Currently we attempt to get the amount of flipped bits from a hardware
location which is reset on every subpage. Instead obtain total flipped
bits stat from hardware accumulator. In addition identify the correct
maximum subpage corrected bits.
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use kernel provided standard helper function to replace hard-coded
strings
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When booting a board to NAND and accessing NAND while eMMC
transactions are occurring the NAND will sometimes timeout. This
is due to both NAND and eMMC controller sharing the same data bus
on BCMBCA chips. Fix is to extend NAND timeout to allow eMMC
transactions time to complete.
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
last_cmd and last_byte are now unused brcmnand_host members.
last_addr is only written and never read so we can remove it too.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This change fixes an issue where an error return value may be mistakenly
used as NAND status.
Fixes: f504551b7f ("mtd: rawnand: Propagate error and simplify ternary operators for brcmstb_nand_wait_for_completion()")
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmc8is0ACgkQJWrqGEe9
VoRXDwf+IqUGLRVdCh9wQFsjEKXBX9lmLF+McG+aumLnpmxq+9iDs0FzPg39gi9W
iSZiYRnVNdOPskEMpJcAnalFcAT56SFjM7IUluxvMG4TKsaWqV7ZCP+fwV+43tyl
57ohTlQCpJnTAqUdARIMVPjIlBaXTsmzyt74nb3hOUGFa5NKwF7PxBP0e504akUP
TohLFHWOO4BeooqkDroz8H3Po+uO3YDVf3l0DsGANptAmA0azDjj+ZUEKOtsNEQw
ZmeZ8sGZGYswrcjYqJAGKXeXBOBmfFSTlEy72cKKqs8KBGqGCRTyoDjVpIBNK+vl
vyMY8AoViWX5nb83Qu85QckJbQlEqw==
=GEHJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.13' into mtd/next
SPI-NAND changes:
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mtd to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007205803.444994-10-u.kleine-koenig@baylibre.com
BCMBCA broadband SoC based board design does not specify ecc setting in
dts but rather use the SoC NAND strap info to obtain the ecc strength
and spare area size setting. Add brcm,nand-ecc-use-strap dts propety for
this purpose and update driver to support this option. However these two
options can not be used at the same time.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240301173308.226004-1-william.zhang@broadcom.com
The write protection feature is controlled by the module parameter wp_on
with default set to enabled. But not all the board use this feature
especially in BCMBCA broadband board. And module parameter is not
sufficient as different board can have different option. Add a device
tree property and allow this feature to be configured through the board
dts on per board basis.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-14-william.zhang@broadcom.com
The BCMBCA broadband SoC integrates the NAND controller differently than
STB, iProc and other SoCs. It has different endianness for NAND cache
data.
Add a SoC read data bus shim for BCMBCA to meet the specific SoC need
and performance improvement using the optimized memcpy function on NAND
cache memory.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-12-william.zhang@broadcom.com
In preparing to support multiple BCMBCA SoCs, rename bcm63138 to bcmbca
in the driver code and driver file name.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-11-william.zhang@broadcom.com
Update log level messages so that more critical messages can be logged
to console and help the troubleshooting with field devices.
Signed-off-by: David Regan <dregan@broadcom.com>
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-4-william.zhang@broadcom.com
exec_op implementation for Broadcom STB, Broadband and iProc SoC
This adds exec_op and removes the legacy interface. Based on changes
proposed by Boris Brezillon.
Link: 4ec6f8d8d8
Link: 11b4acffd7
Signed-off-by: David Regan <dregan@broadcom.com>
[Miquel Raynal: Misc style fixes]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231125012438.15191-4-dregan@broadcom.com
Pass host struct to bcmnand_ctrl_poll_status instead of ctrl struct
since real time status requires host, and ctrl is a member of host.
Real time status is required for low level commands vs cached status
since the NAND controller will not do an automatic status read at the
end of a low level command as it would with a high level command.
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231125012438.15191-3-dregan@broadcom.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
By changing the function brcmnand_remove() to return void several
drivers that use this function as remove callback can be converted to
.remove_new().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231102220246.3336154-7-u.kleine-koenig@pengutronix.de
As bcmnand_ctrl_poll_status() return negative errno, so return true if
sts < 0. The < 0 case does not exist for wait_for_completion_timeout(),
so return true if sts = 0 and zero otherwise. Both of the true return
of them can be considered as a -ETIMEDOUT err, so return -ETIMEDOUT
if err is true to propagate err from its caller.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230808032943.3890545-1-ruanjinjie@huawei.com
Convert platform_get_resource_byname() + devm_ioremap_resource() to a
single call to devm_platform_ioremap_resource_byname(), as this is
exactly what this function does.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230802013500.1030853-1-lizetao1@huawei.com
MTD subsystem may return -EPROBE_DEFER if something isn't ready yet.
It's important to pass that error up so device will get probed later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230719084324.14799-1-zajec5@gmail.com
brcmnand controller can only access the flash spare area up to certain
bytes based on the ECC level. It can be less than the actual flash spare
area size. For example, for many NAND chip supporting ECC BCH-8, it has
226 bytes spare area. But controller can only uses 218 bytes. So brcmand
driver overrides the mtd oobsize with the controller's accessible spare
area size. When the nand base driver utilizes the nand_device object, it
resets the oobsize back to the actual flash spare aprea size from
nand_memory_organization structure and controller may not able to access
all the oob area as mtd advises.
This change fixes the issue by overriding the oobsize in the
nand_memory_organization structure to the controller's accessible spare
area size.
Fixes: a7ab085d7c ("mtd: rawnand: Initialize the nand_device object")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-6-william.zhang@broadcom.com
When the oob buffer length is not in multiple of words, the oob write
function does out-of-bounds read on the oob source buffer at the last
iteration. Fix that by always checking length limit on the oob buffer
read and fill with 0xff when reaching the end of the buffer to the oob
registers.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-5-william.zhang@broadcom.com
If system is busy during the command status polling function, the driver
may not get the chance to poll the status register till the end of time
out and return the premature status. Do a final check after time out
happens to ensure reading the correct status.
Fixes: 9d2ee0a60b ("mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-3-william.zhang@broadcom.com
v7.2 controller has different ECC level field size and shift in the acc
control register than its predecessor and successor controller. It needs
to be set specifically.
Fixes: decba6d478 ("mtd: brcmnand: Add v7.2 controller support")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-2-william.zhang@broadcom.com
Allow each platform to define a dedicated Kconfig entry for its glue
driver such that we can decide on a per-platfomr basis whether to build
it or not. This allows for a finer grained control over the resulting
kernel image or set of modules.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220711222323.4048197-3-f.fainelli@gmail.com
In preparation for allowing each of the brcmnand stub to be built
separately, move the Kconfig entry to the driver folder.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220711222323.4048197-2-f.fainelli@gmail.com
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI021sACgkQJWrqGEe9
VoTEcggAiFXD+oR0VXTsykiNDiopsAUZwLPGuqk8gvD4ozOYCoAEoYrtnBM6Uybz
W6Hu6Eow/ri1H+uVygUw3RYa4TpxrZrmZnJ1YimXxZjbLYjgE3FS9vzh2l4Bu3yo
fkkQH+nFvk9qVIK8qolAny+LWl37gkSnCd6mPPksYaG5Ds1n1ZgyTZVUz5TOWAjG
QAWUQQfO1iu7+u4CXa9JRTkCf55bT6v6c9Ryq6MA+ok6jVRN6Cj9WhxHtCB5vmOH
Ndmu4V8BqaNKg39ltolqSPuwt3GEh707LRr+YakfnaOM7Sf8E/evn/THSkHwY/yn
bAjpU1gvS13nJ++s8nHwIhHKhoYjTg==
=4Uke
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.18' into mtd/next
Raw NAND core changes:
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmInffUACgkQS1VPR6WN
FOn9fwf/SCIvgoScBNeQjW4cGTmh11oO+O8i2umibq0pQDLrNF6Ul7ykY6Fdm4Dc
+Ce7c4Vp0O+DRphIkaK5MtNgRmXMOQbqUKcNAQftFS0wCtJ+QVQzOvkVGS3jQA74
KVEY3Jiup3Q5qknBg0r890ENwRLmcGJaPi5DAO+uHcf6ItTpwjv3z6C2ZUeiH6UK
PMSwZgd86dwwH2eU4G5EoAjA+nqOcVvH0V1F49DFsGZ3kkmUS6nMNnSpb5SykszT
4uq+7+c3E2UOC0TlUkyX/xTv4DoZZDi6qqVEaV14bELL1a0FdltjKyIuWTds1Tei
rwPhEOkqOpSnBVjlUWb7icwef21NWg==
=QFe+
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.18' into mtd/next
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
On non-OF enabled platforms (CONFIG_OF is not set), of_match_node() will
expand to NULL. The of_device_id array pointed by the macro will then be
left unused. Let's mark the array __maybe_unused in this case to prevent
compiler warnings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20220127110802.1064963-1-miquel.raynal@bootlin.com
The brcmnand driver contains a bug in which if a page (example 2k byte)
is read from the parallel/ONFI NAND and within that page a subpage (512
byte) has correctable errors which is followed by a subpage with
uncorrectable errors, the page read will return the wrong status of
correctable (as opposed to the actual status of uncorrectable.)
The bug is in function brcmnand_read_by_pio where there is a check for
uncorrectable bits which will be preempted if a previous status for
correctable bits is detected.
The fix is to stop checking for bad bits only if we already have a bad
bits status.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: david regan <dregan@mail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/trinity-478e0c09-9134-40e8-8f8c-31c371225eda-1643237024774@3c-app-mailcom-lxa02
Add a BCMA shim to allow us to register the brcmnand driver using the
BCMA bus which provides indirect memory mapped access to SoC registers.
There are a number of registers that need to be byte swapped because
they are natively big endian, coming directly from the NAND chip, and
there is no bus interface unlike the iProc or STB platforms that
performs the byte swapping for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-10-f.fainelli@gmail.com
For some odd and unexplained reason the BCMA NAND controller, albeit
revision 3.4 uses a command shift of 0 instead of 24 as it should be,
quirk that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-9-f.fainelli@gmail.com
Make use of the recently refactored code in brcmnand_init_cs() and
derive the chip-select from the platform data that is supplied. Update
the various code paths to avoid relying on possibly non-existent
resources, too.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-8-f.fainelli@gmail.com
The BCMA devices include the brcmnand controller but they do not wire up
any interrupt line, allow the main interrupt to be optional and update
the completion path to also check for the lack of an interrupt line.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-6-f.fainelli@gmail.com
In order to initialize a given chip select object for use by the
brcmnand driver, move all of the Device Tree specific routines outside
of brcmnand_init_cs() in order to make it usable in a platform data
configuration which will be necessary for supporting BCMA chips.
No functional changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-5-f.fainelli@gmail.com
In preparation for encapsulating more of what the loop calling
brcmnand_init_cs() does, avoid using platform_device when it is the
device behind platform_device that we are using for printing errors.
No functional changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-4-f.fainelli@gmail.com
Allow a brcmnand_soc instance to provide a custom set of I/O operations
which we will require when using this driver on a BCMA bus which is not
directly memory mapped I/O. Update the nand_{read,write}_reg accordingly
to use the SoC operations if provided.
To minimize the penalty on other SoCs which do support standard MMIO
accesses, we use a static key which is disabled by default and gets
enabled if a soc implementation does provide I/O operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-3-f.fainelli@gmail.com
In order to key off the brcmnand_probe() code in subsequent changes
depending upon ctrl->soc, assign that variable as early as possible,
instead of much later when we have checked that it is non-NULL.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-2-f.fainelli@gmail.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074108.8933-1-caihuoqing@baidu.com
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210224080210.23686-1-noltari@gmail.com
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'host' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'addr' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'buf' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'len' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'cmd' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'host' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'desc' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'addr' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'buf' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'len' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'dma_cmd' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'begin' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'end' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'next_desc' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'host' not described in 'brcmnand_dma_run'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'desc' not described in 'brcmnand_dma_run'
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-14-lee.jones@linaro.org
