Both OneNAND and raw NAND bits can't be compiled if MTD is disabled
because of the if/endif logic in drivers/mtd/Kconfig. There is no need
for an extra "depends on MTD" in their respective Kconfig files.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529002517.3546-12-miquel.raynal@bootlin.com
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl7TdZMACgkQJWrqGEe9
VoRthQgAttWsImXpEUa8C8CXvPhjpb6uZ7QYM4PSE0bheuVi7ivoDPyYWopno30h
R6UntGbsBqPyvDFDUxUEvyvn5F0JQK1dLif+7X0Ki5on6LkYdEuanHaSMZmSIXD8
atNhLVO1FeD3EulN8Dw9hGy6OrNT8O2bESbiJrCpOk9s6yAPINhKqZVJsyShcTs5
tc94/J0DIF7og8cdH4wYoz+AWw0WaHvPsn5VWnTy08gk7dB7hsq/DeftZmrJLL0g
B7Et1pvcLBSNBGBpzS6rEjXb/e3+wdKnNy0AQvrMdEZUzN3h9aY5sCLSFOsFfKQ+
xjxJgmyoKk0C9uCeNaPt8c7gTgAZAA==
=Gz6y
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core changes:
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
NAND ECC modes (or providers) have their own enumeration but, unlike
their algorithms counterpart, there is no invalid or uninitialized
value to discriminate between an error and having chosen a no-ECC
situation. Add an "invalid" entry for this purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-7-miquel.raynal@bootlin.com
This scheme has been introduced for the Davinci controller and means
that the OOB area must be read *before* the rest of the data. This has
nothing to do with the ECC in OOB placement as it could be understood
and most importantly, there is no point in having this function out of
the Davinci NAND controller driver. A DT property for this scheme has
been added but never used, even by the Davinci driver which only uses
this scheme to change the default nand_read_page().
Move the main read_page() helper into the Davinci driver and remove
the remaining boilerplate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-4-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Now that all drivers have been converted to do not use nand_release()
anymore, let's remove this helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-63-miquel.raynal@bootlin.com
nand_release() basically calls mtd_device_unregister() and
nand_cleanup(). Both helpers should be called after MTD device
registration and NAND scan, respectively. Drop nand_release() and use
the two helpers directly so that they fit the error path and the
labels there.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-12-miquel.raynal@bootlin.com
ns_free() is the helper that is called symmetrically to ns_init() and
so should free the same objects, including the partition names.
Now, callers of ns_free() do not need to free this partition names
themselves.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-11-miquel.raynal@bootlin.com
Many function calls are done this way:
if ((retval = func()) != 0)
return retval;
while we expect in the kernel function calls like:
retval = func();
if (retval)
return retval;
Apply this change where possible and also use "ret" instead of
"retval" in ns_init_module for consistency, as it is only used in this
function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-5-miquel.raynal@bootlin.com
Some functions are prefixed "nandsim_", others "ns_" and many are
simply not prefixed at all. Make this file consistent by prefixing all
functions by "ns_".
This is a mechanical change. Sometimes the line is a bit reworked as
well to fit the kernel coding style. For instance, there are several
places where displayed strings are cut. When one of this line is
changed because of the naming update, the two parts of the strings
gets concatenated.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-4-miquel.raynal@bootlin.com
Only v3.3-v5.0 have a different CS0 layout.
Controllers before v3.3 use the same layout for every CS.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-3-noltari@gmail.com
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522104008.28340-1-dinghao.liu@zju.edu.cn
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522095139.19653-1-dinghao.liu@zju.edu.cn
Let's convert the driver to exec_op() to have one less driver relying
on the legacy interface.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519232454.374081-4-boris.brezillon@collabora.com
The rb-gpios semantics was undocumented and qi,lb60 (along with the
ingenic driver) got it wrong. The active state encodes the NAND ready
state, which is high level. Since there's no signal inverter on this
board, it should be active-high. Let's fix that here for older DTs so
we can re-use the generic nand_gpio_waitrdy() helper, and be consistent
with what other drivers do.
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519232454.374081-3-boris.brezillon@collabora.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-62-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-61-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-60-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-59-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-58-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-57-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-56-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-55-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Christophe Kerello <christophe.kerello@st.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-53-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-52-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-51-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-50-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-49-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-48-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-47-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-46-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-45-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-44-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible, hence pointing it as the commit to
fix for backporting purposes, even if this commit is not introducing
any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-43-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-42-miquel.raynal@bootlin.com
nand_cleanup() is supposed to be called on error after a successful
call to nand_scan() to free all NAND resources.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible, hence pointing it as the commit to
fix for backporting purposes, even if this commit is not introducing
any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-41-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-40-miquel.raynal@bootlin.com
On error, the oxnas probe path just frees the device which failed and
aborts the probe, leaving unreleased resources.
Fix this situation by calling mtd_device_unregister()/nand_cleanup()
on these.
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-38-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
While at it, be consistent and move the function call in the error
path thanks to a goto statement.
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-37-miquel.raynal@bootlin.com
All initialized and registered devices should be listed somewhere so
that we can unregister/free them in the _remove() path.
This patch is not a fix per-se but is needed to apply three other
fixes coming right after, explaining the Fixes/Cc: stable tags.
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-36-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-35-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-34-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-33-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-32-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-31-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-30-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-29-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-28-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-27-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-26-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-25-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-24-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-23-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. Hence, pointing it as the commit to
fix for backporting purposes, even if this commit is not introducing
any bug makes sense.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-22-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-21-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-20-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-19-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-18-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-17-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-16-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-15-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-14-miquel.raynal@bootlin.com
Not sure nand_cleanup() is the right function to call here but in any
case it is not nand_release(). Indeed, even a comment says that
calling nand_release() is a bit of a hack as there is no MTD device to
unregister. So switch to nand_cleanup() for now and drop this
comment.
There is no Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if it did not intruce
any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-13-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-12-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-10-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-9-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-7-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-6-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-5-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-4-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-3-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-2-miquel.raynal@bootlin.com
Add support for the hardware ECC BCH engine.
Please mind that this engine has an important limitation:
BCH implementation does not inform the user when an uncorrectable ECC
error occurs. To workaround this, we avoid using the hardware engine
in the read path and do the computation with the software BCH
implementation, which is faster than mixing hardware (for correction)
and software (for verification).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519074549.23673-9-miquel.raynal@bootlin.com
Add the Arasan NAND controller driver. This brings only NAND
controller support. The ECC engine being a bit subtle, hardware ECC
support will be added in a second time.
This work is based on contributions from Naga Sureshkumar Relli.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519074549.23673-8-miquel.raynal@bootlin.com
There are cases where ECC bytes are not byte-aligned. Indeed, BCH
implies using a number of ECC bits, which are not always a multiple of
8. We then need a helper like nand_extract_bits() to extract these
syndromes from a buffer.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519074549.23673-5-miquel.raynal@bootlin.com
The main NAND read page function can loop over "page reads" many times
in if the reading reports uncorrectable error(s) and if the chip
supports the read_retry feature.
In this case, the number of bitflips is summarized between
attempts. Fix this by re-initializing the entire mtd_ecc_stats object
each time we retry.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519074549.23673-4-miquel.raynal@bootlin.com
It seems that several hardware ECC engine use a swapped representation
of bytes compared to software. This might having to do with how the
ECC engine is wired to the NAND controller or the order the bits are
passed to the hardware BCH logic.
This means that when the software BCH engine is working in conjunction
with data generated with hardware, sometimes we might need to swap the
bits inside bytes, eg:
0x0A = b0000_1010 -> b0101_0000 = 0x50
Make it possible by adding a boolean to the BCH initialization routine.
Regarding the implementation itself, this is a rather simple approach
that can probably be enhanced in the future by preparing the
->a_{mod,pow}_tab tables with the swapping in mind.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519074549.23673-3-miquel.raynal@bootlin.com
There are four exported functions, all suffixed by _bch, which is
clearly not the norm. Let's rename them by prefixing them with bch_
instead.
This is a mechanical change:
init_bch -> bch_init
free_bch -> bch_free
encode_bch -> bch_encode
decode_bch -> bch_decode
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519074549.23673-2-miquel.raynal@bootlin.com
There are controllers not able to just read data cycles on the
bus. There are controllers not able to do a change column.
If we want to support both, we need to check which operation is
supported first. This is the exact same mechanism that is in use for
parameter page reads (ONFI/JEDEC) as the same problem occurs.
Speed testing does not show any throughput penalty so we do not
optimize more than that. However it is likely that, in the future, a
more robust and exhaustive test will run at boot time to avoid
re-checking what is supported and what is not at every call.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519130834.2918-1-miquel.raynal@bootlin.com
Mimic what's done in nand_soft_waitrdy() and add one to the jiffies
timeout so we don't end up waiting less than actually required.
Reported-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Fixes: b0e137ad24 ("mtd: rawnand: Provide helper for polling GPIO R/B pin")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200518155237.297549-1-boris.brezillon@collabora.com
Now that exec_op() is implemented we can get rid of the legacy interface
implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200513172248.141402-4-boris.brezillon@collabora.com
Implement exec_op() so we can later get rid of the legacy interface
implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200513172248.141402-3-boris.brezillon@collabora.com
Let's not rely on the dummy_controller embedded in nand_chip.legacy
and explicitly inherit from nand_controller instead.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200513172248.141402-1-boris.brezillon@collabora.com
The current code checks that the whole OOB area is erased.
This is a problem when JFFS2 cleanmarkers are added to the OOB, since it will
fail due to the usable OOB bytes not being 0xff.
Correct this by only checking that data and ECC bytes aren't 0xff.
Fixes: 02b88eea9f ("mtd: brcmnand: Add check for erased page bitflips")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200512082451.771212-1-noltari@gmail.com
Some controller using the instruction parse infrastructure might need
to know which CS a specific sub-operation is targeting. Let's propagate
this information.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200505101353.1776394-2-boris.brezillon@collabora.com
This patch renames functions and local variables.
This cleanup is done to get all functions starting by stm32_fmc2_nfc
in the FMC2 raw NAND driver when all functions will start by
stm32_fmc2_ebi in the FMC2 EBI driver.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1589284068-4079-2-git-send-email-christophe.kerello@st.com
This change fixes crash observed on PM resume. This bug
was introduced in the change made for flash-edu support.
Fixes: a5d53ad26a ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This is done by default in the raw NAND core (nand_base.c) but was
missing in the SPI-NAND core. Without these two lines the ecc_strength
and ecc_step_size values are not exported to the user through sysfs.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch removes the constant FMC2_TIMEOUT_US.
FMC2_TIMEOUT_MS will be used each time that we need to wait (except
when the timeout value is set by the framework).
It was seen, during stress tests with the sequencer in an overloaded
system, that we could be close to 1 second, even if we never met this
value. To be safe, FMC2_TIMEOUT_MS is set to 5 seconds.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1588756279-17289-4-git-send-email-christophe.kerello@st.com
Implement exec_op() so we can later get rid of the legacy
implementation.
It's worth noting that the new implementation assert/deassert the CE
pin on each operation, which might not be necessary. We also dropped
the extra reset done at chip selection time on DOC2001plus. If it's
needed we really should do something smarter, because having a reset
everytime we access the chip is not that great perf-wise.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501143917.1388957-5-boris.brezillon@collabora.com
Single byte accesses normally go through read_byte() but we are about
to use this function in the exec_op() implementation and thus needs to
prepare for single byte reads.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501143917.1388957-2-boris.brezillon@collabora.com
We have a dummy block_bad() implementation returning 0. Let's set the
NAND_NO_BBM_QUIRK flag and let the core take care of that.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200511064917.6255-3-boris.brezillon@collabora.com
We have a dummy block_bad() implementation returning 0. Let's set the
NAND_NO_BBM_QUIRK flag and let the core take care of that.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200511064917.6255-2-boris.brezillon@collabora.com
Some controllers with embedded ECC engines override the BBM marker with
data or ECC bytes, thus making bad block detection through bad block
marker impossible. Let's flag those chips so the core knows it shouldn't
check the BBM and consider all blocks good.
This should allow us to get rid of two implementers of the
legacy.block_bad() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200511064917.6255-1-boris.brezillon@collabora.com
Some controller drivers do not support executing regular
nand_read/write_page_raw() helpers. For that, we created
nand_monolithic_read/write_page_raw() alternatives. Let's now allow
the driver to overload the ECC ->read/write_page_raw() hooks when
these hooks are supported.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-14-miquel.raynal@bootlin.com
Some controller drivers do not support executing regular
nand_read/write_page_raw() helpers. For that, we created
nand_monolithic_read/write_page_raw() alternatives. Let's now allow
the driver to overload the ECC ->read/write_page_raw() hooks.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-13-miquel.raynal@bootlin.com
The current nand_read/write_page_raw() helpers are already widely used
but do not fit the purpose of "constrained" controllers which cannot,
for instance, separate command/address cycles with data cycles.
Workaround this issue by proposing alternative helpers that can be
used by these controller drivers instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-12-miquel.raynal@bootlin.com
We already know that there are controllers not able to read the three
copies of the parameter page in one go. The workaround was to first
request the controller to assert command and address cycles on the
NAND bus to trigger a parameter page read, and then do a read
operation for each page.
But there are also controllers which are not able to split the
parameter page read between the command/address cycles and the actual
data operation.
Let's use a regular PARAMETER PAGE READ operation for the first
iteration and use eithe a CHANGE READ COLUMN or a simple DATA READ
operation for the following copies, depending on what the controller
supports. The default for non-exec-op compliant drivers remains
unchanged: use a SIMPLE READ.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-11-miquel.raynal@bootlin.com
We already know that there are controllers not able to read the three
copies of the parameter page in one go. The workaround was to first
request the controller to assert command and address cycles on the
NAND bus to trigger a parameter page read, and then do a simple read
operation for each page.
But there are also controllers which are not able to split the
parameter page read between the command/address cycles and the actual
data operation.
Let's use a regular PARAMETER PAGE READ operation for the first
iteration and use either a CHANGE READ COLUMN or a simple DATA READ
operation for the following copies, depending on what the controller
supports. The default behavior for non-exec-op compliant drivers
remains the same: DATA READ.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-10-miquel.raynal@bootlin.com
This can be used to discriminate between two path in the parameter
page detection: use data_in cycles (like before) if supported, use the
CHANGE READ COLUMN command otherwise.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-9-miquel.raynal@bootlin.com
Let's use a helper to clearly check if an operation is supported or not.
Return -ENOTSUPP when ->exec_op() is not implemented as we cannot know.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-8-miquel.raynal@bootlin.com
The logic in nand_do_read_ops() is to use a bufpoi variable, either
set to the original buffer, or set to a bounce buffer which in the end
happens to be chip->data_buf depending on the value of the
use_bounce_buf boolean. This is not a reason to call chip->data_buf
directly when we know that we are using the bounce buffer. Let's use
bufpoi instead to be consistent.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-7-miquel.raynal@bootlin.com
Both in nand_do_read_ops() and nand_do_write_ops() there is a boolean
called use_bufpoi which is set to true in case of unaligned request or
when there is a need for a DMA-able buffer. It basically means "use a
bounce buffer".
Depending on the value of use_bufpoi, the bufpoi variable is always
used and will either point to the original buffer or to the nand_chip
structure "internal data buffer" (this buffer is allocated with
kmalloc() on purpose so that it will be DMA-compliant).
In all cases bufpoi is used so the boolean name is misleading. Rename
use_bufpoi to be use_bouce_buf to be more accurate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-6-miquel.raynal@bootlin.com
NAND controller drivers can set the NAND_USE_BOUNCE_BUFFER flag to a
chip 'option' field. With this flag, the core is responsible of
providing DMA-able buffers.
The current behavior is to not force the use of a bounce buffer when
the core thinks this is not needed. So in the end the name is a bit
misleading, because in theory we will always have a DMA buffer but in
practice it will not always be a bounce buffer.
Rename this flag NAND_USES_DMA to be more accurate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-4-miquel.raynal@bootlin.com
Now that exec_op() is implemented we no longer need to implement the
legacy hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501090650.1138200-5-boris.brezillon@collabora.com
Now that we have our own controller struct we can keep the MMIO pointer
in there and use instead of using the chip->legacy.IO_ADDR_{R,W} fields.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501090650.1138200-3-boris.brezillon@collabora.com
The CS553x companion chip embeds 4 NAND controllers. Declare them as
NAND controllers instead of NAND chips. That's done in preparation
of the transition to exec_op().
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501090650.1138200-2-boris.brezillon@collabora.com
Before reworking a little bit the JEDEC detection code, let's
clean the coding style of an if statement to improve readability.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-10-miquel.raynal@bootlin.com
During detection the logic on the NAND bus is:
/* Regular ONFI detection */
1/ read the three NAND parameter pages
/* Extended parameter page detection */
2/ send "read the NAND parameter page" commands without reading
actual data
3/ move the column pointer to the extended page and read it
If fact, as long as there is nothing happening on the NAND bus between
1/ and 3/, the operation 2/ is redundant so remove it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-8-miquel.raynal@bootlin.com
Before reworking a little bit the ONFI detection code, let's
clean the coding style of the if statements to improve readability.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-5-miquel.raynal@bootlin.com
During ONFI detection, the CRC derived from the parameter page and the
CRC supposed to be at the end of the parameter page are compared. If
they do not match, the second then the third copies of the page are
tried.
The current implementation compares the newly derived CRC with the CRC
contained in the first page only. So if this particular CRC area has
been corrupted, then the detection will fail for a wrong reason.
Fix this issue by checking the derived CRC against the right one.
Fixes: 39138c1f4a ("mtd: rawnand: use bit-wise majority to recover the ONFI param page")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-4-miquel.raynal@bootlin.com
tR and tCCS are currently wrongly expressed in femtoseconds, while we
expect these values to be expressed in picoseconds. Set right
hardcoded values.
Fixes: 6a943386ee mtd: rawnand: add default values for dynamic timings
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-3-miquel.raynal@bootlin.com
Convert the timings union into a structure containing the mode and the
actual values. The values are still a union in prevision of the
addition of the NVDDR modes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-2-miquel.raynal@bootlin.com
There is no correction involved at this point, it is just a matter of
reading registers and checking whether bitflips have occurred or
not. Rename the function to clarify it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-7-miquel.raynal@bootlin.com
Do not call nand_release() while the MTD device has not been
registered, use nand_cleanup() instead.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-4-miquel.raynal@bootlin.com
Switch from the old platform_get_resource()/devm_ioremap_resource()
couple to the newer devm_platform_ioremap_resource() helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-3-miquel.raynal@bootlin.com
In a previous fix, I changed the condition on which the timeout of an
IRQ is reached from:
if (!ret)
into:
if (ret && !pending)
While having a non-zero return code is usual in the Linux kernel, here
ret comes from a wait_for_completion_timeout() which returns 0 when
the waiting period is too long.
Hence, the revised condition should be:
if (!ret && !pending)
The faulty patch did not produce any error because of the !pending
condition so this change is finally purely cosmetic and does not
change the actual driver behavior.
Fixes: cafb56dd74 ("mtd: rawnand: marvell: prevent timeouts on a loaded machine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-2-miquel.raynal@bootlin.com
When the ECC strength is too weak compared to the NAND chip
requirements, display the values so that it is clear for people how
much they are far from the requirements (and might get in troubles in
the future).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200421163906.7515-1-miquel.raynal@bootlin.com
We are about to re-use those for the exec_op() implementation which
will not rely on au1550_hwcontrol(). Let's patch those helpers to
simply use the iomem address stored in the context.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200419193037.1544035-2-boris.brezillon@collabora.com
The Denali IP have several registers to specify how many clock cycles
should be waited between falling/rising signals. You can improve the
NAND access performance by programming these registers with optimized
values.
Because struct nand_sdr_timings represents the device requirement
in pico seconds, denali_setup_data_interface() computes the register
values by dividing the device timings with the clock period.
Marek Vasut reported this driver in the latest kernel does not work
on his SOCFPGA board. (The on-board NAND chip is mode 5)
The suspicious parameter is acc_clks, so this commit relaxes it.
The Denali NAND Flash Memory Controller User's Guide describes this
register as follows:
acc_clks
signifies the number of bus interface clk_x clock cycles,
controller should wait from read enable going low to sending
out a strobe of clk_x for capturing of incoming data.
Currently, acc_clks is calculated only based on tREA, the delay on the
chip side. This does not include additional delays that come from the
data path on the PCB and in the SoC, load capacity of the pins, etc.
This relatively becomes a big factor on faster timing modes like mode 5.
Before supporting the ->setup_data_interface() hook (e.g. Linux 4.12),
the Denali driver hacks acc_clks in a couple of ways [1] [2] to support
the timing mode 5.
We would not go back to the hard-coded acc_clks, but we need to include
this factor into the delay somehow. Let's say the amount of the additional
delay is 10000 pico sec.
In the new calculation, acc_clks is determined by timings->tREA_max +
data_setup_on_host.
Also, prolong the RE# low period to make sure the data hold is met.
Finally, re-center the data latch timing for extra safety.
[1] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L276
[2] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L282
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200317071821.9916-1-yamada.masahiro@socionext.com
->exec_op() is passed a check_only argument that encodes when the
controller should just check whether the operation is supported or not
without executing it. Some controllers simply ignore this arguments,
others don't but keep modifying some of the registers before returning.
Let's fix all those drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200418194217.1016060-1-boris.brezillon@collabora.com
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200417101129.35556-1-yuehaibing@huawei.com
Fix sparse warning:
drivers/mtd/nand/raw/cadence-nand-controller.c:2595:5:
warning: symbol 'cadence_nand_attach_chip' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200410115228.30440-1-yuehaibing@huawei.com
Fix sparse warning:
drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c:105:32:
warning: symbol 'qi_lb60_ooblayout_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200410115121.11852-1-yuehaibing@huawei.com
No need to use expensive atomic change_bit() on dat[] and err_idx[]:
1. fsmc_bch8_correct_data() is called while mutex chip->lock is held
2. err_idx[] is a local variable.
To avoid big endian concern due to type cast to unsigned long, directly
change the bit in the specified byte instead of using non-atomic
__change_bit().
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1576886755-9788-1-git-send-email-fenghua.yu@intel.com
Use Joe Perches cvt_fallthrough.pl script to convert
/* fallthrough */
comments (and its derivatives) into a
fallthrough;
statement. This automatically drops useless ones.
Do it MTD-wide.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/linux-mtd/20200325212115.14170-1-miquel.raynal@bootlin.com
* Add support for manufacturer specific suspend/resume operation
* Add support for manufacturer specific lock/unlock operation
* Replace zero-length array with flexible-array member
* Fix a typo ("manufecturer")
* Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
* Brcmnand:
Add support for flash-edu for dma transfers (+ bindings)
* Cadence:
Reinit completion before executing a new command
Change bad block marker size
Fix the calculation of the avaialble OOB size
Get meta data size from registers
* Qualcom:
Use dma_request_chan() instead dma_request_slave_channel()
Release resources on failure within qcom_nandc_alloc()
* Allwinner:
Use dma_request_chan() instead dma_request_slave_channel()
* Marvell:
Use dma_request_chan() instead dma_request_slave_channel()
Release DMA channel on error
* Freescale:
Use dma_request_chan() instead dma_request_slave_channel()
* Macronix:
Add support for Macronix NAND randomizer (+ bindings)
* Ams-delta:
Rename structures and functions to gpio_nand*
Make the driver custom I/O ready
Drop useless local variable
Support custom driver initialisation
Add module device tables
Handle more GPIO pins as optional
Make read pulses optional
Don't hardcode read/write pulse widths
Push inversion handling to gpiolib
Enable OF partition info support
Drop board specific partition info
Use struct gpio_nand_platdata
Write protect device during probe
* Ingenic:
Use devm_platform_ioremap_resource()
Add dependency on MIPS || COMPILE_TEST
* Denali:
Deassert write protect pin
* ST:
Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
* Toshiba:
Support reading the number of bitflips for BENAND (Built-in ECC NAND)
* Macronix:
Add support for deep power down mode
Add support for block protection
SPI-NAND core changes:
* Do not erase the block before writing a bad block marker
* Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
* Stop using spinand->oobbuf for buffering bad block markers
* Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
* Toshiba:
Support for new Kioxia Serial NAND
Rename function name to change suffix and prefix (8Gbit)
Add comment about Kioxia ID
* Micron:
Add new Micron SPI NAND devices with multiple dies
Add M70A series Micron SPI NAND devices
identify SPI NAND device with Continuous Read mode
Add new Micron SPI NAND devices
Describe the SPI NAND device MT29F2G01ABAGD
Generalize the OOB layout structure and function names
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl5+XuIACgkQJWrqGEe9
VoRCAggAh0bpso9l8enk+ae1LrEGGLCV0sWMBy/pwM4zaBovqJqSdXRybg1IQE1N
5AvZrcQUBzdr9RzusB0J/xVC31gStjNQJROekArHJI6rzjoHRM/779fx0JV1JJHI
sWgX7UY7AVMH1l4BMB0mMezFeqJnZU5JRHQ+we3X4funNJ2JcBwvp1u4XJ2BDLRn
oCDLYgMC9S4lWEP7/ARgv27w7GfaegCUqNOHBVH75d2c+l476z5TKUap8s/LjI8u
8eRGerwLTj8/PLj1OqSEKXeJem2gZvZNpDCylgzrGZbU9r0M5I/EdXxJ90Pj6bR0
+G/0JHb4C1DXeDXzw79KisggHDkUUA==
=Zmzp
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.7' into mtd/next
Raw NAND core changes:
* Add support for manufacturer specific suspend/resume operation
* Add support for manufacturer specific lock/unlock operation
* Replace zero-length array with flexible-array member
* Fix a typo ("manufecturer")
* Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
* Brcmnand:
Add support for flash-edu for dma transfers (+ bindings)
* Cadence:
Reinit completion before executing a new command
Change bad block marker size
Fix the calculation of the avaialble OOB size
Get meta data size from registers
* Qualcom:
Use dma_request_chan() instead dma_request_slave_channel()
Release resources on failure within qcom_nandc_alloc()
* Allwinner:
Use dma_request_chan() instead dma_request_slave_channel()
* Marvell:
Use dma_request_chan() instead dma_request_slave_channel()
Release DMA channel on error
* Freescale:
Use dma_request_chan() instead dma_request_slave_channel()
* Macronix:
Add support for Macronix NAND randomizer (+ bindings)
* Ams-delta:
Rename structures and functions to gpio_nand*
Make the driver custom I/O ready
Drop useless local variable
Support custom driver initialisation
Add module device tables
Handle more GPIO pins as optional
Make read pulses optional
Don't hardcode read/write pulse widths
Push inversion handling to gpiolib
Enable OF partition info support
Drop board specific partition info
Use struct gpio_nand_platdata
Write protect device during probe
* Ingenic:
Use devm_platform_ioremap_resource()
Add dependency on MIPS || COMPILE_TEST
* Denali:
Deassert write protect pin
* ST:
Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
* Toshiba:
Support reading the number of bitflips for BENAND (Built-in ECC NAND)
* Macronix:
Add support for deep power down mode
Add support for block protection
SPI-NAND core changes:
* Do not erase the block before writing a bad block marker
* Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
* Stop using spinand->oobbuf for buffering bad block markers
* Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
* Toshiba:
Support for new Kioxia Serial NAND
Rename function name to change suffix and prefix (8Gbit)
Add comment about Kioxia ID
* Micron:
Add new Micron SPI NAND devices with multiple dies
Add M70A series Micron SPI NAND devices
identify SPI NAND device with Continuous Read mode
Add new Micron SPI NAND devices
Describe the SPI NAND device MT29F2G01ABAGD
Generalize the OOB layout structure and function names
The suffix was changed from "G" to "J" to classify between 1st generation
and 2nd generation serial NAND devices (which now belong to the Kioxia
brand).
As reference that's
1st generation device of 1Gbit product is "TC58CVG0S3HRAIG"
2nd generation device of 1Gbit product is "TC58CVG0S3HRAIJ".
The 8Gbit type "TH58CxG3S0HRAIJ" is new to Kioxia's serial NAND lineup and
the prefix was changed from "TC58" to "TH58".
Thus the functions were renamed from tc58cxgxsx_*() to tx58cxgxsxraix_*().
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/0dedd9869569a17625822dba87878254d253ba0e.1584949601.git.ytc-mb-yfuruyama7@kioxia.com
Macronix AD series support deep power down mode for a minimum
power consumption state.
Overload nand_suspend() & nand_resume() in Macronix specific code to
support deep power down mode.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add device table for new Micron SPI NAND devices, which have multiple
dies.
Also, enable support to select the dies.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200311175735.2007-7-sshivamurthy@micron.com
Add SPINAND_HAS_CR_FEAT_BIT flag to identify the SPI NAND device with
the Continuous Read mode.
Some of the Micron SPI NAND devices have the "Continuous Read" feature
enabled by default, which does not fit the subsystem needs.
In this mode, the READ CACHE command doesn't require the starting column
address. The device always output the data starting from the first
column of the cache register, and once the end of the cache register
reached, the data output continues through the next page. With the
continuous read mode, it is possible to read out the entire block using
a single READ command, and once the end of the block reached, the output
pins become High-Z state. However, during this mode the read command
doesn't output the OOB area.
Hence, we disable the feature at probe time.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200311175735.2007-5-sshivamurthy@micron.com
Add the SPI NAND device MT29F2G01ABAGD series number, size and voltage
details as a comment.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200311175735.2007-3-sshivamurthy@micron.com
In order to add new Micron SPI NAND devices, we generalized the OOB
layout structure and function names.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200311175735.2007-2-sshivamurthy@micron.com
Legacy mips soc platforms that have controller v5.0 and 6.0 use
flash-edu block for dma transfers. This change adds support for
nand dma transfers using the EDU block.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200122213313.35820-4-kdasu.kdev@gmail.com
Increase bad block marker size from one byte to two bytes.
Bad block marker is handled by skip bytes feature of HPNFC.
Controller expects this value to be an even number.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-3-git-send-email-piotrs@cadence.com
The value of cdns_chip->sector_count is not known at the moment
of the derivation of ecc_size, leading to a zero value. Fix
this by assigning ecc_size later in the code.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-2-git-send-email-piotrs@cadence.com
Add checking size of BCH meta data size in capabilities registers
instead of using fixed value. BCH meta data is used to keep data
from NAND flash OOB area.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-1-git-send-email-piotrs@cadence.com
This driver has no arch-specific instructions but is only ever useful
on MIPS; so disable this driver if we're not compiling for MIPS, unless
the driver is compile-tested.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200302184509.10666-1-paul@crapouillou.net
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly and inform user of error in case the
DMA request failed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-8-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-7-peter.ujfalusi@ti.com
In case when DMA channel request or alloc_bam_transaction() fails,
dma_unmap_single() and any channels already requested should be released.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-6-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-5-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-4-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-2-peter.ujfalusi@ti.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200226222722.GA18020@embeddedor
Currently when marking a block, we use spinand_erase_op() to erase
the block before writing the marker to the OOB area. Doing so without
waiting for the operation to finish can lead to the marking failing
silently and no bad block marker being written to the flash.
In fact we don't need to do an erase at all before writing the BBM.
The ECC is disabled for raw accesses to the OOB data and we don't
need to work around any issues with chips reporting ECC errors as it
is known to be the case for raw NAND.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-4-frieder.schrempf@kontron.de
When writing the bad block marker to the OOB area the access mode
should be set to MTD_OPS_RAW as it is done for reading the marker.
Currently this only works because req.mode is initialized to
MTD_OPS_PLACE_OOB (0) and spinand_write_to_cache_op() checks for
req.mode != MTD_OPS_AUTO_OOB.
Fix this by explicitly setting req.mode to MTD_OPS_RAW.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-3-frieder.schrempf@kontron.de
For reading and writing the bad block markers, spinand->oobbuf is
currently used as a buffer for the marker bytes. During the
underlying read and write operations to actually get/set the content
of the OOB area, the content of spinand->oobbuf is reused and changed
by accessing it through spinand->oobbuf and/or spinand->databuf.
This is a flaw in the original design of the SPI NAND core and at the
latest from 13c15e07ee ("mtd: spinand: Handle the case where
PROGRAM LOAD does not reset the cache") on, it results in not having
the bad block marker written at all, as the spinand->oobbuf is
cleared to 0xff after setting the marker bytes to zero.
To fix it, we now just store the two bytes for the marker on the
stack and let the read/write operations copy it from/to the page
buffer later.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-2-frieder.schrempf@kontron.de
Macronix NANDs support randomizer operation for user data scrambled,
which can be enabled with a SET_FEATURE.
User data written to the NAND device without randomizer is still readable
after randomizer function enabled.
The penalty of randomizer are subpage accesses prohibited and more time
period is needed in program operation and entering deep power-down mode.
i.e., tPROG 300us to 340us(randomizer enabled)
For more high-reliability concern, if subpage write not available with
hardware ECC and then to enable randomizer is recommended by default.
Driver checks byte 167 of Vendor Blocks in ONFI parameter page table
to see if this high-reliability function is supported. By adding a new
specific DT property in children nodes to enable randomizer function.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581922600-25461-2-git-send-email-masonccyang@mxic.com.tw
In order to be merged with "gpio-nand", the driver must support custom
(non-GPIO) I/O accessors.
Allow platforms to omit data GPIO port as well as NWE pin info from
device setup. For the driver to still work on such platform, custom
I/O accessors as well as a custom probe function which initialises the
driver private structure with those accessors must be added to the
driver.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-14-jmkrzyszt@gmail.com
For consistency with adjacent code patterns used in the driver probe
function, store data GPIO array pointer directly in a respective field
of the driver private structure instead of storing it intermediately
in a local variable for error checking.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-13-jmkrzyszt@gmail.com
In preparation for extending the driver with custom I/O support, try to
obtain device specific initialisation routine from a matching device
table entry and run it as an additional step of device probe.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-12-jmkrzyszt@gmail.com
In preparation for merging the driver with "gpio-nand", introduce
module device tables where new device models can be accommodated as
soon as respective support is added.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-11-jmkrzyszt@gmail.com
In order to make the driver more useful on platforms other than Amstrad
Delta, allow GPIO descriptor pointers of possibly non-critical NWP and
NCE pins to be initialised as NULL.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-10-jmkrzyszt@gmail.com
Allow platforms to omit NRE pin from device configuration by requesting
that pin as optional. In that case, also don't apply read pulse width
from chip SDR timings. There should be no need for further code
adjustments as gpiolib can handle NULL GPIO descriptor pointers.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-9-jmkrzyszt@gmail.com
Instead of forcing Amstrad Delta specific read/write pulse widths, use
variables initialised from respective fields of chip SDR timings.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-8-jmkrzyszt@gmail.com
Let platforms take care of declaring correct GPIO pin polarity so we
can just ask a GPIO line to be asserted or deasserted and gpiolib deals
with the rest depending on how the platform is configured.
Inspired by similar changes to regulator drivers by Linus Walleij
<linus.walleij@linaro.org>, thanks!
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-7-jmkrzyszt@gmail.com
Now as we support fetching partition info from device platform data and
the Amstrad Delta board file provides that info, drop it from the
driver code.
v2: rebase on top of gpio_nand_platdata extension
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-5-jmkrzyszt@gmail.com
In order to be able to move the hardcoded Amstrad Delta partition info
from the driver code to the board file, reuse gpio_nand_platdata
structure owned by "gpio-nand" driver and try to obtain information
on device partitions from device platform data.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-3-jmkrzyszt@gmail.com
Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
Tested on GD5F1GQ4UAYIG and W25N01GVZEIG.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200208074439.146296-1-gch981213@gmail.com
Add a comment above NAND_MFR_TOSHIBA and SPINAND_MFR_TOSHIBA definitions
that Toshiba and Kioxia ID are the same.
Since its independence from Toshiba Group, Toshiba memory Co has become
Kioxia Co.
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581051561-7302-1-git-send-email-ytc-mb-yfuruyama7@kioxia.com
If the write protect signal from this IP is connected to the NAND
device, this IP can handle the WP# pin via the WRITE_PROTECT
register.
The Denali NAND Flash Memory Controller User's Guide describes
this register like follows:
When the controller is in reset, the WP# pin is always asserted
to the device. Once the reset is removed, the WP# is de-asserted.
The software will then have to come and program this bit to
assert/de-assert the same.
1 - Write protect de-assert
0 - Write protect assert
The default value is 1, so the write protect is de-asserted after
the reset is removed. The driver can write to the device unless
someone has explicitly cleared register before booting the kernel.
The boot ROM of some UniPhier SoCs (LD4, Pro4, sLD8, Pro5) is the
case; the boot ROM clears the WRITE_PROTECT register when the system
is booting from the NAND device, so the NAND device becomes read-only.
Set it to 1 in the driver in order to allow the write access to the
device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200127123934.11847-1-yamada.masahiro@socionext.com
The used way to compute jiffies timeout brokes when
jiffie difference is 1.
Assume that nand_soft_waitrdy is called with timeout_ms==1.
Jiffies are 1000 for example (assume something more like 1000.99
- just before incrementing to 1001).
We compute timeout_ms = 1000+msecs_to_jiffies(1) = 1001.
nand_read_data_op is called for the first time and returns 0.
During the call jiffies changes to 1001 thus "while loop" ends
here (wrongly). Notice that routine was called with expected timeout
1ms but actual timeout used was something between 0...1ms.
Fixes STM32MP1 FMC2 NAND controller which sometimes failed
exactly in this way.
Signed-off-by: Martin Devera <devik@eaxlabs.cz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200116135431.17480-1-devik@eaxlabs.cz
* block2mtd: page index should use pgoff_t
* maps: physmap: minimal Runtime PM support
* maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
* concat: Fix a comment referring to an unknown symbol
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Cadence: add unspecified HAS_IOMEM dependency
* Various cleanup.
Onenand
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl4zMfgACgkQJWrqGEe9
VoS0xwf+KdaihRno4SkDovcHoF7K54N6CqBhwuV9uabfy4phEr38cyvaivYu0rG7
k/n3CUNRDghTh7DAUT7pBsjUeZn9XxvKyQaZz34TBgoQYwGz57ssp8lMRmJkYoA6
t9z95N9bRJ+IzZJlYELCbhNq+aOGyWYgWL+aaO0CE8OyOeWzdZumdd4k7cF7rSAu
9gWV/6iX/qP081NexfjPEVmMtNQ+0p4T7zQ01nQA7rIZiVoIgMKwBu41aRYycEEs
LeuV5gNEDn2vGBl+u85w5oF6o1TIzDeTmh0G7Jm3NQGGco2kOOZ1O39a0hrDONrA
hEoEIG/rAMKOtaLr6rCGnV/5/i/Tlw==
=WC+m
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core
- block2mtd: page index should use pgoff_t
- maps: physmap: minimal Runtime PM support
- maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
- concat: Fix a comment referring to an unknown symbol
Raw NAND:
- Macronix: Use match_string() helper
- Atmel: switch to using devm_fwnode_gpiod_get()
- Denali: rework the SKIP_BYTES feature and add reset controlling
- Brcmnand: set appropriate DMA mask
- Cadence: add unspecified HAS_IOMEM dependency
- Various cleanup.
Onenand:
- Rename Samsung and Omap2 drivers to avoid possible build warnings
- Enable compile testing
- Various build issues
- Kconfig cleanup
SPI-NAND:
- Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes"
* tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (41 commits)
mtd: concat: Fix a comment referring to an unknown symbol
mtd: rawnand: add unspecified HAS_IOMEM dependency
mtd: block2mtd: page index should use pgoff_t
mtd: maps: physmap: Add minimal Runtime PM support
mtd: maps: pcmciamtd: fix possible sleep-in-atomic-context bugs in pcmciamtd_set_vpp()
mtd: onenand: Rename omap2 driver to avoid a build warning
mtd: onenand: Use a better name for samsung driver
mtd: rawnand: atmel: switch to using devm_fwnode_gpiod_get()
mtd: spinand: add support for Toshiba TC58CVG2S0HRAIJ
mtd: rawnand: macronix: Use match_string() helper to simplify the code
mtd: sharpslpart: Fix unsigned comparison to zero
mtd: onenand: Enable compile testing of OMAP and Samsung drivers
mtd: onenand: samsung: Fix printing format for size_t on 64-bit
mtd: onenand: samsung: Fix pointer cast -Wpointer-to-int-cast warnings on 64 bit
mtd: rawnand: denali: remove hard-coded DENALI_DEFAULT_OOB_SKIP_BYTES
mtd: rawnand: denali_dt: add reset controlling
dt-bindings: mtd: denali_dt: document reset property
mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
mtd: rawnand: denali_dt: error out if platform has no associated data
mtd: rawnand: brcmnand: Set appropriate DMA mask
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl4nSy0ACgkQJWrqGEe9
VoSr1gf+KKMtE8GabWYbKsgKRx1cmC/0pvRmp7wqjul4gd/s+llKzEDG/qMYUOua
PgynNJeP7LPIZJWqo8TjXZcNxs1E0JSoAjYK58Hm9MOIwiwmdSE7GOVxv8/1drN/
7mjJvnGznol/2GD3U4NRvW/SZHkj0/Xt9Ys70qdpcWDQWJSIUIhrNuKOMgjTP+kp
XfZ4vWL6T9LHJiIojLTkrfjXH774dWflSj8bySz+9d9kwkbvKEGU6zb6sKfGO4nm
yYqQhpUrbN8c4t+hSuJlf140haVhwCIQeujUNlTn2oDXnJIO/98k0jDSn6dpUSdx
H6NvWMa8e8Bz7HAbB7/VOawtjt/k+w==
=UPI6
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.6' into mtd/next
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
Currently CONFIG_MTD_NAND_CADENCE implicitly depends on
CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get
the following build error:
ld: drivers/mtd/nand/raw/cadence-nand-controller.o: in function `cadence_nand_dt_probe.cold.31':
drivers/mtd/nand/raw/cadence-nand-controller.c:2969: undefined reference to `devm_platform_ioremap_resource'
ld: drivers/mtd/nand/raw/cadence-nand-controller.c:2977: undefined reference to `devm_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As previously reported by Sudip Mukherjee for the Samsung driver, the
omap2 onenand driver is called omap2.c in our directory and omap2.c in
the tty/serial/ directory. If both drivers are compiled as modules, it
would produce the following warning:
warning: same module names found:
drivers/tty/serial/omap2.ko
drivers/mtd/nand/onenand/omap2.ko
Rename the onenand omap2 driver so that it fits the folder's
convention: onenand_omap2.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 55ed51fff2 ("{tty: serial, nand: onenand}: samsung: rename to
fix build warning") has changed the samsung.c driver to be
samsung_mtd.c in order to avoid a conflict in module names with the
tty driver.
Since the *_mtd suffix is very undescriptive, rename it to
onenand_samsung.c, following the folder's convention. Same will be
applied to the omap2 onenand driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
devm_fwnode_get_index_gpiod_from_child() is going away as the name is
too unwieldy, let's switch to using the new devm_fwnode_gpiod_get().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Toshiba recently launched new revisions of their serial SLC NAND series.
TC58CVG2S0HRAIJ is a refresh of previous series with minor improvements.
Basic parameters are same so lets add support for this new revision.
Datasheet: https://business.kioxia.com/info/docget.jsp?did=58601&prodName=TC58CVG2S0HRAIJ
Tested under kernel 5.4.7.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
OMAP and Samsung OneNAND drivers can be compile tested. The OMAP
drivers still depends on mach header so limit the compile testing to
ARMv7.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Print size_t as %zu to fix -Wformat warnings when compiling on 64-bit
platform (e.g. with COMPILE_TEST):
drivers/mtd/nand/onenand/samsung_mtd.c: In function ‘s5pc110_read_bufferram’:
drivers/mtd/nand/onenand/samsung_mtd.c:661:16: warning:
format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
dev_err(dev, "Couldn't map a %d byte buffer for DMA\n", count);
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
iomem pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings when compiling on 64-bit platform (e.g.
with COMPILE_TEST):
drivers/mtd/nand/onenand/samsung_mtd.c: In function ‘s3c_onenand_readw’:
drivers/mtd/nand/onenand/samsung_mtd.c:251:6: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
if ((unsigned int) addr < ONENAND_DATARAM && onenand->bootram_command) {
^
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As commit 0d55c668b2 (mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES
register to 8 if unset") says, there were three solutions discussed:
[1] Add a DT property to specify the skipped bytes in OOB
[2] Associate the preferred value with compatible
[3] Hard-code the default value in the driver
At that time, [3] was chosen because I did not have enough information
about the other platforms than UniPhier.
That commit also says "The preferred value may vary by platform. If so,
please trade up to a different solution." My intention was to replace
[3] with [2], not keep both [2] and [3].
Now that we have switched to [2] for SOCFPGA's SPARE_AREA_SKIP_BYTES=2,
[3] should be removed. This should be OK because denali_pci.c just
gets back to the original behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
According to the Denali NAND Flash Memory Controller User's Guide,
this IP has two reset signals.
rst_n: reset most of FFs in the controller core
reg_rst_n: reset all FFs in the register interface, and in the
initialization sequencer
This commit supports controlling those reset signals.
It is possible to control them separately from the IP point of view
although they might be often tied up together in actual SoC integration.
The IP spec says, asserting only the reg_rst_n without asserting rst_n
will cause unpredictable behavior in the controller. So, the driver
deasserts ->rst_reg and ->rst in this order.
Another thing that should be kept in mind is the automated initialization
sequence (a.k.a. 'bootstrap' process) is kicked off when reg_rst_n is
deasserted.
When the reset is deasserted, the controller issues a RESET command
to the chip select 0, and attempts to read out the chip ID, and further
more, ONFI parameters if it is an ONFI-compliant device. Then, the
controller sets up the relevant registers based on the detected
device parameters.
This process might be useful for tiny boot firmware, but is redundant
for Linux Kernel because nand_scan_ident() probes devices and sets up
parameters accordingly. Rather, this hardware feature is annoying
because it ends up with misdetection due to bugs.
So, commit 0615e7ad5d ("mtd: nand: denali: remove Toshiba and Hynix
specific fixup code") changed the driver to not rely on it.
However, there is no way to prevent it from running. The IP provides
the 'bootstrap_inhibit_init' port to suppress this sequence, but it is
usually out of software control, and dependent on SoC implementation.
As for the Socionext UniPhier platform, LD4 always enables it. For the
later SoCs, the bootstrap sequence runs depending on the boot mode.
I added usleep_range() to make the driver wait until the sequence
finishes. Otherwise, the driver would fail to detect the chip due
to the race between the driver and hardware-controlled sequence.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The SPARE_AREA_SKIP_BYTES register is reset when the controller reset
signal is toggled. Yet, this register must be configured to match the
content of the NAND OOB area. The current default value is always set
to 8 and is programmed into the hardware in case the hardware was not
programmed before (e.g. in a bootloader) with a different value. This
however does not work when the block is reset properly by Linux.
On Altera SoCFPGA CycloneV, ArriaV and Arria10, which are the SoCFPGA
platforms which support booting from NAND, the SPARE_AREA_SKIP_BYTES
value must be set to 2. On Socionext Uniphier, the value is 8. This
patch adds support for preconfiguring the default value and handles
the special SoCFPGA case by setting the default to 2 on all SoCFPGA
platforms, while retaining the original behavior and default value of
8 on all the other platforms.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
To: linux-mtd@lists.infradead.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
denali->ecc_caps is a mandatory parameter. If it were left unset,
nand_ecc_choose_conf() would end up with NULL pointer access.
So, every compatible must be associated with proper denali_dt_data.
If of_device_get_match_data() returns NULL, let it fail immediately.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NAND controllers >= 7.0 with FLASH_DMA support physical addresses up to
40-bit, set an appropriate DMA mask for that purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Clang warns:
../drivers/mtd/nand/onenand/onenand_base.c:1269:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
while (!ret) {
^
../drivers/mtd/nand/onenand/onenand_base.c:1266:2: note: previous
statement is here
if (column + thislen > writesize)
^
1 warning generated.
This warning occurs because there is a space before the tab of the while
loop. There are spaces at the beginning of a lot of the lines in this
block, remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
Fixes: a8de85d557 ("[MTD] OneNAND: Implement read-while-load")
Link: https://github.com/ClangBuiltLinux/linux/issues/794
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/nand/onenand/samsung_mtd.c: In function s3c_onenand_check_lock_status:
drivers/mtd/nand/onenand/samsung_mtd.c:731:6: warning: variable tmp set but not used [-Wunused-but-set-variable]
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The commit converting the driver to DMAengine was missing the flags for
the memcpy prepare call.
It went unnoticed since the omap-dma driver was ignoring them.
Fixes: 3ed6a4d1de (" mtd: onenand: omap2: Convert to use dmaengine for memcp")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use dma_addr_t type to pass memory address and control data in
DMA descriptor fields memory_pointer and ctrl_data_ptr
To fix warning: cast to pointer from integer of different size
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We are currently using nand_soft_waitrdy to poll the status of the NAND
flash. FMC2 enables the wait feature bit (this feature is mandatory for
the sequencer mode). By enabling this feature, we can't poll the status
of the NAND flash, the read status command is stucked in FMC2 pipeline
until R/B# signal is high, and locks the CPU bus.
To avoid to lock the CPU bus, we poll FMC2 ISR register. This register
reports the status of the R/B# signal.
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and
'CONFIG_SERIAL_SAMSUNG=m' gives a build warning:
warning: same module names found:
drivers/tty/serial/samsung.ko
drivers/mtd/nand/onenand/samsung.ko
Rename both drivers/tty/serial/samsung.c to
drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c
drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl3KwQYACgkQJWrqGEe9
VoTj1wf/Zvnk1u2vNVUaWDaHnUTAcMvjYNr1N1ppXquRXQTknZHxcgqavcwOA3yV
inHRdjQpvTPft3Pb0tddC2VBOMQTYWDGJs6JOLiPF5c4QdW/w4yHRrdnEIumbVP/
itXySbPj2QsXcRuIoEm165NTI8mdSzZFixZvCNS58r2mvMXvQbcUHsP9vjlUs9/S
XPqBlSBPKa6hC2ToIiXhgkGDQzVJ/OkCOSgG+37ATUrEqWUi9oN2KUPkbk4HSZe9
dntUIFSjeAqGjKGRGwAlt4axhnFWABfWa9xBwX9k5s4mt/FJ9QF24geemz/F1Ljp
7xd6MJu3JYoW8qBcXRRDgHuv5RNnHA==
=rpUJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.5' into mtd/next
Raw NAND core
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl3Kep8ACgkQS1VPR6WN
FOn9kgf/aKPgU6LR84YpwUKRZ4S+6K1H8SdDUt8v0FYSQ6oaTjF13fApg43WDja5
Zk0l5tlX7WIvlcRC6XKPhryZTXOKWojW1X8sguPYIZGzo7q82Eyda23jkw1QptWr
VO9L/tdK4yVUbdtp6VS/FUF31PC0DtDoCzsfBSUgrZP2srFF1BtOJNUgyuDceoxo
y3hEmINDnkaOvDDl/kbJjdEHG4PV8Vi4k0KE8deLpqlp8GDG1nkTeA1Sim7WjBPA
ZZOdg9fmGI8H8+umQEnn06H4O95T2+fX+kDMCYo4RbgWyWlGv5TidgRREmC/cSbl
YEPu6LCQoUZPVEvgolr/8Akf968ZiQ==
=i15M
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.5' into mtd/next
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
Remove unecessary checking if dmac is NULL.
If Cadence nand controller driver uses DMA engine then cdns_ctrl->dmac
cannot be NULL. It is verified during driver initialization.
If Cadence nand controller driver does not use DMA engine then
CPU IO read/write are executed instead of slave DMA transfer.
In that case cdns_ctrl->dmac is not used at all.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sparse complained about the following:
drivers/mtd/nand/raw/brcmnand/brcmnand.c:921:40: warning: Using plain integer as NULL pointer
fix this issue by assigning the pointer to NULL.
Fixes: c1ac2dc34b ("mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller and
NAND chips") supported the new binding for the separate controller/chip
representation, keeping the backward compatibility.
All the device trees in upstream migrated to the new binding.
Remove the support for the old binding.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to
chip->read_xxx() hooks") modified the prototype of the struct nand_chip
read_buf function pointer. In the au1550nd driver we have 2
implementations of read_buf. The previously mentioned commit modified
the au_read_buf() implementation to match the function pointer, but not
au_read_buf16(). This results in a compiler warning for MIPS
db1xxx_defconfig builds:
drivers/mtd/nand/raw/au1550nd.c:443:57:
warning: pointer type mismatch in conditional expression
Fix this by updating the prototype of au_read_buf16() to take a struct
nand_chip pointer as its first argument, as is expected after commit
7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx()
hooks").
Note that this shouldn't have caused any functional issues at runtime,
since the offset of the struct mtd_info within struct nand_chip is 0
making mtd_to_nand() effectively a type-cast.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx() hooks")
Cc: stable@vger.kernel.org # v4.20+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add new Cadence NAND driver to MTD subsystem
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Change calculating of position page containing BBM
If none of BBM flags are set then function nand_bbm_get_next_page
reports EINVAL. It causes that BBM is not read at all during scanning
factory bad blocks. The result is that the BBT table is build without
checking factory BBM at all. For Micron flash memories none of these
flags are set if page size is different than 2048 bytes.
Address this regression by:
- adding NAND_BBM_FIRSTPAGE chip flag without any condition. It solves
issue only for Micron devices.
- changing the nand_bbm_get_next_page_function. It will return 0
if no of BBM flag is set and page parameter is 0. After that modification
way of discovering factory bad blocks will work similar as in kernel
version 5.1.
Cc: stable@vger.kernel.org
Fixes: f90da7818b (mtd: rawnand: Support bad block markers in first, second or last page)
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
* Fixing typos
* Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
* Macronix: new controller driver
* Omap2: Fixing the number of bitflips returned
* Brcmnand: Fix a pointer not iterating over all the page chunks
* W90x900: Driver removed
* Onenand: Fix a memory leak
* Sharpsl: Missing include guard
* STM32: Avoid warnings when building with W=1
* Ingenic: Fix a coccinelle warning
* r852: Call a helper to simplify the code
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl1ny0EACgkQJWrqGEe9
VoSToQf9Gk13+TPg8oFu6tlmxuQlNU5Dpc+4Hmiahzb1IWwo9Deh2VtZaeWLqPob
uAisb1HByUD0shgoG6cgmVajULlFpmTdfwBQCPR1Wgvq5pejoOC1MQOMexaZ7Gjx
cj4DZEk15FFSR7/zSsN78kFDLFh590hUGfBLW55qE69M5xphmb42BVQUFn44Q/N2
yBvqwUQO/h8TsOS4FXGNc1X0U2/wYQQSOZ6grN3x105cY8Rp05T15a+Qxu22cBem
5IqPY4dwOTXjY5l0mHVIiO/Jk/N9bAgMSd1a15VVukiAL3oefH/kNpsI8T5d31f2
uNONC6GhRJj8c3GDmO8gZ6skzTPhIg==
=a6jq
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/for-5.4
NAND core
* Fixing typos
* Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
* Macronix: new controller driver
* Omap2: Fixing the number of bitflips returned
* Brcmnand: Fix a pointer not iterating over all the page chunks
* W90x900: Driver removed
* Onenand: Fix a memory leak
* Sharpsl: Missing include guard
* STM32: Avoid warnings when building with W=1
* Ingenic: Fix a coccinelle warning
* r852: Call a helper to simplify the code
omap_elm_correct_data() returns the number of bitflips for the whole
page. This is wrong, it should return the maximum number of bitflips
found in each ECC step.
In my case with a 4k page size NAND mtcdore reported -EUCLEAN with
only 12 bitflips on a page where we could correct up to 128 bits per
page (provided they are distributed equally on the 8 ECC steps)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In brcmstb_nand_verify_erased_page(), the ECC chunk pointer calculation
while correcting erased page bitflips is wrong, fix it.
Fixes: 02b88eea9f ("mtd: brcmnand: Add check for erased page bitflips")
Signed-off-by: Claire Lin <claire.lin@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ARM w90x900 platform is getting removed, so this driver is obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a driver for Macronix raw NAND controller.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In nand_scan_bbt(), a temporary buffer 'buf' is allocated through
vmalloc(). However, if check_create() fails, 'buf' is not deallocated,
leading to a memory leak bug. To fix this issue, free 'buf' before
returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In onenand_scan(), if CONFIG_MTD_ONENAND_VERIFY_WRITE is defined,
'this->verify_buf' is allocated through kzalloc(). However, it is not
deallocated in the following execution, if the allocation for
'this->oob_buf' fails, leading to a memory leak bug. To fix this issue,
free 'this->verify_buf' before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Variable ret is being initialized with a value that is never read
and ret is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c:330:1-9: WARNING: Use devm_platform_ioremap_resource for cs -> base
Use devm_platform_ioremap_resource helper which wraps
platform_get_resource() and devm_ioremap_resource() together.
Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci
Fixes: c403ec33b6 ("mtd: rawnand: ingenic: Fix ingenic_ecc dependency")
CC: Paul Cercueil <paul@crapouillou.net>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Fix Micron driver as some chips enable internal ECC correction
during their discovery while they advertize they do not have any.
Hyperbus:
- Restrict the build to only ARM64 SoCs (and compile testing) which is
what should have been done since the beginning.
- Fix Kconfig issue by selection something instead of implying it.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl1E0XAACgkQJWrqGEe9
VoSVXAf/XyLI00EIj3L2KF8K8iYLPRN+lfbeN/YrFvFd9WYhyjY82NKQ/7A1WVjB
k5VIJx4StnhvVBFj/amviK4NycZcJ8GXz5eQvd5oQYRP5pZ9rBBeed/7QAdQ1uEJ
s8yZyFZKQblFyqTISDsfAmiRmwPipAn5TrBRPvpN094tSxoz8MB4SLvRsUy4FIrr
zj6wGrIbSu2x/G3KUw7yTDAfL9QOdgHaCnmM04TOndoDPC+38yVs8ca/67AP44Ni
j0cYivMZhVpavx2n3G01WUiyXAgkDilaG3F+Tn6754zxfQhJM5tVzZOiwSCBI9FS
Cg2dgcRXfPlJJuD5Vs7aPFIGJHLEFg==
=TWEV
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"NAND:
- Fix Micron driver as some chips enable internal ECC correction
during their discovery while they advertize they do not have any.
Hyperbus:
- Restrict the build to only ARM64 SoCs (and compile testing) which
is what should have been done since the beginning.
- Fix Kconfig issue by selection something instead of implying it"
* tag 'mtd/fixes-for-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: hyperbus: Add hardware dependency to AM654 driver
mtd: hyperbus: Kconfig: Fix HBMC_AM654 dependencies
mtd: rawnand: micron: handle on-die "ECC-off" devices correctly
Some devices are not supposed to support on-die ECC but experience
shows that internal ECC machinery can actually be enabled through the
"SET FEATURE (EFh)" command, even if a read of the "READ ID Parameter
Tables" returns that it is not.
Currently, the driver checks the "READ ID Parameter" field directly
after having enabled the feature. If the check fails it returns
immediately but leaves the ECC on. When using buggy chips like
MT29F2G08ABAGA and MT29F2G08ABBGA, all future read/program cycles will
go through the on-die ECC, confusing the host controller which is
supposed to be the one handling correction.
To address this in a common way we need to turn off the on-die ECC
directly after reading the "READ ID Parameter" and before checking the
"ECC status".
Cc: stable@vger.kernel.org
Fixes: dbc44edbf8 ("mtd: rawnand: micron: Fix on-die ECC detection logic")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It has been replaced with the newer Ingenic NAND driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/mtd/nand/onenand/onenand_base.c: In function ‘onenand_check_features’:
drivers/mtd/nand/onenand/onenand_base.c:3264:17: warning: this statement may fall through [-Wimplicit-fallthrough=]
this->options |= ONENAND_HAS_NOP_1;
drivers/mtd/nand/onenand/onenand_base.c:3265:2: note: here
case ONENAND_DEVICE_DENSITY_4Gb:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Cc: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a goto from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put under a new goto to put
the node at a loop exit.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a goto from the middle of the loop, there is no
put, thus causing a memory leak. Hence add an of_node_put before the
goto.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch solves warnings detected by setting W=1 when building.
Warnings type detected:
drivers/mtd/nand/raw/stm32_fmc2_nand.c: In function ‘stm32_fmc2_calc_timings’:
drivers/mtd/nand/raw/stm32_fmc2_nand.c:1417:23: warning: comparison is
always false due to limited range of data type [-Wtype-limits]
else if (tims->twait > FMC2_PMEM_PATT_TIMING_MASK)
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Cc: stable@vger.kernel.org
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
While I was tempted to move it to admin-guide, as some docs
there are more userspace-faced, there are some very technical
discussions about memory error correction code from the Kernel
implementer's PoV. So, let's place it inside the driver-api
book.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename the mtd documentation files to ReST, add an
index for them and adjust in order to produce a nice html
output via the Sphinx build system.
It should be noticed that Sphinx doesn't handle very well
URLs with dots in the middle. Thankfully, internally, the '.'
char is translated to %2E, so we can jus use %2E instead of
dots, and this will work fine on both text and processed files.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0qLr4ACgkQJWrqGEe9
VoQVCwf/ZCG5CldS3cs6B68kMJoZ/rJyJxBnxtIhffda2vw1KG/12o6XaDO9xA/R
EwYrOTzlYZxzCZsNvWyHepG3Kj3d38CJ52ZqhavjpihwMlKKOgW/K39xuKWCrfxS
sVMLz/UdrcsQfcPGAy7DSyqhzRAtupNxngCdEkIIMGFZWsv4uZfOFEGMrzUJ5RYN
/okIyUE7Iz0dRq1/KXSl365V1MS8QP2eHFuHrUd38+kJ8TJnQjXX3Bmdul4aNTx+
HIIpykovoAn5BZ0YA4lJL90zVoDOWysARwHIAMDvJa8zS0wDTU16Tj2M6AQK+a4x
hbIOOkeX0hTKpJvy7/khli5y1bn2mw==
=L+tV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"This contains the following changes for MTD:
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
- fix BCH ECC layout for large page NAND parts
- fallback to detected ecc-strength, ecc-step-size
- when oops in progress use pio and interrupt polling
- code refactor code to introduce helper functions
- add support for v7.3 controller
- FSMC:
- use nand_op_trace for operation tracing
- GPMI:
- move all driver code into single file
- various cleanups (including dmaengine changes)
- use runtime PM to manage clocks
- implement exec_op
- MTK:
- correct low level time calculation of r/w cycle
- improve data sampling timing for read cycle
- add validity check for CE# pin setting
- fix wrongly assigned OOB buffer pointer issue
- re-license MTK NAND driver as Dual MIT/GPL
- STM32:
- manage the get_irq error case
- increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control"
* tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (60 commits)
mtd: concat: implement _is_locked mtd operation
mtd: concat: refactor concat_lock/concat_unlock
mtd: abi: do not use C++ style comments in uapi header
mtd: afs: remove unneeded NULL check
mtd: rawnand: stm32_fmc2: increase DMA completion timeouts
mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()
mtd: hyperbus: Add driver for TI's HyperBus memory controller
mtd: spinand: read returns badly if the last page has bitflips
mtd: spinand: Add initial support for Paragon PN26G0xA
mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL
mtd: rawnand: gpmi: remove double assignment to block_size
dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support
mtd: rawnand: brcmnand: Add support for v7.3 controller
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
mtd: Add flag to indicate panic_write
mtd: rawnand: Add Macronix NAND read retry support
mtd: onenand: Avoid fall-through warnings
mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
mtd: spinand: Add support for two-byte device IDs
...
Allwinner NAND controllers can make use of DMA to enhance the I/O
throughput thanks to ECC pipelining. DMA handling with A23/A33 NAND IP
is a bit different than with the older SoCs, hence the introduction of
a new compatible to handle:
* the differences between register offsets,
* the burst length change from 4 to minimum 8,
* manage SRAM accesses through MBUS with extra configuration.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This reverts commit c49836f05a.
The commit is wrong and its approach actually does not work. Let's
revert it in order to add the feature with a clean patch.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If MTD_NAND_JZ4780 is y and MTD_NAND_JZ4780_BCH is m,
which select CONFIG_MTD_NAND_INGENIC_ECC to m, building fails:
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_remove':
ingenic_nand.c:(.text+0x177): undefined reference to `ingenic_ecc_release'
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_ecc_correct':
ingenic_nand.c:(.text+0x2ee): undefined reference to `ingenic_ecc_correct'
To fix that, the ingenic_nand and ingenic_ecc modules have been fused
into one single module.
- The ingenic_ecc.c code is now compiled in only if
$(CONFIG_MTD_NAND_INGENIC_ECC) is set. This is now a boolean instead
of tristate.
- To avoid changing the module name, the ingenic_nand.c file is moved to
ingenic_nand_drv.c. Then the module name is still ingenic_nand.
- Since ingenic_ecc.c is no more a module, the module-specific macros
have been dropped, and the functions are no more exported for use by
the ingenic_nand driver.
Fixes: 15de8c6efd ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Hulk Robot <hulkci@huawei.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 1Gb Macronix chip can have a maximum of 20 bad blocks, while
the 2Gb version has twice as many blocks and therefore the maximum
number of bad blocks is 40.
The 4Gb GigaDevice GD5F4GQ4xA has twice as many blocks as its 2Gb
counterpart and therefore a maximum of 80 bad blocks.
Fixes: 377e517b5f ("mtd: nand: Add max_bad_eraseblocks_per_lun info to memorg")
Reported-by: Emil Lenngren <emil.lenngren@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When the system is overloaded, DMA data transfer completion occurs after
100ms. Increase the timeouts to let it the time to complete.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace kmalloc() by a memset() followed with a kzalloc().
There is a recommendation to use zeroing allocator
rather than allocator followed by memset(0) in
./scripts/coccinelle/api/alloc/zalloc-simple.cocci
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In case of the last page containing bitflips (ret > 0),
spinand_mtd_read() will return that number of bitflips for the last
page while it should instead return max_bitflips like it does when the
last page read returns with 0.
Signed-off-by: Weixiong Liao <liaoweixiong@allwinnertech.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: stable@vger.kernel.org
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It is wanted to use MTK NAND driver with GPL-2.0 or MIT license.
But now it is only licensed as GPL-2.0, so re-license it as dual
MIT/GPL.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Acked-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Wen Yang <yellowriver2010@hotmail.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: RogerCC Lin <rogercc.lin@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The variable block_size is being assigned to itself and to
geo->ecc_chunk_size. Clean up the double assignment by removing
the assignment to itself.
Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This change adds support for brcm NAND v7.3 controller. This controller
uses a newer version of flash_dma engine and change mostly implements
these differences.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Refactored NAND ECC and CMD address configuration code to use helper
functions.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If mtd_oops is in progress, switch to polling during NAND command
completion instead of relying on DMA/interrupts so that the mtd_oops
buffer can be completely written in the assigned NAND partition.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for Macronix NAND read retry.
Macronix NANDs support specific read operation for data recovery,
which can be enabled with a SET_FEATURE.
Driver checks byte 167 of Vendor Blocks in ONFI parameter page table
to see if this high-reliability function is supported.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NOTICE THAT:
"...we don't know whether we need fallthroughs or breaks here and this
is just a change to avoid having new warnings when switching to
-Wimplicit-fallthrough but this change might be entirely wrong."[1]
See the original thread of discussion here:
https://lore.kernel.org/patchwork/patch/1036251/
So, in preparation to enabling -Wimplicit-fallthrough, this patch silences
the following warnings:
drivers/mtd/nand/onenand/onenand_base.c: In function ‘onenand_check_features’:
drivers/mtd/nand/onenand/onenand_base.c:3264:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ONENAND_IS_DDP(this))
^
drivers/mtd/nand/onenand/onenand_base.c:3284:2: note: here
case ONENAND_DEVICE_DENSITY_2Gb:
^~~~
drivers/mtd/nand/onenand/onenand_base.c:3288:17: warning: this statement may fall through [-Wimplicit-fallthrough=]
this->options |= ONENAND_HAS_UNLOCK_ALL;
drivers/mtd/nand/onenand/onenand_base.c:3290:2: note: here
case ONENAND_DEVICE_DENSITY_1Gb:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Also, notice that this patch doesn't change any functionality. See the
most recent thread of discussion here:
https://lore.kernel.org/patchwork/patch/1077395/
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
[1] https://lore.kernel.org/lkml/20190509085318.34a9d4be@xps13/
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The GigaDevice GD5F1GQ4UFxxG SPI NAND is in current production devices
and, while it has the same logical layout as the E-series devices,
it differs in the SPI interfacing in significant ways.
This support is contingent on previous commits to:
* Add support for two-byte device IDs
* Define macros for page-read ops with three-byte addresses
http://www.gigadevice.com/datasheet/gd5f1gq4xfxxg/
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This change supports nand-ecc-step-size and nand-ecc-strength fields in
brcmnand DT node to be optional.
see: Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
If both nand-ecc-strength and nand-ecc-step-size are not specified in
device tree node for NAND, raw NAND layer does detect ECC information by
reading ONFI extended parameter page for parts using ONFI >= 2.1.
In case of non-ONFI NAND parts there could be a nand_id table entry with
ECC information. If there is valid device tree entry for nand-ecc-strength
and nand-ecc-step-size fields it still shall override the detected values.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The gpmi driver performance suffers from NAND operations being split
in multiple small DMA transfers. This has been forced by the NAND layer
in the former days, but now with exec_op we can use the controller as
intended.
With this patch gpmi_nfc_exec_op becomes the main entry point to NAND
operations. Here all instructions are collected and chained as separate
DMA transfers. In the end whole chain is fired and waited to be
finished. gpmi_nfc_exec_op only does the hardware operations, bad block
marker swapping and buffer scrambling is done by the callers. It's worth
noting that the nand_*_op functions always take the buffer lengths for
the data that the NAND chip actually transfers. When doing BCH we have
to calculate the net data size from the raw data size in some places.
This patch has been tested with 2048/64 and 2048/128 byte NAND on
i.MX6q. mtd_oobtest, mtd_subpagetest and mtd_speedtest run without
errors. nandbiterrs, nandpagetest and nandsubpagetest userspace tests
from mtdutils run without errors and UBIFS can successfully be mounted.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver uses the flags parameter in dmaengine_prep_slave_sg() for
custom flags, but still uses the dmaengine specific names of the flags.
Do a little bit better and at least give the flag a custom name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver can do PIO transfers. A pointer to the PIO words
to transfer is passed in the struct scatterlist * argument of
dmaengine_prep_slave_sg(). It's quite ugly and non obvious to cast
u32 * to struct scatterlist * each time when calling
dmaengine_prep_slave_sg(), so add a static inline wrapper function
to be called by the user along with a description what is going on.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The DMA_PREP_INTERRUPT flag is no longer needed by the mxs DMA driver,
drop it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The gpmi driver aggressively en/disables the clocks between operations
which has significant performance cost. Use runtime PM to get rid of
this bottleneck.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The i.MX23 specific option read code is called right after nand_scan. We
can rely on the NAND core having disabled the chipselect, so there's no
point in restoring the original chip select after NAND operations. Drop
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gpmi_ecc_read_page_data uses the page parameter only for a debug printf,
so we can drop the parameter and the debug printf. Moving the oob
delivery from gpmi_ecc_read_page_data to gpmi_ecc_read_page makes the
oob_required parameter unnecessary aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The driver calls nand_read_page_op without a buffer passed and then
calls chip->legacy.read_buf to read the buffer afterwards which is
the same as passing the buffer nand_read_page_op in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
this->page_buffer_virt and this->payload_virt are always set to the same
value, so drop the former and just use the latter. Same for
this->page_buffer_virt and this->payload_virt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The "private" member of struct gpmi_nand_data isn't used anywhere.
Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This moves the whole driver into a single C file. The filename gpmi-lib
implies that it implements library functions, but in fact there are
several cases where functions in gpmi-lib.c call back into functions in
gpmi-nand.c. With this one has to constantly jump between those two
files, so moving it into a single file improves readability, even when
the file gets quite large.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the different operation tracing functions with a call to
nand_op_trace.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The NAND core has a NAND operation tracing function, but it can only
be used by drivers using the generic option parser from the NAND core.
Export the tracing function as a static inline function in rawnand.h
so that drivers implementing exec_op directly do not have to write their
own operation tracing.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
One main goal of the function mtk_nfc_update_ecc_stats is to check
whether sectors are all empty. If they are empty, set these sectors's
data buffer and OOB buffer as 0xff.
But now, the sector OOB buffer pointer is wrongly assigned. We always
do memset from sector 0.
To fix this issue, pass start sector number to make OOB buffer pointer
be properly assigned.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, we only check how many CE# pins are set in device tree.
But it should be necessary to check whether CE# pin setting is
duplicated or if CE# pin index exceeds the maximum CE# number that
controller supports.
So, add validity check to avoid these invalid settings.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, we expand RE# low level time by choosing the max value
between RE# pulse width and RE# access time, and sample data at the
rising edge of RE#.
Then, if RE# access time is bigger than RE# pulse width, the real
read cycle time may be more than NAND SPEC required. This makes
read performance be worse than that expected.
This patch improves data sampling timing by calculating RE# low level
time according to RE# pulse width. If RE# access time is bigger than
RE# pulse width, then delay sampling data timing.
The result of contrast test base on MT2712 evaluat board is as follow.
nand: Micron MT29F16G08ADBCAH4
nand: 2048 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224
NFI 2x clock rate: 124800000 HZ.
Read speed without this patch:
mtd_speedtest: page read speed is 14012 KiB/s
mtd_speedtest: 2 page read speed is 14860 KiB/s
Read speed with this patch:
mtd_speedtest: page read speed is 18724 KiB/s
mtd_speedtest: 2 page read speed is 18713 KiB/s
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
At present, the flow of calculating AC timing of read/write cycle in SDR
mode is that:
At first, calculate high hold time which is valid for both read and write
cycle using the max value between tREH_min and tWH_min.
Secondly, calculate WE# pulse width using tWP_min.
Thridly, calculate RE# pulse width using the bigger one between tREA_max
and tRP_min.
But NAND SPEC shows that Controller should also meet write/read cycle time.
That is write cycle time should be more than tWC_min and read cycle should
be more than tRC_min. Obviously, we do not achieve that now.
This patch corrects the low level time calculation to meet minimum
read/write cycle time required. After getting the high hold time, WE# low
level time will be promised to meet tWP_min and tWC_min requirement,
and RE# low level time will be promised to meet tREA_max, tRP_min and
tRC_min requirement.
Fixes: edfee3619c ("mtd: nand: mtk: add ->setup_data_interface() hook")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The way oobregion->offset is derived for large page NAND parts is
wrong, fixes it.
Fixes: ef5eeea6e9 ("mtd: nand: brcm: switch to mtd_ooblayout_ops")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Used in several S5PV210-based Galaxy S devices, among them SGH-T959V,
SGH-T959P, SGH-T839, and SPH-D700.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sometimes the exec_op parser does not choose the optimal pattern if
multiple patterns with optional elements are available. Since the stack
automatically splits operations in multiple exec_op calls, a non-optimal
pattern gets broken up into multiple calls. E.g. an OOB read using the
vf610 driver:
nand: executing subop:
nand: ->CMD [0x00]
nand: ->ADDR [5 cyc: 00 08 ea 94 02]
nand: ->CMD [0x30]
nand: ->WAITRDY [max 200000 ms]
nand: DATA_IN [64 B]
nand: executing subop:
nand: CMD [0x00]
nand: ADDR [5 cyc: 00 08 ea 94 02]
nand: CMD [0x30]
nand: WAITRDY [max 200000 ms]
nand: ->DATA_IN [64 B]
However, the vf610 driver has a pattern which can execute the complete
command in a single go...
This patch makes sure that the longest matching pattern is chosen
instead of the first (potentially only partial) match. With this
change the vf610 reads the OOB in a single exec_op call:
nand: executing subop:
nand: ->CMD [0x00]
nand: ->ADDR [5 cyc: 00 08 c0 1d 00]
nand: ->CMD [0x30]
nand: ->WAITRDY [max 200000 ms]
nand: ->DATA_IN [64 B]
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0Pwk0ACgkQJWrqGEe9
VoS8nwf7B76jN39/g32Hfp4JT/B7cntrHzTGxfUT9NAhKa4MaI7FOU2eeTryaVdO
32OJlttV+r0Fu6p+In1VXCk4j1YlkcOaxqB1VXsMEaQ+Vt8ONVTbJX/cqyGC/ogq
MZlO8Rys4MGmq7vRiZ+1SD8lOV4qXgmX3D38NjUQ1oCAMCCgJgkWYFV2tv9Eie09
2CCT3IBFj+D34qaBiM+qocGtnzWfB9477A6ZeI4BwjUe1ZtoEYeIOrCXWiywabjM
msHRN1tNt5kfINnx0TkQFcnpbdDo5tMyTHCkEQt5Ewdae4vyCv7xTHTCZEttC7Ic
Rx2yONzrZGQVP4c27y22K954C1jGcg==
=ZiPm
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Set the raw NAND number of targets to the right value
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes
* tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes
mtd: rawnand: initialize ntargets with maxchips
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program see the file copying if not
write to the free software foundation 59 temple place suite 330
boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.832876118@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version you should have received a copy of the
gnu general public license along with this program if not write to
the free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not write to the free software foundation inc 59 temple place suite
330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 42 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.259718220@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is free software you can redistribute it and or modify it
under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this file is distributed in the hope that it will be
useful but without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this file if not
write to the free software foundation inc 59 temple place suite 330
boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.735098607@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
memorg->ntargets is initialized with '1'. It should be initialized with
the maxchips argument from nand_scan() instead. Otherwise multi chip
support errors out on the secondary chip selects when trying to call
nand_reset() on them:
WARNING: CPU: 0 PID: 1 at drivers/mtd/nand/raw/internals.h:114
nand_reset_op+0x194/0x1c4
With this memorg->ntargets is initialized with the maximum number of
chip selects supported by the driver. After having detected the number
of actually connected chips memory->ntargets is updated with that
number.
Fixes: 32813e2884 ("mtd: rawnand: Get rid of chip->numchips")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This prepares to move CONFIG_OPTIMIZE_INLINING from x86 to a common
place. We need to eliminate potential issues beforehand.
Kbuild test robot has never reported -Wmaybe-uninitialized warning for
this probably because vf610_nfc_run() is inlined by the x86 compiler's
inlining heuristic.
If CONFIG_OPTIMIZE_INLINING is enabled for a different architecture and
vf610_nfc_run() is not inlined, the following warning is reported:
drivers/mtd/nand/raw/vf610_nfc.c: In function `vf610_nfc_cmd':
drivers/mtd/nand/raw/vf610_nfc.c:455:3: warning: `offset' may be used uninitialized in this function [-Wmaybe-uninitialized]
vf610_nfc_rd_from_sram(instr->ctx.data.buf.in + offset,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
nfc->regs + NFC_MAIN_AREA(0) + offset,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
trfr_sz, !nfc->data_access);
~~~~~~~~~~~~~~~~~~~~~~~~~~~
Link: http://lkml.kernel.org/r/20190423034959.13525-6-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
* Avoid crossing 4K address boundary on read/write
* Add support for Intel Comet Lake SPI serial flash
-----BEGIN PGP SIGNATURE-----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=HXap
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from
generic functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
- Switch to ->exec-op().
- meson:
- Misc cleanups and fixes.
- New OOB layout.
- Sunxi:
- A23/A33 NAND DMA support.
- Ingenic:
- Full reorganization and cleanup.
- Clear separation between NAND controller and ECC engine.
- Support JZ4740 an JZ4725B.
- Denali:
- Clear controller/chip separation.
- ->exec_op() migration.
- Various cleanups.
- fsl_elbc:
- Enable software ECC support.
- Atmel:
- Sam9x60 support.
- GPMI:
- Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
- Avoid crossing 4K address boundary on read/write
- Add support for Intel Comet Lake SPI serial flash"
* tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: part: fix incorrect format specifier for an unsigned long long
mtd: lpddr_cmds: Mark expected switch fall-through
mtd: phram: Mark expected switch fall-throughs
mtd: cfi_cmdset_0002: Mark expected switch fall-throughs
mtd: cfi_util: mark expected switch fall-throughs
MAINTAINERS: MTD Git repository is hosted on kernel.org
MAINTAINERS: Update jffs2 entry
mtd: afs: add v2 partition parsing
mtd: afs: factor the IIS read into partition parser
mtd: afs: factor footer parsing into the v1 part parsing
mtd: factor out v1 partition parsing
mtd: afs: simplify partition detection
mtd: afs: simplify partition parsing
mtd: partitions: Add OF support to AFS partitions
mtd: partitions: Add AFS partitions DT bindings
mtd: afs: Move AFS partition parser to parsers subdir
mtd: maps: Make uclinux_ram_map static
mtd: maps: Allow MTD_PHYSMAP with MTD_RAM
MAINTAINERS: Add myself as MTD maintainer
MAINTAINERS: Remove my name from the MTD and NAND entries
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Since the migration of the driver to stop using the legacy
->select_chip() hook, there is nothing deselecting the target anymore,
thus the selection is not forced at the next access. Ensure the ND_RUN
bit and the interrupts are always in a clean state.
Cc: Daniel Mack <daniel@zonque.org>
Cc: stable@vger.kernel.org
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Stop using the legacy interface.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We will need struct nand_controller soon, so more stuff need to
be parts of struct nandsim.
While we are here, rename "nand" to "ns" to use the same naming scheme
everywhere in nandsim.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
According to the datasheet of some Cypress SLC NANDs, the bad
block markers can be in the first, second or last page of a block.
So let's check all three locations.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It is known that some ESMT SLC NANDs have been shipped
with the factory bad block markers in the first or last page
of the block, instead of the first or second page. To be on
the safe side, let's check all three locations.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently supported bad block marker positions within the block are:
* in first page only
* in last page only
* in first or second page
Some ESMT NANDs are known to have been shipped by the manufacturer
with bad block markers in the first or last page, instead of the
first or second page.
Also the datasheets for Cypress/Spansion/AMD NANDs claim that the
first, second *and* last page needs to be checked.
Therefore we make it possible to set NAND_BBM_FIRSTPAGE,
NAND_BBM_SECONDPAGE and NAND_BBM_LASTPAGE independently in any
combination.
To simplify the code, the logic to evaluate the flags is moved to a
a new function nand_bbm_get_next_page().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
To be able to check and set bad block markers in the first and
second page of a block independently of each other, we create
separate flags for both cases.
Previously NAND_BBM_SECONDPAGE meant, that both, the first and the
second page were used. With this patch NAND_BBM_FIRSTPAGE stands for
using the first page and NAND_BBM_SECONDPAGE for using the second
page.
This patch is only for preparation of subsequent changes and does
not implement the logic to actually handle both flags separately.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to the chip struct,
as we did it for rawnand.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to nand_chip.options
and nand_chip.badblockpos.
As this chip-specific information is not directly related to the
bad block table (BBT), we also rename the flags to NAND_BBM_*.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Documentation/scheduler/completion.txt states:
Calling init_completion() on the same completion object twice is
most likely a bug as it re-initializes the queue to an empty queue and
enqueued tasks could get "lost" - use reinit_completion() in that case,
but be aware of other races.
Initialize nfc->completion in meson_nfc_probe using init_completion and
change the call in meson_nfc_queue_rb to reinit_completion so the logic
matches what the documentation suggests.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This simplifies the code because it gets rid of the casts to an
u8-pointer when passing "info_buf" from struct meson_nfc_nand_chip.
Also it gets rid of the cast of the u8 databuf pointer to a void
pointer.
The logic inside meson_nfc_dma_buffer_setup() doesn't care about the
pointer types themselves because it only passes them to dma_map_single
which accepts a void pointer.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the of_property_count_elems_of_size() helper instead of open-coding
it's logic. As a bonus this will now error out if the "reg" property
values use an incorrect size (anything other than sizeof(u32)).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the recently introduced struct_size macro instead of open-coding
it's logic.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since the migration of the driver to stop using the legacy
->select_chip() hook, the marvell_nfc_select_chip() helper has been
'renamed' to marvell_nfc_select_target(). Update a left-over reference
to this helper in a comment in the ->resume() path.
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Allwinner NAND controllers can make use of DMA to enhance the I/O
throughput thanks to ECC pipelining. DMA handling with A23/A33 NAND IP
is a bit different than with the older SoCs, hence the introduction of
a new compatible to handle:
* the differences between register offsets,
* the burst length change from 4 to minimum 8,
* drive SRAM accesses through the AHB bus instead of the MBUS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Before the introduction of A33 NAND DMA support, let's use a platform
data structure for parameters that will differ. Right now, there is
only one compatible with one data structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix sparse warning:
drivers/mtd/nand/raw/ingenic/ingenic_nand.c:140:32: warning:
symbol 'jz4725b_ooblayout_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Eliminate the following reports from 'scripts/checkpatch.pl --strict'.
CHECK: Prefer kernel type 'u8' over 'uint8_t'
CHECK: Prefer kernel type 'u32' over 'uint32_t'
CHECK: Alignment should match open parenthesis
I slightly changed denali_check_erased_page() to shorten it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the runtime-detected denali->nbanks instead of hard-coded
DENALI_NR_BANKS (=4).
The actual number of banks depends on the IP configuration, and
can be less than DENALI_NR_BANKS. It is pointless to touch
registers of unsupported banks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, this driver sticks to the legacy NAND model because it was
upstreamed before commit 2d472aba15 ("mtd: nand: document the NAND
controller/NAND chip DT representation"). However, relying on the
dummy_controller is already deprecated.
Switch over to the new controller/chip representation.
The struct denali_nand_info has been split into denali_controller
and denali_chip, to contain the controller data, per-chip data,
respectively.
One problem is, this commit changes the DT binding. So, as always,
the backward compatibility must be taken into consideration.
In the new binding, the controller node expects
#address-cells = <1>;
#size-cells = <0>;
... since the child nodes represent NAND chips.
In the old binding, the controller node may have subnodes, but they
are MTD partitions.
The denali_dt_is_legacy_binding() exploits it to distinguish old/new
platforms.
Going forward, the old binding is only allowed for existing DT files.
I updated the binding document.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As Documentation/process/coding-style.rst says, choose label names
which say what the goto does. The out_<action> label style is already
used in denali_dt.c. Rename likewise for denali_pci.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use 'bool' type for the following boolean parameters.
- write (write or read?)
- dma_avail (DMA engine available or not?)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since (u32 *) can accept an opaque pointer, the explicit casting
from (void *) to (u32 *) is redundant. Change the function argument type
to remove the casts.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Denali IP adopts the syndrome page layout (payload and ECC are
interleaved). The *_page_raw() and *_oob() callbacks are complicated
because they must hide the underlying layout used by the hardware,
and always return contiguous in-band and out-of-band data.
The Denali IP cannot reuse nand_{read,write}_page_raw_syndrome()
in nand_base.c because its hardware ECC engine skips some of first
bytes in OOB. That is why this driver implements specially-crafted
*_page_raw() and *_oob() hooks.
Currently, similar code is duplicated to reorganize the data layout.
For example, denali_read_page_raw() and denali_write_page_raw() look
almost the same. The complexity is partly due to the DMA transfer
used for better performance of *_page_raw() accessors.
On second thought, we do not need to care about their performance
because MTD_OPS_RAW is rarely used.
Let's focus on code cleanups rather than the performance. This commit
removes the internal buffer for DMA, and factors out as much code as
possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
With the recent refactoring, the NAND driver hooks now take a pointer
to nand_chip. Add to_denali() in order to convert (struct nand_chip *)
to (struct denali_nand_info *) directly. It is more useful than the
current mtd_to_denali().
I changed some helper functions to take (struct nand_chip *). This will
avoid pointer conversion back and forth, and ease further development.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Wrong copy/paste from the previous block, the error message should
refer to #size-cells instead of #address-cells.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Move the code that choses ECC into _attach_chip, which is executed only
after the chip->ecc.* properties were loaded from device-tree. This way
we know which ECC method was chosen by the device-tree and can set
methods appropriately.
The chip->ecc.*page methods should be set to fsl_elbc_*page only in HW
ECC mode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Move the fsl_elbc_attach_chip function after the definitions of
fsl_elbc_read_page and friends in preparation for the next patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When enabling CONFIG_MTD_NAND_ECC_SW_BCH as a module, the
MTD_NAND_ECC_SW_BCH depends on MTD_NAND, but the module controlled by
MTD_NAND links against the module controlled by MTD_NAND_ECC_SW_BCH.
This leads to the following link failure.
aarch64-linux-gnu-ld: drivers/mtd/nand/raw/nand_base.o: in function `nand_cleanup':
../drivers/mtd/nand/raw/nand_base.c:5886: undefined reference to `nand_bch_free'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5886:(.text+0x9928): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `nand_bch_free'
aarch64-linux-gnu-ld: drivers/mtd/nand/raw/nand_base.o: in function `nand_set_ecc_soft_ops':
../drivers/mtd/nand/raw/nand_base.c:5093: undefined reference to `nand_bch_calculate_ecc'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5093:(.text+0xe914): relocation truncated to fit: R_AARCH64_ADR_PREL_PG_HI21 against undefined symbol `nand_bch_calculate_ecc'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5093: undefined reference to `nand_bch_calculate_ecc'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5094: undefined reference to `nand_bch_correct_data'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5094:(.text+0xe934): relocation truncated to fit: R_AARCH64_ADR_PREL_PG_HI21 against undefined symbol `nand_bch_correct_data'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5094: undefined reference to `nand_bch_correct_data'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5148: undefined reference to `nand_bch_init'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5148:(.text+0xebbc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `nand_bch_init'
Rework CONFIG_MTD_NAND_ECC_SW_BCH from tristate to bool,
and then link the nand_bch.o file into nand.ko if its enabled.
Fixes: 51ef1d0b2095 ("mtd: nand: Clarify Kconfig entry for software BCH ECC algorithm")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Prepare changes that will lay in this file to better express what is
NAND related and what is not in menuconfig.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
MTD_NAND is large and encloses much more than what the symbol is
actually used for: raw NAND. Clarify the symbol by naming it
MTD_RAW_NAND instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This list is a mess, while some items should probably not be in the
raw/ sub-directory, others are definitely at the right place but not
with the right description. Write uniform titles and group IPs by
vendor.
NAND controllers will appear under the list named "Raw/parallel NAND
flash controllers" while the other drivers will appear under
"Misc". Software ECC engines will later be moved out of the raw/
directory.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The software Hamming ECC correction implementation is referred as
MTD_NAND_ECC which is too generic. Rename it
MTD_NAND_ECC_SW_HAMMING. Also rename MTD_NAND_ECC_SMC which is an
SMC quirk in the Hamming implementation as
MTD_NAND_ECC_SW_HAMMING_SMC.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no point in having two distinct entries, merge them and
rename the symbol for more clarity: MTD_NAND_ECC_SW_BCH
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
nand_device embeds a nand_ecc_req object which contains the minimum
strength and step-size required by the NAND device.
Drop the chip->ecc_{strength,step}_ds fields and use
chip->base.eccreq.{strength,step_size} instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The same information is provided by nanddev_ntargets().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The target size can now be returned by nanddev_get_targetsize(). Get
rid of the chip->chipsize field and use this helper instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that we inherit from nand_device, we can use
nand_device->memorg.bits_per_cell instead of having our own field at
the nand_chip level.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
nanddev_mtd_max_bad_blocks() is implemented by the generic NAND layer
and is already doing what we need. Reuse this function instead of
having our own implementation.
While at it, get rid of the ->max_bb_per_die and ->blocks_per_die
fields which are now unused.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Looking at the field names it's hard to tell what ->data_buf, ->pagebuf
and ->pagebuf_bitflips are for. Clarify that by moving those fields
in a sub-struct named pagecache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
We plan to move cache related fields to a pagecache struct in nand_chip
but some drivers access ->pagebuf directly to invalidate the cache
before they start using ->data_buf.
Let's provide an helper that returns a pointer to ->data_buf after
invalidating the cache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In order to use some of the nanddev_xxx() helpers, we need to
initialize the nand_device object embedded in nand_chip using
nanddev_init(). This requires implementing nand_ops.
We also drop useless mtd->xxx initialization when they're already taken
case of by nanddev_init().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
If we want to use the generic NAND layer, we need to have the memorg
struct appropriately filled. Patch the detection code to fill this
struct.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We just have to use nanddev_mtd_max_bad_blocks().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
NAND datasheets usually give the maximum number of bad blocks per LUN
and this number can be used to help upper layers decide how much blocks
they should reserve for bad block handling.
Add a max_bad_eraseblocks_per_lun to the nand_memory_organization
struct and update the NAND_MEMORG() macro (and its users) accordingly.
We also provide a default mtd->_max_bad_blocks() implementation.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Specify the oob layout operation to avoid no oob scheme defined for
some nand flash.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_match_device can return NULL if there is no matching device. Avoid
a potential NULL pointer dereference by checking for the return value
and passing the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The generic layout for BBT markers will most likely overlap with our
ECC bytes in the OOB, so move the BBT markers outside the OOB area.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Ben Nanonote from Qi Hardware expects a specific OOB layout on its
NAND.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The boot ROM of the JZ4725B SoC expects a specific OOB layout on the
NAND, so we use it unconditionally in the ingenic-nand driver.
Also add the jz4725b-bch driver to support the JZ4725B-specific BCH
hardware.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for probing the ingenic-nand driver on the JZ4740 SoC from
Ingenic, and the jz4740-ecc driver to support the JZ4740-specific
ECC hardware.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the 'ecc-engine' standard property instead of the custom
'ingenic,bch-controller' custom property, which is now deprecated.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ingenic-nand driver uses an API provided by the jz4780-bch driver.
This makes it difficult to support other SoCs in the jz4780-bch driver.
To work around this, we separate the API functions from the SoC-specific
code, so that these API functions are SoC-agnostic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The jz4780_bch_init name was confusing, as it suggested that its content
should be executed once at init time, whereas what the function really
does is reset the hardware for a new ECC operation.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The jz4780_nand driver will be modified to handle all the Ingenic
JZ47xx SoCs that the upstream Linux kernel supports (JZ4740, JZ4725B,
JZ4770, JZ4780), so it makes sense to rename it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use SPDX license notifiers instead of GPLv2 license text in the headers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Before adding support for more SoCs and seeing the number of files for
these drivers grow, we move them to their own subfolder to keep it tidy.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
meson_nfc_dma_buffer_setup() is called with the "info" buffer which is
allocated a few lines before using kzalloc(). If
meson_nfc_dma_buffer_setup() fails we need to free the allocated "info"
buffer instead of only freeing it upon success.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
kzalloc() can return NULL if memory could not be allocated. Check the
return value of the kzalloc() call in meson_nfc_read_buf() to make it
consistent with other memory allocations within the meson_nand driver.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The sam9x60 board defines the CCFG_EBICSA register under SFR,
and not as a MATRIX register, as previous boards do.
NAND Flash I/Os are connected to D16–D23, thus
SFR_CCFG_EBICSA.NFD0_ON_D16 is set to 1.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The sam9x60 board defines the CCFG_EBICSA register under SFR,
and not as a MATRIX register, as previous boards do. Add a
more generic name for the EBICSA regmap, as a prerequisite for
sam9x60 nand controller support.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/mtd/nand/raw/diskonchip.c: In function ‘doc_probe’:
./include/linux/printk.h:303:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/diskonchip.c:1479:4: note: in expansion of macro ‘pr_err’
pr_err("DiskOnChip Millennium Plus 32MB is not supported, ignoring.\n");
^~~~~~
drivers/mtd/nand/raw/diskonchip.c:1480:3: note: here
default:
^~~~~~~
drivers/mtd/nand/raw/nandsim.c: In function ‘ns_init_module’:
drivers/mtd/nand/raw/nandsim.c:2254:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
chip->bbt_options |= NAND_BBT_NO_OOB;
drivers/mtd/nand/raw/nandsim.c:2255:2: note: here
case 1:
^~~~
drivers/mtd/nand/raw/nuc900_nand.c: In function ‘nuc900_nand_command_lp’:
./arch/x86/include/asm/io.h:91:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
#define __raw_writel __writel
drivers/mtd/nand/raw/nuc900_nand.c:52:2: note: in expansion of macro ‘__raw_writel’
__raw_writel((val), (dev)->reg + REG_SMCMD)
^~~~~~~~~~~~
drivers/mtd/nand/raw/nuc900_nand.c:196:3: note: in expansion of macro ‘write_cmd_reg’
write_cmd_reg(nand, NAND_CMD_READSTART);
^~~~~~~~~~~~~
drivers/mtd/nand/raw/nuc900_nand.c:197:2: note: here
default:
^~~~~~~
drivers/mtd/nand/raw/omap_elm.c: In function ‘elm_context_restore’:
drivers/mtd/nand/raw/omap_elm.c:512:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
elm_write_reg(info, ELM_SYNDROME_FRAGMENT_4 + offset,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
regs->elm_syndrome_fragment_4[i]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:514:3: note: here
case BCH8_ECC:
^~~~
drivers/mtd/nand/raw/omap_elm.c:517:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
elm_write_reg(info, ELM_SYNDROME_FRAGMENT_2 + offset,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
regs->elm_syndrome_fragment_2[i]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:519:3: note: here
case BCH4_ECC:
^~~~
drivers/mtd/nand/raw/omap_elm.c: In function ‘elm_context_save’:
drivers/mtd/nand/raw/omap_elm.c:466:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
regs->elm_syndrome_fragment_4[i] = elm_read_reg(info,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
ELM_SYNDROME_FRAGMENT_4 + offset);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:468:3: note: here
case BCH8_ECC:
^~~~
drivers/mtd/nand/raw/omap_elm.c:471:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
regs->elm_syndrome_fragment_2[i] = elm_read_reg(info,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
ELM_SYNDROME_FRAGMENT_2 + offset);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:473:3: note: here
case BCH4_ECC:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Introduce a GPMI_IS_MXS() macro to take into account the cases
when mx23 or mx28 are used, which helps readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Stefan Roese <sr@denx.de>
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----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=wIHY
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core MTD changes:
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes:
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting
various controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Check the return code of nand_reset() and nand_readid_op().
- Remove ->legacy.erase and single_erase().
- Simplify the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fix various possible object reference leaks (MTK, JZ4780, Atmel)
- ST:
* Add support for STM32 FMC2 NAND flash controller
- Meson:
* Add support for Amlogic NAND flash controller
- Denali:
* Several cleanup patches
- Sunxi:
* Several cleanup patches
- FSMC:
* Disable NAND on remove()
* Reset NAND timings on resume()
SPI-NAND drivers changes:
- Toshiba:
* Add support for all Toshiba products.
- Macronix:
* Fix ECC status read.
- Gigadevice:
* Add support for GD5F1GQ4UExxG"
* tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd: (64 commits)
mtd: spi-nor: Fix wrong abbreviation HWCPAS
mtd: spi-nor: cadence-quadspi: fix spelling mistake: "Couldnt't" -> "Couldn't"
mtd: spi-nor: Add support for en25qh64
mtd: spi-nor: Add support for MX25V8035F
mtd: spi-nor: Add support for EN25Q80A
mtd: spi-nor: cadence-quadspi: Add support for Octal SPI controller
dt-bindings: cadence-quadspi: Add new compatible for AM654 SoC
mtd: spi-nor: split s25fl128s into s25fl128s0 and s25fl128s1
mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
mtd: spi-nor: Add support for mx25u3235f
mtd: rawnand: denali_dt: remove single anonymous clock support
mtd: rawnand: mtk: fix possible object reference leak
mtd: rawnand: jz4780: fix possible object reference leak
mtd: rawnand: atmel: fix possible object reference leak
mtd: rawnand: fsmc: Disable NAND on remove()
mtd: rawnand: fsmc: Reset NAND timings on resume()
mtd: spinand: Add support for GigaDevice GD5F1GQ4UExxG
mtd: rawnand: denali: remove unused dma_addr field from denali_nand_info
mtd: rawnand: denali: remove unused function argument 'raw'
mtd: rawnand: denali: remove unneeded denali_reset_irq() call
...
Commit 6f1fe97bec ("mtd: rawnand: denali_dt: add more clocks based
on IP datasheet") introduced a more correct binding that requires
three named clocks.
Now that all upstream DT files migrated over to it, remove the single
anonymous clock support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Dinh Nguyen <dinguyen@kernel.org>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: ae02ab00aa ("mtd: nand: jz4780: driver for NAND devices on JZ4780 SoCs")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Suggested-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft
reset may cause bus master lock up") for MX28 too. It has the same
problem.
Observed problem: once per 100,000+ MX28 reboots NAND read failed on
DMA timeout errors:
[ 1.770823] UBI: attaching mtd3 to ubi0
[ 2.768088] gpmi_nand: DMA timeout, last DMA :1
[ 3.958087] gpmi_nand: BCH timeout, last DMA :1
[ 4.156033] gpmi_nand: Error in ECC-based read: -110
[ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64
bytes from PEB 0:0, read only 0 bytes, retry
[ 4.171283] step 1 error
[ 4.173846] gpmi_nand: Chip: 0, Error -1
Without BCH soft reset we successfully executed 1,000,000 MX28 reboots.
I have a quote from NXP regarding this problem, from July 18th 2016:
"As the i.MX23 and i.MX28 are of the same generation, they share many
characteristics. Unfortunately, also the erratas may be shared.
In case of the documented erratas and the workarounds, you can also
apply the workaround solution of one device on the other one. This have
been reported, but I’m afraid that there are not an estimated date for
updating the Errata documents.
Please accept our apologies for any inconveniences this may cause."
Fixes: 6f2a6a5256 ("mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems")
Cc: stable@vger.kernel.org
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This disables the NAND on remove() and the errorpath,
making sure the chipselect gets deasserted when the
NAND is not in use.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When we go through a suspend/resume cycle the NAND
timings and other settings may have been lost so reset
the chip to bring it up in a known working state.
The FSMC only supports single CS chips so we only need
to call nand_reset(chip, 0).
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This is a leftover of commit 997cde2a22 ("mtd: nand: denali: skip
driver internal bounce buffer when possible").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This argument is not used at all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This code was added by commit 26d266e10e ("mtd: nand: denali: fix
raw and oob accessors for syndrome page layout"), but I do not see
sensible reason.
The IRQ flags are correctly reset by denali_cmd_ctrl(), so this code
is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_scan_ident() iterates over maxchips to find as many homogeneous
chips as possible.
Since commit 2d472aba15 ("mtd: nand: document the NAND
controller/NAND chip DT representation"), new drivers should pass in
the exact number of CS lines instead of possible max, but old
platforms may still rely on nand_scan_ident() to detect the actual
number of connected CS lines.
In that case, this loop bails out when manufacturer or device ID
unmatches. The reason of unmatch is most likely no chip is connected
to that CS line. If so, nand_reset() should already have failed,
and the following nand_readid_op() is pointless.
Before ->exec_op hook was introduced, drivers had no way to tell
the failure of NAND_CMD_RESET to the framework because the legacy
->cmdfunc() has void return type. Now drivers implementing ->exec_op
hook can return the error code. You can save nand_readid_op() by
checking the return value of nand_reset(). The return value of
nand_readid_op() should be checked as well. If it fails, probably
id[0] and id[1] are undefined values.
Just for consistency, it should be sensible to check the return
code in nand_do_write_oob() as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the last user of this hook, denali.c, stopped using it,
we can remove the erase hook from nand_legacy.
I squashed single_erase() because only the difference between
single_erase() and nand_erase_op() is the number of bit shifts.
The status/ret conversion in nand_erase_nand() is unneeded since
commit eb94555e9e ("mtd: nand: use usual return values for the
->erase() hook"). Cleaned it up now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit f9ebd1bb41 ("mtd: rawnand: Deprecate ->erase()") discouraged
the use of this hook, so I am happy to follow the suggestion.
Although the Denali IP provides a special MAP10 command for erasing,
using it would not buy us much. The Denali IP actually works with the
generic erasing by single_erase() + ->cmdfunc hook (nand_command_lp)
+ ->cmd_ctrl hook (denali_cmd_ctrl).
This method is also deprecated, but denali_erase() can go away
irrespective of ->exec_op conversion.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_base.c:5556:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5575:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5613:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_legacy.c:332:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_legacy.c:483:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add initial support for the Amlogic NAND flash controller which is
available on Meson SoCs.
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_get_device() was complex for apparently no good reason. Let's
replace this locking scheme with 2 mutexes: one attached to the
controller and another one attached to the chip.
Every time the core calls nand_get_device(), it will first lock the
chip and if the chip is not suspended, will then lock the controller.
nand_release_device() will release both lock in the reverse order.
nand_get_device() can sleep, just like the previous implementation,
which means you should never call that from an atomic context.
We also get rid of
- the chip->state field, since all it was used for was flagging the
chip as suspended. We replace it by a field called chip->suspended
and directly set it from nand_suspend/resume()
- the controller->wq and controller->active fields which are no longer
needed since the new controller->lock (now a mutex) guarantees that
all operations are serialized at the controller level
- panic_nand_get_device() which would anyway be a no-op. Talking about
panic write, I keep thinking the rawnand implementation is unsafe
because there's not negotiation with the controller to know when it's
actually done with it's previous operation. I don't intend to fix
that here, but that's probably something we should look at, or maybe
we should consider dropping the ->_panic_write() implementation
Last important change to mention: we now return -EBUSY when someone
tries to access a device that as been suspended, and propagate this
error to the upper layer.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We are about to simplify the locking in the rawnand framework, and part
of this simplication is about getting rid of chip->state, so let's
first patch drivers that check the state.
All of them do that to get a timeout value based on the operation that
is being executed. Since a timeout is, by definition, something that
is here to prevent hanging on an event that might never happen,
picking the maximum timeout value no matter the operation should be
harmless.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Stop initializing omap_gpmc_controller fields are declaration time and
replace that by a call to nand_controller_init(). Since the same object
might be shared by several NAND chips and the NAND controller driver
expects a ->probe() per-chip, we need to keep track of the
omap_gpmc_controller state (whether it's already been initialized or
not).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_controller->wq has never been meant to be used by NAND controller
drivers. This waitqueue is used by the framework to serialize accesses
to a NAND controller, and messing up with its state is a really bad
idea.
Declare a completion object in tmio_nand and use it to wait for RB
transitions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_controller_init() has been added to simplify nand_controller
struct initialization. Use this function instead of duplicating the
logic.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In non-EDO, tREA should be less than tRP to guarantee that the
controller does not sample the IO lines too early. Unfortunately, the
sunxi NAND controller does not allow us to have different values for
tRP and tREH (tRP = tREH = tRW / 2).
We have 2 options to overcome this limitation:
1/ Extend tRC to fulfil the tREA <= tRC / 2 constraint
2/ Use EDO mode (only works if timings->tRLOH > 0)
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The datasheet specifies the upper four bits are reserved.
Testing on real hardware shows that these bits can indeed be nonzero.
Signed-off-by: Emil Lenngren <emil.lenngren@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix the struct description and use standard kernel-doc header format
(even if the file is not parsed by the doc generator).
We also replace tabs by a single space.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
And get rif of all legacy hooks and unused fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the license text by an SPDX tag and fix MODULE_LICENSE() to
match GPL-2.0+.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace them by nand_chip pointers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_chip objects are sometimes called chip and sometimes nand. Rename
all of them into nand to make things consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use struct_size() to calculate sunxi_nand object size.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
sunxi_nand_chip objects are sometimes called chip and other times
called sunxi_nand. Make that consistent and name all occurrences
sunxi_nand.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch adds the polling mode, a basic mode that do not need
any DMA channels. This mode is also useful for debug purpose.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The driver adds the support for the STMicroelectronics FMC2 NAND
Controller found on STM32MP SOCs.
This patch is based on FMC2 command sequencer.
The purpose of the command sequencer is to facilitate the programming
and the reading of NAND flash pages with the ECC and to free the CPU
of sequencing tasks.
It requires one DMA channel for write and two DMA channels for read
operations.
Only NAND_ECC_HW mode is actually supported.
The driver supports a maximum 8k page size.
The following ECC strength and step size are currently supported:
- nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8)
- nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4)
- nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC
based on Hamming)
This patch has been tested on Micron MT29F8G08ABACAH4 and
MT29F8G16ABACAH4
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix kernel-doc warnings in drivers/mtd/nand/raw:
../drivers/mtd/nand/raw/nand_base.c:420: warning: Function parameter or member 'chip' not described in 'nand_fill_oob'
../drivers/mtd/nand/raw/nand_bbt.c:173: warning: Function parameter or member 'this' not described in 'read_bbt'
../drivers/mtd/nand/raw/nand_bbt.c:173: warning: Excess function parameter 'chip' description in 'read_bbt'
Fixes: 0813621ba8 ("mtd: rawnand: Stop passing mtd_info objects to internal functions")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: linux-mtd@lists.infradead.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
The manufacturer specific initialization has already been done when
block unlocking takes place, and if anything goes wrong during this
procedure we should call spinand_manufacturer_cleanup().
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Looks like PROGRAM LOAD (AKA write cache) does not necessarily reset
the cache content to 0xFF (depends on vendor implementation), so we
must fill the page cache entirely even if we only want to program the
data portion of the page, otherwise we might corrupt the BBM or user
data previously programmed in OOB area.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Reported-by: Stefan Roese <sr@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
The function jz_nand_ioremap_resource() needs a pointer to an __iomem
pointer as its last argument but this argument is declared as:
void * __iomem *base
Fix this by using the correct declaration:
void __iomem **base
which then also removes the following Sparse's warnings:
282:15: warning: incorrect type in assignment (different address spaces)
282:15: expected void *[noderef] <asn:2>
282:15: got void [noderef] <asn:2> *
322:57: warning: incorrect type in argument 4 (different address spaces)
322:57: expected void *[noderef] <asn:2> *base
322:57: got void [noderef] <asn:2> **
402:67: warning: incorrect type in argument 4 (different address spaces)
402:67: expected void *[noderef] <asn:2> *base
402:67: got void [noderef] <asn:2> **
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Hammering the "bank enable" (PBKEN) bit on and off between
every command crashes the Nomadik NHK15 with this message:
Scanning device for bad blocks
Unhandled fault: external abort on non-linefetch (0x008) at 0xcc95e000
pgd = (ptrval)
[cc95e000] *pgd=0b808811, *pte=40000653, *ppte=40000552
Internal error: : 8 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.20.0-rc2+ #72
Hardware name: Nomadik STn8815
PC is at fsmc_exec_op+0x194/0x204
(...)
After a discussion we (me and Boris Brezillon) start to suspect
that this bit does not immediately control the chip select line
at all, it rather enables access to the bank and the hardware
will drive the CS autonomously. If there is a NAND chip connected,
we should keep this enabled.
As fsmc_nand_setup() sets this bit, we can simply remove the
offending code.
Fixes: 550b9fc4e3 ("mtd: rawnand: fsmc: Stop implementing ->select_chip()")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This patch fixes a memory corruption that occurred in the
qcom-nandc driver since it was converted to nand_scan().
On boot, an affected device will panic from a NPE at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual address 0
| pgd = (ptrval)
| [00000000] *pgd=00000000
| Internal error: Oops: 80000005 [#1] SMP ARM
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| PC is at (null)
| LR is at nand_block_isbad+0x90/0xa4
| pc : [<00000000>] lr : [<c0592240>] psr: 80000013
| sp : cf839d40 ip : 00000000 fp : cfae9e20
| r10: cf815810 r9 : 00000000 r8 : 00000000
| r7 : 00000000 r6 : 00000000 r5 : 00000001 r4 : cf815810
| r3 : 00000000 r2 : cfae9810 r1 : ffffffff r0 : cf815810
| Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| [<c0592240>] (nand_block_isbad) from [<c0580a94>]
| [<c0580a94>] (allocate_partition) from [<c05811e4>]
| [<c05811e4>] (add_mtd_partitions) from [<c0581164>]
| [<c0581164>] (parse_mtd_partitions) from [<c057def4>]
| [<c057def4>] (mtd_device_parse_register) from [<c059d274>]
| [<c059d274>] (qcom_nandc_probe) from [<c0567f00>]
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4. This causes the
sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_block_bad() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch restores the old behavior by reallocating the shared bam
transaction alloc_bam_transaction() after the chip was identified,
but before mtd_device_parse_register() (which is an alias for
mtd_device_register() - see panic) gets called. This fixes the
corruption and the driver is working again.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f1 ("mtd: rawnand: qcom: convert driver to nand_scan()")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
-----BEGIN PGP SIGNATURE-----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=JXhP
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.21' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra, vf610):
* Stopping to pass mtd_info objects to internal functions
* Reorganizing code to avoid forward declarations
* Dropping useless test in nand_legacy_set_defaults()
* Moving nand_exec_op() to internal.h
* Adding nand_[de]select_target() helpers
* Passing the CS line to be selected in struct nand_operation
* Making ->select_chip() optional when ->exec_op() is implemented
* Deprecating the ->select_chip() hook
* Moving the ->exec_op() method to nand_controller_ops
* Moving ->setup_data_interface() to nand_controller_ops
* Deprecating the dummy_controller field
* Fixing JEDEC detection
* Providing a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flagging 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fixing the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Dropping .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Removing denali_reset_banks()
* Removing ->dev_ready() hook
* Including <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Adding an SPDX tag to replace the license text
* Making conversion from chip to fsmc consistent
* Fixing unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Preventing timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Converting to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Adding an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Removing the depreacated mt29f_spinand driver from staging.
- Adding support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
The opcodes used by the controller when doing batched page prog should
be written in NFC_REG_WCMD_SET not FC_REG_RCMD_SET. Luckily, the
default NFC_REG_WCMD_SET value matches the one we set in the driver
which explains why we didn't notice the problem.
Fixes: 614049a8d9 ("mtd: nand: sunxi: add support for DMA assisted operations")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
marvell_nfc_wait_op() waits for completion during 'timeout_ms'
milliseconds before throwing an error. While the logic is fine, the
value of 'timeout_ms' is given by the core and actually correspond to
the maximum time the NAND chip will take to complete the
operation. Assuming there is no overhead in the propagation of the
interrupt signal to the the NAND controller (through the Ready/Busy
line), this delay does not take into account the latency of the
operating system. For instance, for a page write, the delay given by
the core is rounded up to 1ms. Hence, when the machine is over loaded,
there is chances that this timeout will be reached.
There are two ways to solve this issue that are not incompatible:
1/ Enlarge the timeout value (if so, how much?).
2/ Check after the waiting method if we did not miss any interrupt
because of the OS latency (an interrupt is still pending). In this
case, we assume the operation exited successfully.
We choose the second approach that is a must in all cases, with the
possibility to also modify the timeout value to be, e.g. at least 1
second in all cases.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit e1e6255c31 ("mtd: rawnand: omap2: convert driver to
nand_scan()") moved part of the init code in the ->attach_chip hook
and at the same time changed the struct device object passed to
dma_request_chan() (&pdev->dev instead of pdev->dev.parent).
Fixes: e1e6255c31 ("mtd: rawnand: omap2: convert driver to nand_scan()")
Reported-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_jedec_detect() should return 1 when the PARAM page parsing
succeeds, otherwise the core considers JEDEC detection failed and falls
back to ID-based detection.
Fixes: 480139d922 ("mtd: rawnand: get rid of the JEDEC parameter page in nand_chip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings. Fix them up.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We try to force NAND controller drivers to properly separate the NAND
controller object from the NAND chip one, so let's deprecate the dummy
controller object embedded in nand_chip to encourage them to create
their own instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the license text by an SPDX tag.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The dummy controller is kept around to support old drivers. Let's
patch this one and declare our own nand_controller instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mimic what has been done in the core and avoid passing mtd_info object
internally.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
checkpatch reports a bunch of coding style issues. Let's fix them
all in one step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add an SPDX GPL-2.0 tag and update MODULE_LICENSE() to match the
license text.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The dummy controller is kept around to support old drivers. Let's
patch this one and declare our own nand_controller instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_to_fsmc() is used almost everywhere except in
fsmc_setup_data_interface() where nand_get_controller_data() is used
instead. Make that consistent and drop the nand_set_controller_data()
call in the probe path.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The kernel-doc describing struct fsmc_nand_data is not in sync with
the struct itself. Add missing entries and drop invalid ones.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mimic what has been done in the core and stop passing mtd_info
objects to internal functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In nand_scan_ident(), the controller driver resets every NAND chip.
This is done by sending NAND_CMD_RESET. The Denali IP provides
another way to do the equivalent thing; if a bit is set in the
DEVICE_RESET register, the controller sends the RESET command to
the corresponding device. denali_reset_banks() uses it to reset
all devices beforehand.
This redundant reset sequence was needed to know the actual number
of chips before calling nand_scan_ident(); if DEVICE_RESET fails,
there is no chip in that chip select. Then, denali_reset_banks()
sets denali->max_banks to the number of detected chips.
As commit f486287d23 ("mtd: nand: denali: fix bank reset function
to detect the number of chips") explained, nand_scan_ident() issued
Set Features (0xEF) command to all CS lines, some of which may not be
connected with a chip. Then, the driver would wait for R/B# response,
which never happens.
This problem was solved by commit 107b7d6a7a ("mtd: rawnand: avoid
setting again the timings to mode 0 after a reset"). In the current
code, nand_setup_data_interface() is called from nand_scan_tail(),
which is invoked after the chip detection.
Now, we can really remove the redundant denali_nand_banks() by simply
passing the maximum number of chip selects supported by this IP
(typically 4 or 8) to nand_scan(). Let's leave all the chip detection
process to nand_scan_ident().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Denali NAND IP has no way to read out the current signal level
of the R/B# pin. Instead, denali_dev_ready() checks if the R/B#
transition has already happened. (The INTR__INT_ACT interrupt is
asserted at the rising edge of the R/B# pin.) It is not a correct
way to implement the ->dev_ready() hook.
In fact, it has a drawback; in the nand_scan_ident phase, the chip
detection iterates over maxchips until it fails to find a homogeneous
chip. For the last loop, nand_reset() fails if no chip is there.
If ->dev_ready hook exists, nand_command(_lp) calls nand_wait_ready()
after NAND_CMD_RESET. However, we know denali_dev_ready() never
returns 1 unless there exists a chip that toggles R/B# in that chip
select. Then, nand_wait_ready() just ends up with wasting 400 msec,
in the end, shows the "timeout while waiting for chip to become ready"
warning.
Let's remove the mis-implemented dev_ready hook, and fallback to
sending the NAND_CMD_STATUS and nand_wait_status_ready(), which
bails out more quickly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Don't readw()/writew() data directly from/to GPIO port which is under
control of gpio-omap driver, use GPIO consumer API instead.
The driver should now work with any 8-bit bidirectional GPIO port, not
only OMAP.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Data port used by the driver is actually an OMAP MPUIO device, already
under control of gpio-omap driver. For that reason we used to not
request the memory region of the port as that would fail because the
region is already busy. Despite that, we are still accessing the port
by just ioremapping it and performing read/write operations. Moreover,
we are doing that without any proteciton from other users legally
manipulating the port pins over GPIO API.
The plan is to convert the driver to access the port over GPIO consumer
API. Before that happens, already prevent from other users accessing
the port pins by requesting an array of its GPIO descriptors.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->setup_data_interface() is a controller specific method and should
thus be placed in nand_controller_ops.
In order to make that work with controllers that support keeping
pre-configured timings we need to add a new NAND_KEEP_TIMINGS flag to
inform the core it should skip the timings selection step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->exec_op() is a controller method and has nothing to do in the
nand_chip struct. Let's move it to the nand_controller_ops struct and
adjust the core and drivers accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to be selected is passed to ->exec_op() and
stored in chip->cur_cs and after patching all drivers implementing
->exec_op() to stop implementing this method, we can deprecate it by
moving it to the nand_legacy structure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is passed in nand_operation->cs, we can
get rid of the ->select_chip() implementation and replace it by an
internal function which is called from the chip->exec_op() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to assert is directly passed through the
nand_operation struct we can replace the fsmc_select_chip()
implementation by an internal fsmc_ce_ctrl() function which is
directly called from fsmc_exec_op()
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected on a nand_operation is passed in
nand_operation->cs we can make the ->select_chip() hook optional for
drivers implementing ->exec_op().
When not implemented, the core is assuming the CS line is automatically
asserted/deasserted by the driver ->exec_op() implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to deprecate the ->select_chip hook we need to pass the CS
line a NAND operations are targeting. This is done through the
addition of a cs field to the nand_operation struct.
We also need to keep track of the currently selected target to
properly initialize op->cs, hence the ->cur_cs field addition to the
nand_chip struct.
Note that op->cs is not assigned in nand_exec_op() because we might
rework the way we execute NAND operations in the future (adopt a
queuing mechanism instead of the serialization we have right now).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a wrapper to prevent drivers and core code from directly calling
the ->select_chip hook which we are about to deprecate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All NAND objects are supposed to inherit from nand_controller. The
framework is providing a dummy controller object, but we're moving
away from this approach in favor of explicit inheritance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd_device_register() can fail, and when it does we should propagate
the error and cleanup what has been done before.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Remove unused labels, rename out_mtd into err_unmap to make it clearer
and return 0 instead of using a goto out at the end of the registration
procedure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Most of them were reported by checkpatch:
* s/u_char/u8/
* remove unneeded blank lines
* don't print warning messages when devm_kzalloc() fails
* Use ! instead of == NULL
* Remove invalid comment
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add an SPDX GPL-2.0 tag and update MODULE_LICENSE() to match the
license text.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Drop the asm and mach headers inclusion and allow this driver to be
compiled when COMPILE_TEST=y in order to increase compile-test
coverage.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_exec_op() is only used by core code (nand_xxx.c files). Let's
move this inline function in drivers/mtd/nand/raw/internals.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_legacy_set_defaults() returns directly if chip->exec_op != NULL,
no need to test !chip->exec_op after that.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Avoid forward declaration of nand_get_device(), nand_do_write_oob()
and nand_update_bbt() by moving functions around.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
After having reworked the rawnand API to avoid passing mtd_info
objects around, let's do the same for internal functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
DEFINE_SHOW_ATTRIBUTE macro can help us simplify the code, so change
to it. And change the DEBUGFS_RO_ATTR macro defined in some file to a
standard macro.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Fix the size of the buffer allocated to store the in-memory BBT.
This bug was previously hidden by a different bug, that was fixed in
commit d098093ba0 ("mtd: nand: Fix nanddev_neraseblocks()").
Fixes: 9c3736a3de ("mtd: nand: Add core infrastructure to deal with NAND devices")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
PAGE_READ is used by RISC-V arch code included through mm headers,
and it makes sense to bring in a prefix on these in the driver.
drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
#define PAGE_READ 0x2
In file included from include/linux/memremap.h:7,
from include/linux/mm.h:27,
from include/linux/scatterlist.h:8,
from include/linux/dma-mapping.h:11,
from drivers/mtd/nand/raw/qcom_nandc.c:17:
arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
Caught by riscv allmodconfig.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Use the new of_get_compatible_child() helper to lookup the nfc child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix a related nfc-node reference leak.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: stable <stable@vger.kernel.org> # 4.11
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Josh Wu <rainyfeeling@outlook.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make sure we flag all 1.8V broken chips as not supporting this feature.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the generic DMA API instead of the legacy PCI DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK macros.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace legacy callbacks with ->select_chip() and ->exec_op().
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace use of legacy .IOADDR_R/W with runtime calculations based on
priv->io_base.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each controller driver having access to NAND R/B pin over GPIO would
have to reimplement the polling loop otherwise.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Check return value of nand_read_data_op.
Notice that, currently, all instances of nand_read_data_op() are
being checked, with the exception of two of them in marvell_nand
driver, in which the caller function explicitly returns 0 every
time.
Also, notice that I moved the declaration of *ret* to the top of
fsmc_read_page_hwecc().
Addresses-Coverity-ID: 1471968 ("Unchecked return value")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
W25N01GV is a single die version of the already supported
W25M02GV with half the capacity. Everything else is the
same so introduce support for W25N01GV.
Datasheet:http://www.winbond.com/resource-files/w25n01gv%20revl%20050918%20unsecured.pdf
Tested on 8devices Jalapeno dev board under OpenWrt running 4.19-rc5.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Remove kernel-doc notation for a deleted function parameter to prevent
a kernel-doc warning:
../drivers/mtd/nand/raw/nand_base.c:603: warning: Excess function parameter 'mtd' description in 'panic_nand_wait'
Fixes: f1d46942e8 ("mtd: rawnand: Pass a nand_chip object to chip->waitfunc()")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Core changes:
* Support non-uniform erase size
* Support controllers with limited TX fifo size
Driver changes:
* m25p80: Re-issue a WREN command after each write access
* cadence: Pass a proper dir value to dma_[un]map_single()
* fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
* intel-spi: Add a new PCI entry for Ice Lake
NAND changes:
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
MTD changes:
* physmap cleanups/fixe
* gpio-addr-flash cleanups/fixes
-----BEGIN PGP SIGNATURE-----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=7w4w
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd
Pull mtd updates from Boris Brezillon:
"SPI NOR core changes:
- Support non-uniform erase size
- Support controllers with limited TX fifo size
Driver changes:
- m25p80: Re-issue a WREN command after each write access
- cadence: Pass a proper dir value to dma_[un]map_single()
- fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
- intel-spi: Add a new PCI entry for Ice Lake
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID
byte.
MTD changes:
- physmap cleanups/fixe
- gpio-addr-flash cleanups/fixes"
* tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd: (93 commits)
jffs2: free jffs2_sb_info through jffs2_kill_sb()
mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash
mtd: maps: gpio-addr-flash: Convert to gpiod
mtd: maps: gpio-addr-flash: Replace array with an integer
mtd: maps: gpio-addr-flash: Use order instead of size
mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
mtd: devices: m25p80: Make sure WRITE_EN is issued before each write
mtd: spi-nor: Support controllers with limited TX FIFO size
mtd: spi-nor: cadence-quadspi: Use proper enum for dma_[un]map_single
mtd: spi-nor: parse SFDP Sector Map Parameter Table
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: rawnand: marvell: fix the IRQ handler complete() condition
mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset
mtd: rawnand: r852: fix spelling mistake "card_registred" -> "card_registered"
mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper
mtd: maps: gpio-addr-flash: Use devm_* functions
mtd: maps: gpio-addr-flash: Fix ioremapped size
mtd: maps: gpio-addr-flash: Replace custom printk
mtd: physmap_of: Release resources on error
...
With the current implementation, the complete() in the IRQ handler is
supposed to be called only if the register status has one or the other
RDY bit set. Other events might trigger an interrupt as well if
enabled, but should not end-up with a complete() call.
For this purpose, the code was checking if the other bits were set, in
this case complete() was not called. This is wrong as two events might
happen in a very tight time-frame and if the NDSR status read reports
two bits set (eg. RDY(0) and RDDREQ) at the same time, complete() was
not called.
This logic would lead to timeouts in marvell_nfc_wait_op() and has
been observed on PXA boards (NFCv1) in the Hamming write path.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Reported-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Daniel Mack <daniel@zonque.org>
NAND devices need additional data area (OOB) for error correction,
but it is also used for Bad Block Marker (BBM). In many cases, the
first byte in OOB is used for BBM, but the location actually depends
on chip vendors. The NAND controller should preserve the precious
BBM to keep track of bad blocks.
In Denali IP, the SPARE_AREA_SKIP_BYTES register is used to specify
the number of bytes to skip from the start of OOB. The ECC engine
will automatically skip the specified number of bytes when it gets
access to OOB area.
The same value for SPARE_AREA_SKIP_BYTES should be used between
firmware and the operating system if you intend to use the NAND
device across the control hand-off.
In fact, the current denali.c code expects firmware to have already
set the SPARE_AREA_SKIP_BYTES register, then reads the value out.
If no firmware (or bootloader) has initialized the controller, the
register value is zero, which is the default after power-on-reset.
In other words, the Linux driver cannot initialize the controller
by itself.
Some possible solutions are:
[1] Add a DT property to specify the skipped bytes in OOB
[2] Associate the preferred value with compatible
[3] Hard-code the default value in the driver
My first attempt was [1], but in the review process, [3] was suggested
as a counter-implementation.
(https://lore.kernel.org/patchwork/patch/983055/)
The default value 8 was chosen to match to the boot ROM of the UniPhier
platform. The preferred value may vary by platform. If so, please
trade up to a different solution.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Trivial fix to spelling mistake struct field name, rename it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that most of the raw NAND API is consistent and has almost all its
helpers and hooks using a single nand_chip object instead of an mtd_info
one (or both), let's do the same cleanup in the raw NAND vendors
drivers.
Apply this change to the Toshiba driver so that the internal helper to
retrieve the ECC status does only take a nand_chip object.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently, the selection of ECC byte ordering for software hamming is
done at compilation time, which doesn't make sense when ECC byte
calculation is done in hardware and byte ordering is forced by the
hardware engine.
In this case, only the correction is done in software and we want to
force the byte-ordering no matter the value of CONFIG_MTD_NAND_ECC_SMC.
This is typically the case for the FSMC (Smart Media ordering), TMIO and
TXX9NDFMC (regular byte ordering) blocks.
For all other use cases (pure software implementation, SM FTL and
nandecctest), we keep selecting the byte ordering based on the
CONFIG_MTD_NAND_ECC_SMC value. It might not be ideal for SM FTL (I'd
expect Smart Media ordering to be employed by the Smart Media FTL), but
this option doesn't seem to be enabled in the existing _defconfig, so
I can't tell setting sm_order to true is the right choice.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Clang warns when one enumerated type is converted implicitly to another:
drivers/mtd/nand/raw/sh_flctl.c:483:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_DEV_TO_MEM) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
drivers/mtd/nand/raw/sh_flctl.c:542:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_MEM_TO_DEV) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_data_direction to satisfy Clang.
DMA_MEM_TO_DEV = DMA_TO_DEVICE = 1
DMA_DEV_TO_MEM = DMA_FROM_DEVICE = 2
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In its current shape, the driver sets data port direction before each
byte read/write operation, even during multi-byte transfers. Improve
performance of the driver by setting the port direction only when
needed.
This optimisation will become particularly important as soon as
planned conversion of the driver to GPIO API for data I/O will be
implemented.
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Introduce a driver private structure and allocate it on device probe.
Use it for storing nand_chip structure, GPIO descriptors prevoiusly
stored in static variables as well as io_base pointer previously passed
as nand controller data or platform driver data. Subsequent patches
may populate the structure with more members as needed.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now as Amstrad Delta board - the only user of this driver - provides
GPIO lookup tables, switch from GPIO numbers to GPIO descriptors and
use the table to locate required GPIO pins.
Declare static variables for storing GPIO descriptors and replace
gpio_ function calls with their gpiod_ equivalents.
Pin naming used by the driver should be followed while respective GPIO
lookup table is initialized by a board init code.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a potential execution path in which function
of_find_compatible_node() returns NULL. In such a case,
we end up having a NULL pointer dereference when accessing
pointer *nfc_np* in function of_clk_get().
So, we better don't take any chances and fix this by null
checking pointer *nfc_np* before calling of_clk_get().
Addresses-Coverity-ID: 1473052 ("Dereference null return value")
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for two new layouts: 8kiB pages NAND chips, requesting
either 4 or 8 bit of correctability per 512B step.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch enables support to read the ECC level from the NAND flash
using ESMT SLC NAND ID byte 5 information as documented e.g. in the
following data sheet:
https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F59L1G81LA(2Y).pdf
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This moves JEDEC related code to nand_jedec.c and JEDEC related
struct/macros to include/linux/mtd/jedec.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This moves ONFI related code to nand_onfi.c and ONFI related
struct/macros to include/linux/mtd/onfi.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Allows us to move a few hundred lines of deprecated code out of the
core file which is quite big.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A lot of things defined in rawnand.h should not be exposed to NAND
controller drivers and should only be shared by core files.
Create the drivers/mtd/nand/raw/internals.h header to store such
definitions, and move all private defs to this header.
Also remove EXPORT_SYMBOLS() on functions that are not supposed to be
exposed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
onfi_get_async_timing_mode() is only used in one place inside
nand_base.c. Let's inline the code and kill the helper.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_nand_xxx definitions are just used by the plat_nand driver.
Let's move those definitions out of the core/driver-agnostic rawnand.h
header.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those definitions are not used, let's remove them.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The wait timeouts and delays are directly extracted from the NAND
timings and ->chip_delay is only used in legacy path, so let's move it
to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks should be replaced by a proper ->exec_op() implementation.
Move them to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ->erase() hook have been overloaded by some drivers for bad reasons:
either the driver was not fitting in the NAND framework and should have
been an MTD driver (docg4), or the driver uses a specific path for the
ERASE operation (denali), instead of implementing it generically.
In any case, we should discourage people from overloading this method
and encourage them to implement ->exec_op() instead.
Move the ->erase() hook to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been overloaded by some drivers for bad reasons:
either the driver was not fitting in the NAND framework and should
have been an MTD driver (docg4), or it was not properly implementing
the OOB read/write request or had a weird layout where BBM are trashed.
In any case, we should discourage people from overloading those
methods and encourage them to fix their driver instead.
Move the ->block_{bad,markbad}() hooks to the nand_legacy struct to
make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We regularly have new NAND controller drivers that are making use of
fields/hooks that we want to get rid of but can't because of all the
legacy drivers that we might break if we do.
So, instead of removing those fields/hooks, let's move them to a
sub-struct which is clearly documented as deprecated.
We start with the ->IO_ADDR_{R,W] fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There's no point in poisoning the ->IO_ADDR_{R,W}, a NULL pointer
is just as good to detect unexpected ->IO_ADDR_{R,W} usage.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The only reason we were skipping nand_scan_ident() when maxchips == 0
was to make the docg4 to work. Now that this driver is gone we can
remove this special case and return an error when maxchips is 0.
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There's no good reason to make maxchips a signed integer, since only
positive values are valid. Make it an unsigned int.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The diskonchip G4 driver does not fit very well in the raw/parallel
NAND framework simply because such chips have an internal controller
translating DoC-specific commands into NAND ones.
Keeping such a driver in the raw NAND framework is a real burden for
NAND maintainers.
Not to mention that some parts of this driver are a bit worrisome:
- writes are done by subpages, even though we're interfacing with an MLC
chip which are known to not support subpage writes very well (it might
be that the FTL handles the complexity for us though)
- some part of the code are simply ignoring return codes of function that
can fail in a few occasions
- there's a hack to support OOB writes when no data is provided. This
operation is not supported by the chip and should have been rejected,
and nandwrite and other userspace tools should have been patched to
deal with such devices
- the driver is apparently broken when ignore_badblocks module param
is not set to 1 and nobody noticed that (don't know since when this
is the case, but it's not a recent change)
http://lists.infradead.org/pipermail/linux-mtd/2018-July/082472.html
Add to that the fact that we already have a docg3 driver in
drivers/mtd/devices/docg3.c and, looking at the code (and regs), it
seems docg3 and docg4 have a lot in common (even the author of this
driver seemed to have realized that interfacing with the raw NAND
framework might have been a bad idea
http://lists.infradead.org/pipermail/linux-mtd/2012-January/039517.html).
For all these reasons, I'm proposing to remove this driver. If anyone
ever wants to add support for this chip back, I'd suggest extending
the docg3 driver instead of adding a completely new driver.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sergey Larin <cerg2010cerg2010@mail.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for the layout used by 2kiB page NAND chips requesting at
least 8-bit of correction per 512 bytes. This layout requires a bit of
handling as:
1/ It can only fit if the NAND chip has at least 128 OOB bytes.
2/ The Bad Block Markers are located in the middle of the data bytes
and shall not be used.
3/ It has been experimentally observed that, for certain layouts, the ECC
engine tries to correct data while it should not because the errors
are uncorrectable. While this is harmless for truly bad pages, it
creates bitflips in empty pages. To avoid such scenario that
augments artificially the number of bitflips we re-read in raw mode
the entire page instead of just the ECC bytes. This is done only
for this layout to avoid an unneeded penalty with other setups.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
We are about to support a new layout that triggers a faulty mechanism in
BCH engine that creates bitflips in erased pages.
Before adding the quirk that will workaround this issue, this patch just
reworks a bit the section that handles ECC failures in BCH read path.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the nand_erase_nand() helper.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the nand_xxx_bbt() helpers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->setup_data_interface() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->setup_read_retry() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->{get,set}_features() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->erase() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->waitfunc() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmdfunc() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->dev_ready() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmd_ctrl() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->block_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->select_chip() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->correct()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->calculate()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->hwctl()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to
take a nand_chip object instead of an mtd_info one.
Now is nand_wait_ready()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to
take a nand_chip object instead of an mtd_info one.
Now is nand_release()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to take
a nand_chip object instead of an mtd_info one.
We start with nand_scan().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
In order to do that, we first need to update the platform_nand_ctrl
hooks to take a nand_chip object instead of an mtd_info.
We add temporary plat_nand_xxx() wrappers to the do the mtd -> chip
conversion, but those will be dropped when patching nand_chip hooks to
take a nand_chip object.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
I thought the read-back of the DMA_ENABLE register was unnecessary
(at least it is working on my boards), then deleted it in commit
586a2c5290 ("mtd: nand: denali: squash denali_enable_dma() helper
into caller"). Sorry, I was wrong - it caused a timing issue on
Cyclone5 SoCFPGAs.
Revive the register read-back, commenting why this is necessary.
Fixes: 586a2c5290 ("mtd: nand: denali: squash denali_enable_dma() helper into caller")
Cc: <stable@vger.kernel.org>
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Since the addition of WARN_ON() in nand_subop_get_data/addr_len()
helpers, this driver will produce harmless warnings (mostly at probe)
just because it always calls the nand_subop_get_data_len() helper in
the parsing function (even on non-data instructions, where this value
is meaningless and unneeded).
Fix these warnings by deriving the length only when it is relevant.
Fixes: 760c435e0f ("mtd: rawnand: make subop helpers return unsigned values")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A recent commit removed the incorrect use of phys_to_dma from this
driver, but failed to remove the dma-direct.h include, so do that
now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use SPDX-License-Identifier instead of the license boilerplates.
This conversion makes it easier for us to scan the license, then
I notice license mismatch problems.
The license blocks in denali* indicate GPL-2.0 "only", while the
MODULE_LICENSE in denali.c and denali_dt.c is GPL-2.0 "or later"
as explained in include/linux/module.h as follows:
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
I fixed the MODULE_LICENSE tags, assuming the license blocks are
the authors' intention.
Also, add missing MODULE_DESCRIPTION/AUTHOR to denali.c
While I am touching the license things, I added my credit to denali.c
because this driver was largely re-written by me in 2017.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Newer versions of the IFC controller use a different method of initializing the
internal SRAM: Instead of reading from flash, a bit in the NAND configuration
register has to be set in order to trigger the self-initializing process.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The SRAM initialization might fail. If that happens further NAND operations
won't be successful. Therefore, the chip init routine should fail if the SRAM
initialization didn't work.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A stale document about the old pxa3cc_nand.c driver is available in
Documentation/mtd/nand/. Rewrite the parts that explain the IP itself
and some non-trivial choices made in the driver directly in
marvell_nand.c to then be able to remove this file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch is a patch to support TOSHIBA MEMORY CORPORATION BENAND
memory devices. Check the status of the built-in ECC with the Read
Status command without using the vendor specific command. The Read
Status command only knows whether there was bitflips above the
threshold and can not get accurate bitflips. For now, I set
max_bitflips mtd->bitflip_threshold.
Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The marvell_nfc_init() function fiddles with some bits of a system
controller on Armada 7K/8K. However, it does a read/modify/write
sequence on GENCONF_CLK_GATING_CTRL and GENCONF_ND_CLK_CTRL, which
isn't safe from a concurrency point of view, as the regmap lock isn't
taken accross the read/modify/write sequence. To solve this issue, use
regmap_update_bits().
While at it, since the "reg" variable is no longer needed for the
read/modify/write sequences, get rid of it for the regmap_write() to
GENCONF_SOC_DEVICE_MUX, and directly pass the value to be written as
argument.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit c120e75e0e ("mtd: nand: use read_oob() instead of cmdfunc()
for bad block check") removed this only user of the ->read_word()
method but kept the hook in place. Remove it now.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to make sure we use ->exec_op() to wait for chip readiness
when it's available we provide an helper that does the selection
between ->exec_op(), udelay(chip->chip_delay) and nand_wait_ready()
based on what's implemented by the controller driver.
We then use it in nand_wait_readrdy().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The logic to wait for chip readiness after a page read has been
duplicated in nand_do_read_ops() and nand_do_read_oob(). Provide an
helper that does the right thing and call it where appropriate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 49aa76b166 ("mtd: rawnand: do not execute nand_scan_ident()
if maxchips is zero") gave a new meaning for calling nand_scan_ident()
with maxchips=0.
It is a special usage for some drivers such as docg4, but actually
the Denali driver may pass maxchips=0 to nand_scan() when the driver
is enabled but no NAND chip is found on the board for some reasons.
If nand_scan_with_ids() is called with maxchips=0, nand_scan_ident()
is skipped, then nand_set_defaults() is skipped as well. Thus, the
driver must set chip->controller beforehand. Otherwise, nand_attach()
causes NULL pointer dereference.
In fact, the Denali controller knows the number of connected chips
before calling nand_scan_ident(); if DEVICE_RESET fails, there is no
chip in that chip select. Then, denali_reset_banks() sets the maxchips
to the number of detected chips. If no chip is found, maxchips is zero.
In this case, there is no point for calling nand_scan() because we know
it will fail for sure. Let's make the probe function fail immediately.
Fixes: 49aa76b166 ("mtd: rawnand: do not execute nand_scan_ident() if maxchips is zero")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If gcc (e.g. 4.1.2) decides not to inline init_mtd_structs() and
read_id_reg(), this will cause section mismatches, and crashes:
WARNING: drivers/mtd/nand/raw/docg4.o(.text+0xc10): Section mismatch in reference from the function docg4_attach_chip() to the function .init.text:init_mtd_structs()
The function docg4_attach_chip() references
the function __init init_mtd_structs().
This is often because docg4_attach_chip lacks a __init
annotation or the annotation of init_mtd_structs is wrong.
WARNING: drivers/mtd/nand/raw/docg4.o(.text+0xc3e): Section mismatch in reference from the function docg4_attach_chip() to the function .init.text:read_id_reg()
The function docg4_attach_chip() references
the function __init read_id_reg().
This is often because docg4_attach_chip lacks a __init
annotation or the annotation of read_id_reg is wrong.
Fix this by dropping the now incorrect __init annotations from
init_mtd_structs() and read_id_reg().
Fixes: 66a38478dc ("mtd: rawnand: docg4: convert driver to nand_scan()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer;
also offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types
-----BEGIN PGP SIGNATURE-----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=eTIC
-----END PGP SIGNATURE-----
Merge tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer; also
offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types"
* tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (529 commits)
ASoC: adav80x: mark expected switch fall-through
ASoC: da7219: Add delays to capture path to remove DC offset noise
ALSA: usb-audio: Mark expected switch fall-through
ALSA: mixart: Mark expected switch fall-through
ALSA: opl3: Mark expected switch fall-through
ALSA: hda/ca0132 - Add exit commands for Recon3D
ALSA: hda/ca0132 - Change mixer controls for Recon3D
ALSA: hda/ca0132 - Add Recon3D input and output select commands
ALSA: hda/ca0132 - Add DSP setup defaults for Recon3D
ALSA: hda/ca0132 - Add Recon3D startup functions and setup
ALSA: hda/ca0132 - Add bool variable to enable/disable pci region2 mmio
ALSA: hda/ca0132 - Add Recon3D pincfg
ALSA: hda/ca0132 - Add quirk ID and enum for Recon3D
ALSA: hda/ca0132 - Add alt_functions unsolicited response
ALSA: hda/ca0132 - Clean up ca0132_init function.
ALSA: hda/ca0132 - Create mmio gpio function to make code clearer
ASoC: wm_adsp: Make DSP name configurable by codec driver
ASoC: wm_adsp: Declare firmware controls from codec driver
ASoC: max98373: Added software reset register to readable registers
ASoC: wm_adsp: Correct DSP pointer for preloader control
...
The driver uses genalloc functions. Select GENERIC_ALLOCATOR to prevent
build errors when selected through COMPILE_TEST.
Fixes: 88a40e7dca ("mtd: rawnand: atmel: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Now that it is possible to do dynamic allocations during the
identification phase, convert the onfi_params structure (which is only
needed with ONFI compliant chips) into a pointer that will be allocated
only if needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Thanks to the migration of all drivers to use nand_scan() and the
related nand_controller_ops, we can now allocate data during the
detection phase. Let's do it first for the NAND model parameter which
is allocated in nand_detect().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Both nand_scan_ident() and nand_scan_tail() helpers used to be called
directly from controller drivers that needed to tweak some ECC-related
parameters before nand_scan_tail(). This separation prevented dynamic
allocations during the phase of NAND identification, which was
inconvenient.
All controller drivers have been moved to use nand_scan(), in
conjunction with the chip->ecc.[attach|detach]_chip() hooks that
actually do the required tweaking sequence between both ident/tail
calls, allowing programmers to use dynamic allocation as they need all
across the scanning sequence.
Declare nand_scan_[ident|tail]() statically now.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
A comment in the probe declares that values are assigned to ecc.size
and ecc.bytes, but these values will be overwritten. This is not
entirely right as they are overwritten only if
mtd->writesize >= 512. Let's clarify this by moving these assignations
to txx9ndfmc_nand_scan().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare the migration to nand_scan() by moving both calls to
nand_scan_ident() and nand_scan_tail() in a single spot.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup(), not a
nand_release() as mtd_device_register() (or one of its variants) has not
been called and there is no need to deregister any MTD device yet.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some driver (eg. docg4) will need to handle themselves the
identification phase. As part of the migration to use nand_scan()
everywhere (which will unconditionnaly call nand_scan_ident()), we add
a condition at the start of nand_scan_with_ids() to jump over
nand_scan_ident() if the maxchips parameters is zero, meaning that the
driver does not want the core to handle this phase.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
No need for an atmel_nand_register() function, let's move the code in
it directly where the function was called: in
atmel_nand_controller_add_nand(). To make things consistent, also
rename atmel_nand_unregister() into
atmel_nand_controller_remove_nand().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan_with_ids() (alternative to nand_scan() for passing
a flash IDs table) instead of the nand_scan_ident() + nand_scan_tail()
pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
nand_cleanup() should be called upon error after a successful
nand_scan_tail().
Rework the error path to follow this rule .
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
As already done in the core, calling a struct nand_controller
'hw_control' is misleading. Use the same name as in nand_base.c:
'controller'.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Xiaolei Li <xiaolei.li@mediatek.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Harvey Hunt <harveyhuntnexus@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Notes:
"pw 947037"
Return -ENOTSUPP instead of -1 from ->chip_init_tail() before migrating
this driver to use nand_scan() and transform this function to be a
callback run by the core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Also change the unused "struct device *dev" parameter of the driver
structure into a platform device to reuse it in the ->attach_chip()
hook.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
We don't use the GPIO API in this driver, let's just remove the
<linux/gpio.h> inclusion.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gpio/consumer.h defines everything we need, and it's clearly stated in
gpio.h that GPIO consumers should directly stop including gpio.h if they
can.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit ddd5ed3a90 ("mtd: rawnand: sunxi: Remove support for
GPIO-based Ready/Busy polling") removed GPIO-based RB polling. We no
longer need to include gpio headers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
GPIO consumers should no longer include <linux/gpio.h>, and instead
include <linux/gpio/consumer.h>.
Also, explicitly include <include/io.h> since it seems to be missing
after switching to <linux/gpio/consumer.h>.
This fixes a build error when selecting the driver without selecting
GPIOLIB, which can happen when COMPILE_TEST=y.
Fixes: 6968e07e81 ("mtd: rawnand: jz4740: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to remove the limitation that forbids dynamic allocation in
nand_scan_ident(), we must create a path that will be the same for all
controller drivers. The idea is to use nand_scan() instead of the widely
used nand_scan_ident()/nand_scan_tail() couple. In order to achieve
this, controller drivers will need to adjust some parameters between
these two functions depending on the NAND chip wired on them.
This takes the form of two new hooks (->{attach,detach}_chip()) that are
placed in a new nand_controller_ops structure, which is then attached
to the nand_controller object at driver initialization time.
->attach_chip() is called between nand_scan_ident() and
nand_scan_tail(), and ->detach_chip() is called in the error path of
nand_scan() and in nand_cleanup().
Note that some NAND controller drivers don't have a dedicated
nand_controller object and instead rely on the default/dummy one
embedded in nand_chip. If you're in this case and still want to
initialize the controller ops, you'll have to manipulate
chip->dummy_controller directly.
Last but not least, it's worth mentioning that we plan to move some of
the controller related hooks placed in nand_chip into
nand_controller_ops to make the separation between NAND chip and NAND
controller methods clearer.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
In the raw NAND core, a NAND chip is described by a nand_chip structure,
while a NAND controller is described with a nand_hw_control structure
which is not very meaningful.
Rename this structure nand_controller.
As the structure gets renamed, it is logical to also rename the core
function initializing it from nand_hw_control_init() to
nand_controller_init().
Lastly, the 'hwcontrol' entry of the nand_chip structure is not
meaningful neither while it has the role of fallback when no controller
structure is provided by the driver (the controller driver is dumb and
can only control a single chip). Thus, it is renamed dummy_controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit 260e89a6e0 ("mtd: core: tone down suggestion that dev.parent
should be set") removed the only user of caller_is_module() but forgot
to remove the definition itself. Let's remove it now.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All of the code in the probe path assumes ->sets != NULL and
->nrsets > 0. Error out if that's not the case to avoid dereferencing a
NULL pointer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A report from Colin Ian King pointed a CoverityScan issue where error
values on these helpers where not checked in the drivers. These
helpers can error out only in case of a software bug in driver code,
not because of a runtime/hardware error. Hence, let's WARN_ON() in this
case and return 0 which is harmless anyway.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make sure __LINUX_ARM_ARCH__ is defined before testing its value.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Include linux/sizes.h instead of asm/sizes.h to make code completely
arch independent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We currently don't store the on-die ECC state (enabled/disabled) which
might force us to re-disable the engine even if it's already been
disabled after we've read the page in raw mode to count the actual
number of bitflips.
Add an "enabled" field to struct micron_on_die_ecc to keep track of the
ECC state.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some chips have their on-die ECC forcibly enabled, there's no point in
trying to enable/disable the ECC engine in that case.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The MT29F2Gxxx chips with 4bits/512byte on-die ECC let us know when
some bitflips were corrected by the on-die ECC, but they do not report
the actual number of bitflips that were present in the data+ECC chunk.
We initially decided to always return ecc->strength to avoid re-reading
the page in raw mode + comparing it to the corrected buffer to extract
the real number of bitflips, but this forces UBI to move data around as
soon as one bitflip is present in a page.
This not only wears the NAND out faster, but also degrades
performances, since reading a full PEB + writing it back to a different
PEB + erasing the old one is much more expensive than re-reading the
faulty page in raw mode and comparing it to the corrected buffer.
In most cases, the actual number of bitflips does not exceed the
bitflips threshold, and UBI won't have to move data around. Otherwise,
we can assume the time spent re-reading the page and doing the
comparison is negligible compared to the time UBI spends moving a full
PEB to another PEB.
Note that this logic is not applied to chips with 8bits/512byte on-die
ECC, because those chips provide fine-grained information (the maximum
error is 1 bit, and it will not force UBI to move blocks around at the
first bitflip).
Suggested-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some Micron NAND chips have on-die ECC forceably enabled. Allow such
chips to be used as long as the controller has set chip->ecc.mode to
NAND_ECC_ON_DIE.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some implementations simply can't disable their ECC engine. Expose
helpers returning -ENOTSUPP so that the caller knows that raw accesses
are not supported instead of silently falling back to non-raw
accessors.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Micron MT29F1G08ABAFAWP-ITE:F supports an on-die ECC with 8 bits
per 512 bytes. Add support for this combination.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Basing the "mandatory on-die" detection on ID byte 2 does not work,
because Micron has plenty of NANDs using the same device ID code, and
not all of them have forcibly enabled on-die ECC.
Since the "Array Operation" feature does not provide the "ECC
enabled/disabled" bit when the ECC can't be disabled, let's try to use
the "ECC enabled/disabled" bit in the READ_ID bytes.
It seems that this bit is dynamically updated on NANDs where on-die ECC
can freely be enabled/disabled, so let's hope it stays at one when we
have a NAND with on-die ECC forcibly enabled.
Fixes: 51f3b3970a8c ("mtd: rawnand: micron: detect forced on-die ECC")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
chip->read_buf is left unassigned since commit 4da712e702 ("mtd: nand:
fsmc: use ->exec_op()"), leading to a NULL pointer dereference when it's
called from fsmc_read_page_hwecc(). Fix that by using the appropriate
helper to read data out of the NAND.
Fixes: 4da712e702 ("mtd: nand: fsmc: use ->exec_op()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Compile-testing this driver on x86 caused a link error:
ERROR: "__phys_to_dma" [drivers/mtd/nand/raw/qcom_nandc.ko] undefined!
The problem here is that the driver attempts to convert the physical
address into the DMA controller as a dma_addr_t and calls phys_to_dma()
to do the conversion.
The correct way to do the conversion is using the dma mapping interfaces.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Tegra driver currently only support a single chip select, hence
check boundaries accordingly. This fixes a off by one issue catched
with Smatch:
drivers/mtd/nand/raw/tegra_nand.c:476 tegra_nand_select_chip()
warn: array off by one? 'nand->cs[die_nr]'
Also warn in case the stack asks for a chip select we currently do
not support.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some timings like tBERS (block erase time), tCCs (change column setup
time), tPROG (page program time) and tR (page read time) are derived
from the ONFI parameter page. They are set in the SDR interface only
if the chip is ONFI compliant.
It makes these timings unreliable and prevent the driver to use one of
these four values with a non-ONFI chip.
Fix this situation by taking the highest possible value (or a default
one) value for each missing timing (stored as unsigned 16-bit entries in
the parameter page).
This makes tBERS and tPROG being ~65ms while typical values are at most
a few milliseconds. As these are timeouts, it is not impacting at all
the performances in nominal use.
tR maximum time and tCCS minimum time (delay to wait after a change
column) are set, according to the ONFI specification, to default 'slow'
values; respectively 200us and 500ns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If driver doesn't specify parsers it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If driver doesn't specify parsers it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We already have a dependency on BCMA_NFLASH, which in turn depends on
BCMA, but since BCMA is a tristate option and BCMA_NFLASH is bool,
we can run into an invalid configuration with MTD_NAND_BCM47XXNFLASH=y
and BCMA=m:
drivers/mtd/nand/raw/bcm47xxnflash/ops_bcm4706.o: In function `bcm47xxnflash_ops_bcm4706_init':
ops_bcm4706.c:(.text+0x790): undefined reference to `bcma_chipco_pll_read'
Adding the dependency here forces MTD_NAND_BCM47XXNFLASH to only be
configured =m here so it can link against the BCMA driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In jz_nand_detect_bank(), chipnr is a size_t argument. Use %zu instead
of %i when printing it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This MACH_JZ4780 dependency is taken care of by JZ4780_NEMC, no need
to repeat it here.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having MACH_JZ4740 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This way we will be able to compile the jz4740_nand driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having SOC_TX4938 or SOC_TX4939
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This way we will be able to compile the ndfmc driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes maintainers' life easier by allowing them to compile-test
this driver without having FSL_SOC, ARCH_LAYERSCAPE or SOC_LS1021A
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The local eccstat_regs variable in fsl_ifc_run_command() is missing an
__iomem specifier, and sparce complains about that.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having PLAT_SPEAR, ARCH_NOMADIK,
ARCH_U8500 or MACH_U300 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
uintptr_t should be used when casting a pointer to an unsigned int so
that the code compiles without warnings even on 64-bit architectures.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We want to allow this driver to be selected when COMPILE_TEST=y, this
means the driver can be compiled for any arch, including MIPS. When
compiling this driver for MIPS, we end up with a collision on the 'PC'
macro definition (also defined in arch/mips/include/asm/ptrace.h).
Prefix the fsmc one with FSMC_ to avoid this problem.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_SUNXI enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes the following smatch warning:
drivers/mtd/nand/raw/sunxi_nand.c:551 sunxi_nfc_read_byte() error: uninitialized symbol 'ret'.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes the "warning: large integer implicitly truncated to unsigned type
[-Woverflow]" warning when compiled for x86.
This is needed in order to allow compiling this driver when
COMPILE_TEST=y.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_DAVINCI or ARCH_KEYSTONE
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Rules about Kconfig are simple but in the raw NAND directory indentation
is somehow archaic. Fix the indentation in the whole file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
uintptr_t should be used when casting a pointer to an unsigned int so
that the code compiles without warnings even on 64-bit architectures.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no point in doing this sort of conversion since we can
replace |= by += operations which are perfectly valid on pointers.
This is done in preparation of COMPILE_TEST addition to the NAND_DAVINCI
Kconfig entry, since building for x86 generates several warnings because
of inappropriate u32 <-> void * conversions (pointers are 64-bit large
on x86_64).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_AT91 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gen_pool_dma_alloc() return type is void *, while internally, the
memory region exposed by the sram driver has been mapped with
ioremap().
Add a void * to void __iomem * cast to make sparse happy.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When casting a pointer to an unsigned int, uintptr_t should be used to
cope with the pointer size differences between 32-bit and 64-bit
architectures.
This is needed if we want to allow compilation of this driver when
COMPILE_TEST=y.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Modern NAND controller drivers implement ->exec_op() instead of
->cmdfunc(), make sure we don't end up with a NULL pointer dereference
when hynix_nand_reg_write_op() is called.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Don't keep an error-pointer around in the private struct. If this optional
clock can't be obtained, simply set the pointer to NULL instead so we can
use clk_prepare_enable() on it without further checks,
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The comment in marvell_nfc_select_chip() about ndtr0 and ndtr1 didn't
reflect what the driver was doing.
The values of NDTR0 and NDTR1 are read from the registers at probe time
and a copy is retained in 'struct marvell_nand_chip'. If keep-config is
set in the DT properties, there are no other writers of these timing
variables so they can safely be used when the chip is selected.
As suggested by Miquel Raynal, simply remove the comment.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch restores the suspend and resume hooks that the old driver used
to have. Apart from stopping and starting the clocks, the resume callback
also nullifies the selected_chip pointer, so the next command that is issued
will re-select the chip and thereby restore the timing registers.
Factor out some code from marvell_nfc_init() into a new function
marvell_nfc_reset() and also call it at resume time to reset some registers
that don't retain their contents during low-power mode.
Without this patch, a PXA3xx based system would cough up an error similar to
the one below after resume.
[ 44.660162] marvell-nfc 43100000.nand-controller: Timeout waiting for RB signal
[ 44.671492] ubi0 error: ubi_io_write: error -110 while writing 2048 bytes to PEB 102:38912, written 0 bytes
[ 44.682887] CPU: 0 PID: 1417 Comm: remote-control Not tainted 4.18.0-rc2+ #344
[ 44.691197] Hardware name: Marvell PXA3xx (Device Tree Support)
[ 44.697111] Backtrace:
[ 44.699593] [<c0106458>] (dump_backtrace) from [<c0106718>] (show_stack+0x18/0x1c)
[ 44.708931] r7:00000800 r6:00009800 r5:00000066 r4:c6139000
[ 44.715833] [<c0106700>] (show_stack) from [<c0678a60>] (dump_stack+0x20/0x28)
[ 44.724206] [<c0678a40>] (dump_stack) from [<c0456cbc>] (ubi_io_write+0x3d4/0x630)
[ 44.732925] [<c04568e8>] (ubi_io_write) from [<c0454428>] (ubi_eba_write_leb+0x690/0x6fc)
...
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the board files are overloading those hooks, so let's drop them
from struct platform_nand_ctrl.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the boards seem to overload the ->dev_ready() hook, just drop
this field from orion_nand_data.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the existing drivers are overloading the ->scan_bbt() method,
let's get rid of it and replace calls to ->scan_bbt() by
nand_create_bbt() ones.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Rename nand_default_bbt() into nand_create_bbt() and pass it a nand_chip
object to prepare removal of the chip->scan_bbt() hook.
We add a temporary nand_default_bbt() wrapper which will be dropped
after the removal of ->scan_bbt().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Leaving a function pointer to NULL should be enough to trigger a NULL
pointer exception, and anyway, if we want to BUG() when some missing
hooks are called, this should be done in the core, so let's drop the
cafe_nand_bug() dummy function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_W90X900 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_QCOM enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_MXC enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
asm/mach/flash.h does not seem to be needed, drop this #include to make
the code completely machine and arch independent and allow one to
compile it when COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARM, ARM64 or MIPS enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test these drivers without having ARCH_LPC32XX enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_PXA enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't need mach/hardware.h and sm/mach-types.h, and asm/io.h can be
replaced by linux/io.h.
Now that we removed those inclusions, we're ready to allow selection of
this driver when COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_OMAP2PLUS or ARCH_KEYSTONE
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When COMPILE_TEST is allowed and the platform needs uses the iomem API
we need to add an explicit dependency on HAS_IOMEM to avoid selection
of these drivers when building for an arch that has no iomem support
(this is the case of arch/um).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The MTD_NAND_GPMI_NAND entry is already defined in an 'if MTD_NAND'
block, no need to add an extra "depends on MTD_NAND".
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NAND parts can have bitflips in an erased page due to the
process technology used. In this case, QCOM NAND controller
is not able to identify that page as an erased page.
Currently the driver calls nand_check_erased_ecc_chunk() for
identifying the erased pages but this won’t work always since the
checking is being with ECC engine returned data. In case of
bitflips, the ECC engine tries to correct the data and then it
generates the uncorrectable error. Now, this data is not equal to
original raw data. For erased CW identification, the raw data
should be read again from NAND device and this
nand_check_erased_ecc_chunk function() should be called for raw
data only.
Now following logic is being added to identify the erased
codeword bitflips.
1. In most of the cases, not all the codewords will have bitflips
and only single CW will have bitflips. So, there is no need to
read the complete raw page data. The NAND raw read can be
scheduled for any CW in page. The NAND controller works on CW
basis and it will update the status register after each CW read.
Maintain the bitmask for the CW which generated the uncorrectable
error.
2. Do raw read for all the CW's which generated the uncorrectable
error.
3. Both DATA and OOB need to be checked for number of 0. The
top-level API can be called with only data buf or OOB buf so use
chip->databuf if data buf is null and chip->oob_poi if
OOB buf is null for copying the raw bytes temporarily.
4. For each CW, check the number of 0 in cw_data and usable
oob bytes, The bbm and spare (unused) bytes bit flip won’t
affect the ECC so don’t check the number of bitflips in this area.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Variable payload_virt is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'payload_virt' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_release() should not be called on an MTD device that has not been
registered. While it should work thanks to the checks done in
mtd_device_unregister() it's a bad practice to cleanup/release
something that has not previously been initialized/allocated.
Rework the error path to follow this rule.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This commit improves the ->setup_data_interface() hook.
The denali_setup_data_interface() needs the frequency of clk_x
and the ratio of clk_x / clk.
The latter is currently hardcoded in the driver, like this:
#define DENALI_CLK_X_MULT 6
The IP datasheet requires that clk_x / clk be 4, 5, or 6. I just
chose 6 because it is the most defensive value, but it is not optimal.
By getting the clock rate of both "clk" and "clk_x", the driver can
compute the timing values more precisely.
To not break the existing platforms, the fallback value, 50 MHz is
provided. It is true for all upstreamed platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, denali_dt.c requires a single anonymous clock, but
the Denali User's Guide requires three clocks for this IP:
- clk: controller core clock
- clk_x: bus interface clock
- ecc_clk: clock at which ECC circuitry is run
This commit supports these named clocks to represent the real hardware.
For the backward compatibility, the driver still accepts a single clock
just as before. The clk_x_rate is taken from the clock driver again if
the named clock "clk_x" is available. This will happen only for future
DT, hence the existing DT files are not affected.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function references &pdev->dev many times, and I will add
more soon. Add 'dev' as a shorthand.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Using the sysfs unbind, bind nodes, mxcnd_probe and mxcnd_probe_dt can
potentially be called at any time. After the __init functions are cleaned,
mxcnd_probe_dt is no longer available. Calling it anyway causes a crash.
mxcnd_probe used to be marked as __init, this was removed years ago.
Remove the __init qualifier from from mxcnd_probe_dt as well.
Fixes: 06f2551069 ("mtd: remove use of __devinit")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
MX35LF2GE4AB is almost identical to MX35LF1GE4AB except it has 2 times
more eraseblocks per LUN and exposes 2 planes instead of 1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add minimal support for the MX35LF1GE4AB SPI NAND chip.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for the W25M02GV chip.
Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a basic driver for Micron SPI NANDs. Only one device is supported
right now, but the driver will be extended to support more devices
afterwards.
Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a SPI NAND framework based on the generic NAND framework and the
spi-mem infrastructure.
In its current state, this framework supports the following features:
- single/dual/quad IO modes
- on-die ECC
Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Function nand_ecc_choose_conf() will be help for all the cases, so
other helper functions can be made static.
nand_check_ecc_caps(): Invoke nand_ecc_choose_conf() with
both chip->ecc.size and chip->ecc.strength
value set.
nand_maximize_ecc(): Invoke nand_ecc_choose_conf() with
NAND_ECC_MAXIMIZE flag.
nand_match_ecc_req(): Invoke nand_ecc_choose_conf() with either
chip->ecc.size or chip->ecc.strength value
set and without NAND_ECC_MAXIMIZE flag.
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make separate function to perform raw read for one codeword and
call this function multiple times for each codeword in case of
raw page read. This separate function will help in subsequent
patches related with erased codeword bitflip detection.
It will decrease throughput for raw page read. Raw page read
is used for debug purpose so it won't affect normal flash
operations.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently there is no error checking for raw read. For raw
reads, there won’t be any ECC failure but the operational
failures are possible, so schedule the NAND_FLASH_STATUS read
after each codeword.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix value returned by ->read_page_raw() to be the
actual operation status, instead of always 0.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
QCOM NAND controller layout protects available OOB data bytes with
ECC also so when ecc->write_oob() is being called then it
can't update just OOB bytes. Currently, it first reads the last
codeword which includes old OOB bytes. Then it updates the old OOB
bytes with new ones and then again writes the codeword back.
The reading codeword is unnecessary since user is responsible to
have these bytes cleared to 0xFF.
This patch removes the read part and updates the OOB bytes with
data area padded with OxFF.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
read_page and read_oob both calls the read_page_ecc function.
The QCOM NAND controller protect the OOB available bytes with
ECC so read errors should be checked for read_oob also.
This patch moves the error checking code inside read_page_ecc
so caller does not have to check explicitly for read errors.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
parse_read_errors can be called with only oob_buf in which case
data_buf will be NULL. If data_buf is NULL, then don’t
treat this page as completely erased in case of ECC uncorrectable
error for RS ECC. For BCH ECC, the controller itself tells
regarding erased page in status register.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Following is the flow in the HW if controller tries to read erased
page:
1. First ECC uncorrectable error will be generated from ECC engine
since ECC engine first calculates the ECC with all 0xff and match
the calculated ECC with ECC code in OOB (which is again all 0xff).
2. After getting ECC error, erased CW detection logic will be
applied which is different for BCH and RS ECC
a. For BCH, HW checks if all the bytes in page are 0xff and then
it updates the status in separate register
NAND_ERASED_CW_DETECT_STATUS.
b. For RS ECC, the HW reports the same error when reading an
erased CW, but it notifies that it is an erased CW by
placing special characters at certain offsets in the
buffer.
So the erased CW detect status should be checked only if ECC engine
generated the uncorrectable error.
Currently for all other operational errors also (like TIMEOUT, MPU
errors, etc.), the erased CW detect logic is being applied so fix this
and return EIO for other operational errors.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The BAM has 3 channels - tx, rx and command. command channel
is used for register read/writes, tx channel for data writes
and rx channel for data reads. Currently, the driver assumes the
transfer completion once it gets all the command descriptors
completed. Sometimes, there is race condition between data channel
(tx/rx) and command channel completion. In these cases,
the data present in buffer is not valid during small window
between command descriptor completion and data descriptor
completion.
This patch generates NAND transfer completion when both
(Data and Command) DMA channels have completed all its DMA
descriptors. It assigns completion callback in last
DMA descriptors of that channel and wait for completion.
Fixes: 8d6b6d7e13 ("mtd: nand: qcom: support for command descriptor formation")
Cc: stable@vger.kernel.org
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently the driver uses the ECC strength specified in DT.
The QPIC/EBI2 NAND supports 4 or 8-bit ECC correction. The same
kind of board can have different NAND parts so use the ECC
strength from device parameters if it is not specified in DT.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
QCOM NAND controller supports only one step size (512) so
nand-ecc-step-size DT property is redundant. This property
can be removed and ecc step size can be assigned with 512 value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the NAND core helper function nand_ecc_choose_conf to tune
the ECC parameters instead of the function locally defined.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
commit 2c8f8afa7f ("mtd: nand: add generic helpers to check,
match, maximize ECC settings") provides generic helpers which
drivers can use for setting up ECC parameters.
Since same board can have different ECC strength nand chips so
following is the logic for setting up ECC strength and ECC step
size, which can be used by most of the drivers.
1. If both ECC step size and ECC strength are already set
(usually by DT) then just check whether this setting
is supported by NAND controller.
2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength
supported by NAND controller.
3. Otherwise, try to match the ECC step size and ECC strength closest
to the chip's requirement. If available OOB size can't fit the chip
requirement then select maximum ECC strength which can be fit with
available OOB size.
This patch introduces nand_ecc_choose_conf function which calls the
required helper functions for the above logic. The drivers can use
this single function instead of calling the 3 helper functions
individually.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Micron NAND chips (MT29F1G08ABAFAWP-ITE:F) report 00 00 for the
revision number field of the ONFI parameter page. Rather than rejecting
these outright assume ONFI version 1.0 if the revision number is 00 00.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add defines for the ONFI version bits and use them in
nand_flash_detect_onfi().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This is called after the ONFI parameter page checksum is verified
and allows us to override the contents of the parameter page.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
>From the controllers point of view this is the same as no or
software only ECC.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for the NAND flash controller found on NVIDIA
Tegra 2 SoCs. This implementation does not make use of the
command queue feature. Regular operations using ->exec_op()
use PIO mode for data transfers. Raw, ECC and OOB read/writes
make use of the DMA mode for data transfer.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add Reed-Solomon (RS) to the enumeration of ECC algorithms.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The datasheet of the H27UCG8T2BTR states that this chip has a page size
of "16,384 + 1,280(Spare) bytes". The description of the "4th Byte of
Device Identifier Description" indicates that bits 6, 3 and 2 are
encoding the "Redundant Area Size / 8KB", where 640 bytes is a value of
0x6 (110 in binary notation).
hynix_nand_extract_oobsize decodes an OOB size of 640 bytes for this
chip. Kernel boot log extract before this patch:
nand: Could not find valid ONFI parameter page; aborting
nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde
nand: Hynix NAND 8GiB 3,3V 8-bit
nand: 8192 MiB, MLC, erase size: 4096 KiB, page size: 16384,
OOB size: 640
However, based on the description in the datasheet we need to multiply
the OOB size with 2, because it's "640 spare bytes per 8192 bytes page
size" and this NAND chip has a page size of 16384 (= 2 * 8192). After
this patch the kernel boot log reports:
nand: Could not find valid ONFI parameter page; aborting
nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde
nand: Hynix NAND 8GiB 3,3V 8-bit
nand: 8192 MiB, MLC, erase size: 4096 KiB, page size: 16384,
OOB size: 1280
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Even if we can't update ecc_stats.corrected with an accurate value we
should at least increase the number of bitflips so that MTD users can
know that there was some bitflips.
Just add chip->ecc.strength to mtd->ecc_stats.corrected which should
account for the worst case situation.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
On a sama5d31 with a Full-HD dual LVDS panel (132MHz pixel clock) NAND
flash accesses have a tendency to cause display disturbances. Add a
module param to disable DMA from the NAND controller, since that fixes
the display problem for me.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 1bb8866677 ("mtd: nand: denali: handle timing parameters
by setup_data_interface()"), denali_dt.c gets the clock rate from the
clock driver. The driver expects the frequency of the bus interface
clock, whereas the clock driver of SOCFPGA provides the core clock.
Thus, the setup_data_interface() hook calculates timing parameters
based on a wrong frequency.
To make it work without relying on the clock driver, hard-code the clock
frequency, 200MHz. This is fine for existing DT of UniPhier, and also
fixes the issue of SOCFPGA because both platforms use 200 MHz for the
bus interface clock.
Fixes: 1bb8866677 ("mtd: nand: denali: handle timing parameters by setup_data_interface()")
Cc: linux-stable <stable@vger.kernel.org> #4.14+
Reported-by: Philipp Rosenberger <p.rosenberger@linutronix.de>
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Make sure we flag all broken chips as not supporting this feature.
Also move this logic to a new function to keep things readable.
Fixes: 34c5c01e0c ("mtd: rawnand: macronix: nack the support of changing timings for one chip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Positive return value from read_oob() is making false BAD
blocks. For some of the NAND controllers, OOB bytes will be
protected with ECC and read_oob() will return number of bitflips.
If there is any bitflip in ECC protected OOB bytes for BAD block
status page, then that block is getting treated as BAD.
Fixes: c120e75e0e ("mtd: nand: use read_oob() instead of cmdfunc() for bad block check")
Cc: <stable@vger.kernel.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The v21 version of the NAND flash controller contains a Spare Area Size
Register (SPAS) at offset 0x10. Its setting defaults to the maximum
spare area size of 218 bytes. The size that is set in this register is
used by the controller when it calculates the ECC bytes internally in
hardware.
Usually, this register is updated from settings in the IIM fuses when
the system is booting from NAND flash. For other boot media, however,
the SPAS register remains at the default setting, which may not work for
the particular flash chip on the board. The same goes for flash chips
whose configuration cannot be set in the IIM fuses (e.g. chips with 2k
sector size and 128 bytes spare area size can't be configured in the IIM
fuses on imx25 systems).
Set the SPAS register explicitly during the preset operation. Derive the
register value from mtd->oobsize that was detected during probe by
decoding the flash chip's ID bytes.
While at it, rename the define for the spare area register's offset to
NFC_V21_RSLTSPARE_AREA. The register at offset 0x10 on v1 controllers is
different from the register on v21 controllers.
Fixes: d484018 ("mtd: mxc_nand: set NFC registers after reset")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add ONFI_FEATURE_ON_DIE_ECC to the set/get features list for Micron
NAND flash.
Fixes: 789157e41a ("mtd: rawnand: allow vendors to declare (un)supported features")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=zUUp
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
Here are the main updates for SoC support (besides DT additions) for ARM
32- and 64-bit platforms. The branch also contains defconfig updates to
turn on drivers and options as needed on the various platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products.
-----BEGIN PGP SIGNATURE-----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=S5wc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Here are the main updates for SoC support (besides DT additions) for
ARM 32- and 64-bit platforms. The branch also contains defconfig
updates to turn on drivers and options as needed on the various
platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
MAINTAINERS: add NXP linux team maillist as i.MX reviewer
ARM: stm32: Don't select DMA unconditionally on STM32MP157C
arm64: defconfig: Enable PCIe on msm8996 and db820c
ARM: pxa3xx: enable external wakeup pins
ARM: pxa: stargate2: use device properties for at24 eeprom
arm64: defconfig: Enable HISILICON_LPC
arm64: defconfig: enable drivers for Poplar support
arm64: defconfig: Enable UFS on msm8996
ARM: berlin: switch to SPDX license identifier
arm: berlin: remove non-necessary flush_cache_all()
ARM: berlin: extend BG2CD Kconfig entry
OMAP: CLK: CLKSRC: Add suspend resume hooks
ARM: AM43XX: Add functions to save/restore am43xx control registers
ASoC: ams_delta: use GPIO lookup table
ARM: OMAP1: ams-delta: add GPIO lookup tables
bus: ti-sysc: Fix optional clocks array access
ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared
ARM: OMAP2+: prm44xx: Inroduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: prm44xx: Introduce context save/restore for am43 PRCM IO
ARM: OMAP2+: powerdomain: Introduce cpu_pm notifiers for context save/restore
...
Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND changes:
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR changes:
Core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
-----BEGIN PGP SIGNATURE-----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=cHjU
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
-----BEGIN PGP SIGNATURE-----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=MzWF
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.18' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
Mainly contains patches to move NAND chipselect to platform data
(currently platform device id is being used). These patches have
been acked by NAND maintainer and because of the driver dependency
an immutable branch has been provided to Boris.
The other patch is to remove an unnecessary postcore_initcall() on
DM644x which is needed for common clock framework conversion.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iWsm
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.18/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
DaVinci SoC support updates for v4.18
Mainly contains patches to move NAND chipselect to platform data
(currently platform device id is being used). These patches have
been acked by NAND maintainer and because of the driver dependency
an immutable branch has been provided to Boris.
The other patch is to remove an unnecessary postcore_initcall() on
DM644x which is needed for common clock framework conversion.
* tag 'davinci-for-v4.18/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm644x: remove unnecessary postcore_initcall()
ARM: davinci: aemif: stop using pdev->id as nand chipselect
mtd: rawnand: davinci: stop using pdev->id as chipselect
ARM: davinci: neuros-osd2: specify the chipselect in davinci_nand_pdata
ARM: davinci: dm646x-evm: specify the chipselect in davinci_nand_pdata
ARM: davinci: mityomapl138: specify the chipselect in davinci_nand_pdata
ARM: davinci: dm644x-evm: specify the chipselect in davinci_nand_pdata
ARM: davinci: dm365-evm: specify the chipselect in davinci_nand_pdata
ARM: davinci: dm355-leopard: specify the chipselect in davinci_nand_pdata
ARM: davinci: dm355-evm: specify the chipselect in davinci_nand_pdata
ARM: davinci: da850-evm: specify the chipselect in davinci_nand_pdata
ARM: davinci: da830-evm: specify the chipselect in davinci_nand_pdata
mtd: rawnand: davinci: store the core chipselect number in platform data
Signed-off-by: Olof Johansson <olof@lixom.net>
The ONFI spec clearly says that FAIL bit is only valid for PROGRAM,
ERASE and READ-with-on-die-ECC operations, and should be ignored
otherwise.
It seems that checking it after sending a SET_FEATURES is a bad idea
because a previous READ, PROGRAM or ERASE op may have failed, and
depending on the implementation, the FAIL bit is not cleared until a
new READ, PROGRAM or ERASE is started.
This leads to ->set_features() returning -EIO while it actually worked,
which can sometimes stop a batch of READ/PROGRAM ops.
Note that we only fix the ->exec_op() path here, because some drivers
are abusing the NAND_STATUS_FAIL flag in their ->waitfunc()
implementation to propagate other kind of errors, like
wait-ready-timeout or controller-related errors. Let's not try to fix
those drivers since they worked fine so far.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
The code is doing monolithic reads for all chunks except the last one
which is wrong since a monolithic read will issue the
READ0+ADDRS+READ_START sequence. It not only takes longer because it
forces the NAND chip to reload the page content into its internal
cache, but by doing that we also reset the column pointer to 0, which
means we'll always read the first chunk instead of moving to the next
one.
Rework the code to do a monolithic read only for the first chunk,
then switch to naked reads for all intermediate chunks and finally
issue a last naked read for the last chunk.
Fixes: 02f26ecf8c mtd: nand: add reworked Marvell NAND controller driver
Cc: stable@vger.kernel.org
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Per ONFI specification (Rev. 4.0), if all parameter pages have invalid
CRC values, the bit-wise majority may be used to recover the contents
of the parameter page from the parameter page copies present.
Signed-off-by: Jane Wan <Jane.Wan@nokia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
NAND chips require a bit of time to take the NAND operation into
account and set the BUSY bit in the STATUS reg. Make sure we don't poll
the STATUS reg too early in nand_soft_waitrdy().
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Per ONFI specification (Rev. 4.0), if the CRC of the first parameter page
read is not valid, the host should read redundant parameter page copies.
Fix FSL NAND driver to read the two redundant copies which are mandatory
in the specification.
Signed-off-by: Jane Wan <Jane.Wan@nokia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
One layout supported by the Marvell NAND controller supports NAND pages
of 2048 bytes, all handled in one single chunk when using BCH with a
strength of 4-bit per 512 bytes. In this case, instead of the generic
XTYPE_WRITE_DISPATCH/XTYPE_LAST_NAKED_RW couple, the controller expects
to receive XTYPE_MONOLITHIC_RW.
This fixes problems at boot like:
[ 1.315475] Scanning device for bad blocks
[ 3.203108] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 3.209564] nand_bbt: error while writing BBT block -110
[ 4.243106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 5.283106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 5.289562] nand_bbt: error -110 while marking block 2047 bad
[ 6.323106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 6.329559] nand_bbt: error while writing BBT block -110
[ 7.363106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 8.403105] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 8.409559] nand_bbt: error -110 while marking block 2046 bad
...
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
marvell_nfc_wait_op() expects the delay to be expressed in milliseconds
but nand_sdr_timings uses picoseconds. Use PSEC_TO_MSEC when passing
tPROG_max to marvell_nfc_wait_op().
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
dma_map_single does not work for vmalloc-ed buffers,
so disable DMA in this case.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reported-by: "H. Nikolaus Schaller" <hns@goldelico.com>
Tested-by: "H. Nikolaus Schaller" <hns@goldelico.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
All platform now use the core_chipsel field in platform data. Stop
using pdev->id in the driver.
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Use this->auxiliary_virt and this->auxiliary_phys directly rather
than creating extra local variables for them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The caller of bch_set_geometry() expects the return value to
be an error code, so !0 is not valid. return the error from the
just called function instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Instead of putting direct_dma_map_ok into driver struct pass it around
between functions to make the code more readable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
read_page_prepare(), read_page_end() and read_page_swap_end() are
trivial functions that are used only once and take 8 arguments each.
De-obfuscate the code by open coding these functions in
gpmi_ecc_read_page()
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Instead of putting the buffer and len passed in from the mtd core
into the private data struct, just pass it around in the GPMI
drivers functions. This makes the lifetime of the variables more
clear and the code easier to follow.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The GPMI nand driver puts dma_ops_type in its private data struct. Based
on the ops type the DMA callback handler unmaps previously mapped
buffers. Instead of unmapping the buffers in the DMA callback handler,
do this in the caller directly which waits for the DMA transfer to
finish. This makes the whole dma_ops_type mechanism unnecessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
As part of the work of migrating all the drivers to nand_scan(), and
because nand_scan() does not provide a way to pass an ID table, rename
the function nand_scan_with_ids() and add a third parameter to give a
flash ID table (like what was done with nand_scan_ident()).
Create a nand_scan() helper that is just a wrapper of
nand_scan_with_ids(), passing NULL as the ID table. This way a
controller drivers can continue using nand_scan() transparently.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup() and not
a nand_release(). The latter doing an mtd_device_unregister() which is
not needed if mtd_device_register() failed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Before fixing the error path of the probe function, fix the style of the
entire function and particularly the goto labels: they should indicate
what the next cleanup to do is.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup() and not
a nand_release(). The latter doing an mtd_device_unregister() which is
not needed if mtd_device_register() failed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Before fixing the error path of the probe function, fix the style of the
entire function and particularly the goto labels: they should indicate
what the next cleanup to do is.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup() and not
a nand_release(). The latter doing an mtd_device_unregister() which is
not needed if mtd_device_register() failed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
There is not need for a goto statement when the only action to take is
to return.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Before fixing the error path of the probe function, fix the style of the
probe function and mostly the goto labels: they should indicate what
the next cleanup is, not the point from which they can be accessed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
However, in this driver, fsl_ifc_chip_remove() which is called upon
error already triggers a nand_release() which is wrong, because a
nand_release() should be triggered only if an mtd_register() succeeded.
Move the nand_release() call out of the fsl_ifc_chip_remove() and put it
back in the *_remove() hook.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
However, in this driver, fsl_elbc_chip_remove() which is called upon
error already triggers a nand_release() which is wrong, because a
nand_release() should be triggered only if an mtd_register() succeeded.
Move the nand_release() call out of the fsl_elbc_chip_remove() and put
it back in the *_remove() hook.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call .probe() is to match an entry in
.of_match_table[], so of_device_id cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
doc_probe() is never called in atomic context.
doc_probe() is only called by init_nanddoc(), which is only set as
a parameter of module_init().
This function is not called in atomic context.
Despite never getting called from atomic context, doc_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
None of the existing platforms connect the R/B pin to a GPIO (they all
use one of the dedicated R/B pin).
Anyway, if we ever get short of native R/B pins, it's probably better
to fallback to STATUS reg polling than trying to poll a GPIO.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add support for specified ECC strength/size using device tree
properties nand-ecc-strength/nand-ecc-step-size.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
NAND itself is an asynchronous interface, it does not have any
clock input. DaVinci NAND driver acquires clock for AEMIF
(asynchronous external memory interface) which is an on-chip
IP to which NAND is connected.
The same clock is also enabled in AEMIF driver (either present
drivers/memory or from machine code for some older platforms).
AEMIF timing must be initialized before NAND can be accessed.
This ensures that AEMIF clock is enabled too.
Remove the superfluous clock acquisition and enable in DaVinci
NAND driver.
Tested on K2L, K2HK, K2E, DA850 EVM, DA850 LCDK in device-tree
boot and DM644x EVM in legacy boot.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The block responsible of parsing the DT for the number of chip-select
lines uses an 'if/else if/else if' block. The content of the second and
third 'else if' conditions are:
1/ the actual condition to enter the sub-block and
2/ the operation to do in this sub-block.
[...]
else if (condition1_to_enter && action1() == failed)
raise_error();
else if (condition2_to_enter && action2() == failed)
raise_error();
[...]
In case of failure, the sub-block is entered and an error raised.
Otherwise, in case of success, the code would continue erroneously in
the next 'else if' statement because it did not failed (and did not
enter the first 'else if' sub-block).
The first 'else if' refers to legacy bindings while the second 'else if'
refers to new bindings. The second 'else if', which is entered
erroneously, checks for the 'reg' property, which, for old bindings,
does not mean anything because it would not be the number of CS
available, but the regular register map of almost any DT node. This
being said, the content of the 'reg' property being the register map
offset and length, it has '2' values, so the number of CS in this
situation is assumed to be '2'.
When running nand_scan_ident() with 2 CS, the core will check for an
array of chips. It will first issue a RESET and then a READ_ID. Of
course this will trigger two timeouts because there is no chip in front
of the second CS:
[ 1.367460] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000080)
[ 1.474292] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000280)
Indeed, this is harmless and the core will then assume there is only one
valid CS.
Fix the logic in the whole block by entering each sub-block just on the
'is legacy' condition, doing the action inside the sub-block. This way,
when the action succeeds, the whole block is left.
Furthermore, for both the old bindings and the new bindings the same
logic was applied to retrieve the number of CS lines:
using of_get_property() to get a size in bytes, converted in the actual
number of lines by dividing it per sizeof(u32) (4 bytes).
This is fine for the 'reg' property which is a list of the CS IDs but
not for the 'num-cs' property which is directly the value of the number
of CS.
Anyway, no existing DT uses another value than 'num-cs = <1>' and no
other value has ever been supported by the old driver (pxa3xx_nand.c).
Remove this condition and apply a number of 1 CS anyway, as already
described in the bindings.
Finally, the 'reg' property of a 'nand' node (with the new bindings)
gives the IDs of each CS line in use. marvell_nand.c driver first look
at the number of CS lines that are present in this property.
Better use of_property_count_elems_of_size() than dividing by 4 the size
of the number of bytes returned by of_get_property().
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The reed solomon library is moving the on stack decoder buffers into the rs
control structure. That would break the DoC driver because multiple
instances share the same control structure and can operate in parallel. At
least in theory....
Instantiate a rs control instance per DoC device to avoid that. The per
instance buffer is fine as the operation on a single DoC instance is
serialized by the MTD/NAND core.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Kernel Hardening <kernel-hardening@lists.openwall.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Andrew Morton <akpm@linuxfoundation.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
The decoder library uses variable length arrays on stack. To get rid of
them it would be simple to allocate fixed length arrays on stack, but those
might become rather large. The other solution is to allocate the buffers in
the rs control structure, but this cannot be done as long as the structure
can be shared by several users. Sharing is desired because the RS polynom
tables are large and initialization is time consuming.
To solve this split the codec information out of the control structure and
have a pointer to a shared codec in it. Instantiate the control structure
for each user, create a new codec if no shareable is avaiable yet. Adjust
all affected usage sites to the new scheme.
This allows to add per instance decoder buffers to the control structure
later on.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Kernel Hardening <kernel-hardening@lists.openwall.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Andrew Morton <akpm@linuxfoundation.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Commit e7bfb3fdbd ("mtd: Stop updating erase_info->state and calling
mtd_erase_callback()") removed the einfo->state field and the
MTD_ERASE_XXX macros. At the same time, the generic NAND layer was added
and made sure to update the erase info state.
It did not result in a build failure after merging the nand/for-4.17
branch in mtd/next because the generic NAND layer is not selected yet.
Let's fix that before a config option starts selecting MTD_NAND_CORE.
Fixes: e7bfb3fdbd ("mtd: Stop updating erase_info->state and calling mtd_erase_callback()")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Use devm_clk_get() to let Linux manage struct clk memory.
Fixes: 6956e2385a ("add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Reported-by: Xidong Wang <wangxidong_97@163.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Core:
* Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
* Remove Cyrille from the list of SPI NOR and MTD maintainers
* Fix kernel doc headers
* Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
* Remove the bfin-async-flash driver (the only architecture using
it has been removed)
* Fix pagetest test
* Add extra checks in mtd_erase()
* Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
Drivers:
* Add endianness information to the physmap DT binding
* Add Eon EN29LV400A IDs to JEDEC probe logic
* Use %*ph where appropriate
SPI NOR changes:
Drivers:
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND changes:
Core:
* Prepare arrival of the SPI NAND subsystem by implementing a
generic (interface-agnostic) layer to ease manipulation of NAND
devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Drivers:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=EG7L
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD Core:
- Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
- Remove Cyrille from the list of SPI NOR and MTD maintainers
- Fix kernel doc headers
- Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
- Remove the bfin-async-flash driver (the only architecture using it
has been removed)
- Fix pagetest test
- Add extra checks in mtd_erase()
- Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
MTD Drivers:
- Add endianness information to the physmap DT binding
- Add Eon EN29LV400A IDs to JEDEC probe logic
- Use %*ph where appropriate
SPI NOR Drivers:
- Make fsl-quaspi assign different names to MTD devices connected to
the same QSPI controller
- Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND Core:
- Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
- Move onenand code base to the drivers/mtd/nand/ dir
- Rework timing mode selection
- Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
- Stop embedding ONFI/JEDEC param page in nand_chip
NAND Drivers:
- Rework/cleanup of the mxc driver
- Various cleanups in the vf610 driver
- Migrate the fsmc and vf610 to ->exec_op()
- Get rid of the pxa driver (replaced by marvell_nand)
- Support ->setup_data_interface() in the GPMI driver
- Fix probe error path in several drivers
- Remove support for unused hw_syndrome mode in sunxi_nand
- Various minor improvements"
* tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd: (89 commits)
dt-bindings: fsl-quadspi: Add the example of two SPI NOR
mtd: fsl-quadspi: Distinguish the mtd device names
mtd: nand: Fix some function description mismatches in core.c
mtd: fsl-quadspi: Remove unneeded driver.bus assignment
mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
mtd: rawnand: s3c2410: enhance the probe function error path
mtd: rawnand: tango: fix probe function error path
mtd: rawnand: sh_flctl: fix the probe function error path
mtd: rawnand: omap2: fix the probe function error path
mtd: rawnand: mxc: fix probe function error path
mtd: rawnand: denali: fix probe function error path
mtd: rawnand: davinci: fix probe function error path
mtd: rawnand: cafe: fix probe function error path
mtd: rawnand: brcmnand: fix probe function error path
mtd: rawnand: sunxi: Stop supporting ECC_HW_SYNDROME mode
mtd: rawnand: marvell: Fix clock resource by adding a register clock
mtd: ftl: Use DIV_ROUND_UP()
mtd: Fix some function description mismatches in mtdcore.c
mtd: physmap_of: update struct map_info's swap as per map requirement
dt-bindings: mtd-physmap: Add endianness supports
...
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqKKI0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGRNAH/0v3+nuJ0oiHE1Cl
fH89F9Ma17j8oTo28byRPi7X5XJfJAqANhHa209rguvnC27y3ew/l9k93HoxG12i
ttvyKFDQulQbytfJZXw8lhUyYGXVsTpyNaihPe/NtqPdIxNgfrXsUN9EIEtcnuS2
SiAj51jUySDRNR4ST6TOx4ulDm1zLrmA28WHOBNOTvDi4jTQMt1TsngHfF5AySBB
lD4RTRDDwWDWtdMI7euYSq019TiDXCxmwQ94vZjrqmjmSQcl/yCK/JzEV33SZslg
4WqGIllxONvP/UlwxZLaJ+RrslqxNgDVqQKwJdfYhGaWvpgPFtS1s86zW6IgyXny
02jJfD0=
=DLWn
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into mtd/next
Backmerge v4.16-rc2 into mtd/next to resolve a conflict between Linus'
master branch and nand/for-4.17.
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=uvio
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
In core.c, some function descriptions do not match function
definitions. Just fix these mismatches.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
get_sectorsize() was not using the appropriate macro to extract the
ECC sector size from the config cache, which led to buggy ECC when
using 1024 byte sectors.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Reported-by: Olivier Schonken <olivier.schonken@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Olivier Schonken <olivier.schonken@gmail.com>
The core clock field was badly named ->ecc_clk which might lead to some
confusion. Rename it ->core_clk.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Prepare the migration of the lpc32xx_slc driver to use nand_scan() by
cleaning the error path in the probe function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This mode is not used by any existing setup and should not be used
because it overwrites the BBMs. Let's just remove it before someone
starts using it.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The binding documentation is updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Due to missing information in Hardware manual, current
implementation doesn't read ECCSTAT0 and ECCSTAT1 registers
for IFC 2.0.
Add support to read ECCSTAT0 and ECCSTAT1 registers during
ecccheck for IFC 2.0.
Fixes: 656441478e ("mtd: nand: ifc: Fix location of eccstat registers for IFC V1.0")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Number of ECC status registers i.e. (ECCSTATx) has been increased in IFC
version 2.0.0 due to increase in SRAM size. This is causing eccstat
array to over flow.
So, replace eccstat array with u32 variable to make it fail-safe and
independent of number of ECC status registers or SRAM size.
Fixes: bccb06c353 ("mtd: nand: ifc: update bufnum mask for ver >= 2.0.0")
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
As per the IFC hardware manual, Most significant 2 bytes in
nand_fsr register are the outcome of NAND READ STATUS command.
So status value need to be shifted and aligned as per the nand
framework requirement.
Fixes: 82771882d9 ("NAND Machine support for Integrated Flash Controller")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
MTD users are no longer checking erase_info->state to determine if the
erase operation failed or succeeded. Moreover, mtd_erase_callback() is
now a NOP.
We can safely get rid of all mtd_erase_callback() calls and all
erase_info->state assignments. While at it, get rid of the
erase_info->state field, all MTD_ERASE_XXX definitions and the
mtd_erase_callback() function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
---
Changes in v2:
- Address a few coding style issues (reported by Miquel)
- Remove comments that are no longer valid (reported by Miquel)
GPMI driver timings derivation looks very empirical and does not use
the known timings that the core wants to use with the NAND chip, by
using local defined constants that have no special meaning from the
outside world.
Simplify the way all of this is computed and use the NAND core's SDR
timings.
Integrity of the reads/writes has been checked with nandbiterrs, speed
improvements with flash_speed on a Freescale i.MX6 DualLite/Solo SABRE
Automotive Board. Measures are below, variations of less than 150kiB/s
between tests are common and then not significant. Speeds using mode 5
are the same, while speeds using mode 0 are quite improved (+40/50%
from non-optimal computation).
Forcing timings mode 0:
=======================
Before this patch:
------------------
eraseblock write speed is 2298 KiB/s
eraseblock read speed is 3636 KiB/s
page write speed is 2136 KiB/s
page read speed is 3316 KiB/s
2 page write speed is 2199 KiB/s
2 page read speed is 3468 KiB/s
After this patch:
-----------------
eraseblock write speed is 3232 KiB/s
eraseblock read speed is 5663 KiB/s
page write speed is 2915 KiB/s
page read speed is 4904 KiB/s
2 page write speed is 3084 KiB/s
2 page read speed is 5267 KiB/s
Forcing timings mode 5:
=======================
Before this patch:
------------------
eraseblock write speed is 4338 KiB/s
eraseblock read speed is 14883 KiB/s
page write speed is 3786 KiB/s
page read speed is 12800 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
After this patch:
-----------------
eraseblock write speed is 4309 KiB/s
eraseblock read speed is 14712 KiB/s
page write speed is 3764 KiB/s
page read speed is 12673 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Until now the GPMI driver had its own timings logic while the core
already handles that and request the NAND controller drivers to support
the ->setup_data_interface() hook. Implement that hook by reusing the
already existing function. No real glue is necessary between core timing
delays and GPMI registers because the driver already translates the
ONFI timing modes into register values.
Make use of the core's tREA, tRLOH and tRHOH values that allow computing
more precise timings for mode [0-3] and get significantly better values
(+20% with an i.MX6 Sabre Auto board). Otherwise use the existing logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that hold all needed
ONFI parameters, remove the ONFI page from the nand_chip structure by
just allocating it during the identification phase and removing it right
after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that can held
generic parameters, remove the JEDEC page from the nand_chip structure
by just allocating it during the identification phase and removing it
right after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The MX30LF2G18AC chip declares in its parameter page supporting
SET/GET_FEATURES but when it comes to timings, experience shows that it
is not the case.
Unflag this feature for this particular chip in the nand_parameters
structure to avoid unnecessary errors and downturns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If SET/GET_FEATURES is available (from the parameter page), use a
bitmap to declare what feature is actually supported.
Initialize the bitmap in the core to support timing changes (only
feature used by the core), also add support for Micron specific features
used in Micron initialization code (in the init routine).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
ONFI-related parameters that will be used outside from the
identification function are stored in a separate onfi_parameters
structure embedded in nand_parameters, this small structure that
already hold generic parameters.
For now, the onfi_parameters structure is allocated statically. However,
after some deep rework in the NAND framework, it will be possible to do
dynamic allocations from the NAND identification phase, and this
strcuture will then be dynamically allocated when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
To prepare to the removal of such huge structure, a small NAND parameter
structure is allocated statically and contains only very few members
that are generic to all chips and actually used elsewhere in the code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
After a nand_reset_data_interface(), both the NAND chip and the NAND
controller use timing mode 0. The previously defined data interface for
this chip has been saved and is supposed to be restored after that.
However, if the saved data interface also refers to timing mode 0, there
is no need to re-apply them again.
Also, as nand_setup_data_interface() uses ->set/get_features(), it could
lead to issues when doing the reset at probe time as the parameter page
is not available yet to know if these functions are supported or not.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Choosing ONFI timings when ->set/get_features() calls are supported
by the NAND chip is a matter of reading the chip's ONFI parameter page
and telling the chip the chosen mode (between all of the supported ones)
with ->set_feature().
Add a check on whether the chip "acked" the timing mode or not.
This can be a problem for NAND chips that do not follow entirely the
ONFI specification. These chips actually support other modes than
"mode 0", but either:
1/ do not update the timing mode register once a timing mode has been
selected.
or
2/ do not support the TIMING_MODE featured and thus do not require users
to change the timing mode at all.
These issues will be addressed in another patch that will add the
feature to overwrite NAND chips features within the parameter page, from
the NAND chip driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
After a ->set_features(TIMINGS), the chip is supposed to be working at a
new speed. In order for all the transactions to be perperly handled, the
NAND controller should also be configured to this same speed. Calling
->setup_data_interface() is not enough and the chip should be
de-asserted/re-asserted through calls to ->select_chip().
Prepare the next change in nand_setup_data_interface() where timings
will be checked after being applied. Because assertions of the CS pin
will be needed from within this function, move the calls to
->select_chip() inside nand_setup_data_interface() for later
consistency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
All the calls to the chip's hooks ->get/set_features() go through
the core's wrappers nand_get/set_features() that already do the
necessary checks about feature support. Remove these
checks from the mxc's functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Usually, the source of the error when setting/getting features does not
matter (if the controller does not support sending the command or if
the chip does not support the operation).
When it comes to timings, if the controller fails it is an error while
if the chip does not support the operation, it can be silently supposed
that it already works with the maximum supported timings.
Introduce some logic in nand_setup_data_interface() to handle that
difference.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare the fact that some features managed by GET/SET_FEATURES could be
overloaded by vendor code. To handle this logic, use new wrappers
instead of directly call the ->get/set_features() hooks.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
SET/GET FEATURES are flagged ONFI-compliant because of their name. This
is not accurate as non-ONFI NAND chips support it and use it.
Rename the hooks and helpers to remove the "onfi" prefix.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare future work on the ->onfi_get/set_features() hooks by renaming
the core's implementation as 'default' ones.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Files have been moved in the NAND subsystem to reflect the different
flavors of NAND devices.
Raw/Parallel NAND devices have been moved to a "raw" subdirectory to
make the difference with OneNAND and SPI NAND for instance. So adjust
the Kconfig entry to clarify things.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The blackfin architecture is getting removed, so this driver has
become obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
With the move to ->exec_op() the driver should now support ONFI
SET/GET_FEATURES commands.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Now that the driver is using ->exec_op(), remove the old
hooks.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This reworks the driver to make use of ->exec_op() callback. The
command sequencer of the VF610 NFC aligns well with the new ops
interface.
The operations are translated to a NFC command code while filling
the necessary registers. Instead of using the special status and
read ID command codes (which require to read status/ID from
special registers instead of the regular data area) the driver
now now uses the main data buffer for all commands. This
simplifies the driver as no special casing is needed.
For control data (status byte, id bytes and parameter page) the
driver needs to reverse byte order for little endian CPUs since
the controller seems to store the bytes in big endian order in
the data buffer.
The current state seems to pass MTD tests on a Colibri VF61.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
->fail_addr and ->addr can be updated no matter the result of
parent->_erase(), we just need to remove the code doing the same thing
in mtd_erase_callback() to avoid adjusting those fields twice.
Note that this can be done because all MTD users have been converted to
not pass an erase_info->callback() and are thus only taking the
->addr_fail and ->addr fields into account after part_erase() has
returned.
While we're at it, get rid of the erase_info->mtd field which was only
needed to let mtd_erase_callback() get the partition device back.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
This file can not be built independently any more. We would have to
bring in more to resolve mtd_to_nand(mtd)->ecc.size, for example.
It is difficult to notice a breakage since nobody compiles this mode.
It is not worth fixing or maintaining in my opinion. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Using pr_<loglevel>() is more concise than printk(KERN_<LOGLEVEL>).
Replace printks having a log level with the appropriate pr_*() macros.
Define pr_fmt() and remove other additional macros from the replaced
printks.
Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Move onenand code base to the drivers/mtd/nand directory in the hope
that someday someone will patch it to use the generic NAND helpers.
If it never happens, at least we'll have all NAND related support in a
single directory and not spread over the drivers/mtd/ directory.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
- minor changes for property API
- clock API fix for ULPI driver warning
It exceptionally contains a merge from the mtd tree from Boris
to prevent any merge conflicts in the PXA tree.
-----BEGIN PGP SIGNATURE-----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=/vgG
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux into next/soc
Pull "This is the pxa changes for v4.17 cycle" from Robert Jarzmik:
- minor changes for property API
- clock API fix for ULPI driver warning
It exceptionally contains a merge from the mtd tree from Boris
to prevent any merge conflicts in the PXA tree.
* tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux:
ARM: pxa/raumfeld: use PROPERTY_ENTRY_U32() directly
ARM: pxa: ulpi: fix ulpi timeout and slowpath warn
ARM: pxa: cm-x300: remove inline directive
ARM: pxa: fix static checker warning in pxa3xx-ulpi
MAINTAINERS: remove entry for deleted pxa3xx_nand driver
arm: dts: pxa: use reworked NAND controller driver
dt-bindings: mtd: remove pxa3xx NAND controller documentation
mtd: nand: remove useless fields from pxa3xx NAND platform data
mtd: nand: remove deprecated pxa3xx_nand driver
mtd: nand: use Marvell reworked NAND controller driver with all platforms
The "enable arbiter" bit is available only for pxa3xx based platforms
but it was experimentally shown that even if this bit is reserved,
some Marvell platforms (64-bit) actually need it to be set. The driver
always set this bit regardless of this property, which is harmless.
Then this property is not needed.
The "num_cs" field is always 1 and for a good reason, the old driver
(pxa3xx_nand.c) could only handle one. The new driver that replaces it
(marvell_nand.c) can handle more, but better use device tree for such
description. As there is only one available chip select, there is no
need for an array of partitions neither an array of partition numbers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
All board files and defconfig files have been moved to use the new
marvell_nand driver instead of pxa3xx_nand, so we can safely remove this
file now. People should use the new driver which is supposed to behave
exactly like the old one.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Remove the deprecated ->cmd_ctrl() implementation to use ->exec_op() in
the fsmc_nand driver.
Implement the ->select_chip() hook to avoid having to support the hack
from the core that send a NAND_CMD_NONE with NAND_NCE to signal a
deassertion of nCE.
Also get rid of the last references to ->IO_ADDR_[R|W] that are not used
anymore.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Remove the use of IO_ADDR_[R|W] in the fsmc_nand driver. Instead, use a
pointer to the control registers to avoid doing several arithmetic
operations (including a multiplication) each time a control register is
read or written.
All references to IO_ADDR_[R|W] are not entirely removed from the driver
as, at this time, these values are needed by the NAND core in the
default ->read/write_byte/word() hooks. These references will be
entirely removed when switching to ->exec_op(), that does not make use
of these hooks anymore.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add an intermediate layer to abstract NAND device interface so that
some logic can be shared between SPI NANDs, parallel/raw NANDs,
OneNANDs, ...
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
As part of the process of sharing more code between different NAND
based devices, we need to move all raw NAND related code to the raw/
subdirectory.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some drivers have been derived from others which have then been removed
from the source tree. When this is the case, add mention the copyright
of the source file(s) they've been derived from.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
A lot of NAND drivers have been derived from other old NAND drivers
which have since then been removed from the Linux tree. When this is
the case, specify when the file the header is referring to has been
removed so that people can find the original implementation more
easily.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Last known location of toto.c was drivers/mtd/nand/toto.c. Fix the
path so that one can use git log to find when the driver was deleted
and possibly checkout the source code.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some NAND drivers are derived from other NAND drivers and state it in
their license header. Using full path to point to other driver files
sitting in the same directory is not such a good idea, since the NAND
drivers might be moved to a different directory at some point, and we
don't to patch all license/copyright headers everytime this happen.
The only exception where we keep full path is when the referred source
files no longer exist in the tree.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some files add a comment giving the path of the file inside the Linux
tree, which is pretty useless since the reader had to find the file to
open it.
Getting rid of these comments will also allow us to easily move these
files around when needed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch enables support to read the ECC strength and size from the
NAND flash using Toshiba Memory SLC NAND extended-ID. This patch is
based on the information of the 6th ID byte of the Toshiba Memory SLC
NAND.
Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
vf610_nfc_probe() misses error handling of mtd_device_register().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Use clearer error labels as Boris Brezillon suggested.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Calling of_node_put() in vf610_nfc_probe() is wrong because nothing in
this code retains a reference to the DT node.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The function count_written_bits has been replaced by the generic
nand_check_erased_ecc_chunk() function with commit 48c25cf441
("mtd: nand: vf610_nfc: use nand_check_erased_ecc_chunk() helper").
Remove the unused function.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
First generation of Marvell NAND flash controllers (eg. embedded in PXA
boards) did not make use of the NAND core hook ->setup_data_interface()
to setup controller timings. Add support for it.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Since we now have our own read_page/write_page functions
mxc_nand_command() will no longer be called with NAND_CMD_READ0,
NAND_CMD_READOOB, NAND_CMD_SEQIN and NAND_CMD_PAGEPROG. Remove
the code handling these commands.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Since we have our own read_page/write_page functions correct_data and
calculate are no longer needed. Remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Now that we have our own read_page function add a write_page function
for consistency aswell. This can be a lot easier than the generic
function since we do not have to iterate over subpages but can write
the whole page at once. Also add write_page_raw and write_oob for
proper raw and oob write support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The v1 controller code has several flaws:
- We do not forward the number of corrected bitflips to the upper layers
- For 2k page NAND chips only the status results from the fourth subpage
read are evaluated, so ECC failures in the other subpages remain
uncovered
- When there are uncorrectable errors we have to increase the statistics
counter, but still have to return successfully. Currently we return
an error
This patch fixes this by introducing a v1 specific read_page function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently nand_read_page_hwecc() from nand_base calls
mxc_nand_correct_data_v2_v3() for each subpage, but in this function we
return the corrected/failed results for the whole page instead
of a single subpage. On a 2k page size Nand this leads to results which
are 4 times too high.
The whole ecc.calculate/ecc.correct mechanism used by
nand_read_page_hwecc() is not suitable for devices which correct the
data in hardware, so fix this by using a driver specific read_page
function which does the right thing. Also add read_page_raw and read_oob
For proper raw and oob read support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
With following patches we will have to copy the spare data to/from
other buffers, so add the buffer as argument to copy_spare().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
For proper raw read/write support need to be able to control the
hardware ECC engine. Add a function to enable/disable it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
We'll call copy_spare() and mxc_do_addr_cycle() from another place
during the next patches, so move functions up to avoid forward
declarations.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
With commit 3cf32d1802 ("mtd: nand: vf610: switch to
mtd_ooblayout_ops") the driver started to use the NAND cores
default large page ooblayout. However, shortly after commit
6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
changed the default layout to the old hamming layout, which is
not what vf610_nfc is using. Specify the default large page
layout explicitly.
Fixes: 6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This pull requests contains a consolidation of the generic no-IOMMU code,
a well as the glue code for swiotlb. All the code is based on the x86
implementation with hooks to allow all architectures that aren't cache
coherent to use it. The x86 conversion itself has been deferred because
the x86 maintainers were a little busy in the last months.
-----BEGIN PGP SIGNATURE-----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=Nrl9
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping
Pull dma mapping updates from Christoph Hellwig:
"Except for a runtime warning fix from Christian this is all about
consolidation of the generic no-IOMMU code, a well as the glue code
for swiotlb.
All the code is based on the x86 implementation with hooks to allow
all architectures that aren't cache coherent to use it.
The x86 conversion itself has been deferred because the x86
maintainers were a little busy in the last months"
* tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping: (57 commits)
MAINTAINERS: add the iommu list for swiotlb and xen-swiotlb
arm64: use swiotlb_alloc and swiotlb_free
arm64: replace ZONE_DMA with ZONE_DMA32
mips: use swiotlb_{alloc,free}
mips/netlogic: remove swiotlb support
tile: use generic swiotlb_ops
tile: replace ZONE_DMA with ZONE_DMA32
unicore32: use generic swiotlb_ops
ia64: remove an ifdef around the content of pci-dma.c
ia64: clean up swiotlb support
ia64: use generic swiotlb_ops
ia64: replace ZONE_DMA with ZONE_DMA32
swiotlb: remove various exports
swiotlb: refactor coherent buffer allocation
swiotlb: refactor coherent buffer freeing
swiotlb: wire up ->dma_supported in swiotlb_dma_ops
swiotlb: add common swiotlb_map_ops
swiotlb: rename swiotlb_free to swiotlb_exit
x86: rename swiotlb_dma_ops
powerpc: rename swiotlb_dma_ops
...
Core changes:
* Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
* Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
Driver changes:
* CFI: use macros instead of inline functions to limit stack
usage and make KASAN happy
NAND changes:
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
SPI NOR changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----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=Mxo2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD core changes:
- Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
- Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
MTD driver changes:
- CFI: use macros instead of inline functions to limit stack usage
and make KASAN happy
NAND core changes:
- Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
- Introduce the ->exec_op() infrastructure
- Rework NAND buffers handling
- Fix ECC requirements for K9F4G08U0D
- Fix nand_do_read_oob() to return the number of bitflips
- Mark K9F1G08U0E as not supporting subpage writes
NAND driver changes:
- MTK: Rework the driver to support new IP versions
- OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
fix DT support
- Marvell: Add a new driver to replace the pxa3xx one
SPI NOR core changes:
- Add support to new ISSI and Cypress/Spansion memory parts.
- Fix support of Micron memories by checking error bits in the FSR.
- Fix update of block-protection bits by reading back the SR.
- Restore the internal state of the SPI flash memory when removing
the device.
SPI NOR driver changes:
- Maintenance for Freescale, Intel and Metiatek drivers.
- Add support of the direct access mode for the Cadence QSPI
controller"
* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
mtd: nand: sunxi: Fix ECC strength choice
mtd: nand: gpmi: Fix subpage reads
mtd: nand: Fix build issues due to an anonymous union
mtd: nand: marvell: Fix missing memory allocation modifier
mtd: nand: marvell: remove redundant variable 'oob_len'
mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
mtd: Remove duplicate checks on mtd_oob_ops parameter
mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
mtd: mtdpart: Make ECC stat handling consistent
mtd: onenand: omap2: print resource using %pR format string
mtd: mtk-nor: modify functions' name more generally
mtd: onenand: samsung: remove incorrect __iomem annotation
MAINTAINERS: Add entry for Marvell NAND controller driver
ARM: OMAP2+: Remove gpmc-onenand
mtd: onenand: omap2: Configure driver from DT
mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
mtd: onenand: omap2: Convert to use dmaengine for memcpy
mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
...
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
-----BEGIN PGP SIGNATURE-----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=TXIU
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.16' of git://git.infradead.org/linux-mtd into mtd/next
Pull NAND changes from Boris Brezillon:
"
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
"
When the requested ECC strength does not exactly match the strengths
supported by the ECC engine, the driver is selecting the closest
strength meeting the 'selected_strength > requested_strength'
constraint. Fix the fact that, in this particular case, ecc->strength
value was not updated to match the 'selected_strength'.
For instance, one can encounter this issue when no ECC requirement is
filled in the device tree while the NAND chip minimum requirement is not
a strength/step_size combo natively supported by the ECC engine.
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Cc: <stable@vger.kernel.org>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 25f815f66a ("mtd: nand: force drivers to explicitly send
READ/PROG commands") added a call to nand_read_page_op() in
gpmi_ecc_read_page(), which means this function now sends a READ0
command and place the data pointer at the beginning of the page. This
logic is breaking gpmi_ecc_read_subpage() which was calling
gpmi_ecc_read_page() and expected it to only retrieve the data without
sending the READ0 command.
Create a gpmi_ecc_read_page_data() helper which only does the data
retrieval and ECC correction steps and implement gpmi_ecc_read_page()
as a wrapper that calls nand_read_page_op()+gpmi_ecc_read_page_data().
This way, gpmi_ecc_read_subpage() can call gpmi_ecc_read_page_data()
which restores the logic we had before commit 25f815f66a ("mtd: nand:
force drivers to explicitly send READ/PROG commands").
Fixes: 25f815f66a ("mtd: nand: force drivers to explicitly send READ/PROG commands")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Han Xu <han.xu@nxp.com>
GCC-4.4.4 raises errors when assigning a parameter in an anonymous
union, leading to this kind of failure:
drivers/mtd/nand/marvell_nand.c:1936:
warning: missing braces around initializer
warning: (near initialization for '(anonymous)[1].<anonymous>')
error: unknown field 'data' specified in initializer
error: unknown field 'addr' specified in initializer
Work around the situation by naming these unions.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The function marvell_nfc_init_dma() allocates a DMA buffer without the
GFP_KERNEL modifier, that triggers this warning:
"marvell_nfc_init_dma() error: no modifiers for allocation."
Fix this by using (GFP_KERNEL | GFP_DMA) instead of only GFP_DMA as the
probe happens in non-interrupt context.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Variable oob_len is assigned and never read, hence it is redundant and
can be removed.
Cleans up clang warnings:
drivers/mtd/nand/marvell_nand.c:1356:6: warning: Value stored to 'oob_len'
during its initialization is never read
drivers/mtd/nand/marvell_nand.c:1369:4: warning: Value stored to 'oob_len'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Trivial fix to spelling mistakes in dev_err error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some of the check done in custom ->_read/write_oob() implementation are
already done by the core (in mtd_check_oob_ops()).
Suggested-by: Peter Pan <peterpansjtu@gmail.com>
[Remove redundant checks done in mtdpart.c]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Some MTD sublayers/drivers are implementing ->_read/write_oob() and
provide dummy wrappers for their ->_read/write() implementations.
Let the core handle this case instead of duplicating the logic.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Add marvell_nand driver which aims at replacing the existing pxa3xx_nand
driver.
The new driver intends to be easier to understand and follows the brand
new NAND framework rules by implementing hooks for every pattern the
controller might support and referencing them inside a parser object
that will be given to the core at each ->exec_op() call.
Raw accessors are implemented, useful to test/debug memory/filesystem
corruptions. Userspace binaries contained in the mtd-utils package may
now be used and their output trusted.
Most of the DT nodes using the old driver kept non-optimal timings from
the bootloader (even if there was some mechanisms to derive them if the
chip was ONFI compliant). The new default is to implement
->setup_data_interface() and follow the core's decision regarding the
chip.
Thanks to the improved timings, implementation of ONFI mode 5 support
(with EDO managed by adding a delay on data sampling), merging the
commands together and optimizing writes in the command registers, the
new driver may achieve faster throughputs in both directions.
Measurements show an improvement of about +23% read throughput and +24%
write throughput. These measurements have been done with an
Armada-385-DB-AP (4kiB NAND pages forced in 4-bit strength BCH ECC
correction) using the userspace tool 'flash_speed' from the MTD test
suite.
Besides these important topics, the new driver addresses several
unsolved known issues in the old driver which:
- did not work with ECC soft neither with ECC none ;
- relied on naked read/write (which is unchanged) while the NFCv1
embedded in the pxa3xx platforms do not implement it, so several
NAND commands did not actually ever work without any notice (like
reading the ONFI PARAM_PAGE or SET/GET_FEATURES) ;
- wrote the OOB data correctly, but was not able to read it correctly
past the first OOB data chunk ;
- did not retrieve ECC bytes ;
- used device tree bindings that did not allow more than one NAND chip,
and did not allow to choose the correct chip select if not
incrementing from 0. Plus, the Ready/Busy line used had to be 0.
Old device tree bindings are still supported but deprecated. A more
hierarchical view has to be used to keep the controller and the NAND
chip structures clearly separated both inside the device tree and also
in the driver code.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Starting from commit 041e4575f0 ("mtd: nand: handle ECC errors in
OOB"), nand_do_read_oob() (from the NAND core) did return 0 or a
negative error, and the MTD layer expected it.
However, the trend for the NAND layer is now to return an error or a
positive number of bitflips. Deciding which status to return to the user
belongs to the MTD layer.
Commit e47f68587b ("mtd: check for max_bitflips in mtd_read_oob()")
brought this logic to the mtd_read_oob() function while the return value
coming from nand_do_read_oob() (called by the ->_read_oob() hook) was
left unchanged.
Fixes: e47f68587b ("mtd: check for max_bitflips in mtd_read_oob()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
phys_to_dma, dma_to_phys and dma_capable are helpers published by
architecture code for use of swiotlb and xen-swiotlb only. Drivers are
not supposed to use these directly, but use the DMA API instead.
Move these to a new asm/dma-direct.h helper, included by a
linux/dma-direct.h wrapper that provides the default linear mapping
unless the architecture wants to override it.
In the MIPS case the existing dma-coherent.h is reused for now as
untangling it will take a bit of work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Samsung E-die SLC NAND manufactured using 21nm process (K9F1G08U0E)
does not support partial page programming, so disable subpage writes
for it. Manufacturing process is stored in lowest two bits of 5th ID
byte.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Brcm nand controller prefetch feature needs to be disabled
by default. Enabling affects performance on random reads as
well as dma reads.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Cc: <stable@vger.kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In the current driver, OOB bytes are accessed in raw mode, and when a
page access is done with NDCR_SPARE_EN set and NDCR_ECC_EN cleared, the
driver must read the whole spare area (64 bytes in case of a 2k page,
16 bytes for a 512 page). The driver was only reading the free OOB
bytes, which was leaving some unread data in the FIFO and was somehow
leading to a timeout.
We could patch the driver to read ->spare_size + ->ecc_size instead of
just ->spare_size when READOOB is requested, but we'd better make
in-band and OOB accesses consistent.
Since the driver is always accessing in-band data in non-raw mode (with
the ECC engine enabled), we should also access OOB data in this mode.
That's particularly useful when using the BCH engine because in this
mode the free OOB bytes are also ECC protected.
Fixes: 43bcfd2bb2 ("mtd: nand: pxa3xx: Add driver-specific ECC BCH support")
Cc: stable@vger.kernel.org
Reported-by: Sean Nyekjær <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
devm_kasprintf() may fail, so we should better add a NULL check
and propagate an error on failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
devm_kasprintf() may fail, so we should better add a NULL check
and propagate an error on failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Give an unfinished comment a meaning.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Introduce a new interface to instruct NAND controllers to send specific
NAND operations. The new interface takes the form of a single method
called ->exec_op(). This method is designed to replace ->cmd_ctrl(),
->cmdfunc() and ->read/write_byte/word/buf() hooks.
->exec_op() is passed a set of instructions describing the operation
to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY)
and delay. The delay is here to help simple controllers wait enough
time between each instruction, advanced controllers with integrated
timings control can ignore these delays.
Controllers that natively support complex operations (operations
formed of several instructions) can use the NAND op parser
infrastructure. This infrastructure allows controller drivers to
describe the sequence of instructions they support (called
nand_op_pattern) and a hook for each of these supported sequences. The
core then tries to find the best match for a given NAND operation, and
calls the associated hook.
Various other helpers are also added to ease NAND controller drivers
writing.
This new interface should ease support of vendor specific operations
in that NAND manufacturer drivers now have a way to check if the
controller they are connected to supports a specific operation, and
complain or refuse to probe the NAND chip when that's not the case.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A negative return value of brcmstb_nand_verify_erased_page() indicates a
real bitflip error of an erased page, and other return values (>= 0) show
the corrected bitflip number. Zero return value means no bitflip, but the
current driver code treats it as an error, and eventually leads to
falsely reported ECC error.
Fixes: 02b88eea9f ("mtd: brcmnand: Add check for erased page bitflip")
Signed-off-by: Albert Hsieh <wen.hsieh@broadcom.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
When erased subpages are read then the BCH decoder returns STATUS_ERASED
if they are all empty, or STATUS_UNCORRECTABLE if there are bitflips.
When there are bitflips, we have to set these bits again to show the
upper layers a completely erased page. When a bitflip happens in the
exact byte where the bad block marker is, then this byte is swapped
with another byte in block_mark_swapping(). The correction code then
detects a bitflip in another subpage and no longer corrects the bitflip
where it really happens.
Correct this behaviour by calling block_mark_swapping() after the
bitflips have been corrected.
In our case UBIFS failed with this bug because it expects erased
pages to be really empty:
UBIFS error (pid 187): ubifs_scan: corrupt empty space at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: corruption at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: first 8192 bytes from LEB 36:118735
UBIFS error (pid 187): ubifs_scan: LEB 36 scanning failed
UBIFS error (pid 187): do_commit: commit failed, error -117
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Samsung NAND chip K9F4G08U0D minimum ECC strength requirement is 1 bit
per 512 bytes. As the chip is not ONFI nor JEDEC and because of the lack
of these values, boards using it fail to probe the NAND controller
driver. Fix this by setting up the default values.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The only users of the ecc->{calc,code}_buf buffers are NAND controller
drivers implementing ecc->calculate() and/or ecc->correct(). Since the
->oobsize can be non-negligle, especially on modern NAND devices, we'd
better allocate it only when it is actually required.
Make ecc->{calc,code}_buf allocation dependent on the presence of
ecc->calculate() or ecc->correct().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
ECC bytes are contiguous in the ->oob_poi buffer, which means we don't
have to copy them into ->code_buf (here used as a temporary buffer)
before passing them to the nand_check_erased_ecc_chunk() function.
This change will allow us to allocate ecc->{code,calc}_buf only when
ecc->calculate() or ecc->correct() is specified.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add tables to support MT7622 NAND flash controller.
Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
MT7622 uses an MTK's earlier NAND flash controller IP which support
different sector size, max spare size per sector and paraity bits...,
some register's offset and definition also been changed in the NAND
flash controller, this patch is the preparation to support MT7622
NAND flash controller.
MT7622 NFC and ECC engine are similar to MT2701's, except below
differences:
(1)MT7622 NFC's max sector size(ECC data size) is 512 bytes, and
MT2701's is 1024, and MT7622's max sector number is 8.
(2)The parity bit of MT7622 is 13, MT2701 is 14.
(3)MT7622 ECC supports less ECC strength, max to 16 bit ecc strength.
(4)MT7622 supports less spare size per sector, max spare size per
sector is 28 bytes.
(5)Some register's offset are different, include ECC_ENCIRQ_EN,
ECC_ENCIRQ_STA, ECC_DECDONE, ECC_DECIRQ_EN and ECC_DECIRQ_STA.
(6)ENC_MODE of ECC_ENCCNFG register is moved from bit 5-6 to bit 4-5.
Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use macros from <linux/kernel.h> to make the code readable.
The compiler warning will be kept suppressed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
struct nand_buffers is malloc'ed in nand_scan_tail() just for
containing three pointers. Squash this struct into nand_chip.
Move and rename as follows:
chip->buffers->ecccalc -> chip->ecc.calc_buf
chip->buffers->ecccode -> chip->ecc.code_buf
chip->buffers->databuf -> chip->data_buf
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The last/only user of NAND_OWN_BUFFERS (cafe_nand.c) has been reworked.
This flag is no longer needed.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver is the last/only user of NAND_OWN_BUFFERS. Boris suggested
to remove this flag.
Taking a closer look at this driver, it calls dma_alloc_coherent() for
the concatenated area for the DMA bounce buffer + struct nand_buffers,
but the latter does not need to be DMA-coherent; cafe_{write,read}_buf
simply do memcpy() between buffers when usedma==1.
Let's do dma_alloc_coherent() for the DMA bounce buffer in the front,
and leave the nand_buffers allocation to nand_scan_tail(), then rip off
NAND_OWN_BUFFERS.
The magic number, 2112, is still mysterious (hard-coded writesize +
oobsize ?), but this is not our main interest. I am keeping it.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Right now, the chip->data_interface field is populated in
nand_scan_tail(), so after the whole NAND detection has taken place.
This is fine because these timings are not yet used by the core so
early in the probe process, but the situation is about to change with
the introduction of ->exec_op().
Also, by convention, nand_scan_ident() is not supposed to allocate
resources, only nand_scan_tail() can, so this prevent us from
allocating and initializing the data_interface object in
nand_scan_ident().
In order to solve this problem, directly embed a data_interface object
in nand_chip so that we don't have to allocate it, and initialize it to
ONFI SDR mode 0 at the very beginning of nand_scan_ident().
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core currently send the READ0 and SEQIN+PAGEPROG commands in
nand_do_read/write_ops(). This is inconsistent with
->read/write_oob[_raw]() hooks behavior which are expected to send
these commands.
There's already a flag (NAND_ECC_CUSTOM_PAGE_ACCESS) to inform the core
that a specific controller wants to send the READ/SEQIN+PAGEPROG
commands on its own, but it's an opt-in flag, and existing drivers are
unlikely to be updated to pass it.
Moreover, some controllers cannot dissociate the READ/PAGEPROG commands
from the associated data transfer and ECC engine activation, and
developers have to hack things in their ->cmdfunc() implementation to
handle such complex cases, or have to accept the perf penalty of sending
twice the same command.
To address this problem we are planning on adding a new interface which
is passed all information about a NAND operation (including the amount
of data to transfer) and replacing all calls to ->cmdfunc() to calls to
this new ->exec_op() hook. But, in order to do that, we need to have all
->cmdfunc() calls placed near their associated ->read/write_buf/byte()
calls.
Modify the core and relevant drivers to make NAND_ECC_CUSTOM_PAGE_ACCESS
the default case, and remove this flag.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: tested, fixed and rebased on nand/next]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is part of the process of removing direct calls to ->cmdfunc()
outside of the core in order to introduce a better interface to execute
NAND operations.
Here we provide several helpers and make use of them to remove all
direct calls to ->cmdfunc(). This way, we can easily modify those
helpers to make use of the new ->exec_op() interface when available.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: rebased and fixed some conflicts]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Avoid using specific defined values for checking returned status of the
->erase() hook. Instead, use usual negative error values on failure,
zero otherwise.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The "dma_buf" is not used for a DMA bounce buffer, but for arranging
the transferred data for the syndrome page layout. In fact, it is
used in the PIO mode as well, so "dma_buf" is a misleading name.
Rename it to "tmp_buf".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
'extern' is not necessary for function declarations.
scripts/checkpatch.pl with --strict option reports the following:
CHECK: extern prototypes should be avoided in .h files
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Bufnum mask is used to calculate page position in the internal SRAM.
As IFC version 2.0.0 has 16KB of internal SRAM as compared to older
versions which had 8KB. Hence bufnum mask needs to be updated.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/mtd/nand/denali_pci.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The GPMI nand Kconfig help texts mentions that the GPMI nand driver
might conflict with SD cards. The only conflict there might really
be is that both controllers use the same pins, but this is resolved
by the pincontroller setup in the device tree. In any way the GPMI
driver can safely be enabled, the text is just wrong. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Setting read-retry parameters has no impact on the R/B pin, so waiting
for the chip to be ready is useless.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some drivers (like nand_hynix.c) call ->cmdfunc() with NAND_CMD_NONE
and a column address and expect the controller to only send address
cycles. Right now, the default ->cmdfunc() implementations provided by
the core do not filter out the command cycle in this case and forwards
the request to the controller driver through the ->cmd_ctrl() method.
The thing is, NAND controller drivers can get this wrong and send a
command cycle with a NAND_CMD_NONE opcode and since NAND_CMD_NONE is
-1, and the command field is usually casted to an u8, we end up sending
the 0xFF command which is actually a RESET operation.
Add conditions in nand_command[_lp]() functions to sending the initial
command cycle when command == NAND_CMD_NONE.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Make use of the swap macro and remove unnecessary variables swap.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Previously, we only select chips and then send reset command to a NAND
device during resuming nand driver. There is a lack of deselecting chips.
It is advised to reset and initialize a NAND device using nand_reset().
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
General changes:
* Unconfuse get_unmapped_area and point/unpoint driver methods
* New partition parser: sharpslpart
* Kill GENERIC_IO
* Various fixes
NAND changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
SPI-NOR changes:
* Introduce system power management support
* New mechanism to select the proper .quad_enable() hook by JEDEC ID,
when needed, instead of only by manufacturer ID
* Add support to new memory parts from Gigadevice, Winbond, Macronix and
Everspin
* Maintainance for Cadence, Intel, Mediatek and STM32 drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wVm7
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd
Pull MTD updates from Richard Weinberger:
"General changes:
- Unconfuse get_unmapped_area and point/unpoint driver methods
- New partition parser: sharpslpart
- Kill GENERIC_IO
- Various fixes
NAND changes:
- Add a flag to mark NANDs that require 3 address cycles to encode a
page address
- Set a default ECC/free layout when NAND_ECC_NONE is requested
- Fix a bug in panic_nand_write()
- Another batch of cleanups for the denali driver
- Fix PM support in the atmel driver
- Remove support for platform data in the omap driver
- Fix subpage write in the omap driver
- Fix irq handling in the mtk driver
- Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
- Change log level of ECC error messages in the mxc driver
- Patch the pxa3xx driver to support Armada 8k platforms
- Add BAM DMA support to the qcom driver
- Convert gpio-nand to the GPIO desc API
- Fix ECC handling in the mt29f driver
SPI-NOR changes:
- Introduce system power management support
- New mechanism to select the proper .quad_enable() hook by JEDEC
ID, when needed, instead of only by manufacturer ID
- Add support to new memory parts from Gigadevice, Winbond, Macronix
and Everspin
- Maintainance for Cadence, Intel, Mediatek and STM32 drivers"
* tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
mtd: sharpslpart: Add sharpslpart partition parser
mtd: Add sanity checks in mtd_write/read_oob()
mtd: remove the get_unmapped_area method
mtd: implement mtd_get_unmapped_area() using the point method
mtd: chips/map_rom.c: implement point and unpoint methods
mtd: chips/map_ram.c: implement point and unpoint methods
mtd: mtdram: properly handle the phys argument in the point method
mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
mtd: slram: use memremap() instead of ioremap()
kconfig: kill off GENERIC_IO option
mtd: Fix C++ comment in include/linux/mtd/mtd.h
mtd: constify mtd_partition
mtd: plat-ram: Replace manual resource management by devm
mtd: nand: Fix writing mtdoops to nand flash.
mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
mtd: nand: mtk: fix infinite ECC decode IRQ issue
mtd: spi-nor: Add support for mr25h128
mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
mtd: spi-nor: enable 4B opcodes for mx66l51235l
...
Commit e8e3edb95c ("mtd: create per-device and module-scope debugfs
entries") tried to make MTD related debugfs stuff consistent across the
MTD framework by creating a root <debugfs>/mtd/ directory containing
one directory per MTD device.
The problem is that, by default, the MTD layer only registers the
master device if no partitions are defined for this master. This
behavior breaks all drivers that expect mtd->dbg.dfs_dir to be filled
correctly after calling mtd_device_register() in order to add their own
debugfs entries.
The only way we can force all MTD masters to be registered no matter if
they expose partitions or not is by enabling the
CONFIG_MTD_PARTITIONED_MASTER option.
In such situations, there's no other solution but to accept skipping
debugfs initialization when dbg.dfs_dir is invalid, and when this
happens, inform the user that he should consider enabling
CONFIG_MTD_PARTITIONED_MASTER.
Fixes: e8e3edb95c ("mtd: create per-device and module-scope debugfs entries")
Cc: <stable@vger.kernel.org>
Cc: Mario J. Rugiero <mrugiero@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
mtd_partition are not supposed to change at runtime.
Functions 'mtd_device_parse_register' working with const mtd_partition
provided by <linux/mtd/mtd.h>. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
Driver changes:
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
-----BEGIN PGP SIGNATURE-----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=iUhH
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.15' of git://git.infradead.org/l2-mtd
From Boris:
"
Core changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
Driver changes:
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
"
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mtdoops calls mtd_panic_write(), it eventually calls
panic_nand_write() in nand_base.c. In order to properly wait for the
nand chip to be ready in panic_nand_wait(), the chip must first be
selected.
When using the atmel nand flash controller, a panic would occur due to
a NULL pointer exception.
Fixes: 2af7c65399 ("mtd: Add panic_write for NAND flashes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
For MT2701 NAND Controller, there may generate infinite ECC decode IRQ
during long time burn test on some platforms. Once this issue occurred,
the ECC decode IRQ status cannot be cleared in the IRQ handler function,
and threads cannot be scheduled.
ECC HW generates decode IRQ each sector, so there will have more than one
decode IRQ if read one page of large page NAND.
Currently, ECC IRQ handle flow is that we will check whether it is decode
IRQ at first by reading the register ECC_DECIRQ_STA. This is a read-clear
type register. If this IRQ is decode IRQ, then the ECC IRQ signal will be
cleared at the same time.
Secondly, we will check whether all sectors are decoded by reading the
register ECC_DECDONE. This is because the current IRQ may be not dealed
in time, and the next sectors have been decoded before reading the
register ECC_DECIRQ_STA. Then, the next sectors's decode IRQs will not
be generated.
Thirdly, if all sectors are decoded by comparing with ecc->sectors, then we
will complete ecc->done, set ecc->sectors as 0, and disable ECC IRQ by
programming the register ECC_IRQ_REG(op) as 0. Otherwise, wait for the
next ECC IRQ.
But, there is a timing issue between step one and two. When we read the
reigster ECC_DECIRQ_STA, all sectors are decoded except the last sector,
and the ECC IRQ signal is cleared. But the last sector is decoded before
reading ECC_DECDONE, so the ECC IRQ signal is enabled again by ECC HW, and
it means we will receive one extra ECC IRQ later. In step three, we will
find that all sectors were decoded, then disable ECC IRQ and return.
When deal with the extra ECC IRQ, the ECC IRQ status cannot be cleared
anymore. That is because the register ECC_DECIRQ_STA can only be cleared
when the register ECC_IRQ_REG(op) is enabled. But actually we have
disabled ECC IRQ in the previous ECC IRQ handle. So, there will
keep receiving ECC decode IRQ.
Now, we read the register ECC_DECIRQ_STA once again before completing the
ecc done event. This ensures that there will be no extra ECC decode IRQ.
Also, remove writel(0, ecc->regs + ECC_IRQ_REG(op)) from irq handler,
because ECC IRQ is disabled in mtk_ecc_disable(). And clear ECC_DECIRQ_STA
in mtk_ecc_disable() in case there is a timeout to wait decode IRQ.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Cc: <stable@vger.kernel.org>
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There will get mtk ecc handler during mtk nand probe now.
If mtk ecc module is not initialized, then mtk nand probe will return
-EPROBE_DEFER, and retry later.
Change the compile sequence of mtk_nand.o and mtk_ecc.o, initialize mtk
ecc module before mtk nand module. This makes mtk nand module initialized
as soon as possible.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since v4.12, NAND subpage writes were causing a NULL pointer
dereference on OMAP platforms (omap2-nand) using OMAP_ECC_BCH4_CODE_HW,
OMAP_ECC_BCH8_CODE_HW and OMAP_ECC_BCH16_CODE_HW.
This is because for those ECC modes, omap_calculate_ecc_bch()
generates ECC bytes for the entire (multi-sector) page and this can
overflow the ECC buffer provided by nand_write_subpage_hwecc()
as it expects ecc.calculate() to return ECC bytes for just one sector.
However, the root cause of the problem is present since v3.9
but was not seen then as NAND buffers were being allocated
as one big chunk prior to commit 3deb9979c7 ("mtd: nand: allocate
aligned buffers if NAND_OWN_BUFFERS is unset").
Fix the issue by providing a OMAP optimized write_subpage()
implementation.
Fixes: 62116e5171 ("mtd: nand: omap2: Support for hardware BCH error correction.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When a struct device * is around use dev_dbg instead of pr_debug
to give the messages more context.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Having bad ECC is a normal case for NAND, do not spam log with the
message. Users like UBI will print a message anyway which is more
useful since it contains the PEB number that has bad ECC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
commit 67ce04bf27 ("mtd: nand: add OMAP2/OMAP3 NAND driver") assigned
pointer to omap_nand_info to the platform drvdata in probe function
just to be reasigned later to the pointer to mtd_info, which is
what remove function expects it to be. Remove useless assignment.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As driver is now configured using DT, omap_nand_platform_data structure
is no longer needed.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 6e532afaca ("mtd: nand: atmel: Add PM ops") started to use the
nand_reset() function which was not yet exported by the NAND framework
(because it was only used internally before that). Export this symbol
to avoid build errors when the driver is enabled as a module.
Fixes: 6e532afaca ("mtd: nand: atmel: Add PM ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Marvell recent SoCs like A7k/A8k do not boot with NAND flash
controller activated by default. Enabling the controller is a matter of
writing in a system controller register that may also be used for other
NAND related choices.
This change is needed to stay bootloader independent.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the of_device_get_match_data() helper instead of open coding.
While at it, make config const so the cast can be dropped.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The WE_2_RE register specifies the number of clock cycles inserted
between the rising edge of #WE and the falling edge of #RE.
The current setup_data_interface implementation takes care of tWHR,
but tCCS is missing. Wait for max(tCSS, tWHR) to meet the spec.
With setup_data_interface() properly programmed, the Denali NAND
controller can observe the timing, so NAND_WAIT_TCCS flag is unneeded.
Clarify this in the comment block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
More and more SoCs use the pxa3xx_nand driver for their controller but
the list of them was not updated. This patch add the last SoCs using the
driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
During backup mode, the contents of all registers will be cleared as the
SoC will be completely powered down. For a product that boots on NAND
Flash memory, the bootloader will obviously use the related controller
to read the Flash and correct any detected error in the memory, before
handling back control to the kernel's resuming entry point.
But it does not clean the NAND controller registers after use and on its
side the kernel driver expects the error locator to be powered down and
in a clean state. Add a resume hook for the PMECC error locator, and
reset its registers.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. Add the function for command descriptor preparation which will
be used only by BAM DMA and it will form the DMA descriptors
containing command elements
2. DMA_PREP_CMD flag should be used for forming command DMA
descriptors
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All the QPIC register read/write through BAM DMA requires
command descriptor which contains the array of command elements.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is exactly one board in the kernel that defines platform data
for the GPIO NAND driver.
Use the feature to provide a lookup table for the GPIOs in the board
file so we can convert the driver as a whole to just use GPIO
descriptors.
After this we can cut the use of <linux/of_gpio.h> and use the GPIO
descriptor management from <linux/gpio/consumer.h> alone to grab and use
the GPIOs used in the driver.
I also created a local struct device *dev in the probe() function
because I was getting annoyed with all the &pdev->dev dereferencing.
Cc: arm@kernel.org
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Frans Klaver <fransklaver@gmail.com>
Cc: Gerhard Sittig <gsi@denx.de>
Cc: Jamie Iles <jamie.iles@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jamie Iles <jamie.iles@oracle.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When calculating the size needed by struct atmel_pmecc_user *user,
the dmu and delta buffer sizes were forgotten.
This lead to a memory corruption (especially with a large ecc_strength).
Link: http://lkml.kernel.org/r/1506503157.3016.5.camel@gmail.com
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: stable@vger.kernel.org
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Pointed-at-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The previous commit added some hooks into struct denali_nand_info,
so here is one more for clean-up.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali NAND IP core decodes the lower 28 bits of the slave address
to get the control information; bit[27:26]=mode, bit[25:24]=bank, etc.
This means 256MB address range must be allocated for this IP. (Direct
Addressing)
For systems with address space limitation, the Denali IP provides an
optional module that translates the addressing - address and data are
latched by the registers in the translation module. (Indexed Addressing)
The addressing mode can be selected when the delivered RTL is configured,
and it can be read out from the FEATURES register.
Most of SoC vendors would choose Indexed Addressing to save the address
space, but Direct Addressing is possible as well, and it can be easily
supported by adding ->host_{read,write} hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ECC correction is properly enabled/disabled before the page
read/write. There is no need to set up this at the beginning of
the probe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
I used (uint64_t) cast to avoid "right shift count >= width of type"
warning. <linux/kernel.h> provides nice helpers to cater to it.
The code will be cleaner, and easier to understand.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver explains too much about what is apparent from the code.
Comments around basic APIs such as init_completion(), spin_lock_init(),
etc. seem unneeded lessons to kernel developers.
(With those comments dropped, denali_drv_init() is small enough,
so it has been merged into the probe function.)
Also, NAND driver developers should know the NAND init procedure, so
there is no need to explain nand_scan_ident/tail.
I removed FSF's address from the license blocks, and added simple
comments to struct members.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In several places in this driver, the register fields are retrieved
as follows:
val = reg & FOO_MASK;
Then, modified as follows:
reg &= ~FOO_MASK;
reg |= val;
This code relies on its shift is 0, which we will never know until
we check the definition of FOO_MASK. Use FIELD_PREP / FIELD_GET
where appropriate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All the register offsets and bitfield masks are defined in denali.h,
but the driver code ended up with additional crappy macros such as
MAKE_ECC_CORRECTION(), ECC_SECTOR(), etc.
The reason is apparent - accessing a register field requires mask and
shift pair. The denali.h only provides mask. However, defining both
is tedious.
<linux/bitfield.h> provides a convenient way to get register fields
only with a single shifted mask. Now use it.
While I am here, I shortened some macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This function has a local variable "irq_mask" and its value is
the same as denali->irq_mask. Clean up the code a little.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This helper just sets/clears a flag of DMA_ENABLE register (with
register read-back, I do not know why it is necessary).
Move the register write code to the caller, and remove the helper.
It works for me without the register read-back.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Include necessary headers explicitly without relying on indirect
header inclusion. Also, sort them alphabetically.
<linux/delay.h>, <linux/wait.h>, <linux/mutex.h> turned out bogus,
so removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All functions in this driver are prefixed with denali_
except detect_max_banks(). Rename it for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The setup_ecc_for_xfer() is only called from denali_data_xfer().
This helper is small enough, so squash it into the caller.
This looks cleaner to me.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The register TWO_ROW_ADDR_CYCLES specifies the number of row address
cycles of the device, but it is fixed to 0 in the driver init code
(i.e. always 3 row address cycles).
Reflect the result of nand_scan_ident() to the register setting
in order to support 2 row address cycle devices.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Several drivers check ->chipsize to see if the third row address cycle
is needed. Instead of embedding magic sizes such as 32MB, 128MB in
drivers, introduce a new flag NAND_ROW_ADDR_3 for clean-up. Since
nand_scan_ident() knows well about the device, it can handle this
properly. The flag is set if the row address bit width is greater
than 16.
Delete comments such as "One more address cycle for ..." because
intention is now clear enough from the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the core's large page OOB layout functions when not reserving any
space for ECC bytes in the OOB layout. Fix ->nand_ooblayout_ecc_lp()
to return -ERANGE instead of a zero length in this case.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This patch fix the following build warning:
drivers/mtd/nand/nand_base.c:2671:30: attention : variable ‘blockmask’ set but not used [-Wunused-but-set-variable]
Fixes: 0b4773fd16 ("mtd: nand: Drop unused cached programming support")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If 'clk_prepare_enable()' fails, we must 'put' the corresponding clock.
Fixes: 4d26f012ab ("mtd: nand: lpc32xx_mlc: Handle return value of clk_prepare_enable.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Pull more set_fs removal from Al Viro:
"Christoph's 'use kernel_read and friends rather than open-coding
set_fs()' series"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: unexport vfs_readv and vfs_writev
fs: unexport vfs_read and vfs_write
fs: unexport __vfs_read/__vfs_write
lustre: switch to kernel_write
gadget/f_mass_storage: stop messing with the address limit
mconsole: switch to kernel_read
btrfs: switch write_buf to kernel_write
net/9p: switch p9_fd_read to kernel_write
mm/nommu: switch do_mmap_private to kernel_read
serial2002: switch serial2002_tty_write to kernel_{read/write}
fs: make the buf argument to __kernel_write a void pointer
fs: fix kernel_write prototype
fs: fix kernel_read prototype
fs: move kernel_read to fs/read_write.c
fs: move kernel_write to fs/read_write.c
autofs4: switch autofs4_write to __kernel_write
ashmem: switch to ->read_iter
General updates:
* Constify pci_device_id in various drivers
* Constify device_type
* Remove pad control code from the Gemini driver
* Use %pOF to print OF node full_name
* Various fixes in the physmap_of driver
* Remove unused vars in mtdswap
* Check devm_kzalloc() return value in the spear_smi driver
* Check clk_prepare_enable() return code in the st_spi_fsm driver
* Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
* add support to the JEDEC JESD216B specification (SFDP tables).
* add support to the Intel Denverton SPI flash controller.
* fix error recovery for Spansion/Cypress SPI NOR memories.
* fix 4-byte address management for the Aspeed SPI controller.
* add support to some Microchip SST26 memory parts
* remove unneeded pinctrl header Write a message for tag:
-----BEGIN PGP SIGNATURE-----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=UgCd
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"General updates:
- Constify pci_device_id in various drivers
- Constify device_type
- Remove pad control code from the Gemini driver
- Use %pOF to print OF node full_name
- Various fixes in the physmap_of driver
- Remove unused vars in mtdswap
- Check devm_kzalloc() return value in the spear_smi driver
- Check clk_prepare_enable() return code in the st_spi_fsm driver
- Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
- Fix memory leaks in the core
- Remove unused NAND locking support
- Rename nand.h into rawnand.h (preparing support for spi NANDs)
- Use NAND_MAX_ID_LEN where appropriate
- Fix support for 20nm Hynix chips
- Fix support for Samsung and Hynix SLC NANDs
- Various cleanup, improvements and fixes in the qcom driver
- Fixes for bugs detected by various static code analysis tools
- Fix mxc ooblayout definition
- Add a new part_parsers to tmio and sharpsl platform data in order
to define a custom list of partition parsers
- Request the reset line in exclusive mode in the sunxi driver
- Fix a build error in the orion-nand driver when compiled for ARMv4
- Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header Write a message for tag:"
* tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd: (74 commits)
mtd: nand: complain loudly when chip->bits_per_cell is not correctly initialized
mtd: nand: make Samsung SLC NAND usable again
mtd: nand: tmio: Register partitions using the parsers
mfd: tmio: Add partition parsers platform data
mtd: nand: sharpsl: Register partitions using the parsers
mtd: nand: sharpsl: Add partition parsers platform data
mtd: nand: qcom: Support for IPQ8074 QPIC NAND controller
mtd: nand: qcom: support for IPQ4019 QPIC NAND controller
dt-bindings: qcom_nandc: IPQ8074 QPIC NAND documentation
dt-bindings: qcom_nandc: IPQ4019 QPIC NAND documentation
dt-bindings: qcom_nandc: fix the ipq806x device tree example
mtd: nand: qcom: support for different DEV_CMD register offsets
mtd: nand: qcom: QPIC data descriptors handling
mtd: nand: qcom: enable BAM or ADM mode
mtd: nand: qcom: erased codeword detection configuration
mtd: nand: qcom: support for read location registers
mtd: nand: qcom: support for passing flags in DMA helper functions
mtd: nand: qcom: add BAM DMA descriptor handling
mtd: nand: qcom: allocate BAM transaction
mtd: nand: qcom: DMA mapping support for register read buffer
...
This macro is useful to avoid link error on 32-bit systems.
We have the same definition in two drivers, so move it to
include/linux/kernel.h
While we are here, refactor DIV_ROUND_UP_ULL() by using
DIV_ROUND_DOWN_ULL().
Link: http://lkml.kernel.org/r/1500945156-12907-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.
Fixes: fe9d7cb22e ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make the position an in/out argument like all the other read/write
helpers and and make the buf argument a void pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use proper ssize_t and size_t types for the return value and count
argument, move the offset last and make it an in/out argument like
all other read/write helpers, and make the buf argument a void pointer
to get rid of lots of casts in the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
-----BEGIN PGP SIGNATURE-----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=bC1+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.14' of git://git.infradead.org/l2-mtd into mtd/next
From Boris:
"
This pull request contains the following core changes:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
"
commit c51d0ac59f ("mtd: nand: Move Samsung specific init/detection
logic in nand_samsung.c") introduced a regression for Samsung SLC NAND
chips. Prior to this commit chip->bits_per_cell was initialized by calling
nand_get_bits_per_cell() before using nand_is_slc().
With the offending commit this call is skipped, leaving
chip->bits_per_cell cleared to zero when the manufacturer specific
'.detect' function calls nand_is_slc() which in turn interprets
bits_per_cell != 1 as indication for an MLC chip.
The effect is that e.g. a K9F1G08U0F NAND chip is falsely detected as
MLC NAND with 4KiB page size rather than SLC with 2KiB page size.
Add a call to nand_get_bits_per_cell() before calling the .detect hook
function in nand_manufacturer_detect(), so that the nand_is_slc()
calls in the manufacturer specific code will return correct results.
Fixes: c51d0ac59f ("mtd: nand: Move Samsung specific init/detection logic in nand_samsung.c")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZo2HiAAoJEHm+PkMAQRiG3OcIAJqSeVK2uQ/QhmqFN1ExYay4
bdTjSTtSk7GH6PxI2C0cqfZvsxOUU7ICDHG8bYM1LA0S0SxfOtoFhHGKc/BcFLX8
MiKJWlF51ZbX0mkIEpKF+C8pRrXPgSqtk3N450/k2BzG9qCZSM93A2NCOB7v9T9w
XOBUIYHqfTS2tdmCinjwu8Ls+w8oPOGH1gLjxZyGnBlg4lTqHMcUufmHeVEAh11d
giGByqqqXH69kGD1HNC7H6quzXN9rz4n0gEwEG0mIhfkJ98b+ESSWwSEXXypOAQD
QT5/6+2YizXf5DPCqR46xasQCPjRsS6Sv0cF2cntW2PEAb4jBjhx5gTFlJcoOC8=
=efWJ
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc7' into mtd/next
Merge v4.13-rc7 back to resolve merge conflicts in
drivers/mtd/nand/nandsim.c and include/asm-generic/vmlinux.lds.h.
Version 4 of the ONFI spec mandates that tADL be at least 400 nanoseconds,
but, depending on the master clock rate, 400 ns may not fit in the tADL
field of the SMC reg. We need to relax the check and accept the -ERANGE
return code.
Note that previous versions of the ONFI spec had a lower tADL_min (100 or
200 ns). It's not clear why this timing constraint got increased but it
seems most NANDs are fine with values lower than 400ns, so we should be
safe.
Fixes: f9ce2eddf1 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The debugfs entries must be removed before an error is returned in the
probe function. Otherwise another try to load the module fails and when
the debugfs files are accessed without the module loaded, the kernel
still tries to call a function in that module.
Fixes: 5346c27c5f ("mtd: nandsim: Introduce debugfs infrastructure")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done in the board files using this driver.
Use now these parsers.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done in the board files using this driver.
Use now these parsers.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add the compatible string for IPQ8074 QPIC NAND controller
version 1.5.0 which uses BAM DMA and its FLASH_DEV_CMD registers
starting offset is 0x7000.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The FLASH_DEV_CMD registers starting offset is not same in
different QPIC NAND controller versions. This patch adds
the starting offset in NAND controller properties and uses
the same for calculating the actual offset of these registers.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. Add the data descriptor preparation function which will be used
only by BAM DMA for forming the data SGL’s
2. Add clear BAM transaction and call it before every new request
3. Check DMA mode for ADM or BAM and call the appropriate
descriptor formation function.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. DM_EN is only required for EBI2 NAND controller which uses ADM
2. BAM mode will be disabled after power on reset which needs to
be enabled before starting any BAM transfers.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller returns ECC failure during read of completely
erased codeword. The NAND controller has hardware functionality
to detect erased codeword in case of BCH ECC algorithm. The
NAND_ERASED_CW_DETECT_CFG register controls the erased
codeword/page detection controller. This register should be reset
before every page read by setting and clearing bit 0 of
NAND_ERASED_CW_DETECT_CFG.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In EBI2, all codeword data will be read in FLASH_BUF_ACC buffer
and ADM will copy the data from source (FLASH_BUF_ACC) to
destination (memory for data read).
In QPIC, there is no FLASH_BUF_ACC and all the codeword data will
held in QPIC BAM FIFO buffers. It provides multiple READ_LOCATION
registers which will be used for copying the data from FIFO to
memory. The READ_LOCATION register will be used to read a
specific amount of data from a specific offset within the flash
buffer. It supports sequential offset requests. Each request is
composed of the following fields:
a. Offset within the flash buffer from which data should be
read
b. Amount of data to be read
c. Flag bit specifying the last read request from the flash
buffer. Following the last read request the NANDc refers to the
buffer as empty.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The QPIC NAND BAM has multiple flags to control the transfer. This
patch adds flags parameter in register and data transfer DMA helper
functions and modifies all these functions call with appropriate
flags using following rule
1. Read and write can’t go in single command descriptor so
separate SGL should be used.
2. For some of the requests, NWD flag should be set in BAM
DMA descriptor.
3. For Data write, the BAM has internal buffer for each codeword.
All write request will modify the data in internal buffer and
this buffer will be flushed to NAND device once EOT flag is set.
So for all the write requests in single codeword, the EOT should
be cleared for all tx data descriptors except the last one.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. prepare_bam_async_desc is the function which will call
all the DMA API’s. It will fetch the outstanding scatter gather
list for passed channel and will do the DMA descriptor formation.
The DMA flag is dependent upon the type of channel.
2. For ADM DMA, the descriptor is being formed for every DMA
request so its sgl count will be always 1 while in BAM DMA, the
clubbing of descriptor is being done to increase throughput.
3. ADM DMA uses only one channel while in BAM DMA, data descriptors
will be submitted to tx channel (for write) or rx channel
(for read) and all the registers read/write descriptors in
command channel.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- The BAM transaction is the core data structure which will be used
for all the data transfers in QPIC NAND. Since the core framework
in nand_base.c is serializing all the NAND requests so allocating
BAM transaction before every transfer will be overhead. The memory
for it be allocated during probe time and before every transfer,
it will be cleared.
- The BAM transaction contains the array of
command and data scatter gather list and indexes. For
every transfer, all the resource will be taken from BAM
transaction.
- The size of the buffer used for BAM transactions
is calculated based on the NAND device with the maximum page size,
among all the devices connected to the
controller.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The EBI2 NAND controller directly remaps register read buffer with
dma_map_sg and DMA address of this buffer will be passed to DMA
API’s. While, on QPIC NAND controller, which uses BAM DMA, we read
the controller registers by preparing a BAM command descriptor. This
command descriptor requires the
- controller register address
- the DMA address in which we want to store the value read
back from the controller register.
This command descriptor will be remapped with dma_map_sg
and its DMA address will be passed to DMA API’s. Therefore,
it's required that we also map our register read buffer for
DMA (using dma_map_single). We use the returned DMA address
for preparing entries in our command descriptor.
This patch adds the DMA mapping support for register read
buffer. This buffer will be DMA mapped during allocation
time. Before starting of any operation, this buffer will
be synced for device operation and after operation
completion, it will be synced again for CPU.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. QPIC NAND controller uses 3 BAM channels: command, data tx
and data rx while EBI2 NAND controller uses only single ADM
channel.
2. CRCI is only required for ADM DMA and it's not required for
BAM DMA.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The current driver only supports EBI2 NAND controller which uses
ADM DMA. The latest QCOM SoC uses QPIC NAND controller with BAM
DMA. NAND registers and programming sequence are same for EBI2
and QPIC NAND so the same driver can support QPIC NAND also by
adding the BAM DMA support. This patch adds the is_bam in NAND
property which will be checked for determining the DMA engine type.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently driver data is being assigned directly with ECC modes.
Now, the plan is to add more NAND controller versions which will
have different properties. This patch reorganizes the current driver
data assignment by creating NAND controller properties structure
which will contain all properties specific to NAND controller.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is
0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID
The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
platform_get_irq() returns an error code, but the mtk_ecc driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
platform_get_irq() returns an error code, but the sh_flctl
driver ignores it and always returns -ENXIO. This is not correct
and, prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
