Cited commit mistakenly removed the trap group for externally routed
packets (e.g., via the management interface) and grouped locally routed
and externally routed packet traps under the same group, thereby
subjecting them to the same policer.
This can result in problems, for example, when FRR is restarted and
suddenly all transient traffic is trapped to the CPU because of a
default route through the management interface. Locally routed packets
required to re-establish a BGP connection will never reach the CPU and
the routing tables will not be re-populated.
Fix this by using a different trap group for externally routed packets.
Fixes: 8110668ecd ("mlxsw: spectrum_trap: Register layer 3 control traps")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow QSFP-DD transceivers temperature thresholds reading for hardware
monitoring and thermal control.
For this type, the thresholds are located in page 02h according to the
"Module and Lane Thresholds" description from Common Management
Interface Specification.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Quad Small Form Factor Pluggable Double Density (QSFP-DD) hardware
specification defines a form factor that supports up to 400 Gbps in
aggregate over an 8x50-Gbps electrical interface. The QSFP-DD supports
both optical and copper interfaces.
Implementation is based on Common Management Interface Specification;
Rev 4.0 May 8, 2019. Table 8-2 "Identifier and Status Summary (Lower
Page)" from this spec defines "Id and Status" fields located at offsets
00h - 02h. Bit 2 at offset 02h ("Flat_mem") specifies QSFP EEPROM memory
mode, which could be "upper memory flat" or "paged". Flat memory mode is
coded "1", and indicates that only page 00h is implemented in EEPROM.
Paged memory is coded "0" and indicates that pages 00h, 01h, 02h, 10h
and 11h are implemented. Pages 10h and 11h are currently not supported
by the driver.
"Flat" memory mode is used for the passive copper transceivers. For this
type only page 00h (256 bytes) is available. "Paged" memory is used for
the optical transceivers. For this type pages 00h (256 bytes), 01h (128
bytes) and 02h (128 bytes) are available. Upper page 01h contains static
advertising field, while upper page 02h contains the module-defined
thresholds and lane-specific monitors.
Extend enumerator 'mlxsw_reg_mcia_eeprom_module_info_id' with additional
field 'MLXSW_REG_MCIA_EEPROM_MODULE_INFO_TYPE_ID'. This field is used to
indicate for QSFP-DD transceiver type which memory mode is to be used.
Expose 256 bytes buffer for QSFP-DD passive copper transceiver and
512 bytes buffer for optical.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add policer bandwidth limits for both rate and burst size so that they
could be enforced by a later patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The trap identifier was increased to 10 bits in new versions of the
Programmer's Reference Manual (PRM).
Increase it accordingly in the Host PacKet Trap (HPKT) register and in
the Completion Queue Element (CQE).
This is significant for subsequent patches that will introduce trap
identifiers which utilize the extended range.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow setting mirroring_pid_base using MOGCR register.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow setting session_id and pid as part of port analyzer
configurations.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used for global port analyzer configurations.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used to configure the mirror enable for different
mirror reasons.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PDDR register enables to read the Phy debug database.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to layer 2 control traps, register layer 3 control
traps with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bidirectional Forwarding Detection (BFD) provides "low-overhead,
short-duration detection of failures in the path between adjacent
forwarding engines" (RFC 5880).
This is accomplished by exchanging BFD packets between the two
forwarding engines. Up until now these packets were trapped via the
general local delivery (i.e., IP2ME) trap which also traps a lot of
other packets that are not as time-sensitive as BFD packets.
Expose dedicated traps for BFD packets so that user space could
configure a dedicated policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch the split is no longer necessary and all the
trap groups can be moved under the same enum.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of Spectrum trap groups is not infinite, but two identifiers
are occupied by SwitchX-2 specific trap groups. Free these identifiers
by moving them out of the main enum.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet enters the device it is classified to a filtering
identifier (FID) based on the ingress port and VLAN. The FID miss trap
is used to trap packets for which a FID could not be found.
In mlxsw this trap should only be triggered when a port is enslaved to
an OVS bridge and a matching ACL rule could not be found, so as to
trigger learning.
These packets are therefore completely unrelated to packets hitting
local routes and should be in a different group. Move them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 Neighbour Discovery (ND) group will be used for various IPv6
packets, not all of which fall under the definition of ND, so rename it
to "IPV6" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that are trapped via tc's trap action are currently subject to
the same policer as packets hitting local routes. The latter are
critical to the correct functioning of the control plane, while the
former are mainly used for traffic inspection.
Split the ACL trap to a separate group with its own policer. Use a
higher priority for these traps than for traps using mirror action
(e.g., ARP, IGMP). Otherwise, packets matching both traps will not be
forwarded in hardware (because of trap action) and also not forwarded in
software because they will be marked with 'offload_fwd_mark'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rate with which packets are sampled is determined by user space, so
there is no need to associate such packets with a policer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARP trap group will be used for IPv6 ND traps in the next patch, so
rename it to "NEIGH_DISCOVERY" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both packet types are needed for the same reason (multicast snooping),
so associate them with the same trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGMP trap group will be used for MLD traps in the next patch, so
rename it to "MC_SNOOPING" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Infrastructure Entry Delete Register (IEDR) is used to delete
entries stored in the KVD linear database. Currently, it is only
possible to delete entries of size up to 2048. Future firmware versions
will support deletion of entries of size up to 4096.
Increase the size of the field so that the driver will be able to
perform such deletions in the future, when required.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some packet traps are currently exposed to user space as being member of
"l3_drops" trap group, but internally they are member of a different
group.
Switch these traps to use the correct group so that they are all subject
to the same policer, as exposed to user space.
Set the trap priority of packets trapped due to loopback error during
routing to the lowest priority. Such packets are not routed again by the
kernel and therefore should not mask other traps (e.g., host miss) that
should be routed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QoS Policer Configuration Register (QPCR) is used to configure
hardware policers. Extend this register with following fields and
defines which will be used by subsequent patches:
1. Violate counter: reads number of packets dropped by the policer
2. Clear counter: to ensure we start counting from 0
3. Rate and burst size limits
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit set a value of 2^31-1 in order to "disable" the shaper
on a given a port. However, the length of the maximum shaper rate field
was not updated from 28 bits to 31 bits, which means ports are still
limited to ~268Gbps despite supporting speeds of 400Gbps.
Fix this by increasing the field's length.
Fixes: 92afbfedb7 ("mlxsw: reg: Increase MLXSW_REG_QEEC_MAS_DIS")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are couple new values that PMTM register can return
in module_type field. Add them and map them to module width in
mlxsw_core_module_max_width(). Fix the existing names on the way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, only one SFN query is done from repetitive work at a time,
processing 64 entries. Another work iteration is scheduled in 100ms,
that means that the max rate of learned FDB entries is limited to 6400/s.
That is slow. Fix this by doing 2 optimizations:
1) Run 10 SFN queries at a time.
2) In case the SFN is not drained, schedule work with 0 delay to allow
to continue processing rest of the records.
On a testing setup with 500K entries the time to process decreased
from 870secs to 10secs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trap group used to report ACL drops. Setup the trap IDs for
ingress/egress flow action drop. Register the two packet traps
associated with ACL trap group with devlink during driver
initialization. As these are "source traps", set the disabled
trap group to be the dummy, discarding as many packets in HW
as possible.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For "source traps" it is not possible to change HPKT action to discard.
But there is still need to disallow packets arriving to CPU as much as
possible. Handle this by introduction of a "dummy group". It has a
"thin" policer, which passes as less packets to CPU as possible. The
rest is going to be discarded there. The "dummy group" is to be used
later on by ACL trap (which is a "source trap").
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the port speeds grow, the current value of "unlimited shaper",
200000000Kbps, might become lower than the actually supported speeds. Bump
it to the maximum value that fits in the corresponding QEEC field, which is
about 2.1Tbps.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QEEC register configures scheduling elements. One of the bits of
configuration is the burst size to use for the shaper installed on the
element. Add the necessary fields to support this configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trap IDs and trap group used to report tunnel drops. Register
tunnel packet traps and associated tunnel trap group with devlink
during driver initialization.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures the actions that are done during IPinIP
decapsulation based on the ECN bits.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register performs mapping from overlay ECN to underlay ECN during
IPinIP encapsulation.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add QPDP. This register controls the port default Switch Priority and
Color. The default Switch Priority and Color are used for frames where the
trust state uses default values. Currently there are two cases where this
applies: a port is in trust-PCP state, but a packet arrives untagged; and a
port is in trust-DSCP state, but a non-IP packet arrives.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes: 11566d34f8 ("mlxsw: spectrum: Add VRRP traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These enums want to be named MLXSW_REG_QEEC_HIERARCHY_, but due to a typo
lack the second H. That is confusing and complicates searching.
But actually the enumerators should be named _HR_, because that is how
their enum type is called. So rename them as appropriate.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trap IDs and trap group used to report layer 3 drops. Register
layer 3 packet traps and associated layer 3 trap group with devlink
during driver initialization.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PMTM allows query or configuration of module types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx/rx lane fields got extended to 4 bits, update the reg field
description accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In new firmware versions this register is extended with a sampling rate
for Spectrum-2 and future ASICs.
Increase the size of the register to ensure the field is initialized to
0 which means every packet is mirrored.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a macro for getting QSFP module EEPROM page number from the
optional upper page number row offset, specified in request.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Extend speed support with 400Gbps
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend MGPIR - Management General Peripheral Information Register
with new field "num_of_modules" exposing the number of modules
supported by specific system.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 275e928f19 ("mlxsw: spectrum: Prevent force of 56G") prevented
the driver from setting a speed of 56G when auto-negotiation is off.
This is the only speed supported by mlxsw that cannot be set when
auto-negotiation is off, which makes it difficult to write generic
tests.
Further, the speed is not supported by newer ASICs such as Spectrum-2
and to the best of our knowledge it is not used by current users.
Therefore, remove 56G support from mlxsw.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discard trap groups are defined in a different enum so that they could
all share the same policer ID: MLXSW_REG_HTGT_TRAP_GROUP_MAX + 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches will add discard traps support in mlxsw. The driver
cannot configure such traps with a normal trap action, but needs to use
exception trap action, which also increments an error counter.
On the other hand, when these traps are initialized or set to drop
action, they should use the default drop action set by the firmware.
This guarantees that when the feature is disabled we get the exact same
behavior as before the feature was introduced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPSC allows advanced configuration of the PTP shapers.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP Shaper field is used for enabling and disabling of port-rate based
shaper which is slightly lower than port rate.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configured, the Spectrum hardware can recognize PTP packets and
trap them to the CPU using dedicated traps, PTP0 and PTP1.
One reason to get PTP packets under dedicated traps is to have a
separate policer suitable for the amount of PTP traffic expected when
switch is operated as a boundary clock. For this, add two new trap
groups, MLXSW_REG_HTGT_TRAP_GROUP_SP_PTP0 and _PTP1, and associate the
two PTP traps with these two groups.
In the driver, specifically for Spectrum-1, event PTP packets will need
to be paired up with their timestamps. Those arrive through a different
set of traps, added later in the patch set. To support this future use,
introduce a new PTP op, ptp_receive.
It is possible to configure which PTP messages should be trapped under
which PTP trap. On Spectrum systems, we will use PTP0 for event
packets (which need timestamping), and PTP1 for control packets (which
do not). Thus configure PTP0 trap with a custom callback that defers to
the ptp_receive op.
Additionally, L2 PTP packets are actually trapped through the LLDP trap,
not through any of the PTP traps. So treat the LLDP trap the same way as
the PTP0 trap. Unlike PTP traps, which are currently still disabled,
LLDP trap is active. Correspondingly, have all the implementations of
the ptp_receive op return true, which the handler treats as a signal to
forward the packet immediately.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register serves to configure global parameters of certain
monitoring operations. The following patches will use it to configure
that when PTP timestamps are delivered through the PTP FIFO traps, the
FIFO in question is cleared as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTPPTR is used for reading the per port PTP timestamp FIFO.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used for configuring under which trap to deliver PTP
packets depending on type of the packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register serves for configuration of which PTP messages should be
timestamped. This is a global configuration, despite the register name.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend macros MLXSW_REG_MTMP_TEMP_TO_MC() to allow support of negative
temperature readout, since chip and others thermal components are
capable of operating within the negative temperature.
With no such support negative temperature will be consider as very high
temperature and it will cause wrong readout and thermal shutdown.
For negative values 2`s complement is used.
Tested in chamber.
Example of chip ambient temperature readout with chamber temperature:
-10 Celsius:
temp1: -6.0C (highest = -5.0C)
-5 Celsius:
temp1: -1.0C (highest = -1.0C)
v2 (Andrew Lunn):
* Replace '%u' with '%d' in mlxsw_hwmon_module_temp_show()
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTPPS register provides the device PPS capabilities, configure the PPS
in and out modules and holds the PPS in time stamp.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTUTC register configures the HW UTC counter.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PVID is removed from a bridge port, the Linux bridge drops both
untagged and prio-tagged packets. Align mlxsw with this behavior.
Fixes: 148f472da5 ("mlxsw: reg: Add the Switch Port Acceptable Frame Types register")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend sensor index size for Management Temperature Bulk Register
(MTBR) and Management Temperature Register (MTMP) upto 12 bits in
order to align registers description with new version of PRM document.
Add define for base sensor index for SFP modules temperature reading
for MTMP register.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MGPIR - Management General Peripheral Information Register, which
allows software to query the hardware and firmware general information
of peripheral entities as Gearboxes etc.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the size of sensor_index field of MTMP (Management Temperature
Register), from 8 to 12 bits due to hardware change.
Add define for sensor index for Gear Box (inter-connects) temperature
reading.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPLR register allows configuration of the port's loopback mode.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MGIR register. MGIR, Management General Information Register, allows
software to query the hardware and firmware general information.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTYS register introduces a new layout for port type-speed fields. These
fields extend the existing ones in order to handle more types and speeds.
For example, the new 200Gbps speed.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename p_eth_proto_adm to p_eth_proto_admin in mlxsw_reg_ptys_eth_unpack
function.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of deriving the port connector type from port admin state, query it
from firmware.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove eth_proto_lp_advertise field in PTYS register since it is not
supported by the firmware.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FORE (Fan Out of Range Event Register), which is used for fan fault
reading.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MTBR (Management Temperature Bulk Register), which is used for port
temperature reading in a bulk mode.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move QSFP EEPROM definitions to common location from the spectrum driver
in order to make them available for other mlxsw modules. They are common
for all kind of chips and have relation to SFF specifications 8024,
8436, 8472, 8636, rather than to chip type.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Spectrum-2 this allows parallel lookups in multiple regions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2 we need to specify the underlay egress router interface
when performing IP-in-IP and NVE packet decapsulation in the underlay
router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fields relevant for Spectrum-2 Loopback IPinIP router interface
creation. Add additional Loopback RIF protocol value - Generic, used for
creation of an explicit underlay RIF, and also add a field named
underlay_rif used for specifying the underlay RIF of a tunnel.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mlxsw driver handles all aspects of updating
the Bloom filter mechanism, set bf_bypass value to false
and allow HW to use Bloom filter.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter is a bit vector which allows the HW a fast lookup on a
small size bit vector, that may reduce the number of lookups on the
A-TCAM memory. PEABFE register allows setting values to the bits of
the bit vector mentioned above.
Add the register to be later used in A-TCAM optimizations.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, multicast routing is implemented explicitly using policy
engine (ACL) block. PEMRBT register is used to bind a dedicated ACL group
to a specific IP protocol.
Add the register to be later used in multicast router implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ASIC detects that a unicast packet is routed through the same
router interface (RIF) from which it ingressed (iRIF == eRIF), it raises
a trap called loopback error (LBERROR).
Thus far, this trap was configured to send a sole copy of the packet to
the CPU so that ICMP redirect packets could be potentially generated by
the kernel.
This is problematic as the CPU cannot forward packets at 3.2Tb/s and
there are scenarios (e.g., "one-armed router") where iRIF == eRIF is not
an exception.
Solve this by changing the trap to send a copy of the packet to the CPU.
To prevent the kernel from forwarding the packet again, it is marked
with 'offload_l3_fwd_mark'.
The trap is configured in a trap group of its own with a dedicated
policer in order not to prevent packets trapped by other traps from
reaching the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used to process learned FDB records from an NVE tunnel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose packets discard counters via ethtool to help with debugging.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow ERP sharing for multiple mask. Do it by properly implementing
delta_create() objagg object. Use the computed delta info for inserting
rules in A-TCAM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add QEEC.mise (minimum shaper enable) and QEEC.min_shaper_rate to enable
configuration of minimum shaper.
Increase the QEEC length to 0x20 as well: that's the length that the
register has had for a long time now, but with the configurations that
mlxsw typically exercises, the firmware tolerated 0x1C-sized packets.
With mise=true however, FW rejects packets unless they have the full
required length.
Fixes: b9b7cee405 ("mlxsw: reg: Add QoS ETS Element Configuration register")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used for setting up the parsing for hash, policy-engine
and routing.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used to program the device with FDB records pointing to a NVE
tunnel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TNQDR register configures the default QoS settings for NVE
encapsulation.
It will be used to set the default DSCP of each port to 0, so that when
DSCP is set to inherit and the overlay packet does not have an IP header
the outer DSCP will be set to 0, in accordance with the software data
path.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register configures how QoS is set in Encapsulation into the
underlay network.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures the actions that are done during NVE
decapsulation based on the ECN bits.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register performs mapping from overlay ECN to underlay ECN during
NVE encapsulation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register builds the linked list of underlay destination IPs used
for BUM traffic on the overlay.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register enables / disables learning on different types of tunnel
ports (e.g., NVE, VPLS).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures global NVE configuration such as source IP of
the NVE tunnel and UDP source port calculation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the seed of the LAG hash function is always set to 0, which
means it is identical across all switches. Instead, use a random number.
This is especially important now that VxLAN is supported, as the LAG
hash function is used to calculate the UDP source port of the
encapsulated packet.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device has the ability to flush all the FDB records that perform NVE
encapsulation or only a subset of these with a specific filtering
identifier (FID).
Expose these types so that they could be used by subsequent patches
where we need to flush the FDB records when an NVE device is unlinked
from a bridge (FID).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBCM register configures the shared buffer configuration according
to port and TC. So far all pools have had a dynamic size, where the
infinite size is easy to express by using max_buff of 0xff. However the
MC pool should be configured with static size, and the infinite size
thus needs to be set using the field SBCM.infi_max.
Therefore add the field infi_max to the SBCM register and to
mlxsw_reg_sbcm_pack(). Extend mlxsw_sp_sb_cm_write() to handle infinite
sizes as well. Report infinite pool limits as if the limit actually were
the total shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC pool should have an infinite size (i.e. no quota).
To that end, add infi_size to the SBPR register and extend
mlxsw_reg_sbpr_pack(). Also add MLXSW_SP_SB_INFI to denote
buffers that should have an infinite size.
Change mlxsw_sp_sb_pr_write() to take as parameter byte size,
instead of cell size, and add the special handling of infinite
buffers. Report pools with infinite size as if they actually
take the full shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures if the Switch Priority to Traffic Class mapping
is based on Multicast packet indication. If so, then multicast packets
will get a Traffic Class that is plus (cap_max_tclass_data/2) the value
configured by QTCT.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register controls mapping from Priority to DSCP for purposes of
rewrite. Note that rewrite happens as the packet is transmitted provided
that the DSCP rewrite bit is enabled for the packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures the rewrite enable (whether PCP or DSCP value
in packet should be updated according to packet priority) per receive
port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPTS register controls the port policy to calculate the switch
priority and packet color based on incoming packet fields.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPDPM register controls the mapping from DSCP field to Switch
Priority for IP packets.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the pieces are in place we can start using the A-TCAM
instead of only using the C-TCAM. This allows for much higher scale and
better performance (to be improved further by follow-up patch sets).
Perform the integration with the A-TCAM and the eRP core by reverting
the changes introduced by "mlxsw: spectrum_acl: Enable C-TCAM only mode
in eRP core" and add calls from the C-TCAM code into the eRP core.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register is used to add and delete eRPs from the eRP table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register is used to configure rules in the A-TCAM.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before introducing A-TCAM support we need to make sure all the necessary
fields are configurable and not hard coded to values that worked for the
C-TCAM only use case.
This includes - for example - the ability to configure the eRP table
used by the TCAM region.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PGCR register configures general Policy-Engine settings.
Specifically, we are going to use it in order to set the default action
base pointer, which determines where the default action (when there is
no hit) is located for each region.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PERERP register configures the region eRPs. It can be used, for
example, to enable lookup in the C-TCAM in addition to the A-TCAM.
To be able to perform a lookup in the C-TCAM we need to "use" the eRP
table. This is done by marking the pointer as valid, but zeroing the eRP
table vector.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PERCR register configures the region parameters such as whether to
consult the bloom filter before performing a lookup using a specific
eRP.
For C-TCAM only usage we don't need to accurately set the master mask.
Instead, we can set all of its bits to make sure all the extracted keys
are actually used.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PERAR register is used to associate a hw region for region_id's.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, the PEFA register is extend to report if the action set
was hit during processing of packets. Introduce this extension and
adjust the code around this accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEDR register is used for deleting entries from the entry tables.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose counters ASIC has in the group of RFC 2819 counters that count
number of packets within specific size range.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hosts using a VRRP router send their packets with a destination MAC of
the VRRP router which is of the following form [1]:
IPv4 - 00-00-5E-00-01-{VRID}
IPv6 - 00-00-5E-00-02-{VRID}
Where VRID is the ID of the virtual router. Such packets are directed to
the router block in the ASIC by an FDB entry that was added in the
previous patch.
However, in certain cases it is possible to skip this FDB lookup and
send such packets directly to the router. This is accomplished by adding
these special MAC addresses to the RIF cache. If the cache is hit, the
packet will skip the L2 lookup and ingress the router with the RIF
specified in the cache entry.
1. https://tools.ietf.org/html/rfc5798#section-7.3
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is going to be needed for Spectrum-2 C-TCAM implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce Flex2 key type for PTAR register which is used in Spectrum-2.
Also, extend mlxsw_reg_ptar_pack() to set the value according to the
caller.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MLXSW_REG_MPAT_SPAN_TYPE_REMOTE_ETH to support VLAN-encapsulated
port mirroring.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields for the rmft register necessary for setting the IPv6
multicast FIB table. Add a matching wrapper function for filling
the register in the IPv6 scenario.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to what was done in commit 4af5964e58 ("mlxsw: reg:
Configure RIF to forward IPv4 multicast packets by default") we now set
two additional bits to allow IPv6 multicast forwarding.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 'auto-neg off' the device have sent AN (auto-negotiation) frames
with the forced speed. Thus, fix it using an_disable_admin field in
Port type and speed (PTYS) register. This field indicates if speed
negotiation frames would be send by the port or not.
Add the field and enable/disable it for 'auto-neg on/off', make the
port to start/stop sending AN (auto-negotiation) frames. Note that for
SwitchX2 the behavior doesn't change (i.e support only AN enabled with
forced speed).
Signed-off-by: Tal Bar <talb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support encapsulated SPAN, extend mlxsw_reg_mpat_pack() with a field
to set the SPAN type.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPAT Register is used to query and configure the Switch Port Analyzer
Table. To configure Port Analyzer to encapsulate mirrored packets,
additional fields need to be specified for the MPAT register.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rdpm definition - router DSCP to priority mapping register.
This register will be utilized later to align the default mapping between
packet DSCP and switch-priority to the kernel's mapping between
packet priority and skb priority.
This is the first non-bit indexed register where the entries are arranged
in descending order, i.e., entry at offset 0 matches configuration for
dscp[63]. As a result, the item's step is converted into a signed variable
to support descending arrays [where step would be negative].
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the counter group definitions for 2 new counter groups
which are necessary for gaining ECN & wred counters.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 2 new registers:
- Congestion WRED ECN TClass Profile Register [CWTP]
- Congestion WRED ECN TClass and Pool Mapping Register [CWTPM]
These registers would later be needed to offload RED-related
functionality to the HW.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RECRv2 register is used for setting up the router's ECMP hash
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASIC has the ability to generate events whenever a sensor indicates
the temperature goes above or below its high or low thresholds,
respectively.
In new firmware versions the firmware enforces a minimum of 5
degrees Celsius difference between both thresholds. Make the driver
conform to this requirement.
Note that this is required even when the events are disabled, as in
certain systems interrupts are generated via GPIO based on these
thresholds.
Fixes: 85926f8770 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace recurring magic number in PPCNT register with a define.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIGCR register is used for setting up the IPinIP Tunnel
configuration.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to add the ability for setting counters on nexthops the RATR
register should be extended.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three new traps needed for multicast routing:
- PIM: Trap for PIM protocol control packets.
- RPF: Trap for packets that fail the RPF check on a specific hardware
route entry.
- MULTICAST: Generic trap for multicast. It is used for routes that trap
the packets to the CPU.
The RPF and MULTICAST traps have rate limiters as these traps may have
line-rate of packets trapped. The PIM trap has a rate limiter similarly to
other L3 control protocols. The rate limiters are implemented by adding
three new trap groups for the newly introduced traps.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn on two bits on the Spectrum RIF configuration:
- IPv4 multicast: when a multicast packet arrives on a RIF, send it to go
through multicast routes lookup.
- IPv4 multicast forwarding enable: when multicast packet arrives on a
RIF, allow it to be forwarded by multicast routes. If this bit is not
set, multicast packets will go through multicast routing lookup but will
be dropped at the egress of the ports.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RRCR register is used for copying and moving TCAM multicast routes
from different offsets. It will be used to allow routes relocation for
parman ops as part of the multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RMFT-V2 register is used to configure and query the multicast table and
will be used by the multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RIGR-V2 register is used to add, remove and query egress interface list
of a multicast forwarding entry and it will be used by the multicast
router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used for allocation of regions in the TCAM table and it
will be used by the multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MLXSW_REG_PXXX_FLEX_ACTION_SET_LEN is relevant for the multicast router
registers too, so rename it to have a general name which is not bound to a
specific register.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support IPIP, the driver needs to be able to construct an IPIP
adjacency. Change mlxsw_reg_ratr_pack to take an adjacency type as an
argument. Adjust the one existing caller.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike other interface types, loopback RIFs do not have MAC address. So
drop the corresponding argument from mlxsw_reg_ritr_pack() and move it
to a new function. Call that from callers of mlxsw_reg_ritr_pack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTDP register is used for configuring the tunnel decap properties of
NVE and IPinIP.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To implement IP-in-IP decapsulation, Spectrum uses LPM entries of type
IP2ME with tunnel validity bit and tunnel pointer set. The necessary
register fields are already available, so add a function to pack the
RALUE as appropriate.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enum is used with reg_ratr_trap_id, so move it next to the register
definition.
While at it, drop the enumerator initializers.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, adjacencies have always been of type Ethernet (with value of 0),
and thus there was no need to explicitly support RATR type. However to
support IP-in-IP adjacencies, this type and a suite of IP-in-IP-specific
attributes need to be added.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the register so that loopback RIFs can be created and loopback
properties specified.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting counters on neighbors based on dpipe's host table
counter status. This patch also adds the ability for getting the counter
value, which will be used by the dpipe host table implementation in the
next patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before introducing support for neighbor
counters. The flow counter's type enum is used by many registers, yet,
until now it was used only by mgpc and thus it was private. This patch
updates the namespace for more generic usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames IP2ME-specific registers reg_ralue_v and
reg_ralue_tunnel_ptr to reg_ralue_ip2me_*.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments really belong to the individual enumerators. The comment
at the register should instead reference the enum.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the register so that IPv6 LPM entries could be programmed to the
device's table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the register so that the active IPv6 neighbours could be dumped
from the device's neighbour table.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the register, so the IPv6 neighbours could be programmed to the
device's neighbour table.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we can start using IPv6, we need to trap certain control packets
to the CPU. Among others, these include Neighbour Discovery, DHCP and
neighbour misses.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable IPv6 and IPv6 forwarding on router interfaces (RIFs), so that
they will be able to receive and forward IPv6 traffic.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we add IPv6 constructs like traps and router interfaces, we first
need to enable IPv6 routing in the device.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 MLDv1/2 packet trapping.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCIA register is used to access the SFP+ and QSFP connector's
EPROM. It will be used to query the cable info.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCDA register allows reading and writing a firmware component.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCC register allows controlling and querying the firmware flash state
machine (FSM).
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCQI register queries information about firmware components. It will
be needed by the mlxfw module to query various options about the
components, such as their max size, alignment and max write size.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RICNT register retrieves per port performance counter. It will be
used to query the router interfaces statistics.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update RITR for counter support. This allows adding counters for
ASIC's router ports.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmgenet.c
net/core/sock.c
Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.
Fixes: a4feea74cd ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.
Fixes: b2e345f9a4 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MGPC register retrieves generic flow counter value. It will be
used to query ACL counters.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we implicitly associated all the router interfaces (RIFs)
with the first virtual router (VR). This must be changed in order to
enable VRF offload. Otherwise, a packet received via a VRF slave would
do a FIB lookup in the same table used by other VRFs.
Instead, bind the RIF to a VR according to the table where FIB lookup
should be performed for packets received via the RIF.
Currently, we only care about the MAIN and LOCAL tables (which we squash
together).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HTGT register length is limited to 32 bytes and not 256 bytes.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PEFA register is used for accessing an extended flexible action entry
in the central KVD Linear Database.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPBS register retrieves and sets Policy Based Switching Table entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PRCR register is used for accessing rules within a TCAM region.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPBT is used for configuration of the Port Binding Table.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTCE-V2 register is used for accessing rules within a TCAM region.
It is a new version of PTCE in order to support wider key, mask and
action within a TCAM region.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTAR register is used for allocation of regions in the TCAM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PAGT register is used for configuration of the ACL Group Table.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PACL register is used for configuration of the ACL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPSC register allows to configure ingress packet sampling on specific
port of the mlxsw device. The sampled packets are then trapped via
PKT_SAMPLE trap.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPCR register is used to create and control policers.
A policer can discard or change the color of packets that are
trapped by a specific trap.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups can be used to control traps priority, both in terms of
which trap "wins" if a packet matches two traps (priority) and in terms
of packets from which trap group will be scheduled to the cpu first (tc).
They can also be used to set rate limiters (policers) on them (will be
added in the next patches).
Currently, we support two trap groups. In Spectrum we want a better
resolution, so every protocol / flow will have a different trap group,
so we can control its parameters separately. Once the policers will be
implemented, it will also allow us limit the rate of each protocol by
itself.
This patch change the trap group list to include:
* the emad trap group, which is shared for all the devices.
* Switchx2's trap groups, which are a copy of the current trap groups.
* Spectrum's new trap groups, in order to match the above guidelines.
(Switchib is using only the emad trap group, so it require no changes).
This patch also includes new configuration for Spectrum's trap groups,
with primary priority order within them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups have many options which we currently set to default values.
In the next patches we will use many of them with non-default values.
Some of these options have no default value, so this patch sets them as
params for the trap group set function. Others almost always use the same
values, so the set function will use this default values. In the rare cases
when they will need to be with other values, these values can be set
directly (using the macros for fields in registers).
Parameters without default value:
TC - the traffic class for packets that hit this trap group.
(old default is the max tc)
priority - if one packet hits multiple trap groups, the group with the
higher priority will "catch" it. (old default is 0)
policer - limit rate policer (old default is disabled)
Default parameters:
swid - switch id, relevant for the emad trap only, ignored on Spectrum.
(new default is 0)
rdq - CPU receive descriptor queue (new default is identical to trap
group id)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change trap setting function so instead of determining the trap group by
trap id, it gets it as a parameter (so later we can have different trap
groups for Spectrum and Switchx2).
Add "is_ctrl" parameter to the trap setting function. It control whether
the trapped packets wait in a designated control buffer or in their
default one. This parameter is ignored by Switchx2 and Switchib.
Add these parameters to the traps array in Spectrum, Switchx2 and
Switchib.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFSL register is used to configure the fan speed event / interrupt
notification mechanism. Fan speed threshold are defined for both
under-speed and over-speed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to change a port type to Infiniband port we should change his
mapping from local-port to Infiniband. Adding the PLIB (Port Local to
InfiniBand) allows this mapping.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support Infiniband fabric, we need to introduce IB speeds and
capabilities to PTYS emads.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add Infiniband support to PTYS. In order to maintain proper
conventions, we will change pack and unpack prefix to eth.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the MLXSW_REG_DEFINE macro to store register name in string form.
Use this string later on instead of hard coded string values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save some code and also prepare to easily carry name in string form.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the RX hash function from XOR to CRC in order to have better
distribution of the traffic.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the deprecated {get,set}_settings callbacks and instead add
{get,set}_link_ksettings along with support for newly available speeds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If autonegotiation was performed successfully, then we should report the
link partner's advertised speeds instead of the operational speed of the
port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now a learning session ended whenever the number of queried
records was zero. This turned out to be problematic in situations where
a large number of MACs (48K) had to be processed by the switch driver,
as RTNL mutex is held during the learning session.
Instead, limit the number of FDB records that can be processed in a
session to 64. This means that every time the device is queried for
learning notifications (currently, every 100ms), up to 64 records will
be processed by the switch driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
