JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/dsa to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/36da477cb9fa0bffec32d50c2cf3d18e94a0e7e3.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Broadcom switches supported by the b53 driver use a chip-wide jumbo frame
configuration. In the commit referenced with the Fixes tag, the setting
is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient chip-wide maximum frame size for the CPU port.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports. This aligns the driver
to the behavior of other switch drivers.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert b53 to provide its own phylink MAC operations, thus avoiding the
shim layer in DSA's port.c
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-9-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only use the PHYLINK implementation from there on now that an equivalent
configuration is applied to all of the switch ports.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-8-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
And make sure this is done for the MLO_AN_PHY case, where it actually
makes sense, contrary to b53_adjust_link() which only did it for
fixed-PHY configurations where it does not make sense.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-7-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call b53_adjust_531x5_rgmii() and b53_adjust_5325_mii() from
b53_phylink_mac_config() when we have a fixed PHY in preparation for removing
b53_adjust_link(). Also move b53_adjust_63xx_rgmii() to
b53_phylink_mac_config() where it logically belongs.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-6-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Just like what b53_adjust_link() does, force flow control for the
BCM5301X CPU port(s) by forcing rx_pause and tx_pause in
b53_phylink_mac_link_up(). Preparatory step for getting rid of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-5-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Takes care of doing the 5325 switch series specific MII programming and
is called from b53_adjust_link() to allow the future removal of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-4-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Takes care of doing the 531x5 switch series specific RGMII programming
and is called from b53_adjust_link() to allow the future removal of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-3-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
They are not used outside of the b53_common.c file, no need to be
exported.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit f86ad77faf ("net: dsa: bcm_sf2: Utilize b53_{enable,
disable}_port"), bcm_sf2.c no longer calls b53_eee_enable_set(), and all
its callers are in b53_common.c.
We also need to move it, because it is called within b53_common.c before
its definition, and we want to avoid forward declarations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240206112527.4132299-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
b53_get_mac_eee() sets both eee_enabled and eee_active, and then
returns zero.
dsa_slave_get_eee(), which calls this function, will then continue to
call phylink_ethtool_get_eee(), which will return -EOPNOTSUPP if there
is no PHY present, otherwise calling phy_ethtool_get_eee() which in
turn will call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Thus, when there is no PHY, dsa_slave_get_eee() will fail with
-EOPNOTSUPP, meaning eee_enabled and eee_active will not be returned to
userspace. When there is a PHY, eee_enabled and eee_active will be
overwritten by phylib, making the setting of these members in
b53_get_mac_eee() entirely unnecessary.
Remove this code, thus simplifying b53_get_mac_eee().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1rWbNI-002cCz-4x@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more inclusive terms throughout the DSA subsystem by moving away
from "master" which is replaced by "conduit" and "slave" which is
replaced by "user". No functional changes.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231023181729.1191071-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: FLorian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230823085632.116725-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230724211859.805481-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since DSA no longer marks anything as phylink-legacy, there is now no
need for DSA drivers to set this member to false. Remove all instances
of this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Update B53's embedded PCS driver to use neg_mode, even though it makes
no use of it or the "mode" argument. This makes the driver consistent
with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1qA8Ee-00EaGL-Az@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BCM53134 Ethernet switch in the existing b53 dsa driver.
BCM53134 is very similar to the BCM58XX series.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM6318 and BCM63268 SoCs require a special handling for their RGMIIs, so we
should be able to identify them as a special BCM63xx switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM6318, BCM6362 and BCM63268 are SoCs with a B53 MMAP switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM63xx RGMII ports require additional configuration in order to work.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230319220805.124024-1-noltari@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
CPU port should also be enabled in order to get a working switch.
Fixes: a5538a777b ("net: dsa: b53: mmap: Add device tree support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230316172807.460146-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no reason that I can see why the no-op tagging protocol should
be registered manually, so make it a module and make all drivers which
have any sort of reference to DSA_TAG_PROTO_NONE select it.
Note that I don't know if ksz_get_tag_protocol() really needs this,
or if it's just the logic which is poorly written. All switches seem to
have their own tagging protocol, and DSA_TAG_PROTO_NONE is just a
fallback that never gets used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary spi_set_drvdata() in b53_spi_remove(), the
driver_data will be set to NULL in device_unbind_cleanup() after
calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220705131733.351962-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This series includes the following patchsets:
- bitmap: optimize bitmap_weight() usage(w/o bitmap_weight_cmp), from me;
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab;
- include/linux/find: Fix documentation, from Anna-Maria Behnsen;
- bitmap: fix conversion from/to fix-sized arrays, from me;
- bitmap: Fix return values to be unsigned, from Kees Cook.
It has been in linux-next for at least a week with no problems.
-----BEGIN PGP SIGNATURE-----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=U7DN
-----END PGP SIGNATURE-----
Merge tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- bitmap: optimize bitmap_weight() usage, from me
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab
- include/linux/find: Fix documentation, from Anna-Maria Behnsen
- bitmap: fix conversion from/to fix-sized arrays, from me
- bitmap: Fix return values to be unsigned, from Kees Cook
It has been in linux-next for at least a week with no problems.
* tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux: (31 commits)
nodemask: Fix return values to be unsigned
bitmap: Fix return values to be unsigned
KVM: x86: hyper-v: replace bitmap_weight() with hweight64()
KVM: x86: hyper-v: fix type of valid_bank_mask
ia64: cleanup remove_siblinginfo()
drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
KVM: s390: replace bitmap_copy with bitmap_{from,to}_arr64 where appropriate
lib/bitmap: add test for bitmap_{from,to}_arr64
lib: add bitmap_{from,to}_arr64
lib/bitmap: extend comment for bitmap_(from,to)_arr32()
include/linux/find: Fix documentation
lib/bitmap.c make bitmap_print_bitmask_to_buf parseable
MAINTAINERS: add cpumask and nodemask files to BITMAP_API
arch/x86: replace nodes_weight with nodes_empty where appropriate
mm/vmstat: replace cpumask_weight with cpumask_empty where appropriate
clocksource: replace cpumask_weight with cpumask_empty in clocksource.c
genirq/affinity: replace cpumask_weight with cpumask_empty where appropriate
irq: mips: replace cpumask_weight with cpumask_empty where appropriate
drm/i915/pmu: replace cpumask_weight with cpumask_empty where appropriate
arch/x86: replace cpumask_weight with cpumask_empty where appropriate
...
Don't call bitmap_weight() if the following code can get by
without it.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Convert B53 to use phylink_pcs for the serdes rather than hooking it
into the MAC-layer callbacks.
Fixes: 81c1681cbb ("net: dsa: b53: mark as non-legacy")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers might have error messages to propagate to user space, most
common being that they support a single mirror port.
Propagate the netlink extack so that they can inform user space in a
verbal way of their limitations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmIdBQAACgkQJNaLcl1U
h9D1GQf/dVustBx4kCUNJt4QuMF4rozHtAzo2qK1grAnpHEqiMvVEzAuxfbTgJOx
9AUj+xEuVpPxoYUDLVJpJrxwdAl0Ue8tDRgP9Cqr/o6a3IoKrhEi+1KpSbvjcsgB
oqJEcvdjk1XAtl+QXmvyMjbMLxpz2x3Ne6dj7RL/LsfxXC0/om+NQIvJBfn78Dj2
JSNJcVtRDmdaApXfguDGA0u3COarypybYMuumIO4rRxjA5S4FXXovny4nwNXvOhS
Ki5/7GKq9rojeeIf0kD/IDdkmSS0WZp3Rc2mIrdsrXrTca+dTo3sYlcP+HMcZmtW
0+bzsht6VyApfGGZ1Ra/w3NxN6OMMg==
=TyvV
-----END PGP SIGNATURE-----
Merge tag 'spi-remove-void' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark Brown says:
====================
spi: Make remove() return void
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
====================
Link: https://lore.kernel.org/r/20220228173957.1262628-2-broonie@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As FDB isolation cannot be enforced between VLAN-aware bridges in lack
of hardware assistance like extra FID bits, it seems plausible that many
DSA switches cannot do it. Therefore, they need to reject configurations
with multiple VLAN-aware bridges from the two code paths that can
transition towards that state:
- joining a VLAN-aware bridge
- toggling VLAN awareness on an existing bridge
The .port_vlan_filtering method already propagates the netlink extack to
the driver, let's propagate it from .port_bridge_join too, to make sure
that the driver can use the same function for both.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DSA, to encourage drivers to perform FDB isolation simply means to
track which bridge does each FDB and MDB entry belong to. It then
becomes the driver responsibility to use something that makes the FDB
entry from one bridge not match the FDB lookup of ports from other
bridges.
The top-level functions where the bridge is determined are:
- dsa_port_fdb_{add,del}
- dsa_port_host_fdb_{add,del}
- dsa_port_mdb_{add,del}
- dsa_port_host_mdb_{add,del}
aka the pre-crosschip-notifier functions.
Changing the API to pass a reference to a bridge is not superfluous, and
looking at the passed bridge argument is not the same as having the
driver look at dsa_to_port(ds, port)->bridge from the ->port_fdb_add()
method.
DSA installs FDB and MDB entries on shared (CPU and DSA) ports as well,
and those do not have any dp->bridge information to retrieve, because
they are not in any bridge - they are merely the pipes that serve the
user ports that are in one or multiple bridges.
The struct dsa_bridge associated with each FDB/MDB entry is encapsulated
in a larger "struct dsa_db" database. Although only databases associated
to bridges are notified for now, this API will be the starting point for
implementing IFF_UNICAST_FLT in DSA. There, the idea is to install FDB
entries on the CPU port which belong to the corresponding user port's
port database. These are supposed to match only when the port is
standalone.
It is better to introduce the API in its expected final form than to
introduce it for bridges first, then to have to change drivers which may
have made one or more assumptions.
Drivers can use the provided bridge.num, but they can also use a
different numbering scheme that is more convenient.
DSA must perform refcounting on the CPU and DSA ports by also taking
into account the bridge number. So if two bridges request the same local
address, DSA must notify the driver twice, once for each bridge.
In fact, if the driver supports FDB isolation, DSA must perform
refcounting per bridge, but if the driver doesn't, DSA must refcount
host addresses across all bridges, otherwise it would be telling the
driver to delete an FDB entry for a bridge and the driver would delete
it for all bridges. So introduce a bool fdb_isolation in drivers which
would make all bridge databases passed to the cross-chip notifier have
the same number (0). This makes dsa_mac_addr_find() -> dsa_db_equal()
say that all bridge databases are the same database - which is
essentially the legacy behavior.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The B53 driver does not make use of the speed, duplex, pause or
advertisement in its phylink_mac_config() implementation, so it can be
marked as a non-legacy driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the Broadcom b53 driver to using the phylink_generic_validate()
implementation by removing its own .phylink_validate method and
associated code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a better method to select SFP interface modes, we
no longer need to use phylink_helper_basex_speed() in a driver's
validation function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the Broadcom
B53 DSA switches in preparation to using these for the generic
validation functionality.
The interface modes are derived from:
- b53_serdes_phylink_validate()
- SRAB mux configuration
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've stared at this if() statement for a while trying to work out if
it really does correspond with the comment above, and it does seem to.
However, let's make it more readable and phrase it in the same way as
the comment.
Also add a FIXME into the comment - we appear to deny Gigabit modes for
802.3z interface modes, but 802.3z interface modes only operate at
gigabit and above.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The 2nd param of phy_init_eee(): clk_stop_enable is a bool param, use
true or false instead of 1/0.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220123152241.1480-1-jszhang@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a preparation patch for the removal of the DSA switch methods
->port_bridge_tx_fwd_offload() and ->port_bridge_tx_fwd_unoffload().
The plan is for the switch to report whether it offloads TX forwarding
directly as a response to the ->port_bridge_join() method.
This change deals with the noisy portion of converting all existing
function prototypes to take this new boolean pointer argument.
The bool is placed in the cross-chip notifier structure for bridge join,
and a reference to it is provided to drivers. In the next change, DSA
will then actually look at this value instead of calling
->port_bridge_tx_fwd_offload().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main desire behind this is to provide coherent bridge information to
the fast path without locking.
For example, right now we set dp->bridge_dev and dp->bridge_num from
separate code paths, it is theoretically possible for a packet
transmission to read these two port properties consecutively and find a
bridge number which does not correspond with the bridge device.
Another desire is to start passing more complex bridge information to
dsa_switch_ops functions. For example, with FDB isolation, it is
expected that drivers will need to be passed the bridge which requested
an FDB/MDB entry to be offloaded, and along with that bridge_dev, the
associated bridge_num should be passed too, in case the driver might
want to implement an isolation scheme based on that number.
We already pass the {bridge_dev, bridge_num} pair to the TX forwarding
offload switch API, however we'd like to remove that and squash it into
the basic bridge join/leave API. So that means we need to pass this
pair to the bridge join/leave API.
During dsa_port_bridge_leave, first we unset dp->bridge_dev, then we
call the driver's .port_bridge_leave with what used to be our
dp->bridge_dev, but provided as an argument.
When bridge_dev and bridge_num get folded into a single structure, we
need to preserve this behavior in dsa_port_bridge_leave: we need a copy
of what used to be in dp->bridge.
Switch drivers check bridge membership by comparing dp->bridge_dev with
the provided bridge_dev, but now, if we provide the struct dsa_bridge as
a pointer, they cannot keep comparing dp->bridge to the provided
pointer, since this only points to an on-stack copy. To make this
obvious and prevent driver writers from forgetting and doing stupid
things, in this new API, the struct dsa_bridge is provided as a full
structure (not very large, contains an int and a pointer) instead of a
pointer. An explicit comparison function needs to be used to determine
bridge membership: dsa_port_offloads_bridge().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.
Use the helpers to access these elements so that we have a migration
path to the new organization.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently autoloading for SPI devices does not use the DT ID table, it
uses SPI modalises. Supporting OF modalises is going to be difficult if
not impractical, an attempt was made but has been reverted, so ensure
that module autoloading works for this driver by adding an id_table
listing the SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53 driver performs non-atomic transactions to the ARL table when
adding, deleting and reading FDB and MDB entries.
Traditionally these were all serialized by the rtnl_lock(), but now it
is possible that DSA calls ->port_fdb_add and ->port_fdb_del without
holding that lock.
So the driver must have its own serialization logic. Add a mutex and
hold it from all entry points (->port_fdb_{add,del,dump},
->port_mdb_{add,del}).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53 driver performs non-atomic transactions to the ARL table when
adding, deleting and reading FDB and MDB entries.
Traditionally these were all serialized by the rtnl_lock(), but now it
is possible that DSA calls ->port_fdb_add and ->port_fdb_del without
holding that lock.
So the driver must have its own serialization logic. Add a mutex and
hold it from all entry points (->port_fdb_{add,del,dump},
->port_mdb_{add,del}).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.
What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.
This message can be seen in a loop, and it hangs the reboot process there:
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
So why 3?
A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:
dsa_slave_create
-> netdev_upper_dev_link
-> __netdev_upper_dev_link
-> __netdev_adjacent_dev_insert
-> dev_hold
So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.
Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.
It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.
So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.
However, complications arise really quickly.
The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).
Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.
So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.
So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.
The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.
The answer to that question lies in this comment above device_link_add:
* A side effect of the link creation is re-ordering of dpm_list and the
* devices_kset list by moving the consumer device and all devices depending
* on it to the ends of these lists (that does not happen to devices that have
* not been registered when this function is called).
so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.
Fixes: 2f1e8ea726 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's set but never used anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the Broadcom's reference driver flow control needs to be
enabled for any CPU switch port (5, 7 or 8 - depending on which one is
used). Current code makes it work only for the port 5. Use
dsa_is_cpu_port() which solved that problem.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On BCM5301x port 8 requires a fixed link when used.
Years ago when b53 was an OpenWrt downstream driver (with configuration
based on sometimes bugged NVRAM) there was a need for a fixup. In case
of forcing fixed link for (incorrectly specified) port 5 the code had to
actually setup port 8 link.
For upstream b53 driver with setup based on DT there is no need for that
workaround. In DT we have and require correct ports setup.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make "enabled_ports" bitfield contain all available switch ports
including a CPU port. This way there is no need for fixup during
initialization.
For BCM53010, BCM53018 and BCM53019 include also other available ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Broadcom's b53 switches have one IMP (Inband Management Port) that needs
to be programmed using its own designed register. IMP port may be
different than CPU port - especially on devices with multiple CPU ports.
For that reason it's required to explicitly note IMP port index and
check for it when choosing a register to use.
This commit fixes BCM5301x support. Those switches use CPU port 5 while
their IMP port is 8. Before this patch b53 was trying to program port 5
with B53_PORT_OVERRIDE_CTRL instead of B53_GMII_PORT_OVERRIDE_CTRL(5).
It may be possible to also replace "cpu_port" usages with
dsa_is_cpu_port() but that is out of the scope of thix BCM5301x fix.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting DSA_MAX_PORTS caused DSA to call b53 callbacks (e.g.
b53_disable_port() during dsa_register_switch()) for invalid
(non-existent) ports. That made b53 modify unrelated registers and is
one of reasons for a broken BCM5301x support.
This problem exists for years but DSA_MAX_PORTS usage has changed few
times. It seems the most accurate to reference commit dropping
dsa_switch_alloc() in the Fixes tag.
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't true that CPU port is always the last one. Switches BCM5301x
have 9 ports (port 6 being inactive) and they use port 5 as CPU by
default (depending on design some other may be CPU ports too).
A more reliable way of determining number of ports is to check for the
last set bit in the "enabled_ports" bitfield.
This fixes b53 internal state, it will allow providing accurate info to
the DSA and is required to fix BCM5301x support.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 08cc83cc7f ("net: dsa: add support for BRIDGE_MROUTER
attribute") added an option for users to turn off multicast flooding
towards the CPU if they turn off the IGMP querier on a bridge which
already has enslaved ports (echo 0 > /sys/class/net/br0/bridge/multicast_router).
And commit a8b659e7ff ("net: dsa: act as passthrough for bridge port flags")
simply papered over that issue, because it moved the decision to flood
the CPU with multicast (or not) from the DSA core down to individual drivers,
instead of taking a more radical position then.
The truth is that disabling multicast flooding to the CPU is simply
something we are not prepared to do now, if at all. Some reasons:
- ICMP6 neighbor solicitation messages are unregistered multicast
packets as far as the bridge is concerned. So if we stop flooding
multicast, the outside world cannot ping the bridge device's IPv6
link-local address.
- There might be foreign interfaces bridged with our DSA switch ports
(sending a packet towards the host does not necessarily equal
termination, but maybe software forwarding). So if there is no one
interested in that multicast traffic in the local network stack, that
doesn't mean nobody is.
- PTP over L4 (IPv4, IPv6) is multicast, but is unregistered as far as
the bridge is concerned. This should reach the CPU port.
- The switch driver might not do FDB partitioning. And since we don't
even bother to do more fine-grained flood disabling (such as "disable
flooding _from_port_N_ towards the CPU port" as opposed to "disable
flooding _from_any_port_ towards the CPU port"), this breaks standalone
ports, or even multiple bridges where one has an IGMP querier and one
doesn't.
Reverting the logic makes all of the above work.
Fixes: a8b659e7ff ("net: dsa: act as passthrough for bridge port flags")
Fixes: 08cc83cc7f ("net: dsa: add support for BRIDGE_MROUTER attribute")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case CONFIG_VLAN_8021Q is not set, there will be no call down to the
b53 driver to ensure that the default PVID VLAN entry will be configured
with the appropriate untagged attribute towards the CPU port. We were
implicitly relying on dsa_slave_vlan_rx_add_vid() to do that for us,
instead make it explicit.
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer dev can never be null, the null check is redundant
and can be removed. Cleans up a static analysis warning that
pointer priv is dereferencing dev before dev is being null
checked.
Addresses-Coverity: ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ca89319483 ("net: dsa: b53: Keep CPU port as tagged in all
VLANs") forced the CPU port to be always tagged in any VLAN membership.
This was necessary back then because we did not support Broadcom tags
for all configurations so the only way to differentiate tagged and
untagged traffic while DSA_TAG_PROTO_NONE was used was to force the CPU
port into being always tagged.
With most configurations enabling Broadcom tags, especially after
8fab459e69 ("net: dsa: b53: Enable Broadcom tags for 531x5/539x
families") we do not need to apply this unconditional force tagging of
the CPU port in all VLANs.
A helper function is introduced to faciliate the encapsulation of the
specific condition requiring the CPU port to be tagged in all VLANs and
the dsa_switch_ops::untag_bridge_pvid boolean is moved to when
dsa_switch_ops::setup is called when we have already determined the
tagging protocol we will be using.
Reported-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree support to b53_mmap.c while keeping platform devices support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These tags are used on BCM5325, BCM5365 and BCM63xx switches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM63xx switches are present on bcm63xx and bmips devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing of_match_table to allow device tree probing.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having dynamic debug prints in b53_vlan_enable() has been helpful to
uncover a recent but update the function to indicate the port being
configured (or -1 for initial setup) and include the global VLAN enabled
and VLAN filtering enable status.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm_sf2 driver uses the b53 driver as a library but does not make
usre of the b53_setup() function, this made it fail to inherit the
vlan_filtering_is_global attribute. Fix this by moving the assignment to
b53_switch_alloc() which is used by bcm_sf2.
Fixes: 7228b23e68 ("net: dsa: b53: Let DSA handle mismatched VLAN filtering settings")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for being able to set the learning attribute on port, and
make sure that the standalone ports start up with learning disabled.
We can remove the code in bcm_sf2 that configured the ports learning
attribute because we want the standalone ports to have learning disabled
by default and port 7 cannot be bridged, so its learning attribute will
not change past its initial configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because bcm_sf2 implements its own dsa_switch_ops we need to export the
b53_br_flags_pre(), b53_br_flags() and b53_set_mrouter so we can wire-up
them up like they used to be with the former b53_br_egress_floods().
Fixes: a8b659e7ff ("net: dsa: act as passthrough for bridge port flags")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some drivers can't dynamically change the VLAN filtering option, or
impose some restrictions, it would be nice to propagate this info
through netlink instead of printing it to a kernel log that might never
be read. Also netlink extack includes the module that emitted the
message, which means that it's easier to figure out which ones are
driver-generated errors as opposed to command misuse.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to communicate their restrictions to user space directly,
instead of printing to the kernel log. Where the conversion would have
been lossy and things like VLAN ID could no longer be conveyed (due to
the lack of support for printf format specifier in netlink extack), I
chose to keep the messages in full form to the kernel log only, and
leave it up to individual driver maintainers to move more messages to
extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple ways in which a PORT_BRIDGE_FLAGS attribute can be
expressed by the bridge through switchdev, and not all of them can be
emulated by DSA mid-layer API at the same time.
One possible configuration is when the bridge offloads the port flags
using a mask that has a single bit set - therefore only one feature
should change. However, DSA currently groups together unicast and
multicast flooding in the .port_egress_floods method, which limits our
options when we try to add support for turning off broadcast flooding:
do we extend .port_egress_floods with a third parameter which b53 and
mv88e6xxx will ignore? But that means that the DSA layer, which
currently implements the PRE_BRIDGE_FLAGS attribute all by itself, will
see that .port_egress_floods is implemented, and will report that all 3
types of flooding are supported - not necessarily true.
Another configuration is when the user specifies more than one flag at
the same time, in the same netlink message. If we were to create one
individual function per offloadable bridge port flag, we would limit the
expressiveness of the switch driver of refusing certain combinations of
flag values. For example, a switch may not have an explicit knob for
flooding of unknown multicast, just for flooding in general. In that
case, the only correct thing to do is to allow changes to BR_FLOOD and
BR_MCAST_FLOOD in tandem, and never allow mismatched values. But having
a separate .port_set_unicast_flood and .port_set_multicast_flood would
not allow the driver to possibly reject that.
Also, DSA doesn't consider it necessary to inform the driver that a
SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute was offloaded, because it
just calls .port_egress_floods for the CPU port. When we'll add support
for the plain SWITCHDEV_ATTR_ID_PORT_MROUTER, that will become a real
problem because the flood settings will need to be held statefully in
the DSA middle layer, otherwise changing the mrouter port attribute will
impact the flooding attribute. And that's _assuming_ that the underlying
hardware doesn't have anything else to do when a multicast router
attaches to a port than flood unknown traffic to it. If it does, there
will need to be a dedicated .port_set_mrouter anyway.
So we need to let the DSA drivers see the exact form that the bridge
passes this switchdev attribute in, otherwise we are standing in the
way. Therefore we also need to use this form of language when
communicating to the driver that it needs to configure its initial
(before bridge join) and final (after bridge leave) port flags.
The b53 and mv88e6xxx drivers are converted to the passthrough API and
their implementation of .port_egress_floods is split into two: a
function that configures unicast flooding and another for multicast.
The mv88e6xxx implementation is quite hairy, and it turns out that
the implementations of unknown unicast flooding are actually the same
for 6185 and for 6352:
behind the confusing names actually lie two individual bits:
NO_UNKNOWN_MC -> FLOOD_UC = 0x4 = BIT(2)
NO_UNKNOWN_UC -> FLOOD_MC = 0x8 = BIT(3)
so there was no reason to entangle them in the first place.
Whereas the 6185 writes to MV88E6185_PORT_CTL0_FORWARD_UNKNOWN of
PORT_CTL0, which has the exact same bit index. I have left the
implementations separate though, for the only reason that the names are
different enough to confuse me, since I am not able to double-check with
a user manual. The multicast flooding setting for 6185 is in a different
register than for 6352 though.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The > comparison should be >= to prevent accessing one element beyond
the end of the dev->vlans[] array in the caller function, b53_vlan_add().
The "dev->vlans" array is allocated in the b53_switch_init() function
and it has "dev->num_vlans" elements.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/YAbxI97Dl/pmBy5V@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 54a0ed0df4 ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.
New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.
Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.
The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.
The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.
Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.
No behavior change except for the added prints is intended at this time.
$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[ 60.315148] br0: port 1(sw0p2) entered blocking state
[ 60.320350] br0: port 1(sw0p2) entered disabled state
[ 60.327839] device sw0p2 entered promiscuous mode
[ 60.334905] br0: port 1(sw0p2) entered blocking state
[ 60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It should be the driver's business to logically separate its VLAN
offloading into a preparation and a commit phase, and some drivers don't
need / can't do this.
So remove the transactional shim from DSA and let drivers propagate
errors directly from the .port_vlan_add callback.
It would appear that the code has worse error handling now than it had
before. DSA is the only in-kernel user of switchdev that offloads one
switchdev object to more than one port: for every VLAN object offloaded
to a user port, that VLAN is also offloaded to the CPU port. So the
"prepare for user port -> check for errors -> prepare for CPU port ->
check for errors -> commit for user port -> commit for CPU port"
sequence appears to make more sense than the one we are using now:
"offload to user port -> check for errors -> offload to CPU port ->
check for errors", but it is really a compromise. In the new way, we can
catch errors from the commit phase that we previously had to ignore.
But we have our hands tied and cannot do any rollback now: if we add a
VLAN on the CPU port and it fails, we can't do the rollback by simply
deleting it from the user port, because the switchdev API is not so nice
with us: it could have simply been there already, even with the same
flags. So we don't even attempt to rollback anything on addition error,
just leave whatever VLANs managed to get offloaded right where they are.
This should not be a problem at all in practice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For many drivers, the .port_mdb_prepare callback was not a good opportunity
to avoid any error condition, and they would suppress errors found during
the actual commit phase.
Where a logical separation between the prepare and the commit phase
existed, the function that used to implement the .port_mdb_prepare
callback still exists, but now it is called directly from .port_mdb_add,
which was modified to return an int code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Wallei <linus.walleij@linaro.org> # RTL8366
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The call path of a switchdev VLAN addition to the bridge looks something
like this today:
nbp_vlan_init
| __br_vlan_set_default_pvid
| | |
| | br_afspec |
| | | |
| | v |
| | br_process_vlan_info |
| | | |
| | v |
| | br_vlan_info |
| | / \ /
| | / \ /
| | / \ /
| | / \ /
v v v v v
nbp_vlan_add br_vlan_add ------+
| ^ ^ | |
| / | | |
| / / / |
\ br_vlan_get_master/ / v
\ ^ / / br_vlan_add_existing
\ | / / |
\ | / / /
\ | / / /
\ | / / /
\ | / / /
v | | v /
__vlan_add /
/ | /
/ | /
v | /
__vlan_vid_add | /
\ | /
v v v
br_switchdev_port_vlan_add
The ranges UAPI was introduced to the bridge in commit bdced7ef78
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.
Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328bb1 ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:
br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink
Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b935 ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.
In the meantime, commits such as 0944d6b5a2 ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.
Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c3d ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add
(the latter coming from commit 9c86ce2c1a ("net: bridge: Notify about
bridge VLANs")).
That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.
Let's go off and finish the job of commit 29ab586c3d by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60dc2
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).
Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.
And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.
Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM4908 family SoCs come with integrated Starfighter 2 switch. Its
registers layout it a mix of BCM7278 and BCM7445. It has 5 integrated
PHYs and 8 ports. It also supports RGMII and SerDes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210106213202.17459-3-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to the DSA receive path that we need to untage the bridge PVID,
this allows us to remove the dsa_untag_bridge_pvid() calls from
net/dsa/tag_brcm.c.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the B53 driver to support VLANs while not filtering. This
requires us to enable VLAN globally within the switch upon driver
initial configuration (dev->vlan_enabled).
We also need to remove the code that dealt with PVID re-configuration in
b53_vlan_filtering() since that function worked under the assumption
that it would only be called to make a bridge VLAN filtering, or not
filtering, and we would attempt to move the port's PVID accordingly.
Now that VLANs are programmed all the time, even in the case of a
non-VLAN filtering bridge, we would be programming a default_pvid for
the bridged switch ports.
We need the DSA receive path to pop the VLAN tag if it is the bridge's
default_pvid because the CPU port is always programmed tagged in the
programmed VLANs. In order to do so we utilize the
dsa_untag_bridge_pvid() helper introduced in the commit before within
net/dsa/tag_brcm.c.
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already maintain an array of VLANs used by the switch so we can
simply iterate over it to report the occupancy via devlink.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This allows us to differentiate between the possible failure modes of
b53_switch_reset() by looking at the dmesg output.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows us to see which device the err or info messages are
referring to if we have multiple b53 compatible devices on a board.
As this removes the only pr_*() calls in this file we can drop the
definition of pr_fmt().
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
