When using VB2_DMABUF, the relationship between dma-buf and v4l2 buffer
may not one-to-one, a single dma-buf may be queued via different
v4l2 buffers, and different dma-bufs may be queued via the same
v4l2 buffer, so it's not appropriate to use the v4l2 buffer index
as the frame store id.
We can generate a frame store id according to the dma address.
Then for a given dma-buf, the id is fixed.
Driver now manages the frame store and vb2-buffer states independently.
When a dmabuf is queued via another v4l2 buffer before the buffer is
released by firmware, need to pend it until firmware release it.
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
For format H264 and HEVC, the firmware can report the parsed profile idc
and level idc to driver, these information may be useful.
Implement the H264 and HEVC profile and level control to report them.
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The functions:
vpu_color_get_default()
vpu_color_check_full_range()
vpu_color_check_primaries()
vpu_color_check_transfers()
vpu_color_check_matrix()
have been unused since 2022's
commit 1925665ef4 ("media: amphion: remove redundant check of
colorspace in venc_s_fmt")
The (empty) function vpu_mbox_enable_rx() has been unused since it
was added in 2022 by the
commit 61cbf1c1fa ("media: amphion: implement vpu core communication
based on mailbox")
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
"vpu_core->msg_buffer_size" is unused out-side of vpu_core_register().
There is no need to save this value in struct vpu_core.
Remove it and use a local variable instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
By default the amphion decoder will pre-parse 3 frames before starting
to decode the first frame. Alternatively, a block of flush padding data
can be appended to the frame, which will ensure that the decoder can
start decoding immediately after parsing the flush padding data, thus
potentially reducing decoding latency.
This mode was previously only enabled, when the display delay was set to
0. Allow the user to manually toggle the use of that mode via a module
parameter called low_latency, which enables the mode without
changing the display order.
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The amphion decoder firmware supports a low latency flush mode for the
HEVC format since v1.9.0. This feature, which is enabled when the
display delay is set to 0, can help to reduce the decoding latency by
appending some padding data to every frame.
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Cc: stable@vger.kernel.org
Fixes: b50a64fc54 ("media: amphion: add amphion vpu device driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Since commit 88785982a1 ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> # for meson-ge2d
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/media to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The video drvdata should be set before the video device is registered,
otherwise video_drvdata() may return NULL in the open() file ops, and led
to oops.
Fixes: 3cd084519c ("media: amphion: add vpu v4l2 m2m support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: TaoJiang <tao.jiang_2@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The firmware will ask the driver for memory allocation, but it will not
check the completeness of the task. Therefore, the vpu will crash until
reboot. This code will guard this bug and make the driver fail gracefully
when memory allocation cannot be completed.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Zhou Peng <eagle.zhou@nxp.com>
Signed-off-by: Mihai Despotovici <mihai.despotovici@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Report the average QP value of the current encoded frame via the
V4L2_CID_MPEG_VIDEO_AVERAGE_QP control, the value applies to the last
dequeued capture buffer.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is no need to add a lock in s_ctrl callback, it has been
synchronized by the ctrl_handler's lock, otherwise it may led to
a deadlock if the driver calls v4l2_ctrl_s_ctrl().
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
'vpu_malone_frame_buffer' has been unused since the original
commit 145e936380 ("media: amphion: implement malone decoder rpc
interface").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Driver abort vpu decoding when both output and capture queues are off,
but if seek in parsing the sequence header, driver may miss aborting the
parsing. so just abort the vpu parsing directly in seek.
Meanwhile if capture is off unexpectedly, we still need to abort the
decoding and return capture buffers.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rename min_buffers_needed into min_queued_buffers and update
the documentation about it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: Drop the change where min_queued_buffers + 1 buffers would be]
[hverkuil: allocated. Now this patch only renames this field instead of making]
[hverkuil: a functional change as well.]
[hverkuil: Renamed 3 remaining min_buffers_needed occurrences.]
mutext_lock should not be called in condition of wait_event, otherwise,
when CONFIG_DEBUG_ATOMIC_SLEEP is enabled, we may meet the following
warning:
do not call blocking ops when !TASK_RUNNING; state=2
WARNING: CPU: 5 PID: 741 at kernel/sched/core.c:9859
__might_sleep+0x80/0xa4
Hardware name: Freescale i.MX8QM MEK (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc :
__might_sleep+0x80/0xa4 lr : __might_sleep+0x80/0xa4 sp : ffffffc0123738a0
x29: ffffffc0123738a0 x28: ffffffc009194c48 x27: ffffffc00bbc1050
x26: ffffff8814b282f0 x25: ffffff8814b280d0 x24: ffffff8814b28080
x23: 0000000000000001 x22: 0000000000000032 x21: ffffffc00bbc1000
x20: 000000000000011b x19: ffffffc009324670 x18: 00000000fffffffd
x17: 30303c5b20746120 x16: 74657320323d6574 x15: 617473203b474e49
x14: 00058b5b8b9aa1f1 x13: ffffffc00903cda0 x12: 00000000d744fcc9
x11: 000000000000001c x10: 00000000000009a0 x9 : ffffffc0090201f4
x8 : ffffff8828245000 x7 : 0000000000000001 x6 : 0000000000000001
x5 : 00000000410fd080 x4 : 0000000000000002 x3 : ffffff8815aab4c8
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff8828244600
Call trace:
__might_sleep+0x80/0xa4
mutex_lock+0x2c/0x80
sync_session_response+0x110/0x310
vpu_session_send_cmd+0x18c/0x244
vpu_session_start+0x38/0x70
vdec_start_session+0x1b4/0x3e0
vpu_vb2_start_streaming+0xa0/0x1c4
vb2_start_streaming+0x74/0x160
vb2_core_qbuf+0x488/0x650
vb2_qbuf+0x9c/0x100
v4l2_m2m_qbuf+0x7c/0x224
v4l2_m2m_ioctl_qbuf+0x20/0x2c
v4l_qbuf+0x50/0x6c
__video_do_ioctl+0x174/0x3f0
video_usercopy+0x210/0x7cc
video_ioctl2+0x20/0x30
v4l2_ioctl+0x48/0x6c
we need to refine check_is_responsed() to remove the mutext_lock, each
cmd has a monotonically increasing id, and cmds are executed
sequentially, so we can check the id of the last reponsed cmd, then
determine whether a command has been responded or not.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
CC: Xiaolei Wang <xiaolei.wang@windriver.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Starting with commit f6038de293 ("arm64: dts: imx8qm: Fix VPU core
alias name") the alias for VPU cores uses dashes instead of underscores.
Adjust the alias stem accordingly. Fixes the errors:
amphion-vpu-core 2d040000.vpu-core: can't get vpu core id
amphion-vpu-core 2d050000.vpu-core: can't get vpu core id
Fixes: f6038de293 ("arm64: dts: imx8qm: Fix VPU core alias name")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use vb2_get_num_buffers() to avoid using queue num_buffers field directly.
This allows us to change how the number of buffers is computed in the
future.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
CC: Ming Qian <ming.qian@nxp.com>
CC: Zhou Peng <eagle.zhou@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use vb2_get_buffer() instead of direct access to the vb2_queue bufs array.
This allows us to change the type of the bufs in the future.
After each call to vb2_get_buffer() we need to be sure that we get
a valid pointer so check the return value of all of them.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
CC: Ming Qian <ming.qian@nxp.com>
CC: Zhou Peng <eagle.zhou@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
decoder firmware may notify host some debug message,
it can help analyze the state of the firmware in case of error
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
the supported_instance_count determine the instance index range,
it shouldn't exceed the bits number of instance_mask,
otherwise the bitops of instance_mask may cross boundaries
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
assign value '-EINVAL' to ret, but the stored value is overwritten
before it can be used
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
using uninitialized value may introduce risk
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
null-checking of a pointor is suggested before dereferencing it
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
the firmware only support low latency mode for h264,
but firmware will notify an event to driver
when one frame is decoded,
if V4L2_CID_MPEG_VIDEO_DEC_DISPLAY_DELAY_ENABLE is enabled,
and V4L2_CID_MPEG_VIDEO_DEC_DISPLAY_DELAY is set to 0,
driver can display the decoded frame immediately.
Fixes: ffa331d9bf ("media: amphion: decoder implement display delay enable")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
convert numbers into meaningful names,
then it can improve the log readability
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
according to v4l2 stateful decoder document 4.5.1.3. State Machine,
the state should change from seek to initialization
if call VIDIOC_REQBUFS(OUTPUT, 0).
so reinit the vpu decoder if reqbufs output 0
Fixes: 6de8d628df ("media: amphion: add v4l2 m2m vpu decoder stateful driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The path did not match the one it was submitted into linux-firmware
which prevented generic distribution from having working CODEC.
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This simplifies the code and silences -517 error messages. Also
the reason is listed in /sys/kernel/debug/devices_deferred.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: ming_qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
-----BEGIN PGP SIGNATURE-----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=YwIy
-----END PGP SIGNATURE-----
Merge tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvement at atomisp driver, which is starting to look in
good shape
- Mediatek vcodec driver has gained support for av1 and hevc stateless
codecs
- New sensor driver: ov01a10
- verisilicon driver has gained AV1 entropy helpers
- tegra-video has gained support for Tegra20 parallel input
- dvb core has gained an extra property to better support DVB-S2X
- as usual, lots of cleanups, fixes and improvements on media drivers
* tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (253 commits)
media: wl128x: fix a clang warning
media: dvb: mb86a20s: get rid of a clang-15 warning
media: cec: i2c: ch7322: also select REGMAP
media: add HAS_IOPORT dependencies
media: tc358746: select CONFIG_GENERIC_PHY
media: mediatek: vcodec: Add dbgfs help function
media: mediatek: vcodec: Add encode to support dbgfs
media: mediatek: vcodec: Change dbgfs interface to support encode
media: mediatek: vcodec: Get each instance format type
media: mediatek: vcodec: Get each context resolution information
media: mediatek: vcodec: Add a debugfs file to get different useful information
media: mediatek: vcodec: Add debug params to control different log level
media: mediatek: vcodec: Add debugfs interface to get debug information
media: mediatek: vcodec: support stateless AV1 decoder
media: verisilicon: Conditionally ignore native formats
media: verisilicon: Enable AV1 decoder on rk3588
media: verisilicon: Add film grain feature to AV1 driver
media: verisilicon: Add Rockchip AV1 decoder
media: verisilicon: Add AV1 entropy helpers
media: verisilicon: Compute motion vectors size for AV1 frames
...
The last buffer from before the change must be marked
with the V4L2_BUF_FLAG_LAST flag,
similarly to the Drain sequence above.
initiate a drain of the capture queue in dynamic resolution change
Fixes: 6de8d628df ("media: amphion: add v4l2 m2m vpu decoder stateful driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
For format V4L2_PIX_FMT_VC1_ANNEX_G,
the separate codec data is required only once.
The repeated codec data may introduce some decoding error.
so drop the repeated codec data.
It's amphion vpu's limitation
Fixes: e670f5d672 ("media: amphion: only insert the first sequence startcode for vc1l format")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Tested-by: xiahong.bao <xiahong.bao@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
For format V4L2_PIX_FMT_VC1_ANNEX_L,
the codec data is replaced with startcode,
and then driver drop it, otherwise it may led to decoding error.
It's amphion vpu's limitation
Driver has dropped the first codec data,
but need to drop the repeated codec data too.
Fixes: e670f5d672 ("media: amphion: only insert the first sequence startcode for vc1l format")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Tested-by: xiahong.bao <xiahong.bao@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
BACKGROUND
==========
When multiple work items are queued to a workqueue, their execution order
doesn't match the queueing order. They may get executed in any order and
simultaneously. When fully serialized execution - one by one in the
queueing order - is needed, an ordered workqueue should be used which can
be created with alloc_ordered_workqueue().
However, alloc_ordered_workqueue() was a later addition. Before it, an
ordered workqueue could be obtained by creating an UNBOUND workqueue with
@max_active==1. This originally was an implementation side-effect which was
broken by 4c16bd327c ("workqueue: restore WQ_UNBOUND/max_active==1 to be
ordered"). Because there were users that depended on the ordered execution,
5c0338c687 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered")
made workqueue allocation path to implicitly promote UNBOUND workqueues w/
@max_active==1 to ordered workqueues.
While this has worked okay, overloading the UNBOUND allocation interface
this way creates other issues. It's difficult to tell whether a given
workqueue actually needs to be ordered and users that legitimately want a
min concurrency level wq unexpectedly gets an ordered one instead. With
planned UNBOUND workqueue updates to improve execution locality and more
prevalence of chiplet designs which can benefit from such improvements,
this isn't a state we wanna be in forever.
This patch series audits all callsites that create an UNBOUND workqueue w/
@max_active==1 and converts them to alloc_ordered_workqueue() as necessary.
WHAT TO LOOK FOR
================
The conversions are from
alloc_workqueue(WQ_UNBOUND | flags, 1, args..)
to
alloc_ordered_workqueue(flags, args...)
which don't cause any functional changes. If you know that fully ordered
execution is not necessary, please let me know. I'll drop the conversion
and instead add a comment noting the fact to reduce confusion while
conversion is in progress.
If you aren't fully sure, it's completely fine to let the conversion
through. The behavior will stay exactly the same and we can always
reconsider later.
As there are follow-up workqueue core changes, I'd really appreciate if the
patch can be routed through the workqueue tree w/ your acks. Thanks.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ming Qian <ming.qian@nxp.com>
Cc: Shijie Qin <shijie.qin@nxp.com>
Cc: Zhou Peng <eagle.zhou@nxp.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
amphion decoder add support for the RealVideo video.
RV30 and RV40 are support by amphion decoder.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Sorenson Spark is an implementation of H.263 for use
in Flash Video and Adobe Flash files.
amphion decoder can support it by insert some startcode
before sequence and picture.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
amphion vpu support a low latency mode,
when V4L2_CID_MPEG_VIDEO_DEC_DISPLAY_DELAY_ENABLE is enabled,
decoder can display frame immediately after it's decoded.
Only h264 is support yet.
Fixes: 6de8d628df ("media: amphion: add v4l2 m2m vpu decoder stateful driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
in the E.2.1 of Rec. ITU-T H.264 (06/2019),
0 of colour primaries is reserved, and 2 is unspecified.
driver can map V4L2_COLORSPACE_LAST to 0,
and map V4L2_COLORSPACE_DEFAULT to 2.
v4l2_xfer_func and v4l2_ycbcr_encoding are similar case.
Fixes: 3cd084519c ("media: amphion: add vpu v4l2 m2m support")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
record the colorspace set by user.
if it's not supported by h264 vui, then zero will be written to vui,
but don't modify the user setting.
Fixes: 0401e659c1 ("media: amphion: add v4l2 m2m vpu encoder stateful driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
driver needs to cancel vpu before releasing the vpu instance,
so call v4l2_m2m_ctx_release() first,
to handle the redundant event triggered after m2m_ctx is released.
lock and check m2m_ctx in the event handler.
Fixes: 3cd084519c ("media: amphion: add vpu v4l2 m2m support")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
firmware should be waked up by start or configure command,
but there is a very small chance that firmware failed to wakeup.
in such case, try to wakeup firmware again by sending a noop command
Fixes: 6de8d628df ("media: amphion: add v4l2 m2m vpu decoder stateful driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
