Multicast/broadcast traffic destined for a particular vlan group will
always be encrypted in software. To enable dynamic VLANs, it requires
driver support for sending software encrypted packets.
In ath10k, sending software encrypted frames is allowed only when we insmod
the driver with cryptmode param set to 1, this configuration disables
hardware crypto and enables RAW mode implicitly. Since, enabling raw
mode has performance impact, this cannot be considered as an ideal
solution for supporting VLANs in the driver.
As an alternative take, in this approach, cryptographic keys for
unicast traffic (per peer PTKs) and keys for non-vlan group traffic
will be configured in hardware, allowing hardware encryption for unicast
and non-vlan group traffic. Only vlan group traffic will be encrypted in
software and pushed to the target with encap mode set to RAW in the TX
descriptors.
Not all firmwares can support this type of key configuration(having few
keys installed in hardware and few only in software); for this purpose a
new WMI service flag "WMI_SERVICE_PER_PACKET_SW_ENCRYPT" is introduced to
advertise this support.
Also, adding the logic required to send sw encrypted frames in raw mode.
Hardwares Tested : QCA9984, QCA988X
Firmwares Tested : 10.4-3.5.3-00057, 10.2.4-1.0-00042
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure fine timing measurement (FTM) responder role from the
ftm_responder bss param sent by mac80211. With FTM functionality offloaded
to firmware, adding the interface allows userspace to enable or disable
FTM responder functionality. ath10k disables it at the time of interface
creation.
Supported FW: 10.4
Tested on IPQ4019 with firmware: 10.4-3.2.1.1-00022
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The airtime of a transmitted frame will be estimated from last used tx rate
which the firmware reports with the peer stats feature
(WMI_SERVICE_PEER_STATS). The airtime is computed on the tx path and it
will be reported to mac80211 upon tx completion.
This change is based on Kan's orginal commit in Chromium tree
("CHROMIUM: ath10k: Implementing airtime fairness based TX scheduler")
ref: https://chromium-review.googlesource.com/588190
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Signed-off-by: Kan Yan <kyan@google.com>
[rmanohar@codeaurora.org: ported only the airtime computation]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[toke@redhat.com: Rebase to mac80211-next, add test note]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k maintains common txqs list for all stations. This txq
management can be removed by migrating to mac80211 txq APIs
and let mac80211 handle txqs reordering based on reported airtime.
By doing this, txq fairness maintained in ath10k i.e processing
N frames per txq is removed. By adapting to mac80211 APIs,
ath10k will support mac80211 based airtime fairness algorithm.
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Tested-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 750afb08ca ("cross-tree: phase out dma_zalloc_coherent()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/ce.c:1602: line over 90 characters
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.
Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.
Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: b7ba83f7c4 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The support to put WCN3990 firmware into Factory
test mode is not present currently. The WCN3990
firmware can operate in Factory test mode based
on the mode it receives in the wlan enable message
from the host driver.
When the host driver is started in testmode send
the operating mode as UTF mode, to the WCN3990
firmware, in the wlan enable message to start the
firmware in Factory test mode.
Tested on: WCN3990
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The DIAG copy engine is only used via polling, but it holds a spinlock
with softirqs disabled. Each iteration of our read/write loops can
theoretically take 20ms (two 10ms timeout loops), and this loop can be
run an unbounded number of times while holding the spinlock -- dependent
on the request size given by the caller.
As of commit 39501ea641 ("ath10k: download firmware via diag Copy
Engine for QCA6174 and QCA9377."), we transfer large chunks of firmware
memory using this mechanism. With large enough firmware segments, this
becomes an exceedingly long period for disabling soft IRQs. For example,
with a 500KiB firmware segment, in testing QCA6174A, I see 200 loop
iterations of about 50-100us each, which can total about 10-20ms.
In reality, we don't really need to block softirqs for this duration.
The DIAG CE is only used in polling mode, and we only need to hold
ce_lock to make sure any CE bookkeeping is done without screwing up
another CE. Otherwise, we only need to ensure exclusion between
ath10k_pci_diag_{read,write}_mem() contexts.
This patch moves to use fine-grained locking for the shared ce_lock,
while adding a new mutex just to ensure mutual exclusion of diag
read/write operations.
Tested on QCA6174A, firmware version WLAN.RM.4.4.1-00132-QCARMSWPZ-1.
Fixes: 39501ea641 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW credit flow control is enabled for only WMI ctrl
service(CE3) but credit update is requested unconditionally
on all HTC services as part of HTC tx in CE3/CE0/CE4.
This is causing WOW failure as FW is not expecting credit
report request on other end-points(CE0/CE4).
Request credit report only on those endpoints where
credit flow control is enabled.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register snoc bus layer suspend/resume PM ops and configure
the wakeup source(CE2) for the device.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit 9d5804662c
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes: 9d5804662c ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.
To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on
commit d04ca38386 ("mt76x0u: fix suspend/resume"), so merge wireless-drivers
into wireless-drivers-next to get that.
ath.git patches for 5.1. Major changes:
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware releases
ath
* add new country codes for US
Firmware sends the tx_duration for each in HTT_T2H_MSG_TYPE_PEER_STATS
msg. Fill the tx_duration sent by firmware in the tx stats information
per STA.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware advertises the LDPC support information for HT in
HT capability info in the wmi service ready event. To provide
granularity, firmware now advertises WMI_HT_CAP_RX_LDPC and
WMI_HT_CAP_TX_LDPC separately. To support LDPC, host should
also check for WMI_HT_CAP_RX_LDPC and WMI_HT_CAP_TX_LDPC in HT
capabilities.
Add a condition to existing logic in host to know whether firmware
supports LDPC or not.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the transmit MSDU count for SDIO, to match with the descriptors
as used by the firmware. This also acts as a high watermark level for
transmit. Too many packets to the firmware results in transmit overflow
interrupt.
It only affect SDIO chip, it will not cause functionaly changes to
other hardware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/snoc.c: In function 'ath10k_snoc_tx_pipe_cleanup':
drivers/net/wireless/ath/ath10k/snoc.c:681:22: warning:
variable 'ar_snoc' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio_register_driver() doesn't do this for us, unlike (for example)
platform_driver_register(). This is important for helping track
module-to-device relationships.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The swap box flag of firmware is not set before htc ready, then it
will not set swap box flag in ath10k driver, and it will let swap
box setting not same between firmware and ath10k driver, then it
will trigger firmware assert failure.
Check the flag and set swap box after htc ready will fix the firmware
assert failure.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hw-restart crash inject mode is a special mode, where
there is no crash generated in the firmware, but instead
the driver restarts the firmware. In order to restart WCN3990
firmware, the driver needs to send qmi_wlan_disable message
followed by the qmi_wlan_enable message to the WCN3990 firmware.
Currently the qmi_wlan_disable message is not sent to
the WCN3990 firmware when hw-restart crash is injected,
which causes the firmware to crash when the driver sends
qmi_wlan_enable message during ath10k_restart.
Send qmi_wlan_disable to the WCN3990 firmware when the
hw-restart crash is injected via debugfs.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The management frames transmitted are dma mapped with
direction TO_DEVICE, but incorrectly mapped with
direction FROM_DEVICE during tx complete and error cases.
Fix the direction of dma during dma unmap of the
transmitted management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: 38a1390e02 ("ath10k: dma unmap mgmt tx buffer if wmi cmd send fails")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends tx completion of multiple management
frames bundled together in a single event, if the
host driver exposes the support to handle this
bundled tx completion event. This reduces the number
of WMI events which are sent to the host driver by
the target.
Set the BUNDLE_TX_COMPL flag in the host capability
flags when host sends the wmi init command, to indicate
the host capability to handle bundled tx completion for
management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.
Add support to handle the bundled tx completion
event for WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HOST capability interface data structures are updated
in HL3.1 fw version. Update the qmi host capability
members for compatibility across different firmware
versions.
Since this change breaks backward compatibility with
HL2.0 fw, HL2.0 fw upgrade to WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
or later version is required.
Testing:
Tested on QCS404 platform(WCN3990 HW).
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWoRZAAoJEG4XJFUm622bOm4H/j2Tt6qS5yz3ioH2I7R+f7e/
8C2JJia+uQs8iChdyCjCFcDymmjB2l5u72JvupwCdERzp3okv/xmJiLW5wFW2z4x
B3Nrd4FV2EMIdsRXg1RWbwZHC4wIY6lFhL1OcUcuNwpb5ab1ppvQFHmH5logd7DC
euFSe02g8xmXdUMciRDKGUdiSiDIApmx9dUfguaqYtepqeW3hmDEEkeDicaf2fjq
cM5qAvssIAgUTqwIImEQQEU7j7A2TgMYkRBNzwv2QG47jy6OlgXkZVByvtq59irg
v4BFNtG6uRWTugxQ/FwYWeqsrnjegFNKm5MFbS6BDxbe05M7QzeK8zm55fE9ZGk=
=cHbd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HTT aggr message parameter in HL2.0 fw are different in comparison
to legacy fw version. Fill correct HTT aggr msg parameter for
targets using HL2.0 firmware.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After system entering S5 (shut down but system still
providing power to QCA9377) on Ubuntu platform, power
consumption of QCA9377 is 69mA, which is too high.
The root cause is pci_soft_reset is not set for QCA9377
during pci probe.
To fix this issue, set 'pci_soft_reset' to 'th10k_pci_warm_reset',
and then the power consumption drops to a normal value(10mA).
Verified on Dell Ubuntu platform with firmware:
WLAN.TF.1.0-00002-QCATFSWPZ-5
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is a 37-bit target but can address memory range
only upto 35 bits. The 36th bit is used to control the
smmu/iommu translation and the 37th bit is used by the
internal bus masters to access the wifi subsystem internal
SRAM. With the DMA mask set to 37i-bit, the host driver
can get 37-bit dma address, which leads to incorrect
address access in the target.
Hence the host driver can used addresses upto 35-bit
for WCN3990. Fix the dma mask for wcn3990 to 35-bit,
instead of 37-bit.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is SNOC, not PCI. This prevents probing WCN3990.
Fixes: 367c899f62 ("ath10k: add bus type check in ath10k_init_hw_params")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address 00000286
pgd = d8754000
[00000286] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task: dc44cac0 ti: d4a38000 task.ti: d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<c02bdc50>] lr : [<bf916b78>] psr: 20000013
sp : d4a39b88 ip : 00000000 fp : 00000001
r10: 00000000 r9 : 1d3bc000 r8 : 00000dc0
r7 : 000080d0 r6 : d4a38000 r5 : dd401b00 r4 : 00000286
r3 : 00000000 r2 : d4a39ba0 r1 : 000080d0 r0 : dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5787d Table: 5a75406a DAC: 00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<c02bdc50>] (kmem_cache_alloc) from [<bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<bf916b78>] (ath10k_sta_state [ath10k_core]) from [<bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<bf88634c>] (ieee80211_add_station [mac80211]) from [<bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<bf83f3c4>] (nl80211_new_station [cfg80211]) from [<bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<bf6c4040>] (extack_doit [compat]) from [<c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<c05c285c>] (genl_rcv_msg) from [<c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<c05c1d98>] (netlink_rcv_skb) from [<c05c25d4>] (genl_rcv+0x20/0x34)
[<c05c25d4>] (genl_rcv) from [<c05c1750>] (netlink_unicast+0x11c/0x204)
[<c05c1750>] (netlink_unicast) from [<c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<c05c1be0>] (netlink_sendmsg) from [<c0587e90>] (sock_sendmsg+0x70/0x84)
[<c0587e90>] (sock_sendmsg) from [<c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c058970c>] (___sys_sendmsg.part.3) from [<c058a594>] (__sys_sendmsg+0x4c/0x70)
[<c058a594>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: ebfffec1 e1a04000 ea00001b e5953014 (e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes: a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HL2.0 firmware does not support setting quiet mode. If the host driver sends
the quiet mode setting command to the HL2.0 firmware, it crashes with the below
signature.
fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0
The quiet mode command support is exposed by the firmware via thermal throttle
wmi service. Enable ath10k thermal support if thermal throttle wmi service bit
is set. 10.x firmware versions support this feature by default, but
unfortunately do not advertise the support via service flags, hence have to
manually set the service flag in ath10k_core_compat_services().
Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990.
Co-developed-by: Govind Singh <govinds@codeaurora.org>
Co-developed-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 may call us with vif == NULL, if the station is not currently
active (e.g., not associated). It is trivially easy to reproduce a crash
by suspending the system when not connected to an AP:
[ 65.533934] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
[ 65.574521] pc : ath10k_flush+0x30/0xd0 [ath10k_core]
[ 65.574538] lr : __ieee80211_flush_queues+0x180/0x244 [mac80211]
[ 65.599680] Process kworker/u12:1 (pid: 57, stack limit = 0x(____ptrval____))
[ 65.599682] Call trace:
[ 65.599695] ath10k_flush+0x30/0xd0 [ath10k_core]
[ 65.642064] __ieee80211_flush_queues+0x180/0x244 [mac80211]
[ 65.642079] ieee80211_flush_queues+0x34/0x40 [mac80211]
[ 65.642095] __ieee80211_suspend+0xfc/0x47c [mac80211]
[ 65.658611] ieee80211_suspend+0x30/0x3c [mac80211]
[ 65.658627] wiphy_suspend+0x15c/0x3a8 [cfg80211]
[ 65.672810] dpm_run_callback+0xf0/0x1f0
[ 65.672814] __device_suspend+0x3ac/0x4f8
[ 65.672819] async_suspend+0x34/0xbc
[ 65.684096] async_run_entry_fn+0x54/0x104
[ 65.684099] worker_thread+0x4cc/0x72c
[ 65.684102] kthread+0x134/0x13c
[ 65.684105] ret_from_fork+0x10/0x18
Fixes: 9de4162f09 ("ath10k: add peer flush in ath10k_flush for STATION")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Not all devices using this driver are backed by a PCI device, so it's
not fair to assume 'to_pci_dev()' is valid. Fortunately, we only were
using this to convert straight back to a bare 'device', which means we
were only doing no-op pointer arithmetic, and not actually accessing
potentially out-of-bounds memory. But this is still bad practice.
Just use 'ar->dev' directly, since that's really all we're looking for.
Fixes: 209b2a68de ("ath10k: add platform regulatory domain support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 2ea9f12cef ("ath10k: add new cipher suite support") added a new
n_cipher_suites HW param with a fallback value and a warning log. Commit
03a72288c5 ("ath10k: wmi: add hw params entry for wcn3990") later
added WCN3990 HW entries, but it missed the n_cipher_suites.
Rather than seeing this warning every boot
ath10k_snoc 18800000.wifi: invalid hw_params.n_cipher_suites 0
let's provide the appropriate value.
Cc: Rakesh Pillai <pillair@qti.qualcomm.com>
Cc: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
They're provided as callbacks in ath10k_hif_ops and should be accessed
that way, if needed outside of snoc.c, and anyway, they're currently
unused outside snoc.c.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Similar to regulator error handling, we should only start tearing down
the 'i - 1' clock when clock 'i' fails to enable. Otherwise, we might
end up with an unbalanced clock, where we never successfully enabled the
clock, but we try to disable it anyway.
Fixes: a6a793f987 ("ath10k: vote for hardware resources for WCN3990")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I rarely see drivers specify precise voltage requirements like this, but
if we really have to...let's at least give a little wiggle room. Board
designs (and accompanying device trees) may not provide exactly the
voltage listed here, and we shouldn't fail to probe just because of
this.
Round these ranges down to the nearest volt, and provide a 0.05V margin.
The regulator should provide its own supported ranges, which will
helpfully intersect with these ranges.
I would just as well remove these ranges entirely, but if I understand
correctly, there's some reason that QCOM SoC's like to set zero /
non-zero voltages.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a regulator fails to set its voltage, we end up with an unbalanced
call to regulator_disable(), because the error path starts with the
current regulator (which was never enabled).
Factor out the "on" function to perform (and unwind if failed) a single
regulator at a time, and then main loop (ath10k_snoc_vreg_on()) can just
worry about unwinding the regulators that were already enabled.
It also helps to factor out the "off" function, to avoid repeating some
code here.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_wcn3990_clk_info and ath10k_wcn3990_vreg_info are not
WCN3990-specific structures. They hold generic data. So don't name them
with wcn3990 specifics.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/wmi-tlv.c: In function 'ath10k_wmi_tlv_op_gen_config_pno_start':
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3455:6: warning:
variable 'tlv_len' set but not used [-Wunused-but-set-variable]
It never used since inroduction in commit
ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to some spelling mistakes in ath10k_err and ath10k_dbg
messages:
"capablity" -> "capability"
"registed" -> "registered"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I had a couple concerns with this code. First, we definitely need to
set the error code if the kzalloc() fails. Secondly, I was worried that
if we didn't set "arsta->tx_stats" to NULL after freeing it, then it
looks to me like it might lead to a use after free. I can't test that,
but it's harmless to set it to NULL so I did.
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The host driver currently expects the channel info event to be
received in pairs for all the channels, i.e. the first
chan_info event for a particular channel will not have the
COMPLETE flag set and the second chan_info event for the
same channel will have the COMPLETE flag set.
The HL2.0 firmware sends only one channel info event per channel
which is scanned without the COMPLETE flag set. After sending the
chan_info_event for all the channels, the HL2.0 firmware sends a
chan_info_event with COMPLETE flag set to indicate the completion
of the channel info event.
The firmware does not indicate this behavior with any service bitmap
and hence a new firmware feature flag is used to handle the modified
parsing of the channel info events, in the host driver, for the
firmware which sends single channel info event per scanned channel.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Co-developed-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value from devm_memremap() is not checked correctly.
The test is done against a wrong variable. This patch fix it.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ar->target_version is same for QCA99x0, QCA4019, QCA9888
and QCA9984, this ended up in assigning the wrong hw_mem_layouts.
This patch adds additional hw_rev check to assign correct
hw_mem_layouts.
Tested on:
QCA4019 firmware 10.4-3.2.1.1-00017
QCA9984 firmware 10.4-3.5.3-00057
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware crash memory dump support for QCA4019.
Tested on:
QCA4019 firmware 10.4-3.2.1.1-00017
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds the tx statistics pkts/bytes dump
in rate table format.
Dump format table is similar to http://mcsindex.com/
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
command:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the WCN3990 firmware becomes unavailable,
the host driver receives a FW down indication, post
which all the direct hardware register access should
be avoided, in order to prevent improper behavior in
the host driver.
Set the crash_flush flag when the host driver receives
a FW_DOWN_IND via qmi, in order to stop the untimely
hardware register access. Also handle the case, where
we need to do core register only for the first FW_READY
indication, which is when we initialize the host driver.
All the subsequent FW_READY indication will be received
in subsystem recovery case and we only need to do the
restart work. The state of driver is maintained using
flags to distinguish between first and subsequent FW_READY
indication received.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WCN3990 QMI client handshakes for Q6 integrated WLAN connectivity
subsystem. This layer is responsible for communicating qmi control
messages to wifi fw QMI service using QMI messaging protocol.
Qualcomm MSM Interface(QMI) is a messaging format used to communicate
between components running between remote processors with underlying
transport layer based on integrated chipset(shared memory) or
discrete chipset(PCI/USB/SDIO/UART).
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add debug mask to control debug info of ath10k qmi
messaging layer.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support to create the boardname for non-bmi targets
like WCN3990, which uses qmi for bdf download. This
boardname is used to parse the board data from board-2.bin.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We added an unnecessary condition here in commit a904417fc8 ("ath10k:
add extended per sta tx statistics support"). "legacy_rate_idx" is a u8
so it can't be negative. The caller doesn't pass negatives either. I
have deleted this code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_pci_diag_write_mem may allocate big size of the dma memory
based on the parameter nbytes. Take firmware diag download as
example, the biggest size is about 500K. In some systems, the
allocation is likely to fail because it can't acquire such a large
contiguous dma memory.
The fix is to allocate a small size dma memory. In the loop,
driver copies the data to the allocated dma memory and writes to
the destination until all the data is written.
Tested with QCA6174 PCI with
firmware-6.bin_WLAN.RM.4.4.1-00119-QCARMSWP-1, this also affects
QCA9377 PCI.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chomium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the noisy environment, if there are packets in the queue and can't
send out, the suspend timing will be more than 5 seconds due to the wait,
flush the queue to optimize the suspend timing, and let the upper layer to
retry the packets after resume.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI.
It's not a regression with new firmware releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to compare *ps_state_enable* with < 0 because
such variable is of type u8 (8 bits, unsigned), making it
impossible to hold a negative value.
Fix this by removing such comparison.
Addresses-Coverity-ID: 1473921 ("Unsigned compared against 0")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the error handling for the call to function
ath10k_get_legacy_rate_idx() doesn't work because
*rate_idx* is of type u8 (8 bits, unsigned), which
makes it impossible for it to hold a value less
than 0.
Fix this by changing the type of variable *rate_idx*
to s8 (8 bits, signed).
Addresses-Coverity-ID: 1473914 ("Unsigned compared against 0")
Fixes: 0189dbd71c ("ath10k: get the legacy rate index to update the txrate table")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adding WMI service check for management tx ack rssi support; this is
done to maintain common avg ack signal in user level for both data
and management tx ack packet.
Tested on QCA4019(fw version-10.4-3.2.1-00063).
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For WoWLAN support it is expected to support wake up based on discovery of
one or more known SSIDs. This is the WIPHY_WOWLAN_NET_DETECT feature,
which shows up as an NL80211 feature flag.
This shows up in 'iw phy' as:
WoWLAN support:
* wake up on network detection, up to 16 match sets
And it can be enabled with command:
iw phy0 wowlan enable net-detect interval 5000 delay 30 freqs 2412 matches ssid foo
Firmware will do scan by the configured parameters after suspend and
wakeup if it found matched SSIDs. Tested with QCA6174 hw3.0 with
firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[kvalo@codeaurora.org: fix lots of endian bugs, whitespace, commit log and style cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the wmi command for setting probe request
oui, needed for mac randomization, is sent during
the mac register. At this time, during the driver
init the wmi has already been detached. This can
cause unexpected behavior since the firmware is
already down and the wmi has been detached.
Send the wmi command for setting probe request
oui during the driver start. This will make sure
that the firmware is started and wmi is initialized
before we send this command.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: 60e1d0fb29
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While using 'ath10k_mac_get_rate_hw_value()' to obtain the hw value
from the passed bitrate, there is a chance of out of bound array access
when wrong bitrate is passed. This is fixed by comparing the bitrates
within the correct size of the ath10k_rates array.
Fixes commit f279294e9e ("ath10k: add support for configuring management
packet rate"). Also correction made to some indents used in the above commit.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.20. Major changes:
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
ath10k_hw_diag_fast_download() generally has good boundary checking, but
it misses verifying that the next metadata header actually fits in the
remaining buffer space. Add such a check.
Fixes: 39501ea641 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CE buffers are cleaned up prior to napi disable and this is causing
NULL pointer dereference due to "use after free".
Disable napi before resource cleanup to avoid "use after free".
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is unbalanced napi_{enable,disable}() behavior as they
are being called from hif_snoc_{power_up/stop).
The fix is to call napi_enable() from ath10k_snoc_hif_start()
so that it matches with napi_disable() being called from
ath10k_snoc_hif_stop().
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the latest firmware design, the beacon interval should be
greater than 100 to bring the multiple vaps.
Set beacon_int_min_gcd to 100, when the wmi service
WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT is enabled
in the firmware. If not, beacon_int_min_gcd will be set
to the default value 1.
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00015
Tested in QCA9888 with firmware ver 10.4-3.5.1-0005
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch helps to get the power save state change of each peer
connected to the AP. With WMI_10_4_PEER_STA_PS_STATECHG_EVENTID
event, ps state of each peer is reported to user space via
debugfs.
Use the below command to get the ps state of each sta:
cat /sys/kernel/debug/ieee80211/phyX/netdev::wlanX/stations/
XX:XX:XX:XX:XX:XX/peer_ps_state
If STA is in power save state, we get the peer_ps_state value as 1.
if STA is not in power save state, we get the peer_ps_state value as 0.
If ps_state event is disabled, we get the peer_ps_state value as 2.
We can enable/disable the ps_state events using the debugfs flag
"ps_state_enable"
echo Y > /sys/kernel/debug/ieee80211/phyX/ath10k/ps_state_enable
Y = 1 to enable and Y = 0 to disable
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
This change makes use of WMI_VDEV_PARAM_MGMT_RATE param for configuring the
management packets rate to the firmware.
Chipsets Tested : QCA988X, QCA9887, QCA9984
FW Tested : 10.2.4-1.0-41, 10.4-3.6.104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hw_params value will only be used if it was explicitly set in the
global hw_params array.
This makes it possible to have the num_peers member unset.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 9d5804662c ("ath10k: retrieve MAC address from system
firmware if provided"), we support pulling our MAC address from system
firmware. Along with this, we should admit that it's possible for system
firmware to be screwed up as well, omitting the MAC address there.
Provide a fallback, such that we choose a randomly-generated MAC
address, with the local assignment bit set.
This is not a preferred mode of operation and really should only serve
the purpose of keeping the system chugging along while someone figures
out what's wrong with the system. Grepping through other wireless
drivers shows very similar fallback logic though, so why not?
git grep eth_random_addr drivers/net/wireless/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx_status for management frames is being filled
incorrectly in the flags of skb_cb. This incorrect
flag setting causes the upper layers to consider that
the particular frame was not transmitted properly,
leading to improper behavior.
Set the IEEE80211_TX_STAT_ACK flag in the info flags
of skb_cb, to indicate the successful transmission of
the management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: dc405152bb
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The vdev-start-response message should cause the
completion to fire, even in the error case. Otherwise,
the user still gets no useful information and everything
is blocked until the timeout period.
Add some warning text to print out the invalid status
code to aid debugging, and propagate failure code.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is done in order not to trig the below warning in
ieee80211_rx_napi:
WARN_ON_ONCE(softirq_count() == 0);
ieee80211_rx_napi requires that softirq's are disabled during
execution.
The High latency bus drivers (SDIO and USB) sometimes call the wmi
ep_rx_complete callback from non softirq context, resulting in a trigger
of the above warning.
Calling ieee80211_rx_ni with softirq's already disabled (e.g., from
softirq context) should be safe as the local_bh_disable and
local_bh_enable functions (called from ieee80211_rx_ni) are fully
reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Special HTT RX handling for high latency interfaces.
Since no DMA physical addresses are used in the RX ring
config message (this is not supported by the high latency
devices), no RX ring is allocated.
All RX skb's are allocated by the driver and passed directly
to mac80211 in the HTT RX indication handler.
A nice side effect of this is that no huge buffer will be
allocated with dma_alloc_coherent. On embedded systems with
limited memory resources, the allocation of the RX ring is
prone to fail.
Some tweaks made to "make it work":
Removal of protected bit in 802.11 header frame control field.
The chipset seems to do hw decryption but the frame_control
protected bit is still set.
This is necessary for mac80211 not to drop the frame.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add HTT TX function for HL interfaces.
Intended for SDIO and USB.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Special HTT RX ring config message used by high latency
devices.
The main difference between HL and LL is that HL devices
do not use shared memory between device and host and thus,
no host paddr's are added to the RX config message.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initial (empty) HTT RX ops for high latency devices.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several DMA related functions (such as the dma_map_xxx functions)
are not used with high latency devices and don't need to be invoked
in this case.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch makes sure the value of max_num_peers matches
num_peers in hw_params (if set to a non zero value).
hw_params->num_peers is used in the TLV WMI init command.
If ar->max_num_peers is not set to the same value, there is a risk
that the user creates more peers than the maximum number of peers
supported by the device.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As TARGET_TLV_NUM_TIDS is calculated like this:
#define TARGET_TLV_NUM_TIDS ((TARGET_TLV_NUM_PEERS) * 2)
... it is better to use the per device hw_params.num_peers value in
the TLV init message (if set), rather than using a hard coded value.
This makes the value used in the TLV init message match the hw_param
value.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bus type is used together with the other hw parameters
to find a matching entry in ath10k_hw_params_list for the device.
This is necessary since HL devices can have the same dev_id and
target_version as a corresponding LL device (same chipset) and
yet use a totally different configuration.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add dev_type parameter to struct ath10k_bus_params.
The dev type specifies if the device is a high latency device (usb and
sdio) or low latency device (pci, ahb and snoc)
The setup of high latency chips is sometimes different than
for chips using low latency interfaces.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This struct is used as argument to ath10k_core_register in order to
make it easier to add more bus parameters in the future.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Downloading firmware via BMI protocol takes too long time. For example,
a ~700K bytes firmware takes about 500ms to download via BMI protocol.
This is too long especially in suspend and resume scenario where firmware
is re-downloaded unless WoWLAN is enabled. Downloading firmware via diag CE
can reduce the time to ~40ms for a ~700K bytes firmware binary.
Ath10k driver parses the firmware to segments and downloads the segments
to the specified address directly. If the firmware is compressed or has
unsupported segments, ath10k driver will try BMI download again.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To download firmware via diag interface, driver needs to write the target
memory space below 1M. It means the bit20 should be zero for the converted
address if the target memory space is below 1M. Otherwise, bit20 is one if
the target address is larger or equal to 1M space.
As downloading firmware via diag interface is only required for qca6174
and qca9377, a new specific function is introduced to convert the target
address to ce address: ath10k_pci_qca6174_targ_cpu_to_ce_addri().
This function supports to convert any target address to ce address.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Delay 1ms is too long for both diag read and write operations.
This is observed when writing a big memory buffer to target or
reading a big memory buffer from target. Take writing/reading
512k bytes as example, the delay itself is 256ms as the maximum
length of every write/read is 2k size.
Reduce the delay to 50us for read and write operations.
Take the ath10k_pci_targ_cpu_to_ce_addr() out of loop and put it
in the beginning of the loop for ath10k_pci_diag_read_mem().
The ath10k_pci_targ_cpu_to_ce_addr() is to convert the address
from target cpu's perspective to CE's perspective, so it makes
no sense to convert a CE's perspective address again in the loop.
It's a wrong implementation but happens to work.
If the target address is below 1M space, then the convert in the loop
from the second time becomes wrong because the previously converted address
is larger than 1M. The counterpart ath10k_pci_diag_write_mem() has the
correct implementation.
With this change, ath10k_pci_diage_read_mem() works correctly no matter
the target address is below 1M or above 1M.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Average ack rssi value is weighted average of ack rssi for
no of msdu's has been sent.
This feature is enabled by the host driver if firmware is capable.
After receiving event from host, firmware allocates the necessary
memory to store the ack_rssi for data packets during the init time.
After each successful transmission, If tx completion status is OK
and 24th bit is set in HTT message header then host will fetch the
ack_rssi else host can ignore the ack_rssi field.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
array "ctl_power_table" access index "pream" is initialized with -1 and
is raised as a static analysis tool issue.
[drivers\net\wireless\ath\ath10k\wmi.c:4719] ->
[drivers\net\wireless\ath\ath10k\wmi.c:4730]: (error) Array index -1 is
out of bounds.
Since the "pream" index for accessing ctl_power_table array is initialized
with -1, there is a chance of memory access violation for the cases below.
1) wmi_pdev_tpc_final_table_event change frequency is between 2483 and 5180
2) pream_idx is out of the enumeration ranges of wmi_tpc_pream_2ghz,
wmi_tpc_pream_5ghz
Signed-off-by: K.T.VIJAYAKUMAAR <vijay.bvb@samsung.com>
[kvalo@codeaurora.org: clean up the warning message]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds 'tx_stats' in per station debugfs entry.
Use this command to dump tx_stats:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds per station tx statistics support.
Per station tx stats include
- pkts/bytes transmitted at all possible rates(mcs/nss/bw/gi).
- ACK fails count
- ampdu bytes/pkts transmitted at all possible rates(mcs/nss/bw/gi).
- BA fails count
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds debugfs entry to enable/disable extended
tx statistics. Extended tx statistics are from peer stats
feature.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Get the legacy rate index to update the pkts/bytes counter
against each possible tx rate.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 target uses separate htc service for pktlog.
Add pktlog service request and support for pktlog
rx path handling.
Testing:
Tested on WCN3990 and QCA6174 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Existing copy engine interrupt enable logic assumes that last
CE is using polling mode and due to this interrupt for last copy engine
are always disabled. WCN3990 uses last CE for pktlog and
interrupt remains disabled with existing logic.
To mitigate this issue, introduce CE_ATTR_POLL flag and control
the interrupt based on the flag which can be set in ce_attr.
Testing:
Tested on WCN3990 and QCA6174 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support dual-band variant of QCA9984, new extended board data (eBDF)
is introduced since existing board data ran out of space.
Below is the brief implementation & design detail,
----------------------------------------------------
1. New OTP changes to inform eBDF support in existing OTP download to
fetch board ID and chip ID. This is backward compatible and older
card sends 0 by default for eBDF support bit (bit 18 of OTP response) we
check in ath10k driver.
2. If eBDF is supported, then we need to fetch eBDF ID which is bundled
in downloaded board data. So again OTP is executed for knowing the eBDF ID.
This is done once we set 'board_data_initialized' bit. If eBDF ID
returned is zero, we continue booting with previous board data downloaded.
3. Based on the eBDF ID fetched, ath10k driver tries to download the
extended board data to a new offset ahead of already downloaded board
data address.
4. A new BD IE type, ATH10K_BD_IE_BOARD_EXT is added to differentiate in
bundling eBDF separately in board-2.bin and also to parse through
board bundle for eBDF download in ath10k boot.
5. If eBDF is not present in the board-2.bin bundle or when board ID is
zero, we do a fallback boot to "eboard.bin" in the same QCA9984/hw1.0 dir.
This is same as done to existing "board.bin" if board ID is not present
in board-2.bin bundle.
Current design is that eBDF size will be 2KB and eBDF ID will be
byte value.
Tested the above changes with dual-band variant of QCA9984 card. OTP
update needed for the test will be part of next FW release 10.4-3.6-xxxx.
Below are the logs with ath10k BOOT debugs enabled.
First OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for board id
boot get otp board id result 0x00040400 board_id 1 chip_id 0 ext_bid_support 1
..
Second OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for ext board id
boot get otp ext board id result 0x00000005 ext_board_id 5
boot using eboard name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
..
Extended board data download:
------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 65 62 6f 61 72 64 -id=0,bmi-eboard
00000020: 2d 69 64 3d 35 -id=5
boot found match for name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
boot found eboard data for 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
using board api 2
boot writing ext board data to addr 0xc3000
..
Fallback Extended board data download from "eboard.bin":
---------------------------------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 62 6f 61 72 64 2d -id=0,bmi-board-
00000020: 69 64 3d 31 30 id=10
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-eboard-id=5 from ath10k/QCA9984/hw1.0/board-2.bin
boot fw request 'ath10k/QCA9984/hw1.0/eboard.bin': 0
using board api 1
boot writing ext board data to addr 0xc3000
..
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Just moving functions down in the file, no functional changes.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Both WARN_ON() and WARN_ON_ONCE() already contain unlikely().
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Michal Kazior <michal.kazior@tieto.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: Linux Wireless Mailing List <linux-wireless@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ATH10K_SNOC builds just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there are some tx packets pending in firmware, and then system
enters suspend, firmware will fail for wow enable. This will trigger
mac80211 to stop ath10k and download firmware again, then it is
non-wow suspend.
After add the waiting htt tx complete, then firmware will have some
time window to send or flush the pending tx packets.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI.
It's not a regression with new firmware releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Devices may provide their own MAC address via system firmware (e.g.,
device tree), especially in the case where the device doesn't have a
useful EEPROM on which to store its MAC address (e.g., for integrated
Wifi).
Use the generic device helper to retrieve the MAC address, and (if
present) honor it above the MAC address advertised by the card.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.
There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.
Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When continuously running wifi up/down sequence, the napi poll
can be scheduled after the CE buffers being freed by ath10k_pci_flush
Steps:
In a certain condition, during wifi down below scenario might occur.
ath10k_stop->ath10k_hif_stop->napi_schedule->ath10k_pci_flush->napi_poll(napi_synchronize).
In the above scenario, CE buffer entries will be freed up and become NULL in
ath10k_pci_flush. And the napi_poll has been invoked after the flush process
and it will try to get the skb from the CE buffer entry and perform some action on that.
Since the CE buffer already cleaned by pci flush this action will create NULL
pointer dereference and trigger below kernel panic.
Unable to handle kernel NULL pointer dereference at virtual address 0000005c
PC is at ath10k_pci_htt_rx_cb+0x64/0x3ec [ath10k_pci]
ath10k_pci_htt_rx_cb [ath10k_pci]
ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci]
ath10k_ce_per_engine_service [ath10k_pci]
ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci]
ath10k_ce_per_engine_service_any [ath10k_pci]
ath10k_pci_napi_poll+0x48/0xec [ath10k_pci]
ath10k_pci_napi_poll [ath10k_pci]
net_rx_action+0xac/0x160
net_rx_action
__do_softirq+0xdc/0x208
__do_softirq
irq_exit+0x84/0xe0
irq_exit
__handle_domain_irq+0x80/0xa0
__handle_domain_irq
gic_handle_irq+0x38/0x5c
gic_handle_irq
__irq_usr+0x44/0x60
Tested on QCA4019 and firmware version 10.4.3.2.1.1-00010
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The QCA4019 hw1.0 firmware 10.4-3.2.1-00050 and 10.4-3.5.3-00053 (and most
likely all other) seem to ignore the WMI_CHAN_FLAG_DFS flag during the
scan. This results in transmission (probe requests) on channels which are
not "available" for transmissions.
Since the firmware is closed source and nothing can be done from our side
to fix the problem in it, the driver has to work around this problem. The
WMI_CHAN_FLAG_PASSIVE seems to be interpreted by the firmware to not
scan actively on a channel unless an AP was detected on it. Simple probe
requests will then be transmitted by the STA on the channel.
ath10k must therefore also use this flag when it queues a radar channel for
scanning. This should reduce the chance of an active scan when the channel
might be "unusable" for transmissions.
Fixes: e8a50f8ba4 ("ath10k: introduce DFS implementation")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These were recently introduced and found by checkpatch:
drivers/net/wireless/ath/ath10k/mac.c:6118: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6121: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6124: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Debugfs support to do hardware warm reset with WMI command
WMI_PDEV_PARAM_PDEV_RESET for 10.4 and 10.2.4(if wmi
service is enabled in the firmware for backward compatibility).
This change is purely for debugging purpose when hardware hangs/mutes.
This hardware reset won't affect the connectivity but there will be small
pause in data traffic. Here we are doing BB/MAC level reset and hence
whenever the BB/MAC watchdog is triggered, it does a hardware_chip_reset.
So the target will be in the active state.
Below command used to warm reset the hardware.
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/warm_hw_reset
Tested in QCA988X with firmware ver 10.2.4.70.45
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only code refactoring as all call sites of
ath10k_htt_tx_alloc_msdu_id() take the same lock it can be moved into the
id_get function and the assertion dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointers dev and noa are being assigned but are never used hence they
are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
warning: variable 'noa' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 transmits management frames via WMI
with reference. Currently, with the management
tx completion not being handled, these frames are
not getting freed even after the transmission status
is returned by the firmware.
The transmitted management frames should be freed
when the firmware sends the over-the-air tx status of
the corresponding management frames.
Handle the wmi mgmt tx completion event and free
the corresponding management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx completion of multiple mgmt frames can be bundled
in a single event and sent by the firmware to host, if this
capability is not disabled explicitly by the host. If the host
cannot handle the bundled mgmt tx completion, this capability
support needs to be disabled in the wmi init cmd, sent to the firmware.
Add the host capability indication flag in the wmi ready command,
to let firmware know the features supported by the host driver.
This field is ignored if it is not supported by firmware.
Set the host capability indication flag(i.e. host_capab) to zero,
for disabling the support of bundle mgmt tx completion. This will
indicate the firmware to send completion event for every mgmt tx
completion, instead of bundling them together and sending in a single
event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
Tested on QCA9984 with firmware ver 10.4-3.6-00104
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes a recently added checkpatch warning:
wmi-tlv.c:2703: open brace '{' following function definitions go on the next line
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.19. Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbVgnkAAoJEG4XJFUm622b/DAH/0wmjFQrt1qe/goZ4igZOC5z
TTqPUmv7HO4PbHV6mU5yOFGsRCaGDo1cTyEeoiaYNGH6bQLzzJZeQORkuPQB2q5S
BCwlaET7F2iSmk8hx7eboONyVDm5v2+g6NMHBoikVFz1wZ13kCVa4sHkokUJKYB9
XNw3B2OiarPv9i37DlY3woMlY+6VMQh8J6GiB9cJSa4Xs+7l1aQCdQRP03SabI71
gLBEsW+bEVZrUdJGB5cZ8c6LmukmRQMDKMTQYUna5ZXeW1IX3ejYcQGHzzCZoKJS
LPUmisz4014r5aBzXIu3ctVn4LnVhMS5ms0EH1A6IX3vx8G9QynqH5lm9VQ1OXI=
=kWW/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, packets larger than 1500 will silently be dropped.
Easily reproduced by sending a ping packet with a size larger
than 1500.
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this, when receiving a packet that has this flag set
from firmware, we will read invalid trailer data from the packet,
which will be shown as various errors, e.g. "sdio mbox lookahead
is zero" or "invalid rx packet" or "payload length x exceeds max
htc length".
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All packets in a bundle should use the same endpoint id as the
first lookahead.
This matches how things are done is ath6kl, however,
this patch can theoretically handle several bundles
in ath10k_sdio_mbox_rx_process_packets().
Without this patch we get lots of errors about invalid endpoint id:
ath10k_sdio mmc2:0001:1: invalid endpoint in look-ahead: 224
ath10k_sdio mmc2:0001:1: failed to get pending recv messages: -12
ath10k_sdio mmc2:0001:1: failed to process pending SDIO interrupts: -12
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardcoded values used in ath10k_mac_tx_push_pending and
ath10k_mac_op_wake_tx_queue set an upper limit of how many packets that
can be consumed from the TX queue.
HTC_HOST_MAX_MSG_PER_TX_BUNDLE is a proper name for this constant, as
the value effectively limits the number of messages that can be consumed
in one step. Thus, the value is an upper limit of the number of messages
that can be added to a TX message bundle.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This define is only used for RX bundling so it is more descriptive if
RX is added to the define-name.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Although the TID mask is 0xf, the modulus operation does still not
produce identical results as the bitwise and operator. If the TID is 15, the
modulus operation will "convert" it to 0, whereas the bitwise and will keep it
as 15.
This was found during code review.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While debugging driver crashes related to a buggy firmware
crashing under load, I noticed that ath10k_htt_rx_ring_free
could be called without being under lock. I'm not sure if this
is the root cause of the crash or not, but it seems prudent to
protect it.
Originally tested on 4.16+ kernel with ath10k-ct 10.4 firmware
running on 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running iperf on ath10k SDIO, TX can stop working:
iperf -c 192.168.1.1 -i 1 -t 20 -w 10K
[ 3] 0.0- 1.0 sec 2.00 MBytes 16.8 Mbits/sec
[ 3] 1.0- 2.0 sec 3.12 MBytes 26.2 Mbits/sec
[ 3] 2.0- 3.0 sec 3.25 MBytes 27.3 Mbits/sec
[ 3] 3.0- 4.0 sec 655 KBytes 5.36 Mbits/sec
[ 3] 4.0- 5.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 5.0- 6.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 6.0- 7.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 7.0- 8.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 8.0- 9.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 9.0-10.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 0.0-10.3 sec 9.01 MBytes 7.32 Mbits/sec
There are frames in the ieee80211_txq and there are frames that have
been removed from from this queue, but haven't yet been sent on the wire
(num_pending_tx).
When num_pending_tx reaches max_num_pending_tx, we will stop the queues
by calling ieee80211_stop_queues().
As frames that have previously been sent for transmission
(num_pending_tx) are completed, we will decrease num_pending_tx and wake
the queues by calling ieee80211_wake_queue(). ieee80211_wake_queue()
does not call wake_tx_queue, so we might still have frames in the
queue at this point.
While the queues were stopped, the socket buffer might have filled up,
and in order for user space to write more, we need to free the frames
in the queue, since they are accounted to the socket. In order to free
them, we first need to transmit them.
This problem cannot be reproduced on low-latency devices, e.g. pci,
since they call ath10k_mac_tx_push_pending() from
ath10k_htt_txrx_compl_task(). ath10k_htt_txrx_compl_task() is not called
on high-latency devices.
Fix the problem by calling ath10k_mac_tx_push_pending(), after
processing rx packets, just like for low-latency devices, also in the
SDIO case. Since we are calling ath10k_mac_tx_push_pending() directly,
we also need to export it.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 5ghz channel parameters of TLV target wasn't passed to host, it caused
host can only use lower channels from 36 to 64.
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of Station connects to AP with narrower bandwidth at beginning.
And later the AP changes the bandwidth to winder bandwidth, the AP will
beacon with wider bandwidth IE, eg VHT20->VHT40->VHT80 or VHT40->VHT80.
Since the supported BANDWIDTH will be limited by the PHYMODE, so while
Station receives the bandwidth change request, it will also need to
reconfigure the PHYMODE setting to firmware instead of just configuring
the BANDWIDTH info, otherwise it'll trigger a firmware crash with
non-support bandwidth.
The issue was observed in WLAN.RM.4.4.1-00051-QCARMSWP-1, QCA6174 with
below scenario:
AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz)
disconnect from AP xxx for new auth to yyy
RX ReassocResp from xxx (capab=0x1111 status=0 aid=102)
associated
....
AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz)
AP xxx changed bandwidth, new config is 5200 MHz, width 3 (5210/0 MHz)
....
firmware register dump:
[00]: 0x05030000 0x000015B3 0x00987291 0x00955B31
[04]: 0x00987291 0x00060730 0x00000004 0x00000001
[08]: 0x004089F0 0x00955A00 0x000A0B00 0x00400000
[12]: 0x00000009 0x00000000 0x00952CD0 0x00952CE6
[16]: 0x00952CC4 0x0098E25F 0x00000000 0x0091080D
[20]: 0x40987291 0x0040E7A8 0x00000000 0x0041EE3C
[24]: 0x809ABF05 0x0040E808 0x00000000 0xC0987291
[28]: 0x809A650C 0x0040E948 0x0041FE40 0x004345C4
[32]: 0x809A5C63 0x0040E988 0x0040E9AC 0x0042D1A8
[36]: 0x8091D252 0x0040E9A8 0x00000002 0x00000001
[40]: 0x809FDA9D 0x0040EA58 0x0043D554 0x0042D554
[44]: 0x809F8B22 0x0040EA78 0x0043D554 0x00000001
[48]: 0x80911210 0x0040EAC8 0x00000010 0x004041D0
[52]: 0x80911154 0x0040EB28 0x00400000 0x00000000
[56]: 0x8091122D 0x0040EB48 0x00000000 0x00400600
Reported-by: Rouven Czerwinski <rouven@czerwinskis.de>
Tested-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in wireless-drivers by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.19. Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
Return type of resource init method is not assigned.
Handle resource init failures for graceful exit.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In non-bmi target ex. WCN3990, data calibration
is handled via QMI.
Skip data calibration in debug routine to enable ath10k
debugfs for non bmi targets.
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sort these alphabetically, with local includes in a separate section.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We started using a common CE_ATTR_FLAGS definition, so drop this one.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's easier to violate abstractions and introduce bugs when snoc.h is
including pci.h. Let's not do that.
I'm not extremely familiar with this driver yet, but several of the
shared PCI/SNOC bits seem to be related to the Copy Engine, so move them
to ce.h.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We're 'ath10k_snoc', not 'ath10k_pci'. This probably means we're
accessing junk data in ath10k_snoc_rx_replenish_retry(), unless
'ath10k_snoc' and 'ath10k_pci' happen to have very similar struct
layouts.
Noticed by inspection.
Fixes: d915105231 ("ath10k: add hif rx methods for wcn3990")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_snoc_init()/ath10k_snoc_exit() don't add much value;
module_platform_driver() can remove the boilerplate.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The comments are telling you what the enum could tell you instead.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sizeof(struct ce_desc) should be a copy-paste mistake
just use sizeof(struct ce_desc_64) to avoid mem leak
Fixes: b7ba83f7c4 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warnings:
drivers/net/wireless/ath/ath10k/snoc.c:823:5: warning:
symbol 'ath10k_snoc_get_ce_id_from_irq' was not declared. Should it be static?
drivers/net/wireless/ath/ath10k/snoc.c:871:6: warning:
symbol 'ath10k_snoc_init_napi' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The spectral scan has been always broken on QCA9984 and QCA9888.
Introduce a hardware parameter 'spectral_bin_offset' to resolve this issue for
QCA9984 and QCA9888 chipsets. For other chipsets, the hardware parameter
'spectral_bin_offset' is zero so that existing behaviour is retained as it is.
In QCA9984 and QCA9888 chipsets, hardware param value 'spectral_bin_discard'
is 12 bytes. This 12 bytes is derived as the sum of segment index (4 bytes),
extra bins before the actual data (4 bytes) and extra bins after the actual
data (4 bytes). Always discarding (12 bytes) happens at end of the samples and
incorrect samples got dumped, so that user can find incorrect arrangement
samples in spectral scan dump.
To fix this issue, we have to discard first 8 bytes and last 4 bytes in every
samples, so totally 12 bytes are discarded. In every sample we need to consider
the offset while taking the actual spectral data. For QCA9984, QCA9888 the
offset is 8 bytes (segment index + extra bins before actual data).
Hardware tested: QCA9984 and QCA9888
Firmware tested: 10.4-3.5.3-00053
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The India regulatory domain allows CH 173, so add that to the
available channel list. I verified basic connectivity between
a 9880 and 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently tpc_stats is allocated and is leaked on the return
path if num_tx_chain is greater than WMI_TPC_TX_N_CHAIN. Avoid
this leak by performing the check on num_tx_chain before the
allocation of tpc_stats.
Detected by CoverityScan, CID#1469422 ("Resource Leak")
Fixes: 4b190675ad ("ath10k: fix kernel panic while reading tpc_stats")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced "pass through" with
a proper "fall through" comment, which is what GCC is expecting
to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
In the 10.4-3.6 firmware branch there's a new DFS Host confirmation
feature which is advertised using WMI_SERVICE_HOST_DFS_CHECK_SUPPORT flag.
This new features enables the ath10k host to send information to the
firmware on the specifications of detected radar type. This allows the
firmware to validate if the host's radar pattern detector unit is
operational and check if the radar information shared by host matches
the radar pulses sent as phy error events from firmware. If the check
fails the firmware won't allow use of DFS channels on AP mode when using
FCC regulatory region.
Hence this patch is mandatory when using a firmware from 10.4-3.6 branch.
Else, DFS channels on FCC regions cannot be used.
Supported Chipsets : QCA9984/QCA9888/QCA4019
Firmware Version : 10.4-3.6-00104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enables ath10k/ath9k drivers to collect the specifications of the
radar type once it is detected by the dfs pattern detector unit.
Usage of the collected info is specific to driver implementation.
For example, collected radar info could be used by the host driver
to send to co-processors for additional processing/validation.
Note: 'radar_detector_specs' data containing the specifications of
different radar types which was private within dfs_pattern_detector/
dfs_pri_detector is now shared with drivers as well for making use
of this information.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure channel dwell time from duration of the scan request
received from mac80211 when the duration is non-zero. When the
scan request does not have duration value, use the default ones,
the current implementation.
Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is
advertized.
Supported Chipsets:
-QCA988X/QCA9887 PCI
-QCA99X0/QCA9984/QCA9888/QCA4019 PCI
-QCA6174/QCA9377 PCI/USB/SDIO
-WCN3990 SNOC
Tested on QCA9984 with firmware ver 10.4-3.6-0010
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware crash memory dump support for QCA9888 and QCA99X0.
Tested on:
QCA9888 firmware 10.4-3.5.3-00053
QCA99X0 firmware 10.4.1.00030-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath10k testmode uses request_firmware_direct() in order to avoid
producing firmware load warnings. Disabling the fallback mechanism was a
side effect of disabling warnings.
We now have a new API that allows us to avoid warnings while keeping the
fallback mechanism enabled. So use that instead.
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reduces the unnecessary spew when trying to load optional firmware:
"Direct firmware load for ... failed with error -2"
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the BIT() macro from 'linux/bitops.h' to define the rx desc
bit flags to have consistency with new definitions.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some reason not all entries used ATH10K_FW_DIR so fix that. No functional
changes.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable buf_len and num_vdev_stats are being assigned but never read.
These are redundant and can be remove.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_mac_tx_push_txq returns either a postive integer (length) on
success or a negative error code on error.
The "if (ret) break;" statement will thus always break out of the loop
immediately after ath10k_mac_tx_push_txq has returned (making the loop
pointless).
A side effect of this fix is that we will iterate the queue until
ath10k_mac_tx_push_txq returns -ENOENT. This will make sure the queue is
not added back to ar->txqs when it is empty. This could potentially
improve performance somewhat (I have seen a small improvement with SDIO
devices).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Structure platform_driver does not need to set the owner field, as this
will be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To enable thermal throttling for QCA6174 and QCA9377,
implement gen_pdev_set_quiet_mode for them.
With this change, quiet period for QCA6174/QCA9377 can
be also set/get via debugfs.
Usage:
To set quiet period:
echo <period> > /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period
To get the current quiet period:
cat /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period
This change has been verified with
QCA6174 hw3.2(fw: WLAN_RM.4.4.1-00102-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jump to the correct label in error handling path.
At this point of execution create_singlethread_workqueue() has succeeded,
so it should be properly destroyed.
Jump label was renamed in commit ec2c64e202 ("ath10k: sdio: fix memory
leak for probe allocations").
However, the bug was originally introduced in commit d96db25d20
("ath10k: add initial SDIO support").
Fixes: d96db25d20 ("ath10k: add initial SDIO support")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in ath10k_warn warning message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During write to some of debugfs in ath10k, few variables exposing stack
data when process user input. which leads to possible information leak.
This patch fix this issue by initializing buffer and checks
the return valure of 'simple_write_to_buffer'.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable sta power save in fw for the targets that
supports idle power save. The idle ps enable command
will be ignored by the firmware which does not support
this feature.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SRRI/DRRI are not mapped in the HW Shadow block and can lead
to un-clocked access if common subsystem in the target is
powered down due to idle mode.
To mitigate this problem SRRI/DRRI can be read from
DDR instead of doing an actual hardware read.
Host allocates non cached memory on ddr and configures
the physical address of this memory to the CE hardware.
The hardware updates the RRI on this particular location.
Read SRRI/DRRI from DDR location instead of
direct target read.
Enable retention restore on ddr using hw params to enable
in specific targets.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 needs shadow register write operation support
for copy engine for regular operation in powersave mode.
Add support for copy engine shadow register write in
datapath tx for WCN3990
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3990 supports shadow register for ce write.
Add a hw param for shadow register support.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default ath10k driver enables the support for HW_CHECKSUM
(NETIF_F_HW_CSUM). Since the TCP/UDP checksum calculation is not enabled
in the wcn3990 firmware the checksum is incorrect in the TCP/UDP packets
and all patckets are dropped. But due note that wcn3990 support in
ath10k is still incomplete so this isn't a critical fix (yet).
Enable hw checksum calculations in wcn3990 hardware by
setting the proper flags in msdu descriptor tso flags.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When trying to set wow wakeup patterns it fails with this command:
iw phyxx wowlan enable patterns offset xx+ IP address xx.xx.xx.xx
The reason is that the wow pattern from upper layer is in 802.3 format
for this case, it need to convert it to 802.11 format. The input
offset parameter is used for 802.3, but the actual offset firmware
need depends on rx_decap_mode, so that it needs to be recalculated.
Pattern of 802.3 packet is not same with 802.11 packet. If the
rx_decap_mode is ATH10K_HW_TXRX_NATIVE_WIFI, then firmware will
receive data packet with 802.11 format from hardware.
Tested with QCA6174 hw3.0 with firmware
WLAN.RM.4.4.1-00099-QCARMSWPZ-1, but this will also affect QCA9377.
This has always failed, so it's not a regression with new firmware
releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.
Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW path is mapped incorrectly for the WCN3990
hw version. Fix fw path with correct hw1.0 name.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added for the same reason as the TX wrappers.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These wrappers makes the HTT ops align better with the HIF ops
(where similar wrappers are used).
It also makes it easier for a target to have unsupported ops
(by letting the corresponding function pointer be NULL).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
commit f2593cb1b2 ("ath10k: Search SMBIOS for OEM board file
extension") added a feature to ath10k that allows Board Data File
(BDF) conflicts between multiple devices that use the same device IDs
but have different calibration requirements to be resolved by allowing
a "variant" string to be stored in SMBIOS [and later device tree, added
by commit d06f26c5c8 ("ath10k: search DT for qcom,ath10k-calibration-
variant")] that gets appended to the ID stored in board-2.bin.
This original patch had a regression, however. Namely that devices with
a variant present in SMBIOS that didn't need custom BDFs could no longer
find the default BDF, which has no variant appended. The patch was
reverted and re-applied with a fix for this issue in commit 1657b8f84e
("search SMBIOS for OEM board file extension").
But the fix to fall back to a default BDF introduced another issue: the
driver currently parses IEs in board-2.bin one by one, and for each one
it first checks to see if it matches the ID with the variant appended.
If it doesn't, it checks to see if it matches the "fallback" ID with no
variant. If a matching BDF is found at any point during this search, the
search is terminated and that BDF is used. The issue is that it's very
possible (and is currently the case for board-2.bin files present in the
ath10k-firmware repository) for the default BDF to occur in an earlier
IE than the variant-specific BDF. In this case, the current code will
happily choose the default BDF even though a better-matching BDF is
present later in the file.
This patch fixes the issue by first searching the entire file for the ID
with variant, and searching for the fallback ID only if that search
fails. It also includes some code cleanup in the area, as
ath10k_core_fetch_board_data_api_n() no longer does its own string
mangling to remove the variant from an ID, instead leaving that job to a
new flag passed to ath10k_core_create_board_name().
I've tested this patch on a QCA4019 and verified that the driver behaves
correctly for 1) both fallback and variant BDFs present, 2) only fallback
BDF present, and 3) no matching BDFs present.
Fixes: 1657b8f84e ("ath10k: search SMBIOS for OEM board file extension")
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix a typo in the function ath10k_wmi_set_wmm_param().
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct a minor bug in the commit 0628467f97 ("ath10k: fix
copy engine 5 destination ring stuck") which introduced a change to fix
firmware assert that happens when ring indices of copy engine 5 are stuck
for a specific duration, problem with this fix is that it did not use
ring arithmatic. As a result,firmware asserts did not go away entirely
athough the frequency of occurrence has reduced. Using ring arithmatic
to fix the issue.
Tested on QCA9984(fw version-10.4-3.4-00082).
Fixes: 0628467f97 ("ath10k: fix copy engine 5 destination ring stuck)
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add clock and regulator votes for WCN3990 WLAN
chipset.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 has interrupts per CE and the interrupt summary
is not retained after the interrupt handler has finished
execution. We need to check if we received any
ce in rx and tx completion path.
Generate a interrupt summary with all CE interrupts if
the target does not retain interrupt summary after the
execution of interrupt handler.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3990 does not use bmi.
Add support to get target info from hif ops.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change type of hif sg tx paddr to dma_addr_t for
supporting target having addressing mode greater than
32 bit.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hif rx methods in rx path for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hif tx/tx-complete methods for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hif power-up/power-down methods for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mapping of HTC endpoint services supported
by wcn3990 target to tx/rx pipe.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 target uses 3 Copy engine(CE1/CE9/CE10) in RX path
and CE 11 for pktlog.
Add data path HTC ep services and PKTLOG services for WCN3990.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hif start/stop callback for allocating/freeing buffers
on tx/rx pipe and enabling/disabling the tx/rx pipe
interrupts.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is integrated 802.11ac chipset with SNOC
bus interface. Add snoc layer driver registration
and associated ops.
WCN3990 support is not yet complete as cold-boot
handshake is done using qmi(Qualcomm-MSM-Interface)
and qmi client support will be added once qmi framework
is available.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CE layer is shared between pci and snoc target and results
in duplicate object inclusion if both modules are compiled
together statically and undefined KBUILD_MODNAME if
compiled as module.
Fix this by building ce layer in ath10k core module by
adding ce object inclusion with ATH10K_CE boolean CONFIG.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add support to get RSSI from acknowledgment
frames for transmitted management frames.
hardware_used: QCA4019, QCA9984.
firmware version: 10.4-3.5.3-00052.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These allocations are not freed upon release.
When on it; go for managed resources instead.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
[kvalo: fix two checkpatch warnings]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The way that 'strncat' is used here raised a warning in gcc-8:
drivers/net/wireless/ath/ath10k/wmi.c: In function 'ath10k_wmi_tpc_stats_final_disp_tables':
drivers/net/wireless/ath/ath10k/wmi.c:4649:4: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
Effectively, this is simply a strcat() but the use of strncat() suggests
some form of overflow check. Regardless of whether this might actually
overflow, using strlcat() instead of strncat() avoids the warning and
makes the code more robust.
Fixes: bc64d05220 ("ath10k: debugfs support to get final TPC stats for 10.4 variants")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit "cfg80211: make RATE_INFO_BW_20 the default" changed
the index of RATE_INFO_BW_20, but the updates to ath10k missed
the special bandwidth calculation case in
ath10k_update_per_peer_tx_stats().
This will fix below warning,
WARNING: CPU: 0 PID: 609 at net/wireless/util.c:1254
cfg80211_calculate_bitrate+0x174/0x220
invalid rate bw=1, mcs=9, nss=2
(unwind_backtrace) from
(cfg80211_calculate_bitrate+0x174/0x220)
(cfg80211_calculate_bitrate) from
(nl80211_put_sta_rate+0x44/0x1dc)from
(nl80211_put_sta_rate) from
(nl80211_send_station+0x388/0xaf0)
(nl80211_get_station+0xa8/0xec)
[ end trace da8257d6a850e91a ]
Fixes: 842be75c77 ("cfg80211: make RATE_INFO_BW_20 the default")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes regression caused by 0c317a02ca
("cfg80211: support virtual interfaces with different beacon intervals"),
with this change cfg80211 expects the driver to advertize
'beacon_int_min_gcd' to support different beacon intervals in multivap
scenario. This support is added for, QCA988X/QCA99X0/QCA9984/QCA4019.
Verifed AP + mesh bring up on QCA9984 with beacon interval 100msec and
1000msec respectively.
Frimware: firmware-5.bin_10.4-3.5.3-00053
Fixes: 0c317a02ca ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For WPA encryption, QCA6174 firmware(version: WLAN.RM.4.4) will unblock
data when M4 was sent successfully. For other encryption which didn't need
4-way handshake firmware will unblock the data when peer authorized. Since
TDLS is 3-way handshake host need send authorize cmd to firmware to unblock
data.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QCA9984/QCA99X0/QCA4019 chipsets have 8 memory regions, dump all of them to the
firmware coredump file. Some of the regions need to be read using ioread() so
add new region types for them.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[kvalo: refactoring etc]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As QCA9984 needs two region types refactor the code to make it easier add the
new types. No functional changes.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW has Smart Logging feature enabled by default for detecting failures
and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
EVENT processing yet, suppressing the unknown event ID warning by moving
this under ATH10K_DBG_WMI.
Simulated the same issue by having associated STA powered off when
ping flood was running from AP backbone. This triggerd STA KICKOUT
in AP followed by FATAL CONDITION event 36925.
Issue was reproduced and verified in below DUT
------------------------------------------------
AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware WLAN.TF.2.1-00014-QCARMSWP-1 now supports reading the board ID
information and also required 9 IRAM bank, which older ath10k version
don't have the support will fail to be enabled, so in order to maintain
the backward compatibility, we need to update the FW API to 6.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware of QCA6174/QCA9377 already support the feature, just enable
it to be able to handle the get_temperature command and process the event.
You can read the temperature by using the hwmon interface,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Verified with the following hardware and software combination,
QCA6174, only firmware-4.bin doesn't support this, otherwise all support.
QCA9377, all the firmwares upstreamed support this command
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When attempt to run worker (ath10k_sta_rc_update_wk) after the station object
(ieee80211_sta) delete will trigger the kernel panic.
This problem arise in AP + Mesh configuration, Where the current node AP VAP
and neighbor node mesh VAP MAC address are same. When the current mesh node
try to establish the mesh link with neighbor node, driver peer creation for
the neighbor mesh node fails due to duplication MAC address. Already the AP
VAP created with same MAC address.
It is caused by the following scenario steps.
Steps:
1. In above condition, ath10k driver sta_state callback (ath10k_sta_state)
fails to do the state change for a station from IEEE80211_STA_NOTEXIST
to IEEE80211_STA_NONE due to peer creation fails. Sta_state callback is
called from ieee80211_add_station() to handle the new station
(neighbor mesh node) request from the wpa_supplicant.
2. Concurrently ath10k receive the sta_rc_update callback notification from
the mesh_neighbour_update() to handle the beacon frames of the above
neighbor mesh node. since its atomic callback, ath10k driver queue the
work (ath10k_sta_rc_update_wk) to handle rc update.
3. Due to driver sta_state callback fails (step 1), mac80211 free the station
object.
4. When the worker (ath10k_sta_rc_update_wk) scheduled to run, it will access
the station object which is already deleted. so it will trigger kernel
panic.
Added the peer exist check in sta_rc_update callback before queue the work.
Kernel Panic log:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0204000
[00000000] *pgd=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
CPU: 1 PID: 1833 Comm: kworker/u4:2 Not tainted 3.14.77 #1
task: dcef0000 ti: d72b6000 task.ti: d72b6000
PC is at pwq_activate_delayed_work+0x10/0x40
LR is at pwq_activate_delayed_work+0xc/0x40
pc : [<c023f988>] lr : [<c023f984>] psr: 40000193
sp : d72b7f18 ip : 0000007a fp : d72b6000
r10: 00000000 r9 : dd404414 r8 : d8c31998
r7 : d72b6038 r6 : 00000004 r5 : d4907ec8 r4 : dcee1300
r3 : ffffffe0 r2 : 00000000 r1 : 00000001 r0 : 00000000
Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: 595bc06a DAC: 00000015
...
Process kworker/u4:2 (pid: 1833, stack limit = 0xd72b6238)
Stack: (0xd72b7f18 to 0xd72b8000)
7f00: 00000001 dcee1300
7f20: 00000001 c02410dc d8c31980 dd404400 dd404400 c0242790 d8c31980 00000089
7f40: 00000000 d93e1340 00000000 d8c31980 c0242568 00000000 00000000 00000000
7f60: 00000000 c02474dc 00000000 00000000 000000f8 d8c31980 00000000 00000000
7f80: d72b7f80 d72b7f80 00000000 00000000 d72b7f90 d72b7f90 d72b7fac d93e1340
7fa0: c0247404 00000000 00000000 c0208d20 00000000 00000000 00000000 00000000
7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<c023f988>] (pwq_activate_delayed_work) from [<c02410dc>] (pwq_dec_nr_in_flight+0x58/0xc4)
[<c02410dc>] (pwq_dec_nr_in_flight) from [<c0242790>] (worker_thread+0x228/0x360)
[<c0242790>] (worker_thread) from [<c02474dc>] (kthread+0xd8/0xec)
[<c02474dc>] (kthread) from [<c0208d20>] (ret_from_fork+0x14/0x34)
Code: e92d4038 e1a05000 ebffffbc[69210.619376] SMP: failed to stop secondary CPUs
Rebooting in 3 seconds..
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The skb may be freed in tx completion context before
trace_ath10k_wmi_cmd is called. This can be easily captured when
KASAN(Kernel Address Sanitizer) is enabled. The fix is to move
trace_ath10k_wmi_cmd before the send operation. As the ret has no
meaning in trace_ath10k_wmi_cmd then, so remove this parameter too.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Export the final Transmit Power Control (TPC) value, which is the
minimum of control power and existing TPC value to user space via
a new debugfs file "tpc_stats_final" to help with debugging.
It works with the new wmi cmd and event introduced in 10.4 firmware
branch.
WMI command ID: WMI_PDEV_GET_TPC_TABLE_CMDID
WMI event ID: WMI_PDEV_TPC_TABLE_EVENTID
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
$ cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
TPC config for channel 5180 mode 10
CTL = 0x 0 Reg. Domain = 58
Antenna Gain = 0 Reg. Max Antenna Gain = 0
Power Limit = 60 Reg. Max Power = 60
Num tx chains = 2 Num supported rates = 109
******************* CDD POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
******************* STBC POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
***********************************
TXBF not supported
**********************************
The existing tpc_stats debugfs file provides the dump
which is minimum of target power and regulatory domain.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats
Hardware_used: QCA4019
Firmware version: firmware-5.bin_10.4-3.0-00209
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added per tid sta counters for the following
- Total number MSDUs received from firmware
- Number of MSDUs received with errors like decryption, crc, mic ,etc.
- Number of MSDUs dropped in the driver
- A-MPDU/A-MSDU subframe stats
- Number of MSDUS passed to mac80211
All stats other than A-MPDU stats are only for received data frames.
A-MPDU stats might have stats for management frames when monitor
interface is active where management frames are notified both in wmi
and HTT interfaces.
These per tid stats can be enabled with tid bitmask through a debugfs
like below
echo <tid_bitmask> > /sys/kernel/debug/ieee80211/phyX/ath10k/sta_tid_stats_mask
tid 16 (tid_bitmask 0x10000) is used for non-qos data/management frames
The stats are read from
/sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/<sta_mac>/dump_tid_stats
Sample output:
To enable rx stats for tid 0, 5 and 6,
echo 0x00000061 > /sys/kernel/debug/ieee80211/phy0/ath10k/sta_tid_stats_mask
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan15/stations/8c\:fd\:f0\:0a\:8e\:df/dump_tid_stats
Driver Rx pkt stats per tid, ([tid] count)
------------------------------------------
MSDUs from FW [00] 2567 [05] 3178 [06] 1089
MSDUs unchained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:chained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:filtered [00] 0 [05] 0 [06] 0
MSDUs queued for mac80211 [00] 2567 [05] 3178 [06] 1089
MSDUs with error:fcs_err [00] 0 [05] 0 [06] 2
MSDUs with error:tkip_err [00] 0 [05] 0 [06] 0
MSDUs with error:crypt_err [00] 0 [05] 0 [06] 0
MSDUs with error:peer_idx_inval [00] 0 [05] 0 [06] 0
A-MPDU num subframes upto 10 [00] 2567 [05] 3178 [06] 1087
A-MPDU num subframes 11-20 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 21-30 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 31-40 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 41-50 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 51-60 [00] 0 [05] 0 [06] 0
A-MPDU num subframes >60 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 1 [00] 2567 [05] 3178 [06] 1089
A-MSDU num subframes 2 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 3 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 4 [00] 0 [05] 0 [06] 0
A-MSDU num subframes >4 [00] 0 [05] 0 [06] 0
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends mgmt frames by reference via WMI.
The host dma maps the mgmt frame and sends the physical
address to the firmware in the wmi command. Since the
dma mapping is done in the gen_mgmt_tx and if the wmi
command send fails, the corresponding mgmt frame is
not being dma unmapped.
Fix the missing dma unmapping of mgmt tx frame when
wmi command sending fails for mgmt tx by reference
via WMI. The already exisiting mgmt tx using copy by
value does not need such dma unmapping.
Add a separate wmi-tlv op for mgmt tx via ref, which
takes care of unmapping the dma address, in case of
wmi command sending failure.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preparation for a new QCA9377 firmware release. The new firmware release
requires more IRAM banks, hence update that on ath10k.
The IRAM banks promotion won't break any backwards compatibility, as those IRAM
banks were not getting used in previous firmware releases.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HIF power-on failure is applicable to each underlying
bus type. Fix log message for hif power on failure.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever ath10k firmware discards a packet (HTT_TX_COMPL_STATE_DISCARD
flag), the skb is freed and mac80211 does not get feedback through
ieee80211_tx_status().
Instead, make sure that the IEEE80211_TX_STAT_ACK flag is disabled and
let the packet go through, like ath9k does.
Signed-off-by: Ignacio Nunez Hernanz <nacho.nunez@aoifes.com>
[kvalo@codeaurora.org: rebase patch manually]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some modern Ubiquiti devices contain a rebranded QCA988X rev2 with
a custom Ubiquiti vendor and device id. This patch adds support for
those devices, treating them as a QCA988X v2.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[kvalo@codeaurora.org: rebase, add missing fields in hw_params, fix a long line in pci.c:61]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of DRAM dump for QCA6174 hw3.0/hw3.2 and QCA9377 hw1.1
are less than the actual value, some coredump contents are missed.
To fix it, change the length from 0x90000 to 0xa8000.
Fixes: 703f261dd7 ("ath10k: add memory dump support for QCA6174/QCA9377")
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch found these issues:
drivers/net/wireless/ath/ath10k/ce.h:324: Please use a blank line after function/struct/union/enum declarations
drivers/net/wireless/ath/ath10k/core.c:1321: Please don't use multiple blank lines
drivers/net/wireless/ath/ath10k/htt.h:1859: Please use a blank line after function/struct/union/enum declarations
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable section_table.size is a u32 and so cannot be less than
zero, hence the less than zero check is redundant and can be
removed.
Detected by CoverityScan, CID#1463855 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Validate ie_len after the alignment padding before access the buffer
to avoid potential overflow.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was accidentally left out from the switch statement and target info was not
queried.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@codeaurora.org: add commit log]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function does not exist and thus, the prototype can be removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add memory dump to the firmware crash data file which is provided to user space
via devcoredump interface. This makes it easier for firmware engineers to debug
firmware crashes.
Due to increased memory consumption the memory dump is disabled by default. To
enable it make sure that bit 3 is set in coredump_mask module parameter:
modprobe ath10k_core coredump_mask=0xffffffff
When RAMDUMP is enabled a buffer for the dump is allocated with vmalloc during
device probe. The actual memory layout is different in hardware versions and
the layouts are defined in coredump.c. The memory is split to regions and, to
get even finegrained control of what to copy, the region can split to smaller
sections as not all registers are readable (which could cause the whole system
to stall).
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: refactoring and cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For memory dump support (it consumes quite a lot of memory) we need to control
what is exactly stored to the crash dump. Add a module parameter call
coredump_mask to do that. It's a bit mask of these values:
enum ath10k_fw_crash_dump_type {
ATH10K_FW_CRASH_DUMP_REGISTERS = 0,
ATH10K_FW_CRASH_DUMP_CE_DATA = 1,
ATH10K_FW_CRASH_DUMP_MAX,
};
For example, if we only want to store CE_DATA we would enable bit 2:
modprobe ath10k_core coredump_mask=0x2
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now coredump is totally separate from debug.c and doesn't depend on
CONFIG_ATH10K_DEBUGFS anymore, only on CONFIG_DEV_COREDUMP. Also remove
leftovers from the removed debugfs file support.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation to add RAM dump support. No functional changes, only moving code
and renaming function names.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The fw_crash_dump file was deprecated by commmit 727000e6af ("ath10k: support
dev_coredump for crash dump") in v4.11 in favor of dev_coredump interface,
remove it now for good. Everyone should use dev_coredump now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable TDLS wider bandwidth support for 5GHz based on firmware wmi capabilities.
This patch is required for chipset QCA9888. Tested with firmware version
10.4-3.5.1-00018.
Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HL1.0 firmware is not loaded via bmi. The bmi specific
code should not be executed for HL1.0
Add fw feature flag for non bmi targets and skip the bmi
specific code for non bmi targets.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 is integrated chipset which uses system NOC.
Add SNOC bus type and related definitions.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 CE descriptor uses 64bit address for
src/dst ring buffer. It has extended field for toeplitz
hash result, which is being used for HW assisted
hash results.
To accommodate WCN3990 descriptor, define new CE
descriptor for extended addressing mode and related
methods to handle the descriptor data.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE send and receive API's are using u32 ring address, which
truncates the address for target with 64bit addressing range.
Use dma_addr_t for ce buffers to support target with extended
addressing range.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
paddrs_ring_64 holds the physical device address of the
rx buffers that host SW provides for the MAC HW to fill.
Since this field is used in rx ring setup and rx ring
replenish in rx data path. Define separate methods
for handling 64 bit ring paddr and attach them dynamically
based on target_64bit hw param flag. Use u64 type
while popping paddr from the rx hash table for 64bit target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 uses larger ring size in comparison to existing
ring size value.
Add rx ring size hw param for supporting different rx ring
size across multiple target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target uses 64 bit frags_paddr in htt tx descriptor,
which holds the physical address of SKB fragments in tx data path.
In order to support 64 bit bit frags_paddr in htt tx descriptor, define
htt_data_tx_desc_64 descriptor and ath10k_htt_tx_64 method for handling
tx data path with new descriptor fields.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target uses 64 bit frag descriptor and more
fields in TSO flag.
Add support for 64 bit HTT frag descriptor.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3900 target uses 64bit rx_ring_base_paddr and
fw_idx_shadow_reg_paddr fields in HTT rx ring cfg message.
These address points to the memory region where remote
ring empty buffers are allocated.
In order to add 64 bit htt rx ring cfg, define separate
64 bit htt rx ring cfg message and attach it in runtime
based on target_64bit hw param flag.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target use 64bit msdu address in htt in-order
indication message. Add support for 64 bit msdu address in
HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND message.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 rx descriptor uses different offset of msdu start, msdu end,
ppdu end, rx pkt end and rx frag info.
To accommodate different offsets, define respective fields in
rx descriptor of WCN3990 target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target supports 37-bit addressing mode. In order
to accommodate extended address support, add hw param to
indicate if the target supports addressing above 32-bits.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Variable fc is being assigned but never used, so remove it. Cleans
up the clang warning:
warning: Value stored to 'fc' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add hw params entry for wcn3990 and populate various
target specific values for wcn3990.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The parameter values for skid limit, number of peers and wds
entries values which are sent in wmi init cmd are hardware
specific.
Add support to obtain skid limit, number of peers and wds entries
values from hw params which will have the hw specific values
for these parameters.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HL1.0 firmware branch, used in wcn3990, transmits management
frames by reference over WMI.
Add support for management tx by reference over WMI.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to the limitation of wmi tlv parsing logic, if there are
two parameters in a wmi event with same tlv tag, we can get only
the last value, as it overwrites the prev value of the same tlv tag.
The service ready event in wcn3990 contains two parameters of the
same tag UINT32, due to which the svc bitmap is overwritten with the
DBS support parameter.
Refactor the service ready event parsing to allow parsing two tlv
of the same tag UINT32 for wcn3990.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware branch (used in QCA988X) does not support
HTT_10_4_T2H_MSG_TYPE_PEER_STATS and that's why ath10k does not provide
tranmission rate statistics to user space, instead it just shows
hardcoded 6 Mbit/s. But pktlog firmware facility provides per peer tx
statistics. The firmware sends one pktlog event for every four
PPDUs per peer, which include:
* successful number of packets and bytes transmitted
* number of packets and bytes dropped
* retried number of packets and bytes
* rate info per ppdu
Firmware supports WMI_SERVICE_PEER_STATS, pktlog is enabled through
ATH10K_FLAG_PEER_STATS, which is nowadays enabled by default in ath10k.
This patch does not impact throughput.
Tested on QCA9880 with firmware version 10.2.4.70.48. This should also
work with firmware branch 10.2.4-1.0-00029
Parse peer stats from pktlog packets and update the tx rate information
per STA. This way user space can query about transmit rate with iw:
$iw wlan0 station dump
Station 3c:a9:f4:72:bb:a4 (on wlan1)
inactive time: 8210 ms
rx bytes: 9166
rx packets: 44
tx bytes: 1105
tx packets: 9
tx retries: 0
tx failed: 1
rx drop misc: 3
signal: -75 [-75, -87, -88] dBm
signal avg: -75 [-75, -85, -88] dBm
tx bitrate: 39.0 MBit/s MCS 10
rx bitrate: 26.0 MBit/s MCS 3
rx duration: 23250 us
authorized: yes
authenticated: yes
associated: yes
preamble: short
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 22 seconds
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move pktlog_filter from struct ath10k_debug to struct ath10k
so that pktlog can be enabled even when debugfs is not
enabled, needed to enable peer tx stats for 10.2.4.
No changes in functionality.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove CONFIG_MAC80211_DEBUGFS dependency on ath10k_sta_statistics().
ath10k_sta_statistics() has per sta tx/rx stats and this should not
be dependent on MAC80211_DEBUGFS.
No changes in functionality.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With current NAPI implementation, NAPI poll can deliver more frames
to net core than allotted budget. This may cause warning in napi_poll.
Remaining quota is not accounted, while processing amsdus in
rx_in_ord_ind and rx_ind queue. Adding num_msdus at last can not
prevent delivering more frames to net core. With this change,
all amdus from both in_ord_ind and rx_ind queues are processed and
enqueued into common skb list instead of delivering into mac80211.
Later msdus from common queue are dequeued and delivered depends on
quota availability. This change also simplifies the rx processing in
napi poll routine.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Data packets are not sent by STA in case of STA joined to
non QOS AP (WMM disabled AP). This is happening because of STA
is sending data packets to firmware from host with qos enabled
along with non qos queue value(TID = 16).
Due to qos enabled, firmware is discarding the packet.
This patch fixes this issue by updating the qos based on station
WME capability field if WMM is disabled in AP.
This patch is required by 10.4 family chipsets like
QCA4019/QCA9888/QCA9884/QCA99X0.
Firmware Versoin : 10.4-3.5.1-00018.
For 10.2.4 family chipsets QCA988X/QCA9887 and QCA6174 this patch
has no effect.
Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.4 firmware defines this as a 3-bit field, as does the
mac80211 stack. The 4th bit is defined as CONF_IMPLICIT_BF
at least in the firmware header I have seen. This patch
fixes the ath10k wmi header to match the firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
At the moment, spectral scan support, and with it RELAY, is always enabled
with ATH10K_DEBUGFS. Spectral scan support is currently the only user of
RELAY in ath10k, and it unconditionally reserves a relay channel.
Having debugfs support in ath10k is often useful even on very small
embedded routers, where we'd rather like to avoid the code size and RAM
usage of the relay support. While ath10k-based devices usually have more
resources than ath9k-based ones, it makes sense to keep the configuration
symmetric to ath9k, so the same base kernel without RELAY can be used for
both ath9k and ath10k hardware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dump format uses 64-bit timestamps already, but calling
getnstimeofday() only returns a 32-bit number on 32-bit architectures,
so that will overflow in y2038.
This changes it to use ktime_get_real_ts64() instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle tdls peer events from the target. TDLS events for the peer
could be discover, teardown, etc. As of now, adding the logic to
handle tdls teardown events alone.
Teardown due to peer traffic indication(PTR) timeout is one such
teardown event from the target.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is required to update the teardown state of the peer when
a tdls link with that peer is terminated. This information is
useful for the target to perform some cleanups wrt the tdls peer.
Without proper cleanup, target assumes that the peer is connected and
blocks future connection requests, updating the teardown state of the
peer addresses the problem.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 4ca1807815 ("ath10k: disable wake_tx_queue for older devices")
disables the use of the mac80211 TXQs for some devices because of a theoretical
throughput regression. The original regression report[1] was related to
fq_codel qdisc drop performance, which was fixed in commit 9d18562a22
("fq_codel: add batch ability to fq_codel_drop()"). Since then, we have not
seen the TXQ-related regression, so it should be safe to re-enable TXQs.
[1] http://lists.infradead.org/pipermail/ath10k/2016-April/007266.html
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure 16-byte mic is removed from the rx data packet
tail when CCMP-256, GCMP and GCMP-256 ciphers are used
in raw decap mode. This fixed rx traffic failures in those
ciphers in raw mode. Split the helper returning crypto
tail length into two, one to get the ICV length and other
to get the mic lengh for the cipher to make it clean.
Fixes: 2ea9f12cef ("ath10k: add new cipher suite support")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thorsten reported on <fa6e3ee2-91b5-a54b-afe3-87f30aac7a48@leemhuis.info> that
commit c9353bf483 made ath10k unstable with QCA6174 on his Dell XPS13 (9360)
with an error message:
ath10k_pci 0000:3a:00.0: failed to extract amsdu: -11
It only seemed to happen with certain APs, not all, but when it happened the
only way to get ath10k working was to switch the wifi off and on with a hotkey.
As this commit made things even worse (a warning vs breaking the whole
connection) let's revert the commit for now and while the issue is being fixed.
Link: http://lists.infradead.org/pipermail/ath10k/2017-October/010227.html
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx data frames notified through HTT_T2H_MSG_TYPE_RX_IND and
HTT_T2H_MSG_TYPE_RX_FRAG_IND expect PN/TSC check to be done
on host (mac80211) rather than firmware. Rebuild cipher header
in every received data frames (that are notified through those
HTT interfaces) from the rx_hdr_status tlv available in the
rx descriptor of the first msdu. Skip setting RX_FLAG_IV_STRIPPED
flag for the packets which requires mac80211 PN/TSC check support
and set appropriate RX_FLAG for stripped crypto tail. Hw QCA988X,
QCA9887, QCA99X0, QCA9984, QCA9888 and QCA4019 currently need the
rebuilding of cipher header to perform PN/TSC check for replay
attack.
Please note that removing crypto tail for CCMP-256, GCMP and GCMP-256 ciphers
in raw mode needs to be fixed. Since Rx with these ciphers in raw
mode does not work in the current form even without this patch and
removing crypto tail for these chipers needs clean up, raw mode related
issues in CCMP-256, GCMP and GCMP-256 can be addressed in follow up
patches.
Tested-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Variable val is unsigned, so checking whether it is less than zero is
redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The current firmware 10.4-3.5.1-00035 on QCA9888 supports
TDLS explicit mode, it expects WMI_TDLS_ENABLE_PASSIVE
for tdls setup and WMI_TDLS_DISABLE for tdls teardown.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Do not allow off channel operations like scans/roc when
there are active TDLS sessions.
The Current firmware 10.4-3.5.1-00035 on QCA9888 does not
supports any offchannel operations on active TDLS sessions,
either driver needs to block the offchannel operation requests
or should teardown the TDLS connection.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To be able to use ath10k_mac_tdls_vif_stations_count() in
ath10k_hw_scan() in the following patch, move the functions
earlier in the file.
This commit is pure code move, no functional changes.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Build errors have been reported with CONFIG_PM=n:
drivers/net/wireless/ath/ath10k/pci.c:3416:8: error: implicit
declaration of function 'ath10k_pci_suspend'
[-Werror=implicit-function-declaration]
drivers/net/wireless/ath/ath10k/pci.c:3428:8: error: implicit
declaration of function 'ath10k_pci_resume'
[-Werror=implicit-function-declaration]
These are caused by the combination of the following two commits:
6af1de2e4e ("ath10k: mark PM functions as __maybe_unused")
96378bd2c6 ("ath10k: fix core PCI suspend when WoWLAN is supported but
disabled")
Both build fine on their own.
But now that ath10k_pci_pm_{suspend,resume}() is compiled
unconditionally, we should also compile ath10k_pci_{suspend,resume}()
unconditionally.
And drop the #ifdef around ath10k_pci_hif_{suspend,resume}() too; they
are trivial (empty), so we're not saving much space by compiling them
out. And the alternatives would be to sprinkle more __maybe_unused, or
spread the #ifdef's further.
Build tested with the following combinations:
CONFIG_PM=y && CONFIG_PM_SLEEP=y
CONFIG_PM=y && CONFIG_PM_SLEEP=n
CONFIG_PM=n
Fixes: 96378bd2c6 ("ath10k: fix core PCI suspend when WoWLAN is supported but disabled")
Fixes: 096ad2a15fd8 ("Merge branch 'ath-next'")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.15. Major changes:
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
there it's supported (QCA99x0 and QCA4019)
This way, we can apply the values when the NIC does come up.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99x0 and QCA4019 family chips support CCMP-256, GCMP-128, and
GCMP-256 ciphers in hardware, so advertise support for these. As
firmware does not support group management frame ciphers (BIP),
handle them in software (mac80211).
Reviewed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k host enables power save support in station mode by
default for all firmwares but Power save for station mode still not supported
in some of the firmware versions. Which results in firmware crash while
issueing multiple scan commands.
Fix this problem by introducing new FW feature flag to check power save
support in firmware and then the firmware image can tell to ath10k that power
save mode is not supported in station mode.
Signed-off-by: Venkateswara Naralasetty <vnaralas@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For devices where the FW supports WoWLAN but user-space has not
configured it, we don't do any PCI-specific suspend/resume operations,
because mac80211 doesn't call drv_suspend() when !wowlan. This has
particularly bad effects for some platforms, because we don't stop the
power-save timer, and if this timer goes off after the PCI controller
has suspended the link, Bad Things will happen.
Commit 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
got some of this right, in that it understood there was a problem on
non-WoWLAN firmware. But it forgot the $subject case.
Fix this by moving all the PCI driver suspend/resume logic exclusively
into the driver PM hooks. This shouldn't affect WoWLAN support much
(this just gets executed later on).
I would just as well kill the entirety of ath10k_hif_suspend(), as it's
not even implemented on the USB or SDIO drivers. I expect that we don't
need the callback, except to return "supported" (i.e., 0) or "not
supported" (i.e., -EOPNOTSUPP).
Fixes: 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
Fixes: 77258d409c ("ath10k: enable pci soc powersaving")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Cc: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make them const as they are not modified in the file referencing
them. They are only stored in the const field 'hw_ce_reg' of an ath10k
structure. Also, make the declarations in the header const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When CONFIG_PM_SLEEP is disabled, we get a compile-time
warning:
drivers/net/wireless/ath/ath10k/pci.c:3417:12: error: 'ath10k_pci_pm_resume' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/pci.c:3401:12: error: 'ath10k_pci_pm_suspend' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_suspend(struct device *dev)
Rather than fixing the #ifdef, this just marks both functions
as __maybe_unused, which is a more robust way to do this.
Fixes: 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ACPI will rely on device driver to tell it if the device could support
wakeup function when system in D3 state.
This has caused some platform can't support remote wakeup correctly,
because the ACPI wakeup GPE is not enabled, hence registers the .set_wakeup
callback to handle it if device supports wakeup.
Tested with QCA6174 hw3.0, firmware ('WLAN.RM.4.4.1-00008-QCARMSWP-1')
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The actual PCI suspend/resume in ath10k has been handled in wow.c,
but in the case of the device doesn't support remote wakeup,
the .hif_suspend() and .hif_resume() will never be handled.
ath10k_wow_op_suspend()
{
if (WARN_ON(!test_bit(ATH10K_FW_FEATURE_WOWLAN_SUPPORT,
ar->running_fw->fw_file.fw_features))) {
ret = 1;
goto exit;
}
....
ret = ath10k_hif_suspend(ar);
}
So register the PCI PM core to support the suspend/resume if the device
doesn't support remote wakeup.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In commit 9f5bcfe933 ("ath10k: silence firmware file probing
warnings") the firmware loading was changed from request_firmware() to
request_firmware_direct() to silence some warnings in case it fails.
request_firmware_direct() directly searches in the file system only and
does not send a hotplug event to user space in case it could not find
the firmware directly.
In LEDE we use a user space script to extract the calibration data from
the flash memory which gets triggered by the hotplug event. This way the
firmware gets extracted from some vendor specific partition when the
driver requests this firmware. This mechanism does not work any more
after this change.
Fixes: 9f5bcfe933 ("ath10k: silence firmware file probing warnings")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
irq_wq in struct ath10k_sdio is a remnant from an earlier
version of the sdio patchset.
Its use was removed as a result of Kalle's review, but somehow
the struct member survived.
It is not used and can therefore safely be removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In napi_poll, the budget number is used to control the amount of packets
we should handle per poll to balance the resource in the system.
In the list of the amsdu packets reception, we check if there is budget
count left and handle the complete list of the packets, that it will have
chances the very last list will over the budget leftover.
So adding one more parameter - budget_left, this would help while
traversing the list to avoid handling more than the budget given.
Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Fix-suggested-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Link: https://lkml.kernel.org/r/26670dce-4dd2-f8e4-0e14-90d74257e739@virtuozzo.com
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Each time we get disconnected from AP we get flooded with messages like:
...
ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
<until ratelimit kicks in>
ath10k_warn: 155 callbacks suppressed
...
Use ath10k_dbg() here too.
Signed-off-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI interface for all the firmwares(except QCA6174) does not include the
type of peer(default/bss/tdls) requested during peer creation, therefore
target creates a default peer.
TDLS implementation on 10.4 firmware requires host to configure the
peer type(tdls) for TDLS peers. This patch adds peer type parameter to the
existing WMI interface for peer creation to accommodate this requirement.
Tested this change on QCA9888(10.4-3.5.1-00018) and QCA988x(10.2.4.70.9-2)
with ping tests for AP/STA modes.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds the support of TDLS feature for 10.4 firmware
versions.
A new WMI service is added to advertise the support of TDLS for
10.4 firmwares.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Though there is room to accommodate 512 services in wmi service
ready event, target uses only first 4-bits of each 32-bit word for
advertising wmi services thereby limiting max wmi services to 64.
TDLS implementation for 10.4 firmwares introduces new wmi services by
making use of remaining unused bits of each 32-bit word, therefore the
wmi service mapping in host needs to be extended.
This patch adds the logic to extend the wmi SVCMAP to accommodate new
wmi services.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As suggested by Arnd Bergmann, replace
"while (time_before_...) {}"
with
"do {} while (time_before_...)"
This fixes the following warnings detected by gcc 4.1.2:
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_mbox_rxmsg_pending_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:676: warning: ‘ret’ may be used uninitialized in this function
...
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_irq_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:1331: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipsets like QCA9377 have support for USB so add initial USB bus
support to ath10k. With this patch we have the low level HIF and
HTC protocol working and it's possible to boot the firmware,
but it's still not possible to connect or anything like.
More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k USB support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set the a-mpdu reference number in ath10k to make it accessible in the
receivers radiotap header. Implemented as in ath9k. The reference number is
needed for troubleshooting and research at the receivers site (e.g. to identify
mpdu's that were aggregated in an a-mpdu)
Signed-off-by: Matthias Frei <mf@frei.media>
[kvalo@qca.qualcomm.com: fix checkpatch warning, commit log cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All wmi_services are not printing when we give below command.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services
This patch increases the buffer_len to 8192 to print all the wmi_services.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Copy engine is a host to target communication interface
between wlan firmware and wlan wcn3990 platform driver. Add copy
engine register map for wcn3990 wlan module. This add support
for the copy engine source/destination ring configuration for
wcn3990 chipset.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove bus specific dependencies from CE layer
to have common CE layer across multiple targets.
This is required for adding support for WCN3990
chipset support as WCN3990 chipset uses SNOC
bus interface with Copy Engine endpoint.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 59ae1d127a ("networking: introduce and use skb_put_data()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/wmi.c:3308: code indent should use tabs where possible
Fix that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the following spelling mistakes in messages:
syncronise -> synchronize
unusally -> unusually
addrress -> address
inverval -> interval
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZT/ROAAoJEG4XJFUm622b/IwH+wQtBXP+P57DZ97BdETcZ3Wd
ejm9KKT3IxcP7kzItT9UR1zv7LNx4NgSkJMfhf37jJ1WIuE2fp/ctNv6mz3PvohW
jD1fLynwEMMC7PLHEy5+xGtL61KYc2mtXs/bfLFl94hZUiaocrsBDIT4fXoyIWif
y3MUlBKDbHA27ULRd485C0MRekRSvR/rq6iST4KsIsa8RflJbdH64teTEnQPp4kh
nvhfnaxVEqHK7mYbarC58yYLNOU8gfQXmeeTfd6jhCXRjfEw37IvtNC8BT4B9ZDX
YMZLbkeDSwNGXIH7EIrpGOYHCPh+qsiJ+sx7YodomcJvd1nVrmbuZZt9/EqWXuY=
=Fd/c
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA9888 supports VHT80 with 2x2. But it only support 1x1 with VHT160 or
VHT80+80. Inform userspace and the the QCA firmware about that limitation
whenever VHT80+80 or VHT160 is configured.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz.
First, report this to user-space by setting the max-tx-speed
and max-rx-speed vht capabilities.
Second, if the peer rx-speed is configured, and if we
are in 160 or 80+80 mode, and the peer rx-speed matches
the max speed for 2x2 or 1x1 at 160Mhz (long guard interval),
then use that info to set the peer_bw_rxnss_override appropriately.
Without this, a 9984 firmware will not use 2x2 ratesets when
transmitting to peer (it will be stuck at 1x1), because
the firmware would not have configured the rxnss_override.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params, rename the title]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k firmware doesn't announce its VHT channel width capabilities in
the vht_cap information from the "service ready event" arguments. The
driver must therefore check whether the 160MHz short GI bit is set and
whether the driver still doesn't set the bits for the 160/80+80 MHz
capabilities.
The two bits for the channel width are a two bit integer and not two
separate bits which cannot be parsed without the knowledge of the other
bit. Using IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ (b10..) as a
mask for this task doesn't make any sense. The correct mask for the VHT
channel width should be used instead to make this check more readable.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: separate 160Mhz workaround cleanup, add commit
message]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report per chain RSSI to mac80211.
Signed-off-by: Norik Dzhandzhapanyan <norikd@gmail.com>
[kvalo@qca.qualcomm.com: fix conflicts and style]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define structures for the copy engine ctrl/misc registers,
that includes CE CMD halt, watermark source, watermark destination,
host IE ring, source, destination and dmax ring.
This adds support to avoid the conditional compilation,
code optimization and dynamic configuration of the copy engine
register map for respective hardware bus interface.
Signed-off-by: Sarada Prasanna Garnayak <c_sgarna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The original idea is to limit the maximum TDLS peer link, but the logic
is always false, and never be able to restrict the number of TDLS peer
creation.
Fix the logic here and also move the checking earlier, so that it could
avoid to handle the failure case, e.g disable the tdls peer, delete the
peer and also vdev count cleanup.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0, QCA9888, QCA9984 supports calibration data in
either OTP or DT/pre-cal file. Current ath10k supports
Calibration data from OTP only.
If caldata is loaded from DT/pre-cal file, fetching board id
and applying calibration parameters like tx power gets failed.
error log:
[ 15.733663] ath10k_pci 0000:01:00.0: failed to fetch board file: -2
[ 15.741474] ath10k_pci 0000:01:00.0: could not probe fw (-2)
This patch adds calibration data support from DT/pre-cal
file. Below parameters are used to get board id and
applying calibration parameters from cal data.
EEPROM[OTP] FLASH[DT/pre-cal file]
Cal param 0x700 0x10000
Board id 0x10 0x8000
Tested on QCA9888 with pre-cal file.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k firmware checks nbytes == 0 as part of determining if DMA
has completed successfully. To help make this work more often,
have the driver initialize nbytes to zero when freeing the descriptor
slot.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This lets one have a clue that maybe timeouts are happening
when we just aren't waiting long enough.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When testing a 9888 chipset NIC, I notice it often takes
almost 2 seconds, and then many times OTP fails, probably due
to the two-second timeout.
[ 2269.841842] ath10k_pci 0000:05:00.0: bmi cmd took: 1984 jiffies (HZ: 1000), rv: 0
[ 2273.608185] ath10k_pci 0000:05:00.0: bmi cmd took: 1986 jiffies (HZ: 1000), rv: 0
[ 2277.294732] ath10k_pci 0000:05:00.0: bmi cmd took: 1989 jiffies (HZ: 1000), rv: 0
So, increase the BMI timeout to 3 seconds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit b057886524 ("ath10k: do not use coherent memory for
allocated device memory chunks") in 2015 which converted this allocation from
dma_map_coherent() to kzalloc() / dma_map_single().
The current problem manifests when using later model NICs with larger
(>700KiB) scratch spaces in memory. Although the kzalloc call
succeeds, the software IOMMU TLB code (via dma_map_single()) panics
because it can't find 700KiB of linear physmem bounce buffers for DMA.
Now, this is a bit of a silly failure mode for the dma map API,
but it's what we currently have to play with.
In these cases, doing kzalloc() works fine, but the dma_map_single()
call fails.
After chatting with Linus briefly about this, it indeed should be
using dma_alloc_coherent() for doing larger device memory allocation
that requires some kind of physical address mapping.
You're not supposed to be using kzalloc and dma_map_* calls for
large memory regions, and I'm guessing not for long-held mappings
either. Typically dma mappings should be temporary for DMA,
not long held like these.
Now, since hopefully the major annoying underlying problem has also been
addressed (ie, ath10k is no longer tears down all of these allocations
and reallocates them every time the vdevs are brought down) fragmentation
should stop being such a touchy issue. If it is though, using
dma_alloc_coherent() use gets us access to the CMB APIs too relatively
easily and ideally we would be allocating memory early in boot for
exactly these reasons.
Signed-off-by: Adrian Chadd <adrian@FreeBSD.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA4019 firmware 10.4-3.2.1-00050 reports only HT MCS rates between
0-9. But 802.11n MCS rates can be larger than that. For example a 2x2
device can send with up to MCS 15.
The firmware encodes the higher MCS rates using the NSS field. The actual
calculation is not documented by QCA but it seems like the NSS field can be
mapped for HT rates to following MCS offsets:
* NSS 1: 0
* NSS 2: 8
* NSS 3: 16
* NSS 4: 24
This offset therefore has to be added for HT rates before they are stored
in the rate_info struct.
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The array fields in struct wmi_start_scan_arg that are checked here are
fixed size arrays so they can never be NULL.
Addresses-Coverity-ID: 1260031
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9xxx and QCA61x4/QCA93xx are using different wmi operation, in order
for userspace to differentiate it, appends the wmi_op_version information
alone with the get_version command.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During write to debugfs file simulate_fw_crash, fixed-size local buffer
'buf' is accessed and modified at index 'count-1', where 'count' is the
size of the write (so potentially out of bounds).
This patch fixes this problem.
Signed-off-by: Michael Mera <dev@michaelmera.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipsets like QCA6584 have support for SDIO so add initial SDIO bus support to
ath10k. With this patch we have the low level HTC protocol working and it's
possible to boot the firmware, but it's still not possible to connect or
anything like. More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k SDIO support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@qca.qualcomm.com: refactoring, cleanup, commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since both SDIO based chipsets will use different
firmware from the PCIe and AHB chipsets, the fw file name
must be different depending on bus type.
The new firmware names are:
For PCIe and AHB:
firmware-<api_version>.bin (same as before)
For SDIO:
firmware-sdio-<api_version>.bin
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added support for extended ready message.
The extended ready message contains the maximum bundle
count supported by SDIO chipsets.
It is transmitted by SDIO chipset only and replaces the
"standard" ready message in this case.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Special BMI get target info function for SDIO.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Extra initializations needed by all sdio boards.
Derived from qcacld.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Debug masks for SDIO HIF layer.
Address definitions for SDIO/mbox based chipsets.
Augmented struct host_interest with more members.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Code refactorization:
Moved the code for ep 0 in ath10k_htc_rx_completion_handler
to ath10k_htc_control_rx_complete.
This eases the implementation of SDIO/mbox significantly since
the ep_rx_complete cb is invoked directly from the SDIO/mbox
hif layer.
Since the ath10k_htc_control_rx_complete already is present
(only containing a warning message) there is no reason for not
using it (instead of having a special case for ep 0 in
ath10k_htc_rx_completion_handler).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch moves the HTC ctrl service connect from
htc_wait_target to htc_init.
This is done in order to make sure the htc ctrl service
is setup properly before hif_start is called.
The reason for this is that we want the HTC ctrl service
callback to be initialized before the target sends the
HTC ready message.
The ready message will always be transmitted on endpoint 0
(which is always assigned to the HTC control service) so it
makes more sense if HTC control has been connected before the
ready message is received.
Since the service to pipe mapping is done as a part of
the service connect, the get_default_pipe call is redundant
and was removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The RX trailer parsing is now capable of parsing lookahead reports.
A lookahead contains the first 4 bytes of the next HTC message
(that will be read in the next SDIO read operation).
Lookaheads are used by the SDIO/mbox HIF layer to determine if
the next message is part of a bundle, which endpoint it belongs
to and how long it is.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Changed ath10k_htc_notify_tx_completion and
ath10k_htc_process_trailer from static to non static.
These functions are needed by SDIO/mbox.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This field will need to be used again for HE, so rename it now.
Again, mostly done with this spatch:
@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+cipAAoJEG4XJFUm622b+04H/2u7zhIqv3R5NsmGRlwjKmvd
6us1hcYzUiBW1kBFFtcvokwgqv3Rw/EUi+NYA5UCHgo30HTVJWTqW0q+BUEI7U0X
iwuFdHbs/qjj8hXKgZwaJMVyRhXAbq+iHYaMY5OEDNTRSbxqXA4V69SHGK9vLX0l
KQLJBZX3etnwsyRWrmd4E0roGGfD5tMPpGMUDSlvTPWt0I+1QFUxRI9ohn1fRBpD
p+UHHC+SYF6NzxvfqyPwm6ndb2XOwdAKYljlf4KrBwHtSXvAH8p5EASm4PjGbavY
0mrkv0cb8QOKQNVe9q4B4AmM4iAITZ9i3sQBPJ+EBN2P+kS/lFU5L/+5z3VQjms=
=KTEG
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
-----BEGIN PGP SIGNATURE-----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=f4VT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.12. Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
For QCA6174 hw3.0, since WLAN.RM.4.4-00022-QCARMSWPZ-2, it starts to
support the board ID information from otp, with some devices released on
the market that didn't calibrated with OTP, will have 0 for board ID
information, which cause the backward compatibility issue and was fixed
in commit 'd2e202c06ca4 ("ath10k: ignore configuring the incorrect board_id")'
So bump the fw api version to differentiate the latest firmware support.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
spectral_bin length (number of bins per fft sample) is usually
a value where (2^n = value), n is an integer. All of the QCA99X0
family of chipsets seems to report a spectral_bin length of
2^n + 'm' bytes, where m = 4, 12 based on the chipset. This 'm'
bytes seems to carry some radar related info which is currently
discarded only for 'bin_len = 68' bytes. Extend this discarding of
irrelevant 'bin_len' for QCA9984, QCA9888, IPQ4019 as well by
introducing a hardware parameter 'spectral_bin_discard'. Also
for QCA988X based family of chipsets which doesn't seem to have this
issue and also for some of the hardware which I have not tested
like QCA6174/QCA9377 the existing behaviour is retained as it is.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 'ath10k_ce_alloc_pipe' the compile time sanity check to
ensure that there is sufficient buffers in CE4 for HTT Tx
MSDU descriptors, but this did not take into account of the
case with 'peer flow control' enabled, fix this.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY55+nAAoJEG4XJFUm622bRUAIAJfCM5YFyh9Y/XV147JshdGi
xScDAgwIA1/o+iHfvTsjSH3/uoH3JhsiqfcXN7R80kyvG7HrUeXaebmUDgbBvOOj
FTMuytiD+xkgEKVjWIwtXUYqctyzQ8ofxIQJ2W5E9CbEYAZ43uEcXzdnhBKVaVuY
XPw59MF5vRGDDXTnTf4af4OC+L1QqwUqsyi4j7oMIfexieMGQxQL0JYOyHweCnCV
gMz/kTxAIcmC1yOiunu8VyU4kK8borW36wC7XEE3MOXhqSKnQjyhI/efA76AKX0j
O7sfEKCFlZU1xXQbkB9ecbKc2jyMefiE0gwLWWI5dwKhnUS2qQ6GS8ML+NMfV0g=
=B2X+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate line
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Symbolic permissions 'S_IRUSR' are not preferred.
Consider using octal permissions '0400'.
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate lin
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to fix TPC stats to display the stats
properly. Here cosmetic change has been done to print the
TPC stats for all the cases 1.CDD 2.STBC 3.TXBF
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove obselete Copy Engine comments referring to the function
ath10k_ce_sendlist_send as this function was removed long time back
by the commit 2e761b5a52 ("ath10k: remove ce_sendlist_send").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add an ath10k HTC debug message when insufficient tx credits
are available to send the WMI commands. This is very useful
in debugging issues like 'tx credit starvation' that could
possibly happen with multiclient setup with constant roaming
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It seems set_coverage_class_work is not cancelled anywhere,
though I could not find a crash/warning with this existing
design, its safer to cancel it during stop() and also before
restarting the hardware.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If station advertises diffferent NSS capabilities in Rx_mcs set
of HT and VHT IEs in assoc req, the current NSS computation
logic configures the NSS support only based on Rx_mcs set of
HT capabilities in the driver. This is configuring the station
NSS capabilities incorreclty in the target.
For example, if station advertise Rx_mcs set as 2 spatial streams
in HT capabilities and 1 spatial streams in VHT capabilities in
assoc request, as per current logic we are calculating nss from
HT capabilities and the driver sets peer_num_spatial_streams as
2 for the station which is configured in VHT 1*1.
This patchs fix this issue by calculating the nss from VHT cap if
station supports vht.
Signed-off-by: Venkateswara Rao Naralasetty <c_vnaral@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move NAPI enable to 'ath10k_ahb_hif_start' from
'ath10k_ahb_hif_power_up'. This is to maintain the symmetry
of calling napi_enable() from ath10k_ahb_hif_start() so that it
matches with napi_disable() being called from ath10k_pci_hif_stop().
This change is based on the crash fix from Kalle for PCI interface in
commit 1427228d58 ("ath10k: fix napi crash during rmmod when probe
firmware fails").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check of len > buf_len is redundant as len is initialized
to 0 and buf_len to 4096, so this comparison is always false.
Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix typo (spelling mistake) in wmi.h
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I failed to notice that commit 523f6701db ("ath10k: update available channel
list for 5G radio") added two new warnings:
drivers/net/wireless/ath/ath10k/mac.c:3129:6: warning: symbol 'ath10k_mac_update_channel_list' was not declared. Should it be static?
drivers/net/wireless/ath/ath10k/mac.c:3170: Alignment should match open parenthesis
Fix those.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the 'commit ebee76f7fa ("ath10k: allow setting coverage class")',
it inherits the design and the address offset from ath9k, but the address
is not applicable to QCA6174, which leads to a random crash while doing the
resume() operation, since the set_coverage_class.ops will be called from
ieee80211_reconfig() when resume() (if the wow is not configured).
Fix the incorrect address offset here to avoid the random crash.
Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2.
kvalo: this also seems to fix a regression with firmware restart.
Fixes: ebee76f7fa ("ath10k: allow setting coverage class")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fetch target operating channel during potential radar detection when
the interface is just brought up, but no channel is assigned from
userspace. In this scenario rx_channel may not be having a valid pointer
hence fetch the target operating channel to avoid warnings as below
which can be triggered by the commands with DFS testing over longer run
comamnds:
iw wlan1 set type mesh
ifconfig wlan1 up (valid tgt_oper_chan only)
iw wlan1 cac trigger freq 5260 HT20 (valid rx_channel, tgt_oper_chan)
iw wlan1 cac trigger freq 5280 HT20
iw wlan1 cac trigger freq 5300 HT20
Once the CAC expires, current channel context will be removed and
we are only left with the fallback option of using 'target operating
channel'
Firmware and driver log:
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath: phy1: DFS: radar found on freq=5260: id=5, pri=3151, count=6,
count_false=11
ath: phy1: DFS: radar found on freq=5280: id=1, pri=1351, count=6,
count_false=4
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
Call trace:
WARNING: CPU: 1 PID: 2145 at
backports-20161201-3.14.77-9ab3068/net/wireless/chan.c:265
cfg80211_set_dfs_state+0x3c/0x88 [cfg80211]()
Workqueue: phy1 ieee80211_dfs_radar_detected_work
[mac80211]
[<c0320770>] (warn_slowpath_null) from [<bf79b90c>]
(cfg80211_set_dfs_state+0x3c/0x88 [cfg80211])
[<bf79b90c>] (cfg80211_set_dfs_state [cfg80211]) from
[<bf79697c>] (cfg80211_radar_event+0xc4/0x140 [cfg80211])
[<bf79697c>] (cfg80211_radar_event [cfg80211]) from
[<bf83c058>] (ieee80211_dfs_radar_detected_work+0xa8/0xb4 [mac80211])
[<bf83c058>] (ieee80211_dfs_radar_detected_work
[mac80211]) from [<c0339518>] (process_one_work+0x298/0x4a4)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check on ret for an error is redundant because it is already been
checked for non-zero earlier on and ret is never non-zero at this point.
Fix this by removing the redundant check and error message.
Detected by CoverityScan, CID#1357170 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If a 5 GHz radio is calibrated for operation in both
the low band (channels 36 to 64) and high band(channels 100 to 169),
hardware allows operations in all the listed channels. However,
if the chip has been calibrated only for the low/high band and
a high/low band channel is configured, due to lack of calibration
there will be potentially invalid signal on those non calibrated channels.
To avoid this problem this patch sets IEEE80211_CHAN_DISABLED flag for
those non calibrated channels by using low_5ghz_chan and high_5ghz_chan
values which we get from target through wmi service ready event.
Driver initialized flags are getting re initialized in handle_channel
in cfg80211. So calling the function to disable the non supported channel
from reg_notifier().
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DFS is not enabled in hostapd (ieee80211h=0) DFS channels shall
not be available for use even though the hardware may have the capability
to support DFS. With this configuration (DFS disabled in hostapd) trying to
bring up ath10k device in DFS channel for AP mode fails and trying to
simulate DFS in ath10k debugfs results in a warning in cfg80211 complaining
invalid channel and this should be avoided in the driver itself rather than
false propogating RADAR detection to mac80211/cfg80211. Fix this by
checking for the first vif 'is_started' state(should work for client mode
as well) as all the vifs shall be configured for the same channel
sys/kernel/debug/ieee80211/phy1/ath10k# echo 1 > dfs_simulate_radar
WARNING: at net/wireless/chan.c:265 cfg80211_radar_event+0x24/0x60
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
WARNING: at net/wireless/nl80211.c:2488 nl80211_get_mpath+0x13c/0x4cc
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Doing a channel switch via hostapd_cli seems to update
the new channel context for each VAP's appropriately as below
in 'ath10k_mac_update_vif_chan', hence we can safely suppress the
warning that shows up during this operation and dump the warning only
if no vaps are available for channel switch
hostapd_cli -i wlan0 chan_switch 5 5200
OK
ath10k_pci : mac chanctx switch n_vifs 3 mode 1
ath10k_pci : mac chanctx switch vdev_id 2 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 1 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 0 freq 5180->5200 width 0->0
Call Trace:
WARNING: backports-20161201-3.14.77-9ab3068/drivers/net/wireless/ath/ath10k/mac.c:7126
[<c022f2d4>] (warn_slowpath_null) from [<bf7f150c>]
(ath10k_reconfig_complete+0xe4/0x25c [ath10k_core])
[<bf7f150c>] (ath10k_reconfig_complete [ath10k_core])
[<bf7f35f0>] (ath10k_mac_vif_ap_csa_work+0x214/0x370 [ath10k_core])
[<bf7f38b8>] (ath10k_mac_op_change_chanctx+0x108/0x128 [ath10k_core])
[<bf782ac0>] (ieee80211_recalc_chanctx_min_def+0x30c/0x430 [mac80211])
[<bf7830a4>] (ieee80211_recalc_smps_chanctx+0x2ec/0x840 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context+0x7c/0xf8 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context [mac80211])
[<bf76e5d4>] (ieee80211_csa_finalize_work+0x5c/0x88 [mac80211])
Fixes: d7bf4b4aba ("ath10k: fix ar->rx_channel updating logic")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9377 is the family of QCA61x4 which shared the same procedure
to enable the hardware clock that could improve the firmware download time.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Len Brown reported the system resume time is taking more than 2 seconds in
bug - https://bugzilla.kernel.org/show_bug.cgi?id=185621.
The reason of the 2 seconds is due to the firmware download time.
The chip is booted up in the default reference clock speed to handle the
firmware download to chip memory and advanced to the support higher speed
clock to run the firmware after all. The default reference clock in the
hardware is slow so that the firmware download time is taking up to 2
seconds for a 600KB firmware file.
[76796.349701] ath10k_pci : boot uploading firmware image len 688691
[76798.334612] ath10k_pci : htt tx max num pending tx 1056
The resolution here is to enable the higher speed clock if the hardware
supported before the firmware download at BMI stage, so that the hardware
can handle the firmare download in a more efficient way. This can help to
improve the firmware download time from 2 seconds to around 500ms for the
same 600KB firmware file.
[322858.577919] ath10k_pci boot uploading firmware image len 688691
[322859.093094] ath10k_pci htt tx max num pending tx 1056
The steps to advance to the higher speed clock is very hardware specific,
so adding the hardware ops for the hardware that can support this.
Reported-by: Len Brown <lenb@kernel.org>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature
wholesale in all mac80211-based drivers that do not set the
IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will
be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and
will detect when the thresholds set by
ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few)
drivers need code to enable the firmware to monitor the thresholds.
This is mostly only compile-tested.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified, among others, by device and sybsystem ids.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
To solve the issue QCA uses SMBIOS type 0xF8 to store Board Data File Name
Extension to specify the extension/variant name. The driver will take the
extension suffix into consideration and will load the right (non-default)
board data file if necessary.
If it is unnecessary to use extension board data file, please leave the
SMBIOS field blank and default configuration will be used.
Example:
If a default board data file for a specific board is identified by a string
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310"
then the OEM specific data file, if used, could be identified by variant
suffix:
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310,variant=DE_1AB"
If board data file name extension is set but board-2.bin does not contain
board data file for the variant, the driver will fallback to the default
board data file not to break backward compatibility.
This was first applied in commit f2593cb1b2 ("ath10k: Search SMBIOS for OEM
board file extension") but later reverted in commit 005c3490e9 ("Revert
"ath10k: Search SMBIOS for OEM board file extension"". This patch is now
otherwise the same as commit f2593cb1b2 except the regression fixed.
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit f2593cb1b2.
Paul reported that this patch with older board-2.bin ath10k initialisation
fails on Dell XPS 13:
ath10k_pci 0000:3a:00.0: failed to fetch board data for bus=pci,vendor=168c,
device=003e,subsystem-vendor=1a56,subsystem-device=1535,variant=RV_0520 from
ath10k/QCA6174/hw3.0/board-2.bin
The reason is that the older board-2.bin does not have the variant version of
the image name and ath10k does not fallback to the older naming scheme.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=185621#c9
Fixes: f2593cb1b2 ("ath10k: Search SMBIOS for OEM board file extension")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variant[] string will be valid only if the bdf_ext is set.
The string memory needs to be null-terminated to avoid the undefined garbage
appended by the subsequent board file name creation.
ath10k_pci 0000:04:00.0: failed to fetch board data for
"bus=pci,vendor=168c,device=003e,subsystem-vendor=168c,subsystem-device=3363��P�����"
from ath10k/QCA6174/hw3.0/board-2.bin
Fixes: f2593cb1b2 ("ath10k: Search SMBIOS for OEM board file extension")
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k unncessarily warns about board id not available from OTP:
ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
ath10k_pci 0000:02:00.0: firmware ver 10.2.4.70.9-2 api 5 features no-p2p,raw-mode crc32 b8d50af5
ath10k_pci 0000:02:00.0: board id is not exist in otp, ignore it
ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
But not all boards have the board id in OTP so this is not a problem and no
need to confuse the user with that info. So this can be safely changed to a
debug message.
Also fix grammar in the debug message.
Fixes: d2e202c06c ("ath10k: ignore configuring the incorrect board_id")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware files are versioned to prevent older
driver instances to load unsupported firmware
blobs. This is reflected with a fallback logic
which attempts to load several firmware files.
This however produced a lot of unnecessary
warnings sometimes confusing users and leading
them to rename firmware files making things even
more confusing.
Hence use request_firmware_direct() which does not
produce extra warnings. This shouldn't really
break anything because most modern systems don't
rely on udev/hotplug helpers to load firmware
files anymore. For example it was confirmed that
LEDE does not user helper.
This also fixes a 60 second delay per _each_
unexistent firmware/calibration file with distros
which have CONFIG_FW_LOADER_USER_HELPER_FALLBACK
enabled, RHEL being a notable example. Using
ath10k with firmware-2.bin this might end up
into a five minute delay in boot.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[kvalo@qca.qualcomm.com: add more info to the commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This way user has a better idea what file exactly is missing.
This is needed when we switch to using request_firmware_direct() which doesn't
print any errors anymore.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to handle minimum and maximum firmware API numbers convert
the firmware fetch functionality to a loop. If no firmware image is found print
an error with minimum and maximum API numbers and the name of firmware
directory. This is needed when we switch to using request_firmware_direct()
which doesn't print any errors anymore.
Also add a new function for creating the fw file name dynamically which makes it
easier to add new bus support, for example SDIO and USB, later.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@qca.qualcomm.com: remove sdio/usb part, new error message, clarify commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes the below crash when ath10k probe firmware fails, NAPI polling tries
to access a rx ring resource which was never allocated. An easy way to
reproduce this is easy to remove all the firmware files, load ath10k modules
and ath10k will crash when calling 'rmmod ath10k_pci'. The fix is to call
napi_enable() from ath10k_pci_hif_start() so that it matches with
napi_disable() being called from ath10k_pci_hif_stop().
Big thanks to Mohammed Shafi Shajakhan who debugged this and provided first
version of the fix. In this patch I just fix the actual problem in pci.c
instead of having a workaround in core.c.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: __ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
__ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
Call Trace:
[<ffffffffa113ec62>] ath10k_htt_rx_msdu_buff_replenish+0x42/0x90
[ath10k_core]
[<ffffffffa113f393>] ath10k_htt_txrx_compl_task+0x433/0x17d0
[ath10k_core]
[<ffffffff8114406d>] ? __wake_up_common+0x4d/0x80
[<ffffffff811349ec>] ? cpu_load_update+0xdc/0x150
[<ffffffffa119301d>] ? ath10k_pci_read32+0xd/0x10 [ath10k_pci]
[<ffffffffa1195b17>] ath10k_pci_napi_poll+0x47/0x110 [ath10k_pci]
[<ffffffff817863af>] net_rx_action+0x20f/0x370
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: 3c97f5de1f ("ath10k: implement NAPI support")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I wanted to take a look and it's apparently in other header
Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cleanup to consolidate type used for len variables
Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
it adds unnecessary level of indirection, while we just access structure
field
Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is necessary so that - if ath10k is the only driver using
dev_coredump*() - the functionality is built into the kernel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove redundant semicolon after switch statement.
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch provides support to get per peer tids log.
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/
XX:XX/peer_debug_trigger
These logs will be the part of FWLOGS which we collect the logs
via tracing interface. Here we will get the peer tigd logs only
once(not repeatedly) when we write 1 to the debugfs file.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:1593: Statements should start on a tabstop
drivers/net/wireless/ath/ath10k/ce.c:962: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name
drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1639: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/net/wireless/ath/ath10k/htt.h:1660: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYkafBAAoJEG4XJFUm622b0EAH/3mFY0WDfdR/Ych29HX1M/Ao
Bd5gQfKzHS8ANR56qqmxEbpLdBnBa8iNC0IS4RFsWVv6qMoEEOHDLeY5W9XsomWK
i45fQN2XIdjBUOyDXUjsyz006cMe79VzRvFf9gfSekP8i8BCWQzyYC8VKt/F+6Sh
yo9yA4Yv3zA3mA3yRKtxSjLm/6xUXCFVNshKGT0rXc/oEfIN6OnIC1k0p0xw2hhl
GyLN6PSGOqcJc91+IoGOg4TaHzPdWJcWatuxGdQn8gKSDg0+gXaNh9Gtf4H/ojqp
Fwt2Ckk5mgJYk/2TAuFRpRXNMTJznUhp4Tjp2AE7EVM0f5JujUbQuPblOVfLIYk=
=vKKN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified, among others, by device and sybsystem ids.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
To solve the issue QCA uses SMBIOS type 0xF8 to store Board Data File Name
Extension to specify the extension/variant name. The driver will take the
extension suffix into consideration and will load the right (non-default)
board data file if necessary.
If it is unnecessary to use extension board data file, please leave the
SMBIOS field blank and default configuration will be used.
Example:
If a default board data file for a specific board is identified by a string
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310"
then the OEM specific data file, if used, could be identified by variant
suffix:
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310,variant=DE_1AB"
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CORE_CTRL_ADDRESS is offset in register address space, it does not
make sense to OR it to derive the final address. It looks like its
a typo, so fix it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
use dma_zalloc_coherent() instead of dma_alloc_coherent and memset().
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
DIAG_TRANSFER_LIMIT is redefined with same value and comments
just below this entry, remove this duplicate entry.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not clearing the previous tx bit rate status
results in a ambigous tx bit rate reporting to
mac80211/cfg80211, for example the previous bit
rate status would have been marked as legacy rate
, while the current rate would have been an HT/VHT
rate with the tx bit rate flags set and this results
in exporting tx bitrate as legacy rate but with HT/VHT
rate flags set, fix this by clearing the tx bitrate
status for each event. This also fixes the below
warning when we do:
iw dev wlan#N station dump
WARNING: net/wireless/util.c:1222 cfg80211
[<c022f104>] (warn_slowpath_null) from [<bf3b9adc>]
(cfg80211_calculate_bitrate+0x110/0x1f4 [cfg80211])
[<bf3b9adc>] (cfg80211_calculate_bitrate [cfg80211]) from
[<bf3dcd54>] (nl80211_put_sta_rate+0x44/0x1dc [cfg80211])
[<bf3dcd54>] (nl80211_put_sta_rate [cfg80211]) from
[<bf3cbc34>] (nl80211_set_interface+0x724/0xd70 [cfg80211])
[<bf3cbc34>] (nl80211_set_interface [cfg80211]) from
[<bf3d0a18>] (nl80211_dump_station+0xdc/0x100 [cfg80211])
[<bf3d0a18>] (nl80211_dump_station [cfg80211])
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Station pointers are RCU protected so driver must
be extra careful if it tries to store them
internally for later use outside of the RCU
section it obtained it in.
It was possible for station teardown to race with
some htt events. The possible outcome could be a
use-after-free and a crash.
Only peer-flow-control capable firmware was
affected (so hardware-wise qca99x0 and qca4019).
This could be done in sta_state() itself via
explicit synchronize_net() call but there's
already a convenient sta_pre_rcu_remove() op that
can be hooked up to avoid extra rcu stall.
The peer->sta pointer itself can't be set to
NULL/ERR_PTR because it is later used in
sta_state() for extra sanity checks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
-----BEGIN PGP SIGNATURE-----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=UToW
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx legacy rate is reported 10 fold, as below
iw dev wlan#N station dump | grep "tx bitrate"
tx bitrate: 240.0 MBit/s
This is because by mistake we multiply by the hardware reported
rate twice by 10, fix this.
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In countries where basic operation of channel 169 is allowed,
this fixes the below WARN_ON_ONCE in Rx and fixes the station
connectivity failure in channel 169 as the packet is dropped
in the driver as the current check limits to channel 165. As of
now all the packets beyond channel 165 is dropped, fix this
by extending the range to channel 169.
Call trace:
drivers/net/wireless/ath/ath10k/wmi.c:1505
ath10k_wmi_event_mgmt_rx+0x278/0x440 [ath10k_core]()
Call Trace:
[<c158f812>] ? printk+0x2d/0x2f
[<c105a182>] warn_slowpath_common+0x72/0xa0
[<f8b67b58>] ? ath10k_wmi_event_mgmt_rx+0x278/0x440
[<f8b67b58>] ? ath10k_wmi_event_mgmt_rx+0x278/0x440
[<c105a1d2>] warn_slowpath_null+0x22/0x30
[<f8b67b58>] ath10k_wmi_event_mgmt_rx+0x278/0x440
[<f8b0e72b>] ? ath10k_pci_sleep+0x8b/0xb0 [ath10k_pci]
[<f8b6ac63>] ath10k_wmi_10_2_op_rx+0xf3/0x3b0
[<f8b6495e>] ath10k_wmi_process_rx+0x1e/0x60
[<f8b5f077>] ath10k_htc_rx_completion_handler+0x347/0x4d0 [ath10k_core]
[<f8b11dc3>] ? ath10k_ce_completed_recv_next+0x53/0x70 [ath10k_pci]
[<f8b0f921>] ath10k_pci_ce_recv_data+0x171/0x1d0 [ath10k_pci]
[<f8b0ec69>] ? ath10k_pci_write32+0x39/0x80 [ath10k_pci]
[<f8b120bc>] ath10k_ce_per_engine_service+0x5c/0xa0 [ath10k_pci]
[<f8b1215f>] ath10k_ce_per_engine_service_any+0x5f/0x70 [ath10k_pci]
[<c1060dc0>] ? local_bh_enable_ip+0x90/0x90
[<f8b1048b>] ath10k_pci_tasklet+0x1b/0x50 [ath10k_pci]
Fixes: 34c30b0a5e ("ath10k: enable advertising support for channel 169, 5Ghz")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.4 firmware adds extended peer information to the
firmware's statistics payload. This additional info is
stored as a separate data field and the elements are
stored in their own "peers_extd" list.
These elements can pile up in the same way as the peer
information elements. This is because the
ath10k_wmi_10_4_op_pull_fw_stats() function tries to
pull the same amount (num_peer_stats) for every statistic
data unit.
Fixes: 4a49ae94a4 ("ath10k: fix 10.4 extended peer stats update")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds full VHT160 support for QCA9984 chipsets Tested on Netgear
R7800. 80+80 is possible, but disabled so far since it seems to contain
glitches like missing vht station flags (this may be firmware or mac80211
related).
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
[kvalo@qca.qualcomm.com: refactoring and fix few warnings]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When adding VHT160 support to ath10k_peer_assoc_h_phymode() the VHT mode
selection code becomes too complex. Simplify it by refactoring the vht part to
a separate function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simplified transmit credit distribution code somewhat.
Since the WMI control service will get assigned all credits
there is no need for having a credit_allocation array in
struct ath10k_htc.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Removed tx_credits_per_max_message and tx_credit_size
from struct ath10k_htc_ep since they are not used
anywhere in the code.
They are just written, never read.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYalDTAAoJEG4XJFUm622ba2EH/ivoHG9CvmT6HgNw77odDr6b
Zc7plDi2dd9LIzp3rF/9j8Ietfzpu31Pp9Qz0o1Su/s8RJIlXKVF5UeG5IignnEG
02rv7Z+BGPW7SUNDb0cLa27PMYqUAh8vI39sxYSdQ9NQLIlpMLIxxx5iOZyAK5eV
HBRS0pVlSxbAntb1JgWiN/LjjXe/PdhX3CR/b9b468KAcWB6UWj9nXQxFmz7d3uM
dH3buDTgwaq7K24ZAFc1BsD7rgxprpauXxgIMWCKxRERf64WFfYkYdfdCER+PSPH
maV5Te1KzTJBrQHDOPs1ezVe8gDUhb5YE4BJY9SppZpOE1arucq2g3+3obQUeHE=
=DAVq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable advertising support for channel 169, 5Ghz so that
based on the regulatory domain(country code) this channel
shall be active for use. For example in countries like India
this channel shall be available for use with latest regulatory updates
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_mac_tx' does not seems to use the per station table
entry pointer 'sta' (struct ieee80211_sta), hence remove passing
this unused argument
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With command to get board_id from otp, in the case of following
boot get otp board id result 0x00000000 board_id 0 chip_id 0
boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
...
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
ath10k/QCA6174/hw3.0/board-2.bin
The invalid board_id=0 will be used as index to search in the board-2.bin.
Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The txpower is being recalculated when adding interface to make sure
txpower won't overshoot the spec, and when removing the interface,
the txpower should again to be recalculated to restore the correct value
from the active interface list.
Following is one of the scenario
vdev0 is created as STA and connected: txpower:23
vdev1 is created as P2P_DEVICE for control interface: txpower:0
vdev2 is created as p2p go/gc interface: txpower is 21
So the vdev2@txpower:21 will be set to firmware when vdev2 is created.
When we tear down the vdev2, the txpower needs to be recalculated to
re-set it to vdev0@txpower:23 as vdev0/vdev1 are the active interface.
ath10k_pci mac vdev 0 peer create 8c:fd:f0:01:62:98
ath10k_pci mac vdev_id 0 txpower 23
... (adding interface)
ath10k_pci mac vdev create 2 (add interface) type 1 subtype 3
ath10k_pci mac vdev_id 2 txpower 21
ath10k_pci mac txpower 21
... (removing interface)
ath10k_pci mac vdev 2 delete (remove interface)
ath10k_pci vdev 1 txpower 0
ath10k_pci vdev 0 txpower 23
ath10k_pci mac txpower 23
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever firmware crashes, and both CONFIG_ATH10K_DEBUGFS and
CONFIG_ALLOW_DEV_COREDUMP are enabled, dump information about the crash via a
devcoredump device. Dump can be read from userspace for further analysis from:
/sys/class/devcoredump/devcd*/data
As until now we have provided the firmware crash dump file via fw_crash_dump
debugfs keep it still available but deprecate and a warning print that the user
should switch to using dev_coredump.
Future improvement would be not to depend on CONFIG_ATH10K_DEBUGFS, as there
might be systems which want to get the firmware crash dump but not enable
debugfs. How to handle memory consumption is also something which needs to be
taken into account.
Signed-off-by: Arun Khandavalli <akhandav@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: rebase, fixes, improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align it with the cts protection call.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The cts protection vdev parameter, in new QCA9377 TF2.0 firmware,
requires bss peer to be created for the STATION vdev type.
bss peer is being allocated by the firmware after vdev_start/_up commands.
mac80211 may call the cts protection setup at any time, so the
we needs to track the situation and defer the cts configuration
to prevent firmware asserts, like below:
[00]: 0x05020001 0x000015B3 0x0099ACE2 0x00955B31
[04]: 0x0099ACE2 0x00060730 0x00000004 0x00000000
[08]: 0x0044C754 0x00412C10 0x00000000 0x00409C54
[12]: 0x00000009 0x00000000 0x00952F6C 0x00952F77
[16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
[20]: 0x4099ACE2 0x0040E858 0x00421254 0x004127F4
[24]: 0x8099B9B2 0x0040E8B8 0x00000000 0xC099ACE2
[28]: 0x800B75CB 0x0040E8F8 0x00000007 0x00005008
[32]: 0x809B048A 0x0040E958 0x00000010 0x00433B10
[36]: 0x809AFBBC 0x0040E9A8 0x0042BB74 0x0042BBBC
[40]: 0x8091D252 0x0040E9C8 0x0042BBBC 0x00000001
[44]: 0x809FFA45 0x0040EA78 0x0043D3E4 0x0042C2C8
[48]: 0x809FCEF4 0x0040EA98 0x0043D3E4 0x00000001
[52]: 0x80911210 0x0040EAE8 0x00000010 0x004041D0
[56]: 0x80911154 0x0040EB28 0x00400000 0x00000000
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The correct number for QCA9377 chip is 33 VDEVs.
This impacts also QCA6174 chip and it's max VDEV number.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Similarly to QCA6174, QCA9377 requires the CE5 configuration to be
available for other feature. Use the ath10k_pci_override_ce_config()
for it as well.
This is required for TF2.0 firmware. Previous FW revisions were
working fine without this patch.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_htt_tx_free_cont_txbuf' and 'ath10k_htt_tx_free_cont_frag_desc'
have NULL pointer checks to avoid crash if they are called twice
but this is as of now not sufficient as these pointers are not assigned
to NULL once the contiguous DMA memory allocation is freed, fix this.
Though this may not be hit with the explicity check of state variable
'tx_mem_allocated' check, good to have this addressed as well.
Below BUG_ON is hit when the above scenario is simulated
with kernel debugging enabled
page:f6d09a00 count:0 mapcount:-127 mapping: (null)
index:0x0
flags: 0x40000000()
page dumped because: VM_BUG_ON_PAGE(page_ref_count(page)
== 0)
------------[ cut here ]------------
kernel BUG at ./include/linux/mm.h:445!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP is at put_page_testzero.part.88+0xd/0xf
Call Trace:
[<c118a2cc>] __free_pages+0x3c/0x40
[<c118a30e>] free_pages+0x3e/0x50
[<c10222b4>] dma_generic_free_coherent+0x24/0x30
[<f8c1d9a8>] ath10k_htt_tx_free_cont_txbuf+0xf8/0x140
[<f8c1e2a9>] ath10k_htt_tx_destroy+0x29/0xa0
[<f8c143e0>] ath10k_core_destroy+0x60/0x80 [ath10k_core]
[<f8acd7e9>] ath10k_pci_remove+0x79/0xa0 [ath10k_pci]
[<c13ed7a8>] pci_device_remove+0x38/0xb0
[<c14d3492>] __device_release_driver+0x72/0x100
[<c14d36b7>] driver_detach+0x97/0xa0
[<c14d29c0>] bus_remove_driver+0x40/0x80
[<c14d427a>] driver_unregister+0x2a/0x60
[<c13ec768>] pci_unregister_driver+0x18/0x70
[<f8aced4f>] ath10k_pci_exit+0xd/0x2be [ath10k_pci]
[<c1101e78>] SyS_delete_module+0x158/0x210
[<c11b34f1>] ? __might_fault+0x41/0xa0
[<c11b353b>] ? __might_fault+0x8b/0xa0
[<c1001a4b>] do_fast_syscall_32+0x9b/0x1c0
[<c178da34>] sysenter_past_esp+0x45/0x74
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The comment on the name indirection suggested an issue but turned out
to be untrue. Digging in older kernel version showed issue with ipw2x00
but that is no longer true so get rid on the name indirection.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYQGivAAoJEG4XJFUm622bqG0IAJtSGt4Fxv2jL7GPmPpEUtYK
F6G1PCk9LxO44rOZ15E/CT1vPk6Bnwqp9brdngmXwl7jc+jGs4MQN7g6cD4UZgPm
gxjx8cah2HPRVgEE7PeOILthRxwPA+9klycsvwtglkgQ1SpQVmLHDTLpeOAkRluY
olJGINoGHTD6osud6p3oKK+VP891omJvu8TPqRjhrhLhbQTWAuTxl2Gsdye30yag
CsdaEZb9wdUEBoS80EVRwvgBzqrdKU5kGDGbuzytcyrFrRHo4flti1KgxDg3nIpI
jC4Liwg0yE/aYZlfMqi/960rt8AttCJBDt/vwqp0mOE4IwFsE9Yaio6xXUonAC8=
=a6a/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These memory chunks are often used as 'swap' by the NIC,
so it will be both reading and writing to these areas.
This seems to fix errors like this on my x86-64 machine:
kernel: DMAR: DMAR:[DMA Write] Request device [05:00.0] fault addr ff5de000
DMAR:[fault reason 05] PTE Write access is not set
Tested-by: Marek Behun <kabel@blackhole.sk>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With maximum number of vap's configured in a two radio supported
systems of ~256 Mb RAM, doing a continuous wifi down/up and
intermittent traffic streaming from the connected stations results
in failure to allocate contiguous memory for tx buffers. This results
in the disappearance of all VAP's and a manual reboot is needed as
this is not a crash (or) OOM(for OOM killer to be invoked). To address
this allocate contiguous memory for tx buffers one time and re-use them
until the modules are unloaded but this results in a slight increase in
memory footprint of ath10k when the wifi is down, but the modules are
still loaded. Also as of now we use a separate bool 'tx_mem_allocated'
to keep track of the one time memory allocation, as we cannot come up
with something like 'ath10k_tx_{register,unregister}' before
'ath10k_probe_fw' is called as 'ath10k_htt_tx_alloc_cont_frag_desc'
memory allocation is dependent on the hw_param 'continuous_frag_desc'
a) memory footprint of ath10k without the change
lsmod | grep ath10k
ath10k_core 414498 1 ath10k_pci
ath10k_pci 38236 0
b) memory footprint of ath10k with the change
ath10k_core 414980 1 ath10k_pci
ath10k_pci 38236 0
Memory Failure Call trace:
hostapd: page allocation failure: order:6, mode:0xd0
[<c021f150>] (__dma_alloc_buffer.isra.23) from
[<c021f23c>] (__alloc_remap_buffer.isra.26+0x14/0xb8)
[<c021f23c>] (__alloc_remap_buffer.isra.26) from
[<c021f664>] (__dma_alloc+0x224/0x2b8)
[<c021f664>] (__dma_alloc) from [<c021f810>]
(arm_dma_alloc+0x84/0x90)
[<c021f810>] (arm_dma_alloc) from [<bf954764>]
(ath10k_htt_tx_alloc+0xe0/0x2e4 [ath10k_core])
[<bf954764>] (ath10k_htt_tx_alloc [ath10k_core]) from
[<bf94e6ac>] (ath10k_core_start+0x538/0xcf8 [ath10k_core])
[<bf94e6ac>] (ath10k_core_start [ath10k_core]) from
[<bf947eec>] (ath10k_start+0xbc/0x56c [ath10k_core])
[<bf947eec>] (ath10k_start [ath10k_core]) from
[<bf8a7a04>] (drv_start+0x40/0x5c [mac80211])
[<bf8a7a04>] (drv_start [mac80211]) from [<bf8b7cf8>]
(ieee80211_do_open+0x170/0x82c [mac80211])
[<bf8b7cf8>] (ieee80211_do_open [mac80211]) from
[<c056afc8>] (__dev_open+0xa0/0xf4)
[21053.491752] Normal: 641*4kB (UEMR) 505*8kB (UEMR) 330*16kB (UEMR)
126*32kB (UEMR) 762*64kB (UEMR) 237*128kB (UEMR) 1*256kB (M) 0*512kB
0*1024kB 0*2048kB 0*4096kB = 95276kB
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.
During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')
'ath10k_core_restart' -> 'ath10k_hif_stop' (ATH10K_STATE_ON) ->
-> 'ieee80211_restart_hw' -> 'ath10k_start' -> 'ath10k_halt' ->
'ath10k_core_stop' -> 'ath10k_hif_stop' (ATH10K_STATE_RESTARTING)
Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'
Fixes: 3c97f5de1f ("ath10k: implement NAPI support")
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a typo bug in the current implementation of
ath10k_wmi_tlv_op_gen_pdev_set_rd.
The conformance test limits are not set up properly.
The two arguments ctl2g and ctl5g were not used at all.
Instead, the regdomain arguments rd2g and rd5g were used
for the ctl settings as well.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to receive other BSS entries in mesh mode, Monitor vdev
is created whenever filter flag is set with OTHER_BSS. Recently
it is root caused that setting promisc filter for Mesh interface
is causing performance and stability issues. To fix this issue,
firmware will configure appropriate rxfilters by default for mesh
vdev during vdev creation. This change fixes monitor vdev creation
based on firmware IE
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per STA tx bitrate info is filled from peer stats.
Export per sta txrate info to cfg80211/nl80211
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per peer tx stats are part of 'HTT_10_4_T2H_MSG_TYPE_PEER_STATS'
event, Firmware sends one HTT event for every four PPDUs.
HTT payload has success pkts/bytes, failed pkts/bytes, retry
pkts/bytes and rate info per ppdu.
Peer stats are enabled through 'WMI_SERVICE_PEER_STATS',
which are nowadays enabled by default.
Parse peer stats and update the tx rate information per STA.
tx rate, Peer stats are tested on QCA4019 with Firmware version
10.4-3.2.1-00028.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Command structure and event flow doesn't seem to
be any different compared to existing
implementation for other firmware branches.
This patch effectively adds in-driver support for
spectral scanning on QCA61x4 and QCA9377.
Tested QCA9377 w/ WLAN.TF.1.0-00267-1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Neither of these did the right thing:
- get_tsf just returned 0
- set_tsf assumed a simple offset was applied against
get_tsf(), which works, except in the case of
calculating TSF from rx_mactime (actual TSF).
Just remove them for now. We can reimplement set_tsf in
terms of TSF increment/decrement in the future if get_tsf
is ever supported by FW.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current set_tsf is implemented in terms of TSF_INCREMENT
only. Instead support new WMI command TSF_DECREMENT and
export these through offset_tsf. Advantage is we get
more accurate TSF adjustments, and don't calculate wrong
offset in case absolute TSF was calculated from rx_mactime
(actual TSF).
The new WMI command is available in firmware
10.4-3.2.1-00033 for QCA4019 chips. Old drivers on new
firmware or vice versa shouldn't be a problem since
get/set tsf logic was already broken.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Indicate hardware (or firmware) supports that CQM packet-loss report
will be generated based on station kickout algorithm. As of now mac80211
tracks connection loss by missing msdu counts (50) whereas ath10k
firmware tracks them by missing ppdus (+ BAR tries). While firmware is
trying to adapt its rate table, mac80211 might send out low_ack event to
hostapd. This is causing frequent connect and disconnect iteration under
noisy environment or when station is roaming around.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The word "background" contains 10 characters so the third argument of
strncmp() need to be 10 in order to match this prefix correctly.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: 855aed1220 ("ath10k: add spectral scan feature")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove extraneous error message in 'ath10k_htt_tx_alloc_cont_frag_desc'
as the caller 'ath10k_htt_tx_alloc' already dumps a proper error
message
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cleanup 'ath10k_htt_tx_alloc' by introducing the API's
'ath10k_htt_tx_alloc/free_{cont_txbuf, txdone_fifo} and
re-use them whereever needed
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This partially reverts 'commit 2cdce425aa
("ath10k: Fix broken NULL func data frame status for 10.4")'
Unfortunately this breaks sending NULL func and the existing
issue of obtaining proper tx status for NULL function will be
fixed. Also update the comments for feature flag added to be
useless and not working
Fixes: 2cdce425aa "ath10k: Fix broken NULL func data frame status for
10.4"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mac80211 determines whether HW does fragmentation
by checking whether the set_frag_threshold callback is set
or not.
However, some drivers may want to set the HW fragmentation
capability depending on HW generation.
Allow this by checking a HW flag instead of checking the
callback.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
[added the flag to ath10k and wlcore]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
arvifs list is traversed within data_lock spin_lock in tasklet
context to fill channel information from the corresponding vif.
This means any access to arvifs list for add/del operations
should also be protected with the same spin_lock to avoid the
race. Fix this by performing list add/del on arvfis within the
data_lock. This could fix kernel panic something like the below.
LR is at ath10k_htt_rx_pktlog_completion_handler+0x100/0xb6c [ath10k_core]
PC is at ath10k_htt_rx_pktlog_completion_handler+0x1c0/0xb6c [ath10k_core]
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[<bf4857f4>] (ath10k_htt_rx_pktlog_completion_handler+0x2f4/0xb6c [ath10k_core])
[<bf487540>] (ath10k_htt_txrx_compl_task+0x8b4/0x1188 [ath10k_core])
[<c00312d4>] (tasklet_action+0x8c/0xec)
[<c00309a8>] (__do_softirq+0xdc/0x208)
[<c0030d6c>] (irq_exit+0x84/0xe0)
[<c005db04>] (__handle_domain_irq+0x80/0xa0)
[<c00085c4>] (gic_handle_irq+0x38/0x5c)
[<c0009640>] (__irq_svc+0x40/0x74)
(gdb) list *(ath10k_htt_rx_pktlog_completion_handler+0x1c0)
0x136c0 is in ath10k_htt_rx_h_channel (drivers/net/wireless/ath/ath10k/htt_rx.c:769)
764 struct cfg80211_chan_def def;
765
766 lockdep_assert_held(&ar->data_lock);
767
768 list_for_each_entry(arvif, &ar->arvifs, list) {
769 if (arvif->vdev_id == vdev_id &&
770 ath10k_mac_vif_chan(arvif->vif, &def) == 0)
771 return def.chan;
772 }
773
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_htt_rx_h_unchain' needs to be called only if the return
value from 'ath10k_htt_rx_amsdu_pop' is 1('chained msdu's'), this
change makes it more explicit and avoids doing a skb_peek, fetching
rx descriptor pointer, checking rx msdu decap format for the case of
ret = 0 (unchained msdus). Found this change during code walk through,
not sure if this addresses any issue.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 0b8e3c4ca2 ("ath10k: move cal data len to hw_params") broke retrieving
the calibration data from cal_data debugfs file. The length of file was always
zero. The reason is:
static ssize_t ath10k_debug_cal_data_read(struct file *file,
char __user *user_buf,
size_t count, loff_t *ppos)
{
struct ath10k *ar = file->private_data;
void *buf = file->private_data;
This is obviously bogus, private_data cannot contain both struct ath10k and the
buffer. Fix it by caching calibration data to ar->debug.cal_data. This also
allows it to be accessed when the device is not active (interface is down).
The cal_data buffer is fixed size because during the first firmware probe we
don't yet know what will be the lenght of the calibration data. It was simplest
just to use a fixed length. There's a WARN_ON() in
ath10k_debug_cal_data_fetch() if the buffer is too small.
Tested with qca988x and firmware 10.2.4.70.56.
Reported-by: Nikolay Martynov <mar.kolya@gmail.com>
Fixes: 0b8e3c4ca2 ("ath10k: move cal data len to hw_params")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
[kvalo@qca.qualcomm.com: improve commit log and minor other changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Unfortunately ath10k does not generally allow modifying the coverage class
with the stock firmware and Qualcomm has so far refused to implement this
feature so that it can be properly supported in ath10k. If we however know
the registers that need to be modified for proper operation with a higher
coverage class, then we can do these modifications from the driver.
This is a hack and might cause subtle problems but as it's not enabled by
default (only when user space changes the coverage class explicitly) it should
not cause new problems for existing setups. But still this should be considered
as an experimental feature and used with caution.
This patch implements the support for first generation cards (QCA9880, QCA9887
and so on) which are based on a core that is similar to ath9k. The registers
are modified in place and need to be re-written every time the firmware sets
them. To achieve this the register status is verified after certain WMI events
from the firmware.
The coverage class may not be modified temporarily right after the card
re-initializes the registers. This is for example the case during scanning.
Thanks to Sebastian Gottschall <s.gottschall@dd-wrt.com> for initially
working on a userspace support for this. This patch wouldn't have been
possible without this documentation.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This overrides whatever regulatory the device
EEPROM contains and uses what the platform says
instead - in this implementation the ACPI driver.
In case the hint is not programmed or corrupted (0xffff)
the device falls back to the eeprom programmed settings.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
[kvalo@qca.qualcomm.com: remove ifdef, change error handling, change info messages to dbg]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During offchannel scan, iw survey dump shows wrong values.
Fix this by assigning cycle counter wranarround type for
QCA9888 and QCA9884, they share same config with QCA4019.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to get the TPC stats for 10.4 fw variants.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware is running watchdog timer for tracking copy engine ring index
and write index. Whenever both indices are stuck at same location for
given duration, watchdog will be trigger to assert target. While
updating copy engine destination ring write index, driver ensures that
write index will not be same as read index by finding delta between these
two indices (CE_RING_DELTA).
HTT target to host copy engine (CE5) is special case where ring buffers
will be reused and delta check is not applied while updating write index.
In rare scenario, whenever CE5 ring is full, both indices will be referring
same location and this is causing CE ring stuck issue as explained
above. This issue is originally reported on IPQ4019 during long hour stress
testing and during veriwave max clients testsuites. The same issue is
also observed in other chips as well. Fix this by ensuring that write
index is one less than read index which means that full ring is
available for receiving data.
Cc: stable@vger.kernel.org
Tested-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ignore processing further in SWBA event scheduled for a vif, if mac80211
has marked the particular vif for stop beaconing and brought the vdev
down in 'ath10k_control_beaconing'. This should potentially avoid ath10k
warning/error messages while running continuous wifi down/up with max
number of vaps configured. Found this change during code walk through
and going through other beacon configuration related functions in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in function ath10k_ahb_probe() or
ath10k_ahb_resource_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The (1 << x) - 1 trick won't work when you
are trying to fill up all 64 bits, so add special
case for that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: remove the sentence about moving limits]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future)
rx_hdr_status is not padded to align in 4-byte boundary. Define a
new hw_params field to handle different alignment behaviour between
different hw. This patch fixes improper retrieval of rfc1042 header
with QCA4019. This patch along with "ath10k: Properly remove padding
from the start of rx payload" will fix traffic failure in ethernet
decap mode for QCA4019.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since reset_control_get() never returns NULL, we can use IS_ERR()
instead of IS_ERR_OR_NULL(). The return statements can be simpler
as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the managed variant of reset_control_get() to simplify the
failure path and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the managed variant of clk_get() to simplify the failure path
and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Correct some trivial comment typos.
Remove unnecessary parentheses in a long line.
Signed-off-by: Joe Perches <joe@perches.com>
[kvalo@qca.qualcomm.com: drop the change for return]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
hw_4addr_pad was added to handle different types of padding
in 4-address rx frame. But this padding is not very specific
to 4-address, it can happen even with three address + ethernet
decap mode. Since the padding information can be obtained
through Rx desc for QCA99X0 and newer chips, this hw_param
is not needed any more.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA99X0 (QCA99X0, QCA9984, QCA9888 and QCA4019) family chips,
hw adds padding at the begining of the rx payload to make L3
header 4-byte aligned. In the chips doing this type of padding,
the number of bytes padded will be indicated through msdu_end:info1.
Define a hw_rx_desc_ops wrapper to retrieve the number of padded
bytes and use this while doing undecap. This should fix padding
related issues with ethernt decap format with QCA99X0, QCA9984,
QCA9888 and QCA4019 hw.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are slight differences in Rx hw descriptor information
among different chips. So far driver does not use those new
information for any functionalities, but there is one important
information which is available from QCA99X0 onwards to indicate
the number of bytes that hw padded at the begining of the rx
payload and this information is needed to undecap the rx
packet. Add an abstraction for Rx desc to make use of the
new desc information available. The callback that this patch
defines to retrieve the padding bytes will be used in follow-up
patch.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare for rx descriptor abstraction where we'll
be dereferencing ath10k_hw_params member in hw.h. Moreover
hw.h looks more suitable to house ath10k_hw_params definition
than core.h
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Helps to know the sta pointer.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: add %pK and remove the colon]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
IFTYPE_MESH_POINT need to rely on these for accurate path
selection metrics. Other modes will probably also find
them useful. Enabling peer stats has the side effect of
reducing max number of STAs from 128 to 118. There should
be negligible performance impact.
If users really need 128 STAs and don't mind losing out on
peer stats, they can still disable them:
echo 0 > debugfs/ieee80211/phyn/ath10k/peer_stats
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trival fix to remove unused variable ar_pci in ath10k_pci_tx_pipe_cleanup
when building with W=1:
drivers/net/wireless/ath/ath10k/pci.c:1696:21: warning: variable
'ar_pci' set but not used [-Wunused-but-set-variable]
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
caldata is not being free'd on the error exit path, causing
a memory leak and data definitely should not be freed. Free
caldata instead of data.
Thanks to Kalle Valo for spotting that data should not be
free'd.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 3c97f5de1f ("ath10k: implement NAPI support") conflicts with
ath-current. To avoid any merge problems merge ath-current to ath-next already now.
Conflicts:
drivers/net/wireless/ath/ath10k/htt_rx.c
When user requests for survey dump data, driver is providing wrong survey
information. This information we sent is the survey data that we have
collected during previous user request.
This issue occurs because we request survey dump for wrong channel. With
this change, we correctly display the correct and current survey
information to userspace.
Fixes: fa7937e3d5 ("ath10k: update bss channel survey information")
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error assigned does not seems to be used anywhere,
fixes nothing just a small cleanup
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 7a0adc83f3 ("ath10k: improve tx scheduling") is causing
severe throughput drop in multi client mode. This issue is originally
reported in veriwave setup with 50 clients with TCP downlink traffic.
While increasing number of clients, the average throughput drops
gradually. With 50 clients, the combined peak throughput is decreased
to 98 Mbps whereas reverting given commit restored it to 550 Mbps.
Processing txqs for every tx completion is causing overhead. Ideally for
management frame tx completion, pending txqs processing can be avoided.
The change partly reverts the commit "ath10k: improve tx scheduling".
Processing pending txqs after all skbs tx completion will yeild enough
room to burst tx frames.
Fixes: 7a0adc83f3 ("ath10k: improve tx scheduling")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add NAPI support for rx and tx completion. NAPI poll is scheduled
from interrupt handler. The design is as below
- on interrupt
- schedule napi and mask interrupts
- on poll
- process all pipes (no actual Tx/Rx)
- process Rx within budget
- if quota exceeds budget reschedule napi poll by returning budget
- process Tx completions and update budget if necessary
- process Tx fetch indications (pull-push)
- push any other pending Tx (if possible)
- before resched or napi completion replenish htt rx ring buffer
- if work done < budget, complete napi poll and unmask interrupts
This change also get rid of two tasklets (intr_tq and txrx_compl_task).
Measured peak throughput with NAPI on IPQ4019 platform in controlled
environment. No noticeable reduction in throughput is seen and also
observed improvements in CPU usage. Approx. 15% CPU usage got reduced
in UDP uplink case.
DL: AP DUT Tx
UL: AP DUT Rx
IPQ4019 (avg. cpu usage %)
========
TOT +NAPI
=========== =============
TCP DL 644 Mbps (42%) 645 Mbps (36%)
TCP UL 673 Mbps (30%) 675 Mbps (26%)
UDP DL 682 Mbps (49%) 680 Mbps (49%)
UDP UL 720 Mbps (28%) 717 Mbps (11%)
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trivial fix to spelling mistake in ath10k_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Older firmware with HTT delivers incorrect tx status for null func
frames to driver, but this fixed in 10.2 and 10.4 firmware versions.
Also this workaround results in reporting of incorrect null func status
for 10.4. Fix this is by introducing a firmware feature flag for 10.4
so that this workaround is skipped and proper tx status for null func
frames are reported
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 97f2645f35 ("tree-wide: replace config_enabled() with
IS_ENABLED()") mostly did away with config_enabled().
This is one of the postponed TODO items as config_enabled() is used
for a tristate option here. Theoretically, config_enabled() is
equivalent to IS_BUILTIN(), but I guess IS_REACHABLE() is the best
fit for this case because both CONFIG_HWMON and CONFIG_ATH10K are
tristate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For 10.4 fw versions, dbglog module id has been extended from u32
to u64, hence this patch fixes the same in the ath10k driver side.
This patch doesn't break the older 10.4 releases. The FW change
is already present in the older FWs.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
waiter context waker context
scan.started
------------
ath10k_start_scan()
lockdep_assert_held(conf_mutex)
auth10k_wmi_start_scan()
wait_for_completion_timeout(scan.started)
ath10k_wmi_event_scan_start_failed()
complete(scan.started)
ath10k_wmi_event_scan_started()
complete(scan.started)
scan.completed
--------------
ath10k_scan_stop()
lockdep_assert_held(conf_mutex)
ath10k_wmi_stop_scan()
wait_for_completion_timeout(scan.completed)
__ath10k_scan_finish()
complete(scan.completed)
scan.on_channel
---------------
ath10k_remain_on_channel()
mutex_lock(conf_mutex)
ath10k_start_scan()
wait_for_completion_timeout(scan.on_channel)
ath10k_wmi_event_scan_foreign_chan()
complete(scan.on_channel)
offchan_tx_completed
--------------------
ath10k_offchan_tx_work()
mutex_lock(conf_mutex)
reinit_completion(offchan_tx_completed)
wait_for_completion_timeout(offchan_tx_completed)
ath10k_report_offchain_tx()
complete(offchan_tx_completed)
install_key_done
----------------
ath10k_install_key()
lockep_assert_held(conf_mutex)
reinit_completion(install_key_done)
wait_for_completion_timeout(install_key_done)
ath10k_htt_t2h_msg_handler()
complete(install_key_done)
vdev_setup_done
---------------
ath10k_monitor_vdev_start()
lockdep_assert_held(conf_mutex)
reinit_completion(vdev_setup_done)
ath10k_vdev_setup_sync()
wait_for_completion_timeout(vdev_setup_done)
ath10k_wmi_event_vdev_start_resp()
complete(vdev_setup_done)
ath10k_monitor_vdev_stop()
lockdep_assert_held(conf_mutex)
reinit_completion(vdev_setup_done()
ath10k_vdev_setup_sync()
wait_for_completion_timeout(vdev_setup_done)
ath10k_wmi_event_vdev_stopped()
complete(vdev_setup_done)
thermal.wmi_sync
----------------
ath10k_thermal_show_temp()
mutex_lock(conf_mutex)
reinit_completion(thermal.wmi_sync)
wait_for_completion_timeout(thermal.wmi_sync)
ath10k_thermal_event_temperature()
complete(thermal.wmi_sync)
bss_survey_done
---------------
ath10k_mac_update_bss_chan_survey
lockdep_assert_held(conf_mutex)
reinit_completion(bss_survey_done)
wait_for_completion_timeout(bss_survey_done)
ath10k_wmi_event_pdev_bss_chan_info()
complete(bss_survey_done)
All complete() calls happen while the conf_mutex is taken. That means
at max one waiter is possible.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the wake tx queue path, we are not checking if the frame to be sent
takes management path or not. For eg. QOS null func frame coming here will
take the management path. Since we are not incrementing the descriptor
counter (num_pending_mgmt_tx) w.r.t tx management, on tx completion it is
possible to see negative values.
When the above counter reaches a negative value, we will not be sending a
probe response out.
if (is_presp &&
ar->hw_params.max_probe_resp_desc_thres < htt->num_pending_mgmt_tx)
For IPQ4019, max_probe_resp_desc_thres (u32) is 24 is compared against
num_pending_mgmt_tx (int) and the above condtions comes true if the counter
is negative and we drop the probe response.
To avoid this, check on the wake tx queue path as well for the tx path of
the frame and increment the appropriate counters
Fixes: cac085524c "ath10k: move mgmt descriptor limit handle under mgmt_tx"
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
txqs_lock is interfering with wake_tx_queue submitting more frames.
so queues don't get filled in and don't keep firmware/hardware busy
enough. This change helps to reduce the txqs_lock contention and
wake_tx_queue() blockage to being possible in txrx_unref().
To reduce turn around time of wake_tx_queue ops and to maintain fairness
among all txqs, the callback is updated to push first txq alone from
pending list for every wake_tx_queue call. Remaining txqs will be
processed later upon tx completion.
Below improvements are observed in push-only mode and validated on
IPQ4019 platform. With this change, in AP mode ~10Mbps increase is
observed in downlink (AP -> STA) traffic and approx. 5-10% of CPU
usage is reduced.
Major improvement is observed in 1-hop Mesh mode topology in 11ACVHT80.
Compared to Infra mode, CPU overhead is higher in Mesh mode due to path
lookup and no fast-xmit support. So reducing spin lock contention is
helping in Mesh.
TOT +change
-------- --------
TCP DL 545 Mbps 595 Mbps
TCP UL 555 Mbps 585 Mbps
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'WMI_10_4_WDS_PEER_EVENTID' is not yet handled/implemented for WDS mode,
as of now suppress the warning message "Unknown eventid: 36903"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent commit 46f6b06050 ("mac80211: Encrypt "Group addressed privacy" action
frames") encrypts group privacy action frames. But qca99x0 family chipset
delivers broadcast/multicast management frames as encrypted and it should be
decrypted by mac80211. Setting RX_FLAG_DECRYPTED stats for those frames is
breaking mesh connection establishment.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With the %pK format specifier we hide the kernel addresses
with the help of kptr_restrict sysctl.
In this patch, %p is changed to %pK in the driver code.
The sysctl is documented in Documentation/sysctl/kernel.txt.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT service has missed in
the commit 7e247a9e88 ("ath10k: add dynamic tx mode switch
config support for qca4019"). This patch adds the service to
avoid mismatch between host and target.
Fixes: 7e247a9e88 ("ath10k: add dynamic tx mode switch config support for qca4019")
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW Rx filters and masks are not configured
properly by firmware during boot sequences. The
MAC_PCU_ADDR1 is set to 0s instead of 1s which
allows the HW to ACK any frame that passes through
MAC_PCU_RX_FILTER. The MAC_PCU_RX_FILTER itself
is misconfigured on boot as well.
The combination of these bugs ended up with the
following manifestations:
- "no channel configured; ignoring frame(s)!"
warnings in the driver
- spurious ACKs (transmission) on the air during
firmware bootup sequences
The former was a long standing and known bug
originally though mostly harmless.
However Marek recently discovered that this
problem also involves ACKing *all* frames the HW
receives (including beacons ;). Such frames
are delivered to host and generate the former
warning as well.
This could be a problem with regulatory compliance
in some rare cases (e.g. Taiwan which forbids
transmissions on channel 36 which is the default
bootup channel on 5Ghz band cards). The good news
is that it'd require someone else to violate
regulatory first to coerce our device to generate
and transmit an ACK.
The problem could be reproduced in a rather busy
environment that has a lot of APs. The likelihood
could be increased by injecting an msleep() of
5000 or longer immediately after
ath10k_htt_setup() in ath10k_core_start().
The reason why the former warnings were only
showing up seldom is because the device was either
quickly reset again (i.e. during firmware probing)
or wmi vdev was created (which fixes hw and fw
states).
It is technically possible for host driver to
override adequate hw registers however this can't
work reliably because the bug root cause lies in
incorrect firmware state on boot (internal
structure used to program MAC_PCU_ADDR1 is not
properly initialized) and only vdev create/delete
events can fix it. This is why the patch takes
dummy vdev approach.
This could be fixed in firmware as well but having
this fixed in driver is more robust, most notably
when thinking of users of older firmware such as
999.999.0.636.
Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows placing command barriers for explicit
serializing and synchronizing state.
Useful for future driver development.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds testmode support for 10.4 based chipsets
and added code swap support for UTF binary.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently testmode events for 10.x firmware are processed from
10.1 wmi event processing. This patch is used to handle testmode
events in 10.2 and 10.4 based firmware.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Preparation to make use of firmware_swap_code_seg_info for UTF binary.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Support for QCA9887 is no longer experimental and if there are any issues
we need to address them
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.
However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As hw cycle counters in QCA4019 wraparound independantly in QCA4019
it is possible cycle counter and rx clear counter would wraparound
at the same time. Current logic assumes only one of the counters
would wraparound at anytime. Fix this by moving 'else' part to
another 'if'.
Fixes: 8e100354a9 ("ath10k: fix cycle counter wraparound handling for QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Print an ath10k error message rather a call trace when HTT op version is
not found from firmware META data (IE). This should be sufficient to figure
out what went wrong.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9888 shares the same configuration with QCA99X0
with NSS=2.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rtc_state_cold_reset_mask is unused in ath10k_hw_regs.
instead fixed delays are used.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If WMI and/or firmware has issues removing the peer object,
then we still need to clean up the peer object in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not sure this can happen, but seems like a reasonable sanity
check.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
just to comply to coding style.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is expected that all pktlog events for 10.4 firmware based solutions
should come through CE8 where as in case of 10.2 firmware based solutions,
it should come through one of the HTT events (HTT_T2H_MSG_TYPE_PKTLOG).
But from experiments with 10.4 based solutions, it is observed that pktlog
event for ATH_PKTLOG_TYPE_TX_MSDU_ID is coming through HTT pktlog event.
Currently, we always parse with 10.2 pktlog header which will lead to
pktlog decoding issues (payload length mismatch exceptions)
For trace points, it is required to provide only the payload size. So
fixing this by simplifying the payload size calculation without the use of
ath10k pktlog headers.
While there, remove the unused ath10k pktlog headers.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
<linux/semaphore.h> is not used anymore, so just remove the include.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While debugging OS crashes due to firmware crashes, I enabled
kasan, and it noticed that peer objects were being used-after-freed.
Looks like there are two places we could be leaving stale references
in the peer-map, so clean that up.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise, the txrx-compl-task may access some bad memory?
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211/nl80211 interface changes for per STA total rx-duration and
very basic 'ath10k_sta_statistics' mac80211 callback is implemented
to extend support for per station statistics from the driver.
Also provision in 'iw dev wlan#N station dump' to parse rx-duration
is supported. So its safer to remove the debugfs entry for per STA
rx-duration
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable support for 'drv_sta_statistics' callback.
Export rx_duration support if available to cfg80211/nl80211
This can also act as a placeholder for any new per STA stats support
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled
The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats
{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}
Fixes: f9575793d4 ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Found this obvious typo while going through the spectral
code design in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Disable TX_STBC for both HT and VHT if the devices tx chainmask is '1'
TX_STBC is required only for devices with tx_chainmask > 1. This fixes
a ping failure for QCA9887 (1x1) in HT/VHT mode
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable beacon loss detection support for 10.4 by handling
roam event. With this change QCA99X0 station is able to
detect beacon loss when the AP is powered off
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch warns about a number of cases in ath10k where a pointer is
null-checked after it has already been dereferenced, in code involving
ath10k private virtual interface pointers.
Fix these by making the dereference happen later.
Addresses the following smatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:3651 ath10k_mac_txq_init() warn: variable dereferenced before check 'txq' (see line 3649)
drivers/net/wireless/ath/ath10k/mac.c:3664 ath10k_mac_txq_unref() warn: variable dereferenced before check 'txq' (see line 3659)
drivers/net/wireless/ath/ath10k/htt_tx.c:70 __ath10k_htt_tx_txq_recalc() warn: variable dereferenced before check 'txq->sta' (see line 52)
drivers/net/wireless/ath/ath10k/htt_tx.c:740 ath10k_htt_tx_get_vdev_id() warn: variable dereferenced before check 'cb->vif' (see line 736)
drivers/net/wireless/ath/ath10k/txrx.c:86 ath10k_txrx_tx_unref() warn: variable dereferenced before check 'txq' (see line 84)
drivers/net/wireless/ath/ath10k/wmi.c:1837 ath10k_wmi_op_gen_mgmt_tx() warn: variable dereferenced before check 'cb->vif' (see line 1825)
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The below warning message seems to hit occasionally with the following
combination (IPQ4019 + ACS scan) where we receive packets as a self peer
when hostapd does ACS when we bring up AP mode . ath10k has the below
fall back mechanism to fetch current operating channel in rx (it will
check for the next channel tracking variable if the current one is NULL)
[scan channel] --> [rx channel] --> [peer channel] -->
[vdev channel] --> [any vdev channel] --> [target oper channel]
'scan channel' and 'target operating channel' are directly fetched from
firmware events. All the others should be updated by mac80211.
During ACS scan we wouldn't have a valid channel context
assigned from mac80211 ('ar->rx_channel'), and also relying on
('ar->scan_channel') is not helpful (it becomes NULL when it goes to
BSS channel and also when the scan event is completed). In short we
cannot always rely on these two channel tracking variables.
'Target Operating Channel' (ar->tgt_oper_chan) seems to keep track of
the current operating even while we are doing ACS scan and etc. Hence
remove this un-necessary warning message and continue with
target_operating channel. At the worst case scenario when the target
operating channel is invalid (NULL) we already have an ath10k warning
message to notify we really don't have a proper channel configured in
rx to update the rx status("no channel configured; ignoring frame(s)!")
WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
[<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
(ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
[<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
[<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
[<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])
Fixes:3b0499e9ce42 ("ath10k: reduce warning messages during rx without proper channel context")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Usually when the firmware crashes we check for the value
'FW_IND_EVENT_PENDING' in 'FW_INDICATOR_ADDRESS' and proceed with
disabling the irq and dumping firmware 'crash dump'. Now
when the PCI card is unplugged from the device the PCI controller
seems to generate a spurious interrupt after some time which
was as treated a firmware crash and resulting in the below race
condition (and eventually crashing the system)
ath10k_core_unregister -> ath10k_core_free_board_files
...... device unplug spurious interrupt .........
ath10k_pci_taklet -> ath10k_pci_fw_crashed_dump ...etc
Clearly even after the firmware board files related data structure
is freed up we are getting a spurious interrupt from PCI with 0xfffffff
in the 'FW_INDICATOR_ADDRESS' resulting in scheduling of the pci tasklet
and doing a crash dump, printing f/w board related info resulting in the
below crash. Fix this by detecting this spurious interrupt in ath10k PCI
irq handler itself and return IRQ_NONE. Thanks to Michal Kazior for
helping us conclude the most appropriate fix.
Call trace:
EIP is at ath10k_debug_print_board_info+0x39/0xb0
[ath10k_core]
EAX: 00000000 EBX: d4de15a0 ECX: 00000000 EDX: 00000064
ESI: f615ddd0 EDI: f8530000 EBP: f615de3c ESP: f615ddbc
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 01c0a000 CR4: 000006f0
Stack:
f615ddd0 00000064 f8b4ecdd 00000000 00000000 00412f4e
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
Call Trace:
[<f8b1f517>] ath10k_print_driver_info+0x17/0x30
[ath10k_core]
[<f875463a>] ath10k_pci_fw_crashed_dump+0x7a/0xe0
[ath10k_pci]
[<f87549d0>] ath10k_pci_tasklet+0x70/0x90 [ath10k_pci]
[<c106151e>] tasklet_action+0x9e/0xb0
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5c86d97bcc ("ath10k: combine txrx and replenish task")
introduced deadlock while processing rx in order indication message
for qca6174 based devices. While merging replenish and txrx tasklets,
replenish task should be called out of htt rx ring locking since it
is also try to acquire the same lock.
Unfortunately this issue is not exposed by other solutions (qca988x,
qca99x0 & qca4019), as rx_in_ord_ind message is specific to qca6174
based devices. This patch fixes
=============================================
[ INFO: possible recursive locking detected ]
4.7.0-rc2-wt-ath+ #1353 Tainted: G E
---------------------------------------------
swapper/3/0 is trying to acquire lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d7ef19>]
ath10k_htt_rx_msdu_buff_replenish+0x29/0x90 [ath10k_core]
but task is already holding lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&htt->rx_ring.lock)->rlock);
lock(&(&htt->rx_ring.lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by swapper/3/0:
#0: (&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=119151
Fixes: 5c86d97bcc ("ath10k: combine txrx and replenish task")
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA4019, cycle counter wraparound is not tied to rx
clear counter. Each counter would wraparound individually
and after wraparound the respective counter will be reset
to 0x7fffffff while other counter still running unaffected.
Define a new wraparound type for this behaviour and handle
it separately so that rx clear counter wraparound is also
handled just like cycle counter. With this type of
wraparound we can accurately compute and report channel
active/busy time when any of the counter overflows.
Fixes: ee9ca147c5 ("ath10k: Fix survey reporting with QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X hw implements a different cycle counter wraparound
behaviour when compared to QCA4019. To properly handle different
wraparound logic for these chipsets replace already available
bool hw_params member, has_shifted_cc_wraparound, with an
enum which could be extended to handle different wraparound
behaviour. This patch keeps the existing logic functionally
same and a prepares cycle counter wraparound handling to
extend for other chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: change also QCA9887 wrap type]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CCK hardware table mapping from QCA99X0 onwards got revised.
The CCK hardware rate values are in a proper order wrt. to
rate and preamble as below
ATH10K_HW_RATE_REV2_CCK_LP_1M = 1,
ATH10K_HW_RATE_REV2_CCK_LP_2M = 2,
ATH10K_HW_RATE_REV2_CCK_LP_5_5M = 3,
ATH10K_HW_RATE_REV2_CCK_LP_11M = 4,
ATH10K_HW_RATE_REV2_CCK_SP_2M = 5,
ATH10K_HW_RATE_REV2_CCK_SP_5_5M = 6,
ATH10K_HW_RATE_REV2_CCK_SP_11M = 7,
This results in reporting of rx frames (with CCK rates)
totally wrong for QCA99X0, QCA4019. Fix this by having
separate CCK rate table for these chipsets with rev2 suffix
and registering the correct rate mapping to mac80211 based on
the new hw_param (introduced) 'cck_rate_map_rev2' which shall
be true for any newchipsets from QCA99X0 onwards
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All these flags are not used and their use is completely
covered by 'ath10k_hw_rate_ofdm', 'ath10k_hw_rate_cck',
and RX_PPDU_START_RATE_FLAG
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only five bits are defined to pass tid information in HTT_RX_IND
message, so the mask which can be used to extract tid should be 0x1f
instead of the current 0x3f. Also, macros which can be used to extract
flush_valid and release_valid bits have to be left shifted one bit less
because these information follow the tid right after. This patch does
not really fix anything functionally because these macros are not used
currently.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This looks like a regression from commit c4cdf753ed ("ath10k: move
fw_features to struct ath10k_fw_file"), we were printing the features from a
wrong struct.
Fixes: c4cdf753ed ("ath10k: move fw_features to struct ath10k_fw_file")
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA9887 stores its calibration data (board.bin) inside the EEPROM of
the target. This has to be downloaded manually to allow the device to
initialize correctly.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[kvalo@qca.qualcomm.com: handle -EOPNOTSUPP and s/fetch_board_data/fetch_cal_eeprom]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the hardware name, revision, firmware names and update the pci_id
table.
QA9887 HW1.0 is supposed to be similar to QCA988X HW2.0 . Details about
he firmware interface are currently unknown.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[kvalo@qca.qualcomm.com: add a warning about experimental support]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All the necessary patches to make wifi running (over AHB)
on ipq4019 SoC are ready now. It's good to enable
ipq4019 wifi device probing in ahb module and
remove work in progress debug print.
Device tree change is there in the public review by
below commit message
"qcom: ipq4019: add wifi nodes to ipq4019 SoC device tree"
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware has support to enable or disable btcoex functionality
without reloading firmware via wmi pdev param. Add provision to send
pdev param command via existing btcoex knob.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This feature flag will be used for firmware to support BT-Coex feature
without reloading firmware via WMI pdev param. To support Bluetooth
coexistence pdev param, WMI_COEX_GPIO_SUPPORT of extended resource
config should be enabled always. This firmware IE is used to configure
WMI_COEX_GPIO_SUPPORT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update module description to advertise all supported QCA 802.11ac devices.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove unused inline function phy_mode_to_band.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Earlier when operating irq mode is legacy, interrupts are disabled
and re-enabled based on num_msi_intrs. commit cfe9011a05 ("ath10k:
remove MSI range support") replaced num_msi_intrs by oper_irq_mode.
Since oper_irq_mode is not initialized for ahb devices (i.e qca4019),
device boot up is failed during probe.
Fixes: cfe9011a05 ("ath10k: remove MSI range support")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix invalid argument error while writing 'simulate_fw_crash',
though the funcionality is working fine we get an error 'invalid
argument' because 'count' value is not returned properly
(no reason to reduce the count value for removing the newline)
Fixes the below write error:
/sys/kernel/debug/ieee80211/phy0/ath10k# echo hw-restart >
simulate_fw_crash
-bash: echo: write error: Invalid argument
Also move the 'conf_mutex' as it is really not required for
fetching the userspace buffer.
Reported-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diag_read uses dma_alloc_coherent to allocate memory requested by the
caller. If this memory requested is larger, more than DIAG_TRANSFER_LIMIT
(2K), then it is likely that we may not get the requested memory and we
would fail.
To solve this, request dma_alloc_coherent for only DIAG_TRANSFER_LIMIT, and
reuse this buffer multiple times as needed to copy the data requested in
smaller chunks of size not more than DIAG_TRANSFER_LIMIT. Previously we
were reading into the caller's only after getting the complete requested
data.
Fixes: 68c03249f3 ('ath10k: convert pci_alloc_consistent() to dma_alloc_coherent()')
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Legacy rate packets may not necessarily be having a rx status
flag of '0' always, for example management frame have flags
like RX_FLAG_ONLY_MONITOR / RX_FLAG_MACTIME_END also set
Just check 'VHT' and 'HT' flags are not set , and simply clasify it as
legacy rate packets
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WARN_ON_ONCE when we receive packets for self peer when mac80211
had not assigned a proper channel context. This scenario happens
in QCA4019 when we start the AP via hostapd in background and start
it once again in the background without killing the previous instance!
This happens intermittently when we start / stop hostapd in a while loop
(incase the hostapd is not properly killed). This results in mac80211
chancontext to be unassigned, while the self peer continuous receive
packets in target operating channel. This results in lot of call traces
in the rx path. Make this as a WARN_ON_ONCE to avoid flooding the console
which result in rebooting low memory systems, while still reporting the
warning once that we are receiving packets in target operating channel and
to indicate that something is happening which is not the expected result.
WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
[<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
(ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
[<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
[<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
[<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent changes revolving around implementing
wake_tx_queue support introduced a significant
performance regressions on some (slower, uni-proc)
systems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 shares the same configuration with QCA99X0.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 Rx descriptor has two 32-bit words of location information
when compared to one 32-bit word in QCA99X0. To handle this difference in
rx descriptor ppdu_end, define a new ppdu_end for QCA9984 descriptor
which has the new structure to represent rx_location_info.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store pci chip secific reset funtions in struct ath10k_pci
as callbacks during early ath10k_pci_probe() and use the
callback to perform chip specific resets. This patch essentially
adds two callback in ath10k_pci, one for doing soft reset and
the other for hard reset. By using callbacks we can get rid of
those hw revision checks in ath10k_pci_safe_chip_reset() and
ath10k_pci_chip_reset(). As such this patch does not fix
any issue.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define rx_location_info in struct rx_ppdu_end_qca99x0 after
rx_pkt_end. This is to prepare rx_ppdu_end for QCA9984 chip.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA4019, cycle counter wraparound in same fashion
as QCA988X. When the cycle counter wraparound it
resets to 0x7fffffff. Set has_shifted_cc_wraparound to
true for QCA4019 to enable the code path to handle cycle
counter wraparound for consistent survey report.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In 10.4, fw sends WMI PEER_RATECODE_LIST_EVENTID after successful
peer_assoc cmd. As of now this event is not of much use and not
implemented. Change the debug level and messsage as appropriate
to suppress "Unknown eventid: 36898".
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During hw scan, firmware sends two channel information events (pre-
complete, complete) to host for each channel change. The snap shot of cycle
counters (rx_clear and total) between these two events are given for
survey dump. In order to get latest survey statistics of all channels, a
scan request has to be issued. In general, an AP DUT is brought up, it
won't leave BSS channel except few cases like overlapping bss or radar
detection. So survey statistics of bss channel is always referring to
older data that are collected before starting AP (either ACS/OBSS scan).
To collect latest survey information from target, firmware provides WMI
interface to read cycle counters from hardware. For each survey dump
request, BSS channel cycle counters are read and cleared in hardware.
This makes sure that behavior is in align with ath9k survey report.
So survey dump always gives snap shot of cycle counters b/w two survey
requests.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add handler to process bss channel information wmi event that
will be received upon sending pdev_chan_info_request wmi command.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI ops to send pdev_bss_chan_info_request command to target.
This command will be used to retrieve updated cycle counters and noise
floor value of current operating channel (bss channel).
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI definitions for pdev bss channel information request and
event.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is observed that while loading and unloading ath10k modules
in an infinite loop, before ath10k_core_start() completion HTT
rx frames are received, while processing these frames,
dereferencing the arvifs list code is getting hit before
initilizing the arvifs list, causing a kernel panic.
This patch initilizes the arvifs list before initilizing htt.
Fixes the below issue:
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core])
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core])
[<c0234100>] (tasklet_action+0x8c/0xec)
[<c0234100>] (tasklet_action)
[<c02337c0>] (__do_softirq+0xf8/0x228)
[<c02337c0>] (__do_softirq) [<c0233920>] (run_ksoftirqd+0x30/0x90)
Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008)
---[ end trace 71de5c2e011dbf56 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Spectral related structures are accessed / modified only if ath10k
debugfs is enabled, so it makes more sense to move them under
ATH10K_DEBUGFS
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to the spec, VHT doesn't exist in 2.4GHz.
There are vendor extensions to allow a subset of VHT to work
(notably 256-QAM), but since mac80211 doesn't support those
advertising VHT capability on 2.4GHz leads to the behaviour
of reporting VHT capabilities but not being able to use any
of them due to mac80211's code requiring 80 MHz support.
Remove the VHT capabilities from 2.4GHz for now. If mac80211
gets extended to use the (likely Broadcom) vendor IEs for it
and handles the lack of 80 MHz support, it can be added back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
fix a typo (spelling mistake) in 'ath10k_start'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA6174 WLAN.RM.2.0 firmware uses max_tx_power instead of using max_reg_power
to set transmission power. The tx power was about -50dbm, after applying this
change, it become -32dbm.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.7. Major changes:
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
Now that all firmware-N.bin related are within struct ath10k_fw_file we can
switch to use ath10k_core_fetch_firmware_api_n() and delete almost identical
ath10k_tm_fetch_utf_firmware_api_2().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to share ath10k_core_fetch_board_data_api_n() with testmode.c
refactor all firmware components to struct ath10k_fw_components. This structure
will hold firmware related files, for example firmware-N.bin and board-N.bin.
For firmware-N.bin create a new struct ath10k_fw_file which contains the actual
firmware image as well as the parsed data from the image.
Modify ath10k_core_start() to take struct ath10k_fw_components() as an argument
which makes it possible in following patches to drop some ugly hacks from
testmode.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This has ben deprecated years ago, I haven't heard anyone using it since and
most likely it won't even work anymore. So just remove all of it.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
push-pull mode needs certain amount the host driver involvement for
managing queues in the host memory and packet delivery to firmware.
qca4019 wifi firmware has an option to stay in push mode for less
number of active traffic flow and then switch to push-pull mode when
the active traffic flow goes beyond the certain limit.
The advantage of staying in push mode for less active traffic is, the
host cpu consumption is reduced. qca4019 firmware supports this
flexibility of the mode switch. It takes the host driver interest
(LOW_PERF/HIGH_PERF) via WMI_EXT_RESOURCE_CFG_CMDID,
LOW_PERF - fw would stay in push mode and switch to push-pull
based on demand.
HIGH_PERF - fw would stay in push-pull mode from the boot.
To make this configuration generic, new WMI services
WMI_SERVICE_TX_MODE_PUSH_ONLY, WMI_SERVICE_TX_MODE_PUSH_PULL,
WMI_SERVICE_TX_MODE_DYNAMIC are introduced to take dynamic tx mode
switch support availability in firmware.
Based on WMI_SERVICE_TX_MODE_DYNAMIC, LOW_PERF or HIGHT_PERF is
configured to the firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch complains that since "ev->peer_id" comes from skb->data that
means we can't trust it and have to do a bounds check on it to prevent
an array overflow.
Fixes: 6942726f7f ('ath10k: add fast peer_map lookup')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon firmware assert, restart work will be triggered so that mac80211
will reconfigure the driver. An issue is reported that after restart
work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info
for operating channel. During reconfigure, since mac80211 already has
valid channel context for given radio, channel context iteration return
num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning
channel context to rx_channel when driver restart is in progress.
Cc: stable@vger.kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return value is incorrect for btcoex and peer stats debugfs
'write' entries if the user provides a value that matches with
the already available debugfs entry, this results in the debugfs
entry getting stuck and the operation has to be terminated manually.
Fix this by returning the appropriate return 'count' as we do it for
other debugfs entries like pktlog etc.
Fixes: cc61a1bbbc ("ath10k: enable debugfs provision to enable Peer Stats feature")
Fixes: c28e6f06ff ("ath10k: fix sanity check on enabling btcoex via debugfs")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warning:
drivers/net/wireless/ath/ath10k/wmi.c:5800: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:452: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/mac.c:455: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/txrx.c:133: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1477: Prefer kernel type 'u64' over 'u_int64_t'
drivers/net/wireless/ath/ath10k/htt.h:1480: Prefer kernel type 'u64' over 'u_int64_t'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix checkpatch warnings about use of spaces with operators:
spaces preferred around that '*' (ctx:VxV)
This has been recently added to checkpatch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
MSI-X is never well-tested, might contain bugs and generally isn't
really all that useful to maintain. Also ath10k is mainly used with
shared/singly-MSI interrupt systems. Hence removing MSI range support.
This change will be useful for further cleanup in copy engine lock
and to add NAPI support.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware has addeded set_tsf vdev parameter,
hence enable it.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
