Enhanced DMA design includes the following rings:
- Single RX descriptor ring is used for all VIFs
- Multiple RX status rings are supported, to allow RSS
- TX descriptor ring is allocated per connection
- A single TX status ring is used for all TX descriptor rings
This patch initializes and frees the above descriptor and
status rings.
The RX SKBs are handled by a new entity of RX buffers manager,
which handles RX buffers, each one points to an allocated SKB.
During Rx completion processing, the driver extracts a buffer
ID which is used as an index to the buffers array.
After the SKB is freed the buffer is moved from the 'active'
list to the 'free' list, indicating it can be used for another
descriptor. During Rx refill, SKBs are allocated and attached
to 'free' buffers. Those buffers are attached to new descriptors
and moved to the 'active' list.
New debugfs entries were added to allow edma configuration:
Run the following command to configure the number of status rings:
echo NUM_OF_STATUS_RINGS > num_rx_status_rings
Run the following command to use extended RX status message for
additional debug fields from HW:
echo 0 > compressed_rx_status
Run the following command to control the size of the TX status ring:
echo TX_STATUS_RING_ORDER > tx_status_ring_order
The status ring size will be 1 << tx_status_ring_order
Run the following command to control the size of the RX status ring:
echo RX_STATUS_RING_ORDER > rx_status_ring_order
Due to HW constrains RX sring order should be bigger than RX ring order
The status ring size will be 1 << rx_status_ring_order
Run the following command to change the number of RX buffer IDs:
echo RX_BUFF_ID_COUNT > rx_buff_id_count
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In enhanced DMA the vrings are handled internally by the FW
and are not exposed to the driver.
Instead, the driver handles descriptor rings, which are mapped
by the FW to vrings.
The completions of the TX and RX descriptors are notified to
the driver using status rings. Each status ring descriptor
includes information of the completed descriptors and the ring id
of their descriptor ring.
This patch changes struct vring to generic wil_ring to allow
its reuse for enhanced DMA descriptor rings and adds the descriptor
and status rings specific descriptors.
The vring debugfs entries have changed as follows:
- dbg_vring_index has changed to dbg_ring_index
- vrings has changed to rings
- vring_idle_trsh has changed to ring_idle_trsh
- vring_index has changed to ring_index
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add changes to support initialization of Talyn-MB wil6210
device:
- Add definition for Talyn-MB new JTAG id
- Define talyn_mb_fw_mapping array
- Add Talyn-MB reset sequence
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unused members from struct wil_tid_ampdu_rx
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rearrange the code by having new function wmi_mgmt_tx() to take care
of the WMI part of wil_cfg80211_mgmt_tx().
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change the type of the argument reply_size from u8 to
u16 in order to support reply sizes > 255 bytes.
The driver already supports u16 reply size in all
other places, this was the only missing change.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Track the connection status per-VIF.
The data path code is also updated to support multiple VIFs.
This includes RX and TX VRING management, NAPI poll loops,
RX reordering and related code.
Power management code used to check if the main interface
is up or based on connection state of the main interface,
adapt this code to take all VIFs into account.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As more support is added for multiple VIFs, there is a need
to protect the wil6210_vif structure from access while it is
deleted (mainly from del_virtual_intf operation).
Instead of adding another mutex, use p2p_wdev_mutex and rename
it to vif_mutex to reflect the added role. Its existing roles
are similar so it extends nicely (for example it protects the
scan_request member which is also a member of wil6210_vif).
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for multiple VIFs in the cfg80211 operations start_ap,
stop_ap and change_beacon. This change allows starting multiple APs
using virtual interfaces.
The data path and most other operations are still working only
on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add generic support in cfg80211 operations add_virtual_intf
and del_virtual_intf for adding/removing VIFs of any
interface type, and fix change_virtual_intf to allow changing
the interface type of a VIF. Previously these operations
only worked for the P2P_DEVICE interface which is not a real
VIF(it is management-only and shares radio with the main
interface).
Currently the interface combination is validated, the VIF is
added/removed in the firmware and the appropriate net/wireless
device is also added/removed.
Added minimal support for proper interface up/down and module
unload but most operations still work only on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simple infrastructure changes for supporting multiple
virtual interfaces (multiple VIFs).
It is still not possible to add new VIFs so the only VIF
belongs to the main interface.
Main changes:
1. Add MAC ID(mid) argument to wmi_send and wmi_call to
allow invoking WMI commands on different VIFs.
2. Similarly, in WMI event handler look at the mid reported
by FW and extract VIF structure (currently only for main
interface). All WMI event handlers operate on wil6210_vif
structure so they know on which VIF they were called.
3. Trivial changes to use wil6210_vif structure and MID
throughout the code.
4. Various changes to logging to report MID.
More complete multiple VIFs support will be added gradually
in next patches.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New FW which supports multiple virtual interfaces, reports
its allowed interface combinations using a special comment
record in the FW file. The format of the interface combinations
is similar to the kernel wiphy->iface_combinations.
When parsing FW file during module initialization, also parse
and validate the concurrency record, and initialize
wiphy->n_iface_combinations and wiphy->iface_combinations
accordingly.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For supporting multiple virtual interfaces in the future,
introduce a wil6210_vif structure which will hold per-VIF
data. Change the module initialization so wil6210_vif will
be part of net_device structure, and wireless_dev will be
embedded inside the wil6210_vif structure. This will allow
us to find the appropriate wil6210_vif structure when we
only have access to wireless_dev or net_device.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to allow using the same brd file across different
11ad chips, the address for loading the brd file should be
part of the FW file, instead of the brd file. The brd file is
expected to include only one section.
To allow backward compatibility the driver reads the
address from the brd file in case it is not included in the
FW file.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sparrow D0 chips have slightly larger mac_rgf_ext section
in order to support extra features such as multiple virtual
interfaces.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when we want to bring the interface up, we first
reset the device which causes the boot loader to run. Then
we halt the device CPU, load FW image and resume the device
CPU.
There are some boot loader versions which perform redundant
memory accesses even when idle. Halting the device CPU
while boot loader access memory can cause the device memory
controller to get stuck, the FW will fail to load and the
network interface will not come up.
For such boot loaders implement a workaround where we freeze
the boot loader before halting the device CPU, so it will not
perform any memory accesses.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
OTP HW vectors values are different for 40MHz and 330MHz AHB
clocks.
In SW reset flow, the host driver sets the clock frequency
to 40MHz. In order to allow reading from the OTP, the host
driver should configure the OTP HW vectors with the values
that fits this clock frequency.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add Talyn JTAG ID to the list of valid IDs
and identify this device as Talyn.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field preset_chandef of wireless_dev must not be accessed
by the driver because it is private to cfg80211. Store the
monitor channel locally in wil6210_priv instead.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"FIXME: IRQ mask debug" and "FIXME: interrupts enabled - for debug"
can be removed because wil6210_debug_irq_mask() is now considered
production feature.
"FIXME FW can transmit only ucast frames to peer" and "FIXME real
ring_id instead of hard coded 0" can be removed because FW/HW already
support multicast transmission.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Suspend and crash dump operations can happen simultaneously
in case there is a FW assert during the suspend procedure
or when SSR calls all the devices crashdump callbacks.
To prevent that, a new flag is added, indicating that the
dumps collection is in progress, in order to allow the
suspend/reset decline if the dumps collection already started.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add get_capa callback to platform ops to allow reading the platform
capabilities.
Supported capabilities:
- Keeping 11ad connection during suspend
- T_POWER_ON 0 support
- Usage of external clock
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the option to support 40bit addresses since some platforms
may not support 48bits but support 40bits
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for sched_scan_start/stop by sending PNO commands to FW.
Driver reports max_sched_scan_reqs and invokes
cfg80211_sched_scan_results upon receiving WMI_SCHED_SCAN_RESULT_EVENTID
from FW.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The #ifdef checks are hard to get right, in this case some functions
should have been left inside a CONFIG_PM_SLEEP check as seen by this
message:
drivers/net/wireless/ath/wil6210/pcie_bus.c:489:12: error: 'wil6210_pm_resume' defined but not used [-Werror=unused-function]
drivers/net/wireless/ath/wil6210/pcie_bus.c:484:12: error: 'wil6210_pm_suspend' defined but not used [-Werror=unused-function]
Using an __maybe_unused is easier here, so I'm replacing all the
other #ifdef in this file as well for consistency.
Fixes: 94162666cd ("wil6210: run-time PM when interface down")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the statistics show how many successful/failed
suspend/resume operations the system had.
Update the statistics by splitting each successful/failed
suspend/resume operations to radio on/off.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently suspend time statistics are showed through debugfs.
Remove time statistics in suspend state since the timing may
not be accurate in that state.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of interface down, radio is turned off but PCIe mastering is
not cleared.
This can cause unexpected PCIe access to the shutdown device.
Fix this by clearing PCIe mastering also in case interface is down
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When loading FW from file add block size checks to ensure a
corrupted FW file will not cause the driver to write outside
the device memory.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW capabilities are currently retrieved only during module
initialization, but userspace can replace the firmware while
interface is down, so refresh the FW capabilities when
interface is up (after FW is loaded) to ensure driver
functionality matches the loaded FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow run-time suspend when interface is down, keep card alive when
interface is up.
If driver is in wmi only or debug_fw mode run-time PM won't suspend.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW starts running it can get D0 to D3 interrupt that is a leftover
from previous system suspend while FW was not running.
As this interrupt is not relevant anymore, clear it part of device reset
procedure.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since debugfs is a kernel configuration option, enable the driver to
compile without debugfs.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
vring_idle_trsh is used in the operational driver, hence
should not be defined as a debugfs variable.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store initial FW RF calibration result in driver. Set this calibration
result back to FW after each FW reset in order to avoid future calibration
procedures.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add statistics for total, min and max suspend time, that
calculates the time the 11ad device was in suspend.
Those statistics will help to estimate the power impact
of d3hot feature.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Wireless drivers should not be using ioctl interface,
hence remove this interface for wil6210 driver.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to preserve the connection in suspend/resume flow,
wil6210 host allows going to PCIe D3hot state in suspend,
instead of performing a full wil6210 device reset. This
requires the platform ability to initiate wakeup in case of
RX data. To check that, a new platform API is added.
In addition, add cfg80211 suspend/resume callbacks
implementation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wil6210 devices can have different PCIe bar size, hence get the
bar size from PCIe device instead of using a constant bar size.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Module parameter allows to load specific FW used
for FTM testing.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case wil6210 resume fails, wil6210 suspend function will try
to access the suspended device in the next kernel suspend.
To prevent that, add wil_status_suspended flag to indicate if the
device is already suspended and clear it only if the resume succeeds.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
debugfs ioblob function is called by the FW logs scripts
to copy the FW logs via PCIe.
As the FW logs collection is done in parallel to the operational
11AD actions, the HALP voting can take place during 11AD reset flow
and other sensitive scenarios.
To prevent that, remove HALP voting from the ioblob function.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 11ad spec requires 11ad devices to be able to receive 8KB
packets over the air. Currently this is only possible by
loading the driver with mtu_max=7912 but this also forces
a smaller block ACK window size which reduces performance
for stations which transmit normal sized packets (<2KB).
Fix this problem as follows:
1. Add a module parameter rx_large_buf that when set,
will allocate 8KB RX buffers regardless of mtu_max
setting.
2. When receiving block ACK request agree to any window
size not above our maximum, regardless of the mtu_max setting.
This means if the other side transmits small packets (2KB)
it can still set up block ACK with a large window size,
and get better performance.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power save profile is set to default state in case of FW reset,
regardless of the state before the reset took place.
Fix this by saving the current power save profile and restore it
in case of FW reset.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a new value to the oob_mode module parameter for
supporting AP certification.
All enabled values of oob_mode (>0) are intended only
for debugging and diagnostics.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver always invoke cfg80211_disconnected() with locally_generated as
false.
Fix this by reporting true whenever the disconnect is triggered from
upper layers (cfg80211) or from within the driver itself (reset,
deinit).
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In a fast disconnect/connect sequence, cfg80211_connect_result() can
fail to find the bss object which the driver is connecting to. Detailed
sequence of events:
* Driver is connected in STA mode
* Disconnect request arrives from user space. Driver disconnects and
calls cfg80211_disconnected() which adds new event to the
cfg80211_wq worker thread
* Connect request arrives from user space. cfg80211_connect() stores
ssid/ssid_len and calls rdev_connect()
* __cfg80211_disconnected() runs in worker thread and zero
wdev->ssid_len
* Connect succeeds. Driver calls cfg80211_connect_result() which fails
to find the bss because wdev->ssid_len is zero
To overcome this, upon connect request, store the bss object in the
driver and upon connect completion pass it to kernel using
cfg80211_connect_bss().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some dynamic debug printouts in driver are using print_hex_dump_bytes.
However, with dynamic debug disabled, print_hex_dump_bytes outputs to
log unconditionally.
Use print_hex_dump_debug instead to prevent log pollution when dynamic
debug disabled.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver uses the bus_request platform operation to
request resources from the platform for a specific bandwidth.
Currently the driver requests resources for the maximum
theoretical bandwidth, when interface is brought up.
Refine this process a bit: now the driver will request a
small amount of resources when interface is up, and will only
issue the maximum request when connected.
This mechanism will be improved further in the future to make
more refined requests based on actual bandwidth.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
device supports 48bit addresses, reflect that by
setting the dma mask accordingly.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add an option to specify and override the A-BFT length when
starting an AP/PCP. See IEEE P802.11-2016, 10.38.5.
The abft_len must be set before starting AP/PCP. It is only
needed for diagnostics and certification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add reporting of the association ID (AID) for each station
as part of the stations file in the debugfs.
Valid AID values are 1-254. 0 is reported if the AID
is unknown or not reported by firmware.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver may be used in platforms where some use sparrow cards while
other use sparrow-plus cards, where different FW image is needed.
Add the capability to load dedicated FW image in case sparrow-plus
card is detected and fallback to default image if such does not exist.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default, AP SME is handled by driver/FW.
In case disable_ap_sme is true, driver doesn't turn-on
WIPHY_FLAG_HAVE_AP_SME and the responsibility for
AP SME is passed to user space.
With AP SME disabled, driver reports assoc request frame
to user space which is then responsible for sending assoc
response frame and for sending NL80211_CMD_NEW_STATION.
Driver also reports disassoc frame to user space
which should then send NL80211_CMD_DEL_STATION.
NL80211_CMD_SET_STATION with NL80211_STA_FLAG_AUTHORIZED
is used by user space to allow/disallow data transmit.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added new areas to fw_mappings area for UCODE code
and data areas.
The new areas are only exposed through debugfs blobs,
and mainly needed to access UCODE logs.
The change does not affect crash dumps because the
newly added areas overlap with the "upper" area which
is already dumped.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently it was possible to call remain_on_channel(ROC)
while scan was active and this caused a crash in the FW.
In order to fix this problem and make the behavior
consistent with other drivers, queue the ROC in case
a scan is active and try it again when scan is done.
As part of the fix, clean up some locking issues and
return error if scan is called while ROC is active.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for setting retry limit for short frames,
using NL80211_CMD_SET_WIPHY with the attribute
NL80211_ATTR_WIPHY_RETRY_SHORT.
Update wiphy->retry_short from the FW default when interface
is brought up.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement cfg80211 abort_scan op to allow the upper layer to
abort an ongoing scan request.
In addition, notify wil6210 device on scan abort request instead
of just ignoring the scan response.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New power management wmi commands provide the ability to change
the device power save profile (enable / disable power save).
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver calls to netif_tx_stop_all_queues/netif_tx_wake_all_queues are
inconsistent. In several cases, driver can get to a situation where net
queues are stopped forever and data cannot be sent.
The fix is to stop net queues if there is at least one vring which is
"full" and to wake net queues if all vrings are not "full".
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the FW version is taken from the sw_version field
of the FW ready event. This version is based on internal
version control revision and it is difficult to map to actual
FW version.
Fix this by using the actual FW version stored in the FW file
header record.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When driver is loaded, extract a capabilities record
from the FW file. This record contains bits indicating
which optional features are supported by this FW.
The driver can use this information to determine
which functionality to support and/or expose to user
space.
The extraction is done before wiphy structure is
registered, because the capabilities can affect
information published by the this structure.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the places that check wil->scan_request and
call cfg80211_scan_done are not consistently protected,
so there is a risk that cfg80211_scan_done will be called
with NULL scan_request, causing a kernel crash.
Fix this by using p2p_wdev_mutex in few other places
that access scan_request. This makes sense since
scan_request may point to p2p_wdev, and it is not worth
the extra complexity of adding a new mutex.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
fix stop p2p device handling to identify between search
and listen and update the upper layers with the appropriate
notification.
The stop of p2p radio operations also needs to be performed
in __wil_down.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case HALP vote times out, we need to mask the HALP IRQ, as done
in case the interrupt is received, as this interrupt should be
set until completion of the low latency operation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The nl80211 layer expects P2P search operation to be aborted
if needed when stopping P2P device. If the P2P search operation
is still running after returning from stop_p2p_device
it causes a WARN_ON and possibly a kernel crash.
Fix this by aborting the P2P search in wil_cfg80211_stop_p2p_device
and preventing P2P search from being started on a stopped P2P
device.
Note, the fix does not cover the case where a regular scan
is started on the P2P device. It will be completed in the
future when support is added for aborting a scan operation.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adding pm_notify to allow the following:
1. Check if suspend is allowed in an earlier stage to prevent
starting the suspend procedure in case it is not allowed
2. Notify the platform driver on the suspend request
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the ability to configure the device led to be used for notifying
the AP activity (60G device supports leds 0-2).
The host can also configure the blinking frequency of the led in
three states.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In idle times 60G device can enter deep sleep and turn off
its XTAL clock.
Host access triggers the device power-up flow which will hold
the AHB during XTAL stabilization until device switches from
slow-clock to XTAL clock.
This behavior can stall the PCIe bus for some arbitrary period
of time.
In order to prevent this stall, host can vote for High Latency
Access Policy (HALP) before reading from PCIe bus.
This vote will wakeup the device from deep sleep and prevent
deep sleep until unvote is done.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Network stack can try to transmit data while AP / STA is
disconnected.
Change this print-out to debug level as this should not be
handled as error.
This patch also adds wil_dbg_ratelimited, used to limit the
above print-out.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
P2P search can only run on the social channel (channel 2).
When issuing a scan request on the P2P_DEVICE interface,
driver ignored the channels argument and always performed a P2P
search.
Fix this by checking the channels argument, if it is
not specified (meaning full scan) or if a non-social channel
was specified, perform a regular scan and not a P2P search.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add __func__ to wil_err and wil_info for easier
debugging.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add module parameter oob_mode. Takes effect the next time
the interface is brought up and FW is loaded. Puts the FW
in special "out of the box" (OOB) mode which is used for
diagnostics and certification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When starting a PCP, pass the is_go flag to firmware in
wmi_pcp_start. This flag indicates whether we started
a PCP which is also a GO(P2P group owner) or just a regular
PCP.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW crashed with no_fw_recovery mode enabled, user space
could still call wil_cfg80211_change_iface quickly to change
interface type, and this would cause recovery to proceed and
FW crash logs may be lost.
Fix this problem by not resetting the FW in case no_fw_recovery
is enabled.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix 2 race conditions found during test runs of P2P discovery:
1. Because wil_p2p_cancel_listen was not protected, user space
could start a new P2P listen/search before wmi_stop_discovery
completed. This caused a crash in the firmware.
2. In P2P listen, when listen timer expires and user space calls
cancel_remain_on_channel at the same time, code could send the
cfg80211_remain_on_channel_expired notification twice.
Added protections with wil->mutex to several places that call
wmi_stop_discovery.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added support for the P2P_DEVICE virtual interface. This interface
is intended for P2P management operations such as discovery and
GO negotiation. Normally it is implemented by drivers to allow
a separate interface for P2P management with its own MAC address,
but for 11ad drivers it is needed to support P2P search, since it
cannot otherwise be separated from normal scan.
Since we only support a single interface/MAC address, we can't
easily separate between primary and P2P_DEVICE interfaces.
For example when a management packet arrives we can't tell for
which interface it is intended. To work around this, we store
a pointer to the interface where the last "radio operation" was
triggered such as scan or remain on channel, and we forward
management packets and scan results to this interface.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
supporting p2p_find, p2p_listen and p2p_connect
Use updated cfg80211_get_bss API (additional argument)
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
For example, stations inside a PBSS can communicate directly, and
the PCP role can be transferred between stations.
This change adds PBSS support, and has 2 main parts:
1. When starting an AP, add an option to start as a PCP instead.
This is implemented by a new PBSS flag which is passed as part of
the cfg80211_ap_settings structure.
2. When connecting to a BSS, add an option to connect to a PCP
instead of an AP. This is again implemented by a new PBSS flag,
added to the cfg80211_connect_params structure.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Switch to auto-generated version of wmi.h which is maintained
by FW team. This will allow better sync between teams in the
future and avoid bugs because of unexpected API changes.
The wmi.h will have many differences but most are cosmetic.
It also includes these real differences:
1. is_go parameter added to BCON_CTRL and START_PCP commands.
2. max_rx_pl_per_desc added to CFG_RX_CHAIN command.
3. various small API updates that are not currently used by
driver.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for discovery mode during scan. When discovery mode
is active, station transmits special beacons while scanning.
This can optimize the scan mainly when there is only one AP/PCP
around.
Discovery mode is implicitly used by firmware during P2P search.
Since there is currently no use case where user space has a
reason to directly control discovery mode, we expose it only
through a debugfs flag.
Also fix name confusion in the wmi_scan_type enumeration.
The type previously called WMI_LONG_SCAN is actually
WMI_ACTIVE_SCAN.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI synchronous handling has changed and WMI calls that provide
a buffer for the reply are completed in the WMI interrupt context.
This allows sending the RX and TX BACK commands from the WMI event
handler without the need for the worker thread.
This is a better approach as it can decrease the handshake time
in the connect flow and prevent race conditions in case of fast
disconnects. An example for such a race is handling of wil_back_rx_handle
during a disconnect event, as wil_back_rx_handle is not protected by
the wil mutex and a disconnect can be handled after sta->status is
verified as connected.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx vring needs to be enlarged to get better
performance for traffic over 2Gbps.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211_ops.disconnect() should wait for disconnect flow to
complete. If it does not, internal state becomes out of sync with
one in cfg80211. If one does stress test connect/disconnect
sequence, cfg80211 will issue next connect before disconnect
completed internally.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the current solution wil6210 configures the vring in a worker
and holds only one pending CID. This implementation may lead to
race conditions between connect and disconnect events of multiple
stations or fast connect/disconnect events of the same station.
In order to allow the removal of the connect worker and handling of
WMI_VRING_CFG_DONE_EVENTID in the connect event, the WMI replies
that provide the reply in a given buffer needs to be handled
immediately in the WMI event interrupt thread.
To prevent deadlocks, WMI replies that requires additional
handling are still handled via the events list.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added a simple interface for platform to perform crash
recovery.
When firmware crashes, wil driver can notify the platform
which can trigger a crash recovery process. During
the process the platform can request a ram dump
from the wil driver as well as control when firmware
recovery will start. This interface allows the platform
to implement a more advanced crash recovery, for
example to reset dependent subsystems in proper order, or
to provide its own notifications during the recovery process.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:
- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During reset flow, ignore firmware errors detected prior
to the actual hardware reset as the recovery flow would
make additional unnecessary reset.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When firmware crashes, just before firmware recovery,
dump the firmware memory to a devcoredump device.
The resulting dump can be read from user space to be used
in offline crash analysis.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Print firmware and ucode assert codes when firmware crashed.
Signed-off-by: Lior David <liord@qti.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On Rx, when invalid frame is received and dropped,
reaping of next frames from Rx ring is stopped.
This stops NAPI polling and re-enables the Rx interrupt.
However, in cases where no more frames received,
interrupt will not be triggered and rest of Rx frames
will not be processed.
Skip bad frames and continue to reap Rx packets when
such frames are encountered, and add statistics for
such frames for debug.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Support for the system suspend/resume.
In preparation for the run-time PM, implementation made
run-time PM friendly: common for system and run-time PM
code factored out as generic functions, albeit is_runtime
parameter value is always false currently.
For debug purposes, "PM" debug category introduced.
Policy: AP-like interface can't be suspended; otherwise
suspend is allowed. Hardware brought down if interface
was up. Connection, if existed, get lost.
Interface will be brought up upon resume if it was up
before suspend.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace macros like "R", "W", "S", "C", defined multiple times,
with inline functions "wil_[rwsc]".
Use "readl" and "writel" instead of "ioread32" and "iowrite32"
since it is granted that memory transactions are used,
not port ones like IN/OUT
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the recent kernel versions, multiple MSI is not well supported.
In particular, it is not supported on x86 and ARM architectures.
Also, internal interrupt handling logic is simpler and
more effective when using single interrupt.
Remove support for 3 MSI, convert module parameter
"use_msi" from int with range [0,1,3] to boolean.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx drops may be for 2 reasons: frame is old,
or it is duplicate. On the debugfs "stations" entry,
provide counters per reorder buffer for total
frames processed, drops for these 2 reasons.
Also add debug print for dropped frames.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When performing Rx reordering, count skb's dropped
per reorder buffer; and print dropped packets count
on the "stations" debugfs entry
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
