across all blinking LEDs and falls back to software blink if different
frequencies are requested.
* trigger: netdev: Allow configuring LED blink interval via .blink_set
even when HW offload (.hw_control) is enabled.
* led-core: Fix a race condition where a quick LED_OFF followed by another
brightness set could leave the LED off incorrectly, especially
noticeable after the introduction of the ordered workqueue.
* qcom-lpg: Add support for 6-bit PWM resolution alongside the existing
9-bit support.
* qcom-lpg: Fix PWM value capping to respect the selected resolution
(6-bit or 9-bit) for normal PWMs.
* qcom-lpg: Fix PWM value capping to respect the selected resolution for
Hi-Res PWMs.
* qcom-lpg: Fix calculation of the best period for Hi-Res PWMs to prevent
requested duty cycles from exceeding the maximum allowed by the
selected resolution.
* st1202: Add a check for the error code returned by devm_mutex_init().
* pwm-multicolor: Add a check for the return value of
fwnode_property_read_u32().
* st1202: Ensure hardware initialization (st1202_setup) happens before DT
node processing (st1202_dt_init).
* Kconfig: leds-st1202: Add select LEDS_TRIGGER_PATTERN as it's required
by the driver.
* lp8860: Drop unneeded explicit assignment to REGCACHE_NONE.
* pca955x: Refactor code with helper functions and rename some
functions/variables for clarity.
* pca955x: Pass driver data pointers instead of the I2C client to helper
functions.
* pca955x: Optimize probe LED selection logic to reduce I2C operations.
* pca955x: Revert the removal of pca95xx_num_led_regs() (renaming it to
pca955x_num_led_regs) as it's needed for HW blink support.
* st1202: Refactor st1202_led_set() to use the !! operator for boolean
conversion.
* st1202: Minor spacing and proofreading edits in comments.
* Directory Rename: Rename the drivers/leds/simple directory to
drivers/leds/simatic as the drivers within are not simple.
* mlxcpld: Remove unused include of acpi.h.
* nic78bx: Tidy up the ACPI ID table (remove ACPI_PTR, use
mod_devicetable.h, remove explicit driver_data initializer).
* tlc591xx: Convert text binding to YAML format, add child node
constraints, and fix typos/formatting in the example.
* qcom-lpg: Document the qcom,pm8937-pwm compatible string as a
fallback for qcom,pm8916-pwm.
-----BEGIN PGP SIGNATURE-----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=cEhV
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
- pca955x: Add HW blink support, utilizing PWM0. It supports one
frequency across all blinking LEDs and falls back to software blink
if different frequencies are requested.
- trigger: netdev: Allow configuring LED blink interval via .blink_set
even when HW offload (.hw_control) is enabled.
- led-core: Fix a race condition where a quick LED_OFF followed by
another brightness set could leave the LED off incorrectly,
especially noticeable after the introduction of the ordered
workqueue.
- qcom-lpg: Add support for 6-bit PWM resolution alongside the existing
9-bit support.
- qcom-lpg: Fix PWM value capping to respect the selected resolution
(6-bit or 9-bit) for normal PWMs.
- qcom-lpg: Fix PWM value capping to respect the selected resolution
for Hi-Res PWMs.
- qcom-lpg: Fix calculation of the best period for Hi-Res PWMs to
prevent requested duty cycles from exceeding the maximum allowed by
the selected resolution.
- st1202: Add a check for the error code returned by devm_mutex_init().
- pwm-multicolor: Add a check for the return value of
fwnode_property_read_u32().
- st1202: Ensure hardware initialization (st1202_setup) happens before
DT node processing (st1202_dt_init).
- Kconfig: leds-st1202: Add select LEDS_TRIGGER_PATTERN as it's
required by the driver.
- lp8860: Drop unneeded explicit assignment to REGCACHE_NONE.
- pca955x: Refactor code with helper functions and rename some
functions/variables for clarity.
- pca955x: Pass driver data pointers instead of the I2C client to
helper functions.
- pca955x: Optimize probe LED selection logic to reduce I2C operations.
- pca955x: Revert the removal of pca95xx_num_led_regs() (renaming it to
pca955x_num_led_regs) as it's needed for HW blink support.
- st1202: Refactor st1202_led_set() to use the !! operator for boolean
conversion.
- st1202: Minor spacing and proofreading edits in comments.
- Directory Rename: Rename the drivers/leds/simple directory to
drivers/leds/simatic as the drivers within are not simple.
- mlxcpld: Remove unused include of acpi.h.
- nic78bx: Tidy up the ACPI ID table (remove ACPI_PTR, use
mod_devicetable.h, remove explicit driver_data initializer).
- tlc591xx: Convert text binding to YAML format, add child node
constraints, and fix typos/formatting in the example.
- qcom-lpg: Document the qcom,pm8937-pwm compatible string as a
fallback for qcom,pm8916-pwm.
* tag 'leds-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (23 commits)
leds: nic78bx: Tidy up ACPI ID table
leds: mlxcpld: Remove unused ACPI header inclusion
leds: rgb: leds-qcom-lpg: Fix calculation of best period Hi-Res PWMs
leds: rgb: leds-qcom-lpg: Fix pwm resolution max for Hi-Res PWMs
leds: rgb: leds-qcom-lpg: Fix pwm resolution max for normal PWMs
leds: Rename simple directory to simatic
leds: Kconfig: leds-st1202: Add select for required LEDS_TRIGGER_PATTERN
leds: leds-st1202: Spacing and proofreading editing
leds: leds-st1202: Initialize hardware before DT node child operations
leds: pwm-multicolor: Add check for fwnode_property_read_u32
leds: rgb: leds-qcom-lpg: Add support for 6-bit PWM resolution
leds: Fix LED_OFF brightness race
Revert "leds-pca955x: Remove the unused function pca95xx_num_led_regs()"
leds: st1202: Refactor st1202_led_set() to use !! operator for boolean conversion
dt-bindings: leds: qcom-lpg: Document PM8937 PWM compatible
leds: pca955x: Add HW blink support
leds: pca955x: Optimize probe LED selection
leds: pca955x: Use pointers to driver data rather than I2C client
leds: pca955x: Refactor with helper functions and renaming
dt-bindings: leds: Convert leds-tlc591xx.txt to yaml format
...
Tidy up ACPI ID table:
- Drop ACPI_PTR() and hence replace acpi.h with mod_devicetable.h and
other necessary headers
- Remove explicit driver_data initializer
- Drop comma in the terminator entry
With that done, extend compile test coverage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250313161630.415515-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
leds-st1202 requires the LED Pattern Trigger (LEDS_TRIGGER_PATTERN), which
is not selected when LED Trigger support is (LEDS_TRIGGERS).
To reproduce this:
- make menuconfig KCONFIG_CONFIG=
- select LEDS_ST1202 dependencies OF, I2C and LEDS_CLASS.
- select LEDS_ST1202
- LEDS_TRIGGERS is selected but LEDS_TRIGGER_PATTERN isn't.
The absence of LEDS_TRIGGER_PATTERN explicitly required can lead to builds
in which LEDS_ST1202 is selected while LEDS_TRIGGER_PATTERN isn't. The direct
result of that would be that /sys/class/leds/<led>/hw_pattern wouldn't be
available and there would be no way of interacting with the driver and
hardware from user space.
Add select LEDS_TRIGGER_PATTERN to Kconfig to meet the requirement and
indirectly document it as well.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://lore.kernel.org/r/CWLP123MB5473F4DF3A668F7DD057A280C5C22@CWLP123MB5473.GBRP123.PROD.OUTLOOK.COM
Signed-off-by: Lee Jones <lee@kernel.org>
- Fix a memory leak in the cht-wcove driver by using devm_led_classdev_register().
- Fix an OF node reference leak in the netxbig driver.
- Ensure PWM is disabled properly in pwm-multicolor suspend.
- Add support for Texas Instruments LP8864, LP8864S, LP8866 LED-backlight drivers.
- Add support for STMicroelectronics's LED1202 12-channel LED driver.
- Convert LP8860 bindings to YAML format.
- Add bindings for the TI LP8864/LP8866 LED drivers.
- Add LED1202 LED controller bindings.
- Fix path to color definitions in leds-class-multicolor.yaml.
- Add pm660l compatible to qcom,spmi-flash-led bindings.
- Extend cznic,turris-omnia-leds binding with interrupts property.
- Add documentation for the STMicroelectronics LED1202 driver.
- Add entry for AAEON UP board FPGA drivers in MAINTAINERS.
- Fix a wrong format specifier in the ledtrig-activity driver.
- Fix a bug in the lp8860 driver where only half of the EEPROM was written.
-----BEGIN PGP SIGNATURE-----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=7V05
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
- Allow struct bin_attribute instances to be placed in read-only memory
for enhanced protection
- Fix a memory leak in the cht-wcove driver by using
devm_led_classdev_register()
- Fix an OF node reference leak in the netxbig driver
- Ensure PWM is disabled properly in pwm-multicolor suspend
- Add support for Texas Instruments LP8864, LP8864S, LP8866
LED-backlight drivers
- Add support for STMicroelectronics's LED1202 12-channel LED driver
- Convert LP8860 bindings to YAML format
- Add bindings for the TI LP8864/LP8866 LED drivers
- Add LED1202 LED controller bindings
- Fix path to color definitions in leds-class-multicolor.yaml
- Add pm660l compatible to qcom,spmi-flash-led bindings
- Extend cznic,turris-omnia-leds binding with interrupts property
- Add documentation for the STMicroelectronics LED1202 driver
- Add entry for AAEON UP board FPGA drivers in MAINTAINERS
- Fix a wrong format specifier in the ledtrig-activity driver
- Fix a bug in the lp8860 driver where only half of the EEPROM was
written
* tag 'leds-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (28 commits)
leds: triggers: Constify 'struct bin_attribute'
leds: cht-wcove: Use devm_led_classdev_register() to avoid memory leak
leds: lp8864: Add support for Texas Instruments LP8864, LP8864S, LP8866 LED-backlights
dt-bindings: leds: Convert LP8860 into YAML format
leds: Add LED1202 I2C driver
dt-bindings: leds: Add LED1202 LED Controller
Documentation:leds: Add leds-st1202.rst
leds: pwm-multicolor: Disable PWM when going to suspend
leds: netxbig: Fix an OF node reference leak in netxbig_leds_get_of_pdata()
turris-omnia-mcu-interface.h: Move macro definitions outside of enums
MAINTAINERS: Add entry for AAEON UP board FPGA drivers
leds: Add AAEON UP board LED driver
leds: trigger: netdev: Check offload ability on interface up
leds: turris-omnia: Use uppercase first letter in all comments
leds: turris-omnia: Use dev_err_probe() where appropriate
leds: turris-omnia: Inform about missing LED gamma correction feature in the MCU driver
platform: cznic: turris-omnia-mcu: Inform about missing LED panel brightness change interrupt feature
leds: turris-omnia: Notify sysfs on MCU global LEDs brightness change
leds: turris-omnia: Document driver private structures
dt-bindings: leds: cznic,turris-omnia-leds: Allow interrupts property
...
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@remote-tech.co.uk>
Link: https://lore.kernel.org/r/20241218183401.41687-4-vicentiu.galanopulo@remote-tech.co.uk
Signed-off-by: Lee Jones <lee@kernel.org>
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@remote-tech.co.uk>
Link: https://lore.kernel.org/r/20241218182001.41476-4-vicentiu.galanopulo@remote-tech.co.uk
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for LEDs on AAEON UP boards. These leds are managed by the
onboard FPGA:
- UP boards: yellow, green, red
- UP Squared boards: blue, yellow, green, red
Based on the work done by Gary Wang <garywang@aaeon.com.tw>, largely
rewritten.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20241211-aaeon-up-board-pinctrl-support-v1-2-24719be27631@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
This adds a driver that connects to the qnap-mcu mfd driver and provides
access to the LEDs on it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241107114712.538976-6-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>
Recall that on Turris Omnia, the LED controller has a global brightness
property, which allows the user to make the front LED panel dimmer.
There is also a button on the front panel, which by default is
configured so that pressing it changes the global brightness to a lower
value (unless it is at 0%, in which case pressing the button changes the
global brightness to 100%).
Newer versions of the MCU firmware support informing the SOC that the
brightness was changed by button press event via an interrupt.
Now that we have the turris-omnia-mcu driver, which adds support for MCU
interrupts, add the ability to inform the userspace (via a sysfs
notification) that the global brightness was changed.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20241111100355.6978-8-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Use the MCU command execution functions from the MCU driver instead of
the ad-hoc implementation in the LED driver. This allows as to drop the
LED driver implementation, which is a duplicate.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20241111100355.6978-3-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
With CONFIG_LEDS_CLASS_MULTICOLOR=m, a builtin leds-blinkm driver causes
a link failure:
arm-linux-gnueabi-ld: drivers/leds/leds-blinkm.o: in function `blinkm_set_mc_brightness':
leds-blinkm.c:(.text.blinkm_set_mc_brightness+0xc): undefined reference to `led_mc_calc_color_components'
Add a more specific dependency that only allows multicoler mode to
be enabled for blinkm if it can build and link.
Fixes: 56e8c56c9a ("leds: Add multicolor support to BlinkM LED driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joseph Strauss <jstrauss@mailbox.org>
Link: https://lore.kernel.org/r/20240807075614.2118068-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Add multicolor support to the BlinkM driver, making it easier to control
from userspace. The BlinkM LED is a programmable RGB LED. The driver
currently supports only the regular LED sysfs class, resulting in the
creation of three distinct classes, one for red, green, and blue. The
user then has to input three values into the three seperate brightness
files within those classes. The multicolor LED framework makes the
device easier to control with the multi_intensity file: the user can
input three values at once to form a color, while still controlling the
lightness with the brightness file.
The main struct blinkm_led has changed slightly. The struct led_classdev
for the regular sysfs classes remain. The blinkm_probe function checks
CONFIG_LEDS_BLINKM_MULTICOLOR to decide whether to load the seperate
sysfs classes or the single multicolor one, but never both. The
blinkm_set_mc_brightness() function had to be added to calculate the
three color components and then set the fields of the blinkm_data
structure accordingly.
Signed-off-by: Joseph Strauss <jstrauss@mailbox.org>
Link: https://lore.kernel.org/r/20240710184844.108006-1-jstrauss@mailbox.org
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for Texas Instruments LP5569 LED driver.
Texas Instruments LP5569 is 9 channels chip with programmable engines.
It almost a copy of LP5523 with fundamental changes to regs order and
regs content.
Has difference in how the clock is handled and doesn't support detecting
clock time automatically, different handling for selftest and different
scheme for the status regs.
LED chip supports ENGINE and MUX to group LED and run precompiled code
with magic values to run patterns. This is loaded via the sysfs entry
and it's passed as a string of ASCII HEX char.
One some devices using this LED Controller (a NBG7815 Router) it was
found loading big precompiled pattern with up to 96 bytes of code. To
have support for this "extended" scenario, hardcode each engine to
support 4 pages of precompiled pattern (128 bytes of code) and 1 page
for each MUX. This gives plenty of space for any kind precompiled
pattern keeping simple logic for page handling of each engine and mux.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20240626160027.19703-21-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ChromeOS Embedded Controller exposes an LED control command.
Expose its functionality through the leds subsystem.
The LEDs are exposed as multicolor devices.
A hardware trigger, which is active by default, is provided to let the
EC itself take over control over the LED.
The driver is designed to be probed via the cros_ec mfd device.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240613-cros_ec-led-v3-4-500b50f41e0f@weissschuh.net
Signed-off-by: Lee Jones <lee@kernel.org>
The ExpressWire library does not depend on NEW_LEDS and selecting it
from a subsystem other than LEDs may cause Kconfig warnings:
WARNING: unmet direct dependencies detected for LEDS_EXPRESSWIRE
Depends on [n]: NEW_LEDS [=n] && GPIOLIB [=y]
Selected by [y]:
- BACKLIGHT_KTD2801 [=y] && HAS_IOMEM [=y] && BACKLIGHT_CLASS_DEVICE [=y]
Move it out of the "if NEW_LEDS" block to allow selection from other
subsystems (in particular backlight) without raising this warning.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Closes: https://lore.kernel.org/20240212111819.936815-1-arnd@kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402161410.IG9I4odj-lkp@intel.com/
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Fixes: 25ae5f5f4168 ("leds: Introduce ExpressWire library")
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240216-expresswire-deps-v2-2-8be59c4a75f5@skole.hr
Signed-off-by: Lee Jones <lee@kernel.org>
Along the same lines as making devm_led_classdev_register() declared
extern unconditional, do the same thing for the two sub-classes
that have similar stubs.
The users of these interfaces go to great lengths to allow building
with both the generic leds API and the extended version, but realistically
there is not much use in this, so just simplify it to always rely
on it and remove the confusing fallback logic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240109090715.982332-2-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The ExpressWire protocol is shared between at least KTD2692 and KTD2801
with slight differences such as timings and the former not having a
defined set of pulses for enabling the protocol (possibly because it
does not support PWM unlike KTD2801). Despite these differences the
ExpressWire handling code can be shared between the two, so in
preparation for adding KTD2801 support introduce a library implementing
this protocol.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240125-ktd2801-v5-1-e22da232a825@skole.hr
Signed-off-by: Lee Jones <lee@kernel.org>
Convert the driver to be agnostic to the property provider.
LEDS subsytem is not dependent on OF, so no need to make drivers
be a such.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20231214192131.1309912-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for the Awinic aw20108 device, which belongs to the same LED
drivers family. The new device supports 108 LEDs using a matrix of 12x9
outputs."
Signed-off-by: George Stark <gnstark@salutedevices.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Link: https://lore.kernel.org/r/20231125200519.1750-10-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
The AW2013 driver uses devm_regmap_init_i2c, so REGMAP_I2C needs to
be selected.
Otherwise build process may fail with:
ld: drivers/leds/leds-aw2013.o: in function `aw2013_probe':
leds-aw2013.c:345: undefined reference to `__devm_regmap_init_i2c'
Signed-off-by: Dang Huynh <danct12@riseup.net>
Acked-by: Nikita Travkin <nikita@trvn.ru>
Fixes: 59ea3c9faf ("leds: add aw2013 driver")
Link: https://lore.kernel.org/r/20231103114203.1108922-1-danct12@riseup.net
Signed-off-by: Lee Jones <lee@kernel.org>
Some Allwinner sunxi SoCs, starting with the A100, contain an LED
controller designed to drive RGB LED pixels. Add a driver for it using
the multicolor LED framework, and with LEDs defined in the device tree.
Acked-by: Guo Ren <guoren@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20231029212738.7871-3-samuel@sholland.org
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for enabling MCU controlled mode of the Turris Omnia LEDs
via a LED private trigger called "omnia-mcu". Recall that private LED
triggers will only be listed in the sysfs trigger file for LEDs that
support them (currently there is no user of this mechanism).
When in MCU controlled mode, the user can still set LED color, but the
blinking is done by MCU, which does different things for different LEDs:
- WAN LED is blinked according to the LED[0] pin of the WAN PHY
- LAN LEDs are blinked according to the LED[0] output of the
corresponding port of the LAN switch
- PCIe LEDs are blinked according to the logical OR of the MiniPCIe port
LED pins
In the future I want to make the netdev trigger to transparently offload
the blinking to the HW if user sets compatible settings for the netdev
trigger (for LEDs associated with network devices).
There was some work on this already, and hopefully we will be able to
complete it sometime, but for now there are still multiple blockers for
this, and even if there weren't, we still would not be able to configure
HW controlled mode for the LEDs associated with MiniPCIe ports.
In the meantime let's support HW controlled mode via the private LED
trigger mechanism. If, in the future, we manage to complete the netdev
trigger offloading, we can still keep this private trigger for backwards
compatibility, if needed.
We also set "omnia-mcu" to cdev->default_trigger, so that the MCU keeps
control until the user first wants to take over it. If a different
default trigger is specified in device-tree via the
'linux,default-trigger' property, LED class will overwrite
cdev->default_trigger, and so the DT property will be respected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918161104.20860-4-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The PCA995x chips are I2C controlled LED drivers. Each chip has
up to 16 outputs, each one with an individual 8-bit resolution
PWM for brightness control.
Signed-off-by: Isai Gaspar <isaiezequiel.gaspar@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Basically rewrite the driver
Link: https://lore.kernel.org/r/20230713163516.21644-2-marex@denx.de
Signed-off-by: Lee Jones <lee@kernel.org>
This commit adds support for AWINIC AW20036/AW20054/AW20072 LED driver.
This driver supports following AW200XX features:
- Individual 64-level DIM currents
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230519130403.212479-3-mmkurbanov@sberdevices.ru
Signed-off-by: Lee Jones <lee@kernel.org>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20230522105049.1467313-18-schnelle@linux.ibm.com
Signed-off-by: Lee Jones <lee@kernel.org>
Currently, LEDS_LM3697 and LEDS_LM36274 depend on LEDS_TI_LMU_COMMON,
which contains the common code to support TI LMU devices. This means
the user is asked about the common code first, followed by the
individual drivers, if their dependencies are met.
Simplify this, and reduce the number of questions by making
LEDS_TI_LMU_COMMON invisible, and letting it be selected when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/91f6efaa48c36320e58b6a312025ae9b39ee206b.1683644796.git.geert+renesas@glider.be
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for LEDs connected to the Intel Cherry Trail Whiskey Cove
PMIC. Charger and general-purpose LEDs are supported. Hardware blinking
is implemented, breathing is not.
This driver was tested with Lenovo Yoga Book notebook.
Changes by Hans de Goede (in response to review of v2):
- Since the PMIC is connected to the battery any changes we make to
the LED settings are permanent, even surviving reboot / poweroff.
Save LED1 register settings on probe() and if auto-/hw-control was
enabled on probe() restore the settings on remove() and shutdown().
- Delay switching LED1 to software control mode to first brightness write.
- Use dynamically allocated drvdata instead of a global drvdata variable.
- Ensure the LED is on when activating blinking.
- Fix CHT_WC_LED_EFF_BREATHING val ((3 << 1) rather then BIT(3)).
Link: https://lore.kernel.org/r/20190212205901.13037-2-jekhor@gmail.com
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
The device provides 6 channels which can be individually
turned off and on but groups of two channels share a common brightness
register.
Limitation: The GPIO to enable the device is not used yet.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419111806.1100437-3-andreas@kemnade.info
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 3fce8e1eb9 ("leds: TI LMU: Add common code for TI LMU devices")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230226053953.4681-5-rdunlap@infradead.org
- HTC ASIC3 LED
- New Functionality
- Provide generic led_get() which can be used by both DT and !DT platforms
- Fix-ups
- Convert a bunch of I2C subsystem users to the new probing API
- Explicitly provide missing include files
- Make use of led_init_default_state_get() and rid the custom variants
- Use simplified fwnode_device_is_compatible() API
- Provide some Device Tree additions / adaptions
- Fix some trivial spelling issues
- Bug Fixes
- Prevent device refcount leak during led_put() and of_led_get()
- Clear previous data from temporary led_pwm structure before processing next child
- Fix Clang's warning about incompatible function types when using devm_add_action*()
-----BEGIN PGP SIGNATURE-----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=bbUo
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Removed Drivers:
- HTC ASIC3 LED
New Functionality:
- Provide generic led_get() which can be used by both DT and !DT
platforms
Fix-ups:
- Convert a bunch of I2C subsystem users to the new probing API
- Explicitly provide missing include files
- Make use of led_init_default_state_get() and rid the custom
variants
- Use simplified fwnode_device_is_compatible() API
- Provide some Device Tree additions / adaptions
- Fix some trivial spelling issues
Bug Fixes:
- Prevent device refcount leak during led_put() and of_led_get()
- Clear previous data from temporary led_pwm structure before
processing next child
- Fix Clang's warning about incompatible function types when using
devm_add_action*()"
* tag 'leds-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (41 commits)
leds: Remove ide-disk trigger
dt-bindings: leds: Add disk write/read and usb-host/usb-gadget
Documentation: leds: Correct spelling
dt-bindings: leds: Document Bluetooth and WLAN triggers
leds: Remove asic3 driver
leds: simatic-ipc-leds-gpio: Make sure we have the GPIO providing driver
leds: tca6507: Convert to use fwnode_device_is_compatible()
leds: syscon: Get rid of custom led_init_default_state_get()
leds: pm8058: Get rid of custom led_init_default_state_get()
leds: pca955x: Get rid of custom led_init_default_state_get()
leds: mt6360: Get rid of custom led_init_default_state_get()
leds: mt6323: Get rid of custom led_init_default_state_get()
leds: bcm6358: Get rid of custom led_init_default_state_get()
leds: bcm6328: Get rid of custom led_init_default_state_get()
leds: an30259a: Get rid of custom led_init_default_state_get()
leds: Move led_init_default_state_get() to the global header
leds: Add missing includes and forward declarations in leds.h
leds: is31fl319x: Wrap mutex_destroy() for devm_add_action_or_rest()
leds: turris-omnia: Convert to i2c's .probe_new()
leds: tlc591xx: Convert to i2c's .probe_new()
...
The s3c24xx platform is gone, so the led driver can be
removed as well.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Use the possessive "its" instead of the contraction "it's"
where appropriate.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The drivers/leds/rgb subdirectory is relatively fresh, so we move this
new PWM multi-color driver into it.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
By allowing to group multiple monochrome PWM LEDs into multicolor LEDs,
all involved LEDs can be controlled in-sync. This enables using effects
using triggers, etc.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The Light Pulse Generator (LPG) is a PWM-block found in a wide range of
PMICs from Qualcomm. These PMICs typically comes with 1-8 LPG instances,
with their output being routed to various other components, such as
current sinks or GPIOs.
Each LPG instance can operate on fixed parameters or based on a shared
lookup-table, altering the duty cycle over time. This provides the means
for hardware assisted transitions of LED brightness.
A typical use case for the fixed parameter mode is to drive a PWM
backlight control signal, the driver therefor allows each LPG instance
to be exposed to the kernel either through the LED framework or the PWM
framework.
A typical use case for the LED configuration is to drive RGB LEDs in
smartphones etc, for which the driver supports multiple channels to be
ganged up to a MULTICOLOR LED. In this configuration the pattern
generators will be synchronized, to allow for multi-color patterns.
The idea of modelling this as a LED driver ontop of a PWM driver was
considered, but setting the properties related to patterns does not fit
in the PWM API. Similarly the idea of just duplicating the lower bits in
a PWM and LED driver separately was considered, but this would not allow
the PWM channels and LEDs to be configured on a per-board basis. The
driver implements the more complex LED interface, and provides a PWM
interface on the side of that, in the same driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
[On the Sony Xperia Nile Discovery, SDM630]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
I had to rebase at last moment to fix wrong author of one
commit. Sorry about that.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCYd8hdwAKCRAw5/Bqldv6
8m3sAKC20ddEFW04Mk45Tw72qSyud6vhwQCaAnQy6dcd+zV6LOxosgLZdtXkvx0=
=CU+X
-----END PGP SIGNATURE-----
Merge tag 'leds-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Nothing major is happening here"
* tag 'leds-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: lp55xx: initialise output direction from dts
ARM: dts: omap3-n900: Fix lp5523 for multi color
leds: ktd2692: Drop calling dev_of_node() in ktd2692_parse_dt
leds: lgm-sso: Get rid of duplicate of_node assignment
leds: tca6507: Get rid of duplicate of_node assignment
leds: leds-fsg: Drop FSG3 LED driver
leds: lp50xx: remove unused variable
dt-bindings: leds: Replace moonlight with indicator in mt6360 example
leds: led-core: Update fwnode with device_set_node
leds: tca6507: use swap() to make code cleaner
leds: Add mt6360 driver
dt-bindings: leds: Add bindings for MT6360 LED
The board file using this driver has been deleted and the
FSG3 LEDs can be modeled using a system controller and some
register bit LEDs in the device tree so this driver is no
longer needed.
Reported-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Krzysztof Hałasa <khalasa@piap.pl>
Cc: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This driver adds initial support for several devices from Siemens. It is
based on a platform driver introduced in an earlier commit.
One of the supported machines has GPIO connected LEDs, here we poke GPIO
memory directly because pinctrl does not come up.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20211213120502.20661-3-henning.schild@siemens.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The 9-channel one is called LP5009, not LP509.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Ingi Kim <ingi2.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
