The IRQ handler rkisp1_isr() calls sub-handlers, all of which returns an
irqreturn_t value, but rkisp1_isr() ignores those values and always
returns IRQ_HANDLED.
Fix this by collecting the return values, and returning IRQ_HANDLED or
IRQ_NONE as appropriate.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-2-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In all known platforms the ISP has dedicated IRQ lines, but for some
reason the driver uses IRQF_SHARED.
Supporting IRQF_SHARED properly requires handling interrupts even when
our device is disabled, and the driver does not handle this. To avoid
adding such code, and to be sure the driver won't accidentally be used
in a platform with shared interrupts, let's drop the IRQF_SHARED flag.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-1-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for the multi-planar variants of NV12. The RGA is now able
to exchange DMABUFs with other devices that only support multi-planar
NV12, for example the Hantro JPEG encoder.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Multi-planar formats may have multiple planes that must be handled and
correctly mapped into a continuous buffer for the RGA by using the DMA
descriptors.
The plane offsets in the continuous mapping may now start at page
boundaries and the previous calculation based on the frame sizes is only
valid for planar buffers in a single memory. Therefore, the offsets must
be detected and set while creating the mapping.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Switch to the multi-planar API, which allows to handle buffers with
separate planes.
The RGA driver doesn't expose multi-planar formats, yet. The existing
contiguous planar formats can be used with the multi-planar API as well,
but the multi-planar API is required for multi-planar formats.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the provided V4L2_TYPE_IS_{OUTPUT,CAPTURE} macros to check if the
buffer or queue is OUTPUT or CAPTURE. The macros work also work for the
_MPLANE buffer and queue types and make it easier to switch to the
multi-planar API.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The local variable allows to simplify the accessed to the format and
makes it easier to change the type of the format.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the pixelformat instead of the v4l2_format to find the rga_fmt. This
avoids knowing the structure and type of v4l2_format in rga_fmt_find and
simplifies the function.
Also cleanup the users of the function. In try_fmt always return the
found pixel format to make sure that the pixel format is always set.
Thus, we can be sure that we will find the rga_fmt in s_fmt and can drop
the check if a given format has been found.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The try_fmt should limit the width and height to the know limits of the
RGA. Use the clamp() helper instead of open coding the clamping.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The RGA DMA descriptor list contains only 32-bit addresses. Set the
dma_mask to only allocate memory that is addressable by the descriptors.
This prevents errors when preparing vb2 buffers that were allocated by
the RGA.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Calculate the plane offsets and store them with the video buffer while
creating the buffer mapping.
This allows the driver to more freely handle the memory of the DMA
mapping as the offsets and the mapping can be kept in sync.
The driver still has to update the offsets to respect the configured
cropping and rotation, but this calculation is now separated from the
calculation of the plane offsets.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Split the register setup for the source and destination video buffers
into separate functions.
This is a cleanup to make the code more readable by separating the
offset calculation for the different buffers and prepares the driver for
using pre-calculated offsets of planes.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The RGA driver allocates two buffers for the DMA descriptors of the
input and output buffers. Whenever a new job is processed, the
descriptor list is updated for the current buffers.
By updating the descriptor list during buf_prepare, it is possible to
correctly fail DMABUF imports if the buffers that shall be imported are
not within the 32 bit address range that can be addressed by the RGA.
Managing the DMA descriptor list with the buffer also makes it easier to
track the buffer mapping and the plane offsets into this mapping.
The cost is that the driver now requires DMA coherent memory per buffer
for the descriptor list. However, the size scales with the size of the
video buffers and is not allocated if the RGA is not used.
While at it, use dma_alloc_coherent to allocate the descriptors and get
rid of the virt_to_phys calls to get the physical addresses.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The IOMMU of the RGA is programmed with a list of DMA descriptors that
contain an 32 bit address per 4k page in the video buffers. The address
in the descriptor points to the start address of the page.
Introduce 'struct rga_dma_desc' to make the handling of the DMA
descriptors explicit instead of hiding them behind standard types.
While at it, use provided helpers for iterating the sg_table instead of
manually calculating the DMA addresses.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When using 32 bit RGB formats, the RGA on the rk3568 produces wrong
colors as the wrong color channels are read or written. The reason is
that the format description for the channel swizzeling is wrong and the
wrong bits are configured. For example, when converting ARGB32 to NV12,
the alpha channel is used as blue channel.. This doesn't happen if the
color format is the same on both sides.
Fix the color_swap settings of the formats to correctly handle 32 bit
RGB formats.
For RGA_COLOR_FMT_XBGR8888, the RGA_COLOR_ALPHA_SWAP bit doesn't have an
effect. Thus, it isn't possible to handle the V4L2_PIX_FMT_XRGB32. Thus,
it is removed from the list of supported formats.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .init_cfg() operation is affected by two issues:
- It has long been extended to initialize a whole v4l2_subdev_state
instead of just a v4l2_subdev_pad_config, but its name has stuck
around.
- Despite operating on a whole subdev state and not being directly
exposed to the subdev users (either in-kernel or through the userspace
API), .init_cfg() is categorized as a subdev pad operation.
This participates in making the subdev API confusing for new developers.
Fix it by renaming the operation to .init_state(), and make it a subdev
internal operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net> # for imx415
Acked-by: Shuah Khan <skhan@linuxfoundation.org> # for vimc
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[Sakari Ailus: Resolved a conflict in Renesas vsp1 driver.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The resizer is used to scale the image, but also to change the
subsampling of YUV formats. Both the luma and chroma dimensions need to
be taken into account to decide whether or not to enable the resizer.
The current implementation disables the resizer if the chroma vertical
size isn't changed, which would be the case when scaling up by a factor
of 2 vertically while at the same time converting from YUV 4:2:2 to
4:2:0. Fix it by checking the luma sizes too.
While at it, reflow and clarify comments in the function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The debug messages that show the resizer configuration are only printed
if the driver enables the resizer. This prevents checking the resizer
configuration when the driver believes it should be disabled. Fix it by
moving the dev_dbg() statements earlier.
Also, combine the two debug prints into a single one to gather all the
information in one place, which makes reading the log easier.
While at it, use %u instead of %d to print unsigned values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The sink_y local variable in rkisp1_rsz_config() stores a copy of the
sink_crop crop rectangle. Drop it, and rename sink_crop to sink_y.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The rkisp1_rsz_config() and rkisp1_rsz_config_regs() functions use a
v4l2_rect to pass frame sizes, leaving the top and left members unused
and uninitialized. Use v4l2_area instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Pointers to v4l2_mbus_framefmt and v4l2_rect instances don't need to be
modified when configuring the resizer. Make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The self path has a Y_PIC_SIZE register that needs to be programmed to
the total number of pixels, including the stride. This isn't done by the
driver, fix it.
While at it, reorder the register write order to sort them by address.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The dual crop register is the same for both the MP and SP channels. Drop
it from the rkisp1_rsz_config structure and use the
RKISP1_CIF_DUAL_CROP_CTRL macro directly in the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The line stride is expressed in the hardware as a number of pixels for
the first plane. The bytesperline must thus be a multiple of the first
plane's bpp value. Enforce this constraint.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The rkisp1_v12_params_ops global variable doesn't need to be modified.
Make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Hex constants in the media subsystem are typically in lowercase. The
rkisp1 driver mostly follows that convention already, except in the
register definitions. Convert all hex constants to lowercase for
consistency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the V4L2 subdev active state API to store the active format and crop
rectangle. This simplifies the driver not only by dropping the state
stored in the rkisp1_csi structure, but also by replacing the ops_lock
with the state lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the V4L2 subdev active state API to store the active format and crop
rectangle. This simplifies the driver not only by dropping the state
stored in the rkisp1_isp structure, but also by replacing the ops_lock
with the state lock.
The rkisp1_isp.sink_fmt field needs to be kept, as it is accessed from
the stats interrupt handler. To simplify the rkisp1_isp_set_sink_fmt()
implementation, the field is now set when starting the ISP, instead of
when setting the format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the V4L2 subdev active state API to store the active format and crop
rectangle. This simplifies the driver not only by dropping the state
stored in the rkisp1_resizer structure, but also by replacing the
ops_lock with the state lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Set the v4l2_device already in async notifier init, so struct device
related to it will be available before the notifier is registered. This
requires separating notifier initialisation into two functions, one that
takes v4l2_device as its argument, v4l2_async_nf_init and
v4l2_async_subdev_nf_init, for sub-device notifiers. Registering the
notifier will use a single function, v4l2_async_nf_register.
This is done in order to make struct device available earlier, during
construction of the async connections, for sensible debug prints.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add v4l2_async_connection_unique() function for obtaining a struct
v4l2_async_connection, typically allocated by drivers together with their
own information on an external sub-device.
The relation between connections and sub-devices still remains 1:1 but
this code becomes more complex when the relation soon changes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Rename v4l2_async_subdev as v4l2_async_connection, in order to
differentiate between the sub-devices and their connections: one
sub-device can have many connections but the V4L2 async framework has so
far allowed just a single one. Connections in this context will later
translate into either MC ancillary or data links.
This patch prepares changing that relation by changing existing users of
v4l2_async_subdev to switch to v4l2_async_connection. Async sub-devices
themselves will not be needed anymore
Additionally, __v4l2_async_nf_add_subdev() has been renamed
__v4l2_async_nf_add_connection().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fix this smatch warning:
drivers/media/platform/rockchip/rga/rga.c:734 rga_enable_clocks() warn: 'rga->sclk' from clk_prepare_enable() not released on lines: 734.
The reason is that aclk should be disabled/unprepared before
sclk, instead of the other way around.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Jacob Chen <jacob-chen@iotwrt.com>
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The v4l2_m2m_buf_copy_metadata function correctly copies the metadata of
the buffer. Use that function instead of open-coding the metadata copy.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Commit 0d346d2a6f ("media: v4l2-subdev: add subdev-wide state struct")
applied a large media tree-wide change produced by coccinelle. It was so
large that a set of identical indentation issues went unnoticed during
review. Fix them.
While at it, and because it's easy to review both changes together, add
a trailing comma for the last (and only) struct member initialization of
the related structures, to avoid future changes should new fields need
to be initialized.
Fixes: 0d346d2a6f ("media: v4l2-subdev: add subdev-wide state struct")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add support for NV16M and NV61M as output formats. As NV16, NV61, NV12M
and NV21M are already supported, the infrastructure is already in place
to support NV16M and NV61M, so it is sufficient to simply add relevant
entries to the list of output formats.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Don't populate the const arrays on the stack, instead make them
static. Also makes the object code smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't populate the const arrays on the stack, instead make them
static. Also makes the object code smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Convert the media drivers to use video device based pipeline start/stop
where possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
'streaming_count' is a bit misleading name, as the count is increased
with media_pipeline_start(). Let's rename it to 'start_count' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The local sd_fmt variable in rkisp1_capture_link_validate() has
uninitialized fields, which causes random failures when calling the
subdev .get_fmt() operation. Fix it by initializing the variable when
declaring it, which zeros all other fields.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISP8000Nano v18.02 (found in the i.MX8MP) requires the ISP to be
enabled (as indicated by the ISP_CTRL.ISP_ENABLE bit) to configure the
lens shading table in internal RAM. The driver currently configures all
ISP initial parameters before enabling the ISP, which causes the LSC RAM
to not be initialized properly.
To fix this, split the rkisp1_params_configure() function into a
rkisp1_params_pre_configure() and a rkisp1_params_post_configure(). The
former configures all ISP parameters but LSC, while the latter
configures LSC. To implement this, the rkisp1_params_apply_params_cfg()
function is deconstructed, with two small helpers created to deal with
the parameters buffers, which are then used in rkisp1_params_isr(),
rkisp1_params_pre_configure() and rkisp1_params_post_configure().
While this initialization ordering is only needed for the ISP8000Nano
v18.02, it doesn't affect other ISP versions negatively, and can thus be
followed unconditionally.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_lsc_config() function incorrectly uses the
RKISP1_CIF_ISP_LSC_SECT_SIZE() macro for the gradient registers. Replace
it with the correct macro, and rename it from
RKISP1_CIF_ISP_LSC_GRAD_SIZE() to RKISP1_CIF_ISP_LSC_SECT_GRAD() as the
corresponding registers store the gradients for each sector, not a size.
This doesn't cause any functional change as the two macros are defined
identically (the size and gradient registers store fields in the same
number of bits at the same positions).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The LSC module x/y size and grad configuration is stored in a set of 4
indexed registers each. The rkisp1-regs.h header defines all those
registers, but only the first one in each set is used, with manual
calculation of addresses of subsequent registers. Simplifies this by
merging all 4 register macros into one that takes the index as a
parameter. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the u32 type instead of unsigned int to store register values in the
LSC configuration code, to make the variables' size more explicit. No
functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Clean up the LSC configuration code to improve its readability by
shortening lines, using extra local variables and renaming long
variables. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The resizer doesn't deal with color spaces, so it can accept any color
space on its input, and propagates it unchanged to its output. When
operating with a Bayer input format (in pass-through mode) further
restrict the YCbCr encoding and quantization to Rec 601 and full range
respectively, as for raw data the former ought to be ignored and the
latter is always full range.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Initialize the four color space fields on the sink and source video pads
of the resizer in the .init_cfg() operation. The resizer can't perform
any color space conversion, so set the sink and source color spaces to
the same defaults, which match the ISP source video pad default.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver currently only implements the Rec. 601 YCbCr encoding, extend
it with support for the other encodings defined by V4L2 (Rec. 709, Rec.
2020 and SMPTE240m). The coefficients have been calculated by rounding
the floating point values to the nearest Q1.7 fixed-point value,
adjusting the rounding to ensure that the sum of each line in the matrix
is preserved to avoid overflows.
At the hardware level, the RGB to YUV conversion matrix is fully
configurable, custom encoding could be supported by extending the ISP
parameters if desired.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_csm_config() function takes a pointer to the rkisp1_params
structure which contains the quantization value. There's no need to pass
it separately to the function. Drop it from the function parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_config_isp() function uses the format on the sink pad of the
ISP to configure quantization at the output of the ISP. This is
incorrect, as hinted by the src_frm variable name that stores the
format. Fix it by using the source pad.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISP output color space is configured through the ISP source pad. At
the moment, only the quantization can be set. Extend it to the three
other color space fields:
- The ycbcr_enc field will be used to configure the RGB to YUV matrix
(currently hardcoded to Rec. 601).
- The colorspace (which controls the color primaries) and xfer_func
fields will not be used to configure the ISP, as the corresponding
hardware blocks (the cross-talk RGB to RGB matrix and the tone mapping
curve) are programmed directly by applications through ISP parameters.
Nonetheless, those two fields should be set by applications to match
the ISP configuration, in order to propagate the correct color space
down the pipeline up to the capture video nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISP converts Bayer data to YUV when operating normally, and can also
operate in pass-through mode where the input and output formats must
match. Converting from YUV to Bayer isn't possible. If such an invalid
configuration is attempted, adjust it by copying the sink pad media bus
code to the source pad.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISP accepts different color spaces on its input: for YUV input, it
doesn't set any restrictions, and for Bayer inputs, any color primaries
or transfer function can be accepted (YCbCr encoding isn't applicable
there, and quantization range can only be full).
Allow setting a color space on the ISP sink pad, with the aforementioned
restrictions. The settings don't influence hardware yet (only the YUV
quantization range will, anything else has no direct effect on the ISP
configuration), but can already be set to allow color space information
to be coherent across the ISP sink link.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Initialize the four color space fields on the sink and source video pads
of the ISP in the .init_cfg() operation. As the main use case for the
ISP is to convert Bayer data to YUV, select a raw color space on the
sink pad and a limited range quantization of SYCC on the source pad by
default.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Extend the UAPI rkisp1-config.h header with macros for all DPCC
configuration fields. While at it, clarify of fix issues in the DPCC
documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Restrict the DPCC configuration that can be set by userspace to valid
register bits. To do so, reorganize the related register macros to
define valid bitmasks, as well as bits of the DPCC mode register.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_dpcc_config() function looks over methods sets to configure
them, but sets the RKISP1_CIF_ISP_DPCC_METHODS_SET_* registers outside
of the loop with hand-unrolled code. Move this to the loop to simplify
the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
rga_parse_dt is missing a error return, so if some of the resources
return DEFER_PROBE, probe will succeed without these resources.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Co-developed-by: Jarrah Gosbell <kernel@undef.tools>
Signed-off-by: Jarrah Gosbell <kernel@undef.tools>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a register dump file in debugfs for some of the buffer-related
registers for the main path in MI (for the base address, the size, and
the offset). Also dump the corresponding shadow registers.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Different ISP versions implement different sets of features. The driver
already takes the version into account in several places, but this
approach won't scale well for features that are found in different
versions. Introduce a new mechanism using a features bitmask in the
rkisp1_info structure to indicate which features the ISP support.
The first feature bit tells if the ISP has an internal CSI-2 receiver,
which is not available in all ISP versions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISP has a parallel input, exposed through port 1 in the device tree
node. While the driver supports configuring the ISP for the parallel and
BT.656 input modes, the DT parsing code, the subdev bound handler and
the ISP stream start handler only support the CSI input. Extend them to
support the parallel input.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When registering the notifier, replace the manual while loop with
fwnode_graph_for_each_endpoint. This simplifies error handling.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Connect the CSI receiver subdevice between the sensors and the ISP. This
includes:
- Calling the subdevice via the v4l2 subdev API
- Moving the async notifier for the sensor from the ISP to the CSI
receiver
- In the ISP, create a media link to the CSI receiver, and remove the
media link creation to the sensor
- In the CSI receiver, create a media link to the sensor
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The CSI receiver is a component separate from the ISP or the resizers.
It is actually optional, not all device model include a CSI receiver. On
some SoCs CSI-2 support can be provided through an external CSI-2
receiver, connected to the ISP's parallel input.
To support those use cases, create a V4L2 subdev to model the CSI
receiver. It will allow the driver to handle both internal and external
CSI receivers the same way.
The next commit will plumb the CSI subdev to the rest of the driver,
replacing direct function calls.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISP supports multiple source subdevs, but can only capture from a
single one at a time. The source is selected through link setup. The
driver finds the active source in its .s_stream() handler using the
media_entity_remote_pad() function. This fails to reject invalid
configurations with multiple active sources. Fix it by using the
media_pad_remote_pad_unique() helper instead, and inline
rkisp1_isp_get_source() in rkisp1_isp_s_stream() as the function is
small and has a single caller.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Rename the rkisp1_get_remote_source() function to
rkisp1_isp_get_source() to use a consistent rkisp1_isp_* prefix for all
ISP functions, and drop the "remote" as the source can't be local.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A set of local variables point to structure that are not meant to be
modified. Constify them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Initialize the src_fmt and sink_fmt variable when declaring them in
rkisp1_config_isp().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_config_isp() function stores the value of the input selection
and polarity configuration in two different local variables, OR'ed
together when writing the register. Merge them into a single acq_prop
variable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISP_ACQ_PROP register is set twice, once in rkisp1_config_isp() for
most of its fields, and once in rkisp1_config_dvp() (called from
rkisp1_config_path()) to configure the input selection field. Move the
latter to rkisp1_config_isp() to write the register once only, and drop
the now empty rkisp1_config_dvp() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace the rkisp1_device pointer argument to the internal functions of
the ISP implementation with a rkisp1_isp object. This makes the code
flow more logical, as the functions operate on the ISP object.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_isp structure documentation mentions a backpointer field to
rkisp1_device, but the field is missing. Add it, and use it to replace
more complicated constructs using container_of() on the v4l2_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The active_sensor field of the rkisp1_device structure points to the ASD
data for the active source. The source may however not be a sensor, so
the naming is a bit confusing. Furthermore, the driver doesn't need to
access the full ASD from the active_sensor field, only the subdev
pointer is needed, when stopping streaming.
Rename the field to source, and turn it into a v4l2_subdev pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To prepare for the removal of the active_sensor field from the
rkisp1_device structure, pass the media bus type of flag to the
rkisp1_config_cif() function instead of accessing them through
active_sensor.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ret variable doesn't need to be initialized in
rkisp1_isp_s_stream().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor argument to rkisp1_csi_start() isn't meant to be modified by
the function. Make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To prepare for the removal of the active_sensor field from the
rkisp1_device structure, pass the sensor pointer to the
rkisp1_csi_config() function instead of accessing it through
active_sensor.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The delay in rkisp1_isp_start() is related to the CSI-2 receiver and
the camera sensor. Move it where it belongs, to rkisp1_csi_start().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The CSI-related functions are not named consistently. Fix it by using a
common rkisp1_csi prefix.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISP layer now calls multiple functions of the CSI-2 RX layer to
configure, start and stop it, with the steps for the last two
operations. Move those calls to rkisp1_mipi_csi2_start() and
rkisp1_mipi_csi2_stop() to simplify the ISP code and the API exposed by
the CSI-2 receiver component.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make sure the ISP is ready to receive data before starting the CSI-2
receiver by starting it first. Similarly, stop the CSI-2 receiver before
the ISP when stopping streaming.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Not all ISP instances include a MIPI CSI-2 receiver. To prepare for
making it optional, move code related to the CSI-2 receiver to a
separate file.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When a sensor is bound, its source pad is retrieved in the .bound()
operation with a call to media_entity_get_fwnode_pad(). The function
should be called with the source endpoint fwnode of the sensor, but is
instead called with the sensor's device fwnode.
Fix this, which involves storing a reference to the source endpoint
fwnode in the rkisp1_sensor_async structure, and thus implementing the
subdev notifier .destroy() operation to release the reference.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The function name isn't very clear, rename it to
rkisp1_subdev_notifier_register().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There's no need to wait until all async subdevs are bound before
creating internal links. Create them at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Links from sensors to the ISP can be created as sensors are bound. Move
the link creation from rkisp1_create_links() to the bound notifier, and
clean up the rkisp1_create_links() function while at it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1 driver requires the sensor to implement the pixel rate
control. Trying to operate without it will cause an error when starting
streaming. Catch the issue earlier, at bound time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the calls to the active sensor's .s_stream() operation to the ISP
subdev's .s_stream(). This groups all handling of the active sensor in
one place, preparing for a rework of that code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When a link validation failure occurs, print a debug message to help
diagnosing the cause.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
