Depmod reports a cyclic dependency between modules sparx5-switch.ko and
lan969x-switch.ko:
depmod: ERROR: Cycle detected: lan969x_switch -> sparx5_switch -> lan969x_switch
depmod: ERROR: Found 2 modules in dependency cycles!
make[2]: *** [scripts/Makefile.modinst:132: depmod] Error 1
make: *** [Makefile:224: __sub-make] Error 2
This makes sense, as they both require symbols from each other.
Fix this by compiling lan969x support into the sparx5-switch.ko module.
In order to do this, in a sensible way, we move the lan969x/ dir into
the sparx5/ dir and do some code cleanup of code that is no longer
required.
After this patch, depmod will no longer complain, as lan969x support is
compiled into the sparx5-swicth.ko module, and can no longer be compiled
as a standalone module.
Fixes: 98a0111960 ("net: sparx5: add compatible string for lan969x")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add match data for lan969x, with initial fields for iomap, iomap_size
and ioranges. Add new Kconfig symbol CONFIG_LAN969X_CONFIG for compiling
the lan969x driver.
It has been decided to give lan969x its own Kconfig symbol, as a
considerable amount of code is needed, beside the Sparx5 code, to add
full chip support (and more will be added in future series). Also this
makes it possible to compile Sparx5 without lan969x.
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241024-sparx5-lan969x-switch-driver-2-v2-6-a0b5fae88a0f@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The LAN8650/1 is designed to conform to the OPEN Alliance 10BASE-T1x
MAC-PHY Serial Interface specification, Version 1.1. The IEEE Clause 4
MAC integration provides the low pin count standard SPI interface to any
microcontroller therefore providing Ethernet functionality without
requiring MAC integration within the microcontroller. The LAN8650/1
operates as an SPI client supporting SCLK clock rates up to a maximum of
25 MHz. This SPI interface supports the transfer of both data (Ethernet
frames) and control (register access).
By default, the chunk data payload is 64 bytes in size. The Ethernet
Media Access Controller (MAC) module implements a 10 Mbps half duplex
Ethernet MAC, compatible with the IEEE 802.3 standard. 10BASE-T1S
physical layer transceiver integrated is into the LAN8650/1. The PHY and
MAC are connected via an internal Media Independent Interface (MII).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Link: https://patch.msgid.link/20240909082514.262942-14-Parthiban.Veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new FDMA library for interacting with the FDMA engine on Microchip
Sparx5 and lan966x switch chips, in an effort to reduce duplicate code
and provide a common set of symbols and functions.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds initial TC flower filter support to Sparx5 for the IS2 VCAP.
The support consists of the source and destination MAC addresses,
and the trap and pass actions.
This is how you can create a rule that test the functionality:
tc qdisc add dev eth0 clsact
tc filter add dev eth0 ingress chain 8000000 prio 10 handle 10 \
protocol all flower skip_sw \
dst_mac 0a:0b:0c:0d:0e:0f \
src_mac 2:0:0:0:0:1 \
action trap
The IS2 chains in Sparx5 are assigned like this:
- chain 8000000: IS2 Lookup 0
- chain 8100000: IS2 Lookup 1
- chain 8200000: IS2 Lookup 2
- chain 8300000: IS2 Lookup 3
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Tested-by: Casper Andersson <casper.casan@gmail.com>
Reviewed-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic SwitchDev driver framework for lan966x. It
includes only the IO range mapping and probing of the switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the Sparx5 basic SwitchDev driver framework with IO range
mapping, switch device detection and core clock configuration.
Support for ports, phylink, netdev, mactable etc. are in the following
patches.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PTP support includes:
Ingress, and egress timestamping.
One step timestamping available.
PTP clock support.
Periodic output support.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool get_drvinfo
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add main source files for new lan743x driver
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ethernet driver supports the Micorchip enc424j600/626j600 Ethernet
controller over a SPI bus interface. This driver makes use of the regmap API to
optimize access to registers by caching registers where possible.
Datasheet:
http://ww1.microchip.com/downloads/en/DeviceDoc/39935b.pdf
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ethernet driver supports the Micorchip enc424j600/626j600 Ethernet
controller over a SPI bus interface. This driver makes use of the regmap API to
optimize access to registers by caching registers where possible.
Datasheet:
http://ww1.microchip.com/downloads/en/DeviceDoc/39935b.pdf
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Microchip driver into drivers/net/ethernet/microchip/ and
make the necessary Kconfig and Makefile changes.
CC: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
