Device ID comparison in igc_is_device_id_i226 is performed before
the ID is set, resulting in always failing check on init.
Before the patch:
* L1.2 is not disabled on init
* L1.2 is properly disabled after suspend-resume cycle
With the patch:
* L1.2 is properly disabled both on init and after suspend-resume
How to test:
Connect to the 1G link with 300+ mbit/s Internet speed, and run
the download speed test, such as:
curl -o /dev/null http://speedtest.selectel.ru/1GB
Without L1.2 disabled, the speed would be no more than ~200 mbit/s.
With L1.2 disabled, the speed would reach 1 gbit/s.
Note: it's required that the latency between your host and the remote
be around 3-5 ms, the test inside LAN (<1 ms latency) won't trigger the
issue.
Link: https://lore.kernel.org/intel-wired-lan/15248b4f-3271-42dd-8e35-02bfc92b25e1@intel.com
Fixes: 0325143b59 ("igc: disable L1.2 PCI-E link substate to avoid performance issue")
Signed-off-by: ValdikSS <iam@valdikss.org.ru>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250819222000.3504873-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce support for a lowest priority wildcard (catch-all) rule in
ethtool's Network Flow Classification (NFC) for the igc driver. The
wildcard rule directs all unmatched network traffic, including traffic not
captured by Receive Side Scaling (RSS), to a specified queue. This
functionality utilizes the Default Queue feature available in I225/I226
hardware.
The implementation has been validated on Intel ADL-S systems with two
back-to-back connected I226 network interfaces.
Testing Procedure:
1. On the Device Under Test (DUT), verify the initial statistic:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 0
rx_queue_1_packets: 0
rx_queue_2_packets: 0
rx_queue_3_packets: 0
2. From the Link Partner, send 10 ARP packets:
$ arping -c 10 -I enp170s0 169.254.1.2
3. On the DUT, verify the packet reception on Queue 0:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 10
rx_queue_1_packets: 0
rx_queue_2_packets: 0
rx_queue_3_packets: 0
4. On the DUT, add a wildcard rule to route all packets to Queue 3:
$ sudo ethtool -N enp1s0 flow-type ether queue 3
5. From the Link Partner, send another 10 ARP packets:
$ arping -c 10 -I enp170s0 169.254.1.2
6. Now, packets are routed to Queue 3 by the wildcard (Default Queue) rule:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 10
rx_queue_1_packets: 0
rx_queue_2_packets: 0
rx_queue_3_packets: 10
7. On the DUT, add a EtherType rule to route ARP packet to Queue 1:
$ sudo ethtool -N enp1s0 flow-type ether proto 0x0806 queue 1
8. From the Link Partner, send another 10 ARP packets:
$ arping -c 10 -I enp170s0 169.254.1.2
9. Now, packets are routed to Queue 1 by the EtherType rule because it is
higher priority than the wildcard (Default Queue) rule:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 10
rx_queue_1_packets: 10
rx_queue_2_packets: 0
rx_queue_3_packets: 10
10. On the DUT, delete all the NFC rules:
$ sudo ethtool -N enp1s0 delete 63
$ sudo ethtool -N enp1s0 delete 64
11. From the Link Partner, send another 10 ARP packets:
$ arping -c 10 -I enp170s0 169.254.1.2
12. Now, packets are routed to Queue 0 because the value of Default Queue
is reset back to 0:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 20
rx_queue_1_packets: 10
rx_queue_2_packets: 0
rx_queue_3_packets: 10
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Co-developed-by: Blanco Alcaine Hector <hector.blanco.alcaine@intel.com>
Signed-off-by: Blanco Alcaine Hector <hector.blanco.alcaine@intel.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-07-03
Vladimir Oltean converts Intel drivers (ice, igc, igb, ixgbe, i40e) to
utilize new timestamping API (ndo_hwtstamp_get() and ndo_hwtstamp_set()).
For ixgbe:
Paul, Don, Slawomir, and Radoslaw add Malicious Driver Detection (MDD)
support for X550 and E610 devices to detect, report, and handle
potentially malicious VFs.
Simon Horman corrects spelling mistakes.
For igbvf:
Kohei Enju removes a couple of unreported counters and adds reporting
of Tx timeouts.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igbvf: add tx_timeout_count to ethtool statistics
igbvf: remove unused interrupt counter fields from struct igbvf_adapter
ixgbe: spelling corrections
ixgbe: turn off MDD while modifying SRRCTL
ixgbe: add Tx hang detection unhandled MDD
ixgbe: check for MDD events
ixgbe: add MDD support
i40e: convert to ndo_hwtstamp_get() and ndo_hwtstamp_set()
ixgbe: convert to ndo_hwtstamp_get() and ndo_hwtstamp_set()
igb: convert to ndo_hwtstamp_get() and ndo_hwtstamp_set()
igc: convert to ndo_hwtstamp_get() and ndo_hwtstamp_set()
ice: convert to ndo_hwtstamp_get() and ndo_hwtstamp_set()
====================
Link: https://patch.msgid.link/20250703174242.3829277-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
New timestamping API was introduced in commit 66f7223039 ("net: add
NDOs for configuring hardware timestamping") from kernel v6.6.
It is time to convert the Intel igc driver to the new API, so that
timestamping configuration can be removed from the ndo_eth_ioctl() path
completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
I226 devices advertise support for the PCI-E link L1.2 substate. However,
due to a hardware limitation, the exit latency from this low-power state
is longer than the packet buffer can tolerate under high traffic
conditions. This can lead to packet loss and degraded performance.
To mitigate this, disable the L1.2 substate. The increased power draw
between L1.1 and L1.2 is insignificant.
Fixes: 4354621173 ("igc: Add new device ID's")
Link: https://lore.kernel.org/intel-wired-lan/15248b4f-3271-42dd-8e35-02bfc92b25e1@intel.com
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
igc already supports enabling MAC Merge for FPE. This patch adds
support for preemptible queues in mqprio.
Tested preemption with mqprio by:
1. Enable FPE:
ethtool --set-mm enp1s0 pmac-enabled on tx-enabled on verify-enabled on
2. Enable preemptible queue in mqprio:
mqprio num_tc 4 map 0 1 2 3 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 1@3 \
fp P P P E
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Changes:
1. Introduce tx_enabled flag to control preemptible queue. tx_enabled
is set via mmsv module based on multiple factors, including link
up/down status, to determine if FPE is active or inactive.
2. Add priority field to TXDCTL for express queue to improve data
fetch performance.
3. Block preemptible queue setup in taprio unless reverse-tsn-txq-prio
private flag is set. Encourages adoption of standard queue priority
scheme for new features.
4. Hardware-padded frames from preemptible queues result in incorrect
mCRC values, as padding bytes are excluded from the computation. Pad
frames to at least 60 bytes using skb_padto() before transmission to
ensure the hardware includes padding in the mCRC calculation.
Tested preemption with taprio by:
1. Enable FPE:
ethtool --set-mm enp1s0 pmac-enabled on tx-enabled on verify-enabled on
2. Enable private flag to reverse TX queue priority:
ethtool --set-priv-flags enp1s0 reverse-txq-prio on
3. Enable preemptible queue in taprio:
taprio num_tc 4 map 0 1 2 3 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 1@3 \
fp P P P E
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Co-developed-by: Chwee-Lin Choong <chwee.lin.choong@intel.com>
Signed-off-by: Chwee-Lin Choong <chwee.lin.choong@intel.com>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
By default, igc assigns TX hw queue 0 the highest priority and queue 3
the lowest. This is opposite of most NICs, where TX hw queue 3 has the
highest priority and queue 0 the lowest.
mqprio in igc already uses TX arbitration unconditionally to reverse TX
queue priority when mqprio is enabled. The TX arbitration logic does not
require a private flag, because mqprio was added recently and no known
users depend on the default queue ordering, which differs from the typical
convention.
taprio does not use TX arbitration, so it inherits the default igc TX
queue priority order. This causes tc command inconsistencies when
configuring frame preemption with taprio compared to mqprio in igc.
Other tc command inconsistencies and configuration issues already exist
when using taprio on igc compared to other network controllers. These
issues are described in a later section.
To harmonize TX queue priority behavior between taprio and mqprio, and
to fix these issues without breaking long-standing taprio use cases,
this patch adds a new private flag, called reverse-tsn-txq-prio, to
reverse the TX queue priority. It makes queue 3 the highest and queue 0
the lowest, reusing the TX arbitration logic already used by mqprio.
Users must set the private flag when enabling frame preemption with
taprio to follow the standard convention. Doing so promotes adoption of
the correct priority model for new features while preserving
compatibility with legacy configurations.
This new private flag addresses:
1. Non-standard socket -> tc -> TX hw queue mapping for taprio in igc
Without the private flag:
- taprio maps (socket -> tc -> TX hardware queue) differently on igc
compared to other network controllers
- On igc, mqprio maps tc differently from taprio, since mqprio already
uses TX arbitration
The following examples compare taprio configuration on igc and other
network controllers:
a) On other NICs (TX hw queue 3 is highest priority):
taprio num_tc 4 map 0 1 2 3 .... \
queues 1@0 1@1 1@2 1@3
Mapping translates to:
socket 0 -> tc 0 -> queue 0
socket 3 -> tc 3 -> queue 3
This is the normal mapping that respects the standard convention:
higher socket number -> higher tc -> higher priority TX hw queue
b) On igc (TX hw queue 0 is highest priority by default):
taprio num_tc 4 map 3 2 1 0 .... \
queues 1@0 1@1 1@2 1@3
Mapping translates to:
socket 0 -> tc 3 -> queue 3
socket 3 -> tc 0 -> queue 0
This igc tc mapping example is based on Intel's TSN validation test
case, where a higher socket priority maps to a higher priority queue.
It respects the mapping:
higher socket number -> higher priority TX hw queue
but breaks the expected ordering:
higher tc -> higher priority TX hw queue
as defined in [Ref1]. This custom mapping complicates common taprio
setup across NICs.
2. Non-standard frame preemption mapping for taprio in igc
Without the private flag:
- Compared to other network controllers, taprio on igc must flip the
expected fp sequence, since express traffic is expected to map to the
highest priority queue and preemptible traffic to lower ones
- On igc, frame preemption configuration for mqprio differs from taprio,
since mqprio already uses TX arbitration
The following examples compare taprio frame preemption configuration on
igc and other network controllers:
a) On other NICs (TX hw queue 3 is highest priority):
taprio num_tc 4 map ..... \
queues 1@0 1@1 1@2 1@3 \
fp P P P E
Mapping translates to:
tc0, tc1, tc2 -> preemptible -> queue 0, 1, 2
tc3 -> express -> queue 3
This is the normal mapping that respects the standard convention:
higher tc -> express traffic -> higher priority TX hw queue
lower tc -> preemptible traffic -> lower priority TX hw queue
b) On igc (TX hw queue 0 is highest priority by default):
taprio num_tc 4 map ...... \
queues 1@0 1@1 1@2 1@3 \
fp E P P P
Mapping translates to:
tc0 -> express -> queue 0
tc1, tc2, tc3 -> preemptible -> queue 1, 2, 3
This inversion respects the mapping of:
express traffic -> higher priority TX hw queue
but breaks the expected ordering:
higher tc -> express traffic
as defined in [Ref1] where higher tc indicates higher priority. In
this case, the lower tc0 is assigned to express traffic. This custom
mapping further complicates common preemption setup across NICs.
Tests were performed on taprio with the following combinations, where
two apps send traffic simultaneously on different queues:
Private Flag Traffic Sent By Traffic Sent By
----------------------------------------------------------------
enabled iperf3 (queue 3) iperf3 (queue 0)
disabled iperf3 (queue 0) iperf3 (queue 3)
enabled iperf3 (queue 3) real-time app (queue 0)
disabled iperf3 (queue 0) real-time app (queue 3)
enabled real-time app (queue 3) iperf3 (queue 0)
disabled real-time app (queue 0) iperf3 (queue 3)
enabled real-time app (queue 3) real-time app (queue 0)
disabled real-time app (queue 0) real-time app (queue 3)
Private flag is controlled with:
ethtool --set-priv-flags enp1s0 reverse-tsn-txq-prio <on|off>
[Ref1]
IEEE 802.1Q clause 8.6.8 Transmission selection:
"For a given Port and traffic class, frames are selected from the
corresponding queue for transmission if and only if:
...
b) For each queue corresponding to a numerically higher value of traffic
class supported by the Port, the operation of the transmission selection
algorithm supported by that queue determines that there is no frame
available for transmission."
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously, TX arbitration prioritized queues based on the TC they were
mapped to. A queue mapped to TC 3 had higher priority than one mapped to
TC 0.
To improve code reuse for upcoming patches and align with typical NIC
behavior, this patch updates the logic to prioritize higher queue numbers
when mqprio is used. As a result, queue 0 becomes the lowest priority and
queue 3 becomes the highest.
This patch also introduces igc_tsn_is_tc_to_queue_priority_ordered() to
preserve the original TC-based priority rule and reject configurations
where a higher TC maps to a lower queue offset.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor TXDCTL macro handling to use FIELD_PREP and GENMASK macros.
This prepares the code for adding a new TXDCTL priority field in an
upcoming patch.
Verified that the macro values remain unchanged before and after
refactoring.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rename macros to use the DCTL prefix for consistency with existing
macros that reference the same register. This prepares for an upcoming
patch that adds new fields to TXDCTL.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
Limit netdev_tc calls to MQPRIO. Currently these calls are made in
igc_tsn_enable_offload() and igc_tsn_disable_offload() which are used by
TAPRIO and ETF as well. However, these are only required for MQPRIO.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since preemptible tc implementation is not ready yet, block it from being
set in taprio. The existing code already blocks it in mqprio.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch implements the "ethtool --set-mm" callback to trigger the
frame preemption verification handshake.
Uses the MAC Merge Software Verification (mmsv) mechanism in ethtool
to perform the verification handshake for igc.
The structure fpe.mmsv is set by mmsv in ethtool and should remain
read-only for the driver.
Other mmsv callbacks:
a) configure_tx() -> not used yet at this point
- igc lacks registers to configure FPE in the transmit direction, so
this API is not utilized for now. When igc supports preemptible queue,
driver will use this API to manage its configuration.
b) configure_pmac() -> not used
- this callback dynamically controls pmac_enabled at runtime. For
example, mmsv calls configure_pmac() and disables pmac_enabled when
the link partner goes down, even if the user previously enabled it.
The intention is to save power but it is not feasible in igc
because it causes an endless adapter reset loop:
1) Board A and Board B complete the verification handshake. Tx mode
register for both boards are in TSN mode.
2) Board B link goes down.
On Board A:
3) mmsv calls configure_pmac() with pmac_enabled = false.
4) configure_pmac() in igc updates a new field based on pmac_enabled.
Driver uses this field in igc_tsn_new_flags() to indicate that the
user enabled/disabled FPE.
5) configure_pmac() in igc calls igc_tsn_offload_apply() to check
whether an adapter reset is needed. Calls existing logic in
igc_tsn_will_tx_mode_change() and igc_tsn_new_flags().
6) Since pmac_enabled is now disabled and no other TSN feature is
active, igc_tsn_will_tx_mode_change() evaluates to true because Tx
mode will switch from TSN to Legacy.
7) Driver resets the adapter.
8) Registers are set, and Tx mode switches to Legacy.
9) When link partner is up, steps 3-8 repeat, but this time with
pmac_enabled = true, reactivating TSN.
igc_tsn_will_tx_mode_change() evaluates to true again, since Tx
mode will switch from Legacy to TSN.
10) Driver resets the adapter.
11) Adapter reset completes, registers are set, and Tx mode switches to
TSN.
On Board B:
12) Adapter reset on Board A at step 10 causes it to detect its link
partner as down.
13) Repeats steps 3-8.
14) Once reset adapter on Board A is completed at step 11, it detects
its link partner as up.
15) Repeats steps 9-11.
- this cycle repeats indefinitely. To avoid this issue, igc only uses
mmsv.pmac_enabled to track whether FPE is enabled or disabled.
Co-developed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Co-developed-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Co-developed-by: Chwee-Lin Choong <chwee.lin.choong@intel.com>
Signed-off-by: Chwee-Lin Choong <chwee.lin.choong@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rename RX and TX packet buffer size macros in preparation for an
upcoming patch that will refactor buffer size handling using FIELD_PREP
and GENMASK.
Changes:
- Rename I225_RXPBSIZE_DEFAULT to IGC_RXPBSIZE_EXP_BMC_DEFAULT.
The EXP_BMC suffix explicitly indicates Express and BMC buffer
default values, improving readability and reusability for the
upcoming changes, while also better reflecting the current buffer
allocations.
- Rename I225_TXPBSIZE_DEFAULT to IGC_TXPBSIZE_DEFAULT.
These registers apply to both i225 and i226, so using the IGC prefix
aligns with existing macro naming conventions.
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Renamed xdp_get_tx_ring() function to a more generic name for use in
upcoming frame preemption patches.
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is enabled by default in other Intel drivers I've checked (e1000, e1000e,
iavf, igb and ice). Fixes an out-of-the-box performance issue when running
OpenWrt on typical mini-PCs with igc-supported Ethernet controllers and 802.1Q
VLAN configurations, as ethtool isn't part of the default packages and sane
defaults are expected.
In my specific case, with an Intel N100-based machine with four I226-V Ethernet
controllers, my upload performance increased from under 30 Mb/s to the expected
~1 Gb/s.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make sure that the PTP module is cleaned up if the igc_probe() fails by
calling igc_ptp_stop() on exit.
Fixes: d89f88419f ("igc: Add skeletal frame for Intel(R) 2.5G Ethernet Controller support")
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fixes TX frame drops in AF_XDP zero copy mode when budget < 4.
xsk_tx_peek_desc() consumed TX frame and it was ignored because of
low budget. Not even AF_XDP completion was done for dropped frames.
It can be reproduced on i226 by sending 100000x 60 B frames with
launch time set to minimal IPG (672 ns between starts of frames)
on 1Gbit/s. Always 1026 frames are not sent and are missing a
completion.
Fixes: 9acf59a752 ("igc: Enable TX via AF_XDP zero-copy")
Signed-off-by: Zdenek Bouska <zdenek.bouska@siemens.com>
Reviewed-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Florian Bezdeka <florian.bezdeka@siemens.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In commit b65969856d ("igc: Link queues to NAPI instances"), the XSK
queues were incorrectly unmapped from their NAPI instances. After
discussion on the mailing list and the introduction of a test to codify
the expected behavior, we can see that the unmapping causes the
check_xsk test to fail:
NETIF=enp86s0 ./tools/testing/selftests/drivers/net/queues.py
[...]
# Check| ksft_eq(q.get('xsk', None), {},
# Check failed None != {} xsk attr on queue we configured
not ok 4 queues.check_xsk
After this commit, the test passes:
ok 4 queues.check_xsk
Note that the test itself is only in net-next, so I tested this change
by applying it to my local net-next tree, booting, and running the test.
Cc: stable@vger.kernel.org
Fixes: b65969856d ("igc: Link queues to NAPI instances")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Core & protocols
----------------
- Continue Netlink conversions to per-namespace RTNL lock
(IPv4 routing, routing rules, routing next hops, ARP ioctls).
- Continue extending the use of netdev instance locks. As a driver
opt-in protect queue operations and (in due course) ethtool
operations with the instance lock and not RTNL lock.
- Support collecting TCP timestamps (data submitted, sent, acked)
in BPF, allowing for transparent (to the application) and lower
overhead tracking of TCP RPC performance.
- Tweak existing networking Rx zero-copy infra to support zero-copy
Rx via io_uring.
- Optimize MPTCP performance in single subflow mode by 29%.
- Enable GRO on packets which went thru XDP CPU redirect (were queued
for processing on a different CPU). Improving TCP stream performance
up to 2x.
- Improve performance of contended connect() by 200% by searching
for an available 4-tuple under RCU rather than a spin lock.
Bring an additional 229% improvement by tweaking hash distribution.
- Avoid unconditionally touching sk_tsflags on RX, improving
performance under UDP flood by as much as 10%.
- Avoid skb_clone() dance in ping_rcv() to improve performance under
ping flood.
- Avoid FIB lookup in netfilter if socket is available, 20% perf win.
- Rework network device creation (in-kernel) API to more clearly
identify network namespaces and their roles.
There are up to 4 namespace roles but we used to have just 2 netns
pointer arguments, interpreted differently based on context.
- Use sysfs_break_active_protection() instead of trylock to avoid
deadlocks between unregistering objects and sysfs access.
- Add a new sysctl and sockopt for capping max retransmit timeout
in TCP.
- Support masking port and DSCP in routing rule matches.
- Support dumping IPv4 multicast addresses with RTM_GETMULTICAST.
- Support specifying at what time packet should be sent on AF_XDP
sockets.
- Expose TCP ULP diagnostic info (for TLS and MPTCP) to non-admin users.
- Add Netlink YAML spec for WiFi (nl80211) and conntrack.
- Introduce EXPORT_IPV6_MOD() and EXPORT_IPV6_MOD_GPL() for symbols
which only need to be exported when IPv6 support is built as a module.
- Age FDB entries based on Rx not Tx traffic in VxLAN, similar
to normal bridging.
- Allow users to specify source port range for GENEVE tunnels.
- netconsole: allow attaching kernel release, CPU ID and task name
to messages as metadata
Driver API
----------
- Continue rework / fixing of Energy Efficient Ethernet (EEE) across
the SW layers. Delegate the responsibilities to phylink where possible.
Improve its handling in phylib.
- Support symmetric OR-XOR RSS hashing algorithm.
- Support tracking and preserving IRQ affinity by NAPI itself.
- Support loopback mode speed selection for interface selftests.
Device drivers
--------------
- Remove the IBM LCS driver for s390.
- Remove the sb1000 cable modem driver.
- Add support for SFP module access over SMBus.
- Add MCTP transport driver for MCTP-over-USB.
- Enable XDP metadata support in multiple drivers.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- add PCIe TLP Processing Hints (TPH) support for new AMD platforms
- support dumping RoCE queue state for debug
- opt into instance locking
- Intel (100G, ice, idpf):
- ice: rework MSI-X IRQ management and distribution
- ice: support for E830 devices
- iavf: add support for Rx timestamping
- iavf: opt into instance locking
- nVidia/Mellanox:
- mlx4: use page pool memory allocator for Rx
- mlx5: support for one PTP device per hardware clock
- mlx5: support for 200Gbps per-lane link modes
- mlx5: move IPSec policy check after decryption
- AMD/Solarflare:
- support FW flashing via devlink
- Cisco (enic):
- use page pool memory allocator for Rx
- enable 32, 64 byte CQEs
- get max rx/tx ring size from the device
- Meta (fbnic):
- support flow steering and RSS configuration
- report queue stats
- support TCP segmentation
- support IRQ coalescing
- support ring size configuration
- Marvell/Cavium:
- support AF_XDP
- Wangxun:
- support for PTP clock and timestamping
- Huawei (hibmcge):
- checksum offload
- add more statistics
- Ethernet virtual:
- VirtIO net:
- aggressively suppress Tx completions, improve perf by 96% with
1 CPU and 55% with 2 CPUs
- expose NAPI to IRQ mapping and persist NAPI settings
- Google (gve):
- support XDP in DQO RDA Queue Format
- opt into instance locking
- Microsoft vNIC:
- support BIG TCP
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- cleanup Tx and Tx clock setting and other link-focused cleanups
- enable SGMII and 2500BASEX mode switching for Intel platforms
- support Sophgo SG2044
- Broadcom switches (b53):
- support for BCM53101
- TI:
- iep: add perout configuration support
- icssg: support XDP
- Cadence (macb):
- implement BQL
- Xilinx (axinet):
- support dynamic IRQ moderation and changing coalescing at runtime
- implement BQL
- report standard stats
- MediaTek:
- support phylink managed EEE
- Intel:
- igc: don't restart the interface on every XDP program change
- RealTek (r8169):
- support reading registers of internal PHYs directly
- increase max jumbo packet size on RTL8125/RTL8126
- Airoha:
- support for RISC-V NPU packet processing unit
- enable scatter-gather and support MTU up to 9kB
- Tehuti (tn40xx):
- support cards with TN4010 MAC and an Aquantia AQR105 PHY
- Ethernet PHYs:
- support for TJA1102S, TJA1121
- dp83tg720: add randomized polling intervals for link detection
- dp83822: support changing the transmit amplitude voltage
- support for LEDs on 88q2xxx
- CAN:
- canxl: support Remote Request Substitution bit access
- flexcan: add S32G2/S32G3 SoC
- WiFi:
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
- batman-adv: add support for jumbo frames
- WiFi drivers:
- RealTek (rtw88):
- support RTL8814AE and RTL8814AU
- RealTek (rtw89):
- switch using wiphy_lock and wiphy_work
- add BB context to manipulate two PHY as preparation of MLO
- improve BT-coexistence mechanism to play A2DP smoothly
- Intel (iwlwifi):
- add new iwlmld sub-driver for latest HW/FW combinations
- MediaTek (mt76):
- preparation for mt7996 Multi-Link Operation (MLO) support
- Qualcomm/Atheros (ath12k):
- continued work on MLO
- Silabs (wfx):
- Wake-on-WLAN support
- Bluetooth:
- add support for skb TX SND/COMPLETION timestamping
- hci_core: enable buffer flow control for SCO/eSCO
- coredump: log devcd dumps into the monitor
- Bluetooth drivers:
- intel: add support to configure TX power
- nxp: handle bootloader error during cmd5 and cmd7
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XY0S
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Continue Netlink conversions to per-namespace RTNL lock
(IPv4 routing, routing rules, routing next hops, ARP ioctls)
- Continue extending the use of netdev instance locks. As a driver
opt-in protect queue operations and (in due course) ethtool
operations with the instance lock and not RTNL lock.
- Support collecting TCP timestamps (data submitted, sent, acked) in
BPF, allowing for transparent (to the application) and lower
overhead tracking of TCP RPC performance.
- Tweak existing networking Rx zero-copy infra to support zero-copy
Rx via io_uring.
- Optimize MPTCP performance in single subflow mode by 29%.
- Enable GRO on packets which went thru XDP CPU redirect (were queued
for processing on a different CPU). Improving TCP stream
performance up to 2x.
- Improve performance of contended connect() by 200% by searching for
an available 4-tuple under RCU rather than a spin lock. Bring an
additional 229% improvement by tweaking hash distribution.
- Avoid unconditionally touching sk_tsflags on RX, improving
performance under UDP flood by as much as 10%.
- Avoid skb_clone() dance in ping_rcv() to improve performance under
ping flood.
- Avoid FIB lookup in netfilter if socket is available, 20% perf win.
- Rework network device creation (in-kernel) API to more clearly
identify network namespaces and their roles. There are up to 4
namespace roles but we used to have just 2 netns pointer arguments,
interpreted differently based on context.
- Use sysfs_break_active_protection() instead of trylock to avoid
deadlocks between unregistering objects and sysfs access.
- Add a new sysctl and sockopt for capping max retransmit timeout in
TCP.
- Support masking port and DSCP in routing rule matches.
- Support dumping IPv4 multicast addresses with RTM_GETMULTICAST.
- Support specifying at what time packet should be sent on AF_XDP
sockets.
- Expose TCP ULP diagnostic info (for TLS and MPTCP) to non-admin
users.
- Add Netlink YAML spec for WiFi (nl80211) and conntrack.
- Introduce EXPORT_IPV6_MOD() and EXPORT_IPV6_MOD_GPL() for symbols
which only need to be exported when IPv6 support is built as a
module.
- Age FDB entries based on Rx not Tx traffic in VxLAN, similar to
normal bridging.
- Allow users to specify source port range for GENEVE tunnels.
- netconsole: allow attaching kernel release, CPU ID and task name to
messages as metadata
Driver API:
- Continue rework / fixing of Energy Efficient Ethernet (EEE) across
the SW layers. Delegate the responsibilities to phylink where
possible. Improve its handling in phylib.
- Support symmetric OR-XOR RSS hashing algorithm.
- Support tracking and preserving IRQ affinity by NAPI itself.
- Support loopback mode speed selection for interface selftests.
Device drivers:
- Remove the IBM LCS driver for s390
- Remove the sb1000 cable modem driver
- Add support for SFP module access over SMBus
- Add MCTP transport driver for MCTP-over-USB
- Enable XDP metadata support in multiple drivers
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- add PCIe TLP Processing Hints (TPH) support for new AMD
platforms
- support dumping RoCE queue state for debug
- opt into instance locking
- Intel (100G, ice, idpf):
- ice: rework MSI-X IRQ management and distribution
- ice: support for E830 devices
- iavf: add support for Rx timestamping
- iavf: opt into instance locking
- nVidia/Mellanox:
- mlx4: use page pool memory allocator for Rx
- mlx5: support for one PTP device per hardware clock
- mlx5: support for 200Gbps per-lane link modes
- mlx5: move IPSec policy check after decryption
- AMD/Solarflare:
- support FW flashing via devlink
- Cisco (enic):
- use page pool memory allocator for Rx
- enable 32, 64 byte CQEs
- get max rx/tx ring size from the device
- Meta (fbnic):
- support flow steering and RSS configuration
- report queue stats
- support TCP segmentation
- support IRQ coalescing
- support ring size configuration
- Marvell/Cavium:
- support AF_XDP
- Wangxun:
- support for PTP clock and timestamping
- Huawei (hibmcge):
- checksum offload
- add more statistics
- Ethernet virtual:
- VirtIO net:
- aggressively suppress Tx completions, improve perf by 96%
with 1 CPU and 55% with 2 CPUs
- expose NAPI to IRQ mapping and persist NAPI settings
- Google (gve):
- support XDP in DQO RDA Queue Format
- opt into instance locking
- Microsoft vNIC:
- support BIG TCP
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- cleanup Tx and Tx clock setting and other link-focused
cleanups
- enable SGMII and 2500BASEX mode switching for Intel platforms
- support Sophgo SG2044
- Broadcom switches (b53):
- support for BCM53101
- TI:
- iep: add perout configuration support
- icssg: support XDP
- Cadence (macb):
- implement BQL
- Xilinx (axinet):
- support dynamic IRQ moderation and changing coalescing at
runtime
- implement BQL
- report standard stats
- MediaTek:
- support phylink managed EEE
- Intel:
- igc: don't restart the interface on every XDP program change
- RealTek (r8169):
- support reading registers of internal PHYs directly
- increase max jumbo packet size on RTL8125/RTL8126
- Airoha:
- support for RISC-V NPU packet processing unit
- enable scatter-gather and support MTU up to 9kB
- Tehuti (tn40xx):
- support cards with TN4010 MAC and an Aquantia AQR105 PHY
- Ethernet PHYs:
- support for TJA1102S, TJA1121
- dp83tg720: add randomized polling intervals for link detection
- dp83822: support changing the transmit amplitude voltage
- support for LEDs on 88q2xxx
- CAN:
- canxl: support Remote Request Substitution bit access
- flexcan: add S32G2/S32G3 SoC
- WiFi:
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
- batman-adv: add support for jumbo frames
- WiFi drivers:
- RealTek (rtw88):
- support RTL8814AE and RTL8814AU
- RealTek (rtw89):
- switch using wiphy_lock and wiphy_work
- add BB context to manipulate two PHY as preparation of MLO
- improve BT-coexistence mechanism to play A2DP smoothly
- Intel (iwlwifi):
- add new iwlmld sub-driver for latest HW/FW combinations
- MediaTek (mt76):
- preparation for mt7996 Multi-Link Operation (MLO) support
- Qualcomm/Atheros (ath12k):
- continued work on MLO
- Silabs (wfx):
- Wake-on-WLAN support
- Bluetooth:
- add support for skb TX SND/COMPLETION timestamping
- hci_core: enable buffer flow control for SCO/eSCO
- coredump: log devcd dumps into the monitor
- Bluetooth drivers:
- intel: add support to configure TX power
- nxp: handle bootloader error during cmd5 and cmd7"
* tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1681 commits)
unix: fix up for "apparmor: add fine grained af_unix mediation"
mctp: Fix incorrect tx flow invalidation condition in mctp-i2c
net: usb: asix: ax88772: Increase phy_name size
net: phy: Introduce PHY_ID_SIZE — minimum size for PHY ID string
net: libwx: fix Tx L4 checksum
net: libwx: fix Tx descriptor content for some tunnel packets
atm: Fix NULL pointer dereference
net: tn40xx: add pci-id of the aqr105-based Tehuti TN4010 cards
net: tn40xx: prepare tn40xx driver to find phy of the TN9510 card
net: tn40xx: create swnode for mdio and aqr105 phy and add to mdiobus
net: phy: aquantia: add essential functions to aqr105 driver
net: phy: aquantia: search for firmware-name in fwnode
net: phy: aquantia: add probe function to aqr105 for firmware loading
net: phy: Add swnode support to mdiobus_scan
gve: add XDP DROP and PASS support for DQ
gve: update XDP allocation path support RX buffer posting
gve: merge packet buffer size fields
gve: update GQ RX to use buf_size
gve: introduce config-based allocation for XDP
gve: remove xdp_xsk_done and xdp_xsk_wakeup statistics
...
The linked series wants to add skb tx completion timestamps.
That needs a bit in skb_shared_info.tx_flags, but all are in use.
A per-skb bit is only needed for features that are configured on a
per packet basis. Per socket features can be read from sk->sk_tsflags.
Per packet tsflags can be set in sendmsg using cmsg, but only those in
SOF_TIMESTAMPING_TX_RECORD_MASK.
Per packet tsflags can also be set without cmsg by sandwiching a
send inbetween two setsockopts:
val |= SOF_TIMESTAMPING_$FEATURE;
setsockopt(fd, SOL_SOCKET, SO_TIMESTAMPING, &val, sizeof(val));
write(fd, buf, sz);
val &= ~SOF_TIMESTAMPING_$FEATURE;
setsockopt(fd, SOL_SOCKET, SO_TIMESTAMPING, &val, sizeof(val));
Changing a datapath test from skb_shinfo(skb)->tx_flags to
skb->sk->sk_tsflags can change behavior in that case, as the tx_flags
is written before the second setsockopt updates sk_tsflags.
Therefore, only bits can be reclaimed that cannot be set by cmsg and
are also highly unlikely to be used to target individual packets
otherwise.
Free up the bit currently used for SKBTX_HW_TSTAMP_USE_CYCLES. This
selects between clock and free running counter source for HW TX
timestamps. It is probable that all packets of the same socket will
always use the same source.
Link: https://lore.kernel.org/netdev/cover.1739988644.git.pav@iki.fi/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://patch.msgid.link/20250225023416.2088705-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable Launch Time Control (LTC) support for XDP zero copy via XDP Tx
metadata framework.
This patch has been tested with tools/testing/selftests/bpf/xdp_hw_metadata
on Intel I225-LM Ethernet controller. Below are the test steps and result.
Test 1: Send a single packet with the launch time set to 1 s in the future.
Test steps:
1. On the DUT, start the xdp_hw_metadata selftest application:
$ sudo ./xdp_hw_metadata enp2s0 -l 1000000000 -L 1
2. On the Link Partner, send a UDP packet with VLAN priority 1 to port 9091
of the DUT.
Result:
When the launch time is set to 1 s in the future, the delta between the
launch time and the transmit hardware timestamp is 0.016 us, as shown in
printout of the xdp_hw_metadata application below.
0x562ff5dc8880: rx_desc[4]->addr=84110 addr=84110 comp_addr=84110 EoP
rx_hash: 0xE343384 with RSS type:0x1
HW RX-time: 1734578015467548904 (sec:1734578015.4675)
delta to User RX-time sec:0.0002 (183.103 usec)
XDP RX-time: 1734578015467651698 (sec:1734578015.4677)
delta to User RX-time sec:0.0001 (80.309 usec)
No rx_vlan_tci or rx_vlan_proto, err=-95
0x562ff5dc8880: ping-pong with csum=561c (want c7dd)
csum_start=34 csum_offset=6
HW RX-time: 1734578015467548904 (sec:1734578015.4675)
delta to HW Launch-time sec:1.0000 (1000000.000 usec)
0x562ff5dc8880: complete tx idx=4 addr=4018
HW Launch-time: 1734578016467548904 (sec:1734578016.4675)
delta to HW TX-complete-time sec:0.0000 (0.016 usec)
HW TX-complete-time: 1734578016467548920 (sec:1734578016.4675)
delta to User TX-complete-time sec:0.0000
(32.546 usec)
XDP RX-time: 1734578015467651698 (sec:1734578015.4677)
delta to User TX-complete-time sec:0.9999
(999929.768 usec)
HW RX-time: 1734578015467548904 (sec:1734578015.4675)
delta to HW TX-complete-time sec:1.0000 (1000000.016 usec)
0x562ff5dc8880: complete rx idx=132 addr=84110
Test 2: Send 1000 packets with a 10 ms interval and the launch time set to
500 us in the future.
Test steps:
1. On the DUT, start the xdp_hw_metadata selftest application:
$ sudo chrt -f 99 ./xdp_hw_metadata enp2s0 -l 500000 -L 1 > \
/dev/shm/result.log
2. On the Link Partner, send 1000 UDP packets with a 10 ms interval and
VLAN priority 1 to port 9091 of the DUT.
Result:
When the launch time is set to 500 us in the future, the average delta
between the launch time and the transmit hardware timestamp is 0.016 us,
as shown in the analysis of /dev/shm/result.log below. The XDP launch time
works correctly in sending 1000 packets continuously.
Min delta: 0.005 us
Avr delta: 0.016 us
Max delta: 0.031 us
Total packets forwarded: 1000
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250216093430.957880-6-yoong.siang.song@intel.com
Refactor the code for inserting an empty frame into a new function
igc_insert_empty_frame(). This change extracts the logic for inserting
an empty packet from igc_xmit_frame_ring() into a separate function,
allowing it to be reused in future implementations, such as the XDP
zero copy transmit function.
Remove the igc_desc_unused() checking in igc_init_tx_empty_descriptor()
because the number of descriptors needed is guaranteed.
Ensure that skb allocation and DMA mapping work for the empty frame,
before proceeding to fill in igc_tx_buffer info, context descriptor,
and data descriptor.
Rate limit the error messages for skb allocation and DMA mapping failures.
Update the comment to indicate that the 2 descriptors needed by the empty
frame are already taken into consideration in igc_xmit_frame_ring().
Handle the case where the insertion of an empty frame fails and explain
the reason behind this handling.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250216093430.957880-5-yoong.siang.song@intel.com
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/baeaabb84aef1803dfae385f6e9614d6fc547667.1738746872.git.namcao@linutronix.de
Set the buffer type to IGC_TX_BUFFER_TYPE_SKB for empty frame in the
igc_init_empty_frame function. This ensures that the buffer type is
correctly identified and handled during Tx ring cleanup.
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Cc: stable@vger.kernel.org # 6.2+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixes HW RX timestamp in the following scenario:
- AF_PACKET socket with enabled HW RX timestamps is created
- AF_XDP socket with enabled zero copy is created
- frame is forwarded to the BPF program, where the timestamp should
still be readable (extracted by igc_xdp_rx_timestamp(), kfunc
behind bpf_xdp_metadata_rx_timestamp())
- the frame got XDP_PASS from BPF program, redirecting to the stack
- AF_PACKET socket receives the frame with HW RX timestamp
Moves the skb timestamp setting from igc_dispatch_skb_zc() to
igc_construct_skb_zc() so that igc_construct_skb_zc() is similar to
igc_construct_skb().
This issue can also be reproduced by running:
# tools/testing/selftests/bpf/xdp_hw_metadata enp1s0
When a frame with the wrong port 9092 (instead of 9091) is used:
# echo -n xdp | nc -u -q1 192.168.10.9 9092
then the RX timestamp is missing and xdp_hw_metadata prints:
skb hwtstamp is not found!
With this fix or when copy mode is used:
# tools/testing/selftests/bpf/xdp_hw_metadata -c enp1s0
then RX timestamp is found and xdp_hw_metadata prints:
found skb hwtstamp = 1736509937.852786132
Fixes: 069b142f58 ("igc: Add support for PTP .getcyclesx64()")
Signed-off-by: Zdenek Bouska <zdenek.bouska@siemens.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Bezdeka <florian.bezdeka@siemens.com>
Reviewed-by: Song Yoong Siang <yoong.siang.song@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link queues to NAPI instances via netdev-genl API so that users can
query this information with netlink. Handle a few cases in the driver:
1. Link/unlink the NAPIs when XDP is enabled/disabled
2. Handle IGC_FLAG_QUEUE_PAIRS enabled and disabled
Example output when IGC_FLAG_QUEUE_PAIRS is enabled:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump queue-get --json='{"ifindex": 2}'
[{'id': 0, 'ifindex': 2, 'napi-id': 8193, 'type': 'rx'},
{'id': 1, 'ifindex': 2, 'napi-id': 8194, 'type': 'rx'},
{'id': 2, 'ifindex': 2, 'napi-id': 8195, 'type': 'rx'},
{'id': 3, 'ifindex': 2, 'napi-id': 8196, 'type': 'rx'},
{'id': 0, 'ifindex': 2, 'napi-id': 8193, 'type': 'tx'},
{'id': 1, 'ifindex': 2, 'napi-id': 8194, 'type': 'tx'},
{'id': 2, 'ifindex': 2, 'napi-id': 8195, 'type': 'tx'},
{'id': 3, 'ifindex': 2, 'napi-id': 8196, 'type': 'tx'}]
Since IGC_FLAG_QUEUE_PAIRS is enabled, you'll note that the same NAPI ID
is present for both rx and tx queues at the same index, for example
index 0:
{'id': 0, 'ifindex': 2, 'napi-id': 8193, 'type': 'rx'},
{'id': 0, 'ifindex': 2, 'napi-id': 8193, 'type': 'tx'},
To test IGC_FLAG_QUEUE_PAIRS disabled, a test system was booted using
the grub command line option "maxcpus=2" to force
igc_set_interrupt_capability to disable IGC_FLAG_QUEUE_PAIRS.
Example output when IGC_FLAG_QUEUE_PAIRS is disabled:
$ lscpu | grep "On-line CPU"
On-line CPU(s) list: 0,2
$ ethtool -l enp86s0 | tail -5
Current hardware settings:
RX: n/a
TX: n/a
Other: 1
Combined: 2
$ cat /proc/interrupts | grep enp
144: [...] enp86s0
145: [...] enp86s0-rx-0
146: [...] enp86s0-rx-1
147: [...] enp86s0-tx-0
148: [...] enp86s0-tx-1
1 "other" IRQ, and 2 IRQs for each of RX and Tx, so we expect netlink to
report 4 IRQs with unique NAPI IDs:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 2}'
[{'id': 8196, 'ifindex': 2, 'irq': 148},
{'id': 8195, 'ifindex': 2, 'irq': 147},
{'id': 8194, 'ifindex': 2, 'irq': 146},
{'id': 8193, 'ifindex': 2, 'irq': 145}]
Now we examine which queues these NAPIs are associated with, expecting
that since IGC_FLAG_QUEUE_PAIRS is disabled each RX and TX queue will
have its own NAPI instance:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump queue-get --json='{"ifindex": 2}'
[{'id': 0, 'ifindex': 2, 'napi-id': 8193, 'type': 'rx'},
{'id': 1, 'ifindex': 2, 'napi-id': 8194, 'type': 'rx'},
{'id': 0, 'ifindex': 2, 'napi-id': 8195, 'type': 'tx'},
{'id': 1, 'ifindex': 2, 'napi-id': 8196, 'type': 'tx'}]
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250106221929.956999-15-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link IRQs to NAPI instances via netdev-genl API so that users can query
this information with netlink.
Compare the output of /proc/interrupts (noting that IRQ 128 is the
"other" IRQ which does not appear to have a NAPI instance):
$ cat /proc/interrupts | grep enp86s0 | cut --delimiter=":" -f1
128
129
130
131
132
The output from netlink shows the mapping of NAPI IDs to IRQs (again
noting that 128 is absent as it is the "other" IRQ):
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 2}'
[{'defer-hard-irqs': 0,
'gro-flush-timeout': 0,
'id': 8196,
'ifindex': 2,
'irq': 132},
{'defer-hard-irqs': 0,
'gro-flush-timeout': 0,
'id': 8195,
'ifindex': 2,
'irq': 131},
{'defer-hard-irqs': 0,
'gro-flush-timeout': 0,
'id': 8194,
'ifindex': 2,
'irq': 130},
{'defer-hard-irqs': 0,
'gro-flush-timeout': 0,
'id': 8193,
'ifindex': 2,
'irq': 129}]
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250106221929.956999-14-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
igc_xdp_run_prog() converts customed xdp action to a negative error code
with the sk_buff pointer type which be checked with IS_ERR in
igc_clean_rx_irq(). Remove this error pointer handing instead use plain
int return value to fix this smatch warnings:
drivers/net/ethernet/intel/igc/igc_main.c:2533
igc_xdp_run_prog() warn: passing zero to 'ERR_PTR'
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250106221929.956999-9-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The last uses of igc_read_pcie_cap_reg() and igc_write_pcie_cap_reg()
were removed in 2019 by
commit 16ecd8d9af ("igc: Remove the obsolete workaround")
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102174142.200700-4-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
igc_read_pci_cfg() and igc_write_pci_cfg were added in 2018 as part of
commit 146740f9ab ("igc: Add support for PF")
but have remained unused.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102174142.200700-3-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the igc driver doesn't support forced speed configuration and
its current related hardware doesn't support it either, there is no
use of the mac.autoneg parameter. Moreover, in one case this usage
might result in a NULL pointer dereference due to an uninitialized
function pointer, phy.ops.force_speed_duplex.
Therefore, remove this parameter from the igc code.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Call rtnl_unlock() on this error path, before returning.
Fixes: bc23aa949a ("igc: Add pcie error handler support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the igc with XDP/ZC in busy polling mode with deferral of hard
interrupts, interrupts still happen from time to time. That is caused by
the igc task watchdog which triggers Rx interrupts periodically.
That mechanism has been introduced to overcome skb/memory allocation
failures [1]. So the Rx clean functions stop processing the Rx ring in case
of such failure. The task watchdog triggers Rx interrupts periodically in
the hope that memory became available in the mean time.
The current behavior is undesirable for real time applications, because the
driver induced Rx interrupts trigger also the softirq processing. However,
all real time packets should be processed by the application which uses the
busy polling method.
Therefore, only trigger the Rx interrupts in case of real allocation
failures. Introduce a new flag for signaling that condition.
[1] - https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/?id=3be507547e6177e5c808544bd6a2efa2c7f1d436
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for offloading MQPRIO. The hardware has four priorities as well
as four queues. Each queue must be a assigned with a unique priority.
However, the priorities are only considered in TSN Tx mode. There are two
TSN Tx modes. In case of MQPRIO the Qbv capability is not required.
Therefore, use the legacy TSN Tx mode, which performs strict priority
arbitration.
Example for mqprio with hardware offload:
|tc qdisc replace dev ${INTERFACE} handle 100 parent root mqprio num_tc 4 \
| map 0 0 0 0 0 1 2 3 0 0 0 0 0 0 0 0 \
| queues 1@0 1@1 1@2 1@3 \
| hw 1
The mqprio Qdisc also allows to configure the `preemptible_tcs'. However,
frame preemption is not supported yet.
Tested on Intel i225 and implemented by following data sheet section 7.5.2,
Transmit Scheduling.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When user issues these cmds:
1. Either a) or b)
a) mqprio with hardware offload disabled
b) taprio with txtime-assist feature enabled
2. etf
3. tc qdisc delete
4. taprio with base time in the past
At step 4, qbv_config_change_errors wrongly increased by 1.
Excerpt from IEEE 802.1Q-2018 8.6.9.3.1:
"If AdminBaseTime specifies a time in the past, and the current schedule
is running, then: Increment ConfigChangeError counter"
qbv_config_change_errors should only increase if base time is in the past
and no taprio is active. In user perspective, taprio was not active when
first triggered at step 4. However, i225/6 reuses qbv for etf, so qbv is
enabled with a dummy schedule at step 2 where it enters
igc_tsn_enable_offload() and qbv_count got incremented to 1. At step 4, it
enters igc_tsn_enable_offload() again, qbv_count is incremented to 2.
Because taprio is running, tc_setup_type is TC_SETUP_QDISC_ETF and
qbv_count > 1, qbv_config_change_errors value got incremented.
This issue happens due to reliance on qbv_count field where a non-zero
value indicates that taprio is running. But qbv_count increases
regardless if taprio is triggered by user or by other tsn feature. It does
not align with qbv_config_change_errors expectation where it is only
concerned with taprio triggered by user.
Fixing this by relocating the qbv_config_change_errors logic to
igc_save_qbv_schedule(), eliminating reliance on qbv_count and its
inaccuracies from i225/6's multiple uses of qbv feature for other TSN
features.
The new function created: igc_tsn_is_taprio_activated_by_user() uses
taprio_offload_enable field to indicate that the current running taprio
was triggered by user, instead of triggered by non-qbv feature like etf.
Fixes: ae4fe46983 ("igc: Add qbv_config_change_errors counter")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Following the implementation of "igc: Add TransmissionOverrun counter"
patch, when a taprio command is triggered by user, igc processes two
commands: TAPRIO_CMD_REPLACE followed by TAPRIO_CMD_STATS. However, both
commands unconditionally pass through igc_tsn_offload_apply() which
evaluates and triggers reset adapter. The double reset causes issues in
the calculation of adapter->qbv_count in igc.
TAPRIO_CMD_REPLACE command is expected to reset the adapter since it
activates qbv. It's unexpected for TAPRIO_CMD_STATS to do the same
because it doesn't configure any driver-specific TSN settings. So, the
evaluation in igc_tsn_offload_apply() isn't needed for TAPRIO_CMD_STATS.
To address this, commands parsing are relocated to
igc_tsn_enable_qbv_scheduling(). Commands that don't require an adapter
reset will exit after processing, thus avoiding igc_tsn_offload_apply().
Fixes: d3750076d4 ("igc: Add TransmissionOverrun counter")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240730173304.865479-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the kernel's 'ethtool_keee' structure is in use, the internal
'eee_advert' field becomes pointless and can be removed.
This patch comes to clean up this redundant code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are moving away from the Sourceforge email address. Rather than
removing or updating the email for the affected entries, remove the
MODULE_AUTHOR altogether as its usage is incorrect [1].
Link: https://lore.kernel.org/netdev/20200626115236.7f36d379@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/ [1]
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com> # libeth, libie
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The commit 01cf893bf0 ("net: intel: i40e/igc: Remove setting Autoneg in
EEE capabilities") removed SUPPORTED_Autoneg field but left inappropriate
ethtool_keee structure initialization. When "ethtool --show <device>"
(get_eee) invoke, the 'ethtool_keee' structure was accidentally overridden.
Remove the 'ethtool_keee' overriding and add EEE declaration as per IEEE
specification that allows reporting Energy Efficient Ethernet capabilities.
Examples:
Before fix:
ethtool --show-eee enp174s0
EEE settings for enp174s0:
EEE status: not supported
After fix:
EEE settings for enp174s0:
EEE status: disabled
Tx LPI: disabled
Supported EEE link modes: 100baseT/Full
1000baseT/Full
2500baseT/Full
Fixes: 01cf893bf0 ("net: intel: i40e/igc: Remove setting Autoneg in EEE capabilities")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-6-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- optimize DMA sync calls when they are no-ops (Alexander Lobakin)
- fix swiotlb padding for untrusted devices (Michael Kelley)
- add documentation for swiotb (Michael Kelley)
-----BEGIN PGP SIGNATURE-----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=Pa8W
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- optimize DMA sync calls when they are no-ops (Alexander Lobakin)
- fix swiotlb padding for untrusted devices (Michael Kelley)
- add documentation for swiotb (Michael Kelley)
* tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping:
dma: fix DMA sync for drivers not calling dma_set_mask*()
xsk: use generic DMA sync shortcut instead of a custom one
page_pool: check for DMA sync shortcut earlier
page_pool: don't use driver-set flags field directly
page_pool: make sure frag API fields don't span between cachelines
iommu/dma: avoid expensive indirect calls for sync operations
dma: avoid redundant calls for sync operations
dma: compile-out DMA sync op calls when not used
iommu/dma: fix zeroing of bounce buffer padding used by untrusted devices
swiotlb: remove alloc_size argument to swiotlb_tbl_map_single()
Documentation/core-api: add swiotlb documentation
During successful probe, igc logs this:
[ 5.133667] igc 0000:01:00.0 (unnamed net_device) (uninitialized): PHC added
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The reason is that igc_ptp_init() is called very early, even before
register_netdev() has been called. So the netdev_info() call works
on a partially uninitialized netdev.
Fix this by calling igc_ptp_init() after register_netdev(), right
after the media autosense check, just as in igb. Add a comment,
just as in igb.
Now the log message is fine:
[ 5.200987] igc 0000:01:00.0 eth0: PHC added
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
