Initialize TSPLL after initializing PHC in ice_ptp.c instead of calling
for each product in PHC init in ice_ptp_hw.c.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
TSPLL can fail when trying to lock to TIME_REF as a clock source, e.g.
when the external clock source is not stable or connected to the board.
To continue operation after failure, try to lock again to internal TCXO
and inform user about this.
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To ensure proper operation, wait for 10 to 20 microseconds before
enabling TSPLL.
Adjust wait time after enabling TSPLL from 1-5 ms to 1-2 ms.
Those values are empirical and tested on multiple HW configurations.
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add helpers for checking TSPLL params, disabling sticky bits,
configuring TSPLL and getting default clock frequency to simplify
the code flows.
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Switch from unions with bitfield structs to definitions with bitfield
masks. This is necessary, because some registers have different
field definitions or even use a different register for the same fields
based on HW type.
Remove unused register fields.
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After programming the TSPLL, re-read the registers before reporting status.
This ensures the debug log message will show what was actually programmed,
rather than relying on a cached value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When programming the Clock Generation Unit for E285-C hardware, we need
to clear the time_sync_en bit of the DWORD 9 before we set the
frequency.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a helper function to print new/current TSPLL config. This helps
avoid unnecessary casts from u8 to enums.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of multiple comments, use designated initializers for TSPLL
consts.
Adjust ice_tspll_params_e82x fields sizes.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove ice_tspll_params_e825 definitions as according to EDS (Electrical
Design Specification) doc, E825 devices support only 156.25 MHz TSPLL
frequency for both TCXO and TIME_REF clock source.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The E825-C hardware has a slightly different register layout for register
19 of the Clock Generation Unit and TSPLL. The fbdiv_intgr value can be 10
bits wide.
Additionally, most of the fields that were in register 24 are made
available in register 23 instead. The programming logic already has a
corrected definition for register 23, but it incorrectly still used the
8-bit definition of fbdiv_intgr. This results in truncating some of the
values of fbdiv_intgr, including the value used for the 156.25MHz signal.
The driver only used register 24 to obtain the enable status, which we
should read from register 23. This results in an incorrect output for the
log messages, but does not change any functionality besides
disabled-by-default dynamic debug messages.
Fix the register definitions, and adjust the code to properly reflect the
enable/disable status in the log messages.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rename TSPLL and CGU functions, definitions etc. to match the file name
and have consistent naming scheme.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Collect TSPLL related functions and definitions and move them to
a separate file to have all TSPLL functionality in one place.
Move CGU related functions and definitions to ice_common.*
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
