The ADP558x family supports a built in keypad matrix decoder which can
be added as an Input device. In order to both support the Input and the
GPIO device, we need to create a bitmap of the supported pins and track
their usage since they can either be used as GPIOs (GPIs) or as part of
the keymap.
We also need to mark special pins busy in case some features are being
used (ex: pwm or reset events).
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-14-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP558x family of devices can be programmed to respond to some
especial events, In case of the unlock events, one can lock the keypad
and use KEYS or GPIs events to unlock it. For the reset events, one can
again use a combinations of GPIs/KEYs in order to generate an event that
will trigger the device to generate an output reset pulse.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-13-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
These devices are capable of generate FIFO based events based on KEY or
GPI presses. Add support for handling these events. This is in
preparation of adding full support for keymap and gpis based events.
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-12-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
There are some differences in the register map between the devices.
Hence, add a register structure per device. This will be needed in
following patches.
On top of that adp5585_fill_regmap_config() is renamed and reworked so
that the current struct adp5585_info act as template (they indeed
contain all the different data between variants) which can then be
complemented depending on the device (as identified by the id register).
This is done like this since a lot of the data is pretty much the same
between variants of the same device.
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-8-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
The only thing changing between variants is the regmap default
registers. Hence, instead of having a regmap configuration for every
variant (duplicating lots of fields), add a chip info type of structure
with a regmap ID to identify which defaults to use and populate
regmap_config at runtime given a template plus the id. Also note that
between variants, the defaults can be the same which means the chip info
structure can be used in more than one compatible.
This will also make it simpler adding new chips with more variants.
Also note that the chip info structures are deliberately not const as
they will also contain lots of members that are the same between the
different devices variants and so we will fill those at runtime.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-6-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
Use the helper macro. No functional change intended...
Whilst we're at it, now seems like a good time to update the Copyright.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-4-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
Make sure to enable the oscillator in the top device. This will allow to
not control this in the child PWM device as that would not work with
future support for keyboard matrix where the oscillator needs to be
always enabled (and so cannot be disabled by disabling PWM).
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-3-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
Not all devices (features) of the adp5585 device are mandatory to be
used in all platforms. Hence, check what's given in FW and dynamically
create the mfd_cell array to be given to devm_mfd_add_devices().
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-2-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP5585 is a 10/11 input/output port expander with a built in keypad
matrix decoder, programmable logic, reset generator, and PWM generator.
This driver supports the chip by modelling it as an MFD device, with two
child devices for the GPIO and PWM functions.
The driver is derived from an initial implementation from NXP, available
in commit 8059835bee19 ("MLK-25917-1 mfd: adp5585: add ADI adp5585 core
support") in their BSP kernel tree. It has been extensively rewritten.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240722121100.2855-3-laurent.pinchart@ideasonboard.com
Signed-off-by: Lee Jones <lee@kernel.org>
