As documented in Documentation/networking/driver.rst, the ndo_start_xmit
method must not return NETDEV_TX_BUSY under any normal circumstances, and
as recommended, we simply stop the tx queue in advance, when there is a
risk that the next xmit would cause a NETDEV_TX_BUSY return.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.
This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.
Fixes: 84823ff80f ("net: ll_temac: Fix race condition causing TX hang")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple of memory-barriers to ensure correct ordering of read/write
access to TX BDs.
In xmit_done, we should ensure that reading the additional BD fields are
only done after STS_CTRL_APP0_CMPLT bit is set.
When xmit_done marks the BD as free by setting APP0=0, we need to ensure
that the other BD fields are reset first, so we avoid racing with the xmit
path, which writes to the same fields.
Finally, making sure to read APP0 of next BD after the current BD, ensures
that we see all available buffers.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.
Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding a fallthrough statement instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210528195831.GA39131@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Printing kernel pointers is discouraged because they might leak kernel
memory layout. This fixes smatch warning:
drivers/net/ethernet/xilinx/xilinx_emaclite.c:1191 xemaclite_of_probe() warn:
argument 4 to %08lX specifier is cast from pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kernel test robot reports build errors in 3 Xilinx ethernet drivers.
They all use ioremap functions that are only available when HAS_IOMEM
is set/enabled. If it is not enabled, they all have build errors,
so make these 3 drivers depend on HAS_IOMEM.
ld: drivers/net/ethernet/xilinx/xilinx_emaclite.o: in function `xemaclite_of_probe':
xilinx_emaclite.c:(.text+0x9fc): undefined reference to `devm_ioremap_resource'
ld: drivers/net/ethernet/xilinx/xilinx_axienet_main.o: in function `axienet_probe':
xilinx_axienet_main.c:(.text+0x942): undefined reference to `devm_ioremap_resource'
ld: drivers/net/ethernet/xilinx/ll_temac_main.o: in function `temac_probe':
ll_temac_main.c:(.text+0x1283): undefined reference to `devm_platform_ioremap_resource_byname'
ld: ll_temac_main.c:(.text+0x13ad): undefined reference to `devm_of_iomap'
ld: ll_temac_main.c:(.text+0x162e): undefined reference to `devm_platform_ioremap_resource'
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Cc: Gary Guo <gary@garyguo.net>
Cc: Zhang Changzhong <zhangchangzhong@huawei.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: stable@vger.kernel.org
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was only enabling the first clock on the device, regardless
of its name. However, this controller logic can have multiple clocks
which should all be enabled. Add support for enabling additional clocks.
The clock names used are matching those used in the Xilinx version of this
driver as well as the Xilinx device tree generator, except for mgt_clk
which is not present there.
For backward compatibility, if no named clocks are present, the first
clock present is used for determining the MDIO bus clock divider.
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In setups with fixed-link settings there is no mdio node in DTS.
axienet_probe() already handles that gracefully but lp->mii_bus is
then NULL.
Fix code that tries to blindly grab the MDIO lock by introducing two helper
functions that make the locking conditional.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver did not always clean up all allocated resources when probe
failed. Fix the probe cleanup path to clean up everything that was
allocated.
Fixes: 57baf8cc70 ("net: axienet: Handle deferred probe on clock properly")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes made in eccd540 is enough for xilinx_emaclite to run
without problem on 64-bit systems. I have tested it on a Xilinx
FPGA with RV64 softcore. The architecture limitation in Kconfig
seems no longer necessary.
A small change is included to print address with %lx instead of
casting to int and print with %x.
Signed-off-by: Gary Guo <gary@garyguo.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of the Xilinx AXI Ethernet core (specifically version 7.2 or
later) allow the core to be configured with a PHY interface mode of "Both",
allowing either 1000BaseX or SGMII modes to be selected at runtime. Add
support for this in the driver to allow better support for applications
which can use both fiber and copper SFP modules.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook up the nway_reset ethtool operation to the corresponding phylink
function so that "ethtool -r" can be supported.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is set up to use a clock mapping in the device tree if it is
present, but still work without one for backward compatibility. However,
if getting the clock returns -EPROBE_DEFER, then we need to abort and
return that error from our driver initialization so that the probe can
be retried later after the clock is set up.
Move clock initialization to earlier in the process so we do not waste as
much effort if the clock is not yet available. Switch to use
devm_clk_get_optional and abort initialization on any error reported.
Also enable the clock regardless of whether the controller is using an MDIO
bus, as the clock is required in any case.
Fixes: 09a0354cad ("net: axienet: Use clock framework to get device clock rate")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
platform_get_resource() may fail and in this case a NULL dereference
will occur.
Fix it to use devm_platform_ioremap_resource() instead of calling
platform_get_resource() and devm_ioremap().
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve build testing of this driver, add COMPILE_TEST support.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet//xilinx/xilinx_emaclite.c:341:35: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
341 | addr = (void __iomem __force *)((u32 __force)addr ^
Use uintptr_t instead of u32 to avoid problems on 64 bit systems.
Also, cast the address to an unsigned long for printing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The txqueue parameter to the watchdog callback is unused in this
driver. But it still needs to be documented.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MDIO spec does not require an MDC at all times, only when MDIO
transactions are occurring. This patch allows the xilinx_axienet
driver to disable the MDC when not in use, and re-enable it when
needed. It also simplifies the driver by removing MDC disable
and enable in device reset sequence.
Signed-off-by: Clayton Rayment <clayton.rayment@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce helper functions to enable/disable MDIO interface clock. This
change serves a preparatory patch for the coming feature to dynamically
control the management bus clock.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the axienet driver to properly support the Xilinx PCS/PMA PHY
component which is used for 1000BaseX and SGMII modes, including
properly configuring the auto-negotiation mode of the PHY and reading
the negotiated state from the PHY.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20201028171429.1699922-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of the W=1 series for ethernet, these drivers were
discovered to be using kdoc style comments but were not actually
doing kdoc. The kernel uses kdoc style when documenting code, not
doxygen or other styles.
Fixed Warnings:
drivers/net/ethernet/amazon/ena/ena_com.c:613: warning: Function parameter or member 'ena_dev' not described in 'ena_com_set_llq'
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.c:1540: warning: Cannot understand * @brief Set VLAN filter table
drivers/net/ethernet/xilinx/ll_temac_main.c:114: warning: Function parameter or member 'lp' not described in 'temac_indirect_busywait'
drivers/net/ethernet/xilinx/ll_temac_main.c:129: warning: Function parameter or member 'lp' not described in 'temac_indirect_in32'
drivers/net/ethernet/xilinx/ll_temac_main.c:129: warning: Function parameter or member 'reg' not described in 'temac_indirect_in32'
drivers/net/ethernet/xilinx/ll_temac_main.c:147: warning: Function parameter or member 'lp' not described in 'temac_indirect_in32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:147: warning: Function parameter or member 'reg' not described in 'temac_indirect_in32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'lp' not described in 'temac_indirect_out32'
drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'reg' not described in 'temac_indirect_out32'
drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'value' not described in 'temac_indirect_out32'
drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'lp' not described in 'temac_indirect_out32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'reg' not described in 'temac_indirect_out32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'value' not described in 'temac_indirect_out32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:212: warning: Function parameter or member 'lp' not described in 'temac_dma_in32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:212: warning: Function parameter or member 'reg' not described in 'temac_dma_in32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'lp' not described in 'temac_dma_out32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'reg' not described in 'temac_dma_out32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'value' not described in 'temac_dma_out32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:247: warning: Function parameter or member 'lp' not described in 'temac_dma_dcr_in'
drivers/net/ethernet/xilinx/ll_temac_main.c:247: warning: Function parameter or member 'reg' not described in 'temac_dma_dcr_in'
drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'lp' not described in 'temac_dma_dcr_out'
drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'reg' not described in 'temac_dma_dcr_out'
drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'value' not described in 'temac_dma_dcr_out'
drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'lp' not described in 'temac_dcr_setup'
drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'op' not described in 'temac_dcr_setup'
drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'np' not described in 'temac_dcr_setup'
drivers/net/ethernet/xilinx/ll_temac_main.c:300: warning: Function parameter or member 'ndev' not described in 'temac_dma_bd_release'
drivers/net/ethernet/xilinx/ll_temac_main.c:330: warning: Function parameter or member 'ndev' not described in 'temac_dma_bd_init'
drivers/net/ethernet/xilinx/ll_temac_main.c:600: warning: Function parameter or member 'ndev' not described in 'temac_setoptions'
drivers/net/ethernet/xilinx/ll_temac_main.c:600: warning: Function parameter or member 'options' not described in 'temac_setoptions'
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
platform_get_resource() may fail and return NULL, so we had better
check its return value to avoid a NULL pointer dereference a bit later
in the code. Fix it to use devm_platform_ioremap_resource_byname()
instead of calling platform_get_resource_byname() and devm_ioremap().
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a comment. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all DMA address accesses wrapped, we can actually support 64-bit
DMA if this option was chosen at IP integration time.
If the IP has been configured for an address width greater than 32 bits,
we assume the full 64 bit DMA width is working. In practise this will be
limited by the actual system address bus width, which will ideally be the
same as the DMA IP address width.
If this is not the case, the actual width can still be configured using a
dma-ranges property in the parent of the MAC node.
This increases the DMA mask on those systems to let the kernel choose
buffers from memory at higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When newer revisions of the Axienet IP are configured for a 64-bit bus,
we *need* to write to the MSB part of the an address registers,
otherwise the IP won't recognise this as a DMA start condition.
This is even true when the actual DMA address comes from the lower 4 GB.
To autodetect this configuration, at probe time we write all 1's to such
an MSB register, and see if any bits stick. If this is configured for a
32-bit bus, those MSB registers are RES0, so reading back 0 indicates
that no MSB writes are necessary.
On the other hands reading anything other than 0 indicated the need to
write the MSB registers, so we set the respective flag.
The actual DMA mask stays at 32-bit for now. To help bisecting, a
separate patch will enable allocations from higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer revisions of the AXI DMA IP (>= v7.1) support 64-bit addresses,
both for the descriptors itself, as well as for the buffers they are
pointing to.
This is realised by adding "MSB" words for the next and phys pointer
right behind the existing address word, now named "LSB". These MSB words
live in formerly reserved areas of the descriptor.
If the hardware supports it, write both words when setting an address.
The buffer address is handled by two wrapper functions, the two
occasions where we set the next pointers are open coded.
For now this is guarded by a flag which we don't set yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of the Xilink DMA IP support busses with more than 32
address bits, by introducing an MSB word for the registers holding DMA
pointers (tail/current, RX/TX descriptor addresses).
On IP configured for more than 32 bits, it is also *required* to write
both words, to let the IP recognise this as a start condition for an
MM2S request, for instance.
Wrap the DMA pointer writes with a separate function, to add this
functionality later. For now we stick to the lower 32 bits.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii-tool is useful for debugging, and all it requires to work is to wire
up the ioctl ops function pointer.
Add this to the axienet driver to enable mii-tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer revisions of the IP don't have these registers. Since we don't
really use them, just drop them from the ethtools dump.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the DT binding, the Ethernet core interrupt is optional.
Use platform_get_irq_optional() to avoid the error message when the
IRQ is not specified.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Especially with the default 32-bit DMA mask, DMA buffers are a limited
resource, so their allocation can fail.
So as the DMA API documentation requires, add error checking code after
dma_map_single() calls to catch the case where we run out of "low" memory.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code that cleans up a number of connected TX descriptors,
as we will need it to properly roll back a failed _xmit() call.
There are subtle differences between cleaning up a successfully sent
chain (unknown number of involved descriptors, total data size needed)
and a chain that was about to set up (number of descriptors known), so
cater for those variations with some extra parameters.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 0 is a valid DMA address, we cannot use the physical address to
check whether a TX descriptor is valid and is holding a DMA mapping.
Use the "cntrl" member of the descriptor to make this decision, as it
contains at least the length of the buffer, so 0 points to an
uninitialised buffer.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When axienet_dma_bd_init() bails out during the initialisation process,
it might do so with parts of the structure already allocated and
initialised, while other parts have not been touched yet. Before
returning in this case, we call axienet_dma_bd_release(), which does not
take care of this corner case.
This is most obvious by the first loop happily dereferencing
lp->rx_bd_v, which we actually check to be non NULL *afterwards*.
Make sure we only unmap or free already allocated structures, by:
- directly returning with -ENOMEM if nothing has been allocated at all
- checking for lp->rx_bd_v to be non-NULL *before* using it
- only unmapping allocated DMA RX regions
This avoids NULL pointer dereferences when initialisation fails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.
This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.
Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA error handler routine is currently a tasklet, scheduled to run
after the DMA error IRQ was handled.
However it needs to take the MDIO mutex, which is not allowed to do in a
tasklet. A kernel (with debug options) complains consequently:
[ 614.050361] net eth0: DMA Tx error 0x174019
[ 614.064002] net eth0: Current BD is at: 0x8f84aa0ce
[ 614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[ 614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4
[ 614.135428] 3 locks held by kworker/u4:4/40:
[ 614.149075] #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8
[ 614.177528] #1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8
[ 614.209033] #2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58
[ 614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 #26
[ 614.260854] Hardware name: ARM Test FPGA (DT)
[ 614.274734] Workqueue: rpciod rpc_async_schedule
[ 614.289022] Call trace:
[ 614.296871] dump_backtrace+0x0/0x1a0
[ 614.308311] show_stack+0x14/0x20
[ 614.318751] dump_stack+0xbc/0x100
[ 614.329403] ___might_sleep+0xf0/0x140
[ 614.341018] __might_sleep+0x4c/0x80
[ 614.352201] __mutex_lock+0x5c/0x8a8
[ 614.363348] mutex_lock_nested+0x1c/0x28
[ 614.375654] axienet_dma_err_handler+0x38/0x388
[ 614.389999] tasklet_action_common.isra.15+0x160/0x1a8
[ 614.405894] tasklet_action+0x24/0x30
[ 614.417297] efi_header_end+0xe0/0x494
[ 614.429020] irq_exit+0xd0/0xd8
[ 614.439047] __handle_domain_irq+0x60/0xb0
[ 614.451877] gic_handle_irq+0xdc/0x2d0
[ 614.463486] el1_irq+0xcc/0x180
[ 614.473451] __tcp_transmit_skb+0x41c/0xb58
[ 614.486513] tcp_write_xmit+0x224/0x10a0
[ 614.498792] __tcp_push_pending_frames+0x38/0xc8
[ 614.513126] tcp_rcv_established+0x41c/0x820
[ 614.526301] tcp_v4_do_rcv+0x8c/0x218
[ 614.537784] __release_sock+0x5c/0x108
[ 614.549466] release_sock+0x34/0xa0
[ 614.560318] tcp_sendmsg+0x40/0x58
[ 614.571053] inet_sendmsg+0x40/0x68
[ 614.582061] sock_sendmsg+0x18/0x30
[ 614.593074] xs_sendpages+0x218/0x328
[ 614.604506] xs_tcp_send_request+0xa0/0x1b8
[ 614.617461] xprt_transmit+0xc8/0x4f0
[ 614.628943] call_transmit+0x8c/0xa0
[ 614.640028] __rpc_execute+0xbc/0x6f8
[ 614.651380] rpc_async_schedule+0x28/0x48
[ 614.663846] process_one_work+0x298/0x6a8
[ 614.676299] worker_thread+0x40/0x490
[ 614.687687] kthread+0x134/0x138
[ 614.697804] ret_from_fork+0x10/0x18
[ 614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down
[ 615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
Since tasklets are not really popular anymore anyway, lets convert this
over to a work queue, which can sleep and thus can take the MDIO mutex.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to axienet, the temac driver is now architecture agnostic, and
can be at least compiled for several architectures.
Especially the fact that this is a soft IP for implementing in FPGAs
makes the current restriction rather pointless, as it could literally
appear on any architecture, as long as an FPGA is connected to the bus.
The driver hasn't been actually tried on any hardware, it is just a
drive-by patch when doing the same for axienet (a similar patch for
axienet is already merged).
This (temac and axienet) have been compile-tested for:
alpha hppa64 microblaze mips64 powerpc powerpc64 riscv64 s390 sparc64
(using kernel.org cross compilers).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please note that the delays are calculated based on typical
parameters. But as TEMAC is an HDL IP, designs may vary, and future
work might be needed to make this calculation configurable.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start_p variable was included in the initial commit,
commit 9274498953 ("net: add Xilinx ll_temac device driver"),
but has never had any real use.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_bd_next field was included in the initial commit,
commit 9274498953 ("net: add Xilinx ll_temac device driver"),
but has never had any real use.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the Xilinx AXI ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SDMA engine used by TEMAC halts operation when it has finished
processing of the last buffer descriptor in the buffer ring.
Unfortunately, no interrupt event is generated when this happens,
so we need to setup another mechanism to make sure DMA operation is
restarted when enough buffers have been added to the ring.
Fixes: 9274498953 ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds error handling to the remaining dma_map_single() calls, so that
behavior is well defined if/when we run out of DMA memory.
Fixes: 9274498953 ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in temac_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
This is a port of the similar fix in axienet driver,
commit 7de44285c1 ("net: axienet: Fix race condition causing TX hang").
Fixes: 23ecc4bde2 ("net: ll_temac: fix checksum offload logic")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.
We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
To enable xilinx axi_emac driver support on zynqmp ultrascale platform
(ARCH64) there are two choices, mention ARCH64 as a dependency list
and other is to check if this ARCH dependency list is really needed.
Later approach seems more reasonable, so remove the obsolete ARCH
dependency list for the axi_emac driver.
Sanity test done for microblaze, zynq and zynqmp ultrascale platform.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the DMA memory resource get failed case, the error is not
set and 0 will be returned. Fix it by removing redundant check
since devm_ioremap_resource() will handle it.
Fixes: 28ef9ebdb6 ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "lp->phy_mode" is an enum but in this context GCC treats it as an
unsigned int so the error handling is never triggered.
Fixes: ee06b1728b ("net: axienet: add support for standard phy-mode binding")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible use-after-free issue in the axienet_probe():
1701: np = of_parse_phandle(pdev->dev.of_node, "axistream-connected", 0);
1702: if (np) {
...
1787: of_node_put(np); ---> released here
1788: lp->eth_irq = platform_get_irq(pdev, 0);
1789: } else {
...
1801: }
1802: if (IS_ERR(lp->dma_regs)) {
...
1805: of_node_put(np); ---> double released here
1806: goto free_netdev;
1807: }
We solve this problem by removing the unnecessary of_node_put().
Fixes: 28ef9ebdb6 ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Robert Hancock <hancock@sedsystems.ca>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were accessing the pointer returned from platform_get_resource before
checking if it was valid, causing an oops if it was not. Move this access
after the call to devm_ioremap_resource which does the validity check.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to use the phylink API rather than the legacy PHY
API. This allows for better support for SFP modules connected using a
1000BaseX or SGMII interface.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the axienet driver requires the use of a second devicetree
node, referenced by an axistream-connected attribute on the Ethernet
device node, which contains the resources for the AXI DMA block used by the
device. This setup is problematic for a use case we have where the Ethernet
and DMA cores are behind a PCIe to AXI bridge and the memory resources for
the nodes are injected into the platform devices using the multifunction
device subsystem - it's not easily possible for the driver to obtain the
platform-level resources from the linked device.
In order to simplify that usage model, and simplify the overall use of
this driver in general, allow for all of the resources to be kept on one
node where the resources are retrieved using platform device APIs rather
than device-tree-specific ones. The previous usage setup is still
supported if the axistream-connected attribute is specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was previously using the parent node of the specified PHY
node as the device node to register the MDIO bus on. Andrew Lunn
pointed out this is wrong as the PHY node is potentially not even
underneath the MDIO bus for the current device instance. Find the MDIO
node explicitly by looking it up by name under the controller's device
node instead.
This could potentially break existing device trees if they don't use
"mdio" as the name for the MDIO bus, but I did not find any with various
searches and Xilinx's examples all use mdio as the name so it seems like
this should be relatively safe.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, such as iMX6 with PCIe devices, crashes or hangs can
occur if the axienet device continues to perform DMA transfers after
parent devices/busses have been shut down. Shut down the axienet
interface during its shutdown callback in order to avoid this.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failing initialization on a missing MAC address property is excessive.
We can just fall back to using a random MAC instead, which at least
leaves the interface in a functioning state.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously this driver only handled interrupts from the DMA RX and TX
blocks, not from the Ethernet core itself. Add optional support for
the Ethernet core interrupt, which is used to detect rx_missed and
framing errors signalled by the hardware. In order to use this
interrupt, a third interrupt needs to be specified in the device tree.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Specify IRQF_SHARED to support shared interrupts. If the interrupt
handler is called and the device is not indicating an interrupt,
just return IRQ_NONE rather than spewing error messages.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
These registers are important for troubleshooting the state of the DMA
cores.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Xilinx DMA blocks each have their own reset register, but they both
reset the entire DMA engine, so only one of them needs to be reset.
Also, when stopping the device, we need to not just command the DMA
blocks to stop, but wait for them to stop, and trigger a device reset
to ensure that they are completely stopped.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO clock divisor register setting was only applied on the initial
startup when the driver was loaded. However, this setting is cleared
when the device is reset, such as would occur when the interface was
taken down and brought up again, and so the MDIO bus would be
non-functional afterwards.
Split up the MDIO bus setup and enable into separate functions and
re-enable the bus after a device reset, to ensure that the MDIO
registers are set properly. This also allows us to remove direct access
to MDIO registers in xilinx_axienet_main.c and centralize them all in
xilinx_axienet_mdio.c.
Also, lock the MDIO bus lock around the device reset process, to avoid
MDIO accesses from occurring while the MDIO is disabled during the reset.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the MDIO is is brought up before the netdev is registered, it
should be torn down after the netdev is removed. Otherwise, PHY accesses
can potentially access freed MDIO bus references and cause a crash.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.
Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver should now build on (at least) X86 and ARM platforms, so add
them as supported platforms for the driver in Kconfig.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus for this driver was being named using the result of
of_address_to_resource on a node which may not have any resource on it,
but the return value of that call was not checked so it was using some
random value in the bus name. Change to name the MDIO bus based on the
resource start of the actual Ethernet register block.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was using in_be32 and out_be32 IO accessors which do not
exist on most platforms. Also, the use of big-endian accessors does not
seem correct as this hardware is accessed over an AXI bus which, to the
extent it has an endian-ness, is little-endian. Switch to standard
ioread32/iowrite32 accessors.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was casting skb pointers to u32 and storing them as such in
the DMA buffer descriptor, which is obviously broken on 64-bit. The area
of the buffer descriptor being used is not accessed by the hardware and
has sufficient room for a 32 or 64-bit pointer, so just store the skb
pointer as such.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1b3fa5cf85 ("net: ll_temac: Cleanup multicast filter on change")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast support have been tested and is working now.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid leaving old address table entries when using multicast. If more than
one multicast address were removed, only the first removed address would
actually be cleared.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With .ndo_set_rx_mode/temac_set_multicast_list() being called in atomic
context (holding addr_list_lock), and temac_set_multicast_list() needing
to access temac indirect registers, the mutex used to synchronize indirect
register is a no-no.
Replace it with a spinlock, and avoid sleeping in
temac_indirect_busywait().
To avoid excessive holding of the lock, which is now a spinlock, the
temac_device_reset() function is changed to only hold the lock for short
periods. With timeouts, it could be holding the spinlock for more than
2 seconds.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user has requested IFF_ALLMULTI or have set more than 4 multicast
addresses, we should just use promiscuous mode, but not set it in flags,
as it causes the interface to stay in promiscuous mode even when the
non-IFF_PROMISC condition that caused promiscuous mode to be enabled
has gone away.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On loaded systems with a preemptible kernel the mdio_wait() function may
report an error while everything is working fine:
xemaclite_mdio_wait():
xemaclite_readl() -> chip not ready
--> interrupt here (other work for some time / chip become ready)
if (time_before_eq(end, jiffies))
--> false positive error report
Replace the current code with readx_poll_timeout() which takes care
of the situation.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On loaded systems with a preemptible kernel the mdio_wait() function may
report an error while everything is working fine:
axienet_mdio_wait_until_ready():
axienet_ior() -> chip not ready
--> interrupt here (other work for some time / chip become ready)
if (time_before_eq(end, jiffies))
--> false positive error report
Replace the current code with readx_poll_timeout() which take care
of the situation.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following (similar) warning reported by kbuild test robot:
In function ‘memcpy’,
inlined from ‘smsc75xx_init_mac_address’ at drivers/net/usb/smsc75xx.c:778:3,
inlined from ‘smsc75xx_bind’ at drivers/net/usb/smsc75xx.c:1501:2:
./include/linux/string.h:355:9: warning: argument 2 null where non-null expected [-Wnonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/usb/smsc75xx.c: In function ‘smsc75xx_bind’:
./include/linux/string.h:355:9: note: in a call to built-in function ‘__builtin_memcpy’
I've replaced the offending memcpy with ether_addr_copy, because I'm
100% sure, that of_get_mac_address can't return NULL as it returns valid
pointer or ERR_PTR encoded value, nothing else.
I'm hesitant to just change IS_ERR into IS_ERR_OR_NULL check, as this
would make the warning disappear also, but it would be confusing to
check for impossible return value just to make a compiler happy.
I'm now changing all occurencies of memcpy to ether_addr_copy after the
of_get_mac_address call, as it's very likely, that we're going to get
similar reports from kbuild test robot in the future.
Fixes: a51645f70f ("net: ethernet: support of_get_mac_address new ERR_PTR error")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channel status register value can be very helpful when debugging
SDMA problems.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/xilinx/ll_temac_main.c:66:5: warning: symbol '_temac_ior_be' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:71:6: warning: symbol '_temac_iow_be' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:76:5: warning: symbol '_temac_ior_le' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:81:6: warning: symbol '_temac_iow_le' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:648:6: warning: symbol 'ptr_to_txbd' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:654:6: warning: symbol 'ptr_from_txbd' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "pdata->mdio_bus_id" is unsigned so this condition is always true.
This patch just removes it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_connect() function doesn't return NULL pointers. It returns
error pointers on error, so I have updated the check.
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: d84aec4215 ("net: ll_temac: Fix support for 64-bit platforms")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as TAILDESCR_PTR is written, DMA transfers might start.
Let's ensure we are ready to receive DMA IRQ's before doing that.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows custom setup of IRQ coalescing for platforms using legacy
platform_device. The irq timeout and count parameters can be used for
tuning cpu load vs. latency.
I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as
unused in the documentation I have available. It does not make any
difference in the hardware I have available, so it is left in to not risk
breaking other platforms where it might be used.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usleep_range() to avoid problems with msleep() actually sleeping
much longer than expected.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we are actually using a BD for both the skb and each frag contained in
it, the oldest TX BD would be overwritten when there was exactly one BD
less than needed.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmap the actual buffer length, not the amount of data received, avoiding
resource exhaustion of swiotlb (seen on x86_64 platform).
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect register access goes through a DCR bus bridge, which
allows only one outstanding transaction. And to make matters
worse, each TEMAC IP block contains two Ethernet interfaces, and
although they seem to have separate registers for indirect access,
they actually share the registers. Or to be more specific, MSW, LSW
and CTL registers are physically shared between Ethernet interfaces
in same TEMAC IP, with RDY register being (almost) specificic to
the Ethernet interface. The 0x10000 bit in RDY reflects combined
bus ready state though.
So we need to take care to synchronize not only within a single
device, but also between devices in same TEMAC IP.
This commit allows to do that with legacy platform devices.
For OF devices, the xlnx,compound parent of the temac node should be
used to find siblings, and setup a shared indirect_mutex between them.
I will leave this work to somebody else, as I don't have hardware to
test that. No regression is introduced by that, as before this commit
using two Ethernet interfaces in same TEMAC block is simply broken.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With little-endian and 64-bit support in place, the ll_temac driver can
now be used on x86 and x86_64 platforms.
And while at it, enable COMPILE_TEST also.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both TEMAC and SDMA is big-endian, so make sure that all values in SDMA
buffer descriptors (cmdac_bd) are handled as big-endian, independent of the
host endianness. With all currently supported platforms being big-endian,
this change does not make a change for any of them.
Note, when using app3 and app4 for piggybacking skb pointers there is no
need to care about endianness, as neither TEMAC nor SDMA access app3 and
app4 in TX buffer descriptors.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the powerpc specific MMIO register access functions with the
generic big-endian mmio access functions, and add support for
little-endian access depending on configuration.
Big-endian access is maintained as the default, but little-endian can
be configured in device-tree binding or in platform data.
The temac_ior()/temac_iow() functions are replaced with macro wrappers
to avoid modifying existing code more than necessary.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of buffer descriptor APP4 field (32-bit) for storing skb pointer
obviously does not work on 64-bit platforms.
As APP3 is also unused, we can use that to store the other half of 64-bit
pointer values.
Contrary to what is hinted at in commit message of commit 15bfe05c8d
("net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit")
there are no other pointers stored in cdmac_bd.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support initialization with platdata, so the driver can be used on
non-device-tree platforms.
For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a side effect, a few error cases are fixed.
If of_iomap() of sdma_regs failed, no error code was returned. Fixed to
return -ENOMEM similar to of_iomap() fail of regs.
If sysfs_create_group() or register_netdev() failed, lp->phy_node was not
released.
Finally, the order in remove function is corrected to be reverse order
of what is done in probe, i.e. calling temac_mdio_teardown() last, so we
unregister the netdev that most likely is using the mdio_bus first.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hook only implements a minimal set of ioctl hooks to be able to access
MII regs by using phytool.
When using this simple MAC controller, it's pretty difficult to do
debugging of the PHY chip without checking MII regs.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This set adds a minimal set of ethtool hooks to the driver, which provide a
decent amount of link information via ethtool.
With this change, running `ethtool ethX` in user-space provides all the
neatly-formatted information about the link (what was negotiated, what is
advertised, etc).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes below checkpatch checks-
CHECK: spaces preferred around that '*' (ctx:VxV)
CHECK: No space is necessary after a cast
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes below checkpatch warnings-
WARNING: Block comments use a trailing */ on a separate line
WARNING: Block comments use * on subsequent lines
WARNING: networking block comments don't use an empty /* line,
use /* Comment
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes below kernel-doc warnings:
Function parameter or member 'maxlen' not described in 'xemaclite_recv_data'
Function parameter or member 'address'not described in 'xemaclite_set_mac_address'
Excess function parameter 'addr' description in 'xemaclite_set_mac_address'
No description found for return value of 'xemaclite_interrupt'
No description found for return value of 'xemaclite_mdio_write'
Function parameter or member 'dev' not described in 'xemaclite_mdio_setup'
Excess function parameter 'ofdev' description in 'xemaclite_mdio_setup'
No description found for return value of 'xemaclite_open'
No description found for return value of 'xemaclite_close'
Excess function parameter 'match' description in 'xemaclite_of_probe'
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove else as it is not required with if doing a return.
It also coalesce the format onto a single line and add the
missing space after the comma. Fixes below checkpatch warning-
WARNING: else is not generally useful after a break or return
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch hardcoded function name with a reference to __func__ making
the code more maintainable. Address below checkpatch warning:
WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_read',
this function's name, in a string
+ "xemaclite_mdio_read(phy_id=%i, reg=%x) == %x\n",
WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_write',
this function's name, in a string
+ "xemaclite_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errors are already reported in xemaclite_mdio_setup so avoid
reporting it again.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused 'has_mdio' flag.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'has_mdio' flag is not used,sequence insmod->rmmod-> insmod
leads to failure as MDIO unregister doesn't happen in .remove().
Fix it by checking MII bus pointer instead.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ensure MDIO bus is not double freed in remove() path
assign lp->mii_bus after MDIO bus registration.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
axienet_open no longer return -ENODEV when PHY cannot be connected to
since commit d7cc3163e0 ("net: axienet: Support phy-less mode of operation")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64-bit (e.g. powerpc64/allmodconfig):
drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit_done':
drivers/net/ethernet/xilinx/ll_temac_main.c:633:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
^
cdmac_bd.app4 is u32, so it is too small to hold a kernel pointer.
Note that several other fields in struct cdmac_bd are also too small to
hold physical addresses on 64-bit platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep supporting proprietary "xlnx,phy-type" attribute and add support for
MII connectivity to the PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random MAC address in order to make
sure ndev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xilinx_emaclite uses __raw_writel and __raw_readl for register
accesses. Those functions do not imply any kind of memory barriers and
they may be reordered.
The driver does not seem to take that into account, though, and the
driver does not satisfy the ordering requirements of the hardware.
For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read()
which try to set MDIO address before initiating the transaction.
I'm seeing system freezes with the driver with GCC 5.4 and current
Linux kernels on Zynq-7000 SoC immediately when trying to use the
interface.
In commit 123c1407af ("net: emaclite: Do not use microblaze and ppc
IO functions") the driver was switched from non-generic
in_be32/out_be32 (memory barriers, big endian) to
__raw_readl/__raw_writel (no memory barriers, native endian), so
apparently the device follows system endianness and the driver was
originally written with the assumption of memory barriers.
Rather than try to hunt for each case of missing barrier, just switch
the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending
on endianness instead.
Tested on little-endian Zynq-7000 ARM SoC FPGA.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: 123c1407af ("net: emaclite: Do not use microblaze and ppc IO
functions")
Signed-off-by: David S. Miller <davem@davemloft.net>
xilinx_emaclite looks at the received data to try to determine the
Ethernet packet length but does not properly clamp it if
proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer
overflow and a panic via skb_panic() as the length exceeds the allocated
skb size.
Fix those cases.
Also add an additional unconditional check with WARN_ON() at the end.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: bb81b2ddfa ("net: add Xilinx emac lite device driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare net_device_ops structure as const as it is only stored in
the netdev_ops field of a net_device structure. This field is of type
const, so net_device_ops structures having same properties can be made
const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct net_device ndev;
@@
ndev.netdev_ops=&i@p
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct net_device_ops i;
File size before:
text data bss dec hex filename
6201 744 0 6945 1b21 ethernet/xilinx/xilinx_emaclite.o
File size after:
text data bss dec hex filename
6745 192 0 6937 1b19 ethernet/xilinx/xilinx_emaclite.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xemaclite_remove_ndev() is a simple wrapper around free_netdev()
checking for NULL before the call. All possible paths calling
it are guaranteed to pass a non-NULL argument, so rather call
free_netdev() directly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making temac_init_mac_address() take a const void* address.
Follows commit b34296a9c0 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.
Follows commit b34296a9c0 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev parameter passed to __axienet_device_reset() is not used inside
the function, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival fix, dev_err messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MIPS based xilfpga platform uses this driver.
Enable it for MIPS
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the address configured in the device tree is invalid, the
driver will fallback to using a random address from the locally
administered range.
Signed-off-by: Daniel Romell <daro@hms.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function of_parse_phandle() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 46aa27df88 ('net: axienet: Use devm_* calls')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_find_device() increments the phy struct device refcount, which
we need to properly balance. Add code to network drivers using this
function to ensure that the struct device refcount is correctly
balanced.
For xgene, looking back in the history, we should be able to use
of_phy_connect() with a zero flags argument for the DT case as this is
how the driver used to operate prior to de7b5b3d79 ("net: eth: xgene:
change APM X-Gene SoC platform ethernet to support ACPI").
This leaves the Cavium Thunder BGX unfixed; fixing this driver is a
complicated task, one which the maintainers need to be involved with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read_u32 to read the "clock-frequency" property instead
of using of_get_property with return value checks.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 46aa27df88 ("net: axienet: Use devm_* calls")
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove sparse warnings:
drivers/net/ethernet/xilinx/ll_temac_main.c:65:16: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:70:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:127:16: warning: cast
removes address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:137:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:409:3: warning: symbol
'temac_options' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:590:6: warning: symbol
'temac_adjust_link' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA allocates skb->len instead of headlen
which is used for DMA.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use one return statement instead of two to simplify the code.
Both are returning the same value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize names with other drivers.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_* calls
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use devm_* calls
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize names with other drivers
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is rule for network drivers with comments blocks
which is newly checked by checkpatch.pl script.
Let's fix it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed checkpatch.pl errors and warnings.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds proper checks to handle the PHY-less case.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation, jumbo frames are supported only
for the frame sizes > 16K. This patch corrects this logic to
handle jumbo frames for lesser frame sizes (< 16K) ensuring jumbo frame
MTU is within the limit of max frame size configured in the h/w
design.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet completion interrupts for TX and RX should be serviced before
the packets are consumed. This ensures against the degenerate case when a
new completion interrupt is raised after the handler has exited but before
the interrupts are cleared. In this case its possible for the ISR to clear
an unhandled interrupt (leading to potential deadlock).
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AXI-DMA rx-delay interrupt can sometimes be triggered
when there are 0 outstanding packets received. This is due
to the fact that the receive function will greedily consume
as many packets as possible on interrupt. So if two packets
(with a very particular timing) arrive in succession they
will each cause the rx-delay interrupt, but the first interrupt
will consume both packets.
This means the second interrupt is a 0 packet receive.
This is mostly OK, except that the tail pointer register is
updated unconditionally on receive. Currently the tail pointer
is always set to the current bd-ring descriptor under
the assumption that the hardware has moved onto the next
descriptor. What this means for length 0 recv is the current
descriptor that the hardware is potentially yet to use will
be marked as the tail. This causes the hardware to think
its run out of descriptors deadlocking the whole rx path.
Fixed by updating the tail pointer to the most recent
successfully consumed descriptor.
Reported-by: Wendy Liang <wendy.liang@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the RGMII. The h/w configuration
parameter C_PHY_TYPE, which represents the interface configured in
the design, is used to differentiate various interfaces supported
by AXI Ethernet.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bool constants as the return values instead of 1 and 0.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This property is no longer used in the code yet the code looks for it in the device tree.
It does not cause an error if it's not in the tree.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions kfree() and of_node_put() test whether their argument is NULL
and then return immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling ether_setup is redundant since alloc_etherdev calls it.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
calling ether_setup is redundant since alloc_etherdev calls
it.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
