This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Errata:
Certain conditions on the scsi bus may casue the 53C1030 to incorrectly signal
a SCSI_DATA_UNDERRUN to the host.
Workaround 1:
For an Errata on LSI53C1030 When the length of request data
and transfer data are different with result of command (READ or VERIFY),
DID_SOFT_ERROR is set.
Workaround 2:
For potential trouble on LSI53C1030. It is checked whether the length of
request data is equal to the length of transfer and residual.
MEDIUM_ERROR is set by incorrect data.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver is modified to return DID_NO_CONNECT for all pending I/O
requests for bus type SAS, if it founds the target is removed at
the firmware level.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Do not set max_id value received from FW. Once SAS transport layer is
introduced max_id value is missleading to SCSI mid layer. Use max_id to
infinite value.
logic of can queue of scsi host is changed.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Several of the doc book in the previous patches had incorrect multi-line short
function descriptors. Fixed it all to be the correct single line descriptor.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware is able to handle Broadcast primitives, but upstream driver does not
have support for broadcast primitive handling. Now this patch is mainly to
support broadcast primitives.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1. Handle integrated Raid device(Add/Delete) and error condition and check
related to Raid device. is_logical_volume will represent logical volume
device.
2. Raid device dual port support is added. Main functions to support this
feature are mpt_raid_phys_disk_get_num_paths and mpt_raid_phys_disk_pg1.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Resending patch considering Grants G's code review.
Main goal to submit this patch is code cleaup.
1. Better driver debug prints and code indentation.
2. fault_reset_work_lock is not used anywhere. driver is using taskmgmt_lock
instead of fault_reset_work_lock.
3. setting pci_set_drvdata properly.
4. Ingore config request when IOC is in reset state.( ioc_reset_in_progress
is set).
5. Init/clear managment frame proprely.(INITIALIZE_MGMT_STATUS and
CLEAR_MGMT_STATUS)
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1) rewrite of ioctl_cmds internal generated function that issue commands to
firmware, porting them to be single threaded using the generic MPT_MGMT
struct. All wait Queues are replace by completion Queue.
2) added seperate callback handler for ioctl task managment
(mptctl_taskmgmt_reply), to handle command that timeout
3) rewrite mptctl_bus_reset
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) Added taskmgmt_quiesce_io flag in IOC and removed resetPending from
_MPT_SCSI_HOST struct.
2.) Reset from Scsi mid layer and internal Reset are seperate context.
Adding DeviceResetCtx for internal Device reset frame.
mptsas_taskmgmt_complete is optimized as part of implementation.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) rewrite taskmanagement request and completion routines, making them
single threaded and using the generic MPT_MGMT struct, deleting
mptscsih_TMHandler, replacing with single request TM handler
mptscsih_IssueTaskMgmt, and killing the watchdog timer functions.
2.) cleanup ioc_reset callback handlers, introducing wrappers for
synchronizing error recovery (mpt_set_taskmgmt_in_progress_flag,
mpt_clear_taskmgmt_in_progress_flag), as the fusion firmware only handles
one task management request at a time
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rewrite of all internal generated functions that issue commands to firmware,
porting them to be single threaded using the generic MPT_MGMT
struct. Implemented using completion Queue.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The reason for this change is there is a data corruption when four different
physical memory regions in the 36GB to 37GB region are
accessed. This is only affecting 1078.
The solution is we need to use different addressing when filling in
the scatter gather table for the effected memory regions. So instead
of snooping on all four different memory holes, we treat any physical
addresses in the 36GB address with the same algorithm.
The fix is explained below
1) Ensure that the message frames are NOT located in the trouble
region. There is no remapping available for message frames, they must
be allocated outside the problem region.
2) Ensure that Sense buffers are NOT in the trouble region. There is
no remapping available.
3) Walk through the SGE entries and if any are inside the trouble region
then they need to be remapped as discussed below.
1) Set the Local Address bit in the SGE Flags field.
MPI_SGE_FLAGS_LOCAL_ADDRESS
2) Ensure we are using 64-bit SGEs
3) Set MSb (Bit 63) of the 64-bit address, this will indicate buffer
location is Host Memory.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A bug in the fusion driver was exposed by the switch to block timeout.
Basically, drivers are supposed to terminate commands once error
handling begins on them. The fusion apparently wasn't doing this.
Under the old timeout regime, completions on terminated commands would
by and large get ignored because of the way command timeouts used to
work. The new block timers are very intolerant to this, though,
becuase the request gets cleaned and freed.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=12195
Reported-by: Alex Shi <alex.shi@intel.com>
Tested-by: Ming Lin <ming.m.lin@intel.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make SPI timeout 10s the same as SAS
Signed-off-by: Bernd Schubert <bs@q-leap.de>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Updating copyright statement to include the year 2008
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following a hard reset of a SAS raid, one of the raid targets is occasionally
missing. I tracked this down to a pretty obscure little bug.
The LSI fusion drivers for SAS and Fibre Channel both use their respective
transport layers. Those transport layers increment the target number
assigned to new targets.
The routine __scsi_scan_target uses the "this_id" element of the Scsi_Host
structure to avoid scanning the scsi host adapter. Both fusion drivers set
"this_id" from a value returned in a firmware PortFacts response. For my
particular test case (SAS) the firmware id assigned to the initiator was
173. After enough raid resets to cause the raid targets to go and come a
sufficient number of times, the id assigned by the transport to a raid
target would match the id assigned by the host adapter to the "this_id"
field, resulting in that target not being scanned.
Fix by not assigning this_id and not checking it in slave_configure.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the semaphore inactive_list_mutex is used as a mutex, convert it to
the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The system power state changes like hibernation and standby are not happening
properly with 106XE controllers, this patch modifies the driver to free
resources and allocate resources in power management entry points
[jejb: compile fixes for upstream]
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix docbook problems in fusion source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix kernel-api docbook warnings.
Warning(linux-2.6.23-git8//drivers/message/fusion/mptscsih.c:2618): No description found for parameter 'sc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleaning up prints that use the xxx_printk API, in that the fusion
preamble "mptbase: iocX" follows the info provided by the print API.
The way its currently coded, the [H:C:T] print in sdev_printk will be
inbetween "mptbase" and "iocX", instead of before.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ScsiLookup is an array of pending scmd pointers that the scsi lld
maintains. This array is touched from queuecommand, eh threads, and
interrupt context. This array should put under locks, hence this patch
to synchronize its access. I've added some nice little function
wrappers for this, and moved the ScsiLookup array over to MPT_ADAPTER
struct.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is currently typecasting to obtain the shost hostdata. The
driver is updated to use the shost_priv macro.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleaning up code by accesing the ioc pointer directly instead of via hd->ioc. In the future, most data members of struct MPT_SCSI_HOST will be either deleted or moved to struct MPT_ADAPTER.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
common naming of vdevice through out driver
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Standardize all prints using common MYIOC_s_XXX_FMT macro defined in mptbase.h. Currently the driver uses several different methods to display info, where in some cases the "controller name" generating the printk is not provided.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recently LSI Logic Corp was renamed as LSI Corp, so whereever there is
a reference of LSI Logic, it is changed to LSI in mpt fusion driver
code.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added support for sending the task management requests through High priority
request FIFO instead of Doorbell writes when firmware support High priority
FIFO.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptscsih.c to support logging in MPT fusion
drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
A new sysfs attribute is added to retrieve and modify the debug level.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New sysfs scsi_host attributes are added to provide information about Firmware
version, BIOS version, MPI version and other product related information
signed-off-by: Sathya Praksh <sathya.prakash@lsi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If there is IO going to the volume while a hidden disk is being torn down,
there is a case where we would return a DID_NO_CONNECT for IO sent to the
volume. The end result is the volume goes read-only. This problem is due to the
fact the firmware mapped target ids saved in per device object is phys_disk_num
for hidden raid components, and target_id for the volume. There is a single
case when both phys_disk_num and target_id are equal, so enters this issue. We
fix this issue by checking the tflags when the device is torned down,
insuring the IO being completed is meant for hidden raid component, not the
volume. In addition to this fix, there are a couple other cases to address
hidden raid components. For instance task_abort and device reset are not
supported by mpt fw for hidden raid components, a bus reset would be required
or target reset to volume.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
nice cosmetic cleaning of eh thread callback funtions
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update assocated fusion sources with new support email address.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
TODO: use scsi_for_each_sg().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There are several cases where the fusion driver uses the logical || to
try to do an arithmetical or ... fix by replacing with |.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This address the issue of VMWare guest OS being remounted as read-only
becuase the underlying device was held busy too long and at the
same time address Engenio MPP driver concerns over infinite retries.
This patch removes the code that snoops the SAM STATUS on busy, which
would be returning DID_BUS_BUSY, instead we return the status as is.
Retry hanlding seems to be properly handled in scsi_softirq_done,
where a busy sam status would only occurr for the time specified by
(cmd->allowed +1) * cmd->timeout_per_command.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Honour the return value of pci_enable_device(), which
seems to be a desirable thing to do:
2.6.20-rc4
gcc (GCC) 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)
CC [M] drivers/message/fusion/mptbase.o
drivers/message/fusion/mptbase.c: In function `mpt_resume':
drivers/message/fusion/mptbase.c:1541: warning: ignoring return value
of `pci_enable_device', declared with attribute warn_unused_result
It also in turn has mptscsih_resume() honour the return value of
mpt_resume()
I'm not sure about the handling of the other potential error cases
in mpt_resume(), of which there appear to be many. But this does
seem to be a good start.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It seems that most of the code in mptscsih_resume() doesn't
do anything. This patch removes that code.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bump version, and fix email addr for lsi support
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
misc error handling bug fix's
- properly interpret iocstatus returned after task management request
- clear tmState after a failed doorbell
- cleanup mptscsih_taskmgmt_complete
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
inactive raid support, e.g. exposing hidden raid components
belonging to a volume that are inactive. Also misc bug fix's for
various raid asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
various string updates for iocstatus, logingo, and fw asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move some functions that only apply to the mptspi module over from mptscsih.c
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for greater than 255 target and luns.
Kill the hd->Target[] field, and change all references
of bus_id/target_id, to channel/id.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Add modinfo driver version support.
* Change copyright year to 2007.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Endian fix's for warnings found in ppc environment.
* Fix compile time warning when calling scsi_device_reprobe, where
in newer kernels this API expects its return value to be examined.
* Fix compile errors when debug messages are enabled.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A repost of a patch forwarded by Mikael Reed from 2006-12-20.
The fibre channel IOC may kill a request for a variety of
reasons, some of which may be recovered by a retry, some of
which are unlikely to be recovered. Return DID_ERROR
instead of DID_RESET to permit retry of the command,
just not an infinite number of them.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix's to insure proper status is returned to midlayer
when a task abort failed to be aborted by controller
firmware.
Also sanity checks to prevent scsi cmd from being
double completed during error recovery.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas nexus loss support for systems that suport failover.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding support for sas enclosures with smart drives.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver uses msleep_interruptible() in the code path responsible
for resetting the card's ports via the lsiutil command. If a
<ctrl-c> is received during the reset it can leave a port in such
a state that the only way to regain its use is to reboot the system.
Changing from msleep_interruptible() to msleep() corrects the problem.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move fibre channel event and reset handling to mptfc. This will
result in fewer changes over time that need to be applied to
either mptbase.c or mptscsih.c.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
mptbase.h
bump version number to 3.03.09
remove unneeded flags
define workq and remove old fc specific locks
mptbase.c
initialize new lock and don't initialize two removed locks
mptscsih.c
when firmware reports target is no longer there, return
DID_REQUEUE for fc hosts so that i/o doesn't get killed until
the transport has an opportunity to manage the loss via its
dev loss timer
when the "eh_abort" routine is called, check to see if the
driver has the command or not before looking to see if a reset
is pending. James Smart and I talked about this and believe
that the API for this routine is: if driver doesn't have
command, return SUCCESS. This change helps prevent a target
from being taken offline. SUCCESS is returned because it's
likely that the command completed after error recovery timed
it out but before it could be aborted.
provide a routine to queue work to newly created workq, and
use it.
remove "ioc" from mptscsih_abort() it was only used one time.
the other references were via hd->ioc, so I just moved it....
net change in references to ioc via hd->ioc is zero
move hd->resetPending test and hd->timeouts increment to after
the test for whether the command to be aborted remains known
to the driver
Make certain that the workq exists before queuing work to it.
mptfc.c
no longer need to lock rport data structures as I was able to
single thread the code! I fixed up the debug code to
eliminate compilation messages due to type mismatch in the
printk. Got rid of some no longer needed rport flags.
Initialize and destroy the workq used for the rescan work.
simplify the logic regarding the increment of
fc_rescan_work_count. use post increment and test for zero
vs. pre increment and test for one; eliminate work_count
variable: queue_work can be called with the work_lock held as
it doesn't sleep
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch handles case where raid hidden components
are not being removed when power turned off to device
attached to expander, as well as the case of
exposing raid components when power is turned back on
to devices attached to an expander. (This is a repost
of this patch, with mptsas_is_end_device declared
further up in the code.)
This patch contains some other miscellaneous bug fix's.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Suppport for exposing hidden raid components
for sg interface. The sdev->no_uld_attach flag
will set set accordingly.
The sas module supports adding/removing raid
volumes using online storage management application
interface.
This patch rely's on patch's provided to me
by Christoph Hellwig, that exports device_reprobe.
I will post those patch's on behalf of Christoph.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It makes no sense in keeping the target_id and bus_id
in the VirtDevice structure, when it can be obtained
from the VirtTarget structure.
In addition, this patch fix's couple compilation bugs
in mptfc.c when MPT_DEBUG_FC is enabled. This
provided by Micheal Reed.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Created a debug level MPT_DEBUG_VERBOSE_EVENTS.
Moving some of the more vebose debug messages
for firwmare events into new debug level. Also
added some more firmware events descriptions.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It was actually rendered unused by the move to the spi transport
class, but never taken out.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the first half of a patch to add the generic domain validation
to mptspi. It also creates a secondary "virtual" channel for raid
component devices since these are now exported with no_uld_attach.
What Eric and I would have really liked is to export all physical
components on channel 0 and all raid components on channel 1.
Unfortunately, this would result in device renumbering on platforms with
mixed RAID/Physical devices which was considered unacceptable for
userland stability reasons.
Still to be done is to plug back the extra parameter setting and DV
pieces on reset and hotplug.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use the hard coded value MPTCTL_EVENT_LOG_SIZE to fix
bug where in certain cases, the ioc->eventLogSize was
initialized.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds a sanity check in the interrupt routine
insures incoming message frames are a valid
message frames.
The code for setting 0xdeadbeaf in the freed message
frames, apparently was already submitted by Christoph
in previous patch submission.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch inhibits sending spi negotiation parameters
for non-configured devices from the slave_destroy function.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding verbose message returned from firmware
when a task mangment request fails.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, Jan 16, 2006 at 06:53:13PM -0700, Moore, Eric wrote:
> The task managment request timeout in the eh threads was set
> for U320 timing, which is between 2-5 seconds.
> This is too small for FC and SAS.
> According to the firmware engineers, Fibre needs to be 40 seconds
> and SAS needs to be 10 seconds.
The timeout selection should probably be done in a little helper instead
of duplicated in a few places. Updated patch below.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The prior fusion patches moved an invocation of a function,
mptscsih_TMHandler(), static to mptscsih.c into mptsas.c
Make the function unstatic, move the header to mptscsih.h and export it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This moves code intented for SAS from
the generic mptscsih module over to the
mptsas module.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert kmalloc + memset to kzalloc or kcalloc in fusion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This utilizes the hostdata area that is hung off of scsi_target and
scsi_device for saving unique firmware mapping. This will be required
for supporting new Fibre and SPI transport support.
This also fixs problems in error handling error code for SAS
controllers, in which the incorrect mapping was passed to the
firmware.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This moves some functions around from within the #define
MPTSCSIH_ENABLE_DOMAIN_VALIDATION area, in preperation for generic
domain validation.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This changes to SPI for the bus_type enumeration.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Syncronization for Domain Validation workqueue and the initiation of the
alternate controller. Its possible that dv could be terminated if the
workqueue on the 1st channel doesn complete in time before the 2nd channel
begins initialization.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Thursday, September 15, 2005 6:22 AM, Christoph Hellwig wrote:
> Looks good to me, except for the spurious scsi_print_command prototype
> in mptscsih.h.
The attached patch addresses that concern.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Summary of Changes:
* splitting mpt_interrupt per Christophs suggestion
about a month ago
* rename ScsiCfgData to SpiCfgData structure,
then move all the raid related info into
new structure called RaidCfgData. This is
done because SAS supports RAID, as well as SPI,
so the raid stuff should be seperate.
* incorrect timeout calculation for cntdn
inside WaitForDoorbellAck and WaitForDoortbellInt
* add support for interpreting SAS Log Info
* Increase Event Log Size from 0xA to 0x32
* Fix bug in mptsas/mptfc/mptspi - when controller
has Initiator Mode Disabled, and only running in
TargetMode, the mptctl would panic when loading.
The fix is to return 0, instead of -ENODEV, in
SCSI LLD respective probe routines
* Fix bug in mptlan.c - driver will panic if
there is host reset, due to dev being set to
zero in mpt_lan_ioc_reset
* Fix's for SPI - Echo Buffer
* Several fix's in mptscsih_io_done - FCP Response
info, RESIDUAL_MISMATCH, Data Underrun, etc.
* Cleanup Error Handling - EH handlers,
mptscsih_flush_cmds, and zeroing out ScsiLookup
from mptscsih_qcmd
* Cleanup asyn event handling from
mptscsih -> mptscsih_event_process. Also
added support for SAS Persistent Table Full,
an asyn event
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- various bits for SAS support from the LSI driver.
- use the device private data for the fusion target private data.
this should be using the midlayer target data framework, but we
can't move over to that until fusion has been switched to the
generic DV code
- use target ID and channel from the fusion target private data,
because those in scsi_device will be different for mptsas
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Assorted endianess fixes. I'll work on full endianess annotations
later.
Acked by: Moore, Eric Dean <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert driver to use new change_queue_depth API.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Fixed up rejections and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Now we can change the pci core to always set this pointer, as pci drivers
should use it, not the driver core callback.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
