Configure multiple BSSID flags and index of the transmitting interface
in vdev create/start commands depending on the service bit
WMI_TLV_SERVICE_MBSS_PARAM_IN_VDEV_START_SUPPORT.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230405221648.17950-3-quic_alokad@quicinc.com
Advertise the driver support for multiple BSSID (MBSSID) and
enhanced multi-BSSID advertisements (EMA) by setting extended
capabilities.
Configure mbssid_max_interfaces and ema_max_profile_periodicity
fields in structure wiphy which are used to advertise maximum number
of interfaces and profile periodicity supported by the driver.
Add new WMI fields to configure maximum vdev count supported for
MBSSID and profile periodicity in case of EMA.
Setting WMI_RSRC_CFG_FLAG2_CALC_NEXT_DTIM_COUNT_SET flag
indicates that the firmware should track and update the DTIM counts
for each non-transmitted profile.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230405221648.17950-2-quic_alokad@quicinc.com
In a rare arm64 randconfig build, I got multiple warnings for ath11k
and ath12k:
In function 'ath11k_peer_assoc_h_ht',
inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:2665:2:
drivers/net/wireless/ath/ath11k/mac.c:1709:13: error: 'ath11k_peer_assoc_h_ht_masked' reading 10 bytes from a region of size 0 [-Werror=stringop-overread]
1709 | if (ath11k_peer_assoc_h_ht_masked(ht_mcs_mask))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This happens whenever gcc-13 fails to inline one of the functions
that take a fixed-length array argument but gets passed a pointer.
Change these functions to all take a regular pointer argument
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230417205447.1800912-1-arnd@kernel.org
ath11k_wmi_fw_stats_num_vdevs() and ath11k_wmi_fw_stats_num_bcn() really
look the same as list_count_nodes(), so use the latter instead of hand
writing it.
The first ones use list_for_each_entry() and the other list_for_each(), but
they both count the number of nodes in the list.
While at it, also remove to prototypes of non-existent functions.
Based on the names and prototypes, it is likely that they should be
equivalent to list_count_nodes().
Compile tested only.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/941484caae24b89d20524b1a5661dd1fd7025492.1682542084.git.christophe.jaillet@wanadoo.fr
Most likely the last -next pull request for v6.4. We have changes all
over. rtw88 now supports SDIO bus and iwlwifi continues to work on
Wi-Fi 7 support. Not much stack changes this time.
Major changes:
cfg80211/mac80211
* fix some Fine Time Measurement (FTM) frames not being bufferable
* flush frames before key removal to avoid potential unencrypted
transmission depending on the hardware design
iwlwifi
* preparation for Wi-Fi 7 EHT and multi-link support
rtw88
* SDIO bus support
* RTL8822BS, RTL8822CS and RTL8821CS SDIO chipset support
rtw89
* framework firmware backwards compatibility
brcmfmac
* Cypress 43439 SDIO support
mt76
* mt7921 P2P support
* mt7996 mesh A-MSDU support
* mt7996 EHT support
* mt7996 coredump support
wcn36xx
* support for pronto v3 hardware
ath11k
* PCIe DeviceTree bindings
* WCN6750: enable SAR support
ath10k
* convert DeviceTree bindings to YAML
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmRCaTURHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZvcRwf+NcLS4HbmqGZhBxl2LZVZ6AFCBM4ijDlO
pxdMiC4UxT+UApY1/9YXo0VS97M7paDJH+R/g1HcTvvKURHCmsdhYHm+R1MH+/uD
r8RfvJg4VtNnlUpsJh9jxt+e697KP15M7DF0sFlQzdIoTUl13Hp7YhI76zunAbAN
u1FBcVVJiCcJWbLolMzqAeBMUWUEG+GtHF6Zn5kChVU/p1nmwJMPUG3Qvb61a7Yc
BM1pQX8jQ8PBj+VrGPGvqX0BOdbxq0evauYScq2oTOhQ1fzTNWOsI1yI7AwApptR
itwQ2t1UK/C/EWpvWIBSd0nit1uwSx0Zsu/nSZlbKbrvIFwd5XnfwQ==
=Irrd
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.4
Most likely the last -next pull request for v6.4. We have changes all
over. rtw88 now supports SDIO bus and iwlwifi continues to work on
Wi-Fi 7 support. Not much stack changes this time.
Major changes:
cfg80211/mac80211
- fix some Fine Time Measurement (FTM) frames not being bufferable
- flush frames before key removal to avoid potential unencrypted
transmission depending on the hardware design
iwlwifi
- preparation for Wi-Fi 7 EHT and multi-link support
rtw88
- SDIO bus support
- RTL8822BS, RTL8822CS and RTL8821CS SDIO chipset support
rtw89
- framework firmware backwards compatibility
brcmfmac
- Cypress 43439 SDIO support
mt76
- mt7921 P2P support
- mt7996 mesh A-MSDU support
- mt7996 EHT support
- mt7996 coredump support
wcn36xx
- support for pronto v3 hardware
ath11k
- PCIe DeviceTree bindings
- WCN6750: enable SAR support
ath10k
- convert DeviceTree bindings to YAML
* tag 'wireless-next-2023-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (261 commits)
wifi: rtw88: Update spelling in main.h
wifi: airo: remove ISA_DMA_API dependency
wifi: rtl8xxxu: Simplify setting the initial gain
wifi: rtl8xxxu: Add rtl8xxxu_write{8,16,32}_{set,clear}
wifi: rtl8xxxu: Don't print the vendor/product/serial
wifi: rtw88: Fix memory leak in rtw88_usb
wifi: rtw88: call rtw8821c_switch_rf_set() according to chip variant
wifi: rtw88: set pkg_type correctly for specific rtw8821c variants
wifi: rtw88: rtw8821c: Fix rfe_option field width
wifi: rtw88: usb: fix priority queue to endpoint mapping
wifi: rtw88: 8822c: add iface combination
wifi: rtw88: handle station mode concurrent scan with AP mode
wifi: rtw88: prevent scan abort with other VIFs
wifi: rtw88: refine reserved page flow for AP mode
wifi: rtw88: disallow PS during AP mode
wifi: rtw88: 8822c: extend reserved page number
wifi: rtw88: add port switch for AP mode
wifi: rtw88: add bitmap for dynamic port settings
wifi: rtw89: mac: use regular int as return type of DLE buffer request
wifi: mac80211: remove return value check of debugfs_create_dir()
...
====================
Link: https://lore.kernel.org/r/20230421104726.800BCC433D2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a regression fix for 80+80 and 160 MHz support bits being
cleared, therefore not adverised. Remove disable of 80+80 and 160 MHz
capability flags and assign valid center frequency 2 similar to
VHT80_80.
Fixes: 38dfe775d0 ("wifi: ath11k: push MU-MIMO params from hostapd to hardware")
Reported-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Robert Marko <robert.marko@sartura.hr> # IPQ8074 WLAN.HK.2.9.0.1-01385-QCAHKSWPL_SILICONZ-1
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217299
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1681762947-13882-1-git-send-email-quic_msinada@quicinc.com
While running traffics for a long time, randomly an RX descriptor
filled with value "0" from REO destination ring is received.
This descriptor which is invalid causes the wrong SKB (SKB stored in
the IDR lookup with buffer id "0") to be fetched which in turn
causes SKB memory corruption issue and the same leads to crash
after some time.
Changed the start id for idr allocation to "1" and the buffer id "0"
is reserved for error validation. Introduced Sanity check to validate
the descriptor, before processing the SKB.
Crash Signature :
Unable to handle kernel paging request at virtual address 3f004900
PC points to "b15_dma_inv_range+0x30/0x50"
LR points to "dma_cache_maint_page+0x8c/0x128".
The Backtrace obtained is as follows:
[<8031716c>] (b15_dma_inv_range) from [<80313a4c>] (dma_cache_maint_page+0x8c/0x128)
[<80313a4c>] (dma_cache_maint_page) from [<80313b90>] (__dma_page_dev_to_cpu+0x28/0xcc)
[<80313b90>] (__dma_page_dev_to_cpu) from [<7fb5dd68>] (ath11k_dp_process_rx+0x1e8/0x4a4 [ath11k])
[<7fb5dd68>] (ath11k_dp_process_rx [ath11k]) from [<7fb53c20>] (ath11k_dp_service_srng+0xb0/0x2ac [ath11k])
[<7fb53c20>] (ath11k_dp_service_srng [ath11k]) from [<7f67bba4>] (ath11k_pci_ext_grp_napi_poll+0x1c/0x78 [ath11k_pci])
[<7f67bba4>] (ath11k_pci_ext_grp_napi_poll [ath11k_pci]) from [<807d5cf4>] (__napi_poll+0x28/0xb8)
[<807d5cf4>] (__napi_poll) from [<807d5f28>] (net_rx_action+0xf0/0x280)
[<807d5f28>] (net_rx_action) from [<80302148>] (__do_softirq+0xd0/0x280)
[<80302148>] (__do_softirq) from [<80320408>] (irq_exit+0x74/0xd4)
[<80320408>] (irq_exit) from [<803638a4>] (__handle_domain_irq+0x90/0xb4)
[<803638a4>] (__handle_domain_irq) from [<805bedec>] (gic_handle_irq+0x58/0x90)
[<805bedec>] (gic_handle_irq) from [<80301a78>] (__irq_svc+0x58/0x8c)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403191533.28114-1-quic_nmaran@quicinc.com
ieee80211_tx_status() treats packets in 802.11 frame format and
tries to extract sta address from packet header. When tx encap
offload is enabled, this becomes invalid operation. Hence, switch
to using ieee80211_tx_status_ext() after filling in station
address for handling both 802.11 and 802.3 frames.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403195738.25367-2-quic_pradeepc@quicinc.com
During reo command failure, the peer mac detail for which the reo
command was not successful is unknown. Hence, to improve the
debuggability, add the peer mac information in the failure cases
which would be useful during multi client cases.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403182420.23375-4-quic_hprem@quicinc.com
Prevent REO cmd failures causing double free by increasing REO cmd
ring size and moving REO status ring mask to IRQ group 3 from group
0 to separate from tx completion ring on IRQ group 0 which may delay
reo status processing.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403182420.23375-3-quic_hprem@quicinc.com
Peer rx_tid is locally copied thrice during peer_rx_tid_cleanup to
send REO_CMD_UPDATE_RX_QUEUE followed by REO_CMD_FLUSH_CACHE to flush
all aged REO descriptors from HW cache.
When sending REO_CMD_FLUSH_CACHE fails, we do dma unmap of already
mapped rx_tid->vaddr and free it. This is not checked during
reo_cmd_list_cleanup() and dp_reo_cmd_free() before trying to free and
unmap again.
Fix this by setting rx_tid->vaddr NULL in rx tid delete and also
wherever freeing it to check in reo_cmd_list_cleanup() and
reo_cmd_free() before trying to free again.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403182420.23375-2-quic_hprem@quicinc.com
"__fls" would have an undefined behavior if the argument is passed
as "0". Hence, added changes to handle the same.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403184155.8670-3-quic_nmaran@quicinc.com
When max virtual ap interfaces are configured in all the bands with
ACS and hostapd restart is done every 60s, a crash is observed at
random times.
In this certain scenario, a fragmented packet is received for
self peer, for which rx_tid and rx_frags are not initialized in
datapath. While handling this fragment, crash is observed as the
rx_frag list is uninitialised and when we walk in
ath11k_dp_rx_h_sort_frags, skb null leads to exception.
To address this, before processing received fragments we check
dp_setup_done flag is set to ensure that peer has completed its
dp peer setup for fragment queue, else ignore processing the
fragments.
Call trace:
ath11k_dp_process_rx_err+0x550/0x1084 [ath11k]
ath11k_dp_service_srng+0x70/0x370 [ath11k]
0xffffffc009693a04
__napi_poll+0x30/0xa4
net_rx_action+0x118/0x270
__do_softirq+0x10c/0x244
irq_exit+0x64/0xb4
__handle_domain_irq+0x88/0xac
gic_handle_irq+0x74/0xbc
el1_irq+0xf0/0x1c0
arch_cpu_idle+0x10/0x18
do_idle+0x104/0x248
cpu_startup_entry+0x20/0x64
rest_init+0xd0/0xdc
arch_call_rest_init+0xc/0x14
start_kernel+0x480/0x4b8
Code: f9400281 f94066a2 91405021 b94a0023 (f9406401)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403184155.8670-2-quic_nmaran@quicinc.com
As there are a few more models supported by the driver, let's add the
missing MODULE_FIRMWARE() entries for them. The lack of them resulted
in the missing device enablement on some systems, such as the
installation image of openSUSE.
While we are at it, use the wildcard instead of listing each firmware
files individually for each.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230330143718.19511-1-tiwai@suse.de
Currently, SAR is enabled only on WCN6855, enable this for WCN6750 too. This
functionality gets triggered, when the user space application calls
NL80211_CMD_SET_SAR_SPECS.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230328113455.11252-1-quic_youghand@quicinc.com
Host might receive spectral events during interface
down sequence and this might create below errors.
failed to handle dma buf release event -22
failed to handle dma buf release event -22
Fix this by disabling spectral config during remove interface.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230328071150.29645-1-quic_tamizhr@quicinc.com
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323112613.7550-1-cai.huoqing@linux.dev
Firmwares advertising the support of triggering 11d algorithm on the
scan results of a regular scan expects driver to send
WMI_11D_SCAN_START_CMDID before sending WMI_START_SCAN_CMDID.
Triggering 11d algorithm on the scan results of a normal scan helps
in completely avoiding a separate 11d scan for determining regdomain.
This indirectly helps in speeding up connections on station
interfaces on the chipsets supporting 11D scan.
To enable this feature, send WMI_11D_SCAN_START_CMDID just before
sending WMI_START_SCAN_CMDID if the firmware advertises
WMI_TLV_SERVICE_SUPPORT_11D_FOR_HOST_SCAN service flag.
WCN6750 & WCN6855 supports this feature.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01160-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230315161817.29627-1-quic_mpubbise@quicinc.com
While initializing spectral, the magic value is getting written to the
invalid memory address leading to random boot-up crash. This occurs
due to the incorrect index increment in ath11k_dbring_fill_magic_value
function. Fix it by replacing the existing logic with memset32 to ensure
there is no invalid memory access.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Fixes: d3d358efc5 ("ath11k: add spectral/CFR buffer validation support")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230321052900.16895-1-quic_ppranees@quicinc.com
The WMI management rx event has multiple arrays of TLVs, however the common
WMI TLV parser won't handle multiple TLV tags of same type.
So the multiple array tags of WMI management rx TLV is parsed incorrectly
and the length calculated becomes wrong when the target sends multiple
array tags.
Add separate TLV parser to handle multiple arrays for WMI management rx
TLV. This fixes invalid length issue when the target sends multiple array
tags.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230320133840.30162-1-quic_nmaran@quicinc.com
In QCN9074, station dump signal values display default value which
is -95 dbm, since there is firmware header change for HAL_RX_MPDU_START
between QCN9074 and IPQ8074 which cause wrong peer_id fetch from msdu.
Fix this by updating hal_rx_mpdu_info with corresponding QCN9074 tlv
format.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230320110312.20639-1-quic_ppranees@quicinc.com
Fine Time Measurement(FTM) is offloaded feature to firmware.
Hence, the configuration of FTM responder role is done using
firmware capability flag instead of hw param.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ganesh Babu Jothiram <quic_gjothira@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230317072034.8217-1-quic_gjothira@quicinc.com
Currently, time taken to scan all supported channels on WCN6750
is ~8 seconds and connection time is almost 10 seconds. WCN6750
supports three Wi-Fi bands (i.e., 2.4/5/6 GHz) and the numbers of
channels for scan come around ~100 channels (default case).
Since the chip doesn't have support for DBS (Dual Band Simultaneous),
scans cannot be parallelized resulting in longer scan times.
Among the 100 odd channels, ~60 channels are in 6 GHz band. Therefore,
optimizing the scan for 6 GHz channels will bring down the overall
scan time.
WCN6750 firmware has support to scan a 6 GHz channel based on co-located
AP information i.e., RNR IE which is found in the legacy 2.4/5 GHz scan
results. When a scan request with all supported channel list is enqueued
to the firmware, then based on WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND
scan channel flag, firmware will scan only those 6 GHz channels for which
RNR IEs are found in the legacy scan results.
In the proposed design, based on NL80211_SCAN_FLAG_COLOCATED_6GHZ scan
flag, driver will set the WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND flag
for non-PSC channels. Since there is high probability to find 6 GHz APs
on PSC channels, these channels are always scanned. Only non-PSC channels
are selectively scanned based on cached RNR information from the legacy
scan results.
If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set in the scan flags,
then scan will happen on all supported channels (default behavior).
With these optimizations, scan time is improved by 1.5-1.8 seconds on
WCN6750. Similar savings have been observed on WCN6855.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323060913.10097-1-quic_mpubbise@quicinc.com
Currently ath11k breaks after hibernation, the reason being that ath11k expects
that the wireless device will have power during suspend and the firmware will
continue running. But of course during hibernation the power from the device is
cut off and firmware is not running when resuming, so ath11k will fail.
(The reason why ath11k needs the firmware running is the interaction between
mac80211 and MHI stack, it's a long story and more info in the bugzilla report.)
In SUSE kernels the watchdog timeout is reduced from the default 120 to 60 seconds:
CONFIG_DPM_WATCHDOG_TIMEOUT=60
But as the ath11k MHI timeout is 90 seconds the kernel will crash before will
ath11k will recover in resume callback. To avoid the crash reduce the MHI
timeout to just 20 seconds.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214649
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230329162038.8637-1-kvalo@kernel.org
Perform dma_sync_single_for_cpu() on monitor ring rx buffer before
reading BUFFER_DONE tag and do dma_unmap_single() only after device
had set BUFFER_DONE tag to the buffer.
Also when BUFFER_DONE tag is not set, allow the buffer to get read
next time without freeing skb.
This helps to fix AP+Monitor VAP with flood traffic scenario to see
monitor ring rx buffer overrun missing BUFFER_DONE tag to be set.
Also remove redundant rx dma buf free performed on DP
rx_mon_status_refill_ring.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230309164434.32660-1-quic_hprem@quicinc.com
Currently, in ath11k_ahb_fw_resources_init(), iommu domain
mapping is done only for the chipsets having fixed firmware
memory. Also, for such chipsets, mapping is done only if it
does not have TrustZone support.
During deinitialization, only if TrustZone support is not there,
iommu is unmapped back. However, for non fixed firmware memory
chipsets, TrustZone support is not there and this makes the
condition check to true and it tries to unmap the memory which
was not mapped during initialization.
This leads to the following trace -
[ 83.198790] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
[ 83.259537] Modules linked in: ath11k_ahb ath11k qmi_helpers
.. snip ..
[ 83.280286] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 83.287228] pc : __iommu_unmap+0x30/0x140
[ 83.293907] lr : iommu_unmap+0x5c/0xa4
[ 83.298072] sp : ffff80000b3abad0
.. snip ..
[ 83.369175] Call trace:
[ 83.376282] __iommu_unmap+0x30/0x140
[ 83.378541] iommu_unmap+0x5c/0xa4
[ 83.382360] ath11k_ahb_fw_resource_deinit.part.12+0x2c/0xac [ath11k_ahb]
[ 83.385666] ath11k_ahb_free_resources+0x140/0x17c [ath11k_ahb]
[ 83.392521] ath11k_ahb_shutdown+0x34/0x40 [ath11k_ahb]
[ 83.398248] platform_shutdown+0x20/0x2c
[ 83.403455] device_shutdown+0x16c/0x1c4
[ 83.407621] kernel_restart_prepare+0x34/0x3c
[ 83.411529] kernel_restart+0x14/0x74
[ 83.415781] __do_sys_reboot+0x1c4/0x22c
[ 83.419427] __arm64_sys_reboot+0x1c/0x24
[ 83.423420] invoke_syscall+0x44/0xfc
[ 83.427326] el0_svc_common.constprop.3+0xac/0xe8
[ 83.430974] do_el0_svc+0xa0/0xa8
[ 83.435659] el0_svc+0x1c/0x44
[ 83.438957] el0t_64_sync_handler+0x60/0x144
[ 83.441910] el0t_64_sync+0x15c/0x160
[ 83.446343] Code: aa0103f4 f9400001 f90027a1 d2800001 (f94006a0)
[ 83.449903] ---[ end trace 0000000000000000 ]---
This can be reproduced by probing an AHB chipset which is not
having a fixed memory region. During reboot (or rmmod) trace
can be seen.
Fix this issue by adding a condition check on firmware fixed memory
hw_param as done in the counter initialization function.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: f9eec4947a ("ath11k: Add support for targets without trustzone")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230309095308.24937-1-quic_adisi@quicinc.com
Zero-length arrays as fake flexible arrays are deprecated and we are
moving towards adopting C99 flexible-array members instead.
Address 25 of the following warnings found with GCC-13 and
-fstrict-flex-arrays=3 enabled:
drivers/net/wireless/ath/ath11k/debugfs_htt_stats.c:30:51: warning: array subscript <unknown> is outside array bounds of ‘const u32[0]’ {aka ‘const unsigned int[]’} [-Warray-bounds=]
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/21
Link: https://github.com/KSPP/linux/issues/266
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/ZAe5L5DtmsQxzqRH@work
ath.git patches for v6.4. Major changes:
ath10k
* enable threaded napi on WCN3990
ath11k
* push MU-MIMO params from hostapd to hardware
* tx ack signal support for management packets
Add some more debug prints in processing regulatory WMI event in order to
increase more debuggability.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-4-quic_adisi@quicinc.com
In order to support different power levels of 6 GHz AP and client,
new WMI event for regulatory - WMI_REG_CHAN_LIST_CC_EXT_EVENTID is
added in firmware. This event provides new parameters required for
6 GHz regulatory rules.
Add support for parsing 2.4 GHz, 5 GHz and 6 GHz reg rules and other
parameters from WMI_REG_CHAN_LIST_CC_EXT_EVENTID.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <quic_lavaks@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-3-quic_adisi@quicinc.com
Currently, during regulatory event, 2 GHz/5 GHz is referred
to as 2G/5G including variable names. However, there is no
such entity as 2G or 5G.
Re-name such occurences to its proper name. No functional changes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-2-quic_adisi@quicinc.com
Add support to notify tx ack signal values for management
packets to userspace through nl80211 interface.
Advertise NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT flag
to enable this feature and it will be used for data
packets as well.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Abinaya Kalaiselvan <quic_akalaise@quicinc.com>
Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221219053844.4084486-1-quic_mkenna@quicinc.com
Current release - regressions:
- phy: multiple fixes for EEE rework
- wifi: wext: warn about usage only once
- wifi: ath11k: allow system suspend to survive ath11k
Current release - new code bugs:
- mlx5: Fix memory leak in IPsec RoCE creation
- ibmvnic: assign XPS map to correct queue index
Previous releases - regressions:
- netfilter: ip6t_rpfilter: Fix regression with VRF interfaces
- netfilter: ctnetlink: make event listener tracking global
- nf_tables: allow to fetch set elements when table has an owner
- mlx5:
- fix skb leak while fifo resync and push
- fix possible ptp queue fifo use-after-free
Previous releases - always broken:
- sched: fix action bind logic
- ptp: vclock: use mutex to fix "sleep on atomic" bug if driver
also uses a mutex
- netfilter: conntrack: fix rmmod double-free race
- netfilter: xt_length: use skb len to match in length_mt6,
avoid issues with BIG TCP
Misc:
- ice: remove unnecessary CONFIG_ICE_GNSS
- mlx5e: remove hairpin write debugfs files
- sched: act_api: move TCA_EXT_WARN_MSG to the correct hierarchy
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ko4p
-----END PGP SIGNATURE-----
Merge tag 'net-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless and netfilter.
The notable fixes here are the EEE fix which restores boot for many
embedded platforms (real and QEMU); WiFi warning suppression and the
ICE Kconfig cleanup.
Current release - regressions:
- phy: multiple fixes for EEE rework
- wifi: wext: warn about usage only once
- wifi: ath11k: allow system suspend to survive ath11k
Current release - new code bugs:
- mlx5: Fix memory leak in IPsec RoCE creation
- ibmvnic: assign XPS map to correct queue index
Previous releases - regressions:
- netfilter: ip6t_rpfilter: Fix regression with VRF interfaces
- netfilter: ctnetlink: make event listener tracking global
- nf_tables: allow to fetch set elements when table has an owner
- mlx5:
- fix skb leak while fifo resync and push
- fix possible ptp queue fifo use-after-free
Previous releases - always broken:
- sched: fix action bind logic
- ptp: vclock: use mutex to fix "sleep on atomic" bug if driver also
uses a mutex
- netfilter: conntrack: fix rmmod double-free race
- netfilter: xt_length: use skb len to match in length_mt6, avoid
issues with BIG TCP
Misc:
- ice: remove unnecessary CONFIG_ICE_GNSS
- mlx5e: remove hairpin write debugfs files
- sched: act_api: move TCA_EXT_WARN_MSG to the correct hierarchy"
* tag 'net-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (53 commits)
tcp: tcp_check_req() can be called from process context
net: phy: c45: fix network interface initialization failures on xtensa, arm:cubieboard
xen-netback: remove unused variables pending_idx and index
net/sched: act_api: move TCA_EXT_WARN_MSG to the correct hierarchy
net: dsa: ocelot_ext: remove unnecessary phylink.h include
net: mscc: ocelot: fix duplicate driver name error
net: dsa: felix: fix internal MDIO controller resource length
net: dsa: seville: ignore mscc-miim read errors from Lynx PCS
net/sched: act_sample: fix action bind logic
net/sched: act_mpls: fix action bind logic
net/sched: act_pedit: fix action bind logic
wifi: wext: warn about usage only once
wifi: mt76: usb: fix use-after-free in mt76u_free_rx_queue
qede: avoid uninitialized entries in coal_entry array
nfc: fix memory leak of se_io context in nfc_genl_se_io
ice: remove unnecessary CONFIG_ICE_GNSS
net/sched: cls_api: Move call to tcf_exts_miss_cookie_base_destroy()
ibmvnic: Assign XPS map to correct queue index
docs: net: fix inaccuracies in msg_zerocopy.rst
tools: net: add __pycache__ to gitignore
...
Generate rx and tx mcs maps in ath11k_mac_set_hemcsmap() and set them
in supported mcs/nss for HE capabilities.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00356-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1666128501-12364-5-git-send-email-quic_msinada@quicinc.com
Move HE MCS mapper to a separate function and call new function
in ath11k_mac_copy_he_cap().
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00356-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1666128501-12364-4-git-send-email-quic_msinada@quicinc.com
In the previous behaviour only HE IE in management frames are changed
regarding MU-MIMO configurations and not in hardware. Adding push of
MU-MIMO configurations to the hardware as well.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00356-QCAHKSWPL_SILICONZ-1
Co-developed-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1666128501-12364-3-git-send-email-quic_msinada@quicinc.com
Including:
- Consolidate iommu_map/unmap functions. There have been
blocking and atomic variants so far, but that was problematic
as this approach does not scale with required new variants
which just differ in the GFP flags used.
So Jason consolidated this back into single functions that
take a GFP parameter. This has the potential to cause
conflicts with other trees, as they introduce new call-sites
for the changed functions. I offered them to pull in the
branch containing these changes and resolve it, but I am not
sure everyone did that. The conflicts this caused with
upstream up to v6.2-rc8 are resolved in the final merge
commit.
- Retire the detach_dev() call-back in iommu_ops
- Arm SMMU updates from Will:
- Device-tree binding updates:
* Cater for three power domains on SM6375
* Document existing compatible strings for Qualcomm SoCs
* Tighten up clocks description for platform-specific compatible strings
- Enable Qualcomm workarounds for some additional platforms that need them
- Intel VT-d updates from Lu Baolu:
- Add Intel IOMMU performance monitoring support
- Set No Execute Enable bit in PASID table entry
- Two performance optimizations
- Fix PASID directory pointer coherency
- Fix missed rollbacks in error path
- Cleanups
- Apple t8110 DART support
- Exynos IOMMU:
- Implement better fault handling
- Error handling fixes
- Renesas IPMMU:
- Add device tree bindings for r8a779g0
- AMD IOMMU:
- Various fixes for handling on SNP-enabled systems and
handling of faults with unknown request-ids
- Cleanups and other small fixes
- Various other smaller fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=ZaZV
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Consolidate iommu_map/unmap functions.
There have been blocking and atomic variants so far, but that was
problematic as this approach does not scale with required new
variants which just differ in the GFP flags used. So Jason
consolidated this back into single functions that take a GFP
parameter.
- Retire the detach_dev() call-back in iommu_ops
- Arm SMMU updates from Will:
- Device-tree binding updates:
- Cater for three power domains on SM6375
- Document existing compatible strings for Qualcomm SoCs
- Tighten up clocks description for platform-specific
compatible strings
- Enable Qualcomm workarounds for some additional platforms that
need them
- Intel VT-d updates from Lu Baolu:
- Add Intel IOMMU performance monitoring support
- Set No Execute Enable bit in PASID table entry
- Two performance optimizations
- Fix PASID directory pointer coherency
- Fix missed rollbacks in error path
- Cleanups
- Apple t8110 DART support
- Exynos IOMMU:
- Implement better fault handling
- Error handling fixes
- Renesas IPMMU:
- Add device tree bindings for r8a779g0
- AMD IOMMU:
- Various fixes for handling on SNP-enabled systems and
handling of faults with unknown request-ids
- Cleanups and other small fixes
- Various other smaller fixes and cleanups
* tag 'iommu-updates-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (71 commits)
iommu/amd: Skip attach device domain is same as new domain
iommu: Attach device group to old domain in error path
iommu/vt-d: Allow to use flush-queue when first level is default
iommu/vt-d: Fix PASID directory pointer coherency
iommu/vt-d: Avoid superfluous IOTLB tracking in lazy mode
iommu/vt-d: Fix error handling in sva enable/disable paths
iommu/amd: Improve page fault error reporting
iommu/amd: Do not identity map v2 capable device when snp is enabled
iommu: Fix error unwind in iommu_group_alloc()
iommu/of: mark an unused function as __maybe_unused
iommu: dart: DART_T8110_ERROR range should be 0 to 5
iommu/vt-d: Enable IOMMU perfmon support
iommu/vt-d: Add IOMMU perfmon overflow handler support
iommu/vt-d: Support cpumask for IOMMU perfmon
iommu/vt-d: Add IOMMU perfmon support
iommu/vt-d: Support Enhanced Command Interface
iommu/vt-d: Retrieve IOMMU perfmon capability information
iommu/vt-d: Support size of the register set in DRHD
iommu/vt-d: Set No Execute Enable bit in PASID table entry
iommu/vt-d: Remove sva from intel_svm_dev
...
When ath11k runs into internal errors upon suspend,
it returns an error code to pci_pm_suspend, which
aborts the entire system suspend.
The driver should not abort system suspend, but should
keep its internal errors to itself, and allow the system
to suspend. Otherwise, a user can suspend a laptop
by closing the lid and sealing it into a case, assuming
that is will suspend, rather than heating up and draining
the battery when in transit.
In practice, the ath11k device seems to have plenty of transient
errors, and subsequent suspend cycles after this failure
often succeed.
https://bugzilla.kernel.org/show_bug.cgi?id=216968
Fixes: d1b0c33850 ("ath11k: implement suspend for QCA6390 PCI devices")
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230201183201.14431-1-len.brown@intel.com
Fix sleep in atomic context warning detected by Smatch static checker
analyzer.
Following the locking pattern for peer_rhash_add lock tbl_mtx_lock mutex
always even if sta is not transitioning to another band.
This is peer_add function and a more secure locking should not cause
performance regression.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: d673cb6fe6 ("wifi: ath11k: fix peer addition/deletion error on sta band migration")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230209222622.1751-1-ansuelsmth@gmail.com
As of commit a1a2b7125e ("of/platform: Drop static setup of IRQ
resource from DT core"), we need to use platform_get_irq() instead of
platform_get_resource() to get our IRQs because
platform_get_resource() simply won't get them anymore.
This was already fixed in several other Atheros WiFi drivers,
apparently in response to Zeal Robot reports. An example of another
fix is commit 9503a1fc12 ("ath9k: Use platform_get_irq() to get the
interrupt"). ath11k seems to have been missed in this effort, though.
Without this change, WiFi wasn't coming up on my Qualcomm sc7280-based
hardware. Specifically, "platform_get_resource(pdev, IORESOURCE_IRQ,
i)" was failing even for i=0.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: a1a2b7125e ("of/platform: Drop static setup of IRQ resource from DT core")
Fixes: 00402f49d2 ("ath11k: Add support for WCN6750 device")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jun Yu <junyuu@chromium.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230201084131.v2.1.I69cf3d56c97098287fe3a70084ee515098390b70@changeid
ioremap() returns NULL pointer not PTR_ERR() when it fails,
so replace the IS_ERR() check with NULL pointer check.
Fixes: b42b3678c9 ("wifi: ath11k: remap ce register space for IPQ5018")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230217030031.4021289-1-yangyingliang@huawei.com
Set the WMI_SCAN_FLAG_EXT_PASSIVE_SCAN_START_TIME_ENHANCE flag
while sending the scan command. If this flag is enabled when the
incoming scan request comes with a strict start time and its duration
overlaps with next TBTT, then target adjust the start time accordingly
for passive scan. Target supporting this feature will advertise
WMI_TLV_SERVICE_PASSIVE_SCAN_START_TIME_ENHANCE.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221222131720.11368-1-quic_tamizhr@quicinc.com
ath.git patches for v6.3. Major changes:
ath12k
* new driver for Qualcomm Wi-Fi 7 devices
ath11k
* IPQ5018 support
* Fine Timing Measurement (FTM) responder role support
* channel 177 support
ath10k
* store WLAN firmware version in SMEM image table
The internal mechanisms support this, but instead of exposting the gfp to
the caller it wrappers it into iommu_map() and iommu_map_atomic()
Fix this instead of adding more variants for GFP_KERNEL_ACCOUNT.
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/1-v3-76b587fe28df+6e3-iommu_map_gfp_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Somehow an extra 'e' slipped in there without anyone noticing,
drop that from ieeee80211_obss_color_collision_notify().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
crypto_alloc_shash() allocates resources, which should be released by
crypto_free_shash(). When ath11k_peer_find() fails, there has memory
leak. Add missing crypto_free_shash() to fix this.
Fixes: 243874c64c ("ath11k: handle RX fragments")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230102081142.3937570-1-linmq006@gmail.com
Add support for the 5 GHz channel 177 with center frequency 5885 MHz and
operating class 125 per IEEE Std 802.11ax-2021, Table E-4.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220101912.30816-1-quic_wgong@quicinc.com
Fine Timing Measurement(FTM) support is used to measure round trip
time between two nodes.
Enable FTM responder feature using hw_params on supported device.
Since FTM functionality is offloaded to firmware, adding the
interface allows user space to enable or disable FTM responder.
Also add support for advertising the same in extended capabilities.
QCA6390, WCN6855 and WCN6750 do not support this feature.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220044435.10506-1-quic_rajkbhag@quicinc.com
ath11k fails to load if there are multiple ath11k PCI devices with same name:
ath11k_pci 0000:01:00.0: Hardware name qcn9074 hw1.0
debugfs: Directory 'ath11k' with parent '/' already present!
ath11k_pci 0000:01:00.0: failed to create ath11k debugfs
ath11k_pci 0000:01:00.0: failed to create soc core: -17
ath11k_pci 0000:01:00.0: failed to init core: -17
ath11k_pci: probe of 0000:01:00.0 failed with error -17
Fix this by creating a directory for each ath11k device using schema
<bus>-<devname>, for example "pci-0000:06:00.0". This directory created under
the top-level ath11k directory, for example /sys/kernel/debug/ath11k.
The reference to the toplevel ath11k directory is not stored anymore within ath11k, instead
it's retrieved using debugfs_lookup(). If the directory does not exist it will
be created. After the last directory from the ath11k directory is removed, for
example when doing rmmod ath11k, the empty ath11k directory is left in place,
it's a minor cosmetic issue anyway.
Here's an example hierarchy with one WCN6855:
ath11k
`-- pci-0000:06:00.0
|-- mac0
| |-- dfs_block_radar_events
| |-- dfs_simulate_radar
| |-- ext_rx_stats
| |-- ext_tx_stats
| |-- fw_dbglog_config
| |-- fw_stats
| | |-- beacon_stats
| | |-- pdev_stats
| | `-- vdev_stats
| |-- htt_stats
| |-- htt_stats_reset
| |-- htt_stats_type
| `-- pktlog_filter
|-- simulate_fw_crash
`-- soc_dp_stats
I didn't have a test setup where I could connect multiple ath11k devices to the
same the host, so I have only tested this with one device.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220121231.20120-1-kvalo@kernel.org
Following warning was observed
drivers/net/wireless/ath/ath11k/mac.c:2351:1: warning: the frame
size of 1184 bytes is larger than 1024 bytes [-Wframe-larger-than=]
A local variable is declared with a size larger than 1024 bytes
this causing a compilation warning. Change the local variable to
heap memory to fix the warning.
Tested-on: IPQ8074 AHB WLAN.HK.2.7.0.1-01701-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221205192125.13533-1-quic_kathirve@quicinc.com
ipq5018 is a ahb 2ghz device, enable the compatible support for
ipq5018 in ahb.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-9-quic_kathirve@quicinc.com
The Destination ring control register is different
for IPQ5018 when compared to IPQ8074/IPQ6018/QCN9074.
Hence create a new hw ops to fetch the hash ring map
for different device variants. ipq5018 hw ops
is similar to qcn9074 except for this change, so reuse
all the qcn9074 ops for ipq5018.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-8-quic_kathirve@quicinc.com
The ipq5018_ops is initialized for IPQ5018. This is different from
other platforms.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-7-quic_kathirve@quicinc.com
IPQ5018 hal srng register address & offsets are not
similar to IPQ8074/IPQ6018/QCN9074, hence define a
new set of srng register group data for IPQ5018.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-6-quic_kathirve@quicinc.com
In IPQ5018 ce register space is moved out of wcss unlike
ipq8074 or ipq6018 and the space is not contiguous,
hence remap the CE registers to a new space to access them.
Register read/write is modified to check if the register to be written
falls in the CE register space and corresponding register is written.
Also adjust the interrupt register address to ce irq enable/disable.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-5-quic_kathirve@quicinc.com
IPQ5018 is a single pdev device. Update host
and target CE configurations accordingly.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-4-quic_kathirve@quicinc.com
Add new compatible string for IPQ5018 and add
required hw params for IPQ5018. The hw descriptors size and
datapath ops are similar to QCN9074, hence reuse the same.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-3-quic_kathirve@quicinc.com
A crash happens when running the traffic with multiple clients:
Crash Signature : Unable to handle kernel paging request at
virtual address ffffffd700970918 During the crash, PC points to
"ieee80211_tx_rate_update+0x30/0x68 [mac80211]"
LR points to "ath11k_dp_htt_htc_t2h_msg_handler+0x5a8/0x8a0 [ath11k]".
Struct ppdu_stats_info is allocated and accessed from event callback via copy
engine tasklet, this has a problem when freeing it from ath11k_mac_op_stop().
Use data_lock during entire ath11k_dp_htt_get_ppdu_desc() call to protect
struct htt_ppdu_stats_info access and to avoid race condition when accessing it
from ath11k_mac_op_stop().
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Govindaraj Saminathan <quic_gsaminat@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221124071104.22506-1-quic_kathirve@quicinc.com
Second set of patches for v6.2. Only driver patches this time, nothing
really special. Unused platform data support was removed from wl1251
and rtw89 got WoWLAN support.
Major changes:
ath11k
* support configuring channel dwell time during scan
rtw89
* new dynamic header firmware format support
* Wake-over-WLAN support
rtl8xxxu
* enable IEEE80211_HW_SUPPORT_FAST_XMIT
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmN3ZagRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuk/Af+M9IXyWmis9behHlz2U+4PJ/+JF8VYIck
6Xup+FM0O1w6aHhAL8gNOhLl62jpYB0Exou0YizInGvwjjQk2Gtuq60KshkbN2zL
YK3sbcS66PyE19gfIQKJTW/s+9aBncRuvEb6HTZx5iF96mVFPeBDPduUGQksGs5/
Egf03eAqzdcIIcejKG1SUn2o0fLJ6jds0VftAas+chKI2Z5ADQWPzugvU0vlvXVE
oq3ws7Sg0yGcwOOttFwaXMBPrjmCty5uc/ELMhjvSLAsKULXymjZkrU1m5tanhGu
N1MDqviwCK7PJC/wQ2xo7YKNY/1LUc0xbwfbEXQITfbbPyjOz+ynQQ==
=wKQZ
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.2
Second set of patches for v6.2. Only driver patches this time, nothing
really special. Unused platform data support was removed from wl1251
and rtw89 got WoWLAN support.
Major changes:
ath11k
* support configuring channel dwell time during scan
rtw89
* new dynamic header firmware format support
* Wake-over-WLAN support
rtl8xxxu
* enable IEEE80211_HW_SUPPORT_FAST_XMIT
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently after the hardware restart triggered from the driver, the
station interface connection remains intact, since a disconnect trigger
is not sent to userspace. This can lead to a problem in targets where
the wifi mac sequence is added by the firmware.
After the target restart, its wifi mac sequence number gets reset to
zero. Hence AP to which our device is connected will receive frames with
a wifi mac sequence number jump to the past, thereby resulting in the
AP dropping all these frames, until the frame arrives with a wifi mac
sequence number which AP was expecting.
To avoid such frame drops, its better to trigger a station disconnect
upon target hardware restart which can be done with API
ieee80211_reconfig_disconnect exposed to mac80211.
The other targets are not affected by this change, since the hardware
params flag is not set.
Reported-by: kernel test robot <lkp@intel.com>
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221104085403.11025-1-quic_youghand@quicinc.com
Commit ff6d365898 ("soc: qcom: qmi: use const for struct
qmi_elem_info") allows QMI message encoding/decoding rules to be
const, so do that for ath11k.
Compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220915002303.12206-1-quic_jjohnson@quicinc.com
(cherry picked from commit d99884ad9e in ath-next
as users are seeing this bug more now, also cc stable)
Running this test in a loop it is easy to reproduce an rtnl deadlock:
iw reg set FI
ifconfig wlan0 down
What happens is that thread A (workqueue) tries to update the regulatory:
try to acquire the rtnl_lock of ar->regd_update_work
rtnl_lock+0x17/0x20
ath11k_regd_update+0x15a/0x260 [ath11k]
ath11k_regd_update_work+0x15/0x20 [ath11k]
process_one_work+0x228/0x670
worker_thread+0x4d/0x440
kthread+0x16d/0x1b0
ret_from_fork+0x22/0x30
And thread B (ifconfig) tries to stop the interface:
try to cancel_work_sync(&ar->regd_update_work) in ath11k_mac_op_stop().
ifconfig 3109 [003] 2414.232506: probe:
ath11k_mac_op_stop: (ffffffffc14187a0)
drv_stop+0x30 ([mac80211])
ieee80211_do_stop+0x5d2 ([mac80211])
ieee80211_stop+0x3e ([mac80211])
__dev_close_many+0x9e ([kernel.kallsyms])
__dev_change_flags+0xbe ([kernel.kallsyms])
dev_change_flags+0x23 ([kernel.kallsyms])
devinet_ioctl+0x5e3 ([kernel.kallsyms])
inet_ioctl+0x197 ([kernel.kallsyms])
sock_do_ioctl+0x4d ([kernel.kallsyms])
sock_ioctl+0x264 ([kernel.kallsyms])
__x64_sys_ioctl+0x92 ([kernel.kallsyms])
do_syscall_64+0x3a ([kernel.kallsyms])
entry_SYSCALL_64_after_hwframe+0x63 ([kernel.kallsyms])
__GI___ioctl+0x7 (/lib/x86_64-linux-gnu/libc-2.23.so)
The sequence of deadlock is:
1. Thread B calls rtnl_lock().
2. Thread A starts to run and calls rtnl_lock() from within
ath11k_regd_update_work(), then enters wait state because the lock is owned by
thread B.
3. Thread B continues to run and tries to call
cancel_work_sync(&ar->regd_update_work), but thread A is in
ath11k_regd_update_work() waiting for rtnl_lock(). So cancel_work_sync()
forever waits for ath11k_regd_update_work() to finish and we have a deadlock.
Fix this by switching from using regulatory_set_wiphy_regd_sync() to
regulatory_set_wiphy_regd(). Now cfg80211 will schedule another workqueue which
handles the locking on it's own. So the ath11k workqueue can simply exit without
taking any locks, avoiding the deadlock.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Cc: <stable@vger.kernel.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
[kvalo: improve commit log]
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
The 2.7.0 series of QCN9074's firmware requests 5 segments
of memory instead of 3 (as in the 2.5.0 series).
The first segment (11M) is too large to be kalloc'd in one
go on x86 and requires piecemeal 1MB allocations, as was
the case with the prior public firmware (2.5.0, 15M).
Since f6f92968e1, ath11k will break the memory requests,
but only if there were fewer than 3 segments requested by
the firmware. It seems that 5 segments works fine and
allows QCN9074 to boot on x86 with firmware 2.7.0, so
change things accordingly.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
Signed-off-by: Tyler J. Stachecki <stachecki.tyler@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221022042728.43015-1-stachecki.tyler@gmail.com
ath11k_mac_he_gi_to_nl80211_he_gi() generates a valid warning with gcc-13:
drivers/net/wireless/ath/ath11k/mac.c:321:20: error: conflicting types for 'ath11k_mac_he_gi_to_nl80211_he_gi' due to enum/integer mismatch; have 'enum nl80211_he_gi(u8)'
drivers/net/wireless/ath/ath11k/mac.h:166:5: note: previous declaration of 'ath11k_mac_he_gi_to_nl80211_he_gi' with type 'u32(u8)'
I.e. the type of the return value ath11k_mac_he_gi_to_nl80211_he_gi() in
the declaration is u32, while the definition spells enum nl80211_he_gi.
Synchronize them to the latter.
Cc: Martin Liska <mliska@suse.cz>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: ath11k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221031114341.10377-1-jirislaby@kernel.org
qmi_msg_handler is required to be null terminated by QMI module.
There might be a case where a handler for a msg id is not present in the
handlers array which can lead to infinite loop while searching the handler
and therefore out of bound access in qmi_invoke_handler().
Hence update the initialization in qmi_msg_handler data structure.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rahul Bhattacharjee <quic_rbhattac@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221021090126.28626-1-quic_rbhattac@quicinc.com
First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7.
All mac80211 driver are now converted to use internal TX queues, this
might cause some regressions so we wanted to do this early in the
cycle.
Note: wireless tree was merged[1] to wireless-next to avoid some
conflicts with mac80211 patches between the trees. Unfortunately there
are still two smaller conflicts in net/mac80211/util.c which Stephen
also reported[2]. In the first conflict initialise scratch_len to
"params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and
in the second conflict take the version which uses elems->scratch_pos.
Git diff output should like this:
--- a/net/mac80211/util.c
+++ b/net/mac80211/util.c
@@@ -1506,7 -1648,7 +1650,7 @@@ ieee802_11_parse_elems_full(struct ieee
const struct element *non_inherit = NULL;
u8 *nontransmitted_profile;
int nontransmitted_profile_len = 0;
- size_t scratch_len = params->len;
- size_t scratch_len = params->scratch_len ?: 2 * params->len;
++ size_t scratch_len = params->scratch_len ?: 3 * params->len;
elems = kzalloc(sizeof(*elems) + scratch_len, GFP_ATOMIC);
if (!elems)
[1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91
[2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/
Major changes:
mac80211
* preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues
* add API to show the link STAs in debugfs
* all mac80211 drivers are now using mac80211 internal TX queues (iTXQs)
rtw89
* support 8852BE
rtl8xxxu
* support RTL8188FU
brmfmac
* support two station interfaces concurrently
bcma
* support SPROM rev 11
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmNb2KwRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZs6hggAqrmgHaiRbPYlLVE0hFVaGeVXslfpK9nj
ZGr3bwG5FpioxjAsI7NfwEwpq+FoxTUigG/SShw1Rr8lw43Nt7E57+5McK3qWdKC
5/WndfChPppjtJUpc6PN+UcmCuhcm4TAyMAojbTe5lJ9cJ4yyOWZChDwah3BVZQk
/tHK4qKq8gpppwgkiJ88VdTVoVv5anIvXHH3lAIteljxk0zkaEM7lIQhIFst/zpX
cu/cWvKz2Rh6vnYjkzl8BcrbW8e0/VwnzWggtWs4/kIuRVnHRrrGwlnsULShOscM
fmK+RI2CbJIMucttUOHOXjCg4wwppSit1rH4xOkcwlvrFa7AvDbdHg==
=Zils
-----END PGP SIGNATURE-----
Kalle Valo says:
====================
pull-request: wireless-next-2022-10-28
First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7.
All mac80211 driver are now converted to use internal TX queues, this
might cause some regressions so we wanted to do this early in the
cycle.
Note: wireless tree was merged[1] to wireless-next to avoid some
conflicts with mac80211 patches between the trees. Unfortunately there
are still two smaller conflicts in net/mac80211/util.c which Stephen
also reported[2]. In the first conflict initialise scratch_len to
"params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and
in the second conflict take the version which uses elems->scratch_pos.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91
[2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/
mac80211
- preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues
- add API to show the link STAs in debugfs
- all mac80211 drivers are now using mac80211 internal TX queues (iTXQs)
rtw89
- support 8852BE
rtl8xxxu
- support RTL8188FU
brmfmac
- support two station interfaces concurrently
bcma
- support SPROM rev 11
====================
Link: https://lore.kernel.org/r/20221028132943.304ECC433B5@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During firmware recovery, the monitor interface is not
getting created in the driver and firmware since
the respective flags are not updated properly.
So after firmware recovery is successful, when monitor
interface is brought down manually, firmware assertion
is observed, since we are trying to bring down the
interface which is not yet created in the firmware.
Fix this by updating the monitor flags properly per
phy#, during firmware recovery.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221014155054.11471-1-quic_nmaran@quicinc.com
Current code does not wait for vdev delete completion on vdev create
failures and tries to send another vdev create followed by vdev set
param to firmware with same vdev id. This causes firmware crash.
Fix this crash by waiting for vdev delete completion on vdev
create failures.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.6.0.1-00905-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221011095346.3901-1-quic_ssreeela@quicinc.com
We are seeing system stuck on some specific platforms due to
WLAN chip fails to wakeup from D3cold state.
With this flag, firmware will send PME message during wakeup
and this issue is gone.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221010033237.415478-1-quic_bqiang@quicinc.com
Add support to configure channel dwell time during scan.
Dwell time help to stay on the channel for a specified duration
during scan and aid userspace in finding WiFi networks. Very
useful in passive scans where longer dwell times are needed
to find the WiFi networks.
Configure channel dwell time from duration of the scan request
received from mac80211 when the duration is non-zero. When the
scan request does not have duration value, use the default ones,
the current implementation.
Advertise corresponding feature flag NL80211_EXT_FEATURE_SET_SCAN_DWELL
to enable the feature.
Change is applicable for all ath11k hardware.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221007051130.6067-1-quic_mpubbise@quicinc.com
In the VIF (other than monitor type) creation request, we should not
throw the error code when the monitor VIF creation fails, since the
actual VIF creation succeeds. If we throw the error code from driver
then the actual VIF creation get fail. So suppress the monitor VIF
creation error by throwing warning message instead of error code.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00760-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221006005842.8599-1-quic_periyasa@quicinc.com
Currently, ath11k sends peer assoc command for each peer to
firmware when bandwidth changes. Peer assoc command is a
bulky command and if many clients are connected, this could
lead to firmware buffer getting overflowed leading to a firmware
assert.
However, during bandwidth change, only phymode and bandwidth
also can be updated by WMI set peer param command. This makes
the overall command light when compared to peer assoc and for
multi-client cases, firmware buffer overflow also does not
occur.
Remove sending peer assoc command during sta bandwidth change
and instead add sending WMI set peer param command for phymode
and bandwidth.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: f187fe8e3b ("ath11k: fix firmware crash during channel switch")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221005095430.19890-1-quic_adisi@quicinc.com
Linaro reported stringop-overread warnings in ath11k (this is one of many):
drivers/net/wireless/ath/ath11k/mac.c:2238:29: error: 'ath11k_peer_assoc_h_he_limit' reading 16 bytes from a region of size 0 [-Werror=stringop-overread]
My further investigation showed that these warnings happen on GCC 11.3 but not
with GCC 12.2, and with only the kernel config Linaro provided:
https://builds.tuxbuild.com/2F4W7nZHNx3T88RB0gaCZ9hBX6c/config
I saw the same warnings both with arm64 and x86_64 builds and KASAN seems to be
the reason triggering these warnings with GCC 11. Nobody else has reported
this so this seems to be quite rare corner case. I don't know what specific
commit started emitting this warning so I can't provide a Fixes tag. The
function hasn't been touched for a year.
I decided to workaround this by converting the pointer to a new array in stack,
and then copying the data to the new array. It's only 16 bytes anyway and this
is executed during association, so not in a hotpath.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Link: https://lore.kernel.org/all/CA+G9fYsZ_qypa=jHY_dJ=tqX4515+qrV9n2SWXVDHve826nF7Q@mail.gmail.com/
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221010160638.20152-1-kvalo@kernel.org
Running this test in a loop it is easy to reproduce an rtnl deadlock:
iw reg set FI
ifconfig wlan0 down
What happens is that thread A (workqueue) tries to update the regulatory:
try to acquire the rtnl_lock of ar->regd_update_work
rtnl_lock+0x17/0x20
ath11k_regd_update+0x15a/0x260 [ath11k]
ath11k_regd_update_work+0x15/0x20 [ath11k]
process_one_work+0x228/0x670
worker_thread+0x4d/0x440
kthread+0x16d/0x1b0
ret_from_fork+0x22/0x30
And thread B (ifconfig) tries to stop the interface:
try to cancel_work_sync(&ar->regd_update_work) in ath11k_mac_op_stop().
ifconfig 3109 [003] 2414.232506: probe:
ath11k_mac_op_stop: (ffffffffc14187a0)
drv_stop+0x30 ([mac80211])
ieee80211_do_stop+0x5d2 ([mac80211])
ieee80211_stop+0x3e ([mac80211])
__dev_close_many+0x9e ([kernel.kallsyms])
__dev_change_flags+0xbe ([kernel.kallsyms])
dev_change_flags+0x23 ([kernel.kallsyms])
devinet_ioctl+0x5e3 ([kernel.kallsyms])
inet_ioctl+0x197 ([kernel.kallsyms])
sock_do_ioctl+0x4d ([kernel.kallsyms])
sock_ioctl+0x264 ([kernel.kallsyms])
__x64_sys_ioctl+0x92 ([kernel.kallsyms])
do_syscall_64+0x3a ([kernel.kallsyms])
entry_SYSCALL_64_after_hwframe+0x63 ([kernel.kallsyms])
__GI___ioctl+0x7 (/lib/x86_64-linux-gnu/libc-2.23.so)
The sequence of deadlock is:
1. Thread B calls rtnl_lock().
2. Thread A starts to run and calls rtnl_lock() from within
ath11k_regd_update_work(), then enters wait state because the lock is owned by
thread B.
3. Thread B continues to run and tries to call
cancel_work_sync(&ar->regd_update_work), but thread A is in
ath11k_regd_update_work() waiting for rtnl_lock(). So cancel_work_sync()
forever waits for ath11k_regd_update_work() to finish and we have a deadlock.
Fix this by switching from using regulatory_set_wiphy_regd_sync() to
regulatory_set_wiphy_regd(). Now cfg80211 will schedule another workqueue which
handles the locking on it's own. So the ath11k workqueue can simply exit without
taking any locks, avoiding the deadlock.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
[kvalo: improve commit log]
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221006151747.13757-1-kvalo@kernel.org
mac80211 is fully switching over to the internal TX queue (iTXQ)
implementation. Update all drivers not yet providing the now mandatory
wake_tx_queue() callback.
As an side effect the netdev interfaces of all updated drivers will
switch to the noqueue qdisc.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[add staging drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
* refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
* support CYW43439 SDIO chipset
* support BCM4378 on Apple platforms
* support CYW89459 PCIe chipset
rtw89
* more work to get rtw8852c supported
* P2P support
* support for enabling and disabling MSDU aggregation via nl80211
mt76
* tx status reporting improvements
ath11k
* cold boot calibration support on WCN6750
* Target Wake Time (TWT) debugfs support for STA interface
* support to connect to a non-transmit MBSSID AP profile
* enable remain-on-channel support on WCN6750
* implement SRAM dump debugfs interface
* enable threaded NAPI on all hardware
* WoW support for WCN6750
* support to provide transmit power from firmware via nl80211
* support to get power save duration for each client
* spectral scan support for 160 MHz
wcn36xx
* add SNR from a received frame as a source of system entropy
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmM3BGYRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuR3Af/XiuMlnDB6flq+M/kQHLWWvHybLw5aCJ7
l3yXhNFWxpBl2hQXtj17JSjVCYQmxbfrgRqhbNhyACO25bpymCb5QctB9X+Y7TwL
250JmuKvQfFx5oJNRfJ67dKTf3raloQYbdEMJNqySgebL+eSfrDskc9vaCLVDmCK
I994fl0Q1wUbJ6fbuIFd07ti8ay6UlSS/iakv4+nEeimabtZWJWlXBWYRpKpikdP
h9z2kPtss6yz6seaQuw6ny+qysYLi11Tp+Cued9XR3dWOOhB2X1tLHH0H02xPw76
9OJZEJHycP2juxjMfAaktHY+VX36GPLsMLUTVusH0h/Fdy3VG8YSAw==
=emmG
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.1
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
- refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
- support CYW43439 SDIO chipset
- support BCM4378 on Apple platforms
- support CYW89459 PCIe chipset
rtw89
- more work to get rtw8852c supported
- P2P support
- support for enabling and disabling MSDU aggregation via nl80211
mt76
- tx status reporting improvements
ath11k
- cold boot calibration support on WCN6750
- Target Wake Time (TWT) debugfs support for STA interface
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- implement SRAM dump debugfs interface
- enable threaded NAPI on all hardware
- WoW support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
wcn36xx
- add SNR from a received frame as a source of system entropy
* tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (231 commits)
wifi: rtl8xxxu: Improve rtl8xxxu_queue_select
wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
wifi: rtl8xxxu: gen2: Enable 40 MHz channel width
wifi: rtw89: 8852b: configure DLE mem
wifi: rtw89: check DLE FIFO size with reserved size
wifi: rtw89: mac: correct register of report IMR
wifi: rtw89: pci: set power cut closed for 8852be
wifi: rtw89: pci: add to do PCI auto calibration
wifi: rtw89: 8852b: implement chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add DMA busy checking bits to chip info
wifi: rtw89: mac: define DMA channel mask to avoid unsupported channels
wifi: rtw89: pci: mask out unsupported TX channels
iwlegacy: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper
ipw2x00: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
wifi: iwlwifi: Track scan_cmd allocation size explicitly
brcmfmac: Remove the call to "dtim_assoc" IOVAR
brcmfmac: increase dcmd maximum buffer size
brcmfmac: Support 89459 pcie
brcmfmac: increase default max WOWL patterns to 16
cw1200: fix incorrect check to determine if no element is found in list
...
====================
Link: https://lore.kernel.org/r/20220930150413.A7984C433D6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 26f3a021b3 ("ath11k: allocate smaller chunks of memory for
firmware") and commit f6f92968e1 ("ath11k: qmi: try to allocate a
big block of DMA memory first") change ath11k to allocate the memory
chunks for target twice while wlan load. It fails for the 1st time
because of large memory and then changed to allocate many small chunks
for the 2nd time sometimes as below log.
1st time failed:
[10411.640620] ath11k_pci 0000:05:00.0: qmi firmware request memory request
[10411.640625] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 6881280
[10411.640630] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 3784704
[10411.640658] ath11k_pci 0000:05:00.0: qmi dma allocation failed (6881280 B type 1), will try later with small size
[10411.640671] ath11k_pci 0000:05:00.0: qmi delays mem_request 2
[10411.640677] ath11k_pci 0000:05:00.0: qmi respond memory request delayed 1
2nd time success:
[10411.642004] ath11k_pci 0000:05:00.0: qmi firmware request memory request
[10411.642008] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642012] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642014] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642016] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642018] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642020] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642022] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642024] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642027] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642029] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
[10411.642031] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 458752
[10411.642033] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 131072
[10411.642035] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642037] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642039] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642041] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642043] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642045] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 524288
[10411.642047] ath11k_pci 0000:05:00.0: qmi mem seg type 4 size 491520
[10411.642049] ath11k_pci 0000:05:00.0: qmi mem seg type 1 size 524288
And then commit 5962f370ce ("ath11k: Reuse the available memory after
firmware reload") skip the ath11k_qmi_free_resource() which frees the
memory chunks while recovery, after that, when run recovery test on
WCN6855, a warning happened every time as below and finally leads fail
for recovery.
[ 159.570318] BUG: Bad page state in process kworker/u16:5 pfn:33300
[ 159.570320] page:0000000096ffdbb9 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x33300
[ 159.570324] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
[ 159.570329] raw: 000fffffc0000000 0000000000000000 dead000000000122 0000000000000000
[ 159.570332] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 159.570334] page dumped because: nonzero _refcount
[ 159.570440] firewire_ohci syscopyarea sysfillrect psmouse sdhci_pci ahci sysimgblt firewire_core fb_sys_fops libahci crc_itu_t cqhci drm sdhci e1000e wmi video
[ 159.570460] CPU: 2 PID: 217 Comm: kworker/u16:5 Kdump: loaded Tainted: G B 5.19.0-rc1-wt-ath+ #3
[ 159.570465] Hardware name: LENOVO 418065C/418065C, BIOS 83ET63WW (1.33 ) 07/29/2011
[ 159.570467] Workqueue: qmi_msg_handler qmi_data_ready_work [qmi_helpers]
[ 159.570475] Call Trace:
[ 159.570476] <TASK>
[ 159.570478] dump_stack_lvl+0x49/0x5f
[ 159.570486] dump_stack+0x10/0x12
[ 159.570493] bad_page+0xab/0xf0
[ 159.570502] check_free_page_bad+0x66/0x70
[ 159.570511] __free_pages_ok+0x530/0x9a0
[ 159.570517] ? __dev_printk+0x58/0x6b
[ 159.570525] ? _dev_printk+0x56/0x72
[ 159.570534] ? qmi_decode+0x119/0x470 [qmi_helpers]
[ 159.570543] __free_pages+0x91/0xd0
[ 159.570548] dma_free_contiguous+0x50/0x60
[ 159.570556] dma_direct_free+0xe5/0x140
[ 159.570564] dma_free_attrs+0x35/0x50
[ 159.570570] ath11k_qmi_msg_mem_request_cb+0x2ae/0x3c0 [ath11k]
[ 159.570620] qmi_invoke_handler+0xac/0xe0 [qmi_helpers]
[ 159.570630] qmi_handle_message+0x6d/0x180 [qmi_helpers]
[ 159.570643] qmi_data_ready_work+0x2ca/0x440 [qmi_helpers]
[ 159.570656] process_one_work+0x227/0x440
[ 159.570667] worker_thread+0x31/0x3d0
[ 159.570676] ? process_one_work+0x440/0x440
[ 159.570685] kthread+0xfe/0x130
[ 159.570692] ? kthread_complete_and_exit+0x20/0x20
[ 159.570701] ret_from_fork+0x22/0x30
[ 159.570712] </TASK>
The reason is because when wlan start to recovery, the type, size and
count is not same for the 1st and 2nd QMI_WLFW_REQUEST_MEM_IND message,
Then it leads the parameter size is not correct for the dma_free_coherent().
For the chunk[1], the actual dma size is 524288 which allocate in the
2nd time of the initial wlan load phase, and the size which pass to
dma_free_coherent() is 3784704 which is got in the 1st time of recovery
phase, then warning above happened.
Change to use prev_size of struct target_mem_chunk for the paramter of
dma_free_coherent() since prev_size is the real size of last load/recovery.
Also change to check both type and size of struct target_mem_chunk to
reuse the memory to avoid mismatch buffer size for target. Then the
warning disappear and recovery success. When the 1st QMI_WLFW_REQUEST_MEM_IND
for recovery arrived, the trunk[0] is freed in ath11k_qmi_alloc_target_mem_chunk()
and then dma_alloc_coherent() failed caused by large size, and then
trunk[1] is freed in ath11k_qmi_free_target_mem_chunk(), the left 18
trunks will be reuse for the 2nd QMI_WLFW_REQUEST_MEM_IND message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 5962f370ce ("ath11k: Reuse the available memory after firmware reload")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220928073832.16251-1-quic_wgong@quicinc.com
Currently, ath11k_pcic_read() returns an error if wakeup()
fails, this makes firmware crash debug quite hard because we can
get nothing.
Change to go ahead on wakeup failure, in that case we still may
get something valid to check. There should be no mislead due
to incorrect content because we are aware of the failure with the
log printed.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220928015140.5431-1-quic_bqiang@quicinc.com
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, recovery flag is set immediately upon firmware
exit but tx queues are stopped once firmware arrives back
and is ready which is during ath11k_core_restart. Once
ieee80211 hw restart is completed, tx queues are resumed.
If during the time delta between firmware exit and firmware
ready, mac80211 send packets, currently ath11k will drop it
since recovery flag will be set. But warning prints will
come -
"ath11k c000000.wifi: failed to transmit frame -108"
If more tx packets are there, this could lead to flooding
of above print.
However, actually tx queues should be stopped immediately
when firmware leaves. This will prevent packets to get
dropped when firmware is recovering.
Add fix to stop tx queues immediately after firmware exit.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220923170235.18873-1-quic_adisi@quicinc.com
ath.git patches for v6.1. Major changes:
ath11k
* cold boot calibration support on WCN6750
* Target Wake Time (TWT) debugfs support for STA interface
* support to connect to a non-transmit MBSSID AP profile
* enable remain-on-channel support on WCN6750
* implement SRAM dump debugfs interface
* enable threaded NAPI on all hardware
* WoW support for WCN6750
* support to provide transmit power from firmware via nl80211
* support to get power save duration for each client
* spectral scan support for 160 MHz
wcn36xx
* add SNR from a received frame as a source of system entropy
We are seeing system hangs during WoWLAN suspend, and get below
two stacks:
Stack1:
[ffffb02cc1557b20] __schedule at ffffffff8bb10860
[ffffb02cc1557ba8] schedule at ffffffff8bb10f24
[ffffb02cc1557bb8] schedule_timeout at ffffffff8bb16d88
[ffffb02cc1557c30] wait_for_completion at ffffffff8bb11778
[ffffb02cc1557c78] __flush_work at ffffffff8b0b30cd
[ffffb02cc1557cf0] __cancel_work_timer at ffffffff8b0b33ad
[ffffb02cc1557d60] ath11k_mac_drain_tx at ffffffffc0c1f0ca [ath11k]
[ffffb02cc1557d70] ath11k_wow_op_suspend at ffffffffc0c5201e [ath11k]
[ffffb02cc1557da8] __ieee80211_suspend at ffffffffc11e2bd3 [mac80211]
[ffffb02cc1557dd8] wiphy_suspend at ffffffffc0f901ac [cfg80211]
[ffffb02cc1557e08] dpm_run_callback at ffffffff8b75118a
[ffffb02cc1557e38] __device_suspend at ffffffff8b751630
[ffffb02cc1557e70] async_suspend at ffffffff8b7519ea
[ffffb02cc1557e88] async_run_entry_fn at ffffffff8b0bf4ce
[ffffb02cc1557ea8] process_one_work at ffffffff8b0b1a24
[ffffb02cc1557ee0] worker_thread at ffffffff8b0b1c4a
[ffffb02cc1557f18] kthread at ffffffff8b0b9cb8
[ffffb02cc1557f50] ret_from_fork at ffffffff8b001d32
Stack2:
[ffffb02cc00b7d18] __schedule at ffffffff8bb10860
[ffffb02cc00b7da0] schedule at ffffffff8bb10f24
[ffffb02cc00b7db0] schedule_preempt_disabled at ffffffff8bb112b4
[ffffb02cc00b7db8] __mutex_lock at ffffffff8bb127ea
[ffffb02cc00b7e38] ath11k_mgmt_over_wmi_tx_work at ffffffffc0c1aa44 [ath11k]
[ffffb02cc00b7ea8] process_one_work at ffffffff8b0b1a24
[ffffb02cc00b7ee0] worker_thread at ffffffff8b0b1c4a
[ffffb02cc00b7f18] kthread at ffffffff8b0b9cb8
[ffffb02cc00b7f50] ret_from_fork at ffffffff8b001d32
From the first stack, ath11k_mac_drain_tx calls
cancel_work_sync(&ar->wmi_mgmt_tx_work) and waits all packets to be sent
out or dropped. However, we find from Stack2 that this work item is blocked
because ar->conf_mutex is already held by ath11k_wow_op_suspend.
Fix this issue by moving ath11k_mac_wait_tx_complete to the start of
ath11k_wow_op_suspend where ar->conf_mutex has not been acquired. And
this change also makes the logic in ath11k_wow_op_suspend match the
logic in ath11k_mac_op_start and ath11k_mac_op_stop.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220919021435.2459-1-quic_bqiang@quicinc.com
ath11k_mac_drain_tx is already called in ath11k_mac_wait_tx_complete, no need to call it again. So remove it.
This is found in code review.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220919020259.1746-1-quic_bqiang@quicinc.com
There are two types of 160 MHz spectral scan support mentioned below
1. Fragmented approach
2. Single event approach
In this fragmented approach, single 160 MHz will be split as two
80 MHz buffer. First fft sample buffer will contain spectral scan
result of primary 80 MHz and the second fft sample buffer will contain
secondary 80 MHz and here cfreq1 and cfreq2 will be mentioned.
In case of 160 MHz on 36th channel will contain cfreq1 as 5210 and
cfreq2 as 5290. Chipsets which support this approach are IPQ8074/IPQ6018.
Replacing freq1 with freq2 in every secondary sepctral scan event to
distinguish between two different 80 MHz spectral event data.
In the 2nd approach each fft sample buffer will contain spectral scan
result for whole 160 MHz by mentioning cfreq1 as 5250 which is center
frequency of whole 160 MHz. Chipset which support this approach is QCN9074.
Host will receive spectral event from target for every 5 fft samples.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01120-QCAHKSWPL-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01120-QCAHKSWP
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725055001.15194-1-quic_tamizhr@quicinc.com
Add support to get the following power save information through debugfs interface,
* Current ps state of the peer
* Time duration since the peer is in power save
* Total duration of the peer spent in power save
Above information is helpful in debugging the issues with power save clients.
This patch also add trace log support for PS timekeeper to track the PS state
change of the peers alongs with the peer MAC address and timestamp.
Use the below commands to get the above power save information,
To know the time_since_station_in_power_save:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/current_ps_duration
To know power_save_duration:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/total_ps_duration
To reset the power_save_duration of all stations connected to AP:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath11k/reset_ps_duration
To enable/disable the ps_timekeeper:
echo Y > /sys/kernel/debug/ieee80211/phyX/ath11k/ps_timekeeper_enable
Y = 1 to enable and Y = 0 to disable.
To record PS timekeeer logs after enabling ps_timekeeper:
trace-cmd record -e ath11k_ps_timekeeper
Tested-on: Tested-on: IPQ8074 WLAN.HK.2.5.0.1-00991-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725054601.14719-1-quic_tamizhr@quicinc.com
This patch try to fix the following error.
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561227] ath11k c000000.wifi: peer already added vdev id 0 req, vdev id 1 present
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561282] ath11k c000000.wifi: Failed to add peer: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.568053] ath11k c000000.wifi: Failed to add station: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: Could not add STA to kernel driver
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: did not acknowledge authentication response
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan1: AP-STA-DISCONNECTED 28:c2:1f:xx:xx:xx
Wed Jun 1 22:19:31 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: disassociated due to inactivity
Wed Jun 1 22:19:32 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
To repro this:
- Have 2 Wifi with the same bssid and pass on different band (2.4 and
5GHz)
- Enable 802.11r Fast Transaction with same mobility domain
- FT Protocol: FT over the Air
From a openwrt system issue the command (with the correct mac)
ubus call hostapd.wlan1 wnm_disassoc_imminent '{"addr":"28:C2:1F:xx:xx:xx"}'
Notice the log printing the errors.
The cause of this error has been investigated and we found that this is
related to the WiFi Fast Transaction feature. We observed that this is
triggered when the router tells the device to change band. In this case
the device first auth to the other band and then the disconnect path
from the prev band is triggered.
This is problematic with the current rhash implementation since the
addrs is used as key and the logic of "adding first, delete later"
conflicts with the rhash logic.
In fact peer addition will fail since the peer is already added and with
that fixed a peer deletion will cause unitended effect by removing the
peer just added.
Current solution to this is to add additional logic to the peer delete,
make sure we are deleting the correct peer taken from the rhash
table (and fallback to the peer list) and for the peer add logic delete
the peer entry for the rhash list before adding the new one (counting as
an error only when a peer with the same vlan_id is asked to be added).
With this change, a sta can correctly transition from 2.4GHz and 5GHZ
with no drop and no error are printed.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: 7b0c70d92a ("ath11k: Add peer rhash table support")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603164559.27769-1-ansuelsmth@gmail.com
The number of spatial streams used when acting as a beamformee in VHT
mode are reported by the firmware as 7 (8 sts - 1) both in IPQ6018 and
IPQ8074 which respectively have 2 and 4 sts each. So the firmware should
report 1 (2 - 1) and 3 (4 - 1).
Fix this by checking that the number of VHT beamformee sts reported by
the firmware is not greater than the number of receiving antennas - 1.
The fix is based on the same approach used in this same function for
sanitizing the number of sounding dimensions reported by the firmware.
Without this change, acting as a beamformee in VHT mode is not working
properly.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220616173947.21901-1-jesus.manzano@galgus.net
Devices may provide their own MAC address via system firmware (e.g.,
device tree), especially in the case where the device doesn't have a
useful EEPROM on which to store its MAC address (e.g., for integrated
ahb WCN6750).
Use the generic device helper to retrieve the MAC address, and (if
present) honor it above the MAC address advertised by the card.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Jun Yu <junyuu@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220920003117.841442-1-junyuu@chromium.org
Driver does not support get_txpower mac ops because of which
cfg80211 returns vif->bss_conf.txpower to user space. bss_conf.txpower
gets its value from ieee80211_channel->max_reg_power. However, the final
txpower is dependent on few other parameters apart from max regulatory
supported power. It is the firmware which knows about all these
parameters and considers the minimum for each packet transmission.
All ath11k firmware reports the final tx power in firmware pdev stats
which falls under fw_stats.
Add get_txpower mac ops to get the tx power from firmware leveraging
fw_stats and return it accordingly.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603082814.31466-3-quic_adisi@quicinc.com
Currently, firmware stats, comprising pdev, vdev and beacon stats are
part of debugfs. In firmware pdev stats, firmware reports the final
Tx power used to transmit each packet. If driver wants to know the
final Tx power being used at firmware level, it can leverage from
firmware pdev stats.
Move firmware stats out of debugfs context in order to leverage
the final Tx power reported in it even when debugfs is disabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603082814.31466-2-quic_adisi@quicinc.com
It has a fail log which is ath11k_dbg in ath11k_dp_rx_process_mon_status(),
as below, it will not print when debug_mask is not set ATH11K_DBG_DATA.
ath11k_dbg(ab, ATH11K_DBG_DATA,
"failed to find the peer with peer_id %d\n",
ppdu_info.peer_id);
When run scan with station disconnected, the peer_id is 0 for case
HAL_RX_MPDU_START in ath11k_hal_rx_parse_mon_status_tlv() which called
from ath11k_dp_rx_process_mon_status(), and the peer_id of ppdu_info is
reset to 0 in the while loop, so it does not match condition of the
check "if (ppdu_info->peer_id == HAL_INVALID_PEERID" in the loop, and
then the log "failed to find the peer with peer_id 0" print after the
check in the loop, it is below call stack when debug_mask is set
ATH11K_DBG_DATA.
The reason is this commit 01d2f285e3 ("ath11k: decode HE status tlv")
add "memset(ppdu_info, 0, sizeof(struct hal_rx_mon_ppdu_info))" in
ath11k_dp_rx_process_mon_status(), but the commit does not initialize
the peer_id to HAL_INVALID_PEERID, then lead the check mis-match.
Callstack of the failed log:
[12335.689072] RIP: 0010:ath11k_dp_rx_process_mon_status+0x9ea/0x1020 [ath11k]
[12335.689157] Code: 89 ff e8 f9 10 00 00 be 01 00 00 00 4c 89 f7 e8 dc 4b 4e de 48 8b 85 38 ff ff ff c7 80 e4 07 00 00 01 00 00 00 e9 20 f8 ff ff <0f> 0b 41 0f b7 96 be 06 00 00 48 c7 c6 b8 50 44 c1 4c 89 ff e8 fd
[12335.689180] RSP: 0018:ffffb874001a4ca0 EFLAGS: 00010246
[12335.689210] RAX: 0000000000000000 RBX: ffff995642cbd100 RCX: 0000000000000000
[12335.689229] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff99564212cd18
[12335.689248] RBP: ffffb874001a4dc0 R08: 0000000000000001 R09: 0000000000000000
[12335.689268] R10: 0000000000000220 R11: ffffb874001a48e8 R12: ffff995642473d40
[12335.689286] R13: ffff99564212c5b8 R14: ffff9956424736a0 R15: ffff995642120000
[12335.689303] FS: 0000000000000000(0000) GS:ffff995739000000(0000) knlGS:0000000000000000
[12335.689323] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[12335.689341] CR2: 00007f43c5d5e039 CR3: 000000011c012005 CR4: 00000000000606e0
[12335.689360] Call Trace:
[12335.689377] <IRQ>
[12335.689418] ? rcu_read_lock_held_common+0x12/0x50
[12335.689447] ? rcu_read_lock_sched_held+0x25/0x80
[12335.689471] ? rcu_read_lock_held_common+0x12/0x50
[12335.689504] ath11k_dp_rx_process_mon_rings+0x8d/0x4f0 [ath11k]
[12335.689578] ? ath11k_dp_rx_process_mon_rings+0x8d/0x4f0 [ath11k]
[12335.689653] ? lock_acquire+0xef/0x360
[12335.689681] ? rcu_read_lock_sched_held+0x25/0x80
[12335.689713] ath11k_dp_service_mon_ring+0x38/0x60 [ath11k]
[12335.689784] ? ath11k_dp_rx_process_mon_rings+0x4f0/0x4f0 [ath11k]
[12335.689860] call_timer_fn+0xb2/0x2f0
[12335.689897] ? ath11k_dp_rx_process_mon_rings+0x4f0/0x4f0 [ath11k]
[12335.689970] run_timer_softirq+0x21f/0x540
[12335.689999] ? ktime_get+0xad/0x160
[12335.690025] ? lapic_next_deadline+0x2c/0x40
[12335.690053] ? clockevents_program_event+0x82/0x100
[12335.690093] __do_softirq+0x151/0x4a8
[12335.690135] irq_exit_rcu+0xc9/0x100
[12335.690165] sysvec_apic_timer_interrupt+0xa8/0xd0
[12335.690189] </IRQ>
[12335.690204] <TASK>
[12335.690225] asm_sysvec_apic_timer_interrupt+0x12/0x20
Reset the default value to HAL_INVALID_PEERID each time after memset
of ppdu_info as well as others memset which existed in function
ath11k_dp_rx_process_mon_status(), then the failed log disappeared.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 01d2f285e3 ("ath11k: decode HE status tlv")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220518033556.31940-1-quic_wgong@quicinc.com
Currently commit 1f682dc9fb ("ath11k: reduce the wait time of 11d scan
and hw scan while add interface") introduced a wait_for_completion_timeout
operation for ar->scan.completed, another one is existed in ath11k_scan_stop(),
then ath11k has two places to wait for the ar->scan.completed and they
run in different thread, thus it is possible to happend that the two
thread both enter wait status. To handle this scenario, ath11k should
change the complete() to complete_all() for the ar->scan.completed. This
also work well when it is only one thread wait for ar->scan.completed.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220919024413.25083-1-quic_wgong@quicinc.com
Add support for WoW on WCN6750 chipset.
Unlike other chips where WoW exit happens after sending WoW wakeup
WMI command, exit from WoW suspend in the case of WCN6750 happens
upon sending a WoW exit SMP2P (Shared memory point to point) message
to the firmware.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220902112520.24804-3-quic_mpubbise@quicinc.com
In current code STA_KEEPALIVE_ARP_RESPONSE TLV header is included only
when ARP method is used, this causes firmware always to crash when wowlan
is enabled because firmware needs it to be present no matter ARP method
is used or not.
Fix this issue by including STA_KEEPALIVE_ARP_RESPONSE TLV header by
default.
Also fix below typo:
s/WMI_TAG_STA_KEEPALVE_ARP_RESPONSE/WMI_TAG_STA_KEEPALIVE_ARP_RESPONSE/
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 0f84a156aa ("ath11k: Handle keepalive during WoWLAN suspend and resume")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220913044358.2037-1-quic_bqiang@quicinc.com
Fix documentation issues reported by kernel-doc:
- Incorrect use of /** for non-kernel-doc comments
- Mismatch between documented and actual identifiers
- Incorrect identifier syntax
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220909151246.22961-1-quic_jjohnson@quicinc.com
Increase TCL data ring size to 2048 for WCN6750. This is
needed to meet 160 MHz TX throughput.
Add a new hw_param to indicate the TX ring size for
individual devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-4-quic_mpubbise@quicinc.com
Currently in the case of WCN6750, only one TCL ring is used for TX,
this is limiting the TX throughput in 160 MHz case, enabling multiple
TCL rings on WCN6750 has shown an improvement of nearly 300 Mbps in
the case of TCP TX, therefore add the support of multi TX ring for
WCN6750.
Currently TCL ring is selected based on CPU ID, this logic cannot be
applied for WCN6750 as there is chance of out of order TX of packets
and to avoid this, choose TCL ring based on flow hash so that packets
of the same flow will end up on same TCL ring. For the same reason,
TCL ring retry logic is also not applicable for WCN6750.
Also the mapping of TCL, WBM & RBM IDs for WCN6750 is different from
existing devices. Create a new TCM/WBM/RBM mapping for WCN6750.
Change does not impact existing ath11k devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-3-quic_mpubbise@quicinc.com
Enable threaded NAPI on all ath11k targets. Unlike traditional
NAPI poll which runs in softirq context and on the core which
scheduled the NAPI, threaded NAPI makes use of kernel threads
which are under direct control of the scheduler and helps in
balancing the NAPI processing load across multiple CPUs thereby
improving throughput.
In the case of WCN6750, enabling threaded NAPI has improved
160 MHz RX throughput by nearly 400 Mbps. Similar gains can
be expected on other ath11k devices as well.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-2-quic_mpubbise@quicinc.com
mhi_alloc_controller() allocates a memory space for mhi_ctrl. When gets
some error, mhi_ctrl should be freed with mhi_free_controller(). But
when ath11k_mhi_read_addr_from_dt() fails, the function returns without
calling mhi_free_controller(), which will lead to a memory leak.
We can fix it by calling mhi_free_controller() when
ath11k_mhi_read_addr_from_dt() fails.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220907073704.58806-1-niejianglei2021@163.com
On-board SRAM contains valuable information for firmware debugging so
add a new file named "sram" to debugfs with which we can dump SRAM
content using following the following:
cp /sys/kernel/debug/ath11k/wcn6855\ hw2.0/sram /tmp/sram
Currently this feature is enabled for QCA6390 and WCN6855.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220802075533.1744-3-quic_bqiang@quicinc.com
ath11k_pcic_write32/read32 tries to do wake up before doing actual
write/read work, which means each time a u32 is written/read, wake
up is performed. This is not necessary in case where we do a
large amount of write/read, because only one time of wake up is needed.
So split each one into two parts, the first part does wake up and
release, and the second one does actual write/read work.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220802075533.1744-2-quic_bqiang@quicinc.com
Enable remain on channel support on WCN6750 as it is needed for
GAS, Passpoint.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080656.3450-1-quic_mpubbise@quicinc.com
The SMPS power save mode needs to be per-link rather than being shared
for all links. As such, move it into struct ieee80211_link_sta.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to connect to a non-transmit MBSSID AP profile.
Non-transmit MBSSID profile parameters are passed to the firmware
via WMI VDEV UP command and this helps firmware to track MBSSID
profile within the multi-BSS beacon and report beacon loss if
any.
WCN6750, QCA6390 & WCN6855 firmwares have the support and hence
enable the support on these hardwares.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080616.29414-1-quic_mpubbise@quicinc.com
Currently, creation of debugfs entries for TWT is failing during
hardware restart because of the residual TWT files which were
created during add_interface(). Since, struct arvif{} is memset
to zero upon add_interface() invocation, when the hardware restart
is triggered, arvif is memset to 0 and TWT files are attempted to
create again which will fail because of the residual TWT files
already in place, this leads to hardware restart failure.
Also, it is not a good idea to return error from add_interface()
because of debugfs file creation failures. Moreover, debugfs
framework can very well handle the errors in it's create file &
remove file APIs and the errors returned by these APIs are not
checked in most usecases.
Fix the HW restart failure by ignoring the errors returned from
the debugfs APIs.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: fe98a6137d ("ath11k: add debugfs for TWT debug calls")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720135150.22193-3-quic_mpubbise@quicinc.com
Currently TWT debugfs files required for manually testing the
TWT feature are created only for the AP interfaces; these debugfs
hooks are also required for the station interfaces in order to
test the TWT feature manually, therefore create these debugfs
hooks for station iftype as well.
In the case of station interfaces, TWT is entirely handled in the
firmware based on input parameters passed to it during association
via TWT enable WMI command. In order to manually test this feature,
firmware expects to first disable the TWT feature and then send the
enable command with sta_cong_timer_ms parameter set to 0.
This is true for WCN6750, QCA6390 & WCN6855 hardwares.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720135150.22193-2-quic_mpubbise@quicinc.com
Add cold boot calibration support on WCN6750. Unlike other
chipsets where firmware(FW) is restarted after cold boot
calibration is completed, it is recommended not to restart
the firmware for WCN6750.
For WCN6750, FW sends both CAL_DONE & FW_READY QMI indication
to the driver after cold boot calibration is completed.
QMI message flow for WCN6750 with cold boot support:
FW_INIT_DONE to HOST -> CALIBRATION Mode to FW -> CAL_DONE to Host ->
FW_READY to Host -> MODE_ON to FW
QMI message flow for other chipsets with cold boot support:
FW_INIT_DONE to Host -> CALIBRATION Mode to FW -> FW_READY to Host ->
Trigger FW restart -> FW_INIT_DONE to HOST -> MODE_ON to FW
QMI message flow for chipsets without cold boot support:
FW_INIT_DONE to Host -> MODE_ON to FW
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134909.15626-3-quic_mpubbise@quicinc.com
QMI message IDs for some of the QMI messages were incorrectly
defined in the original implementation. These have to be corrected
to enable cold boot support on WCN6750. These corrections are
applicable for all chipsets and will not impact them. Refactor the
code accordingly.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134909.15626-2-quic_mpubbise@quicinc.com
When the system shuts down, SMMU driver will be stopped and
will not assist in IOVA translations. SMMU driver expects all
of its consumers to shutdown before shutting down itself.
WCN6750 being one of the consumer device should not perform any
DMA operations after the SMMU has shutdown which will otherwise
result in SMMU faults.
SMMU driver will call the shutdown() callback of all its
consumer devices and the consumers shall stop further DMA
activity after the invocation of their respective shutdown()
callbacks.
Register the shutdown() callback to the platform core for WCN6750.
Change will not impact other AHB ath11k devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134710.15523-1-quic_mpubbise@quicinc.com
- Runtime verification infrastructure
This is the biggest change for this pull request. It introduces the
runtime verification that is necessary for running Linux on safety
critical systems. It allows for deterministic automata models to be
inserted into the kernel that will attach to tracepoints, where the
information on these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will then
activate a given reactor, that could just inform the user or even panic
the kernel (for which safety critical systems will detect and can recover
from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to be
confused with "work in progress"), and Wakeup While Not Running (WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace several
vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is left
off.
- The rest is various cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYu0yzRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qj4HAP4tQtV55rjj4DQ5XIXmtI3/64PmyRSJ
+y4DEXi1UvEUCQD/QAuQfWoT/7gh35ltkfeS4t3ockzy14rrkP5drZigiQA=
=kEtM
-----END PGP SIGNATURE-----
Merge tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Runtime verification infrastructure
This is the biggest change here. It introduces the runtime
verification that is necessary for running Linux on safety critical
systems.
It allows for deterministic automata models to be inserted into the
kernel that will attach to tracepoints, where the information on
these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will
then activate a given reactor, that could just inform the user or
even panic the kernel (for which safety critical systems will detect
and can recover from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to
be confused with "work in progress"), and Wakeup While Not Running
(WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace
several vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is
left off.
- The rest is various cleanups and fixes.
* tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (50 commits)
rv: Unlock on error path in rv_unregister_reactor()
tracing: Use alignof__(struct {type b;}) instead of offsetof()
tracing/eprobe: Show syntax error logs in error_log file
scripts/tracing: Fix typo 'the the' in comment
tracepoints: It is CONFIG_TRACEPOINTS not CONFIG_TRACEPOINT
tracing: Use free_trace_buffer() in allocate_trace_buffers()
tracing: Use a struct alignof to determine trace event field alignment
rv/reactor: Add the panic reactor
rv/reactor: Add the printk reactor
rv/monitor: Add the wwnr monitor
rv/monitor: Add the wip monitor
rv/monitor: Add the wip monitor skeleton created by dot2k
Documentation/rv: Add deterministic automata instrumentation documentation
Documentation/rv: Add deterministic automata monitor synthesis documentation
tools/rv: Add dot2k
Documentation/rv: Add deterministic automaton documentation
tools/rv: Add dot2c
Documentation/rv: Add a basic documentation
rv/include: Add instrumentation helper functions
rv/include: Add deterministic automata monitor definition via C macros
...
Commit 56c8ccf331 ("ath11k: Add register access logic for WCN6750")
regressed QCN9074. With the above mentioned commit, writes are failing
for some registers on QCN9074 although the device seems to work
normally.
ath11k_pci 0000:03:00.0: failed to set pcie link register0x01e0e0a8: 0xffffffff != 0x00000010
ath11k_pci 0000:03:00.0: failed to set sysclk: -110
PCIe devices in ath11k (QCA6390, WCN6855, QCN9074, WCN6750) use window
concept for register accesses. There are two schemes, dynamic & static
window.
In dynamic window scheme, a single window(region in the BAR) is mapped
either to CE or DP register windows at any give time. QCA6390 & WCN6855
follow this scheme for register accesses.
In static window scheme, CE & DP register windows are statically mapped
to separate regions with in the BAR so that there is no switching of
register windows between CE & DP register accesses. QCN9074 & WCN6750
follow this scheme although the window start offsets are different for
QCN9074 & WCN6750.
QCN9074 uses 3rd & 2nd window for DP & CE register accesses respectively
whereas WCN6750 uses 1st & 2nd window for DP & CE. In QCN9074, along with
2nd & 3rd windows, 1st window is also used for certain configurations
which commit 56c8ccf331 ("ath11k: Add register access logic for WCN6750")
did not account for and hence the regression.
Fix this by going back to the original way of accessing the registers on
QCN9074. Since this diverges from WCN6750 way of accessing registers, it
is required to register window_read32/window_write32() pci_ops for WCN6750.
We can also get rid of dp_window_idx & ce_window_idx members in hw_params,
so remove them.
Also add a new API ath11k_pcic_register_pci_ops() for registering pci_ops
to the ath11k core. This API checks for mandatory pci_ops() and reports
error if those are missing. Also initialize unused pci_ops to NULL.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Fixes: 56c8ccf331 ("ath11k: Add register access logic for WCN6750")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220608062954.27792-1-quic_mpubbise@quicinc.com
Recent mac80211 API changes introduced a long line warning in ath11k:
drivers/net/wireless/ath/ath11k/mac.c:1404: line length of 92 exceeds 90 columns
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220708170052.28615-1-kvalo@kernel.org
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224749.430339634@goodmis.org
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: ath11k@lists.infradead.org
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Since mac80211 already has a protected pointer to link_conf,
pass it to the driver to avoid additional RCU locking.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the capability to specify gfp_t parameter to
ieeee80211_obss_color_collision_notify routine since it runs in
interrupt context in ieee80211_rx_check_bss_color_collision().
Fixes: 6d945a33f2 ("mac80211: introduce BSS color collision detection")
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/02c990fb3fbd929c8548a656477d20d6c0427a13.1655419135.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix warnings reported by checkpatch tool. Below are the errors fixed,
drivers/net/wireless/ath/ath11k/hal_rx.c:760: 'recevied' may be misspelled - perhaps 'received?
drivers/net/wireless/ath/ath11k/qmi.c:2232: Prefer strscpy over strlcpy
drivers/net/wireless/ath/ath11k/qmi.c:2238: Prefer strscpy over strlcpy
drivers/net/wireless/ath/ath11k/qmi.c:2662: Prefer strscpy over strlcpy
drivers/net/wireless/ath/ath11k/mac.c:7836: 'atleast' may be misspelled - perhaps 'at least'?
drivers/net/wireless/ath/ath11k/wmi.c:6566: 'succeded' may be misspelled - perhaps 'succeeded'?
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220602131350.29486-1-quic_mpubbise@quicinc.com
Currently ar->ht_cap_info is not set anywhere in the code, this could
result in LDPC config computed wrongly in the set_bitrate_mask() hook
and eventually sending wrong config to the target. Fix this by checking
the LDPC support from the band HT capabilities of the radio instead.
Furthermore, it looks like firmwares running on the ath11k hardware
do not set WMI_HT_CAP_LDPC for advertising the TX LDPC capability,
WMI_HT_CAP_TX_LDPC is set instead and this should be checked for
getting hardware's TX LDPC support. This is true for QCA6390, WCN6855
& WCN6750 hardware.
Also, remove unused variables ht_cap_info & vht_cap_info from
struct ath11k{}.
Found this during code review.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220602124142.29909-1-quic_mpubbise@quicinc.com
Currently when firmware recovery is in progress, we do not queue REO
commands to the firmware, instead -ESHUTDOWN will be returned to the
caller leading to a failure print on the console. The REO command in
the problem scenario is sent for all tids of a peer in which case we
will have 16 failure prints on the console for a single peer. For an
AP usecase, this count would be even higher in a worst case scenario.
Since these commands are bound to fail during firmware recovery, it
is better to avoid printing these failures and thereby avoid message
flooding on the console.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: 8ee8d38ca4 ("ath11k: Fix crash during firmware recovery on reo cmd ring access")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220602122929.18896-1-quic_mpubbise@quicinc.com
Currently a couple of debug_mask entries are mapped to the same value,
this could enable unintended driver logging. If enabling DP_TX logs was
the intention, then this could also enable PCI logs flooding the dmesg
buffer or vice versa. Fix this by correctly assigning the debug masks.
Found during code review.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: aa2092a9ba ("ath11k: add raw mode and software crypto support")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220602115621.15339-1-quic_mpubbise@quicinc.com
On htc_tx_completion error the skb is not dropped. This is wrong since
the completion_handler logic expect the skb to be consumed anyway even
when an error is triggered. Not freeing the skb on error is a memory
leak since the skb won't be freed anywere else. Correctly free the
packet on eid >= ATH11K_HTC_EP_COUNT before returning.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: f951380a60 ("ath11k: Disabling credit flow for WMI path")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220528142516.20819-2-ansuelsmth@gmail.com
Currently mac80211 doesn't calculate average signal when RSS(Receive side
scaling) is enabled from the driver, so average signal isn't printed in
the station dump. To address this issue, calculate the average signal
from RSSI within driver and display in the station dump.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Signed-off-by: Thiraviyam Mariyappan <quic_tmariyap@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1652965061-30457-1-git-send-email-quic_tmariyap@quicinc.com
Make sure to clear the IRQ affinity hint also on shutdown to avoid
triggering a WARN_ON_ONCE() in __free_irq() when stopping MHI while
using a single MSI vector.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: e94b07493d ("ath11k: Set IRQ affinity to CPU0 in case of one MSI vector")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220523143258.24818-1-johan+linaro@kernel.org
Make sure to allocate resources needed before registering the device.
This specifically avoids having a racing open() trigger a BUG_ON() in
mod_timer() when ath11k_mac_op_start() is called before the
mon_reap_timer as been set up.
I did not see this issue with next-20220310, but I hit it on every probe
with next-20220511. Perhaps some timing changed in between.
Here's the backtrace:
[ 51.346947] kernel BUG at kernel/time/timer.c:990!
[ 51.346958] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
...
[ 51.578225] Call trace:
[ 51.583293] __mod_timer+0x298/0x390
[ 51.589518] mod_timer+0x14/0x20
[ 51.595368] ath11k_mac_op_start+0x41c/0x4a0 [ath11k]
[ 51.603165] drv_start+0x38/0x60 [mac80211]
[ 51.610110] ieee80211_do_open+0x29c/0x7d0 [mac80211]
[ 51.617945] ieee80211_open+0x60/0xb0 [mac80211]
[ 51.625311] __dev_open+0x100/0x1c0
[ 51.631420] __dev_change_flags+0x194/0x210
[ 51.638214] dev_change_flags+0x24/0x70
[ 51.644646] do_setlink+0x228/0xdb0
[ 51.650723] __rtnl_newlink+0x460/0x830
[ 51.657162] rtnl_newlink+0x4c/0x80
[ 51.663229] rtnetlink_rcv_msg+0x124/0x390
[ 51.669917] netlink_rcv_skb+0x58/0x130
[ 51.676314] rtnetlink_rcv+0x18/0x30
[ 51.682460] netlink_unicast+0x250/0x310
[ 51.688960] netlink_sendmsg+0x19c/0x3e0
[ 51.695458] ____sys_sendmsg+0x220/0x290
[ 51.701938] ___sys_sendmsg+0x7c/0xc0
[ 51.708148] __sys_sendmsg+0x68/0xd0
[ 51.714254] __arm64_sys_sendmsg+0x28/0x40
[ 51.720900] invoke_syscall+0x48/0x120
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Fixes: 840c36fa72 ("ath11k: dp: stop rx pktlog before suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220517103436.15867-1-johan+linaro@kernel.org
As part of adding the support of WCN6750 to ath11k, bus_params
were moved to hw_params and this regressed the initialization
of WCN6750. By the time AHB resources are setup for WCN6750,
hw_params will not be initialized and therefore initialization
for WCN6750 will fail. This is applicable only for WCN6750,
no other device is impacted.
Fix this by moving the initialization of hw_params before
setting up AHB resources.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: 00402f49d2 ("ath11k: Add support for WCN6750 device")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220517055241.15885-1-quic_mpubbise@quicinc.com
We are seeing below warning:
warn: variable dereferenced before check 'sar'
Fix it by moving ahead pointer check on 'sar'.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 652f69ed9c ("ath11k: Add support for SAR")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220517004844.2412660-1-quic_bqiang@quicinc.com
Update the missing MU-MIMO/OFDMA info in PDEV RX,
trigger and schedule stats. i.e HTT stats type 10, 12 and 17
respectively.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4-01209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1652152236-12038-1-git-send-email-quic_srirrama@quicinc.com
This patch adds the new struct ieee80211_rate_status and replaces
'struct rate_info *rate' in ieee80211_tx_status with pointer and length
annotation.
The struct ieee80211_rate_status allows to:
(1) receive tx power status feedback for transmit power control (TPC)
per packet or packet retry
(2) dynamic mapping of wifi chip specific multi-rate retry (mrr)
chains with different lengths
(3) increase the limit of annotatable rate indices to support
IEEE802.11ac rate sets and beyond
ieee80211_tx_info, control and status buffer, and ieee80211_tx_rate
cannot be used to achieve these goals due to fixed size limitations.
Our new struct contains a struct rate_info to annotate the rate that was
used, retry count of the rate and tx power. It is intended for all
information related to RC and TPC that needs to be passed from driver to
mac80211 and its RC/TPC algorithms like Minstrel_HT. It corresponds to
one stage in an mrr. Multiple subsequent instances of this struct can be
included in struct ieee80211_tx_status via a pointer and a length variable.
Those instances can be allocated on-stack. The former reference to a single
instance of struct rate_info is replaced with our new annotation.
An extension is introduced to struct ieee80211_hw. There are two new
members called 'tx_power_levels' and 'max_txpwr_levels_idx' acting as a
tx power level table. When a wifi device is registered, the driver shall
supply all supported power levels in this list. This allows to support
several quirks like differing power steps in power level ranges or
alike. TPC can use this for algorithm and thus be designed more abstract
instead of handling all possible step widths individually.
Further mandatory changes in status.c, mt76 and ath11k drivers due to the
removal of 'struct rate_info *rate' are also included.
status.c already uses the information in ieee80211_tx_status->rate in
radiotap, this is now changed to use ieee80211_rate_status->rate_idx.
mt76 driver already uses struct rate_info to pass the tx rate to status
path. The new members of the ieee80211_tx_status are set to NULL and 0
because the previously passed rate is not relevant to rate control and
accurate information is passed via tx_info->status.rates.
For ath11k, the txrate can be passed via this struct because ath11k uses
firmware RC and thus the information does not interfere with software RC.
Compile-Tested: current wireless-next tree with all flags on
Tested-on: Xiaomi 4A Gigabit (MediaTek MT7603E, MT7612E) with OpenWrt
Linux 5.10.113
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://lore.kernel.org/r/20220509173958.1398201-2-jelonek.jonas@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The variables vht_mcs and he_mcs are being initialized in the
start of for-loops however they are re-assigned new values in
the loop and not used outside the loop. The initializations
are redundant and can be removed.
Cleans up clang scan warnings:
warning: Although the value stored to 'vht_mcs' is used in the
enclosing expression, the value is never actually read from
'vht_mcs' [deadcode.DeadStores]
warning: Although the value stored to 'he_mcs' is used in the
enclosing expression, the value is never actually read from
'he_mcs' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220507184155.26939-1-colin.i.king@gmail.com
Ath11k allocates memory when firmware requests memory in QMI.
Coldboot calibration and firmware recovery uses firmware reload.
On firmware reload, firmware sends memory request again. If Ath11k
allocates memory on first firmware boot, reuse the available
memory. Also check if the segment type and size is same
on the next firmware boot. Reuse if segment type/size is
same as previous firmware boot else free the segment and
allocate the segment with size/type.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00752-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506141448.10340-1-quic_akolli@quicinc.com
In case of Passpoint, the WLAN interface may be requested to
remain on a specific channel and then to send some management
frames on that channel. Now chanfreq of wmi_mgmt_send_cmd is set
as 0, as a result firmware may choose a default but wrong channel.
Fix it by assigning chanfreq field with the designated channel.
This change only applies to WCN6855 and QCA6390, other chips are
not affected.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-4-quic_bqiang@quicinc.com
Commit 66307ca040 ("ath11k: fix mgmt_tx_wmi cmd sent to FW for
deleted vdev") wants both of below two conditions are true before
sending management frames:
1: ar->allocated_vdev_map & (1LL << arvif->vdev_id)
2: arvif->is_started
Actually the second one is not necessary because with the first one
we can make sure the vdev is present.
Also use ar->conf_mutex to synchronize vdev delete and mgmt. TX.
This issue is found in case of Passpoint scenario where ath11k
needs to send action frames before vdev is started.
Fix it by removing the second condition.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Fixes: 66307ca040 ("ath11k: fix mgmt_tx_wmi cmd sent to FW for deleted vdev")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-3-quic_bqiang@quicinc.com
Add remain on channel support, it is needed in several
scenarios such as Passpoint etc.
Currently this is supported by QCA6390, WCN6855, IPQ8074,
IPQ6018 and QCN9074.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-2-quic_bqiang@quicinc.com
With WoWLAN enabled and after sleeping for a rather long time,
we are seeing that with some APs, it is not able to wake up
the STA though the correct wake up pattern has been configured.
This is because the host doesn't send keepalive command to
firmware, thus firmware will not send any packet to the AP and
after a specific time the AP kicks out the STA.
Fix this issue by enabling keepalive before going to suspend
and disabling it after resume back.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506012540.1579604-1-quic_bqiang@quicinc.com
When doing simulate_fw_crash operation periodically with a short interval
time such as 10 seconds, it is easy happened WMI command timed out for
WMI_SCAN_CHAN_LIST_CMDID in ath11k_reg_update_chan_list().
log:
[42287.610053] ath11k_pci 0000:01:00.0: wmi command 12291 timeout
[42287.610064] ath11k_pci 0000:01:00.0: failed to send WMI_SCAN_CHAN_LIST cmd
[42287.610073] ath11k_pci 0000:01:00.0: failed to perform regd update : -11
Note that this issue does not occur with a longer interval such as 20 seconds.
The reason the issue occurs with a shorter interval is the following steps:
1) Upon initial boot, or after device recovery, the initial hw scan plus
the 11d scan will run, and when 6 GHz support is present, these scans
can take up to 12 seconds to complete, so ath11k_reg_update_chan_list()
is still waiting the completion of ar->completed_11d_scan.
2) If a simulate_fw_crash operation is received during this time, those
scans do not complete, and ath11k_core_pre_reconfigure_recovery()
complete the ar->completed_11d_scan, then ath11k_reg_update_chan_list()
wakeup and start to send WMI_SCAN_CHAN_LIST_CMDID, but firmware is crashed
at this moment, so wmi timed out occur.
To address this issue, reset the 11d state during device recovery so that
WMI_SCAN_CHAN_LIST_CMDID does not timed out for short interval time such
as 10 seconds.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 1f682dc9fb ("ath11k: reduce the wait time of 11d scan and hw scan while add interface")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220505034636.29582-1-quic_wgong@quicinc.com
The offset of REO register where the RX fragment destination ring
is configured is different in WCN6750 as compared to WCN6855.
Due to this differnce in offsets, on WCN6750, fragment destination
ring will be configured incorrectly, leading to RX fragments not
getting delivered to the driver. Fix this by defining HW specific
offsets for the REO MISC CTL register.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220504083900.31513-1-quic_mpubbise@quicinc.com
checkpatch warns:
drivers/net/wireless/ath/ath11k/mac.c:7760: line length of 91 exceeds 90 columns
This was introduced by commit 046d2e7c50 ("mac80211: prepare sta handling for
MLO support").
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220503060415.24499-1-kvalo@kernel.org
Add the support to attach WCN6750 and map iommu domain
for targets which do not have the support of TrustZone.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328062032.28881-1-quic_mpubbise@quicinc.com
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
* wfx: silicon labs devices
* plfxlc: pureLiFi X, XL, XC devices
mac80211
* host based BSS color collision detection
* prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
* support TP-Link T2E devices
rtw89
* support firmware crash simulation
* preparation for 8852ce hardware support
ath11k
* Wake-on-WLAN support for QCA6390 and WCN6855
* device recovery (firmware restart) support for QCA6390 and WCN6855
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
wcn36xx
* support for transmit rate reporting to user space
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmJxS2sRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuNgwf9H2oxMKLKrlFoX1qHtNBwZuHS6IERhOkM
NI9DjS4MCyiUSbA5r3sWlpqXQeKIbG/05gUZ6Y0ircGFwnAGjZ6isPwo8pKFgbh5
QljXQjUTHbkshrXW8K+VGJxw4F1oiPlOGUDVdXPy2FLx5ZvBlaUV2rWQUzsWX9I0
EnrM6ygHBVejVYDe+JSkb1gzb/07xuZN410IJPuZTPKJfYiE0oGU3zpTbExFitaz
ObjfFUWqHrVue525WFAJ9Dbk8kYEKyMThr7rkkWekYJjujJLJo0qhEiZVZu0eEsk
Vq4PdKmQAqlgbShQ/3Mv8BRsSH2wy62+zKjPWL+8t4Gmm9DbLu+++A==
=T7Ii
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
- wfx: silicon labs devices
- plfxlc: pureLiFi X, XL, XC devices
mac80211
- host based BSS color collision detection
- prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
- support TP-Link T2E devices
rtw89
- support firmware crash simulation
- preparation for 8852ce hardware support
ath11k
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support for QCA6390 and WCN6855
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- support for WCN6750
wcn36xx
- support for transmit rate reporting to user space
* tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (228 commits)
rtw89: 8852c: rfk: add DPK
rtw89: 8852c: rfk: add IQK
rtw89: 8852c: rfk: add RX DCK
rtw89: 8852c: rfk: add RCK
rtw89: 8852c: rfk: add TSSI
rtw89: 8852c: rfk: add LCK
rtw89: 8852c: rfk: add DACK
rtw89: 8852c: rfk: add RFK tables
plfxlc: fix le16_to_cpu warning for beacon_interval
rtw88: remove a copy of the NAPI_POLL_WEIGHT define
carl9170: tx: fix an incorrect use of list iterator
wil6210: use NAPI_POLL_WEIGHT for napi budget
ath10k: remove a copy of the NAPI_POLL_WEIGHT define
ath11k: Add support for WCN6750 device
ath11k: Datapath changes to support WCN6750
ath11k: HAL changes to support WCN6750
ath11k: Add QMI changes for WCN6750
ath11k: Fetch device information via QMI for WCN6750
ath11k: Add register access logic for WCN6750
ath11k: Add HW params for WCN6750
...
====================
Link: https://lore.kernel.org/r/20220503153622.C1671C385A4@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ath.git patches for v5.19. Major changes:
ath11k
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
WCN6750 is non-DBS 2x2 11AX chipset. Unlike QCA6390 which is a
DBS (dual band simultaneous) solution (2 LMACs), WCN6750 has a
single LMAC supporting 2G, 5G and 6G bands but will operate only
on one band at any given point.
WCN6750 is a PCIe based solution, but it is attached to the WPSS
(Wireless Processor SubSystem) Q6 processor, hence it is enumerated
by the Q6 processor. It is registered to the APSS processor
(Application Processor SubSystem) as a platform device(AHB) and
remoteproc APIs are used to boot up or shutdown the device like
other AHB devices.
Also, Device information like BAR and it's size is not known to the
APSS processor as the chip is enumerated by WPSS Q6. These details
are fetched over QMI.
STA and AP modes are supported. Verified basic connectivity and ping
in both the modes.
An important point to note is that though WCN6750 is a PCIe device,
it cannot be attached to any other platform except on Qualcomm
Snapdragon SoCs due to the aforementioned reasons.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-10-quic_mpubbise@quicinc.com
HAL RX descriptor for WCN6750 is same as QCN9074, this
means that the size of the HAL RX decriptor and the DP
APIs that WCN6750 requires to enable datapath should be
initialized with that of QCN9074's RX descriptor size
and the DP APIs respectively. There is one change wrt to
REO configuration though, REO configuration for WCN6750
follows WCN6855, therefore use reo_setup() of WCN6855
for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-9-quic_mpubbise@quicinc.com
Add HAL changes required to support WCN6750. Offsets of some registers
for WCN6750 are different from other supported devices; move such
register offsets to platform specific ath11k_hw_regs.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-8-quic_mpubbise@quicinc.com
In the case of WCN6750, FW doesn't request for DDR memory
via QMI, instead it uses a fixed 12MB reserved Memory region
in the DDR which is called as MSA region. As a result, QMI
message sequence is not same as other ath11k supported devices.
Also, M3 firmware will be bundled into the FW and will be
downloaded to the target as part of Q6 boot.
This is the QMI flow in the case of WCN6750,
1) QMI firmware indication REQ/RESP
2) QMI host capability REQ/RESP
3) QMI target capability REQ/RESP
4) QMI device info REQ/RESP
5) QMI BDF download
6) QMI FW ready
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-7-quic_mpubbise@quicinc.com
Since WPPS Q6 does the PCIe enumeration of WCN6750, device
information like BAR and BAR size is not known to the APPS
processor (Application Processor SubSystem). In order to
fetch these details, a QMI message called device info request
will be sent to the target. Therefore, add logic to fetch
BAR details from the target.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-6-quic_mpubbise@quicinc.com
WCN6750 uses static window mapping to access the HW registers.
Unlike QCN9074 which uses 3rd window for UMAC and 2nd window
for CE register access, WCN6750 uses 1st window for UMAC
and 2nd window for CE registers.
Also, refactor the code so that WCN6750 can use the existing
ath11k_pci_read32/write32() APIs for accessing the registers.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-5-quic_mpubbise@quicinc.com
WCN6750 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
A new variable hybrid_bus_type is defined in hw_params to indicate the
hybrid nature of the device.
Add HW params for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-4-quic_mpubbise@quicinc.com
In ath11k, bus_params were added with an intention to hold
parameters related to bus (AHB/PCI), but this is not true
as some bus parameters being different between chipsets of
the same bus.
With the addition of WCN6750 to ath11k, bus parameters are
going to be entirely different among AHB devices. Therefore,
it is wise to move bus_params to hw_params and get rid of
bus_params entirely.
Also, mhi_support parameter is not used anywhere in the driver,
remove it from bus_params.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-3-quic_mpubbise@quicinc.com
In the phase of wlan load, it has hw scan and 11d scan which sent to
firmware by ath11k, then hw scan and 11d scan will use about 14 seconds,
and meanwhile ath11k_reg_update_chan_list() is running in workqueue of
ath11k_base, and wait for 11d scan/hw scan finished. When the hw scan
finished, mac80211 will start to connect and send management packet,
at this moment, ath11k_reg_update_chan_list() is still waiting for 11d
scan finished, so wmi_mgmt_tx_work of ath11k will not run and thus the
tx management packet also not send out and lead authentication timed
out.
log:
INFO kernel: [ 187.885322] wlan0: authenticate with 72:6c:57:43:9f:90
INFO kernel: [ 187.937266] wlan0: send auth to 72:6c:57:43:9f:90 (try 1/3)
INFO kernel: [ 188.626944] wlan0: send auth to 72:6c:57:43:9f:90 (try 2/3)
INFO kernel: [ 189.650999] wlan0: send auth to 72:6c:57:43:9f:90 (try 3/3)
INFO kernel: [ 190.651917] wlan0: authentication with 72:6c:57:43:9f:90 timed out
Change wmi_mgmt_tx_work to another queue workqueue_aux of ath11k_base,
then connection success.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220428023320.4007-1-quic_wgong@quicinc.com
When test connect/disconnect to an AP frequently with WCN6855, sometimes
it show below log.
[ 277.040121] wls1: deauthenticating from 8c:21:0a:b3:5a:64 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 277.050906] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050944] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050954] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050961] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.050967] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 277.050976] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050983] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050989] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050995] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.051000] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 278.064050] ath11k_pci 0000:05:00.0: failed to request fw stats: -110
Reason is:
When running disconnect operation, sta_info removed from local->sta_hash
by __sta_info_destroy_part1() from __sta_info_flush(), after this,
ieee80211_find_sta_by_ifaddr() which called by
ath11k_wmi_tlv_fw_stats_data_parse() and ath11k_wmi_tlv_rssi_chain_parse()
cannot find this station, then failed log printed.
steps are like this:
1. when disconnect from AP, __sta_info_destroy() called __sta_info_destroy_part1()
and __sta_info_destroy_part2().
2. in __sta_info_destroy_part1(), it has "sta_info_hash_del(local, sta)"
and "list_del_rcu(&sta->list)", it will remove the ieee80211_sta from the
list of ieee80211_hw.
3. in __sta_info_destroy_part2(), it called drv_sta_state()->ath11k_mac_op_sta_state(),
then peer->sta is clear at this moment.
4. in __sta_info_destroy_part2(), it then called sta_set_sinfo()->drv_sta_statistics()
->ath11k_mac_op_sta_statistics(), then WMI_REQUEST_STATS_CMDID sent to firmware.
5. WMI_UPDATE_STATS_EVENTID reported from firmware, at this moment, the
ieee80211_sta can not be found again because it has remove from list in
step2 and also peer->sta is clear in step3.
6. in __sta_info_destroy_part2(), it then called cleanup_single_sta()->
sta_info_free()->kfree(sta), at this moment, the ieee80211_sta is freed
in memory, then the failed log will not happen because function
ath11k_mac_op_sta_state() will not be called.
Actually this print log is not a real error, it is only to skip parse the
info, so change to skip print by default debug setting.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220428022426.2927-1-quic_wgong@quicinc.com
This read the country code from SMBIOS and send the country code
to firmware, firmware will indicate the regulatory domain info of the
country code and then ath11k will use the info.
dmesg:
[ 1242.637173] ath11k_pci 0000:02:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0200
[ 1242.637176] ath11k_pci 0000:02:00.0: fw_version 0x110b09e5 fw_build_timestamp 2021-06-22 09:32 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02533-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
[ 1242.637253] ath11k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS
[ 1242.637259] ath11k_pci 0000:02:00.0: bdf variant name not found.
[ 1242.637261] ath11k_pci 0000:02:00.0: SMBIOS bdf variant name not set.
[ 1242.637263] ath11k_pci 0000:02:00.0: DT bdf variant name not set.
[ 1242.927543] ath11k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220421023501.32167-1-quic_wgong@quicinc.com
Currently, WBM idle ring HP is updated much before the shadow
configuration is sent to the FW. Any update to the shadow
registers before FW mode on request would not be reflected
on to the actual HW registers failing to bring up the device.
Send FW mode ON QMI request before WBM idle ring HP update
to fix this problem.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-12-quic_mpubbise@quicinc.com
WCN6750 is a single PDEV non-DBS chip which supports 2G, 5G and 6G bands.
It is a single LMAC device which can be either hooked to 2G/5G/6G bands.
Add WMI changes to support WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-11-quic_mpubbise@quicinc.com
Though WCN6750 is a single PDEV device, it is not a
DBS solution. So, do not put HW in DBS mode for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-10-quic_mpubbise@quicinc.com
drivers/net/wireless/ath/ath11k/mac.c:8175:13: error: ‘ath11k_mac_op_ipv6_changed’ defined but not used [-Werror=unused-function]
static void ath11k_mac_op_ipv6_changed(struct ieee80211_hw *hw,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Wrap it with #ifdef block to fix this.
Fixes: c3c36bfe99 ("ath11k: support ARP and NS offload")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220411020843.10284-1-yuehaibing@huawei.com
Add the missing unlock before return from function ath11k_wow_op_resume()
in the error handling case.
Fixes: 90bf5c8d0f ("ath11k: purge rx pktlog when entering WoW")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220408030912.3087293-1-yangyingliang@huawei.com
Add ath11k_mac_op_set_bios_sar_specs() to ath11k_ops, this function is called
when user space application calls NL80211_CMD_SET_SAR_SPECS. ath11k also
registers SAR type and frequency ranges to wiphy so user space can query SAR
capabilities.
This feature is currently enabled for WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-3-quic_bqiang@quicinc.com
When the WMI service bits are reported from firmware they are divided into
multiple segments, with 128 bits in each segment. The first segment is
processed by ath11k_wmi_service_bitmap_copy(), the second segment is processed
by ath11k_service_available_event() with WMI_TAG_SERVICE_AVAILABLE_EVENT. When
the service bit exceed 256 bits, then firmware reports it by tag
WMI_TAG_ARRAY_UINT32 in WMI_SERVICE_AVAILABLE_EVENTID.
Currently ath11k does not process the third segment. Upcoming features
need to know if firmware support is available for the features, so add
processing of the third segment.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-2-quic_bqiang@quicinc.com
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add ieee80211_rx_check_bss_color_collision routine in order to introduce
BSS color collision detection in mac80211 if it is not supported in HW/FW
(e.g. for mt7915 chipset).
Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify
BSS color collision detection is supported in HW/FW. Set this for ath11k
which apparently didn't need this code.
Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org
[clarify commit message a bit, move flag to mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to have goto for a return statement, so simplify the code. While at it,
print warning messages if power up calls fail.
No functional changes.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401173042.17467-4-kvalo@kernel.org
While reviewing the mhi.c I noticed we were just ignoring the errors coming
from MHI subsystem during suspend and resume. Add proper checks and warning
messages. Also pass the error value to callers.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401173042.17467-3-kvalo@kernel.org
State machines are difficult to understand and in this case it's just useless,
which is shown by the diffstat. So remove it entirely to make the code simpler.
No functional changes.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401173042.17467-2-kvalo@kernel.org
The intended delay in ath11k_core_suspend is introduced in commit
d1b0c33850 ("ath11k: implement suspend for QCA6390 PCI devices"),
now with ath11k_mac_wait_tx_complete added in commit ba9177fcef
("ath11k: Add basic WoW functionalities"), that delay is not
necessary now, so remove it.
This is found in code review.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220331002105.1162099-1-quic_bqiang@quicinc.com
The maximum number of SSIDs in a for active probe requests is currently
reported as 16 (WLAN_SCAN_PARAMS_MAX_SSID) when registering the driver.
The scan_req_params structure only has the capacity to hold 10 SSIDs.
This leads to a buffer overflow which can be triggered from
wpa_supplicant in userspace. When copying the SSIDs into the
scan_req_params structure in the ath11k_mac_op_hw_scan route, it can
overwrite the extraie pointer.
Firmware supports 16 ssid * 4 bssid, for each ssid 4 bssid combo probe
request will be sent, so totally 64 probe requests supported. So
set both max ssid and bssid to 16 and 4 respectively. Remove the
redundant macros of ssid and bssid.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01300-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220329150221.21907-1-quic_kathirve@quicinc.com
Remove core PCI and ath11k PCI references(struct ath11k_pci)
from PCI common code. Since, PCI common code will be used
by hybrid bus devices, this code should be independent
from ATH11K PCI references and Linux core PCI references
like struct pci_dev.
Since this change introduces function callbacks for bus wakeup
and bus release operations, wakeup_mhi HW param is no longer
needed and hence it is removed completely. Alternatively, bus
wakeup/release ops for QCA9074 are initialized to NULL as
QCA9704 does not need bus wakeup/release for register accesses.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-6-quic_mpubbise@quicinc.com
Refactor MSI logic in order to support hybrid bus devices
like WCN6750.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-5-quic_mpubbise@quicinc.com
Instead of selecting MSI config based on magic numbers, make
the assignment based on HW revision. The logic is similar to
the selection of HW params. This improves readability of the
code and also simplifies new additions.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-4-quic_mpubbise@quicinc.com
Unlike other ATH11K PCIe devices which are enumerated by APSS
processor (Application Processor SubSystem), WCN6750 gets
enumerated by the WPSS Q6 processor (Wireless Processor SubSystem);
In simple terms, though WCN6750 is PCIe device, it is not attached
to the APSS processor, APSS will not know of such a device being
present in the system and therefore WCN6750 will be registered as
a platform device to the kernel core like other supported AHB
devices.
WCN6750 needs both AHB and PCI APIs for it's operation, it uses
AHB APIs for device probe/boot and PCI APIs for device setup and
register accesses. Because of this nature, it is referred as a
hybrid bus device.
Refactor PCI code to support hybrid bus devices like WCN6750.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-3-quic_mpubbise@quicinc.com
In order to add the support for WCN6750 in ATH11K , it is
required to move certain PCI definitions to the header file.
As a result, add ATH11K_PCI_* prefix to these definitions.
Also, change the scope of certain PCI APIs that are required
to enable WCN6750 from static to global.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-2-quic_mpubbise@quicinc.com
This reverts commit 743b9065fe.
The original commit breaks the 256 bitmap in blockack frames in AP
mode. After reverting the commit the feature works again in both AP and
mesh modes
Tested-on: IPQ8074 hw2.0 PCI WLAN.HK.2.6.0.1-00786-QCAHKSWPL_SILICONZ-1
Fixes: 743b9065fe ("ath11k: mesh: add support for 256 bitmap in blockack frames in 11ax")
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1648701477-16367-1-git-send-email-quic_akolli@quicinc.com
Currently ath11k will wait 11d scan complete while add interface in
ath11k_mac_op_add_interface(), when system resume without enable
wowlan, ath11k_mac_op_add_interface() is called for each resume, thus
it increase the resume time of system. And ath11k_mac_op_hw_scan()
after ath11k_mac_op_add_interface() also needs some time cost because
the previous 11d scan need more than 5 seconds when 6 GHz is enabled,
then the scan started event will indicated to ath11k after the 11d
scan completed.
While 11d scan/hw scan is running in firmware, if ath11k update channel
list to firmware by WMI_SCAN_CHAN_LIST_CMDID, then firmware will cancel
the current scan which is running, it lead the scan failed. The patch
commit 9dcf6808b2 ("ath11k: add 11d scan offload support") used
finish_11d_scan/finish_11d_ch_list/pending_11d to synchronize the 11d
scan/hw scan/channel list between ath11k/firmware/mac80211 and to avoid
the scan fail.
Add wait operation before ath11k update channel list, function
ath11k_reg_update_chan_list() will wait until the current 11d scan/hw
scan completed. And remove the wait operation of start 11d scan and
waiting channel list complete in hw scan. After these changes, resume
time cost reduce about 5 seconds and also hw scan time cost reduced
obviously, and scan failed not seen.
The 11d scan is sent to firmware only one time for each interface added
in mac.c, and it is moved after the 1st hw scan because 11d scan will
cost some time and thus leads the AP scan result update to UI delay.
Currently priority of ath11k's hw scan is WMI_SCAN_PRIORITY_LOW, and
priority of 11d scan in firmware is WMI_SCAN_PRIORITY_MEDIUM, then the
11d scan which sent after hw scan will cancel the hw scan in firmware,
so change the priority to WMI_SCAN_PRIORITY_MEDIUM for the hw scan which
is in front of the 11d scan, thus it will not happen scan cancel in
firmware.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 9dcf6808b2 ("ath11k: add 11d scan offload support")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328035832.14122-1-quic_wgong@quicinc.com
Currently ath11k does not send the country code to firmware after device
recovery, as a result the regdomain info is reported from firmware by
default. Regdomain info is important, so ath11k also need to restore
it to the value which was used before recovery.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220324011856.11014-1-quic_wgong@quicinc.com
When more clients (128) are connected, the UL data traffic
KPI measurement is low compared to single client. This issue
is due to more CPU cycles spent on the peer lookup operation
with more clients. So reduce the peer lookup operation by
modifying the linear based lookup operation into the rhash
based lookup operation. This improve the peak throughput
measurement. Since this is a software algorithm change, it is
applicable for all the platforms.
TCP UL 128 Clients test case Observation (64bit system):
Previous: ~550 Mbps
Now : ~860 Mbps
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644036628-5334-1-git-send-email-quic_periyasa@quicinc.com
This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220315104721.26649-3-quic_wgong@quicinc.com
In Qualcomm ARM platforms there is WL_EN pin and other power regulators
which can be controlled at platform side to completely reset the chip.
For most of x86 and other platforms, the chip is connected via PCIe M.2
interface, and there is no way to control WL_EN pin. Instead the host
driver needs to reset the chip via PCIE_SOC_GLOBAL_RESET hardware
register, just like ath11k does currently.
But when using PCIE_SOC_GLOBAL_RESET there are some hardware registers
which are not cleared/restored. To handle those cases we can enable
PLATFORM_CAP_PCIE_GLOBAL_RESET QMI host capability to tell the firmware
to do some platform specific operations after firmware download.
This does not fix any known issues, but is recommended by the firmware
team, so enable the capability on QCA6390 and WCN6855 PCI devices. It is
currently unclear if this should be enabled also on QCN9074, so leave it
disabled for now. On AHB devices this is not needed as they don't use
PCIE_SOC_GLOBAL_RESET.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211011055602.77342-1-bqiang@codeaurora.org
Add hw-restart to directly restart wlan. Like UTF mode start it will
restart hardware and download firmware again.
Usage:
1. Run command:
echo hw-restart > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash
echo hw-restart > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash
2. wlan will be restart and do recovery process and success.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-4-quic_wgong@quicinc.com
ieee80211_reconfig() of mac80211 is the main function for recovery of
each ieee80211_hw and ath11k, and ath11k_core_reconfigure_on_crash()
is the main function for recovery of ath11k_base, it has more than
one ieee80211_hw and ath11k for each ath11k_base, so it need to add
synchronization between them, otherwise it has many issue.
For example, when ath11k_core_reconfigure_on_crash() is not complete,
mac80211 send a hw scan request to ath11k, it leads firmware crash,
because firmware has not been initialized at that moment, firmware
is only finished downloaded and loaded, it can not receive scan
command.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-3-quic_wgong@quicinc.com
Currently ath11k has device recovery logic, it is introduced by this
patch "ath11k: Add support for subsystem recovery" which is upstream
by https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git/commit/?h=ath11k-bringup&id=3a7b4838b6f6f234239f263ef3dc02e612a083ad.
The patch is for AHB devices such as IPQ8074, it has remote proc module
which is used to download the firmware and boots the processor which
firmware is running on. If firmware crashed, remote proc module will
detect it and download and boot firmware again. Below command will
trigger a firmware crash, and then user can test feature of device
recovery.
Test command:
echo assert > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash
echo assert > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash
Unfortunately, QCA6390 is PCIe bus, it does not have the remote proc
module, it use mhi module to communicate between firmware and ath11k.
So ath11k does not support device recovery for QCA6390 currently.
This patch is to add the extra logic which is different for QCA6390.
When firmware crashed, MHI_CB_EE_RDDM event will be indicate by
firmware and then ath11k_mhi_op_status_cb which is the callback of
mhi_controller will receive the MHI_CB_EE_RDDM event, then ath11k
will start to do recovery process, ath11k_core_reset() calls
ath11k_hif_power_down()/ath11k_hif_power_up(), then the mhi/ath11k
will start to download and boot firmware. There are some logic to
avoid deadloop recovery and two simultaneous recovery operations.
And because it has muti-radios for the soc, so it add some logic
in ath11k_mac_op_reconfig_complete() to make sure all radios has
reconfig complete and then complete the device recovery.
Also it add workqueue_aux, because ab->workqueue is used when receive
ATH11K_QMI_EVENT_FW_READY in recovery process(queue_work(ab->workqueue,
&ab->restart_work)), and ath11k_core_reset will wait for max
ATH11K_RESET_TIMEOUT_HZ for the previous restart_work finished, if
ath11k_core_reset also queued in ab->workqueue, then it will delay
restart_work of previous recovery and lead previous recovery fail.
ath11k recovery success for QCA6390/WCN6855 after apply this patch.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-2-quic_wgong@quicinc.com
Currently it does not have regdb files for QCA6390, so disable its regdb
support feature now.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220319023543.14288-3-quic_wgong@quicinc.com
Currently ATH11K_BD_IE_BOARD_EXT is not used, so remove it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220319023543.14288-2-quic_wgong@quicinc.com
ath11k_peer_find_by_addr states via lockdep that ab->base_lock must be
held when calling that function in order to protect the list. All
callers except ath11k_mac_op_unassign_vif_chanctx have that lock
acquired when calling ath11k_peer_find_by_addr. That lock is also not
transitively held by a path towards ath11k_mac_op_unassign_vif_chanctx.
The solution is to acquire the lock when calling
ath11k_peer_find_by_addr inside ath11k_mac_op_unassign_vif_chanctx.
I am currently working on a static analyser to detect missing locks and
this was a reported case. I manually verified the report by looking at
the code, but I do not have real hardware so this is compile tested
only.
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220314215253.92658-1-dossche.niels@gmail.com
Currently fw build id is printed during init as follows.
fw_version 0x250684a5 fw_build_timestamp 2021-07-13 10:57
fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
The string "QC_IMAGE_VERSION_STRING=" is removed from the log
to improve readability.
With this patch the fw build id is printed during init as follows.
fw_version 0x250684a5 fw_build_timestamp 2021-07-13 10:57
fw_build_id WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1646825065-7736-1-git-send-email-quic_haric@quicinc.com
Introduce new helper function for peer delete to reuse this logic
in all peer cleanup procedures. Found this in code review.
Also this change is applicable for all the platform.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1646024079-26391-1-git-send-email-quic_periyasa@quicinc.com
Host sets GTK related info to firmware before WoW is enabled, and
gets rekey replay_count and then disables GTK rekey when WoW quits.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-7-git-send-email-quic_cjhuang@quicinc.com
Support ARP and NS offload in WoW state.
Tested this way: put machine A with QCA6390 to WoW state,
ping/ping6 machine A from another machine B, check sniffer to see
any ARP response and Neighbour advertisement from machine A.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-6-git-send-email-quic_cjhuang@quicinc.com
This change is to purge rx pktlog when entering WoW and reap
the mon_status buffer to keep it empty. When leaving WoW, host
restarts the reap timer. In WoW state, it's not allowed to feed
into mon_status rings per firmware team's recommendation.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-5-git-send-email-quic_cjhuang@quicinc.com
Host needs to set hardware data filter before entering WoW to
let firmware drop needless broadcast/mulitcast frames to avoid
frequent wakeup. Host clears hardware data filter when leaving WoW.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-4-git-send-email-quic_cjhuang@quicinc.com
Implement net-detect feature by setting flag
WIPHY_WOWLAN_NET_DETECT if firmware supports this
feature. Driver sets the related PNO configuration
to firmware before entering WoW and firmware then
scans periodically and wakes up host if a specific
SSID is found.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-3-git-send-email-quic_cjhuang@quicinc.com
Implement basic WoW functionalities such as magic-packet, disconnect
and pattern. The logic is very similar to ath10k.
When WoW is configured, ath11k_core_suspend and ath11k_core_resume
are skipped as WoW configuration and hif suspend/resume are done in
ath11k_wow_op_suspend() and ath11k_wow_op_resume().
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-2-git-send-email-quic_cjhuang@quicinc.com
All work currently pending will be done first by calling destroy_workqueue,
so there is no need to flush it explicitly.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi (CGEL ZTE) <lv.ruyi@zte.com.cn>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220301013246.2052570-1-lv.ruyi@zte.com.cn
ath.git patches for v5.18. Major changes:
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
Target copies spectral report and CFR report through dbring to
host for further processing. This mechanism involves ring and
buffer management in the Host, FW, and uCode, where improper
tail pointer update issues are seen.
This dbring debug support help to debug such issues by tracking
head and tail pointer movement along with the timestamp at which
each buffer is received and replenished.
Provide a debugfs interface to enalbe/disable dbring debug
support and dump the dbring debug entries.
Also introduced a new hardware param to add dbring debugfs support
for few hardwares which are using dbings.
Usage:
echo <dbr_id> <val> > /sys/kernel/debug/ath11k/ipq8074_2/
mac0/enable_dbr_debug
dbr_id: 0 for spectral and 1 for CFR
val: 0 - disable, 1 - enable.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645366059-11798-1-git-send-email-quic_vnaralas@quicinc.com
Translate HE status to radiotap format. This uses HE radiotap
definitions from include/net/ieee80211_radiotap.h.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220217012112.31211-4-pradeepc@codeaurora.org
Add new bitmasks and macro definitions required for parsing HE
status tlvs. Decode HE status tlvs, which will used in dumping
ppdu stats as well as updating radiotap headers.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220217012112.31211-3-pradeepc@codeaurora.org
This allows us to pass HE rates down into the stack.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220217012112.31211-2-pradeepc@codeaurora.org
In some scenarios like firmware crashes during init time
and hardware gets restarted after qmi firmware ready event.
During restart, ath11k_core_qmi_firmware_ready() returns timeout.
But, this failure is not handled and ATH11K_FLAG_REGISTERED is set.
When hardware restart completed, firmware sends firmware ready event
again. Since ATH11K_FLAG_REGISTERED is already set, ath11k handles
this as core restart. Inits are not done because of previous timeout.
But ath11k_core_restart does deinit's which causes NULL pointer crash.
Fix this by handling failure from ath11k_core_qmi_firmware_ready().
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-00881-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645079195-13564-1-git-send-email-quic_seevalam@quicinc.com
REO2SW ring descriptor is currently allocated in cacheable memory.
While reaping reo ring entries on second trial after updating head
pointer, first entry is not invalidated before accessing it.
This results in host reaping and using cached descriptor which is
already overwritten in memory by DMA device (HW).
Since the contents of descriptor(buffer id, peer info and other information
bits) are outdated host throws errors like below while parsing corresponding
MSDU's and drops them.
[347712.048904] ath11k_pci 0004:01:00.0: msdu_done bit in attention is not set
[349173.355503] ath11k_pci 0004:01:00.0: frame rx with invalid buf_id 962
Move the try_again: label above ath11k_hal_srng_access_begin()
so that first entry will be invalidated and prefetched.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 6452f0a3d5 ("ath11k: allocate dst ring descriptors from cacheable memory")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645000354-32558-1-git-send-email-quic_ramess@quicinc.com
The rddm_size is needed by firmware while mhi enter RDDM state, add it
to support recovery when ath11k receive MHI_CB_EE_RDDM message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060012.32478-4-quic_wgong@quicinc.com
This is to fix m3 buffer reuse issue as m3_mem->size isn't set to
ZERO in free function, which leads invalid m3 downloading to
firmware and firmware crashed.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060012.32478-3-quic_wgong@quicinc.com
ath11k_qmi_free_target_mem_chunk() and ath11k_qmi_m3_free() is static
in qmi.c, they are needed for recovery, export them in a new function.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060012.32478-2-quic_wgong@quicinc.com
We add the fields for parsing extended ADDBA request/respond,
and new max 1K aggregation for limit ADDBA request/respond.
Adjust drivers to use the proper macro, IEEE80211_MAX_AMPDU_BUF ->
IEEE80211_MAX_AMPDU_BUF_HE.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20220214173004.b8b447ce95b7.I0ee2554c94e89abc7a752b0f7cc7fd79c273efea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
More than 20000 PPDU id jumping causing status ring and destination
ring processing not sync. The status ring is processed and the
destination ring is not processed. Since destination is not reaped for
so long, backpressure occurs at the destination ring.
To address this issue update the PPDU id with the latest PPDU, this
will allow the destination ring to be reaped and will prevent the
rings from getting out of sync.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220210064706.6171-1-quic_kathirve@quicinc.com
Radar detection fails in the secondary 80 MHz when the
the AP's primary 80 MHz is in non-DFS region in 160 MHz.
This is due to WMI channel flag WMI_CHAN_INFO_DFS_FREQ2 is not set
properly in case of the primary 80 MHz is in non-DFS region.
HALPHY detects the radar pulses in the secondary 80 MHz only when
WMI_CHAN_INFO_DFS_FREQ2 is set.
Fix this issue by setting WMI channel flag WMI_CHAN_INFO_DFS_FREQ2
based on the radar_enabled flag from the channel context.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644416019-820-2-git-send-email-quic_vnaralas@quicinc.com
Fix WARN_ON() from ath11k_mac_update_vif_chan() if vdev is not up.
Since change_chanctx can be called even before vdev_up from
ieee80211_start_ap->ieee80211_vif_use_channel->
ieee80211_recalc_radar_chanctx.
Do vdev stop followed by a vdev start in case of vdev is down.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644416019-820-1-git-send-email-quic_vnaralas@quicinc.com
The rate_idx which passed to ath11k_debugfs_sta_add_tx_stats() by
ath11k_dp_tx_update_txcompl() is not initialized, add initialization
for it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Fixes: 1b8bb94c06 ("ath11k: report tx bitrate for iw wlan station dump")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060816.423-1-quic_wgong@quicinc.com
The size of the status_driver_data field was not adjusted when
the is_valid_ack_signal field was added.
Since the size of struct ieee80211_tx_info is limited, replace
the is_valid_ack_signal field with a flags field, and adjust the
struct size accordingly.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.0ff363d4fa56.I45792c0187034a6d0e1c99a7db741996ef7caba3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These calls are used for debugging and will be required for WFA
certification tests.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220131031043.1295-1-alokad@codeaurora.org
Add debugfs interface "fw_dbglog_config" to configure firmware log level.
Configuration is done via WMI command WMI_DBGLOG_CFG_CMDID.
Command to configure,
echo "<dbglog_param> <values>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
where dbglog_param can be,
1) WMI_DEBUG_LOG_PARAM_LOG_LEVEL - configure log level for a given module
here, <values> = <0xaaaa00bb>, 'aaaa' - module id and 'bb' - loglevel
2) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE - enable debug log for a given vdev
here, <values> = vdev_id
3) WMI_DEBUG_LOG_PARAM_VDEV_DISABLE - disable debug log for a given vdev
except ERROR logs
here, <values> = vdev_id
4) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE_BITMAP - set vdev enable bitmap
here, <values> = vdev_enable_bitmap
5) WMI_DEBUG_LOG_PARAM_MOD_ENABLE_BITMAP - set a given log level to all the
modules specified in the module bitmap. Command to configure for this log param,
$ echo "5 <values> <module_id_index> <is_end>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
here,
<values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and
'bb' - loglevel
<module_id_index> = index of module bitmap. Max module id is 512.
So, module_id_index is 0-15.
<is_end> = to indicate if more configuration to follow.
6) WMI_DEBUG_LOG_PARAM_WOW_MOD_ENABLE_BITMAP - Wow mode specific logging enable.
Command to configure for this log param,
$ echo "6 <values> <module_id_index> <is_end>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
here,
<values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and
'bb' - loglevel
<module_id_index> = index of module bitmap. Max module id is 512.
So, module_id_index is 0-15.
<is_end> = to indicate if more configuration to follow.
Sample command usage,
To enable module WLAN_MODULE_WMI and log level ATH11K_FW_DBGLOG_VERBOSE,
echo "1 0x10001" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
To enable module bit map from 32 to 63 and log level ATH11K_FW_DBGLOG_VERBOSE,
echo "5 0xffffffff00000001 1 1" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1642405103-32302-1-git-send-email-quic_seevalam@quicinc.com
For the NL80211_REGDOM_SET_BY_USER hint from cfg80211, it set the new
alpha2 code to ath11k, then ath11k send WMI_SET_INIT_COUNTRY_CMDID to
firmware for all chips currently. When test with WCN6855/QCA6390 chips,
this WMI CMD leads firmware crash.
For AP based chips(ipq8074/qcn9074), WMI_SET_INIT_COUNTRY_CMDID is used
to send to firmware, for STATION based chips(WCN6855/QCA6390), it need to
use another WMI CMD WMI_SET_CURRENT_COUNTRY_CMDID.
Add flag current_cc_support in hardware parameters, it is used to
distinguish AP/STA platform. After that, the firmware will work
normal and the regulatory feature works well for QCA6390/WCN6855.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220119041355.32014-1-quic_wgong@quicinc.com
When station connect to AP of 6 GHz with 40 MHz bandwidth, the TX is
always stay 20 MHz, it is because the flag WMI_PEER_40MHZ is not set
while peer assoc. Add the flag if remote peer is 40 MHz bandwidth.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Fixes: c3a7d7eb4c ("ath11k: add 6 GHz params in peer assoc command")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220119034211.28622-1-quic_wgong@quicinc.com
There is an issue that WCN6855 tries to connect to an AP using
a hardware rate of 1Mb/s , even though the AP has announced
expected rates as [24, 36, 48, 54] in Probe Response frame.
The reason is that WCN6855 firmware clears hardware rate info
of management frames when vdev starts and uses 1Mb/s as default.
To solve it, reconfigure the rate after vdev is started.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220112025400.2222-1-quic_bqiang@quicinc.com
The "ret" vairable is not set at this point. It could be uninitialized
or zero. The correct thing to return is -ENODEV.
Fixes: 6ac04bdc5e ("ath11k: Use reserved host DDR addresses from DT for PCI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220111071445.GA11243@kili
Move the function below ath11k_dp_rx_mon_dest_process() and remove
the forward declaration.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220111032224.14093-2-quic_alokad@quicinc.com
RX PPDU statistics collection is missing when monitor mode co-exists
with other modes. This commit combines the processing of the destination
ring with the status ring to fix the issue.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220111032224.14093-1-quic_alokad@quicinc.com
Treewide cleanup and consolidation of MSI interrupt handling in
preparation for further changes in this area which are necessary to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space
-----BEGIN PGP SIGNATURE-----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=vKzd
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
LDPC is one the FEC type advertised in msdu_start info2 for HT packet
type. Hence, add hardware specific callback for fetching LDPC
support from msdu start and enable RX_ENC_FLAG_LDPC flag while passing
rx status to mac80211.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638294648-844-3-git-send-email-quic_ppranees@quicinc.com
When there is an error in peer create process from
ath11k_peer_find(), the code attempts to handle a fallback
for peer create. When this fallback fails, the driver returns
the fallback return code rather than actual error code
(-ENOENT). So refactor the fallback routine to return
the actual error code.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1640244819-21183-1-git-send-email-quic_periyasa@quicinc.com
Currently, ath11k_core_alloc() creates a single thread workqueue.
This workqueue is not detroyed during clean up when ath11k modules
are unloaded from the kernel and is left as it is.
If workqueue is not destroyed, it could lead to kernel
memory scarcity in a longer run. This could affect self and
other drivers workability as well.
Add destroy workqueue in ath11k_core_free().
Tested on: IPQ8074 WLAN.HK.2.4.0.1-01746-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1640231787-17408-1-git-send-email-quic_adisi@quicinc.com
The node pointer is returned by of_find_node_by_type()
or of_parse_phandle() with refcount incremented. Calling
of_node_put() to aovid the refcount leak.
Fixes: 6ac04bdc5e ("ath11k: Use reserved host DDR addresses from DT for PCI devices")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211221114003.335557-1-yangyingliang@huawei.com
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmHEgv4RHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt7jQf/W1J8lkaMw6mYnr+inmwKaP11VIk765Sf
4FXZl4xks5rs5zJOs61c/zInNIbu7QVsJzQLmM/bhTB1zoZMRo6ugXXrZ/LPMT1u
X0mul1rC+NLZLlgaimNXRZUXJ2tGUsYYhGoZLHbcILx7XF7/9WtE4h7tLviLdMYk
l42yjjP6s/I/zQHrLQdA9/puGl7g8CItbwaNZg6+PjgbS9NPGATrw9UZdOWjPcl4
JLMRHVgKtdlYL/U/IvsYg6o3Vbo0r+KEI2IMg5fOSpNwqbeQRIN4cZG4TDeRDqD/
k4/ZiFYlNdfVeWmZxHyqX6D3sroIquKglyah34fjzsJ2TbJC1zMvjw==
=VHFz
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
* tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits)
mt76: mt7921: fix a possible race enabling/disabling runtime-pm
wilc1000: Document enable-gpios and reset-gpios properties
wilc1000: Add reset/enable GPIO support to SPI driver
wilc1000: Convert static "chipid" variable to device-local variable
rtw89: 8852a: correct bit definition of dfs_en
rtw88: don't consider deep PS mode when transmitting packet
ath11k: Fix unexpected return buffer manager error for QCA6390
ath11k: add support of firmware logging for WCN6855
ath11k: Fix napi related hang
ath10k: replace strlcpy with strscpy
rtw88: support SAR via kernel common API
rtw88: 8822c: add ieee80211_ops::hw_scan
iwlwifi: mei: wait before mapping the shared area
iwlwifi: mei: clear the ownership when the driver goes down
iwlwifi: yoyo: fix issue with new DBGI_SRAM region read.
iwlwifi: fw: fix some scan kernel-doc
iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
iwlwifi: mvm: remove card state notification code
iwlwifi: mvm: drop too short packets silently
iwlwifi: mvm: fix AUX ROC removal
...
====================
Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d068ca2ae2 ("codel: split into multiple files") moved all
Qdisc-related code to codel_qdisc.h, move the include of pkt_sched.h
as well.
This is similar to the previous commit, although we don't care as
much about incremental builds after pkt_sched.h was touched itself
it is included by net/sch_generic.h which is modified ~20 times
a year.
This decreases the incremental build size after touching pkt_sched.h
from 1592 to 617 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since sock.h is modified relatively often (60 times in the last
12 months) it seems worthwhile to decrease the incremental build
work.
CoDel's header includes net/inet_ecn.h which in turn includes net/sock.h.
codel.h is itself included by mac80211 which is included by much of
the WiFi stack and drivers. Removing the net/inet_ecn.h include from
CoDel breaks the dependecy between WiFi and sock.h.
Commit d068ca2ae2 ("codel: split into multiple files") moved all
the code which actually needs ECN helpers out to net/codel_impl.h,
the include can be moved there as well.
This decreases the incremental build size after touching sock.h
from 4999 objects to 4051 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We are seeing below error on QCA6390:
...
[70211.671189] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70212.696154] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70213.092941] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
...
The reason is that, with commit 734223d784 ("ath11k: change return
buffer manager for QCA6390"), ath11k expects the return buffer manager
(RBM) field of descriptor configured as HAL_RX_BUF_RBM_SW1_BM when
parsing error frames from WBM2SW3_RELEASE ring. This is a wrong change
cause the RBM field is set as HAL_RX_BUF_RBM_SW3_BM.
The same issue also applies to REO2TCL ring though we have not got any
error reported.
Fix it by changing RBM from HAL_RX_BUF_RBM_SW1_BM to HAL_RX_BUF_RBM_SW3_BM
for these two rings.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: 734223d784 ("ath11k: change return buffer manager for QCA6390")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211222013536.582527-1-quic_bqiang@quicinc.com
Host enables WMI firmware logging feature via QMI message.
Host receives firmware logging messages on WMI_DIAG_EVENTID, then
sends logging messages to user space via event tracing infrastructure.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Cheng Wang <quic_chengwan@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211220121053.357087-1-quic_chengwan@quicinc.com
Similar to the same bug in ath10k, a napi disable w/out it being enabled
will hang forever. I believe I saw this while trying rmmod after driver
had some failure on startup. Fix it by keeping state on whether napi is
enabled or not.
And, remove un-used napi pointer in ath11k driver base struct.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20200903195254.29379-1-greearb@candelatech.com
The regdomain is self-managed type for ath11k, the regdomain info is
reported from firmware, it is not from wireless regdb. Firmware fetch
the regdomain info from board data file before. Currently most of the
regdomain info has moved to another file regdb.bin from board data
file for some chips such as QCA6390 and WCN6855, so the regdomain info
left in board data file is not enough to support the feature which need
more regdomain info.
After download regdb.bin, firmware will fetch the regdomain info from
regdb.bin instead of board data file and report to ath11k. If it does
not have the file regdb.bin, it also can initialize wlan success and
firmware then fetch regdomain info from board data file.
Add download the regdb.bin before download board data for some specific
chip which support supports_regdb in hardware parameters.
download regdb.bin log:
[430082.334162] ath11k_pci 0000:05:00.0: chip_id 0x2 chip_family 0xb board_id 0x106 soc_id 0x400c0200
[430082.334169] ath11k_pci 0000:05:00.0: fw_version 0x110c8b4c fw_build_timestamp 2021-10-25 07:41 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02892-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
[430082.334414] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/regdb.bin size 24310
output of "iw reg get"
global
country US: DFS-FCC
(2402 - 2472 @ 40), (N/A, 30), (N/A)
(5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
(5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
(5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
(5735 - 5835 @ 80), (N/A, 30), (N/A)
(57240 - 63720 @ 2160), (N/A, 40), (N/A)
phy#0 (self-managed)
country US: DFS-FCC
(2402 - 2472 @ 40), (6, 30), (N/A)
(5170 - 5250 @ 80), (N/A, 24), (N/A), AUTO-BW
(5250 - 5330 @ 80), (N/A, 24), (0 ms), DFS, AUTO-BW
(5490 - 5730 @ 160), (N/A, 24), (0 ms), DFS, AUTO-BW
(5735 - 5895 @ 160), (N/A, 30), (N/A), AUTO-BW
(5945 - 7125 @ 160), (N/A, 24), (N/A), NO-OUTDOOR, AUTO-BW
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211220062355.17021-1-quic_wgong@quicinc.com
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath11k will check the capability, and if it is enabled then
ath11k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath11k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware and also notifies cfg80211.
This only enable rfkill feature for QCA6390, rfkill_pin is all initialized to 0
for other chips in ath11k_hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211217102334.14907-1-quic_wgong@quicinc.com
HTT_T2H_MSG_TYPE_PPDU_STATS_IND is a message which include the ppdu
info, currently it is not report from firmware for ath11k, then the
tx bitrate of "iw wlan0 station dump" always show an invalid value
"tx bitrate: 6.0 MBit/s".
To address the issue, this is to parse the info of tx complete report
from firmware and indicate the tx rate to mac80211.
After that, "iw wlan0 station dump" show the correct tx bit rate such
as:
tx bitrate: 78.0 MBit/s MCS 12
tx bitrate: 144.4 MBit/s VHT-MCS 7 short GI VHT-NSS 2
tx bitrate: 286.7 MBit/s HE-MCS 11 HE-NSS 2 HE-GI 0 HE-DCM 0
tx bitrate: 1921.5 MBit/s 160MHz HE-MCS 9 HE-NSS 2 HE-GI 0 HE-DCM 0
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211217093722.5739-1-quic_wgong@quicinc.com
IEEE80211_HW_USES_RSS is set in ath11k, then the device uses RSS and
thus requires parallel RX which implies using per-CPU station statistics
in sta_get_last_rx_stats() of mac80211. Currently signal is only set in
ath11k_mgmt_rx_event(), and not set for RX data packet, then it show
signal as 0 for iw command easily.
Change to get signal from firmware and report to mac80211.
For QCA6390 and WCN6855, the rssi value is already in dbm unit, so
don't need to convert it again.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211216070535.31732-1-quic_wgong@quicinc.com
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmG8i3cRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZumyAf7BlhO1TUuwhhs9y6fi6KLa/pEOmkx2SRf
9AuEfxxrLPhlzh29Dz4Bn8B+KBG6HFQ1FngSwIAVjLL5pX/1ARBMx9B2TDf9p/Sb
UgkE6WOX29s7LXuC2lDnBnvnKbf5/rdLmZPZCFCv/iKaGAJAYYXYSQjtj5/Fmdkc
PhQNgALWG9a02bfSLk1MlF1lCqt0hsKFQkza29jTa9CKcWYZFK3sTl1spbHAN5yQ
YJMecy+fSxCSuJPZB3elG5os69sz3WGoFY/AYCWoUODNZo18Z4kiAXwurPDIM+GW
3e/lzXe29V1TB36haNe9/C5F2uwoYWGSoWwHcZ62lLpNhJ649wJDbw==
=4wFO
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
* tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (129 commits)
wcn36xx: Implement beacon filtering
wcn36xx: Fix physical location of beacon filter comment
wcn36xx: Fix beacon filter structure definitions
ath11k: Use reserved host DDR addresses from DT for PCI devices
dt: bindings: add new DT entry for ath11k PCI device support
wilc1000: Improve WILC TX performance when power_save is off
wl1251: specify max. IE length
rsi: fix array out of bound
wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"
wilc1000: Rename tx task from "K_TXQ_TASK" to NETDEV-tx
wilc1000: Rename irq handler from "WILC_IRQ" to netdev name
wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi"
wilc1000: Fix spurious "FW not responding" error
wilc1000: Remove misleading USE_SPI_DMA macro
wilc1000: Fix missing newline in error message
wilc1000: Fix copy-and-paste typo in wilc_set_mac_address
rtw89: coex: Update COEX to 5.5.8
rtw89: coex: Cancel PS leaving while C2H comes
rtw89: coex: Update BT counters while receiving report
rtw89: coex: Define LPS state for BTC using
...
====================
Link: https://lore.kernel.org/r/20211217130952.34887C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Host DDR memory (contiguous 45 MB in mode-0 or 15 MB in mode-2)
is reserved through DT entries for firmware usage. Send the base
address from DT entries.
If DT entry is available, PCI device will work with
fixed_mem_region else host allocates multiple segments.
IPQ8074 on HK10 board supports multiple PCI devices.
IPQ8074 + QCN9074 is tested with this patch.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638789319-2950-2-git-send-email-akolli@codeaurora.org
In mode-2 QCN9074 firmware uses 15MB of host memory and firmware
request 1MB size segements in QMI, whereas in mode-0 firmware
uses 45MB of host memory and each segment is of 2MB size.
In mode-2 firmware operates with reduced number of vdevs and peers.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209104351.9811-3-kvalo@kernel.org
The next patch changes TARGET_NUM_VDEVS to be dynamic and need access to ab.
Add ab separately to keep the next patch simple.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209104351.9811-2-kvalo@kernel.org
In ath11k_mac_op_hw_scan(), the return value of kzalloc() is directly
used in memcpy(), which may lead to a NULL pointer dereference on
failure of kzalloc().
Fix this bug by adding a check of arg.extraie.ptr.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_ATH11K=m show no new warnings, and our static
analyzer no longer warns about this code.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211202155348.71315-1-zhou1615@umn.edu
Set DTIM policy to DTIM stick mode, so station follows AP DTIM
interval rather than listen interval which is set in peer assoc cmd.
DTIM stick mode is more preferred per firmware team request.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638948694-15582-1-git-send-email-quic_cjhuang@quicinc.com
The driver reports NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR capability
to upper layer based on the service bit firmware reported. Driver
sets the spoofed flag in scan_ctrl_flag to firmware if upper layer
has enabled this feature in scan request.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638948007-9609-1-git-send-email-quic_cjhuang@quicinc.com
For whatever reason, some devices like QCA6390, WCN6855 using ath11k
are not in M3 state during PM resume, but still functional. The
mhi_pm_resume should then not fail in those cases, and let the higher
level device specific stack continue resuming process.
Add an API mhi_pm_resume_force(), to force resuming irrespective of the
current MHI state. This fixes a regression with non functional ath11k WiFi
after suspend/resume cycle on some machines.
Bug report: https://bugzilla.kernel.org/show_bug.cgi?id=214179
Link: https://lore.kernel.org/regressions/871r5p0x2u.fsf@codeaurora.org/
Fixes: 020d3b26c0 ("bus: mhi: Early MHI resume failure in non M3 state")
Cc: stable@vger.kernel.org #5.13
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Reported-by: Pengyu Ma <mapengyu@gmail.com>
Tested-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[mani: Switched to API, added bug report, reported-by tags and CCed stable]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20211209131633.4168-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unnamed struct sucks and is in the way of further cleanups. Stick the
PCI related MSI data into a real data structure and cleanup all users.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211206210224.374863119@linutronix.de
Currently there is no validation on the spectral/CFR report
over the db ring buffers from the hardware. Improper/incomplete
DMA by the target can result in invalid data received by host.
Due to this we may populate incorrect data to user space.
This buffer validation support fix this issues by filling some
magic value in the buffer during buffer replenish and check for
the magic value in the buffer received by the target. If host
detect magic value in the received buffer it will drop the buffer.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1637312901-10279-2-git-send-email-quic_vnaralas@quicinc.com
In full monitor mode, monitor destination ring is read before monitor
status ring. mon_dst_ring has ppdu id, reap till the end of PPDU. Add
all the MPDUs to list. Start processing the status ring, if PPDU id in
status ring is lagging behind, reap the status ring, once the PPDU ID
matches, deliver the MSDU to upper layer. If status PPDU id leading,
reap the mon_dst_ring.
The advantage with full monitor mode is hardware has status buffers
available for all the MPDUs in mon_dst_ring, which makes it possible
to deliver more frames to be seen on sniffer.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-4-git-send-email-akolli@codeaurora.org
In full monitor mode, monitor destination ring is read in
software monitor ring descriptor format instead of
reo_entrance_ring format. Add new sw_mon_ring descriptor.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-3-git-send-email-akolli@codeaurora.org
A new hw_param full_monitor_mode is added to enable full
monitor support for QCN9074.
HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE cmd is sent to FW
to enable the full monitor mode.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-2-git-send-email-akolli@codeaurora.org
Currently mac80211 will send 3 scan request for each scan of WCN6855,
they are 2.4 GHz/5 GHz/6 GHz band scan. Firmware of WCN6855 will
cache the RNR IE(Reduced Neighbor Report element) which exist in the
beacon of 2.4 GHz/5 GHz of the AP which is co-located with 6 GHz,
and then use the cache to scan in 6 GHz band scan if the 6 GHz scan
is in the same scan with the 2.4 GHz/5 GHz band, this will helpful to
search more AP of 6 GHz. Also it will decrease the time cost of scan
because firmware will use dual-band scan for the 2.4 GHz/5 GHz, it
means the 2.4 GHz and 5 GHz scans are doing simultaneously.
Set the flag IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS for WCN6855 since
it supports 2.4 GHz/5 GHz/6 GHz and it is single pdev which means
all the 2.4 GHz/5 GHz/6 GHz exist in the same wiphy/ieee80211_hw.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129101309.2931-1-quic_wgong@quicinc.com
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org
In ath11k, tx of management packet is doing in a work queue. Sometimes
the workqueue does not finish tx immediately, then it lead after the next
step of vdev delete finished, it start to send the management packet to
firmware and lead firmware crash.
ieee80211_set_disassoc() have logic of ieee80211_flush_queues() after
it send_deauth_disassoc() to ath11k, its purpose is make sure the
deauth was actually sent, so it need to change ath11k to match the
purpose of mac80211.
To address these issue wait for tx mgmt as well as tx data packets.
dmesg log of connect/disconnect to AP:
[ 307.522226] wls1: authenticate with 62:66:e4:e9:6a:a9
[ 307.586565] wls1: send auth to 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.586581] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.586922] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.590179] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.590181] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.598699] wls1: authenticated
[ 307.599483] wls1: associate with 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.599506] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.599519] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.603059] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.603063] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.637105] wls1: associated
[ 317.365239] wls1: deauthenticating from 62:66:e4:e9:6a:a9 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 317.368104] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 317.372622] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 317.378320] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 317.378330] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 317.378359] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421066] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421427] ath11k_pci 0000:05:00.0: mac remove interface (vdev 0)
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211202063705.14321-1-quic_wgong@quicinc.com
Add handler for WMI_11D_NEW_COUNTRY_EVENTID, WMI_11D_SCAN_START_CMDID,
WMI_11D_SCAN_STOP_CMDID.
After vdev create for STATION, send WMI_11D_SCAN_START_CMDID to firmware
and wait firmware complete it, the scan from mac80211 also need to wait
the 11d scan finished, and send WMI_11D_SCAN_STOP_CMDID to firmware
before vdev delete for STATION.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-4-quic_wgong@quicinc.com
Add handler to send WMI_SET_CURRENT_COUNTRY_CMDID to firmware which
is used for QCA6390 and WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-3-quic_wgong@quicinc.com
Currently there are about 60 channels for 6 GHz, then the size of
chan_list in struct scan_req_params which is 40 is not enough to
fill all the channel list of 6 GHz.
Use dynamic memory to save the channel list of scan.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129110939.15711-1-quic_wgong@quicinc.com
bdf_type for caldata in QMI_WLANFW_BDF_DOWNLOAD_REQ_V01 is wrongly
sent as 1. But, expected bdf_type value for caldata and EEPROM is 2 and 3
respectively. It leads to firmware crash. Fix ath11k_qmi_file_type enum
values.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Fixes: 336e7b53c8 ("ath11k: clean up BDF download functions")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638182754-18408-1-git-send-email-quic_seevalam@quicinc.com
Ath11k fails to probe WCN6855 hw2.1 chip:
[ 6.983821] ath11k_pci 0000:06:00.0: enabling device (0000 -> 0002)
[ 6.983841] ath11k_pci 0000:06:00.0: Unsupported WCN6855 SOC hardware version: 18 17
This is caused by the wrong bit mask setting of hardware major version:
for QCA6390/QCN6855, it should be BIT8-11, not BIT8-16, so change the
definition to GENMASK(11, 8).
Also, add a separate entry for WCN6855 hw2.1 in ath11k_hw_params.
Please note that currently WCN6855 hw2.1 shares the same firmwares
as hw2.0, so users of this chip need to create a symlink as below:
ln -s hw2.0 hw2.1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: 18ac1665e7 ("ath11k: pci: check TCSR_SOC_HW_VERSION")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129025613.21594-1-quic_bqiang@quicinc.com
Currently 'ar' reference is not added in skb_cb during
WMI mgmt tx. Though this is generally not used during tx completion
callbacks, on interface removal the remaining idr cleanup callback
uses the ar ptr from skb_cb from mgmt txmgmt_idr. Hence
fill them during tx call for proper usage.
Also free the skb which is missing currently in these
callbacks.
Crash_info:
[19282.489476] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[19282.489515] pgd = 91eb8000
[19282.496702] [00000000] *pgd=00000000
[19282.502524] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[19282.783728] PC is at ath11k_mac_vif_txmgmt_idr_remove+0x28/0xd8 [ath11k]
[19282.789170] LR is at idr_for_each+0xa0/0xc8
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637832614-13831-1-git-send-email-quic_srirrama@quicinc.com
CE interrupt configuration uses host ce parameters to assign/free
interrupts. Use host ce parameters to enable/disable interrupts.
This patch fixes below BUG,
BUG: KASAN: global-out-of-bounds in 0xffffffbffdfb035c at addr
ffffffbffde6eeac
Read of size 4 by task kworker/u8:2/132
Address belongs to variable ath11k_core_qmi_firmware_ready+0x1b0/0x5bc [ath11k]
OOB is due to ath11k_ahb_ce_irqs_enable() iterates ce_count(which is 12)
times and accessing 12th element in target_ce_config
(which has only 11 elements) from ath11k_ahb_ce_irq_enable().
With this change host ce configs are used to enable/disable interrupts.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00471-QCAHKSWPL_SILICONZ-1
Fixes: 967c1d1131 ("ath11k: move target ce configs to hw_params")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249558-12793-1-git-send-email-akolli@codeaurora.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_startat() so memset() doesn't get confused about writing
beyond the destination member that is intended to be the starting point
of zeroing through the end of the struct. Additionally split up a later
field-spanning memset() so that memset() can reason about the size.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118202416.1286046-1-keescook@chromium.org
This reverts commit 46e46db313. Mark reported
that it breaks QCA6390 hw2.0 on Dell XPS 13 9310:
[ 5.537034] ath11k_pci 0000:72:00.0: chip_id 0x0 chip_family 0xb board_id 0xff soc_id 0xffffffff
[ 5.537038] ath11k_pci 0000:72:00.0: fw_version 0x101c06cc fw_build_timestamp 2020-06-24 19:50 fw_build_id
[ 5.537236] ath11k_pci 0000:72:00.0: failed to fetch board data for bus=pci,qmi-chip-id=0,qmi-board-id=255,variant=DE_1901 from ath11k/QCA6390/hw2.0/board-2.bin
[ 5.537255] ath11k_pci 0000:72:00.0: failed to fetch board-2.bin or board.bin from QCA6390/hw2.0
[ 5.537257] ath11k_pci 0000:72:00.0: qmi failed to fetch board file: -2
[ 5.537258] ath11k_pci 0000:72:00.0: failed to load board data file: -2
So we need to back to the drawing board and implement it so that backwards
compatiblity is not broken.
Reported-by: Mark Herbert <mark.herbert42@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211124094316.9096-1-kvalo@codeaurora.org
In HE monitor capture, HAL_TLV_STATUS_PPDU_DONE is received
on processing multiple skb. Do not clear the ppdu_info
till the HAL_TLV_STATUS_PPDU_DONE is received.
This fixes below warning and packet drops in monitor mode.
"Rate marked as an HE rate but data is invalid: MCS: 6, NSS: 0"
WARNING: at
PC is at ieee80211_rx_napi+0x624/0x840 [mac80211]
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01693-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249433-10316-1-git-send-email-akolli@codeaurora.org
This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118100033.8384-1-quic_wgong@quicinc.com
The ath11k driver currently sends vdev down to the firmware before
updating the channel context, which is followed by a vdev restart
command.
Sending vdev down is not required before sending a vdev restart,
because the firmware internally does vdev down when ath11k sends
a vdev restart command.
Firmware will happen crash while channel switch without this change.
Hence skip the vdev down command sending when updating the channel
context and then fix the firmware crash issue.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095901.8271-1-quic_wgong@quicinc.com
The pdev id is set to 0 for single pdev configured hardware, the real
pdev id is not 0 in firmware, for example, its pdev id is 1 for 5G/6G
phy and 2 for 2G band phy. For HTT_H2T_MSG_TYPE_EXT_STATS_CFG message,
firmware parse the pdev_mask to its pdev id, ath11k set it to 0 for
single pdev, it is not correct, need set it with the real pdev id of
firmware.
Save the real pdev id report by firmware and set it correctly.
Below commands run success with this patch:
cat /sys/kernel/debug/ieee80211/phy0/ath11k/htt_stats
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wls1/stations/00\:03\:7f\:75\:59\:85/htt_peer_stats
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095700.8149-1-quic_wgong@quicinc.com
When connected to 6G mode AP, it does not have VHT/HT capabilities,
so the NSS is not set, then it is 1 by default.
This patch is to calculate the NSS with supported HE-MCS and NSS set
of HE capabilities.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01280-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095453.8030-1-quic_wgong@quicinc.com
Some firmware versions for WCN6855 report the default regdomain with
alpha code "na" by default when load as a world wide regdomain, ath11k
should treat it as a world wide alpha code.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118094848.7776-1-quic_wgong@quicinc.com
With VT-d disabled on Intel platform, ath11k gets only one MSI
vector. In that case, ath11k does not free IRQ when doing suspend,
hence the kernel has to migrate it to CPU0 (if it was affine to
other CPUs) and allocates a new MSI vector. However, ath11k has
no chance to reconfig it to HW srngs during this phase, thus
ath11k fails to resume.
This issue can be fixed by setting IRQ affinity to CPU0 before
request_irq is called. With such affinity, migration will not
happen and thus the vector keeps unchanged during suspend/resume.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041732.5323-1-bqiang@codeaurora.org
Current code enables ASPM by default, it allows MHI to enter M2 state.
In case of one MSI vector, system hang is observed if ath11k does MHI
register reading in this state. The issue was reported on Dell XPS 13
9310 but is seen also on XPS 15 and XPS 17 laptops.
The workaround here is to prevent MHI from entering M2 state, this can
be done by disabling ASPM if only one MSI vector is used. When using 32
vectors ASPM is enabled as before.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041722.5271-1-bqiang@codeaurora.org
On some platforms it's not possible to allocate 32 MSI vectors for various
reasons, be it kernel configuration, VT-d disabled, buggy BIOS etc. So
ath11k was not able to use QCA6390 PCI devices on those platforms. Add
support for one MSI vector to solve that.
In case of one MSI vector, interrupt migration needs to be disabled. This
is because when interrupt migration happens, the msi_data may change.
However, msi_data is already programmed to rings during initial phase and
ath11k has no way to know that msi_data is changed during run time and
reprogram again.
In case of one MSI vector, MHI subsystem should not use IRQF_NO_SUSPEND
as QCA6390 doesn't set this flag too. Ath11k doesn't need to leave
IRQ enabled in suspend state.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041714.5219-1-bqiang@codeaurora.org
This is to prepare for one MSI vector support. IRQ enable and disable
of CE and DP are done only in case of multiple MSI vectors.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041705.5167-1-bqiang@codeaurora.org
Like ATH11K_PCI_IRQ_CE0_OFFSET, define ATH11K_PCI_IRQ_DP_OFFSET for
DP to save the IRQ instead of base_vector from MSI config.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041655.5112-1-bqiang@codeaurora.org
This change adds two flags to indicate whether IRQ handler for CE
and DP can be called. This is because in one MSI vector case,
interrupt is not disabled in hif_stop and hif_irq_disable. Otherwise,
MHI interrupt is disabled too.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041646.5060-1-bqiang@codeaurora.org
The reservation mode of interrupts in kernel assigns a dummy vector
when the interrupt is allocated and assigns a real vector when the
request_irq is called. The reservation mode helps to ease vector
pressure when devices with a large amount of queues/interrupts
are initialized, but only a minimal subset of those queues/interrupts
is actually used.
So on reservation mode, the msi_data may change after request_irq
is called, so ath11k reads msi_data again after request_irq is called,
and then the correct msi_data is programmed into QCA6390 hardware
components. Without this change, spurious interrupt occurs in case of
one MSI vector. When VT-d in BIOS is enabled and ath11k can get 32 MSI
vectors, ath11k always get the same msi_data before and after request_irq,
that's why this change is only required when one MSI vector is to be
supported.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041636.5008-1-bqiang@codeaurora.org
Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
QCN9074 when doing 'rmmod ath11k_pci':
Kernel panic - not syncing: dev_wake != 0
CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
Hardware name: Generic DT based system
[<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
[<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
[<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
[<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
[<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
[<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
[<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
[<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
[<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
[<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
[<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
[<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)
Hence, disable wakeup/release mhi using hw_param for other hardwares.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1
Fixes: a05bd85133 ("ath11k: read and write registers below unwindowed address")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com
The ath11k driver is caching the information about RSN/WPA IE in the
configured beacon template. The cached information is used during
associations to figure out whether 4-way PKT/2-way GTK peer flags need to
be set or not.
But the code never cleared the state when no such IE was found. This can
for example happen when moving from an WPA/RSN to an open setup. The
(seemingly connected) peer was then not able to communicate over the
link because the firmware assumed a different (encryption enabled) state
for the peer.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 01e34233c6 ("ath11k: fix wmi peer flags in peer assoc command")
Cc: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-2-sven@narfation.org
DISABLE_KEY sets the key_len to 0, firmware will not delete the keys if
key_len is 0. Changing from security mode to open mode will cause mcast
to be still encrypted without vdev restart.
Set the proper key_len for DISABLE_KEY cmd to clear the keys in
firmware.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-1-sven@narfation.org
Whenever the MAC detects a color collision, or any of
its associated stations detects one, the firmware will
send out an event. Add the code to parse and handle
this event and pass the data up to mac80211.
The firmware does not provide an offload feature such
as the one used for CSA. The color change process is
hence triggered via the beacon offload tx completion
events sent out by firmware.
BSS color feature is enabled depending on service flag
advertised by firmware, based on which color change
functionality is invoked.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00680-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635178254-17732-1-git-send-email-quic_ramess@quicinc.com
Currently ath11k only support string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for ahb bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCIe bus chip in
board-2.bin. For WCN6855, it is not enough to distinguish all different
chips.
This is to add a new string type which include bus, chip id, board id,
vendor, device, subsystem-vendor and subsystem-device for WCN6855.
ath11k will first load board-2.bin and search in it for the board data
with the above parameters, if matched one board data, then download it
to firmware, if not matched any one, then ath11k will download the file
board.bin to firmware.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111065340.20187-1-quic_wgong@quicinc.com
Currently many functions do not follow this guidance when
qmi_send_request() fails, therefore add missing
qmi_txn_cancel() in the qmi_send_request() error path.
Also remove initialization on 'struct qmi_txn'
since qmi_tx_init() performs all necessary initialization.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635857558-21733-1-git-send-email-akolli@codeaurora.org
The DMA buffers of dbring which is used for spectral/cfr
starts at certain offset from original kmalloc() returned buffer.
This is not cache line aligned.
And also driver tries to access the data that is immediately before
this offset address (i.e. buff->paddr) after doing dma map.
This will cause cache line sharing issues and data corruption,
if CPU happen to write back cache after HW has dma'ed the data.
Fix this by mapping a cache line aligned buffer to dma.
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635831693-15962-1-git-send-email-quic_ramess@quicinc.com
Firmware credit flow control is enabled for WMI control services,
which expects available tokens should be acquired before sending a
command to the target. Also the token gets released when firmware
receives the command.
This credit-based flow limits driver to send WMI command only
when the token available which is causing WMI commands to timeout and
return -EAGAIN, whereas firmware has enough capability to process the
WMI command. To fix this Tx starvation issue, introduce the ability to
disable the credit flow for the WMI path.
The driver sends WMI configuration for disabling credit flow to firmware
by two ways.
1. By using a global flag
(HTC_MSG_SETUP_COMPLETE_EX_ID msg type flags)
2. By using a local flag
(ATH11K_HTC_CONN_FLAGS_DISABLE_CREDIT_FLOW_CTRL = 1 << 3)
Ath11k uses both these configurations to disable credit flow for the
WMI path completely.
Also added a hw_param member for credit flow control by which we can
enable or disable it based on per-target basis. Currently we are disabling
credit flow for IPQ8074, IPQ6018, and QCN9074 as recommended by firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Co-developed-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635156494-20059-1-git-send-email-quic_ppranees@quicinc.com
Some ETSI countries have a small overlap in the wireless-regdb with an ETSI
channel (5590-5650). A good example is Australia:
country AU: DFS-ETSI
(2400 - 2483.5 @ 40), (36)
(5150 - 5250 @ 80), (23), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (20), NO-OUTDOOR, AUTO-BW, DFS
(5470 - 5600 @ 80), (27), DFS
(5650 - 5730 @ 80), (27), DFS
(5730 - 5850 @ 80), (36)
(57000 - 66000 @ 2160), (43), NO-OUTDOOR
If the firmware (or the BDF) is shipped with these rules then there is only
a 10 MHz overlap with the weather radar:
* below: 5470 - 5590
* weather radar: 5590 - 5600
* above: (none for the rule "5470 - 5600 @ 80")
There are several wrong assumption in the ath11k code:
* there is always a valid range below the weather radar
(actually: there could be no range below the weather radar range OR range
could be smaller than 20 MHz)
* intersected range in the weather radar range is valid
(actually: the range could be smaller than 20 MHz)
* range above weather radar is either empty or valid
(actually: the range could be smaller than 20 MHz)
These wrong assumption will lead in this example to a rule
(5590 - 5600 @ 20), (N/A, 27), (600000 ms), DFS, AUTO-BW
which is invalid according to is_valid_reg_rule() because the freq_diff is
only 10 MHz but the max_bandwidth is set to 20 MHz. Which results in a
rejection like:
WARNING: at backports-20210222_001-4.4.60-b157d2276/net/wireless/reg.c:3984
[...]
Call trace:
[<ffffffbffc3d2e50>] reg_get_max_bandwidth+0x300/0x3a8 [cfg80211]
[<ffffffbffc3d3d0c>] regulatory_set_wiphy_regd_sync+0x3c/0x98 [cfg80211]
[<ffffffbffc651598>] ath11k_regd_update+0x1a8/0x210 [ath11k]
[<ffffffbffc652108>] ath11k_regd_update_work+0x18/0x20 [ath11k]
[<ffffffc0000a93e0>] process_one_work+0x1f8/0x340
[<ffffffc0000a9784>] worker_thread+0x25c/0x448
[<ffffffc0000aedc8>] kthread+0xd0/0xd8
[<ffffffc000085550>] ret_from_fork+0x10/0x40
ath11k c000000.wifi: failed to perform regd update : -22
Invalid regulatory domain detected
To avoid this, the algorithm has to be changed slightly. Instead of
splitting a rule which overlaps with the weather radar range into 3 pieces
and accepting the first two parts blindly, it must actually be checked for
each piece whether it is a valid range. And only if it is valid, add it to
the output array.
When these checks are in place, the processed rules for AU would end up as
country AU: DFS-ETSI
(2400 - 2483 @ 40), (N/A, 36), (N/A)
(5150 - 5250 @ 80), (6, 23), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (6, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5590 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5650 - 5730 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5730 - 5850 @ 80), (6, 36), (N/A), AUTO-BW
and will be accepted by the wireless regulatory code.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112153116.1214421-1-sven@narfation.org
There is a race condition whereby the tx completion handler can be invoked
before the 'num_pending_mgmt_tx" count is incremented. If that occurs, we
could get warning trace indicating that 'num_pending_mgmt_tx' is 0 (because
it was not yet incremented). Ideally, this trace should be seen only if
mgmt tx has not happened but tx completion is received, and it is not
expected in this race condition.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635168282-8845-1-git-send-email-quic_ppranees@quicinc.com
Set proper values for max_regpower, max_power, max_antenna_gain as it
is because firmware will convert power values to 0.5dbm steps by
multiplying it with 2.
If txpower is not set, it will lead to cca stuck resulting in latency
issues for QCN9074.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164229-22880-1-git-send-email-quic_ppranees@quicinc.com
In radio tap header, BAD FCS flag is not updated properly because
driver failed to update FCS_ERR flag in monitor mode.
In rx_desc, FCS_ERR information is available in rx_attention
structure and presence of this field indicates corresponding frame
failed FCS check.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164060-18423-1-git-send-email-quic_ppranees@quicinc.com
When station connect to AP, the wmi command sequence is:
peer_create->vdev_start->vdev_up
and sequence of station disconnect fo AP is:
peer_delete->vdev_down->vdev_stop
The sequence of disconnect is not opposite of connect, it caused firmware
crash when it handle wmi vdev stop cmd when the AP is support TWT of
802.11 ax, because firmware need access the bss peer for vdev stop cmd.
[ 390.438564] ath11k_pci 0000:05:00.0: wmi cmd send 0x6001 ret 0
[ 390.438567] ath11k_pci 0000:05:00.0: WMI peer create vdev_id 0 peer_addr c4:04:15:3b:e0:39
[ 390.472724] ath11k_pci 0000:05:00.0: mac vdev 0 start center_freq 2437 phymode 11ax-he20-2g
[ 390.472731] ath11k_pci 0000:05:00.0: wmi cmd send 0x5003 ret 0
[ 390.560849] ath11k_pci 0000:05:00.0: wmi cmd send 0x5005 ret 0
[ 390.560850] ath11k_pci 0000:05:00.0: WMI mgmt vdev up id 0x0 assoc id 1 bssid c4:04:15:3b:e0:39
[ 399.432896] ath11k_pci 0000:05:00.0: WMI peer delete vdev_id 0 peer_addr c4:04:15:3b:e0:39
[ 399.432902] ath11k_pci 0000:05:00.0: wmi cmd send 0x6002 ret 0
[ 399.441380] ath11k_pci 0000:05:00.0: wmi cmd send 0x5007 ret 0
[ 399.441381] ath11k_pci 0000:05:00.0: WMI vdev down id 0x0
[ 399.454681] ath11k_pci 0000:05:00.0: wmi cmd send 0x5006 ret 0
[ 399.454682] ath11k_pci 0000:05:00.0: WMI vdev stop id 0x0
The opposite sequence of disconnect should be:
vdev_down->vdev_stop->peer_delete
This patch change the sequence of disconnect for station as above
opposite sequence for QCA6390, firmware not crash again with this patch.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027093825.12167-1-quic_wgong@quicinc.com
parameter of msecs_to_jiffies should be (3 * 1000) instead of (3 * HZ)
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026032014.27010-1-quic_wgong@quicinc.com
Currently in ath11k_mac_op_sta_statistics() there is the following
logic:
if (!arsta->txrate.legacy && !arsta->txrate.nss)
return;
Unfortunately if this condition is true then the function returns without
setting parameters that follow the txrate. To address this issue remove the
return and instead invert the logic to set the txrate logic if
(arsta->txrate.legacy || arsta->txrate.nss).
The same was done also in ath10k in commit 1cd6ba8ae3 ("ath10k: remove return
for NL80211_STA_INFO_TX_BITRATE").
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011084957.31024-1-wgong@codeaurora.org
When NSS ratio enabled reported by firmware, SUPPORTS_VHT_EXT_NSS_BW
is set in ath11k, meanwhile IEEE80211_VHT_EXT_NSS_BW_CAPABLE also
need to be set, otherwise it is invalid because spec in IEEE Std
802.11™‐2020 as below.
Table 9-273-Supported VHT-MCS and NSS Set subfields, it has subfield
VHT Extended NSS BW Capable, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS
BW Support subfield of the VHT Capabilities Information field.
dmesg have a message without this patch:
ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag
It means mac80211 will set IEEE80211_VHT_EXT_NSS_BW_CAPABLE if ath11k not
set it in ieee80211_register_hw(). So it is better to set it in ath11k.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211013073704.15888-1-wgong@codeaurora.org
Avoid unnecessary idr_find calls before the idr_remove calls. Because
idr_remove gives the valid ptr if id is valid otherwise return NULL ptr.
So removed the idr_find before idr_remove in tx completion path. Also no
need to disable the bottom half preempt if it is already in the
bottom half context, so modify the spin_lock_bh to spin_lock in the
data tx completion path.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-13-git-send-email-ppranees@codeaurora.org
Add branch prediction in dp_tx code path in tx and tx completion handlers.
Also in ath11k_dp_tx_complete_msdu , the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-12-git-send-email-ppranees@codeaurora.org
Currently while loop is used to find the tx completion ring number and
it is not required since the tx ring mask and the group id can be combined
to directly fetch the ring number. Hence remove the while loop
and directly get the ring number from tx mask and group id.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-11-git-send-email-ppranees@codeaurora.org
Replace use of mod operator with a manual wrap around
to avoid additional cost of using mod operation.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-10-git-send-email-ppranees@codeaurora.org
Similar to REO destination ring, also allocate HAL_WBM2SW_RELEASE
from cacheable memory so that descriptors could be prefetched during
tx completion handling.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-9-git-send-email-ppranees@codeaurora.org
In datapath, add branch predictors where required in the process rx().
This protects high value rx path without having performance overhead.
Also while processing rx packets, the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-8-git-send-email-ppranees@codeaurora.org
The usage of quota variable inside ath11k_dp_rx_process_received_packets()
is redundant. Since we would queue only max packets to the list before
calling this function so it would never exceed quota. Hence removing
usage of quota variable.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-7-git-send-email-ppranees@codeaurora.org
The Active Pdev and CAC check are done for each msdu in
ath11k_dp_rx_process_received_packets which is a overhead.
To avoid this overhead, collect all msdus in a per mac msdu
list and pass to function.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-6-git-send-email-ppranees@codeaurora.org
In ath11k_dp_process_rx(), after processing rx_desc from
ath11k_hal_srng_dst_get_next_entry(), ath11k_hal_srng_dst_num_free()
is accessed everytime because of done flag is not set.
To avoid this additional access to ath11k_hal_srng_dst_num_free(),
increment total_msdu_reaped only when continuation is not set and
update done flag correspondingly.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-5-git-send-email-ppranees@codeaurora.org
In data path, to reduce the CPU cycles spending on descriptor access
wrapper function, changed those functions as static inline.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-4-git-send-email-ppranees@codeaurora.org
tcl_data and reo_dst rings are currently being allocated using
dma_allocate_coherent() which is non cacheable.
Allocating ring memory from cacheable memory area allows cached descriptor
access and prefetch next descriptors to optimize CPU usage during
descriptor processing on NAPI. Based on the hardware param we can enable
or disable this feature for the corresponding platform.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-3-git-send-email-ppranees@codeaurora.org
Host driver doesn't need to process CE8 interrupts (used
by target independently)
The volume of interrupts is huge within short interval,
CPU0 CPU1 CPU2 CPU3
14022188 0 0 0 GIC 71 Edge ce8
Hence disabling unused CE8 interrupt will improve CPU usage.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-2-git-send-email-ppranees@codeaurora.org
Currently the updated bandwidth for the peer will be configured
to the firmware after channel switch from the sta_rc_update_wk.
If the updated bandwidth is greater than the configured peer phymode
during the peer assoc may result firmware assert.
For example, initially AP is in HE40 mode and the peer phymode is
configured as MODE_11AX_HE40 during peer assoc. Now user change the
channel width to HE80 then, the peer bandwidth will be updated as
HE80 to the firmware.
This will trigger firmware assert due to peer bandwidth is greater than
the peer phymode.
Fix this issue by sending peer assoc command before setting the updated
peer bandwith to firmware.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636644002-25446-1-git-send-email-quic_vnaralas@quicinc.com
Below compilation error is reported when built with W=1,
drivers/net/wireless/ath/ath11k/mac.c:5408:22: error: parameter 'changed_flags' set but not used [-Werror,-Wunused-but-set-parameter]
changed_flags is set, but left unused. So, remove unnecessary set.
Compile tested only.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636609967-5114-1-git-send-email-quic_seevalam@quicinc.com
In CE pipe cleanup, DMA memory gets freed by the aligned address
(base_addr_owner_space) which is wrong. It needs to be freed
by the address (base_addr_owner_space_unaligned) returned by
dma_alloc. So free the dma memory by the proper address.
This was found in code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636561290-18966-1-git-send-email-quic_periyasa@quicinc.com
