We already verify that offset and length are within the MTD device size
in the MTD API functions. Let's remove the duplicated checks in drivers.
This patch only affects the following API's:
'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'
This patch adds a bit of noise by removing too sparse empty lines, but this is
not too bad.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:
* bootloader cannot read the flash-based BBT format
* BBT is corrupted and the flash must be rescanned for bad
blocks; we want to remember bad blocks that were marked from Linux
So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.
The new flash-based BBT procedure for marking bad blocks:
(1) erase the affected block, to allow OOB marker to be written cleanly
(2) update in-memory BBT
(3) write bad block marker to OOB area of affected block
(4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.
This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.
Note that this is a change from the previous default flash-based BBT
behavior. If your system cannot support writing bad block markers to OOB,
use the new NAND_BBT_NO_OOB_BBM option (in combination with
NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Gcc complains here:
drivers/mtd/nand/docg4.c: In function ‘probe_docg4’:
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘resource_size_t’ [-Wformat]
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 4 has type ‘resource_size_t’ [-Wformat]
We have a standard way of printing these using a format string
extension.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This has been moved from .options to .bbt_options meanwhile. So, it
currently checks for something totally different (NAND_OWN_BUFFERS) and
decides according to that.
Artem Bityutskiy: the options were moved in
a40f734 mtd: nand: consolidate redundant flash-based BBT flags
Artem Bityutskiy: CCing -stable
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch renames all MTD functions by adding a "_" prefix:
mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a driver for the M-Sys / Sandisk diskonchip G4 nand flash found
in various smartphones and PDAs, among them the Palm Treo680, HTC Prophet and
Wizard, Toshiba Portege G900, Asus P526, and O2 XDA Zinc. It was tested on the
Treo 680, but should work generically.
Since v3, this patch adds power management functions, a scan of the factory bad
block table during initialization, several fixes, and more extensive testing.
Also, the platform data header file, which only contained partitioning
information, was removed. Command-line partitioning can be used, at least until
an mtd parser is written for the saftl format with which these chips are
shipped.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As nand_default_block_markbad() is becoming more complex, it helps to
have code appear only in its relevant codepath(s). Here, the calculation
of `ofs' based on NAND_BBT_SCANLASTPAGE is only useful on paths where we
write bad block markers to OOB. We move the condition/calculation closer
to the `write' operation and update the comment to more correctly
describe the operation.
The variable `wr_ofs' is also used to help isolate our calculation of
the "write" offset from the usage of `ofs' to represent the eraseblock
offset. This will become useful when we reorder operations in the next
patch.
This patch should make no functional change.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It seems that we have developed a bad-block-marking "feature" out of
pure laziness:
"We write two bytes per location, so we dont have to mess with 16 bit
access."
It's relatively simple to write a 1 byte at a time on x8 devices and 2
bytes at a time on x16 devices, so let's do it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
nand_block_bad() doesn't check the correct pages when
NAND_BBT_SCAN2NDPAGE is enabled. It should scan both the OOB region of
both the 1st and 2nd page of each block.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many NAND flash systems (especially those with MLC NAND) cannot be
reliably written twice in a row. For instance, when marking a bad block,
the block may already have data written to it, and so we should attempt
to erase the block before writing a bad block marker to its OOB region.
We can ignore erase failures, since the block may be bad such that it
cannot be erased properly; we still attempt to write zeros to its spare
area.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
CONFIG_GENERIC_IO is just enough for the basic MTD stuff.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This was part of the for-next branch earlier but for some reasons
a rebuild of the tree missed it, so I'm putting it back in now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Integrated Flash Controller(IFC) can be used to hook NAND Flash
chips using NAND Flash Machine available on it.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use a local copy of board informatin and fill with DT data.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
This will allow to enable it from the board.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
So we can now choose for the board the ecc mode (ecc soft, soft bch, no ecc
and hardware).
Set ecc mode in the boards to soft as currently in the driver.
Move platform data to a common header
include/linux/platform_data/atmel_nand.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: David Woodhouse <dwmw2@infradead.org>
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The main purpose of this patch is to fix several section mismatch
warnings from the board file and a few board specific drivers,
introduced with recent Amstrad Delta patch series, some of them rising
up only when building with CONFIG_MODULES not set.
While being at it, section tagging of all init data found in the board
file have been revised and hopefully corrected and/or optimized.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk8s6HsACgkQdwG7hYl686MIiACgxpNoUWFvq8z+2UGXxsLnNrio
hhcAn31H7TY3KUuIQBo4CqG2dEjNwpCw
=DRWp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.3' of git://git.infradead.org/~dwmw2/mtd-3.3
- Fix a regression in 16-bit Atmel NAND flash which was introduced in 3.1
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
* tag 'for-linus-3.3-20120204' of git://git.infradead.org/~dwmw2/mtd-3.3:
Revert "mtd: atmel_nand: optimize read/write buffer functions"
mtd: fix MTD suspend
jffs2: do not initialize variable unnecessarily
mtd: gpmi-nand bugfix: reset the BCH module when it is not MX23
mtd: nand: fix typo in comment
This reverts commit fb5427508a.
The reason is that it breaks 16 bits NAND flash as it was reported by
Nikolaus Voss and confirmed by Eric Bénard.
Nicolas Ferre <nicolas.ferre@atmel.com> alco confirmed:
"After double checking with designers, I must admit that I misunderstood
the way of optimizing accesses to SMC. 16 bit nand is not so common
those days..."
Reported-by: Nikolaus Voss <n.voss@weinmann.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.1+]
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In MX28, if we do not reset the BCH module. The BCH module may
becomes unstable when the board reboots for several thousands times.
This bug has been catched in customer's production.
The patch adds some comments (some from Wolfram Sang), and fixes it now.
Also change gpmi_reset_block() to static.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.1+]
Funny one :) "Heck" fits somehow, too, but I am sure it was meant to be "Check".
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk8Mq/MACgkQdwG7hYl686PeFACfZCgbdDWD9A/JL+i1RMfExVu6
Pi0An3Hmc3PTCp0yQ21KtcKhpF9CAMEu
=NfuL
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6
MTD pull for 3.3
* tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6: (113 commits)
mtd: Fix dependency for MTD_DOC200x
mtd: do not use mtd->block_markbad directly
logfs: do not use 'mtd->block_isbad' directly
mtd: introduce mtd_can_have_bb helper
mtd: do not use mtd->suspend and mtd->resume directly
mtd: do not use mtd->lock, unlock and is_locked directly
mtd: do not use mtd->sync directly
mtd: harmonize mtd_writev usage
mtd: do not use mtd->lock_user_prot_reg directly
mtd: mtd->write_user_prot_reg directly
mtd: do not use mtd->read_*_prot_reg directly
mtd: do not use mtd->get_*_prot_info directly
mtd: do not use mtd->read_oob directly
mtd: mtdoops: do not use mtd->panic_write directly
romfs: do not use mtd->get_unmapped_area directly
mtd: do not use mtd->get_unmapped_area directly
mtd: do use mtd->point directly
mtd: introduce mtd_has_oob helper
mtd: mtdcore: export symbols cleanup
mtd: clean-up the default_mtd_writev function
...
Fix up trivial edit/remove conflict in drivers/staging/spectra/lld_mtd.c
Another simple series related to clock management, this time only for
imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=czKE
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9 ("net/fec: fix the .remove code").
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
I ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9q+1
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Cleanups on various subarchitectures
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
Arnd ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
arm/at91: fix build of stamp9g20
ARM: u300: delete memory.h
MAINTAINERS: add maintainer entry for Picochip picoxcell
ARM: picoxcell: move io mappings to common.c
ARM: picoxcell: don't reserve irq_descs
ARM: picoxcell: remove mach/memory.h
ARM: at91: delete the pcontrol_g20_defconfig
arm/tegra: Remove code that's ifndef CONFIG_ARM_GIC
arm/tegra: remove unused defines
arm/tegra: fix variable formatting in makefile
ARM: davinci: vpif: move code to driver core header from platform
ARM: at91/gpio: fix display of number of irq setuped
ARM: at91/gpio: drop PIN_BASE
ARM: at91/udc: use gpio_is_valid to check the gpio
ARM: at91/ohci: use gpio_is_valid to check the gpio
ARM: at91/nand: use gpio_is_valid to check the gpio
ARM: at91/mmc: use gpio_is_valid to check the gpio
ARM: at91/ide: use gpio_is_valid to check the gpio
ARM: at91/pata: use gpio_is_valid to check the gpio
ARM: at91/soc: use gpio_is_valid to check the gpio
...
Reimplement a call to devm_request_mem_region followed by a call to ioremap
or ioremap_nocache by a call to devm_request_and_ioremap.
The semantic patch that makes this transformation is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\))) {
- ...
- return ...;
-}
... when != res->start
(
-devm_ioremap(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
|
-devm_ioremap_nocache(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
)
... when any
when != res->start
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add device tree bindings so that the gpio-nand driver may be
instantiated from the device tree. This also allows the partitions
to be specified in the device tree.
v7: - restore runtime device tree/non device tree detection
v6: - convert to mtd_device_parse_register()
v5: - fold dt config helpers into a single gpio_nand_of_get_config()
v4: - get io sync address from gpio-control-nand,io-sync-reg
property rather than a resource
- clarified a few details in the binding
v3: - remove redundant cast and a couple of whitespace/naming
changes
v2: - add CONFIG_OF guards for non-dt platforms
- compatible becomes gpio-control-nand
- clarify some binding details
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There was a bug for fmr initialization, which lead to fmr was always 0x100
in fsl_elbc_chip_init() and caused FCM command timeout before calling
fsl_elbc_chip_init_tail(), now we initialize CWTO to maximum timeout value
and not relying on the setting of bootloader.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If we use the Nand flash chip whose number of pages in a block is greater
than 64(for large page), we must treat the low bit of FBAR as being the
high bit of the page address due to the limitation of FCM, it simply uses
the low 6-bits (for large page) of the combined block/page address as the
FPAR component, rather than considering the actual block size.
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When we do a non-full-page write, the length be set to FBCR should
not be 'elbc_fcm_ctrl->index', it should be 'elbc_fcm_ctrl->index -
elbc_fcm_ctrl->column'.
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On both of large-page chip and small-page chip, we always should use
'elbc_fcm_ctrl->oob' to set the FPAR_LP_MS/FPAR_SP_MS bit of FPAR, don't
use a overflowed 'column' to set it.
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch converts the drivers in drivers/mtd/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Making MTD_NAND_OMAP2 depend on ARCH_OMAP2PLUS instead of
oring with ARCH2/3/4.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Macronix MX30LF1208AA is a 512 Mbit NAND with device code 0xF0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Macronix is produing SLC NAND MX30LF1208AA, so add their manufacturer
code to the manufacturer lists.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes usage of dma direction to adopt dma_transfer_direction.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Don't use Amstrad Delta custom I/O functions for controlling the device,
use GPIO API instead.
While being at it, add missing gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes:
drivers/mtd/nand/gpmi-nand/gpmi-nand.c: In function 'gpmi_nfc_init':
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/nand/gpmi-nand/gpmi-nand.c: At top level:
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:15: error: expected declaration specifiers or '...' before string constant
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: data definition has no type or storage class
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
and some more...
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In commit 9d7948c500 (mtd: ndfc: use
ofpart through generic parsing) we dereference a non pointer type
causing the following compiler error:
drivers/mtd/nand/ndfc.c: In function 'ndfc_chip_init':
drivers/mtd/nand/ndfc.c:191: error: invalid type argument of '->' (have 'struct mtd_part_parser_data')
Fix that.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This converts the remaining USB drivers in the kernel to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Till Harbaum <till@harbaum.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MTD_PARTITIONS got killed in commit 6a8a98b22b. This means that since
v3.0 this Kconfig symbol doesn't exist anymore. Apparently selecting
a non-existant symbol is a nop. Drop that select.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
We are cleaning up the implicit presence of module.h that these
drivers are taking advantage of. Fix them in advance of the
cleanup operation.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These two common macros will be no longer present everywhere.
Call out the include needs of them explicitly where required.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Our `ops' information was converted to a local variable recently, and
apparently, old code relied on the fact that the global version was
often left in a valid mode. We can't make this assumption on local
structs, and we shouldn't be relying on a previous state anyway.
Instead, we initialize mode to 0 for don't-care situations (i.e., the
operation does not use OOB anyway) and MTD_OPS_PLACE_OOB when we want to
place OOB data.
This fixes a bug with nand_default_block_markbad(), where we catch on
the BUG() call in nand_fill_oob():
Kernel bug detected[#1]:
...
Call Trace:
[<80307350>] nand_fill_oob.clone.5+0xa4/0x15c
[<803075d8>] nand_do_write_oob+0x1d0/0x260
[<803077c4>] nand_default_block_markbad+0x15c/0x1a8
[<802e8c2c>] part_block_markbad+0x80/0x98
[<802ebc74>] mtd_ioctl+0x6d8/0xbd0
[<802ec1a4>] mtd_unlocked_ioctl+0x38/0x5c
[<800d9c60>] do_vfs_ioctl+0xa4/0x6e4
[<800da2e4>] sys_ioctl+0x44/0xa0
[<8001381c>] stack_done+0x20/0x40
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This driver has been broken through all of git history and
cannot even be built. Better mark it as broken. Next stop is
removing from the tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
It is not used outside this driver so no need to make the symbol global.
Also make r852_suspend and r852_resume static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
For NFC v1, the unlock end block address was 0x4000, which would only
unlock the first 32 blocks of the NAND flash. Change that value to
0xffff to unlock all available blocks, as is done for NFC v21 as well.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
A portion of the `check_pattern()' function is basically a `memcmp()'.
Since it's possible for `memcmp()' to be optimized for a particular
architecture, we should use it instead.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
In rare cases, we are given an unaligned parameter `from' in
`nand_do_read_ops()'. In such cases, we use the page cache
(chip->buffers->databuf) as an intermediate buffer before dumping to the
client buffer. However, there are also cases where this buffer is not
cleanly reusable. In those cases, we need to make sure that we
explicitly invalidate the cache.
This patch prevents accidental reusage of the page cache, and for me,
this solves some problems I come across when reading a corrupted BBT
from flash (NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).
Note: the rare "unaligned" case is a result of the extra BBT pattern +
version located in the data area instead of OOB.
Also, this patch disables caching on raw reads, since we are reading
without error correction. This is, obviously, prone to errors and should
not be cached.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Updates to our default function for creating bad block patterns have
broken the "no OOB" feature. The NAND_BBT_NO_OOB option should not be
set while scanning for bad blocks, but we've been passing all BBT
options from nand_chip.bbt_options to the bad block scan. This causes us
to hit the:
BUG_ON(bd->options & NAND_BBT_NO_OOB);
in create_bbt() when we scan the flash for bad blocks.
Thus, while it can be legal to set NAND_BBT_NO_OOB in a custom badblock
pattern descriptor (presumably with NAND_BBT_CREATE disabled?), we
should not pass it through in our default function.
Also, to help clarify and emphasize that the function creates bad block
patterns only (not, for example, table descriptors for locating
flash-based BBT), I renamed `nand_create_default_bbt_descr' to
`nand_create_badblock_pattern'.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Because there are so many cases of checking, writing, and re-writing of
the bad block table(s), we might as well wait until the we've settled on
a valid, clean copy of the table. This also prevents us from falsely
incrementing the table version. For example, we may have the following:
Primary table, with version 0x02
Mirror table, with version 0x01
Primary table has uncorrectable ECC errors
If we don't have this fix applied, then we will:
Choose to read the primary table (higher version)
Set mirror table version to 0x02
Read back primary table
Invalidate table because of ECC errors
Retry readback operation with mirror table, now version 0x02
Mirrored table reads cleanly
Writeback BBT to primary table location (with "version 0x02")
However, the mirrored table shouldn't have a new version number.
Instead, we actually want:
Choose to read the primary table (higher version)
Read back primary table
Invalidate table because of ECC errors
Retry readback with mirror table (version 0x01)
Mirrored table reads cleanly
Set both tables to version 0x01
Writeback BBT to primary table location (version 0x01)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Now that `read_bbt()' returns ECC error codes properly, we handle those
codes when checking the integrity of our flash-based BBT.
The modifications can be described by this new policy:
*) On any uncorrected ECC error, we invalidate the corresponding table
and retry our version-checking integrity logic.
*) On corrected bitflips, we mark both tables for re-writing to flash
(a.k.a. scrubbing).
Current integrity checks (i.e., comparing version numbers, etc.) should
take care of all the cases that result in rescanning the device for bad
blocks or falling back to the BBT as found in the mirror descriptor.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Instead of just printing a warning when encountering ECC errors, we
should return a proper error status and print a more informative
warning. Later, we will handle these error messages in the upper layers
of the BBT scan.
Note that this patch makes our check for ECC error codes a little bit
more restrictive, leaving all unrecognized errors to the generic "else"
clause. This shouldn't cause problems and could even be a benefit.
This code is based on some findings reported by Matthieu Castet.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This is a second step in restructuring `check_create()'. When we don't
rely on goto statements for our main functionality, the code will become
a little easier to manipulate.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
We will begin restructuring the code for check_create so that we can
make some important changes. For now, we should just begin to get rid of
some goto statements to make things cleaner. This is the first step of a
few, which are separated to make them easier to follow.
This step should just be a code refactor.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Remove some extra spaces
Consistently use '0x' prefix for bitfield-like constants
Spelling: "aplies" -> "applies"
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
`writeops' is unnecessary in the function `nand_update_bbt()'
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
There are a few reasons not to ignore ECC errors here.
First, mtd->read_oob is being called in raw mode, so there should be no
error correction in the first place.
Second, if we change this such that there *is* error correction in this
function, then we will want to pass the error message upward.
In fact, the code I introduced to "ignore ECC errors" would have been
better if it had just placed this test down in `scan_block_full()' in
the first place. We would like to ignore ECC errors when we are simply
checking for bad block markers (e.g., factory marked), but we may not
want to ignore ECC errors when scanning OOB for a flash-based BBT
pattern (in `scan_read_raw()'; note that the return codes from
`scan_read_raw()' are not actually handled yet).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
A few pieces of code are unnecessarily duplicated. For easier
maintenance, we should fix this.
This should have no functional effect.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
The nand_chip.ops field is a struct that is passed around globally with
no particular reason. Every time it is used, it could just as easily be
replaced with a local struct that is updated on each operation. So make
it local.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
These modes are not necessarily for OOB only. Particularly, MTD_OOB_RAW
affected operations on in-band page data as well. To clarify these
options and to emphasize that their effect is applied per-operation, we
change the primary prefix to MTD_OPS_.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This fixes issues with `nanddump -n' and the MEMREADOOB[64] ioctls on
hardware that performs error correction when reading only OOB data. A
driver for such hardware needs to know when we're doing a RAW vs. a
normal write, but mtd_do_read_oob does not pass such information to the
lower layers (e.g., NAND). We should pass MTD_OOB_RAW or MTD_OOB_PLACE
based on the MTD file mode.
For now, most drivers can get away with just setting:
chip->ecc.read_oob_raw = chip->ecc.read_oob
This is done by default; but for systems that behave as described above,
you must supply your own replacement function.
This was tested with nandsim as well as on actual SLC NAND.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This fixes issues with `nandwrite -n -o' and the MEMWRITEOOB[64] ioctls
on hardware that writes ECC when writing OOB. The problem arises as
follows: `nandwrite -n' can write page data to flash without applying
ECC, but when used with the `-o' option, ECC is applied (incorrectly),
contrary to the `--noecc' option.
I found that this is the case because my hardware computes and writes
ECC data to flash upon either OOB write or page write. Thus, to support
a proper "no ECC" write, my driver must know when we're performing a raw
OOB write vs. a normal ECC OOB write. However, MTD does not pass any raw
mode information to the write_oob functions. This patch addresses the
problems by:
1) Passing MTD_OOB_RAW down to lower layers, instead of just defaulting
to MTD_OOB_PLACE
2) Handling MTD_OOB_RAW within the NAND layer's `nand_do_write_oob'
3) Adding a new (replaceable) function pointer in struct ecc_ctrl; this
function should support writing OOB without ECC data. Current
hardware often can use the same OOB write function when writing
either with or without ECC
This was tested with nandsim as well as on actual SLC NAND.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
These files contain the common code for the GPMI-NAND driver.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Koen Beel <koen.beel@barco.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
add the GPMI-NAND driver in the relevant Kconfig and Makefile in the MTD.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Koen Beel <koen.beel@barco.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This has already been tested with Samsung NAND: K9LAG08U0M
on MX53EVK board, ubi/ubifs has already been tested OK too.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Convert error handling code to use gotos. At the same time, this adds
calls to kfree and iounmap in a few cases where they were overlooked.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
clk_get() return a pointer to the struct clk or an ERR_PTR().
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
use MTD_NAND_OMAP2 also for OMAP4 arch.
testes with omap4430
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Start moving away from the MTD_DEBUG_LEVEL messages. The dynamic
debugging feature is a generic kernel feature that provides more
flexibility.
(See Documentation/dynamic-debug-howto.txt)
Also fix some punctuation, indentation, and capitalization that went
along with the affected lines.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This is a cleanup of some punctuation, indentation, and capitalization
on the lines affected affected by the last patch.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Instead of directly calling printk, it's simpler to use the built-in
pr_* functions. This shortens code and allows easy customization through
the definition of a pr_fmt() macro (not used currently). Ideally, we
could implement much of this with dev_* functions, but the MTD subsystem
does not necessarily register all its master `mtd_info.dev` device, so
we cannot use dev_* consistently. See:
http://lists.infradead.org/pipermail/linux-mtd/2011-July/036950.html
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Soon we will change many printk statements into pr_* statements, i.e.,
'printk(KERN_INFO, ...)' becomes 'pr_info(...)'. However, this means that
KERN_DEBUG messages will become pr_debug() statements and therefore will
not be activated by default - they must be enabled using dynamic debug.
So, for important DEBUG messages, we will simply upgrade these to INFO
so that they appear by default.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Current pxa3xx_nand controller has two chip select which
both be workable. This patch enable this feature.
Update platform driver to support this feature.
Another notice should be taken that:
When you want to use this feature, you should not enable the
keep configuration feature, for two chip select could be
attached with different nand chip. The different page size
and timing requirement make the keep configuration impossible.
Signed-off-by: Lei Wen <leiwen@marvell.com>
This patch add protection on the suspend&resume path to prevent
some unexpected behavior, like interrupt occur at the very second
of resume back and it don't follow normal command path, which lead
to bug.
Signed-off-by: Lei Wen <leiwen@marvell.com>
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly. Remove this useless (and potentially problematic)
block of code.
Signed-off-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
For PIO NAND access functions, we use the features of the SMC:
- no need to take into account the NAND bus width: SMC will deal with this
- use of an IO memcpy on the NAND chip-select space is able to generate
proper SMC behavior.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
The global data fsl_lbc_ctrl_dev->nand don't have to be freed in
fsl_elbc_chip_remove(). The right place to do that is in fsl_elbc_nand_remove()
if elbc_fcm_ctrl->counter is zero.
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
there is a bug in nand_flash_detect_onfi, busw need to be passed
by pointer to return it.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Now that nand_do_readoob() may return -EUCLEAN or -EBADMSG on ECC errors,
we need to handle the return value specially in some cases.
When scanning for simple bad block markers, reacting to an ECC error is
not very useful, as we assume that the relevant markers are still
non-0xFF for true bad blocks.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
While the standard NAND OOB functions do not do ECC on the spare area,
it is possible for a driver to supply its own OOB ECC functions (e.g., HW
ECC). nand_do_read_oob should act like nand_do_read_ops in checking the
ECC stats and returning -EBADMSG or -EUCLEAN on uncorrectable errors or
correctable bitflips, respectively. These error codes could be used in
flash-based BBT code or in YAFFS, for example.
Doing this, however, messes with the behavior of mtd_do_readoob. Now,
mtd_do_readoob should check whether we had -EUCLEAN or -EBADMSG errors
and discard those as "non-fatal" so that the ioctls can still succeed
with (possibly uncorrected) data.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
EDB7312 isn't supported by mainline kernel, so drop it now.
If the board support will ever be submitted to mainline,
one can revert this commit.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
In nand_do_write_ops() code it is possible for a caller to provide
ops.oobbuf populated and ops.mode == MTD_OOB_AUTO, which currently
means that the chip->oob_poi buffer isn't initialised to all 0xFF.
The nand_fill_oob() method then carries out the task of copying
the provided OOB data to oob_poi, but with MTD_OOB_AUTO it skips
areas marked as unavailable by the layout struct, including the
bad block marker bytes.
An example of this causing issues is when the last OOB data read
was from the start of a bad block where the markers are not 0xFF,
and the caller wishes to write new OOB data at the beginning of
another block. In this scenario the caller would provide OOB data,
but nand_fill_oob() would skip the bad block marker bytes in
oob_poi before copying the OOB data provided by the caller.
This means that when the OOB data is written back to NAND,
the block is inadvertently marked as bad without the caller knowing.
This has been witnessed when using YAFFS2 where tags are stored
in the OOB.
To avoid this oob_poi is always initialised to 0xFF to make sure
no left over data is inadvertently written back to the OOB area.
Credits to Brian Norris <computersforpeace@gmail.com> for fixing this
patch.
Signed-off-by: Adam Thomson <adam.thomson@alcatel-lucent.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Cc: stable@kernel.org [2.6.20+]
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Linus Walleij: fixed compilation breakage
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Artem: tewaked the patch
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Artem: tweaked the patch
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Fixed by Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
mtd_device_unregister is done in nand_release(),
thus no need to call it in nand_davinci_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When a memory allocation fails, the kernel will print out a backtrace
automatically. These print statements are unnecessary.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This bug was introduced in f8155a40 ("mtd: pxa3xx_nand: rework irq
logic") and causes the PXA3xx NAND controller fail to operate with NAND
flash that has empty pages. According to the comment in this block, the
hardware controller will report a double-bit error for empty pages,
which can and must be ignored.
This patch restores the original behaviour of the driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lei Wen <leiwen@marvell.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When keep_config is set, the detection would goes different routine.
That the driver would read out the setting which is set previously
by bootloader. While most bootloader keep the irq mask as off, and
current driver need all irq default open, keep_config behavior would
lead to no irq at all.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Commit c89eeda810 (mtd: denali: detect the
number of banks) introduced runtime detection of the number of banks.
However, denali_nand_reset() uses uses denanli_nand_info::max_banks so
we need to detect the maximum number of banks before doing the reset.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Drop now unused set_parts from struct platform_nand_data. Also, while we are
at it, drop long unused priv field from platform_nand_data.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Artem: while on it, do other commentaries clean-ups:
1. Start one-line comments with capital letter and no dot at the end
2. Turn sparse multi-line comments into one-line comments
3. Change "phrase ?" to "phrase?" and the same with "!".
4. Remove tabs from the kerneldoc parameters comments - they are mixed
with tabs often, and inconsistent.
5. Put dot at the end of descriptions in kerneldoc comments.
6. Some other small commentaries clean-ups
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Artem: tweaked the patch
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Artem: tweaked the patch
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Artem: tweaked the patch
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Remove unused variable 'mtd' to eliminate below warning.
CC drivers/mtd/nand/pxa3xx_nand.o
drivers/mtd/nand/pxa3xx_nand.c: In function 'pxa3xx_nand_suspend':
drivers/mtd/nand/pxa3xx_nand.c:1167: warning: unused variable 'mtd'
drivers/mtd/nand/pxa3xx_nand.c: In function 'pxa3xx_nand_resume':
drivers/mtd/nand/pxa3xx_nand.c:1180: warning: unused variable 'mtd'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In fsmc_nand_remove, we should call nand_release instead of
mtd_device_unregister to properly free bad block table memory
and bad block descriptor memory.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In pxa3xx_nand_remove, we should call nand_release instead of
mtd_device_unregister to properly free bad block table memory
and bad block descriptor memory.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The implementation of nand_release() already call mtd_device_unregister(),
no need to call it again.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I believe this TODO was unnecessary back when it was introduced:
commit d1e1f4e42b
mtd: nand: add support for reading ONFI parameters...
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
There is no need to guard mtd->name with CONFIG_MTD_CMDLINE_PARTS
as name can be used by other parts.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This delay is meaningless. If delay is needed it is device specific
and must be reimplemented by specific driver, otherwise no delay is
needed.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Acked-by: Vimal Singh <vimal.newwork@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Currently atmel_nand driver used by AT91 and AVR32 calls a special callback
which return nand partition table and number of partitions. However in all
boards this callback returns just static data. So drop this callback and
make atmel_nand use partition table provided statically via platform_data.
Nicolas Ferre: I am in favor for a mainline inclusion through linux-mtd tree.
Hans-Christian Egtvedt: I'm fine by sending the changes for AVR32 through linux-mtd
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
According to our new prefix rules, we should rename NAND_CREATE_EMPTY_BBT
with a NAND_BBT prefix, i.e., NAND_BBT_CREATE_EMPTY.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The NAND_CREATE_EMPTY_BBT flag was added by commit:
453281a973
mtd: nand: introduce NAND_CREATE_EMPTY_BBT
This flag is not used within the kernel and not explained well, so I
took the liberty to edit its comments.
Also, this is a BBT-related flag (and closely tied with NAND_BBT_CREATE)
so I'm moving it to bbm.h next to NAND_BBT_CREATE, thus requiring that
we use the flag in nand_chip.bbt_options, *not* in nand_chip.options.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Recall the recently added prefix requirements:
* "NAND_" for flags in nand.h, used in nand_chip.options
* "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options
or in nand_bbt_descr.options
Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH.
Again, this flag is found in bbm.h and so should NOT be used in the
"nand_chip.options" field.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch works with the following three flags from two headers (nand.h
and bbm.h):
(1) NAND_USE_FLASH_BBT (nand.h)
(2) NAND_USE_FLASH_BBT_NO_OOB (nand.h)
(3) NAND_BBT_NO_OOB (bbm.h)
These flags are all related and interdependent, yet they were in
different headers. Flag (2) is simply the combination of (1) and (3) and
can be eliminated.
This patch accomplishes the following:
* eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2))
* move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h
It's important to note that because (1) and (3) are now both found in
bbm.h, they should NOT be used in the "nand_chip.options" field.
I removed a small section from the mtdnand DocBook because it referes to
NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch handles the problems we've been having with using conflicting
flags from nand.h and bbm.h in the same nand_chip.options field. We
should try to separate these two spaces a little more clearly, and so I
have added a bbt_options field to nand_chip.
Important notes about nand_chip fields:
* bbt_options field should contain ONLY flags from bbm.h. They should be
able to pass safely to a nand_bbt_descr data structure.
- BBT option flags start with the "NAND_BBT_" prefix.
* options field should contian ONLY flags from nand.h. Ideally, they
should not be involved in any BBT related options.
- NAND chip option flags start with the "NAND_" prefix.
* Every flag should have a nice comment explaining what the flag is. While
this is not yet the case on all existing flags, please be sure to write
one for new flags. Even better, you can help document the code better
yourself!
Please try to follow these conventions to make everyone's lives easier.
Among the flags that are being moved to the new bbt_options field
throughout various drivers, etc. are:
* NAND_BBT_SCANLASTPAGE
* NAND_BBT_SCAN2NDPAGE
and there will be more to come.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch reverts most of:
commit 58373ff0af
mtd: nand: more BB Detection refactoring and dynamic scan options
According to the discussion at:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035696.html
the NAND_BBT_SCANBYTE1AND6 flag, although technically valid, can break
some existing ECC layouts that use the 6th byte in the OOB for ECC data.
Furthermore, we apparently do not need to scan both bytes 1 and 6 in
the OOB region of the devices under consideration; instead, we only need
to scan one or the other.
Thus, the NAND_BBT_SCANBYTE1AND6 flag is at best unnecessary and at
worst a regression.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
when nand_get_flash_type() is called, it will read 8 bytes of ID instead of 5,
but the driver only read 5 bytes, so kernel will dump error messages like:
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
With the addition of the platform device mfd_cell pointer, we can now
cleanly pass the sub device drivers platform data pointers through the
regular device platform_data one, and get rid of mfd_get_data().
Cc: Ian Molton <spyro@f2s.com>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that none of the drivers use CONFIG_MTD_PARTITIONS we can remove
it from Kconfig and the last remaining uses.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The older add_mtd_device()/add_mtd_partitions() and their removal
counterparts will soon be gone. Replace uses with mtd_device_register()
and mtd_device_unregister().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the check for
mtd_has_partitions() as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Cc: Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When reading/writing a subpage (When HW ECC is not available/enabled)
for number of bytes not aligned to 4, the mis-aligned bytes are handled
first (by cpu copy method) before enabling the Prefetch engine to/from
'p'(start of buffer 'buf'). Then it reads/writes rest of the bytes with
the help of Prefetch engine, if available, or again using cpu copy method.
Currently, reading/writing of rest of bytes, is not done correctly since
its trying to read/write again to/from begining of buffer 'buf',
overwriting the mis-aligned bytes.
Read & write using prefetch engine got broken in commit '2c01946c'.
We never hit a scenario of not getting 'gpmc_prefetch_enable' call
success. So, problem did not get caught up.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Vimal Singh <vimal.newwork@gmail.com>
Reported-by: Bryan DE FARIA <bdefaria@adeneo-embedded.com>
Cc: stable@kernel.org [2.6.35+]
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Not all configurations of the Denali controller support 4 banks. The
controller can support between 1 and 16 banks. Detect this from the
design features register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The controller has interrupt enable/status register pairs for each bank
(along with ECC and status registers) that differ only in address offset.
Rather than providing definitions for each register, make the address a
macro so that it scales for devices with different numbers of banks.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Rather than using the PCI specific DMA API, convert to the generic
DMA API so that we can use the Denali NAND controller on other bus
types.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In commit c7b28e25cb the initialization of
the backblockbits was accidentally removed. This patch returns it back,
because otherwise some NAND drivers are broken.
This problem was reported by "Saxena, Parth <parth.saxena@ti.com>" here:
http://lists.infradead.org/pipermail/linux-mtd/2011-April/035221.html
Reported-by: Saxena, Parth <parth.saxena@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Tested-by: Saxena, Parth <parth.saxena@ti.com>
Acked-by: Saxena, Parth <parth.saxena@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Cc: stable@kernel.org [2.6.36+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch extends NDFC driver to support all 4 chip selects
available in NDFC NAND controller. Tested on custom 460EX board
with 2 chip select NAND device.
Artem: white-space cleanups
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
nand_scan calls nand_scan_tail and here we got a ecc.layout and calculate
oobavail for this layout. After calling nand_scan, we change the layout pointer
if OMAP_ECC_HAMMING_CODE_HW_ROMCODE is set. This results in not calcluated
oobavail. Mountig as jffs2 is not possible.
To fix that nand_scan has to split up in nand_scan_ident and nand_scan_tail
setting ecc.layout between these calls. So nand_scan_tail calculates oobvail
for the used layout. This is also done in serveral other platforms.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Reviewed-by: Vimal Singh <vimal.newwork@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Including linux/dmaengine.h fixes the missing definition of the enum
dma_ctrl_flags type used in atmel_nand_dma_op function.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Chip deselection is already done in nand_release_device. So only
duplicate code.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Current implementation of s3c2410_nand_select_chip call
clk_disable every time when chip = -1 (de-select). This happend
multiple times even if chip was already de-selected. This causes
disabling clock even if they are already disabled and due to
nature of clock subsytem implementation this causes nand clock
to be disabled and newer enabled again.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It is nicer to dynamically create our badblock patterns than to
statically define them. The nand_create_default_bbt_descr() function
does a sufficient job of handling various bad block scanning options
for either flash-based or non-flash-based BBTs, so we might as well
use the function for both cases.
This patch simplifies and shortens our code (and removes a TODO that
I left a few months ago).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Do the following to add support for up to 4 chips on V21 devices (i.MX25 and
i.MX35):
* implement .select_chip for V21
* adjust existing NFC_V1_V2_BUF_ADDR writes to take chip select into account
* unlock all chip selects at preset_v1_v2()
* scan up to 4 devices at .probe
This has been tested on i.MX25 with two attached NAND chip (on one die).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.
This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115bb6
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
* git://git.infradead.org/mtd-2.6:
mtd: atmel_nand: use CPU I/O when buffer is in vmalloc(ed) region
mtd: atmel_nand: modify test case for using DMA operations
mtd: atmel_nand: fix support for CPUs that do not support DMA access
mtd: atmel_nand: trivial: change DMA usage information trace
mtd: mtdswap: fix printk format warning
The previous way of dealing with vmalloc(ed) region by walking
though the pages can not work well actually. We just fall back
to CPU I/O when the buffer address is higher than `high_memory'.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We have better performances not using DMA for oob operations.
Modify size test so that it is using DMA for size greater than oobsize.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
use_dma was always "1" even if the CPU does not support DMA
Tested on AT91SAM9261EK by Jean-Christophe PLAGNIOL-VILLARD
Reported-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6: (9356 commits)
[media] rc: update for bitop name changes
fs: simplify iget & friends
fs: pull inode->i_lock up out of writeback_single_inode
fs: rename inode_lock to inode_hash_lock
fs: move i_wb_list out from under inode_lock
fs: move i_sb_list out from under inode_lock
fs: remove inode_lock from iput_final and prune_icache
fs: Lock the inode LRU list separately
fs: factor inode disposal
fs: protect inode->i_state with inode->i_lock
lib, arch: add filter argument to show_mem and fix private implementations
SLUB: Write to per cpu data when allocating it
slub: Fix debugobjects with lockless fastpath
autofs4: Do not potentially dereference NULL pointer returned by fget() in autofs_dev_ioctl_setpipefd()
autofs4 - remove autofs4_lock
autofs4 - fix d_manage() return on rcu-walk
autofs4 - fix autofs4_expire_indirect() traversal
autofs4 - fix dentry leak in autofs4_expire_direct()
autofs4 - reinstate last used update on access
vfs - check non-mountpoint dentry might block in __follow_mount_rcu()
...
NOTE!
This merge commit was created to fix compilation error. The block
tree was merged upstream and removed the 'elv_queue_empty()'
function which the new 'mtdswap' driver is using. So a simple
merge of the mtd tree with upstream does not compile. And the
mtd tree has already be published, so re-basing it is not an option.
To fix this unfortunate situation, I had to merge upstream into the
mtd-2.6.git tree without committing, put the fixup patch on top of
this, and then commit this. The result is that we do not have commits
which do not compile.
In other words, this merge commit "merges" 3 things: the MTD tree, the
upstream tree, and the fixup patch.
This silences warnings such as
drivers/video/tmiofb.c: In function 'tmiofb_hw_init':
drivers/video/tmiofb.c:270: warning: initialization discards qualifiers from pointer target type
These were added by me in commit 2a79bb1d.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use mfd_data for passing information from mfd drivers to mfd
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data(). This changes tmio-nand only; mfd drivers with
other cells are not modified.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* git://git.infradead.org/users/dwmw2/mtd-2.6.38:
mtd: add "platform:" prefix for platform modalias
mtd: mtd_blkdevs: fix double free on error path
mtd: amd76xrom: fix oops at boot when resources are not available
mtd: fix race in cfi_cmdset_0001 driver
mtd: jedec_probe: initialise make sector erase command variable
mtd: jedec_probe: Change variable name from cfi_p to cfi
This patch adds option 'bch' to nandsim, which can be used to enable
software BCH ECC (introduced in previous patches) and select BCH error
correction capability.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds software BCH ECC support to mtd, in order to handle recent
NAND device ecc requirements (4 bits or more).
It does so by adding a new ecc mode (NAND_ECC_SOFT_BCH) for use by board
drivers, and a new Kconfig option to enable BCH support. It relies on the
generic BCH library introduced in a previous patch.
When a board driver uses mode NAND_ECC_SOFT_BCH, it should also set fields
chip->ecc.size and chip->ecc.bytes to select BCH ecc data size and required
error correction capability. See nand_bch_init() documentation for details.
It has been tested on the following platforms using mtd-utils, UBI and
UBIFS: x86 (with nandsim), arm926ejs.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When page size is 4KiB, ecc.total is set to 8*9, and this causes
nand_write_page_hwecc() to read past the initialized part of the eccpos array,
which corrupts chip->oob_poi with bogus values from ecc_calc.
Fix this by creating a proper nand_ecclayout for 4KiB flashes.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The DaVinci NAND driver was including the mach-types.h header
file.
This prevented the DaVinci NAND driver from getting used
in a DSP only device. The linux port on c6x devices can make
use of the same driver and does not define a corresponding
header file.
This header file was required in the driver because earlier there was code
dependent on a machine_* check. This piece of code has now been factored out
and is in arch/arm/mach-davinci/aemif.c
Thus removing the header file is harmless
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use nand_scan_ident to unify the need of mtd member initilization
for both normal detection and keep configuration method.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Different NAND driver may require its unique detection. For pxa3xx_nand,
it use its self id database to get the necessary info.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make the interface simpler which could make both debug
and enhancement easier.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since we have rework the irq process, we don't need additional
delay in wait_for_event. Also write_cmd and __readid is also
discarded for the same reason.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Enable all irq when we start the nand controller, and
put all the transaction logic in the pxa3xx_nand_irq.
By doing this way, we could dramatically increase the
performance by avoid unnecessary delay.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The previous probe function is some kind of big part.
This patch seperate the resource allocation to keep the probe process
more clear than before.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The number of corrected ECC errors should be reported since other MTD
systems make use of this information (such as UBI data scrubbing).
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In 'verify_bbt_descr()', first check the "bd" pointer, then
dereference it.
Comments amended by Artem.
Signed-off-by: Stanislav Fomichev <kernel@fomichev.me>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some SAM9 chips have the ability to perform DMA between CPU and SMC controller.
This patch adds DMA support for SAM9RL, SAM9G45, SSAM9G46,AM9M10, SAM9M11.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Tested-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_get() returns a struct clk cookie to the driver and some platforms
may return NULL if they only support a single clock. clk_get() has only
failed if it returns a ERR_PTR() encoded pointer.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since 43cc71eed1 (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch overrides nand ecc layout and bad block descriptor (for 8-bit
device) to support hw ecc in romcode layout. So as to have in sync with ecc
layout throughout; i.e. x-loader, u-boot and kernel.
This enables to flash x-loader, u-boot, kernel, FS images from kernel itself
and compatiable with other tools.
This patch does not enables this feature by default and need to pass from
board file to enable for any board.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch makes it possible to select sw or hw (different layout options)
ecc scheme supported by omap nand driver.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configure the FIFO THREASHOLD value different for read and write to keep busy
both filling and to drain out of FIFO at reading and writing.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
nand transfer type (sDMA, Polled, prefetch) can be select from board file,
enabling all transfer type in driver, by default.
this helps in multi-omap build and to select different transfer type for
different board.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
zoom3 and 3630-sdp having the x16 nand device.
This patch configure gpmc as x16 and select the currect function in driver
for polled mode (without prefetch enable) transfer.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are two spellings in use for 'freeze' + 'able' - 'freezable' and
'freezeable'. The former is the more prominent one. The latter is
mostly used by workqueue and in a few other odd places. Unify the
spelling to 'freezable'.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Steven Whitehouse <swhiteho@redhat.com>
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
"info->cmdset" gets dereferenced in __readid() so it needs to be
initialized earlier in the function. This bug was introduced in
18c81b1828 "mtd: pxa3xx_nand: remove the flash info in driver
structure".
Cc: stable@kernel.org [2.6.37+]
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Initialize mtd->writebufsize to be equal to mtd->writesize.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
See commit: c0cbfd0e81
Using __nand_correct_data() helper function, this driver can read 512
byte (with 6 byte ECC) at a time.
This is correct, but not more:
With NAND chips providing page sizes > 512 Bytes
chip->ecc.bytes are calculated > 6 in txx9ndfmc_nand_scan.
According the data sheet there are (only) 6 bytes ECC available.
After applying the patch a Hynix 512M*8 with 2KiB page size could be
successfully formatted and used with an ubifs file system.
Signed-off-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a common requirement for not using OMAP specific omap_readw() /
omap_writew() function calls in drivers/, but replace them with
readw() / writew() on ioremap()ped addresses passed from arch/ instead.
The patch implements this idea for the Amstrad Delta NAND driver. To be
able to use the modified driver, the board file is updated with the
platform device I/O resource declaration, which is passed from there.
Created and tested against linux-2.6.37-rc5, on top of recent patch
'MTD: NAND: ams-delta: convert to platform driver'.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that the Amstrad Delta NAND driver is converted to a platform driver,
which prevents it from interfering with other unrelated hardware in multiple
OMAP1 cpu and machine configurations, it can be automatically configured for
being built into the kernel if the Amstrad Delta board is also selected.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In checking for the ONFI revision, the first conditional (for checking
"unsupported" ONFI) seems unnecessary. All ONFI revisions should be
backwards-compatible; even if this is not the case on some newer ONFI
revision, it should simply fail the second version-checking if-else block
(i.e., the bit-fields for 1.0, 2.0, etc. would not be set to 1). Thus, we
move our "unsupported" condition after having checked each bit field.
Also, it's simple enough to add a condition for ONFI revision 2.3. Note
that this does *NOT* mean we handle all new features of ONFI versions
above 1.0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We have the order of the conditional wrong for choosing the ONFI chip name
vs. the ID table name. Without this fix, we will almost *always* choose a
NULL string to print out instead of the correct one.
This has already been suggested by Matthieu Castet.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In its current form, the driver may interfere with different hardware on
different boards if built into the kernel, hence is not suitable for
inclusion into a defconfig, inteded to be usable with multiple OMAP1 cpu and
machine types.
Convert it to a platform driver, that should be free from this issue.
Created and tested against linux-2.6.37-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This reverts commit e14feafbe0.
The commit limits the maximum amount of bytes which can be read
at one go to the OOB size, which is incorrect, because mtd->read_oob()
allows reading multiple pages at a time, see comment near
"struct mtd_oob_ops" at include/linux/mtd/mtd.h. So this patch
breaks ABI and hence, has to be reverted.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Commit 2c01946c6b (omap3 nand: cleanup
virtual address usages) wrongly enabled CONFIG_MTD_NAND_OMAP_HWECC
which breaks boards like beagle and pandora that use software ECC
for write.
Boards like beagle and pandora uses sw ecc for write (e.g. binary flushed
from u-boot) and read from kernel.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The FSMC actually has a standard ARM PrimeCell ID register, and
the "revision" part of that register contains the thing that
the code is looking at. Reuse the infrastructure from the AMBA
bus abstraction and rid local defines.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This removes the PARTITION macro that David didn't like and also
removes a local variable that was dangling unused in some #ifdefs
by being a bit more clever.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If CONFIG_MTD_PARTITIONS is not selected, then the following warning is generated:
CC drivers/mtd/nand/mxc_nand.o
drivers/mtd/nand/mxc_nand.c: In function 'mxcnd_probe':
drivers/mtd/nand/mxc_nand.c:1014: warning: unused variable 'nr_parts'
Fix it by marking nr_parts as __maybe_unused.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch should fix the following problem:
1. the jffs2-image update in the u-boot was ok
2. first restart and first mount of the NAND-flash-partition was also ok
3. before the restart of controller there are no any activity on NAND-flash except of the jffs2_gcd_mtdX-process ...
4. BUT after the second restart the NAND-flash-partition could not be really used after the second mount,
dmesg filled with messages:
...
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03ce0000: 0xc0ff instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03d00000: 0xc0ff instead
....
Just for for info:
the behaviour observed on mpc8313-based board with the large-page NAND.
The only activity on NAND-flash was the garbage collector process, that looks for CLEANMARKER-nodes
As Scott said it was broken by commit 3ab8f2a2e7
Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When run mtd_oobtest case, there will be one error for step(4),
which turned out it need add one check for out of page read in
nand_do_read_oob just like mtd_do_write_oob did it already.
This commit also fix one typo error for comments in mtd_do_write_oob
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Warning(include/linux/mtd/nand.h:543): No description found for parameter 'badblockbits'
Warning(drivers/mtd/nand/nand_bbt.c:1101): No description found for parameter 'mtd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using %pR standardizes the struct resource output.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that the mtd core supports more then 64 ecc bytes we can use it instead of
some a custom hack in the jz4740 nand driver.
This patch removes the custom {read,write}_page handlers from the jz4740 nand
driver. Thus the driver will now fallback to the default handlers from the nand
core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (82 commits)
mtd: fix build error in m25p80.c
mtd: Remove redundant mutex from mtd_blkdevs.c
MTD: Fix wrong check register_blkdev return value
Revert "mtd: cleanup Kconfig dependencies"
mtd: cfi_cmdset_0002: make sector erase command variable
mtd: cfi_cmdset_0002: add CFI detection for SST 38VF640x chips
mtd: cfi_util: add support for switching SST 39VF640xB chips into QRY mode
mtd: cfi_cmdset_0001: use defined value of P_ID_INTEL_PERFORMANCE instead of hardcoded one
block2mtd: dubious assignment
P4080/mtd: Fix the freescale lbc issue with 36bit mode
P4080/eLBC: Make Freescale elbc interrupt common to elbc devices
mtd: phram: use KBUILD_MODNAME
mtd: OneNAND: S5PC110: Fix double call suspend & resume function
mtd: nand: fix MTD_MODE_RAW writes
jffs2: use kmemdup
mtd: sm_ftl: cosmetic, use bool when possible
mtd: r852: remove useless pci powerup/down from suspend/resume routines
mtd: blktrans: fix a race vs kthread_stop
mtd: blktrans: kill BKL
mtd: allow to unload the mtdtrans module if its block devices aren't open
...
Fix up trivial whitespace-introduced conflict in drivers/mtd/mtdchar.c
Conflicts:
drivers/mtd/mtd_blkdevs.c
Merge Grant's device-tree bits so that we can apply the subsequent fixes.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
When system uses 36bit physical address, res.start is 36bit
physical address. But the function of in_be32 returns 32bit
physical address. Then both of them compared each other is
wrong. So by converting the address of res.start into
the right format fixes this issue.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move Freescale elbc interrupt from nand driver to elbc driver.
Then all elbc devices can use the interrupt instead of ONLY nand.
For former nand driver, it had the two functions:
1. detecting nand flash partitions;
2. registering elbc interrupt.
Now, second function is removed to fsl_lbc.c.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
RAW writes were broken by 782ce79a45
which introduced a check of ops->ooboffs in nand_do_write_ops().
When writing in RAW mode this is called with an ops struct on the stack
of mtdchar.c:mtd_write() which does not initialise ops->ooboffs, so it
is garbage and fails this test.
This test does not make sense if ops->oobbuf is NULL, which it is in the
RAW write path, so include that in the test.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It turns out that pci core now handles these, so this code is redundant
and can even cause bugs
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The bbt structure isn't actually used, just the badblockpos. This lets
the driver correctly handle badblocks with the different OOB layout with
certain sized flashes. Previously, the blocks would all be reported as
bad and be completely unusable.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes sparse warning for static declaration of variable "use_dma"
drivers/mtd/nand/omap2.c:114:11: warning: symbol 'use_dma' was not declared. Should it be static?
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds the appropriate conversions to correct the endianness
issues in the MTD driver whenever it accesses the device tree (which is
always big endian).
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I used this to check the BBT on flash together with a hack in mtdchar in
order to read bad blocks.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
it will create an empty BBT table without considering vendor's BBT
information. Vendor's information may be unavailable if the NAND
controller has a different DATA & OOB layout or this information may be
allready purged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The first (sixt) byte in the OOB area contains vendor's bad block
information. During identification of the NAND chip this information is
collected by scanning the complete chip.
The option NAND_USE_FLASH_BBT is used to store this information in a sector so
we don't have to scan the complete flash. Unfortunately the code stores
a marker in order to recognize the BBT in the OOB area. This will fail
if the OOB area is completely used for ECC.
This patch introduces the option NAND_USE_FLASH_BBT_NO_OOB which has to be
used with NAND_USE_FLASH_BBT. It will then store BBT on flash without
touching the OOB area. The BBT format on flash remains same except the
first page starts with the recognition pattern followed by the version byte.
This change was tested in nandsim and it looks good so far :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No code change.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Not all the NAND devices have all the information in additional
id bytes.
So add a hook in the nand_chip{} is a good method to calculate the
right value of oobsize, erasesize and so on.
Without the hook,you will get the wrong value, and you have to hack
in the ->scan_bbt() to change the wrong value which make the code
mess.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is the same driver submitted by ST Micros SPEAr team but
generalized and tested on the ST-Ericsson U300. It probably
easily works on the NHK8815 too.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently MTD caches the last read NAND page, even if there was an uncorrectable ECC
error. This patch prevents caching in case of uncorrectable ECC errors. The reason
is that we want to allow the user to re-read the NAND page several times. In case of
unstable bits re-trying may help.
Moreover, current behavior is wrong because the first read returns -EBADMSG (correctly)
but the second read succeeds and incorrectly returns 0 (because we read from the cache).
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the build warning:
drivers/mtd/nand/fsl_upm.c: In function 'fun_chip_init':
drivers/mtd/nand/fsl_upm.c:190: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Only 3 warnings are left, one is off by one character, but splitting the line
would reduce the readability. One is for a for loop statement, which would also
not improve readability. The last one is a false positive on a test.
Artem: it is much easier to verify patches against nand_base.c with
checkpatch.pl when nand_base.c itself does not have so many
checkpatch.pl warnings.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Artem: it is much easier to verify patches against nand_base.c with
checkpatch.pl when nand_base.c itself does not have so many
checkpatch.pl warnings.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sudhakar found out that 100µs are enough. Sadly, his updated patch was
overlooked and an older version still using 100ms was merged. Fix this.
Reference: http://patchwork.ozlabs.org/patch/59180/
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In order to reduce the indentation and improve the readability of nand_get_
flash_type, split the ONFI detection logic to its own function. The detection
logic inside nand_flash_detect_onfi is also rewritten to allow for less
indentation.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for reading NAND device ONFI parameters and use
the ONFI informations to define its geometry. In case the device supports
ONFI, the onfi_version field in struct nand_chip contains the version (BCD)
and the onfi_params structure can be used by drivers to set up timings and
such. We currently only support ONFI 1.0 parameters.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are some additions to the detection scheme used by Samsung
MLC NAND. These simple changes to support the 400- and 436-byte OOB
are found in the following data sheet:
Samsung K9GBG08U0M (p.40)
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For different command need different oob requirement, set the proper
oob length by different cmd.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After probe, all info already transfer to driver structure.
There is no need to keep the original flash info.
So that we could safely free the flash info in memory, which may grows
larger when more flash is suported.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We certainly don't need to send read id command times by times, since
we already know what the id is after the first read id...
So create a default timing which could ensure it would successfully read
id out all supported chip. Then follow the build-in table to reconfigure
the timing.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adding a new flash definition would need less code.
Keep the platform passing flash definition method.
If one flash is both defined in platform data and builtin table,
driver would select the one from platform data first.
By this way, platform could select the timing most suit for itself,
not need to follow the common settings.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Toshiba does not use ONFI for their NAND flash. So we have to continue
to add new IDs used by Toshiba devices as well as heuristic detection
for scanning the 2nd page for a BBM. This is a relatively harmless
start at supporting many of them.
These chips mostly follow the same ID fields of previous generations,
but there is a need for a tweak.
These chips introduce a strange 576 byte OOB (that's 36 bytes per
512 bytes of page). In the preliminary data, Toshiba has not
defined exactly how their ID strings should decode. In the future,
a new tweak must be added.
Data is taken from, among others, Toshiba TC58TxG4S2FBAxx
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
struct nand_ecclayout is too small for many new chips; OOB regions can be as
large as 448 bytes and may increase more in the future. Thus, copying that
struct to user-space with the ECCGETLAYOUT ioctl is not a good idea; the ioctl
would have to be updated every time there's a change to the current largest
size.
Instead, the old nand_ecclayout is renamed to nand_ecclayout_user and a
new struct nand_ecclayout is created that can accomodate larger sizes and
expand without affecting the user-space. struct nand_ecclayout can still
be used in board drivers without modification -- at least for now.
A new function is provided to convert from the new to the old in order to
allow the deprecated ioctl to continue to work with truncated data. Perhaps
the ioctl, the conversion process, and the struct nand_ecclayout_user can be
removed altogether in the future.
Note: There are comments in nand/davinci_nand.c::nand_davinci_probe()
regarding this issue; this driver (and maybe others) can be updated to
account for extra space. All kernel drivers can use the expanded
nand_ecclayout as a drop-in replacement and ignore its benefits.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some Spansion chips have a method for determining eraseblock size that
is incompatible with similar ID chips of other sizes. This implements
some heuristic detection of these differences.
This patch checks for a 5-byte ID with trailing zeros as well as a
512-byte page size to ensure that chips are not misdetected as the
S30MLxxxP ORNAND series.
[Tweaked by Artem a bit]
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Drivers may (and do) return negative errno values other than -1 from the
ecc.correct callback.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch reverts the driver to enabling/disabling the NFC interrupt
mask rather than enabling/disabling the system interrupt. This cleans
up the driver so that it doesn't rely on interrupts being disabled
within the interrupt handler.
For i.MX21 we keep the current behaviour, that is calling
enable_irq/disable_irq_nosync to enable/disable interrupts. This patch
is based on earlier work by John Ogness.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch modifies the DaVinci NAND driver to use the
new AEMIF timing setup API to configure the NAND access
timings.
Earlier, AEMIF configuration was being done as a special
case for DM644x board, but now more boards emerge which have
capability to boot for other media (SPI flash, NOR flash) and
have the kernel access NAND flash. This means that kernel cannot
always depend on the bootloader to setup the NAND.
Also, on platforms such as da850/omap-l138, the aemif input
frequency changes as cpu frequency changes; necessiating
re-calculation of timimg values as part of cpufreq transtitions.
This patch forms the basis for adding that support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds support to configure the AEMIF interface
with supplied timing values.
Since this capability is useful both from NOR and NAND
flashes, it is provided as a new interface and in a file
of its own.
AEMIF timing configuration is required in cases:
1) Where the AEMIF clock rate can change at runtime (a side
affect of cpu frequency change).
2) Where U-Boot does not support NAND/NOR but supports other
media like SPI Flash or MMC/SD and thus does not care about
setting up the AEMIF timing for kernel to use.
3) Where U-Boot just hasn't configured the timing values and
cannot be upgraded because the box is already in the field.
Since there is now a header file for AEMIF interface, the
common (non-NAND specific) defines for AEMIF registers have
been moved from nand.h into the newly created aemif.h
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch initializes the pages per block field in CONFIG1 for
v2 controllers. It also sets the FP_INT field. This is the last
field not correctly initialized, so we can switch from
read/modify/write the CONFIG1 reg to just write the correct
value.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since info->mtd isn't dynamically allocated, we shouldn't attempt to
kfree() it. Otherwise we get random fun corruption when unloading
the driver built as a module.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Seems some patches got out sync when being merged. The Blackfin NFC
driver was updated to use nand_scan_ident(), but it missed the change
where nand_scan_ident() now takes 3 arguments. So update this driver
to fix build failures.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch avoids byte access to the NFC buffer. Byte access to the
NFC is not allowed.
The patch is against linux-next 20100618.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Apparently, the check for a 6-byte ID string introduced by commit
426c457a32 ("mtd: nand: extend NAND flash
detection to new MLC chips") is NOT sufficient to determine whether or
not a Samsung chip uses their new MLC detection scheme or the old,
standard scheme. This adds a condition to check cell type.
Signed-off-by: Tilman Sauerbeck <tilman@code-monkey.de>
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Commit c7b28e25cb ("mtd: nand: refactor BB
marker detection") caused a regression in detection of factory-set bad
block markers, especially for certain small-page NAND. This fix removes
some unneeded constraints on using NAND_SMALL_BADBLOCK_POS, making the
detection code more correct.
This regression can be seen, for example, in Hynix HY27US081G1M and
similar.
Signed-off-by: Brian Norris <norris@broadcom.com>
Tested-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Test on a PXA310 platform with Samsung K9F2G08X0B NAND flash,
with tCH=5 and clk is 156MHz, ns2cycle(5, 156000000) returns -1.
ns2cycle returns negtive value will break NDTR0_tXX macros.
After checking the commit log, I found the problem is introduced by
commit 5b0d4d7c8a
"[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accurately"
To get num of clock cycles, we use below equation:
num of clock cycles = time (ns) / one clock cycle (ns) + 1
We need to add 1 cycle here because integer division will truncate the result.
It is possible the developers set the Min values in SPEC for timing settings.
Thus the truncate may cause problem, and it is safe to add an extra cycle here.
The various fields in NDTR{01} are in units of clock ticks minus one,
thus we should subtract 1 cycle then.
Thus the correct equation should be:
num of clock cycles = time (ns) / one clock cycle (ns) + 1 - 1
= time (ns) / one clock cycle (ns)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
* git://git.infradead.org/mtd-2.6:
mtd/nand_ids: Fix buswidth
mtd/m25p80: fix test for end of loop
mtd/m25p80: retlen is never NULL
MIPS: Fix gen_nand probe structures contents
gen_nand: Test if nr_chips field is valid
BFIN: Fix gen_nand probe structures contents
nand/denali: move all hardware initialization work to denali_hw_init
nand/denali: Add a page check in denali_read_page & denali_read_page_raw
nand/denali: use cpu_relax() while waiting for hardware interrupt
nand/denali: change read_status function method
nand/denali: Fixed check patch warnings
ARM: Fix gen_nand probe structures contents
mtd/nand_base: fix kernel-doc warnings & typos
nand/denali: use dev_xx debug function to replace nand_dbg_print and some printk
nand/denali: Fixed handle ECC error bugs
nand/denali: use iowrite32() to replace denali_write32()
nand/denali: Fixed probe function bugs
The buswidth for chips of ID 0xD7 is x8, not x16.
This was my previous typo.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All hardware initialization will be done in denali_hw_init before
irq handler registered
Change mtd name from "DENALI NAND" to be "denali-nand" since whitespace in
name can cause problems if we use cmdlinepart
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In mtd->write, Denali controller will use MODE_11 mode to read
NAND flash status, then return back to MODE_1O mode to do page
write.
Here comes a bug for this kind of using, sometimes controller will
not write data to NAND and just return a good interrupt to tell
driver writing work is done. The data in this page is all 0xff and
this page can not be written again. The reason is unknow.
So read Denali controller register WRITE_PROTECT to get NAND status
instead.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
waring: no space for starting a line
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix mtd/nand_base.c kernel-doc warnings and typos.
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'invert'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:2087): No description found for parameter 'len'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mtd/nand_base.c kernel-doc warnings and typos.
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'invert'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:2087): No description found for parameter 'len'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Once the last ECC error was handled, controller will triger an
interrupt. If this interrupt can not be clean on time, controller
may corrupt.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
denali_write32() just implements a debug function for iowrite32(),
only print out the write value. Remove this function since it's useless
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixed a pci_resource_len function error;
Changed returning sequence of probe function;
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (79 commits)
mtd: Remove obsolete <mtd/compatmac.h> include
mtd: Update copyright notices
jffs2: Update copyright notices
mtd-physmap: add support users can assign the probe type in board files
mtd: remove redwood map driver
mxc_nand: Add v3 (i.MX51) Support
mxc_nand: support 8bit ecc
mxc_nand: fix correct_data function
mxc_nand: add V1_V2 namespace to registers
mxc_nand: factor out a check_int function
mxc_nand: make some internally used functions overwriteable
mxc_nand: rework get_dev_status
mxc_nand: remove 0xe00 offset from registers
mtd: denali: Add multi connected NAND support
mtd: denali: Remove set_ecc_config function
mtd: denali: Remove unuseful code in get_xx_nand_para functions
mtd: denali: Remove device_info_tag structure
mtd: m25p80: add support for the Winbond W25Q32 SPI flash chip
mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips
mtd: m25p80: add support for the EON EN25P{32, 64} SPI flash chips
...
Fix up trivial conflicts in drivers/mtd/maps/{Kconfig,redwood.c} due to
redwood driver removal.
Nand devices with at least 26 bytes of oob data per 512 byte block
can have 8bit ecc on v2 type controllers. This is currently not tested,
but at least this patch puts the ECC_MODE bit into a well defined state.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The v2 controller has a totally different mechanism to check
whether the data we read had ecc errors or not. Implement this.
The mechanism in the v2 controller happens to be identical to
the v3 controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This prepares the driver for v3 support. The v3 controller
has a completely different register layout, so add a V1_V2_
namespace to the register defines to avoid confusion with
the v3 regs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch prepares the driver to add v3 controller support
later. The v3 controller is basically the same controller as v1
and v2, but with a completely different register layout.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We save/restore the value in the buffer anyway, so it makes
no difference whether we use main_area0 or main_area1. So,
we can use main_area0 and remove main_area1 from the driver
which is otherwise unused. Also, clean up the comments in
get_dev_status.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the offset to the register base instead. This is done
in preparation for v3 controller support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
set_ecc_config function only set ECC_CORRECTION register, so
move register setting to probe function.
Since controller only support 15bit and 8bit ecc correction,
updated nand ecc layout information.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Hi David,
I sent 4 patches using my intel email account. If there is any
problem about the format of these patches, I will resend them after
I arrived at home by using my gmail account, and I will keep on
using gmail account to send patches.
Thanks.
>From 242e3bf5e17f54b1df8cf285154a7c7a61ff62e9 Mon Sep 17 00:00:00 2001
From: Chuanxiao Dong <chuanxiao.dong@intel.com>
Date: Fri, 6 Aug 2010 15:29:41 +0800
Subject: [PATCH 1/4] mtd: denali: Remove device_info_tag structure.
Most of the variables in this structure are useless, so just
remove this structure and relevant codes.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
This patch fixes
drivers/mtd/nand/atmel_nand.c:372: warning: 'part_probes' defined but not used
which is issued when CONFIG_MTD_PARTITIONS is defined but
CONFIG_MTD_CMDLINE_PARTS not.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch corrects a problem where gen_nand driver assumed there can be only
one chip and ignored the pdata->chip.nr_chips value.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In denali driver, wTotalBlocks variable is useless, so just
remove them in get_toshiba_nand_para and get_hynix_nand_para
first. Other wTotalBlocks in denali.c and other variables in
dev_info struct are also useless, will remove them later.
Also add a parameter in get_hynix_nand_para to prepare to
remove dev_info struct. This parameter comes by reading NAND
ID directly. Reading register will report wrong value for
some NAND chips, e.g. some Micron MT29F32G08QAA chips.
So update NAND_CMD_READID method as well.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
rename these functions' name and remove additional declarations
in header file
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (150 commits)
MIPS: PowerTV: Separate PowerTV USB support from non-USB code
MIPS: strip the un-needed sections of vmlinuz
MIPS: Clean up the calculation of VMLINUZ_LOAD_ADDRESS
MIPS: Clean up arch/mips/boot/compressed/decompress.c
MIPS: Clean up arch/mips/boot/compressed/ld.script
MIPS: Unify the suffix of compressed vmlinux.bin
MIPS: PowerTV: Add Gaia platform definitions.
MIPS: BCM47xx: Fix nvram_getenv return value.
MIPS: Octeon: Allow more than 3.75GB of memory with PCIe
MIPS: Clean up notify_die() usage.
MIPS: Remove unused task_struct.trap_no field.
Documentation: Mention that KProbes is supported on MIPS
SAMPLES: kprobe_example: Make it print something on MIPS.
MIPS: kprobe: Add support.
MIPS: Add instrunction format for BREAK and SYSCALL
MIPS: kprobes: Define regs_return_value()
MIPS: Ritually kill stupid printk.
MIPS: Octeon: Disallow MSI-X interrupt and fall back to MSI interrupts.
MIPS: Octeon: Support 256 MSI on PCIe
MIPS: Decode core number for R2 CPUs.
...
Hi,
I have changed the outlook mail cliet to be linux mutt client and use my
personal gmail to submit patches.
Here are 5 new patches to fix nand/denali check patch errors. The other
4 patches will be sent out after this mail.
Thanks for your review.
>From d125ad3f57bbf517131dccad6b5933edf8c2632a Mon Sep 17 00:00:00 2001
From: Chuanxiao Dong <chuanxiao.dong@intel.com>
Date: Tue, 3 Aug 2010 15:54:48 +0800
Subject: [PATCH 1/5] mtd: denali.c: clean up all whitespaces in code indent
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The IRQSTAT register is a W1C register used by the interrupt handler and
may have its BUSY bit changed. This makes it somewhat unreliable for the
polling devready function. So switch it over to use the BUSY bit in the
STAT register that always reflects the current state of the hardware.
This fixes driver hangs seen when the NAND flash is under heavy system
load (like I/O benchmarks).
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Rather than forcing the platform resources to declare the desired page
size, simply use the existing information passed down to us by the higher
layers. This way we work out of the box with all flash chips that the
kernel knows about.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When resetting the ECC registers/counters, the bit will automatically
clear itself once the reset has actually finished. So make sure we
wait for that to occur before doing anything else rather than assuming
everything is peachy and proceeding with stale ECC values.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We used the platform rd_dly field when we meant to use the wr_dly field.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND base may send some controls which are neither CLE nor ALE, so
we need to explicitly check both instead of assuming things are always
one or the other. Otherwise, we sometimes send out illegal addresses
to the NAND device.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Our write_buf/read_buf funcs always do ECC in HW ECC mode. That is not
needed for raw funcs. In fact, write_buf/read_buf should be a pure func
for data input/output while chip->ecc.hwctl controls ECC. Unfortunately,
we can't separate ECC from normal data input/output in our NFC, so our DMA
write_buf/read_buf entries are coupled with ECC operations closely.
Thus we need to provide dedicated read_page_raw/write_page_raw funcs where
we do non-DMA transactions so as to avoid automatic ECC.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The low level NAND driver doesn't care about filesystems, so punt the
local comment indicating otherwise.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The mtd layer is responsible to call mtd->{suspend,resume}. Doing it
again in the driver is wrong and results in a warning:
nand_resume called for a chip which is not in suspended state
at resume time. Removing the calls from the resume and suspend
functions makes them empty allowing them to be deleted completely.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The variable 'syn' was being used uninitialized. Also
fixed incorrect use of syn[] vs s[].
Tested on powerpc board with 64MiB DOC2000.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch removes direct reference of gpmc address from generic nand platform code.
Nand platform code now uses wrapper functions which are implemented in gpmc module.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
few functions added in gpmc module and to be used by other drivers like NAND.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is an update that depends on the previous patches I sent.
We can now write to all the appropriate BB marker locations (i.e.
pages 1 AND 2, bytes 1 AND 6) with nand_default_block_markbad() if
necessary, according to the flags marked in chip->options.
Note that I removed the line:
ofs += mtd->oobsize;
Unless I am wrong, this line was completely unnecessary in the
first place.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix all checkpatch.pl complaints.
Artem: tweaked a little and fix tab indentations, so now this is not
only about checkpatch, but also about making indentations look
sane.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On TI's DA830/OMAP-L137, DA850/OMAP-L138 and DM365, after setting the
4BITECC_ADD_CALC_START bit in the NAND Flash control register to 1 and
before waiting for the NAND Flash status register to be equal to 1, 2 or
3, we have to wait till the ECC HW goes to correction state. Without this
wait, ECC correction calculations will not be proper.
This has been tested on DA830/OMAP-L137, DA850/OMAP-L138, DM355 and DM365
EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a revision to PATCH 2/2 that I sent. Link:
http://lists.infradead.org/pipermail/linux-mtd/2010-July/030911.html
Added new flag for scanning of both bytes 1 and 6 of the OOB for
a BB marker (instead of simply one or the other).
The "check_pattern" and "check_short_pattern" functions were updated
to include support for scanning the two different locations in the OOB.
In order to handle increases in variety of necessary scanning patterns,
I implemented dynamic memory allocation of nand_bbt_descr structs
in new function 'nand_create_default_bbt_descr()'. This replaces
some increasingly-unwieldy, statically-declared descriptors. It can
replace several more (e.g. "flashbased" structs). However, I do not
test the flashbased options personally.
How this was tested:
I referenced 30+ data sheets (covering 100+ parts), and I tested a
selection of 10 different chips to varying degrees. Particularly, I
tested the creation of bad-block descriptors and basic BB scanning on
three parts:
ST NAND04GW3B2D, 2K page
ST NAND128W3A, 512B page
Samsung K9F1G08U0A, 2K page
To test these, I wrote some fake bad block markers to the flash (in OOB
bytes 1, 6, and elsewhere) to see if the scanning routine would detect
them properly. However, this method was somewhat limited because the
driver I am using has some bugs in its OOB write functionality.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some level of support for various scanning locations was already built in,
but this required clean-up. First, BB marker location cannot be determined
_only_ by the page size. Instead, I implemented some heuristic detection
based on data sheets from various manufacturers (all found in
nand_base.c:nand_get_flash_type()).
Second, once these options were identified, they were not handled properly
by nand_bbt.c:nand_default_bbt(). I updated the static nand_bbt_desc structs
to reflect the need for more combinations of detection. The memory allocation
here probably needs to be done dynamically in the very near future (see next
patches).
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Current driver prevents command-line partitions from being parsed when built-in
partitions are defined in s3c2410_nand_set object, but it is not desirable in some
cases. This patch tries to parse commad-line partitions prior to the built-in.
Signed-off-by: Conke Hu <conke@maxwit.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
NAND_BB_LAST_PAGE used to be in nand.h, but it pertained to bad block
management and so belongs next to NAND_BBT_SCAN2NDPAGE in bbm.h. Also,
its previous flag value (0x00000400) conflicted with NAND_BBT_SCANALLPAGES
so I changed its value to 0x00008000. All uses of the name were modified to
provide consistency with other "NAND_BBT_*" flags.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Included the basic size info for NAND chips with ID of 0xAD or
0xD7. The first can be found in Hynix HY27SF161G2M, while the
second can be found in Micron MT29F64G08 and the Samsung K9LBG08U0D
(among others). Also, some 64 Gbit (or larger) chips identify as
0xD7 because they contain multiple smaller 32 Gbit chips. I
assume it's safe to classify these under the 32 Gbit listing.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes:
drivers/mtd/nand/mxc_nand.c: In function 'mxcnd_resume':
drivers/mtd/nand/mxc_nand.c:901: warning: unused variable 'host'
Removing this variable was missed in 9c14b153e6.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Look for dependency checks for "FOO" when inside of an "if FOO" block and remove them.
Signed-off-by: Kyle Spaans <kspaans@uwaterloo.ca>
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>
* git://git.infradead.org/~dwmw2/mtd-2.6.35:
jffs2: update ctime when changing the file's permission by setfacl
jffs2: Fix NFS race by using insert_inode_locked()
jffs2: Fix in-core inode leaks on error paths
mtd: Fix NAND submenu
mtd/r852: update card detect early.
mtd/r852: Fixes in case of DMA timeout
mtd/r852: register IRQ as last step
drivers/mtd: Use memdup_user
docbook: make mtd nand module init static
Fixes build errors in drivers caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move MTD_NAND_ECC and MTD_NAND_ECC_SMC above NAND memuconfig, to unbreak
display in xconfig. This shouldn't change any dependencies.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes build errors in drivers caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build errors caused by the:
- OF device_node pointer being moved into struct device
- removal of the match_table field from struct of_platform_driver
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This turns out to be the reason for DMA timeouts on resume,
if card was inserted while system was suspended
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Don't call complete on dma completion
* do a INIT_COMPLETE before using it each time
* Report DMA read error via ecc 'correct'
I finally managed to make my system do suspend to ram propertly, and I see that
if card was inserted during suspend (while system was off), I get dma timeouts
on resume. Simple card reinsert solves the issue.
This patch solves a crash that would happen otherwise
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Otherwise, if it fires right away, it might access
uninitialized spinlock
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
This reverts commit 66803762 ("mtd: mxc_nand: add RESET command support").
Support for NAND_CMD_RESET was added separately in commit d4840180
("mtd: mxc_nand: set NFC registers after reset"), causing a build error:
drivers/mtd/nand/mxc_nand.c: In function 'mxc_nand_command':
drivers/mtd/nand/mxc_nand.c:689: error: duplicate case value
drivers/mtd/nand/mxc_nand.c:606: error: previously used here
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This NAND flash part advertises 0xD1 as an identifier but is still a working
128MBytes x 8bits 3.3V NAND part.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a slightly modified version of a patch submitted last year by
Reuben Dowle <reuben.dowle@navico.com>. His original comments follow:
This patch adds support for some MLC NAND flashes that place the BB
marker in the LAST page of the bad block rather than the FIRST page used
for SLC NAND and other types of MLC nand.
Lifted from Samsung datasheet for K9LG8G08U0A (1Gbyte MLC NAND):
"
Identifying Initial Invalid Block(s)
All device locations are erased(FFh) except locations where the initial
invalid block(s) information is written prior to shipping. The initial
invalid block(s) status is defined by the 1st byte in the spare area.
Samsung makes sure that the last page of every initial invalid block has
non-FFh data at the column address of 2,048.
...
"
As far as I can tell, this is the same for all Samsung MLC nand, and in
fact the samsung bsp for the processor used in our project (s3c6410)
actually contained a hack similar to this patch but less portable to
enable use of their NAND parts. I discovered this problem when trying to
use a Micron NAND which does not used this layout - I wish samsung would
put their stuff in main-line to avoid this type of problem.
Currently this patch causes all MLC nand with manufacturer codes from
Samsung and ST(Numonyx) to use this alternative location, since these
are the manufactures that I know of that use this layout.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some of the newer MLC devices have a 6-byte ID sequence in which
several field definitions differ from older chips in a manner that is
not backward compatible. For instance:
Samsung K9GAG08U0M (5-byte sequence): ec d5 14 b6 74
4th byte, bits 1:0 encode the page size: 0=1KiB, 1=2KiB, 2=4KiB, 3=8KiB
4th byte, bits 5:4 encode the block size: 0=64KiB, 1=128KiB, ...
4th byte, bit 6 encodes the OOB size: 0=8B/512B, 1=16B/512B
Samsung K9GAG08U0D (6-byte sequence): ec d5 94 29 34 41
4th byte, bits 1:0 encode the page size: 0=2KiB, 1=4KiB, 3=8KiB, 4=rsvd
4th byte, bits 7;5:4 encode the block size: 0=128KiB, 1=256KiB, ...
4th byte, bits 6;3:2 encode the OOB size: 1=128B/page, 2=218B/page
This patch uses the new 6-byte scheme if the following conditions are
all true:
1) The ID code wraps around after exactly 6 bytes
2) Manufacturer is Samsung
3) 6th byte is zero
The patch also extends the maximum OOB size from 128B to 256B.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for a board to register a callback to get the state of the
RnB line if it has it attached.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2GB xD card, and 4MB SmartMedia ROM card share same ID, so to make both work
split xD and smartmedia ID tables.
Hardware driver must be able to know which type it handles (and probably just one).
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On i.MX21 SoCs, if the NFC_CONFIG1:NFC_INT_MASK bit is set,
NFC_CONFIG2:NFC_INT always reads out zero, even if an
operation is completed. This patch uses enable_irq and
disable_irq_nosync instead of NFC_CONFIG1:NFC_INT_MASK to
mask NFC interrupts. This allows NFC_CONFIG2:NFC_INT to also
be used to detect operation completion on i.MX21.
The i.MX21 NFC does not signal reset completion using
NFC_CONFIG1:NFC_INT_MASK, so instead reset completion is
tested by checking if NFC_CONFIG2 becomes 0.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch allows the mxc_nand driver to reset the NAND
flash controller. NFC registers are (re-)set after
completion of the reset, as a reset will have reverted
the NFC registers to their default values.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/denali.c:1427: error: conflicting types for ‘enable_dma’
arch/powerpc/include/asm/dma.h:189: note: previous definition of ‘enable_dma’ was here
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is more work to be done on this but it is basically working now.
Signed-off-by: Jason Roberts <jason.e.roberts@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The revision in SVR for MPC5123 is 3. The NFC is the same as MPC5121
revision 2.
Signed-off-by: Steve Deiters <SteveDeiters@basler.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The pxa32xx_nand driver doesn't support partition tables from the
command line. This patch adds support for it.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original macro worked only when applied to variables named 'mtd'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert all magic numbers into appropriate defines, and move the defines
out of the global namespace and into this one driver. No other driver
needs to care about the MMR layout anyways.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do not need these names. Moreover, there are spelling typos
there: "nansin" instead of "nandsim".
This patch is just a clean up, no functional changes.
Reported-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We must tell GCC to use even register for variable passed to ldrd
instruction. Without this patch GCC 4.2.1 puts this variable to r2/r3 on
EABI and r3/r4 on OABI, so force it to r2/r3. This does not change
anything when EABI and OABI compilation works OK.
Without this patch and with OABI I get:
CC drivers/mtd/nand/orion_nand.o
/tmp/ccMkwOCs.s: Assembler messages:
/tmp/ccMkwOCs.s:63: Error: first destination register must be even -- `ldrd r3,[ip]'
make[5]: *** [drivers/mtd/nand/orion_nand.o] Error 1
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jamie Lokier <jamie@shareable.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This way drivers could use ecc routines without depedency on whole nand
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Update the Kconfig entry for the sh_flctl driver to
enable build on SH-Mobile ARM platforms.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
... instead of comparing with DMA_ERROR_CODE, which will only work on
powerpc/sparc/x86.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
r852 fails to build when CONFIG_PCI is not enabled since it uses
pci_*() calls and is a PCI driver, so it should depend on PCI
to prevent build errors.
It should also #include <linux/pci.h>.
drivers/mtd/nand/r852.c:1053: error: implicit declaration of function 'pci_prepare_to_sleep'
drivers/mtd/nand/r852.c:1062: error: implicit declaration of function 'pci_back_from_sleep'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix r852 build for the case of CONFIG_PM=n.
drivers/mtd/nand/r852.c:1039: error: implicit declaration of function 'pci_prepare_to_sleep'
drivers/mtd/nand/r852.c:1048: error: implicit declaration of function 'pci_back_from_sleep'
This patch leaves r852_pm_ops untouched.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
First don't enable card detection logic to early. Second be very careful with
DMA engine, to be sure it doesn't write to kernel memory driver doesn't own.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PCI_DEVICE_ID_RICOH_R5C852 was missed in the edited commit, and on
second thought I just open code it.
This fixes compile error.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Test results of few functions that were declared with __must_check
* Fix bogus gcc warning about uinitialized variable 'ret'
* Remove unused variable from mtdblock_remove_dev
* Don't use deprecated DMA_32BIT_MASK
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds a driver for Ricoh R5C852 xD card reader.
This reader is a part of larger mulifunction chip
and found at least in R5C832
Driver is complete, but bewere of the fact that some
(probably only type M) xD cards are 'fake' which means that
they have an on board CPU and expose emulated nand command set
These cards don't even store the oob area on the flash,
but generate it on the fly from something else.
Thus they demand to have proper values written in the oob area,
and therefore only useful with SmartMedia FTL.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
(and remove the CONFIG_MTD_NAND_SMARTMEDIA option which isn't going to be
used now that we're doing it this way)
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This small module implements few helpers that are usefull
for nand drivers for SmartMedia/xD card readers.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This can be used to protect against bitflips in that field, but now mostly
for smartmedia.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This changes the behavier of MTD_OOB_RAW. It used to read both OOB and
data to the data buffer, however you would still need to specify the
dummy oob buffer.
This is only used in one place, but makes it hard to read data+oob
without ECC test, thus I removed that behavier, and fixed the user.
Now MTD_OOB_RAW behaves just like MTD_OOB_PLACE, but doesn't do ECC
validation
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
nand_do_write_ops was broken in regard to writing several pages, each
with its own oob.
Although nand_do_write_ops intends to allow such mode, it fails do do so
Probably this was never tested.
Also add missing checks for attempts to write at illegal offsets.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD_OOB_PLACE is supposed to read/write the raw oob data similiar to the
MTD_OOB_RAW however due to a bug, currently it is not possible to read
more data that is specified by the oob 'free' regions.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since all userspace threads are frozen at the time the nand_suspend is called,
they aren't inside any nand function.
We don't call try_to_freeze in nand ether. Thus the only user that can
be inside the nand functions is an non freezeable kernel thread. Thus we
can safely wait for it to finish.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adds NAND Flash Controller driver for MPC5121 Revision 2.
All device features, except hardware ECC and power management,
are supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In the branch where pagesize equalled NAND_DATA_ACCESS_SIZE, NumToRead
wasn't decremented in the `while (numToRead > 11)' loop.
Also the first and last while loops were duplicated in both branches.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Leo Chen <leochen@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a bug in nand prefetch read routine, which comes into effect
only if nand device is a 16-bit device (as we have in zoom boards).
This bug is effective only with below combination of conditions:
1. nand deivce, in use, is a 16 bit device
2. nand driver supports 'subpage' read
3. SW ECC is in use
This was not seen old kernel (ex: .23), because when, in early days,
we tested this (nand prefetch read in LDP boards) there was no
'subpage read' support.
Later when we had subpage read in (.27) kernel, we had hw ecc enabled
always in our internal tree. So, we missed this bug.
This patch fixes the issue.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Removing OMAP NAND driver, when loaded as a module, gives error and
does not get success. This fixes this and makes driver loadable and
removable run time.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixing below warning in compilation:
drivers/mtd/nand/omap2.c: In function 'omap_write_buf_dma_pref':
drivers/mtd/nand/omap2.c:508: warning: passing argument 2 of
'omap_nand_dma_transfer' discards qualifiers from pointer target type
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mxc_nand driver must support the RESET Command in order to support
Micron NAND which need a reset before any other command.
Signed-off-by: Eric Benard <eric@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add nand lock / unlock routines. At least 'micron' parts
support this.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
... verification for 'nand_erase_nand'
These checks are expected to be used by 'nand_lock' and 'nand_unlock'
routines too. As all these three are block aligned operations.
So, creating a helper function for this makes sense.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MAX_MTD_DEVICES is about to be removed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The clock must already be off after mtd->suspend. Disabling it again
results in an negative overflow of the clock usage count. This didn't
hurt as mxcnd_resume undid it after wake up.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The probe function calls platform_set_drvdata with a valid pointer when
the probe is successful. As mxcnd_suspend and mxcnd_resume are only
called on bound devices, platform_get_drvdata always returns non-NULL.
This fix isn't critical as the pointer is always valid so it doesn't
matter if the compiler generated code for it or not.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The match_table field of the struct of_device_id is constant in <linux/of_platform.h>
so it is worth to make xps2_of_match also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make alauda_table also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make cafe_nand_tbl also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Introducing 'gpmc-nand.c' for GPMC specific NAND init.
For example: GPMC timing parameters and all.
This patch also migrates gpmc related calls from 'nand/omap2.c'
to 'gpmc-nand.c'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit e99030609e ("mtd: orion_nand.c: add
error handling and use resource_size()") introduced a build error -- it
assigns something to a undeclared variable 'err', whereas the rest of
the code uses 'ret' for this task.
This patch fixes this typo and thus removes the build failure.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch extends the sh_flctl driver with support
for 16-bit bus configuration using SEL_16BIT and
support for multiplexed pins using SHBUSSEL.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains a few changes for the sh_flctl driver:
- not sh7723-only driver - get rid of kconfig dependency
- use dev_err() instead of printk()
- use __devinit and __devexit for probe()/remove()
- fix probe() return values
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The ts72xx platform has been updated to use the generic platform nand
driver (plat_nand.c). This removes the now-defunct ts7250.c nand driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Matthieu Crapet <mcrapet@gmail.com>
Cc: Jesse Off <joff@embeddedARM.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Due to I have renamed the platform_device.name,so this patch changes
this nand driver platform_driver name.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove unnecessary casts and use dev_get_platdata() to retrieve the
struct mfd_cell data from the platform.
Use resource_size() for the ioremap()'s.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use platform_get_resource() to fetch the memory resource and
add error handling for when it is missing. Use resource_size()
for the ioremap().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ioremap'ed sizes are off by 1; use resource_size() for correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove unnecessary casts for p_nand, it is already a void __iomem *.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use kzalloc() instead of kmalloc()/memset().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The platform has never been fully merged
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
This reverts commit 82613b0da6, because
commit daa0f15 (mtd: don't use __exit_p to wrap mxcnd_remove) is a
better solution. Not having a remove callback breaks rebinding because
resources are not freed on remove.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I was going to play with a faulty nand image from real flash and noticed
that nandsim does not work with:
first_id_byte=0xec second_id_byte=0xd5 third_id_byte=0x51 fourth_id_byte=0xa6
This patch seems to fix it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since the same nand controller is shared between ARCH_PXA and ARCH_MMP. Move
the pxa3xx_nand.h from mach directory to plat directoy.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
MTD_NAND_PXA3xx module is shared between ARCH_PXA and ARCH_MMP. Update
this configuration according to it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Support samsung 2GbX8 and 32GbX8 nand flash.
Support micron 4GbX8 and 4GbX16 nand flash.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In some bootloader, IRQ is enabled. Writing nand triggers unexpected
interrupts. So disable nand irq in initialization. After nand
initialized and in working state, irq is controlled by nand driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Nand driver uses IRQ_NAND as hardcode irq number. In ARCH_MMP, the irq
number is different. So get irq resource from platform device structure
and use it in initialization and deinitialization code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Although nand controller is same between PXA3xx and MMP, the register space
is different. Remove the hardcode register address setting in pxa3xx_nand.h.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Slow down the tRp of Micron NAND flash timing.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Initialize the read buffer content to 0xFF.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
When fetch nand data with non-DMA mode, we should align info->data_size to
32bit, not 8bit.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The shift operator used here to convert from bytes to 32-bit words is
backwards.
Signed-off-by: David Hunter <hunterd42@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Symptom:
device_suspend(): mtd_cls_suspend+0x0/0x58 returns -11
PM: Device mtd14 failed to suspend: error -11
PM: Some devices failed to suspend
This patch enables other chips to be suspended if the active chip of
the controller has been suspended.
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The existing NAND infrastructure allows the default main and
mirror bad block tables to be overridden in nand_default_bbt().
However, the davinci_nand driver does not support this. Add
that support by adding fields to the davinci driver's platform
data so platform code can pass in their own bbt's and make the
davinci_nand driver honor them.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function mxcnd_remove is defined using __devexit, so don't use
__exit_p but __devexit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function excite_nand_remove is used only wrapped by __devexit_p so
define it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We want error information even if the kernel hasn't been built for verbose
debugging.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently, the program and erase sequences do not wait for completion,
instead relying on a subsequent waitfunc() callback. However, this causes
the chipselect to be deasserted while the NAND chip is still asserting the
busy pin, which can corrupt activity on other chipselects.
This patch switches to using the sequences recommended by the manual,
in which a wait is performed within the initial command sequence. We can
now re-use the status byte from the initial command sequence, rather than
having to do another status read in the waitfunc.
Since we're already touching the command sequences, it also cleans up some
cruft in SEQIN that isn't needed since we cannot program partial pages
outside of OOB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Suchit Lepcha <suchit.lepcha@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When a NAND operation is in progress, all other localbus operations
(including NOR flash) will have to wait for access to the bus. However, the
NAND operation may take longer to complete than the default timeout. Thus,
if NOR is accessed while a NAND operation is in progress, the NAND operation
will fail.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Return a negative error value instead of a positive
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The index is signed, make sure it is not negative
when we read the array element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Update the nand information passed to the core from the platform data to
setup the initial option value, so that flags such as NAND_SCAN_SILENT_NODEV
can pass through.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add NAND_SCAN_SILENT_NODEV to chip->options to the user-worrying messages
'No NAND device found!!!'. This message often worries users (was three
exclamation marks really necessary?) and especially in systems such as the
Simtec Osiris where there may be optional NAND devices which are not
known until probe time.
Revised version of the original NAND_PROBE_SPECULATIVE patch after comments
by Artem Bityutskiy about adding a whole new call.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a quick and dirty patch to add panic_write for NAND flashes. The
patch seems to work OK on my CRIS board running a 2.6.26 kernel with a
ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit), and also on a
OpenRD base (Marvell Kirkwood) board with a Toshiba NAND 512MiB 3,3V
8-bit flash with 2.6.32-pre1.
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add __nand_calculate_ecc() which does not take struct mtd_info.
The built-in 256/512 software ECC calculation and correction tester
will use it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Later versions of this controller also allow 4k pagesize,
so use mtd->writesize instead of a flag.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The main/spare areas are on different addresses on later versions
of the controller, so make them configurable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The NAND controller has some limitations how to access the
internal buffers. It only allows 32 bit accesses. The driver
used to work around this by having special alignment aware
copy routines.
We now copy the whole page to a buffer in memory and let the
access functions use this buffer. This simplifies the driver.
A bonnie++ test showed that this has no negative performance
impact on the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This factors the address cycle to a seperate function. This
becomes useful in a later patch where we can simplify the
command processing by making use of this function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The oob layout was initialized several times. Instead, use
a smallpage layout by default and switch to a largepage
afterwards if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The original Freescale driver used to have eccoob descriptions like
this:
static struct nand_ecclayout nand_hw_eccoob_8 = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
.oobfree = {{0, 5}, {11, 5}}
};
static struct nand_ecclayout nand_hw_eccoob_16 = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
.oobfree = {{0, 6}, {12, 4}}
};
The former was used for 8bit flashes and the latter for 16bit flashes.
They honored the fact that the bad block marker on 8bit flashes is on byte 5
while on 16bit flashes it is on byte 11.
In the Kernel driver this was copied wrong and we ended up with two identical
descriptions.
Change it so that we have only one description which leaves byte 5 and byte
11 unspecified so that it won't be used by others.
Also, rename the descriptions to nand_hw_eccoob_smallpage and
nand_hw_eccoob_largepage so that it can't be confused with Nand chip bus
widths (what actually happened in this driver)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 71b7d0d90d.
The problem which that commit attempted to fix was a bootloader issue,
which had been misunderstood. The 'fix' causes lots of false bad blocks
for existing users with sane firmware.
Thanks to Mathieu Berland for diagnosing the problem coherently.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a request_mem_region() before doing the ioremap(). Also, use the
resource_size macro instead of doing the end - start + 1 calc by hand.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function mxcnd_remove is used only wrapped by __exit_p so define it
using __exit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vladimir Barinov <vova.barinov@gmail.com>
Cc: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Correct typo to use mask_ale from platform data when set to non-zero.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixed following htmldocs warnings:
DOCPROC Documentation/DocBook/mtdnand.xml
Warning(drivers/mtd/nand/nand_base.c:769): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:785): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:824): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:947): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:996): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:1040): No description found for parameter 'page'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to the following modules from drivers/mtd/
devices/m25p80.c
devices/slram.c
linux version 2.6.30
ftl.c
nand/cafe_nand.c
nand/cmx270_nand.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As with orion_nand in commit f33dabbe79
("register orion_nand using platform_driver_probe()"), avoid .init.text
problems by using platform_device_probe(). This isn't going to be
hotplugged anyway.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using __nand_correct_data() helper function, this driver can read 512
byte (with 6 byte ECC) at a time. This results minor performance
improvement.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver may be reading 512 bytes at a times, but still calculates
256-byte sector ECC. So the nand_correct_data() is not appropriate
for this driver. Implement its ecc.correct function calling
__nand_correct_data() twice.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Split nand_correct_data() into two part, a pure calculation function
and a wrapper for mtd interface.
The tmio_nand driver can implement its ecc.correct function easily
using this __nand_correct_data helper.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix ECC Correction bug where the byte offset location were double
fliped causing correction routine to toggle the wrong byte location
in the ECC segment. The ndfc_calculate_ecc routine change the order
of getting the ECC code.
/* The NDFC uses Smart Media (SMC) bytes order */
ecc_code[0] = p[2];
ecc_code[1] = p[1];
ecc_code[2] = p[3];
But in the Correction algorithm when calculating the byte offset
location, the b1 is used as the upper part of the address. Which
again reverse the order making the final byte offset address
location incorrect.
byte_addr = (addressbits[b1] << 4) + addressbits[b0];
The order is change to read it in straight and let the correction
function to revert it to SMC order.
Cc: stable@kernel.org
Signed-off-by: Feng Kan <fkan@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds DMA mode support for nand prefetch/post-write engine.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds prefetch support to access nand flash in mpu mode.
This patch also adds 8-bit nand support (omap_read/write_buf8).
Prefetch can be used for both 8- and 16-bit devices.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add w90p910 NAND driver for w90p910 evaluation board
based on w90p910,there is a K8F1G08 NAND on my board.
[dwmw2: depend on MTD_PARTITIONS]
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch allows i.MX27 to support 2KiB pagesize NAND flash.
We are using a 1.8V NAND flash which datasheet (unfortunately only
available under NDA) says :
Page size: x8: 2,112 bytes (2,048 + 64 bytes).
Without this patch, all sectors are marked as bad eraseblock.
Signed-off-by: Eric Benard <ebenard@eukrea.com>
Acked-by : Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds 4-bit ECC support for large page NAND chips using the new
ECC mode NAND_ECC_HW_OOB_FIRST. The platform data from board-dm355-evm
has been adjusted to use this mode.
The patches have been verified on DM355 device with 2KiB-page Micron
devices using mtd-tests and JFFS2. Error correction up to 4 bits has
also been verified using nandwrite/nanddump utilities.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2KiB) NAND
chips. This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.
"ECC_HW_OOB_FIRST" name suggested by Thomas Gleixner
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
orion_nand_probe lives in .init.text, so using platform_driver_register to
register it is wrong because binding a device after the init memory is
discarded (e.g. via sysfs) results in an oops.
As requested by Nicolas Pitre platform_driver_probe is used instead of
moving the probe function to .devinit.text as proposed initially. This
saves some memory, but devices registered after the driver is probed are
not bound (probably there are none) and binding via sysfs isn't possible.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Joern Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@marvell.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
1. <linux/io.h> should be included not <asm/io.h>
2. add platform specific header <mach/ts72xx.h>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Correcting debug prints by removing function names from print messages
and using '__func__' macro instead.
Function names were wrong in few places.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
GCC 4.3.3 and 4.4.1 happily moves the dword load instruction out of the
loop in orion_nand_read_buf. This patch makes the instruction volatile
to avoid the issue. I've discussed this at gcc-help, refer to the thread
at
http://gcc.gnu.org/ml/gcc-help/2009-08/msg00187.html
The early clobber is added to avoid the destination registers and the
source register overlapping.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
arch/arm/mach-ep93xx/include/mach/hardware.h
1. Properly name the include files so that they are loaded
from the <mach/*> directory and not the local directory.
2. Remove including the ts72xx.h header. This header is not
generic to the ep93xx platform. It should only be included
by the ts72xx specific files that require it. The only
two users in the tree are arch/arm/mach-ep93xx/ts72xx.c
and drivers/mtd/nand/ts7250.c.
arch/arm/mach-ep93xx/include/mach/ts72xx.h
1. <linux/io.h> should already be included by any user of this
header. Doing the include here hides it from being needed
by the calling source file.
arch/arm/mach-ep93xx/core.c
1. Remove unnecessary headers. They were probably included
originally due to cut-and-paste from other files.
2. <linux/io.h> should be included not <mach/gpio.h>
arch/arm/mach-ep93xx/adsphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/ts72xx.c
1. Remove unnecessary headers.
arch/arm/mach-ep93xx/ts72xx.c
1. Remove unnecessary headers.
2. Add platform specific header <mach/ts72xx.h>.
drivers/mtd/nand/ts7250.c
1. <linux/io.h> should be included not <asm/io.h>.
2. Add platform specific header <mach/ts72xx.h>.
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to include jiffies.h manually in some cases, and the status
returned from omap_wait() was broken in two separate ways.
Also add cond_resched() to the loop.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 81933046ef ('mtd: Fix handling of
mtdname in txx9ndfmc.c') introduced a potential memory leak. The
'mtdname' member of the private data structure is now allocated
separately, but was not freed on certain error paths.
Fix that, and make things simpler by _always_ allocating it separately
so that we don't need 'if (mtdname != dev_name()) kfree(mtdname);'...
which gets ugly now that we're doing it more than once, and more likely
that we'll get it wrong some time.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is not 8 times faster than byte access, but still around 60% faster.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add s3c6400 support to the s3c2410 driver. The nand controller in
the s3c64xx devices is compatible with the one in the s3c2412, so
simply reuse that code.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add code to deal with fractional lengths, as reported by
Werner Almesberger. Re-work of his original patch.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Added a flag to allow the machine code to tell the NAND
subsystem that it should try to pickup a BBT from the flash,
and also skip the NAND full scan at startup.
Signed-off-by: Michel Pollet <buserror@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
with `while (max_retries-- > 0)' max_retries reaches -1 after the loop.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the correct S3C2440_NFCONF_* macros for the mask for the 2412/2440
variants instead of the 2410 ones which use wrong bit positions.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
DaVinci clock support has been updated in mainline.
Update clock names accordingly.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver is present in the OMAP tree, now pushing it to MTD.
Original author(s):
Jian Zhang <jzhang@ti.com>
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Cc: Jian Zhang <jzhang@ti.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The DMAs have different bit sizes on BF52x and BF54x. From the PHRM:
"The 16-bit DMA Access Bus (DAB) connects the DMA controller to the
on-chip peripherals, PPI, SPI, Ethernet MAC, the SPORTs, NFC,
HOSTDP and the UARTs."
32-bit DMA won't work for BF52x.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Just add a new on-flash-bbt module parameter.
Signed-off-by: Simon Polette <spolette@adetelgroup.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Add support for 2KiB page size flashes
- Fix page address access for large pages
- Detect oob layout at runtime
- handle pagesize_2k variable
- Fix oob16 layout: reserve location 5 of oob area since it's used for bbt
Signed-off-by: Vladimir Barinov <vova.barinov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add optional callback to allow platform to initialize partitions.
Static partitions on a nand device could vary depending on the size of the
device. This patch allows an optional platform callback to be used to
setup this partition information at runtime.
Scan order is:
1) chip.part_probe_types
2) chip.set_parts
3) chip.partitions
4) full mtd device (fallback for no partitions)
Some of the existing nand drivers could possibly be replaced by the
plat_nand driver by using this patch. These include autcpu12.c and
ts7250.c drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add optional probe and remove callbacks to the plat_nand driver.
Some platforms may require additional setup, such as configuring the
memory controller, before the nand device can be accessed. This patch
provides an optional callback to handle this setup as well as a callback
to teardown the setup.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds (write|read)_buf callbacks to plat_nand.
The NAND on the TS-7800 provisioned by the FPGA allows readw() and
readl() to be used which gives a 2.5x speed up. To be able to use this
from the plat_nand driver a hook for read_buf (and also write_buf whilst
we are in there) need to be made available. This patch adds the hook.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove some legacy code from the davinci_nand driver, which made
cmdlinepart ignore the the MTD ID passed to it. Boards can have
multiple NAND chips, and some do (like the DM357 EVM), so this
dated hack is undesirable.
Correct labels are like "davinci_nand.0" (for chipselect 0).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make sure to pass the same dev_id data to free_irq() that was
used when calling request_irq(), otherwise we get a warning about
freeing an already free IRQ.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Type of 'byte_addr' needes to be 'unsigned int' for 512 byte
ECC support.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Minimal support for the 4-bit ECC engine found on DM355, DM365,
DA830/OMAP-L137, and similar recent DaVinci-family chips.
This is limited to small-page flash for now; there are some page
layout issues for large page chips. Note that most boards using
this engine (like the DM355 EVM) include 2GiB large page chips.
Sanity tested on DM355 EVM after swapping the socketed NAND for
a small-page one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make the DaVinci NAND driver require platform_data with
board-specific configuration. We can't actually do any
kind of sane job of configuring it otherwise.
Also fix the comment about picking the "best" ECC mode.
We can't do those any more; that relied on knowing what kind
of CPU we're using (they don't all support 4-bit ECC), and
current policy is that drivers not have cpu_is_*() checks.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Resolve issue noted by Sneha: when computing oobavail from
the list of free areas in the OOB, don't assume there will
always be an unused slot at the end. With ECC_HW_SYNDROME
and 4KiB page chips, it's fairly likely there *won't* be one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Narnakaje, Snehaprabha" <nsnehaprabha@ti.com>"
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With CONFIG_HOTPLUG=n, the following eror occurred during link:
local symbol 0: discarded in section `.devexit.text' from
drivers/built-in.o
It was caused by improper section reference. The __devexit_p()
should be added to the .remove function.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch allows commandline partition processing to
work with the s3c2410 NAND platform driver.
Signed-off-by: Andy Green <andy@warcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: Change andy@openmoko.com to andy@warmcat.com]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix NAND CFG debug order.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: Change andy@openmoko.com to andy@warmcat.com, subject cleanup]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
~ Avoid warning without generating code.
(I don't even get the warning without the macro uninitialized_var).
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: subject cleanup]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This makes us take note about the chosen ECC mode per-chip and
not the one set globally.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: andy@openmoko.com => andy@warmcat.com, rewrite subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 57fee4a58f added an
method to specify the platform device compatibility by using
an id-table instead of registering multiple drivers.
Move the S3C24XX NAND driver to using this ID table.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CC: Eric Miao <eric.miao@marvell.com>
As pointed out by Kay Sievers, the name size limit is gone
from the driver-core, and BUS_ID_SIZE is obsolescent.
Rather than just papering over the problem by replacing the mtdname
array size with an arbitrary '20 + 2', fix the problem properly and
handle arbitrary name sizes.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The following patch fixes:
- re-initialization of host->col_addr which is used as byte index
between the successive READID flash commands.
- compile error when CONFIG_PM is enabled
- pass on the error code from clk_get()
- return -ENOMEM in case of failed ioremap()
- pass on the return value of platform_driver_probe() directly
- remove excessive printk
- let command line partition table parsing with mxc_nand name.
The cmd_line parsing is done via <mtd-id> name that differs
from mxc_nand by default and looks like "NAND 256MiB 1,8V 8-bit"
Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now the MTD core will do this for us, we don't need to hook it up from
the board drivers.
Shame we can't do shutdown from the class too...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern. The TQM8548_BE requires a further short delay
after writing out a buffer. Normally the R/B pin should be checked, but
it's not connected on the TQM8548_BE. The existing driver uses similar
fixed delay points. To manage these extra delays in a more general way,
I introduced the "fsl,ump-wait-flags" property allowing the board-
specific driver to specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. This requires support for multiple GPIOs for the RNB pins.
The NAND chips are selected through address lines defined by the
FDT property "fsl,upm-addr-line-cs-offsets".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
module: use strstarts()
strstarts: helper function for !strncmp(str, prefix, strlen(prefix))
arm: allow usage of string functions in linux/string.h
module: don't use stop_machine on module load
module: create a request_module_nowait()
module: include other structures in module version check
module: remove the SHF_ALLOC flag on the __versions section.
module: clarify the force-loading taint message.
module: Export symbols needed for Ksplice
Ksplice: Add functions for walking kallsyms symbols
module: remove module_text_address()
module: __module_address
module: Make find_symbol return a struct kernel_symbol
kernel/module.c: fix an unused goto label
param: fix charp parameters set via sysfs
Fix trivial conflicts in kernel/extable.c manually.
Follow-on patch to the previous driver model patch for the MTD
framework. This one makes various MTD drivers connect to the
driver model tree, so /sys/devices/virtual/mtd/* nodes are no
longer present ... mostly drivers used on boards I have handy.
Based on a patch from Kay Sievers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A pointer to plat_nand_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Hamish Moffatt <hamish@cloud.net.au>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Impact: Replace and remove risky (non-EXPORTed) API
module_text_address() returns a pointer to the module, which given locking
improvements in module.c, is useless except to test for NULL:
1) If the module can't go away, use __module_text_address.
2) Otherwise, just use is_module_text_address().
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There is no need to have a "\n" on a MODULE_DESCRIPTION, remove it.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
This patch fixes the bug reported in
http://bugzilla.kernel.org/show_bug.cgi?id=11681.
"Lots of device drivers register a 'struct device_driver' with
the '.bus' member set to '&platform_bus_type'. This is wrong,
since the platform_bus functions expect the 'struct device_driver'
to be wrapped up in a 'struct platform_driver' which provides
some additional callbacks (like suspend_late, resume_early).
The effect may be that platform_suspend_late() uses bogus data
outside the device_driver struct as a pointer pointer to the
device driver's suspend_late() function or other hard to
reproduce failures."(Lothar Wassmann)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the integrated NAND flash controller of the
TXx9 family.
Once upon a time there were tx4925ndfmc and tx4938ndfmc driver. They
were removed due to bitrot in 2005.
This new driver is completely rewritten based on a driver in CELF patch
archive.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Bächle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move mtd_has_partitions() and mtd_has_cmdlinepart() inlines from a
DaVinci-specific driver to the <linux/mtd/partitions.h> header.
Use those to eliminate #ifdefs in two drivers which had their own
definitions of mtd_has_partitions().
Quite a lot of other MTD drivers could benefit from using use one or both
of these to remove #ifdeffery. Maybe some Janitors would like to help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Usage of davinci-specific cpu_is macros is not allowed in drivers.
These options should be passed in through platform_data.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix incorrect debug messages (*write* not read); someone committed some
cut'n'paste bugs. There might be more, I only noticed these since I was
looking for nand_read usage and landed in some very wrong functions.
IMO all MTD debugging message framework is goofed, anyway. It uses
"DEBUG" in a way that's incompatible with usage most everywhere else in
the kernel, and which prevents normal pr_dbg() and dev_dbg() calls from
working right.
[True. It predates those by a long way, and should probably be updated
to use them. dwmw2]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a device driver for the NAND flash controller found on the various
DaVinci family chips. It handles up to four SoC chipselects, and some
flavors of secondary chipselect (e.g. based on upper bits of the address
bus) as used with some multichip packages. (Including the 2 GiB chips
used on some TI devel boards.)
The 1-bit ECC hardware is supported (3 bytes ECC per 512 bytes data); but
not yet the newer 4-bit ECC (10 bytes ECC per 512 bytes data), as
available on chips like the DM355 or OMAP-L137 and needed with the more
error-prone MLC NAND chips.
This is a cleaned-up version of code that's been in use for several years
now; sanity checked with the new drivers/mtd/tests.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The syndrome based page read/write routines store ECC, and possibly other
"OOB" data, right after each chunk of ECC'd data. With ECC chunk size of
512 bytes and a large page (2KiB) NAND, the layout is:
data-0 OOB-0 data-1 OOB-1 data-2 OOB-2 data-3 OOB-3 OOB-leftover
Where OOBx is (prepad, ECC, postpad). However, the current "raw" routines
use a traditional layout -- data OOB, disregarding the prepad and postpad
values -- so when they're used with that type of ECC hardware, those calls
mix up the data and OOB. Which means, in particular, that bad block
tables won't be found on startup, with data corruption and related chaos
ensuing.
The current syndrome-based drivers in mainline all seem to use one chunk
per page; presumably they haven't noticed such bugs.
Fix this, by adding read/write page_raw_syndrome() routines as siblings of
the existing non-raw routines; "raw" just means to bypass the ECC
computations, not change data and OOB layout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The bf5xx_nand_add_partition() func is only called by __devinit functions,
so put it into the __devinit section as well
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Only set DMAC1_PERIMUX once we have requested and been granted the dma
channel to prevent breaking other peripherals in the error case
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The context makes it clear already that these are clocks, so there's
no need for such a suffix. This patch only changes the clocks actually
used in the tree. The remaining clocks are renamed in the subsequent
architecture specific patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The definitions of PXA_CS<x>_PHYS are really PXA2xx specific and should
be moved out of pxa-regs.h. As an illustration, the PXA3xx static chip
selects definitions are added into pxa3xx-regs.h.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
X86_PC is the only remaining 'sub' architecture, so we dont need
it anymore.
This also cleans up a few spurious references to X86_PC in the
driver space - those certainly should be X86.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
X86_GENERICARCH is a misnomer - it contains non-PC 32-bit architectures
that are not included in the default build.
Rename it to X86_32_NON_STANDARD.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[dwmw2: updated and made to still register whole device first]
Signed-off-by: Philip Rakity <pakity@yahoo.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The current ndfc driver only compiles under arch/ppc. This arch was
removed from the kernel. I notice the event entry for the ndfc in
Kconfig has been removed in 2.6.28.
This patch converts the ndfc to a proper OF (OpenFirmware) driver. I
can give a working example of the DTS if needed.
The patch has been in production use on the PIKA Warp Appliance and is
in use by others. The Warp basically boots from NAND, so the ndfc driver
is very important to us.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-By: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The various fields in NDTR{01} are in units of clock ticks minus one, but the
ns2cycle macro mistakenly adds one, inflating the number of clock ticks and
making it impossible to set any of these fields to zero.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Reads from non-page-aligned addresses were broken because while the
address to read from was correctly written to NDCB*, a full page was
always read. Fix this by ignoring the column and only using the page
address.
I suspect this whole-page behavior is due to the controller's need to
read the entire page in order to generate correct ECC. In the non-ECC
case this could be optimized to use the column address, and to set the
read length to what is being requested rather than the length of an
entire page.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix sched.h references:
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: dereferencing pointer to incomplete type
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: 'PF_MEMALLOC' undeclared (first use in this function)
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1328: error: dereferencing pointer to incomplete type
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: dereferencing pointer to incomplete type
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: 'PF_MEMALLOC' undeclared (first use in this function)
build-r7149.out:make[4]: *** [drivers/mtd/nand/nandsim.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ECCM maybe set in bootloader, Get ECCM settings from the bootloader,
can avoid the image written by bootloader cannot read out by kernel.
But the limitation of doing it this way is that, it could break large page
NAND if it is written with NAND disabled in u-boot and read with NAND
enabled, or vice versa.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Delete extra kernel-doc notation for struct fields and function
parameters that don't exist:
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'wq' description in 'nand_chip'
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'datbuf' description in 'nand_chip'
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'oobbuf' description in 'nand_chip'
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'oobdirty' description in 'nand_chip'
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'data_poi' description in 'nand_chip'
Warning(drivers/mtd/nand/nand_base.c:2527): Excess function parameter 'maxchips' description in 'nand_scan_tail'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD internal API presently uses 32-bit values to represent
device size. This patch updates them to 64-bits but leaves
the external API unchanged. Extending the external API
is a separate issue for several reasons. First, no one
needs it at the moment. Secondly, whether the implementation
is done with IOCTLs, sysfs or both is still debated. Thirdly
external API changes require the internal API to be accepted
first.
Note that although the MTD API will be able to support 64-bit
device sizes, existing drivers do not and are not required
to do so, although NAND base has been updated.
In general, changing from 32-bit to 64-bit values cause little
or no changes to the majority of the code with the following
exceptions:
- printk message formats
- division and modulus of 64-bit values
- NAND base support
- 32-bit local variables used by mtdpart and mtdconcat
- naughtily assuming one structure maps to another
in MEMERASE ioctl
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Nandsim consumes ~2x more RAM than the density of simulated device.
It becomes critical if we need to simulate 256MB NAND and run stress tests
on it.
We investigated the reasons. nandsim allocates space for pages using kmalloc
function. The size of LP nand page is 2112 bytes.
kmalloc gets space from slab pools by chunks 2^n. So if we need to kmalloc
2112 bytes, 4096 bytes will be consumed by system.
The best way to avoid this issue would be using kmem_cache allocations. AFAIK
this mechanism specially designed to handle cases when arrays of allocations
are used.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a new module parameter 'cache_file' which causes nandsim
to use that file instead of memory to cache nand data.
Using a file allows the simulation of NAND that is bigger
than the available memory.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
nand_base sometimes reads only 2 bytes of a 4 byte id.
It is OK. Do not print a warning in that case.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
STM 2Gb flash is a large-page NAND flash. Set operations accordingly.
This field is dereferenced without a check in several places resulting in
OOPS.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Eric Miao <ymiao3@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
pci_get_device increments a reference count that should be decremented
using pci_dev_put.
The semantic patch that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S,S1;
position p1,p2,p3;
expression E,E1;
type T,T1;
expression *ptr != NULL;
@@
(
if ((x@p1 = pci_get_device(...)) == NULL) S
|
x@p1 = pci_get_device(...);
)
... when != pci_dev_put(...,(T)x,...)
when != if (...) { <+... pci_dev_put(...,(T)x,...) ...+> }
when != true x == NULL || ...
when != x = E
when != E = (T)x
when any
(
if (x == NULL || ...) S1
|
if@p2 (...) {
... when != pci_dev_put(...,(T1)x,...)
when != if (...) { <+... pci_dev_put(...,(T1)x,...) ...+> }
when != x = E1
when != E1 = (T1)x
(
return \(0\|<+...x...+>\|ptr\);
|
return@p3 ...;
)
}
)
@ script:python @
p1 << r.p1;
p3 << r.p3;
@@
print "* file: %s pci_get_device: %s return: %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton, remove memzero() - it's not supported
on other architectures so use of it is a potential build breaking bug.
Since the compiler optimizes memset(x,0,n) to __memzero() perfectly
well, we don't miss out on the underlying benefits of memzero().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch fixes following build error:
CC drivers/mtd/nand/fsl_upm.o
drivers/mtd/nand/fsl_upm.c: In function 'fun_chip_init':
drivers/mtd/nand/fsl_upm.c:168: warning: passing argument 2 of 'of_mtd_parse_partitions' from incompatible pointer type
drivers/mtd/nand/fsl_upm.c:168: warning: passing argument 3 of 'of_mtd_parse_partitions' from incompatible pointer type
drivers/mtd/nand/fsl_upm.c:168: error: too many arguments to function 'of_mtd_parse_partitions'
make[1]: *** [drivers/mtd/nand/fsl_upm.o] Error 1
The breakage was introduced in 69fd3a8d09
("[MTD] remove unused mtd parameter in of_mtd_parse_partitions()").
While at it, also add a check for the of_mtd_parse_partitions() return
value.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Finally move registration of sharpsl-nand device to board-specific code.
sharpsl nand driver is now clean and simple.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Merge mtd_info and nand_chip info special struct and
make it drvdata instead of plain static variable.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Start cleanup of sharpsl_nand driver. Convert it to platform driver.
Corresponding device is temprorary registered in sharpsl.c but will be
later moved to corresponding board files.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
* git://git.infradead.org/mtd-2.6: (69 commits)
Revert "[MTD] m25p80.c code cleanup"
[MTD] [NAND] GPIO driver depends on ARM... for now.
[MTD] [NAND] sh_flctl: fix compile error
[MTD] [NOR] AT49BV6416 has swapped erase regions
[MTD] [NAND] GPIO NAND flash driver
[MTD] cmdlineparts documentation change - explain where mtd-id comes from
[MTD] cfi_cmdset_0002.c: Add Macronix CFI V1.0 TopBottom detection
[MTD] [NAND] Fix compilation warnings in drivers/mtd/nand/cs553x_nand.c
[JFFS2] Write buffer offset adjustment for NOR-ECC (Sibley) flash
[MTD] mtdoops: Fix a bug where block may not be erased
[MTD] mtdoops: Add a magic number to logged kernel oops
[MTD] mtdoops: Fix an off by one error
[JFFS2] Correct parameter names of jffs2_compress() in comments
[MTD] [NAND] sh_flctl: add support for Renesas SuperH FLCTL
[MTD] [NAND] Bug on atmel_nand HW ECC : OOB info not correctly written
[MTD] [MAPS] Remove unused variable after ROM API cleanup.
[MTD] m25p80.c extended jedec support (v2)
[MTD] remove unused mtd parameter in of_mtd_parse_partitions()
[MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGE
[MTD] [NAND] driver extension to support NAND on TQM85xx modules
...
Not all architectures provide readsb(). We should probably move to using
ioread8_rep() instead.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix compile error because the first patch was broken -- the file got
truncated.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch adds support for NAND flashes connected to GPIOs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates most of the OMAP drivers which are in mainline to switch to
using the cross-platform GPIO calls instead of the older OMAP-specific
ones.
This is all fairly brainless/obvious stuff. Probably the most interesting
bit is to observe that the omap-keypad code seems to now have a portable
core that could work with non-OMAP matrix keypads. (That would improve
with hardware IRQ debouncing enabled, of course...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several Renesas SuperH CPU has FLCTL. The FLCTL support NAND Flash.
This driver support SH7723.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The functions that write the OOB info (on hardware ECC only) use the
HW_SYNDROME method.
This is not correct : the start position is "pos = eccsize + chunk" and
should be eccsize. So, the standard (nand_write_oob_std) function should
be used. This patch corrects this by using NAND_ECC_HW instead of
NAND_ECC_HW_SYNDROME.
This has only been tested on small pages nand flash.
(if anyone can test it on large pages that would be great).
kernel version : 2.6.27-rc2 (current git mtd-2.6)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Removed the Kconfig associated with 'NDFC NanD Flash Controller'.
We can't enable !CONFIG_PPC_MERGE so there is no way to enable
this. Additionally the code needs to get updated for arch/powerpc.
For the time being lets just remove the Kconfig option so we can
actually remove CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch extends the FSL UPM NAND driver from Anton Vorontsov to
support hardware which does not have the R/B pin of the NAND chip
connected, like the TQM8548 module:
- The OF_GPIO dependency has been removed from the Kconfig option
because GPIO is not needed. The relevant gpio_* function are then
stubbed out in <linux/gpio.h>.
- It re-introduces the chip-delay property to define an appropriate
maximum delay time (tR) required for read operations. The binding
will be documented in a separate patch.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Get rid of fsl,wait-pattern and fsl,wait-write. I think this isn't
chip-specific, and we should always do waits. I saw one board that
didn't need fsl,wait-pattern, but I assume this was the exception
that proves the rule;
- Get rid of chip-delay. Today there are no users for this, and if
anyone really need this they should push the OF bindings beforehand;
- Now flash chips should be child nodes of the FSL UPM NAND controller;
- Implement OF partition parsing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add copyright information for some of the AT91 header files.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix offset of second word used for programming base address of memory
window. Also program tmio with offset of the FCR, not with physical
memory location.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the integrated NAND flash controller of the
i.MX2 and i.MX3 family. It is tested on MX27 but should work on MX3
aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Minor patch to help debugging of NAND detection.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves some attributes out from the platform data into the
dynamically created nand device. This results into a cleaner interface
and allows to use constant pxa3xx_nand_flash definitions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch marks some attributes as 'const' which are set only once and
never be modified by the driver. There are some changes in parameter
list and variable declarations too which mark them as 'const'.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a MTD_NAND_PXA3xx_BUILTIN configuration variables which
allows to disable usage of builtin flash-type table. Not enabling this
option saves some space in the generated driver.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds 'flash' and 'num_flash' attributes to the platform data.
There was added code in the driver to iterate across these attributes in the
detect-flash routine. This is done similarly to the existing method
which uses a 'builtin_flash_types' field.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves the exported datastructures from the pxa3xx_nand.c driver
into the <mach/pxa3xx_nand.h> header. This is a plain movement without
any modification of the attributes.
This is the first one of a set of patches which:
* allows to specify used NAND flash in the platform code and allows to turn
off the old way to specify NAND characteristics in the driver. This way did
not worked well as these characteristics depend on the platform and can not be
derived from NAND id alone.
E.g. some NAND chips share the same ID (e.g. K9K8G08U0A and K9NBG08U5A) but
have different timings (which are written in the common driver currently and
must be modified there).
* adds 'const' annotations at various places
Further patches will be sent to the mtd-list.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Semun Lee <semun.lee@samsung.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It doesn't use LINUX_VERSION_CODE nor KERNEL_VERSION.
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch for nand_ecc.c fixes three issues
- fix code so it also works on big endian architectures
- added a printk in case of an uncorrectable ecc error
- strengthen the test for correctable errors (decreasing the chance
that multiple bit faults by accident will be seen as correctable)
Note: the big endian code is only tested in a testbed (running on big endian
hardware) as I cannot rebuild and test a big endian kernel at the moment.
However the only thing that can go wrong is if <asm/byteorder.h> does not
give __BIG_ENDIAN in that case. In my eyes very unlikely.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
This patch improves the performance of the ecc generation code by a
factor of 18 on an INTEL D920 CPU, a factor of 7 on MIPS and a factor of 5
on ARM (NSLU2)
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Removed duplicated include <asm/div64.h> in
drivers/mtd/nand/nandsim.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The TMIO chips are only found (and thus tested) on ARM machines.
Moreover, we don't want the TMIO cells to be built if one of the TMIO
driver is not selected (which indirectly make the TMIO cells drivers
depend on ARM as well).
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the NAND controller commonly found in
TMIO based MFDs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This was a reference board for which support never got merged upstream.
Kill it off, at rmk's suggestion.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/nandsim.c: In function 'divide':
drivers/mtd/nand/nandsim.c:462: error: implicit declaration of function 'do_div'
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/fsl_elbc_nand.c:890: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 3d45955962 ("subpage read feature
as a way to improve performance") broke nandsim because nandsim does not
support the "random page read" NAND command. This patch adds
corresponding support.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch enables NAND subpage read functionality.
If upper layer drivers are requesting to read non page aligned data NAND
subpage-read functionality reads the only whose ECC regions which include
requested data when original code reads whole page.
This significantly improves performance in many cases.
Here are some digits :
UBI volume mount time
No subpage reads: 5.75 seconds
Subpage read patch: 2.42 seconds
Open/stat time for files on JFFS2 volume:
No subpage read 0m 5.36s
Subpage read 0m 2.88s
Signed-off-by Alexey Korolev <akorolev@infradead.org>
Acked-by: Artem Bityutskiy <dedekind@infradead.org>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for CPU frequency scalling to the S3C24XX NAND driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With CONFIG_MTD_OF_PARTS=y I'm getting this new section mismatch in reference
from the function fsl_elbc_chip_probe() to the function
.devinit.text:of_mtd_parse_partitions()
This patch fixes the mismatch by providing __devinit annotation to the
fsl_elbc_chip_probe() function.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Such a hardcoded address can cause a checkstop or machine check if
the driver is in the kernel but the address is not acknowledged.
Both drivers allow an address to be specified as either a module
parameter or config option. Any future powerpc board should either
use one of these methods or find the address in the device tree.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Also remove mtd->ecclayout and mtd->oobavail assignments, mtd core
handles this all by itself.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There's no reason to prevent the Atmel NAND driver from
building as a module.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ALE signal isn't correctly wired up to the ECC controller on the
AP7000, so it starts calculating ECC during the address cycles.
Work around this by resetting the ECC controller between the address and
data cycles.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This uses __raw_{read,write}s{b,w}() primitives to access data on NAND
chips for more efficient I/O.
On an arm926 with memory clocked at 100 MHz, this reduced the elapsed time
for a 64 MiB read by 16%. ("dd" /dev/mtd0 to /dev/null, with an 8-bit
NAND using hardware ECC and 128KiB blocksize.)
Also some minor section tweaks:
- Use platform_driver_probe() so no pointer to probe() lingers
after that code has been removed at run-time.
- Use __exit and __exit_p so the remove() code will normally be
removed by the linker.
Since these buffer read/write calls are new, this increases the runtime
code footprint (by 88 bytes on my build, after the section tweaks).
[haavard.skinnemoen@atmel.com: rebase onto atmel_nand rename]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Update CM-X270 NAND flash driver to use gpio_lib.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some SoCs need a different chip_delay value.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Make the atmel_nand driver selectable on AVR32, and update the Kconfig
help text to reflect this.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This fixes several bugs in the atmel_nand_probe() error path, including
at least one memory leak.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The AT91 NAND driver needs just a few tiny modifications to work on
AVR32 as well. Rename it atmel_nand to reflect this.
Also move the ECC register definitions into drivers/mtd/nand since they
are only useful to the atmel_nand driver, and get rid of the useless
filename at the top of each file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
No point in using an AT91-specific GPIO API when the generic API works
just as well.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
WARNING: drivers/mtd/nand/built-in.o(.devinit.text+0x114): Section mismatch
in reference from the function fsl_elbc_ctrl_probe() to the function
.devexit.text:fsl_elbc_ctrl_remove()
__devinit functions should not call functions with __devexit. Since probe
function calls remove in case of errors, we want to remove __devexit
attribute from it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix nandsim build error, missing #include:
linux-next-20080605/drivers/mtd/nand/nandsim.c: In function 'divide':
linux-next-20080605/drivers/mtd/nand/nandsim.c:462: error: implicit declaration of function 'do_div'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The changelog on the driver is superflous given this
is being kept under revision control. Remove the other
cruft in the header and update the copyright and the
supported device list.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a minor problem with what should have been
debug output by changing printk() to dev_dbg()
inside s3c2410_nand_update_chip().
Thanks to David Woodhouse for pointing this out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Amend nandsim so that it does not assume 32-bit flash size.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use at91_nand_enable(), at91_nand_disable() to manipulate enable_pin.
No functional changes.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This driver did not control NCE signal during normal operations (only
enable NCE on probing and disable NCE on removing). This patch make
NCE signal inactive on idle state.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The sam926x docs allegedly don't list an "ECC_PARITY" field, and the
header files in the upstream kernel don't have it either.
Masking with it was useless anyway, so just remove it.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is a patch to use the hardware ECC controller of
the AT91SAM9260 and AT91SAM9263 for the AT91 nand.
On AT91 NAND, there's now a choice between ECC soft,
ECC hard or no ECC (for debug).
It has been tested on AT91SAM9263 with 8 bits large
and small page NAND.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
With modern systems using bus-hold instead of bus pull-up, it can
often lead to erroneous reporting of NAND devices where there are
none. Do a double probe to ensure that the result we got the first
time is repeatable, and if it is not then return that there is no
chip there.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support to disable ECC checking for a given chip
when passed by the board via the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for the ECC layout to be passed via the
platform data specified by the board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If a block's ecc field is all 0xff, then ignore the ECC
correction. This is for systems where some of the blocks,
such as the initial cramfs are written without ECC and
need to be loaded on start.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This adds support for using large page NAND devices
with the S3C24XX NAND controller. This also adds the
file Documentation/arm/Samsung-S3C24XX/NAND.txt to
describe the differences.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Commit 03680b1e00 incorrectly
was assuming S3C2410_NFCONF was being used to select the
NAND chip. Fix this error by ising the sel_reg.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch sets mtd->name to the platform bus ID in the plat_nand
driver, so that you can specify partitions readily with mtdparts=.
Currently it relies on nand_base filling in the name from the device,
which results in names like "NAND 256MiB 3,3V 8-bit", that you can't
use with cmdlineparts.
Signed-off-by: Hamish Moffatt <hamish@cloud.net.au>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a race condition in fsl_elbc_run_command
Fix incorrect usage of clearbits32 that bashed option register
Remove work around for bashed register
Signed-off-by: Mike Hench <mhench@elutions.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently fsl_elbc_nand doesn't initialize mtd->name, and this causes
nand_get_flash_type() to assign name that is equal to chip type, like
this:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "NAND 32MiB 3,3V 8-bit"
mtd0 is physmap_of flash (normal name), and mtd1 is fsl_elbc_nand.
Despite inconsistency, with mtd name like this specifying paritions
from the kernel command line becomes a torture (though, I didn't tried
and not sure if mtdparts= can handle spaces at all). Plus, this causes
real bugs when multiple fsl_elbc_nand chips registered.
With this patch applied fsl_elbc_nand chip will have proper name:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "e0600000.flash"
p.s. We can't use priv->dev->bus_id as in physmap_of, because
fsl_elbc_nand pretends to be a localbus controller, so its bus_id is
"address.localbus", which is incorrect and thus will also not work
for multiple chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is very simple driver, NAND is connected through localbus,
and User-Programmable Machine is doing various adjustments to
speak NAND. No special efforts needed to do read and write cycles,
though to control ALE and CLE phases, we ask UPM to generate exact
pre-programmed signals on the localbus lines.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is preliminary since:
1. It supports only _one_ chip select at the moment. As there is no
existing platforms available using two chip selects of the NAND
controller, it shall really not include code for supporting the
2nd chip select for now, as such code cannot be verified.
2. It resorts to the default and simpliest memory based badblock
table
3. Only limited types of nand flash are currently supported. Most
PXA3xx processors come with on-chip NAND flash dies, so there
isn't much flexibility for other types of NAND.
4. The NAND controller should be configured to detect the device's
ID, thus making it difficult to use nand_scan_ident() to assist
the detection process (though it's not impossible)
TODO: fix all the above limitations of cuz :-)
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Previously, a READ command was erroneously issued rather than SEQIN.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The part_probes[] should be static.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MTD NAND
platform drivers, to re-enable auto loading.
NOTE: at91_nand for some reason disallows modular builds. I'm assuming that's
just an oversight that will be fixed.
[dbrownell@users.sourceforge.net: minor fix]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I found this while I was looking how the rs_lib is working. The rs_decoder is
initialized _after_ the nand core code read the BBT table and _after_ the
partition table has been added. The driver has a private BBT description
which is in located in flash data so we Ooops if there is a bit flip _or_ if a
bit flips while reading the partition table.
This patch moves the initialization of the rs_lib before the first possible
access by nand core.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jörn Engel <joern@wh.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make the needlessly global part_probes[] static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
This is needed to support other localbus peripherals, such as
NAND on FSL UPM.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This has been forgotten in commit f5bbdacc41 ("[MTD] NAND Modularize
read function") and nobody compiled the driver.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joern Engel <joern@wh.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implements kernel command line partitioning support for the CS5535/CS5536 chipsets driver.
For that the following is done:
* cs553x_cleanup(): try the cleanup for all chip selects to not leak memory
* Assign a unique name for each chip select to be separately addressable in the command line mtd-id portion(s)
* Use the already defined PIN_OPT_IDE constant where appropriate for readability
* Include command line partitioning support when CONFIG_MTD_PARTS is set
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* git://git.infradead.org/mtd-2.6: (120 commits)
[MTD] Fix mtdoops.c compilation
[MTD] [NOR] fix startup lock when using multiple nor flash chips
[MTD] [DOC200x] eccbuf is statically defined and always evaluate to true
[MTD] Fix maps/physmap.c compilation with CONFIG_PM
[MTD] onenand: Add panic_write function to the onenand driver
[MTD] mtdoops: Use the panic_write function when present
[MTD] Add mtd panic_write function pointer
[MTD] [NAND] Freescale enhanced Local Bus Controller FCM NAND support.
[MTD] physmap.c: Add support for multiple resources
[MTD] [NAND] Fix misparenthesization introduced by commit 78b65179...
[MTD] [NAND] Fix Blackfin NFC ECC calculating bug with page size 512 bytes
[MTD] [NAND] Remove wrong operation in PM function of the BF54x NFC driver
[MTD] [NAND] Remove unused variable in plat_nand_remove
[MTD] Unlocking all Intel flash that is locked on power up.
[MTD] [NAND] at91_nand: Make mtdparts option can override board info
[MTD] mtdoops: Various minor cleanups
[MTD] mtdoops: Ensure sequential write to the buffer
[MTD] mtdoops: Perform write operations in a workqueue
[MTD] mtdoops: Add further error return code checking
[MTD] [NOR] Test devtype, not definition in flash_probe(), drivers/mtd/devices/lart.c
...
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is no suspend/resume operation in NFC driver at all, currently.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
With CONFIG_MTD_PARTITIONS not set, got this:
drivers/mtd/nand/plat_nand.c:113: warning: unused variable 'pdata'
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Call parse_mtd_partitions before checking board's partition_info, so
that "mtdparts=" option can override board's default setting.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The single-bit error correction was, well, incorrect. For determing which
bit to correct it was using P1' P2' P4' P8' instead of P1 P2 P4 P8, and
it was using P16' P32' P64' P128' P256' P512' P1024' P2048' instead of
P16 P32 P64 P128 P256 P512 P1024 P2048.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If there were multiple bit errors in the data s3c2410_nand_correct_data()
was returning 0 (no error) instead of -1, so the upper layers (like JFFS2)
would not know the data is corrupt.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Some hardware, such as the enhanced local bus controller used on some
mpc83xx chips, does ecc transparently when reading and writing data, rather
than providing a generic calculate/correct mechanism that can be exported to
the nand subsystem.
The subsystem should not BUG() when calculate, correct, or hwctl are
missing, if the methods that call them have been overridden.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Driver for the device bus NAND controller in the Marvell Orion family
of ARM SoCs.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Plumbing for NAND connected via localbus on PA Semi PWRficient-based
boards.
From: Egor Martovetsky <egor@pasemi.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ensure the nFCE line is de-asserted over suspend and
then re-initialised when the system resumes. This is
to ensure that the NAND is kept in lowest power mode
over suspend (power settings are only specified for
nFCE inactive) as well as fixing the Simtec Osiris
which relies on nFCE being inactive.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Magic numerical values are just bad style. Particularly so when
undocumented.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Treat any negative return value from a NAND driver's correct() function
as a failure, rather than just -1.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
NAND of > 32MiB in size use 4 bytes in address cycle, not 3.
Reported-by: bhsong <bhsong@augustatek.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add read_buf/write_buf for s3c2440, which can read/write 32 bits at a
time rather than just 8. In my testing on an s3c2440a running at 400 MHz
with a 100 MHz HCLK, read performance improves by 36% (from 5.19 MB/s
to 7.07 MB/s).
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the driver for latest Blackfin on-chip nand flash controller
- use nand_chip and mtd_info common nand driver interface
- provide both PIO and dma operation
- compiled with ezkit bf548 configuration
- use hardware 1-bit ECC
- tested with YAFFS2 and can mount YAFFS2 filesystem as rootfs
ChangeLog from try#1
- use hweight32() instead of count_bits()
- replace bf54x with bf5xx and BF54X with BF5XX
- compare against plat->page_size in 2 cases when enable hardware ECC
ChangeLog from try#2
- passed nand_test suites
- use cpu_relax() instead of busy wait loop
- some coding style issue pointed out by Andrew
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/alauda.c: In function 'alauda_bounce_read':
drivers/mtd/nand/alauda.c:412: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When the erase callback performs some other action on the flash, it's
highly likely to deadlock unless we actually release the chip lock
before calling it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Originally from Marcelo; modified to put the original timing registers
back instead of 0xFFFFFFFF.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
It was only the very early prototypes which made the mistake of using
the same device ident for all three functions on the device -- don't
bother trying to express that in the PCI match table, since the tools
don't cope. We can check in the probe routine instead, just in case.
Also remember to terminate the table.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixup the includes which have been moved around
when changing the s3c24xx arch support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make nandsim use GFP_NOFS when allocating memory, because it might
be used by a file-system (e.g. UBIFS2) which means, if we are short
of memory, we may deadlock. Indee, UBIFS is holding a lock, writes
to the media, reaches this place in NANDsim, kmalloc does not find
the requested amount of RAM, calls memory shrinker, which decides
to writeback inodes, calls FS, and it deadlocks on the lock which
is already being held. Below is the UBIFS backtrace which
demonstrates that:
[<c03717dc>] __mutex_lock_slowpath+0xc8/0x2e6
[<c0371a16>] mutex_lock+0x1c/0x1f
[<f8b9d076>] reserve_space+0x3d/0xa9 [ubifs]
[<f8b9d1bd>] make_one_reservation+0x2b/0x86 [ubifs]
[<f8b9d3fc>] ubifs_jrn_write_block+0xda/0x12f [ubifs]
[<f8b9ff3a>] ubifs_writepage+0x11d/0x1ec [ubifs]
[<c015d6ab>] shrink_inactive_list+0x7fa/0x969
[<c015d8c8>] shrink_zone+0xae/0x10c
[<c015e3b4>] try_to_free_pages+0x159/0x251
[<c015980a>] __alloc_pages+0x125/0x2f0
[<c016ff6a>] cache_alloc_refill+0x380/0x6ba
[<c01703f3>] __kmalloc+0x14f/0x157
[<f885722a>] do_state_action+0xab7/0xc74 [nandsim]
[<f885760c>] switch_state+0x225/0x402 [nandsim]
[<f8857e7e>] ns_hwcontrol+0x3e2/0x620 [nandsim]
[<f8862f53>] nand_command+0x2e/0x1a5 [nand]
[<f8861ad8>] nand_write_page+0x4a/0x9a [nand]
[<f88617b4>] nand_do_write_ops+0x1cf/0x343 [nand]
[<f8861a70>] nand_write+0x88/0xa6 [nand]
[<f8850b0e>] part_write+0x72/0x8b [mtd]
[<f88e19c5>] ubi_io_write+0x189/0x29c [ubi]
[<f88dfb98>] ubi_eba_write_leb+0xb6/0x699 [ubi]
[<f88def93>] ubi_leb_write+0xe4/0xe9 [ubi]
[<f8ba3b82>] ubifs_wbuf_write_nolock+0x333/0x4c9 [ubifs]
[<f8b9d28c>] write_node+0x74/0x8e [ubifs]
[<f8b9d422>] ubifs_jrn_write_block+0x100/0x12f [ubifs]
[<f8b9ff3a>] ubifs_writepage+0x11d/0x1ec [ubifs]
[<c0159e5b>] __writepage+0xb/0x26
[<c015a318>] write_cache_pages+0x203/0x2d9
[<c015a411>] generic_writepages+0x23/0x2d
[<c015a452>] do_writepages+0x37/0x39
[<c018e24a>] __writeback_single_inode+0x96/0x399
[<c018e903>] sync_sb_inodes+0x1a3/0x274
[<c018ebf3>] writeback_inodes+0xa6/0xd8
[<c015a9dd>] background_writeout+0x86/0x9e
[<c015ae9c>] pdflush+0xfb/0x1b6
[<c01387d7>] kthread+0x37/0x59
[<c0104dc3>] kernel_thread_helper+0x7/0x14
The deadlock is funny because it starts in pdflush/writeback,
and comes back to writeback, then deadlocks. It seems we should look
carefully for other places in UBI and MTD and use GFP_NOFS instead
of GFP_KERNEL.
Caught-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Unlike most stuff on the market the chip inside these two allows raw
flash access and doesn't implement and FTL, leaving that functionality
to the device driver.
Raw flash access in a cheap USB cardreader! An MTD test device one can
attach to a PC! What a deal!
The command set of the chip is not documented, so information was
obtained from the existing mass-storage driver
(drivers/usb/storage/alauda.c), its documentation
(http://alauda.sourceforge.net/wikka.php?wakka=BulkCommandReference),
additional reverse engineering and comparison with a vendor driver for a
related chip
(http://www.ratocsystems.com/english/download/driver/linux/sma03u.html).
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
These drivers are specific to 4xx support in arch/ppc at the moment. Make
sure they don't get built on arch/powerpc.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The nand_base.c driver implicitly casts the uint32_t
eccpos array to 'int *', which is not only not guaranteed
to be the same sign as the source, but is not guaranteed
to be the same size.
Fix by changing nand_base.c to use uint32_t
referencing the eccpos fields.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below fixes nand driver for AT91 boards which do not have NAND
R/B signal connected to gpio (rdy_pin is not connected).
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we mark block bad we have to get chip because this involves
writing to the page's OOB. We hit this bug in UBI - we observed
random obscure crashes when it marks block bad from the background
thread and there is some parallel task which utilizes flash.
This patch also adds a TODO note about BBT table protection which
it seems does not exist.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch ensures that the current code (kernel 2.6.22) uses the bits
like the code prior to the refactoring. The variable "bits" is employed
in a useful way now.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
replace with working link from nand Kconfig help text
fixes bugzilla 7815
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we mark block bad we have to get chip because this involves
writing to the page's OOB. We hit this bug in UBI - we observed
random obscure crashes when it marks block bad from the background
thread and there is some parallel task which utilizes flash.
This patch also adds a TODO note about BBT table protection which
it seems does not exist.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch ensures that the current code (kernel 2.6.22) uses the bits
like the code prior to the refactoring. The variable "bits" is employed
in a useful way now.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch cleans up duplicate includes in
drivers/mtd/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds the manufacturer ID for AMD flash.
Signed-off-by: Steven J. Hill <sjhill1@rockwellcollins.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch has removed Ocelot G support from MTD.
Ocelot G support has already removed since May 2007.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The price might drop to $100 in a few years.
But currently, a more reasonable name might be "$175 laptop".
Let's simply call it "OLPC laptop" without any price tag.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds 405 platform support to the 440 NDFC driver. The new
AMCC 405EZ PPC is equipped with the same NDFC core as the 440EP(x)
and other will follow soon.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The nand_base.c driver implicitly casts the uint32_t
eccpos array to 'int *', which is not only not guaranteed
to be the same sign as the source, but is not guaranteed
to be the same size.
Fix by changing nand_base.c to use uint32_t
referencing the eccpos fields.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below fixes nand driver for AT91 boards which do not have NAND
R/B signal connected to gpio (rdy_pin is not connected).
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix various bits of obviously-busted code which we're not happening to
compile, due to ifdefs.
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jan Kara <jack@ucw.cz>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have made a tool to parse the kernel that does not pre-process the
source. That means that my parser tries to parse all the code, including
code in the #else branch or code that is not often compiled because the
driver is not very used (or not used at all). So, my parser sometimes
reports parse error not originally detected by gcc. Here is my (first)
patch.
[akpm@linux-foundation.org: fix amd8111e.c]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (21 commits)
[MTD] [CHIPS] Remove MTD_OBSOLETE_CHIPS (jedec, amd_flash, sharp)
[MTD] Delete allegedly obsolete "bank_size" field of mtd_info.
[MTD] Remove unnecessary user space check from mtd.h.
[MTD] [MAPS] Remove flash maps for no longer supported 405LP boards
[MTD] [MAPS] Fix missing printk() parameter in physmap_of.c MTD driver
[MTD] [NAND] platform NAND driver: add driver
[MTD] [NAND] platform NAND driver: update header
[JFFS2] Simplify and clean up jffs2_add_tn_to_tree() some more.
[JFFS2] Remove another bogus optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remove broken insert_point optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remember to calculate overlap on nodes which replace older nodes
[JFFS2] Don't advance c->wbuf_ofs to next eraseblock after wbuf flush
[MTD] [NAND] at91_nand.c: CMDLINE_PARTS support
[MTD] [NAND] Tidy up handling of page number in nand_block_bad()
[MTD] block2mtd_paramline[] mustn't be __initdata
[MTD] [NAND] Support multiple chips in CAFÉ driver
[MTD] [NAND] Rename cafe.c to cafe_nand.c and remove the multi-obj magic
[MTD] [NAND] Use rslib for CAFÉ ECC
[RSLIB] Support non-canonical GF representations
[JFFS2] Remove dead file histo_mips.h
...
This patch adds support for generic platform NAND driver.
Updated after tglx's review/discussion in IRC #mtd channel.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch allows you to specify at91_nand partitions on the
kernel command line using the mtdparts variable, if
CONFIG_MTD_CMDLINE_PARTS is set.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Further to the previous patch fixing the calculation of page number,
both branches are using the same result. Clean up the function
accordingly, calculating it (and also masking with pagemask) only in one
place.
Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The CAFÉ can handle two chip on separate chipselect lines. Hook up the
undocumented chipselect bits in the driver and probe both.
In the case of OLPC, it's not actually two separate devices -- it's a
single '1GiB' package with two 512MiB dies internally. So clear the
NAND_BBT_PERCHIP flag to treat it as a single chip for BBT purposes, and
make life easier for the firmware.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch provides MTD support for NAND flash devices on CM-x270 modules.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In case that there is no memory based bad block table available the
function nand_block_checkbad() in drivers/mtd/nand/nand_base.c will call
nand_block_bad() directly. When parameter 'getchip' is set to zero,
nand_block_bad() will not right shift the offset to calculate the
correct page number.
Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A new module parameter has been added called 'overridesize',
which overrides the size that would be determined by the
ID bytes. 'overridesize' is specified in erase blocks and
as the exponent of a power of two e.g. 5 means a size of
32 erase blocks.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A new module parameter 'rptwear' specifies how many erases between
reporting wear information. Zero means never.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
New module parameters have been added to nandsim to
simulate:
bitflips random bit flips
badblocks blocks that are initially marked bad
weakblocks blocks that fail to erase after a
small number of erase cycles
weakpages pages that fail to write after a
small number of successful writes
gravepages pages that fail to read after a
small number of successful reads
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Enhance nandsim to be able to create more than 1 partition.
A new module parameter 'parts' may be used to specify partition
sizes.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is a slight bug in nand_default_block_markbad, where the offset is
cast to an integer, prior to being shifted. This means that on large
offsets, it is incorrectly doing a signed shift & losing bits. Fixed
this by doing the cast after the shift (as is done elsewhere in the code).
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use the functions in the ecc structure instead of the default ones,
so the override by the board driver is effective also for software ecc
code paths.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Replace the apparently misspelled preprocessor variable
"MTD_NAND_DISKONCHIP_BBTWRITE" with the correct form
"CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
During the MTD rework the oobavail parameter of mtd_info structure has become
private. This is not quite correct in terms of integrity and logic. If we have
means to write to OOB area, then we'd like to know upfront how many bytes out
of OOB are spare per page to be able to adapt to specific cases.
The patch inlined adds the public oobavail parameter.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Noticed while building a s3c2410 kernel :
drivers/mtd/nand/s3c2410.c: In function 's3c2440_nand_calculate_ecc':
drivers/mtd/nand/s3c2410.c:476: warning: format '%06x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
This patch fixes it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2412 use differents registers than s3c2440 for hw ecc handling.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.fr>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/cafe.c: In function 'cafe_nand_cmdfunc':
drivers/mtd/nand/cafe.c:269: warning: 'irqs' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal. Fixup the remaining users in -mm.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a nand flash driver for the eXcite series of intelligent
cameras manufactured by Basler Vision Technologies AG.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for correcting errors detected by the
hardware ECC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Remove unused and broken mtd->ecctype and mtd->eccsize fields
from struct mtd_info. Do not remove them from userspace API
data structures (don't want to breake userspace) but mark them
as obsolete by a comment. Any userspace program which uses them
should be half-broken anyway, so this is more about saving
data structure size.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
err_pos_lut[4096] of an array with 4096 elements is a bug.
Spotted by the Coverity checker.
While I was at it, I also converted it to ARRAY_SIZE().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add checks to ensure that out-of-band reads and writes are
not attempted with an invalid offset or length. Specifically,
the offset must be less than the size of oob for a page
and the length must not go beyond the size of the device.
Additionally the checks must adjust for auto-placement
(MTD_OOB_AUTO) of oob data.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The precise timings are board-specific (or NAND chip specific) and don't
belong here. If they're set already, then use what we find there.
Otherwise, revert to the most conservative default values (and whinge).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for 16-bit NAND bus-width for the AT91 NAND driver.
The 16-bit NAND is found on the Atmel AT91SAM9260-EK and AT91SAM9261-EK
boards.
Orignal Patch from Patrice Vilchez
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Number of address bytes for 64-128 MiB NANDs is 4, not 5.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Select MTD_NAND_ECC_SMC (ECC byte order according to the Smart Media
Specification) if MTD_NAND_NDFC is used.
Using the wrong byte order causes fatal, unnoticed data damage.
For further information see:
http://lists.infradead.org/pipermail/linux-mtd/2006-November/016920.html
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The newly-added cafe_ecc.c had a lot of it because of the way the lookup
table was auto-generated; clean up the other files too while we're at it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix up the config option in the #ifdef statements in nand_ecc.c
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As was discussed between Ricard Wanderlöf, David Woodhouse, Artem
Bityutskiy and me, the current API for reading/writing OOB is confusing.
The thing that introduces confusion is the need to specify ops.len
together with ops.ooblen for reads/writes that concern only OOB not data
area. So, ops.len is overloaded: when ops.datbuf != NULL it serves to
specify the length of the data read, and when ops.datbuf == NULL, it
serves to specify the full OOB read length.
The patch inlined below is the slightly updated version of the previous
patch serving the same purpose, but with the new Artem's comments taken
into account.
Artem, BTW, thanks a lot for your valuable input!
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The writel() call accidentally clears all bits in the NDFC_CCR
register (endianess problem). Now __raw_writel() is used instead.
Tested on Bamboo with NAND on chip select 0 and chip select 1.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch converts drivers/mtd/nand/rtc_from4.c to use the new
lib/bitrev.c
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We were resetting cafe->ctl2 to zero after an erase (and also during a
write, but it was correctly reset after that). This meant that ECC reads
after an erase were failing. Doh.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Also use cafe_readl() and cafe_writel() abstraction to make code
slightly cleaner -- especially if we want to use it in PIO mode.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add description of 'raw' in comments for
drivers/mtd/nand/nand_base.c::nand_write_page_syndrome() so 'make xmldocs'
will not spew a warning at us.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Being a value which isn't in the table is a case we explicitly check for
in the caller. Don't BUG_ON() because it does actually happen in
practice.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When a flash-based BBT is not used, nand_default_mark_blockbad() is supposed
to mark the block bad in the oob. However, it sets the wrong length variable
so that no bad block marker is in fact written. This patch attempts to
rectify that.
(As note, it seems to be that logically, it shouldn't be necessary to set
both length variables, as one appears to be for the main buffer, and
one for the oob buffer, but this is how it is done in several places,
including the code for the mtd character device MEMWRITEOOB and MEMREADOOB
ioctls. I'm not sure if this is a temporary solution during some rework of
the mtd infrastructure, or whether there is a deeper thought here.)
Signed-off-by: Ricard Wanderlöf <ricardw@axis.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ditch the separate oobrbuf and oobwbuf fields from the chip buffers,
and use only a single buffer immediately after the data. This accommodates
NAND controllers such as the OLPC CAFÉ chip, which can't do scatter/gather
DMA so needs the OOB buffer to be contiguous with the data, for both read
and write.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As flash cannot do 0->1 bit transitions when programming, do not do this in
the simulator too. This makes nandsim able to accept subpage writes.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Removes line break after return type in function definitions, to be
consistent with the Linux coding style.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For page wise allocation, an array of flash page pointers is allocated
during initialization. The flash pages are themselves allocated when a
write occurs to the page. The flash pages are deallocated when they
are erased.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch removes code that does chip mapping. The chip mapping code
is no longer used.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This version only differs from version posted by Savin Zlobec (20 Jun
2006) in that the AT91RM9200-specific chip-select / bus setup code has
been moved from the at91_nand.c driver into the processor-specific file.
From: Savin Zlobec <savin@epico.si>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Updated version of patch, in response to comments from Francois Romieu
<romieu@fr.zoreil.com>
Remove gratuitous casts from iounmap and initialisation of variables.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- allow high-level nand_write_page() function to be overridden
- likewise low-level write_page_raw() and read_page_raw() functions
- Clean up the abuse of chip->ecc.{write,read}_page() with MTD_OOB_RAW
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Due to this typo, a wrong ECC layout table is chosen.
Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only) with:
- allmodconfig
- Modifying drivers/mtd/maps/Kconfig and drivers/mtd/nand/Kconfig to
make sure that the changed file is compiling without warning
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The recent hwctrl core conversion for MTD NAND devices broke the Amstrad
Delta driver. This fixes it up and uses the existing control line defines
rather than unclear magic numbers.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Read the return value before we release the nand device otherwise the
value can become corrupted by another user of chip->ops, ultimately
resulting in filesystem corruption.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CNE bits are inverted on the device and writeb function is missing a
NOT operation.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In the case of data-pad-ecc-pad-data... layout the oob start position
has to be sizeof(data) in nand_write_oob_syndrom().
In nand_fill_oob() we need to copy to buf + buffer offset instead of
buf + write offset.
From: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix all kernel-doc warnings in MTD headers and source files:
- add some missing struct fields;
- correct some function parameter names;
- use kernel-doc format for function doc. headers;
- nand_ecc.c contains only exported interfaces, no internal ones;
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The other way round works not really well with boards which have a
static NAND chipselect.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I was unable to compile ts7250.c after your refactor commit,
it's a typo probably.
-- ynezz
From: Petr Stetiar <ynezz@true.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for both the S3C2412 and S3C2412 Samsung SoCs to
the increasingly mis-named s3c2410.c driver.
This currently only supports SLC ECCs, and a chip on nFCE0.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The rework of the command handling in the nand driver
led to wrong address setting in the command control
function. Use the correct address again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert the use of printk() to the correct dev_info/dev_err
functions
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The oob fixups broke a return value and missed one patch from
the Mailing List.
Signed-off-by: Savin Zlobec <savin@epico.si>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Following problems are addressed:
- wrong status caused early break out of nand_wait()
- removed the bogus status check in nand_wait() which
is a relict of the abandoned support for interrupted
erase.
- status check moved to the correct place in read_oob
- oob support for syndrom based ecc with strange layouts
- use given offset in the AUTOOOB based oob operations
Partially based on a patch from Vitaly Vool <vwool@ru.mvista.com>
Thanks to Savin Zlobec <savin@epico.si> for tracking down the
status problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In nand_read_page_syndrome/nand_write_page_syndrome the calculation of
the remaining oob length which is not used by the prepad/ecc/postpad
areas is wrong.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix unused variables and commenting since tglx's
new NAND updates
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/nand_base.c: In function 'nand_transfer_oob':
drivers/mtd/nand/nand_base.c:909: warning: comparison of distinct pointer types lacks a cast
drivers/mtd/nand/nand_base.c: In function 'nand_do_read_oob':
drivers/mtd/nand/nand_base.c:1097: error: 'len' undeclared (first use in this function)
drivers/mtd/nand/nand_base.c:1097: error: (Each undeclared identifier is reported only once
drivers/mtd/nand/nand_base.c:1097: error: for each function it appears in.)
drivers/mtd/nand/nand_base.c: In function 'nand_fill_oob':
drivers/mtd/nand/nand_base.c:1411: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The raw read/write access to NAND (without ECC) has been changed in the
NAND rework. Expose the new way - setting the file mode via ioctl - to
userspace. Also allow to read out the ecc statistics information so userspace
tools can see that bitflips happened and whether errors where correctable
or not. Also expose the number of bad blocks for the partition, so nandwrite
can check if the data fits into the parition before writing to it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Return -EUCLEAN on read when a bitflip was detected and corrected, so the
clients can react and eventually copy the affected block to a spare one.
Make all in kernel users aware of the change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hopefully the last iteration on this!
The handling of out of band data on NAND was accompanied by tons of fruitless
discussions and halfarsed patches to make it work for a particular
problem. Sufficiently annoyed by I all those "I know it better" mails and the
resonable amount of discarded "it solves my problem" patches, I finally decided
to go for the big rework. After removing the _ecc variants of mtd read/write
functions the solution to satisfy the various requirements was to refactor the
read/write _oob functions in mtd.
The major change is that read/write_oob now takes a pointer to an operation
descriptor structure "struct mtd_oob_ops".instead of having a function with at
least seven arguments.
read/write_oob which should probably renamed to a more descriptive name, can do
the following tasks:
- read/write out of band data
- read/write data content and out of band data
- read/write raw data content and out of band data (ecc disabled)
struct mtd_oob_ops has a mode field, which determines the oob handling mode.
Aside of the MTD_OOB_RAW mode, which is intended to be especially for
diagnostic purposes and some internal functions e.g. bad block table creation,
the other two modes are for mtd clients:
MTD_OOB_PLACE puts/gets the given oob data exactly to/from the place which is
described by the ooboffs and ooblen fields of the mtd_oob_ops strcuture. It's
up to the caller to make sure that the byte positions are not used by the ECC
placement algorithms.
MTD_OOB_AUTO puts/gets the given oob data automaticaly to/from the places in
the out of band area which are described by the oobfree tuples in the ecclayout
data structre which is associated to the devicee.
The decision whether data plus oob or oob only handling is done depends on the
setting of the datbuf member of the data structure. When datbuf == NULL then
the internal read/write_oob functions are selected, otherwise the read/write
data routines are invoked.
Tested on a few platforms with all variants. Please be aware of possible
regressions for your particular device / application scenario
Disclaimer: Any whining will be ignored from those who just contributed "hot
air blurb" and never sat down to tackle the underlying problem of the mess in
the NAND driver grown over time and the big chunk of work to fix up the
existing users. The problem was not the holiness of the existing MTD
interfaces. The problems was the lack of time to go for the big overhaul. It's
easy to add more mess to the existing one, but it takes alot of effort to go
for a real solution.
Improvements and bugfixes are welcome!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand_oobinfo structure is not fitting the newer error correction
demands anymore. Replace it by struct nand_ecclayout and fixup the users
all over the place. Keep the nand_oobinfo based ioctl for user space
compability reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The info structure for out of band data was copied into
the mtd structure. Make it a pointer and remove the ability
to set it from userspace. The position of ecc bytes is
defined by the hardware and should not be changed by software.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The platform structure was lacking an oobinfo field.
The NDFC driver had some remains from another tree.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have a type pointer. Make use of it instead of the error prone nand_ids[i]
reference.
The NAND driver used to set default name settings from the chip ID
string for the device. The feature got lost during the rework. Add it back.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
nCE setting can be done when the first command is issued to the device.
We keep the deselect functionality as it makes sense to deassert nCE
when the device becomes idle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Modularize the write function and reorganaize the internal buffer
management. Remove obsolete chip options and fixup all affected
users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
PCI is faked on these devices by SMM traps. Don't depend on that --
check for the chipset directly instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Split the core of the read function out and implement
seperate handling functions for software and hardware
ECC.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand driver has a superflous read ready / command
delay in the read functions. This was added to handle
chips which have an automatic read forward. Newer
chips do not have this functionality anymore. Add this
option to avoid the delay / I/O operation. Mark all
large page chips with the new option flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The lock simplifying patch did not move the lock and waitqueue
initialization into the controller allocation patch.
This reinitializes waitqueue and spinlocks also for driver
supplied controller stuctures. Move it into the allocation path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The previous change of the command / hardware control allows to
remove the write_byte/word functions completely, as their only
user were nand_command and nand_command_lp.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The hwcontrol function enforced a step by step state machine
for any kind of hardware chip access. Let the hardware driver
know which control bits are set and inform it about a change
of the control lines. Let the hardware driver write out the
command and address bytes directly. This gives a peformance
advantage for address bus controlled chips and simplifies the
quirks in the hardware drivers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
MTD clients are agnostic of FLASH which needs ECC suppport.
Remove the functions and fixup the callers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
First step of modularizing ECC support.
- Move ECC related functionality into a seperate embedded data structure
- Get rid of the hardware dependend constants to simplify new ECC models
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Seperate functionality out of nand_scan so the code is more
readable. No functional change. First step of simplifying
the nand driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The NAND driver used a mix of unsigned char, u_char amd uint8_t
data types. Consolidate to uint8_t usage
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace the chip lock by a the controller lock. For simple drivers a
dummy controller structure is created by the scan code.
This simplifies the locking algorithm in nand_get/release_chip().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unrolling the loops produces denser and much faster code.
Add a config switch which allows to select the byte order of the
resulting ecc code. The current Linux implementation has a byte
swap versus the SmartMedia specification
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
o Add a flag MTD_BIT_WRITEABLE for devices that allow single bits to be
cleared.
o Replace MTD_PROGRAM_REGIONS with a cleared MTD_BIT_WRITEABLE flag for
STMicro and Intel Sibley flashes with internal ECC. Those flashes
disallow clearing of single bits, unlike regular NOR flashes, so the
new flag models their behaviour better.
o Remove MTD_ECC. After the STMicro/Sibley merge, this flag is only set
and never checked.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
At least two flashes exists that have the concept of a minimum write unit,
similar to NAND pages, but no other NAND characteristics. Therefore, rename
the minimum write unit to "writesize" for all flashes, including NAND.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
The patch below adds support for the NAND device on the Amstrad Delta.
This is a 32MiB 8bit Toshiba device, with the data bus connected to the
OMAP MPUIO pins and ALE, CLE, NCE, NRE, NWE and NWP all connected to the
Delta's latch2 16bit latch.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
On AMD Au1550 the static bus controller fails to keep -CE asserted during
chip ready delay on read commands and the NAND chip being used requires this.
So, the current driver allows nand_base.c to drive -CE manually during the
entire sector read. When the PCMCIA driver is enabled however, occasionally
the ECC errors occur on NAND reads. This happens because the PCMCIA driver
polls sockets periodically and reads one of the board's control/status regs
(BCSRs) which are on the same static bus as the NAND flash, and just use
another chip select (and the NOR flash also resides on that bus), so as the
NAND driver forces NAND chip select asserted and the -RE signal is shared, a
contention occurs on the static bus when BCSR or NOR flash is read while we're
reading from NAND.
So, we either can't keep interrupts enabled during the whole NAND sector
read (which is hardly acceptable), or have to implement some interlocking
scheme between multiple drivers (which is painful, and makes me shudder :-).
There's a third way which has proven to work: to force -CE asserted only
while we're waiting for a NAND chip to become ready after a read command,
disabling interrupts for a maximum of 25 microseconds (according to Toshiba
TC58DVM92A1FT00 datasheet -- this chip is mentioned in the board schematics);
for Samsung NAND chip which seems to be actually used this delay is even less,
12 us.
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
During the last cleanup of the AMD Au1550 NAND driver the old buglet was
reintroduced: as the MEM_STNDCTL register is write-only and seem to always
read as 0x31, read-modify-write to it done in au1xxx_nand_init() will have the
side effect of enabling -RCS0/1 pin override (via bits 4/5 of this reg.), thus
possibly causing a contention on the static bus when the NOR flash (using
-RCS0) or board control status registers (using -RCS2) are read. Luckily, this
goes away with a first NAND access, since au1550_hwcontrol() doesn't try to
read this register before writing anymore.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We all inherited the same error from the original NAND board driver which
got copied and changed. Fix them all at once...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make it work even with compilers which lack the wit to notice that
THIS_MODULE is always non-NULL. Use #ifdef MODULE instead. It's only
a temporary debugging check anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The _board_ driver needs to be mtd->owner, and it in turn pins the
nand.ko module. Fix them all to actually do that, and fix nand.ko not to
overwrite it -- and also to check that the caller sets it, if the caller
is a module.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We were scanning for 0xFF through the entire chip -- which takes a while
when it's a 512MiB device as I have on my current toy. The specs only say
we need to check certain bytes -- so do only that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- Implement HW ECC support,
- Provide read_buf() and write_buf() routines using memcpy
- Use on-flash bad block table
- Fix module refcounting
- Avoid read/modify/write in hwcontrol()
- Minor cosmetic fixes
Partly based on code and ideas from Tom Sylla <tom.sylla@amd.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This lacks hardware ECC support and a few optimisations we're going to
want fairly soon, but it works well enough to mount and use JFFS2.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The TS-72xx is a series of embedded single board computers from
Technologic Systems based on the Cirrus ep93xx (arm920t based) CPU.
The TS-7200 uses NOR flash, while all the other models in the series
(TS-7250, TS-7260) use NAND flash -- included is a driver for the NAND
flash on those boards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MTD_NAND=m and MTD_NAND_SHARPSL=y or MTD_NAND_NANDSIM=y are illegal
combinations that mustn't be allowed.
This patch fixes this bug by making MTD_NAND_SHARPSL and MTD_NAND_NANDSIM
tristate's.
Additionally, it fixes some whitespace damage at these options.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: "Artem B. Bityutskiy" <dedekind@yandex.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains the following possible cleanups:
- every file should #include the headers containing the prototypes for
it's global functions
- make needlessly global functions static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
__ioremap is an architecture private interface and must not be used
by drivers when the architecture independent interface will do just
as well. Switch the ipaq drivers to use the correct interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/mtd part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/mtd/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nathan Roberts noticed the nand_write_ecc index into oobbuf goes out of
bounds when crossing an erase block boundary, causing incorrect OOB data
to be written and corrupting memory. Reset the index to zero after
re-preparing oobbuf for a new erase block.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In case of an odd offset, the result was shifted by 1 instead of 8
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Sharp Zaurus akita and borzoi models are large page flash devices.
This patch adds support for them to the sharpsl MTD NAND driver but
keeps the oob layout and bad block positions compatible with the Sharp
Zaurus 2.4 kernel and ROM bootloader.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added owner fields to the device_driver for tracking
ownership when built as a module
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- cleaned up the partitions and include files
- added more flexible CS and address detection and setup
Regression tested on db1200 and db1550.
Signed-off-by: Pete Popov <ppopov@pacbell.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The changes introduced allow to suspend/resume NAND flash.
A new state (FL_PM_SUSPENDED) is introduced, as well as
routines for mtd->suspend and mtd->resume to put the flash in
suspended state from software pov.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The bit mask used for oob size calculation was using 2 bits instead
of one. Fortunately the next bit has been 0 all the time.
Thanks to Nathan H. for pointing this out
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add partition definitions for the new Sharp Zaurus models Spitz (SL-C3000),
Akita (SL-C1000) and Borzoi (SL-C3100)
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new kernel debug feature: CONFIG_DETECT_SOFTLOCKUP.
When enabled then per-CPU watchdog threads are started, which try to run
once per second. If they get delayed for more than 10 seconds then a
callback from the timer interrupt detects this condition and prints out a
warning message and a stack dump (once per lockup incident). The feature
is otherwise non-intrusive, it doesnt try to unlock the box in any way, it
only gets the debug info out, automatically, and on all CPUs affected by
the lockup.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The previous change to read a single byte from oob breaks the
bad block scan on 16 bit devices, when the byte is on an odd
address. Read the complete oob for now.
Remove the unused arguments from check_short_pattern()
Move the wait for ready function so it is only executed when
consecutive reads happen.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix OOPs if there was no platform set information passed
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The drivers are unmaintained since long and reference include files
which are not available in the kernel. Original author is not longer
responsible and no new maintainer showed up within 3 month.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix error in timing generation, Tacls is only in the range 0..3
Add proper support for the s3c2440 NAND controller, which has now
been tested on several s3c2440 implementations.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The code was wrong in several aspects. The locking order was
inconsistent, the device aquire code did not reset a variable
after a wakeup and the wakeup handling was not working for
applications where multiple chips are sharing a single
hardware controller.
When a hardware controller is available the locking is now
reduced to the hardware controller lock and the waitqueue is
moved to the hardware controller structure in order to avoid
a wake_up_all().
The problem was pointed out by Ben Dooks, who also found the
missing variable reset as main cause for his deadlock problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reverting the change from 1.136 to 1.137 (back to static allocation of ecc
arrays) due to stack corruption and ecc errors.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add helpful comment about oobfree so I can't claim two years from
now that I don't remember what I was thinking.
Signed-off-by: Dan Brown <dan_brown@ieee.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Try not to break existing jffs2 installs, instead break oobfree into
two out-of-order pieces.
Signed-off-by: Dan Brown <dan_brown@ieee.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Version 1.137 broke nand_read_ecc clients who pass NULL oobsel. Fixed.
Signed-off-by: Dan Brown <dan_brown@ieee.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the new NAND_SKIP_BBT option instead of defining a fake scan_bbt
handler.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Updated with tglx's suggestion to simply the command invocation by
simply changing the address of the IO write area
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace msleep by cond_resched. On machines with HZ=100 (e.g. ARM)
msleep slows down the operation by factor 10
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Check timeout while we wait for the command to finish. No worry about a
false result. This prevents deadlocking when detecting an unknown number
of chips and is useful for removable media too.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Do not use the ready function here, as it might hang for ever.
The result will show, whether the chip is there or not
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix sparse errors due to lack of address-space markers
Updated header comments
Small re-format of initialiser
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Scan 1st and 2nd pages of SP devices for BB marker by default.
Fix more then one page scanning in create_bbt.c.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move manufacturer ID search to display correct ID in case of buswidth
mismatch.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When scanning NAND for bad blocks, don't read the whole page, read
only needed OOB bytes instead. Also check the return code of the
nand_read_raw() function. Correctly free the this->bbt array in
case of failure. Tested with Large page NAND.
Fix debugging message.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Small bugfix. Sometimes it may be handy not to have bbt.
So, this->bbt might be NULL.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added routine to perform extra error status checks on erase and write
failures to determine if errors are correctable.
Added option to prevent JFFS2 from using virtual erase blocks.
Performed minor cleanup on whitespace and comments.
Signed-off-by: David A. Marlin <dmarlin@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add optional hardware specific callback routine to perform extra error
status checks on erase and write failures for devices with hardware ECC.
Signed-off-by: David A. Marlin <dmarlin@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add routine to perform device recovery (deplete) procedure.
Clean up some compiler warnings.
Signed-off-by: David A. Marlin <dmarlin@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added workaround for Renesas AG-AND chips "disturb" issue
for Bad Block Table.
Added support for the device recovery command sequence
for Renesas AG-AND chips.
Signed-off-by: David A. Marlin <dmarlin@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added extended commands for AG-AND device and added
option for BBT_AUTO_REFRESH.
Signed-off-by: David A. Marlin <dmarlin@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
