Only a single VSI can be in charge of sending LLDP frames, sometimes it is
beneficial to assign this function to a VF, that is possible to do with tc
capabilities in the switchdev mode. It requires first blocking the PF from
sending the LLDP frames with a following command:
tc filter add dev <ifname> egress protocol lldp flower skip_sw action drop
Then it becomes possible to configure a forward rule from a VF port
representor to uplink instead.
tc filter add dev <vf_ifname> ingress protocol lldp flower skip_sw
action mirred egress redirect dev <ifname>
How LLDP exclusivity was done previously is LLDP traffic was blocked for a
whole port by a single rule and PF was bypassing that. Now at least in the
switchdev mode, every separate VSI has to have its own drop rule. Another
complication is the fact that tc does not respect when the driver refuses
to delete a rule, so returning an error results in a HW rule still present
with no way to reference it through tc. This is addressed by allowing the
PF rule to be deleted at any time, but making the VF forward rule "dormant"
in such case, this means it is deleted from HW but stays in tc and driver's
bookkeeping to be restored when drop rule is added back to the PF.
Implement tc configuration handling which enables the user to transmit LLDP
packets from VF instead of PF.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
tc clsact qdisc allows us to add offloaded egress rules with commands such
as the following one:
tc filter add dev <ifname> egress protocol lldp flower skip_sw action drop
Support the egress rule drop action when added to PF, with a few caveats:
* in switchdev mode, all PF traffic has to go uplink with an exception for
LLDP that can be delegated to a single VSI at a time
* in legacy mode, we cannot delegate LLDP functionality to another VSI, so
such packets from PF should not be blocked.
Also, simplify the rule direction logic, it was previously derived from
actions, but actually can be inherited from the tc block (and flipped in
case of port representors).
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After switchdev is enabled and disabled later, LLDP packets sending stops,
despite working perfectly fine before and during switchdev state.
To reproduce (creating/destroying VF is what triggers the reconfiguration):
devlink dev eswitch set pci/<address> mode switchdev
echo '2' > /sys/class/net/<ifname>/device/sriov_numvfs
echo '0' > /sys/class/net/<ifname>/device/sriov_numvfs
This happens because LLDP relies on the destination override functionality.
It needs to 1) set a flag in the descriptor, 2) set the VSI permission to
make it valid. The permissions are set when the PF VSI is first configured,
but switchdev then enables it for the uplink VSI (which is always the PF)
once more when configured and disables when deconfigured, which leads to
software-generated LLDP packets being blocked.
Do not modify the destination override permissions when configuring
switchdev, as the enabled state is the default configuration that is never
modified.
Fixes: 1a1c40df2e ("ice: set and release switchdev environment")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As part of switchdev environment setup, uplink VSI is configured as
default for both Tx and Rx. Default Rx VSI is also used by promiscuous
mode. If promisc mode is enabled and an attempt to enter switchdev mode
is made, the setup will fail because Rx VSI is already configured as
default (rule exists).
Reproducer:
devlink dev eswitch set $PF1_PCI mode switchdev
ip l s $PF1 up
ip l s $PF1 promisc on
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
In switchdev setup, use ice_set_dflt_vsi() instead of plain
ice_cfg_dflt_vsi(), which avoids repeating setting default VSI for Rx if
it's already configured.
Fixes: 50d62022f4 ("ice: default Tx rule instead of to queue")
Reported-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/PH0PR11MB50138B635F2E5CEB7075325D961F2@PH0PR11MB5013.namprd11.prod.outlook.com
Reviewed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unloading the ice driver while switchdev port representors are added to
a bridge can lead to kernel panic. Reproducer:
modprobe ice
devlink dev eswitch set $PF1_PCI mode switchdev
ip link add $BR type bridge
ip link set $BR up
echo 2 > /sys/class/net/$PF1/device/sriov_numvfs
sleep 2
ip link set $PF1 master $BR
ip link set $VF1_PR master $BR
ip link set $VF2_PR master $BR
ip link set $PF1 up
ip link set $VF1_PR up
ip link set $VF2_PR up
ip link set $VF1 up
rmmod irdma ice
When unloading the driver, ice_eswitch_detach() is eventually called as
part of VF freeing. First, it removes a port representor from xarray,
then unregister_netdev() is called (via repr->ops.rem()), finally
representor is deallocated. The problem comes from the bridge doing its
own deinit at the same time. unregister_netdev() triggers a notifier
chain, resulting in ice_eswitch_br_port_deinit() being called. It should
set repr->br_port = NULL, but this does not happen since repr has
already been removed from xarray and is not found. Regardless, it
finishes up deallocating br_port. At this point, repr is still not freed
and an fdb event can happen, in which ice_eswitch_br_fdb_event_work()
takes repr->br_port and tries to use it, which causes a panic (use after
free).
Note that this only happens with 2 or more port representors added to
the bridge, since with only one representor port, the bridge deinit is
slightly different (ice_eswitch_br_port_deinit() is called via
ice_eswitch_br_ports_flush(), not ice_eswitch_br_port_unlink()).
Trace:
Oops: general protection fault, probably for non-canonical address 0xf129010fd1a93284: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: maybe wild-memory-access in range [0x8948287e8d499420-0x8948287e8d499427]
(...)
Workqueue: ice_bridge_wq ice_eswitch_br_fdb_event_work [ice]
RIP: 0010:__rht_bucket_nested+0xb4/0x180
(...)
Call Trace:
(...)
ice_eswitch_br_fdb_find+0x3fa/0x550 [ice]
? __pfx_ice_eswitch_br_fdb_find+0x10/0x10 [ice]
ice_eswitch_br_fdb_event_work+0x2de/0x1e60 [ice]
? __schedule+0xf60/0x5210
? mutex_lock+0x91/0xe0
? __pfx_ice_eswitch_br_fdb_event_work+0x10/0x10 [ice]
? ice_eswitch_br_update_work+0x1f4/0x310 [ice]
(...)
A workaround is available: brctl setageing $BR 0, which stops the bridge
from adding fdb entries altogether.
Change the order of operations in ice_eswitch_detach(): move the call to
unregister_netdev() before removing repr from xarray. This way
repr->br_port will be correctly set to NULL in
ice_eswitch_br_port_deinit(), preventing a panic.
Fixes: fff292b47a ("ice: add VF representors one by one")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement attaching and detaching SF port representor. It is done in the
same way as the VF port representor.
SF port representor is always added or removed with devlink
lock taken.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Keep the same flow of port representor creation, but instead of general
attach function create helpers for specific representor type.
Store function pointer for add and remove representor.
Type of port representor can be also known based on VSI type, but it
is more clean to have it directly saved in port representor structure.
Add devlink lock for whole port representor creation and destruction.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since the port representors are added one by one there is no need to do
eswitch rebuild. Each port representor is detached and attached in VF
reset path.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In case of reset of VF VSI can be reallocated. To handle this case it
should be properly updated.
Reload representor as vsi->vsi_num can be different than the one stored
when representor was created.
Instead of only changing antispoof do whole VSI configuration for
eswitch.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is needed because subfunction port representor shouldn't configure
the source VSI during representor creation.
Move the code to separate function and call it only in case the VF port
representor is being created.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In case of subfunction lock will be taken for whole port creation and
removing. Do the same in VF case.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_clear_dflt_vsi() is only removing default rule. Both default RX and
TX rule should be removed during release.
If it isn't switching to switchdev, second time results in error, because
TX filter is already there.
Fix it by removing the correct set of rules.
Fixes: 50d62022f4 ("ice: default Tx rule instead of to queue")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Only moving whole files, fixing Makefile and bunch of includes.
Some changes to ice_devlink file was done even in representor part (Tx
topology), so keep it as final patch to not mess up with rebasing.
After moving to devlink folder there is no need to have such long name
for these files. Rename them to simple devlink.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Removing control plane VSI result in no information about slow-path
statistic. In current solution statistics need to be counted in driver.
Patch is based on similar implementation done by Simon Horman in nfp:
commit eadfa4c3be ("nfp: add stats and xmit helpers for representors")
Add const modifier to netdev parameter in ice_netdev_to_repr(). It isn't
(and shouldn't be) modified in the function.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add an ICE_RX_FLAG_MULTIDEV flag to Rx ring.
If it is set try to find correct port representor. Do it based on
src_vsi value stored in flex descriptor. Ids of representor pointers
stored in xarray are equal to corresponding src_vsi value. Thanks to
that we can directly get correct representor if we have src_vsi value.
Set multidev flag during ring configuration.
If the mode is switchdev, change the ring descriptor to the one that
contains src_vsi value.
PF netdev should be reconfigured, do it by calling ice_down() and
ice_up() if the netdev was up before configuring switchdev.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of getting repr::id from xa_alloc() value, set it to the
src_vsi::num_vsi value. It is unique for each PR.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For slow-path Rx and Tx PF VSI is used. There is no need to have control
plane VSI. Remove all code related to it.
Eswitch rebuild can't fail without rebuilding control plane VSI. Return
void from ice_eswitch_rebuild().
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Steer all packets that miss other rules to PF VSI. Previously in
switchdev mode, PF VSI received missed packets, but only ones marked
as Rx. Now it is receiving all missed packets.
To queue rule per PR isn't needed, because we use PF VSI instead of
control VSI now, and it's already correctly configured.
Add flag to correctly set LAN_EN bit in default Tx rule. It shouldn't
allow packet to go outside when there is a match.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tx can be done using PF netdev.
Checks before Tx are unnecessary. Checking if switchdev mode is set
seems too defensive (there is no PR netdev in legacy mode). If
corresponding VF is disabled or during reset, PR netdev also should be
down.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Changing queues used by eswitch will be done through PF netdev.
There is no need to reserve queues if the number of used queues
is known.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor ice driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Several places I changed to OR into a single variable with |= instead of
using a multi-line statement with trailing OR operators, as it
(subjectively) makes the code clearer.
A local variable vmvf_and_timeout was created and used to avoid multiple
logical ORs being __le16 converted, which shortened some lines and makes
the code cleaner.
Also clean up a couple of places where conversions were made to have the
code read more clearly/consistently.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rebuilding CP VSI each time the PR is created drastically increase the
time of maximum VFs creation. Add function to reserve number of CP
queues to deal with this problem.
Use the same function to decrease number of queues in case of removing
VFs. Assume that caller of ice_eswitch_reserve_cp_queues() will also
call ice_eswitch_attach/detach() correct number of times.
Still one by one PR adding is handy for VF resetting routine.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is no need to use specific functions for rebuilding path. Let's
use current implementation by removing all representors and as the
result remove switchdev environment.
It will be added in devices rebuild path. For example during adding VFs,
port representors for them also will be created.
Rebuild control plane VSI before removing representors with INIT_VSI
flag set to reinit VSI in hardware after reset.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement adding representors one by one. Always set switchdev
environment when first representor is being added and clear environment
when last one is being removed.
Basic switchdev configuration remains the same. Code related to creating
and configuring representor was changed.
Instead of setting whole representors in one function handle only one
representor in setup function. The same with removing representors.
Stop representors when new one is being added or removed. Stop means,
disabling napi, stopping traffic and removing slow path rule. It is
needed because ::q_id will change after remapping, so each representor
will need new rule.
When representor are stopped rebuild control plane VSI with one more or
one less queue. One more if new representor is being added, one less if
representor is being removed.
Bridge port is removed during unregister_netdev() call on PR, so there
is no need to call it from driver side.
After that do remap new queues to correct vector. At the end start all
representors (napi enable, start queues, add slow path rule).
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is needed to track correct Tx topology. Update it every time new
representor is created or remove node in case of removing corresponding
representor.
Still clear all node when removing switchdev mode as part of Tx topology
isn't related only to representors. Also clear ::rate_note value to
prevent skipping this node next time Tx topology is created.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Representor code needs to be independent from specific device type, like
in this case VF. Make generic add / remove representor function and
specific add VF / rem VF function. New device types will follow this
scheme.
In bridge offload code there is a need to get representor pointer based
on VSI. Implement helper function to achieve that.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make eswitch code generic by removing VF pointer reference in functions.
It is needed to support eswitch mode for other type of devices.
Previously queue id used for Rx was based on VF number. Use ::q_id saved
in port representor instead.
After adding or removing port representor ::q_id value can change. It
isn't good idea to iterate over representors list using this value.
Use xa_find starting from the first one instead to get next port
representor to remap.
The number of port representors has to be equal to ::num_rx/tx_q. Warn if
it isn't true.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of assuming that each VF has pointer to port representor save it
in xarray. It will allow adding port representor for other device types.
Drop reference to VF where it is use only to get port representor. Get
it from xarray instead.
The functions will no longer by specific for VF, rename them.
Track id assigned by xarray in port representor structure. The id can't
be used as ::q_id, because it is fixed during port representor lifetime.
::q_id can change after adding / removing other port representors.
Side effect of removing VF pointer is that we are losing VF MAC
information used in unrolling. Store it in port representor as parent
MAC.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously queue index of control plane VSI used by port representor was
always id of VF. If we want to allow adding port representors for
different devices we have to track queue index in the port representor
structure.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It isn't used in ice_eswitch_release_reprs(). Probably leftover. Remove
it.
Commit that has removed usage of ctrl_vsi:
commit c1e5da5dd4 ("ice: improve switchdev's slow-path")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is a leftover from previous implementation. Accidentally it wasn't
removed. Do it now.
Commit that has removed it:
commit c1e5da5dd4 ("ice: improve switchdev's slow-path")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Eswitch is used as a prefix for related functions. Main structure
storing all data related to eswitch should also be named as eswitch
instead of ice_switchdev_info. Rename it.
Also rename switchdev to eswitch where the context is not about eswitch
mode.
::uplink_netdev was changed to netdev for simplicity. There is no other
netdev in function scope so it is obvious.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-08-17 (ice)
This series contains updates to ice driver only.
Jan removes unused functions and refactors code to make, possible,
functions static.
Jake rearranges some functions to be logically grouped.
Marcin removes an unnecessary call to disable VLAN stripping.
Yang Yingliang utilizes list_for_each_entry() helper for a couple list
traversals.
Przemek removes some parameters from ice_aq_alloc_free_res() which were
always the same and reworks ice_aq_wait_for_event() to reduce chance of
race.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: split ice_aq_wait_for_event() func into two
ice: embed &ice_rq_event_info event into struct ice_aq_task
ice: ice_aq_check_events: fix off-by-one check when filling buffer
ice: drop two params from ice_aq_alloc_free_res()
ice: use list_for_each_entry() helper
ice: Remove redundant VSI configuration in eswitch setup
ice: move E810T functions to before device agnostic ones
ice: refactor ice_vsi_is_vlan_pruning_ena
ice: refactor ice_ptp_hw to make functions static
ice: refactor ice_sched to make functions static
ice: Utilize assign_bit() helper
ice: refactor ice_vf_lib to make functions static
ice: refactor ice_lib to make functions static
ice: refactor ice_ddp to make functions static
ice: remove unused methods
====================
Link: https://lore.kernel.org/r/20230817212239.2601543-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/sfc/tc.c
fa165e1949 ("sfc: don't unregister flow_indr if it was never registered")
3bf969e88a ("sfc: add MAE table machinery for conntrack table")
https://lore.kernel.org/all/20230818112159.7430e9b4@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove a call to disable VLAN stripping on switchdev control plane VSI, as
it is disabled by default.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ADQ and switchdev are not supported simultaneously. Enabling both at the
same time can result in nullptr dereference.
To prevent this, check if ADQ is active when changing devlink mode to
switchdev mode, and check if switchdev is active when enabling ADQ.
Fixes: fbc7b27af0 ("ice: enable ndo_setup_tc support for mqprio_qdisc")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230816193405.1307580-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With this patch, ice driver is able to track if the port
representors or uplink port were added to the linux bridge in
switchdev mode. Listen for NETDEV_CHANGEUPPER events in order to
detect this. ice_esw_br data structure reflects the linux bridge
and stores all the ports of the bridge (ice_esw_br_port) in
xarray, it's created when the first port is added to the bridge and
freed once the last port is removed. Note that only one bridge is
supported per eswitch.
Bridge port (ice_esw_br_port) can be either a VF port representor
port or uplink port (ice_esw_br_port_type). In both cases bridge port
holds a reference to the VSI, VF's VSI in case of the PR and uplink
VSI in case of the uplink. VSI's index is used as an index to the
xarray in which ports are stored.
Add a check which prevents configuring switchdev mode if uplink is
already added to any bridge. This is needed because we need to listen
for NETDEV_CHANGEUPPER events to record if the uplink was added to
the bridge. Netdevice notifier is registered after eswitch mode
is changed to switchdev.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In switchdev mode uplink VSI is supposed to receive all packets that
were not matched by existing filters. If ICE_AQ_VSI_SW_FLAG_LOCAL_LB
bit is unset and we have a filter associated with uplink VSI
which matches on dst mac equal to MAC1, then packets with src mac equal
to MAC1 will be pruned from reaching uplink VSI.
Fix this by updating uplink VSI with ICE_AQ_VSI_SW_FLAG_LOCAL_LB bit
set when configuring switchdev mode.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In switchdev mode, uplink VSI is configured to be default
VSI which means it will receive all unmatched packets.
In order to receive vlan packets we need to disable vlan pruning
as well. This is done by dis_rx_filtering vlan op.
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is possibility that ice_eswitch_port_start_xmit might be
called while some resources are still not allocated which might
cause NULL pointer dereference. Fix this by checking if switchdev
configuration was finished.
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Advanced rules for ctrl VSI will be removed anyway when the
VSI will cleaned up, no need to do it explicitly.
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The use of a source MAC to direct packets from the VF to the corresponding
port representor is only ok if there is only one MAC on a VF. To support
this functionality when the number of MACs on a VF is greater, it is
necessary to match a source VSI instead of a source MAC.
Let's use the new switch API that allows matching on metadata.
If MAC isn't used in match criteria there is no need to handle adding
rule after virtchnl command. Instead add new rule while port representor
is being configured.
Remove rule_added field, checking for sp_rule can be used instead.
Remove also checking for switchdev running in deleting rule as it can be
called from unroll context when running flag isn't set. Checking for
sp_rule covers both context (with and without running flag).
Rules are added in eswitch configuration flow, so there is no need to
have replay function.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Information about the direction is currently stored in sw_act.flag.
There is no need to duplicate it in another field.
Setting direction flag doesn't mean that there is a match criteria for
direction in rule. It is only a information for HW from where switch id
should be collected (VSI or port). In current implementation of advance
rule handling, without matching for direction meta data, we can always
set one the same flag and everything will work the same.
Ability to match on direction meta data will be added in follow up
patches.
Recipe 0, 3 and 9 loaded from package has direction match
criteria, but they are handled in other function.
Move ice_adv_rule_info fields to avoid holes.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The dev_lan_addr and hw_lan_addr members of ice_vf are used only to store
the MAC address for the VF. They are defined using virtchnl_ether_addr, but
only the .addr sub-member is actually used. Drop the use of
virtchnl_ether_addr and just use a u8 array of length [ETH_ALEN].
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_vsi_setup function, ice_vsi_alloc, and ice_vsi_cfg functions have
grown a large number of parameters. These parameters are used to initialize
a new VSI, as well as re-configure an existing VSI
Any time we want to add a new parameter to this function chain, even if it
will usually be unset, we have to change many call sites due to changing
the function signature.
A future change is going to refactor ice_vsi_alloc and ice_vsi_cfg to move
the VSI configuration and initialization all into ice_vsi_cfg.
Before this, refactor the VSI setup flow to use a new ice_vsi_cfg_params
structure. This will contain the configuration (mainly pointers) used to
initialize a VSI.
Pass this from ice_vsi_setup into the related functions such as
ice_vsi_alloc, ice_vsi_cfg, and ice_vsi_cfg_def.
Introduce a helper, ice_vsi_to_params to convert an existing VSI to the
parameters used to initialize it. This will aid in the flows where we
rebuild an existing VSI.
Since we also pass the ICE_VSI_FLAG_INIT to more functions which do not
need (or cannot yet have) the VSI parameters, lets make this clear by
renaming the function parameter to vsi_flags and using a u32 instead of a
signed integer. The name vsi_flags also makes it clear that we may extend
the flags in the future.
This change will make it easier to refactor the setup flow in the future,
and will reduce the complexity required to add a new parameter for
configuration in the future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In current implementation default VSI switch filter is only able to
forward traffic to a single VSI. This limits promiscuous mode with
private flag 'vf-true-promisc-support' to a single VF. Enabling it on
the second VF won't work. Also allmulticast support doesn't seem to be
properly implemented when vf-true-promisc-support is true.
Use standard ice_add_rule_internal() function that already implements
forwarding to multiple VSI's instead of constructing AQ call manually.
Add switch filter for allmulticast mode when vf-true-promisc-support is
enabled. The same filter is added regardless of the flag - it doesn't
matter for this case.
Remove unnecessary fields in switch structure. From now on book keeping
will be done by ice_add_rule_internal().
Refactor unnecessarily passed function arguments.
To test:
1) Create 2 VM's, and two VF's. Attach VF's to VM's.
2) Enable promiscuous mode on both of them and check if
traffic is seen on both of them.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
