txgbe register clk which name is i2c_designware.pci_dev_id(),
clk_name will be stored in clk_lookup_alloc. If PCIe bus number
is larger than 0x39, clk_name size will be larger than 20 bytes.
It exceeds clk_lookup_alloc MAX_DEV_ID limits. So the driver
shortened clk_name.
Fixes: b63f20485e ("net: txgbe: Register fixed rate clock")
Signed-off-by: Duanqiang Wen <duanqiangwen@net-swift.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20240313080634.459523-1-duanqiangwen@net-swift.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
GPIO EOI is not set to clear interrupt status after handling the
interrupt. It should be done in irq_chip->irq_ack, but this function
is not called in handle_nested_irq(). So executing function
txgbe_gpio_irq_ack() manually in txgbe_gpio_irq_handler().
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20240301092956.18544-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The register of GPIO interrupt status is masked before MAC IRQ
is enabled. This is because of hardware deficiency. So manually
clear the interrupt status before using them. Otherwise, GPIO
interrupts will never be reported again. There is a workaround for
clearing interrupts to set GPIO EOI in txgbe_up_complete().
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20240301092956.18544-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the current interrupt controller, the MAC interrupt acts as the
parent interrupt in the GPIO IRQ chip. But when the number of Rx/Tx
ring changes, the PCI IRQ vector needs to be reallocated. Then this
interrupt controller would be corrupted. So use irq_domain structure
to avoid the above problem.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to change the interrupt response structure, there will be a
lot of code added next. Move these interrupt codes to a new file, to
make the codes cleaner.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get and set msglevel for driver txgbe and ngbe.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get RX/TX queue number with ethtool -l, and set RX/TX
queue number with ethtool -L. Since interrupts need to be rescheduled,
adjust the allocation of msix enties.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support to show RX/TX coalesce with ethtool -c and set RX/TX
coalesce with ethtool -C.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support to query RX/TX depth with ethtool -g, and change RX/TX depth
with ethtool -G.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to set pause params with ethtool -A and get pause
params with ethtool -a, for ethernet driver txgbe and ngbe.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert txgbe to use phylink and phylink_config added in libwx.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
in some bonding mode, service need to change mac when
netif is running. Wangxun netdev add IFF_LIVE_ADDR_CHANGE
priv_flag to support it.
Signed-off-by: duanqiangwen <duanqiangwen@net-swift.com>
Link: https://lore.kernel.org/r/20231206095044.17844-1-duanqiangwen@net-swift.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the device uses a custom subsystem vendor ID, the function
wx_sw_init() returns before the memory of 'wx->mac_table' is allocated.
The null pointer will causes the kernel panic.
Fixes: 79625f45ca ("net: wangxun: Move MAC address handling to libwx")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since PBA info can be read from lspci, delete txgbe_read_pba_string()
and the prints. In addition, delete the redundant MAC address printing.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231017100635.154967-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wangxun SP chip supports to connect with external PHY (marvell 88x3310),
which links to 10GBASE-T/1000BASE-T/100BASE-T. Add the identification of
media types from subsystem device IDs. For sp_media_copper, register mdio
bus for the external PHY.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable data path before PCS VR reset while switching PCS mode, to prevent
the blocking of data path. Enable AN interrupt for CL37 auto-negotiation.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since XPCS device identifier is implemented in the firmware version
0x20010 and above, so add a warning to prompt the users to upgrade the
firmware to make sure the driver works.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core API pci_dev_id() can be used to get the BDF number for a pci
device. We don't need to compose it manually. Use pci_dev_id() to
simplify the code a little bit.
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230808024931.147048-1-wangxiongfeng2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The old way to do LAN reset is sending reset command to firmware. Once
firmware performs reset, it reconfigures what it needs.
In the new firmware versions, veto bit is introduced for NCSI/LLDP to
block PHY domain in LAN reset. At this point, writing register of LAN
reset directly makes the same effect as the old way. And it does not
reset MNG domain, so that veto bit does not change.
Since veto bit was never used, the old firmware is compatible with the
driver before and after this change. The new firmware needs to use with
the driver after this change if it wants to implement the new feature,
otherwise it is the same as the old firmware.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230717021333.94181-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For some device types like TXGBE_ID_XAUI, *checksum computed in
txgbe_calc_eeprom_checksum() is larger than TXGBE_EEPROM_SUM. Remove the
limit on the size of *checksum.
Fixes: 049fe53653 ("net: txgbe: Add operations to interact with firmware")
Fixes: 5e2ea7801f ("net: txgbe: Fix unsigned comparison to zero in txgbe_calc_eeprom_checksum()")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20230711063414.3311-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add phylink support to Wangxun 10Gb Ethernet controller for the 10GBASE-R
interface.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Register MDIO bus for PCS layer to use Synopsys designware XPCS, support
10GBASE-R interface to the controller.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Register SFP platform device to get modules information.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Register the platform device to use Designware I2C bus master driver.
Use regmap to read/write I2C device region from given base offset.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In order for I2C to be able to work in standard mode, register a fixed
rate clock for each I2C device.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Register software nodes for GPIO, I2C, SFP and PHYLINK. Define the
device properties.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
txgbe_shutdown() relies on txgbe_dev_shutdown() to initialise
wake by passing it by reference. However, txgbe_dev_shutdown()
doesn't use this parameter at all.
wake is then passed uninitialised by txgbe_dev_shutdown()
to pci_wake_from_d3().
Resolve this problem by:
* Removing the unused parameter from txgbe_dev_shutdown()
* Removing the uninitialised variable wake from txgbe_dev_shutdown()
* Passing false to pci_wake_from_d3() - this assumes that
although uninitialised wake was in practice false (0).
I'm not sure that this counts as a bug, as I'm not sure that
it manifests in any unwanted behaviour. But in any case, the issue
was introduced by:
3ce7547e5b ("net: txgbe: Add build support for txgbe")
Flagged by Smatch as:
.../txgbe_main.c:486 txgbe_shutdown() error: uninitialized symbol 'wake'.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add features and hw_features that ngbe can support.
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add ngbe and txgbe ndo_change_mtu support.
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiawen Wu <jiawenwu@trustnetic.com>
Cc: Mengyuan Lou <mengyuanlou@net-swift.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the basic ethtool ops get_drvinfo and get_link for ngbe and txgbe.
Ngbe implements get_link_ksettings, nway_reset and set_link_ksettings
for free using phylib code.
The code related to the physical interface is not yet fully implemented
in txgbe using phylink code. So do not implement get_link_ksettings,
nway_reset and set_link_ksettings in txgbe.
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230214091527.69943-1-mengyuanlou@net-swift.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clean Rx and Tx ring interrupts, process packets in the data path.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the configuration of Rx and Tx ring, set Rx flags and implement
ndo_set_rx_mode ops.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine proper interrupt scheme to enable and handle interrupt.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to move the total members in struct adapter to struct wx_hw
to keep the code clean, it's a bad name of 'wx_hw' only for hardware.
Rename 'wx_hw' to 'wx', and rename the pointers at use.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For setting MAC address, both txgbe and ngbe drivers have the same handling
flow with different parameters. Move the same codes to libwx.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove useless structure txgbe_hw to make the codes clear.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The error checks on checksum for a negative error return always fails because
it is unsigned and can never be negative.
Fixes: 049fe53653 ("net: txgbe: Add operations to interact with firmware")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
eeprom_ptrs should be freed before returned.
Fixes: 049fe53653 ("net: txgbe: Add operations to interact with firmware")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add firmware interaction to get EEPROM information.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MAC address related operations, and register netdev.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset and initialize the hardware by configuring the MAC layer.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get PCI config space info, set LAN id and check flash status.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pci_enable_pcie_error_reporting() should be balanced by a corresponding
pci_disable_pcie_error_reporting() call in the error handling path, as
already done in the remove function.
Fixes: 3ce7547e5b ("net: txgbe: Add build support for txgbe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/082003d00be1f05578c9c6434272ceb314609b8e.1659285240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
