This patch adds reference counting support for
alloc/free mac filters
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TCAM reference counting
support for cxgb4 change mac path
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TCAM reference counting
support for raw mac filters.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove existing mps refcounting code which was
added only for encap filters and add necessary
data structures/functions to support mps reference
counting for all the mac filters. Also add wrapper
functions for allocating and freeing encap mac
filters.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spread initial IRQ affinity hints across the device node CPUs,
for nic queue and uld queue IRQs, to load balance and avoid
all interrupts on CPU0.
Signed-off-by: Nirranjan Kirubaharan <nirranjan@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for validating hardware filter spec configured in firmware
before offloading exact match flows.
Use the new fw api FW_PARAM_DEV_FILTER_MODE_MASK to read the filter mode
and mask from firmware. If the api isn't supported, then fall-back to
older way of reading just the mode from indirect register.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hash (exact-match) filters used for offloading flows share the
same active region resources on the chip with upper layer drivers,
like iw_cxgb4, chcr, etc. Currently, only either Hash filters
or ULDs can use the active region resources, but not both. Hence,
use the new firmware configuration parameters (when available)
to allow both the Hash filters and ULDs to share the
active region simultaneously.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch advertises Forward Error Correction in ethtool
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of these macros were conflicting with global namespace,
hence prefixing them with CXGB4.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ndo_set_vf_link_state to control the link states associated
with the virtual interfaces.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets/sets SGE Doorbell Queue timer ticks via ethtool
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 introduced a Timer Mechanism in SGE called the
SGE Doorbell Queue Timer. With this we can now configure
TX Queues to get CIDX Updates when:
Time(CIDX == PIDX) >= Timer
Previously we rely on TX Queue Status Page updates by hardware
for DMA completions. This will make Hardware/Firmware actually
deliver the CIDX Updates as Ingress Queue messages with
commensurate Interrupts.
So we now have a new RX Path component for processing CIDX Updates
and reclaiming TX Descriptors faster.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
{t4/t4_vf}_change_mac() API's were only doing additions to MPS_TCAM.
This will fail, when the number of tcam entries is limited particularly
in vf's.
This fix programs hash region with the mac address, when TCAM
addtion fails for {t4/t4vf}_change_mac(). Since the locally maintained
driver list for hash entries is shared across mac_{sync/unsync}(),
added an extra parameter if_mac to track the address added thorugh
{t4/t4vf}_change_mac()
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the fw supports returning VIN/VIVLD in FW_VI_CMD save it
in port_info structure else retrieve these from viid and save
them in port_info structure. Do the same for smt_idx from
FW_VI_MAC_CMD
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_THERMAL=m, we get a build error:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.c: In function 'cxgb4_thermal_get_trip_type':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.c:48:11: error: 'struct adapter' has no member named 'ch_thermal'
Once that is fixed by using IS_ENABLED() checks, we get a link error
against the thermal subsystem when cxgb4 is built-in:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_init':
cxgb4_thermal.c:(.text+0x180): undefined reference to `thermal_zone_device_register'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_remove':
cxgb4_thermal.c:(.text+0x1e0): undefined reference to `thermal_zone_device_unregister'
Finally, since CONFIG_THERMAL can be =m, the Makefile fails to pick up the
extra file into built-in.a, and we get another link failure against the
cxgb4_thermal_init/cxgb4_thermal_remove files, so the Makefile has to
be adapted as well to work for both CONFIG_THERMAL=y and =m.
Fixes: b187191577 ("cxgb4: Add thermal zone support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add thermal zone support to monitor ASIC's temperature.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
print per rx-queue packet errors in sge_qinfo
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect descriptors of all ULD and LLD hardware queues managed
by LLD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
display Data Center bridging information in debug
fs.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In highly constrained resources environments (like the 124VF
T5 and 248VF T6 configurations), PF4 may not have very many
resources at all and we need to adapt to whatever we've been
allocated, this patch adds support to get the provisioned
resources.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The present TX workrequest(FW_ETH_TX_PKT_WR) cant be used for
host->vf communication, since it doesn't loopback the outgoing
packets to virtual interfaces on the same port. This can be done
using FW_ETH_TX_PKT_VM_WR.
This fix depends on ethtool_flags to determine what WR to use for
TX path. Support for setting this flags by user is added in next
commit.
Based on the original work by : Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flag tc_flower_initialized to indicate the
completion if tc flower initialization.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the use of rhashtables in net namespaces,
rhashtable.h is included in lots of the kernel,
so a small changes can required a large recompilation.
This makes development painful.
This patch splits out rhashtable-types.h which just includes
the major type declarations, and does not include (non-trivial)
inline code. rhashtable.h is no longer included by anything
in the include/ directory.
Common include files only include rhashtable-types.h so a large
recompilation is only triggered when that changes.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a confusion of two different abstractions in the Common
Code: Physical Link (Port) and Logical Network Interface (Virtual
Interface), and we haven't been properly managing the state of the
intersection of those two abstractions.
On the one hand we have the Physical state of the Link -- up or down --
and on the other we have the logical state of the VI, enabled or not.
{ethN} refers to both the Physical and Logical State. In this case,
ifconfig only affects/interrogates the Logical State of a VI,
and ethtool only deals with the Physical State. And these are different.
So, just because we disable the VI, we don't really want to change the
Physical Link Up/Down state. Thus, the previous hack to set
"lc->link_ok = 0" when we disable a VI is completely incorrect.
Where we get into trouble is where the Physical Link State and the
Logical VI State cross swords. And that happens in
t4_handle_get_port_info() where we need to manage/safe the Physical
Link State, but we also need to know when the Logical VI State has
changed and pass that back up to the OS-dependent Driver routine
t4_os_link_changed() which is concerned about the Logical Interface.
So we enable a VI and that causes Firmware to send us a new Port
Information message, but if none of the Physical Link State
particulars have changed, we don't call t4_os_link_changed().
This fix uses the existing OS Contract APIs for the Common Code to
inform the OS-dependent portion of the Host Driver when the "Link" (really
Logical Network Interface) is "up" or "down". A new API
t4_enable_pi_params() is added which calls t4_enable_vi_params() and,
if that is successful, then calls back to the OS Contract API
t4_os_link_changed() notifying the OS-dependent layer of the
potential Link State change.
Original Work by : Casey Leedom <leedom@chelsio.com>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trigger an L1 configure operation when a transceiver module
is inserted in order to cause current "sticky" options like
Requested Forward Error Correction to be reapplied.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for matching flows based on tunnel VNI value.
Introduces fw APIs for allocating/removing MPS entries related
to encapsulation. And uses the same while adding/deleting filters
for offloading flows based on tunnel VNI match.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register callback to collect hardware/firmware dumps in second kernel
before hardware/firmware is initialized. The dumps for each device
will be available as elf notes in /proc/vmcore in second kernel.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If FW supports RDMA WRITE_COMPLETION functionality, then advertise that
to the ULDs. This will be used by iw_cxgb4 to allow WRITE_COMPLETION
work requests.
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If FW supports RDMA WRITE_WITH_IMMEDATE functionality, then advertise
that
to the ULDs. This will be used by iw_cxgb4 to allow WRITE_WITH_IMMEDIATE
work requests.
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- This patch adds support to initialise srq table and read srq entries
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
notify uld drivers if the adapter encounters fatal
error.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HMA(Host Memory Access) maps a part of host memory for T6-SO memfree cards.
This commit does the following:
- Query FW to check if we have HMA support. If yes, the params will
return HMA size configured in FW. We will dma map memory based
on this size.
- Also contains changes to get HMA memory information via debugfs.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Michael Werner <werner@chelsio.com>
Signed-off-by: Ganesh GR <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework logic to read EDC and MC. Do 32-bit reads at a time.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull crypto updates from Herbert Xu:
"API:
- Enforce the setting of keys for keyed aead/hash/skcipher
algorithms.
- Add multibuf speed tests in tcrypt.
Algorithms:
- Improve performance of sha3-generic.
- Add native sha512 support on arm64.
- Add v8.2 Crypto Extentions version of sha3/sm3 on arm64.
- Avoid hmac nesting by requiring underlying algorithm to be unkeyed.
- Add cryptd_max_cpu_qlen module parameter to cryptd.
Drivers:
- Add support for EIP97 engine in inside-secure.
- Add inline IPsec support to chelsio.
- Add RevB core support to crypto4xx.
- Fix AEAD ICV check in crypto4xx.
- Add stm32 crypto driver.
- Add support for BCM63xx platforms in bcm2835 and remove bcm63xx.
- Add Derived Key Protocol (DKP) support in caam.
- Add Samsung Exynos True RNG driver.
- Add support for Exynos5250+ SoCs in exynos PRNG driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (166 commits)
crypto: picoxcell - Fix error handling in spacc_probe()
crypto: arm64/sha512 - fix/improve new v8.2 Crypto Extensions code
crypto: arm64/sm3 - new v8.2 Crypto Extensions implementation
crypto: arm64/sha3 - new v8.2 Crypto Extensions implementation
crypto: testmgr - add new testcases for sha3
crypto: sha3-generic - export init/update/final routines
crypto: sha3-generic - simplify code
crypto: sha3-generic - rewrite KECCAK transform to help the compiler optimize
crypto: sha3-generic - fixes for alignment and big endian operation
crypto: aesni - handle zero length dst buffer
crypto: artpec6 - remove select on non-existing CRYPTO_SHA384
hwrng: bcm2835 - Remove redundant dev_err call in bcm2835_rng_probe()
crypto: stm32 - remove redundant dev_err call in stm32_cryp_probe()
crypto: axis - remove unnecessary platform_get_resource() error check
crypto: testmgr - test misuse of result in ahash
crypto: inside-secure - make function safexcel_try_push_requests static
crypto: aes-generic - fix aes-generic regression on powerpc
crypto: chelsio - Fix indentation warning
crypto: arm64/sha1-ce - get rid of literal pool
crypto: arm64/sha2-ce - move the round constant table to .rodata section
...
implement ndo_set_vf_vlan for mgmt netdevice to configure
the PCIe VF.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add geneve segmentation offload support of T6 cards.
Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
restructure the code which adds support for configuring
PCIe VF via mgmt netdevice. which was added by
commit 7829451c69 ("cxgb4: Add control net_device for
configuring PCIe VF")
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add changes to t4_eth_xmit to enable vxlan segmentation
offload support.
Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_udp_tunnel_add and ndo_udp_tunnel_del
to support vxlan tunnelling.
Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 96ac18f14a ("cxgb4: Add support for new flash parts")
removed initialization of adapter->params.sf_fw_start causing issues
while flashing firmware to card. We no longer need sf_fw_start
in adapter->params as we already have macros defined for FW flash
addresses.
Fixes: 96ac18f14a ("cxgb4: Add support for new flash parts")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS table is 4k for T6 and later cards, add check for the
same.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ethtool get_module_info() and get_module_eeprom()
callbacks that will dump necessary information for a SFP.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use meminfo to identify the egress and ingress context regions and
fetch all valid contexts from those regions. Also flush all contexts
before attempting collection to prevent stale information.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added Tx routine for ULD
- define interface for ULD Tx.
Export routines used for Tx data
- Routines common for data transmit are used by cxgb4 and chcr
drivers.
- EXPORT routines enable transmit from chcr driver.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
T6 supports ~500K hash filters and can theoretically climb up to
~1 million hash filters. Preallocated hash table is not efficient
in terms of memory usage. So, use rhashtable instead which gives
the flexibility to grow based on usage.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to create hash (exact-match) filters based on the value
of 'hash' field in ch_filter_specification.
Allocate SMT/L2T entries if DMAC-rewrite/SMAC-rewrite is requested.
Allocate CLIP entry in case of IPv6 filter.
Use cpl_act_open_req[6] to send hash filter create request to hw.
Also, the filter tuple is calculated as part of sending this request.
Hash-filter reply is processed on getting cpl_act_open_rpl.
In case of success, various bits/fields in filter-tcb are set per
filter requirement, such as enabling filter hitcnts, and/or various
header rewrite operations, such as VLAN-rewrite, NAT or
(L3/L4)-rewrite, and SMAC/DMAC-rewrite. In case of failure, clear the
filter entry and release any hw resources occupied by it.
The patch also moves the functions set_tcb_field, set_tcb_tflag and
configure_filter_smac towards beginning of file.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for hash-filter configuration on T6. Also, do basic
checks for the related initialization.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save additional filter tuple field shifts in tp_params based on
configured filter tuple fields.
Also, save the combined filter tuple mask based on configured
filter tuple fields.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect hardware TX traffic scheduler and pace tables.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support to rewrite L3/L4 fields via TC-PEDIT action.
Supported fields for rewrite are:
IPv4 src/dst address, IPv6 src/dst address, TCP/UDP sport/dport.
Also, process match fields first and then process the action items.
Refactor pedit action validation to separate function to avoid
excessive code indentation.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update driver to use new fw_filter2_wr in order to support rewrite of
L3/L4 header fields via filters. Query FW_PARAMS_PARAM_DEV_FILTER2_WR
to check whether FW supports this new wr.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce SMT operations for allocating/removing entries from
SMAC table. Make TCAM filters use the SMT ops whenever SMAC rewrite
is required.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to access TP indirect registers via firmware first. If this fails,
fallback and access them directly. This ensures that driver and
firmware do not conflict each other while accessing the TP indirect
registers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement operations to set/get dump data via ethtool. Also add
template header that precedes dump data, which helps in decoding
and extracting the dump data.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to retrieve stats from hardware for offloaded tc flower
flows. Also, poll for the stats of offloaded flows via timer callback.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to add/remove flows for offload. Following match
and action are supported for offloading a flow:
Match: ether-protocol, IPv4/IPv6 addresses, L4 ports (TCP/UDP)
Action: drop, redirect to another port on the device.
The qualifying flows can have accompanying mask information.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
do not wait for completion while deleting the filters
when the adapter is shutting down because we may not get
the response as interrupts will be disabled.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement new 32-bit Firmware Port Capabilities in order to
handle new speeds which couldn't be represented in the old 16-bit
Firmware Port Capabilities values.
Based on the original work of Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4 Ethernet driver now queries PCIe configuration space to determine
if it can send TLPs to it with the Relaxed Ordering Attribute set.
Remove the enable_pcie_relaxed_ordering() to avoid enable PCIe Capability
Device Control[Relaxed Ordering Enable] at probe routine, to make sure
the driver will not send the Relaxed Ordering TLPs to the Root Complex which
could not deal the Relaxed Ordering TLPs.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because Firmware and the Firmware Configuration File need to be
in sync; clear out any On-FLASH Firmware Configuration File when new
Firmware is loaded. This will avoid difficult to diagnose and fix
problems with a mis-matched Firmware Configuration File which prevents the
adapter from being initialized.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
print the versions of vpd and serial configuration file,
flashed to adapter, and cleanup the relevant code.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
Supports hardware and software time stamping via the
Linux SO_TIMESTAMPING socket option.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffer group mappings can be obtained using FW_PARAMs cmd for newer FW.
Since some of the bg_maps are obtained in atomic context, created another
t4_query_params_ns(), that wont sleep when awaiting mbox cmd completion.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using t4_get_mps_bg_map() for both t4_get_port_stats()
to determine which MPS Buffer Groups to report statistics on for a given
Port, and also for t4_sge_alloc_rxq() to provide a TP Ingress Channel
Congestion Map. For T4/T5 these are actually the same values (because they
are ~somewhat~ related), but for T6 they should return different values
(T6 has Port 0 associated with MPS Buffer Group 0 (with MPS Buffer Group 1
silently cascading off) and Port 1 is associated with MPS Buffer Group 2
(with 3 cascading off)).
Based on the original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_set_vf_rate() for mgmt interface to support rate-limiting
of VF traffic using 'ip' command.
Based on the original work of Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
issue get port information command to firmware to retrieve port
information and update if it is different from what was last
recorded and also add indication for supported link modes for
firmware port types FW_PORT_TYPE_SFP28, FW_PORT_TYPE_KR_SFP28,
FW_PORT_TYPE_CR4_QSFP.
Based on the original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix multiqueue in stmmac driver on PCI, from Andy Shevchenko.
2) cdc_ncm doesn't actually fully zero out the padding area is
allocates on TX, from Jim Baxter.
3) Don't leak map addresses in BPF verifier, from Daniel Borkmann.
4) If we randomize TCP timestamps, we have to do it everywhere
including SYN cookies. From Eric Dumazet.
5) Fix "ethtool -S" crash in aquantia driver, from Pavel Belous.
6) Fix allocation size for ntp filter bitmap in bnxt_en driver, from
Dan Carpenter.
7) Add missing memory allocation return value check to DSA loop driver,
from Christophe Jaillet.
8) Fix XDP leak on driver unload in qed driver, from Suddarsana Reddy
Kalluru.
9) Don't inherit MC list from parent inet connection sockets, another
syzkaller spotted gem. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
dccp/tcp: do not inherit mc_list from parent
qede: Split PF/VF ndos.
qed: Correct doorbell configuration for !4Kb pages
qed: Tell QM the number of tasks
qed: Fix VF removal sequence
qede: Fix XDP memory leak on unload
net/mlx4_core: Reduce harmless SRIOV error message to debug level
net/mlx4_en: Avoid adding steering rules with invalid ring
net/mlx4_en: Change the error print to debug print
drivers: net: wimax: i2400m: i2400m-usb: Use time_after for time comparison
DECnet: Use container_of() for embedded struct
Revert "ipv4: restore rt->fi for reference counting"
net: mdio-mux: bcm-iproc: call mdiobus_free() in error path
net: ethernet: ti: cpsw: adjust cpsw fifos depth for fullduplex flow control
ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf
net: cdc_ncm: Fix TX zero padding
stmmac: pci: split out common_default_data() helper
stmmac: pci: RX queue routing configuration
stmmac: pci: TX and RX queue priority configuration
stmmac: pci: set default number of rx and tx queues
...
There are many code paths opencoding kvmalloc. Let's use the helper
instead. The main difference to kvmalloc is that those users are
usually not considering all the aspects of the memory allocator. E.g.
allocation requests <= 32kB (with 4kB pages) are basically never failing
and invoke OOM killer to satisfy the allocation. This sounds too
disruptive for something that has a reasonable fallback - the vmalloc.
On the other hand those requests might fallback to vmalloc even when the
memory allocator would succeed after several more reclaim/compaction
attempts previously. There is no guarantee something like that happens
though.
This patch converts many of those places to kv[mz]alloc* helpers because
they are more conservative.
Link: http://lkml.kernel.org/r/20170306103327.2766-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> # Xen bits
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Andreas Dilger <andreas.dilger@intel.com> # Lustre
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> # KVM/s390
Acked-by: Dan Williams <dan.j.williams@intel.com> # nvdim
Acked-by: David Sterba <dsterba@suse.com> # btrfs
Acked-by: Ilya Dryomov <idryomov@gmail.com> # Ceph
Acked-by: Tariq Toukan <tariqt@mellanox.com> # mlx4
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx5
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: "Yan, Zheng" <zyan@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent Chelsio firmware started using few port capablity bits to
manage FEC and as driver was not aware of FEC changes those bits
were zeroed, consequently disabling FEC.
Avoid zeroing those bits and default to whatever the firmware
tells us the Link is currently advertising.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot of code, we also remove one spin_lock()
from driver fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform an emergency shutdown of the adapter and stop it from
continuing any further communication on the ports or DMA to the
host. This is typically used when the adapter and/or firmware
have crashed and we want to prevent any further accidental
communication with the rest of the world. This will also force
the port Link Status to go down -- if register writes work --
which should help our peers figure out that we're down.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue comes when there are multiple threads attempting to use
the mailbox facility at the same time.
When DCB operations and interface up/down is run in a loop for every
0.1 sec, we observed mailbox collisions. And out of the two commands
one would fail with the present code, since we don't queue the second
command.
To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at
the head issue the mailbox command, else wait for the existing command
to complete. Usually command takes less than a milli-second to
complete.
Also timeout from the loop, if the command under execution takes
long time to run.
In reality, the number of mailbox access collisions is going to be
very rare since no one runs such abusive script.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t6fw-1.15.15.0 enabled compressed error vector in cpl_rx_pkt for T6.
Updating driver to take care of these changes.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate resources dynamically for Upper layer driver's (ULD) like
cxgbit, iw_cxgb4, cxgb4i and chcr. The resources allocated include Tx
queues which are allocated when ULD register with cxgb4 driver and freed
while un-registering. The Tx queues which are shared by ULD shall be
allocated by first registering driver and un-allocated by last
unregistering driver.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates to mlx5
- Updates to mlx4 (two conflicts, both minor and easily resolved)
- Updates to iw_cxgb4 (one conflict, not so obvious to resolve, proper
resolution is to keep the code in cxgb4_main.c as it is in Linus'
tree as attach_uld was refactored and moved into cxgb4_uld.c)
- Improvements to uAPI (moved vendor specific API elements to uAPI area)
- Add hns-roce driver and hns and hns-roce ACPI reset support
- Conversion of all rdma code away from deprecated
create_singlethread_workqueue
- Security improvement: remove unsafe ib_get_dma_mr (breaks lustre in
staging)
-----BEGIN PGP SIGNATURE-----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=LC+S
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull main rdma updates from Doug Ledford:
"This is the main pull request for the rdma stack this release. The
code has been through 0day and I had it tagged for linux-next testing
for a couple days.
Summary:
- updates to mlx5
- updates to mlx4 (two conflicts, both minor and easily resolved)
- updates to iw_cxgb4 (one conflict, not so obvious to resolve,
proper resolution is to keep the code in cxgb4_main.c as it is in
Linus' tree as attach_uld was refactored and moved into
cxgb4_uld.c)
- improvements to uAPI (moved vendor specific API elements to uAPI
area)
- add hns-roce driver and hns and hns-roce ACPI reset support
- conversion of all rdma code away from deprecated
create_singlethread_workqueue
- security improvement: remove unsafe ib_get_dma_mr (breaks lustre in
staging)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (75 commits)
staging/lustre: Disable InfiniBand support
iw_cxgb4: add fast-path for small REG_MR operations
cxgb4: advertise support for FR_NSMR_TPTE_WR
IB/core: correctly handle rdma_rw_init_mrs() failure
IB/srp: Fix infinite loop when FMR sg[0].offset != 0
IB/srp: Remove an unused argument
IB/core: Improve ib_map_mr_sg() documentation
IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets
IB/mthca: Move user vendor structures
IB/nes: Move user vendor structures
IB/ocrdma: Move user vendor structures
IB/mlx4: Move user vendor structures
IB/cxgb4: Move user vendor structures
IB/cxgb3: Move user vendor structures
IB/mlx5: Move and decouple user vendor structures
IB/{core,hw}: Add constant for node_desc
ipoib: Make ipoib_warn ratelimited
IB/mlx4/alias_GUID: Remove deprecated create_singlethread_workqueue
IB/ipoib_verbs: Remove deprecated create_singlethread_workqueue
IB/ipoib: Remove deprecated create_singlethread_workqueue
...
Query firmware for the FW_PARAMS_PARAM_DEV_RI_FR_NSMR_TPTE_WR parameter.
If it exists and is 1, then advertise support for FR_NSMR_TPTE_WR to
the ULDs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support for offloading u32 filter onto hardware. Links are stored
in a jump table to perform necessary jumps to match TCP/UDP header.
When inserting rules in the linked bucket, the TCP/UDP match fields
in the corresponding entry of the jump table are appended to the filter
rule before insertion. If a link is deleted, then all corresponding
filters associated with the link are also deleted. Also enable
hardware tc offload as a supported feature.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable filters for non-offload configuration and add common api support
for setting and deleting filters in LE-TCAM region of the hardware.
IPv4 filters occupy one slot. IPv6 filters occupy 4 slots and must
be on a 4-slot boundary. IPv4 filters can not occupy a slot belonging
to IPv6 and the vice-versa is also true.
Filters are set and deleted asynchronously. Use completion to wait
for reply from firmware in order to allow for synchronization if needed.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move common filter code to separate files. Also fix the following
checkpatch checks.
CHECK: Comparison to NULL could be written "!f->l2t"
+ if (f->l2t == NULL) {
CHECK: spaces preferred around that '/' (ctx:VxV)
+ fwr->len16_pkd = htonl(FW_WR_LEN16_V(sizeof(*fwr)/16));
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing check for 25G and 100G while checking port speed,
which lead to less number of queues getting allocated for 25G & 100G
adapters and leading to low throughput. Adding the missing check for
both NIC and vNIC driver.
Also fixes port advertisement for 25G and 100G in ethtool output.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate resources dynamically to cxgb4's Upper layer driver's(ULD) like
cxgbit, iw_cxgb4 and cxgb4i. Allocate resources when they register with
cxgb4 driver and free them while unregistering. All the queues and the
interrupts for them will be allocated during ULD probe only and freed
during remove.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ndo_get_vf_config, also fill the default mac address
that will be provided to the VF by firmware, in case user doesn't
provide one. So user can get the default MAC address address also
through ndo_get_vf_config.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disable SRIOV, we used to unregister the netdev but wasn't
freed. But next time when the same netdev is registered, since the state
was in 'NETREG_UNREGISTERED', we used to hit BUG_ON in register_netdevice,
where it expects the state to be 'NETREG_UNINITIALIZED'.
Alloc netdev and register them while configuring SRIOV, and free them
when SRIOV is disabled. Also added a new function to setup ethernet
properties instead of using ether_setup. Set carrier off by default,
since we don't have to do any transmit on the interface.
Fixes: 7829451c69 ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set_tx_maxrate NDO to perform per queue tx rate limiting.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to bind/unbind specified tx queues to/from scheduling
classes. If a queue is already bound to a scheduling class, it is
unbound first and then bound to a new specified class.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to create tx traffic scheduling classes with specified
scheduling parameters. Return an existing class if a match is found
with same scheduling parameters.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new commmon infrastructure to allocate reosurces dynamically to
Upper layer driver's(ULD) when they register with cxgb4 driver and free
them during unregistering. All the queues and the interrupts for
them will be allocated during ULD probe only and freed during remove.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_set_vf_mac support which allows to set the MAC address
for cxgb4vf interfaces from the host
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new /sys/kernel/debug/ support to dump a firmware mailbox command
issued and replies for debugging purpose.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
