drivers/net/ethernet/mellanox/mlxsw//spectrum.c:251:28: warning: symbol
'mlxsw_sp_span_entry_find' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:265:28: warning: symbol
'mlxsw_sp_span_entry_get' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:367:56: warning: mixing
different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:367:56: int enum
mlxsw_sp_span_type versus
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:367:56: int enum
mlxsw_reg_mpar_i_e
...
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:598:32: warning:
mixing different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:598:32: int
enum mlxsw_reg_sbxx_dir versus
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:598:32: int
enum devlink_sb_pool_type
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:600:39: warning:
mixing different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:600:39: int
enum mlxsw_reg_sbpr_mode versus
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:600:39: int
enum devlink_sb_threshold_type
...
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:255:54: warning:
mixing different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:255:54: int
enum mlxsw_sp_l3proto versus
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:255:54: int
enum mlxsw_reg_ralxx_protocol
...
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1749:6: warning:
symbol 'mlxsw_sp_fib_entry_put' was not declared. Should it be static?
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default statistics ndo to return HW statistics
(like the one returned by ethtool_ops).
The HW stats are collected to a cache by delayed work every 1 sec.
Implement the offload stat ndo.
Add a function to get SW statistics, to be called from this function.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the deprecated {get,set}_settings callbacks and instead add
{get,set}_link_ksettings along with support for newly available speeds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device can support multiple port types, so don't return on first
match.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case port isn't operational we shouldn't report the port type, but
instead return PORT_OTHER. This is consistent with most other drivers
that return PORT_OTHER when media type can't be determined.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If autonegotiation was performed successfully, then we should report the
link partner's advertised speeds instead of the operational speed of the
port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the device always reported autonegotiation to be off
although it was on by default.
Allow the user to disable / enable autonegotiation and report its status
correctly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
During port init, we currently set the port's type to Ethernet after
setting its MAC address. However, the hardware documentation states this
should be the other way around.
Align the driver with the hardware documentation and set the port's MAC
address after setting its type.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the notifier is registered for every asic instance, however the
same block. Fix this by moving the registration to module init.
Fixes: c723c735fa ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of trapping certain packets to the CPU and then relying on it to
flood them we can instead make the device mirror them.
The following packet types are mirrored:
* DHCP: Broadcast packets that should be flooded by the device, but also
trapped in case CPU is running the DHCP server.
* IGMP query: Multicast packets that need to be forwarded to other
bridge ports, but also trapped so that receiving netdev will be marked
as a router port by the bridge driver.
* ARP request: Broadcast packets that should be forwarded to other
bridge ports, but also trapped in case requested IP is of the local
machine.
* ARP response: Unicast packets that should be forwarded by the bridge
but also trapped in case response is directed at us.
Set the trap action of such packets to mirror and mark them using
'offload_fwd_mark' to prevent the bridge driver from forwarding them
itself.
Note that OSPF packets are also marked despite their action being trap.
The reason for this is that the device traps such packets in the
pipeline after they were already flooded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we only trapped packets to CPU, but we are going to allow
some packets to be mirrored (trap & forward) to CPU.
Extend the Rx listener with 'action' member.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of copying & pasting the same struct initialization for every
Rx listener, just use a macro.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 99724c18fc ("mlxsw: spectrum: Introduce support for
router interfaces") we used to assign vFIDs to the created vPorts. Since
these vPorts were used for slow path traffic we had to disable learning
for them, as it doesn't make sense to have it enabled.
This is no longer the case and now vPorts are either used for router
interfaces (for which learning is disabled by the firmware) or bridge
ports (for which learning is explicitly enabled by the driver).
Therefore, we can remove the learning configuration upon vPort creation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to prevent the device from generating learning
notifications for a port that was configured with learning disabled.
Since learning configuration is done per {Port, VID} we need to apply
the port's learning configuration for any VID that is added to the
bridge port's VLAN filter list.
When a VID is added to the VLAN filter list of a VLAN-aware bridge port,
configure the {Port, VID} learning status according to the port's
configuration. When the VID is removed, disable learning for the {Port,
VID}.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we have a layer 3 interface on top of a bridge (VLAN / FID RIF),
then we should flood the following packet types to the router:
* Broadcast: If DIP is the broadcast address of the interface, then we
need to be able to get it to CPU by trapping it following route lookup.
* Reserved IP multicast (224.0.0.X): Some control packets (e.g. OSPF)
use this range and are trapped in the router block.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.
The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.
Fixes: a85a970af2 ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While going over the code I noticed we are missing two rollbacks in the
port's creation error path. Add them and adjust the place of one of them
in the port's removal sequence so that both are symmetric.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the conditions to generate an ICMP Redirect Message is that "the
packet is being forwarded out the same physical interface that it was
received from" (RFC 1812).
Therefore, we need to be able to trap such packets and let the kernel
decide what to do with them.
For each RIF, enable the loop-back filter, which will raise the LBERROR
trap whenever the ingress RIF equals the egress RIF.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Reported-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following traps:
1) MTU Error: Trap packets whose size is bigger than the egress RIF's
MTU. If DF bit isn't set, traffic will continue to be routed in slow
path.
2) TTL Error: Trap packets whose TTL expired. This allows traceroute to
work properly.
3) OSPF packets.
Fixes: 7b27ce7bb9 ("mlxsw: spectrum: Add traps needed for router implementation")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of
init sequence") moved ports initialization to the end of the init
sequence, which means ports are the first to be removed during fini.
Since the FDB delayed work is still active when ports are removed it's
possible for it to process FDB notifications of inactive ports,
resulting in a warning message.
Fix that by marking ports as inactive only after unregistering them. The
NETDEV_UNREGISTER event will invoke bridge's driver port removal
sequence that will cause the FDB (and FDB notifications) to be flushed.
Fixes: bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of init sequence")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when device configuration fails we emit errors to the kernel
log despite the fact we already get these from the EMAD transaction
layer, so remove them.
In addition to being unnecessary, removing these error messages will
allow us to reuse mlxsw_sp_port_add_vid() to create the PVID vPort
before registering the netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VLAN filter from the device we shouldn't return upon the
first error we encounter, as otherwise we'll have resources that will
never be freed nor used.
Instead, we should keep trying to free as much resources as possible in
a best effort mode.
Remove the error message as well, since we already get these from the
EMAD transaction code.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We correctly execute mlxsw_sp_port_dcb_fini() when port is removed, but
I missed its rollback in the error path of port creation, so add it.
Fixes: f00817df2b ("mlxsw: spectrum: Introduce support for Data Center Bridging (DCB)")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_CLS_ACT isn't set 'struct tcf_exts' has no member named
'actions' and we therefore must not access it. Otherwise compilation
fails.
Fix this by introducing a new macro similar to tc_no_actions(), which
always returns 'false' if CONFIG_NET_CLS_ACT isn't set.
Fixes: 763b4b70af ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch offloads port mirroring directives to hw using the matchall TC
with action mirror. It includes both the implementation of the
ndo_setup_tc function for the spectrum driver and the spectrum hardware
offload configuration code.
The hardware offload code is basically two new functions which are capable
of adding and removing a new mirror ports pair. It is done using the MPAT,
MPAR and SBIB registers:
- A new Switch-Port Analyzer (SPAN) entry is added using MPAT to the 'to'
port.
- The 'to' port is bound to the SPAN entry using MPAR register.
- In case of egress SPAN, the 'to' port gets a new internal shared
buffer using SBIB register.
In addition, a new database was added to the mlxsw_sp struct to store all
the SPAN entries and their bound ports list. The number of supported SPAN
entries is determined by resource query.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add resources query implementation. If exists, query the HW for its
builtin resources instead of having them as consts in the code.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the transmit queue length of each traffic class and the amount of
unicast packets discarded due to insufficient room in the shared buffer.
The first counter allows us to debug user priority to traffic class
mapping, whereas the drop counter is useful when determining shared buffer
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose per-priority bytes / packets / PFC packets counters via ethtool.
These counters are very useful when debugging QoS functionality and
provide a better insight into the device's forwarding plane.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device supports link autonegotiation, so let the user know about it
by indicating support via ethtool ops.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a new speed we need to disable and enable the port for the
changes to take effect. We currently only do that if the operational
state of the port is up. However, setting a new speed following link
training failure will require us to explicitly set the port down and then
up.
Instead, disable and enable the port based on its administrative state.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Override the defaults and define the area sizes ourselves.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to hold some private data for every neigh entry. It would be
possible to do it using neigh_priv_len/ndo_neigh_construct/
ndo_neigh_destroy however only for the port device itself. That would not
work for stacked devices like bridge/team/bond. So introduce a private
neigh table. Hook onto ndos neigh_construct/destroy and add/remove
table entry according to that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with the previously introduced L3 interfaces, listen to 'inetaddr'
notifications sent for bridges devices configured on top of the port
netdevs and create / destroy router interfaces (RIFs) accordingly.
This also includes VLAN devices configured on top of the VLAN-aware
bridge.
The RIFs will be destroyed either when the last IP address is removed or
when the underlying FID is is destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before introducing support for L3 interfaces on top of the VLAN-aware
bridge we need to add some missing infrastructure.
Such an interface can either be the bridge device itself or a VLAN
device on top of it. In the first case the router interface (RIF) is
associated with FID 1, which is created whenever the first port netdev
joins the bridge. We currently assume the default PVID is 1 and that
it's already created, as it seems reasonable. This can be extended in
the future.
However, in the second case it's entirely possible we've yet to create a
matching FID. This can happen if the VLAN device was configured before
making any bridge port member in the VLAN.
Prevent such ordering problems by using the VLAN device's CHANGEUPPER
event to configure the FID. Make the VLAN device hold a reference to the
FID and prevent it from being destroyed even if none of the port netdevs
is using it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit deprecated the vFIDs used to get traffic to the CPU
('port_vfids'). Thus, we now use the vFIDs as god intended and the
artificial split is no longer needed.
Rename functions and variables to reflect that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we only supported bridged interfaces. Packets ingressing
through the switch ports were either classified to FIDs (in the case of
the VLAN-aware bridge) or vFIDs (in the case of VLAN-unaware bridges).
The packets were then forwarded according to the FDB. Routing was done
entirely in slowpath, by splitting the vFID range in two and using the
lower 0.5K vFIDs as dummy bridges that simply flooded all incoming
traffic to the CPU.
Instead, allow packets to be routed in the device by creating router
interfaces (RIFs) that will direct them to the router block.
Specifically, the RIFs introduced here are Sub-port RIFs used for VLAN
devices and port netdevs. Packets ingressing from the {Port / LAG ID, VID}
with which the RIF was programmed with will be assigned to a special
kind of FIDs called rFIDs and from there directed to the router.
Create a RIF whenever the first IPv4 address was programmed on a VLAN /
LAG / port netdev. Destroy it upon removal of the last IPv4 address.
Receive these notifications by registering for the 'inetaddr'
notification chain. A non-zero (10) priority is used for the
notification block, so that RIFs will be created before routes are
offloaded via FIB code.
Note that another trigger for RIF destruction are CHANGEUPPER
notifications causing the underlying FID's reference count to go down to
zero. This can happen, for example, when a VLAN netdev with an IP address
is put under bridge. While this configuration doesn't make sense it does
cause the device and the kernel to get out of sync when the netdev is
unbridged. We intend to address this in the future, hopefully in current
cycle.
Finally, Remove the lower 0.5K vFIDs, as they are deprecated by the RIFs,
which will trap packets according to their DIP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are just about to introduce router interfaces (RIFs), but before that
we need to be able update the device with the correct RIF attributes
whenever they change for the netdev the RIF is backing. Two such
attributes are MTU and MAC.
The MAC is used both to set the source MAC of packets egressing from the
RIF and also to program an FDB rule that will direct packets to the
router block.
Use the existing netdevice notification block and respond to CHANGEADDR
and CHANGEMTU accordingly. Store both attributes in the RIF struct
in case we need to revert to old attributes following a failed update.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.
Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip2me:
To instruct HW to send trapped ip2me traffic to kernel, we have to add
this trap. Selection ip2me traffic is introduced later on in this set.
ARPs:
We are going to stop flooding to CPU port when netdev isn't bridged and
only get packets destined to the netdev's IP address and certain control
packets.
Add traps for ARP request (broadcast) and response (unicast) in order to
get these to the CPU and resolve neighbours.
host miss:
If a packet is routed through a directly connected route and its
destination IP is not in the device's neighbour table, then we need to
trap it to CPU. This will cause the host to resolve the MAC of the
neighbour, which will be eventually programmed to the device's table.
router ingress:
In order to trap packets in router part.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing packet traps we should use action 'discard' instead of
'forward', as some trap IDs we'll add cannot be configured with the
later. However, result is the same, as packets are not trapped to the
CPU.
In the future we will be able to reverse the operation properly by
detaching the trap group from the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling the router in the device we will represent L3 netdevs
using router interfaces (RIFs). These will be specified whenever
programming routes or neighbours on the netdev.
Introduce the basic RIF infrastructure which allows one to lookup a RIF
by its netdev. Later patches in the series will extend this, but the
basic routines are needed now in order to direct traffic to CPU.
Pointers to the RIF structs are stored in an array indexed by the RIF's
number. This will allow us to efficiently update the kernel's neighbour
table when regularly dumping the device's table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a skeleton router file and do basic HW initialization of router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During ports initialization a net device is registered for each
available port, which implies the port is usable. However, a port is
only usable after the different parts of the device (e.g. flooding,
buffers) are initialized. This is especially important now, when we must
initialize the router before the ports, as otherwise the device can't be
initialized.
Solve that by initializing the switch ports at the end of init sequence.
Also, remove an unnecessary warning about port up/down events, which
would otherwise be invoked whenever removing the driver, as ports are
removed before unregistering the listener for these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to assign router interfaces (RIFs) to netdevs if an IPv4
address was assigned to them. If one was assigned to a port netdev, this
will translate to the PVID vPort being member in a RIF.
While it's possible for a LAG slave to have an IP address, we can't have
a vPort being member in two FIDs (assuming the LAG device will be
put in bridge / assigned an IP address).
Solve that by making the PVID vPort leave any FID it might be a member
in when joining / leaving LAG.
Note that the PVID vPort is the only vPort that can be present on the
port when it's put under LAG.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN devices are created on top of LAG, their underlying vPorts are
configured correctly with LAG membership.
However, the PVID vPort is implicit and already present when the port
netdev is put under LAG, so its LAG membership is never set. Set it
correctly when joining / leaving LAG.
This didn't matter until now, but we are going to introduce support for
router interfaces (RIFs), which need to take into account LAG membership.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port isn't bridged it is still possible to invoke switchdev ops and
configure the device's VLAN filters.
However, this will require us to use different Router InterFaces (RIFs)
for the same netdev, instead of one per-netdev as with any other
configuration.
Taking the above into account and the fact that this functionality is
questionable with regards to the device's normal use-case, remove it and
instead return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port netdevs (e.g. swXpY) that are not bridged are represented in the
device using a vPort with VID=PVID=1 (the PVID vPort), as untagged
packets entering the switch are internally tagged with the PVID VLAN.
When these packets are routed through a different port netdev they
should egress untagged.
This wasn't a problem until now, as non-bridged traffic only originated
from the CPU, which transmits packets out of the port as-is.
When a vPort is created with VID 1 mark it as egress untagged.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug purposes, it's useful to know the order in which the driver
responds to changes in the topology of its upper devices.
Add debug prints to signal these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are situations in which a vPort is destroyed while still holding
references to device's resources such as FIDs and FDB records. This can
happen, for example, when a VLAN device is deleted while still being
bridged.
Instead of trying to make sure vPort destruction is invoked when it no
longer uses device's resources, just free them upon destruction. This
simplifies the code, as we no longer need to take different situations
into account when events are received - cleanup is taken care of in one
place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB entries are learned using {Port / LAG ID, FID} and therefore should
be flushed whenever a port (vPort) leaves its FID (vFID).
However, when the bridge port is a LAG device (or a VLAN device on top),
then FDB flushing is conditional. Ports removed from such LAG
configurations must not trigger flushing, as other ports might still be
members in the LAG and therefore the bridge port is still active.
The decision whether to flush or not was previously computed in the
netdevice notification block, but in order to flush the entries when a
port leaves its FID this decision should be computed there.
Strip the notification block from this logic and instead move it to one
FDB flushing function that is invoked from both the FID / vFID leave
functions.
When port isn't member in LAG, FDB flushing should always occur.
Otherwise, it should occur only when the last port (vPort) member in the
LAG leaves the FID (vFID).
This will allow us - in the next patch - to simplify the cleanup code
paths that are hit whenever the topology above the port netdevs changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all vPorts will have FIDs assigned to them, so make sure functions
first test for FID presence.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, not all vPorts will be assigned FIDs, so instead
of returning the FID index of a vPort, return a pointer to its FID
struct. This will allow us to know whether it's legal to access the
vPort's FID parameters such as index and device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a very similar way to the vFIDs, make the first 4K FIDs - used in the
VLAN-aware bridge - use the new FID struct.
Upon first use of the FID by any of the ports do the following:
1) Create the FID
2) Setup a matching flooding entry
3) Create a mapping for the FID
Unlike vFIDs, upon creation of a FID we always create a global
VID-to-FID mapping, so that ports without upper vPorts can use it
instead of creating an explicit {Port, VID} to FID mapping.
When a port leaves a FID the reverse is performed. Whenever the FID's
reference count reaches zero the FID is deleted along with the global
mapping.
The per-FID struct will later allow us to configure L3 interfaces on top
of the VLAN-aware bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vPort is created or when it joins a bridge we always do the same
set of operations:
1) Create the vFID, if not already created
2) Setup flooding for the vFID
3) Map the {Port, VID} to the vFID
When a vPort is destroyed or when it leaves a bridge the reverse is
performed.
Encapsulate the above in join / leave functions and simplify the code.
FIDs and rFIDs will use a similar set of functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had a dedicated struct only for vFIDs, but before
introducing support for L3 interfaces we need to make it generic and
use it for all three types of FIDs:
1) FIDs - 0..4K-1, used for the VLAN-aware bridge
2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges
3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in
the device. Will be introduced later in the series.
The three types of L3 interfaces - Router InterFaces, RIFs - that will
be introduced correspond to the three types of FIDs and are configured
using them. Therefore, we'll need to store the links between them as
well as a reference count on the underlying FID, so that the
corresponding RIF will be destroyed when it reaches zero.
Note that the lower 0.5K vFIDs are currently used for for non-bridged
netdevs, so that traffic could be flooded to the CPU port. However, when
rFIDs will be introduced we'll no longer need these and they too will be
used for VLAN-unaware bridges.
Make the vFID struct generic by renaming it and some of its fields. FIDs
will be converted to use it later in the series.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a FID index instead of vFID and ease the transition towards a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FID used by a vPort (vFID, but also rFID later in the series) is
always mapped using {Port, VID} and not only VID as with the 4K FIDs of
the VLAN-aware bridge.
Instead of specifying all the arguments each time, just wrap this
operation using a dedicated function and simplify the code.
As before, the function takes FID as its argument in preparation for a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and use only one function for vFID creation /
destruction.
Unlike before, the function receives a FID index as its argument and not
a vFID index. Instead of passing 0, now one would need to pass 4K, which
is the first vFID.
This is the first step in creating a generic FID struct that will be
used for all three types of FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all call sites 'only_uc' is set to false, so strip it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We hold a reference count on the number of ports member in the
VLAN-aware bridge, as we only support one.
Instead of always incrementing / decrementing the reference count after
joining / leaving the bridge, simply do this accounting in the join /
leave functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument 'br_dev' is never used, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When responding to unlinking CHANGEUPPER notifications we shouldn't
return any value, as it's not checked by upper layers.
In addition, there's nothing the driver can do in case of failure, so it
should simply continue and try to free as much resources as possible and
not stop on first error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking for a condition and then issue the warning, just do
it in one go and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When upper device of a VLAN device changes we already made sure it's
a bridge device in PRECHANGEUPPER, so no need to check it's a master
device in CHANGEUPPER.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port netdev is put under LAG it cannot have VLAN upper devices,
so forbid that. The LAG device itself can have VLAN upper devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only support the following upper devices for port netdevs:
1) Bridge
2) LAG (bond / team)
3) VLAN
Any other device is forbidden, so return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking the error value and returning NOTIFY_BAD, just use
notifier_from_errno() and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the SW TX counter from counting the TX header bytes
since they are not being sent out.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rtnl_fill_ifinfo() is called for a certain netdevice it queries its
various parameters such as switch id and physical port name. The
function might get called in an atomic context, which means the
underlying driver must not sleep during the query operation.
Don't query the device and sleep during ndo_get_phys_port_name(), but
instead store the needed parameters in port creation time.
Fixes: 2bf9a58675 ("mlxsw: spectrum: Add support for physical port names")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is created following a split / unsplit we need to map it to
the correct module and lane, enable it and then continue to initialize
its various parameters such as MTU and VLAN filters.
Under certain conditions, such as trying to split ports at the bottom
row of the front panel by four, we get firmware errors.
After evaluating this with the firmware team it was decided to alter the
split / unsplit flow, so that first all the affected ports are mapped,
then enabled and finally each is initialized separately.
Fix the split / unsplit flow by first mapping and enabling all the
affected ports. Newer firmware versions will support both flows.
Fixes: 18f1e70c41 ("mlxsw: spectrum: Introduce port splitting")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the leave procedure in the error path symmetric to the join
procedure and first remove the port from the collector before
potentially destroying the LAG.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement occupancy API introduced in devlink and mlxsw core. This is
done by accessing SBPM register for Port-Pool and SBSR for Port-TC
current and max occupancy values. Max clear is implemented using the
same registers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement previously introduced mlxsw core shared buffer API.
For Spectrum, that is done utilizing registers SBPR, SBCM and SBPM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of that, pass mlxsw_core and use a helper to get driver priv
from driver code. Looks much cleaner that way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing around driver priv, pass struct mlxsw_core *
directly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove devlink port reg/unreg from spectrum and switchx2 code and rather
do the common work in core. That also ensures code separation where
devlink is only used in core.c.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the appropriate DCB ops and allow a user to configure certain
traffic classes as lossless.
The operation configures PFC for both the egress (respecting PFC frames)
and ingress (sending PFC frames) parts of the port.
At egress, when a PFC frame is received for a PFC enabled priority, then
all the priorities mapped to the same TC are stopped.
At ingress, the priority group (PG) buffers to which the enabled PFC
priorities are mapped are configured to be lossless. PFC frames will be
transmitted when the Xoff threshold is crossed.
The user-supplied delay parameter is used to determine the PG's size
according to the following formula:
PG_SIZE = PG_SIZE_LOSSY + delay * CELL_FACTOR + MTU
In the worst case scenario the delay will be made up of packets that
are all of size CELL_SIZE + 1, which means each packet will require
almost twice its true size when buffered in the switch. We therefore
multiply this value by the "cell factor", which is close to 2.
Another MTU is added in case the transmitting host already started
transmitting a maximum length frame when the PFC packet was received.
As with PAUSE enabled ports, when the port's MTU is changed both the
PGs' size and threshold are adjusted accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to add support for PFC as part of DCB ops, which requires us
to report the number of PFC frames sent and received per priority.
Add per priority counters in order to report number of PFC frames sent
and received per priority.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet ingress the switch it's placed in its assigned priority
group (PG) buffer in the port's headroom buffer while it goes through
the switch's pipeline. After going through the pipeline - which
determines its egress port(s) and traffic class - it's moved to the
switch's shared buffer awaiting transmission.
However, some packets are not eligible to enter the shared buffer due to
exceeded quotas or insufficient space. Marking their associated PGs as
lossless will cause the packets to accumulate in the PG buffer. Another
reason for packets accumulation are complicated pipelines (e.g.
involving a lot of ACLs).
To prevent packets from being dropped a user can enable PAUSE frames on
the port. This will mark all the active PGs as lossless and set their
size according to the maximum delay, as it's not configured by user.
+----------------+ +
| | |
| | |
| | |
| | |
| | |
| | | Delay
| | |
| | |
| | |
| | |
| | |
Xon/Xoff threshold +----------------+ +
| | |
| | | 2 * MTU
| | |
+----------------+ +
The delay (612 [Cells]) was calculated according to worst-case scenario
involving maximum MTU and 100m cables.
After marking the PGs as lossless the device is configured to respect
incoming PAUSE frames (Rx PAUSE) and generate PAUSE frames (Tx PAUSE)
according to user's settings.
Whenever the port's headroom configuration changes we take into account
the PAUSE configuration, so that we correctly set the PG's type (lossy /
lossless), size and threshold. This can happen when:
a) The port's MTU changes, as it directly affects the PG's size.
b) A PG is created following user configuration, by binding a priority
to it.
Note that the relevant SUPPORTED flags were already mistakenly set by
the driver before this commit.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to set maximum rate for a particular TC using DCB ops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the appropriate DCB ops and allow a user to configure:
* Priority to traffic class (TC) mapping with a total of 8
supported TCs
* Transmission selection algorithm (TSA) for each TC and the
corresponding weights in case of weighted round robin (WRR)
As previously explained, we treat the priority group (PG) buffer in the
port's headroom as the ingress counterpart of the egress TC. Therefore,
when a certain priority to TC mapping is configured, we also configure
the port's headroom buffer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic infrastructure for DCB and add the missing ops in
following patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before introducing support for DCB ops we should first make sure we
initialize the relevant parts in the device correctly. Specifically, the
egress scheduling.
The device supports a superset of the 802.1Qaz standard with 4 hierarchy
levels that can be linked to each other in multiple ways and with
different transmission selection algorithms (TSA) employed between them.
However, since we only intend to support the 802.1Qaz standard we
flatten the hierarchies and let the user configure via DCB ops the TSA
and max rate shaper at the subgroup hierarchy (see figure below) and the
mapping between switch priority to traffic class. By default, all switch
priorities are mapped to traffic class 0, strict priority is employed
and max shaper is disabled.
Default configuration:
switch priority 0 ... switch priority 7
+ +
| |
+----------------------------------+
|
+--v--+ +-----+
Traffic Class | | | |
Hierarchy | TC0 | ... | TC7 |
| | | |
+--+--+ +--+--+
| |
+--v--+ +--v--+
Subgroup | SG0 | | SG7 |
Hierarchy | | | |
+-----+ +-----+
| TSA | | TSA |
+-----+ ... +-----+
| MAX | | MAX |
+--+--+ +--+--+
| |
+---------------+----------------+
|
+--v--+
Group | |
Hierarchy | GR0 |
| |
+--+--+
|
+--v--+
Port | |
Hierarchy | PR0 |
| |
+-----+
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets ingress the switch they are assigned a switch priority and
directed to the corresponding priority group (PG) buffer in the port's
headroom buffer.
Since we now map all switch priorities to priority group 0 (PG0) by
default, there is no need to allocate the other priority groups during
initialization. The only exception is PG9, which is used for control
traffic.
At minimum, the PG should be able to store the currently classified
packet (pipeline latency isn't 0) and also the packets arriving during
the classification time. However, an incoming packet will not be
buffered if there is no available MTU-sized buffer space for storing it.
The buffer needed to accommodate for pipeline latency is variable and
needs to take into account both the current link speed and current
latency of the pipeline, which is time-dependent. Testing showed that
setting the PG's size to twice the current MTU is optimal.
Since PG9 is used strictly for control packets and not subject to flow
control, we are not going to resize it according to user configuration,
so we simply set it according to worst case scenario, which is twice the
maximum MTU.
In any case, later patches in the series will allow a user to direct
lossless flows to other PGs than PG0 and set their size to accommodate
for round-trip propagation delay.
The above change also requires us to resize the PG buffer whenever the
port's MTU is changed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export to userspace the front panel name of the port, so that udev can
rename the ports accordingly. The convention suggested by switchdev
documentation is used:
1) Non-split: pX
2) Split: pXsY
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we only support one VLAN filtering bridge we need to associate a
reference count with it, so that when the last port netdev leaves it, we
would know that a different bridge can be offloaded to hardware.
When a LAG device is memeber in a bridge and port netdevs are leaving
the LAG, we should always decrement the bridge's reference count, as it's
incremented for any port in the LAG.
Fixes: 4dc236c317 ("mlxsw: spectrum: Handle port leaving LAG while bridged")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to split or unsplit a port using the newly introduced
devlink ops.
Once split, the original netdev is destroyed and 2 or 4 others are
created, according to user configuration. The new ports are like any
other port, with the sole difference of supporting a lower maximum
speed. When unsplit, the reverse process takes place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting and unsplitting we'll destroy usable ports on the fly, so
mark them using a NULL pointer to indicate that their local port number
is free and can be re-used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port netdevs are each associated with a different local port number
in the device. These local ports are grouped into groups of 4 (e.g.
(1-4), (5-8)) called clusters. The cluster constitutes the one of two
possible modules they can be mapped to. This mapping is board-specific
and done by the device's firmware during init.
When splitting a port by 4, the device requires us to first unmap all
the ports in the cluster and then map each to a single lane in the module
associated with the port netdev used as the handle for the operation.
This means that two port netdevs will disappear, as only 100Gb/s (4
lanes) ports can be split and we are guaranteed to have two of these
((1, 3), (5, 7) etc.) in a cluster.
When unsplit occurs we need to reinstantiate the two original 100Gb/s
ports and map each to its origianl module. Therefore, during driver init
store the initial local port to module mapping, so it can be used later
during unsplitting.
Note that a by 2 split doesn't require us to store the mapping, as we
only need to reinstantiate one port whose module is known.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a port we replace it with 2 or 4 other ports. To be able
to do that we need to remove the original port netdev and unmap it from
its module. However, we first mark it as disabled, as active ports
cannot be unmapped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PVID is toggled off on a port member in a VLAN filtering bridge or
the PVID VLAN is deleted, make the port drop untagged packets. Reverse
the operation when PVID is toggled back on.
Set the PVID back to the default (1), when leaving the bridge so that
untagged traffic will be directed to the CPU.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN device leaves a bridge its STP state is set to DISABLED,
which causes the hardware to discard any packets coming through the port
with this VLAN.
Fix that by setting STP state to FORWARDING when the device leaves its
bridge and allow traffic to be directed to CPU.
Fixes: 26f0e7fb15 ("mlxsw: spectrum: Add support for VLAN devices bridging")
Reported-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in previous commit, we should always take care of flushing
the FDB in the driver and not rely on bridge code.
We need to distinguish between two cases with regards to LAG:
1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of
it). In this case don't flush the FDB entries pointing to the LAG ID, as
this will affect other ports still member in the LAG. Only flush the FDB
when the last port in the LAG is leaving the bridge.
2) LAG device is leaving the bridge. In this case the CHANGEUPPER event
is simply propagated to each member port, so make each port flush the
FDB in its turn.
Note that emptying a bridged LAG from ports creates an inconsistency
between hardware and software. A user who later (< ageing_time)
re-populates the LAG won't have any FDB entries pointing to the LAG ID
in hardware, but they will be present in the software bridge's FDB.
Currently there is no good solution to this problem, but this will be
addressed by us in the future.
In order to optimize the flushing process, flush by port or LAG ID if
there are no VLAN interfaces on top of the port. Otherwise, flush using
(Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of
VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to
which the VLAN device is mapped to.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a user to remove a port from a LAG device, while the
LAG device or VLAN devices on top of it are bridged. In these cases,
bridge's teardown sequence is never issued, so we need to take care of
it ourselves.
When LAG's unlinking event is received by port netdev:
1) Traverse its vPorts list and make those member in a bridge leave it.
They will be deleted later by LAG code.
2) Make the port netdev itself leave its bridge if member in one.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SWITCHDEV_OBJ_ID_PORT_MDB switchdev ops support. On first MDB insertion
creates a new multicast group (MID) and add members port to the MID. Also
add new MDB entry for the flooding-domain (fid-vid) and link the MDB entry
to the newly constructed MC group.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vlan is been configured, remeber the untagged mode of the vlan.
When displaying the list of configured VLANs, show the untagged attribute.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge port attributes are offloaded to hardware when invoked with SELF
flag set, but it really makes no sense to reflect them when port is not
bridged.
Allow a user to change these attribute only when port is bridged and
initialize them correctly when joining or leaving a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the bridge status of physical ports in the appropriate functions, to
be consistent with LAG join/leave and vPorts joining/leaving bridge.
Also, remove the error messages in these two functions, as we already
emit errors in both the single functions they call.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for us to fail when joining or leaving a bridge, so let
the user know about that by returning NOTIFY_BAD, as already done for
LAG join/leave and 802.1D bridges.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set PVID to 1 in mlxsw_sp_port_vlan_init(), so we can remove this
statement.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a VLAN device on top of LAG, we are basically creating a
vPort on top of each of the port netdevs member in the LAG. Therefore,
these vPorts should inherit both the LAG status and LAG ID from the
underlying port netdevs.
In addition, when the VLAN device joins or leaves a bridge each of the
underlying vPorts should know about it and act accordingly. This is
achieved by propagating the VLAN event down to the lower devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the member VLAN devices in a bridge need to share the same vFID.
To achieve that, expand the vFID struct to include the associated bridge
device (or lack of) and allow one to lookup a vFID based on a bridge
device.
When joining a bridge, lookup the relevant vFID or create one if none
exists. Next, make the VLAN device use the vFID.
Leaving a bridge can either occur because a user removed the VLAN device
from a bridge or because the VLAN device was deleted by the user. In the
latter case the bridge's teardown sequence is invoked after the hardware
vPort is already gone. Therefore, when unlinking the VLAN device from
the real device, check if the associated vPort is bridged and act
accordingly. The bridge's notification will be ignored in this case.
Note that bridging a VLAN interface with an ordinary port netdev is
currently not supported, but not forbidden. This will be addressed in a
follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN interface is configured on top of a physical port we should
associate the VLAN device with the matching vPort. Likewise, when it's
removed, we should revert back to the underlying port netdev.
While not a must, this is consistent with port netdevs and also provides
a more accurate error printing via netdev_err() and friends.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously used only one flood table for packets classified to vFIDs.
However, since we are going to add support for bridges between VLAN
interfaces (mapped to vFIDs) we need to add one more flood table.
That way we can separate the flooding domain of unknown unicast traffic
from all the rest and support flood control (as we do with the 802.1Q
bridge).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we used a 1:1 mapping - based on VID - to map a VLAN
interface to a vFID. However, a different scheme is needed in order to
support bridges between VLAN interfaces, as all the member interfaces -
which can have different VIDs - need to share the same vFID.
Solve that by splitting the vFID range in two:
1. Non-bridged VLAN interfaces
2. Bridged VLAN interfaces
When a VLAN interface is created, assign it the next available vFID in
the first range, unless one already exists for that VID or number of
vFIDs in the range was exceeded. When interface is removed, free the
vFID, unless other interfaces are mapped to it.
To accomplish the above:
1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which
has a global context and holds a reference count.
2. Create a vPort (dummy in case of bridge SELF invocation) on top of
of the physical port and hold a reference to the associated vFID.
vfid vfid
+-------------+ +-------------+
| vfid | | vfid |
| vid +---> ... | vid |
| nr_vports | | nr_vports |
+------+------+ +------+------+
|
+-----------------------+-------+
| |
vport vport
+-------------+ +-------------+
| ... | | ... |
| *vfid +---> ... | *vfid +---> ...
| ... | | ... |
+------+------+ +------+------+
| |
port port
+-------------+ +-------------+
| ... | | ... |
| vports_list | | vports_list |
| ... | | ... |
+-------------+ +-------------+
swXpY swXpZ
Next patches in the series will add the missing infrastructure for the
second range and transfer vPorts between the two ranges according to the
received notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for bridges between VLAN interfaces, we'll introduce
a new entity called a vPort, which is a represntation of the VLAN
interface in the hardware.
The main difference between a vPort and a physical port is that several
FIDs can be bound to the latter, whereas only one (called a vFID) can be
bound to the first.
Therefore, it makes sense to use the same struct to represent the two,
but to only allocate the 'active_vlans' bitmap in case of a physical
port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "err = " assignment is missing here.
Fixes: 0d65fc1304 ('mlxsw: spectrum: Implement LAG port join/leave')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling/disabling TX on a LAG port means enabling/disabling distribution
in our HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement basic procedures for joining/leaving port to/from LAG. That
includes HW setup of collector, core LAG mapping setup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add just a stub for now. This allows to pass check in dev_ifsioc,
SIOCADDMULTI and SIOCDELMULTI cases. Teamd is using these to add LACP
slow MAC.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to flash the port's LED in order to identify it. This is
achieved by setting the Management LED Control Register (MLCR).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove a bridged port from the flooding domain of unknown unicast
packets according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a flag anyway, so move it to existing u8 flag and don't waste mem.
Fix the flags to be in single u8 on the way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new generation Mellanox Spectrum ASIC, 10/25/40/50 and
100Gb/s Ethernet Switch.
The initial driver implements bridge forwarding offload including
bridge internal VLAN support, FDB static entries, FDB learning and
HW ageing including their setup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
