Raju Lakkaraju reported that the below commit caused a regression
with Lan743x drivers and a 2.5G SFP. Sadly, this is because the commit
was utterly wrong. Let's fix this properly by not moving the
linkmode_and(), but instead copying the link ksettings and then
modifying the advertising mask before passing the modified link
ksettings to phylib.
Fixes: df0acdc59b ("net: phylink: fix ksettings_set() ethtool call")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q4eLm-00Ayxk-GZ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add two helper functions for calling PCS methods. phylink_pcs_config()
allows us to handle PCS configuration specifics in one location, rather
than the two call sites. phylink_pcs_link_up() gives us consistency.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q1TzK-007Exd-Rs@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a function to resolve clause 73 negotiation according to the
priority resolution function described in clause 73.3.6.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Phylink had two chunks of code virtually the same for resolving the
negotiated pause modes. Factor this down to one function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have been requiring the supported_interfaces bitmap to be filled in
by MAC drivers that have a mac_select_pcs() method. Now that all MAC
drivers fill in the supported_interfaces bitmap, it is time to enforce
this. We have already required supported_interfaces to be set in order
for optical SFPs to be configured in commit f81fa96d8a ("net: phylink:
use phy_interface_t bitmaps for optical modules").
Refuse phylink creation if supported_interfaces is empty, and remove
code to deal with cases where this mask is empty.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1q0K1u-006EIP-ET@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are several places which open code comparing PHY IDs. Provide a
couple of helpers to assist with this, using a slightly simpler test
than the original:
- phy_id_compare() compares two arbitary PHY IDs and a mask of the
significant bits in the ID.
- phydev_id_compare() compares the bound phydev with the specified
PHY ID, using the bound driver's mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to the SFP layer to allow phylink to set the signalling
rate for a SFP module. The rate given will be in units of kilo-baud
(1000 baud).
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
6ead9c98ca ("net: fec: remove the xdp_return_frame when lack of tx BDs")
144470c88c ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While testing a Fiberstore SFP-10G-T module (which uses 10GBASE-R with
rate adaption) in a Clearfog platform (which can't do that) it was
found that the PHYs advertisement was not limited according to the
hosts capabilities when using ethtool to change it.
Fix this by ensuring that we mask the advertisement with the computed
support mask as the very first thing we do.
Fixes: cbc1bb1e46 ("net: phylink: simplify phy case for ksettings_set method")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both phylink_create() and phylink_fwnode_phy_connect() do not modify
the fwnode argument that they are passed, so lets constify these.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide phylink_expects_phy() to allow MAC drivers to check if it
is expecting a PHY to attach to. Since fixed-linked setups do not
need to attach to a PHY.
Provides a boolean value as to if the MAC should expect a PHY.
Returns true if a PHY is expected.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Autoneg bit in the advertising bitmap and state->an_enabled are
always identical. state->an_enabled is now no longer used by any
drivers, so lets kill this duplication.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In fixed-link setup phylink_parse_fixedlink() unconditionally sets
Pause, Asym_Pause and Autoneg bits to "supported" bitmap, while MAC may
not support these.
This leads to ethtool reporting:
> Supported pause frame use: Symmetric Receive-only
> Supports auto-negotiation: Yes
regardless of what is actually supported.
Instead of unconditionally set Pause, Asym_Pause and Autoneg it is
sensible to set them according to validated "supported" bitmap, i.e. the
result of phylink_validate().
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
After calling fwnode_phy_find_device(), the phy device refcount is
incremented. Then, when the phy device is attached to a netdev with
phy_attach_direct(), the refcount is also incremented but only
decremented in the caller if phy_attach_direct() fails. Move
phy_device_free() before the "if" to always release it correctly.
Indeed, either phy_attach_direct() failed and we don't want to keep a
reference to the phydev or it succeeded and a reference has been taken
internally.
Fixes: 25396f680d ("net: phylink: introduce phylink_fwnode_phy_connect()")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S
Ethernet PHY. According to the specifications, the 10BASE-T1S supports
Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or
Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tim Harvey reports that link modes which he does not expect to be
supported are being advertised, and this is because of the workaround
we have for PHYs that switch interface modes.
Fix this up by checking whether rate matching will be used for the
requested interface mode, and if rate matching will be used, perform
validation only with the requested interface mode, rather than invoking
this workaround.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.
Any remaining instances that have not been addressed by this patch can
be fixed up later.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
state is deferenced earlier in the function, the NULL check
is pointless. Since we don't have any crash reports presumably
it's safe to assume state is not NULL.
Fixes: f392a18464 ("net: phylink: provide phylink_validate_mask_caps() helper")
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20221025185126.1720553-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide a helper that restricts the link modes according to the
phylink capabilities.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[rebased on net-next/master and added documentation]
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit
'commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state")'
requires the MAC driver explicitly tell the phy driver who is
managing the PM, otherwise you will see warning during resume
stage.
Add a boolean property in the phylink_config structure so that
the MAC driver can use it to tell the PHY driver if it wants to
manage the PM.
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFPs may contain an internal PHY which may in some cases want to
connect with the host interface in 1000base-x/2500base-x mode.
Do not fail if such PHY is being attached in one of these PHY interface
modes.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the supported PHY interface types to phylib if the PHY we are
connecting is inside a SFP, so that the PHY driver can select an
appropriate host configuration mode for their interface according to
the host capabilities.
For example the Marvell 88X3310 PHY inside RollBall SFP modules
defaults to 10gbase-r mode on host's side, and the marvell10g
driver currently does not change this setting. But a host may not
support 10gbase-r. For example Turris Omnia only supports sgmii,
1000base-x and 2500base-x modes. The PHY can be configured to use
those modes, but in order for the PHY driver to do that, it needs
to know which modes are supported.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_sfp_config() now only deals with configuring the MAC for a
SFP containing a PHY. Rename it to be specific.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where a MAC provides a phy_interface_t bitmap, use these bitmaps to
select the operating interface mode for optical SFP modules, rather
than using the linkmode bitmaps.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently parse the SFP EEPROM to a bitmap of ethtool link modes,
and then attempt to convert the link modes to a PHY interface mode.
While this works at present, there are cases where this is sub-optimal.
For example, where a module can operate with several different PHY
interface modes.
To start addressing this, arrange for the SFP EEPROM parsing to also
provide a bitmap of the possible PHY interface modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than having the ability to validate all supported interface
modes or a single interface mode, introduce the ability to validate
a subset of supported modes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[ rebased on current net-next ]
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for adjusting the advertisement for pause-based rate
matching. This may result in a lossy link, since the final link settings
are not adjusted. Asymmetric pause support is necessary. It would be
possible for a MAC supporting only symmetric pause to use pause-based rate
adaptation, but only if pause reception was enabled as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the phy is configured to use pause-based rate matching, ensure that
the link is full duplex with pause frame reception enabled. As
suggested, if pause-based rate matching is enabled by the phy, then
pause reception is unconditionally enabled.
The interface duplex is determined based on the rate matching type.
When rate matching is enabled, so is the speed. We assume the maximum
interface speed is used. This is only relevant for MLO_AN_PHY. For
MLO_AN_INBAND, the MAC/PCS's view of the interface speed will be used.
Although there are no RATE_ADAPT_CRS phys in-tree, it has been added for
comparison (and the implementation is quite simple).
Co-developed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we call phylink_caps_to_linkmodes directly from
phylink_get_linkmodes, it is difficult to re-use this functionality in
MAC drivers. This is because MAC drivers must then work with an ethtool
linkmode bitmap, instead of with mac capabilities. Instead, let the
caller of phylink_get_linkmodes do the conversion. To reflect this
change, rename the function to phylink_get_capabilities.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is convenient for MAC drivers. They can use it to add or
remove particular link modes based on capabilities (such as if half
duplex is not supported for a particular interface mode).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 1000BASE-KX interface mode. This 1G backplane ethernet as described in
clause 70. Clause 73 autonegotiation is mandatory, and only full duplex
operation is supported.
Although at the PMA level this interface mode is identical to
1000BASE-X, it uses a different form of in-band autonegation. This
justifies a separate interface mode, since the interface mode (along
with the MLO_AN_* autonegotiation mode) sets the type of autonegotiation
which will be used on a link. This results in more than just electrical
differences between the link modes.
With regard to 1000BASE-X, 1000BASE-KX holds a similar position to
SGMII: same signaling, but different autonegotiation. PCS drivers
(which typically handle in-band autonegotiation) may only support
1000BASE-X, and not 1000BASE-KX. Similarly, the phy mode is used to
configure serdes phys with phy_set_mode_ext. Due to the different
electrical standards (SFI or XFI vs Clause 70), they will likely want to
use different configuration. Adding a phy interface mode for
1000BASE-KX helps simplify configuration in these areas.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RGMII specification v2.0, section 3.4.1, RGMII/RTBI has an
optional in-band status feature where the PHY's link status, speed and
duplex mode can be passed to the MAC.
Allow RGMII/RTBI to use in-band status.
Signed-off-by: Qingfang DENG <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QUSGMII mode is a derivative of Cisco's USXGMII standard. This
standard is pretty similar to SGMII, but allows for faster speeds, and
has the build-in bits for Quad and Octa variants (like QSGMII).
The main difference with SGMII/QSGMII is that USXGMII/QUSGMII re-uses
the preamble to carry various information, named 'Extensions'.
As of today, the USXGMII standard only mentions the "PCH" extension,
which is used to convey timestamps, allowing in-band signaling of PTP
timestamps without having to modify the frame itself.
This commit adds support for that mode. When no extension is in use, it
behaves exactly like QSGMII, although it's not compatible with QSGMII.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are operating in SGMII inband mode, it implies that there is a
PHY connected, and the ethtool advertisement for autoneg applies to
the PHY, not the SGMII link. When in 1000base-X mode, then this applies
to the 802.3z link and needs to be applied to the PCS.
Fix this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1o9Ng2-005Qbe-3H@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current link mode of the phylink instance may not require an
attached PCS. However, phylink_major_config() unconditionally
dereferences this potentially NULL pointer when restarting the link poll
timer, which will panic the kernel.
Fix the problem by checking whether a PCS exists in phylink_pcs_poll_start(),
otherwise do nothing. The code prior to the blamed patch also only
looked at pcs->poll within an "if (pcs)" block.
Fixes: bfac8c490d ("net: phylink: disable PCS polling over major configuration")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Tested-by: Michael Walle <michael@walle.cc> # on kontron-kbox-a-230-ls
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com> # on sam9x60ek
Link: https://lore.kernel.org/r/20220629193358.4007923-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While we are performing a major configuration, there is no point having
the PCS polling timer running. Stop it before we begin preparing for
the configuration change, and restart it only once we've successfully
completed the change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the pcs_ops member from struct phylink, using the one stored in
struct phylink_pcs instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The QSGMII MAC-to-PHY reply is the same as the SGMII MAC-to-PHY reply.
Add support for this to phylink_mii_c22_pcs_encode_advertisement().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add entry for the 10base-T1L full duplex mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As there are now no users of phylink_helper_basex_speed(), we can
remove this obsolete functionality.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phylink to use %pe for printing error codes, which can print
them as errno symbols rather than numbers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1nOyEI-00Buu8-K9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As all users of phylink_set_pcs() have now been updated to use the
mac_select_pcs() method, it can be removed from the phylink kernel
API and its functionality moved into phylink_major_config().
Removing phylink_set_pcs() gives us a single approach for attaching
a PCS within phylink.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean reports that probing on DSA drivers that aren't yet
populating supported_interfaces now fails. Fix this by allowing
phylink to detect whether DSA actually provides an underlying
mac_select_pcs() implementation.
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Fixes: bde018222c ("net: dsa: add support for phylink mac_select_pcs()")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1nMCD6-00A0wC-FG@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phylink_config's pcs_poll is no longer used, let's get rid of it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_set_10g_modes() is no longer used with the conversion of
drivers to phylink_generic_validate(), so we can remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hook for PCS to validate the link parameters. This avoids MAC
drivers having to have knowledge of their PCS in their validate()
method, thereby allowing several MAC drivers to be simplfied.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac_select_pcs() allows us to have an explicit point to query which
PCS the MAC wishes to use for a particular PHY interface mode, thereby
allowing us to add support to validate the link settings with the PCS.
Phylink will also use this to select the PCS to be used during a major
configuration event without the MAC driver needing to call
phylink_set_pcs().
Note that if mac_select_pcs() is present, the supported_interfaces
bitmap must be filled in; this avoids mac_select_pcs() being called
with PHY_INTERFACE_MODE_NA when we want to get support for all
interface types. Phylink will return an error in phylink_create()
unless this condition is satisfied.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the legacy flag to indicate whether we should operate in legacy
mode. This allows us to stop using the presence of a PCS as an
indicator to the age of the phylink user, and make PCS presence
optional.
Legacy mode involves:
1) calling mac_config() whenever the link comes up
2) calling mac_config() whenever the inband advertisement changes,
possibly followed by a call to mac_an_restart()
3) making use of mac_an_restart()
4) making use of mac_pcs_get_state()
All the above functionality was moved to a seperate "PCS" block of
operations in March 2020.
Update the documents to indicate that the differences that this flag
makes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tidy up the disable bit clearing where we clear a bit
and then run the link resolver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1ms4Rx-00EKEc-En@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 4904b6ea1f ("net: phy: phylink: Use PHY device interface if
N/A") introduced handling for the phy interface mode where this is not
known at phylink creation time. This was never added to the OF/fwnode
paths, but is necessary when the phy is present in DT, but the phy-mode
is not specified.
Add this handling.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices expose memory-mapped c22-compliant PHYs. Because these
devices do not have an MDIO bus, we cannot use the existing helpers.
Refactor the existing helpers to allow supplying the values for c22
registers directly, instead of using MDIO to access them. Only get_state
and set_advertisement are converted, since they contain the most complex
logic. Because set_advertisement is never actually used outside
phylink_mii_c22_pcs_config, move the MDIO-writing part into that
function. Because some modes do not need the advertisement register set
at all, we use -EINVAL for this purpose.
Additionally, a new function phylink_pcs_enable_an is provided to
determine whether to enable autonegotiation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
1000base-KX was missed in phylink_caps_to_linkmodes(), add it. This
will be necessary to convert stmmac with xpcs to ensure we don't drop
any supported linkmodes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMII has not been documented in the kernel, but information on this PHY
interface mode has been recently found. Document it, and correct the
recently introduced phylink handling for this interface mode.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1mmfVl-0075nP-14@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a generic validate() implementation using the supported_interfaces
and a bitmask of MAC pause/speed/duplex capabilities. This allows us
to entirely eliminate many driver private validate() implementations.
We expose the underlying phylink_get_linkmodes() function so that
drivers which have special needs can still benefit from conversion.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the network device supplies a supported interface bitmap, we can use
that during phylink's validation to simplify MAC drivers in two ways by
using the supported_interfaces bitmap to:
1. reject unsupported interfaces before calling into the MAC driver.
2. generate the set of all supported link modes across all supported
interfaces (used mainly for SFP, but also some 10G PHYs.)
Suggested-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactors the phylink pcs helper functions to use mdiobus_* instead
of mdiodev_*.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The auto-negotiation state in the PCS as set by
phylink_mii_c22_pcs_config was previously always enabled when the
driver is configured for in-band autonegotiation, even if
autonegotiation was disabled on the interface with ethtool. Update the
code to set the BMCR_ANENABLE bit based on the interface's
autonegotiation enabled state.
Update phylink_mii_c22_pcs_get_state to not check
autonegotiation-related fields when autonegotiation is disabled.
Update phylink_mac_pcs_get_state to initialize the state based on the
interface's configured speed, duplex and pause parameters rather than
to unknown when autonegotiation is disabled, before calling the
driver's pcs_get_state functions, as they are not likely to provide
meaningful data for these fields when autonegotiation is disabled. In
this case the driver is really just filling in the link state field.
Note that in cases where there is a downstream PHY connected, such as
with SGMII and a copper PHY, the configuration set by ethtool is
handled by phy_ethtool_ksettings_set and not propagated to the PCS.
This is correct since SGMII or 1000Base-X autonegotiation with the PCS
should normally still be used even if the copper side has disabled it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ea269a6f72 ("net: phylink: Update SFP selected interface on
advertising changes") added a better solution to selecting the
interface mode for SFPs using the advertisement mask. This method will
work for mvneta and mvpp2 when selecting between 2500base-X and
1000base-X without needing to use the basex helper, or indicate that
we support both 1000base-X and 2500base-X when in either of these two
interface modes.
Hence, we need to eliminate the validation prior to selecting the
interface, otherwise when we clean up mvneta's validation function, we
will end up locking to 2500base-X as we validate with an interface mode
of PHY_INERFACE_MODE_2500BASEX.
The supported mask will already have been reduced down to the union of
support for the SFP and MAC already, so we can be confident that the
advertisement mask is already appropriately restricted. We only need to
select the appropriate interface, and then revalidate with the new
interface mode.
We get rid of the check for pl->sfp_port too, this is meaningless here
as it doesn't get cleared when a module is removed, so it doesn't
indicate if a module is present. Just rely on pl->sfp_bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the mdiobus_modify_changed() helper in the C22 PCS advertisement
helper.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper for setting 10Gigabit modes, so we have one central
place that sets all appropriate 10G modes for a driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter points out that we have a code path that permits a NULL
netdev pointer to be passed to netif_carrier_off(), which will cause
a kernel oops. In any case, we need to set pl->old_link_state to false
to have the desired effect when there is no netdev present.
Fixes: f97493657c ("net: phylink: add suspend/resume support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently changes to the advertising state via ethtool do not cause any
reselection of the configured interface mode after the SFP is already
inserted and initially configured.
While it is not typical to change the advertised link modes for an
interface using an SFP in certain use cases it is desirable. In the case
of a SFP port that is capable of handling both SFP and SFP+ modules it
will automatically select between 1G and 10G modes depending on the
supported mode of the SFP. However if the SFP module is capable of
working in multiple modes (e.g. a SFP+ DAC that can operate at 1G or
10G), one end of the cable may be attached to a SFP 1000base-x port thus
the SFP+ end must be manually configured to the 1000base-x mode in order
for the link to be established.
This change causes the ethtool setting of advertised mode changes to
reselect the interface mode so that the link can be established.
Additionally when a module is inserted the advertising mode is reset to
match the supported modes of the module.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang reports that Wake-on-Lan with the stmmac ethernet driver broke
when moving the incorrect handling of mac link state out of mac_config().
This reason this breaks is because the stmmac's WoL is handled by the MAC
rather than the PHY, and phylink doesn't cater for that scenario.
This patch adds the necessary phylink code to handle suspend/resume events
according to whether the MAC still needs a valid link or not. This is the
barest minimum for this support.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to fiddle about with the supported mask after we have
validated the user's requested parameters. Simplify and streamline the
code by moving the linkmode copy and update of the autoneg bit after
validating the user's request.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Augment the phy link debug prints with the pause state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following format issues:
1. open brace '{' following function definitions should go to the next
line.
2. braces {} are not necessary for single line statements.
3. else should follow close brace '}'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Block comments should not use a trailing */ on a separate line and every
line of a block comment should start with an '*'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 25gbase-r interface type and speed to phylink.
This is needed for the Sparx5 switch.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor phylink_of_phy_connect() to use phylink_fwnode_phy_connect().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define phylink_fwnode_phy_connect() to connect phy specified by
a fwnode to a phylink instance.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
if pl->mac_ops->mac_finish() failed, phylink_err should use
"mac_finish" instead of "mac_prepare".
Fixes: b7ad14c2fe ("net: phylink: re-implement interface configuration with PCS")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain platform does not support DT, so we make phylink_parse_mode() to
allow non-DT platform to use it to setup in-band AN advertising.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some functions have different names between their prototypes
and the kernel-doc markup.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Xilinx PCS/PMA PHY requires that BMCR_ISOLATE be disabled for proper
operation in 1000BaseX mode. It should be safe to ensure this bit is
disabled in phylink_mii_c22_pcs_config in all cases.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20201026175802.1332477-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same link partner advertisement word is used for both QSGMII and
SGMII, thus treat both interface modes using the same
phylink_decode_sgmii_word() function.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new addition of the USXGMII link partner ability constants we
can now introduce a phylink helper that decodes the USXGMII word and
populates the appropriate fields in the phylink_link_state structure
based on them.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we intend to use PCS operations, mac_pcs_get_state() will not be
implemented, so will be NULL. If we also intend to register the PCS
operations in mac_prepare() or mac_config(), then this leads to an
attempt to call NULL function pointer during phylink_start(). Avoid
this, but we must report the link is down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface to configure the advertisement for a clause 22 PCS
PHY, and set the AN enable flag in the BMCR appropriately.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a way for MAC PCS to have private data while keeping independence
from struct phylink_config, which is used for the MAC itself. We need
this independence as we will have stand-alone code for PCS that is
independent of the MAC. Introduce struct phylink_pcs, which is
designed to be embedded in a driver private data structure.
This structure does not include a mdio_device as there are PCS
implementations such as the Marvell DSA and network drivers where this
is not necessary.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With PCS support, how we implement interface reconfiguration (or other
major reconfiguration) is not up to the job; we end up reconfiguring
the PCS for an interface change while the link could potentially be up.
In order to solve this, add two additional MAC methods for major
configuration, one to prepare for the change, and one to finish the
change.
This allows mvneta and mvpp2 to shutdown what they require prior to the
MAC and PCS configuration calls, and then restart as appropriate.
This impacts ksettings_set(), which now needs to identify whether the
change is a minor tweak to the advertisement masks or whether the
interface mode has changed, and call the appropriate function for that
update.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-code the pause in-band advertisement update in light of the addition
of PCS support, so that we perform the minimum required; only the PCS
configuration function needs to be called in this case, followed by the
request to trigger a restart of negotiation if the programmed
advertisement changed.
We need to change the pcs_config() signature to pass whether resolved
pause should be passed to the MAC for setups such as mvneta and mvpp2
where doing so overrides the MAC manual flow controls.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For fixed links, we only allow the current settings, so this should be
a matter of merely rejecting an attempt to change the settings. If the
settings agree, then there is nothing more we need to do.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than recomputing whether AN is enabled, use config.an_enabled.
Suggested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have a PHY attached, an ethtool ksettings_set() call only
really needs to call through to the phylib equivalent; phylib will
call back to us when the link changes so we can update our state.
Therefore, we can bypass most of our ksettings_set() call for this
case.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the ksettings_set() implementation to look more like phylib's
implementation; use a switch() for validating the autoneg setting, and
use the linkmode_modify() helper to set the autoneg bit in the
advertisement mask.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling mac_config() when using split PCS, and the interface
remains the same.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only PHYs that are used with phylink which change their interface
are the BCM84881 and MV88X3310 family, both of which only change their
interface modes on link-up events. This will break when drivers are
converted to split-PCS. Fix this.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only PHYs that are used with phylink which change their interface
are the BCM84881 and MV88X3310 family, both of which only change their
interface modes on link-up events. However, rather than relying upon
this behaviour by the PHY, we should give a stronger guarantee when
resolving that the link will be down whenever we change the interface
mode. This patch implements that stronger guarantee for resolve.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a boolean to indicate whether mac_config() should be called during
a resolution. This allows resolution to have a single location where
mac_config() will be called, which will allow us to make decisions
about how and what we do.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejig the link state tracking, so that we can use the current state
in a future patch.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing the ethtool output from phylink and non-phylink fixed-link
setups shows that we have some differences:
- The "auto-negotiation" fields are different; phylink reports these
as "No", non-phylink reports these as "Yes" for the supported and
advertising masks.
- The link partner advertisement is set to the link speed with non-
phylink, but phylink leaves this unset, causing all link partner
fields to be omitted.
The phylink ethtool output also disagrees with the software emulated
PHY dump via the MII registers.
Update the phylink fixed-link parsing code so that we better reflect
the behaviour of the non-phylink code that this facility replaces, and
bring the ethtool interface more into line with the report from via the
MII interface.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are not using in-band autonegotiation, there is no point passing
the request to restart autonegotiation on to the driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface for the phy_speed_(up|down) functions when a driver
makes use of phylink. These pass the call through to phylib when we
have a normal PHY attached (i.o.w., not a PHY on a SFP module.)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been relying on link events and mac_config() when the manual
pause modes are changed. With recent developments, such as moving
the programming of link state to mac_link_up(), this no longer works.
To ensure that we update the MAC, we must generate a link-down followed
by a link-up event; we can do that by setting mac_link_dropped and
triggering a resolve.
Fixes: 91a208f218 ("net: phylink: propagate resolved link config via mac_link_up()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a phylink's ethtool set_pauseparam support deadlock caused by phylib
interacting with phylink: we must not hold the state lock while calling
phylib functions that may call into phylink_phy_change().
Fixes: f904f15ea9 ("net: phylink: allow ethtool -A to change flow control advertisement")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two competing requirements for the devices_in_package field.
We want to use it as a bit array indicating which MMDs are present, but
we also want to know if the Clause 22 registers are present.
Since "devices in package" is a term used in the 802.3 specification,
keep this as the as-specified values read from the PHY, and introduce
a new member "mmds_present" to indicate which MMDs are actually
present in the PHY, derived from the "devices in package" value.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was introduced to allow for different handling of
link up and link down events particularly with regard to the
netif_carrier. The third argument do_carrier allowed the flag to
be left unchanged.
Since then the phylink has introduced an implementation that
completely ignores the third parameter since it never wants to
change the flag and the phylib always sets the third parameter
to true so the flag is always changed.
Therefore the third argument (i.e. do_carrier) is no longer
necessary and can be removed. This also means that the phylib
phy_link_down() function no longer needs its second argument.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the callback into the phylink_config structure, rather than
providing a callback to set this up.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a separate set of PCS operations, which MAC drivers can use to
couple phylink with their associated MAC PCS layer. The PCS
operations include:
- pcs_get_state() - reads the link up/down, resolved speed, duplex
and pause from the PCS.
- pcs_config() - configures the PCS for the specified mode, PHY
interface type, and setting the advertisement.
- pcs_an_restart() - restarts 802.3 in-band negotiation with the
link partner
- pcs_link_up() - informs the PCS that link has come up, and the
parameters of the link. Link parameters are used to program the
PCS for fixed speed and non-inband modes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the bland 'ops' member of struct phylink to be a more
descriptive 'mac_ops' - this is necessary as we're about to introduce
another set of operations.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change phylink_mii_c22_pcs_set_advertisement() to take only the PHY
interface and advertisement mask, rather than the full phylink state.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement helpers for PCS accessed via the MII bus using 802.3 clause
45 cycles for 10GBASE-R. Only link up/down is supported, 10G full
duplex is assumed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement helpers for PCS accessed via the MII bus using 802.3 clause
22 cycles, conforming to 802.3 clause 37 and Cisco SGMII specifications
for the advertisement word.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XLGMII interface and the list of XLGMII speeds to PHYLINK.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may have cases where MAC or PCS do not support Autoneg. Check if it
is supported after validate callback is called.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USXGMII also supports these missing backplane speeds.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should improve the error message when the PHY validate in the MAC
driver failed. I ran into this problem multiple times that I put wrong
interface values into the device tree and was searching why it is
failing with -22 (-EINVAL). This should make it easier to spot the
problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the initial MAC configuration so we get a configuration which
more represents the final operating mode, in particular with respect
to the flow control settings.
We do this by:
1) more fully initialising our phy state, so we can use this as the
initial state for PHY based connections.
2) reading the fixed link state.
3) ensuring that in-band mode has sane pause settings for SGMII vs
802.3z negotiation modes.
In all three cases, we ensure that state->link is false, just in case
any MAC drivers have other ideas by mis-using this member, and we also
take account of manual pause mode configuration at this point.
This avoids MLO_PAUSE_AN being seen in mac_config() when operating in
PHY, fixed mode or inband SGMII mode, thereby giving cleaner semantics
to the pause flags. As a result of this, the pause flags now indicate
in a mode-independent way what is required from a mac_config()
implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ethtool -A is used to change the pause modes, the pause
advertisement is not being changed, but the documentation in
uapi/linux/ethtool.h says we should be. Add that capability to
phylink.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve the fixed link flow control using the recently introduced
linkmode_resolve_pause() helper, which we use in
phylink_get_fixed_state() only when operating in full duplex mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new phy_get_pause() helper to get the resolved pause modes for
a PHY rather than resolving the pause modes ourselves. We temporarily
retain our pause mode resolution for causes where there is no PHY
attached, e.g. for fixed-link modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the application of manually controlled flow control modes from
phylink_resolve_flow(), so that we can use alternative providers of
flow control resolution.
We also want to clear the MLO_PAUSE_AN flag when autoneg is disabled,
since flow control can't be negotiated in this circumstance.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ability for ethtool -A to change the pause settings for
fixed links; if this is really required, we can reinstate it later.
Andrew Lunn agrees: "So I think it is safe to not implement ethtool
-A, at least until somebody has a real use case for it."
Lets avoid making things too complex for use cases that aren't being
used.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
USXGMII supports passing link information in-band between PHY and MAC PCS,
add it to the list of protocols that support in-band AN mode.
Being a MAC-PHY protocol that can auto-negotiate link speeds up to 10
Gbps, we populate the initial supported mask with the entire spectrum of
link modes up to 10G that PHYLINK supports, and we let the driver reduce
that mask in its .phylink_validate method.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, PHYLINK does not put the copper modes for 802.3bz
(NBASE-T) and 802.3an-2006 (10GBASE-T) in the PHY's supported mask, when
the PHY-MAC connection is a 10G-capable one (10GBase-KR, 10GBase-R,
USXGMII). One possible way through which the cable side can work at the
lower speed is by having the PHY emit PAUSE frames towards the MAC. So
fix that omission.
Also include the 2500Base-X fiber mode in this list while we're at it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The information about the PHY attached to the PHYLINK instance is useful
but is missing the IRQ prints that phy_attached_info() adds.
phy_attached_info() is a bit long and it would not be possible to use
phylink_info() anyway.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC PCS blocks are unable to provide interrupts when their status
changes. As we already have support in phylink for polling status, use
this to provide a hook for MACs to enable polling mode.
The patch idea was picked up from Russell King's suggestion on the macb
phylink patch thread here [0] but the implementation was changed.
Instead of introducing a new phylink_start_poll() function, which would
make the implementation cumbersome for common PHYLINK implementations
for multiple types of devices, like DSA, just add a boolean property to
the phylink_config structure, which is just as backwards-compatible.
https://lkml.org/lkml/2019/12/16/603
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QSGMII is a SerDes protocol clocked at 5 Gbaud (4 times higher than
SGMII which is clocked at 1.25 Gbaud), with the same 8b/10b encoding and
some extra symbols for synchronization. Logically it offers 4 SGMII
interfaces multiplexed onto the same physical lanes. Each MAC PCS has
its own in-band AN process with the system side of the QSGMII PHY, which
is identical to the regular SGMII AN process.
So allow QSGMII as a valid in-band AN mode, since it is no different
from software perspective from regular SGMII.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.
The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.
For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of fwnode_get_named_gpiod() that I plan to hide away, let's use
the new fwnode_gpiod_get_index() that mimics gpiod_get_index(), but
works with arbitrary firmware node.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel test robot reports a boot failure with qemu in 5.5-rc,
referencing commit 2203cbf2c8 ("net: sfp: move fwnode parsing into
sfp-bus layer"). This is caused by phylink_create() being passed a
NULL fwnode, causing fwnode_property_get_reference_args() to return
-EINVAL.
Don't attempt to attach to a SFP bus if we have no fwnode, which
avoids this issue.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Fixes: 2203cbf2c8 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e45d1f5288 ("net: phylink: support Clause 45 PHYs on SFP+
modules") added a workaround to support clause 45 PHYs which
dynamically switch their interface mode on SFP+ modules. This was
implemented by validating the PHYs supported/advertising using
PHY_INTERFACE_MODE_NA, rather than the specific interface mode that
we attached the PHY with.
However, we already have a situation where phylink is used to connect
a Marvell 88X3310 PHY which also behaves in exactly the same way, but
which seemingly doesn't need this. The reason seems to be that the
mvpp2 driver sets a whole bunch of link modes for
PHY_INTERFACE_MODE_10GKR down to 10Mb/s, despite 10GBASE-R not actually
supporting anything but 10Gb/s speeds.
When testing with drivers that (correctly) take the mvneta approach,
where the validate() method only returns what can be supported /
advertised for the specified link mode, we find that Clause 45 PHYs do
not behave as we expect: their advertisement is restricted to what
the current link will support, rather than what the PHY supports
through its dynamic switching.
Extend this workaround to all such cases; if we have a Clause 45 PHY
attaching via any means, except in USXGMII, XAUI and RXAUI which are
all unable to support this dynamic switching or have other solutions
to it, then we need to validate using PHY_INTERFACE_MODE_NA.
This should allow mvpp2 to switch to a more conformant validate()
implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing ethtool with the Methode DM7052 module, it was noticed
that attempting to set the advertising mask results in the mask being
truncated to the support offered by the currently chosen PHY interface
mode.
When a PHY dynamically changes the PHY interface mode, limiting the
advertising mask in this way is not correct - if the PHY happened to
negotiate 10GBASE-T, and selected 10GBASE-R as the host interface, we
don't want to restrict the advertisement to just 10GBASE-* modes.
Rework setting the advertisement to take account of this; do not pass
the requested advertisement through phylink_validate(), but rely on
the advertisement restriction (supported mask) set when the PHY was
initially setup.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mismerge between the following two commits:
c678726305 ("net: phylink: ensure consistent phy interface mode")
27755ff88c ("net: phylink: Add phylink_mac_link_{up, down} wrapper functions")
resulted in the wrong interface being passed to the mac_link_up()
function. Fix this up.
Fixes: b4b12b0d2f ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
of_phy_attach() hides the return value of phy_attach_direct(), forcing
us to return a "generic" ENODEV error code that is indistinguishable
from the lack-of-phy-property case.
Switch to using of_phy_find_device() to find the PHY device, and then
propagating any phy_attach_direct() error back to the caller.
Link: https://lore.kernel.org/lkml/20191210113829.GT25745@shell.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The Broadcom BCM84881 does not appear to send the SGMII control word
when operating in SGMII mode, which causes network adapters to fail
to link with the PHY, or decide to operate at fixed 1G speed, even if
the PHY negotiated 100M.
Work around this by detecting the Broadcom BCM84881 and switch to phy
mode rather than inband mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing whether we need to delay the MAC configuration because a module
may have a PHY is useful to phylink to allow NBASE-T modules to work on
systems supporting no more than 2.5G speeds.
This commit allows us to delay such configuration until after the PHY
has been probed by recording the parsed capabilities, and if the module
may have a PHY, doing no more until the module_start() notification is
called. At that point, we either have a PHY, or we don't.
We move the PHY-based setup a little later, and use the PHYs support
capabilities rather than the EEPROM parsed capabilities to determine
whether we can support the PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the configuration step from phylink_sfp_module_insert() so
we can re-use this later.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
