memcpy operation is next to memset code, and the size to copy is equals to the size to
memset, so the memset operation is unnecessary, remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201223012516.24286-1-zhengyongjun3@huawei.com
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/f932c887e013767cbdabfdddd671086e8ae63193.1605896060.git.gustavoars@kernel.org
This commit updates the BMPS exit path to be consistent with downstream in
terms of exiting BMPS mode. Downstream sets the flag to send a NULL data
frame to the host on exiting BMPS.
This will tell the AP to send any queued frames to the STA immediately.
Verified the relevant bit toggle in wireshark.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201120021403.2646574-2-bryan.odonoghue@linaro.org
This patch calls wcn36xx_smd_keep_alive_req() on the STA patch immediately
after associating with an AP.
This will cause the firmware to send a NULL packet out to the AP every 30
seconds, thus offloading keep-alive processing from the SoC to the
firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-4-bryan.odonoghue@linaro.org
This patch switches on CONNECTION_MONITOR. Once done it is up to the
firmware to send keep alive and to monitor the link state.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-3-bryan.odonoghue@linaro.org
The firmware parameter LINK_FAIL_TX_CNT maps to the prima configuration
file parameter gLinkFailTxCnt and is described as:
quote: " If within gLinkFailTimeout period(values is mentioned in msec) if
FW doesn't receive acks for gLinkFailTxCnt number of packets, then
link will be disconnected."
The downstream description sets a minimum value of 1000 a maximum value of
60000 and a default value of 6000, however it appears that unless we
actually set this value deliberately firmware defaults it to 0.
Setting this value to non-zero results in the firmware doing link
monitoring. The working example from downstream paradoxically sets the
value to 200, here we opt to set the value to the minimum stipulated in the
configuration file 1000.
In conjunction with ieee80211_hw_set(wcn->hw, CONNECTION_MONITOR); this
change effects offload of link monitoring to the firmware.
Tested with:
'CNSS-PR-2-0-1-2-c1-74-130449-3' wcn3620
'CNSS-PR-2-0-1-2-c1-00083' wcn3680
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-2-bryan.odonoghue@linaro.org
In bmps mode, beacons are filtered, and firmware is in charge
of monitoring the beacons and report changes or loss.
mac80211 must be advertised about such change to prevent it's
internal timer based beacon monitor to report beacon loss.
Fix that by setting/clearing the IEEE80211_VIF_BEACON_FILTER
vif flag on bmps entry/exit.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592471863-31402-2-git-send-email-loic.poulain@linaro.org
This is a small update to fix an error I saw where a few functions do not
have a blank line in between them.
Affects smd.c and main.c - no logic is affected by this change.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-3-bryan.odonoghue@linaro.org
This commit marks all smd.c functions that are only used inside of smd.c as
static. Previous commits added some VHT specific setup functions non-static
which is the right thing to do in terms of having granular git commits that
compile warning free. What we really want is for local not global scope on
those functions.
This patch makes the conversion from global to local scope.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-2-bryan.odonoghue@linaro.org
This patch adds ieee802.11 VHT flags for the wcn3680b.
- RX_STBC1
- SU Beamformee
- MU Beamformee
- VHT80 SGI
- Single spatial stream
RX LDPC is declared as supported in the datasheet but not enabled at this
time.
After this patch is applied an AP should see the wcn3680 as an 802.11ac
capable device.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-5-bryan.odonoghue@linaro.org
This commit adds VHT rates to the wcn36xx_update_allowed_rates() routine.
Thus allowing the driver to latch the declared rates and transmit them to
the firmware in the same way as other 80211.n rates are.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-4-bryan.odonoghue@linaro.org
In order to send VHT parameters to wcn3680 we need to pass the extended V1
parameter structures to the firmware. These commands need to have the
version number set to 1.
This patch makes the conversion. The conversion consists of
1. Setting the version number for wcn3680 or leaving it at 0 otherwise
2. Setting the size of the packet header lower for wcn3620 and wcn3660
Once done all three chips can continue to use the same code to pass
parameters to their respective firmware. In the case of the wcn3680 the
passed structures will be slightly larger to accommodate communication of
VHT descriptors.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-3-bryan.odonoghue@linaro.org
In order to pass 802.11ac VHT parameters from the SoC to wcn36xx we need to
use the V1 data structures associated with BSS and STA parameters.
The means of identifying a V1 data-structure is via the SMD version field.
This patch defines a INIT_HAL_MSG_V1() which operates the same way as
INIT_HAL_MSG() with the exception that it defines VERSION1 as opposed to
VERSION0.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-2-bryan.odonoghue@linaro.org
This commit makes use of wcn36xx_smd_set_bss_vht_params() to extract VHT
parameters from the 80211_sta structure and latch appropriate bits in the
bss_params_v1 structure for transmission to the wcnss firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-5-bryan.odonoghue@linaro.org
This commit modifies wcn36xx_smd_start() so that it can download wcn3680
specific firmware parameters if we are talking to the wcn3680. If not the
original generic firmware parameter table should continue to be used for
wcn3620 and wcn3660.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-4-bryan.odonoghue@linaro.org
This commit defines a firmware configuration for the wcn3680 which
represents a working downstream configuration. This configuration has been
successfully applied to the upstream driver with antecedent patches
resulting in the same or better through-put in comparison to the
downstream driver on the test hardware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-3-bryan.odonoghue@linaro.org
In order to get 802.11ac working the way we want, additional parameters
need to be passed down to the firmware.
This patch takes the full remaining set of parameters defined in the
downstream riva/inc/wlan_hal_cfg.h and imports them into hal.h with some
minor name length adjustments.
This addition will allow us to pass a larger firmware configuration set
later on.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-2-bryan.odonoghue@linaro.org
For the 80MHz channel we need to set the PHY mode to one of four PHY modes
that span the 80MHz range.
This patch latches the hw_value PHY field previously defined for 5GHz
channels directly to the parameter passed to the firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-6-bryan.odonoghue@linaro.org
This commit encodes the 802.11ac PHY mode for a given channel in the upper
bits of the hw_value field. This allows for a neat read-out and application
of the relevant PHY setting.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-5-bryan.odonoghue@linaro.org
Adds HW_VALUE_PHY(hw_value) an access macro that will be used to
extract a hardware specific PHY setting for a given channel.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-4-bryan.odonoghue@linaro.org
Uses HW_VALUE_CHANNEL() to extract the channel number from a
struct ieee80211_channel->hw_value. Once done we can use the upper bits of
the hw_value to encode PHY related data.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-3-bryan.odonoghue@linaro.org
Adds HW_VALUE_CHANNEL(hw_value) an access macro that will be used to
extract the channel number from struct ieee80211_channel->hw_value in
preparation for also storing PHY settings for 802.11ac in the upper bits of
hw_value.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-2-bryan.odonoghue@linaro.org
wcn36xx_smd_config_bss_v0() and wcn36xx_smd_config_bss_v1() have been
designed to operate in standalone fashion. As a result we can drop the
dead code now present in wcn36xx_smd_config_bss() and happily remove one
kzalloc from the BSS config path as we do so.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-8-bryan.odonoghue@linaro.org
A previous patch added wcn36xx_smd_config_bss_v0() this patch converts the
version 0 data-path in wcn36xx_smd_config_bss() to use
wcn36xx_smd_config_bss_v0().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-7-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_config_bss_v0() as a step along the road of
functionally decomposing wcn36xx_smd_config_bss().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-6-bryan.odonoghue@linaro.org
This patch updates wcn36xx_smd_config_bss_v1() to update on internally
derived parameters only, specifically making use of STA v1 wrapper routines
previously added.
Once done we no longer need to pass a struct wcn36xx_hal_config_bss_req_msg
which gives us options in later patches to eliminate the kzalloc() in
wcn36xx_smd_config_bss entirely.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-5-bryan.odonoghue@linaro.org
This commit moves BSS parameter setup to a separate function
wcn36xx_smd_set_bss_params(). This will allow for further functional
decomposition and fewer kzalloc() operations in subsequent patches.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-4-bryan.odonoghue@linaro.org
In order to facilitate functional decomposition of
wcn36xx_smd_config_bss() we need to move wcn36xx_smd_set_sta_params() later
in function.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-3-bryan.odonoghue@linaro.org
This commit functionally decomposes wcn36xx_smd_config_sta into a clearly
defined wcn36xx_smd_config_sta_v0 and wcn36xx_smd_config_sta_v1 path.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-2-bryan.odonoghue@linaro.org
This commit adds a wrapper function wcn36xx_smd_set_sta_params_v1() which
calls into wcn36xx_smd_set_sta_params() and then subsequently sets
version-1 specific parameters.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-8-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_set_bss_vht_params(). The job of this function
is to decide if the BSS is VHT capable and if so set the appropriate bit
in the BSS parameter structure for passing to the firmware.
VHT Channel width set is not set since we don't support 160MHz.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-7-bryan.odonoghue@linaro.org
Adds a routine to allow setting the LDPC bit for HT parameter passing
inside the version 1 STA parameters data structure.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-6-bryan.odonoghue@linaro.org
This commit adds support for setting VHT parameters based on the declared
VHT capability bits in the VHT capability structure.
We cannot do 160MHz so VHT Channel width set should be zero.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-5-bryan.odonoghue@linaro.org
Toggling the LDPC enabled bit is possible only via the extended V1
data-structure. This function provides a means of setting the default
depending on chip-type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-4-bryan.odonoghue@linaro.org
This commit adds support for setting default VHT parameters, which are
exposed by the extended version 1 STA parameter type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-3-bryan.odonoghue@linaro.org
This patch converts the internal data structure used to store data-rates
from version 0 to version 1.
This allows us to extend out the internal storage to represent VHT
parameters.
Using the extended version 1 data-structure allows us to avoid a whole raft
of version 1 specific fixup functions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-3-bryan.odonoghue@linaro.org
In order to pass VHT parameters to wcn3680 we need to use a super-set of
the V1 data-structures with additional VHT parameters tacked on.
This patch adds the additional fields to the STA and BSS parameter
structures.
Since neither wcn3620 nor wcn3660 support VHT the size of the passed
message is fixed to the previous message length. Subsequent changes will
differentiate between wcn3620/wcn3660 and wcn3680 which does use the larger
message size.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-2-bryan.odonoghue@linaro.org
In order for the firmware to process extended V1 parameters with the
addtional VHT fields added we need to first enable the feature bit DOT11AC.
Once done the version number in the HAL message header will be acted upon
by the firmware.
Extended V1 parameters are a prerequisite for 802.11ac speeds since we
cannot communicate VHT parameters to the firmware absent the extended data
structures.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-11-bryan.odonoghue@linaro.org
Two pointers are already defined in this function "bss" and "sta" which
point to fields within msg_body->bss_params.
We can substantially reduce the amount of extraneous text in this function
by making use of those pointers. This change makes the code easier to read
and modify.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-10-bryan.odonoghue@linaro.org
Specify the number of spatial streams in ieee80211_rx_status. For non VHT
data-rates the wireless core doesn't care about this field, however for VHT
data-rates it does.
Every version of wcn36xx has one spatial stream, so specify nss for
wcn3620, wcn3660 and wcn3680 now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-7-bryan.odonoghue@linaro.org
The rate_idx is the index of the bitrate in the supported rate table.
However the 5Ghz band has a smaller legacy bitrate table than 2.4Ghz
since it does not have the DSSS bitrates (1, 2, 5.5, 11).
So in 5Ghz band the index should adjusted accrodingly (-4).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[bod: Made sure fix is only applied if the rate_idx > n_bitrates]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-6-bryan.odonoghue@linaro.org
If DT indicates we are dealing with a WCN3680 mark the rf_id field as
RF_IRIS_WCN3680 allowing for further chip-specific logic.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-3-bryan.odonoghue@linaro.org
The WCN3680 has some specific behaviours that we want to capture to
distinguish it from the WCN3620 and WCN3660 respectively.
Add an identifier for this purpose.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-2-bryan.odonoghue@linaro.org
For whatever reason, when connected to an open/no-security BSS,
the wcn36xx controller in bmps mode does not forward 'wake-up'
beacons despite AP sends DTIM with station AID.
Meaning that AP is not able to wakeup the station and needs to wait
for the station to wakeup by its own (TX data, keep alive pkt...),
causing serious latency issues and unexpected deauth.
When connected to AP with encryption enabled, this issue does not occur.
So a simple workaround is to only enable bmps support in that case.
Ideally, it should be propertly fixed to allow bmps support with open
BSS, whatever the issue is at driver or firmware level.
Tested on wcn3620 and wcn3680.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598363127-26066-1-git-send-email-loic.poulain@linaro.org
By default, after associated to an AP, the wcn36xx bitrate adjustment
algorithm starts sending data at 1Mbps, and increases the rate slowly
(1Mbps, 2Mbps, 6Mbps...) over the further TX packets.
Starting at 1Mbps usually causes the initial throughput to be really
low and the maximum possible bitrate to be reached after about hundreed
of TX packets.
That can be improved by setting a different initial bitrate for data
packets via the ENABLE_DYNAMIC_RA_START_RATE configuration value, this
value can be a legacy or MCS rate.
This patch sets the starting bitrate value to MCS-5, which seems to be
a good compromise given it can be quickly adjusted low or up if necessary.
(and based on what I observed in the wild with some mobile devices)
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598345341-4505-1-git-send-email-loic.poulain@linaro.org
For software-driven scan, rely on mac80211 software scan instead
of internal driver implementation. The internal implementation
cause connection trouble since it keep the antenna busy during
the entire scan duration, moreover it's only a passive scanning
(no probe request). Therefore, let mac80211 manages sw scan.
Note: we fallback to software scan if firmware does not report
scan offload support or if we need to scan the 5Ghz band (currently
not supported by the offload scan...).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598288035-19790-1-git-send-email-loic.poulain@linaro.org
Qualcomm's document "80-WL007-1 Rev. J" states that the highest rx rate for
the WCN3660 and WCN3680 on MCS 7 is 150 Mbps not the 72 Mbps stated here.
This patch fixes the data-rate declared in the 5GHz table.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680
hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802004824.1307124-1-bryan.odonoghue@linaro.org
Instead of using the firmware generated sequence number, use the one
already allocated by the mac80211 layer. This allows better control
of the sequence numbers and avoid to rely on same sequence for Data,
QOS Data and QOS Null Data packets.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-7-git-send-email-loic.poulain@linaro.org
This patch contains the following fixes:
- Use correct queue for submitting QoS packet. The queue id to use
is a one-to-one mapping with the TID.
- Don't encrypt a frame with IEEE80211_TX_INTFL_DONT_ENCRYPT flag.
- Use the 'special queue' for null packets, preventing the firmware
to submit it as AMPDU.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-5-git-send-email-loic.poulain@linaro.org
Increase the short/long retry limit to 15 in order to impove TX
robustness in noisy/busy environment. 15 is the default value
defined in the downstream driver. Observed number of ack timeout
is reduced with this change.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-4-git-send-email-loic.poulain@linaro.org
The controller is capable of reporting TX indication which can be used
to report TX ack when IEEE80211_TX_CTL_REQ_TX_STATUS is set.
The support was only partially implemented.
The firmware can be configured for reporting event when a packet is
acked, without specifying which packet though. In order to send a
packet flagged with TX status callback, we need to stop the queue,
submit the packet and wait for the firmware ack event. Then the queue
can be restarted and mac80211 status callback called.
In case the packet is not acked, no ack event will be received,
therefore a timeout mechanism is introduced to restart the queue
and call the status cb in case no event is received after a 100ms.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-3-git-send-email-loic.poulain@linaro.org
Several AMPDU sessions can be started, e.g. for different TIDs.
Currently the driver does not take care of the session ID when
requesting block-ack (statically set to 0), which leads to never
block-acked packet with sessions other than 0.
Fix this by saving the session id when creating the ba session and
use it in subsequent ba operations.
This issue can be reproduced with iperf in two steps (tid 0 strem
then tid 6 stream).
1.0 iperf -s # wcn36xx side
1.1 iperf -c ${IP_ADDR} # host side
Then
2.0 iperf -s -u -S 0xC0 # wcn36xx side
2.1 iperf -c ${IP_ADDR} -u -S 0xC0 -l 2000 # host side
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-2-git-send-email-loic.poulain@linaro.org
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507151758.GA4962@embeddedor
In case of error, 'qcom_wcnss_open_channel()' must be undone by a call to
'rpmsg_destroy_ept()', as already done in the remove function.
Fixes: 5052de8def ("soc: qcom: smd: Transition client drivers from smd to rpmsg")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507043619.200051-1-christophe.jaillet@wanadoo.fr
There is a spelling mistake in a wcn36xx_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the signal stregth decays smoothly and physical connnection
is already gone and no deauth has arrived, the qcom soc is not
able to indicate neither WCN36XX_HAL_MISSED_BEACON_IND nor
WCN36XX_HAL_MISSED_BEACON_IND. It was noticed that such situation gets
even more reproducible, when the driver fails to enter bmps mode - which is
highly likely to occur. Thus, in order to provide proper disconnection
of the connected STA, let mac80211 handle it, instead of wcn3xx driver.
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
clang triggers a warning about oversized stack frames that gcc does not
notice because of slightly different inlining decisions:
ath/wcn36xx/smd.c:1409:5: error: stack frame size of 1040 bytes in function 'wcn36xx_smd_config_bss' [-Werror,-Wframe-larger-than=]
ath/wcn36xx/smd.c:640:5: error: stack frame size of 1032 bytes in function 'wcn36xx_smd_start_hw_scan' [-Werror,-Wframe-larger-than=]
Basically the wcn36xx_hal_start_scan_offload_req_msg,
wcn36xx_hal_config_bss_req_msg_v1, and wcn36xx_hal_config_bss_req_msg
structures are too large to be put on the kernel stack, but small
enough that gcc does not warn about them.
Use kzalloc() to allocate them all. There are similar structures in other
parts of this driver, but they are all smaller, with the next largest
stack frame at 480 bytes for wcn36xx_smd_send_beacon.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit ec8f24b7fa ("treewide: Add SPDX license identifier -
Makefile/Kconfig") marked various Makefiles and Kconfig files within ath
directories as GPL-2.0. But these modules and drivers are actually ISC:
* ath
* ar5523
* ath10k
* ath5k
* ath6kl
* ath9k
* wcn36xx
* wil6210
Fix SPDX tags accordingly.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.19. Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
Initialization is unneccessary when the variable is written before it is
read. There were some occasions in which the driver would initialize `ret'
during declaration without need.
Purely a cosmetic change with no functional impact.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of WEP encryption, driver has to configure shared key for
associated station(s). Note that sta pointer is NULL in case of non
pairwise key, causing NULL pointer dereference with existing code
(sta_priv->is_data_encrypted). Fix this by using associated sta list
instead. This enables WEP support as client, WEP AP is non-functional.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add list of associated stations(STA, AP, peer...) per vif.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Older gcc (< 4.4) doesn't like files starting with a Unicode BOM:
drivers/net/wireless/ath/wcn36xx/testmode.c:1: error: stray ‘\357’ in program
drivers/net/wireless/ath/wcn36xx/testmode.c:1: error: stray ‘\273’ in program
drivers/net/wireless/ath/wcn36xx/testmode.c:1: error: stray ‘\277’ in program
Remove the BOM, the rest of the file is plain ASCII anyway.
Output of "file drivers/net/wireless/ath/wcn36xx/testmode.c" before:
drivers/net/wireless/ath/wcn36xx/testmode.c: C source, UTF-8 Unicode (with BOM) text
and after:
drivers/net/wireless/ath/wcn36xx/testmode.c: C source, ASCII text
Fixes: 87f825e6e2 ("wcn36xx: Add support for Factory Test Mode (FTM)")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce infrastructure for supporting Factory Test Mode (FTM) of the
wireless LAN subsystem. In order for the user space to access the
firmware in test mode the relevant netlink channel needs to be exposed
from the kernel driver.
The above is achieved as follows:
1) Register wcn36xx driver to testmode callback from netlink
2) Add testmode callback implementation to handle incoming FTM commands
3) Add FTM command packet structure
4) Add handling for GET_BUILD_RELEASE_NUMBER (msgid=0x32A2)
5) Add generic handling for all PTT_MSG packets
Signed-off-by: Eyal Ilsar <eilsar@codeaurora.org>
Signed-off-by: Ramon Fried <ramon.fried@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a missing newline in wcn36xx_smd_send_and_wait() and also log the
command request and response type that was processed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop the extra warning about failed allocations, both the core and the
only caller of this function will warn loud enough in such cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the interface is shut down, wcn36xx_smd_close() potentially races
against the queue worker. Make sure to cancel the work, and then free all
the remnants in hal_ind_queue manually.
This is again just a theoretical issue, not something that was triggered in
the wild.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a BSSID is joined, set the link status to 'preassoc', and set it to
'idle' when the BSS is deleted.
This is what the downstream driver is doing, and it seems to improve the
reliability during connect/disconnect stress tests.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In reap_tx_dxes(), when we iterate over the linked descriptors, only
consider such valid that have WCN36xx_DXE_CTRL_EOP set.
This is what the prima downstream driver is doing as well.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On RX and TX interrupts, check for the WCN36XX_CH_STAT_INT_ED_MASK or
WCN36XX_CH_STAT_INT_DONE_MASK in the interrupt reason register, and
only handle packets when it is set. This way, reap_tx_dxes() is only
invoked when needed.
This brings the dequeing logic in line with what the prima downstream
driver is doing.
While at it, also log the interrupt reason.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Like on the TX side, check for the interrupt reason when the RX interrupt
is latched and clear the ERR, DONE and ED masks.
This seems to help with connection timeouts and network stream
starvatations. And FWIW, the downstream driver does the same thing.
Note that in analogy to the TX side, WCN36XX_DXE_0_INT_CLR should be set to
WCN36XX_INT_MASK_CHAN_RX_{L,H} rather than WCN36XX_DXE_INT_CH{1,3}_MASK. It
did the right thing however, as the defines happen to have identical values.
Also, instead of determining register addresses and values inside
wcn36xx_rx_handle_packets(), pass them as arguments.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's no need to disable the IRQ from inside its handler.
Instead just grab the spinlock of the channel that is being processed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The device takes 32-bit addresses only, so inform the DMA API about it.
This is the default on msm8016, so that doesn't change anything, but
it's best practice to be explicit.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wcn36xx_dxe_tx_frame() is entered while the device is still processing
the queue asyncronously, we are racing against the firmware code with
updates to the buffer descriptors. Presumably, the firmware scans the ring
buffer that holds the descriptors and scans for a valid control descriptor,
and then assumes that the next descriptor contains the payload. If, however,
the control descriptor is marked valid, but the payload descriptor isn't,
the packet is not sent out.
Another issue with the current code is that is lacks memory barriers before
descriptors are marked valid. This is important because the CPU may reorder
writes to memory, even if it is allocated as coherent DMA area, and hence
the device may see incompletely written data.
To fix this, the code in wcn36xx_dxe_tx_frame() was restructured a bit so
that the payload descriptor is made valid before the control descriptor.
Memory barriers are added to ensure coherency of shared memory areas.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the wifi driver core passes IE elements in the scan request, append
them to the firmware message. The driver currently tells the core that
it is capable of attaching up to WCN36XX_MAX_SCAN_IE_LEN octets, but
doesn't actually pass them to the the hardware.
Note that this patch doesn't fix a bug that was observed. The change is
merely done for the sake of completeness as the hardware supports
appending IEs in scans. Tests show that network scans work fine with
this patch applied.
Some defines were moved around to avoid cyclic include dependencies.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pass the bss_type of the currently configured BSS in the message for the
scan request. Therefore, that setting needs to be kept in struct
wcn36xx_vif.
This seems to be only interesting when scanning for a specific SSID
and doesn't matter for regular wildcard scans.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For firmwares that don't have the SCAN_OFFLOAD feature bit set, do
not call into wcn36xx_smd_stop_hw_scan(). Instead, stop the asynchronous
work and call into ieee80211_scan_completed() immediately.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the network interface goes down while a scan request is still
pending that can't be stopped due to firmware hickups, wcn->scan_req
remains set, even though the hardware is deinitialized. This results
in -EBUSY for all scan requests after the interface was brought up
again.
Fix this by explicitly completing pending scan requests in
wcn36xx_stop().
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware sends a WCN36XX_HAL_SCAN_IND_DEQUEUED indication,
the request is apparently no longer valid. Attempts to stop the hardware
scan request subsequently will lead to the following error message, and
the hardware is no longer able to communicate with any AP:
[ 57.917186] wcn36xx: ERROR hal_stop_scan_offload response failed err=5
Interpreting this indicator message as scan abortion fixes this.
While at it, add a newline to a debug print.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware message to delete BSS keys expects a BSS index to be passed.
This field is currently hard-coded to 0. Fix this by passing in the index
we received from the firmware when the BSS was configured.
The encryption type in that message also needs to be set to what was used
when the key was set, so the assignment of vif_priv->encrypt_type is now
done after the firmware command was sent. This reportedly fixes the
following error in AP mode:
wcn36xx: ERROR hal_remove_bsskey response failed err=6
Also, AFAIU, when a BSS is deleted, the firmware apparently drops all the
keys associated with it. Trying to remove the key explicitly afterwards
will hence lead to the following message:
wcn36xx: ERROR hal_remove_bsskey response failed err=16
This is now suppressed with an extra check for the BSS index validity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When accessing shared memory to check for the stat of submitted
descriptors, make sure to use READ_ONCE(). This will guarantee the
compiler treats these memory locations as volatile and doesn't apply
any caching.
While this doesn't fix any particular problem I ran into, it's best
practice to do it this way.
Note that this patch also removes the superflous extra condition check
in the do-while loop in reap_tx_dxes(), as the loop will break
instantly anyway in that case.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
GFP_ATOMIC should only be used when the allocation is done from atomic
context. Introduce a new flag to wcn36xx_dxe_fill_skb() and use GFP_KERNEL
when pre-allocating buffers during init.
This doesn't fix an issue that was observed in the wild, but it reduces
the chance of failed allocations under memory pressure.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each DXE control block is associated to a specific channel.
The channel lock is always taken before accessing a control block.
There is no need to have an extra (useless) spinlock for the control
block skb.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This prevents GCC warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware code cannot cope with requests to remove BSS indices that have
not previously been added. This primarily happens when the device is
suspended and then resumed. ieee80211_reconfig() then calls into
wcn36xx_bss_info_changed() with an empty bssid and BSS_CHANGED_BSSID set,
which subsequently leads to a firmware crash:
[ 43.647928] qcom-wcnss-pil a204000.wcnss: fatal error received: halMsg.c:4964:halMsg_DelBss: Invalid BSSIndex 0
[ 43.647959] remoteproc remoteproc0: crash detected in a204000.wcnss: type fatal error
To fix this, set bss_index to WCN36XX_HAL_BSS_INVALID_IDX for all bss
that have not been configured in the firmware, and don't call into the
firmware with invalid indices.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wcn36xx_dxe_tx_frame() fails to transmit the TX frame, the driver
will call into ieee80211_free_txskb() for the skb in flight, so it'll no
longer be valid. Hence, we shouldn't keep a reference to it in ctl->skb.
Also, if the skb has IEEE80211_TX_CTL_REQ_TX_STATUS set, a pointer to
it will currently remain in wcn->tx_ack_skb, which will potentially lead
to a crash if accessed later.
Fix this by checking the return value of wcn36xx_dxe_tx_frame(), and
nullify wcn->tx_ack_skb again in case of errors. Move the assignment
of ctl->skb in wcn36xx_dxe_tx_frame() so it only happens when the
transmission is successful.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bail out if the mapping fails. Even though this hasn't occured during
tests, this unlikely case should still be handled.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case wcn36xx_smd_rsp_process() is called more than once before
hal_ind_work was dispatched, the messages will end up in hal_ind_queue,
but wcn36xx_ind_smd_work() will only look at the first message in that
list.
Fix this by dequeing the messages from the list in a loop, and only stop
when it's empty.
This issue was found during a review of the driver. In my tests, that
race never actually occured.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx_start_tx function retrieves the buffer descriptor from the
channel control queue to start filling tx buffer information. However,
nothing prevents this same buffer to be concurrently accessed in a
concurent tx call, leading to potential buffer coruption and firmware
crash (observed during iperf test). The channel control queue should
only be accessed and updated with the channel lock.
Fix this issue by using a local buffer descriptor which will be copied
in the thread-safe wcn36xx_dxe_tx_frame.
Note that buffer descriptor size is few bytes so the introduced copy
overhead is insignificant. Moreover, this allows to keep the locked
section minimal.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It appears that the WCN36xx firmware doesn't actually respond to
probe requests. Until it's resolved, switch the probe response
responsibility to the 802.11 layer to allow creation of
hidden SSID AP's.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
IRQ reason was not cheked for errors.
Although error handing is not currently supported, it
will be nice to output an error value to the log if the
DMA operation failed.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DXE channel defaults used hardcoded magic values.
Added bit definitions of the control register and
calculate this values in compilation for clarity.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DXE descriptor control registers used hardcoded magic values. Added bit
definitions of the control register and calculate this values in compilation
for clarity. No functional changes.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the WLAN interface is started the FW
version and caps are printed.
The caps now will be displayed only in debug mode.
Firmware version will be displayed only once on first
startup of the interface.
Change-Id: I4db6ea7f384fe15eebe4c3ddb1d1ccab00094332
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wcn36xx_cancel_hw_scan method stops the hw scan and notify the
scan completion via ieee80211_scan_completed.
However, on scan offload cancellation, firmware sends a scan complete
indication, triggering a new call to ieee80211_scan_completed.
This leads to kernel warn since the scan has already been completed.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx_dxe_init() doesn't check for the return value of
wcn36xx_dxe_init_descs(), release the resources in case an error ocurred.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaWd2WAAoJEG4XJFUm622bDnsH/2+Y5MEn31xvv7FGP46dHCNB
wk1SgcQOQdb7taIpZ++tFvhTQOXwrtGMA5iAFLeg9+07tqGIaZQqr58aab7BCQTi
2PgUK9sEdI5LPw3KmhnaqfHMVDKMaYdjcAhLG4FzJqMoDfTuPr56Vnnde3J2A0mj
hhFRarNKBArEvRaWtNypdZQN8HM10v3LJq+HNnK/yep7fW2EuwSwTO2YBqDhrwAD
0gzfV6yi05497uVv6W+5CKRawu7RoYgbFTaEa8rmCViIjf9bK4gPdsW18a/DTNMz
MfvLF2RQZk1k944+a+a983oqZNkq9dEWd0kF0CSFgbO3r/SO7264yc4PHpZKy/s=
=2eQ4
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
The second assignment to msg_body.min_ch_time is incorrect, it
should actually be to msg_body.max_ch_time.
Thanks to Bjorn Andersson for identifying the correct way to fix
this as my original fix was incorrect.
Detected by CoverityScan, CID#1463042 ("Unused Value")
Fixes: 2f3bef4b24 ("wcn36xx: Add hardware scan offload support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since driver does not report hardware dynamic power saving cap,
this is up to the mac80211 to manage power saving timeout and
state machine, using the ieee80211 config callback to report
PS changes. This patch enables/disables PS mode according to
the new configuration.
Remove old behaviour enabling PS mode in a static way, this make
the device unusable when power save is enabled since device is
forced to PS regardless RX/TX traffic.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The purpose of pushing indication on a list and handle these in a
separate worker is to allow the handlers to sleep. It does therefor not
make much sense to hold the queue spinlock through the entire indication
worker function.
By removing items from the queue early we don't need to hold the lock
throughout the indication worker, allowing the individual handlers to
sleep.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current hw_scan implementation does not trigger offloaded
hardware scan and seems to only put the device in a kind of
listening mode (beacon/probe-response) for software scan.
Since no probe request are generated by the software, current
scanning method is similar to a passive scan.
This patch introduces support for 'true' hardware offloaded scan.
Hardware scan is configured and started via the start-scan-offload
firmware message. Once scan has been completed a scan indicator
message is received from firmware.
Moreover, this patch includes support for directed probe-request,
allowing connection with hidden APs. It also fixes scan issues with
band-steering AP which are not 'visible' with passive scan (due to
hidden ssid in beacons).
Let's keep the 'legacy' scanning method in case scan-offload is not
supported.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the value for the firmware configuration parameters
BTC_STATIC_LEN_LE_BT and BTC_STATIC_LEN_LE_WLAN are not set the duty
cycle between BT and WLAN is such that if BT (including BLE) is active
WLAN gets 0 bandwidth. When tuning these parameters having a too high
value for WLAN means that BLE performance degrades.
The "sweet" point of roughly half of the maximal values was empirically
found to achieve a balance between BLE and Wi-Fi coexistence
performance.
Signed-off-by: Eyal Ilsar <eilsar@codeaurora.org>
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mmio node was also prematurely freed.
Fixes: fd52bdae9a ("wcn36xx: Disable 5GHz for wcn3620")
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No rcu_read_lock is called, but rcu_read_unlock is still called.
Thus rcu_read_unlock should be removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wcn3620 can only operate on 2.4GHz band due to RF limitation.
If wcn36xx digital block is associated with an external IRIS
RF module, retrieve the id and disable 5GHz band in case of
wcn3620 id.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As the association status changes the driver needs to configure the
hardware. This is done based on information in the "sta" acquired by
ieee80211_find_sta(), which requires the caller to ensure that the "sta"
is valid while its being used; generally by entering an rcu read
section.
But the operations acting on the "sta" has to communicate with the
firmware and may therefor sleep, resulting in the following report:
[ 31.418190] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:238
[ 31.425919] in_atomic(): 0, irqs_disabled(): 0, pid: 34, name:
kworker/u8:1
[ 31.434609] CPU: 0 PID: 34 Comm: kworker/u8:1 Tainted: G W
4.12.0-rc4-next-20170607+ #993
[ 31.441002] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC
(DT)
[ 31.450380] Workqueue: phy0 ieee80211_iface_work
[ 31.457226] Call trace:
[ 31.461830] [<ffffff8008088c58>] dump_backtrace+0x0/0x260
[ 31.464004] [<ffffff8008088f7c>] show_stack+0x14/0x20
[ 31.469557] [<ffffff8008392e70>] dump_stack+0x98/0xb8
[ 31.474592] [<ffffff80080e4330>] ___might_sleep+0xf0/0x118
[ 31.479626] [<ffffff80080e43a8>] __might_sleep+0x50/0x88
[ 31.485010] [<ffffff80088ff9a4>] mutex_lock+0x24/0x60
[ 31.490479] [<ffffff8008595c38>] wcn36xx_smd_set_link_st+0x30/0x130
[ 31.495428] [<ffffff8008591ed8>] wcn36xx_bss_info_changed+0x148/0x448
[ 31.501504] [<ffffff80088ab3c4>]
ieee80211_bss_info_change_notify+0xbc/0x118
[ 31.508102] [<ffffff80088f841c>] ieee80211_assoc_success+0x664/0x7f8
[ 31.515220] [<ffffff80088e13d4>]
ieee80211_rx_mgmt_assoc_resp+0x144/0x2d8
[ 31.521555] [<ffffff80088e1e20>]
ieee80211_sta_rx_queued_mgmt+0x190/0x698
[ 31.528239] [<ffffff80088bc44c>] ieee80211_iface_work+0x234/0x368
[ 31.535011] [<ffffff80080d81ac>] process_one_work+0x1cc/0x340
[ 31.541086] [<ffffff80080d8368>] worker_thread+0x48/0x430
[ 31.546814] [<ffffff80080de448>] kthread+0x108/0x138
[ 31.552195] [<ffffff8008082ec0>] ret_from_fork+0x10/0x50
In order to ensure that the "sta" remains alive (and consistent) for the
duration of bss_info_changed() mutual exclusion has to be ensured with
sta_remove().
This is done by introducing a mutex to cover firmware configuration
changes, which is made to also ensure mutual exclusion between other
operations changing the state or configuration of the firmware. With
this we can drop the rcu read lock.
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The SMD channel is not the primary WCNSS channel and must explicitly be
closed as the device is removed, or the channel will already by open on
a subsequent probe call in e.g. the case of reloading the kernel module.
This issue was introduced because I simplified the underlying SMD
implementation while the SMD adaptions of the driver sat on the mailing
list, but missed to update these patches. The patch does however only
apply back to the transition to rpmsg, hence the limited Fixes.
Fixes: 5052de8def ("soc: qcom: smd: Transition client drivers from smd to rpmsg")
Reported-by: Eyal Ilsar <c_eilsar@qti.qualcomm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
-----BEGIN PGP SIGNATURE-----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=f4VT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY55+nAAoJEG4XJFUm622bRUAIAJfCM5YFyh9Y/XV147JshdGi
xScDAgwIA1/o+iHfvTsjSH3/uoH3JhsiqfcXN7R80kyvG7HrUeXaebmUDgbBvOOj
FTMuytiD+xkgEKVjWIwtXUYqctyzQ8ofxIQJ2W5E9CbEYAZ43uEcXzdnhBKVaVuY
XPw59MF5vRGDDXTnTf4af4OC+L1QqwUqsyi4j7oMIfexieMGQxQL0JYOyHweCnCV
gMz/kTxAIcmC1yOiunu8VyU4kK8borW36wC7XEE3MOXhqSKnQjyhI/efA76AKX0j
O7sfEKCFlZU1xXQbkB9ecbKc2jyMefiE0gwLWWI5dwKhnUS2qQ6GS8ML+NMfV0g=
=B2X+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
By moving these client drivers to use RPMSG instead of the direct SMD
API we can reuse them ontop of the newly added GLINK wire-protocol
support found in the 820 and 835 Qualcomm platforms.
As the new (RPMSG-based) and old SMD implementations are mutually
exclusive we have to change all client drivers in one commit, to make
sure we have a working system before and after this transition.
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder 'out_free_dxe_pool' and 'out_free_dxe_ctl' error handling labels
in order to match the way resources have been allocated.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature
wholesale in all mac80211-based drivers that do not set the
IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will
be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and
will detect when the thresholds set by
ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few)
drivers need code to enable the firmware to monitor the thresholds.
This is mostly only compile-tested.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the even that the wcn36xx interface is brought down while a hw_scan
is active we must abort and wait for the ongoing scan to signal
completion to mac80211.
Reported-by: Mart Raudsepp <leio@gentoo.org>
Fixes: 886039036c ("wcn36xx: Implement firmware assisted scan")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ieee80211_unregister_hw() might invoke operations to stop the interface,
that uses the hal_mutex. So don't destroy it until after we're done
using it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware versions sends a "print register indication", handle this
by printing out the content.
Cc: Nicolas Dechesne <ndec@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using the software based channel scan mechanism from mac80211 keeps us
offline for 10-15 second, we should instead issue a start_scan/end_scan
on each channel reducing this time.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wcn36xx wifi driver follows the life cycle of the WLAN_CTRL SMD
channel, as such it should be a SMD client. This patch makes this
transition, now that we have the necessary frameworks available.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes the firmware sends a HAL_DEL_BA_IND, the prima driver silently
ignore this message so let's do the same to silence the error message.
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix up the wcn36xx_smd_update_scan_params() to work with non-ancient
versions of the firmware and support actually specifying the list of
channels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The CCU block in WCNSS is configured for appropriate routing of
interrupts from the DXE to the application cpu, this is not dependant on
the iris version (wcn3660 vs wcn3680), but rather if the SoC has a riva
or pronto built in.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the wcnss mmio space into explicit regions for ccu and dxe and
acquire these from the node referenced by the qcom,mmio phandle.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for handling incoming messages from IRQ context, change
the indication list lock to a spinlock
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Merge the two allocation instead of separately allocating room for the
indication payload.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After booting the wireless subsystem and uploading the NV blob to the
WCNSS_CTRL service the remote continues to do things and will not start
servicing wlan-requests for another 2-5 seconds (measured).
The downstream code does not have any special handling for this case,
but has a timeout of 10 seconds for the communication layer. By
extending the wcn36xx timeout to match this we follows the same flow for
the boot procedure and can successfully configure WiFi as wlan0 is
registered.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.7. Major changes:
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
Fill in the capability list with more values from the downstream driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The WCN36XX_HAL_RMV_BSSKEY_RSP carries a single u32 with "status", so we
can use the standard status check function for decoding the result.
This is the last user of the v2 status checker, so remove the struct and
helper function.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
