According to the LAN8710A datasheet (Rev. B, section 3.8.5.1), a hardware
reset is required after power-on, and the reference clock (REF_CLK) must be
established before asserting reset.
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Cc: Csókás Bence <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250728152916.46249-2-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Force a fixed MDI-X mode when auto-negotiation is disabled to prevent
link instability.
When forcing the link speed and duplex on a LAN9500 PHY (e.g., with
`ethtool -s eth0 autoneg off ...`) while leaving MDI-X control in auto
mode, the PHY fails to establish a stable link. This occurs because the
PHY's Auto-MDIX algorithm is not designed to operate when
auto-negotiation is disabled. In this state, the PHY continuously
toggles the TX/RX signal pairs, which prevents the link partner from
synchronizing.
This patch resolves the issue by detecting when auto-negotiation is
disabled. If the MDI-X control mode is set to 'auto', the driver now
forces a specific, stable mode (ETH_TP_MDI) to prevent the pair
toggling. This choice of a fixed MDI mode mirrors the behavior the
hardware would exhibit if the AUTOMDIX_EN strap were configured for a
fixed MDI connection.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Override the hardware strap configuration for MDI-X mode to ensure a
predictable initial state for the driver. The initial mode of the LAN87xx
PHY is determined by the AUTOMDIX_EN strap pin, but the driver has no
documented way to read its latched status.
This unpredictability means the driver cannot know if the PHY has
initialized with Auto-MDIX enabled or disabled, preventing it from
providing a reliable interface to the user.
This patch introduces a `config_init` hook that forces the PHY into a
known state by explicitly enabling Auto-MDIX.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct the Auto-MDIX configuration to ensure userspace settings are
respected when the feature is disabled by the AUTOMDIX_EN hardware strap.
The LAN9500 PHY allows its default MDI-X mode to be configured via a
hardware strap. If this strap sets the default to "MDI-X off", the
driver was previously unable to enable Auto-MDIX from userspace.
When handling the ETH_TP_MDI_AUTO case, the driver would set the
SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required
SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY
falls back to its hardware strap default, ignoring the software request.
This patch corrects the behavior by also setting the override bit when
enabling Auto-MDIX. This ensures that the userspace configuration takes
precedence over the hardware strap, allowing Auto-MDIX to be enabled
correctly in all scenarios.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250703114941.3243890-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'struct mdio_device_id' is not modified in these drivers.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
27014 12792 0 39806 9b7e drivers/net/phy/broadcom.o
After:
=====
text data bss dec hex filename
27206 12600 0 39806 9b7e drivers/net/phy/broadcom.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/403c381b7d9156b67ad68ffc44b8eee70c5e86a9.1736691226.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fold the separate call to clk_set_rate() into the clock getter.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241007134100.107921-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microchip LAN8740/LAN8742 PHYs support basic unicast, broadcast, and
Magic Packet WoL. They have one pattern filter matching up to 128 bytes
of frame data, which can be used to implement ARP or multicast WoL.
ARP WoL matches any ARP frame with broadcast address.
Multicast WoL matches any multicast frame.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/1690329270-2873-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable EDPD PHY tunable support for all drivers using
lan87xx_read_status.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the EDPD PHY tunable.
Per default EDPD is disabled in interrupt mode, the tunable can be used
to override this, e.g. if the link partner doesn't use EDPD.
The interval to check for energy can be chosen between 1000ms and
2000ms. Note that this value consists of the 1000ms phylib interval
for state machine runs plus the time to wait for energy being detected.
v2:
- consider that phylib core holds phydev->lock when calling the
phy tunable hooks
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a member edpd_max_wait_ms to the private data structure in preparation
of making the wait period configurable by supporting the edpd phy tunable.
v2:
- rename constant to EDPD_MAX_WAIT_DFLT_MS
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flag edpd_mode_set_by_user in preparation of adding edpd phy tunable
support. This flag will allow users to override the default behavior
of edpd being disabled if interrupt mode is used.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear edpd_enable if interupt mode is used, this avoids
having to check for PHY_POLL multiple times.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper smsc_phy_config_edpd() and explicitly clear bit
MII_LAN83C185_EDPWRDOWN is edpd_enable isn't set.
Boot loader may have left whatever value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the flag to edpd_enable, as we're not enabling energy but
edpd (energy detect power down) mode. In addition change the
type to a bit field member in preparation of adding further flags.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Amlogic Meson internal PHY's have the same register layout as
certain SMSC PHY's (also for non-c22-standard registers). This seems
to be more than just coincidence. Apparently they also need the same
workaround for EDPD mode (energy detect power down). Therefore let's
export SMSC PHY driver functionality for use by the meson-gxl PHY
driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Chris Healy <healych@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If genphy_read_status fails then further access to the PHY may result
in unpredictable behavior. To prevent this bail out immediately if
genphy_read_status fails.
Fixes: 4223dbffed ("net: phy: smsc: Re-enable EDPD mode for LAN87xx")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/026aa4f2-36f5-1c10-ab9f-cdb17dda6ac4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
lan95xx_config_aneg_ext() can be simplified by using phy_set_bits().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/3da785c7-3ef8-b5d3-89a0-340f550be3c2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently link up can't be detected in forced mode if polling
isn't used. Only link up interrupt source we have is aneg
complete which isn't applicable in forced mode. Therefore we
have to use energy-on as link up indicator.
Fixes: 7365494550 ("net: phy: smsc: skip ENERGYON interrupt if disabled")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon reports that if two LAN9514 USB adapters are directly connected
without an intermediate switch, the link fails to come up and link LEDs
remain dark. The issue was introduced by commit 1ce8b37241 ("usbnet:
smsc95xx: Forward PHY interrupts to PHY driver to avoid polling").
The PHY suffers from a known erratum wherein link detection becomes
unreliable if Energy Detect Power-Down is used. In poll mode, the
driver works around the erratum by briefly disabling EDPD for 640 msec
to detect a neighbor, then re-enabling it to save power.
In interrupt mode, no interrupt is signaled if EDPD is used by both link
partners, so it must not be enabled at all.
We'll recoup the power savings by enabling SUSPEND1 mode on affected
LAN95xx chips in a forthcoming commit.
Fixes: 1ce8b37241 ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling")
Reported-by: Simon Han <z.han@kunbus.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/439a3f3168c2f9d44b5fd9bb8d2b551711316be6.1655714438.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 4c0d2e96ba ("net: phy: consider that suspend2ram may cut
off PHY power"), phy_init_hw() invokes both, the ->config_init() and
->config_intr() callbacks.
In the SMSC PHY driver, the latter acknowledges stale interrupts, hence
there's no longer a need to acknowledge them in the former as well.
There are no other callers of ->config_init() besides phy_init_hw().
Drop the redundant code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/0254edf48bddc96c6248c4414043a3699e94614a.1655716767.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If reading the Interrupt Source Flag register fails with -ENODEV, then
the PHY has been hot-removed and the correct response is to bail out
instead of throwing a WARN splat and attempting to suspend the PHY.
The PHY should be stopped in due course anyway as the kernel
asynchronously tears down the device.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache the interrupt mask to avoid re-reading it from the PHY upon every
interrupt.
This will simplify a subsequent commit which detects hot-removal in the
interrupt handler and bails out.
Analyzing and debugging PHY transactions also becomes simpler if such
redundant reads are avoided.
Last not least, interrupt overhead and latency is slightly improved.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
add comments for the LAN8742 phy ID mask in the previous patch.
add one missing tab in the LAN8742 phy ID line.
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current phy IDs on the available hardware.
LAN8742 0x0007C130, 0x0007C131
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function lan87xx_config_aneg_ext was introduced to configure
LAN95xxA but as well writes to undocumented register of LAN87xx.
This fix prevents that access.
The function lan87xx_config_aneg_ext gets more suitable for the new
behavior name.
Reported-by: Måns Rullgård <mans@mansr.com>
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bedd8d78ab ("net: phy: smsc: LAN8710/20: add phy refclk in
support") added the phy clk support. The commit already checks if
clk_get_optional() throw an error but instead of returning the error it
ignores it.
Fixes: bedd8d78ab ("net: phy: smsc: LAN8710/20: add phy refclk in support")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210111085932.28680-1-m.felsch@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the missing clk_disable_unprepare() before return from
smsc_phy_probe() in the error handling case.
Fixes: bedd8d78ab ("net: phy: smsc: LAN8710/20: add phy refclk in support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605180239-1792-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't reset the phy without respect to the PHY library state machine
because this breaks the phy IRQ mode. The same behaviour can be archived
now by specifying the refclk.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to specify the clock provider for the PHY refclk and don't
rely on 'magic' host clock setup. [1] tried to address this by
introducing a flag and fixing the corresponding host. But this commit
breaks the IRQ support since the irq setup during .config_intr() is
thrown away because the reset comes from the side without respecting the
current PHY state within the PHY library state machine. Furthermore the
commit fixed the problem only for FEC based hosts other hosts acting
like the FEC are not covered.
This commit goes the other way around to address the bug fixed by [1].
Instead of resetting the device from the side every time the refclk gets
(re-)enabled it requests and enables the clock till the device gets
removed. Now the PHY library is the only place where the PHY gets reset
to respect the PHY library state machine.
[1] commit 7f64e5b18e ("net: phy: smsc: LAN8710/20: add
PHY_RST_AFTER_CLK_EN flag")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exit the driver specific config_init hook early if energy detection is
disabled. We can do this because we don't need to clear the interrupt
status here. Clearing the status should be removed anyway since this is
handled by the phy_enable_interrupts().
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't enable the interrupt if the platform disable the energy detection
by "smsc,disable-energy-detect".
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, each PHY has their own configuration and it can be done
through an external PHY driver. The smsc95xx driver uses only the
hard-coded internal PHY configuration.
This patch adds phylib support to probe external PHY drivers for
configuring external PHYs.
The MDI-X configuration for the internal PHYs moves from
drivers/net/usb/smsc95xx.c to drivers/net/phy/smsc.c.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7ae7ad2f11 ("net: phy: smsc: use phy_read_poll_timeout()
to simplify the code") will print a lot of logs as follows when Ethernet
cable is not connected:
[ 4.473105] SMSC LAN8710/LAN8720 2188000.ethernet-1:00: lan87xx_read_status failed: -110
When wait 640 ms for check ENERGYON bit, the timeout should not be
regarded as an actual error and an error message also should not be
printed. due to a hardware bug in LAN87XX device, it leads to unstable
detection of plugging in Ethernet cable when LAN87xx is in Energy Detect
Power-Down mode. the workaround for it involves, when the link is down,
and at each read_status() call:
- disable EDPD mode, forcing the PHY out of low-power mode
- waiting 640ms to see if we have any energy detected from the media
- re-enable entry to EDPD mode
This is presumably enough to allow the PHY to notice that a cable is
connected, and resume normal operations to negotiate with the partner.
The problem is that when no media is detected, the 640ms wait times
out and this commit was modified to prints an error message. it is an
inappropriate conversion by used phy_read_poll_timeout() to introduce
this bug. so fix this issue by use read_poll_timeout() to replace
phy_read_poll_timeout().
Fixes: 7ae7ad2f11 ("net: phy: smsc: use phy_read_poll_timeout() to simplify the code")
Reported-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify lan87xx_read_status() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN8740, like the 8720, also requires a reset after enabling clock.
The datasheet [1] 3.8.5.1 says:
"During a Hardware reset, an external clock must be supplied
to the XTAL1/CLKIN signal."
I have observed this issue on a custom i.MX6 based board with
the LAN8740A.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/8740a.pdf
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
U64_MAX is well defined now while the UINT64_MAX is not, so we fall
back to drivers' own definition as below:
#ifndef UINT64_MAX
#define UINT64_MAX (u64)(~((u64)0))
#endif
I believe this is in one phy driver then copied and pasted to other phy
drivers.
Replace the UINT64_MAX with U64_MAX to clean up the source code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
