Add support for reading SFP module info and digital diagnostic
monitoring data if supported by the module. The only Aquantia
controller without an integrated PHY is the AQC100 which belongs to
the B0 revision, that's why it's only implemented there.
The register information was extracted from a diagnostic tool made
publicly available by Dell, but all code was written from scratch by me.
This has been tested to work with a variety of both optical and direct
attach modules I had lying around and seems to work fine with all of
them, including the diagnostics if supported by an optical module.
All tests have been done with an AQC100 on an TL-NT521F card on firmware
version 3.1.121 (current at the time of this patch).
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241018171721.2577386-1-lorenz@brun.one>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
W=1 builds with GCC 14.2.0 warn that:
.../aq_ethtool.c:278:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 6 [-Wformat-truncation=]
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~
.../aq_ethtool.c:278:56: note: directive argument in the range [-2147483641, 254]
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~~~~~~
.../aq_ethtool.c:278:33: note: ‘snprintf’ output between 5 and 15 bytes into a destination of size 8
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
tc is always in the range 0 - cfg->tcs. And as cfg->tcs is a u8,
the range is 0 - 255. Further, on inspecting the code, it seems
that cfg->tcs will never be more than AQ_CFG_TCS_MAX (8), so
the range is actually 0 - 8.
So, it seems that the condition that GCC flags will not occur.
But, nonetheless, it would be nice if it didn't emit the warning.
It seems that this can be achieved by changing the format specifier
from %d to %u, in which case I believe GCC recognises an upper bound
on the range of tc of 0 - 255. After some experimentation I think
this is due to the combination of the use of %u and the type of
cfg->tcs (u8).
Empirically, updating the type of the tc variable to unsigned int
has the same effect.
As both of these changes seem to make sense in relation to what the code
is actually doing - iterating over unsigned values - do both.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821-atlantic-str-v1-1-fa2cfe38ca00@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert EEE handling to use linkmode bitmaps. This prepares for
removing the legacy bitmaps from struct ethtool_keee.
No functional change intended.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/c5a61d57-d2b0-427f-93b3-fcf7721165f3@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.
This is part 1/2 of the fix, as suggested in [1]:
- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.
- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPV6 addresses are purged when setting the number of rx/tx
rings using ethtool -G. The function aq_set_ringparam
calls dev_close, which removes the addresses. As a solution,
call an internal function (aq_ndev_close).
Fixes: c1af542795 ("net: aquantia: Ethtool based ring size configuration")
Signed-off-by: Izabela Bakollari <ibakolla@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It supports XDP_PASS, XDP_DROP and multi buffer.
The new function aq_nic_xmit_xdpf() is used to send packet with
xdp_frame and internally it calls aq_nic_map_xdp().
AQC chip supports 32 multi-queues and 8 vectors(irq).
there are two option
1. under 8 cores and 4 tx queues per core.
2. under 4 cores and 8 tx queues per core.
Like ixgbe, these tx queues can be used only for XDP_TX, XDP_REDIRECT
queue. If so, no tx_lock is needed.
But this patchset doesn't use this strategy because getting hardware tx
queue index cost is too high.
So, tx_lock is used in the aq_nic_xmit_xdpf().
single-core, single queue, 80% cpu utilization.
30.75% bpf_prog_xxx_xdp_prog_tx [k] bpf_prog_xxx_xdp_prog_tx
10.35% [kernel] [k] aq_hw_read_reg <---------- here
4.38% [kernel] [k] get_page_from_freelist
single-core, 8 queues, 100% cpu utilization, half PPS.
45.56% [kernel] [k] aq_hw_read_reg <---------- here
17.58% bpf_prog_xxx_xdp_prog_tx [k] bpf_prog_xxx_xdp_prog_tx
4.72% [kernel] [k] hw_atl_b0_hw_ring_rx_receive
The new function __aq_ring_xdp_clean() is a xdp rx handler and this is
called only when XDP is attached.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mediadetect is another name for the EDPD (energy detect power down).
This feature allows device to save extra power when no link is available.
PHY goes into the extreme power saving mode and only periodically wakes up
and checks for the link.
AQC devices has fixed check period of 6 seconds
The feature may increase linkup time.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY downshift allows phy to try renegotiate if link is unstable
and can carry higher speed.
AQC devices has integrated PHY which is controlled by MAC firmware.
Thus, driver defines new ethtool callbacks to implement phy tunables
via netdev.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PTP rings statistics. Before that
these were missing from overall stats, hardening debugging
and analysis.
Signed-off-by: Pavel Belous <pbelous@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds additional per-queue stats, these could
be useful for debugging and diagnostics.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits rx and tx per-queue stats.
This change simplifies the follow-up introduction of PTP stats and
u64_stats_update_* usage.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A1 requires additional processing for both egress and ingress to support
PTP.
And it makes sense to get rid of this processing altogether (via ifdef),
if PTP clock is disabled globally.
This patch puts the PTP code under the corresponding IS_REACHABLE check.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the type for variable which is assigned from enum,
as such it should have been int, not u32.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a checkpatch warning.
Fixes: aec0f1aac5 ("net: atlantic: MACSec offload statistics implementation")
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the phy loopback support on A2.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds EEE support on A2.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Co-developed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes 2.5G baseX wrong usage/reporting, since it shouldn't have
been mixed with baseT.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for automatic queue number downgrade.
On A2: this is a must have, because only TC0/TC1 support more than 4Q.
Other TCs support 4Qs maximum.
Thus, on A2 we must downgrade the number of queues per TC to 4, if more
than 2 TCs are requested.
On A1: this allows using 8TCs even on systems with cpu count >= 8, when
we have 8 queues by default.
We will just automatically switch to 8TCx4Q mode in this case.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates TCVEC2RING to accept nic_cfg, which is needed to be able
to use it from hw_atl.
The name is updated to reflect the changes.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for per-TC queue statistics.
By default (single TC), the output is the same as it used to be, e.g.:
Queue[0] InPackets: 2
Queue[0] OutPackets: 8
Queue[0] Restarts: 0
Queue[0] InJumboPackets: 0
Queue[0] InLroPackets: 0
Queue[0] InErrors: 0
If several TCs are enabled, then each queue statistics line is prefixed
with TC number, e.g.:
TC0 Queue[0] InPackets: 6
TC0 Queue[0] OutPackets: 11
Queue numbering is end-to-end, so:
TC1 Queue[4] InPackets: 0
TC1 Queue[4] OutPackets: 22
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the constant name to a more logical "2G5"
(for 2.5G speeds).
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds defines for 10M and EEE 100M link modes, which are
supported by A2.
10M support is added in this patch series.
EEE is out of scope, but will be added in a follow-up series.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for MACSec statistics on Atlantic network cards.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver only rejected some of the unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to keep module and driver versions in in-tree
kernel code.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checks to not enable multiple loopback modes simultaneously,
It was also discovered that for dma loopback to function correctly
promisc mode should be enabled on device.
Fixes: ea4b4d7fc1 ("net: atlantic: loopback tests via private flags")
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:706:5: warning: symbol 'aq_ethtool_get_priv_flags' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:713:5: warning: symbol 'aq_ethtool_set_priv_flags' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: ea4b4d7fc1 ("net: atlantic: loopback tests via private flags")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now differentiate requested and negotiated flow control
modes. Therefore `ethtool -A` now operates on local requested
FC values, and regular link settings shows the negotiated FC
settings.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thats a pure checkpatck walkthrough the code with no functional
changes. Reverse christmas tree, spacing, etc.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we add a number of ethtool private flags
to allow enabling various loopbacks on HW.
Thats useful for verification and bringup works.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`ethtool -p eth0` will blink leds helping identify
physical port.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add ethtool msglevel configuration and change some
printouts to use netdev_info set of functions.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake on PHY allows to configure device to wakeup host
as soon as PHY link status is changed to active.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool callback with basic information on what PTP features are supported
by the device.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of FW operations could be invoked simultaneously,
from f.e. ethtool context and from service service activity work.
Here we introduce a fw mutex to secure and serialize access
to FW logic.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not careful array dereference caused analysis tools
to think there could be memory overflow.
There was actually no corruption because the array is
two dimensional.
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c: 140
aq_ethtool_get_strings() error:
memcpy() '*aq_ethtool_stat_names' too small (32 vs 704)
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of configuration of RSS hash key and RSS indirection table.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. One prominent API through which the notification is
invoked is dev_open().
Therefore extend dev_open() with and extra extack argument and update
all users. Most of the calls end up just encoding NULL, but bond and
team drivers have the extack readily available.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure to support ntuple filter configuration.
Add rule, remove rule, reapply on interface up.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control statuses were not synchronized between blocks,
that caused packets/link drop on some corner cases, when
MAC sent PFC although Phy was not expecting these to come.
Driver should readout the negotiated FC from phy and
configure RX block accordigly.
This is done on each link change event with information from FW.
Fixes: 288551de45 ("net: aquantia: Implement rx/tx flow control ethtools callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed extra spaces, corrected alignment.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support of Energy-Efficient Ethernet to aQuantia NIC's via ethtool
(according to the IEEE 802.3az specifications)
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
