When replenishing, have ipa_endpoint_replenish() allocate a
transaction, and pass that to ipa_endpoint_replenish_one() to fill.
Then, if that produces no error, commit the transaction within the
replenish loop as well. In this way we can distinguish between
transaction failures and buffer allocation/mapping failures.
Failure to allocate a transaction simply means the hardware already
has as many receive buffers as it can hold. In that case we can
break out of the replenish loop because there's nothing more to do.
If we fail to allocate or map pages for the receive buffer, just
try again later.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decide whether the doorbell should be signaled when committing a
replenish transaction in the main replenish loop, rather than in
ipa_endpoint_replenish_one(). This is a step to facilitate the
next patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three spots call ipa_endpoint_replenish(), and just one of those
requests that the backlog be incremented after completing the
replenish operation.
Instead, have the caller increment the backlog, and get rid of the
add_one argument to ipa_endpoint_replenish().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A transaction failure only occurs if no more transactions are
available for an endpoint. It's a very cheap test.
When replenishing an RX endpoint buffer, there's no point in
allocating pages if transactions are exhausted. So don't bother
doing so unless the transaction allocation succeeds.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The replenish_saved field keeps track of the number of times a new
buffer is added to the backlog when replenishing is disabled. We
don't really use it though, so there's no need for us to track it
separately. Whether replenishing is enabled or not, we can simply
increment the backlog.
Get rid of replenish_saved, and initialize and increment the backlog
where it would have otherwise been used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, the IPA hardware needs to request the always-on
subsystem (AOSS) to coordinate with the IPA microcontroller to
retain IPA register values at power collapse. This is done by
issuing a QMP request to the AOSS microcontroller. A similar
request ondoes that request.
We must get and hold the "QMP" handle early, because we might get
back EPROBE_DEFER for that. But the actual request should be sent
while we know the IPA clock is active, and when we know the
microcontroller is operational.
Fixes: 1aac309d32 ("net: ipa: use autosuspend")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Increase the receive buffer size used for data received from the
modem to 32KB, to improve download performance by allowing much
greater aggregation.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow RX endpoints to have differing receive buffer sizes. Define
the receive buffer size in the configuration data, and use that
rather than IPA_RX_BUFFER_SIZE when configuring the endpoint.
Add verification in ipa_endpoint_data_valid_one() that the receive
buffer specified for AP RX endpoints is both big enough to handle at
least one full packet, and not so big in an aggregating endpoint
that its size can't be represented when programming the hardware.
Move aggr_byte_limit_max() up in "ipa_endpoint.c" so it can be used
earlier in the file without a forward-reference.
Initially we'll just keep the 8KB receive buffer size already in use
for all AP RX endpoints..
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have seen cases where an endpoint RX completion interrupt arrives
while replenishing for the endpoint is underway. This causes another
instance of replenishing to begin as part of completing the receive
transaction. If this occurs it can lead to transaction corruption.
Use a new flag to ensure only one replenish instance for an endpoint
executes at a time.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new replenish_flags bitmap to contain Boolean flags
associated with an endpoint's replenishing state. Replace the
replenish_enabled field with a flag in that bitmap. This is to
prepare for the next patch, which adds another flag.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_replenish(), if an error occurs when attempting to
replenish a receive buffer, we just quit and try again later. In
that case we increment the backlog count to reflect that the attempt
was unsuccessful. Then, if the add_one flag was true we increment
the backlog again.
This second increment is not included in the backlog local variable
though, and its value determines whether delayed work should be
scheduled. This is a bug.
Fix this by determining whether 1 or 2 should be added to the
backlog before adding it in a atomic_add_return() call.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the definition of the IPA interconnects for IPA v4.5 so
the path between IPA and system memory is represented by a single
"memory" interconnect.
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA v4.2 introduced GSI channel flow control, used instead of IPA
endpoint DELAY mode to prevent a TX channel from injecting packets
into the IPA core. It used a new FLOW_CONTROLLED channel state
which could be entered using GSI generic commands.
IPA v4.11 extended the channel flow control model. Rather than
having a distinct FLOW_CONTROLLED channel state, each channel has a
"flow control" property that can be enabled or not--independent of
the channel state. The AP (or modem) can modify this property using
the same GSI generic commands as before.
The AP only uses channel flow control on modem TX channels, and only
when recovering from a modem crash. The AP has no way to discover
the state of a modem channel, so the fact that (starting with IPA
v4.11) flow control no longer uses a distinct channel state is
invisible to the AP. So enhanced flow control generally does not
change the way AP uses flow control.
There are a few small differences, however:
- There is a notion of "primary" or "secondary" flow control, and
when enabling or disabling flow control that must be specified
in a new field in the GSI generic command register. For now, we
always specify 0 (meaning "primary").
- When disabling flow control, it's possible a request will need
to be retried. We retry up to 5 times in this case.
- Another new generic command allows the current flow control
state to be queried. We do not use this.
Other than the need for retries, the code essentially works the same
way as before.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
One quirk for certain versions of IPA is that endpoint DELAY mode
does not work properly. IPA DELAY mode prevents any packets from
being delivered to the IPA core for processing on a TX endpoint.
The AP uses DELAY mode when the modem crashes, to prevent modem TX
endpoints from generating traffic during crash recovery. Without
this, there is a chance the hardware will stall during recovery from
a modem crash.
To achieve a similar effect, a GSI FLOW_CONTROLLED channel state
was created. A STARTED TX channel can be placed in FLOW_CONTROLLED
state, which prevents the transfer of any more packets. A channel
in FLOW_CONTROLLED state can be either returned to STARTED state, or
can be transitioned to STOPPED state.
Because this operates on GSI channels, two generic commands were
added to allow the AP to control this state for modem channels
(similar to the ALLOCATE and HALT channel commands).
Previously the code assumed this quirk only applied to IPA v4.2.
In fact, channel flow control (rather than endpoint DELAY mode)
should be used for all versions *starting* with IPA v4.2.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dummy net_device is a large field in the GSI structure, but it
is not at all interesting from the perspective of debugging. Move
it to the end of the GSI structure so the other fields are easier to
find in memory.
The channel and event ring arrays are also very large, so move them
near the end of the structure as well.
Swap the position of the result and completion fields to improve
structure packing.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A mutex ensures we never submit more than one GSI command of any
kind at once. This means the per-channel and per-event ring
completion structures provide no benefit. Instead, just use the
single (existing) GSI completion to signal the completion of GSI
commands of all types.
This makes gsi_evt_ring_init() a trivial function with no inverse,
so open-code it in its sole caller and get rid of the function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_endpoint_skb_copy(), a new socket buffer structure is
allocated so that some data can be copied into it. However, after
doing this, if the endpoint has a null netdev pointer, we just drop
free the socket buffer.
Instead, check endpoint->netdev pointer first, and just return early
if it's null. Also return early if the SKB allocation fails, to
avoid the deeper indentation in the normal path.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During setup, ipa_endpoint_program() programs each endpoint with
various configuration parameters. One of those registers defines
whether to drop packets when a head-of-line blocking condition is
detected on an RX endpoint. We currently assume this is disabled;
instead, explicitly set it to be disabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The head-of-line block (HOLB) drop timer is only meaningful when
dropping packets due to blocking is enabled. Given that, redefine
the interface so the timer is specified when enabling HOLB drop, and
use a different function when disabling.
To enable and disable HOLB drop, these functions will now be used:
ipa_endpoint_init_hol_block_enable(endpoint, milliseconds)
ipa_endpoint_init_hol_block_disable(endpoint)
The existing ipa_endpoint_init_hol_block_enable() becomes a helper
function, renamed ipa_endpoint_init_hol_block_en(), and used with
ipa_endpoint_init_hol_block_timer() to enable HOLB block on an
endpoint.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Not all filter table entries are used. Only certain endpoints
support filtering, and the table begins with a bitmap indicating
which endpoints use the "slots" that follow for filter rules.
Currently, unused filter table entries are not initialized.
Instead, zero-fill the entire unused portion of the filter table
memory regions, to make it more obvious that memory is unused (and
not subsequently modified).
This is not strictly necessary, but the result is reassuring when
looking at filter table memory.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent commit made disabling the SMP2P "setup ready" interrupt
unrelated to ipa_modem_stop(). Given that, it seems fitting to get
rid of ipa_modem_init() and ipa_modem_exit() (which are trivial
wrapper functions), and call ipa_smp2p_init() and ipa_smp2p_exit()
directly instead.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Calling ipa_cmd_pipeline_clear() after stopping the channel
underlying the AP<-modem RX endpoint can lead to a deadlock.
This occurs in the ->runtime_suspend device power operation for the
IPA driver. While this callback is in progress, any other requests
for power will block until the callback returns.
Stopping the AP<-modem RX channel does not prevent the modem from
sending another packet to this endpoint. If a packet arrives for an
RX channel when the channel is stopped, an SUSPEND IPA interrupt
condition will be pending. Handling an IPA interrupt requires
power, so ipa_isr_thread() calls pm_runtime_get_sync() first thing.
The problem occurs because a "pipeline clear" command will not
complete while such a SUSPEND interrupt condition exists. So the
SUSPEND IPA interrupt handler won't proceed until it gets power;
that won't happen until the ->runtime_suspend callback (and its
"pipeline clear" command) completes; and that can't happen while
the SUSPEND interrupt condition exists.
It turns out that in this case there is no need to use the "pipeline
clear" command. There are scenarios in which clearing the pipeline
is required while suspending, but those are not (yet) supported
upstream. So a simple fix, avoiding the potential deadlock, is to
stop calling ipa_cmd_pipeline_clear() in ipa_endpoint_suspend().
This removes the only user of ipa_cmd_pipeline_clear(), so get rid
of that function. It can be restored again whenever it's needed.
This is basically a manual revert along with an explanation for
commit 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()").
Fixes: 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPA setup_complete flag is set at the end of ipa_setup(), when
the setup phase of initialization has completed successfully. This
occurs as part of driver probe processing, or (if "modem-init" is
specified in the DTS file) it is triggered by the "ipa-setup-ready"
SMP2P interrupt generated by the modem.
In the latter case, it's possible for driver shutdown (or remove) to
begin while setup processing is underway, and this can't be allowed.
The problem is that the setup_complete flag is not adequate to signal
that setup is underway.
If setup_complete is set, it will never be un-set, so that case is
not a problem. But if setup_complete is false, there's a chance
setup is underway.
Because setup is triggered by an interrupt on a "modem-init" system,
there is a simple way to ensure the value of setup_complete is safe
to read. The threaded handler--if it is executing--will complete as
part of a request to disable the "ipa-modem-ready" interrupt. This
means that ipa_setup() (which is called from the handler) will run
to completion if it was underway, or will never be called otherwise.
The request to disable the "ipa-setup-ready" interrupt is currently
made within ipa_modem_stop(). Instead, disable the interrupt
outside that function in the two places it's called. In the case of
ipa_remove(), this ensures the setup_complete flag is safe to read
before we read it.
Rename ipa_smp2p_disable() to be ipa_smp2p_irq_disable_setup(), to be
more specific about its effect.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently maintain a "disabled" Boolean flag to determine whether
the "ipa-setup-ready" SMP2P IRQ handler does anything. That flag
must be accessed under protection of a mutex.
Instead, disable the SMP2P interrupt when requested, which prevents
the interrupt handler from ever being called. More importantly, it
synchronizes a thread disabling the interrupt with the completion of
the interrupt handler in case they run concurrently.
Use the IPA setup_complete flag rather than the disabled flag in the
handler to determine whether to ignore any interrupts arriving after
the first.
Rename the "disabled" flag to be "setup_disabled", to be specific
about its purpose.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'for_each_clear_bit()' instead of hand writing it. It is much less
version.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The head-of-line blocking timer should only be modified when
head-of-line drop is disabled.
One of the steps in recovering from a modem crash is to enable
dropping of packets with timeout of 0 (immediate). We don't know
how the modem configured its endpoints, so before we program the
timer, we need to ensure HOL_BLOCK is disabled.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with IPA v4.5, the HOL_BLOCK_EN register must be written
twice when enabling head-of-line blocking avoidance.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The source group count was mistakenly assigned to both dst and src loops.
Fix it to make IPA probe and work again.
Fixes: 4fd704b360 ("net: ipa: record number of groups in data")
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20211111183724.593478-1-konrad.dybcio@somainline.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The
fix we agreed on in the end is to make this symbol selected by any
driver using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in v5.15.
There is a small merge conflict against an earlier partial fix for the
QCOM_SCM dependency problems.
Finally, the branch also includes a small unrelated build fix for NOMMU
architectures.
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=187C
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is an off-by-one problem in ipa_table_init_add(), when
initializing filter tables.
In that function, the number of filter table entries is determined
based on the number of set bits in the filter map. However that
count does *not* include the extra "slot" in the filter table that
holds the filter map itself. Meanwhile, ipa_table_addr() *does*
include the filter map in the memory it returns, but because the
count it's provided doesn't include it, it includes one too few
table entries.
Fix this by including the extra slot for the filter map in the count
computed in ipa_table_init_add().
Note: ipa_filter_reset_table() does not have this problem; it resets
filter table entries one by one, but does not overwrite the filter
bitmap.
Fixes: 2b9feef2b6 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, rename "ipa_clock.c" to be "ipa_power.c" and "ipa_clock.h"
to be "ipa_power.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename a number of functions to clarify that there is no longer a
notion of an "IPA clock," but rather that the functions are more
generally related to IPA power management.
ipa_clock_enable() -> ipa_power_enable()
ipa_clock_disable() -> ipa_power_disable()
ipa_clock_rate() -> ipa_core_clock_rate()
ipa_clock_init() -> ipa_power_init()
ipa_clock_exit() -> ipa_power_exit()
Rename the ipa_clock structure to be ipa_power. Rename all
variables and fields using that structure type "power" rather
than "clock".
Rename the ipa_clock_data structure to be ipa_power_data, and more
broadly, just substitute "power" for "clock" in places that
previously represented things related to the "IPA clock".
Update comments throughout.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use runtime power management autosuspend.
Up until this point, we only suspended the IPA hardware for system
suspend; now we'll suspend it aggressively using runtime power
management, setting the initial autosuspend delay to half a second
of inactivity.
Replace pm_runtime_put() calls with pm_runtime_put_autosuspend(),
call pm_runtime_mark_last_busy() before each of those. In places
where we're shutting things down, or decrementing power references
for errors, use pm_runtime_put_noidle() instead.
Finally, remove ipa_runtime_idle(), so the ->runtime_suspend
callback will occur if idle.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only remaining user of the ipa_clock_{get,put}() interface is
ipa_isr_thread(). Replace calls to ipa_clock_get() there calling
pm_runtime_get_sync() instead. And call pm_runtime_put() there
rather than ipa_clock_put(). Warn if we ever get an error.
With that, we can get rid of ipa_clock_get() and ipa_clock_put().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we open or close the modem network device we need to ensure the
hardware is powered. Replace the callers of ipa_clock_get() found
in ipa_open() and ipa_stop() with calls to pm_runtime_get_sync().
If an error is returned, simply return that error to the caller
(without any error or warning message). This could conceivably
occur if the function was called while the system was suspended,
but that really shouldn't happen. Replace corresponding calls to
ipa_clock_put() with pm_runtime_put() also.
If the modem crashes we also need to ensure the hardware is powered
to recover. If getting power returns an error there's not much we
can do, but at least report the error. (Ideally the remoteproc SSR
code would ensure the AP was not suspended when it sends the
notification, but that is not (yet) the case.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the ipa_clock_get() call in ipa_uc_clock() when taking the
"proxy" clock reference for the microcontroller with a call to
pm_runtime_get_sync(). Replace calls of ipa_clock_put() for the
microcontroller with pm_runtime_put() calls instead.
There is a chance we get an error when taking the microcontroller
power reference. This is an unlikely scenario, where system suspend
is initiated just before we learn the modem is booting. For now
we'll just accept that this could occur, and report it if it does.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the "modem-init" Device Tree property is present for a platform,
the modem performs early IPA hardware initialization, and signals
this is complete with an "ipa-setup-ready" SMP2P interrupt. This
triggers a call to ipa_setup(), which requires the hardware to be
powered.
Replace the call to ipa_clock_get() in this case with a call to
pm_runtime_get_sync(). And replace the corresponding calls to
ipa_clock_put() with calls to pm_runtime_put() instead.
There is a chance we get an error when taking this power reference.
This is an unlikely scenario, where system suspend is initiated just
before the modem signals it has finished initializing the IPA
hardware. For now we'll just accept that this could occur, and
report it if it does.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need the hardware to be powered starting at the config stage of
initialization when the IPA driver probes. And we need it powered
when the driver is removed, at least until the deconfig stage has
completed.
Replace callers of ipa_clock_get() in ipa_probe() and ipa_exit(),
calling pm_runtime_get_sync() instead. Replace the corresponding
callers of ipa_clock_put(), calling pm_runtime_put() instead.
The only error we expect when getting power would occur when the
system is suspended. The ->probe and ->remove driver callbacks
won't be called when suspended, so issue a WARN() call if an error
is seen getting power.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski pointed out a race condition in ipa_start_xmit() in a
recently-accepted series of patches:
https://lore.kernel.org/netdev/20210812195035.2816276-1-elder@linaro.org/
We are stopping the modem TX queue in that function if the power
state is not active. We restart the TX queue again once hardware
resume is complete.
TX path Power Management
------- ----------------
pm_runtime_get(); no power Start resume
Stop TX queue ...
pm_runtime_put() Resume complete
return NETDEV_TX_BUSY Start TX queue
pm_runtime_get()
Power present, transmit
pm_runtime_put() (auto-suspend)
The issue is that the power management (resume) activity and the
network transmit activity can occur concurrently, and there's a
chance the queue will be stopped *after* it has been started again.
TX path Power Management
------- ----------------
Resume underway
pm_runtime_get(); no power ...
Resume complete
Start TX queue
Stop TX queue <-- No more transmits after this
pm_runtime_put()
return NETDEV_TX_BUSY
We address this using a STARTED flag to indicate when the TX queue
has been started from the resume path, and a spinlock to make the
flag and queue updates happen atomically.
TX path Power Management
------- ----------------
Resume underway
pm_runtime_get(); no power Resume complete
start TX queue \
If STARTED flag is *not* set: > atomic
Stop TX queue set STARTED flag /
pm_runtime_put()
return NETDEV_TX_BUSY
A second flag is used to address a different race that involves
another path requesting power.
TX path Other path Power Management
------- ---------- ----------------
pm_runtime_get_sync() Resume
Start TX queue \ atomic
Set STARTED flag /
(do its thing)
pm_runtime_put()
(auto-suspend)
pm_runtime_get() Mark delayed resume
STARTED *is* set, so
do *not* stop TX queue <-- Queue should be stopped here
pm_runtime_put()
return NETDEV_TX_BUSY Suspend done, resume
Resume complete
pm_runtime_get()
Stop TX queue
(STARTED is *not* set) Start TX queue \ atomic
pm_runtime_put() Set STARTED flag /
return NETDEV_TX_BUSY
So a STOPPED flag is set in the transmit path when it has stopped
the TX queue, and this pair of operations is also protected by the
spinlock. The resume path only restarts the TX queue if the STOPPED
flag is set. This case isn't a major problem, but it avoids the
"non-trivial amount of useless work" done by the networking stack
when NETDEV_TX_BUSY is returned.
Fixes: 6b51f802d6 ("net: ipa: ensure hardware has power in ipa_start_xmit()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a clock reference is taken whenever the ->ndo_open
callback for the modem netdev is called. That reference is dropped
when the device is closed, in ipa_stop().
We no longer need this, because ipa_start_xmit() now handles the
situation where the hardware power state is not active.
Drop the clock reference in ipa_open() when we're done, and take a
new reference in ipa_stop() before we begin closing the interface.
Finally (and unrelated, but trivial), change the return type of
ipa_start_xmit() to be netdev_tx_t instead of int.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we stop the modem netdev transmit queue when suspending
the hardware. For system suspend this ensured we'd never attempt
to transmit while attempting to suspend the modem endpoints.
For runtime suspend, the IPA hardware might get suspended while the
system is operating. In that case we want an attempt to transmit a
packet to cause the hardware to resume if necessary. But if we
disable the queue this cannot happen.
So stop disabling the queue on suspend. In case we end up disabling
it in ipa_start_xmit() (see the previous commit), we still arrange
to start the TX queue on resume.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure the hardware is powered when we transmit a packet.
But if it's not, we can't block to wait for it. So asynchronously
request power in ipa_start_xmit(), and only proceed if the return
value indicates the power state is active.
If the hardware is not active, a runtime resume request will have
been initiated. In that case, stop the network stack from further
transmit attempts until the resume completes. Return NETDEV_TX_BUSY,
to retry sending the packet once the queue is restarted.
If the power request returns an error (other than -EINPROGRESS,
which just means a resume requested elsewhere isn't complete), just
drop the packet.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new work structure in the modem private data, and use it to
re-enable the modem network device transmit queue when resuming.
This is needed by the next patch, which stops the TX queue if IPA
power isn't active when a transmit request arrives. Packets will
start arriving the instant the TX queue is enabled, but resuming
isn't complete until ipa_modem_resume() returns. This way we're
sure to be resumed before transmits are allowed again.
Cancel it before calling ipa_stop() in ipa_modem_stop() to ensure
the transmit queue restart completes before it gets stopped there.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new flag that is set when the hardware is suspended due to a
system suspend operation, distingishing it from runtime suspend.
Use it in the SUSPEND IPA interrupt handler to determine whether to
trigger a system resume because of the event. Define new suspend
and resume power management callback functions to set and clear the
new flag, respectively.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to enable the IPA interrupt as a wakeup interrupt into
ipa_power_setup(), disable it in ipa_power_teardown().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't required, but all callers of ipa_aggr_granularity_val()
pass a constant value (IPA_AGGR_GRANULARITY) as the usec argument.
Two of those callers are in ipa_validate_build(), with the result
being passed to BUILD_BUG_ON().
Evidently the "sparc64-linux-gcc" compiler (at least) doesn't always
inline ipa_aggr_granularity_val(), so the result of the function is
not constant at compile time, and that leads to build errors.
Define the function with the __always_inline attribute to avoid the
errors. We can see by inspection that the value passed is never
zero, so we can just remove its WARN_ON() call.
Fixes: 5bc5588466 ("net: ipa: use WARN_ON() rather than assertions")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210811135948.2634264-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that ipa_clock_get_additional() is a trivial wrapper around
pm_runtime_get_if_active(), just open-code it in its only caller
and delete the function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The runtime power management core code maintains a usage count. This
count mirrors the IPA clock reference count, and there's no need to
maintain both. So get rid of the IPA clock reference count and just
rely on the runtime PM usage count to determine when the hardware
should be suspended or resumed.
Use pm_runtime_get_if_active() in ipa_clock_get_additional(). We
care whether power is active, regardless of whether it's in use, so
pass true for its ign_usage_count argument.
The IPA clock mutex is just used to make enabling/disabling the
clock and updating the reference count occur atomically. Without
the reference count, there's no need for the mutex, so get rid of
that too.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suspending the IPA hardware is now managed by the runtime PM core
code. The ->runtime_idle callback returns a non-zero value, so it
will never suspend except when forced. As a result, there's no need
to take an extra "do not suspend" clock reference.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the runtime power management core to cause hardware suspend and
resume to occur. Enable it in ipa_clock_init() (without autosuspend),
and disable it in ipa_clock_exit().
Use ipa_runtime_suspend() as the ->runtime_suspend power operation,
and arrange for it to be called by having ipa_clock_get() call
pm_runtime_get_sync() when the first clock reference is taken.
Similarly, use ipa_runtime_resume() as the ->runtime_resume power
operation, and pm_runtime_put() when the last IPA clock reference
is dropped.
Introduce ipa_runtime_idle() as the ->runtime_idle power operation,
and have it return a non-zero value; this way suspend will never
occur except when forced.
Use pm_runtime_force_suspend() and pm_runtime_force_resume() as the
system suspend and resume callbacks, and remove ipa_suspend() and
ipa_resume().
Store a pointer to the device structure passed to ipa_clock_init(),
so it can be used by ipa_clock_exit() to disable runtime power
management.
For now we preserve IPA clock reference counting.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce ipa_runtime_suspend() and ipa_runtime_resume(), which
encapsulate the activities necessary for suspending and resuming
the IPA hardware. Call these functions from ipa_clock_get() and
ipa_clock_put() when the first reference is taken or last one is
dropped.
When the very first clock reference is taken (for ipa_config()),
setup isn't complete yet, so (as before) only the core clock gets
enabled.
When the last clock reference is dropped (after ipa_deconfig()),
ipa_teardown() will have made the setup_complete flag false, so
there too, the core clock will be stopped without affecting GSI
or the endpoints.
Otherwise these new functions will perform the desired suspend and
resume actions once setup is complete.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable the IPA clock rather than dropping a reference to it in the
system suspend callback. This forces the suspend to occur without
affecting existing references.
Similarly, enable the clock rather than taking a reference in
ipa_resume(), forcing a resume without changing the reference count.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently assume no errors occur when enabling or disabling the
IPA core clock and interconnects. And although this commit exposes
errors that could occur, we generally assume this won't happen in
practice.
This commit changes ipa_clock_get() and ipa_clock_put() so each
returns a value. The values returned are meant to mimic what the
runtime power management functions return, so we can set up error
handling here before we make the switch. Have ipa_clock_get()
increment the reference count even if it returns an error, to match
the behavior of pm_runtime_get().
More details follow.
When taking a reference in ipa_clock_get(), return 0 for the first
reference, 1 for subsequent references, or a negative error code if
an error occurs. Note that if ipa_clock_get() returns an error, we
must not touch hardware; in some cases such errors now cause entire
blocks of code to be skipped.
When dropping a reference in ipa_clock_put(), we return 0 or an
error code. The error would come from ipa_clock_disable(), which
now returns what ipa_interconnect_disable() returns (either 0 or a
negative error code). For now, callers ignore the return value;
if an error occurs, a message will have already been logged, and
little more can actually be done to improve the situation.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipa->flags field is only ever used in "ipa_clock.c", related to
suspend/resume activity.
Move the definition of the ipa_flag enumerated type to "ipa_clock.c".
And move the flags field from the ipa structure and to the ipa_clock
structure. Rename the type and its values to include "power" or
"POWER" in the name.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ipa_suspend_handler() into "ipa_clock.c" from "ipa_main.c", to
group with the reset of the suspend/resume code. This IPA interrupt
is triggered if an IPA RX endpoint is suspended but has a packet to
be delivered.
Introduce ipa_power_setup() and ipa_power_teardown() to add and
remove the handler for the IPA SUSPEND interrupt at the same place
as before, while allowing the handler to remain private.
The "power" naming convention will be adopted elsewhere in this
file as well (soon).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ipa_suspend() and ipa_resume(), as well as the definition of
the ipa_pm_ops structure into "ipa_clock.c". Make ipa_pm_ops public
and declare it as extern in "ipa_clock.h".
This is part of centralizing IPA power management functionality into
"ipa_clock.c" (the file will eventually get a name change).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange messages reported when errors occur in the IPA clock code,
so that the specific interconnect is identified when an error occurs
enabling or disabling it, or the core clock is indicated when an
error occurs enabling it.
Have ipa_interconnect_disable() return zero or the negative error
value returned by the first interconnect that produced an error
when disabled. For now, the callers ignore the returned value.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign the ipa->modem_netdev and endpoint->netdev pointers *before*
registering the network device. As soon as the device is
registered it can be opened, and by that time we'll want those
pointers valid.
Similarly, don't make those pointers NULL until *after* the modem
network device is unregistered in ipa_modem_stop().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The modem network device is set up by ipa_modem_start(). But its
TX queue is not actually started and endpoints enabled until it is
opened.
So avoid stopping the modem network device TX queue and disabling
endpoints on suspend or stop unless the netdev is marked UP. And
skip attempting to resume unless it is UP.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three interconnects are defined for IPA version 4.9, but there
should only be two. They should also use names that match what's
used for other platforms (and specified in the Device Tree binding).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new functions gsi_suspend() and gsi_resume(), which will
disable the GSI interrupt handler after all endpoints are suspended
and re-enable it before endpoints are resumed. This will ensure no
GSI interrupt handler will fire when the hardware is suspended.
Here's a little further explanation. There are seven GSI interrupt
types, and most are disabled except when needed.
- These two are not used (never enabled):
GSI_INTER_EE_CH_CTRL
GSI_INTER_EE_EV_CTRL
- These two are only used to implement channel and event ring
commands, and are only enabled while a command is underway:
GSI_CH_CTRL
GSI_EV_CTRL
- The IEOB interrupt signals I/O completion. It will not fire
when a channel is stopped (or "suspended").
GSI_IEOB
- This interrupt is used to allocate or halt modem channels,
and is only enabled while such a command is underway.
GSI_GLOB_EE
However it also is used to signal certain errors, and this could
occur at any time.
- The general interrupt signals general errors, and could occur at
any time.
GSI_GENERAL
The purpose for this change is to ensure no global or general
interrupts fire due to errors while the hardware is suspended.
We enable the clock on resume, and at that time we can "handle"
(at least report) these error conditions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI IRQ handler could be triggered as soon as it is registered
with request_irq(). The handler function, gsi_isr(), touches
hardware, meaning the IPA clock must be operational. The IPA clock
is not operating when the handler is registered (in gsi_irq_init()),
so this is a problem.
Move the call to request_irq() for the GSI interrupt handler into
gsi_irq_setup(), which is called when the IPA clock is known to be
operational (and furthermore, the GSI firmware will have been
loaded). Request the IRQ at the end of that function, after all
interrupt types have been disabled and masked.
Move the matching free_irq() call into gsi_irq_teardown(), and get
rid of the now empty gsi_irq_exit(),
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change gsi_irq_setup() so it returns an error value, and introduce
gsi_irq_teardown() as its inverse. Set the interrupt type (IRQ
rather than MSI) in gsi_irq_setup().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move gsi_irq_setup() and gsi_ring_setup() so they're defined right
above gsi_setup() where they're called. This is a trivial movement
of code to prepare for upcoming patches.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the Boolean flags passed to __gsi_channel_start() and
__gsi_channel_stop() so they represent whether the request is being
made to implement suspend (versus stop) or resume (versus start).
Then stop or start the channel for suspend/resume requests only if
the hardware version indicates it should be done.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI layer has the IPA version now, so there's no need for
version-specific flags to be passed from IPA. One instance of
this is in gsi_channel_suspend() and gsi_channel_resume(), which
indicate whether or not the endpoint suspend is implemented by
GSI stopping the channel. We can make that determination based
on gsi->version, eliminating the need for a Boolean flag in those
functions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until we complete the setup stage of initialization, GSI is not
initialized and therefore endpoints aren't usable. So avoid
suspending endpoints during system suspend unless setup is complete.
Clear the setup_complete flag at the top of ipa_teardown() to
reflect the fact that things are no longer in setup state.
Get rid of a misplaced (and superfluous) comment.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPA network device can be opened at any time, and an opened
network device can be stopped any time. Both of these callback
functions require access to the hardware, and therefore they need
the IPA clock to be operational. Take an IPA clock reference in
both the ->open and ->stop callback functions, dropping the
reference when they are done accessing hardware.
The ->start_xmit callback requires a little different handling,
and that will be added separately.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remoteproc SSR callback function for the modem requires hardware
access when handling a modem crash or shutdown. Take and later
release an IPA clock reference in ipa_modem_crashed(), to ensure the
hardware is operational.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two places call ipa_setup(). The first, ipa_probe(), holds an IPA
clock reference when calling ipa_setup() (if the AP is responsible
for IPA firmware loading). But if the modem is loading IPA
firmware, ipa_smp2p_modem_setup_ready_isr() calls ipa_setup() after
the modem has signaled the hardware is ready. This can happen at
any time, and there is no guarantee the hardware is active.
Have ipa_smp2p_modem_setup() take an IPA clock reference before it
calls ipa_setup(), and release it once setup is complete.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any entry point that leads to IPA hardware access must ensure the
hardware is operational (clocked). Currently we ensure this by
taking an extra clock reference during setup that is not released
until we receive a system suspend request. But this extra reference
will soon go away.
When the platform driver ->probe function is called, we first need
hardware access in ipa_config(). Although ipa_config() takes an IPA
clock reference, it the special reference taken to prevent suspending
the hardware.
Have ipa_probe() take a reference before calling ipa_config(), so
that the "no-suspend" reference can eventually go away. Drop this
reference before ipa_probe() returns.
Similarly, the driver ->remove function can be called at any time.
Take an IPA clock reference at the beginning of that function, and
drop it again after the deconfig stage has completed (at which point
hardware access is no longer needed).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ipa_isr_thread() is a simple wrapper that gets a clock
reference around ipa_interrupt_process_all(), get rid of the
called function and just open-code it in ipa_isr_thread().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pending IPA interrupts are checked by ipa_isr_thread(), and
interrupts are processed only if an enabled interrupt has a
condition pending. But ipa_interrupt_process_all() now makes the
same check, so the one in ipa_isr_thread() can just be skipped.
Also in ipa_isr_thread(), any interrupt conditions pending which are
not enabled are cleared. Here too, ipa_interrupt_process_all() now
clears such excess interrupt conditions, so ipa_isr_thread() doesn't
have to.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We ignore any IPA interrupt that has no handler. If any interrupt
conditions without a handler exist when an IPA interrupt occurs,
clear those conditions. Add a debug message to report which ones
are being cleared.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the IPA interrupt handler runs, the IPA core clock must already
be operational, and the interconnect providing access by the AP to
IPA config space must be enabled too.
Currently we ensure this by taking a top-level "stay awake" IPA
clock reference, but that will soon go away. In preparation for
that, move all handling for the IPA IRQ into the thread function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first time it's booted, the modem loads and starts the
IPA-resident microcontroller. Once the microcontroller has
completed its initialization, it notifies the AP it's "ready"
by sending an INIT_COMPLETED response message.
Until it receives that microcontroller message, the AP must ensure
the IPA core clock remains operational. Currently, a "proxy" clock
reference is taken in ipa_uc_config(), dropping it again once the
message is received.
However there could be a long delay between when ipa_config()
completes and when modem actually starts. And because the
microcontroller gets loaded by the modem, there's no need to
get the modem "proxy clock" until the first time it starts.
Create a new function ipa_uc_clock() which takes the "proxy" clock
reference for the microcontroller. Call it when we get remoteproc
SSR notification that the modem is about to start. Keep an
additional flag to record whether this proxy clock reference needs
to be dropped at shutdown time, and issue a warning if we get the
microcontroller message either before the clock reference is taken,
or after it has already been dropped.
Drop the nearby use of "hh" length modifiers, which are no longer
encouraged in the kernel.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initializing up the IPA-resident microcontroller requires the IPA
clock, and sets up two IPA interrupt handlers, but this does not
require GSI access. The interrupt handlers also require the clock
to be enabled, and require the IPA memory regions to be configured,
but neither requires GSI access. As a result, the microcontroller
can be initialized during the "config" rather than "setup" phase of
IPA initialization.
Initialize the microcontroller in ipa_config() rather than
ipa_setup(), and rename the called function ipa_uc_config().
Do the inverse in ipa_deconfig() rather than ipa_teardown(),
and rename the function for that case ipa_uc_deconfig().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialization of the IPA driver has several phases:
- "init" phase can be done without any access to IPA hardware
- "config" phase requires the IPA hardware to be clocked
- "setup" phase requires the GSI layer to be functional
Currently, initialization for the IPA interrupt handling code occurs
in the setup phase. It requires access to the IPA hardware but does
not need GSI, so it can be moved to the config phase instead.
Call the interrupt configuration function early in ipa_config()
rather than from ipa_setup(). Rename ipa_interrupt_setup() to be
ipa_interrupt_config(), and ipa_interrupt_teardown() to be
ipa_interupt_deconfig(), so their names properly indicate when
they get called.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA-resident memory is one of the most primitive resources that
needs initialization, so call init_mem_config() early in
ipa_config().
This is in preparation for initializing the IPA-resident
microcontroller earlier.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions ipa_modem_setup() and ipa_modem_teardown() are trivial
wrappers that call ipa_qmi_setup() and ipa_qmi_teardown(). Just
call the QMI functions directly, and get rid of the wrappers.
Improve the documentation of what setting up QMI does.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RMNet and IPA drivers both support inline checksum offload now.
So enable it for the TX and RX modem endoints for IPA version 4.5+.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've added commented assertions to record certain properties that
can be assumed to hold in certain places in the IPA code. Convert
these into real WARN_ON() calls so the assertions are actually
checked, using the standard WARN_ON() mechanism.
Where errors can be returned, return an error if a warning is
triggered.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are only a few remaining spots that validate IPA code
conditional on whether a symbol is defined at compile time.
The checks are not expensive, so just build them always.
This completes the removal of all CONFIG_VALIDATE/CONFIG_VALIDATION
IPA code.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All checks in ipa_table_validate_build() are computed at build time,
so build that unconditionally.
In ipa_table_valid() calls to ipa_table_valid_one() are missing the
IPA pointer parameter is missing in (a bug that shows up only when
IPA_VALIDATE is defined). Don't bother checking whether hashed
table memory regions are valid if hashed tables are not supported.
With those things fixed, have these table validation functions built
unconditionally (not dependent on IPA_VALIDATE).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop supporting different sizes for hashed and non-hashed filter or
route tables. Add BUILD_BUG_ON() calls to verify the sizes of the
fields in the filter/route table initialization immediate command
are the same.
Add a check to ipa_cmd_table_valid() to ensure the size of the
memory region being checked fits within the immediate command field
that must hold it.
Remove two Boolean parameters used only for error reporting. This
actually fixes a bug that would only show up if IPA_VALIDATE were
defined. Define ipa_cmd_table_valid() unconditionally (no longer
dependent on IPA_VALIDATE).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently three interconnects are defined for the Qualcomm SC7280
SoC, but this was based on a misunderstanding. There should only be
two interconnects defined: one between the IPA and system memory;
and another between the AP and IPA config space. The bandwidths
defined for the memory and config interconnects do not match what I
understand to be proper values, so update these.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge more updates from Andrew Morton:
"190 patches.
Subsystems affected by this patch series: mm (hugetlb, userfaultfd,
vmscan, kconfig, proc, z3fold, zbud, ras, mempolicy, memblock,
migration, thp, nommu, kconfig, madvise, memory-hotplug, zswap,
zsmalloc, zram, cleanups, kfence, and hmm), procfs, sysctl, misc,
core-kernel, lib, lz4, checkpatch, init, kprobes, nilfs2, hfs,
signals, exec, kcov, selftests, compress/decompress, and ipc"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
ipc/util.c: use binary search for max_idx
ipc/sem.c: use READ_ONCE()/WRITE_ONCE() for use_global_lock
ipc: use kmalloc for msg_queue and shmid_kernel
ipc sem: use kvmalloc for sem_undo allocation
lib/decompressors: remove set but not used variabled 'level'
selftests/vm/pkeys: exercise x86 XSAVE init state
selftests/vm/pkeys: refill shadow register after implicit kernel write
selftests/vm/pkeys: handle negative sys_pkey_alloc() return code
selftests/vm/pkeys: fix alloc_random_pkey() to make it really, really random
kcov: add __no_sanitize_coverage to fix noinstr for all architectures
exec: remove checks in __register_bimfmt()
x86: signal: don't do sas_ss_reset() until we are certain that sigframe won't be abandoned
hfsplus: report create_date to kstat.btime
hfsplus: remove unnecessary oom message
nilfs2: remove redundant continue statement in a while-loop
kprobes: remove duplicated strong free_insn_page in x86 and s390
init: print out unknown kernel parameters
checkpatch: do not complain about positive return values starting with EPOLL
checkpatch: improve the indented label test
checkpatch: scripts/spdxcheck.py now requires python3
...
kernel.h is being used as a dump for all kinds of stuff for a long time.
Here is the attempt to start cleaning it up by splitting out panic and
oops helpers.
There are several purposes of doing this:
- dropping dependency in bug.h
- dropping a loop by moving out panic_notifier.h
- unload kernel.h from something which has its own domain
At the same time convert users tree-wide to use new headers, although for
the time being include new header back to kernel.h to avoid twisted
indirected includes for existing users.
[akpm@linux-foundation.org: thread_info.h needs limits.h]
[andriy.shevchenko@linux.intel.com: ia64 fix]
Link: https://lkml.kernel.org/r/20210520130557.55277-1-andriy.shevchenko@linux.intel.com
Link: https://lkml.kernel.org/r/20210511074137.33666-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prior to IPA v3.5.1, there is no HW_PARAM_2 GSI register, which we
use to determine the number of channels and endpoints per execution
environment. In that case, we will just assume the number supported
is the maximum supported by the driver.
Introduce gsi_ring_setup() to encapsulate the code that determines
the number of channels and endpoints.
Update GSI_EVT_RING_COUNT_MAX so it is big enough to handle any
available channel for all supported hardware (IPA v4.9 can have 23
channels and 24 event rings).
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLAVOR_0 version first appears in IPA v3.5, so avoid attempting
to read it for versions prior to that.
This register contains a concise definition of the number and
direction of endpoints supported by the hardware, and without it
we can't verify endpoint configuration in ipa_endpoint_config().
In this case, just indicate that any endpoint number is available
for use.
Originally proposed by AngeloGioacchino Del Regno.
Link: https://lore.kernel.org/netdev/20210211175015.200772-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: David S. Miller <davem@davemloft.net>
For IPA v3.1, a workaround is needed to disable gating on a MISC
clock. I have no further explanation, but this is what the
downstream code (msm-4.4) does.
This was suggested in a patch from AngeloGioacchino Del Regno.
Link: https://lore.kernel.org/netdev/20210211175015.200772-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI inter-EE interrupts are not supported prior to IPA v3.5.
Don't attempt to initialize them in gsi_irq_setup() for hardware
that does not support them.
Originally proposed by AngeloGioacchino Del Regno.
Link: https://lore.kernel.org/netdev/20210211175015.200772-4-angelogioacchino.delregno@somainline.org
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: David S. Miller <davem@davemloft.net>
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function. of_node_put() on it before exiting
this function.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPA device attributes to expose information known by the IPA
driver about the hardware and its configuration.
All pointers used to display these attribute values (i.e., IPA
pointer and endpoint pointers) will have been initialized by the
time IPA probe has completed, so they may be safely dereferenced.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define and use a new function that just validates the version
defined in configuration data.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cost of validating the endpoint configuration data is not all
that high, so just do it unconditionally, rather than doing so only
when IPA_VALIDATAION is defined.
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally the code handles the IPA memory region array in the
configuration data without assuming it is indexed by region ID.
Get rid of the array index designators where these arrays are
initialized. As a result, there's no more need to define an
explicitly undefined memory region ID, so get rid of that.
Change ipa_mem_find() so it no longer assumes the ipa->mem[] array
is indexed by memory region ID. Instead, have it search the array
for the entry having the requested memory ID, and return the address
of the descriptor if found. Otherwise return NULL.
Stop allowing memory regions to be defined with zero size and zero
canary value. Check for this condition in ipa_mem_valid_one().
As a result, it is not necessary to check for this case in
ipa_mem_config().
Finally, there is no need for IPA_MEM_UNDEFINED to be defined any
more, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new function that abstracts finding information about a
region in IPA-local memory, given its memory region ID. For now it
simply uses the region ID as an index into the IPA memory array.
If the region is not defined, ipa_mem_find() returns a null pointer.
Update all code that accesses the ipa->mem[] array directly to use
ipa_mem_find() instead. The return value must be checked for null
when optional memory regions are sought.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop passing most of the Boolean flags to ipa_table_valid_one(), and
just pass a memory region ID to it instead. We still need to
indicate whether we're operating on a routing or filter table.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a memory region ID rather than the address of a memory region
descriptor to ipa_table_reset_add() to simplify callers. Similarly,
pass memory region IDs to ipa_table_init_add().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a memory region ID rather than the address of a memory region
descriptor to ipa_mem_zero_region_add() to simplify callers.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a memory region ID rather than the address of a memory region
descriptor to ipa_filter_reset_table(), to simplify callers.
We can eliminate the check for a zero region size in this function
because ipa_table_reset_add() checks that before adding anything to
the transaction.
Note that here and in subsequent commits there is no need to check
whether a memory region exists, because we will have already
verified that during initialization.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do some general cleanup in ipa_cmd_header_valid():
- Delay assigning the mem variable until just before it's used.
- Assign the maximum offset and size values together.
- Improve comments explaining the single range of memory being
made up of a modem portion and an AP portion.
- Record the offset of the combined range in a local variable.
- Do the initial size assignment right after assigning the offset.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ipa_mem_valid() to iterate over the entries using a u32 index
variable rather than using a memory region ID. Use the ID found
inside the memory descriptor rather than the loop index.
Change ipa_mem_size_valid() to iterate over the entries but without
assuming the array index is the memory region ID. "Empty" entries
will have zero size; and we'll temporarily assume such entries have
zero offset as well (they all do, currently).
Similarly, don't assume the mem[] array is indexed by ID in
ipa_mem_config(). There, "empty" entries will have a zero canary
count, so no special assumptions are needed to handle them correctly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform_get_irq() prints error message telling that interrupt is
missing,hence there is no need to duplicated that message in the
drivers.
Signed-off-by: Tan Zhongjun <tanzhongjun@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_mem_valid(), wait until regions have been marked in the memory
region bitmap, and check all that are not found there to ensure they
are not required.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test in ipa_mem_valid() to ensure no memory region is defined
more than once, using a bitmap to record each defined memory region.
Skip over undefined regions when checking (we can have any number of
those).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce ipa_mem_id_valid(), and use it to check defined memory
regions to ensure they are valid for a given version of IPA.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new function that indicates whether a given memory
region is required for a given version of IPA hardware. Use it to
verify that all required regions are present during initialization.
Reorder the definitions of the memory region IDs to be based on
the version in which they're first defined. Use "+" rather than
"and above" where defining the IPA versions in which memory IDs are
used, and indicate which regions are optional (many are not).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the memory configuration data array to ipa_mem_valid() for
validation, and use that rather than assuming it's already been
recorded in the IPA structure. Move the memory data array size
check into ipa_mem_valid().
Call ipa_mem_valid() early in ipa_mem_init(), and only proceed with
assigning the memory array pointer and size if it is found to be
valid.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the memory region validation check so it happens earlier when
initializing the driver, at init time rather than config time (i.e.,
before access to hardware is required).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only thing done by ipa_mem_valid_one() that requires hardware
access is the check for whether all regions fit within the size of
IPA local memory specified by an IPA register.
Introduce ipa_mem_size_valid() to implement this verification and
stop doing so in ipa_mem_valid_one(). Call the new function from
ipa_mem_config() (which is also the caller of ipa_mem_valid()).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, memory regions are validated in the loop that initializes
them. Instead, validate them separately.
Rename ipa_mem_valid() to be ipa_mem_valid_one(). Define a *new*
function named ipa_mem_valid() that performs validation of the array
of memory regions provided. This function calls ipa_mem_valid_one()
for each region in turn.
Skip validation for any "empty" region descriptors, which have zero
size and are not preceded by any canary values. Issue a warning for
such descriptors if the offset is non-zero.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do memory region descriptor validation unconditionally, rather than
having it depend on IPA_VALIDATION being defined.
Pass the address of a memory region descriptor rather than a memory
ID to ipa_mem_valid().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the memory region ID in the memory descriptor structure. This
is a move toward *not* indexing the array by the ID, but for now we
must still specify those index values. Define an explicitly
undefined region ID, value 0, so uninitialized entries in the array
won't use an otherwise valid ID.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new pseudo memory region identifer that specifies the
offset at the end of IPA resident memory. Use it instead of
IPA_MEM_UC_EVENT_RING in places where the size of that region was
defined to be 0.
The size of the IPA_MEM_END_MARKER pseudo region must be zero.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c88c34fcf8.
The RMNet driver now supports inline checksum offload.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with IPA v4.5, IP payload checksum offload is implemented
differently.
Prior to v4.5, the IPA hardware appends an rmnet_map_dl_csum_trailer
structure to each packet if checksum offload is enabled in the
download direction (modem->AP). In the upload direction (AP->modem)
a rmnet_map_ul_csum_header structure is prepended before each sent
packet.
Starting with IPA v4.5, checksum offload is implemented using a
single new rmnet_map_v5_csum_header structure which sits between
the QMAP header and the packet data. The same header structure
is used in both directions.
The new header contains a header type (CSUM_OFFLOAD); a checksum
flag; and a flag indicating whether any other headers follow this
one. The checksum flag indicates whether the hardware should
compute (and insert) the checksum on a sent packet. On a received
packet the checksum flag indicates whether the hardware confirms the
checksum value in the payload is correct.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA configuration data includes an array of memory region
descriptors. That was a fixed-size array at one time, but
at some point we started defining it such that it was only
as big as required for a given platform. The actual number
of entries in the array is recorded in the configuration data
along with the array.
A loop in ipa_mem_config() still assumes the array has entries
for all defined memory region IDs. As a result, this loop can
go past the end of the actual array and attempt to write
"canary" values based on nonsensical data.
Fix this, by stashing the number of entries in the array, and
using that rather than IPA_MEM_COUNT in the initialization loop
found in ipa_mem_config().
The only remaining use of IPA_MEM_COUNT is in a validation check
to ensure configuration data doesn't have too many entries.
That's fine for now.
Fixes: 3128aae8c4 ("net: ipa: redefine struct ipa_mem_data")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In gsi_irq_setup(), two registers are written with the intention of
disabling inter-EE channel and event IRQs.
But the wrong registers are used (and defined); the ones used are
read-only registers that indicate whether the interrupt condition is
present.
Define the mask registers instead of the status registers, and use
them to disable the inter-EE interrupt types.
Fixes: 46f748ccaf ("net: ipa: explicitly disallow inter-EE interrupts")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210505223636.232527-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA initialization includes loading some firmware. This step is
done either by the modem or by the AP under Trust Zone. If the
AP loads firmware, the name of the firmware file is currently
hard-coded ("ipa_fws.mdt").
Add the ability to specify the relative path of the firmware file to
use in a property in the Device Tree IPA node. If the property is
not found (or if any other error occurs attempting to get it), fall
back to using a default relative path.
Use the "old" fixed name as the default. Rename the symbol that
represents this default to emphasize its purpose.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SM8350 SoC, which includes IPA version 4.9.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SC7280 SoC, which includes IPA version 4.11.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SDX55 SoC, which includes IPA version 4.5.
Starting with IPA v4.5, a few of the memory regions have a different
number of "canary" values; update comments in the where the region
identifers are defined to accurately reflect that.
I'll note three differences in SDX55 versus the other two existing
platforms (SDM845 and SC7180):
- SDX55 uses a 32-bit Linux kernel
- SDX55 has four interconnects rather than three
- SDX55 uses IPA v4.5, which uses inline checksum offload
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checksum offload for IPA v4.5+ is implemented differently, using
"inline" offload (which uses a common header format for both upload
and download offload).
The IPA hardware must be programmed to enable MAP checksum offload,
but the RMNet driver is responsible for interpreting checksum
metadata supplied with messages.
Currently, the RMNet driver does not support inline checksum offload.
This support is imminent, but until it is available, do not allow
newer versions of IPA to specify checksum offload for endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago changes were made to stop referring to clearing the
hardware pipeline as a "tag process." Fix a comment to use the
newer terminology.
Get rid of a pointless double-negation of the Boolean toward_ipa
flag in ipa_endpoint_config().
make ipa_endpoint_exit_one() private; it's only referenced inside
"ipa_endpoint.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are place holder functions in the GSI code that do nothing.
Remove these, knowing we can add something back in their place if
they're really needed someday.
Some of these are inverse functions (such as teardown to match setup).
Explicitly comment that there is no inverse in these cases.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are place holder functions in the IPA code that do nothing.
For the most part these are inverse functions, for example, once the
routing or filter tables are set up there is no need to perform any
matching teardown activity at shutdown, or in the case of an error.
These can be safely removed, resulting in some code simplification.
Add comments in these spots making it explicit that there is no
inverse.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_modem_stop(), if the modem netdev pointer is non-null we call
ipa_stop(). We check for an error and if one is returned we handle
it. But ipa_stop() never returns an error, so this extra handling
is unnecessary. Simplify the code in ipa_modem_stop() based on the
knowledge no error handling is needed at this spot.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_modem_start(), we set endpoint netdev pointers before the
network device is registered. If registration fails, we don't undo
those assignments. Instead, wait to assign the netdev pointer until
after registration succeeds.
Set these endpoint netdev pointers to NULL in ipa_modem_stop()
before unregistering the network device.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On IPA v3.5.1, the sequencer type for the modem TX endpoint does not
define the replication portion in the same way the downstream code
does. This difference doesn't affect the behavior of the upstream
code, but I'd prefer the two code bases use the same configuration
value here.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I no longer know why a validation check ensured the size of an entry
passed to gsi_trans_pool_init() was restricted to be a multiple of 8.
For 32-bit builds, this condition doesn't always hold, and for DMA
pools, the size is rounded up to a power of 2 anyway.
Remove this restriction.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove repeated words "that" and "the".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Entries in an IPA route or filter table are 64-bit little-endian
addresses, each of which refers to a routing or filtering rule.
The format of these table slots are fixed, but IPA_TABLE_ENTRY_SIZE
is used to define their size. This symbol doesn't really add value,
and I think it unnecessarily obscures what a table entry *is*.
So get rid of IPA_TABLE_ENTRY_SIZE, and just use sizeof(__le64) in
its place throughout the code.
Update the comments in "ipa_table.c" to provide a little better
explanation of these table slots.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch avoided doing 64-bit modulo operations by checking
the alignment of some DMA allocations using only the lower 32 bits
of the address.
David Laight pointed out (after the fix was committed) that DMA
allocations might already satisfy the alignment requirements. And
he was right.
Remove the alignment checks that occur after DMA allocation requests,
and update comments to explain why the constraint is satisfied. The
only place IPA_TABLE_ALIGN was used was to check the alignment; it is
therefore no longer needed, so get rid of it.
Add comments where GSI_RING_ELEMENT_SIZE and the tre_count and
event_count channel data fields are defined to make explicit they
are required to be powers of 2.
Revise a comment in gsi_trans_pool_init_dma(), taking into account
that dma_alloc_coherent() guarantees its result is aligned to a page
size (or order thereof).
Don't bother printing an error if a DMA allocation fails.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the SC7180 configuration data file so that its name is
derived from its IPA version.
Update a few other references to the code that talk about the SC7180
rather than just IPA v4.2.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the SDM845 configuration data file so that its name is
derived from its IPA version. I am not aware of any special IPA
behavior or handling that would be based on a specific SoC (as
opposed to a specific version of the IPA it contains).
Update a few other references to the code that talk about the SDM845
rather than just IPA v3.5.1.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't typically need much information about modem endpoints.
Normally we need to specify information about modem endpoints in
configuration data in only two cases:
- When a modem TX endpoint supports filtering
- When another endpoint's configuration refers to it
For the first case, the AP initializes the filter table, and must
know how many endpoints (AP and modem) support filtering. An
example of the second case is the AP->modem TX endpoint, which
defines the modem<-AP RX endpoint as its status endpoint.
There is one exception to this, and it's due to a hardware quirk.
For IPA v4.2 (only) there is a problem related to allocating GSI
channels. And to work around this, the AP allocates *all* GSI
channels at startup time--including those used by the modem.
Get rid of the configuration information for two endpoints not
required for the SDM845. SC7180 runs IPA v4.2, so we can't
eliminate any modem endpoint definitions there.
Two more minor changes:
- Reorder the members defined for the ipa_endpoint_name enumerated
type to match the order used in configuration data files when
defining endpoints.
- Add a new name, IPA_ENDPOINT_MODEM_DL_NLO_TX, which can be used
for IPA v4.5+.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The backward compatibility register value is a platform-specific
property that is not stored in the platform data. Create a data
field where this can be represented, and get rid ipa_reg_bcr_val().
This register is not present starting with IPA v4.5.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix all warnings produced when running:
scripts/kernel-doc -none drivers/net/ipa/*.[ch]
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA versions 3.0 and 3.1 support up to 8 resource groups. There is
some interest in supporting these older versions of the hardware, so
update the resource configuration code to program resource limits
for these groups if specified.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arrays of source and destination resource limits defined in
configuration data are of a fixed size--which is the maximum number
of resource groups supported for any platform. Most platforms will
use fewer than that many groups.
Add new members to the ipa_rsrc_group_id enumerated type to define
the number of source and destination resource groups are defined for
the platform. (This type is defined for each platform in its data
file.)
Add a new field to the resource configuration data that indicates
how many of the source and destination resource groups are actually
used for the platform, and initialize it with the count value. This
allows us to determine the number of groups defined for the platform
without exposing the ipa_rsrc_group_id enumerated type.
As a result, we no longer need ipa_resource_group_src_count()
and ipa_resource_group_dst_count(), because each platform now
defines its supported number of resource groups. So get rid of
those two functions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the resource data pointer to ipa_resource_config_src() and
ipa_resource_config_dst() to be used for configuring resource
limits.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipa_resource_src and ipa_resource_dst structures are identical
in form, so just replace them with a single structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace IPA_RESOURCE_GROUP_SRC_MAX and IPA_RESOURCE_GROUP_DST_MAX
with a single symbol, IPA_RESOURCE_GROUP_MAX.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most platforms have the same set of source and destination resource
types. But some older platforms have some additional ones, and it's
possible different resources will be used in the future.
Move the definition of the ipa_resource_type enumerated type so it
is defined for each platform in its configuration data file. This
permits each to have a distinct set of resources.
Shorten the data files slightly, by putting the min and max limit
values on the same line.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the type field from the ipa_resource_src and ipa_resource_dst
structures, and instead use that value as the index into the arrays
of source and destination resources.
Change ipa_resource_config_src() and ipa_resource_config_dst() so
the resource type is passed in as an argument.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine the ipa_resource_type_src and ipa_resource_type_dst
enumerated types into a single enumerated type, ipa_resource_type.
Assign value 0 to the first element for the source and destination
types, so their numeric values are preserved. Add some additional
commentary where these are defined, stating explicitly that code
assumes the first source and first destination member must have
numeric value 0.
Fix the kerneldoc comments for the ipa_gsi_endpoint_data structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the SDM845 configuration data defines resource limits for
the first two resource groups (for both source and destination
resource types). The hardware supports additional resource groups,
and we should program the resource limits for those groups as well.
Even the "unused" destination resource group (number 2) should have
non-zero limits programmed in some cases, to ensure correct operation.
Add these missing resource group limit definitions to the SDM845
configuration data.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new ipa_resource_group_id enumerated type, whose members
have numeric values that match the resource group number used when
programming the hardware. Each platform supports a different number
of source and destination resource groups, so define the type
separately for each platform in its configuration data file.
Use these new symbolic values when specifying the resource group an
endpoint is associated with. And use them to index the limits
arrays for source and destination resources, making it clearer how
these values are used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the number of resource groups supported by the hardware is less
than a certain number, we return early in ipa_resource_config_src()
and ipa_resource_config_dst() (to avoid programming resource limits
for non-existent groups).
Unfortunately, these checks are off by one. Fix this problem in the
four places it occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the IPA resource-related code into a new source file,
"ipa_resource.c", and matching header file "ipa_resource.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA v4.5 (GSI v2.5) supports a larger set of channel protocols, and
adds an additional field to hold the most-significant bits of the
protocol identifier on a channel.
Add an inline function that encodes the protocol (including the
extra bits for newer versions of IPA), and define some additional
protocols. At this point we still use only GPI protocol.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each GSI channel has a CNTXT_1 register that encodes the size of its
ring buffer. The size of the field that records that is increased
starting at IPA v4.9. Replace the use of a fixed-size field mask
with a new inline function that encodes that size value.
Similarly, the size of GSI event rings can be larger starting with
IPA v4.9, so create a function to encode that as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main purpose of this is to extend these GSI register definitions
to support additional IPA versions.
This patch makes some minor updates to "gsi_reg.h":
- Define a DB_IN_BYTES field in the channel QOS register
- Add some comments clarifying when certain fields are valid
- Add the definition of GSI_CH_DB_STOP channel command
- Add a couple of blank lines
- Move one comment and indent another
- Delete two unused register definitions at the end.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with IPA v4.7, registers related to IPA interrupts are
located at a fixed offset 0x1000 above than the addresses used for
earlier versions. Define and use functions to provide the offset to
use for these registers based on IPA version.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA version 4.9 and later use a different layout of some fields
found in the COMP_CFG register.
Define arbitration_lock_disable_encoded(), and use it to encode a
value into the ATOMIC_FETCHER_ARB_LOCK_DIS field based on the IPA
version.
And define full_flush_rsc_closure_en_encoded() to encode a value
into the FULL_FLUSH_WAIT_RSC_CLOSE_EN field based on the IPA
version.
The values of these fields are neither modified nor extracted by
current code, but this patch makes this possible for all supported
versions.
Fix a mistaken comment above ipa_hardware_config_comp() intended to
describe the purpose for the register.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and update IPA register definitions. Extend these definitions
to incorporate a fairly small number of new symbols (register
offsets and fields) to support IPA v3.0, v3.1, v3.5, v4.0, v4.1,
v4.7, 4.9, and v4.11, and have the comments reflect when they are
valid. None of the added symbols require changes elsewhere in the
code.
Update rsrc_grp_encoded() to support these other IPA versions.
Add kerneldoc comments for the IPA IRQ numbers and sequencer type.
Fix a few spots where the version check should be less restrictive
(missed by an earlier patch).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the maximum number of channels and event rings supported by
the driver, to allow the maximum available on the SDX55.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only use ipa_aggr_granularity_val() inside "ipa_main.c", so it
doesn't really need to be defined in a header file. It makes some
sense to be grouped with the register definitions, but it is unlike
the other inline functions now defined in "ipa_reg.h". So move it
into "ipa_main.c" where it's used. TIMER_FREQUENCY is used only
by that function, so move that definition as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all of the bits of the LOCAL_PKT_PROC_CNTXT register are valid.
Until IPA v4.5, there are 17 valid bits (though the bottom three
must be zero). Starting with IPA v4.5, 18 bits are valid.
Introduce proc_cntxt_base_addr_encoded() to encode the base address
for use in the register using only the valid bits.
Shorten the name of the register (omit "_BASE") to avoid the need to
wrap the line in the one place it's used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the ENDP_INIT_NAT register for setting up the NAT
configuration for an endpoint. We aren't using NAT at this
time, so explicitly set the type to BYPASS for all endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPA version definitions for all IPA v3.x and v4.x. Fix the GSI
version associated with IPA version 4.1.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify conditional tests throughout the IPA code so they do not
assume that IPA v3.5.1 is the oldest version supported. Also remove
assumptions that IPA v4.5 is the newest version of IPA supported.
Augment versions in comments with "+", to be clearer that the
comment applies to a version and subsequent versions. (E.g.,
"present for IPA v4.2+" instead of just "present for v4.2".)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a 32 bit x86 build to use a 64 bit DMA address.
There are two remaining spots where the IPA driver does a modulo
operation to check alignment of a DMA address, and under certain
conditions this can lead to a build error on i386 (at least).
The alignment checks we're doing are for power-of-2 values, and this
means the lower 32 bits of the DMA address can be used. This ensures
both operands to the modulo operator are 32 bits wide.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
We only program the sequencer type for TX endpoints. So move the
definition of the sequencer type fields into the TX-specific portion
of the endpoint configuration data. There's no need to maintain
this in the IPA structure; we can extract it from the configuration
data it points to in the one spot it's needed.
We previously specified the sequencer type for RX endpoints with
INVALID values. These are no longer needed, so get rid of them.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IPA endpoint has a sequencer that must be configured based on how
the endpoint is to be used. Currently the IPA code programs the
sequencer type by splitting a value into four 4-bit nibbles. Doing
that doesn't really add much value, and regardless, a better way of
splitting the sequencer type is into two halves--the lower byte
describing how normal packet processing is handled, and the next
byte describing information about processing replicas.
So split the sequencer type into two sub-parts: the sequencer type
and the replication sequencer type. Define the values supported for
the "main" sequencer type, and define the values supported for the
replication part separately.
In addition, the sequencer type names are quite verbose, encoding
what the type includes, but also what it *excludes*. Rename the
sequencer types in a way that mainly describes the number of passes
that a packet takes through the IPA processing pipeline, and how
many of those passes end by supplying the processed packet to the
microprocessor.
The result expands the supported types beyond what is required for
now, but simplifies the way these are defined.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with IPA v4.0, a limit is placed on the number of bytes
outstanding in a transaction, to reduce latency. The limit is
imposed only if this value is non-zero.
We don't use a non-zero value for SC7180, but newer versions of IPA
do. Prepare for that by allowing a programmed value to be specified
in the platform configuration data.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the QSB configuration data in ipa_hardware_config_qsb(), rather
than determining in code what values to use based on IPA version.
Pass configuration data to ipa_hardware_config() so it can be passed
to ipa_hardware_config_qsb().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use ipa_cmd_header_valid() to ensure certain values we will
program into hardware are within range, well in advance of when we
actually program them. This way we avoid having to check for errors
when we actually program the hardware.
Unfortunately the dev_err() call for a bad offset value does not
supply the arguments to match the format specifiers properly.
Fix this.
There was also supposed to be a check to ensure the size to be
programmed fits in the field that holds it. Add this missing check.
Rearrange the way we ensure the header table fits in overall IPA
memory range.
Finally, update ipa_cmd_table_valid() so the format of messages
printed for errors matches what's done in ipa_cmd_header_valid().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the maximum number of reads and writes to configure for the
QSB masters used for IPA in configuration data.
We don't use these values yet; the next commit takes care of that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several memory regions that are defined starting with IPA
v4.0, but which were not used for the SC7180 SoC (IPA v4.2). Even
though they're not used (yet), define them so they are ready to be
used for SoCs when they become supported.
There are two QUOTA statistics memory regions, one for the modem and
one for the AP. Define distinct names for these regions, and get
rid of the definition of IPA_MEM_STATS_QUOTA.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AP_HEADER memory region for both the SDM845 and SC7180 SoCs has
zero size, and has no canaries. Defining an offset for such a
zero-length region is not meaningful, so it's better not to define
it at all. The size of this region is used in the code, but its
value will still be zero because the memory regions are defined in
statically initialized memory.
For the SC7180, the STATS_DROP memory region has a zero size and no
canaries as well.
These regions are the only place where a zero-sized region is
defined despite having no canaries. Remove them.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There should be no canary values written before the beginning of the
UC_INFO memory region. This was correct for SDM845, but somehow was
committed with the wrong value for SC7180.
This bug seems to cause no harm, so we'll just correct it without
back-porting.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the platform configuration data should be constant, but
that isn't the case for the memory regions, interconnects, and
clocks. Fix this.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently assume the IPA driver is built only for a 64 bit kernel.
When this constraint was put in place it eliminated some do_div()
calls, replacing them with the "/" and "%" operators. We now only
use these operations on u32 and size_t objects. In a 32-bit kernel
build, size_t will be 32 bits wide, so there remains no reason to
use do_div() for divide and modulo.
A few recent commits also fix some code that assumes that DMA
addresses are 64 bits wide.
With that, we can get rid of the 64-bit build requirement.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have a build-time check to ensure that the minimum DMA
allocation alignment satisfies the constraint that IPA filter and
route tables must point to rules that are 128-byte aligned.
But what's really important is that the actual allocated DMA memory
has that alignment, even if the minimum is smaller than that.
Remove the BUILD_BUG_ON() call checking against minimim DMA alignment
and instead verify at rutime that the allocated memory is properly
aligned.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use upper_32_bits() to extract the high-order 32 bits of a DMA
address. This avoids doing a 32-position shift on a DMA address
if it happens not to be 64 bits wide. Use lower_32_bits() to
extract the low-order 32 bits (because that's what it's for).
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some build time checks in ipa_table_validate_build() assume that a
DMA address is 64 bits wide. That is more restrictive than it has
to be. A route or filter table is 64 bits wide no matter what the
size of a DMA address is on the AP. The code actually uses a
pointer to __le64 to access table entries, and a fixed constant
IPA_TABLE_ENTRY_SIZE to describe the size of those entries.
Loosen up two checks so they still verify some requirements, but
such that they do not assume the size of a DMA address is 64 bits.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck report:
drivers/net/ipa/gsi.c:1341:2-9:
line 1341 is redundant because platform_get_irq() already prints an error
Remove dev_err() messages after platform_get_irq_byname() failures.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The specified format of the INDICATION_REGISTER QMI request message
has been extended to support two more optional fields:
endpoint_desc_ind:
sender wishes to receive endpoint descriptor information via
an IPA ENDP_DESC indication QMI message
bw_change_ind:
sender wishes to receive bandwidth change information via
an IPA BW_CHANGE indication QMI message
Add definitions that permit these fields to be formatted and parsed
by the QMI library code.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipa_init_modem_driver_req_ei[] encoding array for the
INIT_MODEM_DRIVER request message has some errors in it.
First, the tlv_type associated with the hw_stats_quota_size field is
wrong; it duplicates the valiue used for the hw_stats_quota_base_addr
field (0x1f) and should use 0x20 instead. The tlv_type value for
the hw_stats_drop_size field also uses the same duplicate value; it
should use 0x22 instead.
Second, there is no definition for the hw_stats_drop_base_addr
field. It is an optional 32-bit enumerated type value.
Finally, the hw_stats_quota_base_addr, hw_stats_quota_size, and
hw_stats_drop_size fields are defined as enumerated types; they
should be unsigned 4-byte values.
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ipa_indication_register_req_ei[] encoding array, the tlv_type
associated with the ipa_mhi_ready_ind field is wrong. It duplicates
the value used for the data_usage_quota_reached field (0x11) and
should use value 0x12 instead. Fix this bug.
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In review, Alexander Duyck suggested that ipa_table_hash_support()
was trivial enough that it could be implemented as a static inline
function in the header file. But the patch had already been
accepted. Implement his suggestion.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a QMI handle is initialized, an array of message handler
structures is provided, defining how any received message should
be handled based on its type and message ID. The QMI core code
traverses this array when a message arrives and calls the function
associated with the (type, msg_id) found in the array.
The array is supposed to be terminated with an empty (all zero)
entry though. Without it, an unsupported message will cause
the QMI core code to go past the end of the array.
Fix this bug, by properly terminating the message handler arrays
provided when QMI handles are set up by the IPA driver.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Reported-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We configure the minimum and maximum number of various types of IPA
resources in ipa_resource_config(). It iterates over resource types
in the configuration data and assigns resource limits to each
resource group for each type.
Unfortunately, we are repeatedly initializing the resource data for
the first type, rather than initializing each of the types whose
limits are specified.
Fix this bug.
Fixes: 4a0d7579d4 ("net: ipa: avoid going past end of resource group array")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a simple helper function that indicates whether a channel has
been initialized. This abstacts/hides the details of how this is
determined.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new function to abstract the knowledge of whether hashed
routing and filter tables are supported for a given IPA instance.
IPA v4.2 is the only one that doesn't support hashed tables (now
and for the foreseeable future), but the name of the helper function
is better for explaining what's going on.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_cmd_register_write_valid() we verify that values we will
supply to a REGISTER_WRITE IPA immediate command will fit in
the fields that need to hold them. This patch fixes some issues
in that function and ipa_cmd_register_write_offset_valid().
The dev_err() call in ipa_cmd_register_write_offset_valid() has
some printf format errors:
- The name of the register (corresponding to the string format
specifier) was not supplied.
- The IPA base offset and offset need to be supplied separately to
match the other format specifiers.
Also make the ~0 constant used there to compute the maximum
supported offset value explicitly unsigned.
There are two other issues in ipa_cmd_register_write_valid():
- There's no need to check the hash flush register for platforms
(like IPA v4.2) that do not support hashed tables
- The highest possible endpoint number, whose status register
offset is computed, is COUNT - 1, not COUNT.
Fix these problems, and add some additional commentary.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the IPA core clock and interconnects, it's
possible we'll get an EPROBE_DEFER error. This isn't really an
error, it's just means we need to be re-probed later.
Use dev_err_probe() to report the error rather than dev_err().
This avoids polluting the log with these "error" messages.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch actually fixes a bug, though it doesn't affect the two
platforms supported currently. The fix implements GSI memory
pointers a bit differently.
For IPA version 4.5 and above, the address space for almost all GSI
registers is adjusted downward by a fixed amount. This is currently
handled by adjusting the I/O virtual address pointer after it has
been mapped. The bug is that the pointer is not "de-adjusted" as it
should be when it's unmapped.
This patch fixes that error, but it does so by maintaining one "raw"
pointer for the mapped memory range. This is assigned when the
memory is mapped and used to unmap the memory. This pointer is also
used to access the two registers that do *not* sit in the "adjusted"
memory space.
Rather than adjusting *that* pointer, we maintain a separate pointer
that's an adjusted copy of the "raw" pointer, and that is used for
most GSI register accesses.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that the length passed to ipa_header_size_encoded()
is larger than what can be represented by the HDR_LEN field alone
(starting with IPA v4.5). If we attempted that, u32_encode_bits()
would trigger a build-time error.
Avoid this problem by masking off high-order bits of the value
encoded as the lower portion of the header length.
The same sort of problem exists in ipa_metadata_offset_encoded(),
so implement the same fix there.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a build-time check that the packet status structure is a
multiple of 4 bytes in size. It's not clear where that constraint
comes from, but the structure defines what hardware provides so its
definition won't change. Get rid of the check; it adds no value.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The count argument to ipa_endpoint_replenish() is only ever 0 or 1,
and always will be (because we always handle each receive buffer in
a single transaction). Rename the argument to be add_one and change
it to be Boolean.
Update the function description to reflect the current code.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We do not support inter-EE channel or event ring commands. Inter-EE
interrupts are disabled (and never re-enabled) for all channels and
event rings, so we have no need for the GSI registers that clear
those interrupt conditions. So remove their definitions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An event ring's state only needs to be known when it is allocated,
reset, or deallocated. We check an event ring's state both before
and after performing an event ring control command that changes
its state. These are only issued at startup and shutdown, so there
is very little value in caching the state.
Stop recording a copy of the channel's last known state, and instead
fetch the true state from hardware whenever it's needed. In such
cases, *do* record the state in a local variable, in case an error
message reports it (so the value reported is the value seen).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When stopping a channel, gsi_channel_stop() will ensure NAPI
polling is complete when it calls napi_disable(). So there is no
need to call napi_synchronize() in that case.
Move the call to napi_synchronize() out of __gsi_channel_stop()
and into gsi_channel_suspend(), so it's only used where needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the mutex calls out of gsi_channel_stop_retry() and into
__gsi_channel_stop(), to make the latter more semantically similar
to __gsi_channel_start().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In gsi_channel_setup(), we check to see if the configuration data
contains any information about channels that are not supported by
the hardware. If one is found, we abort the setup process, but
the error code (ret) is not set in this case. Fix this bug.
Fixes: 650d160382 ("soc: qcom: ipa: the generic software interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210204010655.15619-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Transactions to send data for a network device can be allocated at
any time up until the point the TX queue is stopped. It is possible
for ipa_start_xmit() to be called in one context just before a
the transmit queue is stopped in another.
Update gsi_channel_trans_last() so that for TX channels the
allocated and pending transaction lists are checked--in addition
to the completed and polled lists--to determine the "last"
transaction. This means any transaction that has been allocated
before the TX queue is stopped will be allowed to complete before
we conclude the channel is quiesced.
Rework the function a bit to use a list pointer and gotos.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No completion interrupts will occur while an endpoint is suspended,
nor when a channel has been stopped for suspend. So there's no need
to disable the interrupt during suspend and re-enable it when
resuming. Without any interrupts occurring, there is no need to
disable/re-enable NAPI for channel suspend/resume either.
We'll only enable NAPI and the interrupt when we first start the
channel, and disable it again only when it's "really" stopped.
To accomplish this, move the enable/disable calls out of
__gsi_channel_start() and __gsi_channel_stop(), and into
gsi_channel_start() and gsi_channel_stop() instead.
Add a call to napi_synchronize() to gsi_channel_suspend(), to ensure
NAPI polling is done before moving on.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Disable both the I/O completion interrupt and NAPI polling on a
channel *after* we successfully stop it rather than before. This
ensures a completion occurring just before the channel is stopped
gets processed.
Enable NAPI polling and the interrupt *before* starting a channel
rather than after, to be symmetric. A stopped channel won't
generate any completion interrupts anyway.
Enable NAPI before the interrupt and disable it afterward.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Open-code gsi_channel_freeze() and gsi_channel_thaw() in all callers
and get rid of these two functions. This is part of reworking the
sequence of things done during channel suspend/resume and start/stop.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a new function that does most of the work of starting a
channel. What's different is that it takes a flag indicating
whether the channel should really be started or not. Create
another new function __gsi_channel_stop() that behaves similarly.
IPA v3.5.1 implements suspend using a special SUSPEND endpoint
setting. If the endpoint is suspended when an I/O completes on the
underlying GSI channel, a SUSPEND interrupt is generated.
Newer versions of IPA do not implement the SUSPEND endpoint mode.
Instead, endpoint suspend is implemented by simply stopping the
underlying GSI channel. In this case, a completing I/O on a
*stopped* channel causes the SUSPEND interrupt condition.
These new functions put all activity related to starting or stopping
a channel (including "thawing/freezing" the channel) in one place,
whether or not the channel is actually started or stopped.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a new helper function that encapsulates issuing a set of
channel stop commands, retrying if appropriate, with a short delay
between attempts.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If an error occurs starting a channel, don't "thaw" it.
We should assume the channel remains in a non-started state.
Update the comment in gsi_channel_stop(); calls to this function
are no longer retried.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix two format specifiers that used %lu for a size_t in "ipa_mem.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When extracting the destination endpoint ID from the status in
ipa_endpoint_status_skip(), u32_get_bits() is used. This happens to
work, but it's wrong: the structure field is only 8 bits wide
instead of 32.
Fix this by using u8_get_bits() to get the destination endpoint ID.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sparse warns that the assignment of the metadata mask for a QMAP
endpoint in ipa_endpoint_init_hdr_metadata_mask() is a bad
assignment. We know we want the mask value to be big endian, even
though the value we write is in host byte order. Use a __force
tag to indicate we really mean it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The virt local variable in gsi_channel_state() does not have an
__iomem attribute but should. Fix this.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Amy Parker <enbyamy@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "ring->addr = addr;" assignment is done a few lines later so we
can't use "ring->addr" yet. The correct dma_handle is "addr".
Fixes: 650d160382 ("soc: qcom: ipa: the generic software interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/YBjpTU2oejkNIULT@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only time we transfer data (rather than issuing a command) out
of the AP->command TX endpoint is when we're clearing the hardware
pipeline. All that's needed is a "small" data buffer, and its
contents aren't even important.
For convenience, we just transfer a command structure in this case
(it's already mapped for DMA). The TRE is added to a transaction
using ipa_cmd_ip_tag_status_add(), but we ignore the size value
provided to that function. So just get rid of the size argument.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We only send a tagged packet from the AP->command TX endpoint when
we're clearing the hardware pipeline. And when we receive the
tagged packet we don't care what the actual tag value is.
Stop passing a tag value to ipa_cmd_ip_tag_status_add(), and just
encode 0 as the tag sent. Fix the function that encodes the tag so
it uses the proper byte ordering.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are times, such as when the modem crashes, when we issue
commands to clear the IPA hardware pipeline. These commands include
a data transfer command that delivers a small packet directly to the
default (AP<-LAN RX) endpoint.
The places that do this wait for the transactions that contain these
commands to complete, but the pipeline can't be assumed clear until
the sent packet has been *received*.
The small transfer will be delivered with a status structure, and
that status will indicate its tag is valid. This is the only place
we send a tagged packet, so we use the tag to determine when the
pipeline clear packet has arrived.
Add a completion to the IPA structure to to be used to signal
the receipt of a pipeline clear packet. Create a new function
ipa_cmd_pipeline_clear_wait() that will wait for that completion.
Reinitialize the completion whenever pipeline clear commands are
added to a transaction. Extend ipa_endpoint_status_tag() to check
whether a packet whose status contains a valid tag was sent from the
AP->command TX endpoint, and if so, signal the new IPA completion.
Have all callers of ipa_cmd_pipeline_clear_add() wait for the
pipeline clear indication after the transaction that clears the
pipeline has completed.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce ipa_endpoint_status_tag(), which returns true if received
status indicates its tag field is valid. The endpoint parameter is
not yet used.
Call this from ipa_status_drop_packet(), and drop the packet if the
status indicates the tag was valid. Pass the endpoint pointer to
ipa_status_drop_packet(), and rename it ipa_endpoint_status_drop().
The endpoint will be used in the next patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rearrange some comments and assignments made when handling a packet
that is received with status, aiming to improve understandability.
Use DIV_ROUND_CLOSEST() to get a better per-packet true size estimate.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a set of functions and symbols related to performing
"tag_process" immediate commands to clear the IPA pipeline. The
name is related to one of the commands issued when doing this, but
it doesn't really convey the overall purpose of taking this action.
The purpose is to take some steps to "clear out" the hardware
pipeline, and to wait until that process completes, to ensure the
IPA hardware is in a well-defined state.
Rename these symbols to use "pipeline_clear" in their names instead.
Add some comments to explain a bit more about what's going on.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently in gsi_isr_ieob(), event ring IEOB interrupts are disabled
one at a time. The loop disables the IEOB interrupt for all event
rings represented in the event mask. Instead, just disable them all
at once.
Disable them all *before* clearing the interrupt condition. This
guarantees we'll schedule NAPI for each event once, before another
IEOB interrupt could be signaled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename gsi_irq_ieob_disable() to be gsi_irq_ieob_disable_one().
Introduce a new function gsi_irq_ieob_disable() that takes a mask of
events to disable rather than a single event id. This will be used
in the next patch.
Rename gsi_irq_ieob_enable() to be gsi_irq_ieob_enable_one() to be
consistent.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Have gsi_channel_update() return the first transaction in the
updated completed transaction list, or NULL if no new transactions
have been added.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pay attention to the return value of napi_complete(), completing
polling only if it returns true.
Just use napi rather than &channel->napi as the argument passed to
napi_complete().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an off-by-one problem in gsi_channel_poll(). The count of
transactions completed is incremented each time through the loop
*before* determining whether there is any more work to do. As a
result, if we exit the loop early the counter its value is one more
than the number of transactions actually processed.
Instead, increment the count after processing, to ensure it reflects
the number of processed transactions. The result is more naturally
described as a for loop rather than a while loop, so change that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA driver currently requires a DT property to be defined whose
value is the phandle for the modem subsystem. This was needed to
look up a remoteproc structure pointer used when registering for
notifications in the original IPA notification mechanism.
Remoteproc provides a more generic SSR notifier system, and the IPA
driver switched over to it last summer, but this remoteproc phandle
dependency was not removed at that time.
Get rid of the IPA remoteproc pointer and stop requiring the phandle
be specified.
This avoids a link error (rproc_put() not defined) for certain
configurations.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently we assume that the IPA hardware has exactly three
interconnects. But that won't be guaranteed for all platforms,
so allow any number of interconnects to be specified in the
configuration data.
For each platform, define an array of interconnect data entries
(still associated with the IPA clock structure), and record the
number of entries initialized in that array.
Loop over all entries in this array when initializing, enabling,
disabling, or tearing down the set of interconnects.
With this change we no longer need the ipa_interconnect_id
enumerated type, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass an the address of an IPA interconnect structure and its
configuration data to ipa_interconnect_init_one() and have that
function initialize all the structure's fields. Change the function
to simply return an error code.
Introduce ipa_interconnect_exit_one() to encapsulate the cleanup of
an IPA interconnect structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the name to the configuration data for each interconnect. Use
this information rather than a constant string during initialization.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add fields in the ipa_interconnect structure to hold the average and
peak bandwidth values for the interconnect. Pass the configuring
data for interconnects to ipa_interconnect_init() so these values
can be recorded, and use them when enabling the interconnects.
There's no longer any need to keep a copy of the interconnect data
after initialization.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than having separate pointers for the memory, imem, and
config interconnect paths, maintain an array of ipa_interconnect
structures each of which contains a pointer to a path.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If disabling interconnects fails there's not a lot we can do. The
only two callers of ipa_interconnect_disable() ignore the return
value, so just give the function a void return type.
Print an error message if disabling any of the interconnects is not
successful. Return (and print) only the first error seen.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use "bandwidth" rather than "rate" in describing the average and
peak values to use for IPA interconnects. They should have been
named that way to begin with.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For RX channels we issue a stop command more than once if necessary
to allow it to stop. It turns out that TX channels could also
require retries.
Retry channel stop commands if necessary regardless of the channel
direction. Rename the symbol defining the retry count so it's not
RX-specific.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a GSI stop channel command leaves the channel in STOP_IN_PROC
state, we retry the stop command after a 1-2 millisecond delay.
I have been told that a 3-5 millisecond delay is a better choice.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The GSI command timeout is currently 5 seconds, which is much higher
than it should be.
Express the timeout in milliseconds rather than seconds, and reduce
it to 50 milliseconds.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
65;6003;1c
The use of msleep() for small periods (less than 20 milliseconds) is
not recommended because the actual delay can be much different than
expected.
We use msleep(1) in several places in the IPA driver to insert short
delays. Replace them with usleep_range calls, which should reliably
delay a period in the range requested.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a new function gsi_irq_ev_ctrl_enable() that encapsulates
enabling the event ring control GSI interrupt type, and enables a
single event ring to signal that interrupt. When an event ring
changes state as a result of an event ring command, it triggers this
interrupt.
Create an inverse function gsi_irq_ev_ctrl_disable() as well.
Because only one event ring at a time is enabled for this interrupt,
we can simply disable the interrupt for *all* channels.
Create a pair of helpers that serve the same purpose for channel
commands.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return value of gsi_command() is true if successful or false if
we time out waiting for a completion interrupt.
Rename the variables in the three callers of gsi_command() to be
"timeout", to make it more obvious that's the only reason for
failure.
In addition, add a "gsi_" prefix to evt_ring_command() so its name
is consistent with the convention used for GSI channel and generic
commands.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA driver depends on some SMEM functionality (qcom_smem_init(),
qcom_smem_alloc(), and qcom_smem_virt_to_phys()), but this is not
reflected in the configuration dependencies. Add a dependency on
QCOM_SMEM to avoid attempts to build the IPA driver without SMEM.
This avoids a link error for certain configurations.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 38a4066f59 ("net: ipa: support COMPILE_TEST")
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210112192134.493-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arrange for the IPA driver to be built when COMPILE_TEST is enabled.
Update the help text to reflect that we support two Qualcomm SoCs.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The second argument to gsi_trans_page_add() is a page pointer.
That declaration is found in header files used by "gsi_trans.h" for
(at least) arm64 and x86 builds, but apparently not for alpha
builds.
Fix this by adding a declaration of struct page to the top of
"gsi_trans.h".
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At the moment it is quite hard to identify the network interface
provided by IPA in userspace components: The network interface is
created as virtual device, without any link to the IPA device.
The interface name ("rmnet_ipa%d") is the only indication that the
network interface belongs to IPA, but this is not very reliable.
Add SET_NETDEV_DEV() to associate the network interface with the
IPA parent device. This allows userspace services like ModemManager
to properly identify that this network interface is provided by IPA
and belongs to the modem.
Cc: Alex Elder <elder@kernel.org>
Fixes: a646d6ec90 ("soc: qcom: ipa: modem and microcontroller")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106100755.56800-1-stephan@gerhold.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Callers of evt_ring_command() no longer care whether the command
times out, and don't use what evt_ring_command() returns. Redefine
that function to have void return type.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 428b448ee7 ("net: ipa: use state to determine event ring command success")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Callers of gsi_channel_command() no longer care whether the command
times out, and don't use what gsi_channel_command() returns. Redefine
that function to have void return type.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 6ffddf3b3d ("net: ipa: use state to determine channel command success")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch implements the same basic fix for event rings as the
previous one does for channels.
The result of issuing an event ring control command should be that
the event ring changes state. If enabled, a completion interrupt
signals that the event ring state has changed. This interrupt is
enabled by gsi_evt_ring_command() and disabled again after the
command has completed (or we time out).
There is a window of time during which the command could complete
successfully without interrupting. This would cause the event ring
to transition to the desired new state.
So whether a event ring command ends via completion interrupt or
timeout, we can consider the command successful if the event ring
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes: b4175f8731 ("net: ipa: only enable GSI event control IRQs when needed")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The result of issuing a channel control command should be that the
channel changes state. If enabled, a completion interrupt signals
that the channel state has changed. This interrupt is enabled by
gsi_channel_command() and disabled again after the command has
completed (or we time out).
There is a window of time--after the completion interrupt is disabled
but before the channel state is read--during which the command could
complete successfully without interrupting. This would cause the
channel to transition to the desired new state.
So whether a channel command ends via completion interrupt or
timeout, we can consider the command successful if the channel
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes: d6c9e3f506 ("net: ipa: only enable generic command completion IRQ when needed");
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We enable the completion interrupt for channel or event ring
commands only when we issue them. The interrupt is disabled after
the interrupt has fired, or after we have timed out waiting for it.
If we time out, the command could complete after the interrupt has
been disabled, causing a state change in the channel or event ring.
The interrupt associated with that state change would be delivered
the next time the completion interrupt is enabled.
To avoid previous command completions interfering with new commands,
clear all pending completion interrupts before re-enabling them for
a new command.
Fixes: b4175f8731 ("net: ipa: only enable GSI event control IRQs when needed")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the core clock rate and interconnect bandwidth specifications
were moved into configuration data, a copy/paste bug was introduced,
causing the memory interconnect bandwidth to be set three times
rather than enabling the three different interconnects.
Fix this bug.
Fixes: 91d02f9551 ("net: ipa: use config data for clocking")
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201222151613.5730-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the coherent memory is freed in gsi_trans_pool_exit_dma(), we
are mistakenly passing the size of a single element in the pool
rather than the actual allocated size. Fix this bug.
Fixes: 9dd441e4ed ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201203215106.17450-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jon Hunter reported observing a build bug in the IPA driver:
https://lore.kernel.org/netdev/5b5d9d40-94d5-5dad-b861-fd9bef8260e2@nvidia.com
The problem is that the QMB0 max read value set for IPA v4.5 (16) is
too large to fit in the 4-bit field.
The actual value we want is 0, which requests that the hardware use
the maximum it is capable of.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201202141502.21265-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend ipa_reg_init_hol_block_timer_val() so it properly calculates
the head-of-line block timeout to use for IPA v4.5.
Introduce hol_block_timer_qtime_val() to compute the value to use
for IPA v4.5, where Qtime is used as the basis of the timer. Call
that function from hol_block_timer_val() for IPA v4.5.
Both of these are private functions, so shorten their names a bit so
they don't take up so much space on the line.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change aggr_time_limit_encoded() to properly calculate the
aggregation time limit to use for IPA v4.5.
Older IPA versions program the AGGR_GRANULARITY field of the
of the COUNTER_CFG register to set the granularity of the
aggregation timer, which we configure to be 500 microseconds.
Instead, IPA v4.5 selects between two possible granularity values
derived from the 19.2 MHz Qtime clock. These granularities are
100 microseconds or 1 millisecond per tick. We use the smaller
granularity if possible, unless the desired period is too large
to be specified that way.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA v4.5 introduces a new unified timer architecture driven on the
19.2 MHz SoC crystal oscillator (XO). It is independent of the IPA
core clock and avoids some duplication.
Lower-resolution time stamps are derived from this by using only the
high-order bits of the 19.2 MHz Qtime clock. And timers are derived
from this based on "pulse generators" configured to fire at a fixed
rate based on the Qtime clock.
This patch introduces ipa_qtime_config(), which configures the Qtime
mechanism for use. It also adds to the IPA register definitions
related to timers and time stamping.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA v4.5 significantly changes the format of the configuration
register used for endpoint aggregation. The AGGR_BYTE_LIMIT field
is now larger, and the positions of other fields are shifted. This
complicates the way we have to access this register because functions
like u32_encode_bits() require their field mask argument to be constant.
A further complication is that we want to know the maximum value
representable by at least one of these fields, and that too requires
a constant field mask.
This patch adds support for IPA v4.5 endpoint aggregation registers
in a way that continues to support "legacy" IPA hardware. It does
so in a way that keeps field masks constant.
First, for each variable field mask, we define an inline function
whose return value is either the legacy value or the IPA v4.5 value.
Second, we define functions for these fields that encode a value
to use in each field based on the IPA version (this approach is
already used elsewhere). The field mask provided is supplied by
the function mentioned above.
Finally, for the aggregation byte limit fields where we want to
know the maximum representable value, we define a function that
returns that maximum, computed from the appropriate field mask.
We can no longer verify at build time that our buffer size is
in the range that can be represented by the aggregation byte
limit field. So remove the test done by a BUILD_BUG_ON() call
in ipa_endpoint_validate_build(), and implement a comparable check
at the top of ipa_endpoint_data_valid().
Doing that makes ipa_endpoint_validate_build() contain a single
line BUILD_BUG_ON() call, so just remove that function and move
the remaining line into ipa_endpoint_data_valid().
One final note: the aggregation time limit value for IPA v4.5 needs
to be computed differently. That is handled in an upcoming patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The offsets for almost all GSI registers we use have different
offsets starting at IPA version 4.5. Only two registers remain
in their original location.
In a way though, the new register locations are not *that*
different. The entire group of affected registers has simply
been shifted down in memory by a fixed amount (0xd000). So for
example, the channel context 0 register that has a base offset of
0x0001c000 for "older" hardware now has a base offset of 0x0000f000.
This patch aims to add support for IPA v4.5 registers at their new
offets in a way that minimizes the amount of code that needs to
change. It is not ideal, but it avoids the need to maintain
a nearly complete set of additional register offset definitions.
The approach takes advantage of the fact that when accessing GSI
registers we do not access any of memory at lower end of the "gsi"
memory range (with two exceptions already noted). In particular,
we do not access anything within the bottom 0xd000 bytes of the
GSI memory range.
For IPA version 4.5, after we map the GSI memory, we adjust the
virtual memory pointer downward by the fixed amount (0xd000).
That way, register accesses using the offsets defined by the
existing GSI_REG_*() macros will resolve to the proper locations
for IPA version 4.5.
The two registers *not* affected by this offset are accessed only
in gsi_irq_setup(). There, for IPA version 4.5, we undo the general
register adjustment by adding the fixed amount back to the virtual
address to access these registers.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Very few GSI register definitions change for IPA v4.5, however
as a group their position in memory shifts a constant amount
(handled by the next commit).
Add definitions and update comments to the set of GSI registers to
support changes that come with IPA v4.5.
Update the logic in gsi_channel_program() to accommodate the new
(expanded) PREFETCH_MODE field in the CH_C_QOS register.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the IPA code to make use of the updated IPA v4.5 register
definitions. Generally what this patch does is, if IPA v4.5
hardware is in use:
- Ensure new registers or fields in IPA v4.5 are updated where
required
- Ensure registers or fields not supported in IPA v4.5 are not
examined when read, or are set to 0 when written
It does this while preserving the existing functionality for IPA
versions lower than v4.5.
The values to program for QSB_MAX_READS and QSB_MAX_WRITES and the
source and destination resource counts are updated to be correct for
all versions through v4.5 as well.
Note that IPA_RESOURCE_GROUP_SRC_MAX and IPA_RESOURCE_GROUP_DST_MAX
already reflect that 5 is an acceptable number of resources (which
IPA v4.5 implements).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA v4.5 adds a few fields to the endpoint header and extended
header configuration registers that represent new high-order bits
for certain offsets and sizes. Add code to incorporate these upper
bits into the registers for IPA v4.5.
This includes creating ipa_header_size_encoded(), which handles
encoding the metadata offset field for use in the ENDP_INIT_HDR
register in a way appropriate for the hardware version. This and
ipa_metadata_offset_encoded() ensure the mask argument passed to
u32_encode_bits() is constant.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update "ipa_reg.h" so that register definitions support IPA hardware
version 4.5, in addition to versions 3.5.1 through v4.2. Most of
the register definitions are the same, but in some cases fields are
added, changed, or eliminated.
Updates for a few IPA v4.5 registers are more complex, and adding
those definition will be deferred to separate patches. This patch
only updates the register offset and field definitions, and adds
informational comments.
The only code change avoids accessing the backward compatibility
register for IPA version 4.5 in ipa_hardware_config(). Other IPA
v4.5-specific code changes will come later.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with IPA v4.2 there is a GSI channel option to use an
"escape buffer" instead of prefetch buffers. This should be used
for all channels *except* the AP command TX channel. The logic
that implements this has it backwards; fix this bug.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are only used as input arguments to qmi_handle_init() which
accepts const pointers to both qmi_ops and qmi_msg_handler. Make them
const to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201122234031.33432-2-rikard.falkeborn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A system shutdown can happen at essentially any time, and it's
possible that the IPA driver is busy when a shutdown is underway.
IPA hardware accesses IMEM and SMEM memory regions using an IOMMU,
and at some point during shutdown, needed I/O mappings could become
invalid. This could be disastrous for any "in flight" IPA activity.
Avoid this by defining a new driver shutdown callback that stops all
IPA activity and cleanly shuts down the driver. It merely calls the
driver's existing remove callback, reporting the error if it returns
one.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA driver remove callback, ipa_remove(), calls ipa_modem_stop()
if the setup stage of initialization is complete. If a concurrent
call to ipa_modem_start() or ipa_modem_stop() has begin but not
completed, ipa_modem_stop() can return an error (-EBUSY).
The next patch adds a driver shutdown callback, which will simply
call ipa_remove(). We really want our shutdown callback to clean
things up. So add a single retry to the ipa_modem_stop() call in
ipa_remove() after a short (millisecond) delay. This offers no
guarantee the shutdown will complete successfully, but we'll at
least try a little harder before giving up.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When stopping an AP RX channel, there can be a transient period
while the channel enters STOP_IN_PROC state before reaching the
final STOPPED state. In that case we make another attempt to stop
the channel.
Similarly, when stopping a modem channel (using a GSI generic
command issued from the AP), it's possible that multiple attempts
will be required before the channel reaches STOPPED state.
Add a field to the GSI structure to record an errno representing the
result code provided when a generic command completes. If the
result learned in gsi_isr_gp_int1() is RETRY, record -EAGAIN in the
result code, otherwise record 0 for success, or -EIO for any other
result.
If we time out nf gsi_generic_command() waiting for the command to
complete, return -ETIMEDOUT (as before). Otherwise return the
result stashed by gsi_isr_gp_int1().
Add a loop in gsi_modem_channel_halt() to reissue the HALT command
if the result code indicates -EAGAIN. Limit this to 10 retries
(after the initial attempt).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA v4.2 has a hardware quirk that requires the AP to allocate GSI
channels for the modem to use. It is recommended that these modem
channels get stopped (with a HALT generic command) by the AP when
its IPA driver gets removed.
The AP has no way of knowing the current state of a modem channel.
So when the IPA driver issues a HALT command it's possible the
channel is not running, and in that case we get an error indication.
This error simply means we didn't need to stop the channel, so we
can ignore it.
This patch adds an explanation for this situation, and arranges for
this condition to *not* report an error message.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the rmnet_ipa0 network device has not been opened at the time
we remove or shut down the IPA driver, its underlying TX and RX
GSI channels will not have been started, and they will still be
in ALLOCATED state.
The RESET command on a channel is meant to return a channel to
ALLOCATED state after it's been stopped. But if it was never
started, its state will still be ALLOCATED, the RESET command
is not required.
Quietly skip doing the reset without printing an error message if a
channel is already in ALLOCATED state when we request it be reset.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a GSI command is used to change the state of a channel or event
ring we check the state before and after the command to ensure it is
as expected. If not, we print an error message, but it does not
include the channel or event ring id, and it easily can. Add the
channel or event ring id to these error messages.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stop assuming a fixed IPA core clock rate and interconnect
bandwidths. Use the configuration data defined for these
things instead. Get rid of the previously-used constants.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Populate the core clock rate and interconnect average and peak
bandwidth data for SDM845 and SC7180 in their configuration data
files. At this point we still don't *use* this data.
Note that SC7180 actually defines a new core clock rate (100 MHz
instead of 75 MHz) and new interconnect bandwidth values. They
will be activated in the next commit, which uses the configured
values rather than the fixed constants.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define a new type of configuration data, used to initialize the
IPA core clock and interconnects. This is the first of three
patches, and defines the data types and interface but doesn't
yet use them.
Switch the return value if there is no matching configuration data
to ENODEV instead of ENOTSUPP (to avoid using the nonstandard errno).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some last cleanups for the existing IPA register definitions:
- Remove the definition of IPA_REG_ENABLED_PIPES_OFFSET, because
it is not used.
- Use "IPA_" instead of "BAM_" as the prefix on fields associated
with the FLAVOR_0 register. We use GSI (not BAM), but the
fields apply to both GSI and BAM.
- Get rid of the definition of IPA_CS_RSVD; it is never used.
- Add two missing field mask definitions for the INIT_DEAGGR
endpoint register.
- Eliminate a few of the defined sequencer types, because they
are unused. We can add them back when needed.
- Add a field mask to indicate which bit causes an interrupt on
the microcontroller.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the definition of the ipa_irq_id enumerated type out of
"ipa_interrupt.h" and into "ipa_reg.h", and flesh out its set of
defined values. Each interrupt id indicates a particular type of
IPA interrupt that can be signaled. Their numeric values define bit
positions in the IPA_IRQ_* registers, so should their definitions
should accompany the definition of those register offsets.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move a few things around in "ipa_reg.h":
- Move the definition of ipa_reg_state_aggr_active_offset() down
a bit in the file so definitions are ordered by offset (for
the lowest supported IPA version) like all other definitions.
- Move the definition TIMER_FREQUENCY to be immediately above
the definition of ipa_aggr_granularity_val() where it's used.
- Move each register field value enumerated type definition to
immediately follow the definitions of the register and field
it is associated with.
No code functionality is modified by this patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Revise or add comments in "ipa_reg.h" for to provide more
information, and to improve clarity and consistency.
- Always provide a comment to define when a register or field is
supported (or not) for certain versions of IPA hardware.
- Try to be specific about *which* or *how many* definitions
a comment refers to.
- Move comments stating that ipa->available defines the valid
bits in various registers *above* the register offset
definition, to avoid some checkpatch.pl warnings.
No code is changed by this patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Consistently define numeric values for enumerated type members using
hexidecimal (rather than decimal) format values. Align the values
assigned in the same column in each file.
Only assign values where they really matter, for example don't
assign IPA_ENDPOINT_AP_MODEM_TX the value 0.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The backward compatibility register field masks are defined using
single-bit masks defined with BIT(x) rather than GENMASK(x, x).
Change this one set of definitions to follow the GENMASK() pattern
used everywhere else. Add a few missing field definitions for this
register as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Several IPA register field masks are defined without the "_FMASK"
suffix naming convention. Rename these, so all field masks are
consistently named.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename two suspend IRQ registers so they follow the IPA_REG_IRQ_xxx
naming convention used elsewhere.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA version 3.5.1 represents the timer used in avoiding head-of-line
blocking with a simple tick count. IPA v4.2 changes that, instead
splitting the timer field into two parts (base and scale) to
represent the ticks in the timer period.
IPA v4.0 and IPA v4.1 use the same method as IPA v3.5.1. Change the
test in ipa_reg_init_hol_block_timer_val() so the result is correct
for those versions as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For IPA v3.5.1, the IPA filter/routing hash enable register actually
does exist, but it is at offset 0x8c into the IPA register space.
For newer versions of IPA it is at offset 0x148.
Define a new inline function ipa_reg_filt_rout_hash_en_offset() to
return the appropriate value for a given version of IPA hardware.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA filter/routing hash enable register and filter/routing hash
flush register each have four single-bit fields representing the
four hashed tables to be enabled or flushed. The field positions
are identical, so just use a single set of field masks to represent
the fields for both registers.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Transactions sit on one of several lists, depending on their state
(allocated, pending, complete, or polled). A spinlock protects
against concurrent access when transactions are moved between these
lists.
Transactions are also reference counted. A newly-allocated
transaction has an initial count of 1; a transaction is released in
gsi_trans_free() only if its decremented reference count reaches 0.
Releasing a transaction includes removing it from the polled (or if
unused, allocated) list, so the spinlock is acquired when we release
a transaction.
The reference count is used to allow a caller to synchronously wait
for a committed transaction to complete. In this case, the waiter
takes an extra reference to the transaction *before* committing it
(so it won't be freed), and releases its reference (calls
gsi_trans_free()) when it is done with it.
Similarly, gsi_channel_update() takes an extra reference to ensure a
transaction isn't released before the function is done operating on
it. Until the transaction is moved to the completed list (by this
function) it won't be freed, so this reference is taken "safely."
But in the quiesce path, we want to wait for the "last" transaction,
which we find in the completed or polled list. Transactions on
these lists can be freed at any time, so we (try to) prevent that
by taking the reference while holding the spinlock.
Currently gsi_trans_free() decrements a transaction's reference
count unconditionally, acquiring the lock to remove the transaction
from its list *only* when the count reaches 0. This does not
protect the quiesce path, which depends on the lock to ensure its
extra reference prevents release of the transaction.
Fix this by only dropping the last reference to a transaction
in gsi_trans_free() while holding the spinlock.
Fixes: 9dd441e4ed ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201114182017.28270-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA-resident microcontroller has the ability to log various
activity in an area of IPA shared memory. When the microcontroller
starts it generates an event to the AP to provide information about
the log.
We don't support reading this log, and we can safely ignore the
event. So do that rather than treating the log info event we
receive as "unsupported."
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I have discovered that the maximum number of source packet contexts
configured for SDM845 is incorrect. Fix this error.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace constants defined with an "_FVAL" suffix with values defined
in enumerated types, to be consistent with other usage in the driver.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The gsi_ch_cmd_opcode, gsi_evt_cmd_opcode, and gsi_generic_cmd_opcode
enumerated types are values that fields in the GSI command registers
can take on. Move their definitions out of "gsi.c" and into "gsi_reg.h",
alongside the definition of registers they are associated with.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The gsi_err_code and gsi_err_type enumerated types are values that
fields in the GSI ERROR_LOG register can take on. Move their
definitions out of "gsi.c" and into "gsi_reg.h", alongside the
definition of the ERROR_LOG register offset and field symbols.
Drop the "_ERR" suffix in the names of the gsi_err_code members.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The gsi_channel_type enumerated type define values used for the
channel type/protocol for event rings and channels. Move its
definition out of "gsi.c" and into "gsi_reg.h", alongside the
definition of the CH_C_CNTXT_0 register offset and its fields.
Add a comment near the definition of the EV_CH_E_CNTXT_0 register
indicating this type is used for its EV_CHTYPE field.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The numeric values that represent the event ring channel type are
identical to the values that represent the matching protocol used
for a channel. Use a new gsi_channel_type enumerated type to
represent the values programmed for both cases, using "CHANNEL_TYPE"
in member names in place of "EVT_CHTYPE" and "CHANNEL_PROTOCOL".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define the GSI global interrupt types with an enumerated type whose
values are the bit positions representing the global interrupt types.
Similarly, define the GSI general interrupt types with an enumerated
type whose values are the bit positions of general interrupt types.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need for gsi_modem_channel_halt() to report an error,
because gsi_generic_command() will already have done that if the
command times out. So get rid of the extra message.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When we determine from hardware what the size of IPA memory is
we compare it against what we learned about it from DT.
If DT defines a region that's larger than actual memory, we use the
smaller actual size and issue a warning.
If DT defines a smaller region than actual memory we issue a warning
too. But in this case the difference is harmless; so rather than
issuing a warning, just provide a debug message instead.
Reorder these checks so the one that matters more is done first.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Delete a spurious line of code in ipa_hardware_config(). It reads a
register value then ignores the value, so is completely unnecessary.
Add a missing word in a comment.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following call in ipa_validate_build() is erroneous:
BUILD_BUG_ON(sizeof(struct gsi_trans) > 128);
The fact is, it is not a bug for the size of a GSI transaction to be
bigger than 128 bytes. The correct operation of the driver is not
dependent on the size of this structure. The only consequence of
the transaction being large is that the amount of memory required
is larger.
The problem this was trying to flag is that a *slight* increase in
the size of this structure will have a disproportionate effect on
the amount of memory used. E.g. if the structure grew to 132 bytes
the memory requirement for the transaction arrays would be about
double.
With various debugging build flags enabled, the size grows to 160
bytes. But there's no reason to treat that as a build-time bug.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all of the GSI interrupts are handled uniformly,
change gsi_irq_type_update() so it takes a value. Have the
function assign that value to the cached mask of enabled GSI
IRQ types before writing it to hardware.
Note that gsi_irq_teardown() will only be called after
gsi_irq_disable(), so it's not necessary for the former
to disable all IRQ types. Get rid of that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most GSI general errors are unrecoverable without a full reset.
Despite that, we want to receive these errors so we can at least
report what happened before whatever undefined behavior ensues.
Explicitly disable all such interrupts in gsi_irq_setup(), then
enable those we want in gsi_irq_enable(). List the interrupt types
we are interested in (everything but breakpoint) explicitly rather
than using GSI_CNTXT_GSI_IRQ_ALL, and remove that symbol's
definition.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is possible for other execution environments (EEs, like the modem)
to request changes to local (AP) channel or event ring state. We do
not support this feature.
In gsi_irq_setup(), explicitly zero the mask that defines which
channels are permitted to generate inter-EE channel state change
interrupts. Do the same for the event ring mask.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A GSI channel must be started in order to use it to perform a
transfer data (or command) transaction. And the only time we'll see
an IEOB interrupt is if we send a transaction to a started channel.
Therefore we do not need to have the IEOB interrupt type enabled
until at least one channel has been started. And once the last
started channel has been stopped, we can disable the IEOB interrupt
type again.
We already enable the IEOB interrupt for a particular channel only
when it is started. Extend that by having the IEOB interrupt *type*
be enabled only when at least one channel is in STARTED state.
Disallow all channels from triggering the IEOB interrupt in
gsi_irq_setup(). We only enable an channel's interrupt when
needed, so there is no longer any need to zero the channel mask
in gsi_irq_disable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The completion of a generic EE GSI command is signaled by a global
interrupt of type GP_INT1. The only other used type for a global
interrupt is a hardware error report.
First, disallow all global interrupt types in gsi_irq_setup(). We
want to know about hardware errors, so re-enable the interrupt type
in gsi_irq_enable(), to allow hardware errors to be reported.
Disable that interrupt type again in gsi_irq_disable().
We only issue generic EE commands one at a time, and there's no
reason to keep the completion interrupt enabled when no generic
EE command is pending. We furthermore have no need to enable the
GP_INT2 or GP_INT3 interrupt types (which aren't used).
The change in gsi_irq_enable() makes GSI_CNTXT_GLOB_IRQ_ALL unused,
so get rid of it. Have gsi_generic_command() enable the GP_INT1
interrupt type (in addition to the ERROR_INT type) only while a
generic command is pending.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A GSI event ring causes an event control interrupt to fire whenever
its state changes (between NOT_ALLOCATED and ALLOCATED). No event
ring should ever change state except when we request it to.
Currently, we permit *all* events rings to generate event control
interrupts--even those that are never used. And we enable event
control interrupts essentially at all times, from setup to teardown.
Instead, only enable the event control interrupt type for the
duration of an event ring command, and when doing so, only allow
the event ring being operated upon to cause the interrupt to fire.
Disallow all event rings from issuing the event control interrupt
in gsi_irq_setup().
Because an event ring's interrupt is only enabled when needed,
there is no longer any need to zero the event channel mask in
gsi_irq_disable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A GSI channel causes a channel control interrupt to fire whenever
its state changes (between NOT_ALLOCATED, ALLOCATED, STARTED, etc.).
We do not support inter-EE channel commands (initiated by other EEs),
so no channel should ever change state except when we request it to.
Currently, we permit *all* channels to generate channel control
interrupts--even those that are never used. And we enable channel
control interrupts essentially at all times, from setup to teardown.
Instead, disable all channel control interrupts initially in
gsi_irq_setup(), and only enable the channel control interrupt
type for the duration of a channel command. When doing so, only
allow the channel being operated upon to cause the interrupt to
fire.
Because a channel's interrupt is now enabled only when needed (one
channel at a time), there is no longer any need to zero the channel
mask in gsi_irq_disable().
Add new gsi_irq_type_enable() and gsi_irq_type_disable() as helper
functions to control whether a given GSI interrupt type is enabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Keep track of the set of GSI interrupt types that are currently
enabled by recording the mask value to write (or last written) to
the TYPE_IRQ_MSK register.
Create a new helper function gsi_irq_type_update() to handle
actually writing the register.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce gsi_irq_setup() and gsi_irq_teardown() to disable all
GSI interrupts when first setting up GSI hardware, and to clean
things up when we're done.
Re-enable all GSI interrupt types in gsi_irq_enable(), but do
so only after each of the type-specific interrupt masks has
been configured. Similarly, disable all interrupt types in
gsi_irq_disable()--first--before zeroing out the type-specific
masks.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define the GSI interrupt types with an enumerated type whose values
are the bit positions representing each interrupt type. Include a
short comment describing how each interrupt type is used.
Build up the enabled interrupt mask explicitly in gsi_irq_enable(),
and get rid of the definition of GSI_CNTXT_TYPE_IRQ_MSK_ALL.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename the "event_enable_bitmap" field of the GSI structure to be
"ieob_enabled_bitmap". An upcoming patch will cache the last value
stored for another interrupt mask and this is a more direct naming
convention to follow.
Add a few comments to explain the bitmap fields in the GSI structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce gsi_irq_init() and gsi_irq_exit(), to encapsulate looking
up the GSI IRQ and registering its handler. Call gsi_irq_init() a
little later in gsi_init(), and initialize the completion earlier.
The IRQ handler accesses both the GSI virtual memory pointer and the
completion, and this way these things will have been initialized
before the gsi_irq() can ever be called.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The GSI code is now exposed to IPA version numbers, and we handle
version-specific behavior based on the IPA version.
Modify some comments that talk about GSI versions so they reference
IPA versions instead. Correct version number errors in a couple of
these comments.
The (comment) mapping between IPA and GSI versions in the definition
of the ipa_version enumerated type remains.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We enable a channel doorbell engine only for IPA v3.5.1, and that is
now handled directly by gsi_channel_program().
When initially setting up a channel, we want that doorbell engine
enabled, and we can request that independent of the IPA version.
Doing that makes the "legacy" argument to gsi_channel_setup_one()
unnecessary. And with that gone we can get rid of the "legacy"
argument to gsi_channel_setup(), and gsi_setup() as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the IPA version in gsi_channel_program() to determine whether
we should enable the GSI doorbell engine when requested. This way,
callers only say whether or not it should be enabled if needed,
regardless of hardware version.
Rename the "legacy" argument to gsi_channel_reset(), and have
it indicate whether the doorbell engine should be enabled when
reprogramming following the reset.
Change all callers of gsi_channel_reset() to indicate whether to
enable the doorbell engine after reset, independent of hardware
version.
Rework a little logic in ipa_endpoint_reset() to get rid of the
"legacy" variable previously passed to gsi_channel_reset().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A quirk of IPA v3.5.1 requires a channel reset on an RX channel to
be performed twice. Use the IPA version in gsi_channel_reset()
rather than the passed-in legacy flag to determine that.
This is actually a bug fix, because this double reset is supposed
to occur independent of whether we're enabling the doorbell engine.
Now they will be independent.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A quirk of IPA v4.2 requires the AP to allocate the GSI channels
that are owned by the modem.
Rather than pass a flag argument to gsi_channel_init(), use the
IPA version directly in that function to determine whether modem
channels need to be allocated.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Record the IPA version passed to gsi_init() in the GSI structure.
This allows that value to be used directly where needed, rather than
passing and storing certain flag arguments through the code.
In particular, for all but one supported version of IPA, the command
channel is programmed to only use an "escape buffer". By storing
the IPA version, we can do a simple version check in one location,
and avoid storing a flag field in every channel (and passing a flag
along while initializing channels to set that field properly).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Although GSI is integral to IPA, it is a separate hardware component
and the IPA code supporting it has been structured to avoid explicit
dependence on IPA details. An example of this is that gsi_init() is
passed a number of Boolean flags to indicate special behaviors,
whose values are dependent on the IPA hardware version. Looking
ahead, newer hardware versions would require even more such special
behaviors.
For any given version of IPA hardware (like 3.5.1 or 4.2), the GSI
hardware version is fixed (in this case, 1.3 and 2.2, respectively).
So the IPA version *implies* the GSI version, and the IPA version
can be used as effectively the equivalent of the GSI hardware version.
Rather than proliferating new special behavior flags, just provide
the IPA version to the GSI layer when it is initialized. The GSI
code can then use that directly to determine whether special
behaviors are required. The IPA version enumerated type is already
isolated to its own header file, so the exposure of this IPA detail
is very limited.
For now, just change gsi_init() to pass the version rather than the
Boolean flags, and set the flag values internal to that function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With IPA v3.5.1, if IPA aggregation is active at the time an
underlying GSI channel reset is performed, some special handling
is required.
There is logic in ipa_endpoint_reset() that arranges for that
special handling, but it's done for all hardware versions, not
just IPA v3.5.1.
Fix the logic to properly restrict the special behavior.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201102173435.5987-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous commit added support for IPA having up to six source
and destination resources. But currently nothing uses more than
four. (Five of each are used in a newer version of the hardware.)
I find that in one of my build environments the compiler complains
about newly-added code in two spots. Inspection shows that the
warnings have no merit, but this compiler does not recognize that.
ipa_main.c:457:39: warning: array index 5 is past the end of the
array (which contains 4 elements) [-Warray-bounds]
(and the same warning at line 483)
We can make this warning go away by changing the number of elements
in the source and destination resource limit arrays--now rather than
waiting until we need it to support the newer hardware. This change
was coming soon anyway; make it now to get rid of the warning.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201031151524.32132-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The minimum and maximum limits for resources assigned to a given
resource group are programmed in pairs, with the limits for two
groups set in a single register.
If the number of supported resource groups is odd, only half of the
register that defines these limits is valid for the last group; that
group has no second group in the pair.
Currently we ignore this constraint, and it turns out to be harmless,
but it is not guaranteed to be. This patch addresses that, and adds
support for programming the 5th resource group's limits.
Rework how the resource group limit registers are programmed by
having a single function program all group pairs rather than having
one function program each pair. Add the programming of the 4-5
resource group pair limits to this function. If a resource group is
not supported, pass a null pointer to ipa_resource_config_common()
for that group and have that function write zeroes in that case.
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The number of resource groups supported by the hardware can be
different for source and destination resources. Determine the
number supported for each using separate functions. Make the
functions inline end move their definitions into "ipa_reg.h",
because they determine whether certain register definitions are
valid. Pass just the IPA hardware version as argument.
IPA_RESOURCE_GROUP_COUNT represents the maximum number of resource
groups the driver supports for any hardware version. Change that
symbol to be two separate constants, one for source and the other
for destination resource groups. Rename them to end with "_MAX"
rather than "_COUNT", to reflect their true purpose.
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA hardware manages various resources (e.g. descriptors)
internally to perform its functions. The resources are grouped,
allowing different endpoints to use separate resource pools. This
way one group of endpoints can be configured to operate unaffected
by the resource use of endpoints in a different group.
Endpoints should be assigned to a resource group, but we currently
don't do that.
Define a new resource_group field in the endpoint configuration
data, and use it to assign the proper resource group to use for
each AP endpoint.
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mask for the RSRC_GRP field in the INIT_RSRC_GRP endpoint
initialization register is incorrectly defined for IPA v4.2 (where
it is only one bit wide). So we need to fix this.
The fix is not straightforward, however. Field masks are passed to
functions like u32_encode_bits(), and for that they must be constant.
To address this, we define a new inline function that returns the
*encoded* value to use for a given RSRC_GRP field, which depends on
the IPA version. The caller can then use something like this, to
assign a given endpoint resource id 1:
u32 offset = IPA_REG_ENDP_INIT_RSRC_GRP_N_OFFSET(endpoint_id);
u32 val = rsrc_grp_encoded(ipa->version, 1);
iowrite32(val, ipa->reg_virt + offset);
The next patch requires this fix.
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At the end of ipa_mem_setup() we write the local packet processing
context base register to tell it where the processing context memory
is. But we are writing the wrong value.
The value written turns out to be the offset of the modem header
memory region (assigned earlier in the function). Fix this bug.
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA transactions describe actions to be performed by the IPA
hardware. Three cases use IPA transactions: transmitting a socket
buffer; providing a page to receive packet data; and issuing an IPA
immediate command. An IPA transaction contains a scatter/gather
list (SGL) to hold the set of actions to be performed.
We map buffers in the SGL for DMA at the time they are added to the
transaction. For skb TX transactions, we fill the SGL with a call
to skb_to_sgvec(). Page RX transactions involve a single page
pointer, and that is recorded in the SGL with sg_set_page(). In
both of these cases we then map the SGL for DMA with a call to
dma_map_sg().
Immediate commands are different. The payload for an immediate
command comes from a region of coherent DMA memory, which must
*not* be mapped for DMA. For that reason, gsi_trans_cmd_add()
sort of hand-crafts each SGL entry added to a command transaction.
This patch fixes a problem with the code that crafts the SGL entry
for an immediate command. Previously a portion of the SGL entry was
updated using sg_set_buf(). However this is not valid because it
includes a call to virt_to_page() on the buffer, but the command
buffer pointer is not a linear address.
Since we never actually map the SGL for command transactions, there
are very few fields in the SGL we need to fill. Specifically, we
only need to record the DMA address and the length, so they can be
used by __gsi_trans_commit() to fill a TRE. We additionally need to
preserve the SGL flags so for_each_sg() still works. For that we
can simply assign a null page pointer for command SGL entries.
Fixes: 9dd441e4ed ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201022010029.11877-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When processing a system suspend request we suspend modem endpoints
if they are enabled, and call ipa_cmd_tag_process() (which issues
IPA commands) to ensure the IPA pipeline is cleared. It is an error
to attempt to issue an IPA command before setup is complete, so this
is clearly a bug. But we also shouldn't suspend or resume any
endpoints that have not been set up.
Have ipa_endpoint_suspend() and ipa_endpoint_resume() immediately
return if setup hasn't completed, to avoid any attempt to configure
endpoints or issue IPA commands in that case.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_uc_response_hdlr() a comment uses the wrong function name
when it describes where a clock reference is taken. Fix this.
Also fix the comment in ipa_uc_response_hdlr() to correctly refer to
ipa_uc_setup(), which is where the clock reference described here is
taken.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When "W=2" is supplied to the build command, we get a warning about
shadowing a global declaration (of a typedef) for a variable defined
in ipa_probe(). Rename the variable to get rid of the warning.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two spots where a variable "channel_id" is unnecessarily
redefined inside loops in "gsi.c". This is warned about if
"W=2" is added to the build command.
Note that this problem is harmless, so there's no need to backport
it as a bugfix.
Remove a comment in gsi_init() about waking the system; the GSI
interrupt does not wake the system any more.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI general interrupt is managed by three registers: enable;
status; and clear. The three registers have same set of field bits
at the same locations. Use a common set of field masks for all
three registers to avoid duplication.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI global interrupt is managed by three registers: enable;
status; and clear. The three registers have same set of field bits
at the same locations. Use a common set of field masks for all
three registers to avoid duplication.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI interrupt type register and interrupt type mask register
have the same field bits at the same locations. Use a common set of
field masks for both registers rather than essentially duplicating
them. The only place the interrupt mask register uses any of these
is in gsi_irq_enable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the field masks used for fields in a status structure are
unused. Remove their definitions; we can add them back again when
we actually use them to handle arriving status messages. These are
warned about if "W=2" is added to the build command.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the deaggregation status exception type is ever actually used.
If any other status exception type is reported we basically ignore
it, and consume the packet. Remove the unused definitions of status
exception type symbols; they can be added back when we actually
handle them.
Separately, two consecutive if statements test the same condition
near the top of ipa_endpoint_suspend_one(). Instead, use a single
test with a block that combines the previously-separate lines of
code.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three status opcodes are not currently supported. Symbols
representing their numeric values are defined but never used.
Remove those unused definitions; they can be defined again
when they actually get used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In "gsi_trans.c", the field mask TRE_FLAGS_IEOB_FMASK is defined but
never used. Although there's no harm in defining this, remove it
for now and redefine it at some future date if it becomes needed.
This is warned about if "W=2" is added to the build command.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
We now trigger a system resume when we receive an IPA SUSPEND
interrupt. We should *not* wake up on GSI interrupts.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we handle wakeup interrupts properly, arrange for the IPA
interrupt to be treated as a wakeup interrupt.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch causes a system resume to be triggered when a
packet is available for receipt on a suspended RX endpoint.
The CLOCK_HELD flag was previously used to indicate that an extra
clock reference was held, preventing suspend. But we no longer need
such a flag:
- We take an initial reference in ipa_config().
- That reference is held until ipa_suspend() releases it.
- A subsequent system resume leads to a reference getting
re-acquired in ipa_resume().
- This can repeat until ultimately the module is removed, where
ipa_remove() releases the reference.
We no longer need a special flag to determine whether this extra
reference is held--it is, provided probe has completed successfully
and the driver is not suspended (or removed).
On the other hand, once suspended, it's possible for more than one
endpoint to trip the IPA SUSPEND interrupt, and we only want to
trigger the system resume once. So repurpose the Boolean CLOCK_HELD
flag to record whether the IPA SUSPEND handler should initiate a
system resume.
The flag will be be cleared each time ipa_suspend() is called,
*before* any endpoints are suspended. And it will be set inside the
IPA SUSPEND interrupt handler exactly once per suspend.
Rename the flag IPA_FLAG_RESUMED to reflect its new purpose.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to wakeup_source_register() in ipa_probe() does not do what
it was intended to do. Call device_init_wakeup() in ipa_setup()
instead, to set the IPA device as wakeup-capable and to initially
enable wakeup capability.
When we receive a SUSPEND interrupt, call pm_wakeup_dev_event()
with a zero processing time, to simply call for a resume without
any other processing. The ipa_resume() call will take care of
waking things up again, and will handle receiving the packet.
Note that this gets rid of a clock reference counting bug that
occurred when handling an IPA SUSPEND interrupt. Specifically,
ipa_suspend_handler() took an IPA clock reference *in addition*
to the one taken by ipa_resume(). There is no need to back-port
this fix however, because it only affects code that was not
previously working (this patch is part of fixing that).
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when (before) the last IPA clock reference is dropped,
all endpoints are suspended. And whenever the first IPA clock
reference is taken, all endpoints are resumed (or started).
In most cases there's no need to start endpoints when the clock
starts. So move the calls to ipa_endpoint_suspend() and
ipa_endpoint_resume() out of ipa_clock_put() and ipa_clock_get(),
respectiely. Instead, only suspend endpoints when handling a system
suspend, and only resume endpoints when handling a system resume.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
