDP support
- extend support for GPIO pins to E823 devices
- nVidia/Mellanox:
- update the shared buffer configuration on PFC commands
- implement PTP adjphase function for HW offset control
- TC support for Geneve and GRE with VF tunnel offload
- more efficient crypto key management method
- multi-port eswitch support
- Netronome/Corigine:
- add DCB IEEE support
- support IPsec offloading for NFP3800
- Freescale/NXP (enetc):
- enetc: support XDP_REDIRECT for XDP non-linear buffers
- enetc: improve reconfig, avoid link flap and waiting for idle
- enetc: support MAC Merge layer
- Other NICs:
- sfc/ef100: add basic devlink support for ef100
- ionic: rx_push mode operation (writing descriptors via MMIO)
- bnxt: use the auxiliary bus abstraction for RDMA
- r8169: disable ASPM and reset bus in case of tx timeout
- cpsw: support QSGMII mode for J721e CPSW9G
- cpts: support pulse-per-second output
- ngbe: add an mdio bus driver
- usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
- r8152: handle devices with FW with NCM support
- amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
- virtio-net: support multi buffer XDP
- virtio/vsock: replace virtio_vsock_pkt with sk_buff
- tsnep: XDP support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add support for latency TLV (in FW control messages)
- Microchip (sparx5):
- separate explicit and implicit traffic forwarding rules, make
the implicit rules always active
- add support for egress DSCP rewrite
- IS0 VCAP support (Ingress Classification)
- IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS etc.)
- ES2 VCAP support (Egress Access Control)
- support for Per-Stream Filtering and Policing (802.1Q, 8.6.5.1)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- add MAB (port auth) offload support
- enable PTP receive for mv88e6390
- NXP (ocelot):
- support MAC Merge layer
- support for the the vsc7512 internal copper phys
- Microchip:
- lan9303: convert to PHYLINK
- lan966x: support TC flower filter statistics
- lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
- lan937x: support Credit Based Shaper configuration
- ksz9477: support Energy Efficient Ethernet
- other:
- qca8k: convert to regmap read/write API, use bulk operations
- rswitch: Improve TX timestamp accuracy
- Intel WiFi (iwlwifi):
- EHT (Wi-Fi 7) rate reporting
- STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware.
- Qualcomm 802.11ax WiFi (ath11k):
- IPQ5018 support
- Fine Timing Measurement (FTM) responder role support
- channel 177 support
- MediaTek WiFi (mt76):
- per-PHY LED support
- mt7996: EHT (Wi-Fi 7) support
- Wireless Ethernet Dispatch (WED) reset support
- switch to using page pool allocator
- RealTek WiFi (rtw89):
- support new version of Bluetooth co-existance
- Mobile:
- rmnet: support TX aggregation.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmP1VIYACgkQMUZtbf5S
IrvsChAApz0rNL/sPKxXTEfxZ1tN7D3sYxYKQPomxvl5BV+MvicrLddJy3KmzEFK
nnJNO3nuRNuH422JQ/ylZ4mGX1opa6+5QJb0UINImXUI7Fm8HHBIuPGkv7d5CheZ
7JexFqjPJXUy9nPyh1Rra+IA9AcRd2U7jeGEZR38wb99bHJQj5Bzdk20WArEB0el
n44aqg49LXH71bSeXRz77x5SjkwVtYiccQxLcnmTbjLU2xVraLvI2J+wAhHnVXWW
9lrU1+V4Ex2Xcd1xR0L0cHeK+meP1TrPRAeF+JDpVI3a/zJiE7cZjfHdG/jH5xWl
leZJqghVozrZQNtewWWO7XhUFhMDgFu3W/1vNLjSHPZEqaz1JpM67J1+ql6s63l4
LMWoXbcYZz+SL9ZRCoPkbGue/5fKSHv8/Jl9Sh58+eTS+c/zgN8uFGRNFXLX1+EP
n8uvt985PxMd6x1+dHumhOUzxnY4Sfi1vjitSunTsNFQ3Cmp4SO0IfBVJWfLUCuC
xz5hbJGJJbSpvUsO+HWyCg83E5OWghRE/Onpt2jsQSZCrO9HDg4FRTEf3WAMgaqc
edb5KfbRZPTJQM08gWdluXzSk1nw3FNP2tXW4XlgUrEbjb+fOk0V9dQg2gyYTxQ1
Nhvn8ZQPi6/GMMELHAIPGmmW1allyOGiAzGlQsv8EmL+OFM6WDI=
=xXhC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Add dedicated kmem_cache for typical/small skb->head, avoid having
to access struct page at kfree time, and improve memory use.
- Introduce sysctl to set default RPS configuration for new netdevs.
- Define Netlink protocol specification format which can be used to
describe messages used by each family and auto-generate parsers.
Add tools for generating kernel data structures and uAPI headers.
- Expose all net/core sysctls inside netns.
- Remove 4s sleep in netpoll if carrier is instantly detected on
boot.
- Add configurable limit of MDB entries per port, and port-vlan.
- Continue populating drop reasons throughout the stack.
- Retire a handful of legacy Qdiscs and classifiers.
Protocols:
- Support IPv4 big TCP (TSO frames larger than 64kB).
- Add IP_LOCAL_PORT_RANGE socket option, to control local port range
on socket by socket basis.
- Track and report in procfs number of MPTCP sockets used.
- Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
manager.
- IPv6: don't check net.ipv6.route.max_size and rely on garbage
collection to free memory (similarly to IPv4).
- Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).
- ICMP: add per-rate limit counters.
- Add support for user scanning requests in ieee802154.
- Remove static WEP support.
- Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
reporting.
- WiFi 7 EHT channel puncturing support (client & AP).
BPF:
- Add a rbtree data structure following the "next-gen data structure"
precedent set by recently added linked list, that is, by using
kfunc + kptr instead of adding a new BPF map type.
- Expose XDP hints via kfuncs with initial support for RX hash and
timestamp metadata.
- Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
better support decap on GRE tunnel devices not operating in collect
metadata.
- Improve x86 JIT's codegen for PROBE_MEM runtime error checks.
- Remove the need for trace_printk_lock for bpf_trace_printk and
bpf_trace_vprintk helpers.
- Extend libbpf's bpf_tracing.h support for tracing arguments of
kprobes/uprobes and syscall as a special case.
- Significantly reduce the search time for module symbols by
livepatch and BPF.
- Enable cpumasks to be used as kptrs, which is useful for tracing
programs tracking which tasks end up running on which CPUs in
different time intervals.
- Add support for BPF trampoline on s390x and riscv64.
- Add capability to export the XDP features supported by the NIC.
- Add __bpf_kfunc tag for marking kernel functions as kfuncs.
- Add cgroup.memory=nobpf kernel parameter option to disable BPF
memory accounting for container environments.
Netfilter:
- Remove the CLUSTERIP target. It has been marked as obsolete for
years, and we still have WARN splats wrt races of the out-of-band
/proc interface installed by this target.
- Add 'destroy' commands to nf_tables. They are identical to the
existing 'delete' commands, but do not return an error if the
referenced object (set, chain, rule...) did not exist.
Driver API:
- Improve cpumask_local_spread() locality to help NICs set the right
IRQ affinity on AMD platforms.
- Separate C22 and C45 MDIO bus transactions more clearly.
- Introduce new DCB table to control DSCP rewrite on egress.
- Support configuration of Physical Layer Collision Avoidance (PLCA)
Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
shared medium Ethernet.
- Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
preemption of low priority frames by high priority frames.
- Add support for controlling MACSec offload using netlink SET.
- Rework devlink instance refcounts to allow registration and
de-registration under the instance lock. Split the code into
multiple files, drop some of the unnecessarily granular locks and
factor out common parts of netlink operation handling.
- Add TX frame aggregation parameters (for USB drivers).
- Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
messages with notifications for debug.
- Allow offloading of UDP NEW connections via act_ct.
- Add support for per action HW stats in TC.
- Support hardware miss to TC action (continue processing in SW from
a specific point in the action chain).
- Warn if old Wireless Extension user space interface is used with
modern cfg80211/mac80211 drivers. Do not support Wireless
Extensions for Wi-Fi 7 devices at all. Everyone should switch to
using nl80211 interface instead.
- Improve the CAN bit timing configuration. Use extack to return
error messages directly to user space, update the SJW handling,
including the definition of a new default value that will benefit
CAN-FD controllers, by increasing their oscillator tolerance.
New hardware / drivers:
- Ethernet:
- nVidia BlueField-3 support (control traffic driver)
- Ethernet support for imx93 SoCs
- Motorcomm yt8531 gigabit Ethernet PHY
- onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
- Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
- Amlogic gxl MDIO mux
- WiFi:
- RealTek RTL8188EU (rtl8xxxu)
- Qualcomm Wi-Fi 7 devices (ath12k)
- CAN:
- Renesas R-Car V4H
Drivers:
- Bluetooth:
- Set Per Platform Antenna Gain (PPAG) for Intel controllers.
- Ethernet NICs:
- Intel (1G, igc):
- support TSN / Qbv / packet scheduling features of i226 model
- Intel (100G, ice):
- use GNSS subsystem instead of TTY
- multi-buffer XDP support
- extend support for GPIO pins to E823 devices
- nVidia/Mellanox:
- update the shared buffer configuration on PFC commands
- implement PTP adjphase function for HW offset control
- TC support for Geneve and GRE with VF tunnel offload
- more efficient crypto key management method
- multi-port eswitch support
- Netronome/Corigine:
- add DCB IEEE support
- support IPsec offloading for NFP3800
- Freescale/NXP (enetc):
- support XDP_REDIRECT for XDP non-linear buffers
- improve reconfig, avoid link flap and waiting for idle
- support MAC Merge layer
- Other NICs:
- sfc/ef100: add basic devlink support for ef100
- ionic: rx_push mode operation (writing descriptors via MMIO)
- bnxt: use the auxiliary bus abstraction for RDMA
- r8169: disable ASPM and reset bus in case of tx timeout
- cpsw: support QSGMII mode for J721e CPSW9G
- cpts: support pulse-per-second output
- ngbe: add an mdio bus driver
- usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
- r8152: handle devices with FW with NCM support
- amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
- virtio-net: support multi buffer XDP
- virtio/vsock: replace virtio_vsock_pkt with sk_buff
- tsnep: XDP support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add support for latency TLV (in FW control messages)
- Microchip (sparx5):
- separate explicit and implicit traffic forwarding rules, make
the implicit rules always active
- add support for egress DSCP rewrite
- IS0 VCAP support (Ingress Classification)
- IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
etc.)
- ES2 VCAP support (Egress Access Control)
- support for Per-Stream Filtering and Policing (802.1Q,
8.6.5.1)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- add MAB (port auth) offload support
- enable PTP receive for mv88e6390
- NXP (ocelot):
- support MAC Merge layer
- support for the the vsc7512 internal copper phys
- Microchip:
- lan9303: convert to PHYLINK
- lan966x: support TC flower filter statistics
- lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
- lan937x: support Credit Based Shaper configuration
- ksz9477: support Energy Efficient Ethernet
- other:
- qca8k: convert to regmap read/write API, use bulk operations
- rswitch: Improve TX timestamp accuracy
- Intel WiFi (iwlwifi):
- EHT (Wi-Fi 7) rate reporting
- STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware.
- Qualcomm 802.11ax WiFi (ath11k):
- IPQ5018 support
- Fine Timing Measurement (FTM) responder role support
- channel 177 support
- MediaTek WiFi (mt76):
- per-PHY LED support
- mt7996: EHT (Wi-Fi 7) support
- Wireless Ethernet Dispatch (WED) reset support
- switch to using page pool allocator
- RealTek WiFi (rtw89):
- support new version of Bluetooth co-existance
- Mobile:
- rmnet: support TX aggregation"
* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
page_pool: add a comment explaining the fragment counter usage
net: ethtool: fix __ethtool_dev_mm_supported() implementation
ethtool: pse-pd: Fix double word in comments
xsk: add linux/vmalloc.h to xsk.c
sefltests: netdevsim: wait for devlink instance after netns removal
selftest: fib_tests: Always cleanup before exit
net/mlx5e: Align IPsec ASO result memory to be as required by hardware
net/mlx5e: TC, Set CT miss to the specific ct action instance
net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
net/mlx5: Refactor tc miss handling to a single function
net/mlx5: Kconfig: Make tc offload depend on tc skb extension
net/sched: flower: Support hardware miss to tc action
net/sched: flower: Move filter handle initialization earlier
net/sched: cls_api: Support hardware miss to tc action
net/sched: Rename user cookie and act cookie
sfc: fix builds without CONFIG_RTC_LIB
sfc: clean up some inconsistent indentings
net/mlx4_en: Introduce flexible array to silence overflow warning
net: lan966x: Fix possible deadlock inside PTP
net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
...
Read the STEP equalizer parameters from the BIOS during init
and transfer it to the firmware.
This table provides values to configure an equalizer at the transmitter
that can be used to compensate for PCB channel attenuation.
Signed-off-by: Ayala Barazani <ayala.barazani@intel.com>
Link: https://lore.kernel.org/r/20230127002430.f25f871c5e17.I8390ab916c8f681229433ebc576ed37a594c6d30@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Instead of calculating the offset to the 802.11 header based on radiotap
bits and length, shorten the code path by always setting the MAC header
in the skb and using skb_mac_header().
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20230127002430.3ec5493934a4.I1d41a2af28588b5899fcd2402f8c4bd8cc29a12e@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
This change fixes the checkpatch warning described in this commit
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230127002430.a25158d58fd7.Ibfe217f12a63c1d5349218e74c4b802c70c13c7c@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Now with all the prework, this is fairly simple, just report the
new bandwidth and RX_ENC_EHT type in RX, and for now just do a
minimal report of the EHT TLC rate in iwl_mvm_set_sta_rate().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230109130329.5f34d73d1f74.Ib27ae7bd23bc152d61021fd73aabdc76679b9fe4@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
The get_trip_temp, get_trip_hyst and get_trip_type are handled by the
get_trip_point().
The set_trip_temp() generic function does some checks which are no
longer needed in the set_trip_point() ops.
Convert ops content logic into generic trip points and register them
with the thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221014073253.3719911-1-daniel.lezcano@linaro.org
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core
----
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations.
- Add inet drop monitor support.
- A few GRO performance improvements.
- Add infrastructure for atomic dev stats, addressing long standing
data races.
- De-duplicate common code between OVS and conntrack offloading
infrastructure.
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements.
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up
the workload with the number of available CPUs.
- Add the helper support for connection-tracking OVS offload.
BPF
---
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF.
- Make cgroup local storage available to non-cgroup attached BPF
programs.
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers.
- A relevant bunch of BPF verifier fixes and improvements.
- Veristat tool improvements to support custom filtering, sorting,
and replay of results.
- Add LLVM disassembler as default library for dumping JITed code.
- Lots of new BPF documentation for various BPF maps.
- Add bpf_rcu_read_{,un}lock() support for sleepable programs.
- Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs.
- Add support storing struct task_struct objects as kptrs in maps.
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values.
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions.
Protocols
---------
- TCP: implement Protective Load Balancing across switch links.
- TCP: allow dynamically disabling TCP-MD5 static key, reverting
back to fast[er]-path.
- UDP: Introduce optional per-netns hash lookup table.
- IPv6: simplify and cleanup sockets disposal.
- Netlink: support different type policies for each generic
netlink operation.
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support.
- MPTCP: add netlink notification support for listener sockets
events.
- SCTP: add VRF support, allowing sctp sockets binding to VRF
devices.
- Add bridging MAC Authentication Bypass (MAB) support.
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios.
- More work for Wi-Fi 7 support, comprising conversion of all
the existing drivers to internal TX queue usage.
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading.
- IPSec: extended ack support for more descriptive XFRM error
reporting.
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking.
- IEEE 802154: synchronous send frame and extended filtering
support, initial support for scanning available 15.4 networks.
- Tun: bump the link speed from 10Mbps to 10Gbps.
- Tun/VirtioNet: implement UDP segmentation offload support.
Driver API
----------
- PHY/SFP: improve power level switching between standard
level 1 and the higher power levels.
- New API for netdev <-> devlink_port linkage.
- PTP: convert existing drivers to new frequency adjustment
implementation.
- DSA: add support for rx offloading.
- Autoload DSA tagging driver when dynamically changing protocol.
- Add new PCP and APPTRUST attributes to Data Center Bridging.
- Add configuration support for 800Gbps link speed.
- Add devlink port function attribute to enable/disable RoCE and
migratable.
- Extend devlink-rate to support strict prioriry and weighted fair
queuing.
- Add devlink support to directly reading from region memory.
- New device tree helper to fetch MAC address from nvmem.
- New big TCP helper to simplify temporary header stripping.
New hardware / drivers
----------------------
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches.
- Marvel Prestera AC5X Ethernet Switch.
- WangXun 10 Gigabit NIC.
- Motorcomm yt8521 Gigabit Ethernet.
- Microchip ksz9563 Gigabit Ethernet Switch.
- Microsoft Azure Network Adapter.
- Linux Automation 10Base-T1L adapter.
- PHY:
- Aquantia AQR112 and AQR412.
- Motorcomm YT8531S.
- PTP:
- Orolia ART-CARD.
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices.
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices.
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets.
- Realtek RTL8852BE and RTL8723DS.
- Cypress.CYW4373A0 WiFi + Bluetooth combo device.
Drivers
-------
- CAN:
- gs_usb: bus error reporting support.
- kvaser_usb: listen only and bus error reporting support.
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping.
- implement devlink-rate support.
- support direct read from memory.
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate.
- Support for enhanced events compression.
- extend H/W offload packet manipulation capabilities.
- implement IPSec packet offload mode.
- nVidia/Mellanox (mlx4):
- better big TCP support.
- Netronome Ethernet NICs (nfp):
- IPsec offload support.
- add support for multicast filter.
- Broadcom:
- RSS and PTP support improvements.
- AMD/SolarFlare:
- netlink extened ack improvements.
- add basic flower matches to offload, and related stats.
- Virtual NICs:
- ibmvnic: introduce affinity hint support.
- small / embedded:
- FreeScale fec: add initial XDP support.
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood.
- TI am65-cpsw: add suspend/resume support.
- Mediatek MT7986: add RX wireless wthernet dispatch support.
- Realtek 8169: enable GRO software interrupt coalescing per
default.
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP.
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support.
- add ip6gre support.
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support.
- enable flow offload support.
- Renesas:
- add rswitch R-Car Gen4 gPTP support.
- Microchip (lan966x):
- add full XDP support.
- add TC H/W offload via VCAP.
- enable PTP on bridge interfaces.
- Microchip (ksz8):
- add MTU support for KSZ8 series.
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan.
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support.
- add ack signal support.
- enable coredump support.
- remain_on_channel support.
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities.
- 320 MHz channels support.
- RealTek WiFi (rtw89):
- new dynamic header firmware format support.
- wake-over-WLAN support.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=CbJC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
The CSR_HW_IF_CONFIG_REG register is no longer in use from
IWL_DEVICE_FAMILY_AX210 and on.
This register uses now for CSR_CTXT_INFO_BOOT_CTRL
which has a different meaning and a different format.
Currently we're writing to the register according to
CSR_HW_IF_CONFIG_REGs format, regardless to the device family.
This causes to miss-interpretation of the register value, as it is
parsed according to CSR_CTXT_INFO_BOOT_CTRLs format for devices
families >= IWL_DEVICE_FAMILY_AX210.
Fix this by writing to the register according to the old format
only for the relevant hardware.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221205102808.8e91eb10dc7d.I3882a2452785ef8b455d99af235e4477917bf46d@changeid
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].
This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.
While at it, stop using the unnecessary _safe() variant.
[1] https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
[change to not use _safe variant]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221205102808.e4882dc35543.I32b2b945ba234de72ee119fc20f5b8be02b6a3f2@changeid
When doing the PLDR flow, the fw goes through a re-read and needs
PCI re-enumeration in order to recover. In this case, skip the mac
start retry and fw dumps as all the fw and registers are invalid
until the PCI re-enumeration.
In addition, print the register that shows the re-read counter
when loading the fw.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Link: https://lore.kernel.org/r/20221123225313.9ae77968961e.Ie06e886cef4b5921b65dacb7724db1276bed38cb@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
In an EHT connection fill in the HE context command
with PPE Thresholds field from EHT Capabilities IE.
If PPE Thresholds field presents only in HE Capabilities IE,
take the thresholds from there.
If it's not present in both - set the Common Nominal Packet Padding
field from EHT Capabilities IE.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/r/20221122220713.062ac86110f2.I0bcd5ee35f4d987a49f15501985f90e0d3ce7590@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Rate scale needs to be configured to what MCS it can use per BW and NSS,
this is done by parsing our capabilities of TX and peer's capabilities of
RX and setting the minimum for rate scale usage.
Also do some cleanup removing redundant enum defines not used by
FW/Driver.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20221122220713.f71f3b4c4583.I7b5e8071df91146c4bee3e9bcb7ad62595b275e1@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
These cases were done with this Coccinelle:
@@
expression H;
expression L;
@@
- (get_random_u32_below(H) + L)
+ get_random_u32_inclusive(L, H + L - 1)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- + E
- - E
)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- - E
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- - E
+ F
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- + E
+ F
- - E
)
And then subsequently cleaned up by hand, with several automatic cases
rejected if it didn't make sense contextually.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is a simple mechanical transformation done by:
@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Reviewed-by: SeongJae Park <sj@kernel.org> # for damon
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> # for arm
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
If the FW needs to do OTP re-read, the driver must notify CSME before
loading the FW so CSME will not try to access the NIC during the
re-read. Once the alive notification is received, CSME is notified
that NIC access is allowed again.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221102165239.49eb8c6d455f.I7f0a5debb2d3d662a4151199bbec24613f324c13@changeid
When setting the rate for Tx, the code tried to get the lowest
allowed rate but without considering the BSS basic rates. Fix this
by considering the basic rates.
In addition, declare support for configuring beacon Tx rate and when
configured use the configured Tx beacon rate to set beacon tx command rate.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221102165239.be8403f0d5c0.I7d141646746b96310efd75fc77ca9aebc61aefcc@changeid
In order to support MLD, the key API is also changing to have
station masks instead of just the station ID etc. Change the
driver to support this, and add the new code in a new file so
it's more clearly separated.
For now this isn't separated at the mac80211 ops level, which
we wanted to do, but we're calling these functions in a place
when pre-start keys are installed in iwl_mvm_start_ap_ibss(),
and the function has some glue logic to mac80211. We may want
to change that later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221102165239.ed9ccd814abc.Iacc7360de68807fbac19e5b67c86504b39cc15df@changeid
In some rare occasions, the firmware may let some frames with invalid
rates, such as CCK rates on the high band, come through. This causes
the driver to issue a warning, but since this is a possible issue and
it's not really a bug in the driver, convert the warning into an
error.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221102165239.3d3673c70556.I13464b11d405fd6021618b0a32404cecb7e9ac51@changeid
For Bz A-step hardware, the checksum offload is broken and
we need to use the old way, which is still there. Do that,
which requires taking the checksum capability bits out of
the IWL_DEVICE_BZ macro and listing them individually.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221102165239.6bc379f1b0b1.I204223f1b1c2fe26f414aea6679ef7fce681c33a@changeid
Devices with new Tx API have the IV introduced by the HW and it is not
present in the skb at all. Hence we don't need to tell
iwl_mvm_mei_tx_copy_to_csme to jump over 8 bytes to get to the ethernet
header.
Fixes: 2da4366f9e ("iwlwifi: mei: add the driver to allow cooperation with CSME")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221030191011.12dc42133502.Idd744ffeeb84b880eb497963ee02563cbb959a42@changeid
It is possible that CSME will try to take ownership while the driver
is stopping. In this case, if the CSME takes ownership message arrives
after the driver started unregistering, the iwl_mei_cache->ops is
already invalid, so the host will not answer with the ownership
confirmed message.
Similarly, if the take ownership message arrived after the mac was
stopped or when iwl_mvm_up() failed, setting rfkill will not trigger
sending the confirm message. As a result, CSME will not take
ownership, which will result in a disconnection.
Fix it by sending the ownership confirmed message immediately in such
cases.
Fixes: 2da4366f9e ("iwlwifi: mei: add the driver to allow cooperation with CSME")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221030191011.b2a4c009e3e6.I7f931b7ee8b168e8ac88b11f23bff98b7ed3cb19@changeid
-----BEGIN PGP SIGNATURE-----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=M+mV
-----END PGP SIGNATURE-----
Merge tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull more random number generator updates from Jason Donenfeld:
"This time with some large scale treewide cleanups.
The intent of this pull is to clean up the way callers fetch random
integers. The current rules for doing this right are:
- If you want a secure or an insecure random u64, use get_random_u64()
- If you want a secure or an insecure random u32, use get_random_u32()
The old function prandom_u32() has been deprecated for a while
now and is just a wrapper around get_random_u32(). Same for
get_random_int().
- If you want a secure or an insecure random u16, use get_random_u16()
- If you want a secure or an insecure random u8, use get_random_u8()
- If you want secure or insecure random bytes, use get_random_bytes().
The old function prandom_bytes() has been deprecated for a while
now and has long been a wrapper around get_random_bytes()
- If you want a non-uniform random u32, u16, or u8 bounded by a
certain open interval maximum, use prandom_u32_max()
I say "non-uniform", because it doesn't do any rejection sampling
or divisions. Hence, it stays within the prandom_*() namespace, not
the get_random_*() namespace.
I'm currently investigating a "uniform" function for 6.2. We'll see
what comes of that.
By applying these rules uniformly, we get several benefits:
- By using prandom_u32_max() with an upper-bound that the compiler
can prove at compile-time is ≤65536 or ≤256, internally
get_random_u16() or get_random_u8() is used, which wastes fewer
batched random bytes, and hence has higher throughput.
- By using prandom_u32_max() instead of %, when the upper-bound is
not a constant, division is still avoided, because
prandom_u32_max() uses a faster multiplication-based trick instead.
- By using get_random_u16() or get_random_u8() in cases where the
return value is intended to indeed be a u16 or a u8, we waste fewer
batched random bytes, and hence have higher throughput.
This series was originally done by hand while I was on an airplane
without Internet. Later, Kees and I worked on retroactively figuring
out what could be done with Coccinelle and what had to be done
manually, and then we split things up based on that.
So while this touches a lot of files, the actual amount of code that's
hand fiddled is comfortably small"
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove unused functions
treewide: use get_random_bytes() when possible
treewide: use get_random_u32() when possible
treewide: use get_random_{u8,u16}() when possible, part 2
treewide: use get_random_{u8,u16}() when possible, part 1
treewide: use prandom_u32_max() when possible, part 2
treewide: use prandom_u32_max() when possible, part 1
Rather than incurring a division or requesting too many random bytes for
the given range, use the prandom_u32_max() function, which only takes
the minimum required bytes from the RNG and avoids divisions. This was
done mechanically with this coccinelle script:
@basic@
expression E;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
typedef u64;
@@
(
- ((T)get_random_u32() % (E))
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ((E) - 1))
+ prandom_u32_max(E * XXX_MAKE_SURE_E_IS_POW2)
|
- ((u64)(E) * get_random_u32() >> 32)
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ~PAGE_MASK)
+ prandom_u32_max(PAGE_SIZE)
)
@multi_line@
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
identifier RAND;
expression E;
@@
- RAND = get_random_u32();
... when != RAND
- RAND %= (E);
+ RAND = prandom_u32_max(E);
// Find a potential literal
@literal_mask@
expression LITERAL;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
position p;
@@
((T)get_random_u32()@p & (LITERAL))
// Add one to the literal.
@script:python add_one@
literal << literal_mask.LITERAL;
RESULT;
@@
value = None
if literal.startswith('0x'):
value = int(literal, 16)
elif literal[0] in '123456789':
value = int(literal, 10)
if value is None:
print("I don't know how to handle %s" % (literal))
cocci.include_match(False)
elif value == 2**32 - 1 or value == 2**31 - 1 or value == 2**24 - 1 or value == 2**16 - 1 or value == 2**8 - 1:
print("Skipping 0x%x for cleanup elsewhere" % (value))
cocci.include_match(False)
elif value & (value + 1) != 0:
print("Skipping 0x%x because it's not a power of two minus one" % (value))
cocci.include_match(False)
elif literal.startswith('0x'):
coccinelle.RESULT = cocci.make_expr("0x%x" % (value + 1))
else:
coccinelle.RESULT = cocci.make_expr("%d" % (value + 1))
// Replace the literal mask with the calculated result.
@plus_one@
expression literal_mask.LITERAL;
position literal_mask.p;
expression add_one.RESULT;
identifier FUNC;
@@
- (FUNC()@p & (LITERAL))
+ prandom_u32_max(RESULT)
@collapse_ret@
type T;
identifier VAR;
expression E;
@@
{
- T VAR;
- VAR = (E);
- return VAR;
+ return E;
}
@drop_var@
type T;
identifier VAR;
@@
{
- T VAR;
... when != VAR
}
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: KP Singh <kpsingh@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4 and sbitmap
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> # for drbd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
BUGs like this are still reproducible:
[ 31.509616] list_add corruption. prev->next should be next (ffff8f8644242300), but was ffff8f86493fd300. (prev=ffff8f86493fd300).
[ 31.521544] ------------[ cut here ]------------
[ 31.526248] kernel BUG at lib/list_debug.c:30!
[ 31.530781] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[ 31.535831] CPU: 1 PID: 626 Comm: wpa_supplicant Not tainted 6.0.0+ #7
[ 31.542450] Hardware name: Dell Inc. Inspiron 660s/0478VN , BIOS A07 08/24/2012
[ 31.550484] RIP: 0010:__list_add_valid.cold+0x3a/0x5b
[ 31.555537] Code: f2 4c 89 c1 48 89 fe 48 c7 c7 28 20 69 89 e8 4c e3 fd ff 0f 0b 48 89 d1 4c 89 c6 4c 89 ca 48 c7 c7 d0 1f 69 89 e8 35 e3 fd ff <0f> 0b 4c 89 c1 48 c7 c7 78 1f 69 89 e8 24 e3 fd ff 0f 0b 48 c7 c7
[ 31.574605] RSP: 0018:ffff9f6f00dc3748 EFLAGS: 00010286
[ 31.579990] RAX: 0000000000000075 RBX: ffff8f8644242080 RCX: 0000000000000000
[ 31.587155] RDX: 0000000000000201 RSI: ffffffff8967862d RDI: 00000000ffffffff
[ 31.594482] RBP: ffff8f86493fd2e8 R08: 0000000000000000 R09: 00000000ffffdfff
[ 31.601735] R10: ffff9f6f00dc3608 R11: ffffffff89f46128 R12: ffff8f86493fd300
[ 31.608986] R13: ffff8f86493fd300 R14: ffff8f8644242300 R15: ffff8f8643dd3f2c
[ 31.616151] FS: 00007f3bb9a707c0(0000) GS:ffff8f865a300000(0000) knlGS:0000000000000000
[ 31.624447] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 31.630286] CR2: 00007fe3647d5600 CR3: 00000001125a6002 CR4: 00000000000606e0
[ 31.637539] Call Trace:
[ 31.639936] <TASK>
[ 31.642143] iwl_mvm_mac_wake_tx_queue+0x71/0x90 [iwlmvm]
[ 31.647569] ieee80211_queue_skb+0x4b6/0x720 [mac80211]
...
So, it is necessary to extend the applied solution with commit 14a3aacf51
("iwlwifi: mvm: fix double list_add at iwl_mvm_mac_wake_tx_queue")
to all other cases where the station queues are invalidated and the related
lists are not emptied. Because, otherwise as before, if some new element is
added later to the list in iwl_mvm_mac_wake_tx_queue, it can match with the
old one and produce the same commented BUG.
That is, in order to avoid this problem completely, we must also remove the
related lists for the other cases when station queues are invalidated.
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Reported-by: Petr Stourac <pstourac@redhat.com>
Tested-by: Petr Stourac <pstourac@redhat.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221010081611.145027-1-jtornosm@redhat.com
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
* refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
* support CYW43439 SDIO chipset
* support BCM4378 on Apple platforms
* support CYW89459 PCIe chipset
rtw89
* more work to get rtw8852c supported
* P2P support
* support for enabling and disabling MSDU aggregation via nl80211
mt76
* tx status reporting improvements
ath11k
* cold boot calibration support on WCN6750
* Target Wake Time (TWT) debugfs support for STA interface
* support to connect to a non-transmit MBSSID AP profile
* enable remain-on-channel support on WCN6750
* implement SRAM dump debugfs interface
* enable threaded NAPI on all hardware
* WoW support for WCN6750
* support to provide transmit power from firmware via nl80211
* support to get power save duration for each client
* spectral scan support for 160 MHz
wcn36xx
* add SNR from a received frame as a source of system entropy
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmM3BGYRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuR3Af/XiuMlnDB6flq+M/kQHLWWvHybLw5aCJ7
l3yXhNFWxpBl2hQXtj17JSjVCYQmxbfrgRqhbNhyACO25bpymCb5QctB9X+Y7TwL
250JmuKvQfFx5oJNRfJ67dKTf3raloQYbdEMJNqySgebL+eSfrDskc9vaCLVDmCK
I994fl0Q1wUbJ6fbuIFd07ti8ay6UlSS/iakv4+nEeimabtZWJWlXBWYRpKpikdP
h9z2kPtss6yz6seaQuw6ny+qysYLi11Tp+Cued9XR3dWOOhB2X1tLHH0H02xPw76
9OJZEJHycP2juxjMfAaktHY+VX36GPLsMLUTVusH0h/Fdy3VG8YSAw==
=emmG
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.1
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
- refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
- support CYW43439 SDIO chipset
- support BCM4378 on Apple platforms
- support CYW89459 PCIe chipset
rtw89
- more work to get rtw8852c supported
- P2P support
- support for enabling and disabling MSDU aggregation via nl80211
mt76
- tx status reporting improvements
ath11k
- cold boot calibration support on WCN6750
- Target Wake Time (TWT) debugfs support for STA interface
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- implement SRAM dump debugfs interface
- enable threaded NAPI on all hardware
- WoW support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
wcn36xx
- add SNR from a received frame as a source of system entropy
* tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (231 commits)
wifi: rtl8xxxu: Improve rtl8xxxu_queue_select
wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
wifi: rtl8xxxu: gen2: Enable 40 MHz channel width
wifi: rtw89: 8852b: configure DLE mem
wifi: rtw89: check DLE FIFO size with reserved size
wifi: rtw89: mac: correct register of report IMR
wifi: rtw89: pci: set power cut closed for 8852be
wifi: rtw89: pci: add to do PCI auto calibration
wifi: rtw89: 8852b: implement chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add DMA busy checking bits to chip info
wifi: rtw89: mac: define DMA channel mask to avoid unsupported channels
wifi: rtw89: pci: mask out unsupported TX channels
iwlegacy: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper
ipw2x00: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
wifi: iwlwifi: Track scan_cmd allocation size explicitly
brcmfmac: Remove the call to "dtim_assoc" IOVAR
brcmfmac: increase dcmd maximum buffer size
brcmfmac: Support 89459 pcie
brcmfmac: increase default max WOWL patterns to 16
cw1200: fix incorrect check to determine if no element is found in list
...
====================
Link: https://lore.kernel.org/r/20220930150413.A7984C433D6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for reducing the use of ksize(), explicitly track the
size of scan_cmd allocations. This also allows for noticing if the scan
size changes unexpectedly. Note that using ksize() was already incorrect
here, in the sense that ksize() would not match the actual allocation
size, which would trigger future run-time allocation bounds checking.
(In other words, memset() may know how large scan_cmd was allocated for,
but ksize() will return the upper bounds of the actually allocated memory,
causing a run-time warning about an overflow.)
Cc: Gregory Greenman <gregory.greenman@intel.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Cc: Ilan Peer <ilan.peer@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220923220853.3302056-1-keescook@chromium.org
This notification replaces the WOWLAN_GET_STATUSES command-and-response,
so it's required to parse all the keys in the notification just like
what happened when that command was used.
Move around a few required static functions in order to avoid forward
declarations.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220906161827.ca3fb23cab81.I0a9fe7729af4567b98813bc51bad13ee5512a0ae@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
In recent patches notifications based d3 resume flow was added,
and the resume flow was changed.
Currently, when resuming from d3 during which an assert was thrown,
the resume flow skips the iteration over active interfaces
preventing the sta to reconnect to the ap.
Perform the iteration in case an assert was thrown to fix it.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220906161827.ad888cc6cd91.Ib56e416fce17df089edf76d22896430df5ebe080@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
We have recently enabled resume flow based on notifications.
These notifications are sent by the FW when completing the resume flow.
From IWL_DEVICE_FAMILY_AX210 the resume flow is triggered by the
transport layer on iwl_trans_d3_resume.
On IWL_DEVICE_FAMILY_22000 and earlier we trigger the resume flow by
sending the D0I3 command.
Currently, we are waiting for the notifications before sending the
command, the notifications won't be sent by the FW since there is no
resume trigger to piggyback on.
Send the command before starting the wait flow to fix it.
Signed-off-by: Haim, Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220906161827.5f0f251edf9c.Ia49ab73105af6f52aa7d318f4984edecd3b0671a@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Due to IMR, when host returns from hibernate, commands cannot
be sent as part of the resume flow, and so after ending
d3 the FW needs to send notifications instead of responses.
This notification indicates whether a fw reset is required.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220906161827.898ecba881b2.I13eb69bb5af08b9ac33043647eaed6b8d50e8659@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
The wowlan info notification is quite big.
(~750 bytes without the wake packet itself).
The max FW notification size is ~2K.
There might be cases where the wake packet gets truncated because of
this limit.
Separating the wake packet from the wowlan info notification allows us to
get more data without trimming it.
Note: we currently limit the wake packet to 1600 bytes.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220906161827.06d1e6aecf10.Ib3d6a46ffe71d10cbc69bdb5654e6b14c28df245@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
IMR (Isolated Memory Regions) is a mechanism to protect memory regions
from unwarranted access by agents in the system that should not have access
to that memory.
When IMR is enabled, pages in the DRAM will be located within the IMR
memory space, accessible only by the device.
As a side effect, during S4 (a.k.a hibernate) the IMR memory space
is not retained.
While the DRAM is saved to the disk and restored by the OS upon resume,
the IMR, which is hidden from the OS neither saved upon suspend nor
restored upon resume.
As a consequence of the above, it turned out that commands cannot
be sent as part of the resume flow, and so after ending
d3 the FW needs to use notifications instead of cmd-resp.
The resume flow becomes asynchronous, with a series
of notifications, starting with wowlan_info_notif, through
wowlan_pkt_notif and complete the resume flow by d3_end_notif.
This patch adds the support for wowlan info notification.
The wake packet has been removed from the wowlan info struct
and will be handled in a dedicated notification.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220906161827.3ce8deefd929.Ieba8610e8bb4bec788076371ae38becb4a3d20d5@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
This code is dead, even old FW versions don't use it.
The IWL_D0I3_RESET_REQUIRE flag will be sent by the FW via a notification,
instead of command, the notification handler will be introduced later
in the series.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220906161827.87c82482229a.I70456c38ed8f7beb7d62dd618f58e7dc0a7d33b2@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
There's a bunch of duplicated code in the normal data RX and
the no-data RX paths, refactor that.
Note that we're evidently not implementing the 6 GHz band in
the no-data path correctly, need to fix that in firmware
first. Also, we were setting the NSS differently, keep doing
that, but just override the previous values.
Note also that we used to drop frames with bad rate data, to
simplify that just report rate 0 and continue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220906161827.a81580d5e769.I3ee7a1fe1adf8684c48713dbbdc2cbc60bd24cd1@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
I get a log line like this every 4 seconds when connected to my AP:
[15650.221468] iwlwifi 0000:09:00.0: Got NSS = 4 - trimming to 2
Looking at the code, this seems to be related to a hardware limitation,
and there's nothing to be done. In an effort to keep my dmesg
manageable, downgrade this error to "debug" rather than "info".
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220905172246.105383-1-Jason@zx2c4.com
The A-MSDU data needs to be stored per-link and aggregated into a single
value for the station. Add a new struct ieee_80211_sta_aggregates in
order to store this data and a new function
ieee80211_sta_recalc_aggregates to update the current data for the STA.
Note that in the non MLO case the pointer in ieee80211_sta will directly
reference the data in deflink.agg, which means that recalculation may be
skipped in that case.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SMPS power save mode needs to be per-link rather than being shared
for all links. As such, move it into struct ieee80211_link_sta.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building with Clang we encounter these warnings:
| drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:1108:47: error:
| format specifies type 'unsigned char' but the argument has type 's16'
| (aka 'short') [-Werror,-Wformat] IWL_DEBUG_INFO(mvm, "\tburst index:
| %hhu\n", res->ftm.burst_index);
-
| drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:1111:47: error:
| format specifies type 'unsigned char' but the argument has type 's32'
| (aka 'int') [-Werror,-Wformat] IWL_DEBUG_INFO(mvm, "\trssi spread:
| %hhu\n", res->ftm.rssi_spread);
The previous format specifier `%hhu` describes a u8 but our arguments
are wider than this which means bits are potentially being lost.
Variadic functions (printf-like) undergo default argument promotion.
Documentation/core-api/printk-formats.rst specifically recommends using
the promoted-to-type's format flag.
As per C11 6.3.1.1:
(https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1548.pdf) `If an int
can represent all values of the original type ..., the value is
converted to an int; otherwise, it is converted to an unsigned int.
These are called the integer promotions.` Thus it makes sense to change
`%hhu` to `%d` for both instances of the warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220711222919.2043613-1-justinstitt@google.com
Since mac80211 already has a protected pointer to link_conf,
pass it to the driver to avoid additional RCU locking.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When calling start/stop_ap(), mac80211 already has a protected
link_conf pointer. Pass it to the driver, so it shouldn't
handle RCU protection.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In start_ap and stop_ap mac80211 callbacks pass the link_id
to the drivers.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start making some SMPS related code MLD-aware. This isn't
really done yet, but again cuts down our 'deflink' reliance.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
GCC 12 says:
drivers/net/wireless/intel/iwlwifi/mvm/sta.c:1076:37: warning: array subscript -1 is below array bounds of ‘struct iwl_mvm_tid_data[9]’ [-Warray-bounds]
1076 | if (mvmsta->tid_data[tid].state != IWL_AGG_OFF)
| ~~~~~~~~~~~~~~~~^~~~~
Whatever, tid is a bit from for_each_set_bit(), it's clearly unsigned.
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We used to count the number of ieee80211_vifs in mvm.
This was needed for the legacy PM API, which is no longer
supported. Remove it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220517120045.8c91ae023b15.Ia6145e4930b1d28f3fcedc316b4f177295b00557@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the firmware's life easier and always accept MCAST frames. If
needed, drop them in the driver. We need to filter out MCAST frames
in order not to have false positives in the decryption check. If we
accept MCAST frames before we have the GKT installed, we'll end up
complaining that we can't decrypt the frame.
Implement the same filtering, but in the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220517120045.479956a46317.I21fac7ede9eca85a662671d694872898df884f0b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We track in mvmvif->authorized when the AP STA becomes authorized
and no longer authorized, so we don't need the complex condition
with station lookup. Simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220517120044.41f528383a6b.I1cdf165581b781c53c8e6ac8779a2282b1f67c59@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we're copying the PPAG table into the cmd structure we're failing
if the table doesn't exist in ACPI or is invalid, or if the FW doesn't
support PPAG setting etc.
This is wrong because those are valid scenarios. Fix this by not
failing in those cases.
Fixes: e8e10a37c5 ("iwlwifi: acpi: move ppag code from mvm to fw/acpi")
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220322173828.fa47f369b717.I6a9c65149c2c3c11337f3a802dff22f514a3a436@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
-----BEGIN PGP SIGNATURE-----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=ccps
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
brcmfmac
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
* tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits)
mac80211: Add support to trigger sta disconnect on hardware restart
mac80211: fix potential double free on mesh join
mac80211: correct legacy rates check in ieee80211_calc_rx_airtime
nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation
mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible
mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
rtw89: 8852c: process logic efuse map
rtw89: 8852c: process efuse of phycap
rtw89: support DAV efuse reading operation
rtw89: 8852c: add chip::dle_mem
rtw89: add page_regs to handle v1 chips
rtw89: add chip_info::{h2c,c2h}_reg to support more chips
rtw89: add hci_func_en_addr to support variant generation
rtw89: add power_{on/off}_func
rtw89: read chip version depends on chip ID
rtw89: pci: use a struct to describe all registers address related to DMA channel
rtw89: pci: add V1 of PCI channel address
rtw89: pci: add struct rtw89_pci_info
rtw89: 8852c: add 8852c empty files
MAINTAINERS: add devicetree bindings entry for mt76
...
====================
Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Propagate the value to the user space so it can understand
if the operation failed or not.
Fixes: bfcfdb59b6 ("iwlwifi: mvm: add vendor commands needed for iwlmei")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20220302072715.4885-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some APs misbehave when TWT is used and cause our firmware to crash.
We don't know a reasonable way to detect and work around this problem
in the FW yet. To prevent these crashes, disable TWT in the driver by
stopping to advertise TWT support.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215523
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
[reworded the commit message]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20220301072926.153969-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return -ENODEV instead of success on this error path.
Fixes: dd36a507c8 ("iwlwifi: mvm: look for the first supported channel when add/remove phy ctxt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210816183930.GA2068@kili
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change the comparison from ">" to ">=" to avoid accessing one element
beyond the end of the ->per_mac_stats[] array.
Fixes: 6324c173ff ("iwlwifi: mvm: add support for statistics update version 15")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220106071825.GA5836@kili
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During disassociation we're decreasing the phy's ref count.
If the ref count becomes 0, we're configuring the phy ctxt
to the default channel (the lowest channel which the device
can operate on). Currently we're not checking whether the
the default channel is enabled or not. Fix it by configuring
the phy ctxt to the lowest channel which is enabled.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220210181930.03f281b6a6bc.I5b63d43ec41996d599e6f37ec3f32e878b3e405e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to some issues found in integration, the command now has
the (old) station mask and TID in modify/remove instead of
the BAID, adjust accordingly.
Since we don't use modify yet (and never will with v1 of the
API), just add v1 remove inside the existing union, and use
that, this way we don't have to duplicate everything, only
the remove code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220210181930.bc424f15cc4b.I06d9acae11dc69b2500666f497017a3fd4e2acd5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer firmware versions will support a new queue allocation
command, in order to deal with MLD where multiple stations
are used for a single queue. Add support for the new command.
This requires some refactoring of the queue allocation API,
which now gets
- the station mask instead of the station ID
- the flags without the "enable" flag, since that's no longer
used in the new API
Additionally, this new API now requires that we remove queues
before removing a station, the firmware will no longer do that
internally. Also add support for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220210181930.acbf22ac2b66.I2bf38578c5ca1f7ffb2011a782f772db92fc4965@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add logs in rs_fw_rate_init function. It helps in
verifying TLC Configuration while debuging TLC related bugs.
Update kernel doc for TLC_MNG_CONFIG_CMD with correct version
of struct iwl_tlc_config_cmd.
Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Fixes: ae4c1bb06b ("iwlwifi: rs: add support for TLC config command ver 4")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220210181930.1fd6adfb6f1e.Icc8f5fd517735fcc10db098999ff1272da291298@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The command ID here is always hard-coded to the same, so we
can remove it. In the future we actually need to make this
configurable, but that doesn't need to be on each call, it
can be done through the transport configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220210181930.8b352828f767.Ice4c91d8ea3e207914104e72801b87cd7f409ba7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware will soon stop removing the session protection for us after
association. While this was convenient, it was not symmetric.
Always remove the session protection after association, even for devices
that support the new API.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220205112029.9fd32da15220.Ia88357dcf9f7ec7860f6111e41411868739cc9aa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We are setting the PPE Thresholds in STA_HE_CTXT_CMD according
to HE PHY Capabilities IE. As EHT is introduced, we will have to
set this thresholds according to EHT PHY Capabilities IE if we're
in an EHT connection. Some parts of the code can be used for both
HE and EHT. Put this parts in functions which will be used in the
patch which adds support for EHT PPE.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220205112029.48a508dfffef.If392e44d88f96ebed7fadf827e327194d4bd97b1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With the new ML API, we can't send the BAID removal command to
firmware during hw_restart because it will cause an assertion failure
0x350D because the BAID doesn't exist at that point.
So avoid sending the command if we are performing a hw_restart.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220205112029.7b363457e1aa.Ie4634222e6a33451b88e1042c83e9ea28775bd9f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes RFIm can be deactivated in FW due to internal
errors. In this case, FW will send a notification to the
driver about that. Add a log message in this case since
FW logs are not always available.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220205112029.48d0a1624fec.I8f9271959fc53223fa329ab097b12fd69b498b71@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A scan during active P2P GO operation, i.e., data traffic with
clients, can impact the throughput and latency of such traffic.
Thus, when scan is requested while there is an active P2P GO
and low latency is asserted:
- Ask the FW scan logic to respect the P2P GO activity during the
scheduling of the scan operation to minimize the impact on the
throughput and latency.
- Force scan to perform EBS before starting the scan to reduce the
number of scanned channels.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220205112029.4412036f4889.Ied677fdd31765437e19905787708bd05f62663ba@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Non PSC channels should generally be scanned based on information about
collocated APs obtained during scan on legacy bands, and otherwise
should not be scanned unless specifically requested so (as there are
relatively many non PSC channels, scanning them passively is time consuming
and interferes with regular data traffic).
Thus, modify the scan logic to avoid passively scanning PSC channels
if there is no information about collocated APs and the scan is not
a passive scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220204122220.457da4cc95eb.Ic98472bab5f5475f1e102547644caaae89ce4c4a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, fragmented EBS was set for a channel only if the 'hb_type'
was set to fragmented or balanced scan. However, 'hb_type' is set only
in case of CDB, and thus fragmented EBS is never set for a channel for
non-CDB devices. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220204122220.a6165ac9b9d5.I654eafa62fd647030ae6d4f07f32c96c3171decb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since commit a05829a722 ("cfg80211: avoid holding the RTNL when
calling the driver") we're not only holding the RTNL when going
in and out of suspend, but also the wiphy->mtx. Add that to the
D3 test debugfs in iwlwifi since it's required for various calls
to mac80211.
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220129105618.fcec0204e162.Ib73bf787ab4d83581de20eb89b1f8dbfcaaad0e3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We may not have all the interfaces added to the driver when we get the
THERMAL_DUAL_CHAIN_REQUEST notification from the FW, so instead of
iterating all vifs to update SMPS, iterate only the ones that are
already assigned. The interfaces that were not assigned yet, will be
updated accordingly when we start using them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 2a7ce54ccc ("iwlwifi: mvm: honour firmware SMPS requests")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220129105618.9416aade2ba0.I0b71142f89e3f158aa058a1dfb2517c8c1fa3726@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we enable DCM if the peer supports RX without checking whether
we advertised that we support TX. Fix this by also checking that our TX
side is set.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220129105618.6865266c8a34.If1de7849f25337bb14ba2f27896e9715ae5975df@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to some rearchitecting inside the firmware, a new BAID
allocation command is being introduced. Support it. Note
that with it the firmware no longer returns "no space" but
will crash instead, so check for that before sending the
command to the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220128153014.a89fa3bd9d91.Ibe58c5d9e882dad43aa857aa1c8f54f3358c667b@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most of this change is a continuation of commit 403ea939ea
("iwlwifi: dbg: Mark ucode tlv data as const") propagating the
(const) type qualifier for ucode based tlv data to avoid having
the impression that it is writeable.
The other part of the change preserves the (const) type qualifier
over casts and function calls where it was previously lost.
Both changes are needed to avoid compile time errors on system with
more strict error settings, in this case found with clang on FreeBSD.
Sponsored by: The FreeBSD Foundation
Signed-off-by: Bjoern A. Zeeb <bz@FreeBSD.ORG>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[fix double word in commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220128153014.3230c41312fc.I0032c597984834258d5a79b97052ed83dbe53b80@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to de-const variables simply casting through (void *) is
not enough: "cast from 'const .. *' to 'void *' drops const qualifier".
Cast through (uintptr_t) as well [1] to make this compile on systems
with more strict requirements.
In addition passing const void *data to dma_map_single() also
drops the (const) qualifier. De-constify on variable on assignment
which may be overwritten later. In either case the (void *) cast
to dma_map_single() is not needed (anymore) either.
[1] See __DECONST() in sys/sys/cdefs.h in FreeBSD
Sponsored by: The FreeBSD Foundation
Signed-off-by: Bjoern A. Zeeb <bz@FreeBSD.ORG>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220128153014.eb696eb56bf6.Ide1dd041f9b908c5154a600286a7453750b0704a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The order of arguments for iwl_cmd_id() is confusing, and the
version is always 0 and thus a useless argument. Prefer the
WIDE_ID() macro (which needs to be a macro due to use in switch
cases etc.) over the iwl_cmd_id() function.
Obviously done with spatch:
@@
expression G, C;
@@
-iwl_cmd_id(C, G, 0)
+WIDE_ID(G, C)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220128153014.cc4f9d1a2e9b.Ieb023cd773ea22e819d1ef1c37ae857ecc1a839d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read a new bit defined in ACPI WTAS that allows OEMs to specify whether
TAS is allowed in UHB (6-7GHz) in the USA. This can be used by OEMs
that got certified to use this feature.
Signed-off-by: Ayala Barazani <ayala.barazani@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220128153014.1d2ae1e6bcdb.I177929ed01ed7bf4614ea0f6db2af9e52de13316@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since FW is now in charge of timing the channel switch, there is no need
to send the add/modify/remove time event command to fw with every (e)CSA
element.
However, the driver needs to cancel the channel switch if the CS start
notification arrives and it does not know about an ongoing channel switch.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220128153013.ac3af0ff22c7.Ie87c62047b71b93b12aa80b5dc5391b4798dbe97@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The recent fix for NULL sta in iwl_mvm_get_tx_rate() still has a call
of iwl_mvm_sta_from_mac80211() that may be called with NULL sta.
Although this practically only points to the address and the actual
access doesn't happen due to the conditional evaluation at a later
point, it looks a bit flaky.
This patch drops the temporary variable above and evaluates
iwm_mvm_sta_from_mac80211() directly for avoiding confusions.
Fixes: d599f714b7 ("iwlwifi: mvm: don't crash on invalid rate w/o STA")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220121114024.10454-1-tiwai@suse.de
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We add the fields for parsing extended ADDBA request/respond,
and new max 1K aggregation for limit ADDBA request/respond.
Adjust drivers to use the proper macro, IEEE80211_MAX_AMPDU_BUF ->
IEEE80211_MAX_AMPDU_BUF_HE.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20220214173004.b8b447ce95b7.I0ee2554c94e89abc7a752b0f7cc7fd79c273efea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's currently only one driver that reports CHECKSUM_COMPLETE,
that is iwlwifi. The current hardware there calculates checksum
after the SNAP header, but only RFC 1042 (and some other cases,
but replicating the exact hardware logic for corner cases in the
driver seemed awkward.)
Newer generations of hardware will checksum _including_ the SNAP,
which makes things easier.
To handle that, simply always assume the checksum _includes_ the
SNAP header, which this patch does, requiring to first add it
for older iwlwifi hardware, and then remove it again later on
conversion.
Alternatively, we could have:
1) Always assumed the checksum starts _after_ the SNAP header;
the problem with this is that we'd have to replace the exact
"what is the SNAP" check in iwlwifi that cfg80211 has.
2) Made it configurable with some flag, but that seemed like too
much complexity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.230736e19e0e.I3e6745873585ad943c152fab9e23b5221f17a95f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAR GEO offsets are not supported on 3160 devices. The code was
refactored and caused us to start sending the command anyway, which
causes a FW assertion failure. Fix that only considering this feature
supported on FW API with major version is 17 if the device is not
3160.
Additionally, fix the caller of iwl_mvm_sar_geo_init() so that it
checks for the return value, which it was ignoring.
Reported-by: Len Brown <lenb@kernel.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 78a19d5285 ("iwlwifi: mvm: Read the PPAG and SAR tables at INIT stage")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128144623.96f683a89b42.I14e2985bfd7ddd8a8d83eb1869b800c0e7f30db4@changeid
This feature has been deprecated and should not be used anymore. With
newer firmwares, namely *-67.ucode and above, trying to use it causes an
assertion failure in the FW, similar to this:
[Tue Jan 11 20:05:24 2022] iwlwifi 0000:04:00.0: 0x00001062 | ADVANCED_SYSASSERT
In order to prevent this feature from being used, remove it entirely
and get rid of the Kconfig option that
enables it (IWLWIFI_BCAST_FILTERING).
Fixes: cbaa6aeede ("iwlwifi: bump FW API to 67 for AX devices")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215488
Cc: stable@vger.kernel.org # 5.16.x
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128144623.9241e049f13e.Ia4f282813ca2ddd24c13427823519113f2bbebf2@changeid
iwlmei can trigger a hardware RFKILL when the CSME firmware
does not want the host to touch the device.
But then, iwlmvm reports RFKILL which makes cfg80211 update
iwlmvm about RFKILL. iwlmvm then thinks there is a change in
the _software_ rfkill and it calls rfkill_blocked() to fetch
the RFKILL state. This returns that RFKILL is blocked (because
of iwlmei) and iwlmvm tells iwlmei that _software_ RFKILL is
asserted.
This is a bug of course.
Fix this by checking explicitly the software RFKILL state and
not the overall RFKILL state.
Fixes: 7ce1f2157e ("iwlwifi: mvm: read the rfkill state and feed it to iwlmei")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 7ce1f2157e ("iwlwifi: mvm: read the rfkill state and feed it to iwlmei")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.f293861a3f92.I9553d27df1de6fd5756a43ea5f8b89d06fa1a6f2@changeid
We're checking the FW version of TX_CMD in order to decide whether to
convert rate_n_flags from the old format to the new one. If the API
is smaller or equal to 6 we should convert it. Currently we're
converting if the API version is greater than 6. Fix it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Fixes: dc52fac37c ("iwlwifi: mvm: Support new TX_RSP and COMPRESSED_BA_RES versions")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.a264ac51d106.I228ba1317cdcbfef931c09d280d701fcad9048d2@changeid
When building ARCH=arm allmodconfig:
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c: In function ‘iwl_mvm_ftm_rtt_smoothing’:
./include/asm-generic/div64.h:222:35: error: comparison of distinct pointer types lacks a cast [-Werror]
222 | (void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
| ^~
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:1070:9: note: in expansion of macro ‘do_div’
1070 | do_div(rtt_avg, 100);
| ^~~~~~
do_div() has to be used with an unsigned 64-bit integer dividend but
rtt_avg is a signed 64-bit integer.
div_s64() expects a signed 64-bit integer dividend and signed 32-bit
divisor, which fits this scenario, so use that function here to fix the
warning.
Fixes: 8b0f92549f ("iwlwifi: mvm: fix 32-bit build in FTM")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211227191757.2354329-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmHEgv4RHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt7jQf/W1J8lkaMw6mYnr+inmwKaP11VIk765Sf
4FXZl4xks5rs5zJOs61c/zInNIbu7QVsJzQLmM/bhTB1zoZMRo6ugXXrZ/LPMT1u
X0mul1rC+NLZLlgaimNXRZUXJ2tGUsYYhGoZLHbcILx7XF7/9WtE4h7tLviLdMYk
l42yjjP6s/I/zQHrLQdA9/puGl7g8CItbwaNZg6+PjgbS9NPGATrw9UZdOWjPcl4
JLMRHVgKtdlYL/U/IvsYg6o3Vbo0r+KEI2IMg5fOSpNwqbeQRIN4cZG4TDeRDqD/
k4/ZiFYlNdfVeWmZxHyqX6D3sroIquKglyah34fjzsJ2TbJC1zMvjw==
=VHFz
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
* tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits)
mt76: mt7921: fix a possible race enabling/disabling runtime-pm
wilc1000: Document enable-gpios and reset-gpios properties
wilc1000: Add reset/enable GPIO support to SPI driver
wilc1000: Convert static "chipid" variable to device-local variable
rtw89: 8852a: correct bit definition of dfs_en
rtw88: don't consider deep PS mode when transmitting packet
ath11k: Fix unexpected return buffer manager error for QCA6390
ath11k: add support of firmware logging for WCN6855
ath11k: Fix napi related hang
ath10k: replace strlcpy with strscpy
rtw88: support SAR via kernel common API
rtw88: 8822c: add ieee80211_ops::hw_scan
iwlwifi: mei: wait before mapping the shared area
iwlwifi: mei: clear the ownership when the driver goes down
iwlwifi: yoyo: fix issue with new DBGI_SRAM region read.
iwlwifi: fw: fix some scan kernel-doc
iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
iwlwifi: mvm: remove card state notification code
iwlwifi: mvm: drop too short packets silently
iwlwifi: mvm: fix AUX ROC removal
...
====================
Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d068ca2ae2 ("codel: split into multiple files") moved all
Qdisc-related code to codel_qdisc.h, move the include of pkt_sched.h
as well.
This is similar to the previous commit, although we don't care as
much about incremental builds after pkt_sched.h was touched itself
it is included by net/sch_generic.h which is modified ~20 times
a year.
This decreases the incremental build size after touching pkt_sched.h
from 1592 to 617 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* Support for Time-Aware-SAR (TAS) as read from the BIOS;
* Fix scan timeout issue when 6GHz is enabled;
* Work continues for new HW family Bz;
* Support for Optimized Connectivity Experience (OCE) scan;
* A bunch of FW debugging improvements and fixes;
* Fix one 32-bit compilation issue;
* Some RX changes for new HW family
* Some fixes for 6 GHz scan;
* Fix SAR table fixes with newer platforms;
* Fix early restart crash;
* Small fix in the debugging code;
* Add new Killer device IDs;
* Datapath updates for Bz family continues;
* A couple of important fixes in iwlmei;
* Some other small fixes, clean-ups and improvements.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAmHBrxwACgkQoUecoho8
xfrx7RAAsQDep82tXHDq4il8iGJ0pw/5Whxs4COxRpEpvzMk6fQsiox5+k2CrDT4
K63lusg8ARPJbtWJOMVf6/0UjVrpy3kulzvG208p4J1Rtxs+s0TwbsxFIH4FzUFp
vOlr8ck1GdDicgHNM4jr/vzJu/eUnu+mgOZO0SOK6r3sm8lCAnq7SQjr8cePnCoL
VnRz/27DjpmE4/3cyiMS8c9GwYNDYdzSyb/fQLQ/YkbPzMnSHD1a5OosBZq7B9KL
Db9YOT0tgFSKwPcXxC6rWY5z0R0E8KKXNVfk+Vwj+WmNPhXFPkAVTPHO0wuy6ZZg
NguBk80LOzlXlo5Nr3sYKNtNDBw9IDIP5oZUnBqG5qxsW/rKJNMOPOBgurOpHbY3
+IR+HW9PBjG+j2xlcuVDcXCR/wZxfKk6X7c2PRReBWB8aCRZZb7lfe8KelwtGFkc
fsqPg8ng1Ba7qJ7rm39URRJoi0dQ1+iRmQUJTD3JOsQNmKGvLpMlqmh70VTpRRj/
1Z+zjry3rYUT+hzZA3Qb62Fe62BXX+oLLjFUpnDSVLJhul3vCmlnjT5Yc/gud8M0
jQEkZdCrFzK+1z58E9FmBrdjqzWs5SnatBZnTsyeGnWQbnQguS+Mzfgx3kWOZj30
KfKn0S/97ysG1mdBAZ2yjiD7Tp1rpFrXZMO44KEBEczH6a5rdD4=
=BKW6
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2021-12-21-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
wlwifi patches for v5.17 v2
* Support for Time-Aware-SAR (TAS) as read from the BIOS;
* Fix scan timeout issue when 6GHz is enabled;
* Work continues for new HW family Bz;
* Support for Optimized Connectivity Experience (OCE) scan;
* A bunch of FW debugging improvements and fixes;
* Fix one 32-bit compilation issue;
* Some RX changes for new HW family
* Some fixes for 6 GHz scan;
* Fix SAR table fixes with newer platforms;
* Fix early restart crash;
* Small fix in the debugging code;
* Add new Killer device IDs;
* Datapath updates for Bz family continues;
* A couple of important fixes in iwlmei;
* Some other small fixes, clean-ups and improvements.
* ndo_fill_forward_path support in mac80211, to let
drivers use it
* association comeback notification for userspace,
to be able to react more sensibly to long delays
* support for background radar detection hardware
in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=u1jf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When IWL_UCODE_TLV_CAPA_SESSION_PROT_CMD is set, removing a time event
always tries to cancel session protection. However, AUX ROC does
not use session protection so it was never removed. As a result,
if the driver tries to allocate another AUX ROC event right after
cancelling the first one, it will fail with a warning.
In addition, the time event data passed to iwl_mvm_remove_aux_roc_te()
is incorrect. Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219132536.915e1f69f062.Id837e917f1c2beaca7c1eb33333d622548918a76@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we always return the op_mode with valid pointer in case
getting NVM failed, while it's only relevant for cases that CSME is the
owner of the nic.
Fix this by checking also who's the owner of the nic.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219132536.b1e96021b616.Id0164855f2dd01ecdecf79b239d6ee5974882245@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If OEM isn't in the allowed list, TAS should be disabled in US/CA.
Currently, if the OEM isn't allowed - we're sending the TAS only
if we are not in US or CA.
But this country check is done before we even know the country
(usually the configuration is ZZ in that stage).
So do the following instead:
1. Check if the current OEM is in the allowed list
2. If not - add US and CA to tas_block_list_array
3. Send the TAS table to FW.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Don't use protected ranging negotiation for FTM ranging as responders
that support only FTM ranging don't expect the FTM request to be
protected.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Fixes: 517a5eb9fa ("iwlwifi: mvm: when associated with PMF, use protected NDP ranging negotiation")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219132536.f50ed0e3c6b3.Ibff247ee9d4e6e0a1a2d08a3c8a4bbb37e6829dd@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 6GHz passive scan is performed only once every 50 minutes.
However, in case of suspend/resume, the regulatory information
is reset, so 6GHz channels may become disabled.
Fix it by performing a 6GHz passive scan within 60 seconds after
suspend/resume even if the 50 minutes timeout did not expire yet.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Fixes: e8fe3b41c3 ("iwlwifi: mvm: Add support for 6GHz passive scan")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.6d5c043372cf.I251dd5618a3f0b8febbcca788eb861f1cd6039bc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of a conflict between BIOS version and FW
version of the PPAG table - the values arrive in the FW in the wrong
places. This happens because we're storing the table in different
structures depending on the BIOS version, not on the FW version,
and so the FW doesn't get what it expect to.
Always store the table in a v2 structure (which is a superset
of v1 and v0).
Also store the table in a structured way and in it's own structure,
rather then storing it in the ppag command structure, similarly to
the WRDS, EWRD and WGDS tables.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.793a509da7bd.Ia176746a28b816b5f788cce9a281139735909e2a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The RADA might include in the Rx frame the MIC and CRC bytes.
These bytes should be removed for non monitor interfaces and
should not be passed to mac80211.
Fix the Rx processing to remove the extra bytes on non monitor
cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.098be12c801e.I1d81733d8a75b84c3b20eb6e0d14ab3405ca6a86@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some cases the sta is being removed twice since we do not test the
roc aux running before removing it. Start looking at the bit before
removing the sta.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Fixes: 2c2c3647cd ("iwlwifi: mvm: support ADD_STA_CMD_API_S ver 12")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.d5376ac6bcb0.Ic5f8470ea60c072bde9d1503e5f528b65e301e20@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW API for PER_CHAIN_LIMIT_OFFSET_CMD is misleading. The element
name is table_rev, but it shouldn't actually contain the table
revision number, but whether we should use the South Korea scheme or
not.
Fix the driver so that we only set this value to either 0 or 1. It
will only be 1 (meaning South Korea) if the ACPI WGDS table revision
is 1.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 664c011b76 ("iwlwifi: acpi: support reading and storing WGDS revision 2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.abed3b8119c7.I1fdc2c14577523fcffdfe8fb5902c2d8efde7e09@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't really have much reason to mistrust the hardware
queue number, but if it gets mixed up we still don't want
to access some data out of bounds, so drop such frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.539aecb91247.I6e555a5185bad30d7d1a4659f9c0b99325425f18@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On Bz devices, the hardware checksums including the SNAP header,
starting directly after the MAC header, so we don't need the
extra checks and can just pass the checksum to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.8ef59da4e05e.Ide87c2dc8fa08eae55c013a625f4ece5184b1b63@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For the upcoming Bz devices, we will set NETIF_F_HW_CSUM instead
of NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM. However, we still need
to be able to remove all the checksum bits, so add a mask for the
removal, and keep the old define for the feature advertisement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.f05488ce8b83.I65bb83721498d8433e4ee2b09415eb74ab579445@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case the fw supports OCE scan and one of the OCE feature flags
are set in the scan request, set the corresponding flag in the
firmware scan request.
Note that new firmware that indicates OCE support does not support
the probe deferral and suppression feature (which is optional).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211210110539.3dd63c381839.Id79b39f650103bb9b851e31ed6a0178e81988587@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On a 32-bit build, the division here needs to be done
using do_div(), otherwise the compiler will try to call
a function that doesn't exist, thus failing to build.
Fixes: b68bd2e314 ("iwlwifi: mvm: Add FTM initiator RTT smoothing logic")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219111352.e56cbf614a4d.Ib98004ccd2c7a55fd883a8ea7eebd810f406dec6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With the introduction of 6GHz channels the scan guard timeout should
be adjusted to account for the following extreme case:
- All 6GHz channels are scanned passively: 58 channels.
- The scan is fragmented with the following parameters: 3 fragments,
95 TUs suspend time, 44 TUs maximal out of channel time.
The above would result with scan time of more than 24 seconds. Thus,
set the timeout to 30 seconds.
Cc: stable@vger.kernel.org
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211210090244.3c851b93aef5.I346fa2e1d79220a6770496e773c6f87a2ad9e6c4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new version enables support for EHT mode configurations.
The name of IWL_TLC_HT_BW_NONE_160 change to IWL_TLC_MCS_PER_BW_80
to make the difference from 80 bandwidth (non 160), and the new bandwidth
320 which is also non 160.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211210090244.7d1a57f3df1b.Ibc01dde2b064329ad5f5bcefa83d1998d557cbdb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After some lab experimentation with different DDRs, need
to update the table. Also, arrange it by frequency and not
by DDR type since now the table contains a super-set of all
possible conflicts.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211210090244.6f2fca102739.I8b5e37a00c50b7b51f7d377216dde91e71faffba@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add list of vendors that are allowed to use TAS and check it
against the value provided in the SMBIOS manufacturer field.
Initially add the following approved vendors: HP, Dell, Lenovo and Samsung.
Signed-off-by: Ayala Barazani <ayala.barazani@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211210090244.27fe6abf2e4c.I806e4b47dabddaa8ac27172e7cfa3d719c100e8f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These lines need to be indented one more tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211110080922.GF5176@kili
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This line was indented too far and was a bit confusing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211110080759.GE5176@kili
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If iwl_transt_start_hw() failed, we were returning without calling
wiphy_unlock() and rtnl_unlock(), causing a locking imbalance:
drivers/net/wireless/intel/iwlwifi/mvm/ops.c:686:12: warning: context imbalance in 'iwl_mvm_start_get_nvm' - wrong count at exit
Fix that by adding the unlock calls.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211219090128.42417-2-luca@coelho.fi
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmG8i3cRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZumyAf7BlhO1TUuwhhs9y6fi6KLa/pEOmkx2SRf
9AuEfxxrLPhlzh29Dz4Bn8B+KBG6HFQ1FngSwIAVjLL5pX/1ARBMx9B2TDf9p/Sb
UgkE6WOX29s7LXuC2lDnBnvnKbf5/rdLmZPZCFCv/iKaGAJAYYXYSQjtj5/Fmdkc
PhQNgALWG9a02bfSLk1MlF1lCqt0hsKFQkza29jTa9CKcWYZFK3sTl1spbHAN5yQ
YJMecy+fSxCSuJPZB3elG5os69sz3WGoFY/AYCWoUODNZo18Z4kiAXwurPDIM+GW
3e/lzXe29V1TB36haNe9/C5F2uwoYWGSoWwHcZ62lLpNhJ649wJDbw==
=4wFO
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
* tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (129 commits)
wcn36xx: Implement beacon filtering
wcn36xx: Fix physical location of beacon filter comment
wcn36xx: Fix beacon filter structure definitions
ath11k: Use reserved host DDR addresses from DT for PCI devices
dt: bindings: add new DT entry for ath11k PCI device support
wilc1000: Improve WILC TX performance when power_save is off
wl1251: specify max. IE length
rsi: fix array out of bound
wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"
wilc1000: Rename tx task from "K_TXQ_TASK" to NETDEV-tx
wilc1000: Rename irq handler from "WILC_IRQ" to netdev name
wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi"
wilc1000: Fix spurious "FW not responding" error
wilc1000: Remove misleading USE_SPI_DMA macro
wilc1000: Fix missing newline in error message
wilc1000: Fix copy-and-paste typo in wilc_set_mac_address
rtw89: coex: Update COEX to 5.5.8
rtw89: coex: Cancel PS leaving while C2H comes
rtw89: coex: Update BT counters while receiving report
rtw89: coex: Define LPS state for BTC using
...
====================
Link: https://lore.kernel.org/r/20211217130952.34887C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* A few mei fixes;
* Some improvements in D3;
* Support for new FW API commands;
* Fixes and cleanups in device configurations;
* Support some new FW API command versions;
* Fix WGDS revision 3 reading bug;
* Some firmware debugging improvements;
* Fixes for in device configuration structures;
* Improvements in the session protection code;
* Support SAR GEO Offset Mapping (SGOM) via BIOS;
* Continued work on the new Bz device family;
* Some more firmware debugging improvements;
* Support new FW API version 68;
* Add some new device IDs;
* Some other small fixes, clean-ups and improvements.
-----BEGIN PGP SIGNATURE-----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=tgbw
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2021-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
first set of iwlwifi patches for v5.17
* A few mei fixes;
* Some improvements in D3;
* Support for new FW API commands;
* Fixes and cleanups in device configurations;
* Support some new FW API command versions;
* Fix WGDS revision 3 reading bug;
* Some firmware debugging improvements;
* Fixes for in device configuration structures;
* Improvements in the session protection code;
* Support SAR GEO Offset Mapping (SGOM) via BIOS;
* Continued work on the new Bz device family;
* Some more firmware debugging improvements;
* Support new FW API version 68;
* Add some new device IDs;
* Some other small fixes, clean-ups and improvements.
If we get to the WARN_ONCE(..., "Got a HT rate (...)", ...)
here with a NULL sta, then we crash because mvmsta is bad
and we try to dereference it. Fix that by printing -1 as the
state if no station was given.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6761a71826 ("iwlwifi: mvm: add explicit check for non-data frames in get Tx rate")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20211203140410.1a1541d7dcb5.I606c746e11447fe168cf046376b70b04e278c3b4@changeid
First set of patches for v5.17. The biggest change is the iwlmei
driver for Intel's AMT devices. Also now WCN6855 support in ath11k
should be usable.
Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
rtw88
* add debugfs file to force lowest basic rate
* add quirk to disable PCI ASPM on HP 250 G7 Notebook PC
mwifiex
* add quirk to disable deep sleep with certain hardware revision in
Surface Book 2 devices
iwlwifi
* add iwlmei driver for co-operating with Intel's Active Management
Technology (AMT) devices
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmGvclcRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtK6wgAoOoT83JKMreXlXXhVegqlJbC3HyElF5r
DJlpDDJkJUT9airol2nd0yFfP+5WFyQPrt5shsQmqz43U4jlgfFpFXZIjQufK+gn
VAGvVGfsanRXEFlsVgFZeSZvAEyEyNSggxADC03Ky0xtiCGc89r2o71jD3HA/ZzO
1X8gbKH7YLWj4G/GQkrKsvIAwzoZXT7nwQSdW73M8QVzk4OSNhLBLdiqKYq0yViM
7Ea2Vj27hiyk/RXNUZHy+bKa8vKN5sA91VHJ836aPZBQ4OLotGzF3AgHfgIhIpdr
hI4BVJbngpjQho1EkCnZZuISPes0YQWJB5hK5xpL98yuIL4wyJRfeQ==
=I8Dj
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
First set of patches for v5.17. The biggest change is the iwlmei
driver for Intel's AMT devices. Also now WCN6855 support in ath11k
should be usable.
Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
rtw88
* add debugfs file to force lowest basic rate
* add quirk to disable PCI ASPM on HP 250 G7 Notebook PC
mwifiex
* add quirk to disable deep sleep with certain hardware revision in
Surface Book 2 devices
iwlwifi
* add iwlmei driver for co-operating with Intel's Active Management
Technology (AMT) devices
* tag 'wireless-drivers-next-2021-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (87 commits)
iwlwifi: mei: fix linking when tracing is not enabled
rtlwifi: rtl8192de: Style clean-ups
mwl8k: Use named struct for memcpy() region
intersil: Use struct_group() for memcpy() region
libertas_tf: Use struct_group() for memcpy() region
libertas: Use struct_group() for memcpy() region
wlcore: no need to initialise statics to false
rsi: Fix out-of-bounds read in rsi_read_pkt()
rsi: Fix use-after-free in rsi_rx_done_handler()
brcmfmac: Configure keep-alive packet on suspend
wilc1000: remove '-Wunused-but-set-variable' warning in chip_wakeup()
iwlwifi: mvm: read the rfkill state and feed it to iwlmei
iwlwifi: mvm: add vendor commands needed for iwlmei
iwlwifi: integrate with iwlmei
iwlwifi: mei: add debugfs hooks
iwlwifi: mei: add the driver to allow cooperation with CSME
mei: bus: add client dma interface
mwifiex: Ignore BTCOEX events from the 88W8897 firmware
mwifiex: Ensure the version string from the firmware is 0-terminated
mwifiex: Add quirk to disable deep sleep with certain hardware revision
...
====================
Link: https://lore.kernel.org/r/20211207144211.A9949C341C1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Normally, when we hit an assert, we print out all the
assert data. However, in certain tests, when we trigger
it from debugfs intentionally, that can be useless and
confusing.
Allow writing the string "nolog\n" to the fw_nmi and
fw_restart files suppressing the assert dump as well
as - in the case of fw_restart - the
iwlwifi 0000:00:00.0: FW error in SYNC CMD REPLY_ERROR
message.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204174546.75e29a2ab68d.Id3064feda2ce7a77c116c6d6e71ce5ff447c6e86@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we use 2K RBs, we cannot receive all valid 802.11 frames,
including e.g. long beacons, since up to 2304 bytes are valid
(plus metadata and also encryption overhead etc.). Increase
the RB size to be always 4K to avoid that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204174545.675781ab0da5.I5c653f4c7dd726f8ad40077e4a109b85e7c0cdb1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware is exposing a new system features control command,
define the necessary data structures etc. Rename "soc.h" to
"system.h" since the SoC command is also in the system group
and adding another file for just one more struct seemed like a
waste of files.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204174545.94a120687887.I79acffcf0793ea9e4ddec24b06420961bfb4fe94@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When scheduling a session protection the id is saved but
then it may be cleared when calling iwl_mvm_te_clear_data
(if a previous session protection is currently active).
Fix it by saving the id after calling iwl_mvm_te_clear_data.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204130722.b0743a588d14.I098fef6677d0dab3ef1b6183ed206a10bab01eb2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The main changes are remove the respond from STATISTICS_CMD and sending
it with STATISTICS_NOTIFICATION, and updating for all mac id's and phy
id's in one notification.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204130722.832c7b599202.If192dce8f51ec13005999c3ff96fe09a73cd8f91@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The scan request command is identical in binary format to the previous
scan request command and the only change is now a previously reserved
octet is used to indicate new flags introduced in the command. Align
the code to support the new version and the previous one.
Later patches would add the specific handling for the new
flags.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204130722.392a4af559bc.Ib8f1e3b527453531c10bfd7f4b116d3e257c7f1f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the station is removed we need to remove the session protection
that may be still running.
Note that we need also to remove the session protection upon unassoc in
case the station is kept in the AUTH state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204130722.483977310ca2.If7eba02594f20dabd22d758e1c917fbca54b2ddd@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A new version of this command deprecates the rxchain_info field
but is otherwise the same, so treat it the same way. We already
leave the rxchain_info zeroed since the RLC command is supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.aca5bd78518e.I2f1b4b38899717851ea9f5b6dd23cde27e10387a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's an RLC configuration command in the firmware that's
going to replace the chain information in the PHY context.
Add support for this command, while leaving the PHY context
fields unset when we know the RLC command will be used.
Also add support to send only the RLC configuration command
if only the # of chains used on the PHY context changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.55faa3782bb0.I3f9d0071e680cab513c59b093d0827af99d41c51@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer firmware versions are going to come with a new version
of the wowlan status API, which gives us replay counters for
both GTKs that might still be in use, as well as unifying the
layout of the counters to just be 64-bit quantities.
Extend our code to handle this case and be able to install
replay counters for both keys, if they're sent up from the
firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.73637acafe0b.I33e27712a12fff2816edc0a8abda1759259e20d7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a new version with some addition, we'll need to
do something with the additional data later, but for now
just parse it so we don't fail with the newer firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.f856cb190a4e.I77e3ff5a92b1bcc3e81c1344b046dade0a8b6a24@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the GTK rekeying condition into iwl_mvm_set_key_rx_seq()
so we can modify it in the next patch. In the next firmware
API revision we'll properly get data for both active GTKs and
will have to install it accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.f309942ddd15.Iaa95c602f3a681dd464e10ce2de047aa86fac19c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have a MAC component (which is inside the SoC) and it has several
different HW steps. 3 bits used to be enough but now we need 4-bits
to represent all the different steps.
Properly support 4-bits in the MAC step value by refactoring all the
current handling of the MAC step/dash.
Already from family 8000 and up the dash (bits 0-1) no longer exists
and the step (until 8000 bits 2-3) consists of the dash bits as well.
To do this remove the CSR_HW_REV_STEP and the CSR_HW_REV_DASH
macros, replace them with CSR_HW_REV_STEP_DASH and add hw_rev_step
into the trans struct.
In addition remove the CSR_HW_IF_CONFIG_REG_MSK_MAC_STEP and
CSR_HW_IF_CONFIG_REG_MSK_MAC_DASH macros and create a new macro
combining the 2 (this way we don't need shifting or anything else.)
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Mike Golant <michael.golant@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211207160459.2e81a14d1f80.Ia5287e37fb3439d805336837361f6491f958e465@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.
Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213649
Suggested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reported-by: Maximilian Ernestus <maximilian@ernestus.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.51aea5b79ea4.I88a44798efda16e9fe480fb3e94224931d311b29@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we happen to decide an NSSN queue sync (IWL_MVM_RXQ_NSSN_SYNC)
for some remaining packets that are still on the queue, but just
after we've decided to do a delBA (which causes its own queues
sync with IWL_MVM_RXQ_NOTIF_DEL_BA) we can end up with a sequence
of events like this:
CPU 1 CPU 2
remove BA session with baid N
send IWL_MVM_RXQ_NOTIF_DEL_BA
send IWL_MVM_RXQ_NSSN_SYNC
get IWL_MVM_RXQ_NOTIF_DEL_BA
get IWL_MVM_RXQ_NOTIF_DEL_BA
get IWL_MVM_RXQ_NSSN_SYNC
complete IWL_MVM_RXQ_NOTIF_DEL_BA
remove N from baid_map[]
get IWL_MVM_RXQ_NSSN_SYNC
WARN_ON(!baid_map[N])
Thus, there's a race that leads in hitting the WARN_ON, but more
importantly, it's a race that potentially even results in a new
aggregation session getting assigned to baid N.
To fix this, remove the WARN_ON() in the NSSN_SYNC case, we can't
completely protect against hitting this case, so we shouldn't be
warning. However, guard ourselves against BAID reuse by doing yet
another round of queue synchronization after the entry is removed
from the baid_map, so that it cannot be reused with any in-flight
IWL_MVM_RXQ_NSSN_SYNC messages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083237.44abbbc50f40.I5492600dfe513356555abe2d7df0e2835846e3d8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes the following W=1 kernel build warning:
drivers/net/wireless/intel/iwlwifi/mvm/rfi.c:11: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
[removed the static const fix, since it's already done and
updated the commit message accordingly.]
Link: https://lore.kernel.org/r/20210517050141.61488-7-shenyang39@huawei.com
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Smatch spot a possible NULL pointer dereference. Fix it.
__iwl_mvm_mac_set_key can be called with sta = NULL
Also add a NULL pointer check after memory allocation.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20211130105951.85539-1-emmanuel.grumbach@intel.com
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's easier to use and understand, and to extend for EHT later,
if we use the values here instead of the shifted values.
Unfortunately, we need to add _POS so that we can use it in
places like iwlwifi/mvm where constants are needed.
While at it, fix the typo ("NOMIMAL") which also helps catch any
conflicts.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/r/20211126104817.7c29a05b8eb5.I2ca9faf06e177e3035bec91e2ae53c2f91d41774@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Read the rfkill state upon boot, mac start and mac stop.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-6-emmanuel.grumbach@intel.com
Add the vendor commands that must be used by the network manager
to allow proper operation of iwlmei.
* Send information on the AP CSME is connected to
* Notify the userspace when roaming is forbidden
* Allow the userspace to require ownership
Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
v6: remove the VENDOR_CMDS Kconfig option and make the whole infra
depend on IWLMEI directly
v7: remove // comments
remove an unneeded function
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-5-emmanuel.grumbach@intel.com
iwlmei needs to know about the follwing events:
* Association
* De-association
* Country Code change
* SW Rfkill change
* SAR table changes
iwlmei can take the device away from us, so report the new
rfkill type when this happens.
Advertise the required data from the CSME firmware to the
usersapce: mostly, the AP that the CSME firmware is currently
associated to in case there is an active link protection
session.
Generate the HOST_ASSOC / HOST_DISSASSOC messages.
Don't support WPA1 (non-RSNA) for now.
Don't support shared wep either.
We can then determine the AUTH parameter by checking the AKM.
Feed the cipher from the key installation.
SW Rfkill will be implemented later when cfg80211 will
allow us to read the SW Rfkill state.
Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
v7: Ayala added her signed-off
remove pointless function declaration
fix a bug due to merge conflict in the HOST_ASSOC message
v8: leave a print if we have a SAP connection on a device we do
not support (yet)
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-4-emmanuel.grumbach@intel.com
Fix warnings produced by:
- lockdep_assert_wiphy() in function reg_process_self_managed_hint(),
- wiphy_dereference() in function iwl_mvm_init_fw_regd().
Both function are expected to be called in critical section.
The warnings were discovered when running v5.15 kernel
with debug options enabled:
1)
Hardware name: Google Delbin/Delbin
RIP: 0010:reg_process_self_managed_hint+0x254/0x347 [cfg80211]
...
Call Trace:
regulatory_set_wiphy_regd_sync+0x3d/0xb0
iwl_mvm_init_mcc+0x49d/0x5a2
iwl_op_mode_mvm_start+0x1b58/0x2507
? iwl_mvm_reprobe_wk+0x94/0x94
_iwl_op_mode_start+0x146/0x1a3
iwl_opmode_register+0xda/0x13d
init_module+0x28/0x1000
2)
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c:263 suspicious rcu_dereference_protected() usage!
...
Hardware name: Google Delbin/Delbin, BIOS Google_Delbin
Call Trace:
dump_stack_lvl+0xb1/0xe6
iwl_mvm_init_fw_regd+0x2e7/0x379
iwl_mvm_init_mcc+0x2c6/0x5a2
iwl_op_mode_mvm_start+0x1b58/0x2507
? iwl_mvm_reprobe_wk+0x94/0x94
_iwl_op_mode_start+0x146/0x1a3
iwl_opmode_register+0xda/0x13d
init_module+0x28/0x100
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211110215744.5487-1-lukasz.bartosik@semihalf.com
In some very rare cases the init flow may fail. In many cases, this is
recoverable, so we can retry. Implement a loop to retry two more times
after the first attempt failed.
This can happen in two different situations, namely during probe and
during mac80211 start. For the first case, a simple loop is enough.
For the second case, we need to add a flag to prevent mac80211 from
trying to restart it as well, leaving full control with the driver.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20211110150132.57514296ecab.I52a0411774b700bdc7dedb124d8b59bf99456eb2@changeid
When we receive an association response, a significant amount
of time might have passed since we sent the corresponding
association request (mac80211 will wait up to 500ms for the TX
and then 100ms for the response after ACK was received). But
the time event is touched only when we send the assoc request,
so it might not have much time remaining, more easily causing
the (dreaded)
No beacon heard and the session protection is over already...
message.
Refactor iwl_mvm_mac_mgd_prepare_tx() and split out a new
function iwl_mvm_protect_assoc(), and call it on successful
association to extend the time event to the minimum time if
necessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211024181719.411c174d9e5e.I03c701c2e9e6788f34546e538264763db0ab30ef@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we somehow get disassociated while still waiting for a beacon
during connection, we can end up printing the
No beacon heard and the session protection is over already...
message even if we aren't really quite waiting for it anymore.
Remove the time event, if it's running, when we get disassociated
and don't need to wait for beacons anymore.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211024181719.6192e2363784.Ie9c2bfdc30dcfff2c4dd7c393c79e3ac182840a9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When this code was implemented, there was no official FW API
description yet, so a placeholder name was used (GEO_TX_POWER_LIMIT).
But then the command became actually called
PER_CHAIN_LIMIT_OFFSET_CMD. Rename the command (and change related
comments) to PER_CHAIN_LIMIT_OFFSET_CMD to avoid confusion.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211024181719.672fa727ef75.I6572df5d1e3441a0214993a59985da9a9431f3e5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trying to convert from one firmware data representation to the
next version is getting tedious and error-prone, and doesn't
lend itself well to new APIs being added. Additionally, the
version 11 of the API as defined in the driver doesn't even
exist in the firmware.
Instead of converting to a newer firmware version of the data,
convert to an internal representation. This takes a bit more
space because the TKIP/AES counters etc. must be kept twice,
their representation is different and we don't know which of
the ones it is until later, but this is just a temporary use
of memory, and the code is clearer this way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211024181719.9e71630627f3.Iad975e15338844ca068683f62a51eb1fcb69e608@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a new revision of the WGDS table with more data,
and corresponding firmware API to pass it through. Add
support for both.
Since we now support 4 different versions, make a table
to load them instead of hard-coding it all.
Signed-off-by: Ayala Barazani <ayala.barazani@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211024165252.2f9b8e304f25.If88d2d1309270e659d4845c5b5c22d5e8d8e2caf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To improve chances of hearing beacons and probe responses during
a scan which (based on the scan request parameters) looks like a
roaming scan, enable reception on all chains.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211024165252.f115ad455aca.I5de854fe8ce58c85c21a7adf43526acb29156a08@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the bitmap from the ACPI and pass it to he FW
through LARI_CONFIG_CHANGE_CMD.
This allows OEMs to override channel state to active
as per Geo Location bitmap.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017165728.23d4f2d182c0.I39ac5ff74ac6f2223f393657205eddc1c8e48890@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes driver fails to detect misbehaving AP since we may
miss a few beacons (AP is declared misbehaving only after the second
time CSA counter has a wrong jump).
Move the print to the start of the function to avoid doubts when
analysing this kind of issues.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017165728.8e6b1eb8a436.I5fd6caee968007e91d03b93d6ea84b670ce047e9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set BT coex high priority during the 802.1X handshake to avoid
issues where BT is active enough to kill all the big negotiation
frames that we may need to send (e.g. with a large certificate),
leading to the connection not being established correctly. Give
WiFi priority over BT during this short but critical phase.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017165728.a1825bbba397.I10315577fb41dfcec15c92e8f6785d9655f74c6a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Code tried to avoid setting ACs for PS-poll by an early return.
However as a result the timeouts weren't set as well.
Inactivity timeout of zero means we will always try to go back to
sleep immediately after moving to AM, which doesn't make much sense,
and isn't supported by FW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017165728.dda7f6ba0b22.Ia107bfe496b84e8a2edb33d9f39a5d2b56ed63f7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Evidently, it's possible to hit this issue, so reduce the
noise from it by just having it print a (rate-limited)
message instead. We don't really know yet why we hit it,
but there's no value in having a WARN_ON() here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017162352.8d503387b523.Id2c82d023df5128e553b28c935d30df4d9411917@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When auth/assoc completes, we should remove session protection,
except when association is successful, where we need it until a
beacon is received from the AP.
In particular, in the case of assoc comeback, currently the session
protection event just times out, leading to confusing messages:
wlan0: 42:00:00:00:00:00 rejected association temporarily; comeback duration 1000 TU (1024 ms)
iwlwifi 0000:00:00.0: Not associated and the session protection is over already...
wlan0: Connection to AP 42:00:00:00:00:00 lost
wlan0: associate with 42:00:00:00:00:00 (try 2/3)
mac80211 never does anything on the "Connection ... lost" as it's
not even connected.
Removing the session protection when it's no longer needed removes
those confusing messages and lets the device do other things in the
allocated time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017162352.95e4bebb069b.I635280e5d26c70414ac6eb5d62b46fe4bd942818@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the unused csi parameter from
iwl_mvm_pass_packet_to_mac80211(). It is not used anymore, but was
accidentally left in.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20211017132604.480251-2-luca@coelho.fi
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As part of the new rate_n_flags this two APIs
may use the new rate. Add support for the new rate.
These two APIs were updated in one patch because both of them
are using the same functions which were changed.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017162352.7eb6240b8079.I1e804e70a8ebd23840a9431fc5d2a56ad8d5d1a2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As part of the new rate_n_flags, a new version of this
structures was added in the FW. Add support for this new
version and for the new rate_n_flags in this API.
Both these APIs were updated in one patch since they are
using the same functions.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017162352.a28e7a92f558.I19f72735c674f815c6e7c11cecfad6230b4510ef@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As part of the new rate_n_flags, a new version of
BEACON_TEMPLATE_CMD was added in FW in order to support
the new rate_n_flags.
Add support for the new version.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017162352.b42e67f14293.Ic3f1ed8cb3a31cfaa51174497dd993936b00d398@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As part of the new rate_n_flags, FW added a new version for
LOCATION_RANGE_RSP_NTFY, and it's internal structure -
LOCATION_RANGE_RSP_AP_ETRY_NTFY. Add support for this.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017123741.c5c6c863631e.I4b493f4eeabbfa1dc965ae012b72fc57de7d5f4f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As part of the new rate_n_flags, a new version of tlc_update_notif
was added in FW in order to support the new rate_n_flags.
Add support for the new version, and move the all API to use the
new rate_n_flags only (if FW supports the old one - convert it).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017123741.9fc0cb5d5898.I1f88e02317f79f1be7f792c01236d836045a44b3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As part of the new rate & flags, convert an old format rate to
the new. This is needed if the driver supports the new format
but the FW supports the old one.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017123741.1ea5263dafec.Iadffe7cb26554d4c23c9242eb2ec8326306202a9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use the previously added infrastructure to scrub key material
in firmware dumps:
* in the TX FIFO data, just search for each key that we
know about and override such data
* scrub various commands that we sent to the firmware if
they're present
* in firmware memory, where advertised by firmware TLVs
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017123741.d1514964e6a7.I18f8c2ce8082952af7cfe5f8fe75fe51851b8853@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In firmware dumps, currently all kinds of key material may be
included, e.g. in host commands (if firmware crashes during the
processing of a key-related command) or in the TX FIFO(s) if
we have been using in-TX-command key material.
Additionally, some firmware versions will advertise sections
of their internal data to not dump, due to them containing some
sensitive data.
Add some infrastructure to allow scrubbing this data out, as
dependent on the opmode's idea of what will need to be done.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017123741.360cc8fe55b1.Ie3bd3ece38043969f7e116e61a6ec1197a58d78b@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Consensus seems to be emerging that corporations or groups
shouldn't be listed as module authors, and we will not
maintain this email address any longer. Just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017113927.32109514aad0.I91a7d745f4ab50ee8ef918ece00dda8251541595@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Just like we have default SMPS mode as dynamic in powersave,
we should not enable RX-diversity in powersave, to reduce
power consumption when connected to a non-MIMO AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017113927.fc896bc5cdaa.I1d11da71b8a5cbe921a37058d5f578f1b14a2023@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We should consider the P2P interface type, which isn't in
vif->type due to mac80211's special handling of that. Use
ieee80211_vif_type_p2p() to convert appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017113927.8e992a3beee2.I4231ac8a7ae8f844e35a1ec221baf3e2b676e765@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If resume fails for some reason, we need to set the PM state
back to normal so we're able to send commands during firmware
reset, rather than failing all of them because we're in D3.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 708a39aaca ("iwlwifi: mvm: don't send commands during suspend\resume transition")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20211016114029.7ceb9eaca9f6.If0cbef38c6d07ec1ddce125878a4bdadcb35d2c9@changeid
This code was refactored and the mutex_unlock(&mvm->mutex); was
accidentally deleted.
Fixes: af3aab9ce2 ("iwlwifi: mvm: d3: make key reprogramming iteration optional")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Luca Coelho <luca@coelho.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210831081849.GB9846@kili
These should be >= ARRAY_SIZE() instead of > ARRAY_SIZE() to prevent an
out of bounds write on the next line.
Fixes: 79e561f0f0 ("iwlwifi: mvm: d3: implement RSC command version 5")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Luca Coelho <luca@coelho.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210831081802.GA9846@kili
In __iwl_mvm_remove_time_event() check that 'te_data->vif' is NULL
before dereferencing it.
Fixes: 7b3954a1d6 ("iwlwifi: mvm: Explicitly stop session protection before unbinding")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210907143156.e80e52167d93.Ie2247f43f8acb2cee6dff5b07a3947c79a772835@changeid
Due to a rebase damage, we lost the rtnl_lock() when the patch was
sent out. This causes an RTNL imbalance and failed assertions, due to
missing RTNL protection, for instance:
RTNL: assertion failed at net/wireless/reg.c (4025)
WARNING: CPU: 60 PID: 1720 at net/wireless/reg.c:4025 regulatory_set_wiphy_regd_sync+0x7f/0x90 [cfg80211]
Call Trace:
iwl_mvm_init_mcc+0x170/0x190 [iwlmvm]
iwl_op_mode_mvm_start+0x824/0xa60 [iwlmvm]
iwl_opmode_register+0xd0/0x130 [iwlwifi]
init_module+0x23/0x1000 [iwlmvm]
Fix this by adding the missing rtnl_lock() back to the code.
Fixes: eb09ae93da ("iwlwifi: mvm: load regdomain at INIT stage")
Link: https://lore.kernel.org/lkml/CAHk-=wjB_zBwZ+WR9LOpvgjvaQn=cqryoKigod8QnZs=iYGEhA@mail.gmail.com/
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To check beacon protection had a mismatch of the key ID we
currently use the key ID from the firmware, but firmware
side we want to clean up the API to stop reporting this.
Instead, check the IWL_RX_MPDU_STATUS_KEY_VALID bit that
indicates that the firmware used the correct key, and if
that's set but we get invalid MIC/replay use the key ID
from the frame to look up the key and notify mac80211 of
MIC error or replay. Since both keys must have the same
cipher and thus MIC length, we can use either of them to
look up the MIC length.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.30e665d39b07.I78bf7d304ef5a80cecf5fa1c1fca0b51b956cceb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This version adds the following configuration options:
1. Enable/disable setting the session id in the FTM frame
2. Set the BSS color for the responder
3. Set the minimum and maximum time between measurements for
non trigger based NDP ranging.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.0a10d43f3d7f.Ice4112c1910cf94babd1c2d492a3a3de9f7ee6cb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This version adds the following configuration options:
1. Set the BSS color for NDP ranging
2. Set the minimum and maximum time between measurements for
non trigger based NDP ranging.
3. Terminate the session in case the responder requests LMR feedback.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.9dcd5210b7e5.I76f6977cde852de0f251344e279ad85076eef8d6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When P2P roc is removed, the IWL_MVM_STATUS_NEED_FLUSH_P2P bit is set
to indicate to iwl_mvm_roc_done_wk() that the removed roc is a P2P
one, so it will flush the broadcast station and not the aux station.
However, since setting this bit and scheduling the worker is done
in roc ended flow as well as in case the roc is removed, there is
a race where the worker has already started running (but did not
test this bit yet) and then it is scheduled again. In this case,
the first run of the worker will clear this bit, and thus the second
run will find it already cleared and will try to flush and remove
the aux station by mistake.
Fix it by scheduling the worker only if this bit is not yet set. In
case this bit is already set, the worker is either running or
scheduled, so there is no need to re-schedule it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210819183728.8c147659b331.If5924375e9bfd46214ab8ab81cb9d0f5c82fbcbc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We used to load the regdomain only in the load stage,
this caused the 'iw phy phy0 reg get' command to fail if we
booted a machine with wifi off.
Therefor we should load it in INIT stage already.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.a6077801d7d5.I7d8d5c895bc467efbf81ea055dde366ea01cced1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We used to read the PPAG, WRDS, EWRD, WGDS tables from ACPI
in the load stage only. This prevented vendor commands from
being executed before bringing the interface up. Move reading those tables
to INIT stage.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.ce3b60f0b426.I3643bf00e714aae930880cc7d6cf390b142eaccb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new version of the command has same size and layout as
version 10. It just sends corresponding station id in one
of the reserved fields. It's not used in the driver, so just
be ready to accept version 11.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.0a387598eef1.I3be0bbf603ef95c644218be8a12b329411f11646@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The GEO profiles have been stored in single-dimension arrays and the
access has been done via a single index. We will soon need to support
different revisions of this table, which will make the flat array even
harder to handle. To prepare for that, convert the single-dimension
array to a struct with substructures.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.56f3506411a2.I600ed3708d19f2263a5a8d143f6711d08499bbb0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This definition was only used to pass the size of the tables in the FW
API to the iwl_sar_select_profile() function, but we should actually
pass the definition from the FW API file. We don't have the concept
of tables in the ACPI definition, so we can remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.00b5084be918.I18efb3c45bffacfa9a356c2c8d34e5ffbb3eb423@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- Short SSIDs should always be added for direct SSIDs included
in the scan request. However, this was not done in case that
information for collocated APs was included. Fix this.
- With the above fix, if the FW also supports discovery of hidden
APs over the 6GHz band, also set the corresponding full SSID
information.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.02512b7a1443.Ibb023b09b86179ed049a195f4e32e887c2f4971d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station is removed, the driver-mac80211 station mapping is removed
before the station is actually deleted from the FW. As a result, it is
reasonable that the FW will continue to pass frames although the driver
doesn't have a station for them anymore. Thus change the message
severity level from ERR to DEBUG_DROP.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.a751177743c6.I5607504dade88ba461508643f58390dd661c05ba@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In later firmware we haven't needed the TSC anyway since
we have it already (and firmware image doesn't change),
but the new version adds the ability to send down replay
counters for more than one GTK. Implement that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.28cd065e8c4a.Ic8406a78ee46b07e0ca1b8199522ef08ec6eef53@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that only reprogramming is left in the initial key iteration,
skip it entirely on unified firmware images instead of skipping
only the command sending inside of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.c6f77325c430.I798ce9d757492a9e3d223c1de5d4e62ebbc00b2c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we're sending the KEK/KCK data we also need the GTK and
IGTK type, add a separate key iteration for that so we can
make the configure_key iteration optional later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.c99f86423702.Icf7d4e93be77ea05a80235d01851ad0155593de9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We do a key iteration to program the keys, and while at it
we also collect the data necessary for TKIP. This code has
all kinds of dependencies on the firmware API though, so
take out the TKIP phase 1 key generation and do that in a
separate key iteration only if necessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.80721fc0fd61.I5a8fbba4e3a9606f700ee41c7a4244dd5e2af935@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need for all the complicated conditions here, any
bufferable MMPDUs or MMPDUs for client interfaces are already
coming through the TXQ interface, not iwl_mvm_mac_tx().
Simplify the logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.3939f7c5c43a.I1d5cb5262e31a000023d79acbb897b8db50adf0d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since switching to mac80211 TXQs, we no longer need to
advertise more hardware queues than ACs, since we don't
even set QUEUE_CONTROL anyway, so the vif->hw_queue[]
mapping array won't be used.
All we need (at least for now) is for hw->queues to
indicate that we have enough queues to handle QoS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.80611a3c1ee7.I8a3d2b269421b6d8bada8c12cce3e095e6cfaeed@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When TVQM is enabled (iwl_mvm_has_new_tx_api() is true), then
queue numbers are just sequentially assigned 0, 1, 2, ...
Prior to TVQM, in DQA, there were some statically allocated
queue numbers:
* IWL_MVM_DQA_AUX_QUEUE == 1,
* both IWL_MVM_DQA_INJECT_MONITOR_QUEUE and
IWL_MVM_DQA_P2P_DEVICE_QUEUE == 2, and
* IWL_MVM_DQA_AP_PROBE_RESP_QUEUE == 9.
Now, these values are assigned to the members mvm->aux_queue,
mvm->snif_queue, mvm->probe_queue and mvm->p2p_dev_queue by
default. Normally, this doesn't really matter, and if TVQM is
in fact available we override them to the real values after
allocating a queue for use there.
However, this allocation doesn't always happen. For example,
for mvm->p2p_dev_queue (== 2) it only happens when the P2P
Device interface is started, if any. If it's not started, the
value in mvm->p2p_dev_queue remains 2. This wouldn't really
matter all that much if it weren't for iwl_mvm_is_static_queue()
which checks a queue number against one of those four static
numbers.
Now, if no P2P Device or monitor interface is added then queue
2 may be dynamically allocated, yet alias mvm->p2p_dev_queue or
mvm->snif_queue, and thus iwl_mvm_is_static_queue() erroneously
returns true for it. If it then gets full, all interface queues
are stopped, instead of just backpressuring against the one TXQ
that's really the only affected one.
This clearly can lead to issues, as everything is stopped even
if just a single TXQ filled its corresponding HW queue, if it
happens to have an appropriate number (2 or 9, AUX is always
reassigned.) Due to a mac80211 bug, this also led to a situation
in which the queues remained stopped across a deauthentication
and then attempts to connect to a new AP started failing, but
that's fixed separately.
Fix all of this by simply initializing the queue numbers to
the invalid value until they're used, if TVQM is enabled, and
also setting them back to that value when the queues are later
freed again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2e47e623f9e2.I9b0830dafbb68ef35b7b8f0f46160abec02ac7d0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware SMPS request should only be honoured if the
connection is currently with HE and on 160 MHz, so check
that and then potentially reapply any request if the BW
changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.0cdcac5660da.I9ee7956fd4f48399855d1f97728bc58b36caf112@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When installing a (new) key, set the replay counter so that
after FW restart the firmware has the correct value of the
replay counters.
This doesn't have a large effect - for frames that reach
the driver, it will do a replay check, and when installing
a new key, the counter is normally zero to start with (not
for GTK though, if joining the BSS for the first time).
Since this only affects frames handled entirely by the FW,
and that's restricted to a few unicast management frames,
the only affect here is for those after a firmware restart.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.1cedf2ca7bb6.I2e609c28eaa301436e6740f4f1beca838f69a96a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
EAPOL failure results in deauthentication with various reasons, not
related to AUTH failure specifically, so we just merge AUTH failure
with failed to assoc to AP.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2ff350d85eab.I02c5b5d29c0d5c2e014bd1081b07ed33772ae04d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for discovery of hidden networks on the 6GHz band,
by including the scan request direct SSIDs in the FW scan request
command:
- In case a short SSID matches one of the direct SSIDs in the scan
request command, add the matching SSID in the same offset in the
'direct_ssids' array.
- Otherwise, add the SSID in one of the available slots.
Additionally, as a preparation to handle hidden APs, refactor
iwl_mvm_umac_scan_cfg_channels_v6_6g() the function.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.ffb540a70212.Ia2bb9bc9435b833820bcc7dc30adcedb5a5a9869@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The scan request processing populated the direct SSIDs
in the FW scan request command also for 6GHz scan, which is not
needed and might result in unexpected behavior.
Fix the code to add the direct SSIDs only in case the scan
is not a 6GHz scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.f465937c7bbf.Ic11a1659ddda850c3ec1b1afbe9e2b9577ac1800@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware crashes while we're already shutting down
the system, there isn't much we can do since the shutdown
process is continuing and we wanted to do that. Don't do
a FW restart, with the implied debug collection, in this
case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.43a7351ae6bd.I164d48ce4379accf76ea0637983fd946d52dc6f5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* aggregation handling improvements for some drivers
* hidden AP discovery on 6 GHz and other HE 6 GHz
improvements
* minstrel improvements for no-ack frames
* deferred rate control for TXQs to improve reaction
times
* virtual time-based airtime scheduler
* along with various little cleanups/fixups
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAmDWUHgACgkQB8qZga/f
l8RxXA/+KjkrFUGDHlMTIzS/i03EcB+idLYy+XBWYuO3PN4p/uCCXLzdGfiRKTxp
iCAjYp0ZP01FlN4sOIN+qqrUMoN0e8xqBEY1DFbJELBB1knV4VR0FeBPPcBMUEgE
xAjdZnIsfKO1yU2mrdQVDnkvXr4jHDALePvGwCQe+4KUbwCmVjo6nb534v17Ie3C
MDNnGq395fCvo9NW+Yvzw6s9ZLdhr28bGhSBgBrqmPBx/9vm3b7BA8qO+X6BzAny
87S2x+z40wabBujCGMvw9J5H6OJ0ZLfbT0TumNznqQbCbmwRdSUC+W/cjgRq/aQn
CA3E9T7tofIr1mk9EgcjE8ax91TB/TTX5Nh9Huki25B7rNRBM57VnuEuzmXP5qBS
xgsr60agQHp2ZAGRPBC9msPcPCbvRfdl9ckTAF8/4vI7uEXSyYViX92M0F1FEy60
Mw13B8WeRA4bH22xHpqdXsyl0x2OQHXHlLHfpzmhcUy0i2cQOQMsWbl3g6CJMTq+
/InNSaG+cqrCVse734KJLumRhOq4+MkedYJlqL7uHZJrXlLgQ9Z8ewANjJ/BjTsQ
d8I16XkKPyv8UiJEwHZ6NaHvU48LR8T/r4ym9c/rz0DTWHZyp87QMYa55iwuk4Zo
cW7G3f/N7dMk9fGRxgfIrnNwNUCMsGcBSJeJyr5qT7u8+RW0bRo=
=nFvj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes berg says:
====================
Lots of changes:
* aggregation handling improvements for some drivers
* hidden AP discovery on 6 GHz and other HE 6 GHz
improvements
* minstrel improvements for no-ack frames
* deferred rate control for TXQs to improve reaction
times
* virtual time-based airtime scheduler
* along with various little cleanups/fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have mgd_prepare_tx(), but sometimes drivers may want/need
to take action when the exchange finishes, whether successfully
or not.
Add a notification to the driver on completion, i.e. call the
new method mgd_complete_tx().
To unify the two scenarios, and to add more information, make
both of them take a struct that has the duration (prepare only),
subtype (both) and success (complete only).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.5d94e78f6230.I6dc979606b6f28701b740d7aab725f7853a5a155@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sending nulldata packets is important for sw AP link probing and detecting
4-address mode links. The checks that dropped these packets were apparently
added to work around an iwlwifi firmware bug with multi-TID aggregation.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210619101517.90806-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conceptually, this belongs more into the firmware utils
rather than the mvm opmode, so move the collection and
output there.
Note that this slightly changes the format of the Status
line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210621103449.b82b60d81346.Ide3b688107f6a59c7fc7eb1d8f2002b0a5c1f2d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't fill in phy_data.d1 in no-data RX, and thus we
pretend some data is actually filled in radiotap when it
isn't or has default (zero) values.
Fill in phy_data.d1 appropriately, and while at it also
move the info_type initialization into the initializer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.3d488885f77c.Ib97a2bc57c1e9fb98927dc6f802568db313abe3b@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's been a while that the firmware uses LONG_GROUP by default
and not LEGACY_GROUP.
Until now the firmware wrongly advertise the WOWLAN_GET_STATUS
command's version with LEGACY_GROUP, but it is now being fixed.
In order to support both firmwares, first try to get the version
number of the command with the LONG_GROUP and if the firmware
didn't advertise the command version with LONG_GROUP, try to get
the command version with LEGACY_GROUP.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.cd6f4e421430.Iec07c746c8e65bc267e4750f38e4f74f2010ca45@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These two version updates deprecate the need to set/get the nonqos sequence
counter during suspend/resume flow respectively; NICs supporting this
version maintain this counter internally and don't lose it during the
suspend/resume flow.
Note that this means that for such NICs the NON_QOS_TX_COUNTER_CMD is no
longer ever sent.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.dd25dd667798.I8db9adcdbb133304b58cf417f8698611138c83b4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When operating in AP mode with NICs supporting the AP_LINK_PS hw flag,
mac80211 doesn't need to start/stop queueing tx for connected stations
because the FW already handles that.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.64df994c8fbb.I0fa5cda3a5f893a396eef30a01522422be359e69@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of unbinding, the FW would remove the session protection time
events without sending a notification, so explicitly cancel the
session protection, so future requests for mgd_prepare_tx() would not
assume that the session protection is running.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.7c30f85ed241.Ibc19fdbefca7135f2c4ea83d0aef6b81b5033dcd@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the UNII4 setting from the ACPI table and use it in the
LARI_CONFIG_CHANGE_CMD accordingly.
This setting allows OEMs to enable or disable UNII4, bypassing the FW
defaults.
Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.223090c509c4.If03cb5393607ae494041b6187bcec134d6a1e06d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the session protection ends and the Driver is not
associated or a beacon was not heard, the Driver
prints "No beacons heard...".
That's confusing for the case where not associated.
Change the print when not associated to "Not associated...".
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.41a5a5a894fa.I9eabb76e7a3a7f4abbed8f2ef918f1df8e825726@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware can now request SMPS (due to thermal conditions), add
some code to honour such requests and bubble them up through the
stack, subject to our other SMPS constraints, e.g. from Bluetooth.
Then, if the firmware requests SMPS, then we know that it supports
a small extension to the PHY configuration API where a chain mask
of 0 means "use 1 but pick which one yourself", so in this case we
use that extension.
During firmware restart, we stay in the previous state, and the FW
will send us a notification at startup (only) if the temperature is
below the lower or above the high threshold, to sync the state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.85656b7684b9.I7a661a0758d070a750d3a91874d1a0f5fab9febc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
SMPS requests may differ per interfaces due to e.g. Bluetooth
only interfering on 2.4 GHz, so if that's the case we should,
in the case of multiple PHY contexts, still allow RX diversity
on PHY context that have no interfaces with SMPS requests.
Fix the code to pass through the PHY context in question and
skip interfaces with non-matching PHY context while iterating.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.123c6b05809d.I992e3d1c6a29850d02eeec01712b5b685b963a87@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have a P2P Device active, we attempt to only change the
PHY context it uses when we get a new remain-on-channel, if the
P2P Device is the only user of the PHY context.
This is fine if we're switching within a band, but if we're
switching bands then the switch implies a removal and re-add
of the PHY context, which isn't permitted by the firmware while
it's bound to an interface.
Fix the code to skip the unbind/release/... cycle only if the
band doesn't change (or we have old devices that can switch the
band on the fly as well.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210612142637.e9ac313f70f3.I713b9d109957df7e7d9ed0861d5377ce3f8fccd3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the new BIOS DSM and Pass to FW if to disable\enable
11ax for Russia according to the BIOS key. This is
needed to enable OEMs to control enable/disable 11ax in Russia.
Also add support for future "enable 11ax in country X" features.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210612142637.a705f7cedff8.I580f1021cabcc37e88f5ec5e9a6bbf00aae514b6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas
Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of
a couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał
Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well
as the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of
cleanups and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmCRqDIACgkQqDIjiipP
6E8O2Qf5AQvSVoN9WYRBLo1+a4mkGsJ/wHQMEsOA4FVHft5/QVkRtpMNbSiyq00O
YTpNuoBqiYm/tSTyzK/5Oh+0ucgm/ef4c4dTyPjZYw2GB+3rYNRAXdX/tB6Ggjl/
oUArUCoSQZjOU6Y573B05rcHp1PVM/XL9LgD1uX76tXA1MaGvsyC0cyPRAdOANke
W83BWI0XMhv8B1bZwHVB2Oft5x6HhqWBl3HKbNOmPEMtwkqqBCFAqB0wNEH88ZTf
2hyBjBoZQHdMkJsC0piMvIyAjHZiIjQB47VWz31EvKB3/E28xCqRqPViPq9QbrA5
got0+oDbxI96T024ndXRomc0SSxZnw==
=5THg
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Remove duplicate error message for the amlogic driver (Tang Bin)
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of a
couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well as
the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of cleanups
and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
* tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (55 commits)
thermal/drivers/mtk_thermal: Remove redundant initializations of several variables
thermal/core/power allocator: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Lock the thermal zone while looping over instances
thermal/core/power_allocator: Update once cooling devices when temp is low
thermal/core/power_allocator: Maintain the device statistics from going stale
thermal/core: Create a helper __thermal_cdev_update() without a lock
dt-bindings: thermal: tsens: Document ipq8064 bindings
thermal/drivers/tsens: Add support for ipq8064-tsens
thermal/drivers/tsens: Drop unused define for msm8960
thermal/drivers/tsens: Replace custom 8960 apis with generic apis
thermal/drivers/tsens: Fix bug in sensor enable for msm8960
thermal/drivers/tsens: Use init_common for msm8960
thermal/drivers/tsens: Add VER_0 tsens version
thermal/drivers/tsens: Convert msm8960 to reg_field
thermal/drivers/tsens: Don't hardcode sensor slope
Documentation: driver-api: thermal: Remove thermal_notify_framework from documentation
thermal/core: Remove thermal_notify_framework
iwlwifi: mvm: tt: Replace thermal_notify_framework
dt-bindings: thermal: brcm,ns-thermal: Convert to the json-schema
...
thermal_notify_framework just updates for a single trip point where as
thermal_zone_device_update does other bookkeeping like updating the
temperature of the thermal zone and setting the next trip point etc.
Replace thermal_notify_framework with thermal_zone_device_update as the
later is more thorough.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210122023406.3500424-2-thara.gopinath@linaro.org
It is not very useful to WARN if we can't send a host command
The firmware is likely in a bad situation and the fact that
we didn't send the host command has an impact on the firmware
only, not on the driver. The driver could clean up all its
state.
Don't WARN in this case, but just leave a smaller note.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.0324abc169c8.I4f9b769bc38d68f8ed43f77d2cd75e8f1993e964@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we switch channel, we may miss a few beacons on the
new channel. Don't disconnect if the time event for the
switch ends before we hear the beacons.
Note that this is relevant only for old devices that still
use the TIME_EVENT firmware API for channel switch.
The check that we hear a beacon before the time event
ends was meant to be used for the association time event
and not for the channel switch time event.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.3d710091a0bd.I37a161ffdfb099a10080fbdc3b70a4deb76952e2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We cannot lock a mutex while we're in an RCU critical section. At
the same time, we're accessing data structures that are protected
by the mvm->mutex anyway, so just move the entire locking here to
use only that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.4d27bd36e10e.I1fd8e8fe442c41a5deaa560452b598ed7a60ada5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Power save (PS) should only be enabled when we reach the max phy rate.
Before we reach it (MCS_9) for VHT, we should keep trying to improve the
throughput.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.2a2fb9f9c25e.I7c7bbcfbdc1d35d2c3338778fb397dd5b08ea0e8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
umac_error_table In TLV address was read using mask on MSB
but on the same table in alive message it was without which
caused mismatch in devices with different memory region MSB
Signed-off-by: Roee Goldfiner <roee.h.goldfiner@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.179fee442115.Ib6eabe86cfda0b6044f07c07448c366b6e07e53d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of implementing the DSM evaluation function in the MVM code,
refactor it so it can be generalized and part of the common ACPI
implementation.
Signed-off-by: Harish Mitty <harish.mitty@intel.com>
[reworded subject and commit message]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.a24af3551aac.I8e6bd5eb05f853b6331fa4823750f7ba8ffe46e6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the new BIOS DSM and Pass to FW if to disable\enable
11ax for Ukraine according to the BIOS key. this is
needed to enable OEMs to control enable/disable 11ax in Ukraine
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.055654e7707e.If7eaf9839cd5d59729a235df07e31668b408e740@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for ppag in China by reading revision 2 of the ppag table
from ACPI, and passing the data to the FW.
This is needed to enable OEMs to control ppag enablement
in China.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.69af388d0dce.I8cfddf9e6837bf394b00390181b4b774ded19acd@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When doing scan while 6GHz channels are not enabled, the 6GHz band
is not scanned. Thus, if there are no APs on the 2GHz and 5GHz bands
(that will allow discovery of geographic location etc. that would
allow enabling the 6GHz channels) but there are non collocated APs
on 6GHz PSC channels these would never be discovered.
To overcome this, FW added support for performing passive UHB scan
in case no APs were discovered during scan on the 2GHz and 5GHz
channels.
Add support for enabling such scan when the following conditions are
met:
- 6GHz channels are supported but not enabled by regulatory.
- Station interface is not associated or less than a defined time
interval passed from the last resume or HW reset flows.
- At least 4 channels are included in the scan request
- The scan request includes the widlcard SSID.
- At least 50 minutes passed from the last 6GHz passive scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.7c7bd00e0aeb.Ib226ad57e416b43a710c36a78a617d4243458b99@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we do queue sync, it's confusing that we have the structures
declared in the FW API header files that aren't really firmware,
and the union is also confusing - especially now in the code that
checks the size on the return.
So rework this: change the type of sync and whether to do it in a
synchronous fashion to arguments, and build the data structure in
the function, so we don't need the union.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.f62833fd9893.I612d7ac1c655ec4880329360e15d207698c750bc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We use mvm->queue_sync_state to wait for synchronous queue sync
messages, but if an async one happens inbetween we shouldn't
clear mvm->queue_sync_state after sending the async one, that
can run concurrently (at least from the CPU POV) with another
synchronous queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.d11c9bcdb4aa.I0772171dbaec87433a11513e9586d98b5d920b5f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
"Fully associated" means that we heard a beacon with the DTIM
information and the firmware is configured to track the beacons.
Since the firmware needs to track the beacons for the CSA, we
can't configure the firmware for CSA before it knows when the
beacons are expected otherwise we'd get ASSERT 301D.
If we are required to start CSA before we told the firmware
when the beacons are expected to arrive, just report a
failure and let mac80211 disconnect.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.9adaedeb59e4.Idaad6aaf3f9759d023b8e00b10064915c0db9aa3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When moving to the new channel, we block TX until we hear the
first beacon. if it is not heard, we proceed to disconnect.
Since TX is blocked (without mac80211 being aware of it) the frame
is stuck, resulting with queue hang.
Instead, reenable TX before reporting on the connection loss.
As we are on the new channel, there is no problem with that,
even if the original CSA had quiet mode.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.eb4f2ff1b863.Ib16238106b33d58b2b7688dc6297018b915ecef4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unfortunately, since beacon protection isn't fully available
yet, we didn't notice that there are problems with it and
that the replay detection isn't working correctly. We were
relying only on mac80211, since iwl_mvm_rx_crypto() exits
when !ieee80211_has_protected(), which is of course true for
protected (but not encrypted) management frames.
Fix this to properly detect protected (but not encrypted)
management frames and handle them - we continue to only care
about beacons since for others everything can and will be
checked in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: b1fdc2505a ("iwlwifi: mvm: advertise BIGTK client support if available")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.23c990843369.I09c262a8f6f9852cc8f513cdcb31a7f8f87dd8af@changeid
When The driver in D3 and FW crash happens, trans->system_pm_mode
is not reset to IWL_PLAT_PM_MODE_DISABLED which causes the driver
not to send INIT conmmands and D3 resume fails.
This patch contains the fix for resetting trans->system_pm_mode to
IWL_PLAT_PM_MODE_DISABLED and D3 resume is successful.
Signed-off-by: Ravi Darsi <ravi.darsi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210172142.ad170ad48409.Ifc6b10e8b3f235876af91d0e23e90b462d270eff@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, for all devices and families, failing getting the temp
from the fw is indicated in the log as ERR.
This is too severe for two reasons:
1. The driver has a fall back - and schedules the next temp
read immediately after failing to read temp from the fw.
2. The temp read implementation in the fw is different between
HWs, and on older devices the flow is a-sync and may timeout.
Reducing the print severity from ERR to WARN will allow to
track the issue if it will appear many times, but not frighten users
if it appears once.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210172142.dfd423b2b2ef.Icd576dc3e2e7174d3ed9c1c32f48ea0013699e72@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need the NVM until fairly late in the flow and
since this flow will be split soon, get the NVM later to
unite it with the parts that really need it.
Gather all what needs the NVM into a function.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.bab0e65c4909.I789f3eb577b216ad1688269e036ce9fa4880f532@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The STA_CTXT_HE_NIC_NOT_ACK_ENABLED flag tells the firmware
whether *we* support ack-enabled.
So what should be checked is our *own* capability and not
the *peer's* capability.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.59f44e210096.I8f31968f6f7303255e212d869ca0131becd309aa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Return value of the iwl_mvm_load_nvm_to_nic func is not analyzed. If load
NVM to nic func fails and NVM is not loaded to fw properly, then fw may
behave badly and lead to some strange issue. This commit will analyze
return value and if load NVM to nic has failed, then the error code is
sent to the previous func, which will trigger WRT log collection.
iwl_fw_dbg_error_collect() func collects dump only if tri type is
FW_DBG_TRIGGER_ALIVE_TIMEOUT. But when Load NVM to nic function fails
trig_type is FW_DBG_TRIGGER_DRIVER. This commit also has code changes to
collect dump when trig_type is FW_DBG_TRIGGER_DRIVER.
Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.32998850192a.Ic58d08cb6944ca55e343ff0032c82cfa7821e588@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the firmware support for internal station for auxiliary
activities, there is no need to configure an auxiliary station
as part of SCAN_CFG_CMD. Thus, this configuration was removed
from the corresponding structure.
Align the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.9b8da8408692.I7fe99d73cd67ffc817c2ef6af4c9932ce9fc50b2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
No need to pass the dbgfs_dir just to assign it to mvm.
Assign to mvm and then call iwl_mvm_dbgfs_register.
This is a preparation towards the addition of a delayed
op_mode_start flow.
This will allow to split the op_mode_start flow.
Registration to debugfs must happen after we register to
mac80211 and the registration to mac80211 will soon be
delayed in certain cases. In order not to have to remember
the debugfs_dir in a separate variable, just set it into
the mvm structure so that it can be usable later.
Declare mvm->debugfs_dir in the iwl_mvm structure even when
IWLWIFI_DEBUGFS isn't enabled to simplify the source code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.a92ee491863d.I047923aa3598fbf4fb6fce2cdff75a4969fedd76@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the actions that were taken after the registration can
be taken before the registration to mac80211.
This will help to defer part of the op_mode_mvm_start
function to a later stage in case the device is not
available.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.c03cc5db67c1.Ia928ca34d25a73d959a345ffbe4f1217c3f17394@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
BIOS provides RFI feature enable/disable state via WiFi DSM ACPI
object. By default the feature should be disabled.
The GUID for this feature is different from the one driver currently
uses, so need to provide a set of new definitions.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.242bfe368981.Iaccce1e2fa3986b174d0b08942aa4fbf8bb94a95@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
RF Interference Mitigation is a new feature targeted to handle the
problem of interference between DDR memory and WiFi. The role of
the driver is to configure FW with the table holding a mapping
between problematic channels/bands and the corresponding frequencies.
This patch adds RFI infrastructure and adds two debugfs hooks:
- send RFI configuration command (currently with a default table) which
will reset feature in the FW
- read the table, used by the FW (which can be a subset of the table
that driver sent).
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.2cea55a09bc7.I634b79795abad499ce442631d6672ffef8fc6d41@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The call to iwl_sar_geo_init() was moved to the end of the
iwl_mvm_sar_geo_init() function, after the table revision is assigned
to the FW command. But the revision is only known after
iwl_sar_geo_init() is called, so we were always assigning zero to it.
Fix that by moving the assignment code after the iwl_sar_geo_init()
function is called.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 45acebf8d6 ("iwlwifi: fix sar geo table initialization")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.cef55ef3a065.If96c60f08d24c2262c287168a6f0dbd7cf0f8f5c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some change conflicts apparently cause a confusion between a local
variable being used to send the PPAG command and the introduction of a
union for this command. Most parts of the local command were never
copied from the stored data, so the FW was getting garbage in the
tables instead of getting valid values.
Fix this by completely removing the local and using only the union
that we have stored in fwrt.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f2134f66f4 ("iwlwifi: acpi: support ppag table command v2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.d090e0301023.I7d57f4d7da9a3297734c51cf988199323c76916d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When reading the PPAG table from ACPI, we should store everything in
our fwrt structure, so it can be accessed later. But we had a local
ppag_table variable in the function and were erroneously storing the
enabled/disabled flag in it instead of storing it in the fwrt. Fix
this by removing the local variable and storing everything directly in
fwrt.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f2134f66f4 ("iwlwifi: acpi: support ppag table command v2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.889862e6d393.I8b894c1b2b3fe0ad2fb39bf438273ea47eb5afa4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value we receive from ACPI is a long long unsigned integer but the
values should be treated as signed char. When comparing the received
value with ACPI_PPAG_MIN_LB/HB, we were doing an unsigned comparison,
so the negative value would actually be treated as a very high number.
To solve this issue, assign the value to our table of s8's before
making the comparison, so the value is already converted when we do
so.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.b0ec69f312bc.If77fd9c61a96aa7ef2ac96d935b7efd7df502399@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Check FW notification sizes for robustness;
* Improvements in the NAPI implementation;
* Implement a workaround for CCA-EXT;
* Add new FW API support;
* Fix a CSA bug;
* Implement PHY integration version parsing;
* A bit of refactoring;
* One more CSA bug fix, this time in the AP side;
* Support for new So devices and a bit of reorg;
* Per Platform Antenna Gain (PPAG) fixes and improvements;
* Improvements in the debug framework;
* Some other clean-ups and small fixes.
-----BEGIN PGP SIGNATURE-----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=c570
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
iwlwifi patches intended for v5.12
* Check FW notification sizes for robustness;
* Improvements in the NAPI implementation;
* Implement a workaround for CCA-EXT;
* Add new FW API support;
* Fix a CSA bug;
* Implement PHY integration version parsing;
* A bit of refactoring;
* One more CSA bug fix, this time in the AP side;
* Support for new So devices and a bit of reorg;
* Per Platform Antenna Gain (PPAG) fixes and improvements;
* Improvements in the debug framework;
* Some other clean-ups and small fixes.
# gpg: Signature made Fri 05 Feb 2021 12:04:21 PM EET using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
We should only allow PPAG to be enabled by OEMs that are in the
approved list. In order to do this, we need to compare the system
vendor string retrieved from SMBIOS to a list maintained in the
driver. If the vendor string is not in the list, we don't allow PPAG
to be used.
For now the list is empty, but entries will be added to it
individually, in subsequent patches.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210131201908.c9d35b7d8748.I4e4cf61d8fa6ff91d9b0cab2b1ec9ede4be346f5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When version 2 of the PER_PLATFORM_ANT_GAIN_CMD was implemented, we
started copying the values from the command that we have stored into a
local instance. But we accidentally forgot to copy the enabled flag,
so in practice PPAG is never really enabled. Fix this by copying the
flag from our stored data a we should.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f2134f66f4 ("iwlwifi: acpi: support ppag table command v2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210131201908.24d7bf754ad5.I0e8abc2b8747508b6118242533d68c856ca6dffb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We should only collect debug data after exiting suspend state, that's
why we delete the current place in d3.c file, and add it to fwrt flows
that occur while we can still access the fw and collect debug data.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210131201908.eaf378ed403c.I46fae3ee6da1a4b476515b8ad51ad1c0ea2d8381@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Once the all the stations completed the switch, we need
to clear csa_tx_blocked_vif. This was missing. We also
need to re-enable the broadcast / multicast stations.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.f5b813753bdb.Id58979b678974c3ccf44d8b381c68165ac55a3d3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we abort the scan because of a firmware crash, we
need to cancel the delayed work that monitors the scan
completion. Otherwise it'll kick and try to restart the
firmware yet another time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.a497faa942dd.Ibc155ad36da9de7eb0ddcdd826ddf8dd6607d2ac@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were starting the early time-point too late in non-unified
firmwares. Unlike with unified firmwares, we were starting it only
after reading the NVM, so errors in the NVM read phase were not
logged.
Solve this by moving the time-point to the same place as we do with
unified firmwares, i.e. just before we go into the wait-alive code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.bb6d28ceca01.I770fdf3b9b9fa555fe0935926e32cc3509d980de@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The "supp" variable doesn't need to be unsigned long, only
"tmp" is used with for_each_set_bit(). "supp" should just
be a u16, since that's how it's sent to the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.762e50704a39.I014bc7898f90c734f8e9be2a3efaf9bf8b7db6db@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware has support, then advertise it to the stack and
send the key down. Since we re-check the protection in the host
anyway, we don't really need to do anything on RX except that we
should drop frames that the firmware _knows_ are replay errors,
since beacon filtering might otherwise result in replays being
possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.f5a3d53301b3.I23e84c9bb0b039d9106a07e9d6847776757f9029@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we check the length, we only check that the advertised
data length fits into the data we have, but currently not
that it actually matches correctly.
This should be harmless, but if the first two bytes are zero,
then the iwl_rx_packet_payload_len() ends up negative, and
that might later cause issues if unsigned variables are used,
as this is not something that's normally expected.
Change the validation here to precisely validate the lengths
match, to avoid such issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.5184dfc2a445.I0631d2e4f6ffb93cf06618edb035c45bd6d1d7b9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In roaming flows and during reassociation, its possible that data frames
such as EAPOLs for 4 way handshake/ 802.1x authentication are initially set
to higher MCS rate. Though these are pruned down to a lower legacy rate
before sending to the FW, driver also emits a kernel warning - intended for
non-data frames. Add checks to avoid such warnings for data frames, while
also enhancing the debug data printed.
Signed-off-by: Krishnanand Prabhu <krishnanand.prabhu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.d9ded010c4ce.Ie1d5a33d7175c0bcb35c10b5729748646671da31@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While disconnecting from the AP due to bad channel switch
params (e.g. too long Tx block), do not send the firmware
'CSA abort' before disconnecting. That causes canceling the
immediate quiet and can cause transmitting data before the
disconnection happens.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.b9af359a675f.I996fc7eb3d94e9539f8b117017c428448c42c7ad@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
D3_CONFIG_CMD and D0I3_END_CMD should be the last\first
command upon suspend\resume correspondingly, otherwise,
FW will raise an assert (0x342).
There are firmware notifications that cause the driver to
send a command back to the firmware. If such a notification
is sent to the driver while the the driver prepares the
firmware for D3, operation, what is likely to happen is that
the handling of the notification will try to get the mutex
and will wait unil the driver finished configuring the
firmware for D3. Then the handling notification will get
the mutex and handle the notification which will lead to
the aforementioned ASSERT 342.
To avoid this, we need to prevent any command to be sent to
the firmware between the D3_CONFIG_CMD and the D0I3_END_CMD.
Check this in the utility layer that sends the host commands
and in the transport layer as well.
Flag the D3_CONFIG_CMD and the D0I3_END_CMD commands as
commands that must be sent even if the firmware has already
been configured for D3 operation.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.1935a993b471.I3192c93c030576ca16773c01b009c4d93610d6ea@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we want to stop TX'ing because we are suspending, we
have two options: either we check system_pm_mode or we
check the mvm's status that has a bit for the suspend
flow.
The latter is better because test_bit is atomic. Also
add a call to synchronize_net after we set the bit to
make sure that all the new Tx see the bit before we
actually complete the suspend flow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.243c88781302.I5c0379c5a7e5d49410569e7fcd2fff7a419c6dea@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the new api all the flush in the FW is done before we
get the response and in the response we only get the updated
read pointer and all queued packets don't get anymore rx_tx
per packet to free the queued packet, so driver needs to free
all queued packets on flushed queue at once after flush response.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4bd0eca8c0ef.I1601aad2eb2cc83f6f73b8ca52be57bb9fd626ab@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If there are frequent CCA delays due to the extension channel
as detected by the firmware, and we're on 2.4 GHz, then handle
this by disconnecting (with a reconnect hint).
When we disconnect, we'll also update our capabilities to use
only 20 MHz on the next connection (if it's on 2.4 GHz) as to
avoid the use of the extension channel that has too much noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4de9c363b0b5.I709b7e6f73a7537c53f22d7418927691259de8a8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When restarting firmware with an ongoing scheduled scan, we
don't (and shouldn't) mark it as aborted as mac80211 will be
restarting it, and so no event should go out to userspace.
The appropriate comment regarding this wasn't moved to this
place, so add it.
However, we _do_ need to clean up our internal state, since
mac80211 will restart the scan, and we'll otherwise get to
the WARN_ON() a few lines below for no reason whatsoever.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4ddc9b017268.Ie869b628ae56a5d776eba0e7b7f05f42fc566f2e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For testing features where the firmware may send some
notifications it can often be a lot easier to do that
from a test script. Remove most injection limitations
from debugfs to be able to do this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.9aff3c6b4607.I03b0ae7df094734451445ffcb7f9f0274969f1c0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We shouldn't trust the firmware with the sizes (or contents)
of notifications, accessing too much data could cause page
faults if the data doesn't fit into the allocated space. This
applies more on older NICs where multiple notifications can
be in a single RX buffer.
Add a general framework for checking a minimum size of any
notification in the RX handlers and use it for most. Some RX
handlers were already checking and I've moved the checks,
some more complex checks I left and made them _NO_SIZE for
the RX handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.3e155d5e5f90.I2121fa4ac7cd7eb98970d84b793796646afa3eed@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Second set of fixes for v5.11. Like in last time we again have more
fixes than usual Actually a bit too much for my liking in this state
of the cycle, but due to unrelated challenges I was only able to
submit them now.
We have few important crash fixes, iwlwifi modifying read-only data
being the most reported issue, and also smaller fixes to iwlwifi.
mt76
* fix a clang warning about enum usage
* fix rx buffer refcounting crash
mt7601u
* fix rx buffer refcounting crash
* fix crash when unbplugging the device
iwlwifi
* fix a crash where we were modifying read-only firmware data
* lots of smaller fixes allover the driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJgD96RAAoJEG4XJFUm622bubwH/2TxF5aLNnE49BdgksiorD1M
lr6r1QveG/VQkSVdecYV6wmJ/nzzR46Q3c7Ez3ZBnLpboSDmyK7gKIeGlHSLmMwC
YYt3Fnj1XF/UgPs+daCiF/yxz3v7lsDicl8wKYQgpKU/jDj8dfQ/ntM5p3s0tc5O
JaiWeDGQQRgbyE9g3enqW0vho/6luxI0MIOwcSnCLidsM6oAQowbmtzXDpmwagiR
Xyi0eLzSHSCOmH41VNphDZzlL61C6yCLavNpCvCxv/bElTX7XXynwiw3+i8FiU14
TQabyv0z0yd3pVCYp88TFf9cDe7uQ8MS6NG5CoYP3RXHJ1pDEy3a8yBBc1dp2Tc=
=a+lu
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.11
Second set of fixes for v5.11. Like in last time we again have more
fixes than usual Actually a bit too much for my liking in this state
of the cycle, but due to unrelated challenges I was only able to
submit them now.
We have few important crash fixes, iwlwifi modifying read-only data
being the most reported issue, and also smaller fixes to iwlwifi.
mt76
* fix a clang warning about enum usage
* fix rx buffer refcounting crash
mt7601u
* fix rx buffer refcounting crash
* fix crash when unbplugging the device
iwlwifi
* fix a crash where we were modifying read-only firmware data
* lots of smaller fixes all over the driver
* tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers: (24 commits)
mt7601u: fix kernel crash unplugging the device
iwlwifi: queue: bail out on invalid freeing
iwlwifi: mvm: guard against device removal in reprobe
iwlwifi: Fix IWL_SUBDEVICE_NO_160 macro to use the correct bit.
iwlwifi: mvm: clear IN_D3 after wowlan status cmd
iwlwifi: pcie: add rules to match Qu with Hr2
iwlwifi: mvm: invalidate IDs of internal stations at mvm start
iwlwifi: mvm: fix the return type for DSM functions 1 and 2
iwlwifi: pcie: reschedule in long-running memory reads
iwlwifi: pcie: use jiffies for memory read spin time limit
iwlwifi: pcie: fix context info memory leak
iwlwifi: pcie: add a NULL check in iwl_pcie_txq_unmap
iwlwifi: pcie: set LTR on more devices
iwlwifi: queue: don't crash if txq->entries is NULL
iwlwifi: fix the NMI flow for old devices
iwlwifi: pnvm: don't try to load after failures
iwlwifi: pnvm: don't skip everything when not reloading
iwlwifi: pcie: avoid potential PNVM leaks
iwlwifi: mvm: take mutex for calling iwl_mvm_get_sync_time()
iwlwifi: mvm: skip power command when unbinding vif during CSA
...
====================
Link: https://lore.kernel.org/r/20210126092202.6A367C433CA@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/core/tso.c got recent support for USO, and this broke iwlfifi
because the driver implemented a limited form of GSO.
Providing ->gso_type allows for skb_is_gso_tcp() to provide
a correct result.
Fixes: 3d5b459ba0 ("net: tso: add UDP segmentation support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209913
Link: https://lore.kernel.org/r/20210125150949.619309-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we get into a problem severe enough to attempt a reprobe,
we schedule a worker to do that. However, if the problem gets
more severe and the device is actually destroyed before this
worker has a chance to run, we use a free device. Bump up the
reference count of the device until the worker runs to avoid
this situation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.871f0892e4b2.I94819e11afd68d875f3e242b98bef724b8236f1e@changeid
In D3 resume flow, avoid the following race where sending
packets before updating the sequence number (sequence
number received from the wowlan status command response):
Thread 1:
__iwl_mvm_resume clears IWL_MVM_STATUS_IN_D3 and is cut
by thread 2 before reaching iwl_mvm_query_wakeup_reasons.
Thread 2:
iwl_mvm_mac_itxq_xmit calls iwl_mvm_tx_skb since
IWL_MVM_STATUS_IN_D3 is not set using a wrong sequence number.
Thread 1:
__iwl_mvm_resume continues and calls iwl_mvm_query_wakeup_reasons
updating the sequence number received from the firmware.
The next packet that will be sent now will cause sysassert 0x1096.
Fix the bug by moving 'clear IWL_MVM_STATUS_IN_D3' to after
sending the wowlan status command and updating the sequence
number.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.fe927ec939c6.I103d3321fb55da7e6c6c51582cfadf94eb8b6c58@changeid
Having sta_id not set for aux_sta and snif_sta can potentially lead to a
hard to debug issue in case remove station is called without an add. In
this case sta_id 0, an unrelated regular station, will be removed.
In fact, we do have a FW assert that occures rarely and from the debug
data analysis it looks like sta_id 0 is removed by mistake, though it's
hard to pinpoint the exact flow. The WARN_ON in this patch should help
to find it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.5dc6dd9b22d5.I2add1b5ad24d0d0a221de79d439c09f88fcaf15d@changeid
The return type value of functions 1 and 2 were considered to be an
integer inside a buffer, but they can also be only an integer, without
the buffer. Fix the code in iwl_acpi_get_dsm_u8() to handle it as a
single integer value, as well as packed inside a buffer.
Signed-off-by: Matt Chen <matt.chen@intel.com>
Fixes: 9db93491f2 ("iwlwifi: acpi: support device specific method (DSM)")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.5757092adcd6.Ic24524627b899c9a01af38107a62a626bdf5ae3a@changeid
In the new CSA flow, we remain associated during CSA, but
still do a unbind-bind to the vif. However, sending the power
command right after when vif is unbound but still associated
causes FW to assert (0x3400) since it cannot tell the LMAC id.
Just skip this command, we will send it again in a bit, when
assigning the new context.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.64a2254ac5c3.Iaa3a9050bf3d7c9cd5beaf561e932e6defc12ec3@changeid
Also add documentation for 'mvm'.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:400: warning: cannot understand function prototype: 'const u16 expected_tpt_legacy[IWL_RATE_COUNT] = '
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'mvm' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'tbl' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'scale_index' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'attempts' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'successes' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'window' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2677: warning: duplicate section name 'NOTE'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'mvm' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'sta' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'lq_sta' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'band' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:3761: warning: Function parameter or member 'mvm' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:3761: warning: Function parameter or member 'lq_sta' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:4213: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_tx_protection'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-3-lee.jones@linaro.org
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly using the fallthrough pseudo-keyword as a
replacement for a number of "fall through" markings.
Notice that Clang doesn't recognize "fall through" comments as
implicit fall-through.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201117135053.GA13248@embeddedor
When waiting for a notification and then processing it,
we also need to check the size of the data before we use
it. Most places do that already, but fix the remaining
ones to do it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.b29573bcba39.I4b7e72824d06dc0719a40021d933e29edfc14713@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The range response notification has several versions. Check the
notification size according to the expected notification version.
Notifications with incorrect size will be ignored.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.ee57c3214d05.I810d7de33fb08001ef1a2e24714d5b68932e088e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Previously, we added checks that the contained MPDU size is long
enough, but really we should also check that the notification
itself fits into the data. Add some checks for that.
Also add unlikely() annotations on the previously added checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.51cc04cf1e3e.I7bfd6809f8f5feb75f79397646e6656e95688a0e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the channel switch delay that we would incur after the channel
switch actually happens is longer than the quiet time we're willing
to tolerate, disconnect as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.3bc3449922da.Ib0255deb67b2fc21317e274adcacb545bb1dc669@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some races in the hardware that can possibly lead to
a bus lockup later during a restart when we manage to kill the
firmware at a bad time (while it's accessing the bus).
To work around this, add support for a new handshake between
firmware and driver to ensure that the firmware is in a well-
known state before we kill it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.7756fcc9865c.I13de65e0ffcb4186dd4c1a465f66df2e98c9a947@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a channel switch with a very long quiet period, we schedule
a work to disconnect after a while. This work runs in background. In the
meanwhile, we keep getting beacons and sending FW modify command for each.
This has a potential race, where we modify the CSA after we aborted it.
Protect the flow by setting csa_failed to true in case we abort, and check
it before sending the modify command.
This required a modification to the way we treat csa_failed in
iwl_mvm_post_channel_switch:
1. The variable isn't being reset anymore, so we can still look at it in
iwl_mvm_channel_switch_rx_beacon. This is fine, since we reset it when
starting a new CSA.
2. There is no more early return in case of csa_failed. This is fine,
since before this patch csa_failed was set only for GO, and for GO the
function is only resetting the power settings, which we want to restore
even in case of failure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.b023856bdf39.I4ed0149e0018fe5e1ae3c2a1cbc614954016063f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We send some data to the firmware and expect to get it back,
but we shouldn't really trust the firmware on this. Check the
size of all the data we send down to avoid using bad or just
uninitialized data when the firmware doesn't respond right.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.a5a8173f16c7.I4fa68bb2b1c7dcc52ddd381c4042722d27c4a34d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We keep the scan status per UID in scan_uid_status field when the
iwl_mvm_build_scan_cmd() function is called. If we error out after
this, e.g. due to FW restart being in progress, we're not cleaning
up properly, and can run into warnings later.
Clean up internal variables when starting fails after calling the
iwl_mvm_build_scan_cmd() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.970421a2f753.Id62b2da8a0ccccbb114407db82ca485d07749d39@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We're currently doing accounting on the queue sync with an
atomic variable that counts down the number of remaining
notifications that we still need.
As we've been hitting issues in this area, modify this to
track a bitmap of queues, not just the number of queues,
and print out the remaining bitmap in the warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.0a3fa177cd6b.I7c69ff999419368266279ec27dd618eb450908b3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The argument type to iwl_mvm_notify_rx_queue() is currently just
a u8 *, but that's misleading because we actually need the inner
data to be of type struct iwl_mvm_internal_rxq_notif, because we
interpret it when we get it back from the device (to check the
sync bool and possibly the cookie.)
Therefore, clear up any potential confusion and require that the
data passed is of type struct iwl_mvm_internal_rxq_notif *.
Also, while at it, rename the "count" to "notif_size" as "count"
doesn't really clearly say what it's counting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.d28e14682bdc.I9ac366aa97db045be4daa4ba263267a3ac6a6a2f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MPDU contained in a notification shouldn't be larger than the
notification size itself is, validate this.
Reported-by: Haggai Abramovsky <haggai.abramovsky@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.7c721ad37014.Id5746874ecfa208b60baa62691b2d9dc5dd4d89c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Similarly to what I did to iwl_run_init_mvm_ucode, there is no
need to pass the read_nvm parameter. Either we have an NVM
and we don't need to read it, or we don't and we need to read it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.1b764faecfee.I2da0ada577fc16268125a4a15b5e725c18c643ee@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Curretly we only mark HW error state "after" trying to collect HW data,
but if any HW error happens while colleting HW data we go into endless
loop. avoid this by setting HW error state "before" collecting HW data.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.4c7e5a87da15.Ic35b2f28ff08f7ac23143c80f224d52eb97a0454@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support to the 6GHz band (aka. Ultra High Band or UHB). This
allows us to scan and connect to channels in that band, including all
the relevant features, such as preferred scan channels, colocated
channels etc.
Co-developed-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Co-developed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Co-developed-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Co-developed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Co-developed-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com>
Signed-off-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com>
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Co-developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201210000657.0fdbfc3d7352.Idb648536faf21716e2ab2c6d6890d3e49f719cd3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This command should be used only when there's a real client station.
Currently it works, but since soon the driver will stop actually having
an auxiliary station by default, and this command requires _some_ valid
station, it needs to be removed from this flow.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.81b2acfe292b.I8c7372e6f72279e22966a2d0a9066521f9d2f1a0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyTQyAAoJEG4XJFUm622bCdcIAIyVnqdW7pnoDmWIyQmAEnD9
vGARkzghPHXnufpOzohyDdxT12X9klhrxSVIgzEgH1/pl3i1PpnF6KXyGFCC44Lw
wrLXhQygPzmIW1IZtJJE3G72WExXoRjWx6LD1I7C7oEIduqFixXADmK2tKzFp795
Jxum+sOeT6+Dk1OvO/fIroBHX73mRE9zAuiTIMpt2G1j8uXs9QVfcTbTrUshLASN
0sX9J6JutltBuM4G7+bFpVzKnLnlQ7ebUaF6nvTCQsgHWZwkS7yAubSWX9sFohbR
UXgQHNE83s/esOg7nBxAfqTKP8mbxsobmxZtxE5GR5vFY5FJDxqP9Zc2KzPp39w=
=CbX/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During CSA, we briefly nullify the phy context, in __iwl_mvm_unassign_vif_chanctx.
In case we have a FW assert right after it, it remains NULL though.
We end up running into endless loop due to mac80211 trying repeatedly to
move us to ASSOC state, and we keep returning -EINVAL. Later down the road
we hit a kernel panic.
Detect and avoid this endless loop.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d64de2c17bff.Iedd0d2afa20a2aacba5259a5cae31cb3a119a4eb@changeid
We use mvm->queue_sync_state to wait for synchronous queue sync
messages, but if an async one happens inbetween we shouldn't
clear mvm->queue_sync_state after sending the async one, that
can run concurrently (at least from the CPU POV) with another
synchronous queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.51a3148f2c14.I0772171dbaec87433a11513e9586d98b5d920b5f@changeid
We need to feed the configuration id to remove session protection
properly.
Remember the conf_id when we add the session protection so that we
can give it back when we want to remove the session protection.
While at it, slightly improve the kernel doc for the conf_id
of the notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.3642f730333d.I01a98ecde62096d00d171cf34ad775bf80cb0277@changeid
The ROC that runs on the AUX ROC (meaning an ROC on the STA vif),
was added with the HOT_SPOT_CMD firmware command and must be
cancelled with that same command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.a317376154da.I44fa3637373ba4bd421cdff2cabc761bffc0735f@changeid
Currently, our max tpt is limited to max HT A-MPDU for LB,
and max VHT A-MPDU for HB. Configure HE exponent value correctly to
achieve HE max A-MPDU, both on LB and HB.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.4486852ebb56.I9eb0d028e31f183597fb90120e7d4ca87e0dd6cb@changeid
When adding support for version 3 of the GEO_TX_POWER_LIMIT command,
the table argument of iwl_sar_geo_init was changed from a pointer a 1d
array of now-removed iwl_per_chain_offset_group_v1 to a pointer to a 2d
array of iwl_per_chain_offset (iwl_per_chain_offset_group_v1 was a
struct containing 2 copies of iwl_per_chain_offset).
So even for version 2 where the second dimension is of length 2, which
means that the underlying memory layout of the array didn't change, this
requires a small change in the way we loop over it, and this was missed.
Additionally, for the case of version 3 where the second dimension is now
3, in order to fill the first two elements of each row correctly (lb and
hb), iwl_sar_geo_init must get the true number of bands supported.
But because we don't yet store any values for the 3rd (uhb) band, skip
that band.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.73605b6e0548.Id0ec98333277ff9e017e3938ae413b34acc68947@changeid
iwl_mvm_wowlan_program_keys is now setting data directly in
the KEK_KCK command, and the memset is clearing this later,
causing the data to be incomplete.
Just remove the memory clearing, the structure is local and
cleared in the declaration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.0f355b4578c5.Ifbb76a2814925f215a2c889c1792d46d5bd66ab8@changeid
We introduced a new flow to remove an on-going CSA but we
assumed the firwmare understands the
CHANNEL_SWITCH_TIME_EVENT_CMD. This is not true for 7265 and down.
Don't send this command for those devices, but rather use the older
command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.2574e3e47927.Ic0c56411da1096e9a45ee5c3383edf777c5baca0@changeid
ADD_STA_CMD_API_S ver 12 was added in order to properly support
auxiliary activities in CDB NICs. In the new version we don't need
to allocate an aux station at initialization, instead we add an
aux station only when an auxiliary activity that requires a dedicated Tx
queue is needed. For now the only case we need this kind of activity is
when using hot spot 2.0
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.700e6e2e3077.Icdd807b6a3ad3fed806449ea0a13f856aa20e632@changeid
As part of changes made to properly support auxiliary activities in CDB
NICs, an aux sta will be added when using hot spot 2.0 and will need
to be removed when roc flow is done.
In order to do so, prepare the roc_done_wk to work synchronously as the
rm_aux_sta is a SYNC command.
Since now all of th iwl_mvm_flush_sta function are using it sync,
removed the flag argument from the function.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.71b441c8b682.Ia1d216cb680308b91d6da9f73e23ae9f4baac79f@changeid
The FW relies on the re-enablement of the TX in order to know
it can exit quiet mode. Currently in case of CSA with quiet mode,
the quiet mode is never cancelled, resulting in a complete traffic
hang.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.fee389c83ded.I09550fdadb61f899242d7e7b7578672372e2b7fe@changeid
If we have only a single RX queue, such as when MSI-X is not
available, we should not send the RFH_QUEUEU_CONFIG_CMD, because our
only queue is the same as the command queue and will be configured as
part of the context info. Our code was actually trying to send the
command with 0 queues, which caused UMAC assert 0x1D04.
Fix that by not sending the command when we have a single queue.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.c35eeb3299f8.I08f79a6ebe150a7d180b7005b24504bfdba6d8b5@changeid
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1379: warning: Function parameter or member 'rate_n_flags' not described in 'iwl_mvm_hwrate_to_tx_status'
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1379: warning: Function parameter or member 'info' not described in 'iwl_mvm_hwrate_to_tx_status'
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1431: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_get_scd_ssn'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-14-lee.jones@linaro.org
Fix misnamed, and missing descriptions likely due to doc-rot.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'lq' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Excess function parameter 'sync' description in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'vif' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'smps_request' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Excess function parameter 'smps_requests' description in 'iwl_mvm_update_smps'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-11-lee.jones@linaro.org
Looks as if it's never been used.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/ops.c:466:36: warning: ‘iwl_mvm_debug_names’ defined but not used [-Wunused-const-variable=]
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-9-lee.jones@linaro.org
Add support for the new version of the alive notification, which
includes the SKU ID. We don't use the SKU ID yet, so we can just
handle the new notification as if it were version 4.
While at it, clean up a bit and rename the command and structure names
in the comments so that they are aligned with the ones used in the FW.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.6024b149e9e2.Ifcadb506e994ec352e9ce54399719926bc1bb7ee@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The scan request may specify the request scan dwell time.
However, this value may not always be optimal (e.g. short dwell
time for a passive channel). This may happen in a scan request
as a result of beacon report request, in which the AP may request
an active scan, thus setting a short dwell time, but the station
will perform a passive scan due to regulatory.
Ignore the scan duration parameter and always use the internal
scan dwell time which should be optimal.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.6e1d2b8b4489.I9584bb40d44bf31131f57fdd32d5e8848d4fbdd8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware is being updated to report version 11 of this
response in order to include BIGTK material. Parse it, but
for now keep the existing behaviour of disconnecting on any
rekeying with even IGTK presence, need to fix that before
BIGTK can be supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.b7098f097a5c.I4ae1c5b2186b0e04702233a7a7068d69cfd3361a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some bits declared here that simply don't exist
in the firmware, and some are missing (e.g. the key) from
what the firmware has. Align this and move all the fields
into a single one for this status word, which makes this a
bit easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.0ba403d72e7c.I5fa3aa0538f3fbf8c3885b27a1204b5b0464c20a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We are printing the same thing twice, "Enabling TXQ #%d". Previously
the second print was including more information, but now it only
prints the queue number, which is already in the first print. Remove
the redundant one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.1c22d1bc0a88.I24e57317bdddc6c72f69725e1d95683a935e893d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The API added the ability to send for CDB nic what LMAC ID
the cmd belongs to.
Also driver always set apply_time to zero so no need to pass it as
a param and anyway in new API it's removed for no use.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.fa11d1f523b6.Id105899da82c2b08ee62b57133c4ff72bfd0bb80@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New API for temperature measurement (DTS_MEASUREMENT_TRIGGER)
involves getting an immediate response from FW, and not waiting
for a notification like in previous APIs. Support new API while
keeping backwards compatibility.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.b4893554d8e7.Ia4d7f389d4ac3256fcfe3ce6144e924dd6dbf6eb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add an option for adding a PASN responder, specifying the HLTK and
TK (if not associated). When a receiving a range request for a
PASN responder, the driver will ask for a secured measurement with
the specified HLTK and TK.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.28c5f5266000.I2d58b72ff92c47ac33a6aacc27fbf3790b6dfc51@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For secure ranging with an associated station, the driver only needs
to set the HLTK. There is no need to add an internal station for PMF
since the FW will use the existing station which already has the TK
installed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.fcebaa5c9bc8.Ic584cc47fee717d0bdb43965798dbdf45d89910a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The overcome instabilities in the RTT results add smoothing logic
to the reported results. In short, the smoothing logic tracks the
RTT average of each responder for a period of time, and in case
a new RTT results is found to be a spur, the tracked RTT average
is reported instead of the current RTT measurement.
Smooth logic debug configuration using iwl-dbg-cfg.ini:
- MVM_FTM_INITIATOR_ENABLE_SMOOTH: Set to 1 to enable smoothing logic
(default=0).
- MVM_FTM_INITIATOR_SMOOTH_ALPHA: A value between 0 - 100, defining
the weight of the current RTT results vs. the RTT average tracked
based on the previous results. A value of 100 means use only the
current RTT results.
- MVM_FTM_INITIATOR_SMOOTH_AGE_SEC: The maximal time in seconds in which
the RTT average tracked based on previous results is considered valid.
- MVM_FTM_INITIATOR_SMOOTH_UNDERSHOOT: if the current RTT is positive
and below the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
- MVM_FTM_INITIATOR_SMOOTH_OVERSHOOT: if the current RTT is positive
and above the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.48a9cec2081b.Iaec1e29f738232adfe9e2ea8e9eb9b6ff0323ae1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Version 11 of the range request command adds support for setting
the PN for secure ranging. For now, this is not yet supported.
The same functions that are used for version 9 and 10 are also
used for version 11 as the common part is the same.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.6f9ed4140e8c.I046e0d9f6dfaafda9794e5eb2ee1f02fcad2851a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For new APIs this avoids checking every return if it's
IWL_FW_CMD_VER_UNKNOWN (99) or it's lower than the new API value
Done with spatch:
-iwl_fw_lookup_cmd_ver(E1, E2, E3)
+iwl_fw_lookup_cmd_ver(E1, E2, E3, IWL_FW_CMD_VER_UNKNOWN)
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.70bec6eb8008.I6ea78553801d33f7ed10fcd2e4be4ba781fe469a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for the new version of the GEO_TX_POWER_LIMIT command.
This new version includes UHB values in the table, but for now, since
we don't have the ACPI values yet, we support the API, but don't set
the extra values.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.3700197ed1ed.Ia53fb9c4b5033683fd426d51a0ddc46fb444c805@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the version number to the iwl_geo_tx_power_profile_cmd structs and
move the union into a common place. Additionally, reuse the code that
sets elements that are at the same place in the struct across
different versions.
While at it remove an unused variable, add a comment and move the v2
specific element setting to inside the if statement. Additionally,
invert the if for slightly more readability.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.23ec241f16cd.I8cd21fc5a2498e820b50e1f49a4cbfe545afe30e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new version of the command can support more subbands and CDB, so
it can contain more data than earlier versions. Implement support for
the new version of the command, even though we don't have more data to
write to it yet.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.d709a8f17d1d.I9fa54883667c72dabf6d813c70be77538d9af38d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Create a common structure to contain all different versions of the
tx_power_cmd instead of making a union of the different structs
everywhere we need them. Also move the common part of these structs
into a separate structure (instead of reusing v3) and leave the
per_chain_restriction part out of the common part, because this will
change in version 6 of the command (which will be added soon).
While at it, rename per_chain_restriction to per_chain to shorten it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.4f0bea9fe077.Ib3b540a8288af32d6fa213448e13f82763f85bc9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On newer hardware, we have the full checksum, so use it to report
CHECKSUM_COMPLETE and avoid the protocol specific hardware parsing.
Note that the hardware already parses/removes the SNAP header, so
we actually literally get what we need to report to the stack, as
we're expected to checksum everything after the L2 header (which
is translated/added by mac80211).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.869e829c815d.I70f374865b0acafc675a8d7959912eeaeb595acf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we have the same info in two variables,
If umac_error_event_table is 0, we know that UMAC log is not supported,
so we don't need the support_umac_log field.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.299959eeb47b.Ie1f3eecc06e3620098dda74f674f6409b90fe7fa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- Change the iwl_all_tsc_rsc struct to hold a sta_id (__le32) field,
while preserving the union, used in the older version.
- Adjust the use of this command according to the TLV.
Signed-off-by: Dan Halperin <Dan1.Halperin@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.8c621903db59.I1cc7afedc0ff2009fe1abf007684339f299b73aa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The the driver prevents new Tx from being sent during the remove-station
flow is by invalidating the fw_id_to_mac_id rcu of that station.
However, if there was any Tx still in-flight (tx-cmd was sent but the
ba-notif wasn't received yet) the ba-response to those frames is simply
ignored without actually reclaiming anything. This later causes the
driver to think that that some of the station's queues aren't empty when
in practice they are which causes errors in the station remove flow.
Fix this by performing the tx-reclaim also if the rcu is invalid. any DB
that can't be updated due to this is not very important at this stage
since the station is about to be removed soon anyways.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.72c604b4eda9.I21e75b31a9401870d18747355d4f4305b2fe1db8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to a missing break, the management multicast key was installed even
though we don't really support it. Fix that, so mac80211 would know that
it should protect frames in software.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.019a64e96d44.I609a995611ac5286e442cd54f764eaf4a7249ac0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support v2 of regulatory capability flags parsed from the device
NVM. New API support is determined by FW lookup of the MCC update
command resposnse version, where version 6 supports the new API.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.3d47f4e8ab98.I0fdd2ce23166c18284d2a7a624c40f35ea81cbc2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A FTM responder may do PASN authentication with unassociated stations
to allow secure ranging. In this case, the driver will add an internal
station and install the TK so the FW will accept protected FTM
request frames from this station and will send a protected FTM
response frame.
In addition, the driver needs to configure the HLTK to the FW so
the FW can derive the secure LTF bits. This is left for a later
patch since it is not yet supported by the FW.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.c915b44ad7dd.I72ef7f9753964555561c27ec503241105eddb14e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Evaluate the appropriate DSM from ACPI to set ETSI SRD 5.8GHz
channels to passive or disabled, default behaviour is enabled.
Add enums and refactor evaluation of DSM functions for better
readablity and more informative debug prints.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.816130ee75e0.I727a217be7c967a97960b197a816fc053d10c48a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events, temperature
and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8q7tsACgkQqDIjiipP
6E+5Rwf7BFEn5YXPvng8cmnAlgvEBc9DdT6mGSo0NpFm9MdUxXlaqvw3WWSGyqWQ
+z0Ka7lmn5XyiMsVN11++Snp+79X17HzZf9SXO3glyIpAn+5prTDRhzzj0/jPrtS
sEeI++DrILsKKMGVljzftLmwNJN9DkUDNcnmWmZdCDbYVEKtP9Pjf2wBjAnXj7sX
JA3CkHRMwYLEQbfaKz37M11cYM+LqbDOlb6U11YWgAGGJ7d7zNYRf2/YSYPM4AN6
iE6j0E+3jIlXesULsap1AzeJaBq+wFxj1FL2TUZ8KscvRrm3AucqzNAT2M/Bc5Az
XLKKzc6Gp9JfqB5KXhX2EDu7VRnDBg==
=cSMN
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add support to enable/disable the thermal zones resulting on core
code and drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events,
temperature and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian
Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz
Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
* tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (40 commits)
thermal: intel: intel_pch_thermal: Add Cannon Lake Low Power PCH support
thermal: mediatek: Add tsensor support for V2 thermal system
thermal: mediatek: Prepare to add support for other platforms
thermal: Update power allocator and devfreq cooling to SPDX licensing
MAINTAINERS: update entry to thermal governors file name prefixing
thermal: core: Add thermal zone enable/disable notification
thermal: qcom: tsens-v0_1: Add support for MSM8939
dt-bindings: tsens: qcom: Document MSM8939 compatible
thermal: core: Fix thermal zone lookup by ID
thermal: int340x: processor_thermal: fix: update Jasper Lake PCI id
thermal: imx8mm: Support module autoloading
thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor()
MAINTAINERS: Add maintenance information for IPA
thermal: rcar_gen3_thermal: Do not shadow thcode variable
dt-bindings: thermal: Get rid of thermal.txt and replace references
thermal: core: Move initialization after core initcall
thermal: netlink: Improve the initcall ordering
net: genetlink: Move initialization to core_initcall
thermal: rcar_gen3_thermal: Add r8a774e1 support
thermal/drivers/clock_cooling: Remove clock_cooling code
...
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
The variable ret is being assigned with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200420222449.99481-1-colin.king@canonical.com
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On AX200, the average power was showing positive instead of negative, but
otherwise matched the expected RSSI. Flip the value to negative before
giving to mac80211.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191126214744.1283-1-greearb@candelatech.com
[removed unnecessary check and some unnecessary parentheses]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All iwlwifi cards below the 22000 series are able to handle multiple
keyids per STA and allow the selection of the encryption key per MPDU.
These are therefore fully compatible with the Extended Key ID support
implementation in mac80211.
Enable Extended Key ID support for all dvm cards and the mvm cards not
using the incompatible new Tx API introduced for the 22000 series.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190819180540.2855-1-alexander@wetzel-home.de
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Range request version 10 keeps the same command size as version 9
but uses 2 reserved fields for the responder beacon interval and
station id (if exists).
For now, since the beacon interval of unassoc APs is unknown, use
a value of 100 TUs which is a common value for many APs.
While at it, remove the definition for CCMP_256 cipher, since this
is not supported.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.b7ccdad0805f.I59ea7f773caed85a66c61401066ae169008442e6@changeid
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAl7L1A8ACgkQB8qZga/f
l8T5RQ/9EUxFqBs0cWojwyad5nkesyl51eOnbvSCJJF14W93s2oMeikCynTPe8Vg
km36041QZqGbwmU0yWC9Lmm4y3ja5qQGI+QW+vT6tutGQx6FgK5TzUfYXqiFZqf6
asqkvHpH4VqmbG1KEp0PZjIpW/OVK96pbvtXVnkrcMmjl2JjbRtAhyZQVNtt9ufJ
6wqKf8e6iYqMIInMFPLX+rl7UEknxDKVcqPbMMJmY8/iM1z9Elkg3rkRSMehC+mE
8cznZ6BsjAGCbMiA8K9fUo15lcMfZCJ1hAPzkD4TsJtMEJ0gYDo5jDB8TIpr5uoL
95OnlF8jokJIsO+1g4CyaNSQsmFIuDo84vW8LtGRu9qzTP0UwelxhjZLgE3xlP6b
W+z5HomxfWkYhJhaNywLP3B1VPtJwX8dL/wpECOWHzNKXG7Rb6GqzUwaCRFb6Jjo
TmFJ5wLoEZHhsXYO2dvcyTzCUCXviXvfq60a56IyCJN8wDqmcubePv0+NOHUmj3c
E71NTYymM3j9agdSpXdCFLBXA1OgyIydeSNHuBlaPA4sK6tr4ikUtbOrABjYTaQz
2BB5fHEi8gs4EiHbSXqLFBot3JHljKJPsSN0wAgzQffN+6Kts9FG6HcrLsL+duDg
lRdAzRrunE85S0QhsxeVIX216rX4W08sl0B1rJR+dTMX9ByblAk=
=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can currently end up transmitting on an unallocated queue, if
the allocation fails. Stop doing that, by simply not transmitting.
We don't have any better strategy here, unfortunately, but the
previous commits make that much less likely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.dcf1801f25ef.I6d71e13ea042765800f2ee41401b8eb282527c34@changeid
We currently attempt to allocate queues that are 512 entries long,
but that requires 32 KiB memory, which may not be available, at
least not contiguously. If we fail to allocate, attempt to use a
smaller queue all the way down to 16 entries (which fit into a
single page).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.c8548d7cc08a.I5059c410e628726cbce98d6311b690c632d00f97@changeid
For ACK_ENABLED and 32BIT_BA_BITMAP flags check the station capabilities
rather than bss_conf.ack_enabled and bss_conf.multi_sta_back_32bit.
These fields are stations capabilities and should not be in bss_conf.
Also note that the bss_conf flags are set in station mode only.
In the next patch I will remove ack_enabled and multi_sta_back_32bit
from the bss_conf structure.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200424182644.bc7230b74f93.I144f73cd6a797a7060429981fee62572861bc76b@changeid
If we set amsdu_len one after another the second one overwrites
the orig_amsdu_len so allow only moving from debug to non debug state.
Also the TLC update check was wrong: it was checking that also the orig
is smaller then the new updated size, which is not the case in debug
amsdu mode.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: af2984e9e6 ("iwlwifi: mvm: add a debugfs entry to set a fixed size AMSDU for all TX packets")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200424182644.e565446a4fce.I9729d8c520d8b8bb4de9a5cdc62e01eb85168aac@changeid
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
-----BEGIN PGP SIGNATURE-----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=SKNj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three changes:
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add framework for supporting specific PHY filter configuration,
which allows for application of various FW defined PHY filters
(one per antenna). Change phy_cfg_cmd to the new API (ver3).
Reading of configuration from platform's ACPI tables to be added
later when tables are defined.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200418110539.242a8f979592.I13c77a8a8dbf1a169b5052c7af1f8401ff3991ad@changeid
Add support for the new WOWLAN_GET_STATUS notification that contains a
new element that informs the driver of TIDs whose BA sessions were
closed during suspend.
Note that the new functionality of handling these closed sessions is not
implemented in this patch it. It only aligns to the new API version.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200417131727.b02153b94c1d.Ieb6291586d60f372d5a505604b18227ef97e7202@changeid
The API version lookup is parsed from a TLV and should be in shared code
make make it reusable across all opmodes.
Also change the function names from mvm to fw, since this is not
mvm-specific anymore.
Additionally, since this function is not just a single line of code, it
shouldn't be inline. Convert them to actual functions.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200421133326.cf94672dfcdb.I5ede9cc25ee8de7b8d2b5c574f917a18971da734@changeid
Somehow we missed this for a long time, but similar to the extended
NSS support in VHT capabilities, we need to have this in Operating
Mode notification.
Implement it by
* parsing the 160/80+80 bit there and setting the bandwidth
appropriately
* having callers of ieee80211_get_vht_max_nss() pass in the current
max NSS value as received in the operating mode notification in
order to modify it appropriately depending on the extended NSS
bits.
This updates all drivers that use it, i.e. only iwlwifi/mvm.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.098483728cfa.I4e8c25d3288441759c2793247197229f0696a37d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function iwl_mvm_remove_inactive_tids() returns bool, so we
should just check "if (ret)", not "if (ret >= 0)" (which would
do nothing useful here). We obviously therefore cannot use the
return value of the function for the free_queue, we need to use
the queue (i) we're currently dealing with instead.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.9d862ed72535.I9e27ccc3ee3c8855fc13682592b571581925dfbd@changeid
Due to some hardware issues, queue 31 isn't usable on devices that have
32 queues (7000, 8000, 9000 families), which is correctly reflected in
the configuration and TX queue initialization.
However, the firmware API and queue allocation code assumes that there
are 32 queues, and if something actually attempts to use #31 this leads
to a NULL-pointer dereference since it's not allocated.
Fix this by limiting to 31 in the IWL_MVM_DQA_MAX_DATA_QUEUE, and also
add some code to catch this earlier in the future, if the configuration
changes perhaps.
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.98a79be2db6a.I3a4af6b03b87a6bc18db9b1ff9a812f397bee1fc@changeid
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJefdsZAAoJEG4XJFUm622blekH/2fIoUtl8Kdih38hNjz63PLD
x+LCPjZdRjrmFGTSxnS1rZiIM7v2yXyLGiyq+yr2ltzkpTi8xWOkKL6US8RCew9R
otRtZyLrhgMLG2ExDna1fI5ZJAtLnxV31TCy6yrSUDZ8t4VxMNIB4si3WRzKvAfU
c+cQcsnWr+pCDnbxh53BcYIyiEqKlttw/fGuIKchKuYMQy7DV6nxMdTaAym5Szzi
Nlb8fhXWFaPrPQ6NtHb5WWm4Er3wtMzN/AG8aFVxjrik07vTxQKWamdT9CeK2tDT
iDbx2HaNCWFMulXeZMrc9+inoAzj3UjbPqH3OTUk9iHbVA0unc3CdEBFD9h928Q=
=D/FA
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
====================
Kalle gave me directions on how to resolve the iwlwifi conflict
as follows:
====================
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the places using this want the newline, but not all,
so remove the newline from it and generate it in the debugfs
files where it's desired.
The effect of this is not printing double newlines in debug
log messages.
Change-Id: Ia59b0abbef16b6783fcabc095c5fde16bd047a26
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW changed the maximum number of scan offload profiles to 8 in new
APIs. Support it by changing the scan_offload_profile_cfg struct to be
more dynamic, so we can reuse most of the code and only change size of
the profiles array.
Change-Id: I65210cf541af46e2675a8c764d5871f7f5b070d6
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new command is mostly backwards compatible, with the exception
that the device_type element was changed into a bitmask. The device
type bit remains the same (because we only had 0 and 1 anyway), but
when using v1 we can't set any other bits, because that would change
the integer.
Other than that, the struct remains the same and the driver can set
the device_type bit in both cases, but it can only set the low_latency
bit if VER_2 is used.
Change-Id: Ib68d4c821ebcce253b42ed0ea15881fb4e3e01da
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These values are selected based on the PCI device ID, so the decision
to use them can be made early. By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean). This will also allow us to make
more decisions based on, for instance, the SoC type in used.
The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.
Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We shouldn't do this just for HT/VHT, but be future-proof
and also check for HE.
Change-Id: Icaeff714c00a773681dbfee72558afd1c7121c5d
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
That closing brace for the switch statement is misplaced, fix it.
Change-Id: I39af135a9e3fc64337d2cced43a70cb48fe3b9c1
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Modify adaptive dwell number of APs override API
Instead of using channel to index mapping, add the adaptive dwell
override parameters as part of the configuration per channel in the scan
request command.
Support 2 different override values and use them as follows:
1. 10 APs for friendly GO channels in p2p scan.
2. 2 APs for social channels in p2p scan.
Change-Id: I3b461108abf2306c3d054099112f2c3afce1cc92
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some devices require longer time to stabilize the power and XTAL.
This is especially true for devices integrated in the SoC. Add
support for a new firmware API that allows the driver to set the
latency value accordingly.
Change-Id: I6829a46b89e4e701f80a0e4033f4dd41ee44ed12
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The GEO_TX_POWER_LIMIT command was sent although
there is no wgds table, so the fw got wrong SAR values
from the driver.
Fix this by avoiding sending the command if no wgds
tables are available.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Fixes: 39c1a9728f ("iwlwifi: refactor the SAR tables from mvm to acpi")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tested-By: Jonathan McDowell <noodles@earth.li>
Tested-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200318081237.46db40617cc6.Id5cf852ec8c5dbf20ba86bad7b165a0c828f8b2e@changeid
The AP may set the LDPC capability only in HE (IEEE80211_HE_PHY_CAP1),
but we were checking it only in the HT capabilities.
If we don't use this capability when required, the DSP gets the wrong
configuration in HE and doesn't work properly.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: befebbb30a ("iwlwifi: rs: consider LDPC capability in case of HE")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151128.492d167c1a25.I1ad1353dbbf6c99ae57814be750f41a1c9f7f4ac@changeid
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic for checking required NVM sections was recently fixed in
commit b3f20e0982 ("iwlwifi: mvm: fix NVM check for 3168
devices"). However, with that fixed the else is now taken for 3168
devices and within the else clause there is a mandatory check for the
PHY_SKU section. This causes the parsing to fail for 3168 devices.
The PHY_SKU section is really only mandatory for the IWL_NVM_EXT
layout (the phy_sku parameter of iwl_parse_nvm_data is only used when
the NVM type is IWL_NVM_EXT). So this changes the PHY_SKU section
check so that it's only mandatory for IWL_NVM_EXT.
Fixes: b3f20e0982 ("iwlwifi: mvm: fix NVM check for 3168 devices")
Signed-off-by: Dan Moulding <dmoulding@me.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Continue the wakeup flow only if no FW CPUs have an error
If we don't check for error in all FW CPUs the driver can think
based on one CPU that the FW is operational and try to access
and send commands.
Also, handle the error_id endianness correctly as le32
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I changed the API for asking for a session protection but
I omitted the TDLS flows. Fix that now.
Note that for the TDLS flow, we need to block until the
session protection actually starts, so add this option
to iwl_mvm_schedule_session_protection.
This patch fixes a firmware assert in the TDLS flow since
the old TIME_EVENT_CMD is not supported anymore by newer
firwmare versions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix a kernel panic by checking that the sta is not NULL.
This could happen during a reconfig flow, as mac80211 moves the sta
between all the states without really checking if the previous state was
successfully set. So, if for some reason we failed to add back the
station, subsequent calls to sta_state() callback will be done when the
station is NULL. This would result in a following panic:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000040
IP: iwl_mvm_cfg_he_sta+0xfc/0x690 [iwlmvm]
[..]
Call Trace:
iwl_mvm_mac_sta_state+0x629/0x6f0 [iwlmvm]
drv_sta_state+0xf4/0x950 [mac80211]
ieee80211_reconfig+0xa12/0x2180 [mac80211]
ieee80211_restart_work+0xbb/0xe0 [mac80211]
process_one_work+0x1e2/0x610
worker_thread+0x4d/0x3e0
[..]
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a FTM request is aborted, the driver sends the abort command to
the fw and waits for a response. When the response arrives, the driver
calls cfg80211_pmsr_complete() for that request.
However, cfg80211 frees the requested data immediately after sending
the abort command, so this may lead to use after free.
Fix it by clearing the request data in the driver when the abort
command arrives and ignoring the fw notification that will come
afterwards.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Fixes: fc36ffda32 ("iwlwifi: mvm: support FTM initiator")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Till now, the driver asked the fw for a DTS measurement in automatic
mode. This triggered a flow in which the fw actively measured the
temperature. This is not needed anymore, as the fw performs
measurements by itself, without the driver triggering them, and the
current cadence in which the fw performs such measurements is
sufficient.
In addition, in some time-sensitive scenarios, in which the driver asks
the fw for an active measurement twice in a short time (<100ms), the fw
asserts with code 0x20100801.
Change the DTS measurement to _WITHOUT_MEASURE instead, so the fw will
respond with the last measurement it has performed.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IGTK keys are only removed by mac80211 after it has already
removed the AP station. This causes the driver to throw an error
because mac80211 is trying to remove the IGTK when the station doesn't
exist anymore.
The firmware is aware that the station has been removed and can deal
with it the next time we try to add an IGTK for a station, so we
shouldn't try to remove the key if the station ID is
IWL_MVM_INVALID_STA. Do this by removing the check for mvm_sta before
calling iwl_mvm_send_sta_igtk() and check return from that function
gracefully if the station ID is invalid.
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use a unique name when registering a thermal zone. Otherwise, with
multiple NICS, we hit the following warning during the unregistration.
WARNING: CPU: 2 PID: 3525 at fs/sysfs/group.c:255
RIP: 0010:sysfs_remove_group+0x80/0x90
Call Trace:
dpm_sysfs_remove+0x57/0x60
device_del+0x5a/0x350
? sscanf+0x4e/0x70
device_unregister+0x1a/0x60
hwmon_device_unregister+0x4a/0xa0
thermal_remove_hwmon_sysfs+0x175/0x1d0
thermal_zone_device_unregister+0x188/0x1e0
iwl_mvm_thermal_exit+0xe7/0x100 [iwlmvm]
iwl_op_mode_mvm_stop+0x27/0x180 [iwlmvm]
_iwl_op_mode_stop.isra.3+0x2b/0x50 [iwlwifi]
iwl_opmode_deregister+0x90/0xa0 [iwlwifi]
__exit_compat+0x10/0x2c7 [iwlmvm]
__x64_sys_delete_module+0x13f/0x270
do_syscall_64+0x5a/0x110
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeLcWsAAoJEG4XJFUm622bDGUIAJuhM4LiDAzOGnDjH5cMosOC
/qwDpGD19cEeVAhNSMKUn7Uo9+qbQYIleiO7XXxzCuJceYbxbT5s3Vb/fWsRUPjS
cBDmGuK8/giqMQJshXvfCTsoF83CyirCjY/MJvomK2BRlXM8hQ3s6hAcfU0zQ96e
OU1akcfZzUwjaBKaDYLncxLuGbeUXMy8AZwFdgQlQRMoObpen/IIwx6jDK/A+3l6
VCOJF+JTkDytfNWmTpZ65uJrYEXoLe6G4028FjOI4BDFmEgvdHC5vTm7VOBhrkuB
9tsKcYNvECCNn2WI96V+etD8kaZPscQIW8hgOrYyGxw43lJg5zH4Z9eWAmHojxE=
=UOhb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
-----BEGIN PGP SIGNATURE-----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=Ovcw
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.6
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
The purpose of this was to keep all the queues updated with
the Rx sequence numbers because unlikely yet possible
situations where queues can't understand if a specific
packet needs to be dropped or not.
Unfortunately, it was reported that this caused issues in
our DMA engine. We don't fully understand how this is related,
but this is being currently debugged. For now, just don't send
this notification to the Rx queues. This de-facto reverts my
commit 3c514bf831:
iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues
This issue was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=204873https://bugzilla.kernel.org/show_bug.cgi?id=205001
and others maybe.
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
CC: <stable@vger.kernel.org> # 5.3+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is now possible to propagate BSS color settings into the subsystem. Lets
make mac80211 also handle them so that we can send them further down the
stack into the drivers. We drop the old bss_color field and change iwlwifi
to use the new he_bss_color struct.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a straight-forward conversion case for the new function, and
while we're at it, we can remove a null write to skb->next by replacing
it with skb_mark_not_on_list.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a lot of mostly duplicated data structures that are repeated
only because the device name string is different. To avoid this, move
the string from the cfg to the trans structure and add it
independently from the rest of the configuration to the PCI mapping
tables.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print out the secure boot status, extended by the PCs of LMACs
and the UMAC. This needs to be before dumping, as dumping will
corrupt the PC (if the NMI is handled), so move that down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since v5.4-rc1 was released, iwlwifi started throwing errors when scan
commands were sent to the firmware with certain devices (depending on
the OTP burned in the device, which contains the list of available
channels). For instance:
iwlwifi 0000:00:14.3: FW error in SYNC CMD SCAN_CFG_CMD
This bug was reported in the ArchLinux bug tracker:
https://bugs.archlinux.org/task/64703
And also in a specific case in bugzilla, when the lar_disabled option
was set: https://bugzilla.kernel.org/show_bug.cgi?id=205193
Revert the commit that introduced this error, by using the number of
channels from the OTP instead of the number of channels that is
specified in the FW TLV that tells us how many channels it supports.
This reverts commit 06eb547c4a.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Mehmet Akif Tasova <makiftasova@gmail.com>
[ Luca: reworded the commit message a bit. ]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is an old parameter that was used supposed to be used only when
LAR was still under development. It should not be used anymore, but,
since it's available, end-users have been mangling with it
unnecessarily. In some cases it can cause problems because when LAR
is supported the driver and the firmware do not expect it to be
disabled.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we transmit after TXQ dequeue, we aren't paying attention to
the return value of the transmit functions, leading to a potential
SKB leak.
Refactor the code a bit (and rename ..._tx to ..._tx_sta) to check
for this happening.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It used to be the case that if we got here, we wouldn't warn
but instead allocate the queue (DQA). With using the mac80211
TXQs model this changed, and we really have nothing to do with
the frame here anymore, hence the warning now.
However, clearly we missed in coding & review that this is now
a pure error path and leaks the SKB if we return 0 instead of
an indication that the SKB needs to be freed. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API requires the driver to config the supported frame format
(legacy, HT, VHT etc.).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API requires the driver to set the frame format
(legacy, HT, VHT etc.) to be used for the measurement.
The new API also supports 11az and secured measurement, but
these are not supported by the driver for now.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When receiving a new MCC driver get all the data about the new country
code and its regulatory information.
Mistakenly, we ignored the cap field, which includes global regulatory
information which should be applies to every channel.
Fix it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have offloaded rate scaling, which is always true for those
devices supporting HE, then report the TX rate directly from the
data the firmware gives us, instead of only passing it to mac80211
on frame status only and for it to track it.
First of all, this makes us always report the last good rate that
the rate scaling algorithm picked, which is better than reporting
the last rate for any frame since management frames etc. are sent
with very low rates and could interfere.
Additionally, this allows us to properly report HE rates, though
in case there's a lot of trigger-based traffic, we don't get any
choice in the rates and don't report that properly right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We had a check on !NVM_EXT and then a check for NVM_SDP in the else
block of this if. The else block, obviously, could only be reached if
using NVM_EXT, so it would never be NVM_SDP.
Fix that by checking whether the nvm_type is IWL_NVM instead of
checking for !IWL_NVM_EXT to solve this issue.
Reported-by: Stefan Sperling <stsp@stsp.name>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As noted in the previous commit, due to the way we allocate the
dev_cmd headers with 324 byte size, and 4/8 byte alignment, the
part we use of them (bytes 20..40-68) could still cross a page
and thus 2^32 boundary.
Address this by using alignment to ensure that the allocation
cannot cross a page boundary, on hardware that's affected. To
make that not cause more memory consumption, reduce the size of
the allocations to the necessary size - we go from 324 bytes in
each allocation to 60/68 on gen2 depending on family, and ~120
or so on gen1 (so on gen1 it's a pure reduction in size, since
we don't need alignment there).
To avoid size and clearing issues, add a new structure that's
just the header, and use kmem_cache_zalloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The fw already support scan api v12,
v11 is not needed anymore.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a long-standing bug - we haven't been able to check the
firmware image that was loaded for D3/not-D3 since the introduction
of the unified image...
Fix this by keeping a status flag for D3 instead of checking for
the firmware image that's loaded.
This reduces occurrences of checks for IWL_UCODE_WOWLAN to just the
code that actually loads the image or deals with it in other ways.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
we should not send the PPAG (Per-Platform Antenna Gain)
command to FW unless the platform has this ACPI table and it was
read and validated during the init flow. also no need to send the
command if the feature is disabled, so check if enabled before
sending, as if there is no valid table the feature is disabled.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
kasprintf() can fail, we should check the return value.
Fixes: 5ed540aecc ("iwlwifi: use mac80211 throughput trigger")
Fixes: 8ca151b568 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no multicast wake lock in the driver, remove the comment
that refers to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes it easier for user-space to know how many antennas the
radio has. Seems to work with the AX200 radio, at least.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This email alias (ilw@linux.intel.com) hasn't been functional
for probably closer to a decade than not, remove it. It's not
really clear to me how this ended up in new code though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This field isn't set by any configuration, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
1. Modify channel config flags to be used for legacy bands channels
as well, to indicate SSIDs elements from ssidIEsArray.
2. Add new general flag.
3. Remove ssidNum from probe params.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code now compiles without ACPI, but there's a warning since
iwl_mvm_get_ppag_table() isn't used, and iwl_mvm_ppag_init() must
not unconditionally fail but return success instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current budget of 2000mA is preventing us from reaching maximum
throughput. According to our system engineers, we can increase the
maximum budget to 2400mA to solve this problem.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are various of flows which require tids flushing
(disconnection, suspend, etc...).
Currently, when the driver instructs the FW to flush
he masks all the data tids(0-7).
However, the driver doesn't set the management tid (#15)
which cause the FW not to flush it.
When the FW tries to remove the mgmt queue he throws an assert
since it is not an empty queue.
instead of just set only the data tids set everything and let
the FW ignore the invalid tids.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to the requirement update and support adaptive dwell in p2p scan.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Refactored the SAR related functions from iwlmvm to acpi
in order to make it shared between different opmodes
in addition to removing unused variable ppag_rev.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement scan request command version 12.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement a new versioning handling flow supported from version 11
onwards.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is present since the introduction of iwlmvm.
Example stack trace on MIPS:
[<ffffffffc0789328>] iwl_mvm_rx_rx_mpdu+0xa8/0xb88 [iwlmvm]
[<ffffffffc0632b40>] iwl_pcie_rx_handle+0x420/0xc48 [iwlwifi]
Tested with a Wireless AC 7265 for ~6 months, confirmed to fix the
problem. No other unaligned accesses are spotted yet.
Signed-off-by: Wang Xuerui <wangxuerui@qiniu.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the rs_pretty_print_rate() function to print the rate_n_flags in
more human-readable format.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW scan api ver 11 adds support for some new features,
in this version the fw did also some cleanup in the api,
which causes the driver not to be able to use the
current scan req struct.
Therefore, in this patch the driver has new version for the scan command
code
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the code to build scan cmd is duplicated in
iwl_mvm_reg_scan_start and iwl_mvm_sched_scan_start.
Create a function to build this command, and call the function instead.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the next patch, this code will be used from different places.
As preparation export this code into function.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add assert time point in the D3 resume flow in case there was an assert
during D3.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 limits amsdu size to the minimum of HT and VHT capabilities
but since in a VHT connection we don't transmit HT frames we can discard
HT limits.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We return in the if block, so it's unnecessary to have an else
statement. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the single antenna diversity support was sent upstream, only some
definitions were sent, due to a bad revert.
Fix this by adding the actual code.
Fixes: 5952e0ec3f ("iwlwifi: mvm: add support for single antenna diversity")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
The API was reduced to include only knowledge currently needed by the
FW scan logic, the rest is legacy. Support the new, reduced version.
Using the old API with newer firmwares (starting from
iwlwifi-*-50.ucode, which implements and requires the new API version)
causes an assertion failure similar to this one:
[ 2.854505] iwlwifi 0000:00:14.3: 0x20000038 | BAD_COMMAND
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FW introduce new API to get the band from the rx mpdu,
use this new API.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
OFDM rate used for all bands except to band 2.4 which use CCK rate.
Inverting the condition help that in future we won't need to expand the
condition for more bands.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow to fire user trigger in ini mode
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A missed VAP notification will be sent from umac when
the station is out of sync with its associated non-transmitted
BSSID. The notification will be sent only if the transmitted
BSSID is an EMA-AP one.
The driver will consider this notification as connection loss.
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There expect the 'static' keyword to come first in a
declaration, and we get warnings like this with "make W=1":
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c:427:1: warning:
'static' is not at beginning of declaration [-Wold-style-declaration]
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c:434:1: warning:
'static' is not at beginning of declaration [-Wold-style-declaration]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware has now a new session protection command.
This new API allows the firmware to manage the protection
needed for association. It'll also remove the event when
the association is complete.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This prototype is no longer used, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During D3 state there are some flows which requires FW reset.
Add new API to support it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
debugfs amsdu_len sets only the max_amsdu_len for ieee80211 station
so take it into consideration while getting max amsdu
Fixes: af2984e9e6 ("iwlwifi: mvm: add a debugfs entry to set a fixed size AMSDU for all TX packets")
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pass the FW notification packet to the dump collection flow to allow
the driver to include it in the dump file if requested.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_tvqm_enable_txq() can return an error, notably if unable
to allocate memory for the queue. Handle this error throughout,
avoiding storing the invalid value into a u16 which later leads
to a disable of an invalid queue ("queue 65524 not used", where
65524 is just -ENOMEM in a u16).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We currently support two NICs in FW version 29, namely 7265D and 3168.
Out of these, only 7265D supports GEO SAR, so adjust the function that
checks for it accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f5a47fae6a ("iwlwifi: mvm: fix version check for GEO_TX_POWER_LIMIT support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Consider the following flow:
1. Driver starts to sync the rx queues due to a delba.
mvm->queue_sync_cookie=1.
This rx-queues-sync is synchronous, so it doesn't increment the
cookie until all rx queues handle the notification from FW.
2. During this time, driver starts to sync rx queues due to nssn sync
required.
The cookie's value is still 1, but it doesn't matter since this
rx-queue-sync is non-synchronous so in the notification handler the
cookie is ignored.
What _does_ matter is that this flow increments the cookie to 2
immediately.
Remember though that the FW won't start servicing this command until
it's done with the previous one.
3. FW is still handling the first command, so it sends a notification
with internal_notif->sync=1, and internal_notif->cookie=0, which
triggers a WARN_ONCE.
The solution for this race is to only use the mvm->queue_sync_cookie in
case of a synchronous sync-rx-queues. This way in step 2 the cookie's
value won't change so we avoid the WARN.
The commit in the "fixes" field is the first commit to introduce
non-synchronous sending of this command to FW.
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PHY is initialized during device initialization, but devices with
the tx_siso_diversity flag set need to send PHY_CONFIGURATION_CMD first,
otherwise the PHY would be reinitialized, causing a SYSASSERT.
To fix this, use a bit that tells the FW not to complete the PHY
initialization before a PHY_CONFIGURATION_CMD is received.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can't check for the ACPI table revision validity in the same if
where we check if the package was read correctly, because we return
PTR_ERR(pkg) and if the table is not valid but the pointer is, we
would return a valid pointer as an error. Fix that by moving the
table checks to a separate if and return -EINVAL if it's not valid.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The intention was to have the GEO_TX_POWER_LIMIT command in FW version
36 as well, but not all 8000 family got this feature enabled. The
8000 family is the only one using version 36, so skip this version
entirely. If we try to send this command to the firmwares that do not
support it, we get a BAD_COMMAND response from the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=204151.
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without CONFIG_THERMAL, the driver fails to link as it calls
iwl_mvm_send_temp_report_ths_cmd() unconditionally. Fix this
by making that function available, but do almost nothing but
send the empty firmware command to enable CT-kill reporting.
While at it, also fix that function itself to not error out
when the thermal zone hasn't been initialized, but instead
just send the empty firmware command in this case as well.
Fixes: 242d9c8b9a ("iwlwifi: mvm: use FW thermal monitoring regardless of CONFIG_THERMAL")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use cancel_delayed_work_sync on the dump workers only in case of
unloading the op mode. In any other case use iwl_fw_flush_dumps or
iwl_fw_dbg_stop_sync (depends if the op mode mutex is held or not).
This way, the driver will wait until debug data is collected in all
cases but op mode unloading.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove periodic trigger functionality.
After moving to the new API we will add periodic trigger functionality
that matches the new API.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support code to be able to use the DRAM buffer allocation command,
which allows us to send information about a buffer to the firmware
to use it with the DBGC hardware.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the "apply points" mechanism as preparation for the changed
debug API where this is now a "time point" instead. Use a new API
across the code at the trigger points ("time points"), but don't
yet implement it since that requires some more preparation.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes the firmware won't be able to decrypt frames
because the keys were not installed yet or other scenarios.
The firmware will soon stop dropping multicast frames when
MAC_FILTER_ACCEPT_GRP is not set. The firmware will simply
always pass multicast frame in.
In order to avoid logging any such frame coming in when we
don't have the keys, drop the print.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In prior hardware generations (e.g. 9000 series), we received the BAR
frame with fake NSSN information to handle releasing frames from the
reorder buffer for the default queue, the other queues were getting
the FRAME_RELEASE notification in this case.
With multi-TID block-ack, the firmware no longer sends us the BAR
frame because the fake RX is quite big (just the metadata is around
48 bytes or so). Instead, it now sends us one (or multiple) special
release notifications (0xc2). The hardware consumes these as well,
but only generates the FRAME_RELEASE (0xc3) for queues other than
the default queue. We thus need to handle them in the same way we
handle the normal FRAME_RELEASE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Certain APs (I think a certain Broadcom model) interact badly with our
full state BA bitmap handling, and if triggered badly with many powersave
transitions they keep sending frames from before the window, which our
hardware then doesn't appear to ACK (to them) since it has moved on and
is sending ACKs for higher SNs now.
Try to detect this situation and if this keeps happening, disable the
aggregation session.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
WoWlan feature within the FW uses the station id for various of reasons.
Thus we need to add this information to the command.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new device generation has a slightly different suspend resume flow
Currently, the way the driver instruct the device to move to D3 is by
sending D3_CONFIG_CMD.
Instead of using the host command the indication is by writing to the
doorbell interrupt.
The FW will respond with interrupt to indicate transition completion.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
separate configuration flows and dump collection flows.
make ini configuration flows be in iwl-dbg-tlv.c and dump related flows
in dbg.c to better reflect their logical difference.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Can't rely that band 2.4 is always supported by the NIC and use the
first channel in this band for the phy ctxt.
Instead, look for the first channel in the first band that is supported
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
use iwl_trans_dbg_ini_valid function instead of a boolean value check if
dbg_ini mode is on. It is needed for a future patch.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TX power limits as defined in the OTP assume the worst case scenario
in terms of the platform's atenna gain, but most platforms are below
that value so they can use more TX power without passing the regulatory
limit. If the platform indicates in the BIOS that it indeed has lower
gain, and the geographic location allows it, higher TX power can be
used. The driver reads the PPAG (Per-Platform Antenna Gain) data from
BIOS (if it exists), validates it and sends the appropriate command to
the FW. This flow happens once at FW init, in case of suspend/resume
there is no need to read again from BIOS as we save those values during
init, so just send the PPAG command again to FW.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The check is not necessary anymore, because now the struct is not
allocated separately, but is part of the mvmsta struct. Remove the
check, since it's dead code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Any firmware that supports the new channel switch flow is
able to close / re-open the queues when needed. It takes
into account the channel switch mode etc...
Don't open / close the queues or enable / disable beacon
abort before and after the channel switch in case the
firmware is able to do this by itself.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Function iwl_mvm_scan_set_legacy_probe_req() second argument
size is too large to be passed by value.
Fix it to be passed by reference.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This means:
1) stop calling pm_runtime_resume when starting the hardware
2) removing the unneeded low_power parameter to start / stop hw / fw
transport ops
3) squashing transport functions that are now the same
_iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During D3 state, FW may send packets.
As a result, "write" queue pointer will be incremented by FW.
Upon resume from D3, driver should adjust its shadows of "write" and "read"
pointers to the value reported by FW.
1. Keep TID used during wowlan configuration.
2. Upon resume, set driver's "write" and "read" queue pointers
to the value reported by FW.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It doesn't make sense to use the FW thermal monitoring only if we
have CONFIG_THERMAL, because then we use the default thresholds
etc. which may be different from what the firmware implements, as
we don't maintain them in the driver now. Only the CTDP code needs
to actually be under CONFIG_THERMAL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's hard to follow the numbers so rename it with enum
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Scan API was changed to support 6Ghz channels as well.
Support the new version.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New FW versions introduces LTR feature enablement by default.
For such FW versions, driver (mvm/xvt) should not send
host command to enable LTR feature, also it should be possible to
override LTR configuration through the debugfs.
1. Send LTR feature enablement command only for FW versions
which does not advertises SET_LTR_GEN2 capability.
2. Implement ltr_config file in debugfs for LTR configuration override.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
We're now left with a status bit that is never set and a few
other leftovers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Also change the signature of the power functions that won't
receive d0i3=true anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This variable read, but never set. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that d0i3 is dead, this function can't be called from d0i3
flows. Change its signature and make it static.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For runtime PM to work with d0i3 code, a lot of integration work needs
to be done with the platform (e.g. the out-of-band wake up interrupt)
and we currently don't have any platforms where this integration
happened. So, this code has been pretty much stale for a while and
when someone enables it, it just breaks things.
Therefore, to simplify the code base and make sure no one enables this
by mistake, we will remove the whole code.
This is only the very start, much more work is needed.
Remove the places where we check iwl_mvm_is_d0i3_supported
but leave all the refs, those will be removed in a different
patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When printing a TX, add to the print the length of the frame.
That will help with BSEP (buffer status report poll) tests.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use the actual length of channels array and not the max capable length.
Signed-off-by: Beker Ayala <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
add support to print ldbg command in mvm and xvt mode
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support the new DBGC_SUSPEND_RESUME command to change the recording state.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These static functions are only used after their definition,
so we don't need the forward declarations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case that there are OBSS that do not know how to properly
interpret 26-tone RU OFDMA transmissions, instruct the FW not
to use such transmissions.
The check is currently only performed upon association.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If mvm->fwrt.cur_fw_img != IWL_UCODE_INIT, then
rfkill_safe_init_done must be true since
rfkill_safe_init_done is set to true before we start to load
the runtime image.
Remove the redundant condition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The newer targets don't support the DQA enablement command
and will return error status, while older targets need it.
The feature is defined by the corresponding TLV.
Send the command only if the TLV is enabled.
Signed-off-by: Ilia Lin <ilia.lin@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MAC context configuration always allowed multicast data frames
to pass to the driver for all MAC context types, and in the
case of station MAC context both when associated and when not
associated.
One of the outcomes of this configuration is having the FW forward
encrypted multicast frames to the driver with Rx status indicating
that the frame was not decrypted (as expected, since no keys were
configured yet) which in turn results with unnecessary error
messages.
Change this behavior to allow multicast data frames only when they
are actually expected, e.g., station MAC context is associated etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Accessing the hdr of an skb that was consumed already isn't
a good idea.
First ask if the skb is a QoS packet, then keep that data
on stack, and then consume the skb.
This was spotted by KASAN.
Cc: stable@vger.kernel.org
Fixes: 08f7d8b69a ("iwlwifi: mvm: bring back mvm GSO code")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The index for the elements of the ACPI object we dereference
was static. This means that if we called the function twice
we wouldn't start from 3 again, but rather from the latest
index we reached in the previous call.
This was dutifully reported by KASAN.
Fix this.
Cc: stable@vger.kernel.org
Fixes: 6996490501 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We erroneously added a check for FW API version 41 before sending
GEO_TX_POWER_LIMIT, but this was already implemented in version 38.
Additionally, it was cherry-picked to older versions, namely 17, 26
and 29, so check for those as well.
Cc: stable@vger.kernel.org
Fixes: eca1e56cee ("iwlwifi: mvm: don't send GEO_TX_POWER_LIMIT to old firmwares")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
lq_info is an arary of size 2, active_tbl index is u8.
When accessing lq_info[1 - active_tbl], theoretically it's possible
that the access will be made to a negative index value.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An earlier patch made sure that the queues are not lagging
too far behind. This means that iwl_mvm_release_frames
should not be called with a head_sn too far behind NSSN.
Don't take the risk to change completely the entry
condition to iwl_mvm_release_frames, but don't update
the head_sn is the NSSN is more than 2048 packets ahead
of us. Since this just cannot be right. This means that
the scenario described here happened. We are queue 0.
Q:0 Q:1
head_sn: 0 -> 2047
head_sn: 2048
Lots of packets arrive:
head_sn: 2047 -> 2150
send NSSN_SYNC notification
Handle notification
from the firmware and
do NOT move the head_sn
back to 2048
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The solution with the worker still had a bug, as in order
to get sta, rcu_read_lock should be used and thus no mutex
can be used inside iwl_mvm_rs_rate_init.
Also, spin_lock is a simpler solution, no need to spawn a
dedicated worker.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only place where the command was sent as SYNC is during
init and this is not really critical. This change is required
for replacing RS mutex with a spinlock (in the subsequent patch),
since SYNC comamnd requres sleeping and thus the flow cannot
be done when holding a spinlock.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comparison of the u32 variable wgds_tbl_idx with less than zero is
always going to be false because it is unsigned. Fix this by making
wgds_tbl_idx a plain signed int.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: 4fd445a2c8 ("iwlwifi: mvm: Add log information about SAR status")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code clearly never could have worked, since it locks
while already locked. Add an unlocked __iwl_mvm_mac_set_key()
variant that doesn't do locking to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_rs_tx_status can be called from two places in the code, but the
mutex is taken only on one of the calls. Split it into a wrapper taking
locks and an internal __iwl_mvm_rs_tx_status function.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support MSI-X efficiently, we want to avoid
communication across Rx queues. Each Rx queue should have
all the data it needs to process a packet.
The reordering buffer is a challenge in the MSI-X world
since we can have a single BA session whose packets are
directed to different queues. This is why each queue has
its own reordering buffer. The hardware is able to hint
the driver whether we have a hole or not, which allows
the driver to know whether it can release a packet or not.
This indication is called NSSN. Roughly, if the packet's
SN is lower than the NSSN, we can release the packet to
the stack. The NSSN is the SN of the newest packet received
without any holes + 1.
This is working as long as we don't have packets that we
release because of a timeout. When that happens, we could
have taken the decision to release a packet after we have
been waiting for its predecessor for too long. If this
predecessor comes later, we have to drop it because we
can't release packets out of order. In that case, the
hardware will give us an indication that we can we release
the packet (SN < NSSN), but the packet still needs to be
dropped.
This is why we sometimes need to ignore the NSSN and we
track the head_sn in software.
Here is a specific example of this:
1) Rx queue 1 got packets: 480, 482, 483
2) We release 480 to to the stack and wait for 481
3) NSSN is now 481
4) The timeout expires
5) We release 482 and 483, NSSN is still 480
6) 481 arrives its NSSN is 484.
We need to drop 481 even if 481 < 484. This is why we'll
update the head_sn to 484 at step 2. The flow now is:
1) Rx queue 1 got packets: 480, 482, 483
2) We release 480 to to the stack and wait for 481
3) NSSN is now 481 / head_sn is 481
4) The timeout expires
5) We release 482 and 483, NSSN is still 480 but head_sn is 484.
6) 481 arrives its NSSN is 484, but head_sn is 484 and we drop it.
This code introduces another problem in case all the traffic
goes well (no hole, no timeout):
Rx queue 1: 0 -> 483 (head_sn = 484)
Rx queue 2: 501 -> 4095 (head_sn = 0)
Rx queue 2: 0 -> 480 (head_sn = 481)
Rx queue 1: 481 but head_sn = 484 and we drop it.
At this point, the SN of queue 1 is far behind: more than
4040 packets behind. Queue 1 will consider 481 "old"
because 481 is in [501-64:501] whereas it is a very new
packet.
In order to fix that, send an Rx notification from time to
time (twice across the full set of 4096 packets) to make
sure no Rx queue is lagging too far behind.
What will happen then is:
Rx queue 1: 0 -> 483 (head_sn = 484)
Rx queue 2: 501 -> 2047 (head_sn = 2048)
Rx queue 1: Sync nofication (head_sn = 2048)
Rx queue 2: 2048 -> 4095 (head_sn = 0)
Rx queue 1: Sync notification (head_sn = 0)
Rx queue 2: 1 -> 481 (head_sn = 482)
Rx queue 1: 481 and head_sn = 0.
In queue 1's data, head_sn is now 0, the packet coming in
is 481, it'll understand that the new packet is new and it
won't be dropped.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of allocating memory for which we have an upper
limit, use a small buffer on stack.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will soon be using a new notification that will be
initiated by the driver, sent to the firmware and sent
back to all the RSS queues by the firmware. This new
notification will be useful to synchronize the NSSN across
all the queues.
For now, don't send the notification, just add the code to
handle it. Later patch will add the code to actually send
it.
While at it, validate the baid coming from the firmware to
avoid accessing an array with a bad index in the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will need a new type of synchronization message going
through all the RSS queues. Prepare the ground for this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Firmware versions before 41 don't support the GEO_TX_POWER_LIMIT
command, and sending it to the firmware will cause a firmware crash.
We allow this via debugfs, so we need to return an error value in case
it's not supported.
This had already been fixed during init, when we send the command if
the ACPI WGDS table is present. Fix it also for the other,
userspace-triggered case.
Cc: stable@vger.kernel.org
Fixes: 7fe90e0e3d ("iwlwifi: mvm: refactor geo init")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rate perform uses the lq_sta table to calculate the next rate to scale
while rate init resets the same table,
Rate perform is done in soft irq context in parallel to rate init
that can be called in case we are doing changes like AP changes BW
or moving state for auth to assoc.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On older NICs, we occasionally see issues with A-MSDU support,
where the commands in the FIFO get confused and then we see an
assert EDC because the next command in the FIFO isn't TX.
We've tried to isolate this issue and understand where it comes
from, but haven't found any errors in building the A-MSDU in
software.
At least for now, disable A-MSDU support on older hardware so
that users can use it again without fearing the assert.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=203315.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The .remove_sta_debugfs callback was not doing anything in this driver,
so remove it as it is not needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190612142658.12792-4-gregkh@linuxfoundation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
In AP (and IBSS) mode, we can only set GTKs to firmware after we have
sent down the multicast station, but this we can only do after we've
enabled beaconing, etc.
However, during rfkill exit, hostapd will configure the keys before
starting the AP, and cfg80211/mac80211 accept it happily.
On earlier devices, this didn't bother us as GTK TX wasn't really
handled in firmware, we just put the key material into the TX cmd
and thus it only mattered when we actually transmitted a frame.
On newer devices, however, the firmware needs to track all of this
and that doesn't work if we add the key before the (multicast) sta
it belongs to.
To fix this, keep a list of keys to add during AP enable, and call
the function there.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW API was clarified saying that this flag should only be set in
BSS client mode. Remove it from the MAC_CTXT command we send in AP
and GO modes.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 3b5ee8dd8b ("iwlwifi: mvm: set MAC_FILTER_IN_11AX in AP mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 0xF6 command used to start and stop the recording from 22560 devices
was removed. This is causing an assert when the driver tries to alter
the recording state.
Remove the use of the command.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
From 9000 device family the FW automatically stops the debug
recording and the driver should not stop it as well.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TWT is still very new and we expect issues. Make its usage
configurable and disable it by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unite iwl_trans debug related fields under iwl_trans_debug struct to
increase readability and keep iwl_trans clean.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some buggy scenarios we could possible attempt to transmit frames larger
than maximum MSDU size. Since our devices don't know how to handle this,
it may result in asserts, hangs etc.
This can happen, for example, when we receive a large multicast frame
and try to transmit it back to the air in AP mode.
Since in a legal scenario this should never happen, drop such frames and
warn about it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
South Korea is adding a more strict SAR limit called "Limb SAR".
Currently, WGDS SAR offset group 3 is not used (not mapped to any country).
In order to be able to comply with South Korea new restriction:
- OEM will use WGDS SAR offset group 3 to South Korea limitation.
- OEM will change WGDS revision to 1 (currently latest revision is 0)
to notify that Korea Limb SAR applied.
- Driver will read the WGDS table and pass the values to FW (as usual)
- Driver will pass to FW an indication that Korea Limb SAR is applied
in case table revision is 1.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The AC numbers used by mac80211 differ from those used
by the firmware. When setting MU EDCA params for each
AC, use the correct FW AC numbers.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The indexes into the ac array in the iwl_mac_ctx_cmd are from the iwl_ac
enum and not the txfs. The current code therefore puts the edca params
in the wrong indexes of the array, causing wrong priority for
data-streams of different ACs.
Fix this.
Note that this bug only occurs in NICs that use the new tx api, since in
the old tx api the txf number is equal to the corresponding ac in the
iwl_ac enum.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These pointers are an offset into the "sta" struct. They're assigned
like this:
const struct ieee80211_sta_vht_cap *vht_cap = &sta->vht_cap;
They're not the first member of the struct (->supp_rates[] is first) so
they can't be NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*pattern_cmd) +
wowlan->n_patterns * sizeof(struct iwlagn_wowlan_pattern)
to :
struct_size(pattern_cmd, patterns, wowlan->n_patterns)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support adaptive dwell high band default number of APs new api.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we have per station control over amsdu size no need for
multiple entries, especially that the old one is misleading due to not
setting it for all protocols as a limit.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The info struct contains data about the FW, HW, RF and the debug
configuration.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current debugfs entry only limits the max AMSDU for TCP. Add a new
debugfs entry to allow setting a fixed AMSDU size for all TX packets,
including UDP and ICMP
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a dump trigger is fired, the driver sets IWL_FWRT_STATUS_DUMPING and
aborts any consecutive dump collection.
To allow consecutive triggers firing, use 5 dump workers and allocate
them upon incoming dump collection requests.
This functionality is needed since in ini debug mode each trigger may
have entirely different memory regions to collect unlike the legacy
mode in which all the triggers dump the same memory regions.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As iwl_mvm_tx_mpdu() is not disabling BH while obtaining iwl_mvm_sta->lock
(which is being taken from BH context as well), it has to be always
invoked with BH disabled. Make that clear in a comment.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes boot uniformly boottime and tai uniformly clocktai, to
address the remaining oversights.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20190621203249.3909-2-Jason@zx2c4.com
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 29 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.438503728@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TLC_MNG_CONFIG sync cmd sent by the rs leads to a kernel warning
of sleeping while in rcu read-side critical section. The fix is to
change the command to be ASYNC (not blocking for the response anymore).
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Read fseq info from FW registers and print it upon fw assert.
The print is needed since the fseq version coming from the TLV might
not be the actual version that is used.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we have a single image (same firmware image for INIT and
OPERATIONAL), we couldn't load the driver and register to the
stack if we had hardware RF-Kill asserted.
Fix this. This required a few changes:
1) Run the firmware as part of the INIT phase even if its
ucode_type is not IWL_UCODE_INIT.
2) Send the commands that are sent to the unified image in
INIT flow even in RF-Kill.
3) Don't ask the transport to stop the hardware upon RF-Kill
interrupt if the RF-Kill is asserted.
4) Allow the RF-Kill interrupt to take us out of L1A so that
the RF-Kill interrupt will be received by the host (to
enable the radio).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This debugfs file is really old, and cannot work properly since
the unified image support. Rather than trying to make it work,
which is difficult now due to multiple images (LMAC/UMAC etc.)
just remove it - we no longer need it since we properly do a FW
coredump even in D3 cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJczDAZAAoJEG4XJFUm622blLgH/jdBKEq9i1m5dtLi48u4sgPV
NsnPhR5XQjpbYpmvgPslKLxWzZq6A0P+lo9QqTXkP/QRyJLu7RnoY1c2wVsQbWaK
VTXc0cROzWt0ihAt8Mc/rEsZpISVnQ9mJbTd/kSJM9WlDeIg0jcJvnEAdQiEmM5t
2t+zZ5CupUXYbGE3zWHL1GSjBD9f0v7zyrNxYNGfvqhDEXhTFWAmVuRtfoAVlRU+
dt1HMv+qdxgoF6Uvaw/kgY09mDvdrfy2EVL0q7S3TKceute60SWf7de2sToI/rMQ
snUnVqTIIUnWPl6g+C3Bp2TbdZhy6XCSRsMFOVa2i1Lt+z1qe3dTr3hjxTQWRhE=
=uLaP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows to configure a periodic data collection
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Don't use cancel_delayed_work_sync() inside the channel switch
notifications as they are handled synchronously as part of the RX path.
Fix that by replacing it with cancel_delayed_work(). This should be safe
as we don't really care whether the work is already started and in such
case we would disconnect anyway.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the TLC config command according to the
rates the peer supports, make sure that we aren't also
limited by our own rates, so take the minimum between the
peer's supported RX rates and our supported TX rates.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the interface that is requesting an FTM measurement is connected
to a BSS, it is possible that the FTM request was originated by an
RRM request from the AP. In this case the station needs to report
the measurement start time in terms of the TSF of the AP.
Since there is no indication in the FTM request itself if the TSF
is needed, always report the TSF if the station is associated.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new definitions for the WoWLAN patterns API version 2 and support
for version 2 of the WoWLAN patterns command without implementing the
new features. With this commit we only supporting the existing
bitmask pattern match. Use the new version only if the TLV is set.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When I rebased Greg's patch, I accidentally left the old if block that
was already there. Remove it.
Fixes: 154d4899e4 ("iwlwifi: mvm: properly check debugfs dentry before using it")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't check for the validity of the lengths in the packet received
from the firmware. If the MPDU length received in the rx descriptor
is too short to contain the header length and the crypt length
together, we may end up trying to copy a negative number of bytes
(headlen - hdrlen < 0) which will underflow and cause us to try to
copy a huge amount of data. This causes oopses such as this one:
BUG: unable to handle kernel paging request at ffff896be2970000
PGD 5e201067 P4D 5e201067 PUD 5e205067 PMD 16110d063 PTE 8000000162970161
Oops: 0003 [#1] PREEMPT SMP NOPTI
CPU: 2 PID: 1824 Comm: irq/134-iwlwifi Not tainted 4.19.33-04308-geea41cf4930f #1
Hardware name: [...]
RIP: 0010:memcpy_erms+0x6/0x10
Code: 90 90 90 90 eb 1e 0f 1f 00 48 89 f8 48 89 d1 48 c1 e9 03 83 e2 07 f3 48 a5 89 d1 f3 a4 c3 66 0f 1f 44 00 00 48 89 f8 48 89 d1 <f3> a4 c3
0f 1f 80 00 00 00 00 48 89 f8 48 83 fa 20 72 7e 40 38 fe
RSP: 0018:ffffa4630196fc60 EFLAGS: 00010287
RAX: ffff896be2924618 RBX: ffff896bc8ecc600 RCX: 00000000fffb4610
RDX: 00000000fffffff8 RSI: ffff896a835e2a38 RDI: ffff896be2970000
RBP: ffffa4630196fd30 R08: ffff896bc8ecc600 R09: ffff896a83597000
R10: ffff896bd6998400 R11: 000000000200407f R12: ffff896a83597050
R13: 00000000fffffff8 R14: 0000000000000010 R15: ffff896a83597038
FS: 0000000000000000(0000) GS:ffff896be8280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff896be2970000 CR3: 000000005dc12002 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
iwl_mvm_rx_mpdu_mq+0xb51/0x121b [iwlmvm]
iwl_pcie_rx_handle+0x58c/0xa89 [iwlwifi]
iwl_pcie_irq_rx_msix_handler+0xd9/0x12a [iwlwifi]
irq_thread_fn+0x24/0x49
irq_thread+0xb0/0x122
kthread+0x138/0x140
ret_from_fork+0x1f/0x40
Fix that by checking the lengths for correctness and trigger a warning
to show that we have received wrong data.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/net/wireless/intel/iwlwifi/mvm/sta.c:2114:12: warning: variable
'queue' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
Clang can't evaluate at this point that WARN(1, ...) always returns true
because __ret_warn_on is defined as !!(condition), which isn't
immediately evaluated as 1. Change this branch to else so that it's
clear to Clang that we intend to bail out here.
Link: https://github.com/ClangBuiltLinux/linux/issues/399
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[added a few more braces]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The range response notification API has changed to add a value that
indicates the confidence of the rtt result.
Support the new API and print the rtt confidence for debug.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When building TLC configuration command, consider in case of HE,
if LDPC support is turned on in our capabilities.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AX210 devices support 256 BA (256 MPDUs in an AMPDU).
The firmware requires that the number of TFDs will be
minimum twice as big as the BA size (2 * 256 = 512).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcuHgsAAoJEG4XJFUm622bfo8H/3uRRxsQBHGg6e3NpELaxpNV
IfrPDtvxyfILzIepBBhnZYUY0OrlTHKfMmzFBD9FFMojsxBYddnLZ/0iKUNKfwLm
KzToW/64YJ784dc+tw85gjh8I3MB+RRoD0l01M1HuOkzQ4hDNEGK3IsMHsBs/oTZ
huiqTYsTxStOj53vOpQiBFZ1pYBtvGLMxBdSepDcR27bgT1gwriynCSkSNglDH8z
/t3m6hDGtZa6uVkoIVH+BAMu6+vt+vIkU/TOdmiW/zqBL2JYq6cDE0uIb3bLAzN6
uvS1Rj42P3OwHUwFavlUBdr5Rdcj6P24S5ZhtVaGGWCBjMZI5/nO7IjzwyQnQuQ=
=/6q9
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
debugfs can now report an error code if something went wrong instead of
just NULL. So if the return value is to be used as a "real" dentry, it
needs to be checked if it is an error before dereferencing it.
This is now happening because of ff9fb72bc0 ("debugfs: return error
values, not NULL"). If multiple iwlwifi devices are in the system, this
can cause problems when the driver attempts to create the main debugfs
directory again. Later on in the code we fail horribly by trying to
dereference a pointer that is an error value.
Reported-by: Laura Abbott <labbott@redhat.com>
Reported-by: Gabriel Ramirez <gabriello.ramirez@gmail.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: stable <stable@vger.kernel.org> # 5.0
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we fail to initialize because rfkill is enabled, then trying
to do debug collection currently just fails. Prevent that in the
high-level code, although we should probably also fix the lower
level code to do things more carefully.
It's not 100% clear that it fixes this commit, as the original
dump code at the time might've been more careful. In any case,
we don't really need to dump anything in this expected scenario.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 7125648074 ("iwlwifi: add fw dump upon RT ucode start failure")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support API change to pass all mbssid parameters to the firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The device time register address has changed for 22000 devices.
Add a util function for getting the GP2 time and use the correct
register address depending on the device family.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After converting the driver to TXQs, it no longer has any reason
to initialize vif->hw_queue/vif->cab_queue since it no longer sets
the HW_QUEUE_CONTROL flag. Remove the code that initialized those,
it was broken due to relying on an uninitialized stack value in
used_hw_queues, as Colin reported.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pointer referencing when setting HE QAM thresholds (when nominal
packet padding bit is on) caused kernel crash due to bad
referencing. Fix that.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Back in commit 4d339989ac ("iwlwifi: mvm: support ibss in dqa mode")
we changed queue selection for IBSS to be:
if (ieee80211_is_probe_resp(fc) || ieee80211_is_auth(fc) ||
ieee80211_is_deauth(fc))
return IWL_MVM_DQA_AP_PROBE_RESP_QUEUE;
if (info->hw_queue == info->control.vif->cab_queue)
return info->hw_queue;
return IWL_MVM_DQA_AP_PROBE_RESP_QUEUE;
Clearly, the thought at the time must've been that mac80211 will
select the hw_queue as the cab_queue, so that we'll return and use
that, where we store the multicast queue for IBSS. This, however,
isn't true because mac80211 doesn't implement powersave for IBSS
and thus selects the normal IBSS interface AC queue (best effort).
This therefore always used the probe response queue, which maps to
the BE FIFO.
In commit cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
we rethought this code, and as a consequence now started mapping the
multicast traffic to the multicast hardware queue since we no longer
relied on mac80211 selecting the queue, doing it ourselves instead.
This queue is mapped to the MCAST FIFO. however, this isn't actually
enabled/controlled by the firmware in IBSS mode because we don't
implement powersave, and frames from this queue can never go out in
this case.
Therefore, we got queue hang reports such as
https://bugzilla.kernel.org/show_bug.cgi?id=201707
Fix this by mapping the multicast queue to the BE FIFO in IBSS so
that all the frames can go out.
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Differentiate between SW and HW error interrupts and support ini HW
error trigger.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With offloaded rate control, if the station parameters (rates, NSS,
bandwidth) change (sta_rc_update method), call iwl_mvm_rs_rate_init()
to propagate those change to the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_tx_mpdu() may run from iwl_mvm_add_new_dqa_stream_wk(), where
soft-IRQs aren't disabled. In this case, it may hold the station lock
and be interrupted by a soft-IRQ that also wants to acquire said lock,
leading to a deadlock.
Fix it by disabling soft-IRQs in iwl_mvm_add_new_dqa_stream_wk().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Send NO_DATA events so they can be captured in radiotap;
* Some channel-switch changes;
* Support for multiple BSSID;
* Continued work and bugfixes for the new debugging infra;
* Support for some new FW API versions;
* Some work to support new hardware;
* General bugfixes;
* Other cleanups;
-----BEGIN PGP SIGNATURE-----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=wFO2
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2019-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of patches intended for v5.2
* Send NO_DATA events so they can be captured in radiotap;
* Some channel-switch changes;
* Support for multiple BSSID;
* Continued work and bugfixes for the new debugging infra;
* Support for some new FW API versions;
* Some work to support new hardware;
* General bugfixes;
* Other cleanups;
Separate between ini and legacy dump flows to allow adding ini triggers
that are not supported in the legacy flow and to increase readabilty.
iwl_fw_dbg_ini_collect function is now called with legacy trigger id and
_iwl_fw_dbg_ini_collect is called with ini trigger id.
Also make the actual dumping function static so that any dump collection
will go through iwl_fw_dbg_collect_sync.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mac80211 sets max amsdu to min supported ht vs vht but TLC only works
with one mode so we can set to the exact mode used (vht/ht)
and enable larger amsdu sizes for vht.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In restart flow, the driver requests HW restart from mac80211
and then mac80211 uses a worker to do the restart flow. In that flow a
sync dump is performed. Instead, schedule the dump worker before
requesting HW restart from mac80211. This approach simplifies the
restart flow.
Also, it is neeeded in order to differentiate between the handling of SW
and HW errors in a future commit.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer FWs use a new format of the SCAN_OFFLOAD_PROFILES_QUERY_RSP,
which now supports indicating match on an higher number of channels.
Modify the code to support both the old format and the newer one,
based on a FW TLV.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If number of channels in the driver is greater than
number of scan channels given by firmware TLV, do not
fail scan config, but adjust to firmware's number of channels.
This is helpful for supporting in driver new channels before
it being supported by firmware scan.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For some reason we never enabled it, but it appears to work fine.
Enable it now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the capabilities flags and inform firmware
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some buggy APs that keeps changing the count while forcing
us to block TX. This eventually results in queue hang, assert, and
disconnection. Detect such APs and disconnect gracefully in advance.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we receive channel switch announcement with immediate
quiet and unknown switching time, we will switch when FW identifies
AP left channel. However, if AP remains on channel, we will
eventually get TX queue hang. Init a work to disconnect if
switch doesn't occur within 1500 milliseconds. Do it also
for a too long channel switch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Let FW know if quiet mode is on or not. This is needed
in order to disable it in FW when CSA is complete.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Send to FW modify command for every beacon we receive during channel
switch. FW will track the count, and make sure the event is scheduled
in time even if AP changed count.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Report all NO_DATA events to mac80211 so they get captured
in radiotap for usage in sniffer scenarios; map the info
type to a reasonable radiotap type for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we receive abort operation for CSA, clean up
our state.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support passing to FW delayed beacon count. This
represents the delay the AP can have when moving to
the new channel.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the old days, we could transmit with HW crypto with an arbitrary
key by filling it into TX_CMD. This was broken first with the advent
of CCMP/GCMP-256 keys which don't fit there.
This was broken *again* with the newer TX_CMD format on 22560+,
where we simply cannot pass key material anymore. However, we forgot
to update all the cases when we get a key from mac80211 and don't
program it into the hardware but still return 0 for HW crypto on TX.
In AP mode with WEP, we tried to fix this by programming the keys
separately for each station later, but this ultimately turns out to
be buggy, for example now it leaks memory when we have more than one
WEP key.
Fix this by simply using only SW crypto for WEP in newer devices by
returning -EOPNOTSUPP instead of trying to program WEP keys later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
do_div() expects unsigned operands and otherwise triggers a warning like:
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:465:2: error: comparison of distinct pointer types ('typeof ((rtt_avg)) *' (aka 'long long *') and 'uint64_t *' (aka 'unsigned long long *')) [-Werror,-Wcompare-distinct-pointer-types]
do_div(rtt_avg, 6666);
^~~~~~~~~~~~~~~~~~~~~
include/asm-generic/div64.h:222:28: note: expanded from macro 'do_div'
(void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
~~~~~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~
1 error generated.
Change the do_div() to the simpler div_s64() that can handle
negative inputs correctly.
Fixes: 937b10c0de ("iwlwifi: mvm: add debug prints for FTM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJccAnlAAoJEG4XJFUm622bxxMH/2cz2GEuDQXOwfYLnCUwFES8
vqTdMWnlfqGQvsTyvtSp91KqsL3hE2FB1Cu3n6/vzND3C7afT0V2/QlU7Pmgr8sR
1gnJnu0NJT5SZfzcTsqwt8rFw9lQZ3HcvEcfNo6T5KUyyY7FGCNGR5H27nvoKOP3
ea1h7U80loPV40sGTI8jj963wa9LNHUrjHTK4wY+KMWECgZuD/fHeE9YPB9MTdff
lJ5bWCoQmuJddvTtC+X0tOAsCkxgdbbw6ieKqzep8H4gtUjerZD+V8uUdbtpr7IL
sWPoaqrrADMv9cZtDVj+pEtNIJ3mpfuHYFKSON9jy/uxygeFTfVzLu43RFreDp8=
=D15/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net-next to resolve a conflict and to get the mac80211
rhashtable fixes so further patches can be applied on top.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update element names and new fields according to D3.3 of
the HE spec.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For non-offloaded rate control, implement VHT extended NSS
support by just ignoring 160 MHz on transmit if the peer
doesn't support the full NSS (2). This is pretty unlikely
and gets us 160 MHz RX as well as TX in most cases, since
the typical case for this workaround is 4x4 AP only doing
2x2 on 160 MHz.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When hostapd sends a probe response, it does not request an
acknowledgment on the probe response. This setting is propagated
to the driver and FW from mac80211, and as a result probe responses
are transmitted only once without retries. In congested
environments, this reduces the likelihood for finding the AP.
To overcome this, enable acknowledgment and retries for probe
responses, even in case no acknowledgment is requested. In such
a case the retry limit is set to 3.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in this, we already do everything in a nested
fashion, and if we didn't we'd already crash in iwl_mvm_leds_exit()
etc. Just remove the bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Previously the protection flag wasn't set on multicast frames even if
the RA is unicast. Fix this by checking addr1 instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add an option to not send beacons and probe responses. This is
used for testing multiple-bssid.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Return the AID currently set when reading this debugfs entry.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Verify we do not accept new beacon templates while beacon
injection is active.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The IWL_MVM_INIT_STATUS_REG_HW_INIT_COMPLETE bit shouldn't be set,
and realistically we should complete all setup before we call the
ieee80211_register_hw() function. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With CONFIG_NO_AUTO_INLINE, we run into a silly warning when
gcc fails to remember that n_profiles is constant across
the function call to iwl_mvm_sar_set_profile:
drivers/net/wireless/intel/iwlwifi/mvm/fw.c: In function 'iwl_mvm_sar_get_ewrd_table':
drivers/net/wireless/intel/iwlwifi/mvm/fw.c:746:9: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Marking that function 'inline' avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case mac80211 was requested to perform an HW restart, but the HW
restart has not started yet, there is no need to request another one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AP interfaces still use some static TX queues (for probes,
broadcast and multicast frames). These queues were not stopped
correctly when the transport layer indicated the queue should be
stopped. As a result, when flushing the queues, new frames from
the overflow queue were tx'd, so the queues still had frames after
flushing. This ended up in an assert since trying to remove a station
with non-empty queues.
Fix it by stopping the static queues correctly when required.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add IWL_FW_INI_APPLY_EARLY and IWL_FW_INI_APPLY_AFTER_ALIVE apply points
to unified images.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When HW restart is requested but not started yet, commands would not
be sent to the FW, and some function calls would return an error. In
case of iwl_mvm_mac_sta_state() returning an error value when a
station is removed can lead to an unneeded warning in
__sta_info_destroy_part2().
Handle this by setting the return value to 0, in case HW restart is
in progress.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When HW restart is requested but not started yet, commands would not
be sent to the FW, and some function calls return an error. Such cases
can trigger unneeded warning messages, e.g., in iwl_mvm_mac_sta_state()
and iwl_mvm_bss_info_changed_station().
Handle a couple of these cases by also checking in the WARN_ON()
condition that HW restart is not requested.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The spatial reuse 4 words fields are fetched from the HE-SIGA
by the firmware and propagated to the driver through the
Rx info. This is useful to populate the radiotap header.
We were looking at the wrong place in the firmware data and
got bogus values. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: bdf180c8d3 ("iwlwifi: mvm: change PHY data RX for HE radiotap")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debug prints for FTM results info. These prints are used by
tests automation.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In HE-TB PPDUs (labeled HE-TRIG in radiotap), we were overwriting
the data4.spatial_reuse_1 field with the spatial reuse data that
the firmware gives us for SU/MU PPDUs. Fix that by moving that,
we are already setting the data4.spatial_reuse_{1,2,3,4} fields
in the TB PPDU case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 69f3ca8ed3 ("iwlwifi: mvm: show more HE radiotap data for TB PPDUs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FTM new API uses API TLV bit 15. The driver mistakenly uses
this bit for beacon filter API, although no TLV was assigned for
the beacon filter API. For now, make beacon filter use bit 16
instead (not set by the fw anyway). Once a TLV is assigned to the
beacon filter API it should be updated.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- The FW supports up to 4 concurrent scans, so adjust the definitions
accordingly.
- Only a single periodic scan is supported, so enforce it in the code.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
D3 debug data is disabled by default. Currently it is done by tampering
the dump mask. Add an operation that will allow this to be changed
without recompilation.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AX210 family, UMAC periphery address space moved from
0xA00000 to 0xD00000.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In low power modes, the chip clock source for platform integrated
devices is 32kHz. It is generated internally and supplied by a crystal
oscillator. However using a 32kHz sourced from crystal oscillator
has high power penalty.
There is an option to get an external 32kHz clock from the platform. Past
experience shows that the reliability is platform dependent,
i.e. on some platforms it works good and on other it doesn’t.
Working from external clock will save 0.5 mW in sleep state, from overall
1.8mW that we have today, i.e. almost 30%.
Each OEM can enable or disable the use of the external 32kHz clock by
setting a BIOS configuration. In case the OEM configured to use 32kHz
external clock the driver will pass this indication to the FW.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_te_clear_data() is called for cleanup in case sending
the HOT_SPOT_CMD failed. However, in case sending the command
caused a fw error and restart (e.g. if the command is not supported)
then the te_data pointer may no longer be valid, which leads to
a NULL pointer dereference.
Fix it by checking that the te_data pointer is not NULL before
dereferencing it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new API and TLV for the ability to send commands in the beginning
and end of reset flow.
The full flow of recovery is:
1. While loading FW, get address (from the TLV) of target buffer
to read in case of reset
2. If an error/assert happens read the address data from step 1.
3. Reset the HW and load the FW.
4. Send the data read in step 2.
5. Add station keys
6. Send notification to FW that reset flow is done.
The main use of the recovery flow is for support in PN/SN recovery
when offloaded
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new device family AX210.
Make the needed changes for this family.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TLV 54 holds umac debug related addresses.
TLV 55 holds lmac debug related addresses.
These TLVs aim to replace the alive notification data in the future.
Parse and keep error table addresses received from the TLVs
for both lmac and umac and use these addresses instead of the pointer
received from alive notification.
The feature supports only unified image.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We now no longer have any special code in
iwl_mvm_pass_packet_to_mac80211(), so don't
need to pass NO_PSDU packets through it.
Stop doing so and clean up the code there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.
Additionally, add two defines we depend on in
include/linux/ieee80211.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for FTM responder for hardware/firmware combinations
that advertise support for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
WOWLAN images in unified firmwares should not be used, so don't require
them to support wowlan. This will allow to reduce the firmware's file
size.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have >=10 (logical) CPUs, our command size exceeds the
internal buffer size and the command fails; fix that by using
IWL_HCMD_DFL_NOCOPY for the command that's allocated anyway.
While at it, also fix the leak of cmd, and use struct_size()
to calculate its size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 8edbfaa198 ("iwlwifi: mvm: configure multi RX queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The typical sequence of setting INIT_DONE and then waiting
for clock stabilisation is going to need a new workarounds,
so first of all refactor it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The hash mask is a bitmap, so we should use BIT() on
the enum values.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 43413a975d ("iwlwifi: mvm: support rss queues configuration command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update iwl_beacon_filter_cmd to support
BEACON_FILTER_CONFIG_API_S_VER_4.
Currently driver configs them to be zero
(i.e. disable them, so no change is applied).
Signed-off-by: Avigail Grinstein <avigail.grinstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Hiding the HE radiotap data for further processing of the SKB just
caused another bug when adding the L-SIG data. Simply stop doing
this and adjust the skb->data pointer accordingly when we need to
get the 802.11 header.
While at it, also verify and fix the data alignment, we need to add
2 bytes padding with the vendor data to ensure the whole length of
all radiotap headers is a multiple of 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6721039d5b ("iwlwifi: mvm: add L-SIG length to radiotap")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Depending on exactly what happens in the FW, an invalid host-command
could result in either assert 0x38 or 0x39. Add 0x39 to the assert-name
table.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Expose the trigger-based PPDU SIG-A bandwidth to radiotap in
the newly defined bits thereof.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have a station connecting HE, make sure that the
MAC ctxt is updated with indication of this before
setting the TLC rates via the TLC manager command.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of having the command appear as "UNKNOWN" in the
dmesg, add the name to it.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_mvm_sta_alloc_queue_tvqm(), we know that we have a
station, so no need to check it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Typically, when not in HE mode, we will not perform well
with AMSDUs bigger than 8K.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently we started to send the WEP keys to the firmware so
that we could use hardware Tx encryption also on newer
devices that require the keys to be installed in the firmware
for encryption (as opposed to older devices that can get
the key in the Tx command for each Tx).
When we implemented that, we forgot to remove the key when
we remove a station leading to a situation where a station
that connects and disconnects a lot of times exhausts the
key database inside the firmware.
A fix was made for that, but we always removed the same
key: mvmvif->ap_wep_key which means that we removed the
same key entry in the firmware. This can make sense since
in WEP, the key is the same for all the stations, but the
internal implementation of iwl_mvm_set_sta_key and
iwl_mvm_remove_sta_key assumes that each station uses a
different key in the firmware's key database.
So now we got to the situation where we have a single
ieee80211_key_conf instance that means, a single
ieee80211_key_conf.hw_key_idx index for several stations
and hence for several keys.
ieee80211_key_conf.hw_key_idx is set to 0 when the first
station associates, and then it is overwritten to 1 when
the second station associates which is a buggy of course.
This led to the following message upon the removal of the
second station:
iwlwifi 0000:00:03.0: offset 1 not used in fw key table.
WARNING: CPU: 2 PID: 27883 at net/mac80211/sta_info.c:1122 __sta_info_destroy_part2+0x16b/0x180 [mac80211]
RIP: 0010:__sta_info_destroy_part2+0x16b/0x180 [mac80211]
Call Trace:
__sta_info_destroy+0x2a/0x40 [mac80211]
sta_info_destroy_addr_bss+0x38/0x60 [mac80211]
ieee80211_del_station+0x1d/0x30 [mac80211]
nl80211_del_station+0xe0/0x1f0 [cfg80211]
Fix this by copying the ieee80211_key_conf structure for
each and every station. This is the easiest way to properly
remove the keys with the right index. Another solution
would have been to allow several stations to use the same
key offset in the firmware. That would require to change
the way we track keys in iwlmvm and not really worth it.
Also, maintain correctly fw_key_table when we add a key
for the multicast station.
Remove the key when we remove the multicast station.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 337bfc9881 ("iwlwifi: mvm: set wep key for all stations in soft ap mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some switch-cases were missing a fall through comment, so the compiler
may warn. Fix that by adding the comments where needed. In other
cases there was more text in the comment, which the compiler doesn't
recognize, so either remove the extra text or move it to a separate
comment line as appropriate.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several dumping flows in the driver in case of a fail
prior to operational.
In some cases we get 2 dumps while in others we get none.
Fix this by uniting the different flows.
Add a different dump type to driver triggered dumps in case we want
a dump but did not got assert, and make all dumping go through
iwl_fw_dbg_collect_desc to avoid multiple dumps.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware is changing the format of the beacon
notification to remove the dependency on the Tx response
format.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are two cases that can cause the alive flow to fail,
an assert or a timeout.
Currently we mask any incoming asserts when we wait for alive.
Solve this by differentiating between the two cases:
1. Let the regular error handling to handle a received assert
2. Do a dump collection in the case of a timeout
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: f38efdb293 ("iwlwifi: add dump collection in case alive flow fails")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we do channel switch, we used to schedule time events
ourselves. This was offloaded to FW. Support the new command
and flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Simplify some return conditions found by running a semantic patch
to detect unnecessary assignments to local variables.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
I also removed one header search path in:
drivers/net/wireless/broadcom/brcm80211/brcmutil/Makefile
I was able to compile without it.
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A call to iwl_mvm_add_rtap_sniffer_config() was missing due to a merge
damage when I submitted the patch mentioned below. And this causes
the following compilation warning:
drivers/net/wireless/intel/iwlwifi/mvm/rxmq.c:195:13: warning: 'iwl_mvm_add_rtap_sniffer_config' defined but not used [-Wunused-function]
static void iwl_mvm_add_rtap_sniffer_config(struct iwl_mvm *mvm,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it by adding the if block that calls this function.
Fixes: 9bf13bee2d ("iwlwifi: mvm: include configured sniffer AID in radiotap")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When MU EDCA params change, resend the STA_HE_CTXT command
updating the MU EDCA params.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the regular flow, when we receive an assert, ieee80211_reconfig is
called which reconfig the driver using iwl_mvm_mac_start.
iwl_mvm_mac_start is clearing the restart bit and does dump collection.
Prior to setting the device up, ieee80211_reconfig does not call
iwl_mvm_mac_start since there is nothing to reconfig and we miss the
dump collection of the assert.
solve it by checking the restart bit before we stop the device
and trigger a dump collection in case it is set.
note that we don't need to do it in the fmac case since in fmac
assert flow in iwl_fmac_nic_error we call iwl_fw_dbg_collect_desc
so we can be sure that there will a dump collection in
iwl_fmac_stop_device.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to make more sense out of the captured radiotap data e.g.
when the configured AID changes, add the currently configured AID
to the radiotap data as a vendor extension field.
This is made race-free by updating the included value from inside
the RX path (using a notification wait) for the command response
from the firmware, which thus means it's serialized with frame RX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The reorder buffer is bypassed because the firmware won't have
any BA sessions, document this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We introduce a new state for latency, force mode, in force mode
you can enable always to be in low latency or always to be in non
low latency.
This is required for test mode in max TpT test.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We maintain a timer for each Tx queue to detect stalls and
be able to recover / debug.
When we work in AP mode, we can freeze the Tx queue timer if
a station goes to sleep, because we don't want to warn about
stalls that are caused by faulty clients that don't wake up
on time.
This mechanism was applied to the queues of the clients, but
the management queue was omitted. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change iwl_fw_channel_info structure so it can have channel number
greater than 255. This is needed for 6 GHz channel numbers.
Change all relevant structs and member accesses accordingly.
The new API is indicated by a TLV capability bit.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement CSI (channel estimation matrix) reporting in the mvm
driver, if the firmware has the capability.
Currently only a debugfs API is provided as the API is still
under discussion.
For now, RX aggregation must be disabled to use this feature
on data frames as we haven't found a good way to attach the
data to A-MPDUs, given complexities with multi-queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the location/time-of-flight/FTM APIs that we'll use in
follow-up patches to implement FTM responder and initiator.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some buggy APs stop sending beacons, but continue to ack our null data
packets or even run some traffic. It's better not to stick connected to
such an AP forever, so disconnect after some larger beacon loss
threshold is crossed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is an ancient (~2015) implementation that no longer matches
the firmware in any way, and most likely never worked. Remove all
of it so it can be reintroduced properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TX path lock was introduced in order to prevent out of order
invocations of TX.
This can happen in the following flow:
TX path invoked from net dev
Packet dequeued
TX path invoked from RX path
Packet dequeued
Packet TXed
Packet TXed
However, we don't really need a lock. If TX path is already
invoked from some location, other paths can simply abort their
execution, instead of waiting to the first path to finish, and
then discover queue is (likely) empty or stopped.
Replace the lock with an atomic variable to track TX ownership.
This simplifies the locking dependencies between RX and TX paths,
and should improve performance.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current code assigns the reference, and then goes to increment
it if the toggle bit has changed. That way, we get
Toggle 0 0 0 0 1 1 1 1
ID 1 1 1 1 1 2 2 2
Fix that by assigning the post-toggle ID to get
Toggle 0 0 0 0 1 1 1 1
ID 1 1 1 1 2 2 2 2
Reported-by: Danny Alexander <danny.alexander@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: fbe4112791 ("iwlwifi: mvm: update mpdu metadata API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently whenever we get firmware notification with mac id,
we iterate over all the interfaces to find the ID. This is a
bit cumbersome. Instead, adding an array of RCU pointers, like
we have for station IDs. This is not expensive space wise
since we have only up to 4 active MACs, and not complicated
code wise, since we have a clear point to init and de-init it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If WEP is used, no one removes the STA key upon STA
removal, leading to a situation where after 16
connect/disconnects - the AP could no longer decrypt
incoming data frames since iwl_mvm_set_fw_key_idx()
called from iwl_mvm_set_sta_key() during association
returns STA_KEY_IDX_INVALID, thus not setting the key
for that connecting STA.
Fix this by removing the key in the driver when the
STA is removed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The function we pass to the wait alive notification procedure may may
not even get called if the timeout occurs before the function is
called. To prevent accessing unitialized data in alive_data, pre-set
it to zero in the declaration. Found by static analyzers.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These inlines just check the module parameters, so they don't
need a configuration parameter and can move to a better place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes we want to debug issues related to the regulatory blob in
the NVM. To make that easier, add a debugfs entry to export it
together with the other nvm blobs we export.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Clean up the LDBG config command to not be called "continuous
recording", and while at it actually remove the continuous
recording implementation completely since it was only used for
store & forward architectures.
This also fixes a bug at least in iwl_fw_dbg_buffer_allocation()
because what's now "__le32 type" (matching the firmware) used to
be "__le16 enable_recording", so the buffer allocation config
sub-struct would erroneously have started at the wrong offset.
In the other cases this didn't actually lead to a bug as other
bytes in pad[] were all zeroes, so accessing the 16-bit value as
a 32-bit value wouldn't make a difference (in little endian.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to a general shortage of RX API bits, the firmware is going
to reuse this bit on non-CCK frames to mean something else. Use
it only on CCK frames to prepare for that change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With just %16, it means 16 characters padding, but we really
don't want to print "0x 1F4547B", but instead want to
have this filled with zeroes, so we need the 0.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Take the NSS value from 'rx_vec' rather than from 'rate_n_flags'.
The rate_n_flags has only 2 bits for the NSS giving a max of 4SS
(0 = 1SS etc.). Since there may be up to 8SS use the rx_vec which
has 3 bits for the NSS.
While at it, fix the rx_vec array to length of 2.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When setting the EOF bit in Rx flags (propagated
to radiotap) do not depend it on the PPDU type (SU/MU/TB)
since it doesn't.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value in txq_id can be out of array scope,
validate it before accessing the array.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver assumes certain sizes and lengths aren't crossed in some
places. Make sure this indeed happens.
Found by Klocwork.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is no point in having num_active_macs signed
since it should never be negative. Set it to be an
unsigned variable to ensure this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As this is not needed and might cause interoperability issues
during pairing with devices that would not reply to RTS frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a frame is transmitted without a station, need to set the rate
and flags in the Tx command, as the FW does not have any information as
to what rate and flags should be used for this frame.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a time event for a P2P Device interface is done, it is possible
that there is still a frame pending for transmission that should be
flushed.
Set the IWL_MVM_STATUS_NEED_FLUSH_P2P to indicate to the ROC worker
that P2P Device station queue need also to be flushed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have a slightly better TCP performance with GSO.
Add it back, it can co-exist with the code that builds
AMSDUs in mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We erroneously had some values for NGI in the table we give as an
example in rs_fill_rates_for_column(), when they should be SGI.
Change them so that they match what we say.
Reported-by: Rémy Grünblatt <remy@grunblatt.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support getting mac80211 building AMSDUs for us. Remove GSO
support from mvm - we don't need it anymore.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move to use the new mac80211 TXQs implementation. This has
quite a few benefits for us. We can get rid of the awkward
mapping of DQA to mac80211 queues. We can stop buffering
traffic while waiting for the queue to be allocated. We can
also use mac80211 AMSDUs instead of building it ourselves.
The usage is pretty simple:
Each ieee80211_txq contains iwl_mvm_txq. There is such a
queue for each TID, and one for management frames. We keep
having static AP queues for probes and non-bufferable MMPDUs,
along with broadcast and multicast queues. Those are being
used from the "old" TX invocation path - iwl_mvm_mac_tx.
When there is a new frame in a TXQ, iwl_mvm_mac_wake_tx is
being called, and either invokes the TX path, or allocates
the queue if it does not exist.
Most of the TX path is left untouched, although we can consider
cleaning it up some more, for example get rid of the duplication
of txq_id in both iwl_mvm_txq and iwl_mvm_dqa_txq_info.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On any failure, including if we crash the firmware or get garbage
data, we currently ignore this and pretend the OTP was empty.
Clearly, this isn't typically the case.
In cases other than the firmware saying it can't read the requested
section, or the section having ended, make the access actually fail
and trickle the error up through the layers to fail init.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new (CDB) statistics API is used by non-CDB devices
as well. Look at the right TLV flag to know which version
of the statistics notification to use.
To avoid confusion, remove the _cdb suffix from the
structure name.
While at it, remove a structure that was never used.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 678d9b6ddd ("iwlwifi: mvm: update rx statistics cmd api")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When configuring TLC DCM flag:
1. check the peer's RX DCM capabilities (since we TX)
2. do not set DCM_NSS_2 since we do not support it
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Fixes: 423584dd80 ("iwlwifi: rs-fw: support dcm")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mac80211 will check both the HE Capability IE and the
Extended Capability IE, so set the TWT support bit when
mac80211 tells us to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to advertise support for TWT in the Extended
Capability IE. Since we don't want to set the bits for all
the interface types, define an interface specific
configuration.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add to the dump the number of lmacs, the error id of the umac
and the error id of lmac1, if supported.
In case the reason for the dump trigger is not an assert
the error id is zero.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the rt status of the last assert or 0 if the dump collection was
not initiated by an assert. Add the number of rx and tx fifos in use.
These fields are added to dump info lst file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes, due to SCD bug, we need to start the queue with an
higher SSN. The queue allocation function currently increments
the SSN in the packet itself, but it is pointless, since this
value is overridden later by iwl_mvm_tx_mpdu with the value
from mvmsta->tid_data[tid].seq_number. Updating tid data is
sufficient.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to lock mvm station for transport reclaim.
Move the locking down, after the reclaim.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handle RX no data notification, which is used for advertising NDP to
radiotap.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FW expects to get the ppe value for each NSS-BW pair in the same
format as in the he phy capabilities IE, which means that a value of 0
implies ppe should be used for BPSK (mcs 0). If there are no PPE
thresholds in the IE, or if for some NSS-RU pair there's no threshold
set for it (this could happen because it's a variable-sized field), it
means no PPE should not be used for that pair, so the value sent to FW
should be 7 which corresponds to "none".
Fixes: 514c30696f ("iwlwifi: add support for IEEE802.11ax")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the coupling of station id and queue id clear. Group code
together. Remove outdated comment. Never use an undefined hw
queue as given from mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Assigning mvmsta to be NULL when we are about to exit the
function is pointless. Remove it. Move the variable declaration
to the scope it is used.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In iwl_mvm_tx_skb_non_sta(), in case of managed interface,
the AP station was supposed to be used for multicast frames
instead of the auxiliary station to avoid frames possibly
sent to an absent P2P GO. However, when moving to DQA mode,
this was broken as no valid queue was assigned. This is fixed
by a recent patch that directs all non-offchannel traffic to
ap station earlier in the TX path. However, the broken, and
now dead code, remained. Remove it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Old firmware versions don't support this command. Sending it
to any firmware before -41.ucode will crash the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201975
Fixes: 66e839030f ("iwlwifi: fix wrong WGDS_WIFI_DATA_SIZE")
CC: <stable@vger.kernel.org> #4.19+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We used to have many versions of statistics notification
coming from the firmware. In one of the cleanup patches,
we forgot to clean the code that checks if data->general
is set. Since it is always set, remove the check.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
UL_DL is irrelevant to HE TRIG_BASED PPDU.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We may have the L-SIG length depending on the phy_data info type;
add it to radiotap when we do.
Move getting the phy_data out one layer up and the info type into
it so we can use this data more generically. We need to call the
iwl_mvm_rx_he() function for other reasons as well, so can't just
combine all of that into something like iwl_mvm_parse_phy_data().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware changed the PHY data API, so follow suit.
Some data is now available even for HT/VHT frames, so
the info type in the metadata was changed. This change
isn't backwards compatible, but
1) the firmware with the old API was never released;
2) the only overlap in the info type field is from the
old type of TB to the new of HT, so this basically
just means that with older FW and newer driver the
data will be considered missing.
While at it, remove the extra code to set the LTF syms
corresponding to the streams and use the data from the
device instead - we don't really need this in any case
other than when we have it from the device.
As the new API gives use the spatial reuse 1-4 fields
for trigger-based PPDUs, also expose that to radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When traffic load is not low or low latency is active, TCM schedules
re-evaluation work so in case traffic stops TCM will detect that
traffic load has become low or that low latency is no longer active.
However, if TCM is paused when the re-evaluation work runs, it does
not re-evaluate and the re-evaluation work is no longer scheduled.
As a result, TCM will not indicate that low latency is no longer
active or that traffic load is low when traffic stops.
Fix this by forcing TCM re-evaluation when TCM is resumed in case
low latency is active or traffic load is not low.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is only half-used by mvm (i.e. only the nvm_version part
matters, since the calibration version is irrelevant), so it's
pointless to export it from iwlwifi. If mvm uses this function, it
has the additional complexity of setting the calib version to a bogus
value on all cfg structs.
To avoid this, move the function to dvm and make a simple comparison
of the nvm_version in mvm instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Call the previously introduced apply points entry
point when reaching an apply point.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When ini TLVs are loaded, dump data according to the
stored configuration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In AP mode, if AP supports HE (and the STA), send the
STA_HE_CTXT command.
This is needed mainly for PPE (packet extension) params.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AP mode, if AP supports 11ax, add the MAC_FILTER_IN_11AX
flag in MAC_CTXT command (needed for various 11ax stuff).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW debug data will oneshot read all data available in DRAM
and fill the supplied user buffer. In case the read request
is greater than the new data in DRAM, the driver will write
all data it has and return the buffer immediately.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to check the TWT support of the peer and to
propagte the capability to the firmware.
The current implementation will enable TWT only if the TWT
support is advertised in the HE CAP IE and in the Extended
Capability IE.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW dump was missing in case the RT FW ucode
section failed to load. This failure happens when
the RT section of the FW file is corrupted.
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware stopped looking at this field long ago.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently opmode is limited to asking transport to either
dump all the dumps configured at startup, or monitor only.
Instead, pass to transport a bitmask, to allow flexibility.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can't use SAR Geo if basic SAR is not enabled, since the SAR Geo
tables define offsets in relation to the basic SAR table in use.
To fix this, make iwl_mvm_sar_init() return one in case WRDS is not
available, so we can skip reading WGDS entirely.
Fixes: a6bff3cb19 ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
