The Google Kinox device uses the same approach as the Google Brask
which enables the HDMI CEC via the cros-ec-cec driver.
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Google Moli device uses the same approach as the Google Brask
which enables the HDMI CEC via the cros-ec-cec driver.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If there is a hardware problem such as someone pulling the CEC line low
continuously, then the POLL message will fail with an error other than
OK, NACK, ABORTED or TIMEOUT. Log the tx_status value in that case to
help debug this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Using an activation counter to decide when the enable or disable the
cec adapter is not the best approach and can lead to race conditions.
Change this to determining the current status of the adapter, and
enable or disable the adapter accordingly.
It now only needs to be called whenever there is a chance that the
state changes, and it can handle enabling/disabling monitoring as
well if needed.
This simplifies the code and it should be a more robust approach as well.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the physical address changes (i.e. becomes invalid, then valid again)
while the adapter is still claiming free logical addresses, then trigger
a reconfiguration since any claimed LAs may now be stale.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If an adapter is trying to claim a free logical address then it is
in the 'is_configuring' state. If during that process the cable is
disconnected (HPD goes low, which in turn invalidates the physical
address), then cec_adap_unconfigure() is called, and that set the
is_configuring boolean to false, even though the thread that's
trying to claim an LA is still running.
Don't touch the is_configuring bool in cec_adap_unconfigure(), it
will eventually be cleared by the thread. By making that change
the cec_config_log_addr() function also had to change: it was
aborting if is_configuring became false (since that is what
cec_adap_unconfigure() did), but that no longer works. Instead
check if the physical address is invalid. That is a much
more appropriate check anyway.
This fixes a bug where the the adapter could be disabled even
though the device was still configuring. This could cause POLL
transmits to time out.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If, while trying to claim a free logical address, a POLL message
times out, then abort this process. A CEC_TX_STATUS_TIMEOUT
should be handled the same as a CEC_TX_STATUS_ABORTED.
This avoids a situation where transmits time out due to a
driver or hardware bug and it takes ages before the attempt
to find available free logical addresses finishes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The __cec_s_log_addrs() function can configure or unconfigure the
adapter. The ioctl handler in cec-api.c will prevent it from being
called to configure the adapter if it was already configured (or in
the process of configuring). But it can still be called to unconfigure
an already unconfigured adapter, and it didn't check for that.
This can cause cec_activate_cnt_dec() to be called too often, causing
a WARN_ON.
Instead first check if adap->log_addrs.num_log_addrs == 0 and return
since in that case the adapter is already unconfigured.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It's OK to keep the pending pin events when disabling or
enabling the 'adapter'. Zeroing this can cause a race condition
if this happens when the pin kthread is handling a pin event
and calls atomic_dec later, causing work_pin_num_events to become
negative.
Just leave pending events in the queue, they'll be read eventually.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the adap_enable callback is called the adap->lock is held.
When disabling the adapter it attempts to stop the kthread that
deals with receiving and transmitting messages. However, kthread_stop
waits for the thread to stop, so all that time adap->lock is held.
Unfortunately, the kernel thread itself can call functions that take
that same lock, so a deadlock can occur.
Change the logic to keep the kernel thread running and instead when
disabling the adapter, just set the pin to high, go to idle and then
to state OFF and disable the interrupt. Only stop the kernel thread
when the adapter is deleted.
This way disabling the adapter will not wait for anything and the
deadlock is avoided.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
smb_word_op() has a parameter data_format that
determines if the data is either a byte or
word. From inspection, smb_word_op() is only
used by the macros smb_wr16() and smb_rd16()
both pass in CMD_WORD_DATA. There is no use of
smb_word_op() that passes in CMD_BYTE_DATA.
So remove the byte handling.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This new optional callback is called when the adapter is fully configured
or fully unconfigured. Some drivers may have to take action when this
happens.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allow drivers to change the transmit timeout value, i.e. after how
long should a transmit be considered 'lost', i.e. the corresponding
cec_transmit_done_ts was never called.
Some CEC devices have their own timeout, and so this timeout value must be
longer than that hardware timeout value. If it is shorter then the
framework would consider the transmit lost, even though it is effectively
still in progress at the hardware level.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use call_(void_)op consistently in the CEC core framework. Ditto
for the cec pin ops. And check if !adap->devnode.unregistered before
calling each op. This avoids calls to ops when the device has been
unregistered and the underlying hardware may be gone.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The results of non-blocking transmits were not correctly communicated
to userspace.
Specifically:
1) if a non-blocking transmit was canceled, then rx_status wasn't set to 0
as it should.
2) if the non-blocking transmit succeeded, but the corresponding reply
never arrived (aborted or timed out), then tx_status wasn't set to 0
as it should, and rx_status was hardcoded to ABORTED instead of the
actual reason, such as TIMEOUT. In addition, adap->ops->received() was
never called, so drivers that want to do message processing themselves
would not be informed of the failed reply.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a transmit-in-progress was canceled, then, once the transmit
is done, mark it as aborted and refrain from retrying the transmit.
To signal this situation the new transmit_in_progress_aborted field is
set to true.
The old implementation would just set adap->transmitting to NULL and
set adap->transmit_in_progress to false, but on the hardware level
the transmit was still ongoing. However, the framework would think
the transmit was aborted, and if a new transmit was issued, then
it could overwrite the HW buffer containing the old transmit with the
new transmit, leading to garbled data on the CEC bus.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't enable/disable the adapter if the first fh is opened or the
last fh is closed, instead do this when the adapter is configured
or unconfigured, and also when we enter Monitor All or Monitor Pin
mode for the first time or we exit the Monitor All/Pin mode for the
last time.
However, if needs_hpd is true, then do this when the physical
address is set or cleared: in that case the adapter typically is
powered by the HPD, so it really is disabled when the HPD is low.
This case (needs_hpd is true) was already handled in this way, so
this wasn't changed.
The problem with the old behavior was that if the HPD goes low when
no fh is open, and a transmit was in progress, then the adapter would
be disabled, typically stopping the transmit immediately which
leaves a partial message on the bus, which isn't nice and can confuse
some adapters.
It makes much more sense to disable it only when the adapter is
unconfigured and we're not monitoring the bus, since then you really
won't be using it anymore.
To keep track of this store a CEC activation count and call adap_enable
only when it goes from 0 to 1 or back to 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It is hard to keep all those options aligned as newer config
changes get added, and we really don't want to have patches adding
new options also touching already existing entries.
So, drop the extra spaces.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Newlines were missing in almost all regular and debug printk.
Signed-off-by: Ettore Chimenti <ek5.chimenti@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This driver uses GPIO descriptors not the old legacy GPIO
API so stop including <linux/gpio.h>.
Fix a bug using a completely unrelated legacy API flag
GPIOF_IN by switching to the actually desired flag
GPIOD_IN.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Google Brask device uses the same approach as the Google Fizz
which enables the HDMI CEC via the cros-ec-cec driver.
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
-----BEGIN PGP SIGNATURE-----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=RKW4
-----END PGP SIGNATURE-----
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
find_first{,_zero}_bit is a more effective analogue of 'next' version if
start == 0. This patch replaces 'next' with 'first' where things look
trivial.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The cec_devnode struct has a lock meant to serialize access
to the fields of this struct. This lock is taken during
device node (un)registration and when opening or releasing a
filehandle to the device node. When the last open filehandle
is closed the cec adapter might be disabled by calling the
adap_enable driver callback with the devnode.lock held.
However, if during that callback a message or event arrives
then the driver will call one of the cec_queue_event()
variants in cec-adap.c, and those will take the same devnode.lock
to walk the open filehandle list.
This obviously causes a deadlock.
This is quite easy to reproduce with the cec-gpio driver since that
uses the cec-pin framework which generated lots of events and uses
a kernel thread for the processing, so when adap_enable is called
the thread is still running and can generate events.
But I suspect that it might also happen with other drivers if an
interrupt arrives signaling e.g. a received message before adap_enable
had a chance to disable the interrupts.
This patch adds a new mutex to serialize access to the fhs list.
When adap_enable() is called the devnode.lock mutex is held, but
not devnode.lock_fhs. The event functions in cec-adap.c will now
use devnode.lock_fhs instead of devnode.lock, ensuring that it is
safe to call those functions from the adap_enable callback.
This specific issue only happens if the last open filehandle is closed
and the physical address is invalid. This is not something that
happens during normal operation, but it does happen when monitoring
CEC traffic (e.g. cec-ctl --monitor) with an unconfigured CEC adapter.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v5.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The en/disable_irq() functions keep track of the 'depth': i.e. if
interrupts are disabled twice, then it needs to enable_irq() calls to
enable them again. The cec-pin framework didn't take this into accound
and could disable irqs multiple times, and it expected that a single
enable_irq() would enable them again.
Move all calls to en/disable_irq() to the kthread where it is easy
to keep track of the current irq state and ensure that multiple
en/disable_irq calls never happen.
If interrupts where disabled twice, then they would never turn on
again, leaving the CEC adapter in a dead state.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 865463fc03 (media: cec-pin: add error injection support)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This field is only set, but never used. Drop it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmGtOFYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1hUH/1bmlOYsscJ7biqd
VECr5HhTg6iRvwWUiOpU27fLuBeAM1ZdF0oLuCtzvbK2h8lfTclcHfueihK0GIvX
ci8BvwpOYfUdDUWHglgvGXqICqYch3PiBVMFiRRRkzcpZdyCFCirAynLdOeusdTU
72Fi2RBaIM+U/5UVKcTx0J9WJsvFcG97lnNX5nT3dUmuoSW4WmX+h4vIe8VYFVmd
8q1gD17hPL+ThTKcZApn7IsArU1LNEGRg0tYItgMJo8AMTvsZjwR6yQgXeyuQ0Xk
xp6pZwzABtnL9dfNJ95q1GhsJBX5T5XvAVjt2uR1ADbgh6TDApC1VBKICm1Nva7g
uT6S0yE=
=JNL8
-----END PGP SIGNATURE-----
Merge tag 'v5.16-rc4' into media_tree
Linux 5.16-rc4
* tag 'v5.16-rc4': (984 commits)
Linux 5.16-rc4
KVM: SVM: Do not terminate SEV-ES guests on GHCB validation failure
KVM: SEV: Fall back to vmalloc for SEV-ES scratch area if necessary
KVM: SEV: Return appropriate error codes if SEV-ES scratch setup fails
parisc: Mark cr16 CPU clocksource unstable on all SMP machines
parisc: Fix "make install" on newer debian releases
sched/uclamp: Fix rq->uclamp_max not set on first enqueue
preempt/dynamic: Fix setup_preempt_mode() return value
cifs: avoid use of dstaddr as key for fscache client cookie
cifs: add server conn_id to fscache client cookie
cifs: wait for tcon resource_id before getting fscache super
cifs: fix missed refcounting of ipc tcon
x86/xen: Add xenpv_restore_regs_and_return_to_usermode()
x86/entry: Use the correct fence macro after swapgs in kernel CR3
fget: check that the fd still exists after getting a ref to it
x86/entry: Add a fence for kernel entry SWAPGS in paranoid_entry()
x86/sev: Fix SEV-ES INS/OUTS instructions for word, dword, and qword
powercap: DTPM: Drop unused local variable from init_dtpm()
io-wq: don't retry task_work creation failure on fatal conditions
serial: 8250_bcm7271: UART errors after resuming from S2
...
smatch warns about data->list not being removed from list:
drivers/media/cec/core/cec-adap.c:926 cec_transmit_msg_fh() warn: '&data->list' not removed from list
It is a false warning, but it doesn't hurt to make the code more robust
and safely unhook data->list and data->xfer_list together with a WARN_ON
if this is actually ever needed (this really shouldn't happen).
Note that fixing the data->list warning just replaced it with a new similar
warning for data->xfer_list, so both needed to be addressed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the reply for a non-blocking transmit arrives, the sequence
field for that reply was never filled in, so userspace would have no
way of associating the reply to the original transmit.
Copy the sequence field to ensure that this is now possible.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 0dbacebede ([media] cec: move the CEC framework out of staging and to media)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Keep all of the CEC menu items grouped together.
By grouping all of these menu entries inside a menu/endmenu block,
they are forced to be kept together and they are displayed/presented
in a group for users.
Tested with xconfig, gconfig, menuconfig, and nconfig.
Fixes: 46d2a3b964 ("media: place CEC menu before MEDIA_SUPPORT")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CEC pin framework has to wait for the CEC bus to be idle for the
requested Signal Free Time before it can start a transmit.
However, the check for that was off by one, so transmits would start one
bit period (2.4ms) too late.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
tegra_cec_probe() and tegra_cec_resume() ignored possible errors of
clk_prepare_enable(). The patch fixes this.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cec pin timer overruns are measured in microseconds, but the variable
names include the millisecond symbol "ms". To avoid confusion, replace
"ms" with "us" in the variable names and printed status message.
Signed-off-by: Deborah Brouwer <deborahbrouwer3563@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
stm32_cec_probe() did not unprepare clocks on error handling paths. The
patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
While here, check if the PM runtime error was caught at
s5p_cec_adap_enable().
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's a bug at s5p_cec_adap_enable(): if called to
disable the device, it should call pm_runtime_put()
instead of pm_runtime_disable(), as the goal here is to
decrement the usage_count and not to disable PM runtime.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 1bcbf6f4b6 ("[media] cec: s5p-cec: Add s5p-cec driver")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The rx-arb-lost error injection command only works with <op> set to 'any'.
Explicitly say so in the usage message.
Also use [] to indicate that the <poll> argument is optional.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If CONFIG_I2C=m and CONFIG_CEC_CORE=y then of_find_i2c_device_by_node()
is not reachable. So use IS_REACHABLE instead of IS_ENABLED.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: a62943c145c1 ("media: cec-notifier: also search for HDMI devices on I2C")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the cec_notifier_parse_hdmi_phandle function can only be used
if the HDMI device associated with the CEC device is a platform device.
Extend the function to cover I2C devices as well, as there do exist
some I2C HDMI devices which don't handle CEC internally and need an
external CEC adapter.
[hverkuil: add missing linux/i2c.h header]
[hverkuil: only attempt to find the i2c device if CONFIG_I2C is set]
Signed-off-by: Johan Fjeldtvedt <johfjeld@cisco.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Comment has 'then' repeated twice. Let's clean it up.
Use unsigned int to maintain naming consistency.
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the CEC device was unregistered, then add EPOLLPRI to
the poll() mask. Otherwise a select() that only waits for
exceptions will not wake up. A select() that waits for
read and/or write events *will* wake up on an EPOLLERR, but
not (for some reason) if it just waits for exceptions.
Strangly the epoll functionality will wakeup on EPOLLERR if
you just wait for an exception, so in this respect select()
and epoll differ.
In the end it doesn't really matter, what matters is that
polling file handles are woken up on device unregistration.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=mi60
-----END PGP SIGNATURE-----
Merge tag 'media/v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- some rework at the uAPI pixel format docs
- the smiapp driver has started to gain support for MIPI CSS camera
sensors and was renamed
- two new sensor drivers: ov02a10 and ov9734
- Meson gained a driver for the 2D acceleration unit
- Rockchip rkisp1 driver was promoted from staging
- Cedrus driver gained support for VP8
- two new remote controller keymaps were added
- the usual set of fixes cleanups and driver improvements
* tag 'media/v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (447 commits)
media: ccs: Add support for obtaining C-PHY configuration from firmware
media: ccs-pll: Print pixel rates
media: ccs: Print written register values
media: ccs: Add support for DDR OP SYS and OP PIX clocks
media: ccs-pll: Add support for DDR OP system and pixel clocks
media: ccs: Dual PLL support
media: ccs-pll: Add trivial dual PLL support
media: ccs-pll: Separate VT divisor limit calculation from the rest
media: ccs-pll: Fix VT post-PLL divisor calculation
media: ccs-pll: Make VT divisors 16-bit
media: ccs-pll: Rework bounds checks
media: ccs-pll: Print relevant information on PLL tree
media: ccs-pll: Better separate OP and VT sub-tree calculation
media: ccs-pll: Check for derating and overrating, support non-derating sensors
media: ccs-pll: Split off VT subtree calculation
media: ccs-pll: Add C-PHY support
media: ccs-pll: Add sanity checks
media: ccs-pll: Add support flexible OP PLL pixel clock divider
media: ccs-pll: Support two cycles per pixel on OP domain
media: ccs-pll: Add support for extended input PLL clock divider
...
Starting with firmware version 10 the GET/SET_HDMI_VERSION message
was removed and GET/SET_AUTO_POWER_ON was added.
The removal of GET/SET_HDMI_VERSION caused the probe of the
Pulse-Eight to fail. Add a version check to handle this gracefully.
Also show (but do not set) the Auto Power On value.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 601282d65b ("media: pulse8-cec: use adap_free callback") used
the adap_free callback to clean up on disconnect. What I forgot was that
in the probe it will call cec_delete_adapter() followed by kfree(pulse8)
if an error occurs. But by using the adap_free callback,
cec_delete_adapter() is already freeing the pulse8 struct.
This wasn't noticed since normally the probe works fine, but Pulse-Eight
published a new firmware version that caused a probe error, so now it
hits this bug. This affects firmware version 12, but probably any
version >= 10.
Commit aa9eda7612 ("media: pulse8-cec: close serio in disconnect, not
adap_free") made this worse by adding the line 'pulse8->serio = NULL'
right after the call to cec_unregister_adapter in the disconnect()
function. Unfortunately, cec_unregister_adapter will typically call
cec_delete_adapter (unless a filehandle to the cec device is still
open), which frees the pulse8 struct. So now it will also crash on a
simple unplug of the Pulse-Eight device.
With this fix both the unplug issue and a probe() error situation are
handled correctly again.
It will still fail to probe() with a v12 firmware, that's something
to look at separately.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Fixes: aa9eda7612 ("media: pulse8-cec: close serio in disconnect, not adap_free")
Fixes: 601282d65b ("media: pulse8-cec: use adap_free callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If a CEC device node is unregistered, then it should be marked as
unregistered before waking up any filehandles that are waiting for
an event.
This ensures that there is no race condition where an application can
call CEC_DQEVENT and have the ioctl return 0 instead of ENODEV.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make the code a bit more robust by checking if the adapter has
been unregistered at the start of cec_transmit_msg_fh() and
cec_received_msg_ts(). If it is unregistered, then just return.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The kthread_config relies on the main kthread (message processing
loop) to be present, so stop kthread_config before kthread.
It's unlikely to be a problem (and I've never seen any issues), but
if nothing else it makes sense to stop the threads in this order.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For some inexplicable reason I decided to call flush_scheduled_work()
instead of cancel_delayed_work_sync(). The problem with that is that
flush_scheduled_work() waits for *all* queued scheduled work to be
completed instead of just the work itself.
This can cause a deadlock if a CEC driver also schedules work that
takes the same lock. See the comments for flush_scheduled_work() in
linux/workqueue.h.
This is exactly what has been observed a few times.
This patch simply replaces flush_scheduled_work() by
cancel_delayed_work_sync().
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v5.8 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
rc-core kapi uses nanoseconds for infrared durations for receiving, and
microseconds for sending. The uapi already uses microseconds for both,
so this patch does not change the uapi.
Infrared durations do not need nanosecond resolution. IR protocols do not
have durations shorter than about 100 microseconds. Some IR hardware offers
250 microseconds resolution, which is sufficient for most protocols.
Better hardware has 50 microsecond resolution and is enough for every
protocol I am aware off.
Unify on microseconds everywhere. This simplifies the code since less
conversion between microseconds and nanoseconds needs to be done.
This affects:
- rx_resolution member of struct rc_dev
- timeout member of struct rc_dev
- duration member in struct ir_raw_event
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Patrick Lerda <patrick9876@free.fr>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Benjamin Valentin <benpicco@googlemail.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix this smatch warning:
drivers/media/cec/core/cec-api.c:156 cec_adap_g_log_addrs() warn: check that 'log_addrs' doesn't leak information (struct has a hole after
'features')
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Do not fail probing when device_init_wakeup fails.
device_init_wakeup fails when the device is already enabled as wakeup
device. Hence, the driver fails to probe the device if:
- The device has already been enabled for wakeup (by e.g. sysfs)
- The driver has been unloaded and is being loaded again.
This goal of the patch is to fix the above cases.
Overwhelming majority of the drivers do not check device_init_wakeup
return code.
Fixes: cd70de2d35 ("media: platform: Add ChromeOS EC CEC driver")
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a CEC device driver for the Chrontel ch7322 CEC conroller.
This is an I2C device capable of sending and receiving CEC messages.
Signed-off-by: Jeff Chase <jnchase@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use of the cec notifier framework is required to support
CEC_CAP_CONNECTOR_INFO but some devices do not want physical address
updates from the notifier. This adds an option to allow registering
with a cec notifier without getting address updates.
[hans: document the new adap_controls_phys_addr bool]
Signed-off-by: Jeff Chase <jnchase@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cec_adapter struct contained a waitq field that isn't used
anywhere, so drop this.
It also contained a phys_addrs array to store any reported physical
addresses. However, this was never actually used, so this field is
removed as well. The original idea was to let the core keep track of
this information, but nothing was ever done with this. Should this
be needed in the future then it is easy enough to resurrect this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
-----BEGIN PGP SIGNATURE-----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=1NIT
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
-----BEGIN PGP SIGNATURE-----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=HeJz
-----END PGP SIGNATURE-----
Merge tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull more media updates from Mauro Carvalho Chehab:
- a set of atomisp patches. They remove several abstraction layers, and
fixes clang and gcc warnings (that were hidden via some macros that
were disabling 4 or 5 types of warnings there). There are also some
important fixes and sensor auto-detection on newer BIOSes via ACPI
_DCM tables.
- some fixes
* tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (95 commits)
media: rkvdec: Fix H264 scaling list order
media: v4l2-ctrls: Unset correct HEVC loop filter flag
media: videobuf2-dma-contig: fix bad kfree in vb2_dma_contig_clear_max_seg_size
media: v4l2-subdev.rst: correct information about v4l2 events
media: s5p-mfc: Properly handle dma_parms for the allocated devices
media: medium: cec: Make MEDIA_CEC_SUPPORT default to n if !MEDIA_SUPPORT
media: cedrus: Implement runtime PM
media: cedrus: Program output format during each run
media: atomisp: improve ACPI/DMI detection logs
media: Revert "media: atomisp: add Asus Transform T101HA ACPI vars"
media: Revert "media: atomisp: Add some ACPI detection info"
media: atomisp: improve sensor detection code to use _DSM table
media: atomisp: get rid of an iomem abstraction layer
media: atomisp: get rid of a string_support.h abstraction layer
media: atomisp: use strscpy() instead of less secure variants
media: atomisp: set DFS to MAX if sensor doesn't report fps
media: atomisp: use different dfs failed messages
media: atomisp: change the detection of ISP2401 at runtime
media: atomisp: use macros from intel-family.h
media: atomisp: don't set hpll_freq twice with different values
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Recently, MEDIA_CEC_SUPPORT became indepedent of MEDIA_SUPPORT.
However, if MEDIA_SUPPORT is not enabled, MEDIA_SUPPORT_FILTER is not
defined, and MEDIA_CEC_SUPPORT is thus enabled by default, which is not
desirable.
Fix this by adding a dependency on MEDIA_CEC_SUPPORT to the default
configuration.
Fixes: 46d2a3b964 ("media: place CEC menu before MEDIA_SUPPORT")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAl7XUmwACgkQCF8+vY7k
4RU4zg//fT32wiVAPHCCp+pDZVnWNeipXE1gnpqghd/qZXfzBPiLEC9sPS74VVkA
jf1hhR33VZpKAKTPg/b074qhRZBywEOdHZnT/0CEE1oNB61shVOnyDYzLGSq95cO
6V55ovbi5IOkrg0QEJbHpG5YHzt+pq5XeWOkqGNsHwla7N7iMGMVYfHepVVDWPnZ
0wGYFF9cAJP+X/uxqkZLDVMA/K1I+QKh6vrj/qx53/eRt8VID3+i8ig3guk4PlUq
7RLw5w/CywtNaGE5zaz7T3i2eoED71JHOTXi6RxdP1z8IDvELZ9mT95GQ+enlwqt
AS6Ju1sV40wviHMv5prJWQjJkrrtYH3S907lIjwBpQLNGbh2+5crCd/6CwumkGgv
1cCZ1dVmXpCe++9mU9AXmSkjsjGPStNcmHMOpc1Pwn9jUV3LQOOSDp8+RYdt1WHU
Iw9cyM8NOpz5Mv/B1/ZPQ1gPb9lr1gE09XyUekxtAI/nl4nNHGWO8QDuX7Odfrv9
8nfo14lk/p6XCTA8dsWJCgI5B1fgnqD4frHKWO9Uctppc/KBW41c8JpQUjBNlG/T
MhtlGwYMVgSQxpQ6wK018JUAFoWkn1Sr0zMKRayqCnMjMLHsaMwE6kq+LgmRBqbB
ersKV/9ZLYqCU1d6PhEVG6xUs6GsWdLcyhALlmHsddPSdpFXdf8=
=KNAo
-----END PGP SIGNATURE-----
Merge tag 'media/v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Media documentation is now split into admin-guide, driver-api and
userspace-api books (a longstanding request from Jon);
- The media Kconfig was reorganized, in order to make easier to select
drivers and their dependencies;
- The testing drivers now has a separate directory;
- added a new driver for Rockchip Video Decoder IP;
- The atomisp staging driver was resurrected. It is meant to work with
4 generations of cameras on Atom-based laptops, tablets and cell
phones. So, it seems worth investing time to cleanup this driver and
making it in good shape.
- Added some V4L2 core ancillary routines to help with h264 codecs;
- Added an ov2740 image sensor driver;
- The si2157 gained support for Analog TV, which, in turn, added
support for some cx231xx and cx23885 boards to also support analog
standards;
- Added some V4L2 controls (V4L2_CID_CAMERA_ORIENTATION and
V4L2_CID_CAMERA_SENSOR_ROTATION) to help identifying where the camera
is located at the device;
- VIDIOC_ENUM_FMT was extended to support MC-centric devices;
- Lots of drivers improvements and cleanups.
* tag 'media/v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (503 commits)
media: Documentation: media: Refer to mbus format documentation from CSI-2 docs
media: s5k5baf: Replace zero-length array with flexible-array
media: i2c: imx219: Drop <linux/clk-provider.h> and <linux/clkdev.h>
media: i2c: Add ov2740 image sensor driver
media: ov8856: Implement sensor module revision identification
media: ov8856: Add devicetree support
media: dt-bindings: ov8856: Document YAML bindings
media: dvb-usb: Add Cinergy S2 PCIe Dual Port support
media: dvbdev: Fix tuner->demod media controller link
media: dt-bindings: phy: phy-rockchip-dphy-rx0: move rockchip dphy rx0 bindings out of staging
media: staging: dt-bindings: phy-rockchip-dphy-rx0: remove non-used reg property
media: atomisp: unify the version for isp2401 a0 and b0 versions
media: atomisp: update TODO with the current data
media: atomisp: adjust some code at sh_css that could be broken
media: atomisp: don't produce errs for ignored IRQs
media: atomisp: print IRQ when debugging
media: atomisp: isp_mmu: don't use kmem_cache
media: atomisp: add a notice about possible leak resources
media: atomisp: disable the dynamic and reserved pools
media: atomisp: turn on camera before setting it
...
The log_addrs->log_addr_type[i] value is a u8 which is controlled by
the user and comes from the ioctl. If it's over 31 then that results in
undefined behavior (shift wrapping) and that leads to a Smatch static
checker warning. We already cap the value later so we can silence the
warning just by re-ordering the existing checks.
I think the UBSan checker will also catch this bug at runtime and
generate a warning. But otherwise the bug is harmless.
Fixes: 9881fe0ca1 ("[media] cec: add HDMI CEC framework (adapter)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
gpiod_get_value() can return negative values if an error occurs.
In several places this error code was ignored.
Ensure that errors codes are handled correctly throughout the CEC
pin framework and CEC pin drivers.
The return code of the cec_pin_ops read() callback had to be changed
from 'bool' to 'int', which mean the prototype of that callback in the
sun4i drm driver also had to be changed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Globally update my email address in six files scattered through the
tree.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
As reported by Randy:
WARNING: unmet direct dependencies detected for USB
Depends on [n]: USB_SUPPORT [=n] && USB_ARCH_HAS_HCD [=n]
Selected by [m]:
- USB_RAINSHADOW_CEC [=m] && MEDIA_CEC_SUPPORT [=y]
WARNING: unmet direct dependencies detected for USB_ACM
Depends on [n]: USB_SUPPORT [=n] && USB [=m] && TTY [=n]
Selected by [m]:
- USB_RAINSHADOW_CEC [=m] && MEDIA_CEC_SUPPORT [=y]
in order to be able to select USB_ACM, we need both USB_SUPPORT
and TTY. So, depends on those two.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While select would be a great idea for most archs, this
causes a breakage with s390:
"I don't think that's a good idea, as it suddenly enables selecting all PCI
drivers on platforms that do not have PCI.
WARNING: unmet direct dependencies detected for PCI
Depends on [n]: HAVE_PCI [=n]
Selected by [m]:
- CEC_SECO [=m] && MEDIA_CEC_SUPPORT [=y] && (X86 || IA64 || COMPILE_TEST [=y])
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Most CEC platform drivers are using VIDEO_*_CEC pattern, some with
an _HDMI extension too.
Well, they're not related to V4L2 support, and we don't really
need those big config names. So drop VIDEO_* from them, remove
_HDMI (if present) and move CEC to the start.
This way, all platform driver options are now CEC_<driver>.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As CEC support doesn't depend on MEDIA_SUPPORT, let's
place the platform drivers outside the media menu.
As a side effect, instead of depends on USB, drivers
just select it.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As CEC support doesn't depend on MEDIA_SUPPORT, let's
place the platform drivers outside the media menu.
As a side effect, instead of depends on PCI, seco driver
can select it (and DMI).
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only item that opens at the CEC Kconfig menu is related
to Remote Controller. Also, its support should not depend on
media support, so it makes sense to keep both RC and CEC together.
After this change, the main media menus that are visible
under "Device Drivers" menu are:
<*> Remote Controller support --->
[ ] HDMI CEC RC integration (NEW)
< > HDMI CEC drivers
<M> Multimedia support --->
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for moving CEC drivers to the CEC directory,
move the core to a separate place.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no need to have the CEC definitions inside the
media Kconfig, as the Kconfig parser doesn't require
symbols to be declared before their usages.
With that, the main Kconfig menu becomes cleaner.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This function is no longer used by other drivers, so it can be
made static.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This argument refers to a stable name for an HDMI port, mostly i915
(ACPI) specific. Since we'll be introducing a more generic 'name' argument
as well later, rename this now to avoid confusion.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove several functions that are no longer used now that the
conversion of cec drivers to cec_notifier_conn_(un)register() and
cec_notifier_cec_adap_(un)register() is complete.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently wait_event_interruptible_timeout is called in cec_thread_func()
when adap->transmitting is set. But if the adapter is unconfigured
while transmitting, then adap->transmitting is set to NULL. But the
hardware is still actually transmitting the message, and that's
indicated by adap->transmit_in_progress and we should wait until that
is finished or times out before transmitting new messages.
As the original commit says: adap->transmitting is the userspace view,
adap->transmit_in_progress reflects the hardware state.
However, if adap->transmitting is NULL and adap->transmit_in_progress
is true, then wait_event_interruptible is called (no timeout), which
can get stuck indefinitely if the CEC driver is flaky and never marks
the transmit-in-progress as 'done'.
So test against transmit_in_progress when deciding whether to use
the timeout variant or not, instead of testing against adap->transmitting.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 32804fcb61 ("media: cec: keep track of outstanding transmits")
Cc: <stable@vger.kernel.org> # for v4.19 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
WARN if transmit_queue_sz is 0 but do not decrement it.
The CEC adapter will become unresponsive if it goes below
0 since then it thinks there are 4 billion messages in the
queue.
Obviously this should not happen, but a driver bug could
cause this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some messages are allowed to be a broadcast message in CEC 2.0
only, and should be ignored by CEC 1.4 devices.
Unfortunately, the check was wrong, causing such messages to be
marked as invalid under CEC 2.0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Hj7G
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of stuff in here, though it hasn't been too insane this merge
apart from dealing with the security fun.
uapi:
- export different colorspace properties on DP vs HDMI
- new fourcc for ARM 16x16 block format
- syncobj: allow querying last submitted timeline value
- DRM_FORMAT_BIG_ENDIAN defined as unsigned
core:
- allow using gem vma manager in ttm
- connector/encoder/bridge doc fixes
- allow more than 3 encoders for a connector
- displayport mst suspend/resume reprobing support
- vram lazy unmapping, uniform vram mm and gem vram
- edid cleanups + AVI informframe bar info
- displayport helpers - dpcd parser added
dp_cec:
- Allow a connector to be associated with a cec device
ttm:
- pipelining with no_gpu_wait fix
- always keep BOs on the LRU
sched:
- allow free_job routine to sleep
i915:
- Block userptr from mappable GTT
- i915 perf uapi versioning
- OA stream dynamic reconfiguration
- make context persistence optional
- introduce DRM_I915_UNSTABLE Kconfig
- add fake lmem testing under unstable
- BT.2020 support for DP MSA
- struct mutex elimination
- Tigerlake display/PLL/power management improvements
- Jasper Lake PCH support
- refactor PMU for multiple GPUs
- Icelake firmware update
- Split out vga + switcheroo code
amdgpu:
- implement dma-buf import/export without helpers
- vega20 RAS enablement
- DC i2c over aux fixes
- renoir GPU reset
- DC HDCP support
- BACO support for CI/VI asics
- MSI-X support
- Arcturus EEPROM support
- Arcturus VCN encode support
- VCN dynamic powergating on RV/RV2
amdkfd:
- add navi12/14/renoir support to kfd
radeon:
- SI dpm fix ported from amdgpu
- fix bad DMA on ppc platforms
gma500:
- memory leak fixes
qxl:
- convert to new gem mmap
exynos:
- build warning fix
komeda:
- add aclk sysfs attribute
v3d:
- userspace cleanup uapi change
i810:
- fix for underflow in dispatch ioctls
ast:
- refactor show_cursor
mgag200:
- refactor show_cursor
arcgpu:
- encoder finding improvements
mediatek:
- mipi_tx, dsi and partial crtc support for MT8183 SoC
- rotation support
meson:
- add suspend/resume support
omap:
- misc refactors
tegra:
- DisplayPort support for Tegra 210, 186 and 194.
- IOMMU-backed DMA API fixes
panfrost:
- fix lockdep issue
- simplify devfreq integration
rcar-du:
- R8A774B1 SoC support
- fixes for H2 ES2.0
sun4i:
- vcc-dsi regulator support
virtio-gpu:
- vmexit vs spinlock fix
- move to gem shmem helpers
- handle large command buffers with cma"
* tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm: (1855 commits)
drm/amdgpu: invalidate mmhub semaphore workaround in gmc9/gmc10
drm/amdgpu: initialize vm_inv_eng0_sem for gfxhub and mmhub
drm/amd/amdgpu/sriov skip RLCG s/r list for arcturus VF.
drm/amd/amdgpu/sriov temporarily skip ras,dtm,hdcp for arcturus VF
drm/amdgpu/gfx10: re-init clear state buffer after gpu reset
merge fix for "ftrace: Rework event_create_dir()"
drm/amdgpu: Update Arcturus golden registers
drm/amdgpu/gfx10: fix out-of-bound mqd_backup array access
drm/amdgpu/gfx10: explicitly wait for cp idle after halt/unhalt
Revert "drm/amd/display: enable S/G for RAVEN chip"
drm/amdgpu: disable gfxoff on original raven
drm/amdgpu: remove experimental flag for Navi14
drm/amdgpu: disable gfxoff when using register read interface
drm/amdgpu/powerplay: properly set PP_GFXOFF_MASK (v2)
drm/amdgpu: fix bad DMA from INTERRUPT_CNTL2
drm/radeon: fix bad DMA from INTERRUPT_CNTL2
drm/amd/display: Fix debugfs on MST connectors
drm/amdgpu/nv: add asic func for fetching vbios from rom directly
drm/amdgpu: put flush_delayed_work at first
drm/amdgpu/vcn2.5: fix the enc loop with hw fini
...
Drivers that use the CEC pin framework have no way of processing messages
themselves by providing the 'received' callback. This is present in
cec_ops, but not in cec_pin_ops.
Add support for this callback.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is possible for one HDMI connector to have multiple CEC adapters. The
typical real-world scenario is that where one adapter is used when the
device is in standby, and one that's better/smarter when the device is
powered up.
The cec-notifier changes were made with that in mind, but I missed that in
order to support this you need to tell cec_notifier_cec_adap_unregister()
which adapter you are unregistering from the notifier.
Add this additional argument. It is currently unused, but once all drivers
use this, the CEC core will be adapted for these use-cases.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e9fc8740-6be6-43a7-beee-ce2d7b54936e@xs4all.nl
Until now the connector info API was a kernel-internal API only.
This moves it to the public API and adds the new ioctl to retrieve
this information.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of hardcoding the UI Command key values, use the new
defines.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If cec_notifier_cec_adap_unregister() is called before
cec_unregister_adapter() then everything is OK (and this is the
case today). But if it is the other way around, then
cec_notifier_unregister() is called first, and that doesn't
set n->cec_adap to NULL.
So if e.g. cec_notifier_set_phys_addr() is called after
cec_notifier_unregister() but before cec_unregister_adapter()
then n->cec_adap points to an unregistered and likely deleted
cec adapter. So just set n->cec_adap->notifier and n->cec_adap
to NULL for rubustness.
Eventually cec_notifier_unregister will disappear and this will
be simplified substantially.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check if cec_s_conn_info is called with a valid cec adapter,
do nothing if it is invalid.
This makes it possible to call this function even if CEC support is
disabled in the kernel config.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to support multiple CEC devices for an HDMI connector,
and to support cec_connector_info, drivers should use either a
cec_notifier_conn_(un)register pair of functions (HDMI drivers)
or a cec_notifier_cec_adap_(un)register pair (CEC adapter drivers).
This replaces cec_notifier_get_conn/cec_notifier_put.
For CEC adapters it is also no longer needed to call cec_notifier_register,
cec_register_cec_notifier and cec_notifier_unregister. This is now
all handled internally by the new functions.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Define struct cec_connector_info in media/cec.h and define
CEC_CAP_CONNECTOR_INFO. In a later patch this will be moved to
uapi/linux/cec.h.
The CEC_CAP_CONNECTOR_INFO capability can be set by drivers, but
cec_allocate_adapter() will remove it again until the public API
for this can be enabled once all drm drivers wire this up correctly.
Also add the cec_fill_conn_info_from_drm and cec_s_conn_info functions,
which are needed by drm drivers to fill in the cec_connector info
based on a drm_connector.
The cec_notifier_(un)register and cec_register_cec_notifier
prototypes were moved from cec-notifier.h to cec.h since cec.h no longer
includes cec-notifier.h. These headers included each other before,
which caused various problems.
Due to these changes the seco-cec driver was changed as well: it
should include cec-notifier.h, not cec.h.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
dev -> hdmi_dev
conn -> conn_name
Check if n->conn_name is not NULL before calling strcmp.
Check the result of kstrdup, and clean up on error.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit b6c96e1568 inadvertently also dropped the 'msg->len > 1' test
from the preceding sanity check. This caused compliance test failures.
Fixes: b6c96e1568 ("media: cec: allow any initiator for Ping and Image/Text View On")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzrJgUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1XAIAJajJpeKc9MVQipi
zWiI+WgHDg8gG/HnLKzP2Zp4MUjTCz30t0rnBbdo6AyK6LnPBL53yxg9q64XN7vI
p/h2ys+/DvqhIYSPWX6C++HYQT4Cb5ghxJABEIsztd3G4nfB9L2vgq9zKSNFusTD
UtfUxufciZPX515TuE4IqWMwS4Ut5daH7V3jjZunhPiayTFv64e1KbpKLLzHR0NR
DfFbrPcdp7VyCT/A5AKrqfqeB6O9dm/Fe4CsdsaKuzASCXJ6GUc/A7iZDndv/KA4
f5Xh7SGlQ2TfT1ud/aMfdw3AcMjqB8zgMJenovJ7UuHDfULBWNeAmMh/cTDwY9eY
Xgyvfm0=
=S8p9
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc2' into patchwork
Merge back from upstream into media tree, as there are some
patches merged upstream that has pontential of causing
conflicts (one actually rised a conflict already).
Linux 5.2-rc2
* tag 'v5.2-rc2': (377 commits)
Linux 5.2-rc2
random: fix soft lockup when trying to read from an uninitialized blocking pool
tracing: Silence GCC 9 array bounds warning
ext4: fix dcache lookup of !casefolded directories
locking/lock_events: Use this_cpu_add() when necessary
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
...
Some displays pull down the HPD when in standby, but CEC is still
active and the display can be woken up by sending an Image View On
or Text View On CEC command. The CEC specification doesn't tell you
what the initiator should be for such a command (without a HPD it's
unclear if the CEC adapter can claim a logical address).
This patch allows any initiator value when there is no HPD for the
Image/Text View On commands and for the Ping command.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If this flag is set, then check for root permissions and skip
all message checks expect for the core checks (i.e. validate the
length etc.).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds the userspace API to send raw unchecked CEC messages.
This will require root permissions.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This ensures all the cec_msg checks are done in the same place.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The code that fills in the CEC_MSG_CDC_MESSAGE physical address
is now done after the sanity checks. It also only does this if the
message length is >= 4 (i.e. there is room for the physical address).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cec device node can be used right after it was created, but that
leaves a race condition where the device was created, but devnode->registered
was still false. So an ioctl() would result in an error.
So set it to true before calling cdev_device_add() and to false again if
cdev_device_add returned an error.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper function to parse the DT for the hdmi-phandle property
and return the corresponding struct device pointer.
It takes care to avoid increasing the device refcount since all
we need is the device pointer. This pointer is used in the
notifier list as a key, but it is never accessed by the CEC driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Checkpatch wants to use 'help' instead of '---help---':
WARNING: prefer 'help' over '---help---' for new help texts
Let's change it globally at the media subsystem, as otherwise people
would keep using the old way.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cec chardev kobject has no name, which made it hard to
debug when kobject debugging is turned on.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The epoll function expects that whenever the poll file op is
called, the poll_wait function is also called. That didn't
always happen in cec_poll(). Fix this, otherwise epoll()
would timeout when it shouldn't.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I noticed that repeatedly running 'cec-ctl --playback' would occasionally
select 'Playback Device 2' instead of 'Playback Device 1', even though there
were no other Playback devices in the HDMI topology. This happened both with
'real' hardware and with the vivid CEC emulation, suggesting that this was an
issue in the core code that claims a logical address.
What 'cec-ctl --playback' does is to first clear all existing logical addresses,
and immediately after that configure the new desired device type.
The core code will poll the logical addresses trying to find a free address.
When found it will issue a few standard messages as per the CEC spec and return.
Those messages are queued up and will be transmitted asynchronously.
What happens is that if you run two 'cec-ctl --playback' commands in quick
succession, there is still a message of the first cec-ctl command being transmitted
when you reconfigure the adapter again in the second cec-ctl command.
When the logical addresses are cleared, then all information about outstanding
transmits inside the CEC core is also cleared, and the core is no longer aware
that there is still a transmit in flight.
When the hardware finishes the transmit it calls transmit_done and the CEC core
thinks it is actually in response of a POLL messages that is trying to find a
free logical address. The result of all this is that the core thinks that the
logical address for Playback Device 1 is in use, when it is really an earlier
transmit that ended.
The main transmit thread looks at adap->transmitting to check if a transmit
is in progress, but that is set to NULL when the adapter is unconfigured.
adap->transmitting represents the view of userspace, not that of the hardware.
So when unconfiguring the adapter the message is marked aborted from the point
of view of userspace, but seen from the PoV of the hardware it is still ongoing.
So introduce a new bool transmit_in_progress that represents the hardware state
and use that instead of adap->transmitting. Now the CEC core waits until the
hardware finishes the transmit before starting a new transmit.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If debug_phys_addr is set, then CEC_CAP_PHYS_ADDR is added to the CEC
adapter capabilities.
This allows for testing CEC even if the physical address isn't set. This
makes it possible to connect two HDMI outputs together and still use CEC.
Very useful for testing CEC if you don't have access to an HDMI receiver
under linux.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CEC specification requires that the Vendor ID (if any) is reported
after a logical address was claimed.
This was never done, so add support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the tx_ignore_nack_until_eom error injection was activated,
then tx_nacked was never set instead of setting it when the last
byte of the message was transmitted.
As a result the transmit was marked as OK, when it should have
been NACKed.
Modify the condition so that it always sets tx_nacked when the
last byte of the message was transmitted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The "transmit queue full" message doesn't warrant debug level 1 since
it is already clear from the error code what's going on.
Bump to level 2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
During the configuration phase of a CEC adapter it is trying to claim a
free logical address by polling.
However, the code doesn't check if there were errors other than OK or NACK,
those are just treated as if the poll was NACKed.
Instead check for such errors and retry the poll. And if the problem persists
then don't claim this LA since there is something weird going on.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the wait for completion was interrupted, then make sure to cancel
any delayed work.
This can only happen if a transmit is waiting for a reply, and you press
Ctrl-C or reboot/poweroff or something like that which interrupts the
thread waiting for the reply and then proceeds to delete the CEC message.
Since the delayed work wasn't canceled, once it would trigger it referred
to stale data and resulted in a kernel oops.
Fixes: 7ec2b3b941 ("cec: add new tx/rx status bits to detect aborts/timeouts")
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
An RC device is does not need to be called 'RC for'. Simply the name
will suffice.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If a receive is in progress or starts before the transmit has
a chance, then lower the Signal Free Time of the upcoming transmit
to no more than CEC_SIGNAL_FREE_TIME_NEW_INITIATOR.
This is per the specification requirements.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The calculation of the Signal Free Time in the framework was not
correct. If a message was received, then the next transmit should be
considered a New Initiator and use a shorter SFT value.
This was not done with the result that if both sides where continually
sending messages, they both could use the same SFT value and one side
could deny the other side access to the bus.
Note that this fix does not take the corner case into account where
a receive is in progress when you call adap_transmit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the HDMI cable is disconnected or the CEC adapter is manually
unconfigured, then all pending transmits and wait-for-replies are
aborted. Signal this with new status bits (CEC_RX/TX_STATUS_ABORTED).
If due to (usually) a driver bug a transmit never ends (i.e. the
transmit_done was never called by the driver), then when this times
out the message is marked with CEC_TX_STATUS_TIMEOUT.
This should not happen and is an indication of a driver bug.
Without a separate status bit for this it was impossible to detect
this from userspace.
The 'transmit timed out' kernel message is now a warning, so this
should be more prominent in the kernel log as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move cec_get_edid_phys_addr() to cec-adap.c. It's not worth keeping
a separate source for this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Several CEC functions are actually specific for use with receivers,
i.e. they should be part of the V4L2 subsystem, not CEC.
These functions deal with validating and modifying EDIDs for (HDMI)
receivers, and they do not actually have anything to do with the CEC
subsystem and whether or not CEC is enabled. The problem was that if
the CEC_CORE config option was not set, then these functions would
become stubs, but that's not right: they should always be valid.
So replace the cec_ prefix by v4l2_ and move them to v4l2-dv-timings.c.
Update all drivers that call these accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cec_phys_addr_validate() function will be moved to V4L2,
so use a simplified variant of that function in cec-api.c.
cec now no longer calls cec_phys_addr_validate() and it can
be safely moved to V4L2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This function is needed by both V4L2 and CEC, so move this to
cec.h as a static inline since there are no obvious shared
modules between the two subsystems.
This patch, together with the following ones, fixes a
dependency bug: if CEC_CORE is disabled, then building adv7604
(and other HDMI receivers) will fail because an essential
function is now stubbed out.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All the CEC ioctls are compatible, and they are only implemented
in one driver, so we can simply let this driver handle them
natively.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
Add support for the new 5V CEC events
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In non device-tree world, we can need to get the notifier by the driver
name directly and eventually defer probe if not yet created.
This patch adds a variant of the get function by using the device name
instead and will not create a notifier if not yet created.
But the i915 driver exposes at least 2 HDMI connectors, this patch also
adds the possibility to add a connector name tied to the notifier device
to form a tuple and associate different CEC controllers for each HDMI
connectors.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When a message was canceled it could return tx_status with
both OK and MAX_RETRIES set, which is illegal.
If a canceled message was waiting for a reply, then rx_status
wasn't updated, so set that as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current logic makes Smatch to false-detect a Spectre variant 1
vulnerability. The problem is that it initializes an u32 indirectly
from user space input.
After trying to write a fixup, after a while I realized that, in
practice, this shouldn't be a problem, as an u32 is initialized
from u8, but it took some time to discover it.
So, do some code cleanup to make it clearer for both humans
and machines about the valid range for "op".
Fix this warning:
drivers/media/cec/cec-pin-error-inj.c:170 cec_pin_error_inj_parse_line() warn: potential spectre issue 'pin->error_inj_args'
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Each IR protocol has its own repeat period. We can minimise the keyup
timer to be the protocol period + IR timeout. This makes keys less
"sticky" and makes IR more reactive and nicer to use.
This feature was previously attempted in commit d57ea877af ("media: rc:
per-protocol repeat period"), but that did not take the IR timeout into
account, and had to be reverted.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Setting v with the CEC_PIN_EVENT_FL_DROPPED is incorrect, instead
ev should be set with this bit. Fix this.
Detected by CoverityScan, CID#1467974 ("Extra high-order bits")
Fixes: 6ec1cbf6b1 ("media: cec: improve CEC pin event handling")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/cec/cec-pin-error-inj.c:231
cec_pin_error_inj_parse_line() error: uninitialized symbol 'pos'.
The tx-add-bytes command didn't check for the presence of an argument, and
also didn't check that it was > 0.
This should fix this error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Older Kernels use a struct for ktime_t, which requires the conversion
function ktime_to_ns to be used on some places. With this patch it will
compile now also for older Kernel versions.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the adapter doesn't have error_inj_parse_line() ops, the
write() logic won't return -EINVAL, but, instead, it will keep
looping, because "count" is a non-negative number.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It turns out that the struct cec_fh event buffer size of 64 events
(64 for CEC_EVENT_PIN_CEC_LOW and 64 for _HIGH) is too small. It's
about 160 ms worth of events and if the Raspberry Pi is busy, then it
might take too long for the application to be scheduled so that it can
drain the pending events. Increase these buffers to 800 events which
is at least 2 seconds worth of events.
There is also a FIFO in between the interrupt and the cec-pin thread.
The thread passes the events on to the CEC core. It is important that
should this FIFO fill up the cec core will be informed that events
have been lost so this can be communicated to the user by setting
CEC_EVENT_FL_DROPPED_EVENTS.
It is very hard to debug CEC problems if events were lost without
informing the user of that fact.
If events were dropped due to the FIFO filling up, then the debugfs
status file will let you know how many events were dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Keep track of the number of short or long start bits, the number
of short or long data bits and the number of initiated or detected
low drive conditions.
Show this information in the status debugfs log.
Helpful when debugging, particularly when doing error injection
as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement all the error injection commands.
The state machine gets new states for the various error situations,
helper functions are added to detect whether an error injection is
active and the actual error injections are implemented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support to the CEC Pin framework to parse error injection commands
and to show them.
The next patch will do the actual implementation of this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This function will be needed for injecting a custom pulse.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add two new ops (error_inj_show and error_inj_parse_line) to support
error injection functionality for CEC adapters. If both are present,
then the core will add a new error-inj debugfs file that can be used
to see the current error injection commands and to set error injection
commands.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cec_transmit_msg_fh() first checked the message for errors, and only
after the message was found to be valid did it log the message contents.
However, that makes it hard to associate an error in the kernel log with
the message since the message contents was never logged in that case.
So swap the order: first log the message (once some very basic checks
are done), and only after that check for errors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the old license information with the corresponding SPDX
license.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=H9AS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
CEC autorepeat is different than other protocols. Autorepeat is triggered
by the first repeated user control pressed CEC message, rather than a
fixed REP_DELAY.
This change also does away with the KEY_UP event directly after the first
KEY_DOWN event, which was used to stop autorepeat from starting.
See commit a9a249a2c9 ("media: cec: fix remote control passthrough")
for the original change.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the device is being unregistered disable the hardware, don't wait
until cec_delete_adapter is called as the hardware may have disappeared by
then. This would be the case for hotplugable devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Bård Eirik Winther <bwinther@cisco.com>
Tested-by: Bård Eirik Winther <bwinther@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some devices can monitor the CEC pin using an interrupt, but you
only want to enable the interrupt if you actually switch to pin
monitoring mode.
So add a new op that is called when pin monitoring needs to be
switched on or off.
Also fix a small bug where the initial CEC pin event was sent
again when calling S_MODE twice with the same CEC_MODE_MONITOR_PIN
mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
