Separate the overflow handling from the hardware interrupt status analysis.
The interrupt status is a single register and is common for all PFs. The
first PF reading the register is not necessarily the one who overflowed.
All PFs must check their overflow status on every attention.
In this change we clear the sticky indication in the attention handler to
allow doorbells to be processed again as soon as possible, but running
the doorbell recovery is scheduled for the periodic handler to reduce the
time spent in the attention handler.
Checking the need for DORQ flush was changed to "db_bar_no_edpm" because
qed_edpm_enabled()'s result could change dynamically and might have
prevented a needed flush.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the DORQ (doorbell block) is overflowed, all PFs get attentions at the
same time. If one PF finished handling the attention before another PF even
started, the second PF might miss the DORQ's attention bit and not handle
the attention at all.
If the DORQ attention is missed and the issue is not resolved, another
attention will not be sent, therefore each attention is treated as a
potential DORQ attention.
As a result, the attention callback is called more frequently so the debug
print was moved to reduce its quantity.
The number of periodic doorbell recovery handler schedules was reduced
because it was the previous way to mitigating the missed attention issue.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the condition which verifies that doorbell address is inside the
doorbell bar by checking that the end of the address is within range
as well.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DB_REC_DRY_RUN (running doorbell recovery without sending doorbells) is
never used. DB_REC_ONCE (send a single doorbell from the doorbell recovery)
is not needed anymore because by running the periodic handler we make sure
we check the overflow status later instead.
This patch is needed because in the next patches, the only doorbell
recovery type being used is DB_REC_REAL_DEAL, and the fixes are much
cleaner without this enum.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The patch introduces a new Multi-Function bit for cases where firmware
shouldn't perform the insertion of vlan-0 tag. The new bit is defined to
abstract the implementation from the actual MF mode.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read port count from the shared memory instead of driver deriving this
value. This change simplifies the driver implementation and also avoids
any dependencies for finding the port-count.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ll2 forwards all syn packets to the driver without validating the mac
address. Add validation check in the driver's iWARP listener flow and drop
the packet if it isn't intended for the device.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assumption that the maximum size of a syn packet is 128 bytes
is wrong. Tunneling headers were not accounted for.
Allocate buffers large enough for mtu.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some statements in an if-block that are not correctly
indented. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver interface to read the SmartAN capability from
management firmware.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Version update for qed/qede modules.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix unnecessary logging of message in an expected
default case where coalescing value read (via ethtool -c)
migh not be valid unless they are configured explicitly
in the hardware using ethtool -C.
Signed-off-by: Rahul Verma <rverma@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max supported queues is derived incorrectly in the case of multi-CoS.
Need to consider TCs while calculating num_queues for PF.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of Unified Fabric Port (UFP) mode, switch provides
the traffic class (TC) value to be used for the traffic.
Configure hardware to use this TC value for vlan priority.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When slowpath messages are sent with high rate, the resulting
events can lead to a FW assert in case they are not handled fast
enough (Event Queue Full assert). Attempt to send queued slowpath
messages only after the newly evacuated entries in the EQ ring
are indicated to FW.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache number of fragments in the skb locally as in case
of linear skb (with zero fragments), tx completion
(or freeing of skb) may happen before driver tries
to get number of frgaments from the skb which could
lead to stale access to an already freed skb.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs may hit VF-PF channel timeout while probing, as in some
cases it was observed that VF FLR and VF "acquire" message
transaction (i.e first message from VF to PF in VF's probe flow)
could occur simultaneously which could lead VF to fail sending
"acquire" message to PF as VF is marked disabled from HW perspective
due to FLR, which will result into channel timeout and VF probe failure.
In such cases, try retrying VF "acquire" message so that in later
attempts it could be successful to pass message to PF after the VF
FLR is completed and can be probed successfully.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF is always configured to drop control frames
(with reserved mac addresses) but to work LACP
on the VFs, it would require LACP control frames
to be forwarded or transmitted successfully.
This patch fixes this in such a way that trusted VFs
(marked through ndo_set_vf_trust) would be allowed to
pass the control frames such as LACP pdus.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running tx switched traffic between VNICs
created via a bridge(to which VFs are added),
adapter drops the unicast packets in tx flow due to
VNIC's ucast mac being unknown to it. But VF interfaces
being in promiscuous mode should have caused adapter
to accept all the unknown ucast packets. Later, it
was found that driver doesn't really configure tx
promiscuous mode settings to accept all unknown unicast macs.
This patch fixes tx promiscuous mode settings to accept all
unknown/unmatched unicast macs and works out the scenario.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initiating final cleanup after an ungraceful driver unload can lead to bad
PCI accesses towards the host.
This patch revises the load sequence so final cleanup is sent while the
internal master enable is cleared, to prevent the host accesses, and clears
the internal error indications just before enabling the internal master
enable.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:2126:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix regression in multi-SKB responses to RTM_GETADDR, from Arthur
Gautier.
2) Fix ipv6 frag parsing in openvswitch, from Yi-Hung Wei.
3) Unbounded recursion in ipv4 and ipv6 GUE tunnels, from Stefano
Brivio.
4) Use after free in hns driver, from Yonglong Liu.
5) icmp6_send() needs to handle the case of NULL skb, from Eric
Dumazet.
6) Missing rcu read lock in __inet6_bind() when operating on mapped
addresses, from David Ahern.
7) Memory leak in tipc-nl_compat_publ_dump(), from Gustavo A. R. Silva.
8) Fix PHY vs r8169 module loading ordering issues, from Heiner
Kallweit.
9) Fix bridge vlan memory leak, from Ido Schimmel.
10) Dev refcount leak in AF_PACKET, from Jason Gunthorpe.
11) Infoleak in ipv6_local_error(), flow label isn't completely
initialized. From Eric Dumazet.
12) Handle mv88e6390 errata, from Andrew Lunn.
13) Making vhost/vsock CID hashing consistent, from Zha Bin.
14) Fix lack of UMH cleanup when it unexpectedly exits, from Taehee Yoo.
15) Bridge forwarding must clear skb->tstamp, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
bnxt_en: Fix context memory allocation.
bnxt_en: Fix ring checking logic on 57500 chips.
mISDN: hfcsusb: Use struct_size() in kzalloc()
net: clear skb->tstamp in bridge forwarding path
net: bpfilter: disallow to remove bpfilter module while being used
net: bpfilter: restart bpfilter_umh when error occurred
net: bpfilter: use cleanup callback to release umh_info
umh: add exit routine for UMH process
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
vhost/vsock: fix vhost vsock cid hashing inconsistent
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
net: stmmac: Check if CBS is supported before configuring
net: stmmac: dwxgmac2: Only clear interrupts that are active
net: stmmac: Fix PCI module removal leak
tools/bpf: fix bpftool map dump with bitfields
tools/bpf: test btf bitfield with >=256 struct member offset
bpf: fix bpffs bitfield pretty print
net: ethernet: mediatek: fix warning in phy_start_aneg
tcp: change txhash on SYN-data timeout
...
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make sure chain element is updated before ringing the doorbell.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally deleted the code to set "rc = -ENOMEM;" and this patch
adds it back.
Fixes: d2201a2159 ("qed: No need for LL2 frags indication")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value for OEM_CFG_UPDATE command differs between driver and the
Management firmware (mfw). Fix this gap with adding a reserved field.
Fixes: cac6f69154 ("qed: Add support for Unified Fabric Port.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a DP_NOTICE message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the doorbelling entities are outside of the core module.
L2 queues, Roce queues, iscsi and fcoe all need to register.
Make the APIs available for these drivers.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Light L2 queues are doorbelling entities. Modify the implementation
to keep the doorbell data necessary for doorbelling in well known
location instead of recomputing every time. Register the LL2 queue
with doorbell recovery mechanism.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slow path queue is a doorbelling entity. Register it with the overflow mechanism.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of an attention from the doorbell queue block, analyze the HW
indications. In case of a doorbell overflow, execute a doorbell recovery.
Since there can be spurious indications (race conditions between multiple PFs),
schedule a periodic task for checking whether a doorbell overflow may have been
missed. After a set time with no indications, terminate the periodic task.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the database used to register doorbelling entities, and APIs for adding
and deleting entries, and logic for traversing the database and doorbelling
once on behalf of all entities.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The text in array s_igu_fifo_error_strs contains a spelling mistake,
fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for MBI image update through MFW.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW sends UFP notifications mostly during the device init phase and PFs
might not be assigned with a name by this time. Hence capturing port-id in
the debug messages would help in finding which PF the ufp notification was
sent to.
Also, fixed a minor scemantic issue in a debug print.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.
The patch consists of 3 fixes:
- When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
returned PQ 0, which can potentially be another function's pq. Verify
that flag is enabled, otherwise return default start_pq.
- When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
returned NULL and could lead to a segmentation fault. Return default
start_pq instead.
- A modulo operation was added to MCOS/VFS PQ getters to make sure the
PQ returned is in range of the required flag.
Fixes: b5a9ee7cf3 ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the condition which verifies that only one flag is set. The API
bitmap_weight() should receive size in bits instead of bytes.
Fixes: b5a9ee7cf3 ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing semicolon.
Fixes: 291d57f67d ("qed: Fix rdma_info structure allocation")
Cc: Michal Kalderon <michal.kalderon@cavium.com>
Cc: Denis Bolotin <denis.bolotin@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of "sb_index" is written by the hardware. Reading its value and
writing it to "index" must finish before checking the loop condition.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.
Fixes: 51ff17251c ("qed: Add support for RoCE hw init")
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TC received from APP TLV is stored in offload_tc, and should not be
set by protocols which did not receive an APP TLV. Fixed the condition
when overriding the offload_tc.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release PTT before entering error flow.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A stuck ramrod should be deleted from the completion_pending list,
otherwise it will be added again in the future and corrupt the list.
Return error value to inform that ramrod is stuck and should be deleted.
Signed-off-by: Sagiv Ozeri <sagiv.ozeri@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed_sp_destroy_request() API was added for SPQ users that need to
free/return the entry they acquired in their error flows.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are no SPQ entries left in the free_pool, new entries are
allocated and are added to the unlimited list. When an entry in the pool
is available, the content is copied from the original entry, and the new
entry is sent to the device. qed_spq_post() is not aware of that, so the
additional entry is stored in the original entry as p_post_ent, which can
later be returned to the pool.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free the allocated SPQ entry or return the acquired SPQ entry to the free
list in error flows.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:
drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.
Fixes: c56a8be7e7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static Checker Warnings:
drivers/net/ethernet/qlogic/qed/qed_main.c:1510 qed_fill_link_capability()
error: uninitialized symbol 'tcvr_state'.
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1951 qed_mcp_trans_speed_mask()
error: uninitialized symbol 'transceiver_state'.
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1951 qed_mcp_trans_speed_mask()
error: uninitialized symbol 'transceiver_type'.
Symbols tcvr_state, transceiver_state and transceiver_type
are initialized with respective default state.
Fixes: c56a8be7e7 ("qed: Add supported link and advertise link to display in ethtool.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_INFO message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly added link modes are required to be added
during setting link modes. If the new link mode
is not available during qed_set_link, it may cause
link getting down due to empty supported capability,
being passed to MFW, after setting autoneg off/on
with current/supported speed.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added transceiver type, speed capability and board types
in HSI, are utilizing to display the accurate link
information in ethtool.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added transceiver modes with different speed and media type,
speed capability and supported board types in HSI, which
will be utilizing to display correct specification of link
modes and speed type.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the use of local PTT to propagate through the qed_mcp* API's.
Global ptt should not be used.
Register access should be done through layers. Register address is
mapped into a PTT, PF translation table. Several interface functions
require a PTT to direct read/write into register. There is a pool of
PTT maintained, and several PTT are used simultaneously to access
device registers in different flows. Same PTT should not be used in
flows that can run concurrently.
To avoid running out of PTT resources, too many PTT should not be
acquired without releasing them. Every PF has a global PTT, which is
used throughout the life of PF, in most important flows for register
access. Generic functions acquire the PTT locally and release after
the use. This patch aligns the use of Global PTT and Local PTT
accordingly.
Signed-off-by: Rahul Verma <rahul.verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_INFO message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently driver registers to physical link notifications (of the device)
from Management firmware (MFW). Driver doesn't get notified if there's a
change in the virtual link e.g., link-flap on the peer PF interface.
Virtual link indication from MFW reflects the per PF link status instead
of the physical link.
The patch adds driver support for,
- Advertising the virtual link support to MFW.
- Handling the virtual link notification from MFW.
Please consider applying it to 'net-next'.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_ll2.c:799:32: warning: implicit
conversion from enumeration type 'enum core_tx_dest' to different
enumeration type 'enum qed_ll2_tx_dest' [-Wenum-conversion]
tx_pkt.tx_dest = p_ll2_conn->tx_dest;
~ ~~~~~~~~~~~~^~~~~~~
1 warning generated.
Fix this by using a switch statement to convert between the enumerated
values since they are not 1 to 1, which matches how the rest of the
driver handles this conversion.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Suggested-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver support for configuring/reading the 20G link speed.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake struct field name, rename it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure shared between driver and the management FW (mfw) differ in
sizes. This would lead to issues when driver try to access the structure
members which are not-aligned with the mfw copy e.g., data_ptr usage in the
case of mfw_tlv request.
Align the driver structure with mfw copy, add reserved field(s) to driver
structure for the members not used by the driver.
Fixes: dd006921d6 ("qed: Add MFW interfaces for TLV request support.)
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_delete_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:354:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_join_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:463:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]
Since commit 1eec2437d1 ("qed: Make OOO archipelagos into an array"),
'p_archipelago' is no longer in use.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1713:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV4;
~ ^~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1733:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV6;
~ ^~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, qed_tcp_ip_version:
TCP_IPV4 = QED_TCP_IPV4 = 0
TCP_IPV6 = QED_TCP_IPV6 = 1
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when a constant is used in a boolean context as it thinks a
bitwise operation may have been intended.
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
if (!p_iov->b_pre_fp_hsi &&
^
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: use '&' for a
bitwise operation
if (!p_iov->b_pre_fp_hsi &&
^~
&
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: remove constant
to silence this warning
if (!p_iov->b_pre_fp_hsi &&
~^~
1 warning generated.
This has been here since commit 1fe614d10f ("qed: Relax VF firmware
requirements") and I am not entirely sure why since 0 isn't a special
case. Just remove the statement causing Clang to warn since it isn't
required.
Link: https://github.com/ClangBuiltLinux/linux/issues/126
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_roce.c:153:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = ROCE_V2_IPV6;
~ ^~~~~~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_roce.c:156:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = MAX_ROCE_MODE;
~ ^~~~~~~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, roce_flavor:
ROCE_V2_IPV6 = RROCE_IPV6 = 2
MAX_ROCE_MODE = MAX_ROCE_FLAVOR = 3
While we're add it, ditch the local variable flavor, we can just return
the value directly from the switch statement.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang complains when one enumerated type is implicitly converted to
another.
drivers/net/ethernet/qlogic/qed/qed_vf.c:686:6: warning: implicit
conversion from enumeration type 'enum qed_tunn_mode' to different
enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
QED_MODE_L2GENEVE_TUNN,
^~~~~~~~~~~~~~~~~~~~~~
Update mask's parameter to expect qed_tunn_mode, which is what was
intended.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:163:25: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->vxlan.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:165:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:167:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:169:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_geneve.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:171:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_geneve.tun_cls = type;
~ ^~~~
5 warnings generated.
Avoid this by changing type to an int.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_VERBOSE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival cleanup, list_move_tail will implement the same function that
list_del() + list_add_tail() will do. hence just replace them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to configure the DORQ to use vlan-id/priority for
roce EDPM.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain multi-function switch dependent modes, firmware adds vlan tag 0
to the untagged frames. This leads to double tagging for the traffic
if the dcbx is enabled, which is not the desired behavior. To avoid this,
driver needs to set "dcb_dont_add_vlan0" flag.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-function mode, driver receives the stag value (outer vlan)
for a PF from management FW (MFW). If the stag value is negotiated prior to
the driver load, then the stag is not notified to the driver and hence
driver will have the invalid stag value.
The fix is to request the MFW for STAG value during the driver load time.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new qed firmware with fixes and support for new features.
Fixes:
- Fix a rare case of device crash with iWARP, iSCSI or FCoE offload.
- Fix GRE tunneled traffic when iWARP offload is enabled.
- Fix RoCE failure in ib_send_bw when using inline data.
- Fix latency optimization flow for inline WQEs.
- BigBear 100G fix
RDMA:
- Reduce task context size.
- Application page sizes above 2GB support.
- Performance improvements.
ETH:
- Tenant DCB support.
- Replace RSS indirection table update interface.
Misc:
- Debug Tools changes.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver displays an error message for each unrecognized dcbx TLV that's
received from the peer or configured on the device. It is observed that
syslog will be flooded with such messages in certain scenarios e.g.,
frequent link-flaps/lldp-transactions. Changing the severity of this
message to verbose level as it's not an error scenario/message.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep sending mailbox commands to the MFW when it is not responsive ends up
with a redundant amount of timeout expiries.
This patch prints the MCP status on the first command which is not
responded, and blocks the following commands.
Since the (un)load request commands might be not responded due to other
PFs, the patch also adds the option to skip the blocking upon a failure.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFW manages an internal lock to prevent concurrent hardware
(de)initialization of different PFs.
This, together with the busy-waiting for the MFW's responses for commands,
might lead to a deadlock during concurrent load or unload of PFs.
This patch adds the option to sleep within the busy-waiting, and uses it
for the (un)load requests (which are not sent from an interrupt context) to
prevent the possible deadlock.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Successive iterations of halting and resuming the management chip (MCP)
might fail, since currently the driver doesn't wait for these operations to
actually take place.
This patch prevents the driver from moving forward before the operations
are reflected in the state register.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFW might be reset and re-update its shared memory.
Upon the detection of such a reset the driver rereads this memory, but it
has to wait till the data is valid.
This patch adds the missing wait for a data ready indication.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for tc mqprio offload,
using this different traffic classes on the adapter
can be utilized based on configured priority to tc map.
For example -
tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3
This will cause SKBs with priority 0,1,2,3 to transmit
over tc 0,1,2,3 hardware queues respectively.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the code comments with
a proper "fall through" annotation, which is what GCC is expecting
to find.
Addresses-Coverity-ID: 114809 ("Missing break in switch")
Addresses-Coverity-ID: 114810 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE qps use a pair of physical queues (pq) received from the Queue Manager
(QM) - an offload queue (OFLD) and a low latency queue (LLT). The QM block
creates a pq for each TC, and allows RoCE qps to ask for a pq with a
specific TC. As a result, qps with different VLAN priorities can be mapped
to different TCs, and employ features such as PFC and ETS.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish not set offload_tc from offload_tc 0 and add getters and
setters.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The API receives a priority and looks for the TC it is mapped to in the
operational DCBX configuration. The API returns QED_DCBX_DEFAULT_TC (0)
when DCBX is disabled.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no in-tree callers of qed_get_cm_pq_idx_rl since it be there,
so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no in-tree callers of qed_set_gft_event_id_cm_hdr.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW hsi contains 256 approximation buckets which are split in ramrod into
eight u32 values, but driver is using eight 'unsigned long' variables.
This patch fixes the mcast logic by making the API utilize u32.
Fixes: 83aeb933 ("qed*: Trivial modifications")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds qed APIs for reading the PHY module.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in qed_probe message.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If format_idx == s_mcp_trace_meta.formats_num then we read one element
beyond the end of the s_mcp_trace_meta.formats[] array.
Fixes: 50bc60cb15 ("qed*: Utilize FW 8.33.11.0")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration information read at driver load can become stale after it is
updated. Mark information as not valid and re-populate when this happens.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer 'name' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'name' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct size value while copying chassis/port id values.
Fixes: 6ad8c632e ("qed: Add support for query/config dcbx.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.
Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not advertise DCBX_LLD_MANAGED capability i.e., do not allow
external agent to manage the dcbx/lldp negotiation. MFW acts as lldp agent
for qed* devices, and no other lldp agent is allowed to coexist with mfw.
Also updated a debug print, to not to display the redundant info.
Fixes: a1d8d8a51 ("qed: Add dcbnl support.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling a SIMD fastpath handler if it is NULL. The check is needed
to handle an unlikely scenario where unsolicited interrupt is destined to
a PF in INTa mode.
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory for packet buffers need to be freed in the error paths as there is
no consumer (e.g., upper layer) for such packets and that memory will never
get freed.
The issue was uncovered when port was attacked with flood of isatap
packets, these are multicast packets hence were directed at all the PFs.
For foce PF, this meant they were routed to the ll2 module which in turn
drops such packets.
Fixes: 0a7fb11c ("qed: Add Light L2 support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features.
RDMA
- Several modifications and fixes for Memory Windows
- drop vlan and tcp timestamp from mss calculation in driver for
this FW
- Fix SQ completion flow when local ack timeout is infinite
- Modifications in t10dif support
ETH
- Fix aRFS for tunneled traffic without inner IP.
- Fix chip configuration which may fail under heavy traffic conditions.
- Support receiving any-VNI in VXLAN and GENEVE RX classification.
iSCSI / FcoE
- Fix iSCSI recovery flow
- Drop vlan and tcp timestamp from mss calc for fw 8.37.2.0
Misc
- Several registers (split registers) won't read correctly with
ethtool -d
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring SRQ and provides the necessary
APIs for rdma upper layer driver (qedr) to enable the SRQ feature.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Yuval Bason <yuval.bason@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorrect shared memory address is used while deriving the values
for tc and pri_type. Use shmem address corresponding to 'oem_cfg_func'
where the management firmare saves tc/pri_type values.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure shared between driver and management firmware (MFW)
differ in sizes. The additional field defined by the MFW is not
relevant to the current driver. Add a dummy field to the structure.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes for capturing the link change count in
ethtool statistics display.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove and coalesce formats when there is an unnecessary
character after a logging newline. These extra characters
cause logging defects.
Miscellanea:
o Coalesce formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, User can configure for the supported
flows to be dropped. Added a stat "gft_filter_drop"
as well to be populated in ethtool for the dropped flows.
For example -
ethtool -N p5p1 flow-type udp4 dst-port 8000 action -1
ethtool -N p5p1 flow-type tcp4 scr-ip 192.168.8.1 action -1
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver supports flow classification to PF
receive queues based on TCP/UDP 4 tuples [src_ip, dst_ip,
src_port, dst_port] only.
This patch enables to configure different flow profiles
[For example - only UDP dest port or src_ip based] on the
adapter so that classification can be done according to
just those fields as well. Although, at a time just one
type of flow configuration is supported due to limited
number of flow profiles available on the device.
For example -
ethtool -N enp7s0f0 flow-type udp4 dst-port 45762 action 2
ethtool -N enp7s0f0 flow-type tcp4 src-ip 192.16.4.10 action 1
ethtool -N enp7s0f0 flow-type udp6 dst-port 45762 action 3
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW requests the TLVs in interrupt context. Extracting of the required
data from upper layers and populating of the TLVs require process context.
The patch adds work-queues for processing the tlv requests. It also adds
the implementation for requesting the tlv values from appropriate protocol
driver.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for processing TLV requests/repsonses
from the mfw and upper driver layers respectively. The implementation
reads the requested TLVs from the shared memory, requests the values
from upper layer drivers, populates this info (TLVs) shared memory and
notifies MFW about the TLV values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required management firmware (MFW) interfaces such as
mailbox commands, TLV types etc.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.
Fix that mask to handle 64bit physical address.
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stress on qedi/qedr load unload lead to list_del corruption.
This is due to ll2 connection terminate freeing resources without
verifying that no more ll2 processing will occur.
This patch unregisters the ll2 status block before terminating
the connection to assure this race does not occur.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ll2 flows of flushing the txq/rxq need to be synchronized with the
regular fp processing. Caused list corruption during load/unload stress
tests.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should free all pending isles once it gets a FLUSH cqe from FW.
Part of iSCSI out of order flow.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stress on qedi/qedr load unload lead to list_del corruption.
This is due to ll2 connection terminate freeing resources without
verifying that no more ll2 processing will occur.
This patch unregisters the ll2 status block before terminating
the connection to assure this race does not occur.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ll2 flows of flushing the txq/rxq need to be synchronized with the
regular fp processing. Caused list corruption during load/unload stress
tests.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should free all pending isles once it gets a FLUSH cqe from FW.
Part of iSCSI out of order flow.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_VERBOSE message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qede driver was loaded on a device configured for iWARP
the l2 mutex wouldn't be allocated, and some l2 related
resources wouldn't be freed.
fixes: c851a9dc43 ("qed: Introduce iWARP personality")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for new Multi function mode wherein the traffic
classification is done based on the 802.1ad tagging and the outer vlan tag
provided by the management firmware.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data member 'is_mf_default' is not used by the qed/qede drivers,
removing the same.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_NOTICE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_INFO message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strscpy() was a recent fix (net: qed: use correct strncpy() size) to
prevent passing the length of the source buffer to strncpy() and guarantee
null termination.
It misses the goal of overwriting only the first 3 characters in
"???_BIG_RAM" and "???_RAM" while keeping the rest of the string.
Use strncpy() with the length of 3, without null termination.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration information is added to the debug data collection, in
addition to register dump.
Added qed_dbg_nvm_image() that receives an image type, allocates a
buffer and reads the image. The images are saved in the buffers and the
dump size is updated.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nvm images attributes are cached during driver load, acquiring ptt
is not needed when calling qed_mcp_get_nvm_image().
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be a need for VF driver to request PF to explicitly update its
bulletin with a MAC address.
e.g. When user assigns a MAC address to VF while VF is still down,
and PF's bulletin board contains different MAC address, in this case,
when VF's interface is brought up, it gets loaded with MAC address from
bulletin board which is not desirable.
To handle this corner case, we need a new TLV to request PF to update
its bulletin board with suggested MAC.
This request will be honored only for trusted VFs.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per existing behavior, when PF sets a MAC address for a VF
(also called as forced MAC), VF is not allowed to change its
MAC address afterwards.
This puts the limitation on few use cases such as bonding of VFs,
where bonding driver asks VF to change its MAC address.
This patch uses a VF trust mode to allow VF to change its MAC address
in spite PF has set a forced MAC for that VF.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
This patch adds the required driver support for updating the flash or
non volatile memory of the adapter. At highlevel, flash upgrade comprises
of reading the flash images from the input file, validating the images and
writing them to the respective paritions.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds APIs for flash access.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for populating the flash image attributes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features
RDMA Features
- SRQ support
- XRC support
- Memory window support
- RDMA low latency queue support
- RDMA bonding support
RDMA bug fixes
- RDMA remote invalidate during retransmit fix
- iWARP MPA connect interop issue with RTR fix
- iWARP Legacy DPM support
- Fix MPA reject flow
- iWARP error handling
- RQ WQE validation checks
MISC
- Fix some HSI types endianity
- New Restriction: vlan insertion in core_tx_bd_data can't be set
for LB packets
ETH
- HW QoS offload support
- Fix vlan, dcb and sriov flow of VF sending a packet with
inband VLAN tag instead of default VLAN
- Allow GRE version 1 offloads in RX flow
- Allow VXLAN steering
iSCSI / FcoE
- Fix bd availability checking flow
- Support 256th sge proerly in iscsi/fcoe retransmit
- Performance improvement
- Fix handle iSCSI command arrival with AHS and with immediate
- Fix ipv6 traffic class configuration
DEBUG
- Update debug utilities
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes spelling typos found in printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
FW workaround. The iWARP LL2 connection did not expect TCP packets
to arrive on it's connection. The fix drops any non-tcp packets
Fixes b5c29ca ("qed: iWARP CM - setup a ll2 connection for handling
SYN packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a corner case in the MPA unalign flow where a FPDU header is
split over two tcp segments. The length of the first fragment in this
case was not initialized properly and should be '1'
Fixes: c7d1d839 ("qed: Add support for MPA header being split over two tcp packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're dereferencing "p_hwfn->p_rdma_info" but that is freed on the line
before in qed_rdma_resc_free(p_hwfn).
Fixes: 9de506a547 ("qed: Free RoCE ILT Memory on rmmod qedr")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rdma requires ILT Memory to be allocated for it's QPs.
Each ILT entry points to a page used by several Rdma QPs.
To avoid allocating all the memory in advance, the rdma
implementation dynamically allocates memory as more QPs are
added, however it does not dynamically free the memory.
The memory should have been freed on rmmod qedr, but isn't.
This patch adds the memory freeing on rmmod qedr (currently
it will be freed with qed is removed).
An outcome of this bug, is that if qedr is unloaded and loaded
without unloaded qed, there will be no more RoCE traffic.
The reason these are related, is that the logic of detecting the
first QP ever opened is by asking whether ILT memory for RoCE has
been allocated.
In addition, this patch modifies freeing of the Task context to
always use the PROTOCOLID_ROCE and not the protocol passed,
this is because task context for iWARP and ROCE both use the
ROCE protocol id, as opposed to the connection context.
Fixes: dbb799c397 ("qed: Initialize hardware for new protocols")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: This is compile only tested as I have no access to the hw.
Constifying and declaring as static saves 24 bytes.
add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-24 (-24)
Function old new delta
pkt_type_str 24 - -24
Total: Before=3599256, After=3599232, chg -0.00%
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Acked-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
passing the strlen() of the source string as the destination
length is pointless, and gcc-8 now warns about it:
drivers/net/ethernet/qlogic/qed/qed_debug.c: In function 'qed_grc_dump':
include/linux/string.h:253: error: 'strncpy' specified bound depends on the length of the source argument [-Werror=stringop-overflow=]
This changes qed_grc_dump_big_ram() to instead uses the length of
the destination buffer, and use strscpy() to guarantee nul-termination.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this cycle were:
- Updates to use cond_resched() instead of cond_resched_rcu_qs()
where feasible (currently everywhere except in kernel/rcu and in
kernel/torture.c). Also a couple of fixes to avoid sending IPIs to
offline CPUs.
- Updates to simplify RCU's dyntick-idle handling.
- Updates to remove almost all uses of smp_read_barrier_depends() and
read_barrier_depends().
- Torture-test updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
torture: Save a line in stutter_wait(): while -> for
torture: Eliminate torture_runnable and perf_runnable
torture: Make stutter less vulnerable to compilers and races
locking/locktorture: Fix num reader/writer corner cases
locking/locktorture: Fix rwsem reader_delay
torture: Place all torture-test modules in one MAINTAINERS group
rcutorture/kvm-build.sh: Skip build directory check
rcutorture: Simplify functions.sh include path
rcutorture: Simplify logging
rcutorture/kvm-recheck-*: Improve result directory readability check
rcutorture/kvm.sh: Support execution from any directory
rcutorture/kvm.sh: Use consistent help text for --qemu-args
rcutorture/kvm.sh: Remove unused variable, `alldone`
rcutorture: Remove unused script, config2frag.sh
rcutorture/configinit: Fix build directory error message
rcutorture: Preempt RCU-preempt readers more vigorously
torture: Reduce #ifdefs for preempt_schedule()
rcu: Remove have_rcu_nocb_mask from tree_plugin.h
rcu: Add comment giving debug strategy for double call_rcu()
tracing, rcu: Hide trace event rcu_nocb_wake when not used
...
Issue found by checkpatch.
Signed-off-by: Rohit Visavalia <rohit.visavalia@softnautics.com>
Acked-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A tid was allocated for reserved MR during initialization but
not freed. This lead to an annoying output message during
rdma unload flow.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Double reservation for kernel dedicated dpi was performed.
Once in the core module and once in qedr.
Remove the reservation from core.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check if p_ent->comp_mode is QED_SPQ_MODE_EBLOCK before
calling qed_spq_add_entry(). The test is fine is the mode is EBLOCK,
but if it isn't then qed_spq_add_entry() might kfree(p_ent).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_zalloc_coherent and vzalloc for allocating zeroed
memory and remove unnecessary memset function.
Done using Coccinelle.
Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
0-day tested with no failures.
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advance the qed* drivers to use firmware 8.33.1.0:
Modify core driver (qed) to utilize the new FW and initialize the device
with it. This is the lion's share of the patch, and includes changes to FW
interface files, device initialization flows, FW interaction flows, and
debug collection flows.
Modify Ethernet driver (qede) to make use of new FW in fastpath.
Modify RoCE/iWARP driver (qedr) to make use of new FW in fastpath.
Modify FCoE driver (qedf) to make use of new FW in fastpath.
Modify iSCSI driver (qedi) to make use of new FW in fastpath.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Bason <Yuval.Bason@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames defines and structures in the FW HSI files to allow a
distinction between different types of HW.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors and reorders the FW API files in preparation of
upgrading the code to support new FW.
- Make use of the BIT macro in appropriate places.
- Whitespace changes to align values and code blocks.
- Comments are updated (spelling mistakes, removed if not clear).
- Group together code blocks which are related or deal with similar
matters.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __qed_spq_block() function expects an smp_read_barrier_depends()
to order a prior READ_ONCE() against a later load that does not depend
on the prior READ_ONCE(), an expectation that can fail to be met.
This commit therefore replaces the READ_ONCE() with smp_load_acquire()
and removes the smp_read_barrier_depends().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: <everest-linux-l2@cavium.com>
Cc: <netdev@vger.kernel.org>
Replace kmalloc followed by a memset with kzalloc
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ariel Elior <aelior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Out of order flow is not working for iWARP.
This patch got cut out from initial series that added out
of order support for iWARP.
Make out of order code common for iWARP and iSCSI.
Add new configuration option CONFIG_QED_OOO. Set by
qedr and qedi Kconfigs.
Fixes: d1abfd0b4e ("qed: Add iWARP out of order support")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We continue to maintain a maximum of three buffers per fpdu, to ensure
that there are enough buffers for additional unaligned mpa packets.
To support this, if a fpdu is split over more than two tcp packets, we
use an intermediate buffer to copy the data to the previous buffer, then
we can release the data. We need an intermediate buffer as the initial
buffer partial packet could be located at the end of the packet, not
leaving room for additional data. This is a corner case, and will usually
not be the case.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a special case where an MPA header is split over to tcp
packets, in this case we need to wait for the next packet to
get the fpdu length. We use the incomplete_bytes to mark this
fpdu as a "special" one which requires updating the length with
the next packet
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When posting a packet on the ll2 tx, we can provide a cookie that
will be returned upon tx completion. This cookie is the ll2 iwarp buffer
which is then reposted to the rx ring. Part of the unaligned mpa flow
is determining when a buffer can be reposted. Each buffer needs to be
sent only once as a cookie for on the tx ring. In packed fpdu case, only
the last packet will be sent with the buffer, meaning we need to handle the
case that a cookie can be NULL on tx complete. In addition, when a fpdu
splits over two buffers, but there are no more fpdus on the second buffer,
two buffers need to be provided as a cookie. To avoid changing the ll2
interface to provide two cookies, we introduce a piggy buf pointer,
relevant for iWARP only, that holds a pointer to a second buffer that
needs to be released during tx completion.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fpdu data structure is preallocated per connection.
Each connection stores the current status of the connection:
either nothing pending, or there is a partial fpdu that is waiting for
the rest of the fpdu (incomplete bytes != 0).
The same structure is also used for splitting a packet when there are
packed fpdus. The structure is initialized with all data required
for sending the fpdu back to the FW. A fpdu will always be spanned across
a maximum of 3 tx bds. One for the header, one for the partial fdpu
received and one for the remainder (unaligned) packet.
In case of packed fpdu's, two fragments are used, one for the header
and one for the data.
Corner cases are not handled in the patch for clarity, and will be added
as a separate patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mpa buff is a descriptor for iwarp ll2 buffers that contains
additional information required for aligining fpdu's.
In some cases, an additional packet will arrive which will complete
the alignment of a fpdu, but we won't be able to post the fpdu due to
insufficient place on the tx ring. In this case we can't loose the data
and require storing it for later. Processing is therefore done
in two places, during rx completion, where we initialize a mpa buffer
descriptor and add it to the pending list, and during tx-completion, since
we free up an entry in the tx chain we can process any pending mpa packets.
The mpa buff descriptors are pre-allocated since we have to ensure that
we won't reach a state where we can't store an incoming unaligned packet.
All packets received on the ll2 MUST be processed by the driver at some
stage. Since they are preallocated, we hold a free list.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds only the establishment and termination of the
ll2 connection that handles unaligned MPA packets.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For iWARP unaligned MPA flow, a slowpath event of flushing an
MPA connection that entered an unaligned state is required.
The flush ramrod is received on the ll2 queue, and a pre-registered
callback function is called to handle the flush event.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet is sent back to iWARP FW via the tx ll2 connection
the FW needs to know the source of the packet. Whether it is
OOO or unaligned MPA related. Since OOO is implemented entirely
inside the ll2 code (and shared with iSCSI), packets are marked
as IN_ORDER inside the ll2 code. For unaligned mpa the value
will be determined in the iWARP code and sent on the pkt->vlan
field.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enable_ip_cksum, enable_l4_cksum, calc_ip_len were added in
commit stated below but not passed through to FW. This was OK
until now as it wasn't used, but is required for the iWARP
unaligned flow
Fixes:7c7973b2ae27 ("qed: LL2 to use packed information for tx")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option of sending a packet on the ll2 and dropping it exists in
hardware and was not used until now, thus not exposed.
The iWARP unaligned MPA flow requires this functionality for
flushing the tx queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When more than one ll2 queue is opened ( that is not an OOO queue )
ll2 code does not have enough information to determine whether
the queue is the main one or not, so a new field is added to the
acquire input data to expose the control of determining whether
the queue is the main queue or a secondary queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP uses 3 ll2 connections, the maximum number of bds is known
during connection setup. This patch modifies the static array in
the ll2_tx_packet descriptor to be a flexible array and
significantlly reduces memory size.
In addition, some redundant fields in the ll2_tx_packet were
removed, which also contributed to decreasing the descriptor size.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dcb_app priority is unsigned thus checking whether it is less than zero
is redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Acked-By: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SYN packet which arrives with errors from FW should be dropped.
This required adding an additional field to the ll2
rx completion data.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum number of CQs supported is bound to the number
of connections supported, which differs between RoCE and iWARP.
This fixes a crash that occurred in iWARP when running 1000 sessions
using perftest.
Fixes: 67b40dccc4 ("qed: Implement iWARP initialization, teardown and qp operations")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP requires OOO support which is already provided by the ll2
interface (until now was used only for iSCSI offload).
The changes mostly include opening a ll2 dedicated connection for
OOO and notifiying the FW about the handle id.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the last of the initial iWARP patch series. It
adds the possiblity to actually detect iWARP from the device and enable
it in the critical locations which basically make iWARP available.
It wasn't submitted until now as iWARP hadn't been accepted into
the rdma tree.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.
Semantic patch used to resolve this issue:
@@
expression e,e2; constant c;
statement S;
@@
e = kzalloc(e2, c);
if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Sudarsana Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_NOTICE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate 'p_info->mfw_mb_cur' and 'p_info->mfw_mb_shadow' but we check
'p_info->mfw_mb_addr' instead of 'p_info->mfw_mb_cur'.
'p_info->mfw_mb_addr' is never 0, because it is initiliazed a few lines
above in 'qed_load_mcp_offsets()'.
Update the test and check the result of the 2 'kzalloc()' instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve the actual coalesce value from hardware for every Rx/Tx
queue, instead of Rx/Tx coalesce value cached during set coalesce.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the ethtool support to set RX/Tx coalesce
value to the VF associated Rx/Tx queues.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required driver support for reading/configuring the
Energy Efficient Ethernet (EEE) parameters.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for adding and deleting rx flow
classification rules. Using this user can classify RX flow
constituting of TCP/UDP 4-tuples [src_ip/dst_ip and src_port/dst_port]
to be steered on a given RX queue
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option "h" (host order ) exists for ipv4 only.
Remove the h when printing ipv6 addresses.
Lead to the following smatch warning:
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:585 qed_iwarp_print_tcp_ramrod()
warn: '%pI6' can only be followed by c
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1521 qed_iwarp_print_cm_info()
warn: '%pI6' can only be followed by c
Fixes commit 456a584947 ("qed: iWARP CM add passive side connect")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix compilation warning
qed_iwarp.c:1721:5: warning: ll2_syn_handle may be used
uninitialized in this function
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP has different physical queue requirements than RoCE
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When computing how much memory is required for the different hw clients
iWARP protocol should be taken into account
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces error handling for errors that occurred during
connection establishment.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of active/passive disconnect flows.
Disconnect flows can be initiated remotely, in which case a async event
will arrive from peer and indicated to qedr driver. These
are referred to as exceptions. When a QP is destroyed, it needs to check
that it's associated ep has been closed.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the active side connect.
Offload a connection, process MPA reply and send RTR.
In some of the common passive/active functions, the active side
will work in blocking mode.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the passive side connect.
It addresses pre-allocating resources, creating a connection
element upon valid SYN packet received. Calling upper layer and
implementation of the accept/reject calls.
Error handling is not part of this patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to add and remove listeners and identify
whether the SYN packet received is intended for iWARP or not. If
a listener is not found the SYN packet is posted back to the chip.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP handles incoming SYN packets using the ll2 interface. This patch
implements ll2 setup and teardown. Additional ll2 connections will
be used in the future which are not part of this patch series.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new connection type for iWARP ll2 connections for setting
correct ll2 filters and connection type to FW.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make some names more generic as they will be used by iWARP too.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds iWARP support for flows that have common code
between RoCE and iWARP, such as initialization, teardown and
qp setup verbs: create, destroy, modify, query.
It introduces the iWARP specific files qed_iwarp.[ch] and
iwarp_common.h
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP personality introduced the need for differentiating in several
places in the code whether we are RoCE, iWARP or either. This
leads to introducing new macros for querying the personality.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the qed_roce_if file to qed_rdma_if as it
represents a common interface for RoCE and iWARP.
this commit affects RDMA/qedr as well.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch places common iWARP / RoCE code in qed_rdma
and roce specific code in qed_roce
There is one new function ( qed_roce_setup ) added, the rest
of the patch removes content from the files and removes some
static definitions.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds files that will contain common code for RoCE/iWARP.
The files are currently identical to qed_roce.c / qed_roce.h and
intentionally not added to the makefile. The next patch in the series
will modify the files so that roce specific code is left in qed_roce
and common roce/iwarp code will be placed in qed_rdma
This patch is the result of a simple
cp qed_rdma.c qed_roce.c
cp qed_rdma.h qed_roce.h
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch in the series will duplicate qed_roce as part
of code preprations for iWARP support. Do some cleanup before
duplicating
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever firmware indicates that there's an async indication it needs
to handle, there's a switch-case where the right functionality is called
based on function's personality and information.
Before iWARP is added [as yet another client], switch over the SPQ into
a callback-registered mechanism, allowing registration of the relevant
event-processing logic based on the function's personality. This allows
us to tidy the code by removing protocol-specifics from a common file.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver needs to wait for all resources to return from FW before it can send
the FUNC_CLOSE ramrod.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DCBx update occurs while QPs are open, stop sending edpms until all
QPs are closed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure device according to DCBx results so that EDPMs
made by RoCE would honor flow-control.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP would require the chains to allocate/free their PBL memory
independently, so add the infrastructure to provide it externally.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The p_l2_info->pp_qid_usage[] array has "p_l2_info->queues" elements so
the > here should be a >= or we write beyond the end of the array.
Fixes: bbe3f233ec ("qed: Assign a unique per-queue index to queue-cid")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_QED_SRIOV is disabled, we get a build error:
drivers/net/ethernet/qlogic/qed/qed_int.c: In function 'qed_int_sb_init':
drivers/net/ethernet/qlogic/qed/qed_int.c:1499:4: error: implicit declaration of function 'qed_vf_set_sb_info'; did you mean 'qed_mcp_get_resc_info'? [-Werror=implicit-function-declaration]
All the other declarations have a 'static inline' stub as an alternative
here, so this adds one more for qed_int_sb_init.
Fixes: 50a207147f ("qed: Hold a single array for SBs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LL2 statistics already have place holders for these, but haven't
populated them so far.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver to inform the connection owner that the its buffers are being
released as part of a flush.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a legacy leftover; There's no current flow where 'frags_mapped'
would be set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LL2 today is interrupt driven - when tx/rx completion arrives [or any
other indication], qed needs to operate on the connection and pass
the information to the protocol-driver [or internal qed consumer].
Since we have several flavors of ll2 employeed by the driver,
each handler needs to do an if-else to determine the right functionality
to use based on the connection type.
In order to make things more scalable [given that we're going to add
additional types of ll2 flavors] move the infrastrucutre into using
a callback-based approach - the callbacks would be provided as part
of the connection's initialization parameters.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having the OOO logic packetd, divide it with rest of code
according to establish/release flows.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A LL2 connection [qed_ll2_info] has a sub-structure of type qed_ll2_conn
that contain various inputs for ll2 acquisition, but the connection also
utilizes a couple of other inputs.
Restructure the input structure to include all the inputs and refactor
the code necessary to populate those.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces qed_ll2_comp_rx_data as a public struct
and moves handling of Rx packets in LL2 into using it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step in revising the LL2 interface, this declares
qed_ll2_tx_pkt_info as part of the ll2 interface, and uses it for
transmission instead of receiving lots of parameters.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The final addition on the qed front -
- VFs would now require their PFs to provide multiple CIDs
- Based on the availability of connections from PF, determine whether
XDP is feasible and share it with qede via dev_info.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently not mapping their doorbell bar, instead relying
on the small doorbell window they have in their limited regview bar.
In order to increase the number of possible Tx connections [queues]
employeed by VF past 16, we need to start using the doorbell bar if
one such is exposed - VF would communicate this fact to PF which would
return the size-bar internally configured into chip, according to
which the VF would decide whether to actually utilize the doorbell
bar.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the infrastructure for supporting VFs that want to open
multiple transmission queues on the same queue-zone.
At this point, there are no VFs that actually request this functionality,
but later patches would remedy that.
a. VF and PF would communicate the capability during ACQUIRE;
Legacy VFs would continue on behaving as they do today
b. PF would communicate number of supported CIDs to the VF
and would enforce said limitation
c. Whenever VF passes a request for a given queue configuration
it would also pass an associated index within said queue-zone
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the infrastructure a PF maintains for each one of its VFs
to support multiple queue-cids on a single queue-zone.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now we used to have a single VF legacy compatibility mode,
one that affected the place of the Rx producers of those VFs [mostly].
As PF would soon support allocating CIDs for VFs instead of having
a static CID<->queue configuration for them, we'll need to have
an additional legacy mode since existing VFs would need to continue
on using the older mode of operation.
Change the infrastrucutre so that the legacy would be able to indicate
which of the legacy behaviors is needed for a given VF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a queue-cid is allocated, assign an index inside that's
CID's queue-zone.
For PFs and VFS, this number is going to be unique and derive
from a per-queue-zone bitmap, while for PF's VFs queues the
number is currently going to constant; Later, we'd add the
capability of a VF to communicate such an index to its PF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to need additional information for queue-cids
that a PF creates for its VFs, so start by refactoring existing
logic used for initializing said struct into receiving a structure
encapsulating the VF-specific information that needs to be provided.
This also introduces QED_QUEUE_CID_SELF - each queue-cid would hold
an indication to whether it belongs to the hw-function holding it
[whether that's a PF or a VF], or else what's the VF id it belongs
to.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of an effort of a cleaner seperation between qed and the protocol
drivers, the L2 interface is to use the SB structure for initialization
purposes opaquely.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step in allowing a single PF/VF to open multiple queues on
the same queue zone is to add per-hwfn database of queue-cids
as a two-dimensional array where entry would be according to
[queue zone][internal index].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each PF has a bitmap for its own ranges of CIDs, to allow easy grabbing
of an available CID when such is needed. But VFs are not using the same
mechanism, instead relying on hard-coded CIDs [ queue-index == cid ].
As an infrastructure step toward increasing number of CIDs of VFs,
the PF is going to maintain bitmaps for the VF CIDs as well -
the bitmaps would be per-VF and the ranges would be the same [in HW all
VFs of a given PF have the same mapping of CIDs, and the HW is capable
of distinguishing between those according to the VF index]
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance API between qedi and qed, allowing qedi to inform device's
firmware when the iSCSI mac is to be changed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storage drivers require images from the nvram in boot-from-SAN
scenarios. This provides the necessary API between qed and the
protocol drivers to perform such reads.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Share several new tidbits with qedf:
- wwpn & wwnn
- Absolute pf-id [this one is actually meant for qedi as well]
- Number of available CQs
While we're at it, now that qedf will be aware of the available CQs
we can add some validation on the inputs it provides.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver reads values via HSI splitting this 8-byte into 2 32-bit
values and builds a single u64 field - but it does so by shifting
the lower field instead of the higher.
Luckily, we still don't use these fields for anything - but we're about
to start.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're resetting the IGU CAM each time we initialize the PF
device, there's no need to reset the VF SBs again when initializing
IOV.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGU CAM contains an assocaition between hardware SBs
and interrupt lines, and it can be dynamically configured
to allow more interrupts in one entity over another, specifically
for Re-distibution of SBs between a PF and its child VFs.
While we don't yet use this functionality, there are other
clients that do and as such its possible the information
passed from management firmware during initialization in
regard to the possible number of SBs doesn't accurately reflect
the current HW configuration.
The following changes are going to apply to the driver init sequence:
a. PF is going to re-configure all entries belonging to itself and
its child VFs in IGU CAM based on the management firmware info
regarding the number of SBs that are supposed to exist there.
b. PF is going to stop using the SB resource [management firmware
provided information] for anything but the initialization.
Instead, it would use the live-time counters it maintains for
the numbers.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PF today holds 2 different arrays - one holding information
about the HW configuration and one holding information about
the SBs that are used by the protocol drivers.
These arrays aren't really connected - e.g., protocol driver
initializing a given SB would not mark the same SB as occupied
in the HW shadow array.
Move into a single array [at least for PFs] - hold the mapping
of the driver-protocol SBs on the HW entry which they configure.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOV code is very intrusive in its manipulation of the status block
database.
Add a new auxiliary function to allow the PF to find an available unused
status block to configure for a specific VF's MSI-x vector.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code assumes there's a known layout for SBs in the IGU,
where all the SBs of a single entity would be laid in consecutive
order of vectors.
While the assumption is still kept by management firmware, we already
have the necessary information to eliminate it, so no reason to keep
it in code.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have an API struct that contains interrupt-related
numbers. Use it to encapsulate all information relating to the
status of SBs as (used|free).
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An additional step for relaxing the IGU order assumption, we now add
an auxiliary function that can be used for finding the HW status block
that's associated with a given MSI-x vector.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In qed code, sb_id means 2 different things:
- An interrupt vector [usually when received as a parameter from
a protocol driver, but not only] that's associated with a status
block.
- An index to a status block entity existing in HW.
This patch renames the references to the HW entity, adding an 'igu_'
prefix to allow an easier distinction.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a first step for relaxing various assumptions done by driver
about the IGU mapping, the driver is now going to read the entire
IGU into a shadow copy, and mark in its database each status block
that's relevant for it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the portions controlling interrupt enablement form those
controlling the ability of HW to generate attentions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation lacks the logic for providing management
firmware with RDMA-related statistics; [much] worse than that -
it logs such events by default to system logs.
Since the statistics' gathering is done periodically, using sufficiently
new management firmware the system logs would get filled with these
unnecessary prints.
For now, reduce the verbosity of the log so that it would not be
logged by default.
Fixes: 6c75424612 ("qed: Add support for NCSI statistics")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve PCI performance by adjusting padding sizes to match those of the
host machine's cacheline.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parities might exhibit a flood behavior since we re-enable the
attention line without preventing the parity from re-triggering the
assertion.
Mask the source in AEU until the parity would be handled.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In strucuture reflecting the AEU hw block some entries
represent multiple HW bits, and the associated name is in fact
a pattern.
Today, whenever such an attention would be asserted the resulted
prints would show the pattern string instead of indicating which
of the possible bits was set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 4 attention bits in AEU that have different meaning
for QL45xxx and QL41xxx adapters.
Instead of doing a massive infrastructure change in favor of these
bits, we implement a point fix where only those four would change
meaning dependent on the adapter involved.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have almost all the necessary information regarding attentions
in the logic employed for taking register dumps.
Add some more and get rid of the seperate implementation we have today
for identifying & printing various attention sources.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case management firmware indicates a change in the used S-tag,
propagate the configuration to HW and FW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QL41xxx adapters' PCI allows a single configuration for the
MSI-x table size of all child VFs of a given PF.
The existing code wouldn't cause the management firmware to set
that value, meaning the VFs would retain the default MSI-x table
size.
Introduce a new scheme so that whenever a VF is enabled, driver
would set the number of MSI-x to be the maximum over the various
VFs' needs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older firmware used by device didn't distinguish between RoCE and RoCE
V2 from DCBx configuration perspective, and as a result we've used to
take a the RoCE-related configuration and apply to it for both.
Since we now support configuring each its own values, there's no reason
to reflect [& configure] that both are using the same.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a boolean value that propagates to FW configuration,
use the proper firmware HSI values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some getters are not getting filled with the correct information
regarding local DCBx.
Fixes: 49632b5822 ("qed: Add support for static dcbx.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current API between qed and protocol modules allows passing an
additional private string - but it doesn't get utilized by qed
anywhere.
Clarify the API by removing it and renaming it 'set_name'.
CC: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass additional information about package installed on persistent memory
so that protocol drivers would be able to log it.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're closing the parser searching for RDMA when stoping the
fastpath, we need to re-enable it when starting the fastpath once again.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, driver has a synchronization point while closing
the device which synchronizes its slowpath interrupt line.
However, that's insufficient as that ISR would schedule the
slowpath-tasklet - so even after ISR is over it's possible the
handling of the interrupt has not completed.
By doing a disable/enable on the taskelt we guarantee that all
HW events that should no longer be genereated from that point
onward in the flow are truly behind us.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A0 never went public, so no need to protect against it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter reflects the number of physical ports connected to a single
engine, not all.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case nvram layout of board is incorrect, board may exhibit peculiar
oddities. Log such a rare event.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flows configuring tunnel ports in HW use the main_ptt which should
be reserved for core-functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The management firmware HSI contains masks which are already
shifted to their right place, so QED_MFW_SET_FIELD() is clearing
incorrect fields by shifting the mask by the offset.
Luckily, today we set the fields in an incrementing order [so we're
not erasing any previously set fields], but this still needs fixing.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If too many CQs are requested, qed would print the available
number as if it's a resource and not a feature leading to the
wrong print.
Fixes: 08737a3fa3 ("qed: Inform qedi the number of possible CQs")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-organize the logic that allocates and frees memory of various
sub-components of the hw-function -
a. No need to pass pointers to said structure as parameters;
The internal logic knows exactly where to find/set the data.
b. Nullify pointers after cleanup to prevent possible errors to
re-entrant code.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that is not needed.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pushes qed [and as result, all qed* drivers] into using 8.20.0.0
firmware. The changes are mostly contained in qed with minor changes
to qedi due to some HSI changes.
Content-wise, the firmware contains fixes to various issues exposed
since the release of the previous firmware, including:
- Corrects iSCSI fast retransmit when data digest is enabled.
- Stop draining packets when receiving several consecutive PFCs.
- Prevent possible assertion when consecutively opening/closing
many connections.
- Prevent possible assertion due to too long BDQ fetch time.
In addition, the new firmware would allow us to later add iWARP support
in qed and qedr.
Changes from previous version
-----------------------------
- V2: Fix warning in qed_debug.c
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current memset is using incorrect type of variable, causing the
upper-half of the strucutre to be left uninitialized and causing:
ethernet/qlogic/qed/qed_init_fw_funcs.c: In function 'qed_set_rfs_mode_disable':
ethernet/qlogic/qed/qed_init_fw_funcs.c:993:3: error: '*((void *)&ramline+4)' is used uninitialized in this function [-Werror=uninitialized]
Fixes: d51e4af5c2 ("qed: aRFS infrastructure support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix multiqueue in stmmac driver on PCI, from Andy Shevchenko.
2) cdc_ncm doesn't actually fully zero out the padding area is
allocates on TX, from Jim Baxter.
3) Don't leak map addresses in BPF verifier, from Daniel Borkmann.
4) If we randomize TCP timestamps, we have to do it everywhere
including SYN cookies. From Eric Dumazet.
5) Fix "ethtool -S" crash in aquantia driver, from Pavel Belous.
6) Fix allocation size for ntp filter bitmap in bnxt_en driver, from
Dan Carpenter.
7) Add missing memory allocation return value check to DSA loop driver,
from Christophe Jaillet.
8) Fix XDP leak on driver unload in qed driver, from Suddarsana Reddy
Kalluru.
9) Don't inherit MC list from parent inet connection sockets, another
syzkaller spotted gem. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
dccp/tcp: do not inherit mc_list from parent
qede: Split PF/VF ndos.
qed: Correct doorbell configuration for !4Kb pages
qed: Tell QM the number of tasks
qed: Fix VF removal sequence
qede: Fix XDP memory leak on unload
net/mlx4_core: Reduce harmless SRIOV error message to debug level
net/mlx4_en: Avoid adding steering rules with invalid ring
net/mlx4_en: Change the error print to debug print
drivers: net: wimax: i2400m: i2400m-usb: Use time_after for time comparison
DECnet: Use container_of() for embedded struct
Revert "ipv4: restore rt->fi for reference counting"
net: mdio-mux: bcm-iproc: call mdiobus_free() in error path
net: ethernet: ti: cpsw: adjust cpsw fifos depth for fullduplex flow control
ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf
net: cdc_ncm: Fix TX zero padding
stmmac: pci: split out common_default_data() helper
stmmac: pci: RX queue routing configuration
stmmac: pci: TX and RX queue priority configuration
stmmac: pci: set default number of rx and tx queues
...
When configuring the doorbell DPI address, driver aligns the start
address to 4KB [HW-pages] instead of host PAGE_SIZE.
As a result, RoCE applications might receive addresses which are
unaligned to pages [when PAGE_SIZE > 4KB], which is a security risk.
Fixes: 51ff17251c ("qed: Add support for RoCE hw init")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver doesn't pass the number of tasks to the QM init logic
which would cause back-pressure in scenarios requiring many tasks
[E.g., using max MRs] and thus reduced performance.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After previos changes in HW-stop scheme, VFs stopped sending CLOSE
messages to their PFs when they unload.
Fixes: 1226337ad9 ("qed: Correct HW stop flow")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver currently uses advertised-autoneg value to populate the
supported-autoneg field. When advertised field is updated, user gets
the same value for supported field. Supported-autoneg value need to be
populated from the link capabilities value returned by the MFW.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value for status block id could be more than 256 in 100G mode, need to
update its data type from u8 to u16.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware filter configuration performed by the driver for a given
user requested config is not correct for some of the PTP modes.
Following changes are needed for PTP config-filter implementation.
1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables
TimeSync/"V1 frame format support"/"V2 frame format support" on
the TX side. Set the associated bits based on the user request.
2. ptp4l application fails to operate in Peer Delay mode. Following
changes are needed to fix this,
a. Driver should enable (set to 0) DA #1-related bits for IPv4,
IPv6 and MAC destination addresses in these registers:
NIG_REG_TX_LLH_PTP_RULE_MASK
NIG_REG_LLH_PTP_RULE_MASK
b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should
be set to 0x0 in all modes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing the PTP related initialization from slowpath start,
the remaining PTT entry is required only in case CONFIG_RFS_ACCEL is set.
Otherwise, it leads to a warning due to it being unused.
Fixes: d179bd1699 ("qed: Acquire/release ptt_ptp lock when enabling/disabling PTP")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output to the RDMA driver whether DPM mode is enabled or disabled in
the HW and if so what is the number of WIDs it supports
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating doorbell BAR partitioning round up the number of
CPUs to the nearest power of 2 so the size of the DPI (per user
section) configured in the hardware will be stored properly and
not truncated.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mechanism to verify RoCE resources are released prior to freeing the
bitmaps. If this is not the case, print what resources were not released.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the posting of the ramrod for the purpose of TID deregistration
fails, abort the deregistration operation without using the FW's
return code.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal RoCE SQE QP state isn't being used. Instead we mark the
QP as in regular error state.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that we're holding a mutex on this error
path. Let's goto exit instead of returning directly.
Fixes: b0bccb69eb ("qed: Change locking scheme for VF channel")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code for acquiring/releasing ptt_ptp lock to ptp specific
implementations i.e., ptp_enable()/disable() respectively.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch deletes the qed_ptp.h file which is not required.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for per-port resource lock in favour of PTP.
PTP module acquires/releases the MFW resource lock while enabling/
disabling the PTP on the interface. The PF instance which has the
ownership of this resource lock will get the exclusive access to the
PTP clock functionality on the port.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds API for default initialization of the MFW resource
locking.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Fixes: b5a9ee7cf3 ("qed: Revise QM configuration")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCBX app_data array is initialized with the incorrect values for
personality field. This would prevent offloaded protocols from
honoring the PFC.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware channel APIs support between
VF and PF for tunnelling configuration for the VFs.
According to that configuration VFs can run VXLAN/GENEVE/GRE
tunnels over it with tunnel features offloaded.
Using these APIs VF can also request for UDP ports configuration
to the PF, although PF and it's child VFs share the same port.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for UDP ports in bulletin board
to notify UDP ports change to the VFs
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tunnel feature offloads based on hw configuration
at initialization time instead of enabling them always.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the tunnel APIs to use per tunnel
info instead of using bitmasks for all tunnels and also
uses single struct to hold the data to prepare multiple
variant of tunnel configuration ramrods to be sent to the hardware.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for static/local dcbx mode. In this mode
adapter brings up the dcbx link with locally configured parameters
instead of performing the dcbx negotiation with the peer. The feature
is useful when peer device/switch doesn't support dcbx.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the older firmware there was no distinction between RoCE and RoCEv2
whereas the newer firmware (8.15.3.0) allows us to configure each
independently. Driver need to populate the RoCEv2 data in its specific
structure.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ieee_setpfc() callback implementation to populate traffic class
count with the user provided value.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed_dcbnl_get_dcbx() API uses kmalloc in GFT_KERNEL mode. The API gets
invoked in the interrupt context by qed_dcbnl_getdcbx callback. Need
to invoke this kmalloc in atomic mode.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PFC error-mask value is not supported by MFW, but this bit could be
set in the pfc bit-map of the operational parameters if remote device
supports it. These operational parameters are used as basis for
populating the dcbx config parameters. User provided configs will be
applied on top of these parameters and then send them to MFW when
requested. Driver need to clear the error-mask bit before sending the
config parameters to MFW.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some adapters may not publish the max_tc value. Populate the default
value for max_tc field in case the mfw didn't provide one.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds necessary APIs to interface with
qede aRFS support in successive patch.
It also reserves separate PTT entry for aRFS,
[as being in fastpath flow] for hardware access instead of
trying to acquire it at run time from the ptt pool.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to maintain the various open archipelagos as a list -
The maximal number of them is known, and we can use the CID
as key for random-access into the array.
Signed-off-by: Michal Kalderon <Michal.Kalderon@caviumc.om>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware can query for some basic iSCSI-related statistics.
Provide those just as we do for other protocols.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that management firmware is capable of telling us the number of CQs
available for a given PF, qed needs to communicate the number to qedi
so it would know have many to use.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware provides a statistic for the number of out-of-order isles
it used - fill it in the iscsi-related statistics.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before initializing the chip's engine, driver currently closes a set
of registers on the HW's ingress flow to prevent packets from slipping
in while they're not supposed to.
This configuration is insufficient, as there are some scenarios where
packets would still arrive even when said registers are set,
but the management firmware already closes other per-port registers
that do suffice, making this setting unnecessray.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default HW configuration is optimal for an architecture where cache
line size is 64B.
During chip initialization, properly initialize the cache line size
in HW to avoid possible redundant PCI transactions.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to access HW registers driver needs to acquire a PTT entry
[mapping between bar memory and internal chip address].
Since acquiring PTT entries could fail [at least in theory] as their
number is finite and other flows can hold them, we reserve special PTT
entries for 'important' enough flows - ones we want to guarantee that
would not be susceptible to such issues.
One such special entry is the 'main' PTT which is meant to be used in
flows such as chip initialization and de-initialization.
However, there are other flows that are also using that same entry
for their own purpose, and might run concurrently with the original
flows [notice that for most cases using the main-ptt by mistake, such
a race is still impossible, at least today].
This patch re-organizes the various functions that currently use the
main_ptt in one of two ways:
- If a function shouldn't use the main_ptt it starts acquiring and
releasing it's own PTT entry and use it instead. Notice if those
functions previously couldn't fail, they now can [as acquisition
might fail].
- Change the prototypes so that the main_ptt would be received as
a parameter [instead of explicitly accessing it].
This prevents the future risk of adding codes that introduces new
use-cases for flows using the main_ptt, ones that might be in race
with the actual 'main' flows.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTT entries are per-hwfn; If some errneous flow is trying
to use a PTT belonging to a differnet hwfn warn user, as this
can break every register accessing flow later and is very hard
to root-cause.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qedr is enabled, qed would try dividing the msi-x vectors between
L2 and RoCE, starting with L2 and providing it with sufficient vectors
for its queues.
Problem is qed would also do that for storage partitions, and as those
don't need queues it would lead qed to award those partitions with 0
msi-x vectors, causing them to believe theye're using INTa and
preventing them from operating.
Fixes: 51ff17251c ("qed: Add support for RoCE hw init")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There seems to be a missing break on the OOO_LB_TC case, pq_id
is being assigned and then re-assigned on the fall through default
case and that seems suspect.
Detected by CoverityScan, CID#1424402 ("Missing break in switch")
Fixes: b5a9ee7cf3 ("qed: Revise QM cofiguration")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be returning -ENOMEM if qed_mcp_cmd_add_elem() fails. The
current code returns success.
Fixes: 4ed1eea82a ("qed: Revise MFW command locking")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible some configurations would prevent driver from utilizing
all the Memory Regions due to a lack of ILT lines.
In such a case, calculate how many memory regions would have to be
dropped due to limit, and manage without those.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As RoCE doesn't need to use the SRC, allocating ILT memory
on behalf of RoCE is wasting available ILT lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of today there's no protocol supported that requires
support from the TM hardware block and enables SRIOV,
but we should still correct the calculation to reflect
the lines required for such future VFs instead of changing
the PF's own lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the HW timers block we should set the number of CIDs
up until the last CID that require timers, instead of only those CIDs
whose protocol needs timers support.
Today, the protocols that require HW timers' support have their CIDs
before any other protocol, but that would change in future [when we
add iWARP support].
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor and clean up the queue manager initialization logic.
Also, this adds support for RoC low latency queues, which later
would be used for improving RoCE latency in high throughput scenarios.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, qed used some port-defined value as BDQ index for both iSCSI
and FCoE.
As management firmware now treats BDQ as a resource and tells each PF
its BDQ-range, start using a valure from that range instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
