Currently, the ath11k_soc_dp_stats::hal_reo_error array is defined with a
maximum size of DP_REO_DST_RING_MAX. However, the ath11k_dp_process_rx()
function access ath11k_soc_dp_stats::hal_reo_error using the REO
destination SRNG ring ID, which is incorrect. SRNG ring ID differ from
normal ring ID, and this usage leads to out-of-bounds array access. To fix
this issue, modify ath11k_dp_process_rx() to use the normal ring ID
directly instead of the SRNG ring ID to avoid out-of-bounds array access.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240704070811.4186543-3-quic_periyasa@quicinc.com
Commit 3a415daa3e ("wifi: ath11k: add P2P IE in beacon template")
from Feb 28, 2024 (linux-next), leads to the following Smatch static
checker warning:
drivers/net/wireless/ath/ath11k/wmi.c:1742 ath11k_wmi_p2p_go_bcn_ie()
warn: sleeping in atomic context
The reason is that ath11k_bcn_tx_status_event() will directly call might
sleep function ath11k_wmi_cmd_send() during RCU read-side critical
sections. The call trace is like:
ath11k_bcn_tx_status_event()
-> rcu_read_lock()
-> ath11k_mac_bcn_tx_event()
-> ath11k_mac_setup_bcn_tmpl()
……
-> ath11k_wmi_bcn_tmpl()
-> ath11k_wmi_cmd_send()
-> rcu_read_unlock()
Commit 886433a984 ("ath11k: add support for BSS color change") added the
ath11k_mac_bcn_tx_event(), commit 01e782c891 ("ath11k: fix warning
of RCU usage for ath11k_mac_get_arvif_by_vdev_id()") added the RCU lock
to avoid warning but also introduced this BUG.
Use work queue to avoid directly calling ath11k_mac_bcn_tx_event()
during RCU critical sections. No need to worry about the deletion of vif
because cancel_work_sync() will drop the work if it doesn't start or
block vif deletion until the running work is done.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: 3a415daa3e ("wifi: ath11k: add P2P IE in beacon template")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/2d277abd-5e7b-4da0-80e0-52bd96337f6e@moroto.mountain/
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240626053543.1946-1-quic_kangyang@quicinc.com
An iommu domain is allocated in ath11k_ahb_fw_resources_init() and is
attached to ab_ahb->fw.dev in the same function.
Use iommu_paging_domain_alloc() to make it explicit.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20240610085555.88197-12-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
We have moved to a new group-managed repo, and this is the first pull
request from that repo, and from me. Fingers crossed...
We have some new features in ath12k along with some cleanups in ath11k
and ath12k. Also notable are some device-tree changes to allow certain
ath11k and ath12k devices to work with a new power sequencing
subsystem.
Major changes:
ath12k
* DebugFS support for datapath statistics
* WCN7850: support for WoW (Wake on WLAN)
* WCN7850: device-tree bindings
ath11k
* QCA6390: device-tree bindings
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQQ/mtSHzPUi16IfDEksFbugiYzLewUCZoQU7hQcampvaG5zb25A
a2VybmVsLm9yZwAKCRAsFbugiYzLe6vCAP9mt6rfI2SWucd0ex9XbXwVkN7vV5Qn
NCvRXeT5QlnfFQEAt0DBUnmU/CuShroshEw2kXKLHJpZ1y6Oz6YVN49ECAU=
=ArqZ
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20240702' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patches for v6.11
We have moved to a new group-managed repo, and this is the first pull
request from that repo, and from me. Fingers crossed...
We have some new features in ath12k along with some cleanups in ath11k
and ath12k. Also notable are some device-tree changes to allow certain
ath11k and ath12k devices to work with a new power sequencing
subsystem.
Major changes:
ath12k
* DebugFS support for datapath statistics
* WCN7850: support for WoW (Wake on WLAN)
* WCN7850: device-tree bindings
ath11k
* QCA6390: device-tree bindings
Currently, the calculation of the average signal strength in station mode
is incorrect.
This is because before calculating the average signal strength, ath11k need
to determine whether the hardware and firmware support db2dbm, if the
hardware and firmware support db2dbm, do not need to add noise floor,
otherwise, need to add noise floor.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240309121129.5379-1-quic_lingbok@quicinc.com
Currently, the calculation of ack signal strength is incorrect.
This is because before calculating the ack signal strength, ath11k need
to determine whether the hardware and firmware support db2dbm. If the
hardware and firmware support db2dbm, do not need to add noise floor,
otherwise, need to add noise floor.
Besides, the value of ack_rssi passed by firmware to ath11k should be a
signed number, so change its type to s8.
After that, "iw wlan0 station dump" show the correct ack signal strength.
Such as:
root@CDCCSTEX0799733-LIN:~# iw wlp88s0 station dump
Station 00:03:7f:12:df:df (on wlp88s0)
inactive time: 75 ms
rx bytes: 11599
rx packets: 99
tx bytes: 9029
tx packets: 81
tx retries: 4
tx failed: 0
rx drop misc: 2
signal: -16 dBm
signal avg: -24 dBm
tx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
tx duration: 9230 us
rx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
rx duration: 7201 us
last ack signal:-23 dBm
avg ack signal: -22 dBm
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240611022550.59078-1-quic_lingbok@quicinc.com
Currently for CCMP256, GCMP128 and GCMP256 ciphers, in ath11k_install_key()
IEEE80211_KEY_FLAG_GENERATE_IV_MGMT is not set. And in ath11k_mac_mgmt_tx_wmi()
a length of IEEE80211_CCMP_MIC_LEN is reserved for all ciphers.
This results in unexpected management frame drop in case either of above 3 ciphers
is used. The reason is, without IEEE80211_KEY_FLAG_GENERATE_IV_MGMT set, mac80211
will not generate CCMP/GCMP headers in frame for ath11k. Also MIC length reserved
is wrong. Such frame is dropped later by hardware:
ath11k_pci 0000:5a:00.0: mac tx mgmt frame, buf id 0
ath11k_pci 0000:5a:00.0: mgmt tx compl ev pdev_id 1, desc_id 0, status 1
From user point of view, we have observed very low throughput due to this issue:
action frames are all dropped so ADDBA response from DUT never reaches AP. AP
can not use aggregation thus throughput is low.
Fix this by setting IEEE80211_KEY_FLAG_GENERATE_IV_MGMT flag and by reserving proper
MIC length for those ciphers.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Tested-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Closes: https://lore.kernel.org/all/CADS+iDX5=JtJr0apAtAQ02WWBxgOFEv8G063vuGYwDTC8AVZaw@mail.gmail.com
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240605014826.22498-1-quic_bqiang@quicinc.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240603091541.8367-2-wsa+renesas@sang-engineering.com
Current documentation on RCU in ath11k_mac_op_ipv6_changed() says:
/* Note: read_lock_bh() calls rcu_read_lock() */
read_lock_bh(&idev->lock);
This is wrong because without enabling CONFIG_PREEMPT_RT
rcu_read_lock() is not called by read_lock_bh(). The reason
why current code works even in a CONFIG_PREEMPT_RT=n kernel
is because atomic_notifier_call_chain() already does that for
us, see:
int atomic_notifier_call_chain()
{
...
rcu_read_lock();
ret = notifier_call_chain(&nh->head, val, v, -1, NULL);
rcu_read_unlock();
...
}
and backtrace:
ath11k_mac_op_ipv6_changed
ieee80211_ifa6_changed
notifier_call_chain
atomic_notifier_call_chain
So update the comment to make it correct.
This is found during code review, compile tested only.
Fixes: feafe59c89 ("wifi: ath11k: use RCU when accessing struct inet6_dev::ac_list")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240531022411.6543-1-quic_bqiang@quicinc.com
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have two
conflicts this time:
CONFLICT (content): Merge conflict in net/mac80211/cfg.c
CONFLICT (content): Merge conflict in drivers/net/wireless/microchip/wilc1000/netdev.c
Here are Stephen's resolutions for them:
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au/https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au/
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* Enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZi07URHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZu3/QgAo7jyKgvpwMaNIVRLyfYCo0r3Q9wb7QPd
QeRNsftYxlWpPTJ4+Y95aZupy91Ay+RaEQXbbtl7PMIiyQrs7wb4V4Iqzedkws3t
DZsR5BitH+1BIGY0Omo0fiSB5HlWEwZGUj6inqlgKHpBtdIVTANSMjuwkdoMAV5y
ZU57axIGToySvDbRlhJQW833Nnh4KnaseA+TtyfXSaBVerzbshkjBr0d9pMBMiH9
irMQW5CW+7fbxp3OCNsKxX4eG6MFGmm/uP1hFmeYQi2qzUE4SddHMeV4I6oNKOrH
vFB+ZVmYvOjJUYsNhlCUe6Vy+EKwvmfiDWwE1egelEkgozCixJXAAQ==
=QT4C
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.11
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have
two conflicts this time:
net/mac80211/cfg.c
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au
drivers/net/wireless/microchip/wilc1000/netdev.c
https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA)
support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
* tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (194 commits)
wifi: ath12k: add hw_link_id in ath12k_pdev
wifi: ath12k: add panic handler
wifi: rtw89: chan: Use swap() in rtw89_swap_sub_entity()
wifi: brcm80211: remove unused structs
wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type)
wifi: ath12k: do not process consecutive RDDM event
dt-bindings: net: wireless: ath11k: Drop "qcom,ipq8074-wcss-pil" from example
wifi: ath12k: fix memory leak in ath12k_dp_rx_peer_frag_setup()
wifi: rtlwifi: handle return value of usb init TX/RX
wifi: rtlwifi: Enable the new rtl8192du driver
wifi: rtlwifi: Add rtl8192du/sw.c
wifi: rtlwifi: Constify rtl_hal_cfg.{ops,usb_interface_cfg} and rtl_priv.cfg
wifi: rtlwifi: Add rtl8192du/dm.{c,h}
wifi: rtlwifi: Add rtl8192du/fw.{c,h} and rtl8192du/led.{c,h}
wifi: rtlwifi: Add rtl8192du/rf.{c,h}
wifi: rtlwifi: Add rtl8192du/trx.{c,h}
wifi: rtlwifi: Add rtl8192du/phy.{c,h}
wifi: rtlwifi: Add rtl8192du/hw.{c,h}
wifi: rtlwifi: Add new members to struct rtl_priv for RTL8192DU
wifi: rtlwifi: Add rtl8192du/table.{c,h}
...
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Link: https://lore.kernel.org/r/20240607093517.41394C2BBFC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
-----BEGIN PGP SIGNATURE-----
iQFLBAABCgA1FiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZgjPUXHHF1aWNfa3Zh
bG9AcXVpY2luYy5jb20ACgkQbhckVSbrbZuVggf/SUE9KjLAt4HBg3ag6Kj5E6U+
c9Z2oCaqCpSMP2K48PMekSJuemr92gVvs1g7I1ksOsgIpFVsNozgnb9SQVDJn9Py
kO53Vi0W7a3EoQ+zLv+YZGEguj5TUN5ijj4W6zG9AInNwDKbz4vcaART70WUbjtN
maxBnxMvSnCcHjfnam2GfDd5nK+Te/DrOZqIMxMWFlKOQLmNLfFWxdN6MHCNiBYf
1v3i4r6RkwFWLsafcMoDJJc5AbEK38Gp1h5/QeGZo3nCokknW8e7s7nDFifoOVSQ
k1AiWIIy8zj0HixAFfUwON+APdAWNENJiIoUMIt8j5dAcxoLa3fMFYM16qClew==
=8QAR
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20240605' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.11
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
ath.git fixes for 6.10. Two fixes for user reported regressions in
ath11k. One dependency fix and one error path fix.
-----BEGIN PGP SIGNATURE-----
iQFLBAABCgA1FiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZaAPoXHHF1aWNfa3Zh
bG9AcXVpY2luYy5jb20ACgkQbhckVSbrbZsyFAf/R3y+MhEEMgQRHiBddHrzCWb0
J0z88GoUtQL5R8nYZu7jwyl9OozR8EpdHHmnapvvZ4AXY00CC5yFEJeZkWEEttNk
DY2th3sEy0MlQmHs1C57Y1vAHQnClQpyRtohw6kxl5u8SZlB7TAfd+20aJiYstTA
DsmggxnXXg8ag9mtjweoMGnEoozQ39DRZ+fcMbVQAX322Vom3CIqEwJim27oVhve
2jY6La2T0t2y+xK7vQO7oqYtWYIu4yWvShyhqcMlOfs2It77UtjcnI1aKZXZ+ngK
EBNYPtf0i3Ik/MDd78d5F/jRddZTcw0ITyncfWaTr1xX9UwbpzfZDIt1uutZ6g==
=J1DD
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20240531' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
Merge ath-current from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
ath.git fixes for 6.10. Two fixes for user reported regressions in
ath11k. One dependency fix and one error path fix.
Base address of CE ring is defined as u32, currently this works
because coherent DMA mask configured as 32 bit:
#define ATH11K_PCI_COHERENT_DMA_MASK 32
However this mask could be changed once firmware bugs are fixed
to fully support 36 bit DMA addressing. So to protect against any
future changes to the DMA mask, change the type of the fields that
are dependent upon it.
This is found during code review. Compile tested only.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240524021558.34452-1-quic_bqiang@quicinc.com
ath11k_wmi_send_set_current_country_cmd() is called in several places
and all of them are just simply repeating the same logic.
Refactor to make code clean.
Compile tested only.
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240520024148.5472-2-quic_bqiang@quicinc.com
With commit bc8a0fac86 ("wifi: mac80211: don't set bss_conf in parsing")
ath11k fails to connect to 6 GHz AP.
This is because currently ath11k checks AP's power type in
ath11k_mac_op_assign_vif_chanctx() which would be called in AUTH stage.
However with above commit power type is not available until ASSOC stage.
As a result power type check fails and therefore connection fails.
Fix this by moving power type check to ASSOC stage, also move regulatory
rules update there because it depends on power type.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: bc8a0fac86 ("wifi: mac80211: don't set bss_conf in parsing")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240424064019.4847-1-quic_bqiang@quicinc.com
WCN6750 firmware crashes because of num_vdevs changed from 4 to 17
in ath11k_init_wmi_config_qca6390() as the ab->hw_params.num_vdevs
is 17. This is caused by commit f019f4dff2 ("wifi: ath11k: support
2 station interfaces") which assigns ab->hw_params.num_vdevs directly
to config->num_vdevs in ath11k_init_wmi_config_qca6390(), therefore
WCN6750 firmware crashes as it can't support such a big num_vdevs.
Fix it by assign 3 to num_vdevs in hw_params for WCN6750 as 3 is
sufficient too.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01371-QCAMSLSWPLZ-1
Fixes: f019f4dff2 ("wifi: ath11k: support 2 station interfaces")
Reported-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Closes: https://lore.kernel.org/r/D15TIIDIIESY.D1EKKJLZINMA@fairphone.com/
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240520030757.2209395-1-quic_cjhuang@quicinc.com
Instead of passing the full TPE elements, in all their glory
and mixed up data formats for HE backward compatibility, parse
them fully into the right values, and pass that to the drivers.
Also introduce proper validation already in mac80211, so that
drivers don't need to do it, and parse the EHT portions.
The code now passes the values in the right order according to
the channel used by an interface, which could also be a subset
of the data advertised by the AP, if we couldn't connect with
the full bandwidth (for whatever reason.)
Also add kunit tests for the more complicated bits of it.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240506214536.2aa839969b60.I265b28209e0b29772b2f125f7f83de44a4da877b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The chanctx can be shared, but it seems like the TPE values for
this vif should only reflect the channel that the vif uses, which
is captured in bss_conf->chanreq.oper rather than the chanctx.
Use that when calculating defaults, a similar issue is where the
data from the AP is processed, but I'm moving that to mac80211.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240506214536.d99fcf5856b9.I359bb401ea74bf82dc981a86a7ca3fa44d169d2e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The define IEEE80211_MAX_NUM_PWR_LEVEL doesn't make much
sense. Yes, that table has a maximum value of 8, and the
table will actually remain that way, but EHT introduced
a way to encode more levels for 320 MHz channels.
Remove IEEE80211_MAX_NUM_PWR_LEVEL and, for ath11k being
the only user, add ATH11K_NUM_PWR_LEVELS, where it makes
sense since it cannot support 320 MHz channels.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240506214536.9818e5471055.Icece7e47e963d6b68e0d97ba13c102b37fbaa689@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
If one of the dummy allocation fails in ath11k_pcic_ext_irq_config(),
the previous allocated devices might leak due to returning without
deallocating the devices.
Instead of returning on the error path, deallocate all the previously
allocated net_devices and then return.
Fixes: bca592ead8 ("wifi: ath11k: allocate dummy net_device dynamically")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508185902.70975-1-leitao@debian.org
smatch flagged the following issue:
drivers/net/wireless/ath/ath11k/qmi.c:2401 ath11k_qmi_load_file_target_mem() error: uninitialized symbol 'ret'.
The reality is that 'ret' is initialized in every path through
ath11k_qmi_load_file_target_mem() except one, the case where the input
'len' is 0, and hence the "while (remaining)" loop is never entered.
But to make sure this case is also handled, add an initializer to the
declaration of 'ret'.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240504-qmi_load_file_target_mem-v1-2-069fc44c45eb@quicinc.com
If STATUS_BUFFER_DONE is not set for a monitor status ring entry,
we don't process the status ring until STATUS_BUFFER_DONE set
for that status ring entry.
During LMAC reset it may happen that hardware will not write
STATUS_BUFFER_DONE tlv in status buffer, in that case we end up
waiting for STATUS_BUFFER_DONE leading to backpressure on monitor
status ring.
To fix the issue, when HP (Head Pointer) + 1 entry is peeked and if DMA is not
done and if HP + 2 entry's DMA done is set, replenish HP + 1 entry and start
processing in next interrupt. If HP + 2 entry's DMA done is not set, poll onto
HP + 1 entry DMA done to be set.
Also, during monitor attach HP points to the end of the ring and TP (Tail
Pointer) points to the start of the ring. Using ath11k_hal_srng_src_peek() may
result in processing invalid buffer for the very first interrupt. Since, HW
starts writing buffer from TP.
To avoid this issue call ath11k_hal_srng_src_next_peek() instead of
calling ath11k_hal_srng_src_peek().
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Co-developed-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429073624.736147-1-quic_tamizhr@quicinc.com
Currently, in ath11k_ahb_probe(), if a failure occurs after
ath11k_ahb_ce_remap() is called, and if hw_params->ce_remap is
enabled, the CE register memory is not unmapped. So add a call to
ath11k_ahb_ce_unmap() in the error path.
This issue was identified by smatch/smatch_scripts/kchecker:
drivers/net/wireless/ath/ath11k/ahb.c:1218 ath11k_ahb_probe() warn: 'ab->mem_ce' from ioremap() not released on lines: 1218.
Since this is a rare error path with no simple way to test, and since
the change is trivial to review, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430-ce-unmap-v1-2-e468328f95d9@quicinc.com
Currently the logic that handles hw_params->ce_remap is inline code,
both for doing the remap and the unmap. An upcoming change needs to do
the unmap in a second place, so refactor the unmap logic into a
separate function. And although it is only called from one place,
refactor the remap logic as well to have functional symmetry.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430-ce-unmap-v1-1-e468328f95d9@quicinc.com
Simplify the loop by using list_for_each_entry(). No functional changes.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240411165516.4070649-3-kvalo@kernel.org
ath12k
* debugfs support
* dfs_simulate_radar debugfs file
* disable Wireless Extensions
* suspend and hibernation support
* ACPI support
* refactoring in preparation of multi-link support
ath11k
* support hibernation (required changes in qrtr and MHI subsystems)
* ieee80211-freq-limit Device Tree property support
ath10k
* firmware-name Device Tree property support
-----BEGIN PGP SIGNATURE-----
iQFLBAABCgA1FiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmYztxUXHHF1aWNfa3Zh
bG9AcXVpY2luYy5jb20ACgkQbhckVSbrbZs0NQf/dYF+Pjy3eh9vabwZ05rUZwLF
P/k7Q8o631Gl0LTkmGw6SseUFswAOH1uwaKpWQvjhzHE8Fy4ziMeQ+aruqtbfZ3i
Q1BYsnCbQHZ+1HX0EJmB9KDz8+/G1JxOlwiux7EsujOuFixjomm08VEJ4QXGVSnj
NnCg0zx/0njDqT/3KjJuoL4stAk0HDvIayiVGsQOwcQQJelLGudqTNmRPnKQkR5w
yRUX+NaFlVHgbbhsnEyW3XeqKVFwgy64BtNRIVpJ0lF51aazT80DagNmw5CawznC
uak1nFktAtX/AID3lWRjek3smIdlnUz39JojKW7iO60/wfZXXFbR8Xl2XEpp9g==
=fF10
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20240502' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.10
ath12k
* debugfs support
* dfs_simulate_radar debugfs file
* disable Wireless Extensions
* suspend and hibernation support
* ACPI support
* refactoring in preparation of multi-link support
ath11k
* support hibernation (required changes in qrtr and MHI subsystems)
* ieee80211-freq-limit Device Tree property support
ath10k
* firmware-name Device Tree property support
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct ath11k_ext_irq_grp by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at ath11k_ahb_config_ext_irq() for ahb, and
ath11k_pcic_ext_irq_config() for pcic.
The free of the device occurs at ath11k_ahb_free_ext_irq() for the ahb
case, and ath11k_pcic_free_ext_irq() for the pcic case.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Tested-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
if (noa_descriptors > WMI_P2P_MAX_NOA_DESCRIPTORS), there is a mix of
return and goto. In such a case, 'td' should be freed to avoid a memory
leak.
While at it, change ath11k_wmi_p2p_noa_event() to return void.
'0' was returned in all cases, even in case of error and the only caller
does not handle the return value.
This is also more consistent with most of functions called from
ath11k_wmi_tlv_op_rx().
Fixes: 2408379f15 ("wifi: ath11k: implement handling of P2P NoA event")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/07f1fc75b2d5b4173ae1b7bb1da5be7f6fc608c8.1713212781.git.christophe.jaillet@wanadoo.fr
Commit c3718936ec ("ipv6: anycast: complete RCU handling of struct
ifacaddr6") converted struct inet6_dev::ac_list to use RCU but missed that
ath11k also accesses this list. Now sparse warns:
drivers/net/wireless/ath/ath11k/mac.c:9145:21: warning: incorrect type in assignment (different address spaces)
drivers/net/wireless/ath/ath11k/mac.c:9145:21: expected struct ifacaddr6 *ifaca6
drivers/net/wireless/ath/ath11k/mac.c:9145:21: got struct ifacaddr6 [noderef] __rcu *ac_list
drivers/net/wireless/ath/ath11k/mac.c:9145:53: warning: incorrect type in assignment (different address spaces)
drivers/net/wireless/ath/ath11k/mac.c:9145:53: expected struct ifacaddr6 *ifaca6
drivers/net/wireless/ath/ath11k/mac.c:9145:53: got struct ifacaddr6 [noderef] __rcu *aca_next
Fix it by using rtnl_dereference(). Also add a note that read_lock_bh() calls
rcu_read_lock() which I was not aware of.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: c3718936ec ("ipv6: anycast: complete RCU handling of struct ifacaddr6")
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240411165516.4070649-2-kvalo@kernel.org
Now that all infrastructure is in place and ath11k is fixed to handle all the
corner cases, power down the ath11k firmware during suspend and power it back
up during resume. This fixes the problem when using hibernation with ath11k PCI
devices.
For suspend, two conditions needs to be satisfied:
1. since MHI channel unprepare would be done in late suspend stage,
ath11k needs to get all QMI-dependent things done before that stage.
2. and because unprepare MHI channels requires a working MHI stack,
ath11k is not allowed to call mhi_power_down() until that finishes.
So the original suspend callback is separated into two parts: the first part
handles all QMI-dependent things in suspend callback; while the second part
powers down MHI in suspend_late callback. This is valid because kernel calls
ath11k's suspend callback before all suspend_late callbacks, making the first
condition happy. And because MHI devices are children of ath11k device
(ab->dev), kernel guarantees that ath11k's suspend_late callback is called
after QRTR's suspend_late callback, this satisfies the second condition.
Above analysis also applies to resume process. so the original resume
callback is separated into two parts: the first part powers up MHI stack
in resume_early callback, this guarantees MHI stack is working when
QRTR tries to prepare MHI channels (kernel calls QRTR's resume_early callback
after ath11k's resume_early callback, due to the child-father relationship);
the second part waits for the completion of restart, which won't fail now
since MHI channels are ready for use by QMI.
Another notable change is in power down path, we tell mhi_power_down() to not
to destroy MHI devices, making it possible for QRTR to help unprepare/prepare
MHI channels, and finally get us rid of the probe-defer issue when resume.
Also change related code due to interface changes.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240305021320.3367-4-quic_bqiang@quicinc.com
kernel-doc flagged the following issue, so fix it:
drivers/net/wireless/ath/ath11k/hal.h:668: warning: missing initial short description on line:
* enum hal_rx_buf_return_buf_manager
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240329-hal_rx_buf_return_buf_manager-v1-1-e62ec9dc2af9@quicinc.com
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() will be converted as weel if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
CC: Kalle Valo <kvalo@kernel.org>
CC: Jeff Johnson <jjohnson@kernel.org>
CC: linux-wireless@vger.kernel.org
CC: ath11k@lists.infradead.org
CC: ath10k@lists.infradead.org
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240315055211.1347548-1-lizhijian@fujitsu.com
There are some duplicate definitions in wmi.h, remove them.
No functional changes, compile tested only.
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240314021654.304451-1-quic_kangyang@quicinc.com
Currently we do reset for each RDDM event from MHI, however there are
cases, see below log, that we get two or more consecutive events, and
it is pointless to do reset for the subsequent ones. What's more, it
makes reset process more likely to fail.
[ 1502.115876] ath11k_pci 0000:04:00.0: boot notify status reason MHI_CB_EE_RDDM
[ 1502.115884] ath11k_pci 0000:04:00.0: firmware crashed: MHI_CB_EE_RDDM
[ 1502.224041] ath11k_pci 0000:04:00.0: boot notify status reason MHI_CB_EE_RDDM
[ 1502.224050] ath11k_pci 0000:04:00.0: firmware crashed: MHI_CB_EE_RDDM
Add a check to avoid reset again and again. This is done by tracking previous
MHI status: if we receive a new RDDM event while the previous one is
also the same, we treat it as duplicate and ignore it, because normally
we should receive a MHI_CB_EE_MISSION_MODE event between them.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240111071406.14053-1-quic_bqiang@quicinc.com
Now that all the necessary pieces are implemented we can enable P2P
support for QCA6390/WCN6855/QCA2066.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.2
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240228093537.25052-7-quic_kangyang@quicinc.com
Current ROC scan will filter probe request. So P2P device cannot receive
probe request. But it is necessary for P2P mode. A P2P device cannot be
discovered if it doesn't respond to others' probe request.
In addition, station won't filter probe request with common scan. But
for station, there is no needed to receive probe request.
Based on the above two points, change scan flag scan_f_filter_prb_req
for QCA6390/WCN6855/QCA2066.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.2
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240228093537.25052-6-quic_kangyang@quicinc.com
Mac80211 needs more space for P2P scan ie in P2P mode, 256 is not
enough, resize it to 512.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.2
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240228093537.25052-5-quic_kangyang@quicinc.com
The NoA(Notice of Absence) attribute is used by the P2P Group Owner to
signal its absence due to power save timing, concurrent operation, or
off-channel scanning. It is also used in the P2P Presence Request-Response
mechanism.
The NoA attribute shall be present in the P2P IE in the beacon frames
transmitted by a P2P Group Owner when a NoA schedule is being advertised,
or when the CTWindow is non-zero.
So add support to update P2P information after P2P GO is up through
event WMI_P2P_NOA_EVENTID, and always put it in probe resp.
Create p2p.c and p2p.h for P2P related functions and definitions.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.2
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240228093537.25052-4-quic_kangyang@quicinc.com
P2P Element is a necessary component of P2P protocol communication.
It contains the Vendor Specific Information Element which includes
the WFA OUI and an OUI Type indicating P2P.
Add P2P IE in beacon template, and implement WMI interface for it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.2
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240228093537.25052-3-quic_kangyang@quicinc.com
Current interface combination doesn't support P2P mode.
So change it for P2P mode.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.2
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240228093537.25052-2-quic_kangyang@quicinc.com
Currently we force enable power save on non-running vdevs, this results
in unexpected ping latency in below scenarios:
1. disable power save from userspace.
2. trigger suspend/resume.
With step 1 power save is disabled successfully and we get a good latency:
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=5.13 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=5.45 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=5.99 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=6.34 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=4.47 ms
64 bytes from 192.168.1.1: icmp_seq=6 ttl=64 time=6.45 ms
While after step 2, the latency becomes much larger:
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=17.7 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=15.0 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=14.3 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=16.5 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=20.1 ms
The reason is, with step 2, power save is force enabled due to vdev not
running, although mac80211 was trying to disable it to honor userspace
configuration:
ath11k_pci 0000:03:00.0: wmi cmd sta powersave mode psmode 1 vdev id 0
Call Trace:
ath11k_wmi_pdev_set_ps_mode
ath11k_mac_op_bss_info_changed
ieee80211_bss_info_change_notify
ieee80211_reconfig
ieee80211_resume
wiphy_resume
This logic is taken from ath10k where it was added due to below comment:
Firmware doesn't behave nicely and consumes more power than
necessary if PS is disabled on a non-started vdev.
However we don't know whether such an issue also occurs to ath11k firmware
or not. But even if it does, it's not appropriate because it goes against
userspace, even cfg/mac80211 don't know we have enabled it in fact.
Remove it to fix this issue. In this way we not only get a better latency,
but also, and the most important, keeps the consistency between userspace
and kernel/driver. The biggest price for that would be the power consumption,
which is not that important, compared with the consistency.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: b2beffa7d9 ("ath11k: enable 802.11 power save mode in station mode")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240309113115.11498-1-quic_bqiang@quicinc.com
On QCA6390/QCN9074/WCN6855, MHISTATUS may still have SYSERR bit set
after SOC_GLOBAL_RESET.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/ZeWEqGVibkMg2APi@ns.kevlo.org
Currently the soc_dp_stats debugfs file has the following permissions:
# ls -l /sys/kernel/debug/ath11k/pci-0000:03:00.0/soc_dp_stats
-rw------- 1 root root 0 Mar 4 15:04 /sys/kernel/debug/ath11k/pci-0000:03:00.0/soc_dp_stats
However this file does not actually support write operations -- no .write()
method is registered. Therefore use the correct permissions when creating
the file.
After the change:
# ls -l /sys/kernel/debug/ath11k/pci-0000:03:00.0/soc_dp_stats
-r-------- 1 root root 0 Mar 4 15:15 /sys/kernel/debug/ath11k/pci-0000:03:00.0/soc_dp_stats
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240305-fix-soc_dp_stats-permission-v1-1-2ec10b42f755@quicinc.com
ath11k inherited struct wmi_start_scan_arg from ath10k. However, in
ath11k, this struct is unused -- struct scan_req_params is used for
this functionality. So remove the unused struct.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240226-ath11k-obsolete-wmi_start_scan_arg-v1-1-c0b94c6e191d@quicinc.com
Unlike the event configuration which can be modified by MHI, the
channel and controller configurations are expected to be const. And
since they are not modified locally, constify them to prevent runtime
modification.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223-mhi-const-wifi-ath11k-v1-1-51b9d42d2639@quicinc.com
Currently buf_len field of ath11k_mhi_config_qca6390 is assigned
with 0, making MHI use a default size, 64KB, to allocate channel
buffers. This is likely to fail in some scenarios where system
memory is highly fragmented and memory compaction or reclaim is
not allowed.
There is a fail report which is caused by it:
kworker/u32:45: page allocation failure: order:4, mode:0x40c00(GFP_NOIO|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 19318 Comm: kworker/u32:45 Not tainted 6.8.0-rc3-1.gae4495f-default #1 openSUSE Tumbleweed (unreleased) 493b6d5b382c603654d7a81fc3c144d59a1dfceb
Workqueue: events_unbound async_run_entry_fn
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x60
warn_alloc+0x13a/0x1b0
? srso_alias_return_thunk+0x5/0xfbef5
? __alloc_pages_direct_compact+0xab/0x210
__alloc_pages_slowpath.constprop.0+0xd3e/0xda0
__alloc_pages+0x32d/0x350
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__kmalloc_large_node+0x72/0x110
__kmalloc+0x37c/0x480
? mhi_map_single_no_bb+0x77/0xf0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__mhi_prepare_for_transfer+0x44/0x80 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? __pfx_____mhi_prepare_for_transfer+0x10/0x10 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
device_for_each_child+0x5c/0xa0
? __pfx_pci_pm_resume+0x10/0x10
ath11k_core_resume+0x65/0x100 [ath11k a5094e22d7223135c40d93c8f5321cf09fd85e4e]
? srso_alias_return_thunk+0x5/0xfbef5
ath11k_pci_pm_resume+0x32/0x60 [ath11k_pci 830b7bfc3ea80ebef32e563cafe2cb55e9cc73ec]
? srso_alias_return_thunk+0x5/0xfbef5
dpm_run_callback+0x8c/0x1e0
device_resume+0x104/0x340
? __pfx_dpm_watchdog_handler+0x10/0x10
async_resume+0x1d/0x30
async_run_entry_fn+0x32/0x120
process_one_work+0x168/0x330
worker_thread+0x2f5/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe8/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Actually those buffers are used only by QMI target -> host communication.
And for WCN6855 and QCA6390, the largest packet size for that is less
than 6KB. So change buf_len field to 8KB, which results in order 1
allocation if page size is 4KB. In this way, we can at least save some
memory, and as well as decrease the possibility of allocation failure
in those scenarios.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Closes: https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223053111.29170-1-quic_bqiang@quicinc.com
Every time the firmware boots we call ath11k_core_qmi_firmware_ready() which
ends up calling ath11k_thermal_register(). So we try to register thermal
devices multiple times. And when we power off the firmware during
suspend/hibernation (implemented in the next patch) we get a warning in resume:
hwmon hwmon4: PM: parent phy0 should not be sleeping
Workaround this similarly like ath11k_mac_register() does by testing
ATH11K_FLAG_REGISTERED.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-6-quic_bqiang@quicinc.com
We are seeing below warning in both reset and suspend/resume scenarios:
[69663.691847] ath11k_pci 0000:02:00.0: Already processed, so ignoring dma ring caps
This is because ab->num_db_cap is not cleared in
ath11k_wmi_free_dbring_caps(), so clear it to avoid such
warnings.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-5-quic_bqiang@quicinc.com
Both the firmware reset feature and the power management
suspend/resume feature share common power-down and power-up
functionality. One aspect of the power-up functionality is
the handling of the ATH11K_QMI_EVENT_FW_INIT_DONE event.
When this event is received, a call is made to
ath11k_hal_dump_srng_stats(), with the purpose to collect
information that may be useful in debugging the cause of a
firmware reset.
Unfortunately, since this functionality is shared between
both the firmware reset path and the power management
resume path, the kernel log is flooded with messages during
resume. Since these messages are not useful during resume,
and in fact can be confusing and can increase the time it
takes to resume, update the logic to only call
ath11k_hal_dump_srng_stats() during firmware reset.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-4-quic_bqiang@quicinc.com
There is no driver to match these two channels, so
remove them. This fixes warnings from MHI subsystem during suspend:
mhi mhi0_LOOPBACK: 1: Failed to reset channel, still resetting
mhi mhi0_LOOPBACK: 0: Failed to reset channel, still resetting
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-3-quic_bqiang@quicinc.com
For non WoW suspend/resume, ath11k host powers down whole hardware
when suspend and powers up it when resume, the code path it goes
through is very like the ath11k reset logic.
In order to reuse that logic, rearrange IRQ handling in the reset
path.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-2-quic_bqiang@quicinc.com
We have support for QCA2066 now and also several new features in ath12k.
Major changes:
ath12k
* firmware-2.bin support
* support having multiple identical PCI devices (firmware needs to
have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
* QCN9274: support split-PHY devices
* WCN7850: enable Power Save Mode in station mode
* WCN7850: P2P support
ath11k:
* QCA6390 & WCN6855: support 2 concurrent station interfaces
* QCA2066 support
-----BEGIN PGP SIGNATURE-----
iQFLBAABCgA1FiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmXXA/YXHHF1aWNfa3Zh
bG9AcXVpY2luYy5jb20ACgkQbhckVSbrbZsfJQgAnqXLUIyHS873E4+OfEUIMZIu
/oFb9RzgU3Uv/8HWqwrXEtgbjthnxHWWVCEIR1roAEHX1vLxm5Wr0w4SsIRskwuK
8URUKIyHP4oep8TvA9uDrlQZ9PViDwW7F+Xc0nRh5c/AOi7bjMDCbJr7Sazjhsc5
JNYANHU1WSzc06hAk+3OrPON2e7EEpCkLDb7P1zVMF7uAxDovDpzGT+SXBTZu8Dw
UtiPbwTcGeUkBuMI4Mse6Jl/wAA2nWZXJXqPB1iilVwdz+VjksAZWODWS+m3UEW1
I+S8iYO0TWOSwGcu5rMyaeUMoGVSdu0Sw0h/2Ps7WGUoeZ8mT3Xwm6QrJBdpjg==
=UhMv
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20240222' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.9
We have support for QCA2066 now and also several new features in ath12k.
Major changes:
ath12k
* firmware-2.bin support
* support having multiple identical PCI devices (firmware needs to
have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
* QCN9274: support split-PHY devices
* WCN7850: enable Power Save Mode in station mode
* WCN7850: P2P support
ath11k:
* QCA6390 & WCN6855: support 2 concurrent station interfaces
* QCA2066 support
Currently, function to check if beacon countdown is complete uses deflink
to fetch the beacon and check the counter. However, with MLO, there is
a need to check the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240216144621.514385-2-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
QCA2066 is a PCI based DBS device. It is very similar to WCN6855
overall: they share the same PCI device ID, the same major and
minor version numbers, the same register address, and same HAL
descriptors etc. The most significant difference is that QCA2066
supports 3-antenna configuration while WCN6855 does not. To differentiate
them, subversion numbers are used. Currently four numbers are used
by QCA2066: 0x1019A0E1, 0x1019B0E1, 0x1019C0E1 and 0x1019D0E1.
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03737-QCAHSPSWPL_V2_SILICONZ_CE-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240109021336.4143-3-quic_bqiang@quicinc.com
In ath11k_pci_probe() there is a switch statement that, based
upon the PCI device ID, assigns pci_ops. After the switch,
ath11k_pcic_register_pci_ops() is called to register the pci_ops.
Unfortunately, this registration is too late if any of the cases
in the switch need to perform operations that require the pci_ops
to already be registered. In particular, an upcoming patch for
QCA2066 needs to call ath11k_pcic_read32().
To address this issue, call ath11k_pcic_register_pci_ops() from
each case instead of doing so after the switch. That way the ops
will be registered if any subsequent operations within the case
processing require the ops to be present.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240109021336.4143-2-quic_bqiang@quicinc.com
Provide address list to mac80211 so user doesn't need to specify addresses when
a second interface is added because the address can be allocated from the list
by mac80211.
The derived addresses have LAA (Local Administered Address) bit set, and only
the first byte is changed. Take the 00:03:7f:xx:xx:xx as example to derive:
addresses[0] is unchanged, it's still 00:03:7f:xx:xx:xx,
addresses[1] is 02:03:7f:xx:xx:xx,
addresses[2] is 12:03:7f:xx:xx:xx,
addresses[3] is 22:03:7f:xx:xx:xx,
addresses[4] is 32:03:7f:xx:xx:xx.
However as only 3 addresses are reported now, so addresses[3] and addresses[4]
aren't actually derived.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20230714023801.2621802-3-quic_cjhuang@quicinc.com
Add hardware parameter support_dual_stations to indicate whether 2 station
interfaces are supported. For chips which support this feature, limit total
number of AP interface and mesh point to 1. The max interfaces are 3 for such
chips.
The chips affected are:
QCA6390 hw2.0
WCN6855 hw2.0
WCN6855 hw2.1
Other chips are not affected.
For affected chips, remove radar_detect_widths because now
num_different_channels is set to 2. radar_detect_widths can be set only when
num_different_channels is 1, see mac80211 function wiphy_verify_combinations
for details. This means that in affectected chips DFS cannot be enabled in AP
mode.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20230714023801.2621802-2-quic_cjhuang@quicinc.com
Now that we do not use scan_flags directly with WMI_SCAN_XXX macros anymore but
only the bitfield scan_f_xxx, lets remove the scan_flags & the underlying union.
This will prevent further problems as some entries in the scan_f_xxx bitfield
don't match their corresponding WMI_SCAN_XXX flags as seen in [1]
[1] https://lore.kernel.org/all/20231127180559.1696041-1-nico.escande@gmail.com/
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240209113536.266822-3-nico.escande@gmail.com
As discussed in [1] lets not use WMI_SCAN_XXX defines in combination with
scan_flags directly when setting scan params in struct scan_req_params but use
the underlying bitfield. This bitfield is then converted to WMI_SCAN_XXX when
filling the WMI command to send to the firmware.
[1] https://lore.kernel.org/all/871qae51wx.fsf@kernel.org/
Tested-on: QCN9074 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240209113536.266822-2-nico.escande@gmail.com
Get rid of gfp parameter from ieee80211_obss_color_collision_notify
since it is no longer used.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/f91e1c78896408ac556586ba8c99e4e389aeba02.1707389901.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently ieee80211_csa_finish() function finalizes CSA by scheduling a
finalizing worker using the deflink. With MLO, there is a need to do it
on a given link basis.
Pass link ID of the link on which CSA needs to be finalized.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, function to update beacon counter uses deflink to fetch
the beacon and then update the counter. However, with MLO, there is
a need to update the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data during beacon update counter.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-3-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 9476cda44c ("wifi: ath11k: Consistently use ath11k_vif_to_arvif()")
previously replaced all open coding of the ath11k_vif_to_arvif()
functionality. Subsequently two more instances of open coding were
introduced, one in commit 92425f788f ("wifi: ath11k: fill parameters for
vdev set tpc power WMI command") and one in commit 6f4e235be6 ("wifi:
ath11k: add parse of transmit power envelope element"), so fix those as
well.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240205-ath11k_vif_to_arvif-v1-1-7c41313c8318@quicinc.com
Currently, at the end of ath11k_mac_fill_reg_tpc_info(), the
reg_tpc_info struct is populated, including the following:
reg_tpc_info->is_psd_power = is_psd_power;
reg_tpc_info->eirp_power = eirp_power;
Kernel test robot complains on uninitialized symbol:
drivers/net/wireless/ath/ath11k/mac.c:7949
ath11k_mac_fill_reg_tpc_info() error: uninitialized symbol 'eirp_power'.
This is because there are some code paths that never set eirp_power, so
the assignment of reg_tpc_info->eirp_power can come from an
uninitialized variable. Functionally this is OK since the eirp_power
only has meaning when is_psd_power is true, and all code paths which set
is_psd_power to true also set eirp_power. However, to keep the robot
happy, always initialize eirp_power before use.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 92425f788f ("wifi: ath11k: fill parameters for vdev set tpc power WMI command")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202024011.11341-1-quic_bqiang@quicinc.com
Currently in ath11k_peer_assoc_h_he() rx_mcs_80 and rx_mcs_160
are used to calculate max_nss, see
if (support_160)
max_nss = min(rx_mcs_80, rx_mcs_160);
else
max_nss = rx_mcs_80;
Kernel test robot complains on uninitialized symbols:
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_160'.
drivers/net/wireless/ath/ath11k/mac.c:2323 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
This is because there are some code paths that never set them, so
the assignment of max_nss can come from uninitialized variables.
This could result in some unknown issues since a wrong peer_nss
might be passed to firmware.
Change to initialize them to an invalid value at the beginning. This
makes sense because even max_nss gets an invalid value, due to either
or both of them being invalid, we can get an valid peer_nss with
following guard:
arg->peer_nss = min(sta->deflink.rx_nss, max_nss)
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 3db26ecf71 ("ath11k: calculate the correct NSS of peer for HE capabilities")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202023547.11141-1-quic_bqiang@quicinc.com
Currently when connecting to an AP with 11AX-HE phy mode, host sends
WMI_VDEV_PARAM_SET_HEMU_MODE parameter to firmware after
WMI_PEER_ASSOC_CMDID command. This results in TXBF not working, because
firmware calculates TXBF values while handling WMI_PEER_ASSOC_CMDID,
however at that time WMI_VDEV_PARAM_SET_HEMU_MODE has not been sent yet.
See below log:
AP sends "VHT/HE/EHT NDP Announcement" to station, and station sends
"Action no Ack" of category code HE to AP, the "Nc Index" and
"Codebook Information" are wrong:
Issued action:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 152
HE MIMO Control: 0x0004008018
.... .... .... .... .... .... .... .... .... .000 = Nc Index: 1 Column (0)
.... .... .... .... .... .... .... ..0. .... .... = Codebook Information: 0
Change to send WMI_VDEV_PARAM_SET_HEMU_MODE before WMI_PEER_ASSOC_CMDID,
then firmware will calculate the TXBF values with valid parameters
instead of empty values. TXBF works well and throughput performance is
improved from 80 Mbps to 130 Mbps with this patch.
Good action after this patch:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 409
HE MIMO Control: 0x0004008219
.... .... .... .... .... .... .... .... .... .001 = Nc Index: 2 Columns (1)
.... .... .... .... .... .... .... ..1. .... .... = Codebook Information: 1
This change applies to all chipsets.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 38dfe775d0 ("wifi: ath11k: push MU-MIMO params from hostapd to hardware")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240131021832.17298-1-quic_bqiang@quicinc.com
We have new features for both ath11k and ath12k. ath12k is now under
heavy refactoring in preparation for MLO support.
Major changes:
ath12k
* refactoring in preparation for Multi-Link Operation (MLO) support
* 1024 Block Ack window size support
* provide firmware wmi logs via a trace event
ath11k
* 36 bit DMA mask support
* support 6 GHz station power modes: Low Power Indoor (LPI), Standard
Power) SP and Very Low Power (VLP)
-----BEGIN PGP SIGNATURE-----
iQFLBAABCgA1FiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmW49dUXHHF1aWNfa3Zh
bG9AcXVpY2luYy5jb20ACgkQbhckVSbrbZsGagf+PmejP9HDXTB8RmL0exK79XyJ
DDn2a1elnnUNwf1SLrRTVZ83dtoN2V48A4/xQUhNfjs7vDUvvRj/vbUx2pe3CGoJ
9qUMO2/U7KxfEb4wo+iib51lD4B00/QaQIqC/nKY6xc85GIdUEdIfMXyEN2OF0Zz
BYEILiQtRdWYWmemesVv7goumpSEsReIdoETwMdVze8/geOluiy6UCBW7bh6BAi8
U9aaDEZuPfuvCWCWeCWNTN+xJNHSdLsdjSPZD+zq0jLHcuD1GmDJYQ5r67ZvUjM+
rS39DnJrDtTfiGMwIieGOy2zSCZZSVlyjFJuL9+P0X5N8A5057YIa+CZjeLCpw==
=mU6W
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20240130' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.9
We have new features for both ath11k and ath12k. ath12k is now under
heavy refactoring in preparation for MLO support.
Major changes:
ath12k
* refactoring in preparation for Multi-Link Operation (MLO) support
* 1024 Block Ack window size support
* provide firmware wmi logs via a trace event
ath11k
* 36 bit DMA mask support
* support 6 GHz station power modes: Low Power Indoor (LPI), Standard
Power) SP and Very Low Power (VLP)
Currently ath11k_mac_op_unassign_vif_chanctx() deletes peer but
ath11k_mac_op_assign_vif_chanctx() doesn't create it. This results in
connection failure if MAC80211 calls drv_unassign_vif_chanctx() and
drv_assign_vif_chanctx() during AUTH and ASSOC, see below log:
[ 102.372431] wlan0: authenticated
[ 102.372585] ath11k_pci 0000:01:00.0: wlan0: disabling HT/VHT/HE as WMM/QoS is not supported by the AP
[ 102.372593] ath11k_pci 0000:01:00.0: mac chanctx unassign ptr ffff895084638598 vdev_id 0
[ 102.372808] ath11k_pci 0000:01:00.0: WMI vdev stop id 0x0
[ 102.383114] ath11k_pci 0000:01:00.0: vdev stopped for vdev id 0
[ 102.384689] ath11k_pci 0000:01:00.0: WMI peer delete vdev_id 0 peer_addr 20:e5:2a:21:c4:51
[ 102.396676] ath11k_pci 0000:01:00.0: htt peer unmap vdev 0 peer 20:e5:2a:21:c4:51 id 3
[ 102.396711] ath11k_pci 0000:01:00.0: peer delete resp for vdev id 0 addr 20:e5:2a:21:c4:51
[ 102.396722] ath11k_pci 0000:01:00.0: mac removed peer 20:e5:2a:21:c4:51 vdev 0 after vdev stop
[ 102.396780] ath11k_pci 0000:01:00.0: mac chanctx assign ptr ffff895084639c18 vdev_id 0
[ 102.400628] wlan0: associate with 20:e5:2a:21:c4:51 (try 1/3)
[ 102.508864] wlan0: associate with 20:e5:2a:21:c4:51 (try 2/3)
[ 102.612815] wlan0: associate with 20:e5:2a:21:c4:51 (try 3/3)
[ 102.720846] wlan0: association with 20:e5:2a:21:c4:51 timed out
The peer delete logic in ath11k_mac_op_unassign_vif_chanctx() is
introduced by commit b4a0f54156 ("ath11k: move peer delete after
vdev stop of station for QCA6390 and WCN6855") to fix firmware
crash issue caused by unexpected vdev stop/peer delete sequence.
Actually for a STA interface peer should be deleted in
ath11k_mac_op_sta_state() when STA's state changes from
IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST, which also coincides
with current peer creation design that peer is created during
IEEE80211_STA_NOTEXIST -> IEEE80211_STA_NONE transition. So move
peer delete back to ath11k_mac_op_sta_state(), also stop vdev before
deleting peer to fix the firmware crash issue mentioned there. In
this way the connection failure mentioned here is also fixed.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: b4a0f54156 ("ath11k: move peer delete after vdev stop of station for QCA6390 and WCN6855")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123025700.2929-5-quic_bqiang@quicinc.com
Currently ath11k_mac_start_vdev_delay() needs a forward declaration because
it is defined after where it is called. Avoid this by re-arranging
ath11k_mac_station_add() and ath11k_mac_op_sta_state().
No functional changes. Compile tested only.
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123025700.2929-4-quic_bqiang@quicinc.com
In ath11k_mac_op_assign_vif_chanctx(), there is a logic to
create peer using ar->mac_addr for a STA vdev. This is invalid
because a STA vdev should have a peer created using AP's
MAC address. Besides, if we run into that logic, it means a peer
has already been created earlier, we should not create it again.
So remove it.
This is found during code review.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123025700.2929-2-quic_bqiang@quicinc.com
Currently 32 bit DMA mask is used, telling kernel to get us an DMA
address under 4GB when mapping a buffer. This results in a very high
CPU overhead in the case where IOMMU is disabled and more than 4GB
system memory is installed. The reason is, with more than 4GB memory
installed, kernel is likely to allocate a buffer whose physical
address is above 4GB. While with IOMMU disabled, kernel has to involve
SWIOTLB to map/unmap that buffer, which consumes lots of CPU cycles.
We did hit an issue caused by the reason mentioned above: in a system
that disables IOMMU and gets 8GB memory installed, a total of 40.5%
CPU usage is observed in throughput test. CPU profiling shows nearly
60% of CPU cycles are consumed by SWIOTLB.
By enabling 36 bit DMA mask, we can bypass SWIOTLB for any buffer
whose physical address is below 64GB. There are two types of DMA mask
within struct device, named dma_mask and coherent_dma_mask. Here we
only enable 36 bit for dma_mask, because firmware crashes if
coherent_dma_mask is also enabled, due to some unknown hardware
limitations. This is acceptable because coherent_dma_mask is used for
mapping a consistent DMA buffer, which generally does not happen in
a hot path.
With this change, the total CPU usage mentioned in above issue drops
to 18.9%.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123015201.28939-1-quic_bqiang@quicinc.com
The most visible fix here is the ath11k crash fix which was introduced
in v6.7. We also have a fix for iwlwifi memory corruption and few
smaller fixes in the stack.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmWuipMRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt17wgAhrkxpwRpMuRrV6VxHl9m+NXk7is2vni2
JZbqlvMIw1Hm+40K9D0WgFdNZUeAtBcd567MAbiqdzqRNB9DtEvnsXIKlKINwxIA
QFskkXR1f0sj79Hz3q7iWQq+jxDvAU5tge/WU65Na7+224sdyzBg7DZab8/buOsm
1xdx69MtGNU+dm4+V1Xp8h9jB7WAjq7N+ZhC6YfH6QSCL7JSL9Co/NC098gBnAEx
cm59vPOxk8+QoHKDjjmClTIhxOEgR6pSM8T3Dne9OYO8ONhxqdVSgd0Br+mEZgQ4
r61i88zK6ZmVZYckk6fhuGCLiKC6CFwS0eCLDQnKK1ufyRxDi84Y/Q==
=Cwmf
-----END PGP SIGNATURE-----
Merge tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.8-rc2
The most visible fix here is the ath11k crash fix which was introduced
in v6.7. We also have a fix for iwlwifi memory corruption and few
smaller fixes in the stack.
* tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix race condition on enabling fast-xmit
wifi: iwlwifi: fix a memory corruption
wifi: mac80211: fix potential sta-link leak
wifi: cfg80211/mac80211: remove dependency on non-existing option
wifi: cfg80211: fix missing interfaces when dumping
wifi: ath11k: rely on mac80211 debugfs handling for vif
wifi: p54: fix GCC format truncation warning with wiphy->fw_version
====================
Link: https://lore.kernel.org/r/20240122153434.E0254C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mac80211 started to delete debugfs entries in certain cases, causing a
ath11k to crash when it tried to delete the entries later. Fix this by
relying on mac80211 to delete the entries when appropriate and adding
them from the vif_add_debugfs handler.
Fixes: 0a3d898ee9 ("wifi: mac80211: add/remove driver debugfs entries as appropriate")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218364
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115101805.1277949-1-benjamin@sipsolutions.net
ENOTSUPP is not a standard error code, don't use it. Replace with
EOPNOTSUPP instead.
No functional changes, compile tested only.
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240117080431.2907471-3-quic_periyasa@quicinc.com
Commit 7636c9a6e7 ("wifi: ath11k: Add multi TX ring support for WCN6750")
added HAL_RX_BUF_RBM_SW4_BM to enum hal_rx_buf_return_buf_manager. However,
as flagged by the kernel-doc script, the documentation was not updated:
drivers/net/wireless/ath/ath11k/hal.h:689: warning: Enum value 'HAL_RX_BUF_RBM_SW4_BM' not described in enum 'hal_rx_buf_return_buf_manager'
So update the documentation. No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240111-document-hal_rx_buf_rbm_sw4_bm-v1-1-ad277e8ab3cc@quicinc.com
When station is connected to a 6 GHz AP, it has 2 ways to configure
the power limit to firmware. The first way is to send 2 WMI commands
WMI_PDEV_PARAM_TXPOWER_LIMIT2G/WMI_PDEV_PARAM_TXPOWER_LIMIT5G to
firmware, the second way is to send WMI_VDEV_SET_TPC_POWER_CMDID to
firmware which include more parameters for power control.
When firmware supports SERVICE_EXT_TPC_REG, it means firmware supports
WMI_VDEV_SET_TPC_POWER_CMDID, then ath11k selects the second way.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-13-quic_bqiang@quicinc.com
Add the handler for WMI_VDEV_SET_TPC_POWER_CMDID, it is for 6 GHz band.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-12-quic_bqiang@quicinc.com
Firmware advertises support for SERVICE_EXT_TPC_REG via a WMI service bit.
Add the definition of this service bit so that a subsequent patch can
check whether or not firmware supports this service.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-11-quic_bqiang@quicinc.com
Prepare the parameters which are needed for WMI command WMI_VDEV_SET_TPC_POWER_CMDID.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-10-quic_bqiang@quicinc.com
Save the max transmit power received in the vdev start response event from
firmware. A subsequent patch will use this to calculate the final power
value for WMI_VDEV_SET_TPC_POWER_CMDID.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-9-quic_bqiang@quicinc.com
The transmit power envelope element has some fields for power, ath11k
should parse it according to IEEE Std 802.11ax™‐2021.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-8-quic_bqiang@quicinc.com
Save the power spectral density (PSD) report from firmware to struct
ieee80211_reg_rule.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-7-quic_bqiang@quicinc.com
When station connect to AP on 6 GHz band, it needs switch the regulatory
rules according to the regulatory info sub field in HE operation element.
Switch to the power type which AP used for station interface.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-6-quic_bqiang@quicinc.com
There are two power types for 6 GHz regulatory, one is AP, another
is client.
When firmware boots up, WMI_REG_CHAN_LIST_CC_EXT_EVENTID is sent from
firmware at an early stage, the interface mode is not decided at
this point, then ath11k select reg rules of AP type as default.
After interface is created, it is exactly decided the interface
type such as AP/mesh point/station. Then ath11k need to update
reg rules to the exact power type matched to the interface type.
The client power type is used for station interface, and AP power
type is used for AP/mesh point interface.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-5-quic_bqiang@quicinc.com
spin_lock()/spin_unlock() are used in ath11k_reg_chan_list_event() to
acquire/release ab->base_lock. For now this is safe because that
function is only called in soft IRQ context.
But ath11k_reg_chan_list_event() will be called from process
context in an upcoming patch, and this can result in a deadlock if
ab->base_lock is acquired in process context and then soft IRQ occurs
on the same CPU and tries to acquire that lock.
Fix it by using spin_lock_bh() and spin_unlock_bh() instead.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 69a0fcf8a9 ("ath11k: Avoid reg rules update during firmware recovery")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-4-quic_bqiang@quicinc.com
The regulatory info of WMI_REG_CHAN_LIST_CC_EXT_EVENTID is not saved
in ath11k now, the info should be saved in ath11k. Save the info for
each radio and support switch regulatory rules dynamically.
As mac.c will also call ath11k_reg_handle_chan_list() in next patches move the
function to reg.c.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-3-quic_bqiang@quicinc.com
There are 3 types of regulatory rules for AP mode and 6 type for
station mode. Add wmi_vdev_type and ieee80211_ap_reg_power to
select the exact reg rules.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-2-quic_bqiang@quicinc.com
virt_to_phys() doesn't work on systems with IOMMU enabled, which have
non-identity physical-to-IOVA mappings. It leads to IO_PAGE_FAULTs like this:
[IO_PAGE_FAULT domain=0x0023 address=0x1cce00000 flags=0x0020]
And no association to the AP can be established.
This patch changes that to dma_map_single(), which works correctly. Even
virt_to_phys() documentation says device drivers should not use it:
This function does not give bus mappings for DMA transfers. In
almost all conceivable cases a device driver should not be using
this function
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Zhenghao Gu <imguzh@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231212031914.47339-1-imguzh@gmail.com
Since 'ath11k_wmi_tlv_parse_alloc()' always operates on
'skb->data, skb->len' tuple, it may be simplified to pass
the only 'skb' argument instead (which also implies
refactoring of 'ath11k_pull_bcn_tx_status_ev()' and
'ath11k_pull_chan_info_ev()' in the same way). Compile
tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214161117.75145-1-dmantipov@yandex.ru
In v6.7-rc1 sparse warns:
drivers/net/wireless/ath/ath11k/mac.c:4702:15: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:4702:15: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:8393:23: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:8393:23: error: too long token expansion
Workaround the warnings by refactoring the code to a new function, which also
reduces code duplication. And in the new function use max3() to make the code
more readable.
No functional changes, compile tested only.
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214161740.1582340-1-kvalo@kernel.org
Transform the zero-length ath11k_htc_record::credit_report array into
a proper flexible array. Since this is the only array in
ath11k_htc_record, remove the unnecessary union.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231205-flexarray-htc_record-v2-1-fbb56d436951@quicinc.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231117093056.873834-9-u.kleine-koenig@pengutronix.de
We are seeing below error randomly in the case where only
one MSI vector is configured:
kernel: ath11k_pci 0000:03:00.0: wmi command 16387 timeout
The reason is, currently, in ath11k_pcic_ext_irq_enable(),
ATH11K_FLAG_EXT_IRQ_ENABLED is set before NAPI is enabled.
This results in a race condition: after
ATH11K_FLAG_EXT_IRQ_ENABLED is set but before NAPI enabled,
CE interrupt breaks in. Since IRQ is shared by CE and data
path, ath11k_pcic_ext_interrupt_handler() is also called
where we call disable_irq_nosync() to disable IRQ. Then
napi_schedule() is called but it does nothing because NAPI
is not enabled at that time, meaning
ath11k_pcic_ext_grp_napi_poll() will never run, so we have
no chance to call enable_irq() to enable IRQ back. Finally
we get above error.
Fix it by setting ATH11K_FLAG_EXT_IRQ_ENABLED after all
NAPI and IRQ work are done. With the fix, we are sure that
by the time ATH11K_FLAG_EXT_IRQ_ENABLED is set, NAPI is
enabled.
Note that the fix above also introduce some side effects:
if ath11k_pcic_ext_interrupt_handler() breaks in after NAPI
enabled but before ATH11K_FLAG_EXT_IRQ_ENABLED set, nothing
will be done by the handler this time, the work will be
postponed till the next time the IRQ fires.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231117003919.26218-1-quic_bqiang@quicinc.com
Let ath11k select this option automatically which makes building
more intuitive if the user enables this driver (rather than the
driver not building unless CRYPTO_MICHAEL_MIC is explicitly enabled).
Further investigation shows that ath11k and ath12k are the only who use
'depends on' with CRYPTO_MICHAEL_MIC:
./drivers/net/wireless/intel/ipw2x00/Kconfig: select CRYPTO_MICHAEL_MIC
./drivers/net/wireless/intersil/hostap/Kconfig: select CRYPTO_MICHAEL_MIC
./drivers/net/wireless/intersil/orinoco/Kconfig: select CRYPTO_MICHAEL_MIC
./drivers/net/wireless/ath/ath11k/Kconfig: depends on CRYPTO_MICHAEL_MIC
./drivers/net/wireless/ath/ath12k/Kconfig: depends on CRYPTO_MICHAEL_MIC
./drivers/staging/rtl8192e/Kconfig: select CRYPTO_MICHAEL_MIC
./drivers/staging/ks7010/Kconfig: select CRYPTO_MICHAEL_MIC
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231113153544.282461-1-prestwoj@gmail.com
Currently wmi.h has two separate set of definitions for peer
flags. One set of flags is defined in enum wmi_tlv_peer_flags, and,
except for the last three, are named WMI_TLV_PEER_*. The other set of
flags are defined as macros, and are named WMI_PEER_*. The last three
macros have the same name as the last three wmi_tlv_peer_flags
enumerators.
The code only uses the WMI_PEER_* names; the WMI_TLV_PEER_* names are
unused. So as a first step in consolidation, remove all the
WMI_TLV_PEER_* names.
But since having an enum to define all the flags is actually a good
thing since that provides a handle by which to refer to the entire set
of flags, recast the WMI_PEER_* macros into enumerators.
Compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231106-ath-peer-flags-v1-3-781e83b7e8e8@quicinc.com
Currently both struct ath11k_pdev_wmi and struct ath11k_wmi_base
define:
const struct wmi_peer_flags_map *peer_flags;
But that member is not used, and in fact, struct wmi_peer_flags_map
is not defined within ath11k; these are obsolete remnants inherited
from ath10k. So remove them.
Compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231106-ath-peer-flags-v1-1-781e83b7e8e8@quicinc.com
Currently struct ath11k defines the following member:
struct ieee80211_ops *ops;
This is being flagged by checkpatch.pl:
WARNING: struct ieee80211_ops should normally be const
The original plan was to add the const qualifier. However, it turns
out this is actually unused, so remove it.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231106-ath12k-remove-ieee80211_ops-v1-1-d72cef1a855b@quicinc.com
If we already have gotten the rproc_handle (meaning the "qcom,rproc"
property is defined in the devicetree), it's a valid state that the
remoteproc module hasn't probed yet so we should defer probing instead
of just failing to probe.
This resolves a race condition when the ath11k driver probes and fails
before the wpss remoteproc driver has probed, like the following:
[ 6.232360] ath11k 17a10040.wifi: failed to get rproc
[ 6.232366] ath11k 17a10040.wifi: failed to get rproc: -22
[ 6.232478] ath11k: probe of 17a10040.wifi failed with error -22
...
[ 6.252415] remoteproc remoteproc2: 8a00000.remoteproc is available
[ 6.252776] remoteproc remoteproc2: powering up 8a00000.remoteproc
[ 6.252781] remoteproc remoteproc2: Booting fw image qcom/qcm6490/fairphone5/wpss.mdt, size 7188
So, defer the probe if we hit that so we can retry later once the wpss
remoteproc is available.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01264-QCAMSLSWPLZ-1.37886.3
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231027-ath11k-rproc-defer-v1-1-f6b6a812cd18@fairphone.com
The ath11k active pdevs are protected by RCU but the gtk offload status
event handling code calling ath11k_mac_get_arvif_by_vdev_id() was not
marked as a read-side critical section.
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Compile tested only.
Fixes: a16d9b50cf ("ath11k: support GTK rekey offload")
Cc: stable@vger.kernel.org # 5.18
Cc: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019155342.31631-1-johan+linaro@kernel.org
The ath11k active pdevs are protected by RCU but the htt pktlog handling
code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section.
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Compile tested only.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019112521.2071-1-johan+linaro@kernel.org
The ath11k active pdevs are protected by RCU but the DFS radar event
handling code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section.
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Compile tested only.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019153115.26401-3-johan+linaro@kernel.org
The ath11k active pdevs are protected by RCU but the temperature event
handling code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section as reported by RCU lockdep:
=============================
WARNING: suspicious RCU usage
6.6.0-rc6 #7 Not tainted
-----------------------------
drivers/net/wireless/ath/ath11k/mac.c:638 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
...
Call trace:
...
lockdep_rcu_suspicious+0x16c/0x22c
ath11k_mac_get_ar_by_pdev_id+0x194/0x1b0 [ath11k]
ath11k_wmi_tlv_op_rx+0xa84/0x2c1c [ath11k]
ath11k_htc_rx_completion_handler+0x388/0x510 [ath11k]
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: a41d10348b ("ath11k: add thermal sensor device support")
Cc: stable@vger.kernel.org # 5.7
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019153115.26401-2-johan+linaro@kernel.org
Firmware IE containers can dynamically provide various information
what firmware supports. Also it can embed more than one image so
updating firmware is easy, user just needs to update one file in
/lib/firmware/.
The firmware API 2 or higher will use the IE container format, the
current API 1 will not use the new format but it still is supported
for some time. Firmware API 2 files are named as firmware-2.bin
(which contains both amss.bin and m3.bin images) and API 1 files are
amss.bin and m3.bin.
Currently ath11k PCI driver provides firmware binary (amss.bin) path to
MHI driver, MHI driver reads firmware from filesystem and boots it. Add
provision to read firmware files from ath11k driver and provide the amss.bin
firmware data and size to MHI using a pointer.
Currently enum ath11k_fw_features is empty, the patches adding features will
add the flags.
With AHB devices there's no amss.bin or m3.bin, so no changes in how AHB
firmware files are used. But AHB devices can use future additions to the meta
data, for example in enum ath11k_fw_features.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Co-developed-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230727100430.3603551-4-kvalo@kernel.org
Simple refactoring to make it easier to add firmware-2.bin support in the
following patch.
Earlier ath11k_qmi_m3_load() supported changing m3.bin contents while ath11k is
running. But that's not going to actually work, m3.bin is supposed to be the
same during the lifetime of ath11k, for example we don't support changing the
firmware capabilities on the fly. Due to this ath11k requests m3.bin firmware
file first and only then checks m3_mem->vaddr, so we are basically requesting
the firmware file even if it's not needed. Reverse the code so that m3_mem
buffer is checked first, and only if it doesn't exist, then m3.bin is requested
from user space.
Checking for m3_mem->size is redundant when m3_mem->vaddr is NULL, we would
not be able to use the buffer in that case. So remove the check for size.
Simplify the exit handling and use 'goto out'.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20230727100430.3603551-3-kvalo@kernel.org
In PCI, thermal and HAL interface layer module, the identifier
sc is used to represent an instance of ath11k_base structure.
However, within ath11k, the convention is to use "ab" to
represent an SoC "base" struct. So change the all instances
of sc to ab.
Compile tested only.
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231014032650.32605-3-quic_periyasa@quicinc.com
In WMI layer module, the identifier wmi_sc is used to represent
an instance of ath11k_wmi_base structure. However, within ath11k,
the convention is to use "ab" to represent an SoC "base" struct.
So change the all instances of wmi_sc to wmi_ab.
Compile tested only.
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231014032650.32605-2-quic_periyasa@quicinc.com
Currently struct ath11k_base defines the member bd_api. However, this
member is only accessed within ath11k_core_fetch_bdf(). Since the
scope is local just to that one function, remove it from ath11k_base
and instead just use a local stack variable.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231013-ath11k_bd_api-v1-1-3fefe4629706@quicinc.com
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231009172923.2457844-11-robh@kernel.org
Currently, the logic to return an ath11k_sta pointer, given a
ieee80211_sta pointer, uses typecasting throughout the driver. In
general, conversion functions are preferable to typecasting since
using a conversion function allows the compiler to validate the types
of both the input and output parameters.
ath11k already defines a conversion function ath11k_vif_to_arvif() for
a similar conversion. So introduce ath11k_sta_to_arsta() for this use
case, and convert all of the existing typecasting to use this
function.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231009-ath11k_sta_to_arsta-v1-1-1563e3a307e8@quicinc.com
struct ath11k_htc_frame is unused, and since it illogically contains
two consecutive flexible arrays, it could never be used, so remove it.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231009-ath11k_htc_frame-v1-1-81d405b7a195@quicinc.com
Certain regulatory domains could put restrictions on phy mode operation.
For example, in a few countries HE Operation is not allowed. For such
countries, firmware indicates this via phy bitmap in each reg rule.
Currently, there is no logic to parse this info and then pass it on to the
cfg80211/regulatory.
Add parsing of this phy bitmap from the regulatory channel change event and
then accordingly map it to cfg80211/regulatory flags and pass it on to it.
While at it, correct typo in debug print s/dsf/dfs.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231004092655.25020-1-quic_adisi@quicinc.com
In v6.6-rc4 with GCC 13.2 I see a new warning:
drivers/net/wireless/ath/ath11k/debugfs.c: In function 'ath11k_debugfs_register':
drivers/net/wireless/ath/ath11k/debugfs.c:1597:51: error: '%d' directive output may be truncated writing between 1 and 3 bytes into a region of size 2 [-Werror=format-truncation=]
drivers/net/wireless/ath/ath11k/debugfs.c:1597:48: note: directive argument in the range [0, 255]
drivers/net/wireless/ath/ath11k/debugfs.c:1597:9: note: 'snprintf' output between 5 and 7 bytes into a destination of size 5
Increase the size of pdev_name to 10 bytes to make sure there's enough room for
the string. Also change the format to '%u' as ar->pdev_idx is u8.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231010062250.2580951-1-kvalo@kernel.org
Mac80211 does not set flags BSS_CHANGED_FILS_DISCOVERY and
BSS_CHANGED_UNSOL_BCAST_PROBE_RESP if there are no updates to
FILS discovery and unsolicited broadcast probe response transmission
configurations respectively. This results in the transmissions getting
stopped during BSS change operations which do not include these
attributes. Remove the checks for the flags and always send the existing
configuration to firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231004044915.6817-1-quic_alokad@quicinc.com
The first pull request for v6.7, with both stack and driver changes.
We have a big change how locking is handled in cfg80211 and mac80211
which removes several locks and hopefully simplifies the locking
overall. In drivers rtw89 got MCC support and smaller features to
other active drivers but nothing out of ordinary.
This pull request got delayed because we were waiting for the wireless
tree pull requested processed first and after that we merged wireless
into wireless-next to avoid several conflicts in the stack.
When pulling this there's one conflict in drivers/staging/rtl8723bs/os_dep/ioctl_cfg80211.c:
<<<<<<< HEAD
static int cfg80211_rtw_change_beacon(struct wiphy *wiphy,
struct net_device *ndev,
struct cfg80211_beacon_data *info)
=======
static int cfg80211_rtw_change_beacon(struct wiphy *wiphy, struct net_device *ndev,
struct cfg80211_ap_update *info)
>>>>>>> origin/merge-wireless-2023-10-05
Take the latter hunk which uses struct cfg80211_ap_update.
Major changes:
cfg80211
* remove wdev mutex, use the wiphy mutex instead
* annotate iftype_data pointer with sparse
* first kunit tests, for element defrag
* remove unused scan_width support
mac80211
* major locking rework, remove several locks like sta_mtx, key_mtx
etc. and use the wiphy mutex instead
* remove unused shifted rate support
* support antenna control in frame injection (requires driver support)
* convert RX_DROP_UNUSABLE to more detailed reason codes
rtw89
* TDMA-based multi-channel concurrency (MCC) support
iwlwifi
* support set_antenna() operation
* support frame injection antenna control
ath12k
* WCN7850: enable 320 MHz channels in 6 GHz band
* WCN7850: hardware rfkill support
* WCN7850: enable IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS to make scan faster
ath11k
* add chip id board name while searching board-2.bin
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmUgHYERHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtzIwf9Hn8lOUmbErtRmOjciesHoCvvjRelNuqG
ymUl/zdcXpl6ZEZZvvXTaUMFpbR1h8/8rfQABA91ADp/1ax4PKuIGtgBfkEkUelG
ONIbjJbYmPae8RZvAtBoy8k/QEt2NR97l1eRy+eqLovh273pFJu4eEW0AiLYJlZ8
rTAoej4RShhIvvh7O1zLt1It49tAFn+BwhDj6d3xCgdpmGJboJxwecEpqmJ0AVW9
pST5qDbANCbvfzElWswdCG48xludCtRG8WncJnkWjxeGqr+81yMrgIy+PQTwTAJ8
95Qe0sE9N5o9ZIE4hrdH+PuUYOCjD2O8IJFl6HkLeGh3Pr3+qGnxhQ==
=V52q
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-10-06' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.7
The first pull request for v6.7, with both stack and driver changes.
We have a big change how locking is handled in cfg80211 and mac80211
which removes several locks and hopefully simplifies the locking
overall. In drivers rtw89 got MCC support and smaller features to
other active drivers but nothing out of ordinary.
Major changes:
cfg80211
- remove wdev mutex, use the wiphy mutex instead
- annotate iftype_data pointer with sparse
- first kunit tests, for element defrag
- remove unused scan_width support
mac80211
- major locking rework, remove several locks like sta_mtx, key_mtx
etc. and use the wiphy mutex instead
- remove unused shifted rate support
- support antenna control in frame injection (requires driver support)
- convert RX_DROP_UNUSABLE to more detailed reason codes
rtw89
- TDMA-based multi-channel concurrency (MCC) support
iwlwifi
- support set_antenna() operation
- support frame injection antenna control
ath12k
- WCN7850: enable 320 MHz channels in 6 GHz band
- WCN7850: hardware rfkill support
- WCN7850: enable IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS to make scan faster
ath11k
- add chip id board name while searching board-2.bin
* tag 'wireless-next-2023-10-06' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (272 commits)
wifi: rtlwifi: remove unreachable code in rtl92d_dm_check_edca_turbo()
wifi: rtw89: debug: txpwr table supports Wi-Fi 7 chips
wifi: rtw89: debug: show txpwr table according to chip gen
wifi: rtw89: phy: set TX power RU limit according to chip gen
wifi: rtw89: phy: set TX power limit according to chip gen
wifi: rtw89: phy: set TX power offset according to chip gen
wifi: rtw89: phy: set TX power by rate according to chip gen
wifi: rtw89: mac: get TX power control register according to chip gen
wifi: rtlwifi: use unsigned long for rtl_bssid_entry timestamp
wifi: rtlwifi: fix EDCA limit set by BT coexistence
wifi: rt2x00: fix MT7620 low RSSI issue
wifi: rtw89: refine bandwidth 160MHz uplink OFDMA performance
wifi: rtw89: refine uplink trigger based control mechanism
wifi: rtw89: 8851b: update TX power tables to R34
wifi: rtw89: 8852b: update TX power tables to R35
wifi: rtw89: 8852c: update TX power tables to R67
wifi: rtw89: regd: configure Thailand in regulation type
wifi: mac80211: add back SPDX identifier
wifi: mac80211: fix ieee80211_drop_unencrypted_mgmt return type/value
wifi: rtlwifi: cleanup few rtlxxxx_set_hw_reg() routines
...
====================
Link: https://lore.kernel.org/r/87jzrz6bvw.fsf@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tx power is fetched from firmware's pdev stats. However, during active
CAC, firmware does not fill the current Tx power and sends the max
initialised value filled during firmware init. If host sends this power
to user space, this is wrong since in certain situations, the Tx power
could be greater than the max allowed by the regulatory. Hence, host
should not be fetching the Tx power during an active CAC.
Fix this issue by returning -EAGAIN error so that user space knows that there's
no valid value available.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: 9a2aa68afe ("wifi: ath11k: add get_txpower mac ops")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230912051857.2284-4-quic_adisi@quicinc.com
Currently channel definition's primary channel's DFS CAC time
as well as primary channel's state i.e usable are used to set
the CAC_RUNNING flag for the ath11k radio structure. However,
this is wrong since certain channel definition are possbile
where primary channel may not be a DFS channel but, secondary
channel is a DFS channel. For example - channel 36 with 160 MHz
bandwidth.
In such cases, the flag will not be set which is wrong.
Fix this issue by using cfg80211_chandef_dfs_usable() function
from cfg80211 which return trues if at least one channel is in
usable state.
While at it, modify the CAC running debug log message to print
the CAC time as well in milli-seconds.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230912051857.2284-3-quic_adisi@quicinc.com
ath.git patches for v6.7.
Major changes:
ath12k
* WCN7850: enable 320 MHz channels in 6 GHz band
* WCN7850: hardware rfkill support
* WCN7850: enable IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS to make scan faster
ath11k
* add chip id board name while searching board-2.bin
Commit e8c1841278 ("wifi: cfg80211: annotate iftype_data pointer with
sparse") added sparse checks for struct ieee80211_sband_iftype_data handling
which immediately found an issue in ath11k:
drivers/net/wireless/ath/ath11k/mac.c:7952:22: warning: incorrect type in argument 1 (different address spaces)
drivers/net/wireless/ath/ath11k/mac.c:7952:22: expected struct ieee80211_sta_he_cap const *he_cap
drivers/net/wireless/ath/ath11k/mac.c:7952:22: got struct ieee80211_sta_he_cap const [noderef] __iftype_data *
The problem here is that we are accessing sband->iftype_data directly even
though we should use for_each_sband_iftype_data() or similar. Fortunately
there's ieee80211_get_he_iftype_cap_vif() which is just what we need here so
use it to get HE capabilities.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230927142708.2897504-2-kvalo@kernel.org
When compiling with clang 16.0.6, I've noticed the following:
drivers/net/wireless/ath/ath11k/mac.c:8903:12: warning: stack frame
size (1032) exceeds limit (1024) in 'ath11k_mac_op_remain_on_channel'
[-Wframe-larger-than]
static int ath11k_mac_op_remain_on_channel(struct ieee80211_hw *hw,
^
68/1032 (6.59%) spills, 964/1032 (93.41%) variables
So switch to kzalloc()'ed instance of 'struct scan_req_params' like
it's done in 'ath11k_mac_op_hw_scan()'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230926042906.13725-1-dmantipov@yandex.ru
No need cast (void *) to (struct ath11k_base *),
struct hal_rx_msdu_link *), (struct ath11k_buffer_addr *) or
other types.
Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230919045150.524304-1-yunchuan@nfschina.com
Use 'kstrtoul_from_user()' in 'ath11k_write_file_spectral_count()'
and 'ath11k_write_file_spectral_bins()'
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230824075121.121144-4-dmantipov@yandex.ru
Remove set but otherwise unused 'wlan_init_status' and
'wmi_ready' members of 'struct ath11k_base', adjust
'ath11k_wmi_tlv_rdy_parse()' accordingly.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230824075121.121144-2-dmantipov@yandex.ru
In 'ath11k_dp_rx_mon_dest_process()', 'mon_dst_srng' points to
a member of 'srng_list', which is a fixed-size array inside
'struct ath11k_hal'. This way, if 'ring_id' is valid (i. e.
between 0 and HAL_SRNG_RING_ID_MAX - 1 inclusive), 'mon_dst_srng'
can't be NULL and so relevant check may be dropped.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230824075121.121144-1-dmantipov@yandex.ru
Since 'user_stats' is a fixed-size array of 'struct htt_ppdu_user_stats'
in 'struct htt_ppdu_stats', any of its member can't be NULL and so
relevant check may be dropped.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906093704.14001-1-dmantipov@yandex.ru
Commit 5b32b6dd96 ("ath11k: Remove core PCI references from
PCI common code") breaks with one MSI vector because it moves
affinity setting after IRQ request, see below log:
[ 1417.278835] ath11k_pci 0000:02:00.0: failed to receive control response completion, polling..
[ 1418.302829] ath11k_pci 0000:02:00.0: Service connect timeout
[ 1418.302833] ath11k_pci 0000:02:00.0: failed to connect to HTT: -110
[ 1418.303669] ath11k_pci 0000:02:00.0: failed to start core: -110
The detail is, if do affinity request after IRQ activated,
which is done in request_irq(), kernel caches that request and
returns success directly. Later when a subsequent MHI interrupt is
fired, kernel will do the real affinity setting work, as a result,
changs the MSI vector. However at that time host has configured
old vector to hardware, so host never receives CE or DP interrupts.
Fix it by setting affinity before registering MHI controller
where host is, for the first time, doing IRQ request.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01160-QCAMSLSWPLZ-1
Fixes: 5b32b6dd96 ("ath11k: Remove core PCI references from PCI common code")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230907015606.16297-1-quic_bqiang@quicinc.com
Sometimes board-2.bin does not have the board data which matched the
parameters such as bus type, vendor, device, subsystem-vendor,
subsystem-device, qmi-chip-id and qmi-board-id, then wlan will load fail.
Hence add another type which only matches the bus type and qmi-chip-id,
then the ratio of missing board data reduced.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230830060226.18664-1-quic_wgong@quicinc.com
There were are a number of cases in mac80211 and iwlwifi (at
least) that used the sband->iftype_data pointer directly,
instead of using the accessors to find the right array entry
to use.
Make sparse warn when such a thing is done.
To not have a lot of casts, add two helper functions/macros
- ieee80211_set_sband_iftype_data()
- for_each_sband_iftype_data()
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Correct parsing of reading offset for rx tid 16 bit bitmap. Incorrect
offset caused peer rx mu stats tid bitmap to always be zero. This
correction is in the software context and does not affect the
firmware interface.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00356-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1692827868-15667-2-git-send-email-quic_msinada@quicinc.com
Remove references to reserved fields and add new info fields for
struct hal_rx_ppdu_end_user_stats. Reserved fields should not be
accessed, therefore existing references to it are to be changed to
referencing specific info fields.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00356-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1692827868-15667-1-git-send-email-quic_msinada@quicinc.com
Currently, the ath11k driver does not print a crash signature when a
MHI_CB_EE_RDDM crash happens. Checked by triggering a simulated crash using the
command and checking dmesg for logs:
echo assert > /sys/kernel/debug/ath11k/../simulate_fw_crash
Add a warning when firmware crash MHI_CB_EE_RDDM happens.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Arowa Suliman <arowa@chromium.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230714001126.463127-1-arowa@chromium.org
-----BEGIN PGP SIGNATURE-----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=iFFM
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Add locking to read/modify/write PCIe Capability Register accessors
for Link Control and Root Control
- Use pci_dev_id() when possible instead of manually composing ID
from dev->bus->number and dev->devfn
Resource management:
- Move prototypes for __weak sysfs resource files to linux/pci.h to
fix 'no previous prototype' warnings
- Make more I/O port accesses depend on HAS_IOPORT
- Use devm_platform_get_and_ioremap_resource() instead of open-coding
platform_get_resource() followed by devm_ioremap_resource()
Power management:
- Ensure devices are powered up while accessing VPD
- If device is powered-up, keep it that way while polling for PME
- Only read PCI_PM_CTRL register when available, to avoid reading the
wrong register and corrupting dev->current_state
Virtualization:
- Avoid Secondary Bus Reset on NVIDIA T4 GPUs
Error handling:
- Remove unused pci_disable_pcie_error_reporting()
- Unexport pci_enable_pcie_error_reporting(), used only by aer.c
- Unexport pcie_port_bus_type, used only by PCI core
VGA:
- Simplify and clean up typos in VGA arbiter
Apple PCIe controller driver:
- Initialize pcie->nvecs (number of available MSIs) before use
Broadcom iProc PCIe controller driver:
- Use of_property_read_bool() instead of low-level accessors for
boolean properties
Broadcom STB PCIe controller driver:
- Assert PERST# when probing BCM2711 because some bootloaders don't
do it
Freescale i.MX6 PCIe controller driver:
- Add .host_deinit() callback so we can clean up things like
regulators on probe failure or driver unload
Freescale Layerscape PCIe controller driver:
- Add support for link-down notification so the endpoint driver can
process LINK_DOWN events
- Add suspend/resume support, including manual
PME_Turn_off/PME_TO_Ack handshake
- Save Link Capabilities during probe so they can be restored when
handling a link-up event, since the controller loses the Link Width
and Link Speed values during reset
Intel VMD host bridge driver:
- Fix disable of bridge windows during domain reset; previously we
cleared the base/limit registers, which actually left the windows
enabled
Marvell MVEBU PCIe controller driver:
- Remove unused busn member
Microchip PolarFlare PCIe controller driver:
- Fix interrupt bit definitions so the SEC and DED interrupt handlers
work correctly
- Make driver buildable as a module
- Read FPGA MSI configuration parameters from hardware instead of
hard-coding them
Microsoft Hyper-V host bridge driver:
- To avoid a NULL pointer dereference, skip MSI restore after
hibernate if MSI/MSI-X hasn't been enabled
NVIDIA Tegra194 PCIe controller driver:
- Revert 'PCI: tegra194: Enable support for 256 Byte payload' because
Linux doesn't know how to reduce MPS from to 256 to 128 bytes for
endpoints below a switch (because other devices below the switch
might already be operating), which leads to 'Malformed TLP' errors
Qualcomm PCIe controller driver:
- Add DT and driver support for interconnect bandwidth voting for
'pcie-mem' and 'cpu-pcie' interconnects
- Fix broken SDX65 'compatible' DT property
- Configure controller so MHI bus master clock will be switched off
while in ASPM L1.x states
- Use alignment restriction from EPF core in EPF MHI driver
- Add Endpoint eDMA support
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driver
- Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup
latency
- Add sa8775p DT binding and driver support
Rockchip PCIe controller driver:
- Use 64-bit mask on MSI 64-bit PCI address to avoid zeroing out the
upper 32 bits
SiFive FU740 PCIe controller driver:
- Set the supported number of MSI vectors so we can use all available
MSI interrupts
Synopsys DesignWare PCIe controller driver:
- Add generic dwc suspend/resume APIs (dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq()) to be called by controller driver
suspend/resume ops, and a controller callback to send PME_Turn_Off
MicroSemi Switchtec management driver:
- Add support for PCIe Gen5 devices
Miscellaneous:
- Reorder and compress to reduce size of struct pci_dev
- Fix race in DOE destroy_work_on_stack()
- Add stubs to avoid casts between incompatible function types
- Explicitly include correct DT includes to untangle headers"
* tag 'pci-v6.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (96 commits)
PCI: qcom-ep: Add ICC bandwidth voting support
dt-bindings: PCI: qcom: ep: Add interconnects path
PCI: qcom-ep: Treat unknown IRQ events as an error
dt-bindings: PCI: qcom: Fix SDX65 compatible
PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API
PCI: epf-mhi: Use iATU for small transfers
PCI: epf-mhi: Add support for SM8450
PCI: epf-mhi: Add eDMA support
PCI: qcom-ep: Add eDMA support
PCI: epf-mhi: Make use of the alignment restriction from EPF core
PCI/PM: Only read PCI_PM_CTRL register when available
PCI: qcom: Add support for sa8775p SoC
dt-bindings: PCI: qcom: Add sa8775p compatible
PCI: qcom-ep: Pass alignment restriction to the EPF core
PCI: Simplify pcie_capability_clear_and_set_word() control flow
PCI: Tidy config space save/restore messages
PCI: Fix code formatting inconsistencies
PCI: Fix typos in docs and comments
PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
PCI: Simplify pci_dev_driver()
...
A mouse that uses a USB connection is called a "USB mouse" device (or
"USB mouse" for short), not a "mouse USB" device. By analogy, a WiFi
adapter that connects to the host computer via USB is a "USB wireless"
device, not a "wireless USB" device. (The latter term more properly
refers to a defunct Wireless USB specification, which described a
technology for sending USB protocol messages over an ultra wideband
radio link.)
Similarly for a WiFi adapter card that plugs into a PCIe slot: It is a
"PCIe wireless" device, not a "wireless PCIe" device.
Rephrase the text in the kernel source where the word ordering is
wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/57da7c80-0e48-41b5-8427-884a02648f55@rowland.harvard.edu
Commit 2c3960c225 ("ath11k: setup ce tasklet for control path")
declared but never implemented ath11k_ce_map_service_to_pipe().
Commit e3396b8bdd ("ath11k: ce: support different CE configurations")
declared but never implemented ath11k_ce_attr_attach().
Commit d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
declared but never implemented ath11k_qmi_event_work()/ath11k_qmi_msg_recv_work().
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230811104413.33668-1-yuehaibing@huawei.com
'hw_rev' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
h11k/ahb.c:1124:11: error: cast to smaller integer type 'enum ath11k_hw_rev' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230810091224.70088-1-krzysztof.kozlowski@linaro.org
The init/exit() of driver only calls platform_driver_register/unregister,
it can be simpilfied with module_platform_driver.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230804091255.1347178-1-yangyingliang@huawei.com
