When running these commands on DUT (and similar at the other end)
ip link set dev eth0 up
ip link add link eth0 name eth0.10 type vlan id 10
ip addr add 10.0.0.1/24 dev eth0.10
ip link set dev eth0.10 up
ping 10.0.0.2
The ping will fail.
The reason why is failing is because, the network interfaces for lan966x
have a flag saying that the HW can insert the vlan tags into the
frames(NETIF_F_HW_VLAN_CTAG_TX). Meaning that the frames that are
transmitted don't have the vlan tag inside the skb data, but they have
it inside the skb. We already get that vlan tag and put it in the IFH
but the problem is that we don't configure the HW to rewrite the frame
when the interface is in host mode.
The fix consists in actually configuring the HW to insert the vlan tag
if it is different than 0.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Fixes: 6d2c186afa ("net: lan966x: Add vlan support.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250528093619.3738998-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Correct spelling in comments, as flagged by codespell.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20240424-lan743x-confirm-v2-2-f0480542e39f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When vlan filtering is enabled/disabled, it is required to adjust the
maximum received frame size that it can received. When vlan filtering is
enabled, it would all to receive extra 4 bytes, that are the vlan tag.
So the maximum frame size would be 1522 with a vlan tag. If vlan
filtering is disabled then the maximum frame size would be 1518
regardless if there is or not a vlan tag.
Fixes: 6d2c186afa ("net: lan966x: Add vlan support.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend lan966x driver with mdb support by implementing the switchdev
calls: SWITCHDEV_OBJ_ID_PORT_MDB and SWITCHDEV_OBJ_ID_HOST_MDB.
It is allowed to add both ipv4/ipv6 entries and l2 entries. To add
ipv4/ipv6 entries is not required to use the PGID table while for l2
entries it is required. The PGID table is much smaller than MAC table
so only fewer l2 entries can be added.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend lan966x driver with fdb support by implementing the switchdev
calls SWITCHDEV_FDB_ADD_TO_DEVICE and SWITCHDEV_FDB_DEL_TO_DEVICE.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the driver to support vlan filtering by implementing the
switchdev calls SWITCHDEV_OBJ_ID_PORT_VLAN,
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
