We shouldn't be recording the Rx queue on macvlan offloaded frames since
the macvlan is normally brought up as a single queue device, and it will
trigger warnings for RPS if we have recorded queue IDs larger than the
"real_num_rx_queues" value recorded for the device.
Instead we should be recording the macvlan statistics since we are
bypassing the normal macvlan statistics that would have been generated by
the receive path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code throughout ixgbe was assuming that dev->num_tc was populated and
configured with the driver, when in fact this can be configured via mqprio
without any hardware coordination other than restricting us to the real
number of Tx queues we advertise.
Instead of handling things this way we need to keep a local copy of the
number of TCs in use so that we don't accidentally pull in the TC
configuration from mqprio when it is configured in software mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We might as well configure the limit to default to 1 pool always for the
interface. This accounts for the fact that the PF counts as 1 pool if
SR-IOV is enabled, and in general we are always running in 1 pool mode when
RSS or DCB is enabled as well, though we don't need to actually evaluate
any of the VMDq features in those cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The macvlan driver itself will validate the MAC address that is configured
for a given interface. There is no need for us to verify it again.
Instead we should be checking to verify that we actually allocate the filter
and have not run out of resources to configure a MAC rule in our filter
table.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The l2 acceleration private pointer isn't needed in the ring struct. It
isn't really used anywhere other than to test and see if we are supporting
an offloaded macvlan netdev, and it is much easier to test netdev for not
being ixgbe based to verify that.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the check for Tx pending traffic and makes it more
holistic as there being any difference between next_to_use and
next_to_clean is much more informative than if head and tail are equal, as
it is possible for us to either not update tail, or not be notified of
completed work in which case next_to_clean would not be equal to head.
In addition the simplification makes it so that we don't have to read
hardware which allows us to drop a number of variables that were previously
being used in the call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is a fix of the macvlan offload so that we correctly handle
macvlan offloaded devices. Specifically we were configuring our limits based
on the assumption that we were going to max out the RSS indices for every
mode. As a result when we went to 15 or more macvlan interfaces we were
forced into the 2 queue RSS mode on VFs even though they could have still
supported 4.
This change splits the logic up so that we limit either the total number of
macvlan instances if DCB is enabled, or limit the number of RSS queues used
per macvlan (instead of per pool) if SR-IOV is enabled. By doing this we
can make best use of the part.
In addition I have increased the maximum number of supported interfaces to
63 with one queue per offloaded interface as this more closely reflects the
actual values supported by the interface.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The num_rx_pools value is overwritten when we reinitialize the queue
configuration. In reality we shouldn't need to be updating the value since
it is redone every time we call into ixgbe_setup_tc so for now just drop
the spots where we were incrementing or decrementing the value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order for RSS to work on the macvlan pools of the X550 we need to
populate the MRQC, RETA, and RSS key values for each pool. This patch makes
it so that we now take care of that.
In addition I have dropped the macvlan specific configuration of psrtype
since it is redundant with the code that already exists for configuring
this value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the number of VFs are changed we need to reinitialize the part since the
offset for the device and the number of pools will be incorrect. Without
this change we can end up seeing Tx hangs and dropped Rx frames for
incoming traffic.
In addition we should drop the code that is arbitrarily changing the
default pool and queue configuration. Instead we should wait until the port
is reset and reconfigured via ixgbe_sriov_reinit.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When SR-IOV was enabled the macvlan offload was configuring several filters
with the wrong pool value. This would result in the macvlan interfaces not
being able to receive traffic that had to pass over the physical interface.
To fix it wrap the pool argument in the VMDQ_P macro which will add the
necessary offset to get to the actual VMDq pool
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The InterruptThrottleRate has been removed from ixgbe. Then Update
the comment.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Extend FW version reporting by displaying information from the iSCSI
or OEM block in the EEPROM.
This will allow us to more accurately identify the FW.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On module insert advertise highest capable link speed. If module is
capable of 10G, then advertise 10G, else advertise modules capable
link speeds.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enum is no longer needed after
commit: b4ded8327f ("ixgbe: Update adaptive ITR algorithm")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we only enabled the reception of multicast packets when
wake on multicast is set, but we also need this to allow waking with
IPv6 magic packets.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.
If we would support moving target netdev across netns, using
pointer would be better than ifindex.
This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a partial revert of "ixgbe: Don't bother clearing buffer
memory for descriptor rings". Specifically I messed up the exception
handling path a bit and this resulted in us incorrectly adding the count
back in when we didn't need to.
In order to make this simpler I am reverting most of the exception handling
path change and instead just replacing the bit that was handled by the
unmap_and_free call.
Fixes: ffed21bcee ("ixgbe: Don't bother clearing buffer memory for descriptor rings")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All drivers are converted to use block callbacks for TC_SETUP_CLS*.
So it is now safe to remove the calls to ndo_setup_tc from cls_*
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the newly introduced block callback infrastructure and
convert ndo_setup_tc calls for u32 offloads to block callbacks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case where AER recovery fails the device is left in a down state.
Consecutive AER error injection can lead to a double IRQ free.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following change is meant to update the adaptive ITR algorithm to
better support the needs of the network. Specifically with this change what
I have done is make it so that our ITR algorithm will try to prevent either
starving a socket buffer for memory in the case of Tx, or overrunning an Rx
socket buffer on receive.
In addition a side effect of the calculations used is that we should
function better with new features such as XDP which can handle small
packets at high rates without needing to lock us into NAPI polling mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bits other than FWSM.PT can be set in IXGBE_SWFW_MODE_MASK making the
previous check invalid.
Change the check for MNG present to be only based on FWSM.PT bit.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.
- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()
- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver have page recycle scheme based around the RX-ring
queue, where a RX page is shared between two packets. Based on the
refcnt, the driver can determine if the RX-page is currently only used
by a single packet, if so it can then directly refill/recycle the
RX-slot by with the opposite "side" of the page.
While this is a clever trick, it is hard to determine when this
recycling is successful and when it fails. Adding a counter, which is
available via ethtool --statistics as 'alloc_rx_page'. Which counts
the number of times the recycle fails and the real page allocator is
invoked. When interpreting the stats, do remember that every alloc
will serve two packets.
The counter is collected per rx_ring, but is summed and ethtool
exported as 'alloc_rx_page'. It would be relevant to know what
rx_ring that cannot keep up, but that can be exported later if
someone experience a need for this.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit: fed21bcee7a5
("ixgbe: Don't bother clearing buffer memory for descriptor rings)
exposed some issues with the logic in the current implementation of
ixgbe_clean_test_rings() that are being addressed in this patch:
- Split the clearing of the Tx and Rx rings in separate loops. Previously
both Tx and Rx rings were cleared in a rx_desc->wb.upper.length based
loop which could lead to issues if for w/e reason packets were received
outside of the frames transmitted for the loopback test.
- Add check for IXGBE_TXD_STAT_DD to avoid clearing the rings if the
transmits have not comlpeted by the time we enter ixgbe_clean_test_rings()
- Exit early on ixgbe_check_lbtest_frame() failure.
This change fixes a crash during ethtool diagnostic (ethtool -t).
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ignoring errors when attempting to identify the PHY can lead to a crash.
Specifically in the case of FW controlled PHYs where the PHY read/write
operations are set to NULL.
Removed redundant comment.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just like when the last VF is removed, we need to restore normal
operations after the last macvlan offload is removed, else we
get stuck in single queue operations.
To test:
ethtool -l eth1 # note the number of queues in use, ~= cpus
ethtool -K eth1 l2-fwd-offload on
ip link add mv1 link eth1 type macvlan mode bridge
ip link set dev mv1 up
ip link del mv1
ethtool -l eth1 # are we back to the same # of queues, or stuck on 1?
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Declare ixgbe_mac_operations structures as const as they are only stored
in the mac_ops field of ixgbe_info structure. This field is of type
const and therefore ixgbe_mac_operations structure can be made const
too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added clearing of SW resource bits in the SW/FW synchronization
register to ixgbe_init_swfw_sync_X540().
Updated ixgbe_acquire_swfw_sync_X540 SW Manageability host interface
resource bit error case to match the error handling of the other SW
resource bits. Which is to release the SW resource bits if SW times
out while attempting to acquire the resource.
This allows the driver to load in cases where the semaphore bits
could be stuck after a reset or a crash.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing the TX ring parameters with an XDP program attached may
cause the XDP queues to be cleared and the TX rings to be incorrectly
configured.
Fix by doing correct ring accounting in setup call.
Fixes: 33fdc82f08 ("ixgbe: add support for XDP_TX action")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver use the compile check to determine if it can
send TLPs to Root Port with the Relaxed Ordering Attribute set,
this is too inconvenient, now the new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING
has been added to the kernel and we could check the bit4 in the PCIe
Device Control register to determine whether we should use the Relaxed
Ordering Attributes or not, so use this new way in the ixgbe driver.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added
to indicate that Relaxed Ordering Attributes (RO) should not
be used for Transaction Layer Packets (TLP) targeted toward
these affected Root Port, it will clear the bit4 in the PCIe
Device Control register, so the PCIe device drivers could
query PCIe configuration space to determine if it can send
TLPs to Root Port with the Relaxed Ordering Attributes set.
With this new flag we don't need the config ARCH_WANT_RELAX_ORDER
to control the Relaxed Ordering Attributes for the ixgbe drivers
just like the commit 1a8b6d76dc ("net:add one common config...") did,
so revert this commit.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_clear_udp_tunnel_port(), we read the IXGBE_VXLANCTRL register
and then try to mask some bits out of the value, using the logical
instead of bitwise and operator.
Fixes: a21d0822ff ("ixgbe: add support for geneve Rx offload")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement support for transferring XDP meta data into skb for
ixgbe driver; before calling into the program, xdp.data_meta points
to xdp.data, where on program return with pass verdict, we call
into skb_metadata_set().
We implement this for the default ixgbe_build_skb() variant. For the
ixgbe_construct_skb() that is used when legacy-rx buffer mananagement
mode is turned on via ethtool, I found that XDP gets 0 headroom, so
neither xdp_adjust_head() nor xdp_adjust_meta() can be used with this.
Just add a comment with explanation for this operating mode.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.
xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.
The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For XDP_REDIRECT the use of return code -EINVAL is confusing, as it is
used in three different cases. (1) When the index or ifindex lookup
fails, and in the ixgbe driver (2) when link is down and (3) when XDP
have not been enabled.
The return code can be picked up by the tracepoint xdp:xdp_redirect
for diagnosing why XDP_REDIRECT isn't working. Thus, there is a need
different return codes to tell the issues apart.
I'm considering using a specific err-code scheme for XDP_REDIRECT
instead of using these errno codes.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use errno -ENOSPC ("No space left on device") when the XDP xmit
have no space left on the TX ring buffer, instead of -ENOMEM.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offending commit used a newly added helper function.
But the logic is wrong. Without this fix, the affected NICs
can't do HW offload. Error -EOPNOTSUPP will be returned directly.
Fixes: a2e8da9378 ("net/sched: use newly added classid identity helpers")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking handle, which does not have the inner class
information and drivers wrongly assume clsact->egress as ingress, use
the newly introduced classid identification helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let __ixgbe_setup_tc be a splitter for specific setup_tc types and push out
cls_u32 and mqprio specific codes into separate functions. Also change
the return values so they are the same as in the rest of the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rest of the helpers are named tcf_exts_*, so change the name of
the action number helpers to be aligned. While at it, change to inline
functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control autonegotiation is not supported for XFI. Make sure that
ixgbe_device_supports_autoneg_fc() returns false and
hw->fc.disable_fc_autoneg is set to true to avoid running the fc_autoneg
function for that device.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flow control autonegotiation is not supported for fiber on X553. Add
device ID checks in ixgbe_device_supports_autoneg_fc() to return the
appropriate value.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC register NW_MNG_IF_SEL fields have been redefined for
X553. These changes impact the iXFI driver code flow. Since iXFI is
only supported in X552, add MAC checks for iXFI flows.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable LASI interrupts on X552 devices in order to receive notifications of
link configurations of the external PHY and support the configuration of
the internal iXFI link since iXFI does not support auto-negotiation. This
is not required for X553 devices; add a check to avoid enabling LASI
interrupts for X553 devices.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a check to ensure that adding the MAC filter was
successful before setting the MACVLAN. If it was unsuccessful, propagate
the error.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For performance reasons we want to avoid updating the tail pointer in
the driver tx ring as much as possible. To accomplish this we add
batching support to the redirect path in XDP.
This adds another ndo op "xdp_flush" that is used to inform the driver
that it should bump the tail pointer on the TX ring.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a trace event for xdp redirect which may help when debugging
XDP programs that use redirect bpf commands.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are optimizations we can add after the basic feature is
enabled. But, for now keep the patch simple.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_rings and rx_rings are cleaned up on close paths in ixgbe driver
however, xdp_rings are not. Set the xdp_rings to NULL here so that
we can use the pointer to indicate if the XDP rings are initialized.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to ixgbe to report bpf_prog ID during XDP_QUERY_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call pci_set_drvdata immediately after calling register_netdev,
which leaves a window where tasks writing to the sriov_numvfs sysfs
attribute can sneak in and crash the kernel. register_netdev cleans
up after itself so placing pci_set_drvdata immediately before it
should preserve the intent of commit 0fb6a55cc3 ("ixgbe: fix crash
on rmmod after probe fail").
Fixes: 0fb6a55cc3 ("ixgbe: fix crash on rmmod after probe fail")
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
cppcheck warns that the format string is incorrect in the function
ixgbe_get_strings(). Since the value cannot be negative, change the
variable to unsigned which matches the format specifier.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_write_qde() was ignoring the qde parameter which resulted
in PFQDE.HIDE_VLAN not being set for X550.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ixgbe version number.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.
It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.
Add an ixgbe_ptp_tx_hang() function similar to the already existing
ixgbe_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.
Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver uses a state bit lock to avoid handling more than one Tx
timestamp request at once. This is required because hardware is limited
to a single set of registers for Tx timestamps.
The state bit lock is not properly cleaned up during
ixgbe_xmit_frame_ring() if the transmit fails such as due to DMA or TSO
failure. In some hardware this results in blocking timestamps until the
service task times out. In other hardware this results in a permanent
lock of the timestamp bit because we never receive an interrupt
indicating the timestamp occurred, since indeed the packet was never
transmitted.
Fix this by checking for DMA and TSO errors in ixgbe_xmit_frame_ring() and
properly cleaning up after ourselves when these occur.
Reported-by: Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware related to the ixgbe driver is limited to handling a single Tx
timestamp request at a time. Thus, the driver ignores requests for Tx
timestamp while waiting for the current request to finish. It uses
a state bit lock which enforces that only one timestamp request is
honored at a time.
Unfortunately this suffers from a simple race condition. The bit lock is
not cleared until after skb_tstamp_tx() is called notifying applications
of a new Tx timestamp. Even a well behaved application sending only one
packet at a time and waiting for a response can wake up and send a new
packet before the bit lock is cleared. This results in needlessly
dropping some Tx timestamp requests.
We can fix this by unlocking the state bit as soon as we read the
Timestamp register, as this is the first point at which it is safe to
unlock.
To avoid issues with the skb pointer, we'll use a copy of the pointer
and set the global variable in the driver structure to NULL first. This
ensures that the next timestamp request does not modify our local copy
of the skb pointer.
This ensures that well behaved applications do not accidentally race
with the unlock bit. Obviously an application which sends multiple Tx
timestamp requests at once will still only timestamp one packet at
a time. Unfortunately there is nothing we can do about this.
Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ret_val instead of !ret_val to allow the rest of
the code to execute and configure the speed properly.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add RS1 configuration to ixgbe_set_soft_rate_select_speed()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the logic which would previously skip the link configuration
in the case where we are already at the requested speed in
ixgbe_setup_mac_link_multispeed_fiber().
By exiting early we are skipping the link configuration and as such
the driver may not always configure the PHY correctly for SFP+.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the writes are processed immediately. Without the flush it
is possible for operations on one port to spill over the other as the
resource is shared.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous method was unreliable. Use a different register to
differentiate between the SKUs.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds/changes fall through comments to address new warnings
produced by gcc 7.
Fixed formatting on a couple of comments in the function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following warning is now shown as a result of new checks added for
gcc 7:
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c: In function ‘ixgbe_open’:
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3118:13: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size between 3 and 18 [-Wformat-truncation=]
"%s-%s-%d", netdev->name, "TxRx", ri++);
^~
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3118:6: note: directive argument in the range [0, 2147483647]
"%s-%s-%d", netdev->name, "TxRx", ri++);
^~~~~~~~~~
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3117:4: note: ‘snprintf’ output between 8 and 32 bytes into a destination of size 24
snprintf(q_vector->name, sizeof(q_vector->name) - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-%s-%d", netdev->name, "TxRx", ri++);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Resolve this warning by making a couple of changes.
- Don't reserve space for the null terminator. Since snprintf adds the
null terminator automatically, there is no need for us to reserve a byte
for it.
- Change a couple variables that can never be negative from int to
unsigned int.
While we're making changes to the format string, move the constant strings
into the format string instead of providing them as specifiers.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, when setting a VF MAC address there are no error checks to
ensure that the MAC filter was successfully added. This patch adds
additional error checks, reporting, and propagation of errors. It also
will not set the MAC address unless adding the MAC filter was successful.
With these changes, setting the mac address to zeros can no longer call
ixgbe_set_vf_mac() as adding a zero MAC address filter is not valid.
Instead directly delete the filter and, if successful, clear the MAC
address.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The thermal sensor event logic is messed up, because it can execute
the code when there is no thermal event. The current logic is that
it will exit when !capable && !event whereas it really should exit
when !capable || !event. For one thing, it means that the service
task is doing too much work. It probably has some other symptoms as
well. So, correct the logic, simplifying to only execute when there
is a thermal event. The capable check is redundant.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This will ensure that VF-to-VF traffic on the same PF
is filtered to allow RSS operation.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since FW configures the PHY and MAC X550EM_X has no
PHY access, led_[on|off] is not supported with the 1Gbase-t design.
Removed MAC X550EM_X 1Gbase-t led_[on|off] support by setting
function pointers to NULL and added NULL pointer checks. Also set
init_led_link_act to NULL and added NULL pointer check.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch advertises TSO & GSO features in netdev->mpls_features.
In ixgbe(vf)_tso() where we set up segmentation offload, the IP
header will be the inner network header when eth_p_mpls() indicates
the Ethernet protocol is MPLS (UC or MC).
Suggested-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZEHmsAAoJEFmIoMA60/r88SgQAJbFddueb0+DfJ+USDud4b/Z
akfS+G1UAm+TgtMyh1wM49dHzFssp36uWJxtWI+bPqBzuy94PMCbz7JVUV28gX9G
tFhFuc5YH94I/3y85rbZnolb6uZN9MhLjzTFqDC9ilW6HFqmwK4t4wlHSCjQN1St
svLYvs2G6n6/VK3Fre7/wOvdZ1erG4Qod+kn5Tx3K5TQydmRlaSBfK+DRANuDBkM
KzGO7Bkc/Cx8hb9pHmaey/wxmNrrgmVjTtWrEnb2tEq833zP4h6GhUIJEKodMSi5
gXPNZgKlu3n5L592M0UCh4EoHejzkv9wrcsoDm+djmsc5Zg2Howq4kAdHP8k4hUG
0gt8n0ni9vhJN56jikrGi7cAdHCKSNnx2Ue/qTCbX0ncB3XUMuJxJwCsgW/6wa9f
oU7tRtTS03UltnKoFAcyYclS4TaSY4SA4ySaK6Hi+cRkdVFDdyHQYbHHNSU7MsA+
IS2tXvGoIdSYyrZMHSRcl2rRTfYQUkmPEvBF3LvqZr32M4mJMmUNAPLZaly373ZE
iwq0ZJlrLeM0cqdFIG3S60RtJyQk/HBN1NMqrYHArWOxvWIgNd5F8NCsTTxY3wU3
IxgBIuUFcbVwVkqEHGs8K5AvB3oghqdnA3eGOV79799eMtLn3LOvyIlpHMSw9WUq
ags00JtMLitfNPBH3eSl
=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
The RSS key is being repopulated every time the interface is brought up
regardless of whether there is an existing value. If the user sets the RSS
key and the interface is brought up (e.g. reset), the user specified RSS
key will be overwritten.
This patch changes the rss_key to a pointer so we can check to see if the
key has been populated and preserve it accordingly.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for new 1000Base-T device based on X550EM_X MAC
type. All PHY operations are disabled as the PHY is controlled
by FW.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, there is no logic that allows a VF's MAC address to be removed
from the RAR table.
Allow the user to specify a zero MAC address in order to clear the VF's
MAC address from the RAR table. This functionality is also utilized by
libvirt when removing VFs.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flush the macvlan filters on VF reset to avoid conflict with other VFs that
may end up using the same MAC address.
The main change here is the call to ixgbe_set_vf_macvlan() with index 0.
Moved ixgbe_set_vf_macvlan() in front of ixgbe_vf_reset_event() to avoid
adding a prototype.
Reported-by: Sritej Kanakadandi Sritej Rama <skanakad@cisco.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current XDP implementation hits the tail on every XDP_TX return
code. This patch changes driver behavior to only hit the tail after
packet processing is complete.
With this patch I can run XDP drop programs @ 14+Mpps and XDP_TX
programs are at ~13.5Mpps.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A couple design choices were made here. First I use a new ring
pointer structure xdp_ring[] in the adapter struct instead of
pushing the newly allocated XDP TX rings into the tx_ring[]
structure. This means we have to duplicate loops around rings
in places we want to initialize both TX rings and XDP rings.
But by making it explicit it is obvious when we are using XDP
rings and when we are using TX rings. Further we don't have
to do ring arithmatic which is error prone. As a proof point
for doing this my first patches used only a single ring structure
and introduced bugs in FCoE code and macvlan code paths.
Second I am aware this is not the most optimized version of
this code possible. I want to get baseline support in using
the most readable format possible and then once this series
is included I will optimize the TX path in another series
of patches.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Basic XDP drop support for ixgbe. Uses READ_ONCE/xchg semantics on XDP
programs instead of RCU primitives as suggested by Daniel Borkmann and
Alex Duyck.
v2: fix the build issues seen w/ XDP when page sizes are larger than 4K
and made minor fixes based on feedback from Jakub Kicinski
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent firmware change fixed an issue to acquire the PHY semaphore before
accessing PHY registers. This led to a case where SW can issue a device
reset clearing the MDIO registers. This patch makes SW acquire the PHY
semaphore before issuing a device reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I just found that when we had changed the Rx path to check for length
instead of the DD bit we introduced an issue in ixgbe_dump since we were no
longer clearing the status bits.
To correct this I am updating ixgbe_dump to look for the length bits in the
descriptor since that is what we are using in the Rx path.
Fixes: c3630cc40b ("ixgbe: Use length to determine if descriptor is done")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch increases the headroom allocated when using build_skb on a
system with 4K pages. Specifically the breakdown of headroom versus cache
size is as follows:
L1 Cache Size Headroom
64 192
64, NET_IP_ALIGN == 2 194
128 128
128, NET_IP_ALIGN == 2 130
256 512
256, NET_IP_ALIGN == 2 258
I stopped at supporting only a cache line size of 256 as that was the
largest cache size I could find supported in the kernel.
With this we are guaranteeing at least 128 bytes of headroom to spare in
the frame. This should be enough for us to insert a couple of IPv6 headers
if needed which is likely enough room for anything XDP should need.
I'm leaving the padding for systems with pages larger than 4K unmodified
for now. XDP currently isn't really setup to work on those types of
systems so we can cross that bridge when we get there.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We did not have a check in place for MMNGC.MNG_VETO when setting up link
on X550EM_X KR devices which resulted in link loss for the BMC when
loading the driver.
This patch adds a check for ixgbe_check_reset_blocked() in setup_link()
since in that case there is no PHY reset function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the Marvell 1145 PHY define as we have never had a device that
supports it and have no plan to in the future. The existence of this
define has caused confusing on whether or not this PHY was supported
by ixgbe.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid setting adapter->num_vfs early in the init code path when
using the max_vfs module parameter by passing it to ixgbe_enable_sriov()
as a function parameter.
This fixes an issue where if we failed to allocate vfinfo in
__ixgbe_enable_sriov() the driver will crash with NULL pointer in
ixgbe_disable_sriov() when attempting to free the vfinfo struct based
on adapter->num_vfs. Also it cleans up the assignment of adapter->num_vfs
since now it will only be set in __ixgbe_enable_sriov() and cleared in
ixgbe_disable_sriov().
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we exit at the end of the block, we can save a level of
indentation by performing an early return, and make the next several
sections of code more legible, with fewer 80 character line breaks.
Also moved allocating vfinfo at the beginning and the notification
for enabling SRIOV at the end of the function when we know that it
will succeed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the code allocating memory for list of MAC addresses that
the VFs can use for MACVLAN into its own function.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add default setting for mac->ops.setup_link on x550em_a MAC types.
This fixes a link issue on KR parts.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We forgot to indicate some of the supported speed on the X553
backplane. This patch attempts to correct for that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch add support for X552 XFI backplane interface. The XFI
backplane requires a custom tuned link. HW/FW owns the link config
for XF backplane and SW must not interfere with it.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The initial patches supporting X553 sgmii forgot some details. This patch
should cover those missing spots.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The KX4 PHY is configured by the NVM. Currently, the driver is overwriting
the config; remove the code associated with KX4 configuration.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
As pr_cont output can be interleaved by other processes,
using pr_cont should be avoided where possible.
Miscellanea:
- Use a temporary pointer to hold the next descriptions and
consolidate the pr_cont uses
- Use the temporary buffer to hold the 8 u32 register values and
emit those in a single go
- Coalesce formats and logging neatening around those changes
- Fix a defective output for the rx ring entry description when
also emitting rx_buffer_info data
This reduces overall object size a tiny bit too.
$ size drivers/net/ethernet/intel/ixgbe/*.o*
text data bss dec hex filename
62167 728 12 62907 f5bb drivers/net/ethernet/intel/ixgbe/ixgbe_main.o.new
62273 728 12 63013 f625 drivers/net/ethernet/intel/ixgbe/ixgbe_main.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When DCB is enabled, add checks to ensure creation of number of VF's is
valid based on the traffic classes configured by the device.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a typo that I had left in the code comments for the igb and ixgbe
functions that enabled build_skb support.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On architectures that have a cache line size larger than 64 Bytes we start
running into issues where the amount of headroom for the frame starts
shrinking.
The size of skb_shared_info on a system with a 64B L1 cache line size is
320. This increases to 384 with a 128B cache line, and 512 with a 256B
cache line.
In addition the NET_SKB_PAD value increases as well consistent with the
cache line size. As a result when we get to a 256B cache line as seen on
the s390 we end up 768 bytes used by padding and shared info leaving us
with only 1280 bytes to use for data storage. On architectures such as
this we should default to using 3K Rx buffers out of a 8K page instead of
trying to do 1.5K buffers out of a 4K page.
To take all of this into account I have added one small check so that we
compare the max_frame to the amount of actual data we can store. This was
already occurring for igb, but I had overlooked it for ixgbe as it doesn't
have strict limits for 82599 once we enable jumbo frames. By adding this
check we will automatically enable 3K Rx buffers as soon as the maximum
frame size we can handle drops below the standard Ethernet MTU.
I also went through and fixed one small typo that I found where I had left
an IGB in a variable name due to a copy/paste error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ixgbe_set_rxfh() updates the rss_key copy in the driver
memory, but does not push the new value into the h/w. This commit
add a new helper for the latter operation and call it in
ixgbe_set_rxfh(), so that the h/w rss key value can be really
updated via ethtool.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix typos and add the following to the scripts/spelling.txt:
applys||applies
The "applyes" in drivers/video/fbdev/aty/radeon_monitor.c is a different
pattern but it was fixed in this commit. The "This functions" in the
same line was fixed as well.
Link: http://lkml.kernel.org/r/1481573103-11329-24-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes it so that we don't need to bother with clearing the
memory out for the descriptor rings. The general idea is to only free
buffers associated with buffers in use which are located between the
next_to_clean and next_to_use or next_to_alloc values. Everything outside
of those regions can be safely ignored since they should have no buffers
associated with them.
The advantage to doing things this way is that is should speed up bring-up
and tear-down of the rings. Specifically we can avoid the 512 or more
cycles required to memset the rings in tear-down. In the bring-up phase we
then clear the memory as a part of initialization. The general idea is
that the clearing in initialization can act as a prefetch of sorts for the
buffer info structures so they are in the local CPU when we go to populate
them. This should help to improve overall time needed to perform a
suspend/resume.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds build_skb support to the Rx path. There are several
advantages to this change.
1. It avoids the memcpy and skb->head allocation for small packets which
improves performance by about 5% in my tests.
2. It avoids the memcpy, skb->head allocation, and eth_get_headlen
for larger packets improving performance by about 10% in my tests.
3. For VXLAN packets it allows the full header to be in skb->data which
improves the performance by as much as 30% in some of my tests.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since there are potential drawbacks to the new Rx allocation approach I
thought it best to add a "chicken bit" so that we can turn the feature off
if in the event that a problem is found.
It also provides a means of validating the legacy Rx path in the event that
we are forced to fall back. At some point in the future when we are
convinced we don't need it anymore we might be able to drop the legacy-rx
flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for providing a buffer with headroom and tailroom
to allow for shared info, NET_SKB_PAD, and NET_IP_ALIGN. With this
combined with the DMA changes we can start using build_skb to build frames
around an incoming Rx buffer instead of having to memcpy the headers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are going to be expanding the number of Rx paths in the driver. Instead
of duplicating all that code I am pulling it apart into separate functions
so that we don't have so much code duplication.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to support build_skb with jumbo frames it will be necessary to use
3K buffers for the Rx path with 8K pages backing them. This is needed on
architectures that implement 4K pages because we can't support 2K buffers
plus padding in a 4K page.
In the case of systems that support page sizes larger than 4K the 3K
attribute will only be applied to FCoE as we can fall back to using just 2K
buffers and adding the padding.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Batch the page count updates instead of doing them one at a time. By doing
this we can improve the overall performance as the atomic increment
operations can be expensive due to the fact that on x86 they are locked
operations which can cause stalls. By doing bulk updates we can
consolidate the stall which should help to improve the overall receive
performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING. By enabling both of these for the Rx path we are
able to see performance improvements on architectures that implement either
one due to the fact that page mapping and unmapping only has to sync what
is actually being used instead of the entire buffer. In addition by
enabling the weak ordering attribute enables a performance improvement for
architectures that can associate a memory ordering with a DMA buffer such
as Sparc.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some platforms, syncing a buffer for DMA is expensive. Rather than
sync the whole 2K receive buffer, only synchronise the length of the
frame, which will typically be the MTU, or a much smaller TCP ACK.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch consolidates the code for the ixgbe driver so that it is more
inline with what is already in igb. The general idea is to just
consolidate functions that represent logical steps in the Rx process so we
can later update them more easily.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver version to reflect the new devices that it
supports.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since dcbnl_ops is global, it should be prefixed by ixgbe_
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Though not advertised through ethtool, if the link partner advertises a
2.5Gb or 5Gb connection, and the adapter supports it, allow the speed to be
used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f24273837 ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f4 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dac ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relax ordering(RO) is one feature of 82599 NIC, to enable this feature can
enhance the performance for some cpu architecure, such as SPARC and so on.
Currently it only supports one special cpu architecture(SPARC) in 82599
driver to enable RO feature, this is not very common for other cpu architecture
which really needs RO feature.
This patch add one common config CONFIG_ARCH_WANT_RELAX_ORDER to set RO feature,
and should define CONFIG_ARCH_WANT_RELAX_ORDER in sparc Kconfig firstly.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the xcast mailbox message to include support for
unicast promiscuous mode. To allow a VF to enter this mode the PF
must be in promiscuous mode.
A later patch will add the support needed in the VF driver (ixgbevf)
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement support for devices that have firmware-controlled PHYs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement new interface for firmware commands to access some PHYs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware version method and functions are not used anywhere, so
remove them all.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two problems with EEPROM access. One is that it needs to
hold the semaphore until the entire response is read or else the
response can be corrupted by other firmware accesses. The second
problem is that acquiring and releasing the semaphore is slow, so
it should be taken and released once when multiple EEPROM accesses
will be done.
Both of these issues can be solved by adding a new function,
ixgbe_hic_unlocked, to issue firmware commands that will assume
that the caller has acquired the needed semaphore.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch ensures that the advertised link speeds are configured
for X553 KR/KX backplane. Without this patch the link remains at
1G when resuming from low power after being downshifted by LPLU.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rx timestamp does not work on 82599 and X540 because bitwise operation
of RX_HWTSTAMP flags is incorrect and ixgbe_ptp_rx_hwtstamp() is never
called. This patch fixes it to enable Rx timestamp on 82599 and X540.
Without this fix:
ptp4l[278.730]: selected /dev/ptp8 as PTP clock
ptp4l[278.733]: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l[278.733]: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l[278.834]: port 1: received SYNC without timestamp
ptp4l[278.835]: port 1: new foreign master 1c3947.fffe.60f9cc-1
ptp4l[279.834]: port 1: received SYNC without timestamp
ptp4l[280.834]: port 1: received SYNC without timestamp
ptp4l[281.834]: port 1: received SYNC without timestamp
ptp4l[282.834]: port 1: received SYNC without timestamp
ptp4l[282.835]: selected best master clock 1c3947.fffe.60f9cc
ptp4l[282.835]: port 1: LISTENING to UNCALIBRATED on RS_SLAVE
ptp4l[283.834]: port 1: received SYNC without timestamp
With this fix:
ptp4l[239.154]: selected /dev/ptp8 as PTP clock
ptp4l[239.157]: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l[239.157]: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l[240.989]: port 1: new foreign master 1c3947.fffe.60f9cc-1
ptp4l[244.989]: selected best master clock 1c3947.fffe.60f9cc
ptp4l[244.989]: port 1: LISTENING to UNCALIBRATED on RS_SLAVE
ptp4l[246.977]: master offset -899583339542096 s0 freq +0 path delay 16222
ptp4l[247.977]: master offset -899583339617265 s1 freq -75169 path delay 16177
ptp4l[248.977]: master offset -130 s2 freq -75299 path delay 16177
ptp4l[248.977]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[249.977]: master offset -9 s2 freq -75217 path delay 16177
ptp4l[250.977]: master offset 88 s2 freq -75123 path delay 16132
Fixes: a9763f3cb5 ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Yusuke Suzuki <yus-suzuki@uf.jp.nec.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure that we free the IRQs in ixgbe_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.
Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbe_remove() after a failed recovery from
AER error because the interrupts were not freed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two methods for setting mac addresses in a Macvlan, that
differentiate themselves in the function macvlan_set_mac_Address.
If the macvlan mode is passthru, then we use the dev_set_mac_address
method, otherwise we use the dev_uc api via macvlan_sync_addresses.
The latter method (which would stem from using any non-passthru mode,
like bridge, or vepa), calls down into the driver in a path that terminates
in ixgbevf_set_uc_addr_vf, which sends a IXGBE_VF_SET_MACVLAN message,
which causes the pf to spawn the noted error message. This occurs because
it appears that the guest is trying to delete the mac address of the macvlan
before adding another.
The other path in macvlan_set_mac_address uses dev_set_mac_address, which
calls into ixgbevf_set_mac which uses the IXGBE_VF_SET_MAC_ADDR to the
pf to set the macvlan mac address.
The discrepancy here is in the handlers. The handler function for
IXGBE_VF_SET_MAC_ADDR (ixgbe_set_vf_mac_addr) has a check for
the vfinfo[].trusted bit to allow the operation if the vf is trusted.
In comparison, the IXGBE_VF_SET_MACVLAN message handler
(ixgbe_set_vf_macvlan_msg) has no such check of the trusted bit.
Signed-off-by: Ken Cox <jkc@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an interface is part of a namespace it is possible that
ixgbe_close() may be called while __ixgbe_shutdown() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs().
To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and ixgbe_clear_interrupt_scheme()
in __ixgbe_shutdown() and check for netif_device_present()
to avoid clearing the interrupts second time in ixgbe_close();
Also extend the rtnl lock in ixgbe_resume() to netif_device_attach().
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BaseT adapters that are capable of supporting 100Mb are not reporting this
capability. This patch corrects the reporting so that 100Mb is shown as
supported on those adapters.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A retry count of 10 is likely to run into problems on X550 devices that
have to detect and reset unresponsive CS4227 devices. So, reduce the I2C
retry count to 3 for X550 and above. This should avoid any possible
regressions in existing devices.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is an extension of commit 003287e0f0 ("ixgbevf: Correct parameter
sent to LED function"); add bounds checking to x540 functions to ensure the
index is valid.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The indirection table was reported incorrectly for X550 and newer
where we can support up to 64 RSS queues.
Reported-by Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The generic PHY reset check we had previously is not sufficient for the
ixgbe_phy_x550em_ext_t PHY type. Check 1.CC02.0 instead - same as
ixgbe_init_ext_t_x550().
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some x550 devices require the driver version reported to its firmware; this
patch sends the driver version string to the firmware through the host
interface command for x550 devices.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FEC is configured by the NVM and the driver should not be
overriding it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of IPIP and SIT tunnel frames the outer transport header
offset is actually set to the same offset as the inner transport header.
This results in the lco_csum call not doing any checksum computation over
the inner IPv4/v6 header data.
In order to account for that I am updating the code so that we determine
the location to start the checksum ourselves based on the location of the
IPv4 header and the length.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some Tx paths (e.g., tpacket_snd()), ixgbe_atr may be
passed down an sk_buff that has the network and transport
header in the paged data, so it needs to make sure these
headers are available in the headlen bytes to calculate the
l4_proto.
This patch expect that network and transport headers are
already available in the non-paged header dat. The assumption
is that the caller has set this up if l4_proto based Tx
steering is desired.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 9f12df906c ("ixgbe: Store VXLAN port number in network order")
incorrectly checks for hdr.ipv4->protocol != IPPROTO_UDP
in ixgbe_atr(). This check should be for "==" instead.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were using an old Alpha version of the X550 phy ID. This was leading
to unnecessary queries of the PHY. I removed the old ID (which shouldn't
be on any HW) and add the two that are.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch add X553 FW ALEF support for B0. ALEF is the new unified
FW. This contains updated register defines for ALEF speed
configuration. Likewise it also removes the AN_CNTL_8 usage from
the native SFI flow as it is no longer supported by FW.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix an issue where set_phy_power was NULL for X550 copper devices
because get_invariants was called before hw->device_id was set.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce ixgbe_link_operations struct with the following changes:
read_i2c_combined => read_link
read_i2c_combined_unlocked => read_link_unlocked
write_i2c_combined => write_link
write_i2c_combined_unlocked => write_link_unlocked
This will allow X550EM_a to override these methods for MDIO access
while X550EM_x provides methods to use I2C combined access. This
also adds a new structure, ixgbe_link_info, to hold information
about the link. Initially this is just method pointers and a bus
address.
The functions involved in combined I2C accesses were moved from
ixgbe_phy.c to ixgbe_x550.c. The underlying functions that carry
out the combined I2C accesses were left in ixgbe_phy.c because
they share some functions with other I2C methods.
v2 - set hw->link.ops in probe.
v3 - check ii->link_ops before setting it since we don't have it
for all devices.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove SFP ixfi code since there is no HW that currently supports it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The msix_entries memory can be freed by a previous suspend or
remove, so don't crash on close when it isn't there.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds X553 flow control auto negotiation for fiber and
backplain. To enable this new function pointers were added as well
as creating a function to dynamically set function pointer we can't
define only on MAC type.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Read the PHY register twice in order to get the correct value for
autoneg_status.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace some ixgbe specific MDIO defines with their equivalent
from the kernel.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates ixgbe_setup_phy_link_generic to set/unset
auto-negotiation for all speeds. This ensures that unsupported
speeds are unset. This is necessary since the PHY NVM may
advertise unsupported speeds.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support to get the LED link active via the LEDCTL
register. If the LEDCTL register does not have LED link active
(LED mode field = 0x0100) set then default LED link active returned.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X553 doesn't need all the initialization that X552 did for iXFI. This
patch will allow native SPI SFP+ to work with X553 devices. Future
patches will add additional configuration as needed.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NULL pointer dereference in the case where a macvlan interface is
brought up while the PF is still down:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: [<ffffffffa0170fb2>] ixgbe_alloc_rx_buffers+0x42/0x1a0 [ixgbe]
Call Trace:
[<ffffffffa017336b>] ixgbe_configure_rx_ring+0x2eb/0x3d0 [ixgbe]
[<ffffffffa0173811>] ixgbe_fwd_ring_up+0xd1/0x380 [ixgbe]
[<ffffffffa0179709>] ixgbe_fwd_add+0x149/0x230 [ixgbe]
[<ffffffffa0113480>] macvlan_open+0x260/0x2b0 [macvlan]
Reported-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert ixgbe users to new dev walk API. This is just a code conversion;
no functional change is intended.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
and no longer serves a purpose. No need to set min_mtu or max_mtu
explicitly, as ether_setup() will already set them to 68 and 1500.
e1000: min_mtu 46, max_mtu 16110
e1000e: min_mtu 68, max_mtu varies based on adapter
fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now
i40e: min_mtu 68, max_mtu 9706
i40evf: min_mtu 68, max_mtu 9706
igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
the driver, the larger value wasn't relevant though, so I've set max_mtu
to the smaller of the two values here to retain identical behavior.
igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated
ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu
ixgbe: min_mtu 68, max_mtu 9710
ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These accessors are used in various drivers that support tc offloading,
to detect properties of a given 'tc_action'.
'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR.
'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR.
As a prep towards supporting INGRESS redir/mirror, rename these
predicates to reflect their true meaning:
s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/
s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-09-23
This series contains updates to ixgbe and ixgbevf.
Emil provides several changes, first simplifies the logic for setting VLAN
filtering by checking the VMDQ flag and the old 82598 MAC, instead of
having to maintain a list of MAC types. Then made two functions static
that are used only within the file, a by-product is sparse is now happy.
Added spinlocks to make sure that the MTU configuration is handled
properly. Fixed an issue where when SR-IOV is enabled while the
ixgbevf driver is loaded would result in all mailbox requests being
rejected by ixgbe, so call ixgbe_sriov_reinit() before pci_enable_sriov()
to ensure mailbox requests are properly handled.
Mark resolves a NULL pointer issue by simply setting the read and write
*_ref_mdi pointers for x550em_a devices. Then clearly indicates within
ethtool that all MACs support pause frames and made sure that the
advertising is set to the requested mode. Fixed an issue where
MDIO_PRTAD_NONE was not being used consistently to indicate no PHY
address.
Alex fixes an issue, where the support for multiple queues when SR-IOV
is enabled was added but the support was not reported. With that, fix
an issue where the hardware redirection table could support more queues
then the PF currently has when SR-IOV is enabled, so use the RSS mask to
trim off the bits that are not used. Lastly, instead of limiting the
VFs if we do not use 4 queues for RSS in the PF, we can instead just limit
the RSS queues used to a power of 2. We can now support use cases where
VFs are using more queues than the PF is currently using and can support
RSS if so desired.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling SRIOV while the ixgbevf driver is loaded will result in all
mailbox requests from ixgbevf_open() being rejected by ixgbe because
adapter->clear_to_send is set to false on reset.
Call ixgbe_sriov_reinit() before pci_enable_sriov() to make sure that
mailbox requests are handled from the time ixgbevf is loaded.
Reported-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of limiting the VFs if we don't use 4 queues for RSS in the PF we
can instead just limit the RSS queues used to a power of 2. By doing this
we can support use cases where VFs are using more queues than the PF is
currently using and can support RSS if so desired.
The only limitation on this is that we cannot support 3 queues of RSS in
the PF or VF. In either of these cases we should fall back to 2 queues in
order to be able to use the power of 2 masking provided by the psrtype
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware redirection table can support more queues then the PF
currently has when SR-IOV is enabled. In order to account for this use the
RSS mask to trim of the bits that are not used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The maximum queue count reported was 1, however support for multiple queues
with SR-IOV was added some time ago so we should report support for it to
the user so that they can select multiple queues if they so desire.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The value MDIO_PRTAD_NONE should be used to indicate no PHY address.
Not 0, not 0xFFFF. Use the MDIO_PRTAD_NONE value consistently.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All the MACs supported by ixgbe support pause frames, so indicate
that support in ethtool. Also set advertising according to requested
mode.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the read_reg_mdi and write_reg_mdi method pointers for
X550EM_A_10G_T devices to resolve jumping to NULL.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions are only used in ixgbe_x550.c.
Fixes a warning when compiling with -Wmissing-prototypes
Reported-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simplify the logic for setting VLNCTRL.VFE by checking the VMDQ flag
and 82598 MAC instead of having to maintain a list of MAC types.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers must be ready to accept NULL from ptp_clock_register() if the
PTP clock subsystem is configured out.
This patch documents that and ensures that all drivers cope well
with a NULL return.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Eugenia Emantayev <eugenia@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless log message and improve the logic for setting
a PHY address from the contents of the MNG_IF_SEL register.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the new copper device X557.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This shouldn't matter as nothing should be attached still to be
consisted control MDIO speed for these devices as well.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X557 devices use a different interface to the LED for the port.
This patch reflect that change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add geneve Rx offload support for x550em_a.
The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.
Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().
Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The RAR entry for the SAN MAC address was being cleared when we were
clearing the VMDq pool bits. In order to prevent this we need to add
an extra check to protect the SAN MAC from being cleared.
Fixes: 6e982aeae ("ixgbe: Clear stale pool mappings")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use atomic bitwise operations when setting and checking reset
requests. This should help with possible races in the service task.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a write the TXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.
The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.
Fixes: a85a970af2 ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit. This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV. This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.
Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.
Fixes: 1636956491 ("ixgbe: Add support for VLAN promiscuous with SR-IOV")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-07-22
This series contains updates to ixgbe and ixgbevf only.
Emil fixes the NACK check in ixgbevf_set_uc_addr_vf() for instances where
the index is not equal to zero. Fixes an issue where mac->ops.setup_fc
can be NULL for backplanes which can cause the driver to crash on load.
Don fixes the second parameter of the LED functions, which is the index to
the LED we are interested in affecting. Fixed variable to store register
reads to unsigned integer. Adds support for the new x553 hardware into
ixgbevf. Fixed a missing rtnl lock around ixgbevf_reinit_locked().
Fixed an issue where in ixgbevf_reset_subtask() was not verifying that
the port has been removed. Cleans up the initial crosstalk fix, since
the SFP that indicates the presence of a SFP+ module changes between
hardware types.
Babu Moger fixes typo in freeing IRQ, since the array subscript increments
after the execution of the statement.
Wei Yongjun adds the missing destroy_workqueue() before returning from
ixgbe_init_module() in the error handling case.
Tony adds range checking for setting the MTU from the VF, where the PF can
return a NACK but this was not passed on to the VF, so propagate the
results from the PF to the VF so errors can be reported. Consolidates
mailbox read and write functions, since the recent changes to
ixgbevf_write_msg_read_ack(), other functions are performing the same
operations done here.
Colin Ian King removes a redundant check on ret_val, since ret_val has
not changed since the previous check.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch address a few issues with the initial crosstalk fix. Most
important of which is the SDP that indicates the presents of a SFP+
module changes between HW types. With this change that is taken in
to consideration
It also moves the check closer to the base code that checks link. This
makes it so we only need to do the check in one spot.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The last check on ret_val is redundant since ret_val has not changed
since the previous check, so remove it as it is extraneous.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing destroy_workqueue() before return from
ixgbe_init_module() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
mac->ops.setup_fc can be null for backplanes which can cause the driver
to crash on load.
Reported-by: Patrick McLean <patrickm@gaikai.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The array subscript increments after the execution of the statement.
So there is no issue here. However it helps to read the code better.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I noticed this variable used for register reads wasn't an unsigned
so this patch corrects that. I don't believe this was causing any
issue as is but this is more consistent with the rest of the driver.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The second parameter of these functions is the index to the led we
are interested in affecting. However we were mistakenly passing
the offset in the register. This patch corrects that and adds some
bonds checking which would hopefully make bugs like this more noticeable
in the future.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the function ixgbe_poll() returns 0 when it clean completely
the rx rings, but this foul budget accounting in core code.
Fix this returning the actual work done, capped to weight - 1, since
the core doesn't allow to return the full budget when the driver modifies
the napi status
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some comments weren't updated to reflect the renaming of ndo's and the
change of arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting spoofing, both VLAN and MAC need to be set together.
This change resolves an issue where MAC-VLANs on the VF fail to pass
traffic due to spoofed packets.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ixgbe_ethtool_get_ts_info() to show that x550 supports hardware
timestamping of all packets.
Reported-by: Guy Harris <guy@alum.mit.edu>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For u32 classifier filters, avoid overwriting existing filter
in a hardware location without removing it first, to clean up
inconsistencies due to duplicate values for filter location.
Verified with the following filters:
Create child hash tables:
handle 1: u32 divisor 1
handle 2: u32 divisor 1
Link to the child hash table from parent hash table:
handle 800:0:11 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 6 ff match ip dst 15.0.0.1/32
handle 800:0:12 u32 ht 800: link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 17 ff match ip dst 16.0.0.1/32
Add filter into child hash table:
handle 1:0:3 u32 ht 1: \
match tcp src 22 ffff action drop
Add another filter to the same location:
handle 2:0:3 u32 ht 2: \
match tcp src 33 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On deleting filters which are links to a child hash table, the filters
in the child hash table must be cleared from the hardware if there
is no link between the parent and child hash table.
Verified with the following filters:
Create a child hash table:
handle 1: u32 divisor 1
Link to the child hash table from parent hash table:
handle 800:0:10 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 6 ff match ip dst 15.0.0.1/32
Add filters into child hash table:
handle 1:0:2 u32 ht 1: \
match tcp src 22 ffff action drop
handle 1:0:3 u32 ht 1: \
match tcp src 33 ffff action drop
Delete link filter from parent hash table:
handle 800:0:10 u32
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the Intel ethernet drivers.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
In addition I updated the socket address family check so that instead of
excluding IPv6 we instead abort of type is not IPv4. This makes much more
sense as we should only be supporting IPv4 outer addresses on this
hardware.
The last change is that I pulled the rtnl_lock/unlock into the conditional
statement for IXGBE_FLAG2_VXLAN_REREG_NEEDED. The motivation behind this
is to avoid unneeded bouncing of the mutex which will just slow down the
handling of this call anyway.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading IPXIP6 type packets that represent
either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header. In
addition with this change we should also be able to support FOU
encapsulated traffic with outer IPv6 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like at some point I somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features. As a result the driver is now generating a warning about
vlan_features being setup incorrectly.
This patch corrects that by placing the update of netdev->features to
include the VLAN features so that it is after the point where we write
netdev->features into netdev->vlan_features.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Swap the parameters in GENMASK in order to generate the correct mask.
This change fixes Tx hangs when enabling SRIOV.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-05-04
This series contains updates to ixgbe, ixgbevf and traffic class helpers.
Sridhar adds helper functions to the tc_mirred header to access tcf_mirred
information and then implements them for ixgbe to enable redirection to
a SRIOV VF or an offloaded MACVLAN device queue via tc 'mirred' action.
Amritha adds support to set filters with multiple header fields (L3,L4)
to match on.
KY Srinivasan from Microsoft add Hyper-V support into ixgbevf.
Emil adds 82599 sub-device IDs that were missing from the list of parts
that support WoL. Then simplified the logic we use to determine WoL
support by reading the EEPROM bits for MACs X540 and newer.
Preethi cleaned up duplicate and unused device IDs. Fixed our ethtool
stat reporting where we were ignoring higher 32 bits of stats registers,
so fill out 64 bit stat values into two 32 bit words.
Babu Moger from Oracle improves VF performance issues on SPARC.
Alex Duyck cleans up some of the Hyper-V implementation from KY so that
we can just use function pointers instead of having to identify if a
given VF is running on a Linux or Windows PF.
Usha makes sure that DCB and FCoE is disabled for X550EM_x/a MACs and
cleans up the DCB initialization in the process.
Tony cleans up the API for ixgbevf_update_xcast_mode() so we do not
have to pass in the netdev parameter, since it was never used in the
function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
a trans_start struct member exists twice:
- in struct net_device (legacy)
- in struct netdev_queue
Instead of open-coding dev->trans_start usage to obtain the current
trans_start value, use dev_trans_start() instead.
This is not exactly the same, as dev_trans_start also considers
the trans_start values of the netdev queues owned by the device
and provides the most recent one.
For legacy devices this doesn't matter as dev_trans_start can cope
with netdev trans_start values of 0 (they are ignored).
This is a prerequisite to eventual removal of dev->trans_start.
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IXGBE_FLAG_DCB_CAPABLE flag that is set
for all MACs other than X550EM_x and x550em_a. DCB and
FCoE is disabled for these MACS. DCB initialization
code is moved to a separate function.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Revise populating few registers in ixgbe_get_regs() and macro
definitions.
Before applying patch:
$ du -k objs/drivers/net/ethernet/intel/ixgbe/ixgbe.ko
8572 objs/drivers/net/ethernet/intel/ixgbe/ixgbe.ko
After applying patch:
$ du -k objs/drivers/net/ethernet/intel/ixgbe/ixgbe.ko
8568 objs/drivers/net/ethernet/intel/ixgbe/ixgbe.ko
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code was ignoring higher 32 bits of stats registers. This patch
correctly fills out 64 bit value in two 32 bit words.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove duplicate and unused device ID definitions.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change aims to simplify the logic we use to determine WOL
support by reading the EEPROM bits for MACs X540 and newer.
Also some cleanups in ixgbe_wol_supported() - changed return type to
bool and removed redundant return variable by simply using return after
the checks.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We had some 82599 subdevice IDs missing from the list of parts that
support WoL.
Reported-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds support to set filters with multiple header fields (L3,L4)to match on.
This is achieved in the following order:
1. Create a leaf hash table for the next header.
2. Create a link to the leaf hash table from the base hash table with
matches on next header type and current header fields.
3. Add filter in leaf hash table with match on next header fields and
action.
Verified with the following filters :
Match TCP and DIP:
handle 1: u32 divisor 1
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 6 ff match ip dst 10.0.0.1/32
match tcp src 28 ffff action drop
Delete the filter:
Match on DIP, SIP, UDP (SPort, DPort):
handle 2: u32 divisor 1
u32 ht 800: order 2 link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip dst 15.0.0.2/32 match ip protocol 17 ff \
match ip src 15.0.0.1/32
match udp src 30 ffff match udp dst 32 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables 'redirect' to a SRIOV VF or a offloaded macvlan
device queue via tc 'mirred' action.
Verified with the following script that creates SRIOV VFs, offloaded
macvlan and adds tc u32 filters with redirect action to the associated
netdevs.
# add ingress qdisc.
tc qdisc add dev p4p1 ingress
# enable hw tc offload.
ethtool -K p4p1 hw-tc-offload on
# create 4 sriov VFs and bring up the first one.
echo 4 > /sys/class/net/p4p1/device/sriov_numvfs
sleep 1
ip link set p4p1 up
ip link set p4p1_0 up
# create a offloaded macvlan device and bring it up.
ethtool -K p4p1 l2-fwd-offload on
ip link add link p4p1 name mvlan_1 type macvlan
ip link set mvlan_1 up
# add u32 filter with action to redirect to VF netdev
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: \
match ip src 192.168.1.3/32 \
action mirred egress redirect dev p4p1_0
# add u32 filter with action to redirect to macvlan netdev
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: \
match ip src 192.168.2.3/32 \
action mirred egress redirect dev mvlan_1
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The newly added x550em_a support causes a link failure on ARM because of
an overly long time passed into udelay():
ERROR: "__bad_udelay" [drivers/net/ethernet/intel/ixgbe/ixgbe.ko] undefined!
There are multiple variants of the ixgbe_acquire_swfw_sync_*() function,
and the other ones all use msleep(), so we can safely assume that all
callers are allowed to sleep, which makes msleep() a better replacement
than mdelay().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 49425dfc74 ("ixgbe: Add support for x550em_a 10G MAC type")
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for partial GSO segmentation in the case of
tunnels. Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header. This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make use of GENMASK instead of open coding the equivalent operation
incorrectly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several areas of ixgbe were written before widespread usage of the
BIT(n) macro. With the impending release of GCC 6 and its associated new
warnings, some usages such as (1 << 31) have been noted within the ixgbe
driver source. Fix these wholesale and prevent future issues by simply
using BIT macro instead of hand coded bit shifts.
Also fix a few shifts that are shifting values into place by using the
'u' prefix to indicate unsigned. It doesn't strictly matter in these
cases because we're not shifting by too large a value, but these are all
unsigned values and should be indicated as such.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible on some systems that crosstalk could lead to link flap
on empty SFP+ cages. A new NVM bit was defined to let SW know it
needs to implement the work around which consists of verifying that
there is a module in the cage before acting on the LSC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Somehow the wrong fc_setup function was used for x550em_a, so
correct that. Also set setup_link to NULL as its value is
determined later, just like it is with X550EM_x.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a new register to wait for previous register writes to complete
before issuing a register read. This is needed when slower links
are in use.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This field is used to record the RX queue index for a redirect action
passed via ring_cookie field in struct ethtool_rx_flow_spec which is
a u64 value.
For ex: after adding a filter rule to redirect to a VF using ethtool
# echo 4 > /sys/class/net/p4p1/device/sriov_numvfs
# ethtool -N p4p1 flow-type ip4 src-ip 192.168.0.1 action 0x100000000
querying for the rule shows the Action as 'Direct to queue 0'
# ethtool -n p4p1
4 RX rings available
Total 1 rules
Filter: 2045
Rule Type: Raw IPv4
Src IP addr: 192.168.0.1 mask: 0.0.0.0
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Protocol: 0 mask: 0xff
L4 bytes: 0x0 mask: 0xffffffff
VLAN EtherType: 0x0 mask: 0xffff
VLAN: 0x0 mask: 0xffff
User-defined: 0x0 mask: 0xffffffffffffffff
Action: Direct to queue 0
With this fix, ethtool will report the right queue index even for VFs.
Action: Direct to queue 4294967296
Here 4294967296 corresponds to 0x100000000.
We need to update 'ethtool' to report the queue index as a Hex value so
that it is more user friendly and matches with the 'action' value that
is passed when adding the rule.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550EM_a/x did not have a default value for mac->ops.setup_link which
was causing link issues for backplane devices.
This patch sets mac->ops.setup_link to ixgbe_setup_mac_link_X540 for
X550EM_a/x which is also default for X550. This will result in
mac->ops.setup_link calling the link setup function for the respective
PHY type in case we do not need a special function to deal with it.
Reported-by: Ken Cox <jkc@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously the PF driver would only set VLAN spoof checking if
the VF had created VLANs. This was done by setting and checking
a counter (vlan_count) whenever a VLAN was created by the VF.
However it is possible for the vlan_count to be !=0 while there are
no VLANs assigned to the VF due to the count incrementing every
time a VLAN 0 is added on ifdown/up, which resulted in VLAN spoofing
always being set for those VFs.
This patch cleans up the logic by unconditionally setting VLAN based on
how the VF is configured (via ip link set ethX vf Y spoofchk on/off).
This change also resolves an issue where the VLAN spoofing can remain
set even after being disabled by the user due to the driver enabling
VLAN spoof checking every time a VLAN is added to the VF, but would
only allow changes in the setting if vlan_count != 0.
Also default_vf_vlan_id and vlans_enabled were removed from the
vf_data_storage structure since they are not being used in the driver.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Consolidate the logic behind configuring spoof checking:
Move the setting of the MAC, VLAN and Ethertype spoof checking into
ixgbe_ndo_set_vf_spoofchk().
Change ixgbe_set_mac_anti_spoofing() to set MAC spoofing per VF similar
to the VLAN and Ethertype functions - this allows us to call the helper
functions in ixgbe_ndo_set_vf_spoofchk() for all spoof check types and
only disable MAC spoof checking when creating MACVLAN.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
vxlan_get_rx_port requires rtnl_lock to be held.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ixgbe version number.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for x550em_a-based KR backplane devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for an SGMII backplane interface.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for SFPs with an external retimer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move code that controls MDIO speed into a new function because
there will be more MACs that need the control.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Read the IXGBE_NW_MNG_IF_SEL register and use it to set interface
attributes.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Read the instance number from EEPROM and save it for later use.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now x550em_a devices will use a new method for PHY access that will
get the firmware token for each access.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for x550em_a 10G MAC type to the ixgbe driver. The new
MAC includes new firmware commands that need to be used to control
PHY and IOSF access, so that support is also added. The interface
supported is a native SFP+ interface.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provide method pointers and use them to access IOSF-attached
devices. A new MAC will introduce a new access method.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add definitions for a x550em_a 10G MAC device with a native SFP
interface.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for a single-port X550 device.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables bulk free in Tx cleanup for ixgbevf and cleans up the
boolean logic in the polling routines for ixgbe and ixgbevf in the hopes of
avoiding any mix-ups similar to what occurred with i40e and i40evf.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to take the manageability semaphore when issuing firmware
commands to avoid problems. With this in place, the semaphore is
no longer taken in the ixgbe_set_fw_drv_ver_generic function, since
it will now always be taken by the ixgbe_host_interface_command
function.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up the interface for issuing firmware commands to use a
void * instead of a u32 *. This eliminates a number of casts.
Also clean up ixgbe_host_interface_command in a few other ways,
eliminating comparisons with 0, redundant parens and minor
formatting issues.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ixgbe_host_interface_command actually uses a multiple
of word sized buffer to do its business, but only checks against
the actual length passed in. This means that on read operations it
could be possible to modify locations beyond the length passed in.
Change the check to round up in the same way, just to avoid any
possible hazard.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the lan_id and func fields only ever hold small values, make
them u8 to avoid casts used to silence warnings.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I noticed the SRAMREL registers are not referenced for any device,
so delete the definitions.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can use the ethtool rx-vlan-filter flag to
toggle Rx VLAN filtering on and off. This is basically just an extension
of the existing VLAN promisc work in that it just adds support for the
additional ethtool flag.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added support to match on UDP fields in the transport layer.
Extended core logic to support multiple headers.
Verified with the following filters :
handle 1: u32 divisor 1
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
u32 ht 1: order 2 \
match tcp src 1024 ffff match tcp dst 23 ffff action drop
handle 2: u32 divisor 1
u32 ht 800: order 3 link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 17 ff
u32 ht 2: order 4 \
match udp src 1025 ffff match udp dst 24 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible on some HW that a system reset could occur when we are
holding the SWFW semaphore lock. So next time the driver was loaded we
would see it incorrectly as locked. This patch will recover from that state
by: Attempting to acquire the semaphore and then regardless of whether or
not it was acquire we immediately release it. This will force us into
a known good state.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit adds a callback which allows to adjust the maximum transmit
bitrate the card can output. This makes it possible to get a smooth
traffic instead of the default burst-y behaviour when trying to output
e.g. a video stream.
Much of the logic needed to get a correct bcnrc_val was taken from the
ixgbe_set_vf_rate_limit() function.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Xeon D KR backplane is different from other backplanes,
in that we can't use auto-negotiation to determine the
mode. Instead, use whatever the user configured.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for generic Tx checksums to the ixgbe driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit converts commit c762dff24c ("ixgbe: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d10549 ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The source for the ops structure contents are const, so make them
so. Copy them in place with structure assignments instead of memcpys.
Make the mbx_ops accessed by reference instead of making a copy of
the source structure. Update copyright date on the touched files.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were adding VLAN 0 twice each time we restored the VLAN configuration.
Instead of doing it twice we can just start working through the active
VLANs from ID 1 on and skip the double write.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While doing the work on igb I realized there were a few cases where we were
still adding VLANs to the VLVF entries for the PF when they were not
needed. This patch cleans that up so that the only time we add a PF entry
to the VLVF is either for VLAN 0 or if the PF has requested a VLAN that a VF
is already using.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When running certain routing protocols like VRRP, VF guests need the
ability to set the unicast address of the interface. Extend the new ndo
trust feature to let the hypervisor trust a guest to set/update its own
unicast address.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It seem to be non intentionally changed to Tx in
commit adc810900a ("ixgbe: Refactor busy poll socket code to address
multiple issues")
Lock is taken from ixgbe_low_latency_recv, and there under this
lock we use ixgbe_clean_rx_irq so it looks wrong for me to increment
Tx counter.
Yield stats can be shown through ethtool:
ethtool -S enp129s0 | grep yield
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix support for 16 bit source/dest port matches in ixgbe model.
u32 uses a single 32-bit key value for both source and destination ports
starting at offset 0. So replace the 2 functions with a single function
that takes this key value/mask to program both source and dest ports.
Verified with the following filter:
#tc qdisc add dev p4p1 ingress
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1: u32 divisor 1
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:10 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:10 u32 ht 1: \
match tcp src 1024 ffff match tcp dst 80 ffff action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:11 u32 ht 1: \
match tcp src 1025 ffff action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:12 u32 ht 1: \
match tcp dst 81 ffff action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field
Verified with the following filters:
#tc qdisc add dev p4p1 ingress
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: \
match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: \
match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:3 u32 ht 800: \
match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:4 u32 ht 800: \
match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).
Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use udelay instead of usleep_range because this can be called while
a lock is held.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through. However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket. As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.
In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP. In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR. This way we can avoid
having to do any byte swaps in order to validate the port number.
I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct. This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.
In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read. I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit c9f53e63c2 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.
This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original series drivers would get offload requests for cls_u32
rules even if the feature bit is disabled. This meant the driver had
to do a boiler plate check on the feature bit before adding/deleting
the rule.
This patch lifts the check into the core code and removes it from the
driver specific case.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 9d35cf062e ("net: ixgbe: add minimal parser details for ixgbe")
Reported-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I incorrectly used __u32 types where we should be using u32 types when
I added the ixgbe_model.h file.
Fixes: 9d35cf062e ("net: ixgbe: add minimal parser details for ixgbe")
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures ixgbe will not try to offload hash tables from the
u32 module. The device class does not currently support this so until
it is enabled just abort on these tables.
Interestingly the more flexible your hardware is the less code you
need to implement to guard against these cases.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds initial support for offloading the u32 tc classifier. This
initial implementation only implements a few base matches and actions
to illustrate the use of the infrastructure patches.
However it is an interesting subset because it handles the u32 next
hdr logic to correctly map tcp packets from ip headers using the ihl
and protocol fields. After this is accepted we can extend the match
and action fields easily by updating the model header file.
Also only the drop action is supported initially.
Here is a short test script,
#tc qdisc add dev eth4 ingress
#tc filter add dev eth4 parent ffff: protocol ip \
u32 ht 800: order 1 \
match ip dst 15.0.0.1/32 match ip src 15.0.0.2/32 action drop
<-- hardware has dst/src ip match rule installed -->
#tc filter del dev eth4 parent ffff: prio 49152
#tc filter add dev eth4 parent ffff: protocol ip prio 99 \
handle 1: u32 divisor 1
#tc filter add dev eth4 protocol ip parent ffff: prio 99 \
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
#tc filter add dev eth4 parent ffff: protocol ip \
u32 ht 1: order 3 match tcp src 23 ffff action drop
<-- hardware has tcp src port rule installed -->
#tc qdisc del dev eth4 parent ffff:
<-- hardware cleaned up -->
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an ixgbe data structure that is used to determine what
headers:fields can be matched and in what order they are supported.
For hardware devices this can be a bit tricky because typically
only pre-programmed (firmware, ucode, rtl) parse graphs will be
supported and we don't yet have an interface to change these from
the OS. So its sort of a you get whatever your friendly vendor
provides affair at the moment.
In the future we can add the get routines and set routines to
update this data structure. One interesting thing to note here
is the data structure here identifies ethernet, ip, and tcp
fields without having to hardcode them as enumerations or use
other identifiers.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an opportunity to bulk free SKBs during reclaiming of
resources after DMA transmit completes in ixgbe_clean_tx_irq. Thus,
bulk freeing at this point does not introduce any added latency.
Simply use napi_consume_skb() which were recently introduced. The
napi_budget parameter is needed by napi_consume_skb() to detect if it
is called from netpoll.
Benchmarking IPv4-forwarding, on CPU i7-4790K @4.2GHz (no turbo boost)
Single CPU/flow numbers: before: 1982144 pps -> after : 2064446 pps
Improvement: +82302 pps, -20 nanosec, +4.1%
(SLUB and GCC version 5.1.1 20150618 (Red Hat 5.1.1-4))
Joint work with Alexander Duyck.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now ATR is not handling IPv6 extended headers, so ATR is not
being performed on such packets. Fix that by skipping extended
headers when they are present. This also fixes a problem where
the ATR code was not checking that the inner protocol was actually
TCP before setting up the signature rules. Since the protocol check
is intimately involved with the extended header processing as well,
this all gets fixed together.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When FCoE is enabled with SR-IOV on the X550 NIC the hardware
generates MDD events.
This patch fixes these by setting the expected values in the
Tx context descriptors for FCoE/FIP frames and adding a flush
after writing the RDLEN register.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check whether the FCOE support is enabled for the devices to get the
FDMI HBA attributes information instead of checking each device id.
Also, add Model string information for X550.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an outer UDP checksum is set, pass the skb up with CHECKSUM_NONE
so that the stack will check the checksum. Do not increment an
error counter, because we don't know that there is an actual error.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_get_settings() the link status and speed of the interface
are determined based on a read from the LINKS register via the call
to mac.ops.check.link(). This can cause issues where external drivers
may end up with unknown speed when calling ethtool_get_setings().
Instead of calling the mac.ops.check_link() we can report the speed
from the adapter structure which is populated by the driver.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PFC is configuration is skipped for X550 devices due to a incorrect
device id check, fixing that to include X550 PFC configuration.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use fcoe_ddp_xid from netdev as this is correctly set for different
device IDs to avoid DDP skip error on X550 as "xid=0x20b out-of-range"
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently credit_refill and credit_max could be zero for a TC and that
is causing Tx hang for CEE mode configuration, so to fix that have at
min credit assigned to a TC and that is as what IEEE mode already does.
Change-ID: If652c133093a21e530f4e9eab09097976f57fb12
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When I had rewritten the code for ixgbe_clear_vf_vlans() it looks like I
had transitioned back and forth between using word as an offset and using
word as a register offset. As a result I honestly don't see how the code
was working before other than the fact that resetting the VLANs on the VF
like didn't do much to clear them.
Another issue found is that the mask was using a divide instead of a
modulus. As a result the mask bit was incorrectly being set to either bit
0 or 1 based on the value of the VF being tested. As a result the wrong
VFs were having their VLANs cleared if they were enabled.
I have updated the code so that word represents the offset in the array.
This way we can use the modulus and xor operations and they will make sense
instead of being performed on a 4 byte aligned value.
I replaced the statement "(word % 2) ^ 1" with "~word % 2" in order to
reduce the line length as the line exceeded 80 characters with the register
name inserted. The two should be equivalent so the change should be safe.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x revision check needs to check a value, not just a bit.
Use a mask and check the value. Also remove the redundant check
inside the ixgbe_enter_lplu_t_x550em, because it can only be called
when both the mac type and revision check pass.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 allows for up to 64 RSS queues, but the driver can have max
of 63 (-1 MSIX vector for link).
On systems with >= 64 CPUs the driver will set the redirection table
for all 64 queues which will result in packets being dropped.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the
backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add missing QSFP PHY types to allow for more accurate reporting of
port settings.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some X550 devices can connect at 2.5Gbps during fail-over, but only
with certain link partners. Also setting the advertised speed will
not work so we do not report it as supported to avoid confusion.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch guarantees that the VFs do not have access to VLANs that they
were not supposed to. What this patch does is add code so that we delete
the previous port VLAN after adding a new one, and if we reset the VF we
clear all of the filters associated with it.
Previously the code was leaving all previous VLANs mapped to the VF and
they didn't get deleted unless the VF specifically requested it or if the
PF itself was reset.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes certain that we clear the pool mappings added when we
configure default MAC addresses for the interface. Without this we run the
risk of leaking an address into pool 0 which really belongs to VF 0 when
SR-IOV is enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry. What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for VLAN promiscuous with SR-IOV enabled.
The code prior to this patch was only adding the PF to VLANs that the VF
had added. As such enabling promiscuous mode would actually not add any
additional VLAN filters so visibility was limited. This lead to a number
of issues as the bridge and OVS would expect us to accept all VLAN tagged
packets when promiscuous mode was enabled, and instead we would filter out
most if not all depending on the configuration of the PF.
With this patch what we do is set all the bits in the VFTA and all of the
VLVF bits associated with the pool belonging to the PF. By doing this the
PF is guaranteed to receive all VLAN tagged traffic associated with the RAR
filters assigned to the PF. In addition we will clean up those same bits
in the event of promiscuous mode being disabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to reduce the complexity of the search function used
for finding a VLVF entry associated with a given VLAN ID. The previous
code was searching from bottom to top. I reordered it to search from top
to bottom. In addition I pulled an AND statement out of the loop and
instead replaced it with an OR statement outside the loop. This should
help to reduce the overall size and complexity of the function.
There was also some formatting I cleaned up in regards to whitespace and
such.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN. The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses several issues within the VLVF and VLVFB
configuration
First was the fact that code was overly complicated with multiple
conditional paths depending on if we adding or removing and which bit we
were going to add or remove. Instead of messing with all that I have
simplified it by using (vid / 32) and (1 - vid / 32) to identify our
register and the other vlvfb register.
Second was the fact that we were likely leaking a few packets into the PF
in cases where we were deleting an entry and the VFTA filter for that entry
as the ordering was such that we deleted the pool and then the VLAN filter
instead of the other way around. I have updated that by adding a check for
no bits being set and if that occurs we clear things up in the proper
order.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to clear the way for upcoming work I thought it best to drop the
level of indent in the ixgbe_set_vfta_generic function. Most of the code
is held in the virtualization specific section. So the easiest approach is
to just add a jump label and jump past the bulk of the code if it is not
enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the logic for setting the VFTA register by removing
the number of conditional checks needed. Instead we just use some boolean
logic to generate vfta_delta, and if that is set then we xor the vfta by
that value and write it back.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code for checking the PF bit in ixgbe_set_vf_vlan_msg was using the
wrong offset and as a result it was pulling the VLAN off of the PF even if
there were VFs numbered greater than 40 that still had the VLAN enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a check to make certain mac_table was actually allocated and is not
NULL. If it is NULL return -ENOMEM and allow the probe routine to fail
rather then causing a NULL pointer dereference further down the line.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000
Result:
MPSAR[0] 00000081
MPSAR[254] 00000001
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of inhibiting PHY power control when manageability is
present, only inhibit turning PHY power off when manageability
is present. Consequently, PHY power will always be turned on when
requested. Without this patch, some systems with X540 or X550
devices in some conditions will never get link.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the datasheets, the driver should wait for the master
disable bit to read as being set before checking the status
register for master disable.
Reported-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver was violating the specification in the datasheet
by not waiting 1ms before checking for the reset bit clearing. This
is called out for devices supported by ixgbe, so implement the
required delay.
Reported-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.
Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was. So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead. This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance. This change updates the code in general to
clean it up so it becomes clear what each step is doing. From what I can
tell there a couple of bugs cleaned up in this code.
First is the fact that the MAC addresses were being double counted for the
PF. As a result once entries up to 63 had been used you could no longer
add additional filters.
A simple test case for this:
for i in `seq 0 96`
do
ip link add link ens8 name mv$i type macvlan
ip link set dev mv$i up
done
Test script:
ethregs -s 0:8.0 | grep -e "RAH" | grep 8000....$
When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The newer copper PHY implementation used with newer X550EM_x
devices uses a different thermal alarm type than the earlier
one. Make changes to support both types.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes KR PHY reset from ixgbe_init_phy_ops_x550em,
since this function is meant to initialize function pointers for
the detected PHY type. Internal PHY reset was moved to
ixgbe_setup_internal_phy_t_x550em which will now detect which
mode the internal PHY operates in and set it up as required.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Testing has now shown that the diagnostic code used with the CS4227
is no longer needed, so remove it.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_intr and ixgbe/ixgbevf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
KR auto-neg mode is what we will be using going forward. The SW
interface for this mode is different that what was used for iXFI.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit dfaf891dd3 ("ixgbe: Refactor the RSS configuration code")
introduced a few kernel-doc errors:
1) The function name is missing;
2) The format is wrong;
3) The short description is redundant.
Fix all the above for the correct execution of the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete a redundant include of net/vxlan.h.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)
napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()
This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.
Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.
Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation of the number of multicast address for VF is not enough
for the large scale server with SR-IOV feature. IPv6 requires the multicast
MAC address for each IP address to handle the Neighbor Solicitation
message. We couldn't assign over 30 IPv6 addresses to a single VF.
This patch introduces the new mailbox API, IXGBE_VF_UPDATE_XCAST_MODE,
to update multicast mode of VF. This adds 3 modes;
- NONE only L2 exact match addresses or Flow Director enabled
- MULTI BAM and ROMPE set
- ALLMULTI BAM, ROMPE and MPE set
If a guest VF user wants over 30 MAC multicast addresses, set IFF_ALLMULTI
to request PF to update xcast mode to enable VF multicast promiscuous mode.
On the other hand, enabling VF multicast promiscuous mode may affect
security and performance in the network of the NIC. Only trusted VF can
enable multicast promiscuous mode. The behavior of untrusted VF is the
same as previous version.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implements the new netdev op to trust VF in ixgbe.
The administrator can turn on and off VF trusted by ip command which
supports trust message.
# ip link set dev eth0 vf 1 trust on
or
# ip link set dev eth0 vf 1 trust off
Send a ping to reset VF on changing the status of trusting.
VF driver will reconfigure its features on reset.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only call the internal_setup_link method when it is provided. This
check is required for newer version parts.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the reset never completes, it is necessary to retake the
semaphore before returning, because the caller will release
the semaphore.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch disables LRO by default in favor of GRO.
LRO is incompatible with forwarding and is disabled when forwarding
is turned on which makes the default offloads of the driver
inconsistent. LRO can still be enabled via ethtool.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that flow control packets initiated by the VF are
dropped and reported as spoofed.
Flow control packets can be used to limit the throughput or as DOS
attack when generated from a VF. Flow control is not supported per VF
hence any pause frames generated from a VF are considered malicious.
Also cleaned up indentation and some redundant comments.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the addition of X550em_x SFP+ support, the driver is now
functionally equivalent to what will be the 4.2.1 driver when
released, so change the version to match.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 thermal interrupt (IXGBE_EIMS_TS) is not an SDP, so it
doesn't need to be enabled in ixgbe_setup_gpie(). In fact the
value is simply not for the GPIE register at all.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82599 and X540 datasheets require that FCRTH be "set" for Tx
switching (VM-to-VM loopback) but it did not previously specify what
the value should be set to. It has now been determined that
the correct value is RXPBSIZE - (24*1024).
This setting is also required for later devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A logic error here results in the adapter_stopped flag only being
cleared when ixgbe_setup_fc returns an error. Correct the logic.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change does two things. First, it makes it so that we always
set the relaxed ordering bits related to the DCA registers even if
DCA is not enabled. Second, it moves the configuration out of the
ixgbe_down function and into the ixgbe_configure function before
enabling the Rx and Tx rings. This ensures that DCA is configured
correctly before starting to process packets.
Thanks to Alex Duyck for this fix.
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new device ID for X550EM device with SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch skips the PCI transactions pending check in
ixgbe_disable_pcie_master. This is done to addresses a known HW
issue where the PCI transactions pending bit sticks high when there
are pending transactions. HW engineering instructed to workaround
this issue by wait and then continue with our reset flow.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which
enables padding of small packets.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting the X550* RDRXCTL register should fall through into X540
and 82599, not 82598.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The timeout path is supposed to release the semaphore, so do that.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take control of an I2C mux that selects which SFP is attached to
the I2C bus. The control of the mux is captured in the taking and
releasing of the related semaphore. Because only port 1 can control
the mux, port 1 always leaves the mux set to select port 0.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the frequency of polling for SFP modules. Because the
service task sometimes runs at high rates, we can poll for
SFPs too often. When an SFP is not present, the I2C timeouts
that result are very costly. So, prevent SFP polling from
being done more than once every two seconds. To reduce latency,
the poll time is cleared in a couple of cases to permit the
next service task execution to poll the SFP module.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since SFP+ can be used with some X550 devices, permit them to be
detected.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Configures the CS4227 correctly for both 1G and 10G operation,
by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It
needs to be in this function because we need both the module
type and the speed, and this is the only function in the init
flow that knows the speed. In contrast,
ixgbe_setup_sfp_modules_X550em() does not know the speed, so we
can't do anything useful here. This is a fundamental difference
from the previous flow, and is due to the way the CS4227 is
implemented.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds X550EM_x SFP+ dual-speed support. 82599 fiber link
code was moved from ixgbe_82599.c to ixgbe_common.c for use by
X550EM. SFP MAC link code is added to x550EM.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the number of retries during PHY detection. This reduces
pauses when no SFP is present. Once an SFP is detected, the normal
retry count will be used.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the destination location for I2C data initially so that
the received data will not be affected by previous attempts.
This could have returned wrong data in certain retry sequences.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the bit banging mode in the hardware when performing bit banging
I2C operations on X550. Also control the output enable on both the
clock and data lines.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The lan_id is being set after a previous I2C eeprom access which
makes no sense because it needs to be set before any access. Move
the setting to before the access.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most I2C accesses take and release semaphores for each access. Now
there is a reason to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provide I2C combined operations on X550EM, not X550 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the SFP insertion interrupt on X550EM devices with
SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an SFP not present error is returned by the reset_hw method,
accept it and go on, since an SFP can still be inserted. Previously
it was only accepted for 82598 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 has HW support for SCTP flow director filters SCTP mask. This
patch adds it like we do for UDP and TCP.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is part of the future enablement of X550 SFP+ support. This
HW uses different SDP so the interrupts need to be set up accordingly.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the lowest limit for adaptive interrupt interrupt
moderation to roughly 12K interrupts per second.
The way I came about reaching 12K as the desired interrupt rate is by
testing with UDP flows. Specifically I had a simple test that ran a
netperf UDP_STREAM test at varying sizes. What I found was as the packet
sizes increased the performance fell steadily behind until we were only
able to receive at ~4Gb/s with a message size of 65507. A bit of digging
found that we were dropping packets for the socket in the network stack,
and looking at things further what I found was I could solve it by increasing
the interrupt rate, or increasing the rmem_default/rmem_max. What I found was
that when the interrupt coalescing resulted in more data being processed
per interrupt than could be stored in the socket buffer we started losing
packets and the performance dropped. So I reached 12K based on the
following math.
rmem_default = 212992
skb->truesize = 2994
212992 / 2994 = 71.14 packets to fill the buffer
packet rate at 1514 packet size is 812744pps
71.14 / 812744 = 87.9us to fill socket buffer
From there it was just a matter of choosing the interrupt rate and
providing a bit of wiggle room which is why I decided to go with 12K
interrupts per second as that uses a value of 84us.
The data below is based on VM to VM over a direct assigned ixgbe interface.
The test run was:
netperf -H <ip> -t UDP_STREAM"
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
Before:
212992 65507 60.00 1100662 0 9613.4 10.89 0.557
212992 60.00 473474 4135.4 11.27 0.576
After:
212992 65507 60.00 1100413 0 9611.2 10.73 0.549
212992 60.00 974132 8508.3 11.69 0.598
Using bare metal the data is similar but not as dramatic as the throughput
increases from about 8.5Gb/s to 9.5Gb/s.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
This also includes a modified check generating the EICR mask to be
more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve warnings resulting from redundant initialization of the
get_bus_info field in the mac_ops_X550* structures.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When unbinding an SR-IOV device with VFs configured from ixgbe, the
driver behaves in one of two ways. If max_vfs was specified, the
SR-IOV state is disabled, removing the VFs. The occurs regardless of
whether the VF count was later modified through sysfs. If however
max_vfs is zero, such as by not specifying the module parameter, the
VFs persist after the PF is unbound from ixgbe. If the PF is then
bound to vfio-pci to be assigned to a VM, the PF is non-functional.
>From the comment, commit da36b64736 ("ixgbe: Implement PCI SR-IOV
sysfs callback operation") clearly intended this alternate behavior,
but probably didn't realize the PF doesn't work in this mode.
This bimodal behavior is confusing to users and results in a state
where the PF is broken for other uses unless the user sets
sriov_numvfs to zero prior to unbinding the device. Remove this
behavior so that VFs are removed and the PF is functional for other
uses after unbind, regardless of the way VFs are enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we can do 2.5G link speed, we need to be able to report it.
Also change the nested triadic involved in creating the log message
to instead use a simpler switch statement to set a string pointer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue where users were not able to dynamically
set number of queues for 82598 via ethtool -L
Reported-by: Tal Abudi <talabudi@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allows to change the rxfh indirection table and/or key using
ethtool interface.
Signed-off-by: Tom Barbette <tom.barbette@ulg.ac.be>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid a needless PHY access on copper phys to save the 10ms wait
time for each PHY access. A helper function is introduced to
actually do the register access and process the contents.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already cache this FW/SW semaphore mask so might as well use it
for consistency.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the redundant lan_id in the phy struct and uses
the bus version. Both variables exist and intend to represent the
STATUS register LAN_ID field. However, phy.lan_id is not bit shifted
so the phy.lan_id = 0x0 for LAN Id 0 and phy.lan_id = 0x4 for LAN Id 1.
Where bus.lan_id is bit shifted so bus.lan_id = 0x0 for LAN Id 0 and
bus.lan_id = 0x1 for LAN Id 1. There seems no need for the additional
lan_id variable and this should make the code less confusing.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use kzalloc rather than kcalloc(1..
The semantic patch that makes this change is as follows:
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
and removing checkpatch below CHECK:
CHECK: Prefer kzalloc(sizeof(*fwd_adapter)...) over
kzalloc(sizeof(struct ixgbe_fwd_adapter)...)
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe never has as very doubtfully ever will support either
PCI or PCI-X devices. So remove the unused types from the
ixgbe_bus_type. Thanks to Alex Duyck for suggesting this.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this patch we add support for a new bus type ixgbe_bus_type_internal.
X550em devices use IOSF and not PCIe bus so this new type is to accommodate
them.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added ixgbe_get_bus_info_X550em to X550 code. ixgbe_get_bus_info_X550em
sets bus.width to ixgbe_bus_width_unknown and bus.speed to
ixgbe_bus_speed_unknown, because IOSF does not report a PCIe bus
width or speed.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is closing or suspending, call ixgbe_enter_lplu to
enter low power link up state on devices that support it. When this
is done, prevent the phy from being reset in the ixgbe_down path
so that link is present when calling ixgbe_enter_lplu.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for VXLAN RX offloads for the X55x devices that support
them.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By using GSO for UDP-encapsulated packets, all ixgbe devices can
be directed to generate checksums for the inner headers because
the outer UDP checksum can be zero. So point the machinery at the
inner headers and have the hardware generate the checksum.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wait up to about 100 us for FDIRCMD writes to complete and return
failure indications.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are various reasons why this method may or may not need to be
defined and some of these we don't know until runtime. So we will
set the value in get_invariants.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a support function that will indicate for the
existence of management FW.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit c48a11c7ad ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simplify port-specific macros by eliminating explicit comparison
with 0. More importantly, enclose formal parameter in parens to
eliminate the risk of an operator precedence surprise.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For two reasons I want to disable this:
1. Not any part actually check the report status(Alexander Duyck)
2. To report hash value of a packet to stack,
RSS -> 32bits hash value
Perfect match fdir filter -> 13bits hash value
Hashed-based fdir filter -> 31bits hash value
fdir filter might hash on masked tuples for IP address,
so it's still not desirable for usage.
So for now, just stick to RSS 32bits hash value.
Signed-off-by: Fan Du <fan.du@intel.com>
Suggested-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS could be leveraged by taking account L4 src/dst ports
as ingredients, thus ingress skb Rx hash type should honor
such the real configuration.
Signed-off-by: Fan Du <fan.du@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a bug in ixgbe_setup_ixfi_x550em where we were
reading and modifying IXGBE_KRM_LINK_CTRL_1 but forgot to write the
results back.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Even though X550 may later clear this value for certain devices
set it initially to support copper.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to call the set_lan_id before accessing I2C and this wasn't
being done so this patch corrects that. Likewise we do the same for
QSFP just to be consistent.
In the X550 case this is even more important as with out it the mux
is not controlled properly.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds ixgbe_check_link_t_X550em for checking copper PHY
link. We check that both the MAC and external PHY have link. This
is to avoid a false link up between the internal and external PHY
when the external PHY doesn't have link.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for another 10baseT X550 device.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A subset of the X550 function pointers didn't have default methods. This
didn't cause any issue with previous X550 devices as they were all
redefined. However future devices will need these default values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reviewing the X550 copper init flow with the Si team resulted in a
new simplified flow. We no longer wait for the PHY FW initialization
complete bit to be set as this bit is only set once by the PHY at power
on and then cleared on the first read. So only the first instance of
running SW (or possibly MAC FW) needs to initialize the PHY.
The PHY initialization has been simplified and now only requires that
the PHY FW be un-stalled
low-power mode or enabled the transceiver
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This check was missed in when this new MAC type was added. Since
these counts can be incremented for X550 we need to clear them.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
We do this by updating the ixgbe_is_sfp to be aware of the
new X550 devices. This also includes a modified check generating
the EICR mask to be more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for receiving interrupts from a external copper
PHY for the X550 part. This includes enabling, detection as well as
re-enablement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The over heat message is displayed for multiple reasons but the text is
cut-n-pasted for each of these cases. This patch pulls the text from the
same location. I noticed this as I am about to add another case.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a PHY reset function ixgbe_reset_phy_t_X550em. Which
allows devices that have LASI support in enable their interrupt.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds x550 external PHY interrupt and forced 1G/10G support.
This included enabling and handling LSC and thermal sensor interrupt.
ixgbe_handle_lasi() has been added for handling the interrupts received
over SDP0 from the external 10baseT PHY. ixgbe_enable_lasi_ext_t_x550em
and ixgbe_get_lasi_ext_t_x550em have been added to X550em to enable
mask and check interrupt flags for the external PHY.
Forced 1G/10G link speed is handled via ixgbe_mac_link_t_X550em.
ixgbe_seupt_mac_link_t_X550em sets up the internal PHY and external PHY
to either iXFI (10G) or KX (1G) based on the user selected auto
advertised link speed setting. Then sets up the external PHY auto
advertised link speed.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset. Combine
all this functionality in to a support function.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This new method will control the PHY power state. You pass in the
state you wish to change to (ether on or off). For cases where this
method is not used the current PHY power state behavior is maintained.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a define for the new PHY identification as well as it's mapping
to the correct PHY type. Also allow ethtool to identify this type
as well.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These Device ID could support both WoL and autoneg flow control. In
the case of WoL this is indicated by the eeprom. This patch enables
these devices this support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of the register addresses and format where unfortunately changed
between MAC types. To get around this we add a const u32 *mvals pointer
to the ixgbe_hw struct to point to an array of mac-type-dependent
values. These can include register offsets, masks, whatever can be in
a u32. When the ixgbe_hw struct is initialized, a pointer to the
appropriate array must be set.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flow director is exported to user space using the ethtool ntuple
support. However, currently it only supports steering traffic to a
subset of the queues in use by the hardware. This change allows
flow director to specify queues that have been assigned to virtual
functions by partitioning the ring_cookie into a 8bit VF specifier
followed by 32bit queue index. At the moment we don't have any
ethernet drivers with more than 2^32 queues on a single function
as best I can tell and nor do I expect this to happen anytime
soon. This way the ring_cookie's normal use for specifying a queue
on a specific PCI function continues to work as expected.
CC: Alex Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because error codes are negative, it only makes sense to
consistently use signed types when handling them. Also remove
some explicit comparisons with 0 on these variables.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The global semaphore bits should be released in the reverse of the
order that they were taken, so correct that.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IOSF is the Intel On-chip System Fabric used in SOCs. IOSF SB is
the IOSF SideBand message interface. This patch serializes IOSF SB
access using both phy bits in the SWFW_SEMAPHORE register. It also
adds a helper function to wait for IOSF SB accesses to complete.
Use the new function to perform this wait before each access, as
specified in the datasheet, in addition to using it to wait for
IOSF SB read/write completion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 82599 and x540 VFs and PF share the same RSS Key. Therefore we will
return the same RSS key for all VFs.
Support for other devices will be added later.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add this new command for 82599 and x540 devices only. Support for other
devices will be added later.
82599 and x540 VFs and PF share the same RSS redirection table (RETA).
Therefore we just return it for all VFs.
For 82599 and x540 RETA table is an array of 32 registers (128 bytes) and
the maximum number of registers that may be delivered in a single VF-PF
channel command is 15. On the other hand VFs of these devices can be
configured to have up to 4 RSS queues. Therefore we will "compress" the
RETA by transferring only 2 bits per entry and thereby it will take only 8
registers (DWORDS) to transfer the whole VF RETA.
Thus this patch does the following:
- Adds a new API version (to specify a new commands set).
- Adds the IXGBE_VF_GET_RETA command to the VF-PF commands set.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implements the new netdev op to allow user to enable/disable the ability
of a specific VF to query its RSS Indirection Table and an RSS Hash Key.
This patch limits the new feature support to 82599 and x540 devices only.
Support for other devices will be added later.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added get_rxfh_indir_size, get_rxfh_key_size and get_rxfh ethtool_ops
callbacks implementations.
This enables the ethtool's "-x" and "--show-rxfh[-indir]" options.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a preparation for enablement of ethtool RSS indirection
table and hash key querying. We don't want to read registers every time
the RSS info is queried. Therefore we will store its current content in the
arrays in the adapter struct and will read it from there (instead of from
registers) when requested.
Will change the code that writes the indirection table and hash key into
the HW registers to take its content from these arrays. This will also
simplify the indirection table updating ethtool callback implementation
in the future.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver hasn't used call_rcu to free the rings for some time now.
Since that is the case the call to rcu_barrier can be dropped since calls
to kfree_rcu don't require it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the HW_VLAN_CTAG_FILTER bit is not falsely
advertised as being a feature that can be toggled on ixgbe parts. The
driver was setting the bit in features and letting it be inherited by
hw_features, however the driver was actually ignoring the value of the bit
and just assuming it was always set. As a result VLAN filtering was always
enabled which is a requirement for SR-IOV, VMDq, DCB, FCoE, and possibly
other features within the adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds x550 specific FCoE offloads for DDP context programming and
increased DDP exchanges.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch will enable X550 Source Address Prunning for VEPA
bridge mode. This requires that we also have replication enabled
as well, while in this mode.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch gathers together all the logic needed to configure bridge
modes. Currently that it is rather simple but this is really laying
the ground work for future X550 feature enhancement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently storing our BRIDGE_MODE as a bit in our adapter flags.
This patch will store the actual mode instead which minimizes obfuscation
and makes following patches for X550 simpler.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bool constants as the return values instead of 1 and 0.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's clock is implemented using a timecounter, and so with
this patch the driver is ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some dead code from the cleanup path for ixgbe.
Setting and clearing the flag doesn't do anything since all we are
doing is setting the flag, scheduling NAPI, clearing the flag and
then letting netpoll do the polling cleanup. As such it doesn't
make much sense to have it there.
This patch also removes one minor white-space error.
CC: <kernel-team@fb.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that relaxed ordering is not disabled when
on SPARC, where it helps with performance.
CC: <kernel-team@fb.com>
CC: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Correcting a mistake when I initial created this function. I should
have made this static since it is only referenced where the function
pointer is assigned.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Missed this when I created commit 6a14ee0cfb ("ixgbe: Add X550 support
function pointers"). Use a the __be* type to be consistent with how the
value is assigned.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the X550 mac type we have to do additional steps around
enabling/disabling Rx. This patch will add a layer of indirection
around these support functions to enable this.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the ethertype Anti-Spoofing feature for affected
devices. It is configured such that LLDP packets sent by a VF will
be dropped.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support VXLAN receive checksum offload in X550 hardware.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We always identify the PHY in our reset_hw path anyway so there is
no need to do it in get_invariants(). The reason I even noticed this
is that for new hardware (X550em) we don't assign some methods until
later in probe and calling phy.ops.read_reg could lead to a panic.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
My original patch 6a14ee0cfb "ixgbe: Add X550 support function pointers"
accidental set a default value for this structure member twice.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes couple of issues introduced by
commit 2b509c0cd2 ("ixgbe: cleanup ixgbe_ndo_set_vf_vlan")
- fix setting of the VLAN inside ixgbe_enable_port_vlan()
- disable the "hide VLAN" bit in PFQDE when port VLAN is disabled
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_set_sriov_queues() has the logic to allow multiple queues, this patch
just removes the limitation.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up prototypes that should have been defined
as static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbe_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.
Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that dma_rmb is used when reading the Rx
descriptor. The advantage of dma_rmb is that it allows for a much
lower cost barrier on x86, powerpc, arm, and arm64 architectures than a
traditional memory barrier when dealing with reads that only have to
synchronize to coherent memory.
In addition I have updated the code so that it just checks to see if any
bits have been set instead of just the DD bit since the DD bit will always
be set as a part of a descriptor write-back so we just need to check for a
non-zero value being present at that memory location rather than just
checking for any specific bit. This allows the code itself to appear much
cleaner and allows the compiler more room to optimize.
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces calls to netdev_alloc_skb_ip_align with
napi_alloc_skb. The advantage of napi_alloc_skb is currently the fact that
the page allocation doesn't make use of any irq disable calls.
There are few spots where I couldn't replace the calls as the buffer
allocation routine is called as a part of init which is outside of the
softirq context.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.
Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has logic to free up used data in case any of the checks in
ixgbe_probe() fail, however there is a similar set of cleanups that can
occur on driver unload in ixgbe_remove() which can cause the rmmod command
to crash.
This patch aims to fix the logic by moving pci_set_drvdata() after all error
checks and then adds a check in ixgbe_remove() to skip it altogether if
adapter comes up empty.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we now support X550 mac's bump the version number to reflect this.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the function pointer structure to include the new
X550 class MAC types. This creates a new file ixgbe_x550.c that contains
all of the new methods. Because of similarities to the X540 part in
some cases we just use it's methods where they can be used without any
modification. These exported functions are now defined in the new
ixgbe_x540.h file.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the shared code checksum calculation function only
returns a u16 and cannot return an error code. Unfortunately
a variety of errors can happen that completely prevent the
calculation of a checksum. So, change the function return value
from a u16 to an s32 and return a negative value on error, or the
positive checksum value when there is no error.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some X550 procedures will be using CS4227 PHY and need to
perform combined read and write operations. This patch
adds those methods.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550 hardware will use more bits in the mask, so change
the prototypes to match. This larger mask will require changes
in callers which use the higher bits. Likewise since X550 will
use different semaphore mask values and will use the lan_id
value. So save these values in the ixgbe_phy_info struct.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since on X550 we use host interface commands to read,write and erase
some commands require more time to complete. So this adds a timeout
parameter to ixgbe_host_interface_command as wells as a return_data
parameter allowing us to return with any data.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new X550 family of MAC's will have a larger RSS hash (16 -> 64).
It will also support individual VF to have their own independent RSS
hash key. This patch will enable this functionality
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accessing the CIAA/D register can block access to the PCI config space.
This patch removes the read/write operations to the CIAA/D registers
and makes use of standard kernel functions for accessing the PCI config
space.
In addition it moves ixgbevf_check_for_bad_vf() into the watchdog subtask
which reduces the frequency of the checks.
CC: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Attempt to look up the MAC address in Open Firmware on systems that
support it. On SPARC resort to using the IDPROM if no OF address is
found.
Signed-off-by: Martin K Petersen <martin.petersen@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the tail writes for the ixgbe descriptor queues. The
current implementation had me confused as I wasn't sure if it was still
making use of the surprise remove logic or not.
It also adds the mmiowb which is needed on ia64, mips, and a couple other
architectures in order to synchronize the MMIO writes with the Tx queue
_xmit_lock spinlock.
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.
It also cleans up how we clear the descriptor status bits. Previously they
were zeroed as a part of clearing the hdr_addr. However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems. Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared. As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To allow brport device to return current brport flags set on port. Add
returned flags to nested IFLA_PROTINFO netlink msg built in dflt getlink.
With this change, netlink msg returned for bridge_getlink contains the port's
offloaded flag settings (the port's SELF settings).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_bridge_setlink() is currently only called on the slave if
IFLA_AF_SPEC is set but this is a very fragile assumption and may
change in the future.
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: a77dcb8c8 ("be2net: set and query VEB/VEPA mode of the PF interface")
Fixes: 815cccbf1 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on a different issue, I noticed an annoying use
after free bug on my machine when unloading the ixgbe driver:
[ 8642.318797] ixgbe 0000:02:00.1: removed PHC on p2p2
[ 8642.742716] ixgbe 0000:02:00.1: complete
[ 8642.743784] BUG: unable to handle kernel paging request at ffff8807d3740a90
[ 8642.744828] IP: [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[ 8642.745886] PGD 20c6067 PUD 81c1f6067 PMD 81c15a067 PTE 80000007d3740060
[ 8642.746956] Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
[ 8642.748039] Modules linked in: [...]
[ 8642.752929] CPU: 1 PID: 1225 Comm: rmmod Not tainted 3.18.0-rc2+ #49
[ 8642.754203] Hardware name: Supermicro X10SLM-F/X10SLM-F, BIOS 1.1b 11/01/2013
[ 8642.755505] task: ffff8807e34d3fe0 ti: ffff8807b7204000 task.ti: ffff8807b7204000
[ 8642.756831] RIP: 0010:[<ffffffffa01c77dc>] [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[...]
[ 8642.774335] Stack:
[ 8642.775805] ffff8807ee824098 ffff8807ee824098 ffffffffa01f3000 ffff8807ee824000
[ 8642.777326] ffff8807b7207e18 ffffffff8137720f ffff8807ee824098 ffff8807ee824098
[ 8642.778848] ffffffffa01f3068 ffff8807ee8240f8 ffff8807b7207e38 ffffffff8144180f
[ 8642.780365] Call Trace:
[ 8642.781869] [<ffffffff8137720f>] pci_device_remove+0x3f/0xc0
[ 8642.783395] [<ffffffff8144180f>] __device_release_driver+0x7f/0xf0
[ 8642.784876] [<ffffffff814421f8>] driver_detach+0xb8/0xc0
[ 8642.786352] [<ffffffff814414a9>] bus_remove_driver+0x59/0xe0
[ 8642.787783] [<ffffffff814429d0>] driver_unregister+0x30/0x70
[ 8642.789202] [<ffffffff81375c65>] pci_unregister_driver+0x25/0xa0
[ 8642.790657] [<ffffffffa01eb38e>] ixgbe_exit_module+0x1c/0xc8e [ixgbe]
[ 8642.792064] [<ffffffff810f93a2>] SyS_delete_module+0x132/0x1c0
[ 8642.793450] [<ffffffff81012c61>] ? do_notify_resume+0x61/0xa0
[ 8642.794837] [<ffffffff816d2029>] system_call_fastpath+0x12/0x17
The issue is that test_and_set_bit() done on adapter->state is being
performed *after* the netdevice has been freed via free_netdev().
When netdev is being allocated on initialization time, it allocates
a private area, here struct ixgbe_adapter, that resides after the
net_device structure. In ixgbe_probe(), the device init routine,
we set up the adapter after alloc_etherdev_mq() on the private area
and add a reference for the pci_dev as well via pci_set_drvdata().
Both in the error path of ixgbe_probe(), but also on module unload
when ixgbe_remove() is being called, commit 41c62843eb ("ixgbe:
Fix rcu warnings induced by LER") accesses adapter after free_netdev().
The patch stores the result in a bool and thus fixes above oops on my
side.
Fixes: 41c62843eb ("ixgbe: Fix rcu warnings induced by LER")
Cc: stable <stable@vger.kernel.org>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IXGBE adapter seems to require that VLAN filtering be enabled if
VMDQ or SRIOV are enabled. When those functions are disabled,
VLAN filtering may be disabled in promiscuous mode.
Prior to commit a9b8943ee1 ("ixgbe: remove vlan_filter_disable
and enable functions")
The logic was correct. However, after the commit the logic
got reversed and VLAN filtered in now turned on when VMDQ/SRIOV
is disabled.
This patch changes the condition to enable hw vlan filtered
when VMDQ or SRIOV is enabled.
Fixes: a9b8943ee1 ("ixgbe: remove vlan_filter_disable and enable functions")
Cc: stable <stable@vger.kernel.org>
CC: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel drivers were pretty much just using the plain vanilla GFP flags
in their calls to __skb_alloc_page so this change makes it so that they use
dev_alloc_page which just uses GFP_ATOMIC for the gfp_flags value.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Status variable is never initialized, can carry an arbitrary value
on the stack and thus may let the function fail.
Fixes: e90dd26456 ("ixgbe: Make return values more direct")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split off the setting of the RSS key into its own function. This
will help when we add support for X550 which can have different
RSS keys per pool.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch will add in the new MAC defines and fit it into the switch
cases throughout the driver. New functionality and enablement support will
be added in following patches.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move setting of drop enable to support function. This not only makes the
code more readable but is also prep for following patches that add
additional MAC support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up functionality in ixgbe_ndo_set_vf_vlan that will simplify later
patches.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On topologies including few levels of PCIe switching X540 can run into an
unexpected completion error. We get around this by waiting after enabling
loopback a sufficient amount of time until Tx Data Fetch is sent. We then
poll the pending transaction bit to ensure we received the completion. Only
then do we go on to clear the buffers.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following commands:
modprobe ixgbe
ifconfig ethX up
ethtool -s ethX advertise 0x020
can lead to "setup link failed with code -14" error due to the setup_link
call racing with the SFP detection routine in the watchdog.
This patch resolves this issue by protecting the setup_link call with check
for __IXGBE_IN_SFP_INIT.
Reported-by: Scott Harrison <scoharr2@cisco.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Martin Zhang <martinbj2008@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for vfinfo is not sufficient because it does not protect
against specifying vf that is outside of sriov_num_vfs range.
All of the ndo functions have a check for it except for
ixgbevf_ndo_set_spoofcheck().
The following patch is all we need to protect against this panic:
ip link set p96p1 vf 0 spoofchk off
BUG: unable to handle kernel NULL pointer dereference at 0000000000000052
IP: [<ffffffffa044a1c1>]
ixgbe_ndo_set_vf_spoofchk+0x51/0x150 [ixgbe]
Reported-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is typo in ixgbe.h, two marcro definition of IXGBE_MAX_L2A_QUEUES to 4,
delete one, clear the compiler warning.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch consolidates the logic behind dynamically setting TXDCTL.WTHRESH
depending on interrupt throttle rate (ITR) setting regardless of BQL.
Previously TXDCTL.WTHRESH was dynamically being set only with BQL being
enabled, but we have to set it regardless of BQL when ITR is low to avoid
Tx stalls/hangs.
CC: John Greene <jogreene@redhat.com>
Reported by: Masayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes couple of wait loops on autoneg that are not needed.
During validation we noticed that the loops always time out, so there
should be no user impact.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert the normal packet completion path to dev_consume_skb_any() so
packet drop profiling via dropwatch or perf top -G -e skb_kfree_skb
is not cluttered with false hits.
Compile tested only. There is a dev_kfree_skb_any() in the routine
ixgbe_ptp_tx_hwtstamp() in ixgbe_ptp.c that looks like a conversion
candidate but I wasn't familiar enough with the code to pull the
trigger.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
They were not used, and we don't need them, so we shouldn't bother with
keeping values in the flags field that could be misleading.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we can't get MSI-X vectors, we disable a few features which require
MSI-X vectors. Print warnings just like we do when disabling DCB.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Again, we should not be directly using netif_printk, as we have our own
error print routines that we generate. In addition, instead of using an
early return we can just use the else block of this one line if
statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In this case, disabling DCB is not an error. We can still function, but
we just have to let the user know. In addition, since we call this
during probe before allocating our netdevice structure, we should use
e_dev_warn instead of e_warn.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our calculated v_budget doesn't matter except if we allocate MSI-X
vectors. We shouldn't need to calculate this outside of the function, so
don't. Instead, only calculate it once we attempt to acquire MSI-X
vectors. This helps collocate all of the MSI-X vector code together.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already have to kfree this value if we fail, and this is only part of
MSI-X mode, so we should simply allocate the value where we need it.
This is cleaner, and makes it a lot more obvious why we are freeing it
inside of ixgbe_acquire_msix_vectors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to how ixgbevf handles acquiring MSI-X vectors, we can return an
error code instead of relying on the flag being set. This makes it more
clear that we have failed to setup MSI-X mode, and also will make it
easier to consolidate MSI-X related code all into the single function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The netif_printk relies on our netdevice structure to be registered
already. We may call ixgbe_acquire_msix_vectors prior to registering our
netdevice, so we should not use the netdevice specific printk.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a hardware Tx timestamp is requested, an uninitialized
workqueue entry may be scheduled, especially on an 82598 adapter.
Add a check for a PTP clock to avoid that. Also only apply the
unlikely to the first term of the conditional. That will make the
rest of the checks be in the cold path.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because bd_number is not useful anymore, so remove it from adapter struct, or
if keep it, we have to fix the boards driven counter bug in ixgbe_remove() and
ixgbe_probe() only for trivial debug purpose -- other output is enough.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change addresses several issues in the current ixgbe implementation of
busy poll sockets.
First was the fact that it was possible for frames to be delivered out of
order if they were held in GRO. This is addressed by flushing the GRO buffers
before releasing the q_vector back to the idle state.
The other issue was the fact that we were having to take a spinlock on
changing the state to and from idle. To resolve this I have replaced the
state value with an atomic and use atomic_cmpxchg to change the value from
idle, and a simple atomic set to restore it back to idle after we have
acquired it. This allows us to only use a locked operation on acquiring the
vector without a need for a locked operation to release it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes the Rx buffer allocation at the end of ixgbe_clean_rx_irq.
The reason for removing this is to avoid the extra latency introduced by the
MMIO write. This can amount to somewhere around an extra 100ns of latency and
one extra message worth of PCIe bus overhead.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves warnings produced by ixgbe in W=2 kernel
builds. There are missing-field-initializers warnings and shadow
warnings. None of these point to any deeper problem, so just
resolve them so any new warnings get analyzed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ixgbe to drop the ixgbe_get_headlen function in favor of eth_get_headlen.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we previously called ixgbe_set_num_queues just prior to attempting
to set our interrupt scheme, it may be non obvious why we have to call
it again inside the function. Add a comment which helps make it more
obvious that we are resetting features based on the fact that we do not
have MSI-X enabled, and cannot use the previous settings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe initiates a reset of the interface on link loss with pending Tx work
in order to clear the rings.
This patch extends the pending Tx work check to the VF interfaces with the
same purpose.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the behavior for FDB handling is consistent
between both the SR-IOV and non-SR-IOV cases. The main change here is that we
perform bounds checking on the number of SR-IOV addresses regardless of if
SR-IOV is enabled or not as we can only support a certain number of addresses
in the hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When xmit_more mode is being used and the ring is about to
become full or the stack has stopped the ring, enforce a tail
pointer write to the hw. Otherwise, we could risk a TX hang.
Code suggested by Alexander Duyck.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the deferred tail pointer flush API for the ixgbe
driver. Similar version also proposed longer time ago by Alexander Duyck.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make return values more direct, eliminating some gotos and
otherwise unneeded conditionals. This also eliminates some
local variables. Also a few minor cleanups in affected code
so checkpatch won't complain.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All of the code involved with returning the supported physical
layer is actually unused, so delete it.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ixgbe_write_mbx is called and no mbx->ops.write method
exists, no error code is returned. The corresponding read
function explicitly returns an error in such a case as do
other functions, so this appears to be a minor bug. Fix
it for consistency, and generate return values directly
to make things clearer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the function ixgbe_get_swfw_sync_semaphore, an incorrect
check was treating success as failure and vice-versa. This led
to manipulating the IXGBE_SWFW_SYNC register without holding
the software semaphore first, which is an error. In addition,
if getting the REGSMP bit in the IXGBE_SW_FW_SYNC register
timed out, no error code would be returned, making the caller
think that it had successfully acquired the lock. Fix both of
those issues and clean up the function a bit, such as make the
name in the comment match the function.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Failure to acquire the semaphore would lead to a spurious release
of the semaphore in several functions. Do not release a semaphore
that you did not get.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert some udelay calls to the preferred usleep_range.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prevents the display of the minimum link qualification check
if we might be in a virtual machine. This check is incorrect and
misleading in this case, since we actually don't really know what the
available bandwidth is. To do so, we simply check whether each function
on the bus matches our device id. If it doesn't the most likely scenario
is that we're directly assigned to a virtual machine.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug in the misuse of the list_for_each macro to loop over every
entry in the bus_list. Instead of attempting to loop over the list from
a random entry point, go up to the bus and use the real list_head entry
point. This prevents the possible read or write of unallocated or
incorrectly addressed memory.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change some uses of strncpy to use the more appropriate strlcpy
when clearing is not needed to prevent information leakage. Also
change some length arguments to use the preferred sizeof form.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_probe, the code at label err_dma can dereference adapter
when it has a NULL value. The check is there to avoid disabling a
disabled device. When adapter is NULL, treat it as if the device
is enabled, because it is enabled in that case.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
v2: fixed issue with checking return of dcbnl_rtnl_ops->getapp()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPS signal is not correct, as it generates a one half HZ clock
signal, as it only generates one level change per second. To generate a
full clock, we need two level changes per second. Also, change the name
of the #define, in order to prevent confusion between it and
NSEC_PER_SEC which is not guaranteed to be a 64bit value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
We don't need this header file, so we shouldn't be including it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
