A recent commit refactored the printing of the CSID hardware version, but
(without it being mentioned) also changed the log level from debug to
info.
This results in repeated log spam during use, for example, on the Lenovo
ThinkPad X13s:
qcom-camss ac5a000.camss: CSID:0 HW Version = 1.0.0
qcom-camss ac5a000.camss: CSID:0 HW Version = 1.0.0
qcom-camss ac5a000.camss: CSID:0 HW Version = 1.0.0
qcom-camss ac5a000.camss: CSID:0 HW Version = 1.0.0
qcom-camss ac5a000.camss: CSID:0 HW Version = 1.0.0
Suppress the version logging by demoting to debug level again.
Fixes: f759b8fd30 ("media: qcom: camss: csid: Move common code into csid core")
Cc: stable@vger.kernel.org
Cc: Depeng Shao <quic_depengs@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Remove redefined image data type IDs taken directly from the MIPI CSI-2
specification. Non-functional change.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
There is no CSID TPG on some SoCs, so the v4l2 ctrl in CSID driver
shouldn't be registered. Checking the supported TPG modes to indicate
if the TPG hardware exists or not and only registering v4l2 ctrl for
CSID only when the TPG hardware is present.
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The get hw version and src pad code functions can be common code in csid
core file, then the csid driver of different hw version can reuse them,
rather than adding duplicate code in csid driver for each version.
Suggested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Decouple the direct calls to VFE's vfe_get/put in the CSID subdev
in order to prepare for the introduction of IFE subdev.
Also decouple CSID base address from VFE since on the Titan platform
CSID register base address resides within VFE's base address.
Signed-off-by: Milen Mitkov <quic_mmitkov@quicinc.com>
Signed-off-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # sc8280xp/sm8250/sdm845/apq8016
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Following the example of VFE, move all formats of the decoder
to camss-csid.c and attach them to the subdevices resources.
Signed-off-by: Radoslav Tsvetkov <quic_rtsvetko@quicinc.com>
Signed-off-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # sc8280xp/sm8250/sdm845/apq8016
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Currently resources structure grows with additional parameters required for
each sub-deivce. However each sub-device has some specific resources or
configurations which need to be passed during the initialization.
This change adds per sub-device type structure to simplify the things
and removes the magical void pointer to hw_ops.
Signed-off-by: Radoslav Tsvetkov <quic_rtsvetko@quicinc.com>
Signed-off-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # sc8280xp/sm8250/sdm845/apq8016
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some platforms such as SC7280 have 3 CSIDs and 2 CSID-lites but current
code has hardcoded 2 as the maximum number of CSIDs. Remove the hardcoded
maximum number of VFEs to handle all possible combinations of CSIDs and
CSID-lites.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
V4L2 subdev operations have moved from operating on a
v4l2_subdev_pad_config to a v4l2_subdev_state a long time ago. Fix
remaining incorrect references to pad config in comments.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
From sdm845 onwards we need to ensure the VFE is powered on prior to
switching on the CSID.
Currently the code tests for sdm845, sm8250 and then does get/set. This is
not extensible and it turns out is not necessary either since vfe_get and
vfe_set reference count.
Remove the over-conservative SoC version check.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # rb3 # db410c
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
It is possible to pass all of the CAMSS subdevice internal operations
pointers from the controlling resources structure with an additional
pointer added to the resources structure.
This allows for the removal of most of the probe-time control structures.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The following variables are being assigned statically based on
compatible strings in the probe path.
* enum camss_version version;
* unsigned int csiphy_num;
* unsigned int csid_num;
* unsigned int vfe_num;
* unsigned int vfe_lite_num;
* unsigned int vfe_total_num;
Migrate those variables to resource parameters passed in on platform
probe arguments. The one caveat is for VFE it has been necessary to
intoduce a new variable vfe_total_num to capture the aggregate value of
vfe_num + vfe_lite_num.
All the rest of the changes are rote camss->variable to
camss->res->variable with the parameter tables now populating the listed
variables.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rename non-specific struct resources {} to struct camss_subdev_resources {}
Each logical block in CAMSS has a number of regulators, clocks and resets
associated with it. We represent these blocks as v4l subdevices.
The name "struct camss_subdev_resources" is a more descriptive and accurate
name.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Platforms with qcom-camss use CSI-2, which means 1X16 is more correct
than 2X8. The fact that qcom-camss supported only 2X8 meant it was
incompatible with camera sensors it should have been compatible with.
For example, the ov5645 driver (correctly) reports that its format is
UYVY8_1X16 (after ba449bb562).
Since qcom-camss only supports 2X8, the qcom-camss system is
incompatible with the ov5645 driver, even though they should be
compatible.
This patch replaces all uses of UYVY8_2X8/VYUY8_2X8/YUYV8_2X8/YVYU8_2X8
with the equivalent 1X16 formats.
Signed-off-by: Martin Dørum <dorum@noisolation.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
CSID hardware on SM8250 can demux up to 4 simultaneous streams
based on virtual channel (vc) or datatype (dt).
The CSID subdevice entity now has 4 source ports that can be
enabled/disabled and thus can control which virtual channels
are enabled. Datatype demuxing not tested.
In order to keep a valid internal state of the subdevice,
implicit format propagation from the sink to the source pads
has been preserved. However, the format on each source pad
can be different and in that case it must be configured explicitly.
CSID's s_stream is called when any stream is started or stopped.
It will call configure_streams() that will rewrite IRQ settings to HW.
When multiple streams are running simultaneously there is an issue
when writing IRQ settings for one stream while another is still
running, thus avoid re-writing settings if they were not changed
in link setup, or by fully powering off the CSID hardware.
Signed-off-by: Milen Mitkov <quic_mmitkov@quicinc.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The media_entity_remote_pad() is misnamed, as it operates on a pad and
not an entity. Rename it to media_pad_remote_pad_first() to clarify its
behaviour.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
'supplies' is a pointer, the real size of struct regulator_bulk_data
should be pass to devm_kmalloc_array().
Fixes: 0d81401797 ("media: camss: Add regulator_bulk support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the ability to enable or disable multiple regulators in bulk with
camss. This is useful for sm8250, sdm845 and it looks like sdm660 where we
have more than one CSI regulator to do at once.
It should just work for standalone existing vdda regulators and parts which
don't have an explicitly defined CSI regulator.
[hverkuil: fix camss-csid.c:163:13: warning: 'ret' may be used uninitialized in this function]
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Similar to the SM8250 the CSID relies on the VFE to be clocked prior to
taking the CSID out of reset.
Apply the same fixup to SDM845 as SM8250.
Suggested-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sm8250 CAMSS CSID depends on the VFE it is attached to being powered on
and clocked prior to taking the CSID out of reset.
It is possible to open just the CSID subdev from libcamera and attempt to
bring the CSID block up.
If we do not first bring up the VFE the CSID will fail to come out of
reset.
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Titan 480 camss found on SM8250 has 6 CSIPHY and 4 VFE/CSID.
CSID is compatible with the Titan 170 CSID, but the Titan 480 CSID are
inside the VFE region (between the "top" and "bus" registers), so a
workaround is added to avoid ioremap failure.
[bod] Fixed setting camnoc_axi_clk_src instead of camcc_camnoc_axi_clk
[jgrahsl, bod] Add slow_ahb_src clock values
[jgrahsl, bod] Add cpa_ahb clock values
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Co-developed-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Julian Grahsl <jgrahsl@snap.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
At least for titan HW, CSID don't have an associated regulator. This change
is necessary to be able to model this in the CSID resources.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs is passed to various v4l2_subdev_pad_ops.
I was working on subdev internal routing between pads, and realized that
there's no way to add TRY functionality for routes, which is not pad
specific configuration. Adding a separate struct for try-route config
wouldn't work either, as e.g. set-fmt needs to know the try-route
configuration to propagate the settings.
This patch adds a new struct, 'struct v4l2_subdev_state' (which at the
moment only contains the v4l2_subdev_pad_config array) and the new
struct is used in most of the places where v4l2_subdev_pad_config was
used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config
are changed to instead take v4l2_subdev_state.
The changes to drivers/media/v4l2-core/v4l2-subdev.c and
include/media/v4l2-subdev.h were written by hand, and all the driver
changes were done with the semantic patch below. The spatch needs to be
applied to a select list of directories. I used the following shell
commands to apply the spatch:
dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media"
for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done
Note that Coccinelle chokes on a few drivers (gcc extensions?). With
minor changes we can make Coccinelle run fine, and these changes can be
reverted after spatch. The diff for these changes is:
For drivers/media/i2c/s5k5baf.c:
@@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
&s5k5baf_cis_rect,
v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS),
v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS),
- v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT)
+ v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT),
};
s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
return 0;
For drivers/media/platform/s3c-camif/camif-capture.c:
@@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
*mf = camif->mbus_fmt;
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* crop rectangle at camera interface input */
mf->width = camif->camif_crop.width;
mf->height = camif->camif_crop.height;
@@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
}
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* Pixel format can be only changed on the sink pad. */
mf->code = camif->mbus_fmt.code;
mf->width = crop->width;
The semantic patch is:
// <smpl>
// Change function parameter
@@
identifier func;
identifier cfg;
@@
func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...)
{
<...
- cfg
+ sd_state
...>
}
// Change function declaration parameter
@@
identifier func;
identifier cfg;
type T;
@@
T func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...);
// Change function return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...)
{
...
}
// Change function declaration return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...);
// Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it
// inside a pad_state.
@@
identifier func;
identifier pad_cfg;
@@
func(...)
{
...
struct v4l2_subdev_pad_config pad_cfg;
+ struct v4l2_subdev_state pad_state = { .pads = &pad_cfg };
<+...
(
v4l2_subdev_call
|
sensor_call
|
isi_try_fse
|
isc_try_fse
|
saa_call_all
)
(...,
- &pad_cfg
+ &pad_state
,...)
...+>
}
// If the function uses fields from pad_config, access via state->pads
@@
identifier func;
identifier state;
@@
func(...,
struct v4l2_subdev_state *state
, ...)
{
<...
(
- state->try_fmt
+ state->pads->try_fmt
|
- state->try_crop
+ state->pads->try_crop
|
- state->try_compose
+ state->pads->try_compose
)
...>
}
// If the function accesses the filehandle, use fh->state instead
@@
struct v4l2_subdev_fh *fh;
@@
- fh->pad
+ fh->state
@@
struct v4l2_subdev_fh fh;
@@
- fh.pad
+ fh.state
// Start of vsp1 specific
@@
@@
struct vsp1_entity {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
};
@@
symbol entity;
@@
vsp1_entity_init(...)
{
...
entity->config =
- v4l2_subdev_alloc_pad_config
+ v4l2_subdev_alloc_state
(&entity->subdev);
...
}
@@
symbol entity;
@@
vsp1_entity_destroy(...)
{
...
- v4l2_subdev_free_pad_config
+ v4l2_subdev_free_state
(entity->config);
...
}
@exists@
identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)";
symbol config;
@@
func(...) {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
}
// End of vsp1 specific
// Start of rcar specific
@@
identifier sd;
identifier pad_cfg;
@@
rvin_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
// End of rcar specific
// Start of rockchip specific
@@
identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)";
symbol rsz;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = rsz->pad_cfg };
...
- rsz->pad_cfg
+ &state
...
}
@@
identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)";
symbol isp;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = isp->pad_cfg };
...
- isp->pad_cfg
+ &state
...
}
@@
symbol rkisp1;
symbol isp;
symbol pad_cfg;
@@
rkisp1_isp_register(...)
{
+ struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg };
...
- rkisp1->isp.pad_cfg
+ &state
...
}
// End of rockchip specific
// Start of tegra-video specific
@@
identifier sd;
identifier pad_cfg;
@@
__tegra_channel_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
@@
identifier sd_state;
@@
__tegra_channel_try_format(...)
{
...
struct v4l2_subdev_state *sd_state;
<...
- sd_state->try_crop
+ sd_state->pads->try_crop
...>
}
// End of tegra-video specific
// </smpl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable because of requesting.
this patch is made base on "add IRQF_NO_AUTOEN for request_irq" which
is being merged: https://lore.kernel.org/patchwork/patch/1388765/
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: dingsenjie <dingsenjie@yulong.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add register definitions for version 170 of the Titan architecture
and implement support for the CSID subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to support Qualcomm ISP hardware architectures that diverge
from older architectures, the CSID subdevice drivers needs to be refactored
to better abstract the different ISP hardware architectures.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CSI-2 spec defines format identifier for Data Type (DT),
and how the Decode Format (DF) & Encode Format (EF) are implemented.
The spec does however not define the DF, EF or Plain Format (PF)
identifiers, as those are vendor specific.
Plain formats describe the size of the pixels written by the RDI
units to memory. PLAIN8 for example has the size 8 bits, and
PLAIN32 32 bits. The appropriate Plain Format is determined by
the Decode Format used. The smallest Plain Format that is able
to contain a pixel of the used Decode Format is the appropriate
one to use.
As the vendor specific identifiers differ between hardware
generations, split them out into separate headers.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are places in the camss driver where camss_get_pixel_clock() is
called to get the pixel rate (using V4L2_CID_PIXEL_RATE control) and to
calculate the link frequency from it. There is a case when this would
not work: when V4L2_CID_PIXEL_RATE gets the rate at which the pixels are
read (sampled) from the sensor's pixel array, and this rate is different
from the pixel transmission rate over the CSI link, the link frequency
value can't be calculated from the pixel rate. One needs to use
V4L2_CID_LINK_FREQ to get the link frequency in this case.
Replace such calls to camss_get_pixel_clock() with calls to a wrapper
around v4l2_get_link_freq(). v4l2_get_link_freq() tries V4L2_CID_LINK_FREQ
first, and if it is not implemented by the camera sensor driver, falls
back to V4L2_CID_PIXEL_RATE to calculate the link frequency value from.
Calls to camss_get_pixel_clock() from vfe_[check,set]_clock_rates()
are left intact as it looks like this VFE clock does depend on the
rate the pixel samples comes out of the camera sensor, not on the
frequency at which the link between the sensor and the CSI receiver
operates.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the Qualcomm SDM630/636/660 and SDA variants' camera
subsystem. These SoCs are equipped with:
- 3x CSI PHY 3-Phase v1.0 (downstream csiphy-v3.5)
- 4x CSID v5.0
- 2x ISPIF v3.0
- 2x VFE 4.8
As a note, this camera subsystem is very similar to the one that
is found in the MSM8998/APQ8098 SoCs.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently for msm_csiphy, msm_csid, and msm_ispif subdevices the media
entity function field is set to MEDIA_ENT_F_IO_V4L. This is incorrect
as MEDIA_ENT_F_IO_V4L implies V4L2 video node.
Change it to MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER as this is the best
fit from the functions defined in include/uapi/linux/media.h.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Tested-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Multiple files in this driver fail to build because of missing
header inclusions:
drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c: In function 'csiphy_hw_version_read':
drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c:31:18: error: implicit declaration of function 'readl_relaxed'; did you mean 'xchg_relaxed'? [-Werror=implicit-function-declaration]
drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c: In function 'csiphy_hw_version_read':
drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c:52:2: error: implicit declaration of function 'writel' [-Werror=implicit-function-declaration]
Add linux/io.h there and in all other files that call
readl/writel and related interfaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changing a user control value can trigger an event to other
users. Add support for that.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for 10-bit packed V4L2_PIX_FMT_Y10P (on 8x16 and 8x96)
and unpacked V4L2_PIX_FMT_Y10 (on 8x96 only) pixel formats.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for RAW MIPI14 format for RDI mode on 8x96.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the PRDI mode on 8x96 to allow to configure RAW MIPI10
to Plain16 format conversion.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Usually the format on the source pad is the same as on the sink pad.
However the CSID is able to do some format conversions. To support
this make the format on the source pad selectable amongst a list
of formats. This list can be different for each sink pad format.
This is still not used but will be when the format conversions
are implemented.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the 8x16 and 8x96 support different formats, separate the
arrays which contain the supported formats. For the VFE also
add separate arrays for RDI and PIX subdevices.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CSID hardware modules on 8x16 and 8x96 are similar. There is no
need to duplicate the code by adding separate versions. Just
update the register macros to return the correct register
addresses.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a PM domain for each of the VFE hardware modules. Add
support for basic runtime PM support to be able to control the
PM domains. When a PM domain needs to be powered on - a device
link is created. When a PM domain needs to be powered off -
its device link is removed. This allows separate and
independent control of the PM domains.
Suspend/Resume is still not supported.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add structs with 8x96 resources. As the number of CSIPHY, CSID
and VFE hardware modules is different on 8x16 and 8x96 select
the number at runtime and allocate needed structures
dynamically.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSID decodes the input data stream. When the input comes from
the Test Generator the format of the stream is set on the source
media pad. When the input comes from the CSIPHY the format is the
one on the sink media pad. Use the proper format for each case.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use SPDX license headers for all files of the Qualcomm CAMSS driver.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support for camera subsystem on QComm MSM8996/APQ8096 is to be added
so remove hardware version from CAMSS driver's path.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
