This feature turns out to have an issue: it can take up to 8 seconds to
detect high throughput scenarios and to leave RX OMI bandwidth
reduction. This leads to throughput degradation.
Until the issues are fixed, remove the RX OMI implementation.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.a9ccfe210516.Ic87bc7709a6761f593e88f1488a41442c68c1686@changeid
When fips_enabled is set, keys will not be given to the
hardware by mac80211 since the hardware isn't certified.
In this case, various features cannot work correctly as
the firmware needs to handle frames, but it then cannot
since no keys are available.
Disable features:
- WoWLAN since no keys etc.
- MFP since some frames need to be handled in firmware
- EHT/6GHz since MFP is required
Also restrict A-MSDU size since A-MSDUs cannot be split
up by hardware and thus need to fit into the RX buffers
in one piece.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.329fade58a27.I0be27dd329643cc5fdf79a8c8b8f6d2e6fb5c175@changeid
Mostly cleanups. A few fixes and small features.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQM3A3Pv7vbm9vtjWbacY7uyt+OfQUCaFuvoQAKCRDacY7uyt+O
fQTbAP4oQVGex+lUgoGukD7pFShDGo73aFcKsXMbS+68N0GA1QEAqIrbt27keWJS
23ceOELgJlTEzECj2sMy3LzCp7/EFwc=
=xlnn
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-2025-06-25' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Miri Korenblit says:
====================
iwlwifi-next - iwlwifi features
Mostly cleanups. A few fixes and small features.
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a requirement to exit EMLSR if there wasn't enough throughput
in the secondary link.
This is checked in check_tpt_wk, which runs every 5 seconds in a high
throughput scenario (when the throughput blocker isn't set)
It can happen that this worker is running immediately after we entered
EMLSR, and in that case the secondary link didn't have a chance to have
throughput. In that case we will exit EMLSR for no good reason.
Fix this by tracking the time we entered EMLSR, and in the worker make
sure that 5 seconds passed from when we entered EMLSR. If not, don't
check the secondary link throughput.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.c680f8d7dc37.I8a02d1e8d99df3789da8d5714f19b31a865a61ff@changeid
The iwlmld driver is able to handle TTLM changes as long as all TIDs
have the same TID to Link Mapping. Add the corresponding code so that
mac80211 will accept and trigger the TTLM change.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.3b0a4fd2c12b.I1fab7840f1cc222bd1e8cb58ac1a4177474fcd56@changeid
Temporarily block EMLSR when scanning on a P2P Device interface,
as this is an indication that P2P activity is about to start, e.g.,
P2P client connection to a P2P GO.
Since a P2P scan while a station interface connection is active might
be long, increase the EMLSR blocking timeout to 10 seconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.85fb79d537fe.I27523f8d3f00f2b66f5f555f098e323be29465ea@changeid
The (applicable) firmware versions will send an error interrupt as
part of the resume process, so there's no need now to check for it
explicitly. Simplify the code. This also fixes an issue where any
dump taken during the resume isn't able to do the reset handshake
as part of the dump (since interrupts are disabled) and then there
isn't all the correct data and we get more errors later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.9e778f1bae0c.I96483b5236ab23141b45079464c73f93e0164e65@changeid
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of MAC parameters that are in the iwl_cfg
(which is the last config matched to the MAC/RF combination).
This isn't necessary, there are many more of those than MACs,
so move (most of) the data into the MAC family config struct.
Note that DCCM information remains for use by older devices,
and on 9000 series it'll be in struct iwl_cfg but be ignored
when the CRF is in a Qu/So platform.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-15-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
If there is an ongoing scan that lasts long, the MPDU counters may not
increase enough due the device being busy with scanning and not
because we are in a low throughput scenario.
In that case we don't want to block EMLSR.
Instead, stop checking the counters from the moment we started
scanning, and when the scan ends - clear the counters and schedule a
check in 5 seconds, as usual.
Note that this is only done for regular scan since MLO scan is too short
to affect the counters, and scheduled scan is mainly used when we are
not connected.
Also note that we only stop checking whether to block EMLSR, and not if to
unblock.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215512.330ea440d19c.Ib10dae0b7a0cb0e10c59a9edf5ff7af0f065ac60@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Add a new device information 'info' substruct to the transport
that's const and can only be set by a special helper, and move
some information there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224232.cd80cb55403c.Ic18524b66d655fad734bf97192a54d9cfa9fdf1f@changeid
* stack
- free SKBTX_WIFI_STATUS flag
- fixes for VLAN multicast in multi-link
- improve codel parameters (revert some old twiddling)
* ath12k
- Enable AHB support for IPQ5332.
- Add monitor interface support to QCN9274.
- Add MLO support to WCN7850.
- Add 802.11d scan offload support to WCN7850.
* ath11k
- Restore hibernation support
* iwlwifi
- EMLSR on two 5 GHz links
* mwifiex
- cleanups/refactoring
along with many other small features/cleanups
-----BEGIN PGP SIGNATURE-----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=s9mS
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2025-05-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless features, notably
* stack
- free SKBTX_WIFI_STATUS flag
- fixes for VLAN multicast in multi-link
- improve codel parameters (revert some old twiddling)
* ath12k
- Enable AHB support for IPQ5332.
- Add monitor interface support to QCN9274.
- Add MLO support to WCN7850.
- Add 802.11d scan offload support to WCN7850.
* ath11k
- Restore hibernation support
* iwlwifi
- EMLSR on two 5 GHz links
* mwifiex
- cleanups/refactoring
along with many other small features/cleanups
* tag 'wireless-next-2025-05-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (177 commits)
Revert "wifi: iwlwifi: clean up config macro"
wifi: iwlwifi: move phy_filters to fw_runtime
wifi: iwlwifi: pcie: make sure to lock rxq->read
wifi: iwlwifi: add definitions for iwl_mac_power_cmd version 2
wifi: iwlwifi: clean up config macro
wifi: iwlwifi: mld: simplify iwl_mld_rx_fill_status()
wifi: iwlwifi: mld: rx: simplify channel handling
wifi: iwlwifi: clean up band in RX metadata
wifi: iwlwifi: mld: skip unknown FW channel load values
wifi: iwlwifi: define API for external FSEQ images
wifi: iwlwifi: mld: allow EMLSR on separated 5 GHz subbands
wifi: iwlwifi: mld: use cfg80211_chandef_get_width()
wifi: iwlwifi: mld: fix iwl_mld_emlsr_disallowed_with_link() return
wifi: iwlwifi: mld: clarify variable type
wifi: iwlwifi: pcie: add support for the reset handshake in MSI
wifi: mac80211_hwsim: Prevent tsf from setting if beacon is disabled
wifi: mac80211: restructure tx profile retrieval for MLO MBSSID
wifi: nl80211: add link id of transmitted profile for MLO MBSSID
wifi: ieee80211: Add helpers to fetch EMLSR delay and timeout values
wifi: mac80211: update ML STA with EML capabilities
...
====================
Link: https://patch.msgid.link/20250506174656.119970-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a channel context is added, it is still not assigned to the link
and the link is not yet active. As a result, the channel context
min_def is used when the AP is started, even when the full bandwidth
should be used.
Fix it by updating the PHY channel context when the link is already
active so the full bandwidth is used when needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430155443.30b043b10fb1.I62c2aa58687e4796b759fa68132122119a337b49@changeid
This version fixes the issue that was worked around by
iwl_mld_smps_wa. So for FWs with the new version don't do the
workaround, and set new bit added in this version when appropriate.
While at it, rename iwl_mld_smps_wa to iwl_mld_smps_workaround.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250430155443.77fdb18d1ee0.I93688612ac4f6ec99da9bc54bee16554ef40a40b@changeid
If iwl_mld_change_vif_links failed to add the requested link(s)
because the FW is dead (error before recovery), there is no point
in returning an error value, as the reconfig will re-add the link(s)
after the FW is started.
Return 0 in that case, and WARN in the others.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250430151952.c549c72b1f37.I445bf723e9befc9541b4abd0ec7c72db8f1ff177@changeid
From the moment that we have ALIVE, we can receive notification that
are handled asynchronously.
Some notifications (for example iwl_rfi_support_notif) requires an
operational FW. So we need to make sure that they were handled in
iwl_op_mode_mld_start before we stop the FW. Flush the async_handlers_wk
there to achieve that.
Also, if loading the FW in op mode start failed, we need to cancel
these notifications, as they are from a dead FW.
More than that, not doing so can cause us to access freed memory
if async_handlers_wk is executed after ieee80211_free_hw is called.
Fix this by canceling all async notifications if a failure occurred in
init (after ALIVE).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250423091408.a8f63d983466.Ifd77d9c1a29fdd278b0a7bfc2709dd5d5e5efdb1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To cancel all async notifications, we need to:
- cancel async_handlers_wk
- empty async_handlers_list
Instead of having the callers to do both, do it in
iwl_mld_purge_async_handlers_list and rename it accordingly.
Note that the caller iwl_cleanup_mld didn't cancel the work, but it is
harmless.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250423091408.e98aed77e836.Id9f858d9d553d406a24165b09db830df111befce@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 switches between non-MLO and MLO it will recreate the
debugfs directories. This results in the add_if_debugfs handler being
called multiple times. As the convenience symlink is created in the mld
debugfs directory and not the vif, it will not be removed by mac80211
when this happens and still exists.
Add a check and only create the convenience symlink if we have not yet
done so.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250420095642.2490696f032a.I74319c7cf18f7e16a3d331cb96e38504b9fbab66@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The newly added driver causes multiple build problems when CONFIG_PM_SLEEP is
disabled:
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:1982:12: error: 'iwl_mld_resume' defined but not used [-Werror=unused-function]
1982 | static int iwl_mld_resume(struct ieee80211_hw *hw)
| ^~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:1960:1: error: 'iwl_mld_suspend' defined but not used [-Werror=unused-function]
1960 | iwl_mld_suspend(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan)
| ^~~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:1946:13: error: 'iwl_mld_set_wakeup' defined but not used [-Werror=unused-function]
1946 | static void iwl_mld_set_wakeup(struct ieee80211_hw *hw, bool enabled)
| ^~~~~~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c: In function 'iwl_mld_mac80211_start':
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:504:20: error: 'ret' is used uninitialized [-Werror=uninitialized]
504 | if (!in_d3 || ret) {
| ^~
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c:478:13: note: 'ret' was declared here
478 | int ret;
| ^~~
Hide the unused functions and make sure the 'ret' variable is not used
before the initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20250325084340.378724-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mld_remove_link removes the link from both the FW and from the
driver.
If removing it from the FW failed, we assume that the FW is
dead anyway and remove it from the driver as well.
On the other hand, we still return an error value, indicating the caller
(i.e. mac80211) that the link couldn't be removed - while it was
actually removed.
Later, mac80211 might tell the driver again to remove that link,
and then the driver will warn that it doesn't exist.
Fix this by making iwl_mld_remove_link a void function.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.16fe6ebae412.If5371ff7e096b7078ff9e98ff0e72010cd1f076d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow EMLSR if the bandwidths of the links are unequal if one of the
following conditions is true:
1. in low latency mode
2. bandwidth of the secondary link is greater than the bandwidth of the
primary
3. the primary link is active and is loaded enough to justify EMLSR
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.150c330711c4.Ifd72d2e076783991852a7f1756948b4f0efb9fea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel load logic moves from the FW to the driver.
- Implement the logic: allow EMLSR only if the candidate primary link is
active and if its average channel load exceeds the threshold.
- Remove IWL_MLD_EMLSR_BLOCKED_FW. Instead, treat ESR_RECOMMEND_LEAVE in
the EMLSR_RECOMMENDATION notif as an EXIT reason.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.6729a8d67815.Iab39bf0982d8cdbb0db701d31854101c2fcf3b64@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the iwl_mld_get_chandef_from_chanctx() logic, even after
the OMI handshake to reduce bandwidth the driver wouldn't apply
that to the PHY context, since it always uses the normal, not
the reduced, configuration on 6 GHz (not strictly always, but
OMI will only apply if the original bandwidth is > 80 MHz.) Fix
this by making that selection contingent on AP mode. Refactor
the code a bit to also make it clearer why the min_def isn't
used in that case (for FILS.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.2706cbd0b100.Ic34636b1aee81a140eb690fca8139909a58f8e8b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since iwlmld claims wiphys to be self-managed, it needs to
have a regdomain registered before the wiphy is registered
to avoid issues when trying to get the regdomain, e.g. via
"iw phy phy0 reg get".
Move the initialization early, on every FW start not just
when starting to really operate it. This also requires the
self-managed flag to be set early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.10ab8fed94e9.I7c8dee3d14c7427a56882739f82546c6492f3b10@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For each channel context, track the avarage channel load by others in the
driver specific phy data, to be used by EMLSR.
Due to FW limitations, this value is incorrect in EMLSR, so it is
shouldn't be used in EMLSR.
On EMLSR exit, clear it so the wrong value won't be used.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250309073442.dd443fc5b178.I68b2fed197aae14888159b7a73bf40c2f346f41f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user disables power save of a vif that didn't have it enabled
(for example before association), mac80211 will not notify the driver
with BSS_CHANGED_PS. This will cause the driver to not update the
device-level power save to disabled.
Fix this by checking the vif's power save status upon authorization, and
stop considering the vif's power save status on disassociation.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.1cdeb78b19ba.I58fe02c062524029071b04b093a1b09c5e46f4ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi is the driver of all Intel wifi devices since 2008.
Since then, the hardware has changed a lot, but the firmware
API has changed even more. The need to keep one driver that
supports all those different APIs led us to introduce a new
architecture circa 2012 which allowed us to keep the same
interface to the hardware (DMAs, Tx queues, etc...) with a
new layer to implement the mid-layer between mac80211 and
the firmware. The first component is called the 'transport'
and the latter is called 'operation_mode' a.k.a op_mode.
In 2013 we took advantage of the new architecture to
introduce iwlmvm which allowed us to implement the, then,
new firmware API. This op_mode supports 7260 and up, those
devices supports support at least VHT.
Since then, wifi evolved and so did the firmware. It became
much bigger and took a lot of functionality from the driver.
It became increasingly hard to keep the same op_mode for the
newest devices and we experienced frequent regressions on
older devices. In order to avoid those regressions and keep
the code maintainable, we decided it was about time to start
a new op_mode.
iwlmld is a new op_mode that supports BE200 or newer if the
firmware being used is 97.ucode or newer. If the user has
an older devices or BE200 with .96.ucode, iwlmvm will be
loaded. Of course, this op_mode selection is seamless.
All the features supported in iwlmvm are supported in
iwlmld besides a few seldom used use cases: injection and
Hotspot 2.0. Those are under work.
A few points about the implementation:
* iwlmld doesn't have any mutexes, it relies on the
wiphy_lock
* iwlmld is more "resource oriented": stations, links and
interfaces are allocated and freed only after all the
relevant flows are completed.
* Firmware notifications' sizes are validated in a more
structured way.
We would love to see this new op_mode merged in 6.15. The
firmware for this new driver (.97.ucode) is not yet publicly
available but it'll be sent very soon.
People eager to get an early version of this firmware can
contact Emmanuel at:
emmanuel.grumbach@intel.com
I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.
Co-developed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Co-developed-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Co-developed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Co-developed-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Co-developed-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Co-developed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Co-developed-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/linux-wireless/20250216094321.537988-1-miriam.rachel.korenblit@intel.com/
[fix Kconfig, fix api/phy.h includes, SPDX tag and coding
style issues, duplicated includes per 0-day robot]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
