Add multiplexed streams support. CAL has 8 DMA-engines and can capture 8
separate streams at the same time. The driver filters the streams based
on CSI-2 virtual channel number and datatype. CAL may have (depending on
the SoC) two CSI-2 RX blocks, which share the 8 DMA-engines, so the
number of capturable streams does not change even if there are two CSI-2
RX blocks.
Add 8 video device nodes, each representing a single DMA-engine, and set
the number of source pads on CSI-2 RX blocks to 8. Each video node can be
connected to any of the source pads on either of the CSI-2 RX instances
using media links. CSI-2 RX block's subdevice internal routing is used
to route the incoming CSI-2 streams to one of the 8 source pads.
Only video data streams are supported at the moment.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Call v4l2_get_link_freq() on a pad, instead of a control handler. This way
we can soon convert v4l2_get_link_freq() to be callable only on a pad and
remove the compatibility code.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Naushir Patuck <naush@raspberrypi.com> # rp1-cfe
Acked-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com> # st-mipid02
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
CAL uses get_frame_desc to get the VC and DT for the incoming CSI-2
stream, but does it in a bit hacky way. Clean this up by implementing
.get_frame_desc to camera-rx, and calling that from cal.c.
No functional change intended.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Change TI CAL driver to use subdev state. No functional changes
(intended).
This allows us to get rid of the 'formats' field, as the formats are
kept in the state, and also the 'mutex' as we already have state locking.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use video_device_pipeline_alloc_start() instead of manually
allocating/managing the media pipeline storage.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The userspace needs a way to match received metadata buffers to pixel
data buffers. The obvious way to do this is to use the CSI-2 frame
number, as both the metadata and the pixel data have the same frame
number as they come from the same frame.
However, we don't have means to convey the frame number to userspace. We
do have the 'sequence' field, which with a few tricks can be used for
this purpose.
To achieve this, track the frame number for each virtual channel and
increase the sequence for each virtual channel by frame-number -
previous-frame-number, also taking into account the eventual wrap of the
CSI-2 frame number. If the CSI-2 peripheral does not support frame
numbers, CAL increases the frame number register by one each frame.
This way we get a monotonically increasing sequence number which is
common to all streams using the same virtual channel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use get_frame_desc() to get the frame desc from the connected source,
and use the provided virtual channel and datatype instead of hardcoded
ones.
get_frame_desc() can contain multiple streams, but as we don't support
multiple streams yet, we will just always use the first stream.
If the source doesn't support get_frame_desc(), fall back to the
previous method of always capturing virtual channel 0 and any datatype.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ti-vpe/ sub-directory does not only contain the VPE-specific things.
It also contains the CAL driver, which is a completely different
subsystem. This is also not a good place to add new drivers for other TI
platforms since they will all get mixed up.
Separate the VPE and CAL parts into different sub-directories and rename
the ti-vpe/ sub-directory to ti/. This is now the place where new TI
platform drivers can be added.
[mchehab: rebased to apple on the top of media/platform/Kconfig series]
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
