The code dealing with the 0 terminated meta_formats array is a bit klunky
especially for the uvc_meta_v4l2_enum_formats() case.
Instead of 0 terminating add an unsigned int nmeta_formats member to struct
uvc_device and use that. This leads to slightly cleaner code.
Signed-off-by: Hans de Goede <hansg@kernel.org>
Reviewed-by: Ricardo Ribalda <ribalda@chrium.org>
Tested-by: Ricardo Ribalda <ribalda@chromium.org> # Camera with MSXU_CONTROL_METADATA
Link: https://lore.kernel.org/r/20250708104622.73237-2-hansg@kernel.org
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
If the camera supports the MSXU_CONTROL_METADATA control, auto set the
MSXU_META quirk.
Reviewed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250707-uvc-meta-v8-5-ed17f8b1218b@chromium.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The UVC driver provides two metadata types V4L2_META_FMT_UVC, and
V4L2_META_FMT_D4XX. The only difference between the two of them is that
V4L2_META_FMT_UVC only copies PTS, SCR, size and flags, and
V4L2_META_FMT_D4XX copies the whole metadata section.
Now we only enable V4L2_META_FMT_D4XX for the Intel D4xx family of
devices, but it is useful to have the whole metadata payload for any
device where vendors include other metadata, such as the one described by
Microsoft:
https://learn.microsoft.com/en-us/windows-hardware/drivers/stream/mf-capture-metadata
This patch introduces a new format V4L2_META_FMT_UVC_MSXU_1_5, that is
identical to V4L2_META_FMT_D4XX.
Let the user enable this format with a quirk for now. This way they can
test if their devices provide useful metadata without rebuilding the
kernel. They can later contribute patches to auto-quirk their devices.
We will also work in methods to auto-detect devices compatible with this
new metadata format.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250707-uvc-meta-v8-4-ed17f8b1218b@chromium.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Right now, there driver supports devices with one or two metadata
formats. Prepare it to support more than two metadata formats.
This is achieved with the introduction of a new field `meta_formats`,
that contains the array of metadata formats supported by the device, in
the order expected by userspace.
Suggested-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250707-uvc-meta-v8-3-ed17f8b1218b@chromium.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The is_streaming field is used by modular PM to know if the device is
currently streaming or not.
With the transition to vb2 and fop helpers, we can use vb2 functions for
the same functionality. The great benefit is that vb2 already tracks the
streaming state for us.
Reviewed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250616-uvc-fop-v4-4-250286570ee7@chromium.org
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
When uvc was written the vb2 ioctl and file operation helpers didn't exist.
This patch switches uvc over to those helpers, which removes a lot of
boilerplate code and allows us to drop the 'privileges' scheme, since
that's now handled inside the vb2 helpers.
This makes it possible for uvc to fix the v4l2-compliance streaming tests:
warn: v4l2-test-formats.cpp(1075): Could not set fmt2
This patch introduces a change on behavior on the uvcdriver to be
aligned with the rest of the subsystem. Now S_INPUT, S_PARM and
S_FORMAT do no grant exclusive ownership of the device.
There are other side effects, some better than others:
- Locking is now more coarse than before, the queue is locked for almost
every ioctl.
- vidioc_querybuf() can now work when the queue is busy.
Future patches should look into the locking architecture of UVC to
remove one of stream->mutex or queue->mutex.
Reviewed-by: Hans de Goede <hansg@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Co-developed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250616-uvc-fop-v4-1-250286570ee7@chromium.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
To implement VIDIOC_QUERYCTRL, we need to know the minimum, maximum,
step and flags of the control. For some of the controls, this involves
querying the actual hardware.
Some non-compliant cameras produce errors when we query them. These
error can be triggered every time, sometimes, or when other controls do
not have the "right value". Right now, we populate that error to userspace.
When an error happens, the v4l2 framework does not copy the v4l2_queryctrl
struct to userspace. Also, userspace apps are not ready to handle any
other error than -EINVAL.
One of the main usecases of VIDIOC_QUERYCTRL is enumerating the controls
of a device. This is done using the V4L2_CTRL_FLAG_NEXT_CTRL flag. In
that usecase, a non-compliant control will make it almost impossible to
enumerate all controls of the device.
A control with an invalid max/min/step/flags is better than non being
able to enumerate the rest of the controls.
This patch:
- Retries for an extra attempt to read the control, to avoid spurious
errors. More attempts do not seem to produce better results in the
tested hardware.
- Makes VIDIOC_QUERYCTRL return 0 for -EIO errors.
- Introduces a warning in dmesg so we can have a trace of what has happened
and sets the V4L2_CTRL_FLAG_DISABLED.
- Makes sure we keep returning V4L2_CTRL_FLAG_DISABLED for all the next
attempts to query that control (other operations have the same
functionality as now).
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250502-uvc-eaccess-v8-1-0b8b58ac1142@chromium.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Most of the times that we have to call uvc_status_(get|put) we need to
call the usb_autopm_ functions.
Create a new pair of functions that automate this for us. This
simplifies the current code and future PM changes in the driver.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Message-ID: <20250327-uvc-granpower-ng-v6-2-35a2357ff348@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add a variable in the file handle state to figure out if a camera is in
the streaming state or not. This variable will be used in the future for
power management policies.
Now that we are at it, make use of guards to simplify the code.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Message-ID: <20250327-uvc-granpower-ng-v6-1-35a2357ff348@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The uvc_driver structure used to contain more fields, but those got
removed in commit ba2fa99668 ("[media] uvcvideo: Hardcode the
index/selector relationship for XU controls"). The structure is now just
a wrapper around usb_driver. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Implement support for ROI as described in UVC 1.5:
4.2.2.1.20 Digital Region of Interest (ROI) Control
ROI control is implemented using V4L2 control API as
two UVC-specific controls:
V4L2_CID_UVC_REGION_OF_INTEREST_RECT and
V4L2_CID_UVC_REGION_OF_INTEREST_AUTO.
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Yunke Cao <yunkec@google.com>
Reviewed-by: Yunke Cao <yunkec@google.com>
Tested-by: Yunke Cao <yunkec@google.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250203-uvc-roi-v17-16-5900a9fed613@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: fix control names: "Of" -> "of", "Controls" -> "Ctrls"]
v4l2_query_ext_ctrl contains information that is missing in
v4l2_queryctrl, like elem_size and elems.
With this change we can handle all the element_size information inside
uvc_ctrl.c.
Now that we are at it, remove the memset of the reserved fields, the
v4l2 ioctl handler should do that for us.
There is no functional change expected from this change.
Reviewed-by: Yunke Cao <yunkec@google.com>
Tested-by: Yunke Cao <yunkec@google.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250203-uvc-roi-v17-13-5900a9fed613@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
This patch adds support for compound controls. This is required to
support controls that cannot be represented with a s64 data, such as the
Region of Interest.
Signed-off-by: Yunke Cao <yunkec@google.com>
Tested-by: Yunke Cao <yunkec@google.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250203-uvc-roi-v17-10-5900a9fed613@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Right now, we only support mappings for v4l2 controls with a max size of
s32. This patch modifies the prototype of get/set so it can support any
size.
This is done to prepare for compound controls.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Yunke Cao <yunkec@google.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yunke Cao <yunkec@google.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250203-uvc-roi-v17-8-5900a9fed613@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
We want to support fetching the min and max values with g_ext_ctrls,
this patch is a preparation for that.
Instead of abusing uvc_query_v4l2_ctrl(), add an extra parameter to
uvc_ctrl_get, so it can support fetching the default value.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yunke Cao <yunkec@google.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250203-uvc-roi-v17-6-5900a9fed613@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Some cameras, such as the Sonix Technology Co. 292A, exhibit issues when
running two parallel streams, causing USB packets to be dropped when an
H.264 stream posts a keyframe while an MJPEG stream is running
simultaneously. This occasionally causes the driver to erroneously
output two consecutive JPEG images as a single frame.
To fix this, we inspect the buffer, and trigger a new frame when we
find an SOI.
Signed-off-by: Isaac Scott <isaac.scott@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20241128145144.61475-2-isaac.scott@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Right now the parameter value is read during video_registration and
cannot be changed afterwards, despite its permissions 0644, that makes
the user believe that the value can be written.
The parameter only affects the behaviour of uvc_queue_buffer_complete(),
with only one check per buffer.
We can read the value directly from uvc_queue_buffer_complete() and
therefore allowing changing it with sysfs on the fly.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241218-uvc-deprecate-v2-3-ab814139e983@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When an async control is written, we copy a pointer to the file handle
that started the operation. That pointer will be used when the device is
done. Which could be anytime in the future.
If the user closes that file descriptor, its structure will be freed,
and there will be one dangling pointer per pending async control, that
the driver will try to use.
Clean all the dangling pointers during release().
To avoid adding a performance penalty in the most common case (no async
operation), a counter has been introduced with some logic to make sure
that it is properly handled.
Cc: stable@vger.kernel.org
Fixes: e5225c820c ("media: uvcvideo: Send a control event when a Control Change interrupt arrives")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20241203-uvc-fix-async-v6-3-26c867231118@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We used the wrong device for the device managed functions. We used the
usb device, when we should be using the interface device.
If we unbind the driver from the usb interface, the cleanup functions
are never called. In our case, the IRQ is never disabled.
If an IRQ is triggered, it will try to access memory sections that are
already free, causing an OOPS.
We cannot use the function devm_request_threaded_irq here. The devm_*
clean functions may be called after the main structure is released by
uvc_delete.
Luckily this bug has small impact, as it is only affected by devices
with gpio units and the user has to unbind the device, a disconnect will
not trigger this error.
Cc: stable@vger.kernel.org
Fixes: 2886477ff9 ("media: uvcvideo: Implement UVC_EXT_GPIO_UNIT")
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20241106-uvc-crashrmmod-v6-1-fbf9781c6e83@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are two different use-cases of uvc_status():
- adding/removing a user when the camera is open/closed
- stopping/starting when the camera is suspended/resumed
Make the API reflect these two use-cases and move all the refcounting
and locking logic to the uvc_status.c file.
No functional change is expected from this patch.
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240926-guenter-mini-v7-1-690441953d4a@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
We do not have any quirk device making us of this. Remove from now. It
can be easily reverted later if needed.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
We can use heuristics to figure out the proper range of the control
instead of quirking every single device.
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Some advanced controls might not be completely implemented by vendors.
If the controls are a enumeration, UVC does not gives a way to probe
what is implemented and what is not.
Let's create a new callback function where heuristics can be implemented
to detect what is implemented and what not and update the control
mapping accordingly.
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
In UVC 1.5 we get a single clock value per frame. With the current
buffer size of 32, FPS slowers than 32 might roll-over twice.
The current code cannot handle two roll-over and provide invalid
timestamps.
Revome all the samples from the circular buffer that are more than two
rollovers old, so the algorithm always provides good timestamps.
Note that we are removing values that are more than one second old,
which means that there is enough distance between the two points that
we use for the interpolation to provide good values.
Tested-by: HungNien Chen <hn.chen@sunplusit.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240610-hwtimestamp-followup-v1-1-f9eaed7be7f0@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Logitech C922 internal SOF does not increases at a stable rate of 1kHz.
This causes that the device_sof and the host_sof run at different rates,
breaking the clock domain conversion algorithm. Eg:
30 (6) [-] none 30 614400 B 21.245557 21.395214 34.133 fps ts mono/SoE
31 (7) [-] none 31 614400 B 21.275327 21.427246 33.591 fps ts mono/SoE
32 (0) [-] none 32 614400 B 21.304739 21.459256 34.000 fps ts mono/SoE
33 (1) [-] none 33 614400 B 21.334324 21.495274 33.801 fps ts mono/SoE
* 34 (2) [-] none 34 614400 B 21.529237 21.527297 5.130 fps ts mono/SoE
* 35 (3) [-] none 35 614400 B 21.649416 21.559306 8.321 fps ts mono/SoE
36 (4) [-] none 36 614400 B 21.678789 21.595320 34.045 fps ts mono/SoE
...
99 (3) [-] none 99 614400 B 23.542226 23.696352 33.541 fps ts mono/SoE
100 (4) [-] none 100 614400 B 23.571578 23.728404 34.069 fps ts mono/SoE
101 (5) [-] none 101 614400 B 23.601425 23.760420 33.504 fps ts mono/SoE
* 102 (6) [-] none 102 614400 B 23.798324 23.796428 5.079 fps ts mono/SoE
* 103 (7) [-] none 103 614400 B 23.916271 23.828450 8.478 fps ts mono/SoE
104 (0) [-] none 104 614400 B 23.945720 23.860479 33.957 fps ts mono/SoE
Instead of disabling completely the hardware timestamping for such
hardware we take the assumption that the packet handling jitter is
under 2ms and use the host_sof as dev_sof.
We can think of the UVC hardware clock as a system with a coarse clock
(the SOF) and a fine clock (the PTS). The coarse clock can be replaced
with a clock on the same frequency, if the jitter of such clock is
smaller than its sampling rate. That way we can save some of the
precision of the fine clock.
To probe this point we have run three experiments on the Logitech C922.
On that experiment we run the camera at 33fps and we analyse the
difference in msec between a frame and its predecessor. If we display
the histogram of that value, a thinner histogram will mean a better
meassurement. The results for:
- original hw timestamp: https://ibb.co/D1HJJ4x
- pure software timestamp: https://ibb.co/QC9MgVK
- modified hw timestamp: https://ibb.co/8s9dBdk
This bug in the camera firmware has been confirmed by the vendor.
lsusb -v
Bus 001 Device 044: ID 046d:085c Logitech, Inc. C922 Pro Stream Webcam
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x046d Logitech, Inc.
idProduct 0x085c C922 Pro Stream Webcam
bcdDevice 0.16
iManufacturer 0
iProduct 2 C922 Pro Stream Webcam
iSerial 1 80B912DF
bNumConfigurations 1
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20240323-resend-hwtimestamp-v10-3-b08e590d97c7@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
When the device suspends, it keeps power-cycling.
The user notices it because the LED constanct oscillate between
blue (ready) and no LED (off).
<6>[95202.128542] usb 3-3-port4: attempt power cycle
<6>[95206.070120] usb 3-3.4: new high-speed USB device number 49 using xhci_hcd
<6>[95206.212027] usb 3-3.4: New USB device found, idVendor=2e1a, idProduct=4c01, bcdDevice= 2.00
<6>[95206.212044] usb 3-3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=<Serial: 1>
<6>[95206.212050] usb 3-3.4: Product: Insta360 Link
<6>[95206.212075] usb 3-3.4: Manufacturer: Amba
<7>[95206.214862] usb 3-3.4: GPIO lookup for consumer privacy
<7>[95206.214866] usb 3-3.4: using lookup tables for GPIO lookup
<7>[95206.214869] usb 3-3.4: No GPIO consumer privacy found
<6>[95206.214871] usb 3-3.4: Found UVC 1.10 device Insta360 Link (2e1a:4c01)
<3>[95206.217113] usb 3-3.4: Failed to query (GET_INFO) UVC control 14 on unit 1: -32 (exp. 1).
<3>[95206.217733] usb 3-3.4: Failed to query (GET_INFO) UVC control 16 on unit 1: -32 (exp. 1).
<4>[95206.223544] usb 3-3.4: Warning! Unlikely big volume range (=32767), cval->res is probably wrong.
<4>[95206.223554] usb 3-3.4: [9] FU [Mic Capture Volume] ch = 1, val = -32768/-1/1
<6>[95210.698990] usb 3-3.4: USB disconnect, device number 49
<6>[95211.963090] usb 3-3.4: new high-speed USB device number 50 using xhci_hcd
<6>[95212.657061] usb 3-3.4: new full-speed USB device number 51 using xhci_hcd
<3>[95212.783119] usb 3-3.4: device descriptor read/64, error -32
<3>[95213.015076] usb 3-3.4: device descriptor read/64, error -32
<6>[95213.120358] usb 3-3-port4: attempt power cycle
Bus 001 Device 009: ID 2e1a:4c01 Amba Insta360 Link
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x2e1a
idProduct 0x4c01
bcdDevice 2.00
iManufacturer 1 Amba
iProduct 2 Insta360 Link
iSerial 0
bNumConfigurations 1
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20221101-instal-v1-0-d13d1331c4b5@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Logitech Rally Bar devices, despite behaving as UVC cameras, have a
different power management system that the other cameras from Logitech.
USB_QUIRK_RESET_RESUME is applied to all the UVC cameras from Logitech
at the usb core. Unfortunately, USB_QUIRK_RESET_RESUME causes undesired
USB disconnects in the Rally Bar that make them completely unusable.
There is an open discussion about if we should fix this in the core or
add a quirk in the UVC driver. In order to enable this hardware, let's
land this patch first, and we can revert it later if there is a
different conclusion.
Fixes: e387ef5c47 ("usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Devinder Khroad <dkhroad@logitech.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20240404-rallybar-v6-1-6d67bb6b69af@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The formats, frames and intervals stored in the uvc_streaming structure
are not meant to change after being parsed at probe time. Make them
const to prevent unintended modifications, and adapt the probe code
accordingly to use non-const pointers during parsing.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The uvc_format 'frame' field points to an array of frames. Rename it to
'frames' to make this clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The uvc_streaming 'format' field points to an array of formats. Rename
it to 'formats' to make this clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
usb_kill_urb warranties that all the handlers are finished when it
returns, but does not protect against threads that might be handling
asynchronously the urb.
For UVC, the function uvc_ctrl_status_event_async() takes care of
control changes asynchronously.
If the code is executed in the following order:
CPU 0 CPU 1
===== =====
uvc_status_complete()
uvc_status_stop()
uvc_ctrl_status_event_work()
uvc_status_start() -> FAIL
Then uvc_status_start will keep failing and this error will be shown:
<4>[ 5.540139] URB 0000000000000000 submitted while active
drivers/usb/core/urb.c:378 usb_submit_urb+0x4c3/0x528
Let's improve the current situation, by not re-submiting the urb if
we are stopping the status event. Also process the queued work
(if any) during stop.
CPU 0 CPU 1
===== =====
uvc_status_complete()
uvc_status_stop()
uvc_status_start()
uvc_ctrl_status_event_work() -> FAIL
Hopefully, with the usb layer protection this should be enough to cover
all the cases.
Cc: stable@vger.kernel.org
Fixes: e5225c820c ("media: uvcvideo: Send a control event when a Control Change interrupt arrives")
Reviewed-by: Yunke Cao <yunkec@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of duplicating the menu info, use the one from the core.
Also, do not use extra memory for 1:1 mappings.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The device does not implement the power line frequenyc control
correctly. It is a UVC 1.5 device, but implements the control as a UVC
1.1 device.
Add the corresponding control mapping override.
Bus 003 Device 002: ID 30c9:0093 Lenovo Integrated Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x30c9
idProduct 0x0093
bcdDevice 0.07
iManufacturer 3 Lenovo
iProduct 1 Integrated Camera
iSerial 2 8SSC21J75356V1SR2830069
bNumConfigurations 1
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Move the control mapping to uvc_ctrl.c. This way we do not have
references to UVC controls or V4L2 controls in uvc_driver.c.
This also fixes a bug introduced in commit 382075604a ("media:
uvcvideo: Limit power line control for Quanta UVC Webcam"). The
offending commit caused the power line control menu entries to have
incorrect indices compared to the V4L2_CID_POWER_LINE_FREQUENCY_*
enumeration. Now that the limited mapping reuses the correct menu_info
array, the indices correctly map to the V4L2 control specification.
Fixes: 382075604a ("media: uvcvideo: Limit power line control for Quanta UVC Webcam")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Replace the count with a mask field that lets us choose not only the max
value, but also the minimum value and what values are valid in between.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Check for inactive controls in uvc_ctrl_is_accessible().
Use the new value for the master_id controls if present, otherwise
use the existing value to determine if it is OK to set the control.
Doing this here avoids attempting to set an inactive control, which
will return an error from the USB device, which returns an invalid
errorcode.
This fixes:
warn: v4l2-test-controls.cpp(483): s_ctrl returned EIO
warn: v4l2-test-controls.cpp(483): s_ctrl returned EIO
test VIDIOC_G/S_CTRL: OK
warn: v4l2-test-controls.cpp(739): s_ext_ctrls returned EIO
warn: v4l2-test-controls.cpp(739): s_ext_ctrls returned EIO
warn: v4l2-test-controls.cpp(816): s_ext_ctrls returned EIO
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
Tested with:
v4l2-ctl -c auto_exposure=1
OK
v4l2-ctl -c exposure_time_absolute=251
OK
v4l2-ctl -c auto_exposure=3
OK
v4l2-ctl -c exposure_time_absolute=251
VIDIOC_S_EXT_CTRLS: failed: Input/output error
exposure_time_absolute: Input/output error
ERROR
v4l2-ctl -c auto_exposure=3,exposure_time_absolute=251,auto_exposure=1
v4l2-ctl -C auto_exposure,exposure_time_absolute
auto_exposure: 1
exposure_time_absolute: 251
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Make the code more resilient, by replacing the castings with proper
structure definitions and using offsetof() instead of open coding the
location of the data.
Suggested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The V4L2 core overwrites format descriptions in v4l_fill_fmtdesc(),
there's no need to manually set the descriptions in the driver. This
prepares for removal of the format descriptions from the uvc_fmts table.
Unlike V4L2, UVC makes a distinction between the SD-DV, SDL-DV and HD-DV
formats. It also indicates whether the DV format uses 50Hz or 60Hz. This
information is parsed by the driver to construct a format name string
that is printed in a debug message, but serves no other purpose as V4L2
has a single V4L2_PIX_FMT_DV pixel format that covers all those cases.
As the information is available in the UVC descriptors, and thus
accessible to users with lsusb if they really care, don't log it in a
debug message and drop the format name string to simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The uvc_format_desc, GUID defines and the uvc_format_by_guid helper is
also useful for the uvc gadget stack. This patch moves them to a common
header.
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220909221335.15033-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions uvc_simplify_fraction and uvc_fraction_to_interval are
generic helpers which are also useful for other v4l2 drivers. This patch
moves them to v4l2-common.
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220909221335.15033-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices do not implement all their controls in a way that complies
with the UVC specification. This is for instance the case for several
devices that do not support the disabled mode for the power line
frequency control. Add a mechanism to allow per-device control mapping
overrides to avoid errors when accessing non-compliant controls.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The uvcvideo driver historically uses the
/* Comment
* style
*/
for multi-line block comments, which is frowned upon. Patches for the
driver are required to use the more standard
/*
* Comment
* style
*/
style. This result in inconsistencies. Fix it by converting all
remaining instances of the old style.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch aims to add UVC_GUID_FORMAT_H265
High Efficiency Video Coding (HEVC), also known as H.265 and MPEG-H Part 2.
They describe the same video encoding method.
So for handling their behavior is the same.
However, when external camera device describes this encoding method,
some use hevc, some use h265.
There is no uniform specification to describe this encoding method.
So if an external camera device use h265 to describe this encoding method,
driver will not recognize it.
Therefore, this patch is to enable driver to read HEVC/H265
and convert it to V4L2_PIX_FMT_HEVC.
Signed-off-by: James_Lin <Ping-lei.Lin@mediatek.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace manual decoding of psize in uvc_parse_streaming(), with the code
from uvc_endpoint_max_bpi(). It also handles usb3 devices.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Some uvc devices appear to require the maximum allowed USB timeout
for GET_CUR/SET_CUR requests.
So lets just bump the UVC control timeout to 5 seconds which is the
same as the usb ctrl get/set defaults:
USB_CTRL_GET_TIMEOUT 5000
USB_CTRL_SET_TIMEOUT 5000
It fixes the following runtime warnings:
Failed to query (GET_CUR) UVC control 11 on unit 2: -110 (exp. 1).
Failed to query (SET_CUR) UVC control 3 on unit 2: -110 (exp. 2).
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If we have an error setting a control, return the affected control in
the error_idx field.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We can figure out if reading/writing a set of controls can fail without
accessing them by checking their flags.
This way we can honor the API closer:
If an error is found when validating the list of controls passed with
VIDIOC_G_EXT_CTRLS, then error_idx shall be set to ctrls->count to
indicate to userspace that no actual hardware was touched.
Fixes v4l2-compliance:
Control ioctls (Input 0):
warn: v4l2-test-controls.cpp(765): g_ext_ctrls(0) invalid error_idx 0
fail: v4l2-test-controls.cpp(645): invalid error index write only control
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The framework already contains a map of IDs to names, lets use it when
possible.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans has discovered that in his test device, for the H264 format
bytesused goes up to about 570, for YUYV it will actually go up
to a bit over 5000 bytes, and for MJPG up to about 2706 bytes.
We should also, according to V4L2_META_FMT_UVC docs, drop headers when
the buffer is full.
Credit-to: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
