Apart from a binding conversion to yaml, only minor changes/small fixes
have been merged.
* Raw NAND changes:
Various controller drivers received minor fixes like DMA mapping checks,
better timing derivations or bitflip statistics.
It has also been discovered that some Hynix NAND flashes were not
supporting read-retries, which is not properly supported.
* SPI NAND changes:
In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
* SPI NOR changes:
A notable changes is the fix for exiting 4-byte addressing on Infineon
SEMPER flashes. These flashes do not support the standard EX4B
opcode (E9h), and use a vendor-specific opcode (B8h) instead.
There is also a fix for unlocking flashes that are write-protected at
power-on. This was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all().
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmiLn/sACgkQJWrqGEe9
VoTGowf/c6kynDuMlQbTANv/UIYX/LRFZsnIx0LB32LWrhLaUIBsbFxejyt07WG9
ryej+xRUtSHGsqMIw+B/PjvA4hUNLdsSwO/udIwstXNQjJcO9OKp/ucpvlxLzIha
REq8IifvT9vLLA+Efoq2L25dM14KjuFCAjwm3GH/SmdTOqPhI/Bbnx4vRWIPeXrx
XZ69ovIiu5NqLTD5IFGsu+omhbFWlDtVALtKNknrTOXWrjLZhDpieO4f7M9rvru6
OwazFQAWuixzqZRMFqvOzu8KUDnOHi9gHrzi6tS7T1zBUDz9ywdBtaHYCd7VlMJh
uV1wjUdWjnIh9E8R/llv3D+ko1Ya1w==
=IS/d
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD changes:
- Apart from a binding conversion to yaml, only minor changes/small
fixes have been merged.
Raw NAND changes:
- Minor fixes for various controller drivers like DMA mapping checks,
better timing derivations or bitflip statistics.
- some Hynix NAND flashes were not supporting read-retries, so don't
even try to do it
SPI NAND changes:
- In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
- Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
SPI NOR changes:
- A notable changes is the fix for exiting 4-byte addressing on
Infineon SEMPER flashes. These flashes do not support the standard
EX4B opcode (E9h), and use a vendor-specific opcode (B8h) instead.
- There is also a fix for unlocking flashes that are write-protected
at power-on. This was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all()"
* tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (26 commits)
mtd: spinand: winbond: Add comment about the maximum frequency
mtd: spinand: winbond: Enable high-speed modes on w35n0xjw
mtd: spinand: winbond: Enable high-speed modes on w25n0xjw
mtd: spinand: Add a ->configure_chip() hook
mtd: spinand: Add a frequency field to all READ_FROM_CACHE variants
mtd: spinand: Fix macro alignment
spi: spi-mem: Take into account the actual maximum frequency
spi: spi-mem: Use picoseconds for calculating the op durations
mtd: rawnand: atmel: set pmecc data setup time
mtd: spinand: propagate spinand_wait() errors from spinand_write_page()
mtd: rawnand: fsmc: Add missing check after DMA map
mtd: rawnand: rockchip: Add missing check after DMA map
mtd: rawnand: hynix: don't try read-retry on SLC NANDs
mtd: rawnand: atmel: Fix dma_mapping_error() address
mtd: nand: brcmnand: fix mtd corrected bits stat
mtd: rawnand: renesas: Add missing check after DMA map
mtd: spinand: gigadevice: Add support for GD5F1GM9 chips
mtd: nand: brcmnand: replace manual string choices with standard helpers
mtd: map: Don't use "proxy" headers
mtd: spi-nor: Fix spi_nor_try_unlock_all()
...
Setup the pmecc data setup time as 3 clock cycles for 133MHz as recommended
by the datasheet.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Reported-by: Zixun LI <admin@hifiphile.com>
Closes: https://lore.kernel.org/all/c015bb20-6a57-4f63-8102-34b3d83e0f5b@microchip.com
Suggested-by: Ada Couprie Diaz <ada.coupriediaz@arm.com>
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The DMA map functions can fail and should be tested for errors.
Fixes: 058e0e847d ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some SLC NANDs like H27U4G8F2D expose a valid JEDEC ID yet they don't
support the read-retry mechanism, and fail.
Since SLC NANDs don't require read-retry, continue only if the bits per
cell is bigger than 1.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It seems like what was intended is to test if the dma_map of the
previous line failed but the wrong dma address was passed.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Rule: add
Link: https://lore.kernel.org/stable/20250702064515.18145-2-fourier.thomas%40gmail.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently we attempt to get the amount of flipped bits from a hardware
location which is reset on every subpage. Instead obtain total flipped
bits stat from hardware accumulator. In addition identify the correct
maximum subpage corrected bits.
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The DMA map functions can fail and should be tested for errors.
Fixes: d8701fe890 ("mtd: rawnand: renesas: Add new NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use kernel provided standard helper function to replace hard-coded
strings
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add defines for the values of the ECC_MODE field of the NAND_DEV0_ECC_CFG
register and change both the 'qcom-nandc' and 'spi-qpic-snand' drivers to
use those instead of magic numbers.
No functional changes. This is in preparation for adding 8 bit ECC strength
support for the 'spi-qpic-snand' driver.
Reviewed-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250702-qpic-snand-8bit-ecc-v2-1-ae2c17a30bb7@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
register a master device. This is a problem that has been there forever:
the "master" device was not always present depending on a number of
heuristics such as the presence of fixed partitions and the absence of a
Kconfig symbol to force its presence. This was a problem for runtime PM
operations which might not have the "master" device available in all
situation.
The SPI NAND subsystem has seen the introduction of DTR operations (the
equivalent of DDR transfers), which involved quite a few preparation
patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for old
legacy SoCs with an update of the ->exec_op() hook, there has been the
introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Finally, Macornix SPI NOR entries have been cleaned-up and some SFDP
table fixups for Macronix MX25L3255E have been merged.
Aside from this, there is the usual load of misc improvement, fixes,
and yaml conversion.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmg91NEACgkQJWrqGEe9
VoR8egf+JPTtykQ+Bip9bHStgfpxi0+OKL81PUuPBsbs5C546u5t6ZRhoPsU+KqL
ZTyUk3ys7HcSwZCuiS9V6ea6TNV1FvAVZm+ONpkuPnU60++z8YfVr8ZvtgT0IUXx
COi+5ksdsTFZMyRG+VybRKnYNrTYB7j7CqVL8ifxq1XYWnYdhjy5PH4DgAKnBhGL
523kN2eR85AhvJ4aulsKbcqQQYKvJIQbhjAKklA3yQVarDmoOdiSmndoZlRy+MDu
B9DaRMvRRa/g1nI0stvR9K7FtdSrMYTg4kowR9jPRx0zEZXFFsZbASgcC+3G7HdK
7rLFWrN+G6fitcEjeAnfyV+sKF48LA==
=tW1t
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"A big core MTD change is the introduction of a new class to always
register a master device. This is a problem that has been there
forever: the "master" device was not always present depending on a
number of heuristics such as the presence of fixed partitions and the
absence of a Kconfig symbol to force its presence. This was a problem
for runtime PM operations which might not have the "master" device
available in all situation.
The SPI NAND subsystem has seen the introduction of DTR operations
(the equivalent of DDR transfers), which involved quite a few
preparation patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for
old legacy SoCs with an update of the ->exec_op() hook, there has been
the introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Finally, Macornix SPI NOR entries have been cleaned-up and some SFDP
table fixups for Macronix MX25L3255E have been merged.
Aside from this, there is the usual load of misc improvement, fixes,
and yaml conversion"
* tag 'mtd/for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (42 commits)
mtd: rawnand: brcmnand: legacy exec_op implementation
mtd: rawnand: sunxi: Add randomizer configuration in sunxi_nfc_hw_ecc_write_chunk
mtd: nand: brcmnand: fix NAND timeout when accessing eMMC
mtd: nand: sunxi: Add randomizer configuration before randomizer enable
mtd: spinand: esmt: fix id code for F50D1G41LB
mtd: rawnand: brcmnand: remove unused parameters
mtd: core: always create master device
mtd: rawnand: loongson1: Fix inconsistent refcounting in ls1x_nand_chip_init()
mtd: rawnand: loongson1: Fix error code in ls1x_nand_dma_transfer()
mtd: rawnand: qcom: Fix read len for onfi param page
mtd: rawnand: qcom: Fix last codeword read in qcom_param_page_type_exec()
mtd: rawnand: qcom: Pass 18 bit offset from NANDc base to BAM base
dt-bindings: mtd: qcom,nandc: Document the SDX75 NAND controller
mtd: bcm47xxnflash: Add error handling for bcm47xxnflash_ops_bcm4706_ctl_cmd()
mtd: rawnand: Use non-hybrid PCI devres API
mtd: nand: ecc-mxic: Fix use of uninitialized variable ret
mtd: spinand: winbond: Add support for W35N02JW and W35N04JW chips
mtd: spinand: winbond: Add octal support
mtd: spinand: winbond: Add support for W35N01JW in single mode
mtd: spinand: winbond: Rename DTR variants
...
equivalent of DDR transfers), which involved quite a few preparation
patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for old
legacy SoCs with an update of the ->exec_op() hook, there has been the
introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Aside from this, there is the usual load of misc improvement and fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmg90ysACgkQJWrqGEe9
VoTK8gf/U+28sdthNVHENmeQwgzMdjAaZkEn0qftRVplPUTGSqvkrTBQ2tsyGVpj
V2jJ85WzQ6c+YVRjUsgojX4JClh0tfNrm8ySSu3TOAv98E/sCFttQgyCbELtt6GL
P4/1g/BqHlagi1ouU95AtH3njZX9qXBq9cQGz3ZWX+qeS0p52wPsj1G8iy6syBR+
M6GZI92iINSXJUBlFBXzijDSxqcLWsAg8P2E5dTyL9Ukjcju0+fSQtt1oCp1F50+
zXJHfj3mB+BtBnX6nGhMu3sqY7LaM2NpEq7k6xtvo9ivWZwFAOK+uc31iGvAcKaZ
R1A72QkRE3e0vQZjrX1JKZvXMVXt4Q==
=Uj/O
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.16' into mtd/next
The SPI NAND subsystem has seen the introduction of DTR operations (the
equivalent of DDR transfers), which involved quite a few preparation
patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for old
legacy SoCs with an update of the ->exec_op() hook, there has been the
introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Aside from this, there is the usual load of misc improvement and fixes.
The function sunxi_nfc_hw_ecc_write_chunk() calls the
sunxi_nfc_hw_ecc_write_chunk(), but does not call the configuration
function sunxi_nfc_randomizer_config(). Consequently, the randomization
might not conduct correctly, which will affect the lifespan of NAND flash.
A proper implementation can be found in sunxi_nfc_hw_ecc_write_page_dma().
Add the sunxi_nfc_randomizer_config() to config randomizer.
Fixes: 4be4e03efc ("mtd: nand: sunxi: add randomizer support")
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When booting a board to NAND and accessing NAND while eMMC
transactions are occurring the NAND will sometimes timeout. This
is due to both NAND and eMMC controller sharing the same data bus
on BCMBCA chips. Fix is to extend NAND timeout to allow eMMC
transactions time to complete.
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In sunxi_nfc_hw_ecc_read_chunk(), the sunxi_nfc_randomizer_enable() is
called without the config of randomizer. A proper implementation can be
found in sunxi_nfc_hw_ecc_read_chunks_dma().
Add sunxi_nfc_randomizer_config() before the start of randomization.
Fixes: 4be4e03efc ("mtd: nand: sunxi: add randomizer support")
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
last_cmd and last_byte are now unused brcmnand_host members.
last_addr is only written and never read so we can remove it too.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The minimum size to fetch the data from device to QPIC buffer
is 512-bytes. If size is less than 512-bytes the data will not be
protected by ECC as per QPIC standard. So while reading onfi parameter
page from NAND device set nandc->buf_count = 512.
Cc: stable@vger.kernel.org
Fixes: 89550beb09 ("mtd: rawnand: qcom: Implement exec_op()")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
For QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".
qcom_param_page_type_exec() is used to read only one code word
If it configures the number of code words to 1 in QPIC_NAND_DEV0_CFG0
register then QPIC controller thinks its reading the last code word,
since we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n" register
to fetch data from QPIC buffer to system memory.
Without this change page read was failing with timeout error
/ # hexdump -C /dev/mtd1
[ 129.206113] qcom-nandc 1cc8000.nand-controller: failure to read page/oob
hexdump: /dev/mtd1: Connection timed out
This issue only seen on SDX targets since SDX target used QPICv2. But
same working on IPQ targets since IPQ used QPICv1.
Cc: stable@vger.kernel.org
Fixes: 89550beb09 ("mtd: rawnand: qcom: Implement exec_op()")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The BAM command descriptor provides only 18 bits to specify the BAM
register offset. Additionally, in the BAM command descriptor, the BAM
register offset is supposed to be specified as "(NANDc base - BAM base)
+ reg_off". Since, the BAM controller expecting the value in the form of
"NANDc base - BAM base", so that added a new field 'bam_offset' in the NAND
properties structure and use it while preparing the command descriptor.
Previously, the driver was specifying the NANDc base address in the BAM
command descriptor.
Cc: stable@vger.kernel.org
Fixes: 8d6b6d7e13 ("mtd: nand: qcom: support for command descriptor formation")
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Tested-by: Gabor Juhos <j4g8y7@gmail.com> # on IPQ9574
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The function bcm47xxnflash_ops_bcm4706_cmd_ctrl() calls the function
bcm47xxnflash_ops_bcm4706_ctl_cmd(), but does not check its return value.
A proper implementation can be found in bcm47xxnflash_ops_bcm4706_write().
Add error log to the bcm47xxnflash_ops_bcm4706_ctl_cmd() via pr_err()
to prevent silent failure. The error Log funciton 'dev_err' is unsuitable
in this situation for it is hard to get device pointer.
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
denali_pci.c enables a PCI device with pcim_enable_device(). This,
implicitly, switches the function pci_request_regions() into managed
mode, where it becomes a devres function.
The PCI subsystem wants to remove this hybrid nature from its
interfaces. To do so, users of the aforementioned combination of
functions must be ported to non-hybrid functions.
Moreover, since both functions are already managed in this driver, the
calls to pci_release_regions() are unnecessary.
Remove the calls to pci_release_regions().
Replace the call to sometimes-managed pci_request_regions() with one to
the always-managed pcim_request_regions().
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Enabling the compile test should not cause automatic enabling of all
drivers, but only allow to choose to compile them.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In r852_ready(), the dev get from r852_get_dev() need to be checked.
An unstable device should not be ready. A proper implementation can
be found in r852_read_byte(). Add a status check and return 0 when it is
unstable.
Fixes: 50a487e771 ("mtd: rawnand: Pass a nand_chip object to chip->dev_ready()")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The atmel,dataflash binding has been converted to yaml and the physmap
one constrained. Some logs are improved, error path are getting reworked
a bit, few patches target the use of str_enabled_disabled().
* Raw NAND changes:
i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
* SPI NAND changes:
Two main features have been added:
- OTP support has been brought, and ESMT and Micron manufacturer drivers
implement it.
- Read retry, and Macronix manufacturer driver implement it.
* SPI NOR changes:
Adding support for few flashes. Few cleanup patches for the core
driver, where we touched the headers inclusion list and we start using
the scope based mutex cleanup helpers.
There is as well a bunch of minor improvements and fixes in drivers and
bindings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmfkMTQACgkQJWrqGEe9
VoS+Fgf/apT4C5115f4EolKAcato3QpJ+J1+S0Oy6yYSKQVwKNa4NkdBIeKXfQLc
rjNdsoE9RmibCKViX3D3rjlMnynbkIr4F3YHbgP4lz7y2TQUVA7Dy0sp2RX+9M3G
+a5u6lfUyGA/uzJPJUESaPpjLWLg5uTRcduD8hGVid9D+/KFYWNF0EsufobT8JmT
X/R+aVS58W0uqLEJtiaINsD6D3f8ukMZCNgsvuAUINSUNUrX61pVQZwQAZ4eCCNa
W+YaLdsMtrwRBdoRGXfrElHEvnufglYocUo+9h8EOVMQ84rfNH363Nu+1WxTVGDj
GLB5O9knQFy7DR0M4gYBAqqji41nTg==
=O/Ud
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD changes:
- The atmel,dataflash binding has been converted to yaml and the
physmap one constrained. Some logs are improved, error path are
getting reworked a bit, few patches target the use of
str_enabled_disabled().
Raw NAND changes:
- i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
SPI NAND changes:
- OTP support has been brought, and ESMT and Micron manufacturer
drivers implement it.
- Read retry, and Macronix manufacturer driver implement it.
SPI NOR changes:
- Adding support for few flashes. Few cleanup patches for the core
driver, where we touched the headers inclusion list and we start
using the scope based mutex cleanup helpers.
There is also a bunch of minor improvements and fixes in drivers
and bindings"
* tag 'mtd/for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (34 commits)
dt-bindings: mtd: atmel,dataflash: convert txt to yaml
mtd: mchp48l640: Use str_enable_disable() in mchp48l640_write_prepare()
mtd: rawnand: gpmi: Use str_enabled_disabled() in gpmi_nand_attach_chip()
mtd: mtdpart: Do not supply NULL to printf()
dt-bindings: mtd: gpmi-nand: Add compatible string for i.MX8 chips
mtd: nand: Fix a kdoc comment
mtd: spinand: Improve spinand_info macros style
mtd: spi-nor: drop unused <linux/of_platform.h>
mtd: spi-nor: explicitly include <linux/of.h>
mtd: spi-nor: explicitly include <linux/math64.h>
mtd: spi-nor: macronix: add support for mx66{l2, u1}g45g
mtd: spi-nor: macronix: Add post_sfdp fixups for Quad Input Page Program
mtd: Fix error handling in mtd_device_parse_register() error path
mtd: capture device name setting failure when adding mtd
mtd: Add check for devm_kcalloc()
mtd: Replace kcalloc() with devm_kcalloc()
dt-bindings: mtd: physmap: Ensure all properties are defined
mtd: rawnand: brcmnand: fix PM resume warning
dt-bindings: mtd: mxc-nand: Document fsl,imx31-nand
mtd: spinand: macronix: Add support for read retry
...
i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
* SPI NAND changes:
Two main features have been added:
- OTP support has been brought, and ESMT and Micron manufacturer drivers
implement it.
- Read retry, and Macronix manufacturer driver implement it.
There is as well a bunch of minor improvements and fixes in drivers and
bindings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmfkLyUACgkQJWrqGEe9
VoTj/gf/UFLUlbCTTLpiKItXTTywW7EEe/8ZvVoki/D6gzKrjfMnVzYjxpLqYCnc
Qps6RtHPX8Xkq2f7FMFCxu6t49PLFjvo8JIdEC7Q1Bxf3JLAPtQXIXZfl+frtNnc
MqctdU4BU9up8u1mCajjzSWtaCeU3YBwNtH9fPMS65b5dfg1vfXr7oA/NqfMg3ql
b4dMYHXzPHk6TP59q3yaTqkFf92yXzgEUjM651uoAIzafVSpVHyOZriDit8A/A3f
lBM0+SEhEPBBhMvWf0FgzlqWidmCE+LZPTypdkgVamvqYPh/KYFUs14UDmJd/M1t
TwXf+Q5c6mnGfmiVVvfM1icp0Lyr+Q==
=W0/k
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.15' into mtd/next
* Raw NAND changes:
i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
* SPI NAND changes:
Two main features have been added:
- OTP support has been brought, and ESMT and Micron manufacturer drivers
implement it.
- Read retry, and Macronix manufacturer driver implement it.
There is as well a bunch of minor improvements and fixes in drivers and
bindings.
With some research in some obscure old QSDK, it was possible to find the
MASK of the last register there were still set with raw shift and
convert them to FIELD_PREP API.
This is only a cleanup and modernize the code a bit and doesn't make
any behaviour change.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix broken config in qcom_param_page_type_exec caused by copy-paste error
from commit 0c08080fd7 ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK")
In qcom_param_page_type_exec the value needs to be set to
nandc->regs->cfg0 instead of host->cfg0. This wrong configuration caused
the Qcom NANDC driver to malfunction on any device that makes use of it
(IPQ806x, IPQ40xx, IPQ807x, IPQ60xx) with the following error:
[ 0.885369] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[ 0.885909] nand: Micron NAND 256MiB 1,8V 8-bit
[ 0.892499] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.896823] nand: ECC (step, strength) = (512, 8) does not fit in OOB
[ 0.896836] qcom-nandc 79b0000.nand-controller: No valid ECC settings possible
[ 0.910996] bam-dma-engine 7984000.dma-controller: Cannot free busy channel
[ 0.918070] qcom-nandc: probe of 79b0000.nand-controller failed with error -28
Restore original configuration fix the problem and makes the driver work
again.
Also restore the wrongly dropped cpu_to_le32 to correctly support BE
systems.
Cc: stable@vger.kernel.org
Fixes: 0c08080fd7 ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK")
Tested-by: Robert Marko <robimarko@gmail.com> # IPQ8074 and IPQ6018
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
dma_map_single is using physical/bus device (DMA) but dma_unmap_single
is using framework device(NAND controller), which is incorrect.
Fixed dma_unmap_single to use correct physical/bus device.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Remap the slave DMA I/O resources to enhance driver portability.
Using a physical address causes DMA translation failure when the
ARM SMMU is enabled.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace dma_request_channel() with dma_request_chan_by_mask() and use
helper functions to return proper error code instead of fixed -EBUSY.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Changes to support DTR with spi-mem.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmeGgAIACgkQJNaLcl1U
h9CodQf9Eek9Usqn6GzjYI8MEAv5XfB0TjG/gleATAtc7Zk4R0Vwo4COnx2+5Fo/
03CV8yAt4Z0fjsD5mzWdnoiVNKCumpS+aFlzwVlOMq1KMYMH1AZAjqYeK9nHYpSn
U5lGse0C9DGrv2jb2KNA5yKGHL/ZquRyY4h0+CKG85jGpmpAWqBAcXaqXm02ts2Q
lTlymD0yefnatQ/0MrGj8bZF0q90Y7oTARDwMyh/MKMpPJslYI5AUT2USKT0qZsp
7sp9SpDE6gyoZy3q0sDXrmRKvMLpV5oLVN5amREnnokNeD9FAP8swDbNH48Fbrlm
4zE4CaHWv2mPSrcbBSJRZRNT/+Neqg==
=uA3v
-----END PGP SIGNATURE-----
Merge tag 'spi-mem-dtr-2' into nand/next
spi: Support DTR in spi-mem
Changes to support DTR with spi-mem.
Add support for the OOB layout used by the ROM bootloader.
The same layout is used by both Keystone [1] and OMAPL138/DA850 [2]
which currently is the only users of davinci-nand.
Only select this layout if the `nand-is-boot-medium` property is set.
This to avoid breaking any existing devices out there.
[1] https://www.ti.com/lit/ug/spruhj3/spruhj3.pdf
[2] https://www.ti.com/lit/an/sprab41f/sprab41f.pdf
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
For each NAND_OP_WAITRDY_INSTR operation, the NANDFSR register is
polled only once every 100 us to check for the EMA_WAIT pin. This
isn't frequent enough and causes delays in NAND accesses.
Set the polling interval to 5 us. It increases the page read speed
reported by flash_speed by ~30% (~10% on page writes).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
the spi bits adding the Qcom SPI-NAND controller driver re-using a lot
of code that has been shared.
With this goal in mind, the raw NAND controller driver has been cleaned
up and reorganized, and only the relevant structures/helpers which have
nothing raw NAND specific should now be exported.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmdq0moACgkQJWrqGEe9
VoS3cwgAh+aISqETMIQbG8/i2LzbBjzCAEDKC1nwnk2buwlvJC8omUDF6xpBe1AL
grN3j5ltmlDj834+S8UI9/9QFYExrKp3SlDzzbvdpDNgGsgFT56B2Mq0eZfju2b0
BXUuMUllKZGR6bm1ddKwEvFtgqulJdBiTOD28PIDsW1+ZgpFPLN7wYzyAme3s6Aw
xwqwthUWt7J3zXTMRxBAqwBG63Xkb30AiF0q7EYNzjZ6455c/XIJcTSmDTI9/Wx1
O2oBbG7EpbXlMISosiDkbBrfCseDduGpZLeCE7pMDkWpsdFJbV5qeM4z3UJvQ9vu
rLRMtSEhJ6tJF/dRn+YlqlIz72uKsQ==
=BqI2
-----END PGP SIGNATURE-----
Merge tag 'mtd/qcom-reorg-for-spi-6.14' into nand/next
Topic branch with preparation changes from Qcom in order to apply on top
the spi bits adding the Qcom SPI-NAND controller driver re-using a lot
of code that has been shared.
With this goal in mind, the raw NAND controller driver has been cleaned
up and reorganized, and only the relevant structures/helpers which have
nothing raw NAND specific should now be exported.
Use the bitfield macro FIELD_PREP, and GENMASK to
do the shift and mask in one go. This makes the code
more readable.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add qpic_common.c file which hold all the common
qpic APIs which will be used by both qpic raw nand
driver and qpic spi nand driver.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add qcom prefix to all the api which will be commonly
used by spi nand driver and raw nand driver.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Perform a global cleanup of the Qualcomm NAND
controller driver with the following improvements:
- Remove register value indirection API
- Remove set_reg() API
- Convert read_loc_first & read_loc_last macro to functions
- Rename multiple variables
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The setup_interface() operation isn't implemented. It forces the driver
to use the ONFI mode 0, though it could use more optimal modes.
Implement the setup_interface() operation. It uses the
aemif_set_cs_timings() function from the AEMIF driver to update the
chip select timings. The calculation of the register's contents is
directly extracted from §20.3.2.3 of the DaVinci TRM [1]
MAX_TH_PS and MAX_TSU_PS are the worst case timings based on the
Keystone2 and DaVinci datasheets.
[1] : https://www.ti.com/lit/ug/spruh77c/spruh77c.pdf
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NAND controller has a reference clock inherited from the AEMIF
(cf. Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt)
This clock isn't used yet by the driver.
Add a struct clock in the struct davinci_nand_info so it can be used
to compute timings.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
