During initialization, the AF driver resets all blocks. The RPM (MAC)
block and NIX block operate on a credit-based model. When the NIX block
resets during active traffic flow, it doesn't release credits to the RPM
block. This causes the RPM FIFO to overflow, leading to receive traffic
struck.
To address this issue, the patch introduces the following changes:
1. Stop receiving traffic at the MAC level during AF driver
initialization.
2. Perform an X2P reset (prevents RXFIFO of all LMACS from pushing data)
3. Reset the NIX block.
4. Clear the X2P reset and re-enable receiving traffic.
Fixes: 54d557815e ("octeontx2-af: Reset all RVU blocks")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The corrected words register(FCFECX_VL0_CCW_LO)/Uncorrected words
register (FCFECX_VL0_NCCW_LO) of FCFEC counter has different LMAC
offset which needs to be accessed differently.
Fixes: 84ad364211 ("octeontx2-af: Add FEC stats for RPM/RPM_USX block")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The earlier patch sets the 'Stats control register' for RPM
receive/transmit statistics instead of RSFEC statistics,
causing the driver to return stale FEC counters.
Fixes: 84ad364211 ("octeontx2-af: Add FEC stats for RPM/RPM_USX block")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Low network performance is observed even on RPMs with larger
FIFO lengths.
The cn10kb silicon has three RPM blocks with the following
FIFO sizes:
--------------------
| RPM0 | 256KB |
| RPM1 | 256KB |
| RPM2 | 128KB |
--------------------
The current design stores the FIFO length in a common structure for all
RPMs (mac_ops). As a result, the FIFO length of the last RPM is applied
to all RPMs, leading to reduced network performance.
This patch resolved the problem by storing the fifo length in per MAC
structure (cgx).
Fixes: b9d0fedc62 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Due to a bug in the previous patch, there is a mismatch
between the lmac type reported by the driver and the actual
hardware configuration.
Fixes: 3ad3f8f93c ("octeontx2-af: cn10k: MAC internal loopback support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reset CGX/RPM MAC HW statistics at the time of driver probe()
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPM0 and RPM1 on the CN10KB SoC have 8 LMACs each, whereas RPM2
has only 4 LMACs. Similarly, the RPM0 and RPM1 have 256KB FIFO,
whereas RPM2 has 128KB FIFO. This patch fixes an issue with
improper TX credit programming for the RPM2 link.
Fixes: b9d0fedc62 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240108073036.8766-1-naveenm@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current implementation's default Pause Forward setting is causing
unnecessary network traffic. This patch disables Pause Forward to
address this issue.
Fixes: 1121f6b02e ("octeontx2-af: Priority flow control configuration support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppose user has enabled pfc with prio 0,1 on a PF netdev(eth0)
dcb pfc set dev eth0 prio-pfc o:on 1:on
later user enabled pfc priorities 2 and 3 on the VF interface(eth1)
dcb pfc set dev eth1 prio-pfc 2:on 3:on
Instead of enabling pfc on all priorities (0..3), the driver only
enables on priorities 2,3. This patch corrects the issue by using
the proper CSR address.
Fixes: b9d0fedc62 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230824081032.436432-3-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
AF driver configures MAC features like internal loopback and PFC upon
receiving the request from PF and its VF netdev. But these
features are not getting reset in FLR. This patch fixes the issue by
resetting the same.
Fixes: 23999b30ae ("octeontx2-af: Enable or disable CGX internal loopback")
Fixes: 1121f6b02e ("octeontx2-af: Priority flow control configuration support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current design is that, for asynchronous events like link_up and
link_down firmware raises the interrupt to kernel. The previous patch
which added RPM_USX driver has a bug where it uses old csr addresses
for configuring interrupts. Which is resulting in losing interrupts
from source firmware.
This patch fixes the issue by correcting csr addresses.
Fixes: b9d0fedc62 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K silicon MAC block RPM and CN10KB silicon MAC block RPM_USX
both support BASER and RSFEC modes.
Also MAC (CGX) on OcteonTx2 silicon variants and MAC (RPM) on
OcteonTx3 CN10K are different and FEC stats need to be read
differently. CN10KB MAC block (RPM_USX) fec csr offsets are same
as CN10K MAC block (RPM) mac_ops points to same fn(). Upper layer
interface between RVU AF and PF netdev is kept same. Based on
silicon variant appropriate fn() pointer is called to read FEC stats
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
OcteonTx2's next gen platform the CN10KB has RPM_USX MAC which has a
different serdes when compared to RPM MAC. Though the underlying
HW is different, the CSR interface has been designed largely inline
with RPM MAC, with few exceptions though. So we are using the same
CGX driver for RPM_USX MAC as well and will have a different set of APIs
for RPM_USX where ever necessary.
The RPM and RPM_USX blocks support a different number of LMACS.
RPM_USX support 8 LMACS per MAC block whereas legacy RPM supports only 4
LMACS per MAC. with this RPM_USX support double the number of DMAC filters
and fifo size.
This patch adds initial support for CN10KB's RPM_USX MAC i.e registering
the driver and defining MAC operations (mac_ops). Adds the logic to
configure internal loopback and pause frames and assign FIFO length to
LMACS.
Kernel reads lmac features like lmac type, autoneg, etc from shared
firmware data this structure only supports 4 lmacs per MAC, this patch
extends this structure to accommodate 8 lmacs.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for ptp 1-step mode using timecounter. The seconds and
nanoseconds to be updated in PTP header are calculated by adding the
timecounter offset to the free running PTP clock counter time. The PF
driver periodically gets the PTP clock time using AF mbox. The 1-step
support uses HW feature to update correction field rather than
OriginTimestamp field in PTP header.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When number of LMACs active on a CGX/RPM are 3, then
current NIX link credit config based on per lmac fifo
length which inturn is calculated as
'lmac_fifo_len = total_fifo_len / 3', is incorrect. In HW
one of the LMAC gets half of the FIFO and rest gets 1/4th.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha Sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In few error cases MAC(CGX/RPM) block is having 0 lmacs.
AF driver uses MAC block with lmac pair to get firmware
data etc. These commands will fail as there is no LMAC
associated with MAC block.
This patch skips the probe of these MAC blocks such that AF driver
uses correct MAC block and LMAC pair for firmware communication and
define new LMAC_AF_ERROR types for command timeout etc.
This patch also enables channel back pressure for all LMACs.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation is such that driver first resets the
existing PFC config before applying new pfc configuration.
This creates a problem like once PF or VFs requests PFC config
previous pfc config by other PFVfs is getting reset.
This patch fixes the problem by removing unnecessary resetting
of PFC config. Also configure Pause quanta value to smaller as
current value is too high.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K MAC block (RPM) and Octeontx2 MAC block (CGX) both supports
PFC flow control and 802.3X flow control pause frames.
Each MAC block supports max 4 LMACS and AF driver assigns same
(MAC,LMAC) to PF and its VFs. As PF and its share same (MAC,LMAC)
pair we need resource management to address below scenarios
1. Maintain PFC and 8023X pause frames mutually exclusive.
2. Reject disable flow control request if other PF or Vfs
enabled it.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prirority based flow control (802.1Qbb) mechanism is similar to
ethernet pause frames (802.3x) instead pausing all traffic on a link,
PFC allows user to selectively pause traffic according to its class.
Oceteontx2 MAC block (CGX) and CN10K Mac block (RPM) both supports
PFC. As upper layer mbox handler is same for both the MACs, this
patch configures PFC by calling apporopritate callbacks.
Signed-off-by: Sunil Kumar Kori <skori@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation is such that 802.3x pause frames are
enabled by default. As CGX and RPM blocks support PFC
(priority flow control) also, instead of driver enabling one
between them enable them upon request from PF or its VFs.
Also add support to disable pause frames in driver unbind.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal looback is not supported to low rate LPCS interface like
SGMII/QSGMII. Hence don't allow to enable for such interfaces.
Fixes: 3ad3f8f93c ("octeontx2-af: cn10k: MAC internal loopback support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K platforms uses RPM(0..2)_MTI_MAC100(0..3)_COMMAND_CONFIG
register for lmac TX/RX enable whereas CN9xxx platforms use
CGX_CMRX_CONFIG register. This config change was missed when
adding support for CN10K RPM.
Fixes: 91c6945ea1 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on CN10K support hardware timestamping such that 8 bytes addition
header is prepended to incoming packets. This patch does necessary
configuration to enable Hardware time stamping upon receiving request
from PF netdev interfaces.
Timestamp configuration is different on MAC (CGX) Octeontx2 silicon
and MAC (RPM) OcteonTX3 CN10k. Based on silicon variant appropriate
fn() pointer is called. Refactor MAC specific mbox messages to remove
unnecessary gaps in mboxids.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed inconsistent license text across the RVU admin
function driver.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on CN10K silicon support loopback for selftest or debug purposes.
This patch does necessary configuration to loopback packets upon receiving
request from LMAC mapped RVU PF's netdev via mailbox.
Also MAC (CGX) on OcteonTx2 silicon variants and MAC (RPM) on
OcteonTx3 CN10K are different and loopback needs to be configured
differently. Upper layer interface between RVU AF and PF netdev is
kept same. Based on silicon variant appropriate fn() pointer is
called to config the MAC.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPM supports below list of counters as an extension to existing counters
* class based flow control pause frames
* vlan/jabber/fragmented packets
* fcs/alignment/oversized error packets
This patch adds support to display supported RPM counters via debugfs
and define new mbox rpm_stats to read all support counters.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control configuration is different for CGX(Octeontx2)
and RPM(CN10K) functional blocks. This patch adds the necessary
changes for RPM to support 802.3 pause frames configuration on
cn10k platforms.
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OcteonTx2's next gen platform the CN10K has RPM MAC which has a
different serdes when compared to CGX MAC. Though the underlying
HW is different, the CSR interface has been designed largely inline
with CGX MAC, with few exceptions though. So we are using the same
CGX driver for RPM MAC as well and will have a different set of APIs
for RPM where ever necessary.
This patch adds initial support for CN10K's RPM MAC i.e. the driver
registration, communication with firmware etc. For communication with
firmware, RPM provides a different IRQ when compared to CGX.
The CGX and RPM blocks support different features. Currently few
features like ptp, flowcontrol and higig are not supported by RPM. This
patch adds new mailbox message "CGX_FEATURES_GET" to get the list of
features supported by underlying MAC.
RPM has different implementations for RX/TX stats. Unlike CGX,
bar offset of stat registers are different. This patch adds
support to access the same and dump the values in debugfs.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
