Commit e1d9a90a9b ("net: ethernet: rmnet: Support for ingress MAPv5
checksum offload") broke ingress handling for devices where
RMNET_FLAGS_INGRESS_MAP_CKSUMV5 or RMNET_FLAGS_INGRESS_MAP_CKSUMV4 are
not set. Unless either of these flags are set, the MAP header is not
removed. This commit restores the original logic by ensuring that the
MAP header is removed for all MAP packets.
Fixes: e1d9a90a9b ("net: ethernet: rmnet: Support for ingress MAPv5 checksum offload")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns that proto in rmnet_map_v5_checksum_uplink_packet() might be
used uninitialized:
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:283:14: warning:
variable 'proto' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
} else if (skb->protocol == htons(ETH_P_IPV6)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:295:36: note:
uninitialized use occurs here
check = rmnet_map_get_csum_field(proto, trans);
^~~~~
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:283:10: note:
remove the 'if' if its condition is always true
} else if (skb->protocol == htons(ETH_P_IPV6)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:270:11: note:
initialize the variable 'proto' to silence this warning
u8 proto;
^
= '\0'
1 warning generated.
This is technically a false positive because there is an if statement
above this one that checks skb->protocol for not being either
ETH_P_IP{,V6}. However, it is more obvious to sink that into the if
statement as an else branch, which makes the code clearer and fixes the
warning.
At the same time, move the "IS_ENABLED(CONFIG_IPV6)" into the else if
condition so that the else branch of the preprocessor conditional can
be shared, since there is no build failure with CONFIG_IPV6 disabled.
Fixes: b6e5d27e32 ("net: ethernet: rmnet: Add support for MAPv5 egress packets")
Link: https://github.com/ClangBuiltLinux/linux/issues/1390
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for MAPv5 egress packets.
This involves adding the MAPv5 header and setting the csum_valid_required
in the checksum header to request HW compute the checksum.
Corresponding stats are incremented based on whether the checksum is
computed in software or HW.
New stat has been added which represents the count of packets whose
checksum is calculated by the HW.
Signed-off-by: Sharath Chandra Vurukala <sharathv@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for processing of MAPv5 downlink packets.
It involves parsing the Mapv5 packet and checking the csum header
to know whether the hardware has validated the checksum and is
valid or not.
Based on the checksum valid bit the corresponding stats are
incremented and skb->ip_summed is marked either CHECKSUM_UNNECESSARY
or left as CHEKSUM_NONE to let network stack revalidate the checksum
and update the respective snmp stats.
Current MAPV1 header has been modified, the reserved field in the
Mapv1 header is now used for next header indication.
Signed-off-by: Sharath Chandra Vurukala <sharathv@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to identify significant signature issues add a new stat counter,
which increases on bad signature values that causes a sync loss.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a new network key would cause a reset of the QCA7000. Usually
the driver only notice the SPI interrupt and a single signature error.
So avoid the whole re-sync process (possible packet loss, transmit queue
stop and no carrier for at least 1 second) in this case.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to read the signature three times. So bail out
in case the second check failed.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..).
If some error happens in emac_tx_fill_tpd(), the skb will be freed via
dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd().
But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len).
As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len,
thus my patch assigns skb->len to 'len' before the possible free and
use 'len' instead of skb->len later.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the use of C bit-fields in the rmnet_map_ul_csum_header
structure with a single two-byte (big endian) structure member,
and use masks to encode or get values within it. The content of
these fields can be accessed using simple bitwise AND and OR
operations on the (host byte order) value of the new structure
member.
Previously rmnet_map_ipv4_ul_csum_header() would update C bit-field
values in host byte order, then forcibly fix their byte order using
a combination of byte swap operations and types.
Instead, just compute the value that needs to go into the new
structure member and save it with a simple byte-order conversion.
Make similar simplifications in rmnet_map_ipv6_ul_csum_header().
Finally, in rmnet_map_checksum_uplink_packet() a set of assignments
zeroes every field in the upload checksum header. Replace that with
a single memset() operation.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the use of C bit-fields in the rmnet_map_dl_csum_trailer
structure with a single one-byte field, using constant field masks
to encode or get at embedded values.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The actual layout of bits defined in C bit-fields (e.g. int foo : 3)
is implementation-defined. Structures defined in <linux/if_rmnet.h>
address this by specifying all bit-fields twice, to cover two
possible layouts.
I think this pattern is repetitive and noisy, and I find the whole
notion of compiler "bitfield endianness" to be non-intuitive.
Stop using C bit-fields for the command/data flag and the pad length
fields in the rmnet_map structure, and define a single-byte flags
field instead. Define a mask for the single-bit "command" flag,
and another mask for the encoded pad length. The content of both
fields can be accessed using a simple bitwise AND operation.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following macros, defined in "rmnet_map.h", assume a socket
buffer is provided as an argument without any real indication this
is the case.
RMNET_MAP_GET_MUX_ID()
RMNET_MAP_GET_CD_BIT()
RMNET_MAP_GET_PAD()
RMNET_MAP_GET_CMD_START()
RMNET_MAP_GET_LENGTH()
What they hide is pretty trivial accessing of fields in a structure,
and it's much clearer to see this if we do these accesses directly.
So rather than using these accessor macros, assign a local
variable of the map header pointer type to the socket buffer data
pointer, and derereference that pointer variable.
In "rmnet_map_data.c", use sizeof(object) rather than sizeof(type)
in one spot. Also, there's no need to byte swap 0; it's all zeros
irrespective of endianness.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rmnet_map_ipv4_ul_csum_header() and rmnet_map_ipv6_ul_csum_header()
the offset within a packet at which checksumming should commence is
calculated. This calculation involves byte swapping and a forced type
conversion that makes it hard to understand.
Simplify this by computing the offset in host byte order, then
converting the result when assigning it into the header field.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no guarantee that rmnet rx_handler is only fed with linear
skbs, but current rmnet implementation does not check that, leading
to crash in case of non linear skbs processed as linear ones.
Fix that by ensuring skb linearization before processing.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Link: https://lore.kernel.org/r/1612428002-12333-2-git-send-email-loic.poulain@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packets sent by rmnet to the real device have variable MAP header
lengths based on the data format configured. This patch adds checks
to ensure that the real device MTU is sufficient to transmit the MAP
packet comprising of the MAP header and the IP packet. This check
is enforced when rmnet devices are created and updated and during
MTU updates of both the rmnet and real device.
Additionally, rmnet devices now have a default MTU configured which
accounts for the real device MTU and the headroom based on the data
format.
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Tested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During rmnet unregistration, the real device rx_handler is first cleared
followed by the removal of rx_handler_data after the rcu synchronization.
Any packets in the receive path may observe that the rx_handler is NULL.
However, there is no check when dereferencing this value to use the
rmnet_port information.
This fixes following splat by adding the NULL check.
Unable to handle kernel NULL pointer dereference at virtual
address 000000000000000d
pc : rmnet_rx_handler+0x124/0x284
lr : rmnet_rx_handler+0x124/0x284
rmnet_rx_handler+0x124/0x284
__netif_receive_skb_core+0x758/0xd74
__netif_receive_skb+0x50/0x17c
process_backlog+0x15c/0x1b8
napi_poll+0x88/0x284
net_rx_action+0xbc/0x23c
__do_softirq+0x20c/0x48c
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Link: https://lore.kernel.org/r/1605298325-3705-1-git-send-email-subashab@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only usage of qca_serdev_ops is to pass its address to
serdev_device_set_client_ops() which takes a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the missing clk_disable_unprepare() before return
from emac_clks_phase1_init() in the error handling case.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmnet can have only two bridge interface.
One of them is a link interface and another one is added by
the master operation.
rmnet interface shouldn't allow adding additional
bridge interfaces by mater operation.
But, there is no code to deny additional interfaces.
So, interface leak occurs.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link set dummy1 master rmnet0
ip link set dummy2 master rmnet0
ip link del rmnet0
In the above test command, the dummy0 was attached to rmnet as VND mode.
Then, dummy1 was attached to rmnet0 as BRIDGE mode.
At this point, dummy0 mode is switched from VND to BRIDGE automatically.
Then, dummy2 is attached to rmnet as BRIDGE mode.
At this point, rmnet0 should deny this operation.
But, rmnet0 doesn't deny this.
So that below splat occurs when the rmnet0 interface is deleted.
Splat looks like:
[ 186.684787][ C2] WARNING: CPU: 2 PID: 1009 at net/core/dev.c:8992 rollback_registered_many+0x986/0xcf0
[ 186.684788][ C2] Modules linked in: rmnet dummy openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_x
[ 186.684805][ C2] CPU: 2 PID: 1009 Comm: ip Not tainted 5.8.0-rc1+ #621
[ 186.684807][ C2] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 186.684808][ C2] RIP: 0010:rollback_registered_many+0x986/0xcf0
[ 186.684811][ C2] Code: 41 8b 4e cc 45 31 c0 31 d2 4c 89 ee 48 89 df e8 e0 47 ff ff 85 c0 0f 84 cd fc ff ff 5
[ 186.684812][ C2] RSP: 0018:ffff8880cd9472e0 EFLAGS: 00010287
[ 186.684815][ C2] RAX: ffff8880cc56da58 RBX: ffff8880ab21c000 RCX: ffffffff9329d323
[ 186.684816][ C2] RDX: 1ffffffff2be6410 RSI: 0000000000000008 RDI: ffffffff95f32080
[ 186.684818][ C2] RBP: dffffc0000000000 R08: fffffbfff2be6411 R09: fffffbfff2be6411
[ 186.684819][ C2] R10: ffffffff95f32087 R11: 0000000000000001 R12: ffff8880cd947480
[ 186.684820][ C2] R13: ffff8880ab21c0b8 R14: ffff8880cd947400 R15: ffff8880cdf10640
[ 186.684822][ C2] FS: 00007f00843890c0(0000) GS:ffff8880d4e00000(0000) knlGS:0000000000000000
[ 186.684823][ C2] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 186.684825][ C2] CR2: 000055b8ab1077b8 CR3: 00000000ab612006 CR4: 00000000000606e0
[ 186.684826][ C2] Call Trace:
[ 186.684827][ C2] ? lockdep_hardirqs_on_prepare+0x379/0x540
[ 186.684829][ C2] ? netif_set_real_num_tx_queues+0x780/0x780
[ 186.684830][ C2] ? rmnet_unregister_real_device+0x56/0x90 [rmnet]
[ 186.684831][ C2] ? __kasan_slab_free+0x126/0x150
[ 186.684832][ C2] ? kfree+0xdc/0x320
[ 186.684834][ C2] ? rmnet_unregister_real_device+0x56/0x90 [rmnet]
[ 186.684835][ C2] unregister_netdevice_many.part.135+0x13/0x1b0
[ 186.684836][ C2] rtnl_delete_link+0xbc/0x100
[ ... ]
[ 238.440071][ T1009] unregister_netdevice: waiting for rmnet0 to become free. Usage count = 1
Fixes: 037f9cdf72 ("net: rmnet: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the changelink operation to succeed if the mux_id was
specified as an argument. Note that the mux_id must match the
existing mux_id of the rmnet device or should be an unused mux_id.
Fixes: 1dc49e9d16 ("net: rmnet: do not allow to change mux id if mux id is duplicated")
Reported-and-tested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rmnet_vnd_setup(), which is the callback of ->ndo_start_xmit() is
allowed to call concurrently because it uses RCU protected data.
So, it doesn't need tx lock.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, rmnet_register_real_device() and rmnet_newlink()
are using GFP_ATOMIC.
But, these functions are allowed to sleep.
So, GFP_KERNEL can be used.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rmnet netlink command fails, it doesn't print any error message.
So, users couldn't know the exact reason.
In order to tell the exact reason to the user, the extack error message
is used in this patch.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current rmnet code, there is no module alias.
So, RTNL couldn't load rmnet module automatically.
Test commands:
ip link add dummy0 type dummy
modprobe -rv rmnet
ip link add rmnet0 link dummy0 type rmnet mux_id 1
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet forwarding is not working in rmnet bridge mode.
Because when a packet is forwarded, skb_push() for an ethernet header
is needed. But it doesn't call skb_push().
So, the ethernet header will be lost.
Test commands:
modprobe rmnet
ip netns add nst
ip netns add nst2
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst2
ip link add rmnet0 link veth0 type rmnet mux_id 1
ip link set veth2 master rmnet0
ip link set veth0 up
ip link set veth2 up
ip link set rmnet0 up
ip a a 192.168.100.1/24 dev rmnet0
ip netns exec nst ip link set veth1 up
ip netns exec nst ip a a 192.168.100.2/24 dev veth1
ip netns exec nst2 ip link set veth3 up
ip netns exec nst2 ip a a 192.168.100.3/24 dev veth3
ip netns exec nst2 ping 192.168.100.2
Fixes: 60d58f971c ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to attach a bridge interface to the rmnet interface,
"master" operation is used.
(e.g. ip link set dummy1 master rmnet0)
But, in the rmnet_add_bridge(), which is a callback of ->ndo_add_slave()
doesn't register lower interface.
So, ->ndo_del_slave() doesn't work.
There are other problems too.
1. It couldn't detect circular upper/lower interface relationship.
2. It couldn't prevent stack overflow because of too deep depth
of upper/lower interface
3. It doesn't check the number of lower interfaces.
4. Panics because of several reasons.
The root problem of these issues is actually the same.
So, in this patch, these all problems will be fixed.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link add dummy1 master rmnet0 type dummy
ip link add dummy2 master rmnet0 type dummy
ip link del rmnet0
ip link del dummy2
ip link del dummy1
Splat looks like:
[ 41.867595][ T1164] general protection fault, probably for non-canonical address 0xdffffc0000000101I
[ 41.869993][ T1164] KASAN: null-ptr-deref in range [0x0000000000000808-0x000000000000080f]
[ 41.872950][ T1164] CPU: 0 PID: 1164 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 41.873915][ T1164] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 41.875161][ T1164] RIP: 0010:rmnet_unregister_bridge.isra.6+0x71/0xf0 [rmnet]
[ 41.876178][ T1164] Code: 48 89 ef 48 89 c6 5b 5d e9 fc fe ff ff e8 f7 f3 ff ff 48 8d b8 08 08 00 00 48 ba 00 7
[ 41.878925][ T1164] RSP: 0018:ffff8880c4d0f188 EFLAGS: 00010202
[ 41.879774][ T1164] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000101
[ 41.887689][ T1164] RDX: dffffc0000000000 RSI: ffffffffb8cf64f0 RDI: 0000000000000808
[ 41.888727][ T1164] RBP: ffff8880c40e4000 R08: ffffed101b3c0e3c R09: 0000000000000001
[ 41.889749][ T1164] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 1ffff110189a1e3c
[ 41.890783][ T1164] R13: ffff8880c4d0f200 R14: ffffffffb8d56160 R15: ffff8880ccc2c000
[ 41.891794][ T1164] FS: 00007f4300edc0c0(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 41.892953][ T1164] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 41.893800][ T1164] CR2: 00007f43003bc8c0 CR3: 00000000ca53e001 CR4: 00000000000606f0
[ 41.894824][ T1164] Call Trace:
[ 41.895274][ T1164] ? rcu_is_watching+0x2c/0x80
[ 41.895895][ T1164] rmnet_config_notify_cb+0x1f7/0x590 [rmnet]
[ 41.896687][ T1164] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 41.897611][ T1164] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 41.898508][ T1164] ? __module_text_address+0x13/0x140
[ 41.899162][ T1164] notifier_call_chain+0x90/0x160
[ 41.899814][ T1164] rollback_registered_many+0x660/0xcf0
[ 41.900544][ T1164] ? netif_set_real_num_tx_queues+0x780/0x780
[ 41.901316][ T1164] ? __lock_acquire+0xdfe/0x3de0
[ 41.901958][ T1164] ? memset+0x1f/0x40
[ 41.902468][ T1164] ? __nla_validate_parse+0x98/0x1ab0
[ 41.903166][ T1164] unregister_netdevice_many.part.133+0x13/0x1b0
[ 41.903988][ T1164] rtnl_delete_link+0xbc/0x100
[ ... ]
Fixes: 60d58f971c ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically, duplicate mux id isn't be allowed.
So, the creation of rmnet will be failed if there is duplicate mux id
is existing.
But, changelink routine doesn't check duplicate mux id.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link add rmnet1 link dummy0 type rmnet mux_id 2
ip link set rmnet1 type rmnet mux_id 1
Fixes: 23790ef120 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmnet_get_port() internally calls rcu_dereference_rtnl(),
which checks RTNL.
But rmnet_get_port() could be called by packet path.
The packet path is not protected by RTNL.
So, the suspicious RCU usage problem occurs.
Test commands:
modprobe rmnet
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link set veth1 netns nst
ip link add rmnet0 link veth0 type rmnet mux_id 1
ip netns exec nst ip link add rmnet1 link veth1 type rmnet mux_id 1
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set rmnet1 up
ip netns exec nst ip a a 192.168.100.2/24 dev rmnet1
ip link set veth0 up
ip link set rmnet0 up
ip a a 192.168.100.1/24 dev rmnet0
ping 192.168.100.2
Splat looks like:
[ 146.630958][ T1174] WARNING: suspicious RCU usage
[ 146.631735][ T1174] 5.6.0-rc1+ #447 Not tainted
[ 146.632387][ T1174] -----------------------------
[ 146.633151][ T1174] drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c:386 suspicious rcu_dereference_check() !
[ 146.634742][ T1174]
[ 146.634742][ T1174] other info that might help us debug this:
[ 146.634742][ T1174]
[ 146.645992][ T1174]
[ 146.645992][ T1174] rcu_scheduler_active = 2, debug_locks = 1
[ 146.646937][ T1174] 5 locks held by ping/1174:
[ 146.647609][ T1174] #0: ffff8880c31dea70 (sk_lock-AF_INET){+.+.}, at: raw_sendmsg+0xab8/0x2980
[ 146.662463][ T1174] #1: ffffffff93925660 (rcu_read_lock_bh){....}, at: ip_finish_output2+0x243/0x2150
[ 146.671696][ T1174] #2: ffffffff93925660 (rcu_read_lock_bh){....}, at: __dev_queue_xmit+0x213/0x2940
[ 146.673064][ T1174] #3: ffff8880c19ecd58 (&dev->qdisc_running_key#7){+...}, at: ip_finish_output2+0x714/0x2150
[ 146.690358][ T1174] #4: ffff8880c5796898 (&dev->qdisc_xmit_lock_key#3){+.-.}, at: sch_direct_xmit+0x1e2/0x1020
[ 146.699875][ T1174]
[ 146.699875][ T1174] stack backtrace:
[ 146.701091][ T1174] CPU: 0 PID: 1174 Comm: ping Not tainted 5.6.0-rc1+ #447
[ 146.705215][ T1174] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 146.706565][ T1174] Call Trace:
[ 146.707102][ T1174] dump_stack+0x96/0xdb
[ 146.708007][ T1174] rmnet_get_port.part.9+0x76/0x80 [rmnet]
[ 146.709233][ T1174] rmnet_egress_handler+0x107/0x420 [rmnet]
[ 146.710492][ T1174] ? sch_direct_xmit+0x1e2/0x1020
[ 146.716193][ T1174] rmnet_vnd_start_xmit+0x3d/0xa0 [rmnet]
[ 146.717012][ T1174] dev_hard_start_xmit+0x160/0x740
[ 146.717854][ T1174] sch_direct_xmit+0x265/0x1020
[ 146.718577][ T1174] ? register_lock_class+0x14d0/0x14d0
[ 146.719429][ T1174] ? dev_watchdog+0xac0/0xac0
[ 146.723738][ T1174] ? __dev_queue_xmit+0x15fd/0x2940
[ 146.724469][ T1174] ? lock_acquire+0x164/0x3b0
[ 146.725172][ T1174] __dev_queue_xmit+0x20c7/0x2940
[ ... ]
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The reset counter is specific for every QCA700x chip. So move this
into the private driver struct. Otherwise we get unpredictable reset
behavior in setups with multiple QCA700x chips.
Fixes: 291ab06ecf (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving many or larger packets, e.g. when doing a file download,
it was observed that the read buffer size register reports up to 4 bytes
more than the current define allows in the check.
If this is the case, then no data transfer is initiated to receive the
packets (and thus to empty the buffer) which results in a stall of the
interface.
These 4 bytes are a hardware generated frame length which is prepended
to the actual frame, thus we have to respect it during our check.
Fixes: 026b907d58 ("net: qca_spi: Add available buffer space verification")
Signed-off-by: Michael Heimpold <michael.heimpold@in-tech.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the MTU can be a frequent operation and it is already clear
when (or not) a MTU change is successful, demote prints to debug prints.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the exit/unregistration process of the RmNet driver, the function
rmnet_unregister_real_device() is called to handle freeing the driver's
internal state and removing the RX handler on the underlying physical
device. However, the order of operations this function performs is wrong
and can lead to a use after free of the rmnet_port structure.
Before calling netdev_rx_handler_unregister(), this port structure is
freed with kfree(). If packets are received on any RmNet devices before
synchronize_net() completes, they will attempt to use this already-freed
port structure when processing the packet. As such, before cleaning up any
other internal state, the RX handler must be unregistered in order to
guarantee that no further packets will arrive on the device.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Yangtao Li <tiny.windzz@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The udp_ip4_ind bit is set only for IPv4 UDP non-fragmented packets
so that the hardware can flip the checksum to 0xFFFF if the computed
checksum is 0 per RFC768.
However, this bit had to be set for IPv6 UDP non fragmented packets
as well per hardware requirements. Otherwise, IPv6 UDP packets
with computed checksum as 0 were transmitted by hardware and were
dropped in the network.
In addition to setting this bit for IPv6 UDP, the field is also
appropriately renamed to udp_ind as part of this change.
Fixes: 5eb5f8608e ("net: qualcomm: rmnet: Add support for TX checksum offload")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create if_rmnet.h and move the rmnet MAP packet structs to this
common include file. To account for portablity, add little and
big endian bitfield definitions similar to the ip & tcp headers.
The definitions in the headers can now be re-used by the
upcoming ipa driver series as well as qmi_wwan.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in emac_mac_tx_process() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c: In function 'rmnet_map_do_flow_control':
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:23:36: warning:
variable 'cmd' set but not used [-Wunused-but-set-variable]
struct rmnet_map_control_command *cmd;
'cmd' not used anymore now, should also be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:26:6:
warning: variable 'ip_family' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:27:6:
warning: variable 'fc_seq' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:28:6:
warning: variable 'qos_id' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dev is dereferenced by the call dev_net(dev) before dev is null
checked. Fix this by null checking dev before the potential null
pointer dereference.
Detected by CoverityScan, CID#1462955 ("Dereference before null check")
Fixes: 23790ef120 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A null dereference was observed when a sysctl was being set
from userspace and rmnet was stuck trying to complete some actions
in the NETDEV_REGISTER callback. This is because the real_dev is set
only after the device registration handler completes.
sysctl call stack -
<6> Unable to handle kernel NULL pointer dereference at
virtual address 00000108
<2> pc : rmnet_vnd_get_iflink+0x1c/0x28
<2> lr : dev_get_iflink+0x2c/0x40
<2> rmnet_vnd_get_iflink+0x1c/0x28
<2> inet6_fill_ifinfo+0x15c/0x234
<2> inet6_ifinfo_notify+0x68/0xd4
<2> ndisc_ifinfo_sysctl_change+0x1b8/0x234
<2> proc_sys_call_handler+0xac/0x100
<2> proc_sys_write+0x3c/0x4c
<2> __vfs_write+0x54/0x14c
<2> vfs_write+0xcc/0x188
<2> SyS_write+0x60/0xc0
<2> el0_svc_naked+0x34/0x38
device register call stack -
<2> notifier_call_chain+0x84/0xbc
<2> raw_notifier_call_chain+0x38/0x48
<2> call_netdevice_notifiers_info+0x40/0x70
<2> call_netdevice_notifiers+0x38/0x60
<2> register_netdevice+0x29c/0x3d8
<2> rmnet_vnd_newlink+0x68/0xe8
<2> rmnet_newlink+0xa0/0x160
<2> rtnl_newlink+0x57c/0x6c8
<2> rtnetlink_rcv_msg+0x1dc/0x328
<2> netlink_rcv_skb+0xac/0x118
<2> rtnetlink_rcv+0x24/0x30
<2> netlink_unicast+0x158/0x1f0
<2> netlink_sendmsg+0x32c/0x338
<2> sock_sendmsg+0x44/0x60
<2> SyS_sendto+0x150/0x1ac
<2> el0_svc_naked+0x34/0x38
Fixes: b752eff5be ("net: qualcomm: rmnet: Implement ndo_get_iflink")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interferences on the SPI line could distort the response of
available buffer space. So at least we should check that the
response doesn't exceed the maximum available buffer space.
In error case increase a new error counter and retry it later.
This behavior avoids buffer errors in the QCA7000, which
results in an unnecessary chip reset including packet loss.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The incoming skb needs to be reallocated in case the headroom
is not sufficient to adjust the ethernet header. This allocation
needs to be atomic otherwise it results in this splat
[<600601bb>] ___might_sleep+0x185/0x1a3
[<603f6314>] ? _raw_spin_unlock_irqrestore+0x0/0x27
[<60069bb0>] ? __wake_up_common_lock+0x95/0xd1
[<600602b0>] __might_sleep+0xd7/0xe2
[<60065598>] ? enqueue_task_fair+0x112/0x209
[<600eea13>] __kmalloc_track_caller+0x5d/0x124
[<600ee9b6>] ? __kmalloc_track_caller+0x0/0x124
[<602696d5>] __kmalloc_reserve.isra.34+0x30/0x7e
[<603f629b>] ? _raw_spin_lock_irqsave+0x0/0x3d
[<6026b744>] pskb_expand_head+0xbf/0x310
[<6025ca6a>] rmnet_rx_handler+0x7e/0x16b
[<6025c9ec>] ? rmnet_rx_handler+0x0/0x16b
[<6027ad0c>] __netif_receive_skb_core+0x301/0x96f
[<60033c17>] ? set_signals+0x0/0x40
[<6027bbcb>] __netif_receive_skb+0x24/0x8e
Fixes: 74692caf1b ("net: qualcomm: rmnet: Process packets over ethernet")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The incoming skb needs to be reallocated in case the headroom
is not sufficient to add the MAP header. This allocation needs to
be atomic otherwise it results in the following splat
[32805.801456] BUG: sleeping function called from invalid context
[32805.841141] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[32805.904773] task: ffffffd7c5f62280 task.stack: ffffff80464a8000
[32805.910851] pc : ___might_sleep+0x180/0x188
[32805.915143] lr : ___might_sleep+0x180/0x188
[32806.131520] Call trace:
[32806.134041] ___might_sleep+0x180/0x188
[32806.137980] __might_sleep+0x50/0x84
[32806.141653] __kmalloc_track_caller+0x80/0x3bc
[32806.146215] __kmalloc_reserve+0x3c/0x88
[32806.150241] pskb_expand_head+0x74/0x288
[32806.154269] rmnet_egress_handler+0xb0/0x1d8
[32806.162239] rmnet_vnd_start_xmit+0xc8/0x13c
[32806.166627] dev_hard_start_xmit+0x148/0x280
[32806.181181] sch_direct_xmit+0xa4/0x198
[32806.185125] __qdisc_run+0x1f8/0x310
[32806.188803] net_tx_action+0x23c/0x26c
[32806.192655] __do_softirq+0x220/0x408
[32806.196420] do_softirq+0x4c/0x70
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RMNET RX handler was processing invalid packets that were
originally sent on the real device and were looped back via
dev_loopback_xmit(). This was detected using syzkaller.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPI protocol for the QCA7000 doesn't have any fault detection.
In order to increase the drivers reliability in noisy environments,
we could implement a write verification inspired by the enc28j60.
This should avoid situations were the driver wrongly assumes the
receive interrupt is enabled and miss all incoming packets.
This function is disabled per default and can be controlled via module
parameter wr_verify.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With performance optimization the spi transfer and messages of basic
register operations like qcaspi_read_register moved into the private
driver structure. But they weren't protected against mutual access
(e.g. between driver kthread and ethtool). So dumping the QCA7000
registers via ethtool during network traffic could make spi_sync
hang forever, because the completion in spi_message is overwritten.
So revert the optimization completely.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA700")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cases the probing fails the log level of the messages should
be an error.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the SPI thread is not running, a simple reset of sync
state won't fix the transmit timeout. We also need to wake up the kernel
thread.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: ed7d42e24e ("net: qca_spi: fix transmit queue timeout handling")
Signed-off-by: David S. Miller <davem@davemloft.net>
As long as the synchronization with the QCA7000 isn't finished, we
cannot accept packets from the upper layers. So let the SPI thread
enable the TX queue after sync and avoid unwanted packet drop.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1
Convert the uses of random_ether_addr to enable removing the #define
Miscellanea:
o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing of_node_put() call for device node returned by
of_parse_phandle().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending an ack to a command packet, the skb is still referenced
after it is sent to the real device. Since the real device could
free the skb, the device pointer would be invalid.
Also, remove an unnecessary variable.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RAWIP devices such as rmnet do not have a hardware address and
instead require the kernel to generate a random IID for the
IPv6 addresses.
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "net: qcom/emac: Encapsulate sgmii ops under one structure"
introduced the sgmii_ops structure, but did not correctly initialize
it on device tree platforms. This resulted in compiler warnings when
ACPI is not enabled.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use non-NUMA aware allocation for TPD and RRD buffers,
this patch modifies to use NUMA friendly allocation.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces ops structure for sgmii, This by ensures that
we do not need dummy functions in case of emulation platforms.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The command packet size is already checked once in
rmnet_map_deaggregate() for the header, packet and trailer size, so
this additional check is not needed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool private stats handler to debug the handling of packets
with checksum offload header / trailer. This allows to keep track of
the number of packets for which hardware computes the checksum and
counts and reasons where checksum computation was skipped in hardware
and was done in the network stack.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets in transmit path could potentially be dropped if there were
errors while adding the MAP header or the checksum header.
Increment the tx_drops stats in these cases.
Additionally, refactor the code to free the packet and increment
the tx_drops stat under a single label.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last rmnet device attached to a real device is removed, the
real device is unregistered from rmnet. As a result, the real device
lookup fails resulting in a warning when the fill_info handler is
called as part of the rmnet device unregistration.
Fix this by returning the rmnet flags as 0 when no real device is
present.
WARNING: CPU: 0 PID: 1779 at net/core/rtnetlink.c:3254
rtmsg_ifinfo_build_skb+0xca/0x10d
Modules linked in:
CPU: 0 PID: 1779 Comm: ip Not tainted 4.16.0-11872-g7ce2367 #1
Stack:
7fe655f0 60371ea3 00000000 00000000
60282bc6 6006b116 7fe65600 60371ee8
7fe65660 6003a68c 00000000 900000000
Call Trace:
[<6006b116>] ? printk+0x0/0x94
[<6001f375>] show_stack+0xfe/0x158
[<60371ea3>] ? dump_stack_print_info+0xe8/0xf1
[<60282bc6>] ? rtmsg_ifinfo_build_skb+0xca/0x10d
[<6006b116>] ? printk+0x0/0x94
[<60371ee8>] dump_stack+0x2a/0x2c
[<6003a68c>] __warn+0x10e/0x13e
[<6003a82c>] warn_slowpath_null+0x48/0x4f
[<60282bc6>] rtmsg_ifinfo_build_skb+0xca/0x10d
[<60282c4d>] rtmsg_ifinfo_event.part.37+0x1e/0x43
[<60282c2f>] ? rtmsg_ifinfo_event.part.37+0x0/0x43
[<60282d03>] rtmsg_ifinfo+0x24/0x28
[<60264e86>] dev_close_many+0xba/0x119
[<60282cdf>] ? rtmsg_ifinfo+0x0/0x28
[<6027c225>] ? rtnl_is_locked+0x0/0x1c
[<6026ca67>] rollback_registered_many+0x1ae/0x4ae
[<600314be>] ? unblock_signals+0x0/0xae
[<6026cdc0>] ? unregister_netdevice_queue+0x19/0xec
[<6026ceec>] unregister_netdevice_many+0x21/0xa1
[<6027c765>] rtnl_delete_link+0x3e/0x4e
[<60280ecb>] rtnl_dellink+0x262/0x29c
[<6027c241>] ? rtnl_get_link+0x0/0x3e
[<6027f867>] rtnetlink_rcv_msg+0x235/0x274
Fixes: be81a85f5f ("net: qualcomm: rmnet: Implement fill_info")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to rmnet_get_endpoint can potentially return NULL so check
for this to avoid any subsequent null pointer dereferences on a NULL
ep.
Detected by CoverityScan, CID#1465385 ("Dereference null return value")
Fixes: 23790ef120 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed to query the mux_id and flags of a rmnet device.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define new netlink attributes for rmnet mux_id and flags. These
flags / mux_id were earlier using vlan flags / id respectively.
The flag bits are also moved to uapi and are renamed with
prefix RMNET_FLAG_*.
Also add the rmnet policy to handle the new netlink attributes.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device of the de-aggregated skb is correctly assigned after inspecting
the mux_id, so remove the assignment in rmnet_map_deaggregate().
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warnings which were reported when running with sparse
(make C=1 CF=-D__CHECK_ENDIAN__)
drivers/net/ethernet/qualcomm/rmnet/rmnet_handlers.c:81:15:
warning: cast to restricted __be16
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:271:37:
warning: incorrect type in assignment (different base types)
expected unsigned short [unsigned] [usertype] pkt_len
got restricted __be16 [usertype] <noident>
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:287:29:
warning: incorrect type in assignment (different base types)
expected unsigned short [unsigned] [usertype] pkt_len
got restricted __be16 [usertype] <noident>
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:310:22:
warning: cast to restricted __be16
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:319:13:
warning: cast to restricted __be16
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:49:18:
warning: cast to restricted __be16
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:50:18:
warning: cast to restricted __be32
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:74:21:
warning: cast to restricted __be16
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_expand without __GFP_NOWARN already does a dump_stack
on OOM so these messages are redundant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the warning messages/call traces seen if DMA debug is
enabled, In case of fragmented skb's memory was allocated using
dma_map_page but freed using dma_unmap_single. This patch modifies buffer
allocations in TX path to use dma_map_page in all the places and
dma_unmap_page while freeing the buffers.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a command packet with invalid mux id is received, the packet would
not have a valid endpoint. This invalid endpoint maybe dereferenced
leading to a crash. Identified by manual code inspection.
Fixes: 3352e6c457 ("net: qualcomm: rmnet: Convert the muxed endpoint to hlist")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DEBUG_PREEMPT enabled, a crash with the following call
stack was observed when removing a real dev which had rmnet devices
attached to it.
To fix this, remove the netdev_upper link APIs and instead use the
existing information in rmnet_port and rmnet_priv to get the
association between real and rmnet devs.
BUG: sleeping function called from invalid context
in_atomic(): 0, irqs_disabled(): 0, pid: 5762, name: ip
Preemption disabled at:
[<ffffff9d49043564>] debug_object_active_state+0xa4/0x16c
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
PC is at ___might_sleep+0x13c/0x180
LR is at ___might_sleep+0x17c/0x180
[<ffffff9d48ce0924>] ___might_sleep+0x13c/0x180
[<ffffff9d48ce09c0>] __might_sleep+0x58/0x8c
[<ffffff9d49d6253c>] mutex_lock+0x2c/0x48
[<ffffff9d48ed4840>] kernfs_remove_by_name_ns+0x48/0xa8
[<ffffff9d48ed6ec8>] sysfs_remove_link+0x30/0x58
[<ffffff9d49b05840>] __netdev_adjacent_dev_remove+0x14c/0x1e0
[<ffffff9d49b05914>] __netdev_adjacent_dev_unlink_lists+0x40/0x68
[<ffffff9d49b08820>] netdev_upper_dev_unlink+0xb4/0x1fc
[<ffffff9d494a29f0>] rmnet_dev_walk_unreg+0x6c/0xc8
[<ffffff9d49b00b40>] netdev_walk_all_lower_dev_rcu+0x58/0xb4
[<ffffff9d494a30fc>] rmnet_config_notify_cb+0xf4/0x134
[<ffffff9d48cd21b4>] raw_notifier_call_chain+0x58/0x78
[<ffffff9d49b028a4>] call_netdevice_notifiers_info+0x48/0x78
[<ffffff9d49b0b568>] rollback_registered_many+0x230/0x3c8
[<ffffff9d49b0b738>] unregister_netdevice_many+0x38/0x94
[<ffffff9d49b1e110>] rtnl_delete_link+0x58/0x88
[<ffffff9d49b201dc>] rtnl_dellink+0xbc/0x1cc
[<ffffff9d49b2355c>] rtnetlink_rcv_msg+0xb0/0x244
[<ffffff9d49b5230c>] netlink_rcv_skb+0xb4/0xdc
[<ffffff9d49b204f4>] rtnetlink_rcv+0x34/0x44
[<ffffff9d49b51af0>] netlink_unicast+0x1ec/0x294
[<ffffff9d49b51fdc>] netlink_sendmsg+0x320/0x390
[<ffffff9d49ae6858>] sock_sendmsg+0x54/0x60
[<ffffff9d49ae6f94>] ___sys_sendmsg+0x298/0x2b0
[<ffffff9d49ae98f8>] SyS_sendmsg+0xb4/0xf0
[<ffffff9d48c83770>] el0_svc_naked+0x24/0x28
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Fixes: 60d58f971c ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit TPD3[31] is used as a timestamp bit if PTP is enabled, but
it's used as an address bit if PTP is disabled. Since PTP isn't
supported by the driver, we can extend the DMA address to 46 bits.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Real devices may support scatter gather(SG), so enable SG on rmnet
devices to use GSO. GSO reduces CPU cycles by 20% for a rate of
146Mpbs for a single stream TCP connection.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX checksum offload applies to TCP / UDP packets which are not
fragmented using the MAPv4 checksum trailer. The following needs to be
done to have checksum computed in hardware -
1. Set the checksum start offset and inset offset.
2. Set the csum_enabled bit
3. Compute and set 1's complement of partial checksum field in
transport header.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the MAPv4 packet format in conjunction with MAP commands,
a dummy DL checksum trailer will be appended to the packet. Before
this packet is sent out as an ACK, the DL checksum trailer needs to be
removed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the MAPv4 packet format, receive checksum offload can be
enabled in hardware. The checksum computation over pseudo header is
not offloaded but the rest of the checksum computation over
the payload is offloaded. This applies only for TCP / UDP packets
which are not fragmented.
rmnet validates the TCP/UDP checksum for the packet using the checksum
from the checksum trailer added to the packet by hardware. The
validation performed is as following -
1. Perform 1's complement over the checksum value from the trailer
2. Compute 1's complement checksum over IPv4 / IPv6 header and
subtracts it from the value from step 1
3. Computes 1's complement checksum over IPv4 / IPv6 pseudo header and
adds it to the value from step 2
4. Subtracts the checksum value from the TCP / UDP header from the
value from step 3.
5. Compares the value from step 4 to the checksum value from the
TCP / UDP header.
6. If the comparison in step 5 succeeds, CHECKSUM_UNNECESSARY is set
and the packet is passed on to network stack. If there is a
failure, then the packet is passed on as such without modifying
the ip_summed field.
The checksum field is also checked for UDP checksum 0 as per RFC 768
and for unexpected TCP checksum of 0.
If checksum offload is disabled when using MAPv4 packet format in
receive path, the packet is queued as is to network stack without
the validations above.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAPv4 packet format adds support for RX / TX checksum offload.
For a bi-directional UDP stream at a rate of 570 / 146 Mbps, roughly
10% CPU cycles are saved.
For receive path, there is a checksum trailer appended to the end of
the MAP packet. The valid field indicates if hardware has computed
the checksum. csum_start_offset indicates the offset from the start
of the IP header from which hardware has computed checksum.
csum_length is the number of bytes over which the checksum was
computed and the resulting value is csum_value.
In the transmit path, a header is appended between the end of the MAP
header and the start of the IP packet. csum_start_offset is the offset
in bytes from which hardware will compute the checksum if the
csum_enabled bit is set. udp_ip4_ind indicates if the checksum
value of 0 is valid or not. csum_insert_offset is the offset from the
csum_start_offset where hardware will insert the computed checksum.
The use of this additional packet format for checksum offload is
explained in subsequent patches.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The real device over which the rmnet devices are installed also
aggregate multiple IP packets and sends them as a single large
aggregate frame to the hardware. This causes degraded throughput
for TCP TX due to bufferbloat.
To overcome this problem, pacing shift value of 8 is set using the
sk_pacing_shift_update() helper. This value was determined based
on experiments with a single stream TCP TX using iperf for a
duration of 30s.
Pacing shift | Observed data rate (Mbps)
10 | 9
9 | 140
8 | 146 (Max link rate)
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done so that we can use this field for both ingress and
egress flags.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmnet_map_demultiplex() is only declared but not defined anywhere,
so remove it.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmnet devices cannot have a mux id of 255. This is validated when
assigning the mux id to the rmnet devices. As a result, checking for
mux id 255 does not apply in egress path.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already check the headroom once in rmnet_map_egress_handler(),
so this is not needed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the order of mac_up and sgmii_open for the
reasons noted below:
- If open takes more time(if the SGMII block is not responding or
if we want to do some delay based task) in this situation we
will hit NETDEV watchdog
- The main reason : We should signal to upper layers that we are
ready to receive packets "only" when the entire path is initialized
not the other way around, this is followed in the reset path where
we do mac_down, sgmii_reset and mac_up. This also makes the driver
uniform across the reset and open paths.
- In the future there may be need for delay based tasks to be done in
sgmii open which will result in NETDEV watchdog
- As per the documentation the order of init should be sgmii, mac, rings
and DMA
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mdio read/write takes around ~115us as the timeout
between status check is set to 100us.
By reducing the timeout to 1us mdio read/write takes ~15us to
complete. This improves the link up event response.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option to configure the mux id, aggregation and commad feature
for existing rmnet devices. Implement the changelink netlink
operation for this.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option to configure the rmnet aggregation and command features
on device creation. This is achieved by using the vlan flags option.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to send and receive packets over ethernet.
An example of usage is testing the data path on UML. This can be
achieved by setting up two UML instances in multicast mode and
associating rmnet over the UML ethernet device.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon de-multiplexing data from one real dev, the packets can be sent
to an unique rmnet device for a given mux id.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiplexing is always enabled when transmiting from a rmnet device,
so remove the redundant egress macros. De-multiplexing is always
enabled when receiving packets from a rmnet device, so remove those
ingress macros.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the success and consumed entries were actually in use.
Use standard error codes instead.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the rmnet device creation fails in the newlink either while
registering with the physical device or after subsequent
operations, the rmnet endpoint information is never freed.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a skb in transmit path does not have sufficient headroom to add
the map header, the skb is not sent out and is never freed.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add gro_cells so that rmnet devices can call gro_cells_receive
instead of netif_receive_skb.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement 64 bit per cpu stats.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rmnet device needs to assigned for all packets in the
deaggregation path based on the mux id, so the check is not needed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since packet is always consumed by rmnet_rx_handler(), we always
return RX_HANDLER_CONSUMED. There is no need to pass on this
value through multiple functions.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit df1ec1b9d0.
It turns out that memory allocated via dma_alloc_coherent is always
aligned to the size of the buffer, so there's no way the RRD and RFD
can ever be in separate 32-bit regions.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to bridge two devices which can send multiplexing and
aggregation (MAP) data. This is done only when the data itself is
not going to be consumed in the stack but is being passed on to a
different endpoint. This is mainly used for testing.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using a static array, use a hlist to store the muxed
endpoints and use the mux id to query the rmnet_device.
This is useful as usually very few mux ids are used.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rmnet_devices information is already stored in muxed_ep, so
storing this in rmnet_devices[] again is redundant.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The end point is set twice in the local_ep as well as the mux_id and
the real_dev in the rmnet private structure. Remove the local_ep.
While these elements are equivalent, rmnet_endpoint will be
used only as part of the rmnet_port for muxed scenarios in VND mode.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mode information on the real device makes it easier to route packets
to rmnet device or bridged device based on the configuration.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of these constants were used in the initial patchset where
custom netlink configuration was used and hence are no longer relevant.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be rewritten in the following patches.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the error messages that are printed by the interrupt handlers
are poorly written. For example, many don't include a device prefix,
so there's no indication that they are EMAC errors.
Also use rate limiting for all messages that could be printed from
interrupt context.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC has a restriction that the upper 32 bits of the base addresses
for the RFD and RRD rings must be the same. The ensure that restriction,
we allocate twice the space for the RRD and locate it at an appropriate
address.
We also re-arrange the allocations so that invalid addresses are even
less likely.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC is capable of multiple TX and RX rings, but the driver only
supports one ring for each. One function had some left-over unused
code that supports multiple rings, but all it did was make the code
harder to read.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 64/32-bit DMA mask hackery in the EMAC driver is not actually necessary,
and is technically not accurate. The EMAC hardware is limted to a 45-bit
DMA address. Although no EMAC-enabled system can have that much DDR,
an IOMMU could possible provide a larger address. Rather than play games
with the DMA mappings, the driver should provide a correct value and
trust the DMA/IOMMU layers to do the right thing.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function emac_isr is local to the source and does not need to
be in global scope, so make it static.
Cleans up sparse warnings:
symbol 'emac_isr' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack arg to netdev_upper_dev_link and netdev_master_upper_dev_link
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mapping the RX DMA buffers, the driver was accidentally specifying
zero for the buffer length. Under normal circumstances, SWIOTLB does not
need to allocate a bounce buffer, so the address is just mapped without
checking the size field. This is why the error was not detected earlier.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC has the option of sending only a single pause frame when
flow control is enabled and the RX queue is full. Although sending
only one pause frame has little value, this would allow admins to
enable automatic flow control without having to worry about the EMAC
flooding nearby switches with pause frames if the kernel hangs.
The option is enabled by using the single-pause-mode private flag.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
