imx_gpcv2_instance will not be updated after init, so mark it with
__ro_after_init.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211214084711.1357325-1-peng.fan@oss.nxp.com
IRQ 0..7 are not supported by the driver for SPEAr320 SOC family.
IRQ 0 is not reserved in SPEAr320 SOC (assigned to GPIOINT).
Furthermore, in SPEAr320s SOC variant, IRQ 0..6 are assigned
as follow:
IRQ 6 - NGPIO_INTR: Combined status of edge programmable
interrupts from GPIO ports
IRQ 5 - TX_OR_INTR: I2S interrupt on Transmit FIFO overrun
IRQ 4 - TX_EMP_INTR: I2S interrupt on Transmit FIFO empty
IRQ 3 - RX_OR_INTR: I2S interrupt on Receive FIFO overrun
IRQ 2 - RX_DA_INTR: I2S interrupt on data available in Receive FIFO
IRQ 1 - Reserved
IRQ 0 - GPIO_INTR: Legacy interrupt from GPIO ports
Add support for these IRQs in SPEAr320 SOC family.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211202095255.165797-6-herve.codina@bootlin.com
The new memreserve cpuhp callback only needs to survive up until a point
where every CPU in the system has booted once. Beyond that, it becomes a
no-op and can be put in the bin.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211027151506.2085066-4-valentin.schneider@arm.com
Memory used by the LPI tables have to be made persistent for kexec to have
a chance to work, as explained in [1]. If they have been made persistent
and we are booting into a kexec'd kernel, we also need to free the pages
that were preemptively allocated by the new kernel for those tables.
Both of those operations currently happen during its_cpu_init(), which
happens in a _STARTING (IOW atomic) cpuhp callback for secondary
CPUs. efi_mem_reserve_iomem() issues a GFP_ATOMIC allocation, which
unfortunately doesn't work under PREEMPT_RT (this ends up grabbing a
non-raw spinlock, which can sleep under PREEMPT_RT). Similarly, freeing the
pages ends up grabbing a sleepable spinlock.
Since the memreserve is only required by kexec, it doesn't have to be done
so early in the secondary boot process. Issue the reservation in a new
CPUHP_AP_ONLINE_DYN cpuhp callback, and piggy-back the page freeing on top
of it. A CPU gets to run the body of this new callback exactly once.
As kexec issues a machine_shutdown() prior to machine_kexec(), it will be
serialized vs a CPU being plugged to life by the hotplug machinery - either
the CPU will have been brought up and have had its redistributor's pending
table memreserved, or it never went online and will have its table
allocated by the new kernel.
[1]: https://lore.kernel.org/lkml/20180921195954.21574-1-marc.zyngier@arm.com/
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211027151506.2085066-3-valentin.schneider@arm.com
Later patches will require tracking some per-rdist status. Reuse the bytes
"lost" to padding within the __percpu rdist struct as a flags field, and
re-encode ->lpi_enabled within said flags.
No change in functionality intended.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211027151506.2085066-2-valentin.schneider@arm.com
This was found by coccicheck:
./drivers/irqchip/irq-bcm7120-l2.c,328,1-7,ERROR missing put_device;
call of_find_device_by_node on line 234, but without a corresponding
object release within this function.
./drivers/irqchip/irq-bcm7120-l2.c,341,1-7,ERROR missing put_device;
call of_find_device_by_node on line 234, but without a corresponding
object release within this function.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211109055958.130287-1-ye.guojin@zte.com.cn
There is no point to have this function public as it is set by the PCI core
anyway when a PCI/MSI irqdomain is created.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI
Link: https://lore.kernel.org/r/20211206210224.157070464@linutronix.de
INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.
Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.
Signed-off-by: Wudi Wang <wangwudi@hisilicon.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com
This function is only called from the driver init code.
Signed-off-by: Donghyeok Kim <dthex5d@gmail.com>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211204164228.5920-1-dthex5d@gmail.com
Rather then restructuring the ARMv7M entrly logic per TODO, just move
NVIC to GENERIC_IRQ_MULTI_HANDLER.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
According to ARM(v7M) ARM Interrupt Priority Offsets located at
0xE000E400-0xE000E5EC, while 0xE000E300-0xE000E33C covers read-only
Interrupt Active Bit Registers
Fixes: 292ec08049 ("irqchip: Add support for ARMv7-M NVIC")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211201110259.84857-1-vladimir.murzin@arm.com
The interrupt status bits are cleared by writing 1, we should force a
write to clear the interrupt without checking if the value has changed.
Fixes: 04f605906f ("irqchip: Add Aspeed SCU interrupt controller")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211124094348.11621-1-billy_tsai@aspeedtech.com
Cc: stable@vger.kernel.org
irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: a71b9412c9 ("irqchip/armada-370-xp: Allow allocation of multiple MSIs")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125130057.26705-2-pali@kernel.org
When using "devm_request_threaded_irq(,,,,IRQF_ONESHOT,,)" in a driver,
only the first interrupt is handled, and following interrupts are never
delivered (initially reported in [1]).
That's because the RISC-V PLIC cannot EOI masked interrupts, as explained
in the description of Interrupt Completion in the PLIC spec [2]:
<quote>
The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the claim/complete
register. The PLIC does not check whether the completion ID is the same
as the last claim ID for that target. If the completion ID does not match
an interrupt source that *is currently enabled* for the target, the
completion is silently ignored.
</quote>
Re-enable the interrupt before completion if it has been masked during
the handling, and remask it afterwards.
[1] http://lists.infradead.org/pipermail/linux-riscv/2021-July/007441.html
[2] 8bc15a35d0/riscv-plic.adoc
Fixes: bb0fed1c60 ("irqchip/sifive-plic: Switch to fasteoi flow")
Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Tested-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[maz: amended commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211105094748.3894453-1-guoren@kernel.org
The mask/unmask must be implemented, and enable/disable supplement
them if the HW requires something different at startup time. When
irq source is disabled by mask, mpintc could complete irq normally.
So drop enable/disable if favour of mask/unmask.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211101134534.3804542-1-guoren@kernel.org
* irq/irq_cpu_offline:
: .
: Make irq_cpu_{on,off}line() deprecated kernel API, and only
: enable it for some obscure Cavium platform after having
: moved all the other users away from it.
:
: Next step, drop the platform itself.
: .
genirq: Hide irq_cpu_{on,off}line() behind a deprecated option
irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()
MIPS: loongson64: Drop call to irq_cpu_offline()
Signed-off-by: Marc Zyngier <maz@kernel.org>
* irq/remove-handle-domain-irq-20211026:
: Large rework of the architecture entry code from Mark Rutland.
: From the cover letter:
:
: <quote>
: The handle_domain_{irq,nmi}() functions were oringally intended as a
: convenience, but recent rework to entry code across the kernel tree has
: demonstrated that they cause more pain than they're worth and prevent
: architectures from being able to write robust entry code.
:
: This series reworks the irq code to remove them, handling the necessary
: entry work consistently in entry code (be it architectural or generic).
: </quote>
MIPS: irq: Avoid an unused-variable error
irq: remove handle_domain_{irq,nmi}()
irq: remove CONFIG_HANDLE_DOMAIN_IRQ_IRQENTRY
irq: riscv: perform irqentry in entry code
irq: openrisc: perform irqentry in entry code
irq: csky: perform irqentry in entry code
irq: arm64: perform irqentry in entry code
irq: arm: perform irqentry in entry code
irq: add a (temporary) CONFIG_HANDLE_DOMAIN_IRQ_IRQENTRY
irq: nds32: avoid CONFIG_HANDLE_DOMAIN_IRQ
irq: arc: avoid CONFIG_HANDLE_DOMAIN_IRQ
irq: add generic_handle_arch_irq()
irq: unexport handle_irq_desc()
irq: simplify handle_domain_{irq,nmi}()
irq: mips: simplify do_domain_IRQ()
irq: mips: stop (ab)using handle_domain_irq()
irq: mips: simplify bcm6345_l1_irq_handle()
irq: mips: avoid nested irq_enter()
Signed-off-by: Marc Zyngier <maz@kernel.org>
The MIPS GIC driver uses irq_cpu_online() to go and program the
per-CPU interrupts. However, this method iterates over all IRQs
in the system, despite only 3 per-CPU interrupts being of interest.
Let's be terribly bold and do the iteration ourselves. To ensure
mutual exclusion, hold the gic_lock spinlock that is otherwise
taken while dealing with these interrupts.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20211021170414.3341522-3-maz@kernel.org
Now that entry code handles IRQ entry (including setting the IRQ regs)
before calling irqchip code, irqchip code can safely call
generic_handle_domain_irq(), and there's no functional reason for it to
call handle_domain_irq().
Let's cement this split of responsibility and remove handle_domain_irq()
entirely, updating irqchip drivers to call generic_handle_domain_irq().
For consistency, handle_domain_nmi() is similarly removed and replaced
with a generic_handle_domain_nmi() function which also does not perform
any entry logic.
Previously handle_domain_{irq,nmi}() had a WARN_ON() which would fire
when they were called in an inappropriate context. So that we can
identify similar issues going forward, similar WARN_ON_ONCE() logic is
added to the generic_handle_*() functions, and comments are updated for
clarity and consistency.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
In preparation for removing HANDLE_DOMAIN_IRQ_IRQENTRY, have arch/arm
perform all the irqentry accounting in its entry code.
For configurations with CONFIG_GENERIC_IRQ_MULTI_HANDLER, we can use
generic_handle_arch_irq(). Other than asm_do_IRQ(), all C calls to
handle_IRQ() are from irqchip handlers which will be called from
generic_handle_arch_irq(), so to avoid double accounting IRQ entry, the
entry logic is moved from handle_IRQ() into asm_do_IRQ().
For ARMv7M the entry assembly is tightly coupled with the NVIC irqchip, and
while the entry code should logically live under arch/arm/, moving the
entry logic there makes things more convoluted. So for now, place the
entry logic in the NVIC irqchip, but separated into a separate
function to make the split of responsibility clear.
For all other configurations without CONFIG_GENERIC_IRQ_MULTI_HANDLER,
IRQ entry is already handled in arch code, and requires no changes.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
In preparation for removing HANDLE_DOMAIN_IRQ, have arch/nds32 perform
all the necessary IRQ entry accounting in its entry code.
Currently arch/nds32 is tightly coupled with the ativic32 irqchip, and
while the entry code should logically live under arch/nds32/, moving the
entry logic there makes things more convoluted. So for now, place the
entry logic in the ativic32 irqchip, but separated into a separate
function to make the split of responsibility clear.
In future this should probably use GENERIC_IRQ_MULTI_HANDLER to cleanly
decouple this.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Chen <deanbo422@gmail.com>
As bcm6345_l1_irq_handle() only needs to know /whether/ an IRQ was
resolved, and doesn't need to know the specific IRQ, it's simpler for it
to call generic_handle_domain_irq() directly and check the return code,
so let's do that.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
As bcm6345_l1_irq_handle() is a chained irqchip handler, it will be
invoked within the context of the root irqchip handler, which must have
entered IRQ context already.
When bcm6345_l1_irq_handle() calls arch/mips's do_IRQ() , this will nest
another call to irq_enter(), and the resulting nested increment to
`rcu_data.dynticks_nmi_nesting` will cause rcu_is_cpu_rrupt_from_idle()
to fail to identify wakeups from idle, resulting in failure to preempt,
and RCU stalls.
Chained irqchip handlers must invoke IRQ handlers by way of thee core
irqchip code, i.e. generic_handle_irq() or generic_handle_domain_irq()
and should not call do_IRQ(), which is intended only for root irqchip
handlers.
Fix bcm6345_l1_irq_handle() by calling generic_handle_irq() directly.
Fixes: c7c42ec2ba ("irqchips/bmips: Add bcm6345-l1 interrupt controller")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
* irq/mchp-eic:
: .
: New irqchip driver for the Microchip EIC block
: .
irqchip/mchp-eic: Fix return value check in mchp_eic_init()
irqchip/mchp-eic: Add support for the Microchip EIC
dt-bindings: microchip,eic: Add bindings for the Microchip EIC
Signed-off-by: Marc Zyngier <maz@kernel.org>
* irq/modular-irqchips:
: .
: Update a set of irqchip drivers to be build as modules.
:
: This includes an Amlogic and multiple Broadcom drivers, triggering
: a cascade of other changes (MIPS arch code, symbols being exported,
: config changes)
: .
irqchip: Fix kernel-doc parameter typo for IRQCHIP_DECLARE
ARM: bcm: Removed forced select of interrupt controllers
arm64: broadcom: Removed forced select of interrupt controllers
irqchip/irq-bcm7120-l2: Switch to IRQCHIP_PLATFORM_DRIVER
genirq: Export irq_gc_noop()
irqchip/irq-brcmstb-l2: Switch to IRQCHIP_PLATFORM_DRIVER
genirq: Export irq_gc_{unmask_enable,mask_disable}_reg
irqchip/irq-bcm7038-l1: Switch to IRQCHIP_PLATFORM_DRIVER
irqchip/irq-bcm7038-l1: Restrict affinity setting to MIPS
irqchip/irq-bcm7038-l1: Gate use of CPU logical map to MIPS
irqchip/irq-bcm7038-l1: Use irq_get_irq_data()
irqchip/irq-bcm7038-l1: Remove .irq_cpu_offline()
MIPS: BMIPS: Remove use of irq_cpu_offline
arm64: meson: remove MESON_IRQ_GPIO selection
irqchip/meson-gpio: Make it possible to build as a module
irqchip: Provide stronger type checking for IRQCHIP_MATCH/IRQCHIP_DECLARE
Signed-off-by: Marc Zyngier <maz@kernel.org>
In case of error, the function of_iomap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211025050055.1129845-1-yangyingliang@huawei.com
Allow the user selection and building of this interrupt controller
driver as a module since it is used on ARM/ARM64 based systems as a
second level interrupt controller hanging off the ARM GIC and is
therefore loadable during boot.
To avoid using of_irq_count() which is not exported towards module,
switch the driver to use the platform_device provided by the irqchip
platform driver code and resolve the number of interrupts using
platform_irq_count().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-11-f.fainelli@gmail.com
Allow the user selection and building of this interrupt controller
driver as a module since it is used on ARM/ARM64 based systems as a
second level interrupt controller hanging off the ARM GIC and is
therefore loadable during boot.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-9-f.fainelli@gmail.com
Allow the user selection and building of this interrupt controller
driver as a module since it is used on ARM/ARM64 based systems as a
second level interrupt controller hanging off the ARM GIC and is
therefore loadable during boot.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-7-f.fainelli@gmail.com
Only MIPS based platforms using this interrupt controller as first level
interrupt controller can actually change the affinity of interrupts by
re-programming the affinity mask of the interrupt controller and use
another word group to have another CPU process the interrupt.
When this interrupt is used as a second level interrupt controller on
ARM/ARM64 there is no way to change the interrupt affinity. This fixes a
NULL pointer de-reference while trying to change the affinity since
there is only a single word group in that case, and we would have been
overruning the intc->cpus[] array.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-6-f.fainelli@gmail.com
The use of the cpu_logical_map[] array is only relevant for MIPS based
platform where this driver is used as a first level interrupt controller
and contains multiple register groups to map with an associated CPU.
On ARM/ARM64 based systems this interrupt controller is present and used
as a second level interrupt controller hanging off the ARM GIC. That
copy of the interrupt controller contains a single group, resulting in
the intc->cpus[] array to be of size 1.
Things happened to work in that case because we install that interrupt
controller as a chained handler which does not allow it to be affine to
any CPU but the boot CPU which happens to be 0, therefore we never
de-reference past intc->cpus[] but with the current code in place, we do
leave a chance of de-referencing the array past its bounds.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-5-f.fainelli@gmail.com
Using irq_desc_get_irq_data(irq_to_desc()) to retrieve the irq_data
structure from a virtual interrupt number is going to be problematic to
make irq-bcm7038-l1 a module because irq_to_desc() is not exported, and
there is no intent to export it to modules, see 64a1b95bb9 ("genirq:
Restrict export of irq_to_desc()").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-4-f.fainelli@gmail.com
With arch/mips/kernel/smp-bmips.c having been migrated away from
irq_cpu_offline() and use irq_migrate_all_off_this_cpu() instead, we no
longer need to implement an .irq_cpu_offline() callback. This is a
necessary change to facilitate the building of this driver as a module.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-3-f.fainelli@gmail.com
Add support for Microchip External Interrupt Controller. The controller
supports 2 external interrupt lines. For every external input there is
a connection to GIC. The interrupt controllers contains only 4
registers:
- EIC_GFCS (read only): which indicates that glitch filter configuration
is ready (not addressed in this implementation)
- EIC_SCFG0R, EIC_SCFG1R (read, write): allows per interrupt specific
settings: enable, polarity/edge settings, glitch filter settings
- EIC_WPMR, EIC_WPSR: enables write protection mode specific settings
(which are architecture specific) for the controller and are not
addressed in this implementation
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210927063657.2157676-3-claudiu.beznea@microchip.com
In order to reduce the kernel Image size on multi-platform distributions,
make it possible to build the Amlogic GPIO IRQ controller as a module
by switching it to a platform driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Saravana Kannan <saravanak@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210902134914.176986-2-narmstrong@baylibre.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105723.1831-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105715.1780-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105708.1729-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105701.1678-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105653.1627-1-caihuoqing@baidu.com
Geert reported that the GIC driver locks up on a Renesas system
since 005c34ae4b ("irqchip/gic: Atomically update affinity")
fixed the driver to use writeb_relaxed() instead of writel_relaxed().
As it turns out, the interconnect used on this system mandates
32bit wide accesses for all MMIO transactions, even if the GIC
architecture specifically mandates for some registers to be byte
accessible. Gahhh...
Work around the issue by crudly detecting the offending system,
and falling back to an inefficient RMW+lock implementation.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/CAMuHMdV+Ev47K5NO8XHsanSq5YRMCHn2gWAQyV-q2LpJVy9HiQ@mail.gmail.com
This code works, but it is cleaner to use semicolons at the end of
statements instead of commas.
Extracted from a big anonymous patch by Julia Lawall
<julia.lawall@inria.fr>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/b1710bb6ea5faa7a7fe74404adb0beb951e0bf8c.1631699160.git.geert+renesas@glider.be
In its_vpe_irq_domain_alloc, when its_vpe_init() returns an error,
there is an off-by-one in the number of VPEs to be freed.
Fix it by simply passing the number of VPEs allocated, which is the
index of the loop iterating over the VPEs.
Fixes: 7d75bbb4bc ("irqchip/gic-v3-its: Add VPE irq domain allocation/teardown")
Signed-off-by: Kaige Fu <kaige.fu@linux.alibaba.com>
[maz: fixed commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/d9e36dee512e63670287ed9eff884a5d8d6d27f2.1631672311.git.kaige.fu@linux.alibaba.com
Fix kernel-doc warnings in irq-mbigen.c:
irq-mbigen.c:29: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* In mbigen vector register
irq-mbigen.c:43: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* offset of clear register in mbigen node
irq-mbigen.c:50: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* offset of interrupt type register
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Jun Ma <majun258@huawei.com>
Cc: Yun Wu <wuyun.wu@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210905033644.15988-1-rdunlap@infradead.org
When converting the driver to using handle_percpu_devid_irq,
we forgot to repaint the irq_eoi() callback into irq_ack(),
as handle_percpu_devid_fasteoi_ipi() was actually using EOI
really early in the handling. Yes this was a stupid idea.
Fix this by using the HW ack method as irq_ack().
Fixes: e52e73b7e9 ("irqchip/armada-370-xp: Make IPIs use handle_percpu_devid_irq()")
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tuiexq5f.fsf@pengutronix.de
* irq/qcom-pdc-nowake-cleanup:
: Fix the QCOM PDC mishandling of the interrupt hierarchy by trimming
: it when necessary.
: Export irq_domain_disconnect_hierarchy as a consequence of it.
irqchip/qcom-pdc: Trim unused levels of the interrupt hierarchy
irqdomain: Export irq_domain_disconnect_hierarchy()
Signed-off-by: Marc Zyngier <maz@kernel.org>
The QCOM PDC driver creates a bunch of unnecessary levels in
the interrupt hierarchy when dealing with non-wakeup-capable
interrupts. By definition, these lines are terminated at the
PDC level, and everything below this is completely fake.
This also results in additional complexity as most of the
callbacks have to check for the validity of the parent level.
Needless to say, this doesn't look very good.
Solve this by disconnecting the interrupt hierarchy below
the last valid level, and considerably simplify the handling
of all the other interrupts by avoiding now unnecessary cheks.
In most cases, the standard irq_*_parent() handlers are directly
used.
This also cures an issue reporting by Maulik where gpio_to_irq()
returns an error after having observed a set of invalid levels.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1629705880-27877-3-git-send-email-mkshah@codeaurora.org
* irq/misc-5.15:
: .
: Various irqchip fixes:
:
: - Fix edge interrupt support on loongson systems
: - Advertise lack of wake-up logic on mtk-sysirq
: - Fix mask tracking on the Apple AIC
: - Correct priority reading of arm64 pseudo-NMI when SCR_EL3.FIQ==0
: .
irqchip/gic-v3: Fix priority comparison when non-secure priorities are used
irqchip/apple-aic: Fix irq_disable from within irq handlers
Signed-off-by: Marc Zyngier <maz@kernel.org>
When non-secure priorities are used, compared to the raw priority set,
the value read back from RPR is also right-shifted by one and the
highest bit set.
Add a macro to do the modifications to the raw priority when doing the
comparison against the RPR value. This corrects the pseudo-NMI behavior
when non-secure priorities in the GIC are used. Tested on 5.10 with
the "IPI as pseudo-NMI" series [1] applied on MT8195.
[1] https://lore.kernel.org/linux-arm-kernel/1604317487-14543-1-git-send-email-sumit.garg@linaro.org/
Fixes: 3367805909 ("irqchip/gic-v3: Support pseudo-NMIs when SCR_EL3.FIQ == 0")
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[maz: Added comment contributed by Alex]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210811171505.1502090-1-wenst@chromium.org
When disable_irq_nosync for an interrupt is called from within its
interrupt handler, this interrupt is only marked as disabled with the
intention to mask it when it triggers again.
The AIC hardware however automatically masks the interrupt when it is read.
aic_irq_eoi then unmasks it again if it's not disabled *and* not masked.
This results in a state mismatch between the hardware state and the
state kept in irq_data: The hardware interrupt is masked but
IRQD_IRQ_MASKED is not set. Any further calls to unmask_irq will directly
return and the interrupt can never be enabled again.
Fix this by keeping the hardware and irq_data state in sync by unmasking in
aic_irq_eoi if and only if the irq_data state also assumes the interrupt to
be unmasked.
Fixes: 76cde26394 ("irqchip/apple-aic: Add support for the Apple Interrupt Controller")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210812100942.17206-1-sven@svenpeter.dev
- Fix edge interrupt support on loongson systems
- Advertise lack of wake-up logic on mtk-sysirq
* irq/misc-5.15:
irqchip/mtk-sysirq: Skip setting irq-wake
irqchip/loongson-pch-pic: Improve edge triggered interrupt support
Signed-off-by: Marc Zyngier <maz@kernel.org>
mtk-sysirq doesn't require specific logic to work with wakeup IRQs. To
allow registered IRQs to be used as a wakeup-source, add the flag
IRQCHIP_SKIP_SET_WAKE.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210707062004.782787-1-msp@baylibre.com
- Add support for partitionned EPPIs, modeled after the existing
partitioned PPI support
* irq/gicv3-eppi-partition:
irqchip/gic-v3: Fix selection of partition domain for EPPIs
irqchip/gic-v3: Add __gic_get_ppi_index() to find the PPI number from hwirq
Signed-off-by: Marc Zyngier <maz@kernel.org>
commit 5f51f80382 ("irqchip/gic-v3: Add EPPI range support") added
GIC_IRQ_TYPE_PARTITION support for EPPI to gic_irq_domain_translate(),
and commit 52085d3f20 ("irqchip/gic-v3: Dynamically allocate PPI
partition descriptors") made the gic_data.ppi_descs array big enough for
EPPI, but neither gic_irq_domain_select() nor partition_domain_translate()
were updated.
This means partitions are created by partition_create_desc() for the
EPPI range, but can't be registered as they will always match the root
domain and map to the summary interrupt.
Update gic_irq_domain_select() to match PPI and EPPI. The fwspec for
PPI and EPPI both start from 0. Use gic_irq_domain_translate() to find
the hwirq from the fwspec, then convert this to a ppi index.
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729172748.28841-3-james.morse@arm.com
gic_get_ppi_index() is a useful concept for ppi partitions, as the GIC
has two PPI ranges but needs mapping to a single range when used as an
index in the gic_data.ppi_descs[] array.
Add a double-underscore version which takes just the intid. This will
be used in the partition domain select and translate helpers to enable
partition support for the EPPI range.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729172748.28841-2-james.morse@arm.com
Edge-triggered mode and level-triggered mode need different handlers,
and edge-triggered mode need a specific ack operation. So improve it.
Fixes: ef8c01eb64 ("irqchip: Add Loongson PCH PIC controller")
Signed-off-by: Chen Zhu <zhuchen@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210805132216.3539007-1-chenhuacai@loongson.cn
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-7-andriy.shevchenko@linux.intel.com
Switch to devm_bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-6-andriy.shevchenko@linux.intel.com
Switch to devm_bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-5-andriy.shevchenko@linux.intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-4-andriy.shevchenko@linux.intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-3-andriy.shevchenko@linux.intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-2-andriy.shevchenko@linux.intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-1-andriy.shevchenko@linux.intel.com
- Fix a MIPS bug where irqdomain loopkups could occur in a context
where RCU is not allowed
- Fix a documentation bug for handle_domain_irq
-----BEGIN PGP SIGNATURE-----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=eTw3
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Fix a MIPS bug where irqdomain loopkups could occur in a context
where RCU is not allowed
- Fix a documentation bug for handle_domain_irq
Since d4a45c68dc ("irqdomain: Protect the linear revmap with RCU"),
any irqdomain lookup requires the RCU read lock to be held.
This assumes that the architecture code will be structured such as
irq_enter() will be called *before* the interrupt is looked up
in the irq domain. However, this isn't the case for MIPS, and a number
of drivers are structured to do it the other way around when handling
an interrupt in their root irqchip (secondary irqchips are OK by
construction).
This results in a RCU splat on a lockdep-enabled kernel when the kernel
takes an interrupt from idle, as reported by Guenter Roeck.
Note that this could have fired previously if any driver had used
tree-based irqdomain, which always had the RCU requirement.
To solve this, provide a MIPS-specific helper (do_domain_IRQ())
as the pendent of do_IRQ() that will do thing in the right order
(and maybe save some cycles in the process).
Ideally, MIPS would be moved over to using handle_domain_irq(),
but that's much more ambitious.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
[maz: add dependency on CONFIG_IRQ_DOMAIN after report from the kernelci bot]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20210705172352.GA56304@roeck-us.net
Link: https://lore.kernel.org/r/20210706110647.3979002-1-maz@kernel.org
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which always
return IRQ_HANDLED which turns the spurious interrupt detection into a
pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level flow
handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=FIKh
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which
always return IRQ_HANDLED which turns the spurious interrupt
detection into a pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level
flow handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements"
* tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
dt-bindings: interrupt-controller: arm,gic-v3: Describe GICv3 optional properties
irqchip: gic-pm: Remove redundant error log of clock bulk
irqchip/sun4i: Remove unnecessary oom message
irqchip/irq-imx-gpcv2: Remove unnecessary oom message
irqchip/imgpdc: Remove unnecessary oom message
irqchip/gic-v3-its: Remove unnecessary oom message
irqchip/gic-v2m: Remove unnecessary oom message
irqchip/exynos-combiner: Remove unnecessary oom message
irqchip: Bulk conversion to generic_handle_domain_irq()
genirq: Move non-irqdomain handle_domain_irq() handling into ARM's handle_IRQ()
genirq: Add generic_handle_domain_irq() helper
irqchip/nvic: Convert from handle_IRQ() to handle_domain_irq()
irqdesc: Fix __handle_domain_irq() comment
genirq: Use irq_resolve_mapping() to implement __handle_domain_irq() and co
irqdomain: Introduce irq_resolve_mapping()
irqdomain: Protect the linear revmap with RCU
irqdomain: Cache irq_data instead of a virq number in the revmap
irqdomain: Use struct_size() helper when allocating irqdomain
irqdomain: Make normal and nomap irqdomains exclusive
powerpc: Move the use of irq_domain_add_nomap() behind a config option
...
- Add MTE support in guests, complete with tag save/restore interface
- Reduce the impact of CMOs by moving them in the page-table code
- Allow device block mappings at stage-2
- Reduce the footprint of the vmemmap in protected mode
- Support the vGIC on dumb systems such as the Apple M1
- Add selftest infrastructure to support multiple configuration
and apply that to PMU/non-PMU setups
- Add selftests for the debug architecture
- The usual crop of PMU fixes
PPC:
- Support for the H_RPT_INVALIDATE hypercall
- Conversion of Book3S entry/exit to C
- Bug fixes
S390:
- new HW facilities for guests
- make inline assembly more robust with KASAN and co
x86:
- Allow userspace to handle emulation errors (unknown instructions)
- Lazy allocation of the rmap (host physical -> guest physical address)
- Support for virtualizing TSC scaling on VMX machines
- Optimizations to avoid shattering huge pages at the beginning of live migration
- Support for initializing the PDPTRs without loading them from memory
- Many TLB flushing cleanups
- Refuse to load if two-stage paging is available but NX is not (this has
been a requirement in practice for over a year)
- A large series that separates the MMU mode (WP/SMAP/SMEP etc.) from
CR0/CR4/EFER, using the MMU mode everywhere once it is computed
from the CPU registers
- Use PM notifier to notify the guest about host suspend or hibernate
- Support for passing arguments to Hyper-V hypercalls using XMM registers
- Support for Hyper-V TLB flush hypercalls and enlightened MSR bitmap on
AMD processors
- Hide Hyper-V hypercalls that are not included in the guest CPUID
- Fixes for live migration of virtual machines that use the Hyper-V
"enlightened VMCS" optimization of nested virtualization
- Bugfixes (not many)
Generic:
- Support for retrieving statistics without debugfs
- Cleanups for the KVM selftests API
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmDV9UYUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOIRgf/XX8fKLh24RnTOs2ldIu2AfRGVrT4
QMrr8MxhmtukBAszk2xKvBt8/6gkUjdaIC3xqEnVjxaDaUvZaEtP7CQlF5JV45rn
iv1zyxUKucXrnIOr+gCioIT7qBlh207zV35ArKioP9Y83cWx9uAs22pfr6g+7RxO
h8bJZlJbSG6IGr3voANCIb9UyjU1V/l8iEHqRwhmr/A5rARPfD7g8lfMEQeGkzX6
+/UydX2fumB3tl8e2iMQj6vLVdSOsCkehvpHK+Z33EpkKhan7GwZ2sZ05WmXV/nY
QLAYfD10KegoNWl5Ay4GTp4hEAIYVrRJCLC+wnLdc0U8udbfCuTC31LK4w==
=NcRh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"This covers all architectures (except MIPS) so I don't expect any
other feature pull requests this merge window.
ARM:
- Add MTE support in guests, complete with tag save/restore interface
- Reduce the impact of CMOs by moving them in the page-table code
- Allow device block mappings at stage-2
- Reduce the footprint of the vmemmap in protected mode
- Support the vGIC on dumb systems such as the Apple M1
- Add selftest infrastructure to support multiple configuration and
apply that to PMU/non-PMU setups
- Add selftests for the debug architecture
- The usual crop of PMU fixes
PPC:
- Support for the H_RPT_INVALIDATE hypercall
- Conversion of Book3S entry/exit to C
- Bug fixes
S390:
- new HW facilities for guests
- make inline assembly more robust with KASAN and co
x86:
- Allow userspace to handle emulation errors (unknown instructions)
- Lazy allocation of the rmap (host physical -> guest physical
address)
- Support for virtualizing TSC scaling on VMX machines
- Optimizations to avoid shattering huge pages at the beginning of
live migration
- Support for initializing the PDPTRs without loading them from
memory
- Many TLB flushing cleanups
- Refuse to load if two-stage paging is available but NX is not (this
has been a requirement in practice for over a year)
- A large series that separates the MMU mode (WP/SMAP/SMEP etc.) from
CR0/CR4/EFER, using the MMU mode everywhere once it is computed
from the CPU registers
- Use PM notifier to notify the guest about host suspend or hibernate
- Support for passing arguments to Hyper-V hypercalls using XMM
registers
- Support for Hyper-V TLB flush hypercalls and enlightened MSR bitmap
on AMD processors
- Hide Hyper-V hypercalls that are not included in the guest CPUID
- Fixes for live migration of virtual machines that use the Hyper-V
"enlightened VMCS" optimization of nested virtualization
- Bugfixes (not many)
Generic:
- Support for retrieving statistics without debugfs
- Cleanups for the KVM selftests API"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (314 commits)
KVM: x86: rename apic_access_page_done to apic_access_memslot_enabled
kvm: x86: disable the narrow guest module parameter on unload
selftests: kvm: Allows userspace to handle emulation errors.
kvm: x86: Allow userspace to handle emulation errors
KVM: x86/mmu: Let guest use GBPAGES if supported in hardware and TDP is on
KVM: x86/mmu: Get CR4.SMEP from MMU, not vCPU, in shadow page fault
KVM: x86/mmu: Get CR0.WP from MMU, not vCPU, in shadow page fault
KVM: x86/mmu: Drop redundant rsvd bits reset for nested NPT
KVM: x86/mmu: Optimize and clean up so called "last nonleaf level" logic
KVM: x86: Enhance comments for MMU roles and nested transition trickiness
KVM: x86/mmu: WARN on any reserved SPTE value when making a valid SPTE
KVM: x86/mmu: Add helpers to do full reserved SPTE checks w/ generic MMU
KVM: x86/mmu: Use MMU's role to determine PTTYPE
KVM: x86/mmu: Collapse 32-bit PAE and 64-bit statements for helpers
KVM: x86/mmu: Add a helper to calculate root from role_regs
KVM: x86/mmu: Add helper to update paging metadata
KVM: x86/mmu: Don't update nested guest's paging bitmasks if CR0.PG=0
KVM: x86/mmu: Consolidate reset_rsvds_bits_mask() calls
KVM: x86/mmu: Use MMU role_regs to get LA57, and drop vCPU LA57 helper
KVM: x86/mmu: Get nested MMU's root level from the MMU's role
...
- Fix GICv3 NMI handling where an IRQ could be mistakenly handled
as a NMI, with disatrous effects
-----BEGIN PGP SIGNATURE-----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=yKDo
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Fix GICv3 NMI handling where an IRQ could be mistakenly handled
as a NMI, with disatrous effects
Link: https://lore.kernel.org/r/20210610171127.2404752-1-maz@kernel.org
Various minor irqchip driver updates:
- QC PDC now compiles as a module
- HiSilicon MBIGEN fix for compile-time warning when !ACPI
* irq/irqchip-driver-updates:
irqchip/mbigen: Fix compile warning when CONFIG_ACPI is disabled
irqchip/qcom-pdc: Switch to IRQCHIP_PLATFORM_DRIVER and allow as a module
Simplify the handling of interrupts that require an IRQ domain
resolution:
- domains now cache the irqdata instead of the irq number
- consistent behaviour wrt RCU
- single lookup for architectures using sparse IRQs
- reduced boilerplate code in drivers.
* irq/generic_handle_domain_irq-core: (26 commits)
irqchip: Bulk conversion to generic_handle_domain_irq()
genirq: Move non-irqdomain handle_domain_irq() handling into ARM's handle_IRQ()
genirq: Add generic_handle_domain_irq() helper
irqchip/nvic: Convert from handle_IRQ() to handle_domain_irq()
irqdesc: Fix __handle_domain_irq() comment
genirq: Use irq_resolve_mapping() to implement __handle_domain_irq() and co
irqdomain: Introduce irq_resolve_mapping()
irqdomain: Protect the linear revmap with RCU
irqdomain: Cache irq_data instead of a virq number in the revmap
irqdomain: Use struct_size() helper when allocating irqdomain
irqdomain: Make normal and nomap irqdomains exclusive
powerpc: Move the use of irq_domain_add_nomap() behind a config option
irqdomain: Reimplement irq_linear_revmap() with irq_find_mapping()
irqdomain: Kill irq_domain_add_legacy_isa
powerpc: Drop dependency between asm/irq.h and linux/irqdomain.h
powerpc: Convert irq_domain_add_legacy_isa use to irq_domain_add_legacy
scsi/ibmvscsi: Directly include linux/{of.h,irqdomain.h}
powerpc: Add missing linux/{of.h,irqdomain.h} include directives
MIPS: Do not include linux/irqdomain.h from asm/irq.h
MIPS: Add missing linux/irqdomain.h includes
...
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609141428.14737-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609141150.14637-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140828.14584-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140643.14531-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140534.14478-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140335.14425-1-thunder.leizhen@huawei.com
The arm64 entry code suffers from an annoying issue on taking
a NMI, as it sets PMR to a value that actually allows IRQs
to be acknowledged. This is done for consistency with other parts
of the code, and is in the process of being fixed. This shouldn't
be a problem, as we are not enabling interrupts whilst in NMI
context.
However, in the infortunate scenario that we took a spurious NMI
(retired before the read of IAR) *and* that there is an IRQ pending
at the same time, we'll ack the IRQ in NMI context. Too bad.
In order to avoid deadlocks while running something like perf,
teach the GICv3 driver about this situation: if we were in
a context where no interrupt should have fired, transiently
set PMR to a value that only allows NMIs before acking the pending
interrupt, and restore the original value after that.
This papers over the core issue for the time being, and makes
NMIs great again. Sort of.
Fixes: 4d6a38da8e ("arm64: entry: always set GIC_PRIO_PSR_I_SET during entry")
Co-developed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/lkml/20210610145731.1350460-1-maz@kernel.org
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Given that the nvic driver is fully irqdomain aware, there is no
reason for it to use the arch-specific handle_IRQ(), and it can
be moved over to handle_domain_irq().
Signed-off-by: Marc Zyngier <maz@kernel.org>
This drivers currently obtains linux/irqdomain.h by luck and
a chain of bizarre inclusions, which we're about to fix.
Let's include the required file directly.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fix the following compile warning:
drivers/irqchip/irq-mbigen.c:372:36: warning: ‘mbigen_acpi_match’ defined but not used [-Wunused-const-variable=]
static const struct acpi_device_id mbigen_acpi_match[] = {
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210519050455.1693953-1-yangyingliang@huawei.com
This patch revives changes from Saravana Kannan to switch the
qcom-pdc driver to use IRQCHIP_PLATFORM_DRIVER helper macros,
and allows qcom-pdc driver to be loaded as a permanent module.
Earlier attempts at this ran into trouble with loading
dependencies, but with Saravana's fw_devlink=on set by default
now we should avoid those.
[jstultz: Folded in with my changes to allow the driver to be
loadable as a permenent module]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210518211922.3474368-1-john.stultz@linaro.org
The CPUs in the Apple M1 SoC partially implement a virtual GICv3
CPU interface, although one that is incapable of HW deactivation
of interrupts, nor masking the maintenance interrupt.
Advertise the support to KVM.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The vGIC advertising code is unsurprisingly very much tied to
the GIC implementations. However, we are about to extend the
support to lesser implementations.
Let's dissociate the vgic registration from the GIC code and
move it into KVM, where it makes a bit more sense. This also
allows us to mark the gic_kvm_info structures as __initdata.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210511125428.6108-2-thunder.leizhen@huawei.com
The Apple Interrupt Controller is only present on Apple Silicon SoCs.
Hence add a dependency on ARCH_APPLE, to prevent asking the user about
this driver when configuring a kernel without Apple Silicon SoC support.
Drop the default, as ARCH_APPLE already selects APPLE_AIC.
Fixes: 76cde26394 ("irqchip/apple-aic: Add support for the Apple Interrupt Controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/f37e8daea37d50651d2164b0b3dad90780188548.1618316398.git.geert+renesas@glider.be
- Stage-2 isolation for the host kernel when running in protected mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation,
zap under read lock, enable/disably dirty page logging under
read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing
the architecture-specific code
- Some selftests improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmCJ13kUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroM1HAgAqzPxEtiTPTFeFJV5cnPPJ3dFoFDK
y/juZJUQ1AOtvuWzzwuf175ewkv9vfmtG6rVohpNSkUlJYeoc6tw7n8BTTzCVC1b
c/4Dnrjeycr6cskYlzaPyV6MSgjSv5gfyj1LA5UEM16LDyekmaynosVWY5wJhju+
Bnyid8l8Utgz+TLLYogfQJQECCrsU0Wm//n+8TWQgLf1uuiwshU5JJe7b43diJrY
+2DX+8p9yWXCTz62sCeDWNahUv8AbXpMeJ8uqZPYcN1P0gSEUGu8xKmLOFf9kR7b
M4U1Gyz8QQbjd2lqnwiWIkvRLX6gyGVbq2zH0QbhUe5gg3qGUX7JjrhdDQ==
=AXUi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"This is a large update by KVM standards, including AMD PSP (Platform
Security Processor, aka "AMD Secure Technology") and ARM CoreSight
(debug and trace) changes.
ARM:
- CoreSight: Add support for ETE and TRBE
- Stage-2 isolation for the host kernel when running in protected
mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- AMD PSP driver changes
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation, zap under
read lock, enable/disably dirty page logging under read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing the
architecture-specific code
- a handful of "Get rid of oprofile leftovers" patches
- Some selftests improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (379 commits)
KVM: selftests: Speed up set_memory_region_test
selftests: kvm: Fix the check of return value
KVM: x86: Take advantage of kvm_arch_dy_has_pending_interrupt()
KVM: SVM: Skip SEV cache flush if no ASIDs have been used
KVM: SVM: Remove an unnecessary prototype declaration of sev_flush_asids()
KVM: SVM: Drop redundant svm_sev_enabled() helper
KVM: SVM: Move SEV VMCB tracking allocation to sev.c
KVM: SVM: Explicitly check max SEV ASID during sev_hardware_setup()
KVM: SVM: Unconditionally invoke sev_hardware_teardown()
KVM: SVM: Enable SEV/SEV-ES functionality by default (when supported)
KVM: SVM: Condition sev_enabled and sev_es_enabled on CONFIG_KVM_AMD_SEV=y
KVM: SVM: Append "_enabled" to module-scoped SEV/SEV-ES control variables
KVM: SEV: Mask CPUID[0x8000001F].eax according to supported features
KVM: SVM: Move SEV module params/variables to sev.c
KVM: SVM: Disable SEV/SEV-ES if NPT is disabled
KVM: SVM: Free sev_asid_bitmap during init if SEV setup fails
KVM: SVM: Zero out the VMCB array used to track SEV ASID association
x86/sev: Drop redundant and potentially misleading 'sev_enabled'
KVM: x86: Move reverse CPUID helpers to separate header file
KVM: x86: Rename GPR accessors to make mode-aware variants the defaults
...
- removed broken/unmaintained MIPS KVM trap and emulate support
- added support for Loongson-2K1000
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=w/c4
-----END PGP SIGNATURE-----
Merge tag 'mips_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed get_fs/set_fs
- removed broken/unmaintained MIPS KVM trap and emulate support
- added support for Loongson-2K1000
- fixes and cleanups
* tag 'mips_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (107 commits)
MIPS: BCM63XX: Use BUG_ON instead of condition followed by BUG.
MIPS: select ARCH_KEEP_MEMBLOCK unconditionally
mips: Do not include hi and lo in clobber list for R6
MIPS:DTS:Correct the license for Loongson-2K
MIPS:DTS:Fix label name and interrupt number of ohci for Loongson-2K
MIPS: Avoid handcoded DIVU in `__div64_32' altogether
lib/math/test_div64: Correct the spelling of "dividend"
lib/math/test_div64: Fix error message formatting
mips/bootinfo:correct some comments of fw_arg
MIPS: Avoid DIVU in `__div64_32' is result would be zero
MIPS: Reinstate platform `__div64_32' handler
div64: Correct inline documentation for `do_div'
lib/math: Add a `do_div' test module
MIPS: Makefile: Replace -pg with CC_FLAGS_FTRACE
MIPS: pci-legacy: revert "use generic pci_enable_resources"
MIPS: Loongson64: Add kexec/kdump support
MIPS: pci-legacy: use generic pci_enable_resources
MIPS: pci-legacy: remove busn_resource field
MIPS: pci-legacy: remove redundant info messages
MIPS: pci-legacy: stop using of_pci_range_to_resource
...
The Apple M1 is the processor used it all current generation Apple
Macintosh computers. Support for this platform so far is rudimentary,
but it boots and can use framebuffer and serial console over a special
USB cable.
Support for several essential on-chip devices (USB, PCIe, IOMMU, NVMe)
is work in progress but was not ready in time.
A very detailed description of what works is in the merge commit
and on the AsahiLinux wiki.
Link: https://lore.kernel.org/linux-arm-kernel/bdb18e9f-fcd7-1e31-2224-19c0e5090706@marcan.st/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=pBZy
-----END PGP SIGNATURE-----
Merge tag 'arm-apple-m1-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Apple M1 platform support from Arnd Bergmann:
"The Apple M1 is the processor used it all current generation Apple
Macintosh computers. Support for this platform so far is rudimentary,
but it boots and can use framebuffer and serial console over a special
USB cable.
Support for several essential on-chip devices (USB, PCIe, IOMMU, NVMe)
is work in progress but was not ready in time.
A very detailed description of what works is in the commit message of
commit 1bb2fd3880 ("Merge tag 'm1-soc-bringup-v5' [..]") and on the
AsahiLinux wiki"
Link: https://lore.kernel.org/linux-arm-kernel/bdb18e9f-fcd7-1e31-2224-19c0e5090706@marcan.st/
* tag 'arm-apple-m1-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
asm-generic/io.h: Unbork ioremap_np() declaration
arm64: apple: Add initial Apple Mac mini (M1, 2020) devicetree
dt-bindings: display: Add apple,simple-framebuffer
arm64: Kconfig: Introduce CONFIG_ARCH_APPLE
irqchip/apple-aic: Add support for the Apple Interrupt Controller
dt-bindings: interrupt-controller: Add DT bindings for apple-aic
arm64: Move ICH_ sysreg bits from arm-gic-v3.h to sysreg.h
of/address: Add infrastructure to declare MMIO as non-posted
asm-generic/io.h: implement pci_remap_cfgspace using ioremap_np
arm64: Implement ioremap_np() to map MMIO as nGnRnE
docs: driver-api: device-io: Document ioremap() variants & access funcs
docs: driver-api: device-io: Document I/O access functions
asm-generic/io.h: Add a non-posted variant of ioremap()
arm64: arch_timer: Implement support for interrupt-names
dt-bindings: timer: arm,arch_timer: Add interrupt-names support
arm64: cputype: Add CPU implementor & types for the Apple M1 cores
dt-bindings: arm: cpus: Add apple,firestorm & icestorm compatibles
dt-bindings: arm: apple: Add bindings for Apple ARM platforms
dt-bindings: vendor-prefixes: Add apple prefix
New HW support:
- New driver for the Nuvoton WPCM450 interrupt controller
- New driver for the IDT 79rc3243x interrupt controller
- Add support for interrupt trigger configuration to the MStar irqchip
- Add more external interrupt support to the STM32 irqchip
- Add new compatible strings for QCOM SC7280 to the qcom-pdc binding
Fixes and cleanups:
- Drop irq_create_strict_mappings() and irq_create_identity_mapping()
from the irqdomain API, with cleanups in a couple of drivers
- Fix nested NMI issue with spurious interrupts on GICv3
- Don't allow GICv4.1 vSGIs when the CPU doesn't support them
- Various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=RqVj
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip and irqdomain updates from Marc Zyngier:
New HW support:
- New driver for the Nuvoton WPCM450 interrupt controller
- New driver for the IDT 79rc3243x interrupt controller
- Add support for interrupt trigger configuration to the MStar irqchip
- Add more external interrupt support to the STM32 irqchip
- Add new compatible strings for QCOM SC7280 to the qcom-pdc binding
Fixes and cleanups:
- Drop irq_create_strict_mappings() and irq_create_identity_mapping()
from the irqdomain API, with cleanups in a couple of drivers
- Fix nested NMI issue with spurious interrupts on GICv3
- Don't allow GICv4.1 vSGIs when the CPU doesn't support them
- Various cleanups and minor fixes
Link: https://lore.kernel.org/r/20210424094640.1731920-1-maz@kernel.org
Previously the XILINX_INTC config option was hidden and only
auto-selected on the MicroBlaze platform. However, this IP can also be
used on the Zynq and ZynqMP platforms as a secondary cascaded
controller. Allow this option to be user-enabled on those platforms.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210423185853.2556087-1-robert.hancock@calian.com
IDT 79rc3243x SoCs have rather simple interrupt controllers connected
to the MIPS CPU interrupt lines. Each of them has room for up to
32 interrupts.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210422145330.73452-1-tsbogend@alpha.franken.de
GIC CPU interfaces versions predating GIC v4.1 were not built to
accommodate vINTID within the vSGI range; as reported in the GIC
specifications (8.2 "Changes to the CPU interface"), it is
CONSTRAINED UNPREDICTABLE to deliver a vSGI to a PE with
ID_AA64PFR0_EL1.GIC < b0011.
Check the GIC CPUIF version by reading the SYS_ID_AA64_PFR0_EL1.
Disable vSGIs if a CPUIF version < 4.1 is detected to prevent using
vSGIs on systems where they may misbehave.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210317100719.3331-2-lorenzo.pieralisi@arm.com
Use the 'fallthrough' macro to document that this switch case
does indeed fall through to the next case.
../drivers/irqchip/irq-tb10x.c: In function 'tb10x_irq_set_type':
../drivers/irqchip/irq-tb10x.c:62:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
62 | flow_type = IRQ_TYPE_LEVEL_LOW;
../drivers/irqchip/irq-tb10x.c:63:2: note: here
63 | case IRQ_TYPE_LEVEL_LOW:
| ^~~~
Fixes: b06eb0173e ("irqchip: Add TB10x interrupt controller driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210422051620.23021-1-rdunlap@infradead.org
This is the root interrupt controller used on Apple ARM SoCs such as the
M1. This irqchip driver performs multiple functions:
* Handles both IRQs and FIQs
* Drives the AIC peripheral itself (which handles IRQs)
* Dispatches FIQs to downstream hard-wired clients (currently the ARM
timer).
* Implements a virtual IPI multiplexer to funnel multiple Linux IPIs
into a single hardware IPI
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
This driver is (for now) ARM specific, and currently doesn't
build with a variety of architectures (ia64, RISC-V, x86_64
at the very least).
Drop COMPILE_TEST from Kconfig until it gets sorted out.
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Support irq polarity configuration and save and restore the config
when system suspend and resume.
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
[maz: fixed irq_set_type callback]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210315131848.31840-1-mark-pk.tsai@mediatek.com
The WPCM450 AIC ("Advanced Interrupt Controller") is the interrupt
controller found in the Nuvoton WPCM450 SoC and other Winbond/Nuvoton
SoCs.
The list of registers if based on the AMI vendor kernel and the
Nuvoton W90N745 datasheet.
Although the hardware supports other interrupt modes, the driver only
supports high-level interrupts at the moment, because other modes could
not be tested so far.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210406120921.2484986-7-j.neuschaefer@gmx.net
Add following usart instances exti direct event support (used for UART wake
up).
- exti 26 (USART1) is mapped to GIC 37
- exti 27 (USART2) is mapped to GIC 38
- exti 28 (USART3) is mapped to GIC 39
- exti 29 (USART6) is mapped to GIC 71
- exti 31 (UART5) is mapped to GIC 53
- exti 32 (UART7) is mapped to GIC 82
- exti 33 (UART8) is mapped to GIC 83
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210319184253.5841-4-erwan.leray@foss.st.com
When building with extra warnings enabled, clang points out a
mistake in the error handling:
drivers/irqchip/irq-gic-v3-mbi.c:306:21: error: result of comparison of constant 18446744073709551615 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (mbi_phys_base == OF_BAD_ADDR) {
Truncate the constant to the same type as the variable it gets compared
to, to shut make the check work and void the warning.
Fixes: 505287525c ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323131842.2773094-1-arnd@kernel.org
All of these two are never modified after init, so they can be
__ro_after_init.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210330020911.26423e9e@xhacker
Add IO interrupt controller support for Loongson-2K1000, different
from the Loongson-3A series is that Loongson-2K1000 has 64 interrupt
sources, 0-31 correspond to the device tree liointc0 device node, and
the other correspond to liointc1 node.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Tested-by: Ming Wang <wangming01@loongson.cn>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
GICv4.1 gives a way to get the VLPI state, which needs to map the
vPE first, and after the state read, we may remap the vPE back while
the VPT is not empty. So we can't assume that the VPT is empty at
the first map. Besides, the optimization of PTZ is probably limited
since the HW should be fairly efficient to parse the empty VPT. Let's
drop the setting of PTZ altogether.
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210322060158.1584-3-lushenming@huawei.com
In order to be able to manipulate the VPT once a vPE has been
unmapped, perform the required CMO to invalidate the CPU view
of the VPT.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Link: https://lore.kernel.org/r/20210322060158.1584-2-lushenming@huawei.com
The purpose of separating loongson_system_configuration from boot_param.h
is to keep the other structure consistent with the firmware.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the interrupt controller found in the JZ4760 SoC, which
works exactly like the one in the JZ4770.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210307172014.73481-2-paul@crapouillou.net
Implementing CONFIG_GENERIC_IRQ_MULTI_HANDLER is a decision that is
made at the architecture level, and shouldn't involve the irqchip
at all (we even provide a fallback helper when the option isn't
selected).
Drop all instances of such selection from non-arch code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210217142800.2547737-1-maz@kernel.org
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Hector Martin <marcan@marcan.st>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- New driver for the MIPS-based Realtek RTL838x/RTL839x SoC
- Conversion of the sun6i-r support code to a hierarchical setup
- Fix wake-up interrupts for the ls-extirq driver
- Fix MSI allocation for the loongson-pch-msi driver
- Add compatible strings for new Qualcomm SoCs
- Tidy up a few Kconfig entries (IMX, CSKY)
- Spelling phyksiz
- Remove the sirfsoc and tango drivers
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAmApGDMPHG1hekBrZXJu
ZWwub3JnAAoJECPQ0LrRPXpDcucP/RXS6lW9uTfTUudLIib/YTHNZ7uTuVZrfX+K
4OEAPZKkRDlsSuWvr5i98da0DM0yw0B06c62oNuw7sex6JXsO/2FYISDskUZnlYZ
+ApdQGHhVL+kAOHubepYrZLXf7hPX6N/kZotnq1GU0VY1JhxBkVj6sVFJKEnOwf/
sUwDO2+XvmjgrdXRyZgjsyz71SXQ8OosAIsLAI9UHIB/mHi9R3oItEJD7xANeunp
IsNelUAnqBPN7/OuyeThh2SGxVXVBtja9mRd+AN7HrDmocxnYnsgMQDR/cEO2aTw
xdeKQbEnViUK0JXkofIPwkck58ceUkAl8LLqe0tHPfQgkoPVE9diBrqrP4df7999
NIhPYe2kjZ3+DDNK0zAkvKHiHXC7VPl2qGoqqIUX10x1M+BNxfMSYXgjM4PNK7p7
Ey0w43hnvNKQp7y7ubf+BMStXEOPd4pwyt1P713mSbxeX9sSwGwffI26o58tVpHA
zmoaL5MULWQPFCnznN3yaoBf57hNrkCmXR5lZLwD30VN8m5pJshduvO+rE+6LUgI
DMQPWpCNToKDd0xxnrnMuf/XjOunNSrX0wt9xtuwmpw5gwlpJp2m9TyZ6Xa5M3rl
PYwnVr9gWwGSMw9+G0Ky+C2s+SBzRrPDLfkDOODaGflP/t1b0S8K+1vuIqUHH8fz
2DBWttJp
=hhRV
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier
- New driver for the MIPS-based Realtek RTL838x/RTL839x SoC
- Conversion of the sun6i-r support code to a hierarchical setup
- Fix wake-up interrupts for the ls-extirq driver
- Fix MSI allocation for the loongson-pch-msi driver
- Add compatible strings for new Qualcomm SoCs
- Tidy up a few Kconfig entries (IMX, CSKY)
- Spelling phyksiz
- Remove the sirfsoc and tango drivers
Link: https://lore.kernel.org/r/20210214124015.3333457-1-maz@kernel.org
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of IMX_INTMUX to ARCH_MXC,
and ask the user in case of compile-testing.
Fixes: 66968d7dfc ("irqchip: Add COMPILE_TEST support for IMX_INTMUX")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210208145605.422943-1-geert+renesas@glider.be
Currently we use bitmap_alloc() to allocate msi bitmap which should be
initialized with zero. This is obviously wrong but it works because msi
can fallback to legacy interrupt mode. So use bitmap_zalloc() instead.
Fixes: 632dcc2c75 ("irqchip: Add Loongson PCH MSI controller")
Cc: stable@vger.kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210209071051.2078435-1-chenhuacai@loongson.cn
The irq-csky-mpintc driver is only supported on CPU_CK860 and
it will generate a compilation error when selected with CPU_CK610.
As it is already selected directly in the architecture Kconfig,
drop the option to select it manually.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
[maz: rewrote commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210204074609.3553018-1-guoren@kernel.org
This is a standard IRQ driver with only status and mask registers.
The mapping from SoC interrupts (18-31) to MIPS core interrupts is
done via an interrupt-map in device tree.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210122204224.509124-3-bert@biot.com
The ls-extirq driver doesn't implement the irq_set_wake()
callback, while being wake-up capable. This results in
ugly behaviours across suspend/resume cycles.
Advertise this by adding IRQCHIP_SKIP_SET_WAKE to
the irqchip flags
Fixes: b16a1caf46 ("irqchip/ls-extirq: Add LS1043A, LS1088A external interrupt support")
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210129095034.33821-1-biwen.li@oss.nxp.com
Maintain bitmaps of wake-enabled IRQs and mux inputs, and program them
to the hardware during the syscore phase of suspend and shutdown. Then
restore the original set of enabled IRQs (only the NMI) during resume.
This serves two purposes. First, it lets power management firmware
running on the ARISC coprocessor know which wakeup sources Linux wants
to have enabled. That way, it can avoid turning them off when it shuts
down the remainder of the clock tree. Second, it preconfigures the
coprocessor's interrupt controller, so the firmware's wakeup logic
is as simple as waiting for an interrupt to arrive.
The suspend/resume logic is not conditional on PM_SLEEP because it is
identical to the init/shutdown logic. Wake IRQs may be enabled during
shutdown to allow powering the board back on. As an example, see
commit a5c5e50cce ("Input: gpio-keys - add shutdown callback").
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210118055040.21910-5-samuel@sholland.org
The R_INTC in the A31 and newer sun8i/sun50i SoCs is more similar to the
original sun4i interrupt controller than the sun7i/sun9i NMI controller.
It is used for two distinct purposes:
- To control the trigger, latch, and mask for the NMI input pin
- To provide the interrupt input for the ARISC coprocessor
As this interrupt controller is not documented, information about it
comes from vendor-provided firmware blobs and from experimentation.
Differences from the sun4i interrupt controller appear to be:
- It only has one or two registers of each kind (max 32 or 64 IRQs)
- Multiplexing logic is added to support additional inputs
- There is no FIQ-related logic
- There is no interrupt priority logic
In order to fulfill its two purposes, this hardware block combines four
types of IRQs. First, the NMI pin is routed to the "IRQ 0" input on this
chip, with a trigger type controlled by the NMI_CTRL_REG. The "IRQ 0
pending" output from this chip, if enabled, is then routed to a SPI IRQ
input on the GIC. In other words, bit 0 of IRQ_ENABLE_REG *does* affect
the NMI IRQ seen at the GIC.
The NMI is followed by a contiguous block of 15 "direct" (my name for
them) IRQ inputs that are connected in parallel to both R_INTC and the
GIC. Or in other words, these bits of IRQ_ENABLE_REG *do not* affect the
IRQs seen at the GIC.
Following the direct IRQs are the ARISC's copy of banked IRQs for shared
peripherals. These are not relevant to Linux. The remaining IRQs are
connected to a multiplexer and provide access to the first (up to) 128
SPIs from the ARISC. This range of SPIs overlaps with the direct IRQs.
Because of the 1:1 correspondence between R_INTC and GIC inputs, this is
a perfect scenario for using a stacked irqchip driver. We want to hook
into setting the NMI trigger type, but not actually handle any IRQ here.
To allow access to all multiplexed IRQs, this driver requires a new
binding where the interrupt number matches the GIC interrupt number.
(This moves the NMI from number 0 to 32 or 96, depending on the SoC.)
For simplicity, copy the three-cell GIC binding; this disambiguates
interrupt 0 in the old binding (the NMI) from interrupt 0 in the new
binding (SPI 0) by the number of cells.
Since R_INTC is in the always-on power domain, and its output is visible
to the power management coprocessor, a stacked irqchip driver provides a
simple way to add wakeup support to any of its IRQs. That is the next
patch; for now, just the NMI is moved over.
This commit mostly reverts commit 173bda53b3 ("irqchip/sunxi-nmi:
Support sun6i-a31-r-intc compatible").
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210118055040.21910-4-samuel@sholland.org
The GICv3 driver explanation related to PMR/RPR and SCR_EL3.FIQ
secure/non-secure priority handling contains a couple of typos.
Fix them.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210121182252.29320-1-lorenzo.pieralisi@arm.com
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210120133008.2421897-3-arnd@kernel.org
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210120133008.2421897-2-arnd@kernel.org
Since commit 5556797662 ("genirq/irqdomain: Allow partial trimming of
irq_data hierarchy") the irq_data chain is valided.
The irq_domain_trim_hierarchy() function doesn't consider the irq + ipi
domain hierarchy as valid, since the ipi domain has the irq domain set
as parent, but the parent domain has no chip set. Hence the boot ends in
a kernel panic.
Set the chip for the parent domain as it is done in the mips gic irq
driver, to have a valid irq_data chain.
Fixes: 3838a547fd ("irqchip: mips-cpu: Introduce IPI IRQ domain support")
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210107213603.1637781-1-dev@kresin.me
The TI PRUSS INTC irqchip driver handles the local interrupt controller
which is a child device of it's parent PRUSS/ICSSG device. The driver
was upstreamed in parallel with the PRUSS platform driver, and was
configurable independently previously. The PRUSS interrupt controller
is an integral part of the overall PRUSS software architecture, and is
not useful at all by itself.
Simplify the TI_PRUSS_INTC Kconfig dependencies by making it silent and
selected automatically when the TI_PRUSS platform driver is enabled.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210108162901.6003-1-s-anna@ti.com
* PSCI relay at EL2 when "protected KVM" is enabled
* New exception injection code
* Simplification of AArch32 system register handling
* Fix PMU accesses when no PMU is enabled
* Expose CSV3 on non-Meltdown hosts
* Cache hierarchy discovery fixes
* PV steal-time cleanups
* Allow function pointers at EL2
* Various host EL2 entry cleanups
* Simplification of the EL2 vector allocation
s390:
* memcg accouting for s390 specific parts of kvm and gmap
* selftest for diag318
* new kvm_stat for when async_pf falls back to sync
x86:
* Tracepoints for the new pagetable code from 5.10
* Catch VFIO and KVM irqfd events before userspace
* Reporting dirty pages to userspace with a ring buffer
* SEV-ES host support
* Nested VMX support for wait-for-SIPI activity state
* New feature flag (AVX512 FP16)
* New system ioctl to report Hyper-V-compatible paravirtualization features
Generic:
* Selftest improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl/bdL4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNgQQgAnTH6rhXa++Zd5F0EM2NwXwz3iEGb
lOq1DZSGjs6Eekjn8AnrWbmVQr+CBCuGU9MrxpSSzNDK/awryo3NwepOWAZw9eqk
BBCVwGBbJQx5YrdgkGC0pDq2sNzcpW/VVB3vFsmOxd9eHblnuKSIxEsCCXTtyqIt
XrLpQ1UhvI4yu102fDNhuFw2EfpzXm+K0Lc0x6idSkdM/p7SyeOxiv8hD4aMr6+G
bGUQuMl4edKZFOWFigzr8NovQAvDHZGrwfihu2cLRYKLhV97QuWVmafv/yYfXcz2
drr+wQCDNzDOXyANnssmviazrhOX0QmTAhbIXGGX/kTxYKcfPi83ZLoI3A==
=ISud
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Much x86 work was pushed out to 5.12, but ARM more than made up for it.
ARM:
- PSCI relay at EL2 when "protected KVM" is enabled
- New exception injection code
- Simplification of AArch32 system register handling
- Fix PMU accesses when no PMU is enabled
- Expose CSV3 on non-Meltdown hosts
- Cache hierarchy discovery fixes
- PV steal-time cleanups
- Allow function pointers at EL2
- Various host EL2 entry cleanups
- Simplification of the EL2 vector allocation
s390:
- memcg accouting for s390 specific parts of kvm and gmap
- selftest for diag318
- new kvm_stat for when async_pf falls back to sync
x86:
- Tracepoints for the new pagetable code from 5.10
- Catch VFIO and KVM irqfd events before userspace
- Reporting dirty pages to userspace with a ring buffer
- SEV-ES host support
- Nested VMX support for wait-for-SIPI activity state
- New feature flag (AVX512 FP16)
- New system ioctl to report Hyper-V-compatible paravirtualization features
Generic:
- Selftest improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (171 commits)
KVM: SVM: fix 32-bit compilation
KVM: SVM: Add AP_JUMP_TABLE support in prep for AP booting
KVM: SVM: Provide support to launch and run an SEV-ES guest
KVM: SVM: Provide an updated VMRUN invocation for SEV-ES guests
KVM: SVM: Provide support for SEV-ES vCPU loading
KVM: SVM: Provide support for SEV-ES vCPU creation/loading
KVM: SVM: Update ASID allocation to support SEV-ES guests
KVM: SVM: Set the encryption mask for the SVM host save area
KVM: SVM: Add NMI support for an SEV-ES guest
KVM: SVM: Guest FPU state save/restore not needed for SEV-ES guest
KVM: SVM: Do not report support for SMM for an SEV-ES guest
KVM: x86: Update __get_sregs() / __set_sregs() to support SEV-ES
KVM: SVM: Add support for CR8 write traps for an SEV-ES guest
KVM: SVM: Add support for CR4 write traps for an SEV-ES guest
KVM: SVM: Add support for CR0 write traps for an SEV-ES guest
KVM: SVM: Add support for EFER write traps for an SEV-ES guest
KVM: SVM: Support string IO operations for an SEV-ES guest
KVM: SVM: Support MMIO for an SEV-ES guest
KVM: SVM: Create trace events for VMGEXIT MSR protocol processing
KVM: SVM: Create trace events for VMGEXIT processing
...
It appears that despite its name, the bcm2836_arm_irqchip_ipi_eoi()
callback is an acknowledgement, and not an EOI. This means that
we lose IPIs that are made pending between the handling of the
IPI and the write to LOCAL_MAILBOX0_CLR0. With the right timing,
things fail nicely.
This used to work with handle_percpu_devid_fasteoi_ipi(), which
started by eoi-ing the interrupt. With the standard fasteoi flow,
this doesn't work anymore.
So let's use this callback for what it is, an ack. Your favourite
RPi-2/3 is back up and running.
Fixes: ffdad793d5 ("irqchip/bcm2836: Make IPIs use handle_percpu_devid_irq()")
Cc: Valentin Schneider <valentin.schneider@arm.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/c9fb4ab3-a5cb-648c-6de3-c6a871e60870@roeck-us.net
We have a problem if we use gpio-keys and configure wakeups such that
we only want one edge to wake us up. AKA:
wakeup-event-action = <EV_ACT_DEASSERTED>;
wakeup-source;
Specifically we end up with a phantom interrupt that blocks suspend if
the line was already high and we want wakeups on rising edges (AKA we
want the GPIO to go low and then high again before we wake up). The
opposite is also problematic.
Specifically, here's what's happening today:
1. Normally, gpio-keys configures to look for both edges. Due to the
current workaround introduced in commit c3c0c2e18d ("pinctrl:
qcom: Handle broken/missing PDC dual edge IRQs on sc7180"), if the
line was high we'd configure for falling edges.
2. At suspend time, we change to look for rising edges.
3. After qcom_pdc_gic_set_type() runs, we get a phantom interrupt.
We can solve this by just clearing the phantom interrupt.
NOTE: it is possible that this could cause problems for a client with
very specific needs, but there's not much we can do with this
hardware. As an example, let's say the interrupt signal is currently
high and the client is looking for falling edges. The client now
changes to look for rising edges. The client could possibly expect
that if the line has a short pulse low (and back high) that it would
always be detected. Specifically no matter when the pulse happened,
it should either have tripped the (old) falling edge trigger or the
(new) rising edge trigger. We will simply not trip it. We could
narrow down the race a bit by polling our parent before changing
types, but no matter what we do there will still be a period of time
where we can't tell the difference between a real transition (or more
than one transition) and the phantom.
Fixes: f55c73aef8 ("irqchip/pdc: Add PDC interrupt controller for QCOM SoCs")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201211141514.v4.1.I2702919afc253e2a451bebc3b701b462b2d22344@changeid
An aliasing PCI bridge is another case where we should flag the
corresponding allocation as "proxied", as MSIs are coming with
the bridge's RID, and not the originating device's.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20201129135208.680293-4-maz@kernel.org
The ITS already has some notion of "shared" devices. Let's map the
MSI_ALLOC_FLAGS_PROXY_DEVICE flag onto this internal property.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20201129135208.680293-3-maz@kernel.org
ti_sci_intr_irq_domain_free() assumes that out_irq of intr is stored in
data->chip_data and uses it for calling ti_sci irq_free() and then
mark the out_irq as available resource. But ti_sci_intr_irq_domain_alloc()
is storing p_hwirq(parent's hardware irq) which is translated from out_irq.
This is causing resource leakage and eventually out_irq resources might
be exhausted. Fix ti_sci_intr_irq_domain_alloc() by storing the out_irq
in data->chip_data.
Fixes: a5b659bd4b ("irqchip/ti-sci-intr: Add support for INTR being a parent to INTR")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201102120631.11165-1-lokeshvutla@ti.com
On a successful probe, the driver tries to print a success message with
INTA device id. It uses pdev->id for printing the id but id is stored in
inta->ti_sci_id. Fix it by correcting the dev_info parameter.
Fixes: 5c4b585d29 ("irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201102120614.11109-1-lokeshvutla@ti.com
NPS platform has been removed from ARC port and there are no in-tree
users of it now. So RIP !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20201105212210.1891598-3-vgupta@synopsys.com
As done for the Arm GIC irqchips, move IPIs to handle_percpu_devid_irq() as
handle_percpu_devid_fasteoi_ipi() isn't actually required.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201109094121.29975-5-valentin.schneider@arm.com
As done for the Arm GIC irqchips, move IPIs to handle_percpu_devid_irq() as
handle_percpu_devid_fasteoi_ipi() isn't actually required.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201109094121.29975-4-valentin.schneider@arm.com
As done for the Arm GIC irqchips, move IPIs to handle_percpu_devid_irq() as
handle_percpu_devid_fasteoi_ipi() isn't actually required.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201109094121.29975-3-valentin.schneider@arm.com
handle_percpu_devid_fasteoi_ipi() states:
* The biggest difference with the IRQ version is that the interrupt is
* EOIed early, as the IPI could result in a context switch, and we need to
* make sure the IPI can fire again
All that can actually happen scheduler-wise within the handling of an IPI
is the raising of TIF_NEED_RESCHED (and / or folding thereof into
preempt_count); see scheduler_ipi() or sched_ttwu_pending() for instance.
Said flag / preempt_count is evaluated some time later before returning to
whatever context was interrupted, and this gates a call to
preempt_schedule_irq() (arm64_preempt_schedule_irq() in arm64).
Per the above, SGI's do not need a different handler than PPI's, so make
them use the same (handle_percpu_devid_irq).
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201109094121.29975-2-valentin.schneider@arm.com
This patch extends irqchip driver for ocelot to be used with an other
vcoreiii base platform: Jaguar2.
Based on a larger patch from Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201125103206.136498-7-gregory.clement@bootlin.com
This patch extends irqchip driver for ocelot to be used with an other
vcoreiii base platform: Serval.
Based on a larger patch from Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201125103206.136498-6-gregory.clement@bootlin.com
This patch extends irqchip driver for oceleot to be used with an other
vcoreiii base platform: Luton.
For this platform there is a few differences:
- the interrupt must be enabled for the parent controller
- there is no trigger register needed to be managed
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201125103206.136498-5-gregory.clement@bootlin.com
This patch extends irqchip driver for oceleot to be used with other
vcoreiii base platforms.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201125103206.136498-4-gregory.clement@bootlin.com
The 10us delay of the poll on the GICR_VPENDBASER.Dirty bit is too
high, which might greatly affect the total scheduling latency of a
vCPU in our measurement. So we reduce it to 1 to lessen the impact.
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201128141857.983-2-lushenming@huawei.com
The alpine-msi driver has an interesting allocation error handling,
where it frees the same interrupts repeatedly. Hilarity follows.
This code is probably never executed, but let's fix it nonetheless.
Fixes: e6b78f2c3e ("irqchip: Add the Alpine MSIX interrupt controller")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Cc: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Cc: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20201129135525.396671-1-maz@kernel.org
Add an new IRQ chip declaration for LS1043A and LS1088A, and cleanup
the use of the "bit_reverse" property, now gated on the Soc type.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201130101515.27431-1-biwen.li@oss.nxp.com
Fix build warnings as below:
drivers/irqchip/irq-loongson-htpic.c: In function 'htpic_reg_init':
>> drivers/irqchip/irq-loongson-htpic.c:62:12: warning: variable 'val' set but not used [-Wunused-but-set-variable]
62 | uint32_t val;
| ^~~
drivers/irqchip/irq-loongson-htpic.c: At top level:
>> drivers/irqchip/irq-loongson-htpic.c:84:12: warning: no previous prototype for 'htpic_of_init' [-Wmissing-prototypes]
84 | int __init htpic_of_init(struct device_node *node, struct device_node *parent)
| ^~~~~~~~~~~~~
Fixes: a93f1d903f ("irqchip: Add driver for Loongson-3 HyperTransport PIC controller")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1607159744-995-1-git-send-email-chenhuacai@kernel.org
In order to reduce the impact of the VPT parsing happening on the GIC,
we can split the vcpu reseidency in two phases:
- programming GICR_VPENDBASER: this still happens in vcpu_load()
- checking for the VPT parsing to be complete: this can happen
on vcpu entry (in kvm_vgic_flush_hwstate())
This allows the GIC and the CPU to work in parallel, rewmoving some
of the entry overhead.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201128141857.983-3-lushenming@huawei.com
- Fix Exiu driver trigger type when using ACPI
- Fix GICv3 ITS suspend/resume to use the in-kernel path
at all times, sidestepping braindead firmware support
-----BEGIN PGP SIGNATURE-----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=IjDX
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Fix Exiu driver trigger type when using ACPI
- Fix GICv3 ITS suspend/resume to use the in-kernel path
at all times, sidestepping braindead firmware support
Link: https://lore.kernel.org/r/20201122184752.553990-1-maz@kernel.org
On systems without HW-based collections (i.e. anything except GIC-500),
we rely on firmware to perform the ITS save/restore. This doesn't
really work, as although FW can properly save everything, it cannot
fully restore the state of the command queue (the read-side is reset
to the head of the queue). This results in the ITS consuming previously
processed commands, potentially corrupting the state.
Instead, let's always save the ITS state on suspend, disabling it in the
process, and restore the full state on resume. This saves us from broken
FW as long as it doesn't enable the ITS by itself (for which we can't do
anything).
This amounts to simply dropping the ITS_FLAGS_SAVE_SUSPEND_STATE.
Signed-off-by: Xu Qiang <xuqiang36@huawei.com>
[maz: added warning on resume, rewrote commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201107104226.14282-1-xuqiang36@huawei.com
Since fwspec->param_count of ACPI node is two, the index of IRQ type
in fwspec->param[] should be 1 rather than 2.
Fixes: 3d090a36c8 ("irqchip/exiu: Implement ACPI support")
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20201117032015.11805-1-cbz@baozis.org
Cc: stable@vger.kernel.org
- Fix the fallout of the IPI as interrupt conversion in Kconfig and the
BCM2836 interrupt chip driver/
- Fixes for interrupt affinity setting and the handling of hierarchical
irq domains in the SiFive PLIC driver.
- Make the unmapped event handling in the TI SCI driver work correctly.
- A few minor fixes and cleanups in various chip drivers and Kconfig.
-----BEGIN PGP SIGNATURE-----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=HUPi
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for interrupt chip drivers:
- Fix the fallout of the IPI as interrupt conversion in Kconfig and
the BCM2836 interrupt chip driver
- Fixes for interrupt affinity setting and the handling of
hierarchical irq domains in the SiFive PLIC driver
- Make the unmapped event handling in the TI SCI driver work
correctly
- A few minor fixes and cleanups in various chip drivers and Kconfig"
* tag 'irq-urgent-2020-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: irqchip: ti, sci-inta: Fix diagram indentation for unmapped events
irqchip/ti-sci-inta: Add support for unmapped event handling
dt-bindings: irqchip: ti, sci-inta: Update for unmapped event handling
irqchip/renesas-intc-irqpin: Merge irlm_bit and needs_irlm
irqchip/sifive-plic: Fix chip_data access within a hierarchy
irqchip/sifive-plic: Fix broken irq_set_affinity() callback
irqchip/stm32-exti: Add all LP timer exti direct events support
irqchip/bcm2836: Fix missing __init annotation
irqchip/mips: Drop selection of IRQ_DOMAIN_HIERARCHY
irqchip/mst: Make mst_intc_of_init static
irqchip/mst: MST_IRQ should depend on ARCH_MEDIATEK or ARCH_MSTARV7
genirq: Let GENERIC_IRQ_IPI select IRQ_DOMAIN_HIERARCHY
The DMA (BCDMA/PKTDMA and their rings/flows) events are under the INTA's
supervision as unmapped events in AM64.
In order to keep the current SW stack working, the INTA driver must replace
the dev_id with it's own when a request comes for BCDMA or PKTDMA
resources.
Implement parsing of the optional "ti,unmapped-event-sources" phandle array
to get the sci-dev-ids of the devices where the unmapped events originate.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201020073243.19255-3-peter.ujfalusi@ti.com
Get rid of the separate flag to indicate if the IRLM bit is present in
the INTC/Interrupt Control Register 0, by considering -1 an invalid
irlm_bit value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201028153955.1736767-1-geert+renesas@glider.be
The plic driver crashes in plic_irq_unmask() when the interrupt is within a
hierarchy, as it picks the top-level chip_data instead of its local one.
Using irq_data_get_irq_chip_data() instead of irq_get_chip_data() solves
the issue for good.
Fixes: f1ad1133b1 ("irqchip/sifive-plic: Add support for multiple PLICs")
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
[maz: rewrote commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Link: https://lore.kernel.org/r/20201029023738.127472-1-greentime.hu@sifive.com
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An interrupt submitted to an affinity change will always be left enabled
after plic_set_affinity() has been called, while the expectation is that
it should stay in whatever state it was before the call.
Preserving the configuration fixes a PWM hang issue on the Unleashed
board.
[ 919.015783] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[ 919.020922] rcu: 0-...0: (0 ticks this GP)
idle=7d2/1/0x4000000000000002 softirq=1424/1424 fqs=105807
[ 919.030295] (detected by 1, t=225825 jiffies, g=1561, q=3496)
[ 919.036109] Task dump for CPU 0:
[ 919.039321] kworker/0:1 R running task 0 30 2 0x00000008
[ 919.046359] Workqueue: events set_brightness_delayed
[ 919.051302] Call Trace:
[ 919.053738] [<ffffffe000930d92>] __schedule+0x194/0x4de
[ 982.035783] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[ 982.040923] rcu: 0-...0: (0 ticks this GP)
idle=7d2/1/0x4000000000000002 softirq=1424/1424 fqs=113325
[ 982.050294] (detected by 1, t=241580 jiffies, g=1561, q=3509)
[ 982.056108] Task dump for CPU 0:
[ 982.059321] kworker/0:1 R running task 0 30 2 0x00000008
[ 982.066359] Workqueue: events set_brightness_delayed
[ 982.071302] Call Trace:
[ 982.073739] [<ffffffe000930d92>] __schedule+0x194/0x4de
[..]
Fixes: bb0fed1c60 ("irqchip/sifive-plic: Switch to fasteoi flow")
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
[maz: tidy-up commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20201020081532.2377-1-greentime.hu@sifive.com
bcm2836_arm_irqchip_smp_init() calls set_smp_ipi_range(), which has
an __init annotation. Make sure the caller has the same annotation.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl+TT4gPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx322MP/1mI56SyOFx30AqtWBPSjHJp+DzhOObyb4vD
ndYuicBIn9tJwvVRBBZkfsbIU8EENVwrN3hOpesaj9L7xiqOqKakcnyC1REYmpIs
8XBDfdZzy5PrMHIu3fF1ZDCQyO7KndGf5DfLVxJtcf1tSPQyQCuIA3FtS6d8Bxnz
r491+om67ucnlFD5X0Spm3RdZH+ECmXx2iXwoS0Zi7P+X+S+ovG8wBV/X0ggeoBc
Zgi4W01SiRupmSVZ6PA7FvWaLGQErQAALQOcFtMcFgjeWzc1v2QzcURELH8JW7ro
72AH9st1Kvi3hoN2HNNzUnNUdQvZ+AdH8skMIpN/e1cBYqYStAF3gm/R9h+iVHbG
GMmgzXHAFErfAW2UcF8tq1CzvQ5ChcTLNXdeoa8CeQbcDfocF3EyuKSPuDH+ve0H
kk4tPesTAc6XCEVwLaGnoC75sdum5mSi8h9vqhln2KCdeTY7jxzH9YGHjm71Supb
kV9vqo5Q5U/c5l2nU4r5q/DZdIahKsk3HIQZ0iG7BifAzamaTh4uyLVjtM6HSwNz
tdHZaxoHd/PLI5IoeggFelx6qgvK5qVRLP0evgOdTLRFLj/ZbrOf0Q7DjdTy2BjZ
Lgq461QqNapOzxq43G2IDT2+P62Q1+d+YLCKBgaGQaJicyU5m9STCNo3UBb1qH1h
W6UwGF5z
=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
Now that GENERIC_IRQ_IPI selects IRQ_DOMAIN_HIERARCHY, there is no
need to have this conditional select for IRQ_MIPS_CPU. Similarily,
MIPS_GIC only needs selecting GENERIC_IRQ_IPI.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
mst_intc_of_init has no external caller, so let's make it static.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The MStar interrupt controller is only found on MStar, SigmaStar, and
Mediatek SoCs. Hence add dependencies on ARCH_MEDIATEK and
ARCH_MSTARV7, to prevent asking the user about the MStar interrupt
controller driver when configuring a kernel without support for MStar,
SigmaStar, and Mediatek SoCs.
Fixes: ad4c938c92 ("irqchip/irq-mst: Add MStar interrupt controller support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Daniel Palmer <daniel@thingy.jp>
Link: https://lore.kernel.org/r/20201014131703.18021-1-geert+renesas@glider.be
- Add support for generic initiator-only proximity domains to
the ACPI NUMA code and the architectures using it (Jonathan
Cameron).
- Clean up some non-ACPICA code referring to debug facilities from
ACPICA that are not actually used in there (Hanjun Guo).
- Add new DPTF driver for the PCH FIVR participant (Srinivas
Pandruvada).
- Reduce overhead related to accessing GPE registers in ACPICA and
the OS interface layer and make it possible to access GPE registers
using logical addresses if they are memory-mapped (Rafael Wysocki).
- Update the ACPICA code in the kernel to upstream revision 20200925
including changes as follows:
* Add predefined names from the SMBus sepcification (Bob Moore).
* Update acpi_help UUID list (Bob Moore).
* Return exceptions for string-to-integer conversions in iASL (Bob
Moore).
* Add a new "ALL <NameSeg>" debugger command (Bob Moore).
* Add support for 64 bit risc-v compilation (Colin Ian King).
* Do assorted cleanups (Bob Moore, Colin Ian King, Randy Dunlap).
- Add new ACPI backlight whitelist entry for HP 635 Notebook (Alex
Hung).
- Move TPS68470 OpRegion driver to drivers/acpi/pmic/ and split out
Kconfig and Makefile specific for ACPI PMIC (Andy Shevchenko).
- Clean up the ACPI SoC driver for AMD SoCs (Hanjun Guo).
- Add missing config_item_put() to fix refcount leak (Hanjun Guo).
- Drop lefrover field from struct acpi_memory_device (Hanjun Guo).
- Make the ACPI extlog driver check for RDMSR failures (Ben
Hutchings).
- Fix handling of lid state changes in the ACPI button driver when
input device is closed (Dmitry Torokhov).
- Fix several assorted build issues (Barnabás Pőcze, John Garry,
Nathan Chancellor, Tian Tao).
- Drop unused inline functions and reduce code duplication by using
kobj_to_dev() in the NFIT parsing code (YueHaibing, Wang Qing).
- Serialize tools/power/acpi Makefile (Thomas Renninger).
-----BEGIN PGP SIGNATURE-----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=feLU
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These add support for generic initiator-only proximity domains to the
ACPI NUMA code and the architectures using it, clean up some
non-ACPICA code referring to debug facilities from ACPICA, reduce the
overhead related to accessing GPE registers, add a new DPTF (Dynamic
Power and Thermal Framework) participant driver, update the ACPICA
code in the kernel to upstream revision 20200925, add a new ACPI
backlight whitelist entry, fix a few assorted issues and clean up some
code.
Specifics:
- Add support for generic initiator-only proximity domains to the
ACPI NUMA code and the architectures using it (Jonathan Cameron)
- Clean up some non-ACPICA code referring to debug facilities from
ACPICA that are not actually used in there (Hanjun Guo)
- Add new DPTF driver for the PCH FIVR participant (Srinivas
Pandruvada)
- Reduce overhead related to accessing GPE registers in ACPICA and
the OS interface layer and make it possible to access GPE registers
using logical addresses if they are memory-mapped (Rafael Wysocki)
- Update the ACPICA code in the kernel to upstream revision 20200925
including changes as follows:
+ Add predefined names from the SMBus sepcification (Bob Moore)
+ Update acpi_help UUID list (Bob Moore)
+ Return exceptions for string-to-integer conversions in iASL (Bob
Moore)
+ Add a new "ALL <NameSeg>" debugger command (Bob Moore)
+ Add support for 64 bit risc-v compilation (Colin Ian King)
+ Do assorted cleanups (Bob Moore, Colin Ian King, Randy Dunlap)
- Add new ACPI backlight whitelist entry for HP 635 Notebook (Alex
Hung)
- Move TPS68470 OpRegion driver to drivers/acpi/pmic/ and split out
Kconfig and Makefile specific for ACPI PMIC (Andy Shevchenko)
- Clean up the ACPI SoC driver for AMD SoCs (Hanjun Guo)
- Add missing config_item_put() to fix refcount leak (Hanjun Guo)
- Drop lefrover field from struct acpi_memory_device (Hanjun Guo)
- Make the ACPI extlog driver check for RDMSR failures (Ben
Hutchings)
- Fix handling of lid state changes in the ACPI button driver when
input device is closed (Dmitry Torokhov)
- Fix several assorted build issues (Barnabás Pőcze, John Garry,
Nathan Chancellor, Tian Tao)
- Drop unused inline functions and reduce code duplication by using
kobj_to_dev() in the NFIT parsing code (YueHaibing, Wang Qing)
- Serialize tools/power/acpi Makefile (Thomas Renninger)"
* tag 'acpi-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
ACPICA: Update version to 20200925 Version 20200925
ACPICA: Remove unnecessary semicolon
ACPICA: Debugger: Add a new command: "ALL <NameSeg>"
ACPICA: iASL: Return exceptions for string-to-integer conversions
ACPICA: acpi_help: Update UUID list
ACPICA: Add predefined names found in the SMBus sepcification
ACPICA: Tree-wide: fix various typos and spelling mistakes
ACPICA: Drop the repeated word "an" in a comment
ACPICA: Add support for 64 bit risc-v compilation
ACPI: button: fix handling lid state changes when input device closed
tools/power/acpi: Serialize Makefile
ACPI: scan: Replace ACPI_DEBUG_PRINT() with pr_debug()
ACPI: memhotplug: Remove 'state' from struct acpi_memory_device
ACPI / extlog: Check for RDMSR failure
ACPI: Make acpi_evaluate_dsm() prototype consistent
docs: mm: numaperf.rst Add brief description for access class 1.
node: Add access1 class to represent CPU to memory characteristics
ACPI: HMAT: Fix handling of changes from ACPI 6.2 to ACPI 6.3
ACPI: Let ACPI know we support Generic Initiator Affinity Structures
x86: Support Generic Initiator only proximity domains
...
Iteration over memblock.reserved with for_each_reserved_mem_region() used
__next_reserved_mem_region() that implemented a subset of
__next_mem_region().
Use __for_each_mem_range() and, essentially, __next_mem_region() with
appropriate parameters to reduce code duplication.
While on it, rename for_each_reserved_mem_region() to
for_each_reserved_mem_range() for consistency.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> [.clang-format]
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Emil Renner Berthing <kernel@esmil.dk>
Cc: Hari Bathini <hbathini@linux.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: https://lkml.kernel.org/r/20200818151634.14343-17-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kexec can directly boot into a new kernel without going to complete
reboot. This can leave the previous kernel's configuration for PDC
interrupts as is.
Clear previous kernel's configuration during init by setting interrupts
in enable bank to zero. The IRQs specified in qcom,pdc-ranges property
are the only ones that can be used by the new kernel so clear only those
IRQs. The remaining ones may be in use by a different kernel and should
not be set by new kernel.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-7-git-send-email-mkshah@codeaurora.org
Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag to enable/unmask the
wakeirqs during suspend entry.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-6-git-send-email-mkshah@codeaurora.org
This interrupt controller is found in the Actions Semi Owl SoCs (S500,
S700 and S900) and provides support for handling up to 3 external
interrupt lines.
Each line can be independently configured as interrupt and triggers on
either of the edges or either of the levels. Additionally, each line
can also be masked individually.
Co-developed-by: Parthiban Nallathambi <pn@denx.de>
Co-developed-by: Saravanan Sekar <sravanhome@gmail.com>
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1a010ef0eb78831b5657d74a0fcdef7a8efb2ec4.1600114378.git.cristian.ciocaltea@gmail.com
Add support to use dw-apb-ictl as primary interrupt controller.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
[maz: minor fixups]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Haoyu Lv <lvhaoyu@huawei.com>
Link: https://lore.kernel.org/r/20200924071754.4509-4-thunder.leizhen@huawei.com
Add the required abstractions that will help introducing hierarchical
domain support to the dw-apb-ictl driver.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
[maz: commit message, some cleanups]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Haoyu Lv <lvhaoyu@huawei.com>
Link: https://lore.kernel.org/r/20200924071754.4509-3-thunder.leizhen@huawei.com
Note this crash is present before any of the patches in this series, but
as explained below it is highly unlikely anyone is shipping a firmware that
causes it. Tests were done using an overriden SRAT.
On ARM64, the gic-v3 driver directly parses SRAT to locate GIC Interrupt
Translation Service (ITS) Affinity Structures. This is done much later
in the boot than the parses of SRAT which identify proximity domains.
As a result, an ITS placed in a proximity domain that is not defined by
another SRAT structure will result in a NUMA node that is not completely
configured and a crash.
ITS [mem 0x202100000-0x20211ffff]
ITS@0x0000000202100000: Using ITS number 0
Unable to handle kernel paging request at virtual address 0000000000001a08
...
Call trace:
__alloc_pages_nodemask+0xe8/0x338
alloc_pages_node.constprop.0+0x34/0x40
its_probe_one+0x2f8/0xb18
gic_acpi_parse_madt_its+0x108/0x150
acpi_table_parse_entries_array+0x17c/0x264
acpi_table_parse_entries+0x48/0x6c
acpi_table_parse_madt+0x30/0x3c
its_init+0x1c4/0x644
gic_init_bases+0x4b8/0x4ec
gic_acpi_init+0x134/0x264
acpi_match_madt+0x4c/0x84
acpi_table_parse_entries_array+0x17c/0x264
acpi_table_parse_entries+0x48/0x6c
acpi_table_parse_madt+0x30/0x3c
__acpi_probe_device_table+0x8c/0xe8
irqchip_init+0x3c/0x48
init_IRQ+0xcc/0x100
start_kernel+0x33c/0x548
ACPI 6.3 allows any set of Affinity Structures in SRAT to define a proximity
domain. However, as we do not see this crash, we can conclude that no
firmware is currently placing an ITS in a node that is separate from
those containing memory and / or processors.
We could modify the SRAT parsing behavior to identify the existence
of Proximity Domains unique to the ITS structures, and handle them as
a special case of a generic initiator (once support for those merges).
This patch avoids the complexity that would be needed to handle this corner
case, by not allowing the ITS entry parsing code to instantiate new NUMA
Nodes. If one is encountered that does not already exist, then NO_NUMA_NODE
is assigned and a warning printed just as if the value had been greater than
allowed NUMA Nodes.
"SRAT: Invalid NUMA node -1 in ITS affinity"
Whilst this does not provide the full flexibility allowed by ACPI,
it does fix the problem. We can revisit a more sophisticated solution if
needed by future platforms.
Change is simply to replace acpi_map_pxm_to_node with pxm_to_node reflecting
the fact a new mapping is not created.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce a static key identifying Samsung's unique creation, allowing
to replace the indirect call to compute the base addresses with
a simple test on the static key.
Faster, cheaper, negative diffstat.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Although it doesn't seem possible to disable individual mailbox
interrupts, we still need to provide some callbacks.
Fixes: 09eb672ce4fb ("irqchip/bcm2836: Configure mailbox interrupts as standard interrupts")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
To introduce IPIs as standard interrupts to the Armada 370-XP
driver, let's allocate a completely separate irqdomain and
irqchip combo that lives parallel to the "standard" one.
This effectively should be modelled as a chained interrupt
controller, but the code is in such a state that it is
pretty hard to shoehorn, as it would require the rewrite
of the MSI layer as well.
Signed-off-by: Marc Zyngier <maz@kernel.org>
In order to switch the hip04 driver to provide standard interrupts
for IPIs, rework the way interrupts are allocated, making sure
the irqdomain covers the SGIs as well as the rest of the interrupt
range.
The driver is otherwise so old-school that it creates all interrupts
upfront (duh!), so there is hardly anything else to change, apart
from communicating the IPIs to the arch code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
In order to switch the bcm2836 driver to privide standard interrupts
for IPIs, it first needs to stop lying about the way things work.
The mailbox interrupt is actually a multiplexer, with enough
bits to store 32 pending interrupts per CPU. So let's turn it
into a chained irqchip.
Once this is done, we can instanciate the corresponding IPIs,
and pass them to the architecture code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The architecture code now enables the IPIs as required, so no
need to enable SGIs by default in the GIC code.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Change the way we deal with GIC SGIs by turning them into proper
IRQs, and calling into the arch code to register the interrupt range
instead of a callback.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
As we are about to change quite a lot of the SMP support code,
let's start by moving it around so that it minimizes the amount
of #ifdefery.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Change the way we deal with GICv3 SGIs by turning them into proper
IRQs, and calling into the arch code to register the interrupt range
instead of a callback.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add support for the interrupt controller inside the sl28 CPLD management
controller.
The interrupt controller can handle at most 8 interrupts and is really
simplistic and consists only of an interrupt mask and an interrupt
pending register.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The K3 AM65x and J721E SoCs have the next generation of the PRU-ICSS IP,
commonly called ICSSG. The PRUSS INTC present within the ICSSG supports
more System Events (160 vs 64), more Interrupt Channels and Host Interrupts
(20 vs 10) compared to the previous generation PRUSS INTC instances. The
first 2 and the last 10 of these host interrupt lines are used by the
PRU and other auxiliary cores and sub-modules within the ICSSG, with 8
host interrupts connected to MPU. The host interrupts 5, 6, 7 are also
connected to the other ICSSG instances within the SoC and can be
partitioned as per system integration through the board dts files.
Enhance the PRUSS INTC driver to add support for this ICSSG INTC
instance.
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
This implements the irq_get_irqchip_state and irq_set_irqchip_state
callbacks for the TI PRUSS INTC driver. The set callback can be used
by drivers to "kick" a PRU by injecting a PRU system event.
Co-developed-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The PRUSS INTC has a fixed number of output interrupt lines that are
connected to a number of processors or other PRUSS instances or other
devices (like DMA) on the SoC. The output interrupt lines 2 through 9
are usually connected to the main Arm host processor and are referred
to as host interrupts 0 through 7 from ARM/MPU perspective.
All of these 8 host interrupts are not always exclusively connected
to the Arm interrupt controller. Some SoCs have some interrupt lines
not connected to the Arm interrupt controller at all, while a few others
have the interrupt lines connected to multiple processors in which they
need to be partitioned as per SoC integration needs. For example, AM437x
and 66AK2G SoCs have 2 PRUSS instances each and have the host interrupt 5
connected to the other PRUSS, while AM335x has host interrupt 0 shared
between MPU and TSC_ADC and host interrupts 6 & 7 shared between MPU and
a DMA controller.
Add logic to the PRUSS INTC driver to ignore both these shared and
invalid interrupts.
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The Programmable Real-Time Unit Subsystem (PRUSS) contains a local
interrupt controller (INTC) that can handle various system input events
and post interrupts back to the device-level initiators. The INTC can
support upto 64 input events with individual control configuration and
hardware prioritization. These events are mapped onto 10 output interrupt
lines through two levels of many-to-one mapping support. Different
interrupt lines are routed to the individual PRU cores or to the host
CPU, or to other devices on the SoC. Some of these events are sourced
from peripherals or other sub-modules within that PRUSS, while a few
others are sourced from SoC-level peripherals/devices.
The PRUSS INTC platform driver manages this PRUSS interrupt controller
and implements an irqchip driver to provide a Linux standard way for
the PRU client users to enable/disable/ack/re-trigger a PRUSS system
event. The system events to interrupt channels and output interrupts
relies on the mapping configuration provided either through the PRU
firmware blob (for interrupts routed to PRU cores) or via the PRU
application's device tree node (for interrupt routed to the main CPU).
In the first case the mappings will be programmed on PRU remoteproc
driver demand (via irq_create_fwspec_mapping) during the boot of a PRU
core and cleaned up after the PRU core is stopped.
Reference counting is used to allow multiple system events to share a
single channel and to allow multiple channels to share a single host
event.
The PRUSS INTC module is reference counted during the interrupt
setup phase through the irqchip's irq_request_resources() and
irq_release_resources() ops. This restricts the module from being
removed as long as there are active interrupt users.
The driver currently supports and can be built for OMAP architecture
based AM335x, AM437x and AM57xx SoCs; Keystone2 architecture based
66AK2G SoCs and Davinci architecture based OMAP-L13x/AM18x/DA850 SoCs.
All of these SoCs support 64 system events, 10 interrupt channels and
10 output interrupt lines per PRUSS INTC with a few SoC integration
differences.
NOTE:
Each PRU-ICSS's INTC on AM57xx SoCs is preceded by a Crossbar that
enables multiple external events to be routed to a specific number
of input interrupt events. Any non-default external interrupt event
directed towards PRUSS needs this crossbar to be setup properly.
Co-developed-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Andrew F. Davis <afd@ti.com>
Co-developed-by: Roger Quadros <rogerq@ti.com>
Co-developed-by: David Lechner <david@lechnology.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
irq-renesas-irqc driver is also used on Renesas RZ/G{1,2} SoC's, update
the same to reflect the description for RENESAS_IRQC config.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200911100439.19878-1-prabhakar.mahadev-lad.rj@bp.renesas.com
The GIC's internal view of the priority mask register and the assigned
interrupt priorities are based on whether GIC security is enabled and
whether firmware routes Group 0 interrupts to EL3. At the moment, we
support priority masking when ICC_PMR_EL1 and interrupt priorities are
either both modified by the GIC, or both left unchanged.
Trusted Firmware-A's default interrupt routing model allows Group 0
interrupts to be delivered to the non-secure world (SCR_EL3.FIQ == 0).
Unfortunately, this is precisely the case that the GIC driver doesn't
support: ICC_PMR_EL1 remains unchanged, but the GIC's view of interrupt
priorities is different from the software programmed values.
Support pseudo-NMIs when SCR_EL3.FIQ == 0 by using a different value to
mask regular interrupts. All the other values remain the same.
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200912153707.667731-3-alexandru.elisei@arm.com
When NMIs cannot be enabled, the driver prints a message stating that
unambiguously. When they are enabled, the only feedback we get is a message
regarding the use of synchronization for ICC_PMR_EL1 writes, which is not
as useful for a user who is not intimately familiar with how NMIs are
implemented.
Let's make it obvious that pseudo-NMIs are enabled. Keep the message about
using a barrier for ICC_PMR_EL1 writes, because it has a non-negligible
impact on performance.
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200912153707.667731-2-alexandru.elisei@arm.com
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
There is also no need to assign NULL to 'intr->sci' as it is part of
devm-allocated memory.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200902174615.24695-1-krzk@kernel.org
As we are about to start making use of SGIs in a more conventional
way, let's describe it is the GICv3 list of interrupt types.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
In htvec_reset() only the first group of initial interrupts is cleared.
This sometimes causes spurious interrupts, so let's clear all groups.
While at it, fix the nearby comment that to match the reality of what
the driver does.
Fixes: 818e915fba ("irqchip: Add Loongson HyperTransport Vector support")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1599819978-13999-2-git-send-email-chenhc@lemote.com
ti_sci_intr_xlate_irq() return -ENOENT on fail, p_hwirq
should be int type.
Fixes: a5b659bd4b ("irqchip/ti-sci-intr: Add support for INTR being a parent to INTR")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200826035321.18620-1-yuehaibing@huawei.com
ti_sci_inta_xlate_irq() return -ENOENT on fail, p_hwirq
should be int type.
Fixes: 5c4b585d29 ("irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200826035430.21060-1-yuehaibing@huawei.com
The GIC irqchips can now use a HW resend when a retrigger is invoked by
check_irq_resend(). However, should the HW resend fail, check_irq_resend()
will still attempt to trigger a SW resend, which is still a bad idea for
the GICs.
Prevent this from happening by setting IRQD_HANDLE_ENFORCE_IRQCTX on all
GIC IRQs. Technically per-cpu IRQs do not need this, as their flow handlers
never set IRQS_PENDING, but this aligns all IRQs wrt context enforcement:
this also forces all GIC IRQ handling to happen in IRQ context (as defined
by in_irq()).
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200730170321.31228-3-valentin.schneider@arm.com
It is pretty easy to provide a retrigger callback for the ITS,
as it we already have the required support in terms of
irq_set_irqchip_state().
Note that this only works for device-generated LPIs, and not
the GICv4 doorbells, which should never have to be retriggered
anyway.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
While digging around IRQCHIP_EOI_IF_HANDLED and irq/resend.c, it has come
to my attention that the IRQ resend situation seems a bit precarious for
the GIC(s).
When marking an IRQ with IRQS_PENDING, handle_fasteoi_irq() will bail out
and issue an irq_eoi(). Should the IRQ in question be re-enabled,
check_irq_resend() will trigger a SW resend, which will go through the flow
handler again and issue *another* irq_eoi() on the *same* IRQ
activation. This is something the GIC spec clearly describes as a bad idea:
any EOI must match a previous ACK.
Implement irq_chip.irq_retrigger() for the GIC chips by setting the GIC
pending bit of the relevant IRQ. After being called by check_irq_resend(),
this will eventually trigger a *new* interrupt which we will handle as usual.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200730170321.31228-2-valentin.schneider@arm.com
- Revert the platform driver conversion of interrupt chip drivers as it
turned out to create more problems than it solves.
- Fix a trivial typo in the new module helpers which made probing reliably
fail.
- Small fixes in the STM32 and MIPS Ingenic drivers
- The TI firmware rework which had badly managed dependencies and had to
wait post rc1.
-----BEGIN PGP SIGNATURE-----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=guRc
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for interrupt chip drivers:
- Revert the platform driver conversion of interrupt chip drivers as
it turned out to create more problems than it solves.
- Fix a trivial typo in the new module helpers which made probing
reliably fail.
- Small fixes in the STM32 and MIPS Ingenic drivers
- The TI firmware rework which had badly managed dependencies and had
to wait post rc1"
* tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/ingenic: Leave parent IRQ unmasked on suspend
irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake
irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER helperse
irqchip: Fix probing deferal when using IRQCHIP_PLATFORM_DRIVER helpers
arm64: dts: k3-am65: Update the RM resource types
arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings
arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings
irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC
irqchip/ti-sci-inta: Do not store TISCI device id in platform device id field
dt-bindings: irqchip: Convert ti, sci-inta bindings to yaml
dt-bindings: irqchip: ti, sci-inta: Update docs to support different parent.
irqchip/ti-sci-intr: Add support for INTR being a parent to INTR
dt-bindings: irqchip: Convert ti, sci-intr bindings to yaml
dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent
firmware: ti_sci: Add support for getting resource with subtype
firmware: ti_sci: Drop unused structure ti_sci_rm_type_map
firmware: ti_sci: Drop the device id to resource type translation
All the wakeup sources we possibly want will go through the interrupt
controller, so the parent IRQ must not be masked during suspend, or
there won't be any way to wake up the system.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200819180602.136969-1-paul@crapouillou.net
In the current code, when the eoi callback of the exti clears the pending
bit of the current interrupt, it will first read the values of fpr and
rpr, then logically OR the corresponding bit of the interrupt number,
and finally write back to fpr and rpr.
We found through experiments that if two exti interrupts,
we call them int1/int2, arrive almost at the same time. in our scenario,
the time difference is 30 microseconds, assuming int1 is triggered first.
there will be an extreme scenario: both int's pending bit are set to 1,
the irq handle of int1 is executed first, and eoi handle is then executed,
at this moment, all pending bits are cleared, but the int 2 has not
finally been reported to the cpu yet, which eventually lost int2.
According to stm32's TRM description about rpr and fpr: Writing a 1 to this
bit will trigger a rising edge event on event x, Writing 0 has no
effect.
Therefore, when clearing the pending bit, we only need to clear the
pending bit of the irq.
Fixes: 927abfc446 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # v4.18+
Link: https://lore.kernel.org/r/20200820031629.15582-1-qiuguorui1@huawei.com
It has become obvious that switching a number of irqchip drivers
to being platform drivers without considering the platform was a
mistake. We have multiple reports of end-point drivers not
probing because the irqchip driver isn't there yet, breaking
the expectations of the users.
This patch reverts:
920ecb8c35 ("irqchip/mtk-cirq: Convert to a platform driver")
f97dbf48ca ("irqchip/mtk-sysirq: Convert to a platform driver")
5be57099d4 ("irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros")
95bf9305d2 ("irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module")
and leave QCOM PDC, MTK sysrq and cirq drivers as built-in, special purpose
drivers for the time being until we have worked out a better solution.
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reported-by: Frank Wunderlich <linux@fw-web.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/93debe6a0308b66d3f307af67ba7ec2c@kernel.org
It was a good idea to move it out at first, but the irqchip code
is still tightly connected to the s3c24xx platform code and uses
multiple internal header files, so just move it back for the
time being to avoid those dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-21-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When probing an interrupt controller that is behind a parent,
we try to check whether the parent domain is available as
an indication that we can actually try to probe.
Unfortunately, we are checking this with the firmware node of
the about to be probed device, not the parent. This is obviously
bound to fail.
Instead, use the parent node.
Fixes: f8410e6265 ("irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Driver assumes that Interrupt parent to Interrupt Aggregator is always
Interrupt router. This is not true always and GIC can be a parent to
Interrupt Aggregator. Update the driver to detect the parent and request
the parent irqs accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806074826.24607-11-lokeshvutla@ti.com
Even though DT doesn't make active use of id field in platform_device, we cannot
hijack it to store TISCI device id. So create a field in struct ti_sci_inta
for storing TISCI id and drop usage of id field in platform_device.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806074826.24607-10-lokeshvutla@ti.com
Driver assumes that Interrupt parent to Interrupt router is always GIC.
This is not true always and an Interrupt Router can be a parent to
Interrupt Router. Update the driver to detect the parent and request the
parent irqs accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200806074826.24607-7-lokeshvutla@ti.com
- Infrastructure to allow building irqchip drivers as modules
- Consolidation of irqchip ACPI probing
- Removal of the EOI-preflow interrupt handler which was required for
SPARC support and became obsolete after SPARC was converted to
use sparse interrupts.
- Cleanups, fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=KA8b
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual boring updates from the interrupt subsystem:
- Infrastructure to allow building irqchip drivers as modules
- Consolidation of irqchip ACPI probing
- Removal of the EOI-preflow interrupt handler which was required for
SPARC support and became obsolete after SPARC was converted to use
sparse interrupts.
- Cleanups, fixes and improvements all over the place"
* tag 'irq-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
irqchip/loongson-pch-pic: Fix the misused irq flow handler
irqchip/loongson-htvec: Support 8 groups of HT vectors
irqchip/loongson-liointc: Fix misuse of gc->mask_cache
dt-bindings: interrupt-controller: Update Loongson HTVEC description
irqchip/imx-intmux: Fix irqdata regs save in imx_intmux_runtime_suspend()
irqchip/imx-intmux: Implement intmux runtime power management
irqchip/gic-v4.1: Use GFP_ATOMIC flag in allocate_vpe_l1_table()
irqchip: Fix IRQCHIP_PLATFORM_DRIVER_* compilation by including module.h
irqchip/stm32-exti: Map direct event to irq parent
irqchip/mtk-cirq: Convert to a platform driver
irqchip/mtk-sysirq: Convert to a platform driver
irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros
irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros
irqchip: irq-bcm2836.h: drop a duplicated word
irqchip/gic-v4.1: Ensure accessing the correct RD when writing INVALLR
irqchip/irq-bcm7038-l1: Guard uses of cpu_logical_map
irqchip/gic-v3: Remove unused register definition
irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module
genirq: Export irq_chip_retrigger_hierarchy and irq_chip_set_vcpu_affinity_parent
irqdomain: Export irq_domain_update_bus_token
...
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
that helps the debugging of IRQ affinity logic bugs, and fix a memory leak.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oKU9
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-08-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Fix a recent IRQ affinities regression, add in a missing debugfs
printout that helps the debugging of IRQ affinity logic bugs, and fix
a memory leak"
* tag 'irq-urgent-2020-08-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/debugfs: Add missing irqchip flags
genirq/affinity: Make affinity setting if activated opt-in
irqdomain/treewide: Free firmware node after domain removal
- Removal of the tremendously unpopular read_barrier_depends() barrier,
which is a NOP on all architectures apart from Alpha, in favour of
allowing architectures to override READ_ONCE() and do whatever dance
they need to do to ensure address dependencies provide LOAD ->
LOAD/STORE ordering. This work also offers a potential solution if
compilers are shown to convert LOAD -> LOAD address dependencies into
control dependencies (e.g. under LTO), as weakly ordered architectures
will effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic, augment
the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the device
ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions and
kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words.
-----BEGIN PGP SIGNATURE-----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=mh79
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 and cross-arch updates from Catalin Marinas:
"Here's a slightly wider-spread set of updates for 5.9.
Going outside the usual arch/arm64/ area is the removal of
read_barrier_depends() series from Will and the MSI/IOMMU ID
translation series from Lorenzo.
The notable arm64 updates include ARMv8.4 TLBI range operations and
translation level hint, time namespace support, and perf.
Summary:
- Removal of the tremendously unpopular read_barrier_depends()
barrier, which is a NOP on all architectures apart from Alpha, in
favour of allowing architectures to override READ_ONCE() and do
whatever dance they need to do to ensure address dependencies
provide LOAD -> LOAD/STORE ordering.
This work also offers a potential solution if compilers are shown
to convert LOAD -> LOAD address dependencies into control
dependencies (e.g. under LTO), as weakly ordered architectures will
effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at
LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic,
augment the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the
device ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions
and kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words"
Link: http://lkml.kernel.org/r/20200710165203.31284-1-will@kernel.org
Link: http://lkml.kernel.org/r/20200619082013.13661-1-lorenzo.pieralisi@arm.com
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (82 commits)
arm64: use IRQ_STACK_SIZE instead of THREAD_SIZE for irq stack
arm64/mm: save memory access in check_and_switch_context() fast switch path
arm64: sigcontext.h: delete duplicated word
arm64: ptrace.h: delete duplicated word
arm64: pgtable-hwdef.h: delete duplicated words
bus: fsl-mc: Add ACPI support for fsl-mc
bus/fsl-mc: Refactor the MSI domain creation in the DPRC driver
of/irq: Make of_msi_map_rid() PCI bus agnostic
of/irq: make of_msi_map_get_device_domain() bus agnostic
dt-bindings: arm: fsl: Add msi-map device-tree binding for fsl-mc bus
of/device: Add input id to of_dma_configure()
of/iommu: Make of_map_rid() PCI agnostic
ACPI/IORT: Add an input ID to acpi_dma_configure()
ACPI/IORT: Remove useless PCI bus walk
ACPI/IORT: Make iort_msi_map_rid() PCI agnostic
ACPI/IORT: Make iort_get_device_domain IRQ domain agnostic
ACPI/IORT: Make iort_match_node_callback walk the ACPI namespace for NC
arm64: enable time namespace support
arm64/vdso: Restrict splitting VVAR VMA
arm64/vdso: Handle faults on timens page
...
Loongson PCH PIC is a standard level triggered PIC, and it need to clear
interrupt during unmask.
Fixes: ef8c01eb64 ("irqchip: Add Loongson PCH PIC controller")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lore.kernel.org/r/1596099090-23516-6-git-send-email-chenhc@lemote.com
The original version can only used by old Loongson-3 which only use 4
groups of HT vectors. Now Loongson-3A R4 can use 8 groups, so improve
the driver to support all 8 groups.
Fixes: 818e915fba ("irqchip: Add Loongson HyperTransport Vector support")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lore.kernel.org/r/1596099090-23516-5-git-send-email-chenhc@lemote.com
In gc->mask_cache bits, 1 means enabled and 0 means disabled, but in the
loongson-liointc driver mask_cache is misused by reverting its meaning.
This patch fix the bug and update the comments as well.
Fixes: dbb1522679 ("irqchip: Add driver for Loongson I/O Local Interrupt Controller")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1596099090-23516-4-git-send-email-chenhc@lemote.com
Gcc report warning as follows:
drivers/irqchip/irq-imx-intmux.c:316:29: warning:
variable 'irqchip_data' set but not used [-Wunused-but-set-variable]
316 | struct intmux_irqchip_data irqchip_data;
| ^~~~~~~~~~~~
irqdata regs is stored to this variable on the stack in
imx_intmux_runtime_suspend(), which means a nop. this commit
fix to save regs to the right place.
Fixes: bb403111e0 ("irqchip/imx-intmux: Implement intmux runtime power management")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200729155849.33919-1-weiyongjun1@huawei.com
Add ACPI support in the fsl-mc driver. Driver parses MC DSDT table to
extract memory and other resources.
Interrupt (GIC ITS) information is extracted from the MADT table
by drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c.
IORT table is parsed to configure DMA.
Signed-off-by: Makarand Pawagi <makarand.pawagi@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20200619082013.13661-13-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The DPRC driver is not taking into account the msi-map property
and assumes that the icid is the same as the stream ID. Although
this assumption is correct, generalize the code to include a
translation between icid and streamID.
Furthermore do not just copy the MSI domain from parent (for child
containers), but use the information provided by the msi-map property.
If the msi-map property is missing from the device tree retain the old
behaviour for backward compatibility ie the child DPRC objects
inherit the MSI domain from the parent.
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200619082013.13661-12-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
John reported that on a RK3288 system the perf per CPU interrupts are all
affine to CPU0 and provided the analysis:
"It looks like what happens is that because the interrupts are not per-CPU
in the hardware, armpmu_request_irq() calls irq_force_affinity() while
the interrupt is deactivated and then request_irq() with IRQF_PERCPU |
IRQF_NOBALANCING.
Now when irq_startup() runs with IRQ_STARTUP_NORMAL, it calls
irq_setup_affinity() which returns early because IRQF_PERCPU and
IRQF_NOBALANCING are set, leaving the interrupt on its original CPU."
This was broken by the recent commit which blocked interrupt affinity
setting in hardware before activation of the interrupt. While this works in
general, it does not work for this particular case. As contrary to the
initial analysis not all interrupt chip drivers implement an activate
callback, the safe cure is to make the deferred interrupt affinity setting
at activation time opt-in.
Implement the necessary core logic and make the two irqchip implementations
for which this is required opt-in. In hindsight this would have been the
right thing to do, but ...
Fixes: baedb87d1b ("genirq/affinity: Handle affinity setting on inactive interrupts correctly")
Reported-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/87blk4tzgm.fsf@nanos.tec.linutronix.de
When the system is suspended, we can explicitly disable clock to save
power. To achieve this, we need save registers' state since it could be
lost after power off.
Implement power management which will:
- Turn the clock off after probing
- Disable clock and save registers' state on system suspend, as
well as enable clock and restore registers' state on resume
- Rely on the Power Domain framework to shutdown the intmux
power domain
Without CONFIG_PM, the clock is always on after probe stage.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[maz: revamped commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200727141734.24890-2-qiangqing.zhang@nxp.com
Booting the latest kernel with DEBUG_ATOMIC_SLEEP=y on a GICv4.1 enabled
box, I get the following kernel splat:
[ 0.053766] BUG: sleeping function called from invalid context at mm/slab.h:567
[ 0.053767] in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/1
[ 0.053769] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.8.0-rc3+ #23
[ 0.053770] Call trace:
[ 0.053774] dump_backtrace+0x0/0x218
[ 0.053775] show_stack+0x2c/0x38
[ 0.053777] dump_stack+0xc4/0x10c
[ 0.053779] ___might_sleep+0xfc/0x140
[ 0.053780] __might_sleep+0x58/0x90
[ 0.053782] slab_pre_alloc_hook+0x7c/0x90
[ 0.053783] kmem_cache_alloc_trace+0x60/0x2f0
[ 0.053785] its_cpu_init+0x6f4/0xe40
[ 0.053786] gic_starting_cpu+0x24/0x38
[ 0.053788] cpuhp_invoke_callback+0xa0/0x710
[ 0.053789] notify_cpu_starting+0xcc/0xd8
[ 0.053790] secondary_start_kernel+0x148/0x200
# ./scripts/faddr2line vmlinux its_cpu_init+0x6f4/0xe40
its_cpu_init+0x6f4/0xe40:
allocate_vpe_l1_table at drivers/irqchip/irq-gic-v3-its.c:2818
(inlined by) its_cpu_init_lpis at drivers/irqchip/irq-gic-v3-its.c:3138
(inlined by) its_cpu_init at drivers/irqchip/irq-gic-v3-its.c:5166
It turned out that we're allocating memory using GFP_KERNEL (may sleep)
within the CPU hotplug notifier, which is indeed an atomic context. Bad
thing may happen if we're playing on a system with more than a single
CommonLPIAff group. Avoid it by turning this into an atomic allocation.
Fixes: 5e5168461c ("irqchip/gic-v4.1: VPE table (aka GICR_VPROPBASER) allocation")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200630133746.816-1-yuzenghui@huawei.com
EXTI lines are mainly used to wake-up system from CStop low power mode.
Currently, if a device wants to use a EXTI (direct) line as wakeup line,
it has to declare 2 interrupts:
- one for EXTI used to wake-up system (with dedicated_wake_irq api).
- one for GIC used to get the wake up reason inside the concerned IP.
This split is not really needed as each EXTI line is actually "linked " to
a GIC. So to avoid this useless double interrupt management in each
wake-up driver, this patch lets the STM32 EXTI driver abstract it by
mapping each EXTI line to his corresponding GIC.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200717140717.29606-1-alexandre.torgue@st.com
This driver can work as a platform driver. So covert it to a platform
driver.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Hanks Chen <hanks.chen@mediatek.com>
Link: https://lore.kernel.org/r/20200718000637.3632841-5-saravanak@google.com
This driver can work as a platform driver. So covert it to a platform
driver.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Hanks Chen <hanks.chen@mediatek.com>
Link: https://lore.kernel.org/r/20200718000637.3632841-4-saravanak@google.com
Switch the driver to use the helper macros. In addition to reducing the
number of lines, this also adds module unload protection (if the driver
is compiled as a module) by switching from module_platform_driver to
builtin_platform_driver.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200718000637.3632841-3-saravanak@google.com
Compiling an irqchip driver as a platform driver needs to bunch of
things to be done right:
- Making sure the parent domain is initialized first
- Making sure the device can't be unbound from sysfs
- Disallowing module unload if it's built as a module
- Finding the parent node
- Etc.
Instead of trying to make sure all future irqchip platform drivers get
this right, provide boilerplate macros that take care of all of this.
An example use would look something like this. Where acme_foo_init and
acme_bar_init are similar to what would be passed to IRQCHIP_DECLARE.
IRQCHIP_PLATFORM_DRIVER_BEGIN(acme_irq)
IRQCHIP_MATCH("acme,foo", acme_foo_init)
IRQCHIP_MATCH("acme,bar", acme_bar_init)
IRQCHIP_PLATFORM_DRIVER_END(acme_irq)
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200718000637.3632841-2-saravanak@google.com
The GICv4.1 spec tells us that it's CONSTRAINED UNPREDICTABLE to issue a
register-based invalidation operation for a vPEID not mapped to that RD,
or another RD within the same CommonLPIAff group.
To follow this rule, commit f3a059219b ("irqchip/gic-v4.1: Ensure mutual
exclusion between vPE affinity change and RD access") tried to address the
race between the RD accesses and the vPE affinity change, but somehow
forgot to take GICR_INVALLR into account. Let's take the vpe_lock before
evaluating vpe->col_idx to fix it.
Fixes: f3a059219b ("irqchip/gic-v4.1: Ensure mutual exclusion between vPE affinity change and RD access")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200720092328.708-1-yuzenghui@huawei.com
cpu_logical_map is only defined for CONFIG_SMP builds, when we are in an
UP configuration, the boot CPU is 0.
Fixes: 6468fc18b0 ("irqchip/irq-bcm7038-l1: Add PM support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200724184157.29150-1-f.fainelli@gmail.com
Allows qcom-pdc driver to be loaded as a permanent module
Also, due to the fact that IRQCHIP_DECLARE becomes a no-op when
building as a module, we have to replace it with platform driver
hooks explicitly.
Thanks to Saravana for his help on pointing out the
IRQCHIP_DECLARE issue and guidance on a solution.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20200710231824.60699-4-john.stultz@linaro.org
The sparse tool complains as follows:
drivers/irqchip/irq-mips-gic.c:49:1: warning:
symbol '__pcpu_scope_pcpu_masks' was not declared. Should it be static?
drivers/irqchip/irq-mips-gic.c:620:6: warning:
symbol 'gic_ipi_domain_free' was not declared. Should it be static?
drivers/irqchip/irq-mips-gic.c:634:5: warning:
symbol 'gic_ipi_domain_match' was not declared. Should it be static?
Those symbols are not used outside of irq-mips-gic.c, so marks
them static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200714142245.16124-1-weiyongjun1@huawei.com
Now that the hwspin_lock_timeout_in_atomic() API is available use it.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200706081115.25180-1-alexandre.torgue@st.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
In the function liointc_set_type(), we need to call the function
irq_gc_unlock_irqrestore() before returning.
Fixes: dbb1522679 ("irqchip: Add driver for Loongson I/O Local Interrupt Controller")
Reported-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-8-git-send-email-yangtiezhu@loongson.cn
irq_domain_alloc_irqs_parent() returns 0 on success and non-zero value
on failure, it is redudant to check its non-zero return value and then
return it, so just remove the variable "ret" and return directly in the
function pch_msi_parent_domain_alloc().
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-7-git-send-email-yangtiezhu@loongson.cn
Check the return value of irq_domain_translate_twocell() due to
it may returns -EINVAL if failed and use variable fwspec for it,
and then use a new variable parent_fwspec which is proper for
irq_domain_alloc_irqs_parent().
Fixes: ef8c01eb64 ("irqchip: Add Loongson PCH PIC controller")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-6-git-send-email-yangtiezhu@loongson.cn
In the function htvec_of_init(), system resource "parent_irq"
was not released in an error case. Thus add a jump target for
the completion of the desired exception handling.
Fixes: 818e915fba ("irqchip: Add Loongson HyperTransport Vector support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-4-git-send-email-yangtiezhu@loongson.cn
LOONGSON_HTPIC depends on MACH_LOONGSON64 and MACH_LOONGSON64 already
selects I8259 in arch/mips/Kconfig, so no need to select I8259 again
when config LOONGSON_HTPIC.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1594087972-21715-3-git-send-email-yangtiezhu@loongson.cn
We need to have a definition for cpu_logical_map[] which on ARM
platforms is provided by asm/smp_plat.h. This header is not
automatically included from linux/smp.h and untangling it is a bit
difficult.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709234141.4901-1-f.fainelli@gmail.com
The UPG_AUX_AON_INTR2 Level 2 interrupt controller node is defined with
the "brcm,upg-aux-aon-l2-intc" compatible string in Device Tree and
behaves as an edge triggered standard Broadcom STB L2 interrupt
controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-7-f.fainelli@gmail.com
The HIF_SPI_INTR2 Level 2 interrupt controller node is defined with the
"brcm,hif-spi-l2-intc" compatible string in Device Tree and behaves as
an edge triggered standard Broadcom STB L2 interrupt controller.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-5-f.fainelli@gmail.com
Utilize the Broadcom interrupt controller standard property
"brcm,irq-can-wake" to flag whether this particular interrupt controller
instance is wake-up capable.
Since we do not know what type of parent interrupt controller we are
interfaced with, ensure that enable_irq_wake() is called early on.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-3-f.fainelli@gmail.com
Utilize the Broadcom interrupt controller standard property
"brcm,irq-can-wake" to flag whether this particular interrupt controller
instance is wake-up capable.
Since we do not know what type of parent interrupt controller we are
interfaced with, ensure that enable_irq_wake() is called early on.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-2-f.fainelli@gmail.com
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl8DWosUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroO8cAf/UskNg8qoLGG17rQwhFpmigSllbiJ
TAyi3tpb1Y0Z2MfYeGkeiEb1L34bS28Cxl929DoqI3hrXy1wDCmsHPB5c3URXrzd
aswvr7pJtQV9iH1ykaS2woFJnOUovMFsFYMhj46yUPoAvdKOZKvuqcduxbogYHFw
YeRhS+1lGfiP2A0j3O/nnNJ0wq+FxKO46G3CgWeqG75+FSL6y/tl0bZJUMKKajQZ
GNaOv/CYCHAfUdvgy0ZitRD8lV8yxng3dYGjm+a52Kmn2ZWiFlxNrnxzHySk16Rn
Lq6MfFOqgrYpoZv7SnsFYnRE05U5bEFQ8BGr22fImQ+ktKDgq+9gv6cKwA==
=+DN/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Bugfixes and a one-liner patch to silence a sparse warning"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm64: Stop clobbering x0 for HVC_SOFT_RESTART
KVM: arm64: PMU: Fix per-CPU access in preemptible context
KVM: VMX: Use KVM_POSSIBLE_CR*_GUEST_BITS to initialize guest/host masks
KVM: x86: Mark CR4.TSD as being possibly owned by the guest
KVM: x86: Inject #GP if guest attempts to toggle CR4.LA57 in 64-bit mode
kvm: use more precise cast and do not drop __user
KVM: x86: bit 8 of non-leaf PDPEs is not reserved
KVM: X86: Fix async pf caused null-ptr-deref
KVM: arm64: vgic-v4: Plug race between non-residency and v4.1 doorbell
KVM: arm64: pvtime: Ensure task delay accounting is enabled
KVM: arm64: Fix kvm_reset_vcpu() return code being incorrect with SVE
KVM: arm64: Annotate hyp NMI-related functions as __always_inline
KVM: s390: reduce number of IO pins to 1
In an effort to enable -Wcast-function-type in the top-level Makefile to
support Control Flow Integrity builds, there are the need to remove all
the function callback casts.
To do this, modify the IRQCHIP_ACPI_DECLARE macro to use the new defined
macro ACPI_DECLARE_SUBTABLE_PROBE_ENTRY instead of the macro
ACPI_DECLARE_PROBE_ENTRY. This is necessary to be able to initialize the
the acpi_probe_entry struct using the probe_subtbl field instead of the
probe_table field and avoid function cast mismatches.
Also, modify the prototype of the functions used by the invocation of the
IRQCHIP_ACPI_DECLARE macro to match all the parameters.
Co-developed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Oscar Carter <oscar.carter@gmx.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20200530143430.5203-3-oscar.carter@gmx.com
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200616230923.GA24937@embeddedor
This driver may take a regular spinlock when a raw spinlock
(irq_desc->lock) is already taken which results in the following
lockdep splat:
=============================
[ BUG: Invalid wait context ]
5.7.0-rc7 #1 Not tainted
-----------------------------
swapper/0/0 is trying to lock:
ffffff800303b798 (&chip_data->lock){....}-{3:3}, at: mtk_sysirq_set_type+0x48/0xc0
other info that might help us debug this:
context-{5:5}
2 locks held by swapper/0/0:
#0: ffffff800302ee68 (&desc->request_mutex){....}-{4:4}, at: __setup_irq+0xc4/0x8a0
#1: ffffff800302ecf0 (&irq_desc_lock_class){....}-{2:2}, at: __setup_irq+0xe4/0x8a0
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.7.0-rc7 #1
Hardware name: Pumpkin MT8516 (DT)
Call trace:
dump_backtrace+0x0/0x180
show_stack+0x14/0x20
dump_stack+0xd0/0x118
__lock_acquire+0x8c8/0x2270
lock_acquire+0xf8/0x470
_raw_spin_lock_irqsave+0x50/0x78
mtk_sysirq_set_type+0x48/0xc0
__irq_set_trigger+0x58/0x170
__setup_irq+0x420/0x8a0
request_threaded_irq+0xd8/0x190
timer_of_init+0x1e8/0x2c4
mtk_gpt_init+0x5c/0x1dc
timer_probe+0x74/0xf4
time_init+0x14/0x44
start_kernel+0x394/0x4f0
Replace the spinlock_t with raw_spinlock_t to avoid this warning.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200615074445.3579-1-brgl@bgdev.pl
There are registers and functions in the header file
that are only used inside the driver. Move these into
the driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200607215124.48638-2-linus.walleij@linaro.org
It should be "ti.com" instead of "ticom".
Fixes: 9f1463b86c ("irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/1591437017-5295-3-git-send-email-yangtiezhu@loongson.cn
When call function devm_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Fixes: 9f1463b86c ("irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/1591437017-5295-2-git-send-email-yangtiezhu@loongson.cn
In the function ti_sci_inta_set_type(), the statement "return -EINVAL;"
out of switch case is dead code, remove it.
Fixes: 9f1463b86c ("irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/1591437017-5295-1-git-send-email-yangtiezhu@loongson.cn
When making a vPE non-resident because it has hit a blocking WFI,
the doorbell can fire at any time after the write to the RD.
Crucially, it can fire right between the write to GICR_VPENDBASER
and the write to the pending_last field in the its_vpe structure.
This means that we would overwrite pending_last with stale data,
and potentially not wakeup until some unrelated event (such as
a timer interrupt) puts the vPE back on the CPU.
GICv4 isn't affected by this as we actively mask the doorbell on
entering the guest, while GICv4.1 automatically manages doorbell
delivery without any hypervisor-driven masking.
Use the vpe_lock to synchronize such update, which solves the
problem altogether.
Fixes: ae699ad348 ("irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The GIC driver uses a RMW sequence to update the affinity, and
relies on the gic_lock_irqsave/gic_unlock_irqrestore sequences
to update it atomically.
But these sequences only expand into anything meaningful if
the BL_SWITCHER option is selected, which almost never happens.
It also turns out that using a RMW and locks is just as silly,
as the GIC distributor supports byte accesses for the GICD_TARGETRn
registers, which when used make the update atomic by definition.
Drop the terminally broken code and replace it by a byte write.
Fixes: 04c8b0f82c ("irqchip/gic: Make locking a BL_SWITCHER only feature")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Anup originally re-spun his patch set to include this fix, but it was a bit too
late for my PR so I've split it out.
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200611175302.253540-1-palmer@dabbelt.com
readx_poll_timeout() can sleep if @sleep_us is specified by the caller,
and is therefore unsafe to be used inside the atomic context, which is
this case when we use it to poll the GICR_VPENDBASER.Dirty bit in
irq_set_vcpu_affinity() callback.
Let's convert to its atomic version instead which helps to get the v4.1
board back to life!
Fixes: 96806229ca ("irqchip/gic-v4.1: Add support for VPENDBASER's Dirty+Valid signaling")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200605052345.1494-1-yuzenghui@huawei.com
Instead of directly calling RISC-V timer interrupt handler from
RISC-V local interrupt conntroller driver, this patch implements
RISC-V timer interrupt as a per-CPU interrupt using per-CPU APIs
of Linux IRQ subsystem.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The RISC-V per-HART local interrupt controller manages software
interrupts, timer interrupts, external interrupts (which are routed
via the platform level interrupt controller) and other per-HART
local interrupts.
We add a driver for the RISC-V local interrupt controller, which
eventually replaces the RISC-V architecture code, allowing for a
better split between arch code and drivers.
The driver is compliant with RISC-V Hart-Level Interrupt Controller
DT bindings located at:
Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt
Co-developed-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
[Palmer: Cleaned up warnings]
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
The plic_find_hart_id() can be useful to other interrupt controller
drivers (such as RISC-V local interrupt driver) so we rename this
function to riscv_of_parent_hartid() and place it in arch directory
along with riscv_of_processor_hartid().
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
This commit:
818e915fba: ("irqchip: Add Loongson HyperTransport Vector support")
Added a MIPS-only driver, but turned on compilation on all other architectures as well:
config LOONGSON_HTVEC
bool "Loongson3 HyperTransport Interrupt Vector Controller"
depends on MACH_LOONGSON64 || COMPILE_TEST
But this driver was never build tested on any other architecture than MIPS:
drivers/irqchip/irq-loongson-htvec.c: In function ‘htvec_irq_dispatch’:
drivers/irqchip/irq-loongson-htvec.c:59:3: error: implicit declaration of function ‘spurious_interrupt’; did you mean ‘smp_reboot_interrupt’? [-Werror=implicit-function-declaration]
Because spurious_interrupt() only exists on MIPS.
So make it MIPS-only.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This controller appears on Loongson LS7A family of PCH to transform
interrupts from PCI MSI into HyperTransport vectorized interrrupts
and send them to procrssor's HT vector controller.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200528152757.1028711-6-jiaxun.yang@flygoat.com
This controller appears on Loongson LS7A family of PCH to transform
interrupts from devices into HyperTransport vectorized interrrupts
and send them to procrssor's HT vector controller.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200528152757.1028711-4-jiaxun.yang@flygoat.com
This controller appears on Loongson-3 chips for receiving interrupt
vectors from PCH's PIC and PCH's PCIe MSI interrupts.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200528152757.1028711-2-jiaxun.yang@flygoat.com
For multiple PLIC instances, the plic_init() is called once for each
PLIC instance. Due to this we have two issues:
1. cpuhp_setup_state() is called multiple times
2. plic_starting_cpu() can crash for boot CPU if cpuhp_setup_state()
is called before boot CPU PLIC handler is available.
Address both issues by only initializing the HP notifiers when
the boot CPU setup is complete.
Fixes: f1ad1133b1 ("irqchip/sifive-plic: Add support for multiple PLICs")
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200518091441.94843-3-anup.patel@wdc.com
For multiple PLIC instances, each PLIC can only target a subset of
CPUs which is represented by "lmask" in the "struct plic_priv".
Currently, the default irq affinity for each PLIC interrupt is all
online CPUs which is illegal value for default irq affinity when we
have multiple PLIC instances. To fix this, we now set "lmask" as the
default irq affinity in for each interrupt in plic_irqdomain_map().
Fixes: f1ad1133b1 ("irqchip/sifive-plic: Add support for multiple PLICs")
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200518091441.94843-2-anup.patel@wdc.com
(E)PPIs are per-CPU interrupts, so we want each CPU to go and enable them
via enable_percpu_irq(); this also means we want IRQ_NOAUTOEN for them as
the autoenable would lead to calling irq_enable() instead of the more
appropriate irq_percpu_enable().
Calling irq_set_percpu_devid() is enough to get just that since it trickles
down to irq_set_percpu_devid_flags(), which gives us IRQ_NOAUTOEN (and a
few others). Setting IRQ_NOAUTOEN *again* right after this call is just
redundant, so don't do it.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200521223500.834-1-valentin.schneider@arm.com
When mapping a LPI, the ITS driver picks the first possible
affinity, which is in most cases CPU0, assuming that if
that's not suitable, someone will come and set the affinity
to something more interesting.
It apparently isn't the case, and people complain of poor
performance when many interrupts are glued to the same CPU.
So let's place the interrupts by finding the "least loaded"
CPU (that is, the one that has the fewer LPIs mapped to it).
So called 'managed' interrupts are an interesting case where
the affinity is actually dictated by the kernel itself, and
we should honor this.
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1575642904-58295-1-git-send-email-john.garry@huawei.com
Link: https://lore.kernel.org/r/20200515165752.121296-3-maz@kernel.org
In order to improve the distribution of LPIs among CPUs, let start by
tracking the number of LPIs assigned to CPUs, both for managed and
non-managed interrupts (as separate counters).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20200515165752.121296-2-maz@kernel.org
A PLIC may not be connected to all the cores. In that case, nr_contexts
may be less than num_possible_cpus. This requirement is only valid a single
PLIC is the only interrupt controller for the whole system.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: "Wesley W. Terpstra" <wesley@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Link: https://lore.kernel.org/r/20200512172636.96299-1-atish.patra@wdc.com
[Atish: Modified the commit text]
With an SMP configuration, gic_smp_init() calls set_smp_cross_call().
set_smp_cross_call() is marked with "__init".
So gic_smp_init() should also be marked with "__init".
gic_smp_init() is only called from gic_init_bases().
gic_init_bases() is also marked with "__init";
So marking gic_smp_init() with "__init" is fine.
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200422112857.4300-1-ingo.rohloff@lauterbach.com
Fix the following sparse warning:
drivers/irqchip/irq-bcm7038-l1.c:419:12: warning: symbol
'bcm7038_l1_of_init' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200417074036.46594-1-yanaijie@huawei.com
Fix the following sparse warning:
drivers/irqchip/irq-mvebu-icu.c:69:1: warning: symbol 'legacy_bindings'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200417074046.46771-1-yanaijie@huawei.com
Running a lockedp-enabled kernel on a vim3l board (Amlogic SM1)
leads to the following splat:
[ 13.557138] WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
[ 13.587485] ip/456 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 13.625922] ffff000059908cf0 (&irq_desc_lock_class){-.-.}-{2:2}, at: __setup_irq+0xf8/0x8d8
[ 13.632273] which would create a new lock dependency:
[ 13.637272] (&irq_desc_lock_class){-.-.}-{2:2} -> (&ctl->lock){+.+.}-{2:2}
[ 13.644209]
[ 13.644209] but this new dependency connects a HARDIRQ-irq-safe lock:
[ 13.654122] (&irq_desc_lock_class){-.-.}-{2:2}
[ 13.654125]
[ 13.654125] ... which became HARDIRQ-irq-safe at:
[ 13.664759] lock_acquire+0xec/0x368
[ 13.666926] _raw_spin_lock+0x60/0x88
[ 13.669979] handle_fasteoi_irq+0x30/0x178
[ 13.674082] generic_handle_irq+0x38/0x50
[ 13.678098] __handle_domain_irq+0x6c/0xc8
[ 13.682209] gic_handle_irq+0x5c/0xb0
[ 13.685872] el1_irq+0xd0/0x180
[ 13.689010] arch_cpu_idle+0x40/0x220
[ 13.692732] default_idle_call+0x54/0x60
[ 13.696677] do_idle+0x23c/0x2e8
[ 13.699903] cpu_startup_entry+0x30/0x50
[ 13.703852] rest_init+0x1e0/0x2b4
[ 13.707301] arch_call_rest_init+0x18/0x24
[ 13.711449] start_kernel+0x4ec/0x51c
[ 13.715167]
[ 13.715167] to a HARDIRQ-irq-unsafe lock:
[ 13.722426] (&ctl->lock){+.+.}-{2:2}
[ 13.722430]
[ 13.722430] ... which became HARDIRQ-irq-unsafe at:
[ 13.732319] ...
[ 13.732324] lock_acquire+0xec/0x368
[ 13.735985] _raw_spin_lock+0x60/0x88
[ 13.739452] meson_gpio_irq_domain_alloc+0xcc/0x290
[ 13.744392] irq_domain_alloc_irqs_hierarchy+0x24/0x60
[ 13.749586] __irq_domain_alloc_irqs+0x160/0x2f0
[ 13.754254] irq_create_fwspec_mapping+0x118/0x320
[ 13.759073] irq_create_of_mapping+0x78/0xa0
[ 13.763360] of_irq_get+0x6c/0x80
[ 13.766701] of_mdiobus_register_phy+0x10c/0x238 [of_mdio]
[ 13.772227] of_mdiobus_register+0x158/0x380 [of_mdio]
[ 13.777388] mdio_mux_init+0x180/0x2e8 [mdio_mux]
[ 13.782128] g12a_mdio_mux_probe+0x290/0x398 [mdio_mux_meson_g12a]
[ 13.788349] platform_drv_probe+0x5c/0xb0
[ 13.792379] really_probe+0xe4/0x448
[ 13.795979] driver_probe_device+0xe8/0x140
[ 13.800189] __device_attach_driver+0x94/0x120
[ 13.804639] bus_for_each_drv+0x84/0xd8
[ 13.808474] __device_attach+0xe4/0x168
[ 13.812361] device_initial_probe+0x1c/0x28
[ 13.816592] bus_probe_device+0xa4/0xb0
[ 13.820430] deferred_probe_work_func+0xa8/0x100
[ 13.825064] process_one_work+0x264/0x688
[ 13.829088] worker_thread+0x4c/0x458
[ 13.832768] kthread+0x154/0x158
[ 13.836018] ret_from_fork+0x10/0x18
[ 13.839612]
[ 13.839612] other info that might help us debug this:
[ 13.839612]
[ 13.850354] Possible interrupt unsafe locking scenario:
[ 13.850354]
[ 13.855720] CPU0 CPU1
[ 13.858774] ---- ----
[ 13.863242] lock(&ctl->lock);
[ 13.866330] local_irq_disable();
[ 13.872233] lock(&irq_desc_lock_class);
[ 13.878705] lock(&ctl->lock);
[ 13.884297] <Interrupt>
[ 13.886857] lock(&irq_desc_lock_class);
[ 13.891014]
[ 13.891014] *** DEADLOCK ***
The issue can occur when CPU1 is doing something like irq_set_type()
and CPU0 performing an interrupt allocation, for example. Taking
an interrupt (like the one being reconfigured) would lead to a deadlock.
A solution to this is:
- Reorder the locking so that meson_gpio_irq_update_bits takes the lock
itself at all times, instead of relying on the caller to lock or not,
hence making the RMW sequence atomic,
- Rework the critical section in meson_gpio_irq_request_channel to only
cover the allocation itself, and let the gpio_irq_sel_pin callback
deal with its own locking if required,
- Take the private spin-lock with interrupts disabled at all times
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
As per the PLIC specification, maximum priority threshold value is 0x7
not 0xF. Even though it doesn't cause any error in qemu/hifive unleashed,
there may be some implementation which checks the upper bound resulting in
an illegal access.
Fixes: ccbe80bad5 ("irqchip/sifive-plic: Enable/Disable external interrupts upon cpu online/offline")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200403014609.71831-1-atish.patra@wdc.com
The ti_sci_inta_irq_handler() does not take into account INTA IRQs state
(masked/unmasked) as it uses INTA_STATUS_CLEAR_j register to get INTA IRQs
status, which provides raw status value.
This causes hard IRQ handlers to be called or threaded handlers to be
scheduled many times even if corresponding INTA IRQ is masked.
Above, first of all, affects the LEVEL interrupts processing and causes
unexpected behavior up the system stack or crash.
Fix it by using the Interrupt Masked Status INTA_STATUSM_j register which
provides masked INTA IRQs status.
Fixes: 9f1463b86c ("irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200408191532.31252-1-grygorii.strashko@ti.com
Cc: stable@vger.kernel.org
Using irq_domain_free_irqs_common() on the irqdomain free path will
leave the MSI descriptor unfreed when platform devices get removed.
Properly free it by MSI domain free function.
Fixes: 9650c60ebf ("irqchip/mbigen: Create irq domain for each mbigen device")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200408114352.1604-1-yuzenghui@huawei.com
Although the vSGIs are not directly visible to the host, they still
get moved around by the CPU hotplug, for example. This results in
the kernel moaning on the console, such as:
genirq: irq_chip GICv4.1-sgi did not update eff. affinity mask of irq 38
Updating the effective affinity on set_affinity() fixes it.
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When a vPE is made resident, the GIC starts parsing the virtual pending
table to deliver pending interrupts. This takes place asynchronously,
and can at times take a long while. Long enough that the vcpu enters
the guest and hits WFI before any interrupt has been signaled yet.
The vcpu then exits, blocks, and now gets a doorbell. Rince, repeat.
In order to avoid the above, a (optional on GICv4, mandatory on v4.1)
feature allows the GIC to feedback to the hypervisor whether it is
done parsing the VPT by clearing the GICR_VPENDBASER.Dirty bit.
The hypervisor can then wait until the GIC is ready before actually
running the vPE.
Plug the detection code as well as polling on vPE schedule. While
at it, tidy-up the kernel message that displays the GICv4 optional
features.
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
driver which affected the PPC users.
-----BEGIN PGP SIGNATURE-----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=pZAC
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-04-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two reverts addressing regressions of the Xilinx interrupt controller
driver which affected the PPC users"
* tag 'irq-urgent-2020-04-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "irqchip/xilinx: Enable generic irq multi handler"
Revert "irqchip/xilinx: Do not call irq_set_default_host()"
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early. Most cleanup changes come
through the various maintainer trees, so the final removal of
setup_irq() is postponed towards the end of the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and unsafe
interrupt injection including a fixup of the offending PCI/AER error
injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside of
an actual interrupt, can cause inconsistent state on the fragile
x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=DZ/G
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early.
Most cleanup changes come through the various maintainer trees, so
the final removal of setup_irq() is postponed towards the end of
the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and
unsafe interrupt injection including a fixup of the offending
PCI/AER error injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside
of an actual interrupt, can cause inconsistent state on the
fragile x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place"
* tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
unicore32: Replace setup_irq() by request_irq()
sh: Replace setup_irq() by request_irq()
hexagon: Replace setup_irq() by request_irq()
c6x: Replace setup_irq() by request_irq()
alpha: Replace setup_irq() by request_irq()
irqchip/gic-v4.1: Eagerly vmap vPEs
irqchip/gic-v4.1: Add VSGI property setup
irqchip/gic-v4.1: Add VSGI allocation/teardown
irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer
irqchip/gic-v4.1: Plumb set_vcpu_affinity SGI callbacks
irqchip/gic-v4.1: Plumb get/set_irqchip_state SGI callbacks
irqchip/gic-v4.1: Plumb mask/unmask SGI callbacks
irqchip/gic-v4.1: Add initial SGI configuration
irqchip/gic-v4.1: Plumb skeletal VSGI irqchip
irqchip/stm32: Retrigger both in eoi and unmask callbacks
irqchip/gic-v3: Move irq_domain_update_bus_token to after checking for NULL domain
irqchip/xilinx: Do not call irq_set_default_host()
irqchip/xilinx: Enable generic irq multi handler
irqchip/xilinx: Fill error code when irq domain registration fails
irqchip/xilinx: Add support for multiple instances
...
This controller appeared on Loongson-3 family of chips to receive
interrupts from PCH PIC.
It is a I8259 with optimized interrupt polling flow. We can poll
interrupt number from HT vector directly but still have to follow
standard I8259 routines to mask, unmask and EOI.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The 1.0 version of that controller has a bug that status bit
of LPC IRQ sometimes doesn't get set correctly.
So we can always blame LPC IRQ when spurious interrupt happens
at the parent interrupt line which LPC IRQ supposed to route
to.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This controller appeared on Loongson family of chips as the primary
package interrupt source.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Now that we have HW-accelerated SGIs being delivered to VPEs, it
becomes required to map the VPEs on all ITSs instead of relying
on the lazy approach that we would use when using the ITS-list
mechanism.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-17-maz@kernel.org
In order to hide some of the differences between v4.0 and v4.1, move
the doorbell management out of the KVM code, and into the GICv4-specific
layer. This allows the calling code to ask for the doorbell when blocking,
and otherwise to leave the doorbell permanently disabled.
This matches the v4.1 code perfectly, and only results in a minor
refactoring of the v4.0 code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-14-maz@kernel.org
Just like for vLPIs, there is some configuration information that cannot
be directly communicated through the normal irqchip API, and we have to
use our good old friend set_vcpu_affinity as a side-band communication
mechanism.
This is used to configure group and priority for a given vSGI.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-13-maz@kernel.org
To implement the get/set_irqchip_state callbacks (limited to the
PENDING state), we have to use a particular set of hacks:
- Reading the pending state is done by using a pair of new redistributor
registers (GICR_VSGIR, GICR_VSGIPENDR), which allow the 16 interrupts
state to be retrieved.
- Setting the pending state is done by generating it as we'd otherwise do
for a guest (writing to GITS_SGIR).
- Clearing the pending state is done by emitting a VSGI command with the
"clear" bit set.
This requires some interesting locking though:
- When talking to the redistributor, we must make sure that the VPE
affinity doesn't change, hence taking the VPE lock.
- At the same time, we must ensure that nobody accesses the same
redistributor's GICR_VSGIR registers for a different VPE, which
would corrupt the reading of the pending bits. We thus take the
per-RD spinlock. Much fun.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-12-maz@kernel.org
Implement mask/unmask for virtual SGIs by calling into the
configuration helper.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-11-maz@kernel.org
The GICv4.1 ITS has yet another new command (VSGI) which allows
a VPE-targeted SGI to be configured (or have its pending state
cleared). Add support for this command and plumb it into the
activate irqdomain callback so that it is ready to be used.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-10-maz@kernel.org
Since GICv4.1 has the capability to inject 16 SGIs into each VPE,
and that I'm keen not to invent too many specific interfaces to
manipulate these interrupts, let's pretend that each of these SGIs
is an actual Linux interrupt.
For that matter, let's introduce a minimal irqchip and irqdomain
setup that will get fleshed up in the following patches.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-9-maz@kernel.org
Register default arch handler via driver instead of directly pointing to
xilinx intc controller. This patch makes architecture code more generic.
Driver calls generic domain specific irq handler which does the most of
things self. Also get rid of concurrent_irq counting which hasn't been
exported anywhere.
Based on this loop was also optimized by using do/while loop instead of
goto loop.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stefan Asserhall <stefan.asserhall@xilinx.com>
Link: https://lore.kernel.org/r/20200317125600.15913-4-mubin.usman.sayyed@xilinx.com
Added support for cascaded interrupt controllers.
Following cascaded configurations have been tested,
- peripheral->xilinx-intc->xilinx-intc->gic->Cortexa53 processor
on zcu102 board
- peripheral->xilinx-intc->xilinx-intc->microblaze processor
on kcu105 board
Signed-off-by: Mubin Sayyed <mubin.usman.sayyed@xilinx.com>
Signed-off-by: Anirudha Sarangi <anirudha.sarangi@xilinx.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200317125600.15913-2-mubin.usman.sayyed@xilinx.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200319214531.GA21326@embeddedor.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200319214438.GA21123@embeddedor.com
Clear its own IRQs before the parent IRQ get enabled, so that the
remaining IRQs do not accidentally interrupt the parent IRQ controller.
This patch also fixes a reboot bug on OX820 SoC, where the remaining
rps-timer IRQ raises a GIC interrupt that is left pending. After that,
the rps-timer IRQ is cleared during driver initialization, and there's
no IRQ left in rps-irq when local_irq_enable() is called, which evokes
an error message "unexpected IRQ trap".
Fixes: bdd272cbb9 ("irqchip: versatile FPGA: support cascaded interrupts from DT")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200321133842.2408823-1-mans0n@gorani.run
There is no special reason to set virtual LPI pending table as
non-shareable. If we choose to hard code the shareability without
probing, Inner-Shareable is likely to be a better choice, as the
VPEs can move around and benefit from having the redistributors
snooping each other's cache, if that's something they can do.
Furthermore, Hisilicon hip08 ends up with unspecified errors when
mixing shareability attributes. So let's move to IS attributes for
the VPT. This has also been tested on D05 and didn't show any
regression.
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
[maz: rewrote commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191130073849.38378-1-guoheyi@huawei.com
One of the new features of GICv4.1 is to allow virtual SGIs to be
directly signaled to a VPE. For that, the ITS has grown a new
64kB page containing only a single register that is used to
signal a SGI to a given VPE.
Add a second mapping covering this new 64kB range, and take this
opportunity to limit the original mapping to 64kB, which is enough
to cover the span of the ITS registers.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-8-maz@kernel.org
Tell KVM that we support v4.1. Nothing uses this information so far.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-7-maz@kernel.org
The GICv4.1 spec says that it is CONTRAINED UNPREDICTABLE to write to
any of the GICR_INV{LPI,ALL}R registers if GICR_SYNCR.Busy == 1.
To deal with it, we must ensure that only a single invalidation can
happen at a time for a given redistributor. Add a per-RD lock to that
effect and take it around the invalidation/syncr-read to deal with this.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-6-maz@kernel.org
In GICv4.1, we emulate a guest-issued INVALL command by a direct write
to GICR_INVALLR. Before we finish the emulation and go back to guest,
let's make sure the physical invalidate operation is actually completed
and no stale data will be left in redistributor. Per the specification,
this can be achieved by polling the GICR_SYNCR.Busy bit (to zero).
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200302092145.899-1-yuzenghui@huawei.com
Link: https://lore.kernel.org/r/20200304203330.4967-5-maz@kernel.org
Before GICv4.1, all operations would be serialized with the affinity
changes by virtue of using the same ITS command queue. With v4.1, things
change, as invalidations (and a number of other operations) are issued
using the redistributor MMIO frame.
We must thus make sure that these redistributor accesses cannot race
against aginst the affinity change, or we may end-up talking to the
wrong redistributor.
To ensure this, we expand the irq_to_cpuid() helper to take a spinlock
when the LPI is mapped to a vLPI (a new per-VPE lock) on each operation
that requires mutual exclusion.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-4-maz@kernel.org
In a system that is only sparsly populated with CPUs, we can end-up with
redistributors structures that are not initialized. Let's make sure we
don't try and access those when iterating over them (in this case when
checking we have a L2 VPE table).
Fixes: 4e6437f12d ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-3-maz@kernel.org
To allow the direct injection of SGIs into a guest, the GICv4.1
architecture has to sacrifice the Active state so that SGIs look
a lot like LPIs (they are injected by the same mechanism).
In order not to break existing software, the architecture gives
offers guests OSs the choice: SGIs with or without an active
state. It is the hypervisors duty to honor the guest's choice.
For this, the architecture offers a discovery bit indicating whether
the GIC supports GICv4.1 SGIs (GICD_TYPER2.nASSGIcap), and another
bit indicating whether the guest wants Active-less SGIs or not
(controlled by GICD_CTLR.nASSGIreq).
A hypervisor not supporting GICv4.1 SGIs would leave nASSGIcap
clear, and a guest not knowing about GICv4.1 SGIs (or definitely
wanting an Active state) would leave nASSGIreq clear (both being
thankfully backward compatible with older revisions of the GIC).
Since Linux is perfectly happy without an active state on SGIs,
inform the hypervisor that we'll use that if offered.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-2-maz@kernel.org
Enclose the chained handler with chained_irq_{enter,exit}(), so that the
muxed interrupts get properly acked.
This patch also fixes a reboot bug on OX820 SoC, where the jiffies timer
interrupt is never acked. The kernel waits a clock tick forever in
calibrate_delay_converge(), which leads to a boot hang.
Fixes: c41b16f8c9 ("ARM: integrator/versatile: consolidate FPGA IRQ handling code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200319023448.1479701-1-mans0n@gorani.run
The irq_retrigger callback is supposed to return 0 when retrigger
has failed, and a non-zero value otherwise. Tell the core code
that the driver has succedded in using the HW to retrigger the
interrupt.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200310184921.23552-3-maz@kernel.org
The irq_retrigger callback is supposed to return 0 when retrigger
has failed, and a non-zero value otherwise. Tell the core code
that the driver has succedded in using the HW to retrigger the
interrupt.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200310184921.23552-2-maz@kernel.org
The GICv3 ITS driver assumes that once it has latched on a page size for
a given BASER register, it can use the same page size as the maximum
page size for all subsequent BASER registers.
Although it worked so far, nothing in the architecture guarantees this,
and Nianyao Tang hit this problem on some undisclosed implementation.
Let's bite the bullet and probe the the supported page size on all BASER
registers before starting to populate the tables. This simplifies the
setup a bit, at the expense of a few additional MMIO accesses.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reported-by: Nianyao Tang <tangnianyao@huawei.com>
Tested-by: Nianyao Tang <tangnianyao@huawei.com>
Link: https://lore.kernel.org/r/1584089195-63897-1-git-send-email-zhangshaokun@hisilicon.com
Per the spec, the BCM2835's IRQs are all disabled when coming out of
power-on reset. Its IRQ driver assumes that's still the case when the
kernel boots and does not perform any initialization of the registers.
However the Raspberry Pi Foundation's bootloader leaves the USB
interrupt enabled when handing over control to the kernel.
Quiesce IRQs and the FIQ if they were left enabled and log a message to
let users know that they should update the bootloader once a fixed
version is released.
If the USB interrupt is not quiesced and the USB driver later on claims
the FIQ (as it does on the Raspberry Pi Foundation's downstream kernel),
interrupt latency for all other peripherals increases and occasional
lockups occur. That's because both the FIQ and the normal USB interrupt
fire simultaneously:
On a multicore Raspberry Pi, if normal interrupts are routed to CPU 0
and the FIQ to CPU 1 (hardcoded in the Foundation's kernel), then a USB
interrupt causes CPU 0 to spin in bcm2836_chained_handle_irq() until the
FIQ on CPU 1 has cleared it. Other peripherals' interrupts are starved
as long. I've seen CPU 0 blocked for up to 2.9 msec. eMMC throughput
on a Compute Module 3 irregularly dips to 23.0 MB/s without this commit
but remains relatively constant at 23.5 MB/s with this commit.
The lockups occur when CPU 0 receives a USB interrupt while holding a
lock which CPU 1 is trying to acquire while the FIQ is temporarily
disabled on CPU 1. At best users get RCU CPU stall warnings, but most
of the time the system just freezes.
Fixes: 89214f009c ("ARM: bcm2835: add interrupt controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/f97868ba4e9b86ddad71f44ec9d8b3b7d8daa1ea.1582618537.git.lukas@wunner.de
Current, PLIC driver can support only 1 PLIC on the board. However,
there can be multiple PLICs present on a two socket systems in RISC-V.
Modify the driver so that each PLIC handler can have a information
about individual PLIC registers and an irqdomain associated with it.
Tested on two socket RISC-V system based on VCU118 FPGA connected via
OmniXtend protocol.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20200302231146.15530-3-atish.patra@wdc.com
Currently, PLIC threshold is only initialized once in the beginning.
However, threshold can be set to disabled if a CPU is marked offline with
CPU hotplug feature. This will not allow to change the irq affinity to a
CPU that just came online.
Add PLIC specific CPU hotplug callbacks and enable the threshold when a CPU
comes online. Take this opportunity to move the external interrupt enable
code from trap init to PLIC driver as well. On cpu offline path, the driver
performs the exact opposite operations i.e. disable the interrupt and
the threshold.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20200302231146.15530-2-atish.patra@wdc.com
Restore alignment of the continuation of the devm_ioremap() call in
intc_irqpin_probe().
Fixes: 4bdc0d676a ("remove ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200212084744.9376-1-geert+renesas@glider.be
GICR_SYNCR is a 32bit register, so it is better to access it with
32bit access width, though we have not seen any real problem.
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200225090023.28020-1-guoheyi@huawei.com
This commit introduces retrigger support for stm32_ext_h chip.
It consists to rise the GIC interrupt mapped to an EXTI line.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200219143229.18084-2-alexandre.torgue@st.com
When transitioning some elder platforms to device tree it
becomes necessary to cascade VIC IRQ chips off another
interrupt controller.
Tested with the cascaded VIC on the Integrator/AP attached
logic module IM-PD1.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200219153543.137153-1-linus.walleij@linaro.org
In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.
Fixes: 4e6437f12d ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
V{PEND,PROP}BASER registers are actually located in VLPI_base frame
of the *redistributor*. Rename their accessors to reflect this fact.
No functional changes.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-7-yuzenghui@huawei.com
"ITS virtual pending table not cleaning" is already complained inside
its_clear_vpend_valid(), there's no need to trigger a WARN_ON again.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-6-yuzenghui@huawei.com
In GICv4, we will ensure that level2 vPE table memory is allocated
for the specified vpe_id on all v4 ITS, in its_alloc_vpe_table().
This still works well for the typical GICv4.1 implementation, where
the new vPE table is shared between the ITSs and the RDs.
To make it explicit, let us introduce allocate_vpe_l2_table() to
make sure that the L2 tables are allocated on all v4.1 RDs. We're
likely not need to allocate memory in it because the vPE table is
shared and (L2 table is) already allocated at ITS level, except
for the case where the ITS doesn't share anything (say SVPET == 0,
practically unlikely but architecturally allowed).
The implementation of allocate_vpe_l2_table() is mostly copied from
its_alloc_table_entry().
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-4-yuzenghui@huawei.com
Currently, we will not set vpe_l1_page for the current RD if we can
inherit the vPE configuration table from another RD (or ITS), which
results in an inconsistency between RDs within the same CommonLPIAff
group.
Let's rename it to vpe_l1_base to indicate the base address of the
vPE configuration table of this RD, and set it properly for *all*
v4.1 redistributors.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-3-yuzenghui@huawei.com
The Size field of GICv4.1 VPROPBASER register indicates number of
pages minus one and together Page_Size and Size control the vPEID
width. Let's respect this requirement of the architecture.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-2-yuzenghui@huawei.com
It looks like an obvious mistake to use its_mapc_cmd descriptor when
building the INVALL command block. It so far worked by luck because
both its_mapc_cmd.col and its_invall_cmd.col sit at the same offset of
the ITS command descriptor, but we should not rely on it.
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191202071021.1251-1-yuzenghui@huawei.com
We currently allocate redistributor region structures for
individual redistributors when ACPI doesn't present us with
compact MMIO regions covering multiple redistributors.
It turns out that we allocate these structures even when
the redistributor is flagged as disabled by ACPI. It works
fine until someone actually tries to tarse one of these
structures, and access the corresponding MMIO region.
Instead, track the number of enabled redistributors, and
only allocate what is required. This makes sure that there
is no invalid data to misuse.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reported-by: Heyi Guo <guoheyi@huawei.com>
Tested-by: Heyi Guo <guoheyi@huawei.com>
Link: https://lore.kernel.org/r/20191216062745.63397-1-guoheyi@huawei.com
- A mechanism to shield isolated tasks from managed interrupts:
The affinity of managed interrupts is completely controlled by the
kernel and user space has no influence on them. The reason is that
the automatically assigned affinity correlates to the multi-queue
CPU handling of block devices.
If the generated affinity mask spaws both housekeeping and isolated CPUs
the interrupt could be routed to an isolated CPU which would then be
disturbed by I/O submitted by a housekeeping CPU.
The new mechamism ensures that as long as one housekeeping CPU is online
in the assigned affinity mask the interrupt is routed to a housekeeping
CPU.
If there is no online housekeeping CPU in the affinity mask, then the
interrupt is routed to an isolated CPU to keep the device queue intact,
but unless the isolated CPU submits I/O by itself these interrupts are
not raised.
- A small addon to the device tree irqdomain core code to avoid
duplication in irq chip drivers
- Conversion of the SiFive PLIC to hierarchical domains
- The usual pile of new irq chip drivers: SiFive GPIO, Aspeed SCI, NXP
INTMUX, Meson A1 GPIO
- The first cut of support for the new ARM GICv4.1
- The usual pile of fixes and improvements in core and driver code
-----BEGIN PGP SIGNATURE-----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=E2VR
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The interrupt departement provides:
- A mechanism to shield isolated tasks from managed interrupts:
The affinity of managed interrupts is completely controlled by the
kernel and user space has no influence on them. The reason is that
the automatically assigned affinity correlates to the multi-queue
CPU handling of block devices.
If the generated affinity mask spaws both housekeeping and isolated
CPUs the interrupt could be routed to an isolated CPU which would
then be disturbed by I/O submitted by a housekeeping CPU.
The new mechamism ensures that as long as one housekeeping CPU is
online in the assigned affinity mask the interrupt is routed to a
housekeeping CPU.
If there is no online housekeeping CPU in the affinity mask, then
the interrupt is routed to an isolated CPU to keep the device queue
intact, but unless the isolated CPU submits I/O by itself these
interrupts are not raised.
- A small addon to the device tree irqdomain core code to avoid
duplication in irq chip drivers
- Conversion of the SiFive PLIC to hierarchical domains
- The usual pile of new irq chip drivers: SiFive GPIO, Aspeed SCI,
NXP INTMUX, Meson A1 GPIO
- The first cut of support for the new ARM GICv4.1
- The usual pile of fixes and improvements in core and driver code"
* tag 'irq-core-2020-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
genirq, sched/isolation: Isolate from handling managed interrupts
irqchip/gic-v4.1: Allow direct invalidation of VLPIs
irqchip/gic-v4.1: Suppress per-VLPI doorbell
irqchip/gic-v4.1: Add VPE INVALL callback
irqchip/gic-v4.1: Add VPE eviction callback
irqchip/gic-v4.1: Add VPE residency callback
irqchip/gic-v4.1: Add mask/unmask doorbell callbacks
irqchip/gic-v4.1: Plumb skeletal VPE irqchip
irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP
irqchip/gic-v4.1: Don't use the VPE proxy if RVPEID is set
irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP
irqchip/gic-v4.1: VPE table (aka GICR_VPROPBASER) allocation
irqchip/gic-v3: Add GICv4.1 VPEID size discovery
irqchip/gic-v3: Detect GICv4.1 supporting RVPEID
irqchip/gic-v3-its: Fix get_vlpi_map() breakage with doorbells
irqdomain: Fix a memory leak in irq_domain_push_irq()
irqchip: Add NXP INTMUX interrupt multiplexer support
dt-bindings: interrupt-controller: Add binding for NXP INTMUX interrupt multiplexer
irqchip: Define EXYNOS_IRQ_COMBINER
irqchip/meson-gpio: Add support for meson a1 SoCs
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
- Conversion of the SiFive PLIC to hierarchical domains
- New SiFive GPIO irqchip driver
- New Aspeed SCI irqchip driver
- New NXP INTMUX irqchip driver
- Additional support for the Meson A1 GPIO irqchip
- First part of the GICv4.1 support
- Assorted fixes
-----BEGIN PGP SIGNATURE-----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=8iz1
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Conversion of the SiFive PLIC to hierarchical domains
- New SiFive GPIO irqchip driver
- New Aspeed SCI irqchip driver
- New NXP INTMUX irqchip driver
- Additional support for the Meson A1 GPIO irqchip
- First part of the GICv4.1 support
- Assorted fixes
Just like for INVALL, GICv4.1 has grown a VPE-aware INVLPI register.
Let's plumb it in and make use of the DirectLPI code in that case.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-16-maz@kernel.org
Since GICv4.1 gives us a per-VPE doorbell, avoid programming anything
else on VMOVI/VMAPI/VMAPTI and on any other action that would have
otherwise resulted in a per-VLPI doorbell to be programmed.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-15-maz@kernel.org
GICv4.1 redistributors have a VPE-aware INVALL register. Progress!
We can now emulate a guest-requested INVALL without emiting a
VINVALL command.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-14-maz@kernel.org
When descheduling a VPE, special care must be taken to tell the GIC
about whether we want to receive a doorbell or not. This is a
major improvement on GICv4.0, where the doorbell had to be separately
enabled/disabled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-13-maz@kernel.org
Making a VPE resident on GICv4.1 is pretty simple, as it is just a
single write to the local redistributor. We just need extra information
about which groups to enable, which the KVM code will have to provide.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-12-maz@kernel.org
masking/unmasking doorbells on GICv4.1 relies on a new INVDB command,
which broadcasts the invalidation to all RDs.
Implement the new command as well as the masking callbacks, and plug
the whole thing into the v4.1 VPE irqchip.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-11-maz@kernel.org
Just like for GICv4.0, each VPE has its own doorbell interrupt, and
thus an irqchip that manages them. Since the doorbell management is
quite different on GICv4.1, let's introduce an almost empty irqchip
the will get populated over the next new patches.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-10-maz@kernel.org
With GICv4.1, VMOVP is extended to allow a default doorbell to be
specified, as well as a validity bit for this doorbell. As an added
bonus, VMOVP isn't required anymore of moving a VPE between
redistributors that share the same affinity.
Let's add this support to the VMOVP builder, and make sure we don't
issue the command if we don't really need to.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-9-maz@kernel.org
The infamous VPE proxy device isn't used with GICv4.1 because:
- we can invalidate any LPI from the DirectLPI MMIO interface
- the ITS and redistributors understand the life cycle of
the doorbell, so we don't need to enable/disable it all
the time
So let's escape early from the proxy related functions.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-8-maz@kernel.org
The ITS VMAPP command gains some new fields with GICv4.1:
- a default doorbell, which allows a single doorbell to be used for
all the VLPIs routed to a given VPE
- a pointer to the configuration table (instead of having it in a register
that gets context switched)
- a flag indicating whether this is the first map or the last unmap for
this particular VPE
- a flag indicating whether the pending table is known to be zeroed, or not
Plumb in the new fields in the VMAPP builder, and add the map/unmap
refcounting so that the ITS can do the right thing.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-7-maz@kernel.org
GICv4.1 defines a new VPE table that is potentially shared between
both the ITSs and the redistributors, following complicated affinity
rules.
To make things more confusing, the programming of this table at
the redistributor level is reusing the GICv4.0 GICR_VPROPBASER register
for something completely different.
The code flow is somewhat complexified by the need to respect the
affinities required by the HW, meaning that tables can either be
inherited from a previously discovered ITS or redistributor.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-6-maz@kernel.org
While GICv4.0 mandates 16 bit worth of VPEIDs, GICv4.1 allows smaller
implementations to be built. Add the required glue to dynamically
compute the limit.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-3-maz@kernel.org
GICv4.1 supports the RVPEID ("Residency per vPE ID"), which allows for
a much efficient way of making virtual CPUs resident (to allow direct
injection of interrupts).
The functionnality needs to be discovered on each and every redistributor
in the system, and disabled if the settings are inconsistent.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-2-maz@kernel.org
When updating an LPI configuration, get_vlpi_map() may be passed a
irq_data structure relative to an ITS domain (the normal case) or one
that is relative to the core GICv3 domain in the case of a GICv4
doorbell.
In the latter case, special care must be take not to dereference
the irq_chip data as an its_dev structure, as that isn't what is
stored there. Instead, check *first* whether the IRQ is forwarded
to a vcpu, and only then try to obtain the vlpi mapping.
Fixes: c1d4d5cd20 ("irqchip/gic-v3-its: Add its_vlpi_map helpers")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200122085609.658-1-yuzenghui@huawei.com
The Interrupt Multiplexer (INTMUX) expands the number of peripherals
that can interrupt the core:
* The INTMUX has 8 channels that are assigned to 8 NVIC interrupt slots.
* Each INTMUX channel can receive up to 32 interrupt sources and has 1
interrupt output.
* The INTMUX routes the interrupt sources to the interrupt outputs.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200117060653.27485-3-qiangqing.zhang@nxp.com
This patch is written to clean up dependency of ARCH_EXYNOS
Not all exynos device have IRQ_COMBINER, especially aarch64 EXYNOS
but it is built for all exynos devices.
Thus add the config for EXYNOS_IRQ_COMBINER
remove direct dependency between ARCH_EXYNOS and exynos-combiner.c
and only selected on the aarch32 devices
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191224211108.7128-1-hyunki00.koo@gmail.com
The meson a1 Socs have some changes compared with previous
chips. For A113L, it contains 62 pins and can be spied on:
- 62:128 undefined
- 61:50 12 pins on bank A
- 49:37 13 pins on bank F
- 36:20 17 pins on bank X
- 19:13 7 pins on bank B
- 12:0 13 pins on bank P
There are five relative registers for gpio interrupt controller,
details are as below:
- PADCTRL_GPIO_IRQ_CTRL0
bit[31]: enable/disable the whole irq lines
bit[16-23]: both edge trigger
bit[8-15]: single edge trigger
bit[0-7]: pol trigger
- PADCTRL_GPIO_IRQ_CTRL[X]
bit[0-6]: 7 bits to choose gpio source for irq line 2*[X] - 2
bit[16-22]: 7 bits to choose gpio source for irq line 2*[X] - 1
where X =1,2,3,4
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191216123645.10099-4-qianggui.song@amlogic.com
Since Meson-A1 SoCs register layout of gpio interrupt controller has
difference with previous chips, registers to decide irq line and offset
of trigger method are all changed, the current driver should be modified.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191216123645.10099-3-qianggui.song@amlogic.com
The following crash can be seen for setting
CONFIG_DEBUG_TEST_DRIVER_REMOVE=y for DT FW (which some people still use):
Hisilicon MBIGEN-V2 60080000.interrupt-controller: Failed to create mbi-gen irqdomain
Hisilicon MBIGEN-V2: probe of 60080000.interrupt-controller failed with error -12
[...]
Unable to handle kernel paging request at virtual address 0000000000005008
Mem abort info:
ESR = 0x96000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=0000041fb9990000
[0000000000005008] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 5.5.0-rc6-00002-g3fc42638a506-dirty #1622
Hardware name: Huawei Taishan 2280 /D05, BIOS Hisilicon D05 IT21 Nemo 2.0 RC0 04/18/2018
pstate: 40000085 (nZcv daIf -PAN -UAO)
pc : mbigen_set_type+0x38/0x60
lr : __irq_set_trigger+0x6c/0x188
sp : ffff800014b4b400
x29: ffff800014b4b400 x28: 0000000000000007
x27: 0000000000000000 x26: 0000000000000000
x25: ffff041fd83bd0d4 x24: ffff041fd83bd188
x23: 0000000000000000 x22: ffff80001193ce00
x21: 0000000000000004 x20: 0000000000000000
x19: ffff041fd83bd000 x18: ffffffffffffffff
x17: 0000000000000000 x16: 0000000000000000
x15: ffff8000119098c8 x14: ffff041fb94ec91c
x13: ffff041fb94ec1a1 x12: 0000000000000030
x11: 0101010101010101 x10: 0000000000000040
x9 : 0000000000000000 x8 : ffff041fb98c6680
x7 : ffff800014b4b380 x6 : ffff041fd81636c8
x5 : 0000000000000000 x4 : 000000000000025f
x3 : 0000000000005000 x2 : 0000000000005008
x1 : 0000000000000004 x0 : 0000000080000000
Call trace:
mbigen_set_type+0x38/0x60
__setup_irq+0x744/0x900
request_threaded_irq+0xe0/0x198
pcie_pme_probe+0x98/0x118
pcie_port_probe_service+0x38/0x78
really_probe+0xa0/0x3e0
driver_probe_device+0x58/0x100
__device_attach_driver+0x90/0xb0
bus_for_each_drv+0x64/0xc8
__device_attach+0xd8/0x138
device_initial_probe+0x10/0x18
bus_probe_device+0x90/0x98
device_add+0x4c4/0x770
device_register+0x1c/0x28
pcie_port_device_register+0x1e4/0x4f0
pcie_portdrv_probe+0x34/0xd8
local_pci_probe+0x3c/0xa0
pci_device_probe+0x128/0x1c0
really_probe+0xa0/0x3e0
driver_probe_device+0x58/0x100
__device_attach_driver+0x90/0xb0
bus_for_each_drv+0x64/0xc8
__device_attach+0xd8/0x138
device_attach+0x10/0x18
pci_bus_add_device+0x4c/0xb8
pci_bus_add_devices+0x38/0x88
pci_host_probe+0x3c/0xc0
pci_host_common_probe+0xf0/0x208
hisi_pcie_almost_ecam_probe+0x24/0x30
platform_drv_probe+0x50/0xa0
really_probe+0xa0/0x3e0
driver_probe_device+0x58/0x100
device_driver_attach+0x6c/0x90
__driver_attach+0x84/0xc8
bus_for_each_dev+0x74/0xc8
driver_attach+0x20/0x28
bus_add_driver+0x148/0x1f0
driver_register+0x60/0x110
__platform_driver_register+0x40/0x48
hisi_pcie_almost_ecam_driver_init+0x1c/0x24
The specific problem here is that the mbigen driver real probe has failed
as the mbigen_of_create_domain()->of_platform_device_create() call fails,
the reason for that being that we never destroyed the platform device
created during the remove test dry run and there is some conflict.
Since we generally would never want to unbind this driver, and to save
adding a driver tear down path for that, just set the driver
.suppress_bind_attrs member to avoid this possibility.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/1579196323-180137-1-git-send-email-john.garry@huawei.com
The Aspeed SOCs provide some interrupts through the System Control
Unit registers. Add an interrupt controller that provides these
interrupts to the system.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/1579123790-6894-3-git-send-email-eajames@linux.ibm.com
Get rid of the legacy IRQ domain and hardcoded IRQ base, since all the
Ingenic drivers and platform code have been updated to use devicetree.
This also fixes the kernel being flooded with messages like:
irq: interrupt-controller@10001000 didn't like hwirq-0x0 to VIRQ8 mapping (rc=-19)
Fixes: 8bc7464b51 ("irqchip: ingenic: Alloc generic chips from IRQ domain").
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200113163329.34282-2-paul@crapouillou.net
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
"IRQ_TIMER", used in the arch/riscv CSR header file, is a sufficiently
generic macro name that it's used by several source files across the
Linux code base. Some of these other files ultimately include the
arch/riscv CSR include file, causing collisions. Fix by prefixing the
RISC-V csr.h IRQ_ macro names with an RV_ prefix.
Fixes: a4c3733d32 ("riscv: abstract out CSR names for supervisor vs machine mode")
Reported-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
Pull irq updates from Ingo Molnar:
"Most of the IRQ subsystem changes in this cycle were irq-chip driver
updates:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
There's also the series from Frederic Weisbecker that fixes memory
ordering bugs for the irq-work logic, whose primary fix is to turn
work->irq_work.flags into an atomic variable and then convert the
complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a
much simpler atomic_fetch_or() call.
There are also various smaller cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs
pinctrl/msm: Setup GPIO chip in hierarchy
irqchip/qcom-pdc: Add irqchip set/get state calls
irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs
irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask
irqchip/qcom-pdc: Update max PDC interrupts
of/irq: Document properties for wakeup interrupt parent
genirq: Introduce irq_chip_get/set_parent_state calls
irqdomain: Add bus token DOMAIN_BUS_WAKEUP
genirq: Fix function documentation of __irq_alloc_descs()
irq_work: Fix IRQ_WORK_BUSY bit clearing
irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
irq_work: Slightly simplify IRQ_WORK_PENDING clearing
irq_work: Fix irq_work_claim() memory ordering
irq_work: Convert flags to atomic_t
irqchip: Ingenic: Add process for more than one irq at the same time.
irqchip: ingenic: Alloc generic chips from IRQ domain
irqchip: ingenic: Get virq number from IRQ domain
irqchip: ingenic: Error out if IRQ domain creation failed
irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions
...
New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEElRDoIDdEz9/svf2Kx4+xDQu9KksFAl3dkMcACgkQx4+xDQu9
KksoQA/+MZdtMrSe+j5yep7ZO803ivdS5tPCjNI06An2Ps8OJmJKoU8zSCIbygfM
xIQ8R5KVLjd1DTW3SKNrL3bUsH0PdwGHKj69z0gMA01kGBe5CfJEzHw03U4It++t
xaPAYJje99xtdEzZMro/Z+/Gsz/XM5SDZmY4i6quSlHOmL0HP6zftk3jPvxO+XtD
7unQJSHuZElqs984OmR+6DUTiaIlJ4P+/xxlFydswq19/tDNCXpukLhMHkOND3W+
3dBHAp9U18dz2I8lD3xlppVbvgCnud7z+xa+XY1Q/BluoYIEe6714S+9lr8TCdTP
43wL9hSvbDPyaydnmKU7VqwdcWrbVQkA7H3GtxeiUZYvyDdidk9sARqg0n6uoedw
48uRfeI0jCQXh6XdFNMCqNgYPpcpHY3isMKVCi2U6TT0fNdUUC3f62qsOIP0vQXh
4hDys5JzIoBKv8nz/ap+1xzUluBt6FGmySPlTbd8ryn2m2Yd0EsHjywcEGRJMrlM
KcOYgLAKcr9rRF4ap/NqQy74AvC+pOcDVeUHPD0WXYDRQn6L0wbp8YElzRf8W1BC
b7osrRSNLfzC2LsEUEK+qYHrT4+cuWBbkuobAEHMY/OnLW1OKEifZQIdknAE1/yg
n2qy4DuA6qta+Q1GiH8OOt9AEYHPw+SDP3+qFaJK5ZZMb3v565A=
=nbwY
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT
file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv"
* tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (22 commits)
riscv: provide a flat image loader
riscv: add nommu support
riscv: clear the instruction cache and all registers when booting
riscv: read the hart ID from mhartid on boot
riscv: provide native clint access for M-mode
riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00
riscv: add support for MMIO access to the timer registers
riscv: implement remote sfence.i using IPIs
riscv: cleanup the default power off implementation
riscv: poison SBI calls for M-mode
riscv: don't allow selecting SBI based drivers for M-mode
RISC-V: Add multiple compression image format.
riscv: clean up the macro format in each header file
riscv: Use PMD_SIZE to replace PTE_PARENT_SIZE
riscv: abstract out CSR names for supervisor vs machine mode
riscv: separate MMIO functions into their own header file
riscv: enter WFI in default_power_off() if SBI does not shutdown
RISC-V: Issue a tlb page flush if possible
RISC-V: Issue a local tlbflush if possible.
RISC-V: Do not invoke SBI call if cpumask is empty
...
- Data abort report and injection
- Steal time support
- GICv4 performance improvements
- vgic ITS emulation fixes
- Simplify FWB handling
- Enable halt polling counters
- Make the emulated timer PREEMPT_RT compliant
s390:
- Small fixes and cleanups
- selftest improvements
- yield improvements
PPC:
- Add capability to tell userspace whether we can single-step the guest.
- Improve the allocation of XIVE virtual processor IDs
- Rewrite interrupt synthesis code to deliver interrupts in virtual
mode when appropriate.
- Minor cleanups and improvements.
x86:
- XSAVES support for AMD
- more accurate report of nested guest TSC to the nested hypervisor
- retpoline optimizations
- support for nested 5-level page tables
- PMU virtualization optimizations, and improved support for nested
PMU virtualization
- correct latching of INITs for nested virtualization
- IOAPIC optimization
- TSX_CTRL virtualization for more TAA happiness
- improved allocation and flushing of SEV ASIDs
- many bugfixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJd27PMAAoJEL/70l94x66DspsH+gPc6YWtKJFJH58Zj8NrNh6y
t0FwDFcvUa51+m4jaY4L5Y8+zqu1dZFnPPhFGqNWpxrjCEvE/glQJv3BiUX06Seh
aYUHNymGoYCTJOHaaGhV+NlgQaDuZOCOkIsOLAPehyFd1KojwB+FRC0xmO6aROPw
9yQgYrKuK1UUn5HwxBNrMS4+Xv+2iKv/9sTnq1G4W2qX2NZQg84LVPg1zIdkCh3D
3GOvoCBEk3ivQqjmdE7rP/InPr0XvW0b6TFhchIk8J6jEIQFHsmOUefiTvTxsIHV
OKAZwvyeYPrYHA/aDZpaBmY2aR0ydfKDUQcviNIJoF1vOktGs0hvl3VbsmG8QCg=
=OSI1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- data abort report and injection
- steal time support
- GICv4 performance improvements
- vgic ITS emulation fixes
- simplify FWB handling
- enable halt polling counters
- make the emulated timer PREEMPT_RT compliant
s390:
- small fixes and cleanups
- selftest improvements
- yield improvements
PPC:
- add capability to tell userspace whether we can single-step the
guest
- improve the allocation of XIVE virtual processor IDs
- rewrite interrupt synthesis code to deliver interrupts in virtual
mode when appropriate.
- minor cleanups and improvements.
x86:
- XSAVES support for AMD
- more accurate report of nested guest TSC to the nested hypervisor
- retpoline optimizations
- support for nested 5-level page tables
- PMU virtualization optimizations, and improved support for nested
PMU virtualization
- correct latching of INITs for nested virtualization
- IOAPIC optimization
- TSX_CTRL virtualization for more TAA happiness
- improved allocation and flushing of SEV ASIDs
- many bugfixes and cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (127 commits)
kvm: nVMX: Relax guest IA32_FEATURE_CONTROL constraints
KVM: x86: Grab KVM's srcu lock when setting nested state
KVM: x86: Open code shared_msr_update() in its only caller
KVM: Fix jump label out_free_* in kvm_init()
KVM: x86: Remove a spurious export of a static function
KVM: x86: create mmu/ subdirectory
KVM: nVMX: Remove unnecessary TLB flushes on L1<->L2 switches when L1 use apic-access-page
KVM: x86: remove set but not used variable 'called'
KVM: nVMX: Do not mark vmcs02->apic_access_page as dirty when unpinning
KVM: vmx: use MSR_IA32_TSX_CTRL to hard-disable TSX on guest that lack it
KVM: vmx: implement MSR_IA32_TSX_CTRL disable RTM functionality
KVM: x86: implement MSR_IA32_TSX_CTRL effect on CPUID
KVM: x86: do not modify masked bits of shared MSRs
KVM: x86: fix presentation of TSX feature in ARCH_CAPABILITIES
KVM: PPC: Book3S HV: XIVE: Fix potential page leak on error path
KVM: PPC: Book3S HV: XIVE: Free previous EQ page when setting up a new one
KVM: nVMX: Assume TLB entries of L1 and L2 are tagged differently if L0 use EPT
KVM: x86: Unexport kvm_vcpu_reload_apic_access_page()
KVM: nVMX: add CR4_LA57 bit to nested CR4_FIXED1
KVM: nVMX: Use semi-colon instead of comma for exit-handlers initialization
...
- On ARMv8 CPUs without hardware updates of the access flag, avoid
failing cow_user_page() on PFN mappings if the pte is old. The patches
introduce an arch_faults_on_old_pte() macro, defined as false on x86.
When true, cow_user_page() makes the pte young before attempting
__copy_from_user_inatomic().
- Covert the synchronous exception handling paths in
arch/arm64/kernel/entry.S to C.
- FTRACE_WITH_REGS support for arm64.
- ZONE_DMA re-introduced on arm64 to support Raspberry Pi 4
- Several kselftest cases specific to arm64, together with a MAINTAINERS
update for these files (moved to the ARM64 PORT entry).
- Workaround for a Neoverse-N1 erratum where the CPU may fetch stale
instructions under certain conditions.
- Workaround for Cortex-A57 and A72 errata where the CPU may
speculatively execute an AT instruction and associate a VMID with the
wrong guest page tables (corrupting the TLB).
- Perf updates for arm64: additional PMU topologies on HiSilicon
platforms, support for CCN-512 interconnect, AXI ID filtering in the
IMX8 DDR PMU, support for the CCPI2 uncore PMU in ThunderX2.
- GICv3 optimisation to avoid a heavy barrier when accessing the
ICC_PMR_EL1 register.
- ELF HWCAP documentation updates and clean-up.
- SMC calling convention conduit code clean-up.
- KASLR diagnostics printed during boot
- NVIDIA Carmel CPU added to the KPTI whitelist
- Some arm64 mm clean-ups: use generic free_initrd_mem(), remove stale
macro, simplify calculation in __create_pgd_mapping(), typos.
- Kconfig clean-ups: CMDLINE_FORCE to depend on CMDLINE, choice for
endinanness to help with allmodconfig.
-----BEGIN PGP SIGNATURE-----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=TPL9
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Apart from the arm64-specific bits (core arch and perf, new arm64
selftests), it touches the generic cow_user_page() (reviewed by
Kirill) together with a macro for x86 to preserve the existing
behaviour on this architecture.
Summary:
- On ARMv8 CPUs without hardware updates of the access flag, avoid
failing cow_user_page() on PFN mappings if the pte is old. The
patches introduce an arch_faults_on_old_pte() macro, defined as
false on x86. When true, cow_user_page() makes the pte young before
attempting __copy_from_user_inatomic().
- Covert the synchronous exception handling paths in
arch/arm64/kernel/entry.S to C.
- FTRACE_WITH_REGS support for arm64.
- ZONE_DMA re-introduced on arm64 to support Raspberry Pi 4
- Several kselftest cases specific to arm64, together with a
MAINTAINERS update for these files (moved to the ARM64 PORT entry).
- Workaround for a Neoverse-N1 erratum where the CPU may fetch stale
instructions under certain conditions.
- Workaround for Cortex-A57 and A72 errata where the CPU may
speculatively execute an AT instruction and associate a VMID with
the wrong guest page tables (corrupting the TLB).
- Perf updates for arm64: additional PMU topologies on HiSilicon
platforms, support for CCN-512 interconnect, AXI ID filtering in
the IMX8 DDR PMU, support for the CCPI2 uncore PMU in ThunderX2.
- GICv3 optimisation to avoid a heavy barrier when accessing the
ICC_PMR_EL1 register.
- ELF HWCAP documentation updates and clean-up.
- SMC calling convention conduit code clean-up.
- KASLR diagnostics printed during boot
- NVIDIA Carmel CPU added to the KPTI whitelist
- Some arm64 mm clean-ups: use generic free_initrd_mem(), remove
stale macro, simplify calculation in __create_pgd_mapping(), typos.
- Kconfig clean-ups: CMDLINE_FORCE to depend on CMDLINE, choice for
endinanness to help with allmodconfig"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (93 commits)
arm64: Kconfig: add a choice for endianness
kselftest: arm64: fix spelling mistake "contiguos" -> "contiguous"
arm64: Kconfig: make CMDLINE_FORCE depend on CMDLINE
MAINTAINERS: Add arm64 selftests to the ARM64 PORT entry
arm64: kaslr: Check command line before looking for a seed
arm64: kaslr: Announce KASLR status on boot
kselftest: arm64: fake_sigreturn_misaligned_sp
kselftest: arm64: fake_sigreturn_bad_size
kselftest: arm64: fake_sigreturn_duplicated_fpsimd
kselftest: arm64: fake_sigreturn_missing_fpsimd
kselftest: arm64: fake_sigreturn_bad_size_for_magic0
kselftest: arm64: fake_sigreturn_bad_magic
kselftest: arm64: add helper get_current_context
kselftest: arm64: extend test_init functionalities
kselftest: arm64: mangle_pstate_invalid_mode_el[123][ht]
kselftest: arm64: mangle_pstate_invalid_daif_bits
kselftest: arm64: mangle_pstate_invalid_compat_toggle and common utils
kselftest: arm64: extend toplevel skeleton Makefile
drivers/perf: hisi: update the sccl_id/ccl_id for certain HiSilicon platform
arm64: mm: reserve CMA and crashkernel in ZONE_DMA32
...
Remove <linux/pci.h> and <linux/msi.h> from being included directly as part
of the include/linux/of_pci.h, and remove superfluous declaration of struct
of_phandle_args.
Move users of include <linux/of_pci.h> to include <linux/pci.h> and
<linux/msi.h> directly rather than rely on both being included transitively
through <linux/of_pci.h>.
Link: https://lore.kernel.org/r/20190903113059.2901-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
- Allow non-ISV data aborts to be reported to userspace
- Allow injection of data aborts from userspace
- Expose stolen time to guests
- GICv4 performance improvements
- vgic ITS emulation fixes
- Simplify FWB handling
- Enable halt pool counters
- Make the emulated timer PREEMPT_RT compliant
-----BEGIN PGP SIGNATURE-----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=SxBH
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm updates for Linux 5.5:
- Allow non-ISV data aborts to be reported to userspace
- Allow injection of data aborts from userspace
- Expose stolen time to guests
- GICv4 performance improvements
- vgic ITS emulation fixes
- Simplify FWB handling
- Enable halt pool counters
- Make the emulated timer PREEMPT_RT compliant
Conflicts:
include/uapi/linux/kvm.h
Add irqchip calls to set/get interrupt state from the parent interrupt
controller. When GPIOs are renabled as interrupt lines, it is desirable
to clear the interrupt state at the GIC. This avoids any unwanted
interrupt as a result of stale pending state recorded when the line was
used as a GPIO.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
[Lina: updated commit text, rearranged code]
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-8-git-send-email-ilina@codeaurora.org
Introduce a new domain for wakeup capable GPIOs. The domain can be
requested using the bus token DOMAIN_BUS_WAKEUP. In the following
patches, we will specify PDC as the wakeup-parent for the TLMM GPIO
irqchip. Requesting a wakeup GPIO will setup the GPIO and the
corresponding PDC interrupt as its parent.
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-5-git-send-email-ilina@codeaurora.org
When an interrupt is to be serviced, the convention is to mask the
interrupt at the chip and unmask after servicing the interrupt. Enabling
and disabling the interrupt at the PDC irqchip causes an interrupt storm
due to the way dual edge interrupts are handled in hardware.
Skip configuring the PDC when the IRQ is masked and unmasked, instead
use the irq_enable/irq_disable callbacks to toggle the IRQ_ENABLE
register at the PDC. The PDC's IRQ_ENABLE register is only used during
the monitoring mode when the system is asleep and is not needed for
active mode detection.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-4-git-send-email-ilina@codeaurora.org
Newer SoCs have increased the number of interrupts routed to the PDC
interrupt controller. Update the definition of max PDC interrupts.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-3-git-send-email-ilina@codeaurora.org
A coccicheck run provided information like the following.
drivers/irqchip/irq-ti-sci-inta.c:250:9-16: WARNING: ERR_CAST can be used
with vint_desc.
Generated by: scripts/coccinelle/api/err_cast.cocci
Thus adjust the exception handling in one if branch.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/776b7135-26af-df7d-c3a9-4339f7bf1f15@web.de
Add process for the situation that more than one irq is coming to
a single chip at the same time. The original code will only respond
to the lowest setted bit in JZ_REG_INTC_PENDING, and then exit the
interrupt dispatch function. After exiting the interrupt dispatch
function, since the second interrupt has not yet responded, the
interrupt dispatch function is again entered to process the second
interrupt. This creates additional unnecessary overhead, and the
more interrupts that occur at the same time, the more overhead is
added. The improved method in this patch is to check whether there
are still unresponsive interrupts after processing the lowest
setted bit interrupt. If there are any, the processing will be
processed according to the bit in JZ_REG_INTC_PENDING, and the
interrupt dispatch function will be exited until all processing
is completed.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/1570015525-27018-6-git-send-email-zhouyanjie@zoho.com
The VLPI map is currently a mutex, and that's a bad idea as
this lock can be taken in non-preemptible contexts. Convert
it to a raw spinlock, and turn the memory allocation of the
VLPI map to be atomic.
Reported-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191108165805.3071-12-maz@kernel.org
Obtaining the mapping ivformation for a VLPI should always be
done with the vlpi_lock for this device held. Otherwise, we
expose ourselves to races against a concurrent unmap.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191108165805.3071-11-maz@kernel.org
We have so far always injected/cleared VLPIs using either
INT+SYNC or CLEAR+SYNC sequences, but that's pretty wrong
for two reasons:
- SYNC only synchronises physical LPIs
- The collection ID that for the associated LPI doesn't match
the redistributor the vPE is associated with
Instead, send an {INT,CLEAR}+VSYNC for forwarded LPIs, ensuring
that the ITS synchronises against the virtual pending table.
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191108165805.3071-10-maz@kernel.org
We have so far alwways invalidated VLPIs usinc an INV+SYNC
sequence, but that's pretty wrong for two reasons:
- SYNC only synchronises physical LPIs
- The collection ID that for the associated LPI doesn't match
the redistributor the vPE is associated with
Instead, send an INV+VSYNC for forwarded LPIs, ensuring that
the ITS can properly synchronise the invalidation of VLPIs.
Fixes: 015ec0386a ("irqchip/gic-v3-its: Add VLPI configuration handling")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191108165805.3071-9-maz@kernel.org
We allocate the collection mapping on device creation, but somehow
free it on the irqdomain free path, which is pretty inconsistent
and has led to bugs in the past.
Move it to the point where we teardown the device, making the
alloc/free symetric.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191108165805.3071-2-maz@kernel.org
Remove the sdm845 SoC specific compatible to make the driver
easily reusable across other SoC's with the same IP block.
This will reduce further churn adding any SoC specific
compatibles unless really needed.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191108092824.9773-7-rnayak@codeaurora.org
The LS1021A allows inverting the polarity of six interrupt lines
IRQ[0:5] via the scfg_intpcr register, effectively allowing
IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_EDGE_FALLING for those. We just need to
check the type, set the relevant bit in INTPCR accordingly, and fixup
the type argument before calling the GIC's irq_set_type.
In fact, the power-on-reset value of the INTPCR register on the LS1021A
is so that all six lines have their polarity inverted. Hence any
hardware connected to those lines is unusable without this: If the line
is indeed active low, the generic GIC code will reject an irq spec with
IRQ_TYPE_LEVEL_LOW, while if the line is active high, we must obviously
disable the polarity inversion (writing 0 to the relevant bit) before
unmasking the interrupt.
Some other Layerscape SOCs (LS1043A, LS1046A) have a similar feature,
just with a different number of external interrupt lines (and a
different POR value for the INTPCR register). This driver should be
prepared for supporting those by properly filling out the device tree
node. I have the reference manuals for all three boards, but I've only
tested the driver on an LS1021A.
Unfortunately, the Kconfig symbol ARCH_LAYERSCAPE only exists on
arm64, so do as is done for irq-ls-scfg-msi.c: introduce a new symbol
which is set when either ARCH_LAYERSCAPE or SOC_LS1021A is set.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191107122115.6244-3-linux@rasmusvillemoes.dk
On some specific chips like 7211 we need to leave some interrupts
untouched/forwarded to the VPU which is another agent in the system
making use of that interrupt controller hardware (goes to both ARM GIC
and VPU L1 interrupt controller). Make that possible by using the
existing brcm,int-fwd-mask property and take necessary actions to avoid
masking that interrupt as well as not allowing Linux to map them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-6-f.fainelli@gmail.com
If the 'brcm,irq-can-wake' property is specified, make sure we also
enable the corresponding parent interrupt we are attached to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-4-f.fainelli@gmail.com
The current L1 controller does not mask any interrupts when dropping
into suspend. This mean we can receive unexpected wake up sources.
Modified the BCM7038 L1 controller to mask the all non-wake interrupts
before dropping into suspend.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-2-f.fainelli@gmail.com
The its_cmd_block struct can either have u64 or __le64
data in it, so make a anonymous union to remove the
sparse warnings when converting to/from these.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191017112955.15853-1-ben.dooks@codethink.co.uk
Many of the privileged CSRs exist in a supervisor and machine version
that are used very similarly. Provide versions of the CSR names and
fields that map to either the S-mode or M-mode variant depending on
a new CONFIG_RISCV_M_MODE kconfig symbol.
Contains contributions from Damien Le Moal <Damien.LeMoal@wdc.com>
and Paul Walmsley <paul.walmsley@sifive.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de> # for drivers/clocksource, drivers/irqchip
[paul.walmsley@sifive.com: updated to apply]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When the VHE code was reworked, a lot of the vgic stuff was moved around,
but the GICv4 residency code did stay untouched, meaning that we come
in and out of residency on each flush/sync, which is obviously suboptimal.
To address this, let's move things around a bit:
- Residency entry (flush) moves to vcpu_load
- Residency exit (sync) moves to vcpu_put
- On blocking (entry to WFI), we "put"
- On unblocking (exit from WFI), we "load"
Because these can nest (load/block/put/load/unblock/put, for example),
we now have per-VPE tracking of the residency state.
Additionally, vgic_v4_put gains a "need doorbell" parameter, which only
gets set to true when blocking because of a WFI. This allows a finer
control of the doorbell, which now also gets disabled as soon as
it gets signaled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191027144234.8395-2-maz@kernel.org
- Sifive PLIC: force driver to skip non-relevant contexts
- GICv4: Don't send VMOVP commands to ITSs that don't have
this vPE mapped
-----BEGIN PGP SIGNATURE-----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=9wMN
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull the second lot of irqchip updates for 5.4 from Marc Zyngier:
- Sifive PLIC: force driver to skip non-relevant contexts
- GICv4: Don't send VMOVP commands to ITSs that don't have
this vPE mapped
Modify plic_init() to skip .dts interrupt contexts other
than supervisor external interrupt.
The .dts entry for plic may specify multiple interrupt contexts.
For example, it may assign two entries IRQ_M_EXT and IRQ_S_EXT,
in that order, to the same interrupt controller. This patch
modifies plic_init() to skip the IRQ_M_EXT context since
IRQ_S_EXT is currently the only supported context.
If IRQ_M_EXT is not skipped, plic_init() will report "handler
already present for context" when it comes across the IRQ_S_EXT
context in the next iteration of its loop.
Without this patch, .dts would have to be edited to replace the
value of IRQ_M_EXT with -1 for it to be skipped.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # arch/riscv
Link: https://lkml.kernel.org/r/1571933503-21504-1-git-send-email-alan.mikhak@sifive.com
On a system without Single VMOVP support (say GITS_TYPER.VMOVP == 0),
we will map vPEs only on ITSs that will actually control interrupts
for the given VM. And when moving a vPE, the VMOVP command will be
issued only for those ITSs.
But when issuing VMOVPs we seemed fail to present the exact ITSList
to ITSs who are actually included in the synchronization operation.
The its_list_map we're currently using includes all ITSs in the system,
even though some of them don't have the corresponding vPE mapping at all.
Introduce get_its_list() to get the per-VM its_list_map, to indicate
which ITSs have vPE mappings for the given VM, and use this map as
the expected ITSList when building VMOVP. This is hopefully a performance
gain not to do some synchronization with those unsuspecting ITSs.
And initialize the whole command descriptor to zero at beginning, since
the seq_num and its_list should be RES0 when GITS_TYPER.VMOVP == 1.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1571802386-2680-1-git-send-email-yuzenghui@huawei.com
The GICv3 architecture specification is incredibly misleading when it
comes to PMR and the requirement for a DSB. It turns out that this DSB
is only required if the CPU interface sends an Upstream Control
message to the redistributor in order to update the RD's view of PMR.
This message is only sent when ICC_CTLR_EL1.PMHE is set, which isn't
the case in Linux. It can still be set from EL3, so some special care
is required. But the upshot is that in the (hopefuly large) majority
of the cases, we can drop the DSB altogether.
This relies on a new static key being set if the boot CPU has PMHE
set. The drawback is that this static key has to be exported to
modules.
Cc: Will Deacon <will@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Add retrigger support to Amazon's al-fic driver
- Add SAM9X60 support to Atmel's AIC5 irqchip
- Fix GICv3 maximum interrupt calculation
- Convert SiFive's PLIC to the fasteoi IRQ flow
-----BEGIN PGP SIGNATURE-----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=AV7P
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Add retrigger support to Amazon's al-fic driver
- Add SAM9X60 support to Atmel's AIC5 irqchip
- Fix GICv3 maximum interrupt calculation
- Convert SiFive's PLIC to the fasteoi IRQ flow
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
The SiFive PLIC interrupt controller seems to have all the HW
features to support the fasteoi flow, but the driver seems to be
stuck in a distant past. Bring it into the 21st century.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Palmer Dabbelt <palmer@sifive.com> (QEMU Boot)
Tested-by: Darius Rad <darius@bluespec.com> (on 2 HW PLIC implementations)
Tested-by: Paul Walmsley <paul.walmsley@sifive.com> (HiFive Unleashed)
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/8636gxskmj.wl-maz@kernel.org
As per GIC spec, ITLinesNumber indicates the maximum SPI INTID that
the GIC implementation supports. And the maximum SPI INTID an
implementation might support is 1019 (field value 11111).
max(GICD_TYPER_SPIS(...), 1020) is not what we actually want for
GIC_LINE_NR. Fix it to min(GICD_TYPER_SPIS(...), 1020).
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1568789850-14080-1-git-send-email-yuzenghui@huawei.com
Pull core irq updates from Thomas Gleixner:
"Updates from the irq departement:
- Update the interrupt spreading code so it handles numa node with
different CPU counts properly.
- A large overhaul of the ARM GiCv3 driver to support new PPI and SPI
ranges.
- Conversion of all alloc_fwnode() users to use physical addresses
instead of virtual addresses so the virtual addresses are not
leaked. The physical address is sufficient to identify the
associated interrupt chip.
- Add support for Marvel MMP3, Amlogic Meson SM1 interrupt chips.
- Enforce interrupt threading at compile time if RT is enabled.
- Small updates and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
irqchip/gic-v3-its: Fix LPI release for Multi-MSI devices
irqchip/uniphier-aidet: Use devm_platform_ioremap_resource()
irqdomain: Add the missing assignment of domain->fwnode for named fwnode
irqchip/mmp: Coexist with GIC root IRQ controller
irqchip/mmp: Mask off interrupts from other cores
irqchip/mmp: Add missing chained_irq_{enter,exit}()
irqchip/mmp: Do not use of_address_to_resource() to get mux regs
irqchip/meson-gpio: Add support for meson sm1 SoCs
dt-bindings: interrupt-controller: New binding for the meson sm1 SoCs
genirq/affinity: Remove const qualifier from node_to_cpumask argument
genirq/affinity: Spread vectors on node according to nr_cpu ratio
genirq/affinity: Improve __irq_build_affinity_masks()
irqchip: Remove dev_err() usage after platform_get_irq()
irqchip: Add include guard to irq-partition-percpu.h
irqchip/mmp: Do not call irq_set_default_host() on DT platforms
irqchip/gic-v3-its: Remove the redundant set_bit for lpi_map
irqchip/gic-v3: Add quirks for HIP06/07 invalid GICD_TYPER erratum 161010803
irqchip/gic: Skip DT quirks when evaluating IIDR-based quirks
irqchip/gic-v3: Warn about inconsistent implementations of extended ranges
irqchip/gic-v3: Add EPPI range support
...
When allocating a range of LPIs for a Multi-MSI capable device,
this allocation extended to the closest power of 2.
But on the release path, the interrupts are released one by
one. This results in not releasing the "extra" range, leaking
the its_device. Trying to reprobe the device will then fail.
Fix it by releasing the LPIs the same way we allocate them.
Fixes: 8208d1708b ("irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size")
Reported-by: Jiaxing Luo <luojiaxing@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/f5e948aa-e32f-3f74-ae30-31fee06c2a74@huawei.com
When running in M-mode, the S-mode plic handlers are still listed in the
device tree. Ignore them by setting the maximum threshold.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Replace the chain of platform_get_resource() and devm_ioremap_resource()
with devm_platform_ioremap_resource().
This allows to remove the local variable for (struct resource *), and
have one function call less.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190905034932.12587-1-yamada.masahiro@socionext.com
On MMP3, the GIC can be set as a root IRQ interrupt controller. If the
device tree indicated that GIC is enabled, avoid hooking up
mmp2_handle_irq().
The interrupt muxes are still being used.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-10-lkundrak@v3.sk
On mmp3, there's an extra set of ICU registers (ICU2) that handle
interrupts on the extra cores. When masking off interrupts on MP1,
these should be masked as well.
We add a new interrupt controller via device tree to identify when we're
looking at an mmp3 machine via compatible field of "marvell,mmp3-intc".
[lkundrak@v3.sk: Changed "mrvl,mmp3-intc" compatible strings to
"marvell,mmp3-intc". Tidied up the subject line a bit.]
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-9-lkundrak@v3.sk
--
Changes since v1:
- Moved mmp3-specific mmp_icu2_base initialization from mmp_init_bases() to
mmp3_of_init() so that we don't have to check for marvell,mmp3-intc
compatibility twice.
- Drop an superfluous call to irq_set_default_host()
arch/arm/mach-mmp/regs-icu.h | 3 +++
drivers/irqchip/irq-mmp.c | 48 ++++++++++++++++++++++++++++++++++++
2 files changed, 51 insertions(+)
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-9-lkundrak@v3.sk
The lack of chained_irq_exit() leaves the muxed interrupt masked on MMP3.
For reasons unknown this is not a problem on MMP2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-8-lkundrak@v3.sk
The "regs" property of the "mrvl,mmp2-mux-intc" devices are silly. They
are offsets from intc's base, not addresses on the parent bus. At this
point it probably can't be fixed.
On an OLPC XO-1.75 machine, the muxes are children of the intc, not the
axi bus, and thus of_address_to_resource() won't work. We should treat
the values as mere integers as opposed to bus addresses.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20190822092643.593488-7-lkundrak@v3.sk
The meson sm1 SoCs uses the same type of GPIO interrupt controller IP
block as the other meson SoCs, A total of 100 pins can be spied on:
- 223:100 undefined (no interrupt)
- 99:97 3 pins on bank GPIOE
- 96:77 20 pins on bank GPIOX
- 76:61 16 pins on bank GPIOA
- 60:53 8 pins on bank GPIOC
- 52:37 16 pins on bank BOOT
- 36:28 9 pins on bank GPIOH
- 27:12 16 pins on bank GPIOZ
- 11:0 12 pins in the AO domain
Mapping is the same as the g12a family but the sm1 controller
allows to trig an irq on both edges of the input signal. This was
not possible with the previous SoCs families
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20190829161635.25067-3-jbrunet@baylibre.com
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Using a default domain on DT platforms is unnecessary, as the firmware
tables describe the full topology, and nothing is implicit.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
[maz: wrote an actual changelog]
Signed-off-by: Marc Zyngier <maz@kernel.org>
We try to find a free LPI region in device's lpi_map and allocate them
(set them to 1) when we want to allocate LPIs for this device. This is
what bitmap_find_free_region() has done for us. The following set_bit
is redundant and a bit confusing (since we only set_bit against the first
allocated LPI idx). Remove it, and make the set_bit explicit by comment.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
It looks like the HIP06/07 SoCs have extra bits in their GICD_TYPER
registers, which confuse the GICv3.1 code (these systems appear to
expose ESPIs while they actually don't).
Detect these systems as early as possible and wipe the fields that
should be RES0 in the register.
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When evaluating potential quirks matched by reads of the IIDR
register, skip the quirk entries that use a "compatible"
property attached to them, as these are DT based.
Signed-off-by: Marc Zyngier <maz@kernel.org>
As is it usual for the GIC, it isn't disallowed to put together a system
that is majorly inconsistent, with a distributor supporting the
extended ranges while some of the CPUs don't.
Kindly tell the user that things are sailing isn't going to be smooth.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Expand the pre-existing PPI support to be able to deal with the
Extended PPI range (EPPI). This includes obtaining the number of PPIs
from each individual redistributor, and compute the minimum set
(just in case someone builds something really clever...).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Again, PPIs are becoming a variable set. Let's hack the PPI partition
code to make the top-level array dynamically allocated.
Signed-off-by: Marc Zyngier <maz@kernel.org>
As we're about to have a variable number of PPIs, let's make the
allocation of the NMI refcounts dynamic. Also apply some minor
cleanups (moving things around).
Signed-off-by: Marc Zyngier <maz@kernel.org>
GICv3.1 allows up to 80 PPIs (16 legaci PPIs and 64 Extended PPIs),
meaning we can't just leave the old 16 hardcoded everywhere.
We also need to add the infrastructure to discover the number of PPIs
on a per redistributor basis, although we still pretend there is only
16 of them for now.
No functional change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add the required support for the ESPI range, which behave exactly like
the SPIs of old, only with new funky INTIDs.
Signed-off-by: Marc Zyngier <maz@kernel.org>
In the beginning, life was simple. The GIC driver mostly cared about
PPIs, SPIs and LPIs, all with nicely layed out ranges.
We're about to change all that, with new ranges such as EPPI and ESPI
interleaved in the middle of the no-irq-land between the "special IDs"
and the LPI range. Boo.
In order to make our life less hellish, let's introduce a set of primitives
that will allow ranges to be identified easily and offsets to be remapped.
So far, there is no functionnal change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
gic_configure_irq is currently passed the (re)distributor address,
to which it applies an a fixed offset to get to the configuration
registers. This offset is constant across all GICs, or rather it was
until to v3.1...
An easy way out is for the individual drivers to pass the base
address of the configuration register for the considered interrupt.
At the same time, move part of the error handling back to the
individual drivers, as things are about to change on that front.
Signed-off-by: Marc Zyngier <maz@kernel.org>
While do COMPILE_TEST building, if GENERIC_IRQ_CHIP is
not selected, it fails:
drivers/irqchip/irq-ingenic-tcu.o: In function `ingenic_tcu_intc_cascade':
irq-ingenic-tcu.c:(.text+0x13f): undefined reference to `irq_get_domain_generic_chip'
drivers/irqchip/irq-ingenic-tcu.o: In function `ingenic_tcu_irq_init':
irq-ingenic-tcu.c:(.init.text+0x97): undefined reference to `irq_generic_chip_ops'
irq-ingenic-tcu.c:(.init.text+0xdd): undefined reference to `__irq_alloc_domain_generic_chips'
irq-ingenic-tcu.c:(.init.text+0x10b): undefined reference to `irq_get_domain_generic_chip'
select GENERIC_IRQ_CHIP to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 9536eba03e ("irqchip: Add irq-ingenic-tcu driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: <jason@lakedaemon.net>
Cc: <maz@kernel.org>
Cc: <paul@crapouillou.net>
Cc: <malat@debian.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-clk@vger.kernel.org>
This driver handles the interrupt controller built in the Timer/Counter
Unit (TCU) of the JZ47xx SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
Do not expose the base VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the frame's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the distributor's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the ITS' VA (it appears in debugfs). Instead, record
the PA, which at least can be used to precisely identify the associated
irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the distributor's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- Fix a couple of UAF on error paths (RZA1, GICv3 ITS)
- Fix iMX GPCv2 trigger setting
- Add missing of_node_put on error path in MBIGEN
- Add another bunch of /* fall-through */ to silence warnings
-----BEGIN PGP SIGNATURE-----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=oXHS
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
A small bunch of fixes from the irqchip department:
- Fix a couple of UAF on error paths (RZA1, GICv3 ITS)
- Fix iMX GPCv2 trigger setting
- Add missing of_node_put on error path in MBIGEN
- Add another bunch of /* fall-through */ to silence warnings
The gic_node is still being used in the rza1_irqc_parse_map() call
after the of_node_put() call, which may result in use-after-free.
Fixes: a644ccb819 ("irqchip: Add Renesas RZ/A1 Interrupt Controller driver")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The GPCv2 is a stacked IRQ controller below the ARM GIC. It doesn't
care about the IRQ type itself, but needs to forward the type to the
parent IRQ controller, so this one can be configured correctly.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but
in the case of a return from the middle of the loop, there is no put,
thus causing a memory leak. Add an of_node_put before the return in
three places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
In its_vpe_init, when its_alloc_vpe_table fails, we should free
vpt_page allocated just before, instead of vpe->vpt_page.
Let's fix it.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When fall-through warnings was enabled by default the following warning
was starting to show up:
In file included from ../arch/arm64/include/asm/cputype.h:132,
from ../arch/arm64/include/asm/cache.h:8,
from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:15,
from ../include/linux/list.h:9,
from ../include/linux/kobject.h:19,
from ../include/linux/of.h:17,
from ../include/linux/irqdomain.h:35,
from ../include/linux/acpi.h:13,
from ../drivers/irqchip/irq-gic-v3.c:9:
../drivers/irqchip/irq-gic-v3.c: In function ‘gic_cpu_sys_reg_init’:
../arch/arm64/include/asm/sysreg.h:853:2: warning: this statement may fall
through [-Wimplicit-fallthrough=]
asm volatile(__msr_s(r, "%x0") : : "rZ" (__val)); \
^~~
../arch/arm64/include/asm/arch_gicv3.h:20:29: note: in expansion of macro ‘write_sysreg_s’
#define write_gicreg(v, r) write_sysreg_s(v, SYS_ ## r)
^~~~~~~~~~~~~~
../drivers/irqchip/irq-gic-v3.c:773:4: note: in expansion of macro ‘write_gicreg’
write_gicreg(0, ICC_AP0R2_EL1);
^~~~~~~~~~~~
../drivers/irqchip/irq-gic-v3.c:774:3: note: here
case 6:
^~~~
Rework so that the compiler doesn't warn about fall-through.
Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The gic_node is still being used in the rza1_irqc_parse_map() call
after the of_node_put() call, which may result in use-after-free.
Fixes: a644ccb819 ("irqchip: Add Renesas RZ/A1 Interrupt Controller driver")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lkml.kernel.org/r/1562566745-7447-3-git-send-email-wen.yang99@zte.com.cn
Pull irq updates from Thomas Gleixner:
"The irq departement provides the usual mixed bag:
Core:
- Further improvements to the irq timings code which aims to predict
the next interrupt for power state selection to achieve better
latency/power balance
- Add interrupt statistics to the core NMI handlers
- The usual small fixes and cleanups
Drivers:
- Support for Renesas RZ/A1, Annapurna Labs FIC, Meson-G12A SoC and
Amazon Gravition AMR/GIC interrupt controllers.
- Rework of the Renesas INTC controller driver
- ACPI support for Socionext SoCs
- Enhancements to the CSKY interrupt controller
- The usual small fixes and cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
irq/irqdomain: Fix comment typo
genirq: Update irq stats from NMI handlers
irqchip/gic-pm: Remove PM_CLK dependency
irqchip/al-fic: Introduce Amazon's Annapurna Labs Fabric Interrupt Controller Driver
dt-bindings: interrupt-controller: Add Amazon's Annapurna Labs FIC
softirq: Use __this_cpu_write() in takeover_tasklets()
irqchip/mbigen: Stop printing kernel addresses
irqchip/gic: Add dependency for ARM_GIC_MAX_NR
genirq/affinity: Remove unused argument from [__]irq_build_affinity_masks()
genirq/timings: Add selftest for next event computation
genirq/timings: Add selftest for irqs circular buffer
genirq/timings: Add selftest for circular array
genirq/timings: Encapsulate storing function
genirq/timings: Encapsulate timings push
genirq/timings: Optimize the period detection speed
genirq/timings: Fix timings buffer inspection
genirq/timings: Fix next event index function
irqchip/qcom: Use struct_size() in devm_kzalloc()
irqchip/irq-csky-mpintc: Remove unnecessary loop in interrupt handler
dt-bindings: interrupt-controller: Update csky mpintc
...
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new XAFLAG
and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the 'arm_boot_flags'
introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE5RElWfyWxS+3PLO2a9axLQDIXvEFAl0eHqcACgkQa9axLQDI
XvFyNA/+L+bnkz8m3ncydlqqfXomQn4eJJVQ8Uksb0knJz+1+3CUxxbO4ry4jXZN
fMkbggYrDPRKpDbsUl0lsRipj7jW9bqan+N37c3SWqCkgb6HqDaHViwxdx6Ec/Uk
gHudozDSPh/8c7hxGcSyt/CFyuW6b+8eYIQU5rtIgz8aVY2BypBvS/7YtYCbIkx0
w4CFleRTK1zXD5mJQhrc6jyDx659sVkrAvdhf6YIymOY8nBTv40vwdNo3beJMYp8
Po/+0Ixu+VkHUNtmYYZQgP/AGH96xiTcRnUqd172JdtRPpCLqnLqwFokXeVIlUKT
KZFMDPzK+756Ayn4z4huEePPAOGlHbJje8JVNnFyreKhVVcCotW7YPY/oJR10bnc
eo7yD+DxABTn+93G2yP436bNVa8qO1UqjOBfInWBtnNFJfANIkZweij/MQ6MjaTA
o7KtviHnZFClefMPoiI7HDzwL8XSmsBDbeQ04s2Wxku1Y2xUHLx4iLmadwLQ1ZPb
lZMTZP3N/T1554MoURVA1afCjAwiqU3bt1xDUGjbBVjLfSPBAn/25IacsG9Li9AF
7Rp1M9VhrfLftjFFkB2HwpbhRASOxaOSx+EI3kzEfCtM2O9I1WHgP3rvCdc3l0HU
tbK0/IggQicNgz7GSZ8xDlWPwwSadXYGLys+xlMZEYd3pDIOiFc=
=0TDT
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new
XAFLAG and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the
'arm_boot_flags' introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
perf: arm_spe: Enable ACPI/Platform automatic module loading
arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
ACPI/PPTT: Modify node flag detection to find last IDENTICAL
x86/entry: Simplify _TIF_SYSCALL_EMU handling
arm64: rename dump_instr as dump_kernel_instr
arm64/mm: Drop [PTE|PMD]_TYPE_FAULT
arm64: Implement panic_smp_self_stop()
arm64: Improve parking of stopped CPUs
arm64: Expose FRINT capabilities to userspace
arm64: Expose ARMv8.5 CondM capability to userspace
arm64: defconfig: enable CONFIG_RANDOMIZE_BASE
arm64: ARM64_MODULES_PLTS must depend on MODULES
arm64: bpf: do not allocate executable memory
arm64/kprobes: set VM_FLUSH_RESET_PERMS on kprobe instruction pages
arm64/mm: wire up CONFIG_ARCH_HAS_SET_DIRECT_MAP
arm64: module: create module allocations without exec permissions
arm64: Allow user selection of ARM64_MODULE_PLTS
acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
arm64: Allow selecting Pseudo-NMI again
...
gic-pm driver does not use pm-clk interface now and hence the dependency
is removed from Kconfig.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Amazon's Annapurna Labs Fabric Interrupt Controller has 32 inputs.
A FIC (Fabric Interrupt Controller) may be cascaded into another FIC or
directly to the main CPU Interrupt Controller (e.g. GIC).
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull irq fixes from Ingo Molnar:
"Diverse irqchip driver fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix command queue pointer comparison bug
irqchip/mips-gic: Use the correct local interrupt map registers
irqchip/ti-sci-inta: Fix kernel crash if irq_create_fwspec_mapping fail
irqchip/irq-csky-mpintc: Support auto irq deliver to all cpus
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
In the presence of any form of instrumentation, nmi_enter() should be
done before calling any traceable code and any instrumentation code.
Currently, nmi_enter() is done in handle_domain_nmi(), which is much
too late as instrumentation code might get called before. Move the
nmi_enter/exit() calls to the arch IRQ vector handler.
On arm64, it is not possible to know if the IRQ vector handler was
called because of an NMI before acknowledging the interrupt. However, It
is possible to know whether normal interrupts could be taken in the
interrupted context (i.e. if taking an NMI in that context could
introduce a potential race condition).
When interrupting a context with IRQs disabled, call nmi_enter() as soon
as possible. In contexts with IRQs enabled, defer this to the interrupt
controller, which is in a better position to know if an interrupt taken
is an NMI.
Fixes: bc3c03ccb4 ("arm64: Enable the support of pseudo-NMIs")
Cc: <stable@vger.kernel.org> # 5.1.x-
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses the full gnu general public license is included in this
distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081202.258730266@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kbuild complains about ixp4xx_irq_setup not being __init
itself in some configurations:
WARNING: vmlinux.o(.text+0x85bae4): Section mismatch in reference from the function ixp4xx_irq_setup() to the function .init.text:set_handle_irq()
The function ixp4xx_irq_setup() references
the function __init set_handle_irq().
This is often because ixp4xx_irq_setup lacks a __init
annotation or the annotation of set_handle_irq is wrong.
I suspect it normally gets inlined, so we get no such warning,
but clang makes this obvious when the function is left out
of line.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
After commit ad67b74d24 ("printk: hash addresses printed with %p"),
it will print "____ptrval____" instead of actual addresses when mbigen
create domain fails,
Hisilicon MBIGEN-V2 HISI0152:00: Failed to create mbi-gen@(____ptrval____) irqdomain
Hisilicon MBIGEN-V2: probe of HISI0152:00 failed with error -12
dev_xxx() helper contains the device info, HISI0152:00, which stands for
mbigen ACPI HID and its UID, we can identify the failing probed mbigen,
so just remove the printing "mgn_chip->base", and also add missing "\n".
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
CONFIG_ARM_GIC_MAX_NR is enabled by default.
It is redundant in x86 and IA-64 where is
without GIC.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = devm_kzalloc(dev, size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable alloc_sz is not necessary, hence it
is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
csky_mpintc_handler()
->handle_domain_irq()
->irq_exit()
->invoke_softirq()
->__do_softirq()
->local_irq_enable()
If new interrupt coming, it'll get into interrupt trap before return to
csky_mpintc_handler(). So there is no need loop in csky_mpintc_handler.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Support 4 triger types:
- IRQ_TYPE_LEVEL_HIGH
- IRQ_TYPE_LEVEL_LOW
- IRQ_TYPE_EDGE_RISING
- IRQ_TYPE_EDGE_FALLING
All of above could be set in DeviceTree file and it still compatible
with the old DeviceTree format.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_chip .name field should contain the device's class (not
instance) name, while .parent_device should point to the device itself.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_chip .name field should contain the device's class (not
instance) name, while .parent_device should point to the device itself.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Meson-G12A SoC uses the same GPIO interrupt controller IP block as the
other Meson SoCs, A totle of 100 pins can be spied on, which is the sum of:
- 223:100 undefined (no interrupt)
- 99:97 3 pins on bank GPIOE
- 96:77 20 pins on bank GPIOX
- 76:61 16 pins on bank GPIOA
- 60:53 8 pins on bank GPIOC
- 52:37 16 pins on bank BOOT
- 36:28 9 pins on bank GPIOH
- 27:12 16 pins on bank GPIOZ
- 11:0 12 pins in the AO domain
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enable compile-testing for all Renesas interrupt controller drivers,
except for RENESAS_H8300H_INTC. The latter relies on a function
(ctrl_bclr()) that is not available on other architectures.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for Amazon Graviton custom variant of GICv2m, where the message
is encoded using the MSI message address, as opposed to standard
GICv2m, where the SPI number is encoded in the MSI message data.
In addition, the Graviton flavor of GICv2m is used along GICv3 (and not
GICv2).
Co-developed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Zeev Zilberman <zeev@amazon.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we run several VMs with PCI passthrough and GICv4 enabled, not
pinning vCPUs, we will occasionally see below warnings in dmesg:
ITS queue timeout (65440 65504 480)
ITS cmd its_build_vmovp_cmd failed
The reason for the above issue is that in BUILD_SINGLE_CMD_FUNC:
1. Post the write command.
2. Release the lock.
3. Start to read GITS_CREADR to get the reader pointer.
4. Compare the reader pointer to the target pointer.
5. If reader pointer does not reach the target, sleep 1us and continue
to try.
If we have several processors running the above concurrently, other
CPUs will post write commands while the 1st CPU is waiting the
completion. So we may have below issue:
phase 1:
---rd_idx-----from_idx-----to_idx--0---------
wait 1us:
phase 2:
--------------from_idx-----to_idx--0-rd_idx--
That is the rd_idx may fly ahead of to_idx, and if in case to_idx is
near the wrap point, rd_idx will wrap around. So the below condition
will not be met even after 1s:
if (from_idx < to_idx && rd_idx >= to_idx)
There is another theoretical issue. For a slow and busy ITS, the
initial rd_idx may fall behind from_idx a lot, just as below:
---rd_idx---0--from_idx-----to_idx-----------
This will cause the wait function exit too early.
Actually, it does not make much sense to use from_idx to judge if
to_idx is wrapped, but we need a initial rd_idx when lock is still
acquired, and it can be used to judge whether to_idx is wrapped and
the current rd_idx is wrapped.
We switch to a method of calculating the delta of two adjacent reads
and accumulating it to get the sum, so that we can get the real rd_idx
from the wrapped value even when the queue is almost full.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The MIPS GIC contains a block of registers used to map local interrupts
to a particular CPU interrupt pin. Since these registers are found at a
consecutive range of addresses we access them using an index, via the
(read|write)_gic_v[lo]_map accessor functions. We currently use values
from enum mips_gic_local_interrupt as those indices.
Unfortunately whilst enum mips_gic_local_interrupt provides the correct
offsets for bits in the pending & mask registers, the ordering of the
map registers is subtly different... Compared with the ordering of
pending & mask bits, the map registers move the FDC from the end of the
list to index 3 after the timer interrupt. As a result the performance
counter & software interrupts are therefore at indices 4-6 rather than
indices 3-5.
Notably this causes problems with performance counter interrupts being
incorrectly mapped on some systems, and presumably will also cause
problems for FDC interrupts.
Introduce a function to map from enum mips_gic_local_interrupt to the
index of the corresponding map register, and use it to ensure we access
the map registers for the correct interrupts.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a0dc5cb5e3 ("irqchip: mips-gic: Simplify gic_local_irq_domain_map()")
Fixes: da61fcf9d6 ("irqchip: mips-gic: Use irq_cpu_online to (un)mask all-VP(E) IRQs")
Reported-and-tested-by: Archer Yan <ayan@wavecomp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
irq_create_fwspec_mapping() can fail, returning 0 as parent_virq. In this
case vint_desc is going to be NULL in ti_sci_inta_alloc_irq() which will
cause NULL pointer dereference.
Also note that irq_create_fwspec_mapping() returns 'unsigned int' so the
check '<=' was wrong.
Use -EINVAL if irq_create_fwspec_mapping() returned with 0.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The csky,mpintc could deliver a external irq to one cpu or all cpus, but
it couldn't deliver a external irq to a group of cpus with cpu_mask. So
we only use auto deliver mode when affinity mask_val is equal to
cpu_present_mask.
There is no limitation for only two cpus in SMP system.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version you should have received a copy of the
gnu general public license along with this program if not write to
the free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify error handling by converting the driver to use managed
allocations and initializations.
Note that platform_get_resource() and ioremap_nocache() are combined in
devm_platform_ioremap_resource().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Nothing really uses irqc_priv.pdev, all users need irqc_priv.pdev->dev.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The probe function uses "&pdev->dev" a lot, hence add a shorthand for
that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to print error messages if kzalloc() or
ioremap_nocache() fail, as the memory allocation core already takes care
of that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The driver never used spinlocks, and thus does not need to include
<linux/spinlock.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a driver for the Renesas RZ/A1 Interrupt Controller.
This supports using up to 8 external interrupts on RZ/A1, with
configurable sense select.
NMI edge select is not yet supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Expose the existing EXIU hierarchical irqchip domain code to permit
the interrupt controller to be used as the irqchip component of a
GPIO controller on ACPI systems, or as the target of ordinary
interrupt resources.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation of adding support for EXIU controller devices described
via ACPI, split the DT init function in a DT specific and a generic part,
where the latter will be reused for ACPI support later.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.961286471@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to multiplatform enabled.
- Cleanups of Davinci
This tag also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release.
-----BEGIN PGP SIGNATURE-----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=pUeO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
Merge in a few pending fixes from pre-5.1 that didn't get sent in:
MAINTAINERS: update arch/arm/mach-davinci
ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
ARM: dts: imx6q-logicpd: Reduce inrush current on USBH1
ARM: dts: imx6q-logicpd: Reduce inrush current on start
ARM: dts: imx: Fix the AR803X phy-mode
ARM: dts: sun8i: a33: Reintroduce default pinctrl muxing
arm64: dts: allwinner: a64: Rename hpvcc-supply to cpvdd-supply
ARM: sunxi: fix a leaked reference by adding missing of_node_put
ARM: sunxi: fix a leaked reference by adding missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said they
should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here, due
to some changes to the kobject core code. Those too have all been acked
by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHDbw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynDAgCfbb4LBR6I50wFXb8JM/R6cAS7qrsAn1unshKV
8XCYcif2RxjtdJWXbjdm
=/rLh
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core/kobject updates from Greg KH:
"Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said
they should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here,
due to some changes to the kobject core code. Those too have all been
acked by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (47 commits)
kobject: clean up the kobject add documentation a bit more
kobject: Fix kernel-doc comment first line
kobject: Remove docstring reference to kset
firmware_loader: Fix a typo ("syfs" -> "sysfs")
kobject: fix dereference before null check on kobj
Revert "driver core: platform: Fix the usage of platform device name(pdev->name)"
init/config: Do not select BUILD_BIN2C for IKCONFIG
Provide in-kernel headers to make extending kernel easier
kobject: Improve doc clarity kobject_init_and_add()
kobject: Improve docs for kobject_add/del
driver core: platform: Fix the usage of platform device name(pdev->name)
livepatch: Replace klp_ktype_patch's default_attrs with groups
cpufreq: schedutil: Replace default_attrs field with groups
padata: Replace padata_attr_type default_attrs field with groups
irqdesc: Replace irq_kobj_type's default_attrs field with groups
net-sysfs: Replace ktype default_attrs field with groups
block: Replace all ktype default_attrs with groups
samples/kobject: Replace foo_ktype's default_attrs field with groups
kobject: Add support for default attribute groups to kobj_type
driver core: Postpone DMA tear-down until after devres release for probe failure
...
The functions mbi_compose_m{b, s}i_msg may be called from non-preemptible
context. However, on RT, iommu_dma_map_msi_msg() requires to be called
from a preemptible context.
A recent patch split iommu_dma_map_msi_msg in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The GICv3 MSI driver is reworked to avoid executing preemptible code in
non-preemptible context. This can be achieved by preparing the MSI
mapping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
[maz: only call iommu_dma_prepare_msi once, fix commit log accordingly]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ls_scfg_msi_compose_msg() may be called from non-preemptible context.
However, on RT, iommu_dma_map_msi_msg() requires to be called from a
preemptible context.
A recent patch split iommu_dma_map_msi_msg() in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The FreeScale SCFG MSI driver is reworked to avoid executing preemptible
code in non-preemptible context. This can be achieved by preparing the
MSI maping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
its_irq_compose_msi_msg() may be called from non-preemptible context.
However, on RT, iommu_dma_map_msi_msg requires to be called from a
preemptible context.
A recent change split iommu_dma_map_msi_msg() in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The GICv3 ITS driver is reworked to avoid executing preemptible code in
non-preemptible context. This can be achieved by preparing the MSI
mapping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gicv2m_compose_msi_msg() may be called from non-preemptible context.
However, on RT, iommu_dma_map_msi_msg() requires to be called from a
preemptible context.
A recent change split iommu_dma_map_msi_msg() in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The GICv2m driver is reworked to avoid executing preemptible code in
non-preemptible context. This can be achieved by preparing the MSI
mapping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a msi domain that is child to the INTA domain. Clients
uses the INTA MSI bus layer to allocate irqs in this
MSI domain.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Texas Instruments' K3 generation SoCs has an IP Interrupt Aggregator
which is an interrupt controller that does the following:
- Converts events to interrupts that can be understood by
an interrupt router.
- Allows for multiplexing of events to interrupts.
Configuration of the interrupt aggregator registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol. Add the required infrastructure to
allow the allocation and routing of these events.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Texas Instruments' K3 generation SoCs has an IP Interrupt Router
that does allows for redirection of input interrupts to host
interrupt controller. Interrupt Router inputs are either from a
peripheral or from an Interrupt Aggregator which is another
interrupt controller.
Configuration of the interrupt router registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol.
Add support for Interrupt Router driver over TISCI protocol.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to print a message if devm_kzalloc() fails, as the
memory allocation core already takes care of that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
IRQ_DOMAIN_HIERARCHY selects IRQ_DOMAIN, hence there is no need for
drivers to select both.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Using list_add + list_sort to insert an element and keeping the list
sorted is a somewhat blunt instrument; one can find the right place to
insert in fewer lines of code than the cmp callback uses. Moreover,
walking the entire list afterwards to merge adjacent ranges is
overkill, since we know that only the just-inserted element may be
merged with its neighbours.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There's no reason to ask kmalloc() to zero the allocation, since all
the fields get initialized immediately afterwards. Except that there's
also not any reason to initialize the ->entry member, since the
element gets added to the lpi_range_list immediately.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There's no reason to do the allocation of the new lpi_range inside the
lpi_range_lock. One could change the code to avoid the allocation
altogether in case the freed range can be merged with one or two
existing ranges (in which case the allocation would naturally be done
under the lock), but it's probably not worth complicating the code for
that.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This irqchip driver uses the hwspinlock framework (coprocessor HW regs
access concurrency) for the stm32mp1-exti device.
Hence, this driver needs to handle the hwspinlock driver dependency
using the deferred probe mechanism which requires to move this driver
into a platform one with a probe() ops.
This applies only for the device which is "st,stm32mp1-exti" compatible,
the management of the other devices (st,stm32h7-exti / st,stm32-exti) is
kept unchanged (use IRQCHIP_DECLARE)
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If interrupts are enabled for a non-root GIC device that uses the
gic-pm driver, when system suspend occurs, the current interrupt
state is not saved and restored correctly and so interrupts do not
work again on resuming the system. Add a late suspend handler to
save and restore the state for these devices.
Suggested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gic-pm driver is using pm-clk framework to manage clock resources, where
clocks remain always ON. This happens on Tegra devices which use BPMP
co-processor to manage the clocks. Calls to BPMP are always blocking and
hence it is necessary to enable/disable clocks during prepare/unprepare
phase respectively. When pm-clk is used, prepare count of clock is not
balanced until pm_clk_remove() happens. Clock is prepared in the driver
probe() and thus prepare count of clock remains non-zero, which in turn
keeps clock ON always.
Please note that above mentioned behavior is specific to Tegra devices
using BPMP for clock management and this should not be seen on other
devices. Though this patch uses clk_bulk APIs to address the mentioned
behavior, this works fine for all devices.
To simplify gic_get_clocks() API is removed and instead probe can do
necessary setup.
Suggested-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The word 'entirely' has been misspelt in a comment in its_msi_prepare().
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
It is useful to print which interrupt controllers are registered in the
system and which parent IRQ they use, especially given that L2 interrupt
controllers do not call request_irq() on their parent interrupt and do
not appear under /proc/interrupts for that reason.
We used to print the base register address virtual address which had
little value, use %pOF to print the path to the Device Tree node which
maps to the physical address more easily and is what people need to
troubleshoot systems.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcvxsRAAoJEEEQszewGV1zZE8QAIrpxZGGKUv7o/NrtR2J8CLR
jl7cm8Rx+TVlowEz4Un2erhMEFEIp91DeKsN76fBaAszmogbuck1u+ZiArpL7u12
sJzYwQUqyCuGFQbiOIu1PyYCCGebVvZYvYjoEDzt5GOp5rCNh6xsP9eDQe7F8ZgE
60iKiLEp+U3VQXB7+/KdvIpVVM2V7wJyKHtKkZVsTEH0iKsTy6yormBZc3r/a1Ka
7fZDLC6KLtaQ95YpqL+L/ZZNickj/J2wqnVuh4GrzsJ5m9GphoUfD2X3jtuQyjo/
VlHy7mEmWAvS68lQXNibXLi9h8tNr9XApRDH/snoLRq4KKM8P30OgZMc28IWBqwZ
CqbxfN9++ffZBt5udY3Jfdsj3lgDOMjBzvfIJpQxLbFCfTaQWtBZ5KaILGdcCuFH
TdCUT5tS/G7XUlsAkFQc1ubseYl3PmGgBrTh6N150hNH45xsuniaBUv/RgltA7ZY
Q437ctUs5IySPOm3dPzgHQwqC1TN/LuHX3fbQwcgj792iZhn5hExazmgLYGwzy/l
vLM9izG7NerZQgpspaUq1jeCPVVCsZ2q/n8vWD7beBLWTo7bZhg0uLXQOwR/9ITc
B5vC0h9Fe9O732ZZY5FgJXYgUkQ9fRjN/lMv6RWgPlc6/r8eQZ+OimAprpmB96Gu
2IfYAFI4lZDS/nJL9FmF
=0U95
-----END PGP SIGNATURE-----
Merge tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/soc
This modernizes the IXP4xx platform and adds initial Device Tree
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
* tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: (31 commits)
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
ARM: ixp4xx: Move IXP4xx QMGR and NPE headers
ARM: ixp4xx: Move NPE and QMGR to drivers/soc
ARM: dts: Add some initial IXP4xx device trees
ARM: ixp4xx: Add device tree boot support
ARM: ixp4xx: Add DT bindings
gpio: ixp4xx: Add OF probing support
gpio: ixp4xx: Add DT bindings
clocksource/drivers/ixp4xx: Add OF initialization support
clocksource/drivers/ixp4xx: Add DT bindings
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for probing and settin up the IXP4xx
irqchip from device tree.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Fix indirect syscall tracing & seccomp filtering for big endian MIPS64
kernels, which previously loaded the syscall number incorrectly &
would always use zero.
- Fix performance counter IRQ setup for Atheros/ath79 SoCs, allowing
perf to function on those systems.
And not really a fix, but a useful addition:
- Add a Broadcom mailing list to the MAINTAINERS entry for BMIPS systems
to allow relevant engineers to track patch submissions.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXL4GhRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN15CQEA6ZtDNid9bRuD3lEOqiJTHrgUIvjA
sxVB5MwckzQ7Ir4A+wS6P4oIjlMdJxO0MZ23QlNNP+XibRt/jAz8ItLoNpcJ
=Cl5u
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_5.1_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A couple more MIPS fixes:
- Fix indirect syscall tracing & seccomp filtering for big endian
MIPS64 kernels, which previously loaded the syscall number
incorrectly & would always use zero.
- Fix performance counter IRQ setup for Atheros/ath79 SoCs, allowing
perf to function on those systems.
And not really a fix, but a useful addition:
- Add a Broadcom mailing list to the MAINTAINERS entry for BMIPS
systems to allow relevant engineers to track patch submissions"
* tag 'mips_fixes_5.1_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: perf: ath79: Fix perfcount IRQ assignment
MIPS: scall64-o32: Fix indirect syscall number load
MAINTAINERS: BMIPS: Add internal Broadcom mailing list
The IXP4xx (arch/arm/mach-ixp4xx) is an old Intel XScale
platform that has very wide deployment and use.
As part of modernizing the platform, we need to implement a
proper irqchip in the irqchip subsystem.
The IXP4xx irqchip is tightly jotted together with the GPIO
controller, and whereas in the past we would deal with this
complex logic by adding necessarily different code, we can
nowadays modernize it using a hierarchical irqchip.
The actual IXP4 irqchip is a simple active low level IRQ
controller, whereas the GPIO functionality resides in a
different memory area and adds edge trigger support for
the interrupts.
The interrupts from GPIO lines 0..12 are 1:1 mapped to
a fixed set of hardware IRQs on this IRQchip, so we
expect the child GPIO interrupt controller to go in and
allocate descriptors for these interrupts.
For the other interrupts, as we do not yet have DT
support for this platform, we create a linear irqdomain
and then go in and allocate the IRQs that the legacy
boards use. This code will be removed on the DT probe
path when we add DT support to the platform.
We add some translation code for supporting DT
translations for the fwnodes, but we leave most of that
for later.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.
On TP-Link Archer C7v5:
CPU0
2: 0 MIPS 2 ath9k
4: 318 MIPS 4 19000000.eth
7: 55034 MIPS 7 timer
8: 1236 MISC 3 ttyS0
12: 0 INTC 1 ehci_hcd:usb1
13: 0 gpio-ath79 2 keys
14: 0 gpio-ath79 5 keys
15: 31 AR724X PCI 1 ath10k_pci
$ perf top
genirq: Flags mismatch irq 13. 00014c83 (mips_perf_pmu) vs. 00002003 (keys)
On TP-Link Archer C7v4:
CPU0
4: 0 MIPS 4 19000000.eth
5: 7135 MIPS 5 1a000000.eth
7: 98379 MIPS 7 timer
8: 30 MISC 3 ttyS0
12: 90028 INTC 0 ath9k
13: 5520 INTC 1 ehci_hcd:usb1
14: 4623 INTC 2 ehci_hcd:usb2
15: 32844 AR724X PCI 1 ath10k_pci
16: 0 gpio-ath79 16 keys
23: 0 gpio-ath79 23 keys
$ perf top
genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1)
This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.
So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.
Tested-by: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Currently, when irq_domain_add_linear() fails, the error code does not get
set so it returns zero which is wrong. Fix it by setting the appropriate
error code.
Fixes: 9e543e22e2 ("irqchip: Add driver for Loongson-1 interrupt controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20190329062136.GQ32613@kadam
Parsing entries in an ACPI table had assumed a generic header
structure. There is no standard ACPI header, though, so less common
layouts with different field sizes required custom parsers to go through
their subtable entry list.
Create the infrastructure for adding different table types so parsing
the entries array may be more reused for all ACPI system tables and
the common code doesn't need to be duplicated.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/irqchip/irq-mvebu-sei.c:481:23: warning:
symbol 'mvebu_sei_ap806_caps' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <jason@lakedaemon.net>
Cc: <andrew@lunn.ch>
Cc: <gregory.clement@bootlin.com>
Cc: <sebastian.hesselbarth@gmail.com>
Cc: <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lkml.kernel.org/r/20190321151448.15600-1-yuehaibing@huawei.com
mbigen_write_msg clears eventid bits of a mbigen register
when free a interrupt, because msi_domain_deactivate memset
struct msg to zero. Then multiple mbigen pins with zero eventid
will report the same interrupt number.
The eventid clear call trace:
free_irq
__free_irq
irq_shutdown
irq_domain_deactivate_irq
__irq_domain_deactivate_irq
__irq_domain_deactivate_irq
msi_domain_deactivate
platform_msi_write_msg
mbigen_write_msg
Signed-off-by: Jianguo Chen <chenjianguo3@huawei.com>
[maz: massaged subject]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The rising configuration status register (rtsr) is not banked.
As it is shared with the co-processor, it should not be written at probe
time, else the co-processor configuration will be lost.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Falling and rising configuration and status registers are not banked.
As they are shared with M4 co-processor, they should not be cleared
at probe time, else M4 co-processor configuration will be lost.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Fix sparse warning:
drivers/irqchip/irq-mmp.c:182:29: warning:
symbol 'mmp_irq_domain_ops' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Fix sparse warnings:
drivers/irqchip/irq-brcmstb-l2.c:278:12: warning:
symbol 'brcmstb_l2_edge_intc_of_init' was not declared. Should it be static?
drivers/irqchip/irq-brcmstb-l2.c:285:12: warning:
symbol 'brcmstb_l2_lvl_intc_of_init' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The lpi_range_list is supposed to be sorted in ascending order of
->base_id (at least if the range merging is to work), but the current
comparison function returns a positive value if rb->base_id >
ra->base_id, which means that list_sort() will put A after B in that
case - and vice versa, of course.
Fixes: 880cb3cddd (irqchip/gic-v3-its: Refactor LPI allocator)
Cc: stable@vger.kernel.org (v4.19+)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We do not have any in-tree platform with this pathological setup,
and only a single system (Cavium's cns3xxx) isn't DT aware.
Let's drop the secondary GIC support for now, until we remove
the above horror altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Pseudo NMI support for arm64 using GICv3 interrupt priorities
- uaccess macros clean-up (unsafe user accessors also merged but
reverted, waiting for objtool support on arm64)
- ptrace regsets for Pointer Authentication (ARMv8.3) key management
- inX() ordering w.r.t. delay() on arm64 and riscv (acks in place by the
riscv maintainers)
- arm64/perf updates: PMU bindings converted to json-schema, unused
variable and misleading comment removed
- arm64/debug fixes to ensure checking of the triggering exception level
and to avoid the propagation of the UNKNOWN FAR value into the si_code
for debug signals
- Workaround for Fujitsu A64FX erratum 010001
- lib/raid6 ARM NEON optimisations
- NR_CPUS now defaults to 256 on arm64
- Minor clean-ups (documentation/comments, Kconfig warning, unused
asm-offsets, clang warnings)
- MAINTAINERS update for list information to the ARM64 ACPI entry
-----BEGIN PGP SIGNATURE-----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=2U56
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- Pseudo NMI support for arm64 using GICv3 interrupt priorities
- uaccess macros clean-up (unsafe user accessors also merged but
reverted, waiting for objtool support on arm64)
- ptrace regsets for Pointer Authentication (ARMv8.3) key management
- inX() ordering w.r.t. delay() on arm64 and riscv (acks in place by
the riscv maintainers)
- arm64/perf updates: PMU bindings converted to json-schema, unused
variable and misleading comment removed
- arm64/debug fixes to ensure checking of the triggering exception
level and to avoid the propagation of the UNKNOWN FAR value into the
si_code for debug signals
- Workaround for Fujitsu A64FX erratum 010001
- lib/raid6 ARM NEON optimisations
- NR_CPUS now defaults to 256 on arm64
- Minor clean-ups (documentation/comments, Kconfig warning, unused
asm-offsets, clang warnings)
- MAINTAINERS update for list information to the ARM64 ACPI entry
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
arm64: mmu: drop paging_init comments
arm64: debug: Ensure debug handlers check triggering exception level
arm64: debug: Don't propagate UNKNOWN FAR into si_code for debug signals
Revert "arm64: uaccess: Implement unsafe accessors"
arm64: avoid clang warning about self-assignment
arm64: Kconfig.platforms: fix warning unmet direct dependencies
lib/raid6: arm: optimize away a mask operation in NEON recovery routine
lib/raid6: use vdupq_n_u8 to avoid endianness warnings
arm64: io: Hook up __io_par() for inX() ordering
riscv: io: Update __io_[p]ar() macros to take an argument
asm-generic/io: Pass result of I/O accessor to __io_[p]ar()
arm64: Add workaround for Fujitsu A64FX erratum 010001
arm64: Rename get_thread_info()
arm64: Remove documentation about TIF_USEDFPU
arm64: irqflags: Fix clang build warnings
arm64: Enable the support of pseudo-NMIs
arm64: Skip irqflags tracing for NMI in IRQs disabled context
arm64: Skip preemption when exiting an NMI
arm64: Handle serror in NMI context
irqchip/gic-v3: Allow interrupts to be set as pseudo-NMI
...
Here are two branches that came relatively late during the linux-5.0
development cycle and have dependencies on the other branches:
- On the TI OMAP platform, the CPSW Ethernet PHY mode selection driver
is being replaced, this puts the final pieces in place
- On the DaVinci platform, the interrupt handling code in arch/arm
gets moved into a regular device driver in drivers/irqchip.
Since they both had some time in linux-next after the 5.0-rc8
release, I'm sending them along with the other updates.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJcf9ZXAAoJEGCrR//JCVIn4NgP/0Q0+qP1QTmc/XL1yzSKhemg
PVu42+EtoR/tyaTu+spf/aQyJiC/1E9NE7n9r9FvQqpxxlipv6XLxZbti89C83mL
Ynk2D3Z2FjDZvVSl7WdgX9J/GoaJPXefTkfUr4ZZtcMNhLOCl2ATOO6ytuAXid7Q
keTfHKI2rwUWFmu+ojGuONdyM3BA12hEYNH+B12rnXAcy8ylb70XMxitPx5JGkJX
ZdhG58tGNM3EDdQh7mornlFA17IUqrYpt/daIBDZaPwwz3P8+vkMTl10IkEsvIcA
soMmiAp75jYlnLec8A9awGFBzPznzxH7a9PdvPByW044kARSgfFDRbijmwAij6oA
CHCEmmFP9LOm9zP8qqC0lsfwOBOnSL8b7pFXL2jTJQO897hfBLQSUTVFQ8K3Sznx
p8CCv++YU2ZQT6rGg7qRIApvfjNtRimBykCyy0Nh03MDUUgNosfqff8EvSXMbsbs
BwjBavM1QhF2E6trKrxEi3n3+WrHK1JjVL0JxP2rQlraifRrSUXQglqiAOXl4mN7
GRIjwI5WYeRKMj7nqgj10MO/GBbDAmME482U2+0RvEX2pm/wUiVQjm/6zWOp5Be/
cAcH61hEXxQbTXh0aVmzSKUHuFVCGl2FC75/JWVzRosdmval7C1MgILiucrXKUVe
hhF12S1z45yfZRwY7sVD
=0u1N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Arnd Bergmann:
"Here are two branches that came relatively late during the linux-5.0
development cycle and have dependencies on the other branches:
- On the TI OMAP platform, the CPSW Ethernet PHY mode selection
driver is being replaced, this puts the final pieces in place
- On the DaVinci platform, the interrupt handling code in arch/arm
gets moved into a regular device driver in drivers/irqchip.
Since they both had some time in linux-next after the 5.0-rc8 release,
I'm sending them along with the other updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
net: ethernet: ti: cpsw: deprecate cpsw-phy-sel driver
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
...
Pull irq updates from Thomas Gleixner:
"The interrupt departement delivers this time:
- New infrastructure to manage NMIs on platforms which have a sane
NMI delivery, i.e. identifiable NMI vectors instead of a single
lump.
- Simplification of the interrupt affinity management so drivers
don't have to implement ugly loops around the PCI/MSI enablement.
- Speedup for interrupt statistics in /proc/stat
- Provide a function to retrieve the default irq domain
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- The usual small fixes, improvements and cleanups all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
irqchip/imx-irqsteer: Add multi output interrupts support
irqchip/imx-irqsteer: Change to use reg_num instead of irq_group
dt-bindings: irq: imx-irqsteer: Add multi output interrupts support
dt-binding: irq: imx-irqsteer: Use irq number instead of group number
irqchip/brcmstb-l2: Use _irqsave locking variants in non-interrupt code
irqchip/gicv3-its: Use NUMA aware memory allocation for ITS tables
irqdomain: Allow the default irq domain to be retrieved
irqchip/sifive-plic: Implement irq_set_affinity() for SMP host
irqchip/sifive-plic: Differentiate between PLIC handler and context
irqchip/sifive-plic: Add warning in plic_init() if handler already present
irqchip/sifive-plic: Pre-compute context hart base and enable base
PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
genirq/affinity: Remove the leftovers of the original set support
nvme-pci: Simplify interrupt allocation
genirq/affinity: Add new callback for (re)calculating interrupt sets
genirq/affinity: Store interrupt sets size in struct irq_affinity
genirq/affinity: Code consolidation
irqchip/irq-sifive-plic: Check and continue in case of an invalid cpuid.
irqchip/i8259: Fix shutdown order by moving syscore_ops registration
dt-bindings: interrupt-controller: loongson ls1x intc
...
gcc points out that irqs_num is not initialized when of_property_read_u32()
is an empty stub function:
Included from drivers/irqchip/irq-imx-irqsteer.c:7:
drivers/irqchip/irq-imx-irqsteer.c: In function 'imx_irqsteer_probe':
include/uapi/linux/kernel.h:13:49: error: 'irqs_num' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The same can actually happen with CONFIG_OF=y as well, though we don't
get a warning then.
Add error checking here that lets the code deal with missing or
invalid properties as well as avoid the warning.
Fixes: 28528fca49 ("irqchip/imx-irqsteer: Add multi output interrupts support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Core pseudo-NMI handling code
- Allow the default irq domain to be retrieved
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- A handful of other fixes (i8259, GICv3, PLIC)
-----BEGIN PGP SIGNATURE-----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=M6YA
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier
- Core pseudo-NMI handling code
- Allow the default irq domain to be retrieved
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- A handful of other fixes (i8259, GICv3, PLIC)
One irqsteer channel can support up to 8 output interrupts.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
One group can manage 64 interrupts by using two registers (e.g. STATUS/SET).
However, the integrated irqsteer may support only 32 interrupts which
needs only one register in a group. But the current driver assume there's
a mininum of two registers in a group which result in a wrong register map
for 32 interrupts per channel irqsteer. Let's use the reg_num caculated by
interrupts per channel instead of irq_group to cover this case.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Using the irq_gc_lock/irq_gc_unlock functions in the suspend and
resume functions creates the opportunity for a deadlock during
suspend, resume, and shutdown. Using the irq_gc_lock_irqsave/
irq_gc_unlock_irqrestore variants prevents this possible deadlock.
Cc: stable@vger.kernel.org
Fixes: 7f646e9276 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[maz: tidied up $SUBJECT]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The NUMA node information is visible to ITS driver but not being used
other than handling hardware errata. ITS/GICR hardware accesses to the
local NUMA node is usually quicker than the remote NUMA node. How slow
the remote NUMA accesses are depends on the implementation details.
This patch allocates memory for ITS management tables and command
queue from the corresponding NUMA node using the appropriate NUMA
aware functions. This change improves the performance of the ITS
tables read latency on systems where it has more than one ITS block,
and with the slower inter node accesses.
Apache Web server benchmarking using ab tool on a HiSilicon D06
board with multiple numa mem nodes shows Time per request and
Transfer rate improvements of ~3.6% with this patch.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Ganapatrao Kulkarni <gkulkarni@marvell.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently on SMP host, all CPUs take external interrupts routed via
PLIC. All CPUs will try to claim a given external interrupt but only
one of them will succeed while other CPUs would simply resume whatever
they were doing before. This means if we have N CPUs then for every
external interrupt N-1 CPUs will always fail to claim it and waste
their CPU time.
Instead of above, external interrupts should be taken by only one CPU
and we should have provision to explicitly specify IRQ affinity from
kernel-space or user-space.
This patch provides irq_set_affinity() implementation for PLIC driver.
It also updates irq_enable() such that PLIC interrupts are only enabled
for one of CPUs specified in IRQ affinity mask.
With this patch in-place, we can change IRQ affinity at any-time from
user-space using procfs.
Example:
/ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
8: 44 0 0 0 SiFive PLIC 8 virtio0
10: 48 0 0 0 SiFive PLIC 10 ttyS0
IPI0: 55 663 58 363 Rescheduling interrupts
IPI1: 0 1 3 16 Function call interrupts
/ #
/ #
/ # echo 4 > /proc/irq/10/smp_affinity
/ #
/ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
8: 45 0 0 0 SiFive PLIC 8 virtio0
10: 160 0 17 0 SiFive PLIC 10 ttyS0
IPI0: 68 693 77 410 Rescheduling interrupts
IPI1: 0 2 3 16 Function call interrupts
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We explicitly differentiate between PLIC handler and context because
PLIC context is for given mode of HART whereas PLIC handler is per-CPU
software construct meant for handling interrupts from a particular
PLIC context.
To achieve this differentiation, we rename "nr_handlers" to "nr_contexts"
and "nr_mapped" to "nr_handlers" in plic_init().
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We have two enteries (one for M-mode and another for S-mode) in the
interrupts-extended DT property of PLIC DT node for each HART. It is
expected that firmware/bootloader will set M-mode HWIRQ line of each
HART to 0xffffffff (i.e. -1) in interrupts-extended DT property
because Linux runs in S-mode only.
If firmware/bootloader is buggy then it will not correctly update
interrupts-extended DT property which might result in a plic_handler
configured twice. This patch adds a warning in plic_init() if a
plic_handler is already marked present. This warning provides us
a hint about incorrectly updated interrupts-extended DT property.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch does following optimizations:
1. Pre-compute hart base for each context handler
2. Pre-compute enable base for each context handler
3. Have enable lock for each context handler instead
of global plic_toggle_lock
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-------------------------------------
This pull request gets rid of mach-davinci private interrupt controller
implmentations (aintc and cp_initc) and moves them to drivers/irqchip.
mach/irqs.h usage outside of mach-davinci has been rid of.
The driver changes (input and irqchip) have been acked by respective
maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VjX6
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v5.1/soc-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/late
DaVinci SoC updates for v5.1 (part 3)
-------------------------------------
This pull request gets rid of mach-davinci private interrupt controller
implmentations (aintc and cp_initc) and moves them to drivers/irqchip.
mach/irqs.h usage outside of mach-davinci has been rid of.
The driver changes (input and irqchip) have been acked by respective
maintainers.
* tag 'davinci-for-v5.1/soc-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (57 commits)
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
ARM: davinci: aintc: unify error handling
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cp-intc driver has now been cleaned up. Move it to drivers/irqchip
where it belongs.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The aintc driver has now been cleaned up. Move it to drivers/irqchip
where it belongs. There's no device-tree support for any dm* board so
there's no IRQCHIP_OF_DECLARE() - there's only the exported init
function called from machine code.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
riscv_hartid_to_cpuid can return invalid cpuid for a hart that is
present in DT but was never brought up.
Print the appropriate warning message and continue.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When using cpufreq on Loongson 2F MIPS platform, "poweroff"
command gets frequently stuck in syscore_shutdown(). The reason is
that i8259A_shutdown() gets called before cpufreq_suspend(), and if we
have pending work then irq_work_sync() in cpufreq_dbs_governor_stop()
gets stuck forever as we have all interrupts masked already.
irq-i8259 is registering syscore_ops using device_initcall(),
while cpufreq uses core_initcall(). Fix the shutdown order simply
by registering the irq syscore_ops during the early IRQ init instead
of using a separate initcall at later stage.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This controller appeared on Loongson-1 family MCUs
including Loongson-1B and Loongson-1C.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In current logic, its_parse_indirect_baser() will be invoked twice
when allocating Device tables. Add a *break* to omit the unnecessary
and annoying (might be ...) invoking.
Fixes: 32bd44dc19 ("irqchip/gic-v3-its: Fix the incorrect parsing of VCPU table size")
Cc: stable@vger.kernel.org
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull irq fixes from Ingo Molnar:
"irqchip driver fixes: most of them are race fixes for ARM GIC (General
Interrupt Controller) variants, but also a fix for the ARM MMP
(Marvell PXA168 et al) irqchip affecting OLPC keyboards"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix ITT_entry_size accessor
irqchip/mmp: Only touch the PJ4 IRQ & FIQ bits on enable/disable
irqchip/gic-v3-its: Gracefully fail on LPI exhaustion
irqchip/gic-v3-its: Plug allocation race for devices sharing a DevID
irqchip/gic-v4: Fix occasional VLPI drop
- Another GICv3 ITS fix for devices sharing the same DevID
- Don't return invalid data on exhaustion of the GICv3 LPI pool
- Fix a GICv3 field decoding bug leading to memory over-allocation
- Init GICv4 at boot time instead of lazy init
- Fix interrupt masking on PJ4
-----BEGIN PGP SIGNATURE-----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=Crvb
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates from Marc Zyngier:
- Another GICv3 ITS fix for devices sharing the same DevID
- Don't return invalid data on exhaustion of the GICv3 LPI pool
- Fix a GICv3 field decoding bug leading to memory over-allocation
- Init GICv4 at boot time instead of lazy init
- Fix interrupt masking on PJ4
Implement NMI callbacks for GICv3 irqchip. Install NMI safe handlers
when setting up interrupt line as NMI.
Only SPIs and PPIs are allowed to be set up as NMI.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Provide a higher priority to be used for pseudo-NMIs. When such an
interrupt is received, keep interrupts fully disabled at CPU level to
prevent receiving other pseudo-NMIs while handling the current one.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The values non secure EL1 needs to use for PMR and RPR registers depends on
the value of SCR_EL3.FIQ.
The values non secure EL1 sees from the distributor and redistributor
depend on whether security is enabled for the GIC or not.
To avoid having to deal with two sets of values for PMR
masking/unmasking, only enable pseudo-NMIs when GIC has non-secure view
of priorities.
Also, add firmware requirements related to SCR_EL3.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Once the boot CPU has been prepared or a new secondary CPU has been
brought up, use ICC_PMR_EL1 to mask interrupts on that CPU and clear
PSR.I bit.
Since ICC_PMR_EL1 is initialized at CPU bringup, avoid overwriting
it in the GICv3 driver.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The code to detect whether Linux has access to group0 interrupts can
prove useful in other parts of the driver.
Provide a separate function to do this.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mask the IRQ priority through PMR and re-enable IRQs at CPU level,
allowing only higher priority interrupts to be received during interrupt
handling.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- fix ccount_timer_shutdown for secondary CPUs;
- fix secondary CPU initialization;
- fix secondary CPU reset vector clash with double exception vector;
- fix present CPUs when booting with 'maxcpus' parameter;
- limit possible CPUs by configured NR_CPUS;
- issue a warning if xtensa PIC is asked to retrigger anything other
than software IRQ;
- fix masking/unmasking of the first two IRQs on xtensa MX PIC;
- fix typo in Kconfig description for user space unaligned access
feature;
- fix Kconfig warning for selecting BUILTIN_DTB.
-----BEGIN PGP SIGNATURE-----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=Pim9
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20190201' of git://github.com/jcmvbkbc/linux-xtensa
Pull xtensa fixes from Max Filippov:
- fix ccount_timer_shutdown for secondary CPUs
- fix secondary CPU initialization
- fix secondary CPU reset vector clash with double exception vector
- fix present CPUs when booting with 'maxcpus' parameter
- limit possible CPUs by configured NR_CPUS
- issue a warning if xtensa PIC is asked to retrigger anything other
than software IRQ
- fix masking/unmasking of the first two IRQs on xtensa MX PIC
- fix typo in Kconfig description for user space unaligned access
feature
- fix Kconfig warning for selecting BUILTIN_DTB
* tag 'xtensa-20190201' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: SMP: limit number of possible CPUs by NR_CPUS
xtensa: rename BUILTIN_DTB to BUILTIN_DTB_SOURCE
xtensa: Fix typo use space=>user space
drivers/irqchip: xtensa-mx: fix mask and unmask
drivers/irqchip: xtensa: add warning to irq_retrigger
xtensa: SMP: mark each possible CPU as present
xtensa: smp_lx200_defconfig: fix vectors clash
xtensa: SMP: fix secondary CPU initialization
xtensa: SMP: fix ccount_timer_shutdown
Resetting bit 4 disables the interrupt delivery to the "secure
processor" core. This breaks the keyboard on a OLPC XO 1.75 laptop,
where the firmware running on the "secure processor" bit-bangs the
PS/2 protocol over the GPIO lines.
It is not clear what the rest of the bits are and Marvell was unhelpful
when asked for documentation. Aside from the SP bit, there are probably
priority bits.
Leaving the unknown bits as the firmware set them up seems to be a wiser
course of action compared to just turning them off.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
[maz: fixed-up subject and commit message]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In the unlikely event that we cannot find any available LPI in the
system, we should gracefully return an error instead of carrying
on with no LPI allocated at all.
Fixes: 38dd7c494c ("irqchip/gic-v3-its: Drop chunk allocation compatibility")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On systems or VMs where multiple devices share a single DevID
(because they sit behind a PCI bridge, or because the HW is
broken in funky ways), we reuse the save its_device structure
in order to reflect this.
It turns out that there is a distinct lack of locking when looking
up the its_device, and two device being probed concurrently can result
in double allocations. That's obviously not nice.
A solution for this is to have a per-ITS mutex that serializes device
allocation.
A similar issue exists on the freeing side, which can run concurrently
with the allocation. On top of now taking the appropriate lock, we
also make sure that a shared device is never freed, as we have no way
to currently track the life cycle of such object.
Reported-by: Zheng Xiang <zhengxiang9@huawei.com>
Tested-by: Zheng Xiang <zhengxiang9@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
1. In current implementation, every VLPI will temporarily be mapped to
the first CPU in system (normally CPU0) and then moved to the real
scheduled CPU later.
2. So there is a time window and a VLPI may be sent to CPU0 instead of
the real scheduled vCPU, in a multi-CPU virtual machine.
3. However, CPU0 may have not been scheduled as a virtual CPU after
system boots up, so the value of its GICR_VPROPBASER is unknown at
that moment.
4. If the INTID of VLPI is larger than 2^(GICR_VPROPBASER.IDbits+1),
while IDbits is also in unknown state, GIC will behave as if the VLPI
is out of range and simply drop it, which results in interrupt missing
in Guest.
As no code will clear GICR_VPROPBASER at runtime, we can safely
initialize the IDbits field at boot time for each CPU to get rid of
this issue.
We also clear Valid bit of GICR_VPENDBASER in case any ancient
programming gets left in and causes memory corrupting. A new function
its_clear_vpend_valid() is added to reuse the code in
its_vpe_deschedule().
Fixes: e643d80340 ("irqchip/gic-v3-its: Add VPE scheduling")
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
xtensa_irq_mask and xtensa_irq_unmask don't do the right thing when
called for the first two external IRQs. Treat these IRQs as per-CPU
IRQs.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
XEA2 and MX PIC can only retrigger software interrupts. Issue a warning
if an interrupt of any other type is retriggered.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- Add missing DT translation call in stm32-exti
- Fix uninitialized mutex in the GICv3 MBI support code
- Drop useless GPIO includes from the madera driver
- Fix PCI Multi-MSI allocation with aliasing devices on GICv3 ITS
-----BEGIN PGP SIGNATURE-----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=ZA7f
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates from Marc Zyngier
- Add missing DT translation call in stm32-exti
- Fix uninitialized mutex in the GICv3 MBI support code
- Drop useless GPIO includes from the madera driver
- Fix PCI Multi-MSI allocation with aliasing devices on GICv3 ITS
The way we allocate events works fine in most cases, except
when multiple PCI devices share an ITS-visible DevID, and that
one of them is trying to use MultiMSI allocation.
In that case, our allocation is not guaranteed to be zero-based
anymore, and we have to make sure we allocate it on a boundary
that is compatible with the PCI Multi-MSI constraints.
Fix this by allocating the full region upfront instead of iterating
over the number of MSIs. MSI-X are always allocated one by one,
so this shouldn't change anything on that front.
Fixes: b48ac83d6b ("irqchip: GICv3: ITS: MSI support")
Cc: stable@vger.kernel.org
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This irqchip does not use anything GPIO-related so drop
the GPIO includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The mbi_lock mutex is left uninitialized, so let's use DEFINE_MUTEX
to initialize it statically.
Fixes: 505287525c ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Domain translate function is needed to recover irq
configuration parameters from DT node
Fixes: 927abfc446 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The handle_irq_perbit function loop every bit in hwirq local variable.
handle_irq_perbit(hwirq) {
for_everyt_bit_in(hwirq) {
handle_domain_irq()
->irq_exit()
->invoke_softirq()
->__do_softirq()
->local_irq_enable() // Here will cause new interrupt.
}
}
When new interrupt coming at local_irq_enable, it will finish another
interrupt handler and pull down the interrupt source. But hwirq is the
local variable for handle_irq_perbit(), it can't get new interrupt
controller pending reg status. So we need update hwirq with pending reg
in every loop.
Also change write_relax to writel could prevent stw from fast retire.
When local_irq is enabled, intc regs is really set-in.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Lu Baoquan <lu.baoquan@intellif.com>
- switch to generated syscall table
- switch ptrace to regsets, use regsets for core dumps
- complete tracehook implementation
- add syscall tracepoints support
- add jumplabels support
- add memtest support
- drop unused/duplicated code from entry.S, ptrace.c, coprocessor.S,
elf.h and syscall.h
- clean up warnings caused by WSR/RSR macros
- clean up DTC warnings about SPI controller node names in xtfpga.dtsi
- simplify coprocessor.S
- get rid of explicit 'l32r' instruction usage in assembly
-----BEGIN PGP SIGNATURE-----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=LqC4
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20181228' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa updates from Max Filippov:
- switch to generated syscall table
- switch ptrace to regsets, use regsets for core dumps
- complete tracehook implementation
- add syscall tracepoints support
- add jumplabels support
- add memtest support
- drop unused/duplicated code from entry.S, ptrace.c, coprocessor.S,
elf.h and syscall.h
- clean up warnings caused by WSR/RSR macros
- clean up DTC warnings about SPI controller node names in xtfpga.dtsi
- simplify coprocessor.S
- get rid of explicit 'l32r' instruction usage in assembly
* tag 'xtensa-20181228' of git://github.com/jcmvbkbc/linux-xtensa: (25 commits)
xtensa: implement jump_label support
xtensa: implement syscall tracepoints
xtensa: implement tracehook functions and enable HAVE_ARCH_TRACEHOOK
xtensa: enable CORE_DUMP_USE_REGSET
xtensa: implement TIE regset
xtensa: implement task_user_regset_view
xtensa: call do_syscall_trace_{enter,leave} selectively
xtensa: use NO_SYSCALL instead of -1
xtensa: define syscall_get_arch()
Move EM_XTENSA to uapi/linux/elf-em.h
xtensa: support memtest
xtensa: don't use l32r opcode directly
xtensa: xtfpga.dtsi: fix dtc warnings about SPI
xtensa: don't clear cpenable unconditionally on release
xtensa: simplify coprocessor.S
xtensa: clean up WSR*/RSR*/get_sr/set_sr
xtensa: drop unused declarations from elf.h
xtensa: clean up syscall.h
xtensa: drop unused coprocessor helper functions
xtensa: drop custom PTRACE_{PEEK,POKE}{TEXT,DATA}
...
Here is the nds32 patch set based on 4.20-rc1.
Contained in here are
1. Perf support
2. Power management support
3. FPU support
4. Hardware prefetcher support
5. Build error fixed
6. Performance enhancement
These are the LTP20170427 testing results.
Total Tests: 1902
Total Skipped Tests: 603
Total Failures: 410
Kernel Version: 4.20.0-rc1-00016-ge0db606bc023
Machine Architecture: nds32
Hostname: greentime-d15-ae3xx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=Gy5E
-----END PGP SIGNATURE-----
Merge tag 'nds32-for-linus-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux
Pull nds32 updates from Greentime Hu:
- Perf support
- Power management support
- FPU support
- Hardware prefetcher support
- Build error fixed
- Performance enhancement
* tag 'nds32-for-linus-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux:
nds32: support hardware prefetcher
nds32: Fix the items of hwcap_str ordering issue.
math-emu/soft-fp.h: (_FP_ROUND_ZERO) cast 0 to void to fix warning
math-emu/op-2.h: Use statement expressions to prevent negative constant shift
nds32: support denormalized result through FP emulator
nds32: Support FP emulation
nds32: nds32 FPU port
nds32: Remove duplicated include from pm.c
nds32: Power management for nds32
nds32: Add document for NDS32 PMU.
nds32: Add perf call-graph support.
nds32: Perf porting
nds32: Fix bug in bitfield.h
nds32: Fix gcc 8.0 compiler option incompatible.
nds32: Fill all TLB entries with kernel image mapping
nds32: Remove the redundant assignment
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
- A bunch of new irqchip drivers (RDA8810PL, Madera, imx-irqsteer)
- Updates for new (and old) platforms (i.MX8MQ, F1C100s)
- A number of SPDX cleanups
- A workaround for a very broken GICv3 implementation
- A platform-msi fix
- Various cleanups
-----BEGIN PGP SIGNATURE-----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=1Mk9
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- A bunch of new irqchip drivers (RDA8810PL, Madera, imx-irqsteer)
- Updates for new (and old) platforms (i.MX8MQ, F1C100s)
- A number of SPDX cleanups
- A workaround for a very broken GICv3 implementation
- A platform-msi fix
- Various cleanups
If a hwspinlock is defined in device tree use it to protect
configuration registers.
Do not request for hwspinlock during the exti driver init since the
hwspinlock driver is not probed yet at that stage and the exti driver
does not support deferred probe.
Instead of this, postpone the hwspinlock request at the first time the
hwspinlock is actually needed.
Use the hwspin_trylock_raw() API which is the most appropriated here
Indeed:
- hwspin_lock_() calls are under spin_lock protection (chip_data->rlock
or gc->lock).
- the _timeout() API relies on jiffies count which won't work if IRQs
are disabled which is the case here (a large part of the IRQ setup is
done atomically (see irq/manage.c))
As a consequence implement the retry/timeout lock from here. And since
all of this is done atomically, reduce the timeout delay to 1 ms.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irqsteer block is a interrupt multiplexer/remapper found on the
i.MX8 line of SoCs.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Cirrus Logic Madera codecs (Cirrus Logic CS47L35/85/90/91 and WM1840)
are highly complex devices containing up to 7 programmable DSPs and many
other internal sources of interrupts plus a number of GPIOs that can be
used as interrupt inputs. The large number (>150) of internal interrupt
sources are managed by an on-board interrupt controller.
This driver provides the handling for the interrupt controller. As the
codec is accessed via regmap, we can make use of the generic IRQ
functionality from regmap to do most of the work. Only around half of
the possible interrupt source are currently of interest from the driver
so only this subset is defined. Others can be added in future if needed.
The KConfig options are not user-configurable because this driver is
mandatory so is automatically included when the parent MFD driver is
selected.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Go over the IRQ subsystem source code (including irqchip drivers) and
fix common typos in comments.
No change in functionality intended.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
The GPC node on i.MX8MQ can not claim to be compatible with the i.MX7D
GPC, as the power gating part has some significant differences. Thus we
can not rely on the irqchip being probed with the old compatible.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In case of error, the function of_io_request_and_map() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: d852e62ad6 ("irqchip: Add RDA8810PL interrupt driver")
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The -Wimplicit-fallthrough option requires that the /* fall through */
comment is placed in the 'case' statement that falls through, rather
than in the following one. Case seems to matter as well.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Access to GICR_WAKER is restricted on msm8996 SoC in Hypervisor.
Its been more than 2+ years of wait for this to be fixed, which has
no hopes to be fixed. This change was introduced for the "lead device"
on msm8996 platform. It looks like all publicly available msm8996 and
other Qualcomm SoCs have this implementation.
So add a quirk to not access this register on msm8996.
With this quirk MSM8996 can at least boot out of mainline,
which can help community to work with boards based on MSM8996 and other
SoCs with have this restrictions. This Quirk is based on device tree
compatible string.
Without this patch Qualcomm DB820c board reboots when GICR_WAKER
is accessed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds support to device tree based quirks based on
device tree compatible string.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds support for suniv Allwinner ARMv5 F1C100s SoC which has
stripped version of interrupt controller that found in A10/A13.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch moves IC specific register offsets to sun4i_irq_chip_data
struct in order to support different chips.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to support different chips, IC specific data should be hold in
a struct. This patch moves irq_base and irq_domain global variables to
struct.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make error messages more consistent by making sure each starts with
"%pOF:".
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: cphealy@gmail.com
Cc: l.stach@pengutronix.de
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Convert all instances of 1 << x to BIT(x) for consistency with other
kernel code.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: cphealy@gmail.com
Cc: l.stach@pengutronix.de
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move identical offset calculation code into a small helper function
and make use of it in the rest of the code.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: cphealy@gmail.com
Cc: l.stach@pengutronix.de
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Varaible 'reg' in imx_gpcv2_irq_set_wake() has no users. Remove it.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: cphealy@gmail.com
Cc: l.stach@pengutronix.de
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Simon Arlott <simon@arlott.org>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
WSR and RSR are too generic and collide with other macro definitions in
the kernel causing warnings in allmodconfig builds. Drop WSR and RSR
macros and WSR_* and RSR_* variants. Change get_sr and set_sr to
xtensa_get_sr and xtensa_set_sr. Fix up users.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
There are three sleep states in nds32:
suspend to idle,
suspend to standby,
suspend to ram
In suspend to ram, we use the 'standby' instruction to emulate
power management device to hang the system util wakeup source
send wakeup events to break the loop.
First, we push the general purpose registers and system registers
to stack. Second, we translate stack pointer to physical address
and store to memory to save the stack pointer. Third, after write
back and invalid the cache we hang in 'standby' intruction.
When wakeup source trigger wake up events, the loop will be break
and resume the system.
Signed-off-by: Nick Hu <nickhu@andestech.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
The devm_ioremap_resource() function never returns NULL, it returns
error pointers.
Fixes: 61ce8d8d8a ("irqchip/irq-mvebu-sei: Add new driver for Marvell SEI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20181013102246.GD16086@mwanda
Release, which has been through 10 rounds of review on mailing list.
We almost got the Acked-by/Reviewed-by of all patches except "Process
management and Signal", but all've been tested.
Here is the LTP-20180118 test report:
-----------------------------------------------
Total Tests: 1298
Total Skipped Tests: 281
Total Failures: 10
Kernel Version: 4.19.0+
Machine Architecture: csky
Hostname: buildroot
-----------------------------------------------
This patchset adds architecture support to Linux for C-SKY's 32-bit embedded
There are two ABI versions with several CPU cores in this patchset:
ABIv1: 610 (16-bit instruction, 32-bit data path, VIPT Cache ...)
ABIv2: 807 810 860 (16/32-bit variable length instruction, PIPT Cache,
SMP ...)
More information: http://en.c-sky.com
The development repo: https://github.com/c-sky/csky-linux
ABI Documentation: https://github.com/c-sky/csky-doc
Here is the pre-built cross compiler for fast test from our CI:
https://gitlab.com/c-sky/buildroot/-/jobs/101608095/artifacts/file/output/images/csky_toolchain_qemu_csky_ck807f_4.18_glibc_defconfig_482b221e52908be1c9b2ccb444255e1562bb7025.tar.xz
We use buildroot as our CI-test enviornment. "LTP, Lmbench ..."
will be tested for every commit. See here for more details:
https://gitlab.com/c-sky/buildroot/pipelines
We'll continouslly improve csky subsystem in future.
Changes in v10:
- Remove duplicated headers in asm/Kbuild and uapi/asm/Kbuild.
- Change to (__NR_arch_specific_syscall + 1) in unistd.h.
- Drop dword access for get_user_size patch.
- Involve the interrupt controller drivers after got Reviewed-by.
Changes in v9:
- Remove unused code in smp.c and use per_cpu for ipi_data.
- Fixup r15 register access in abiv1/alignment.c.
- Improve the changelog comment in commit-msg.
Changes in v8:
- Pass make allmodconfig.
- Implement abiv1 get_user_dword().
- Remove set_irq_mapping() used by driver in smp.c.
Changes in v7:
- Use checkpatch.pl to check all patches and fixup as possible.
- Remove github.com/c-sky print in bootup.
- Give a return in DMA_ATTR_NON_CONSISTENT in csky_dma_alloc_atomic().
- Remove the NSIGXXX in fpu.c and use force_sig_fault() in fpu.c.
- Remove irq.h and add it in asm/Kbuild.
- Use byteswap helpers in abiv1/bswapXi.c.
- Fixup arch_sync_dma() only with one page problem.
Changes in v6:
- use asm-generic/bitops/atomic.h for all in asm/bitops.h
- fix flush_cache_range and tlb_start_vma
- fix compile error with include linux/bug.h in cmpxchg.h
- improve the comment
Changes in v5:
- remove redundant smp_mb operations in spinlock.h
- add commit message for dt-bindings docs
- add CPUHP_AP_CSKY_TIMER_STARTING in hotplug.h for csky_mptimer
- add COMPILE_TEST for timer-gx6605s Kconfig
- seperate csky two interrupt controllers with 2 patches
- add MAINTAINERS patch for csky
- move IPI_IRQ into csky_mptimer, fixup irq_mapping problem
- coding convension
Changes in v4:
- cleanup defconfig
- use ksys_ in syscall.c
- remove wrong comment in vdso.c
- Use GENERIC_IRQ_MULTI_HANDLER
- optimize the memset.c
- fixup dts warnings
- remove big-endian in byteorder.h
Changes in v3:
dc560f1 csky: change to EM_CSKY 252 for elf.h
2ac3ddf csky: remove gx6605s.dts
af00b8c csky: add defconfig and qemu.dts
6c87efb csky: remove the deprecate name.
f6dda39 csky: add dt-bindings doc.
d9f02a8 csky: remove KERNEL_VERSION in upstream branch
7bd663c csky: Use kernel/dma/noncoherent.c
1544c09 csky: bugfix emmc hang up LINS-976
e963271 csky: cleanup include/asm/Kbuild
cd267ba csky: remove CSKY_DEBUG_INFO
78950da csky: remove dcache invalid.
13fe51d csky: remove csum_ipv6_magic(), use generic one.
a7372db csky: bugfix CK810 access twice error.
1bb7c69 csky: bugfix add gcc asm memory for barrier.
5ea3257 csky: add -msoft-float instead of -mfloat-abi=soft.
38b037d csky: bugfix losing cache flush range.
ab5e8c4 csky: Add ticket-spinlock and qrwlock support.
c9aaec5 csky: rename cskyksyms.c to libgcc_ksyms.c
28c5e48 csky: avoid the MB on failure: trylock
f929c97 csky: bugfix idly4 may cause exception.
09dc496 csky: Use GENERIC_ASHLDI3/ASHRDI3 etc
6ecc99d csky: optimize smp boot code.
16f50df csky: asm/bug.h simple implement.
0ba532a csky: csky asm/atomic.h added.
df66947 csky: asm/compat.h added
275a06f csky: String operations optimization
4c021dd csky: ck860 SMP memory barrier optimize
fc39c66 csky: Add wait/doze/stop
d005144 csky: add GENERIC_ALLOCATOR
4a10074 csky: bugfix cma failed for highmem.
9f2ca70 csky: CMA supported :)
53791f4 csky: optimize csky_dma_alloc_nonatomic
974676e csky: optimize the cpuinfo printf.
2538669 csky: bugfix make headers_install error.
1158d0c csky: prevent hard-float and vdsp instructions.
dc3c856 csky: increase Normal Memory to 1GB
6ee5932 csky: bugfix qemu mmu couldn't support 0xffffe000
1d7dfb8 csky: csky_dma_alloc_atomic added.
caf6610 csky: restruct the fixmap memory layout.
5a17eaa csky: use -Wa,-mcpu=ckxxxfv to the as.
4d51829 csky: use Kconfig.hz.
f3f88fa csky: BUGFIX add -mcpu=ck860f support
6192fd1 csky: support ck860 fpu.
7aa5e01 csky: BUGFIX add smp_mb before ldex.
15758e2 csky: BUGFIX tlbi couldn't handle ASID in another CPU core.
d69640d csky: enable tlbi.vas to flush one tlb entry
Changes in v2:
a29bfc8 csky: add pre_mmu_init, move misc mmu setup to mm/init.c
4eab702 csky: no need kmap for !VM_EXEC.
6770eec csky: Use TEE as the name of CPU Trusted Execution Enviornment.
a56c8c7 csky: update the cache flush api.
1a48a95 csky: add C-SKY Trust Zone.
b7a0a44 csky: use CONFIG_RAM_BASE as the same in memory of dts.
15adf81 csky: remove unused code.
35c0d97 csky: bugfix lost a cacheline flush when start isn't cacheline-aligned.
4e82c8d csky: use tlbi.alls for ck860 smp temporary.
ae7149e csky: bugfix use kmap_atomic() to prevent no mapped addr.
5538795 csky: bugfix user access in kernel space.
a7aa591 csky: add 16bit user space bkpt.
0de70ec csky: add sync.is for cmpxchg in SMP.
c5c08a1 csky: seperate sync.is and sync for SMP and Non-SMP.
dbbf4dc csky: use sync.is for ck860 mb().
f33f8da csky: rewrite the alignment implement.
68152c7 csky: bugfix alignment pt_regs error.
d618d43 csky: support set_affinity for irq balance in SMP
ebf86c9 csky: bugfix compile error without CONFIG_SMP.
8537eea csky: remove debug code.
4ebc051 csky: bugfix compile error with linux-4.9.56
75a938e csky: C-SKY SMP supported.
0eebc07 csky: use internal function for map_sg.
3d29751 csky: bugfix can't support highmem
b545d2a csky: bugfix r26 is the link reg for jsri_to_jsr.
9e3313a csky: bugfix sync tls for abiv1 in ptrace.
587a0d2 csky: use __NR_rt_sigreturn in asm-generic.
f562b46 csky: bugfix gpr_set & fpr_set
f57266f csky: bugfix fpu_fpe_helper excute mtcr mfcr.
c676669 csky: bugfix ave is default enable on reset.
d40d34d csky: remove unused sc_mask in sigcontext.h.
274b7a2 csky: redesign the signal's api
7501771 csky: bugfix forget restore usp.
923e2ca csky: re-struct the pt_regs for regset.
2a1e499 csky: fixup config.
ada81ec csky: bugfix abiv1 compile error.
e34acb9 csky: bugfix abiv1 couldn't support -mno-stack-size.
ec53560 csky: change irq map, reserve soft_irq&private_irq space.
c7576f7 csky: bugfix modpost warning with -mno-stack-size
c8ff9d4 csky: support csky mp timer alpha version.
deabaaf csky: update .gitignore.
574815c csky: bugfix compile error with abiv1 in 4.15
0b426a7 csky: bugfix format of cpu verion id.
083435f csky: irq-csky-v2 alpha init.
21209e5 csky: add .gitignore
73e19b4 csky: remove FMFS_FPU_REGS/FMTS_FPU_REGS
07e8fac csky: add fpu regset in ptrace.c
cac779d csky: add CSKY_VECIRQ_LEGENCY for SOC bug.
54bab1d csky: move usp into pt_regs.
b167422 csky: support regset for ptrace.
a098d4c csky: remove ARCH_WANT_IPC_PARSE_VERSION
fe61a84 csky: add timer-of support.
27702e2 csky: bugfix boot error.
ebe3edb csky: bugfix gx6605s boot failed - add __HEAD to head.section for head.S - move INIT_SECTION together to fix compile warning.
7138cae csky: coding convension for timer-nationalchip.c
fa7f9bb csky: use ffs instead of fls.
ddc9e81 csky: change to generic irq chip for irq-csky.c
e9be8b9 irqchip: add generic irq chip for irq-nationalchip
2ee83fe csky: add set_handle_irq(), ref from openrisc & arm.
74181d6 csky: use irq_domain_add_linear instead of leagcy.
fa45ae4 csky: bugfix setup stroge order for uncached.
eb8030f csky: add HIGHMEM config in Kconfig
4f983d4 csky: remove "default n" in Kconfig
2467575 csky: use asm-generic/signal.h
77438e5 csky: coding conventions for irq.c
2e4a2b4 csky: optimize the cache flush ops.
96e1c58 csky: add CONFIG_CPU_ASID_BITS.
9339666 csky: add cprcr() cpwcr() for abiv1
ff05be4 csky: add THREAD_SHIFT define in asm/page.h
52ab022 csky: add mfcr() mtcr() in asm/reg_ops.h
bdcd8f3 csky: revert back Kconfig select.
590c7e6 csky: bugfix compile error with CONFIG_AUDIT
1989292 csky: revert some back with cleanup unistd.h
f1454fe csky: cleanup unistd.h
5d2985f csky: cleanup Kconfig and Makefile.
423d97e csky: cancel subdirectories
cae2af4 csky: use asm-generic/fcntl.h
-----BEGIN PGP SIGNATURE-----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=kHer
-----END PGP SIGNATURE-----
Merge tag 'csky-for-linus-4.20' of https://github.com/c-sky/csky-linux
Pull C-SKY architecture port from Guo Ren:
"This contains the Linux port for C-SKY(csky) based on linux-4.19
Release, which has been through 10 rounds of review on mailing list.
More information:
http://en.c-sky.com
The development repo:
https://github.com/c-sky/csky-linux
ABI Documentation:
https://github.com/c-sky/csky-doc
Here is the pre-built cross compiler for fast test from our CI:
https://gitlab.com/c-sky/buildroot/-/jobs/101608095/artifacts/file/output/images/csky_toolchain_qemu_csky_ck807f_4.18_glibc_defconfig_482b221e52908be1c9b2ccb444255e1562bb7025.tar.xz
We use buildroot as our CI-test enviornment. "LTP, Lmbench ..." will
be tested for every commit. See here for more details:
https://gitlab.com/c-sky/buildroot/pipelines
We'll continouslly improve csky subsystem in future"
Arnd acks, and adds the following notes:
"I did a thorough review of the ABI, which as usual mainly consists of
spotting any files that don't use the asm-generic ABI itself, and
having it changed to it matches exactly what we do on other new
architectures.
I also looked at every other patch and commented on maybe half of them
where I saw something that did not quite seem right. Others have
reviewed specific patches in greater depth. I'm sure that one could
fine more of the minor details, but as long as they are not ABI
relevant, they can be fixed later.
The only patch that is part of the ABI and that nobody reviewed is the
signal handling. This is one of the areas I never worked on in much
detail. I did not see anything wrong with it, but I also don't know
what the problems with the other architectures are here, and we seem
to be hitting issues occasionally, and we never managed to generalize
this enough for new architectures to have a trivial implementation.
I was originally hoping that we could have the 64-bit time_t
interfaces ready in time to completely drop the 32-bit ones, but that
did not happen. We might still remove them in the next merge window
depending on whether the libc upstream people prefer to keep them or
not.
One more general comment: I think this may well be the last new CPU
architecture we ever add to the kernel. Both nds32 and c-sky are made
by companies that also work on risc-v, and generally speaking risc-v
seems to be killing off any of the minor licensable instruction set
projects, just like ARM has mostly killed off the custom
vendor-specific instruction sets already.
If we add another architecture in the future, it may instead be
something like the LLVM bitcode or WebAssembly, who knows?"
To which Geert Uytterhoeven pipes in about another architecture still in
the pipeline: Kalray MPPA.
* tag 'csky-for-linus-4.20' of https://github.com/c-sky/csky-linux: (24 commits)
dt-bindings: interrupt-controller: C-SKY APB intc
irqchip: add C-SKY APB bus interrupt controller
dt-bindings: interrupt-controller: C-SKY SMP intc
irqchip: add C-SKY SMP interrupt controller
MAINTAINERS: Add csky
dt-bindings: Add vendor prefix for csky
dt-bindings: csky CPU Bindings
csky: Misc headers
csky: SMP support
csky: Debug and Ptrace GDB
csky: User access
csky: Library functions
csky: ELF and module probe
csky: Atomic operations
csky: IRQ handling
csky: VDSO and rt_sigreturn
csky: Process management and Signal
csky: MMU and page table management
csky: Cache and TLB routines
csky: System Call
...
This patch set contains a lot (at least, for me) of improvements to the
RISC-V kernel port:
* The removal of some cacheinfo values that were bogus.
* On systems with F but without D the kernel will not show the F
extension to userspace, as it isn't actually supported.
* Support for futexes.
* Removal of some unused code.
* Cleanup of some menuconfig entries.
* Support for systems without a floating-point unit, and for building
kernels that will never use the floating-point unit.
* More fixes to the RV32I port, which regressed again. It's really time
to get this into a regression test somewhere so I stop breaking it.
Thanks to Zong for resurrecting it again!
* Various fixes that resulted from a year old review of our original
patch set that I finally got around to.
* Various improvements to SMP support, largely based around having
switched to logical hart numbering, as well as some interrupt
improvements. This one is in the same patch set as above, thanks to
Atish for sheparding everything though as my patch set was a bit of a
mess.
I'm pretty sure this is our largest patch set since the original kernel
contribution, and it's certainly the one with the most contributors.
While I don't have anything else I know I'm going to submit for the
merge window, I would be somewhat surprised if I didn't screw anything
up.
Thanks for the help, everyone!
-----BEGIN PGP SIGNATURE-----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=YL+A
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This patch set contains a lot (at least, for me) of improvements to
the RISC-V kernel port:
- The removal of some cacheinfo values that were bogus.
- On systems with F but without D the kernel will not show the F
extension to userspace, as it isn't actually supported.
- Support for futexes.
- Removal of some unused code.
- Cleanup of some menuconfig entries.
- Support for systems without a floating-point unit, and for building
kernels that will never use the floating-point unit.
- More fixes to the RV32I port, which regressed again. It's really
time to get this into a regression test somewhere so I stop
breaking it. Thanks to Zong for resurrecting it again!
- Various fixes that resulted from a year old review of our original
patch set that I finally got around to.
- Various improvements to SMP support, largely based around having
switched to logical hart numbering, as well as some interrupt
improvements. This one is in the same patch set as above, thanks to
Atish for sheparding everything though as my patch set was a bit of
a mess.
I'm pretty sure this is our largest patch set since the original
kernel contribution, and it's certainly the one with the most
contributors. While I don't have anything else I know I'm going to
submit for the merge window, I would be somewhat surprised if I didn't
screw anything up.
Thanks for the help, everyone!"
* tag 'riscv-for-linus-4.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits)
RISC-V: Cosmetic menuconfig changes
riscv: move GCC version check for ARCH_SUPPORTS_INT128 to Kconfig
RISC-V: remove the unused return_to_handler export
RISC-V: Add futex support.
RISC-V: Add FP register ptrace support for gdb.
RISC-V: Mask out the F extension on systems without D
RISC-V: Don't set cacheinfo.{physical_line_partition,attributes}
RISC-V: Show IPI stats
RISC-V: Show CPU ID and Hart ID separately in /proc/cpuinfo
RISC-V: Use Linux logical CPU number instead of hartid
RISC-V: Add logical CPU indexing for RISC-V
RISC-V: Use WRITE_ONCE instead of direct access
RISC-V: Use mmgrab()
RISC-V: Rename im_okay_therefore_i_am to found_boot_cpu
RISC-V: Rename riscv_of_processor_hart to riscv_of_processor_hartid
RISC-V: Provide a cleaner raw_smp_processor_id()
RISC-V: Disable preemption before enabling interrupts
RISC-V: Comment on the TLB flush in smp_callin()
RISC-V: Filter ISA and MMU values in cpuinfo
RISC-V: Don't set cacheinfo.{physical_line_partition,attributes}
...
The driver is for C-SKY APB bus interrupt controller. It's a simple
interrupt controller which use pending reg to detect the irq and use
enable/disable reg to mask/unmask interrupt sources.
A lot of SOCs based on C-SKY CPU use the interrupt controller as root
controller.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
The driver is for C-SKY SMP interrupt controller. It support 16
soft-irqs, 16 private-irqs, and 992 max external-irqs, a total of
1024 interrupts.
C-SKY CPU 807/810/860 SMP/non-SMP could use it.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Setup the cpu_logical_map during boot. Moreover, every SBI call
and PLIC context are based on the physical hartid. Use the logical
CPU to hartid mapping to pass correct hartid to respective functions.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It's a bit confusing exactly what this function does: it actually
returns the hartid of an OF processor node, failing with -1 on invalid
nodes. I've changed the name to _hartid() in order to make that a bit
more clear, as well as adding a comment.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
LPIs use the same priority value as other GIC interrupts.
Make the GIC default priority definition visible to ITS implementation
and use this same definition for LPI priorities.
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Multiple interrupts pending for a CPU is actually rare. Doing an
acknowledge loop does not give much better performance or even can
deteriorate them.
Do not loop when an interrupt has been acknowledged, just return
from interrupt and wait for another one to be raised.
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far the ICU only handled NSR interrupts through GICP. An SEI driver
provides an MSI domain through which it is possible to raise SEI, so
let's add SEI support to the ICU driver.
Handle the NSR probe function in a more generic way to support other
type of interrupts.
Each interrupt domain is a tree domain to avoid allocation the 207
entries each time.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is a cascaded interrupt controller in the AP806 GIC that collapses
SEIs (System Error Interrupt) coming from the AP and the CPs (through
the ICU).
The SEI handles up to 64 interrupts. The first 21 interrupts are wired
from the AP. The next 43 interrupts are from the CPs and are triggered
through MSI messages. To handle this complexity, the driver has to
declare to the upper layer: one IRQ domain for the wired interrupts,
one IRQ domain for the MSIs; and acts as a MSI controller ('parent')
by declaring an MSI domain.
Suggested-by: Haim Boot <hayim@marvell.com>
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ICU can handle several type of interrupt, each of them being handled
differently on AP side. On CP side, the ICU should be able to make the
distinction between each interrupt group by pointing to the right parent.
This is done through the introduction of new bindings, presenting the ICU
node as the parent of multiple ICU sub-nodes, each of them being an
interrupt type with a different interrupt parent. ICU interrupt 'clients'
now directly point to the right sub-node, avoiding the need for the extra
ICU_GRP_* parameter.
ICU subnodes are probed automatically with devm_platform_populate(). If
the node as no child, the probe function for NSRs will still be called
'manually' in order to preserve backward compatibility with DT using the
old binding.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
NSR (non-secure interrupts) are handled in the ICU driver like if there
was only this type of interrupt in the ICU. Change this behavior to
prepare the introduction of SEI (System Error Interrupts) support by
moving the NSR code in a separate function. This is done under the form
of a 'probe' function to ease future migration to NSR/SEI being platform
devices part of the ICU. The 'icu' structure is passed as driver data
and not as a parameter for the same reason.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rewrite a small section to clarify the reset operation of interrupts
already configured by ATF that we want to handle in the driver. This
will simplify the introduction of System Error Interrupts support.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_domain structure has an host_data pointer that just stores
private data. It is meant to not be touched by the IRQ core. However,
when it comes to MSI, the MSI layer adds its own private data there
with a structure that also has a host_data pointer.
Because this IRQ domain is an MSI domain, to access private data we
should do a d->host_data->host_data, also wrapped as
'platform_msi_get_host_data()'.
This bug was lying there silently because the 'icu' structure retrieved
this way was just called by dev_err(), only producing a
'(NULL device *):' output on the console.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The PDC irqchp can convert a falling edge or level low interrupt to a
rising edge or level high interrupt at the GIC. We just need to setup
the GIC correctly. Set up the interrupt type for the IRQ_TYPE_EDGE_BOTH
as IRQ_TYPE_EDGE_RISING at the GIC.
Fixes: f55c73aef8 ("irqchip/pdc: Add PDC interrupt controller for QCOM SoCs")
Reported-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the LPI tables have been reserved with the EFI reservation
mechanism, we assume that these tables are safe to use even
when we find the redistributors to have LPIs enabled at
boot time, meaning that kexec can now work with GICv3.
You're welcome.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Upon enabling a redistributor, let's register the allocated tables
with the EFI table that tracks the memory reservations.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If booting with LPIs enabled, all the redistributors must have the
exact same property table. No ifs, no buts.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If using a kdump kernel, and that we cannot disable LPIs to install
our own tables, let's switch to using the already allocated tables.
This means that we'll change some of the initial kernel's memory,
but at least we'll be able to have LPIs in this secondary kernel.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to cope with kexec and GICv3, let's try and spot when
we're booting with LPIs already enabled, and the tables already
programmed into the redistributors.
This code is currently guarded by a predicate that is always false,
meaning this is not functionnal just yet.
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We're currently only tracking the page allocated to contain the
property table by its struct page. In the future, it is going to
be convenient to track both PA and VA for that page instead. Let's
do that.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pending tables for the redistributors are currently allocated
one at a time as each CPU boots. This is causing some grief
for Linux/RT (allocation from within a CPU hotplug notifier is
frown upon).
Let's move this allocation to take place at init time, when we
only have a single CPU. It means we're allocating memory for CPUs
that are not online yet, but most system will boot all of their
CPUs anyway, so that's not completely wasted.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're going to reuse some pre-allocated memory for the property
table, split out the zeroing of that table into a separate function
for later use.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
LPI_PENDING_SZ is always used in conjunction with a max(), which doesn't
make much sense, since we're guaranteed that LPI_PENDING_SZ is already
aligned to 64K. Let's remove it.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently initialize the LPIs (and the ITS) fairly early, even
before the SMP support and the CPU interface. This is a bit odd
(as LPIs are not exactly crutial for the early boot process),
and is going to cause issues when reorganizing the probing code.
Let's move this initialization later.
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit fe8e93504c ("irqchip/gic-v3-its: Use full range of LPIs"), removes
the cap for lpi_id_bits, which causes the following warning to trigger on a
QDF2400 server:
WARNING: CPU: 0 PID: 0 at mm/page_alloc.c:4066 __alloc_pages_nodemask
...
Call trace:
__alloc_pages_nodemask+0x2d8/0x1188
alloc_pages_current+0x8c/0xd8
its_allocate_prop_table+0x5c/0xb8
its_init+0x220/0x3c0
gic_init_bases+0x250/0x380
gic_acpi_init+0x16c/0x2a4
In its_alloc_lpi_tables(), lpi_id_bits is 24 in QDF2400. The allocation in
allocate_prop_table() tries therefore to allocate 16M (order 12 if
pagesize=4k), which triggers the warning.
As said by MarcL
Capping lpi_id_bits at 16 (which is what we had before) is plenty,
will save a some memory, and gives some margin before we need to push
it up again.
Bring the upper limit of lpi_id_bits back to prevent
Fixes: fe8e93504c ("irqchip/gic-v3-its: Use full range of LPIs")
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jia He <jia.he@hxt-semitech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Olof Johansson <olof@lixom.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lkml.kernel.org/r/1535432006-2304-1-git-send-email-jia.he@hxt-semitech.com
Pull irq update from Thomas Gleixner:
"A small set of updats/fixes for the irq subsystem:
- Allow GICv3 interrupts to be configured as wake-up sources to
enable wakeup from suspend
- Make the error handling of the STM32 irqchip init function work
- A set of small cleanups and improvements"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Allow interrupt to be configured as wake-up sources
irqchip/tango: Set irq handler and data in one go
dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support
irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0
irqchip/stm32: Fix init error handling
irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP
Var "addr" type incorrect.
It have interrupt controler register address.
Type of void __iomem is correct.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
If an xtensa core provides an additional IRQ controller it should be
treated as a separate piece of hardware and be driven by an irqchip
driver.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Although GICv3 doesn't directly offers support for wake-up interrupts
and relies on external HW for this, it shouldn't prevent the driver
for such HW from doing it work.
Let's set the required flags on the irq_chip structures.
Reported-by: Lina Iyer <ilina@codeaurora.org>
Tested-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Replace the two separate calls for setting the irq handler and data with
a single irq_set_chained_handler_and_data() call.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This tag contains some major improvements to the RISC-V port, including
the necessary interrupt controller and timer support to actually make it
to userspace. Support for three devices has been added:
* Support for the ISA-mandated timers on RISC-V systems.
* Support for the ISA-mandated first-level interrupt controller on
RISC-V systems, which is handled as part of our core arch code because
it's very small and tightly tied to the ISA.
* Support for SiFive's platform-level interrupt controller, which talks
to the actual devices.
In addition to these new devices, there are a handful of cleanups all
over the RISC-V tree:
* Build fixes for various configurations
* A fix to the vDSO build's makefile so it respects CFLAGS.
* The addition of __lshrti3, a libgcc derived function necessary for
some 32-bit configurations.
* !SMP && PERF_EVENTS
* Cleanups to the arch code to remove the remnants of old versions of
the drivers that were just properly submitted.
* Some dead code from the timer driver, most of which wasn't ever
even compiled.
* Cleanups of some interrupt #defines, which are now local to the
interrupt handling code.
* Fixes to ptrace(), which while not being sufficient to fully make GDB
work are at least sufficient to get simple GDB tasks to work.
* Early printk support via RISC-V's architecturally mandated SBI console
device.
* A fix to our early debug trap handler to ensure it's always aligned.
These patches have all been through a fairly extensive review process,
but as this enables a whole pile of functionality (ie, userspace) I'm
confident we'll need to submit a few more patches. The only concrete
issues I know about are the sys_riscv_flush_icache patches, but as I
managed to screw those up on Friday I figured it'd be best to let them
bake another week.
This tag boots a Fedora root filesystem on QEMU's master branch for me,
and before this morning's rebase (from 4.18-rc8 to 4.18) it booted on
the HiFive Unleashed.
Thanks to Christoph Hellwig and the other guys at WD for getting the new
drivers in shape!
-----BEGIN PGP SIGNATURE-----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=PfnC
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains some major improvements to the RISC-V port, including
the necessary interrupt controller and timer support to actually make
it to userspace. Support for three devices has been added:
- the ISA-mandated timers on RISC-V systems.
- the ISA-mandated first-level interrupt controller on RISC-V
systems, which is handled as part of our core arch code because
it's very small and tightly tied to the ISA.
- SiFive's platform-level interrupt controller, which talks to the
actual devices.
In addition to these new devices, there are a handful of cleanups all
over the RISC-V tree:
- build fixes for various configurations:
* A fix to the vDSO build's makefile so it respects CFLAGS.
* The addition of __lshrti3, a libgcc derived function necessary
for some 32-bit configurations.
* !SMP && PERF_EVENTS
- Cleanups to the arch code to remove the remnants of old versions of
the drivers that were just properly submitted.
* Some dead code from the timer driver, most of which wasn't ever
even compiled.
* Cleanups of some interrupt #defines, which are now local to the
interrupt handling code.
- Fixes to ptrace(), which while not being sufficient to fully make
GDB work are at least sufficient to get simple GDB tasks to work.
- Early printk support via RISC-V's architecturally mandated SBI
console device.
- A fix to our early debug trap handler to ensure it's always
aligned.
These patches have all been through a fairly extensive review process,
but as this enables a whole pile of functionality (ie, userspace) I'm
confident we'll need to submit a few more patches. The only concrete
issues I know about are the sys_riscv_flush_icache patches, but as I
managed to screw those up on Friday I figured it'd be best to let them
bake another week.
This tag boots a Fedora root filesystem on QEMU's master branch for
me, and before this morning's rebase (from 4.18-rc8 to 4.18) it booted
on the HiFive Unleashed.
Thanks to Christoph Hellwig and the other guys at WD for getting the
new drivers in shape!"
* tag 'riscv-for-linus-4.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
dt-bindings: interrupt-controller: SiFive Plaform Level Interrupt Controller
dt-bindings: interrupt-controller: RISC-V local interrupt controller
RISC-V: Fix !CONFIG_SMP compilation error
irqchip: add a SiFive PLIC driver
RISC-V: Add the directive for alignment of stvec's value
clocksource: new RISC-V SBI timer driver
RISC-V: implement low-level interrupt handling
RISC-V: add a definition for the SIE SEIE bit
RISC-V: remove INTERRUPT_CAUSE_* defines from asm/irq.h
RISC-V: simplify software interrupt / IPI code
RISC-V: remove timer leftovers
RISC-V: Add early printk support via the SBI console
RISC-V: Don't increment sepc after breakpoint.
RISC-V: implement __lshrti3.
RISC-V: Use KBUILD_CFLAGS instead of KCFLAGS when building the vDSO
Add a driver for the SiFive implementation of the RISC-V Platform Level
Interrupt Controller (PLIC). The PLIC connects global interrupt sources
to the local interrupt controller on each hart.
This driver is based on the driver in the RISC-V tree from Palmer Dabbelt,
but has been almost entirely rewritten since, and includes many fixes
from Atish Patra.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
[Binding update by Palmer]
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
irq_data->hwirq is unsigned long. This fixes GCC warning:
drivers/irqchip/irq-s3c24xx.c: In function 's3c_irqext0_type':
drivers/irqchip/irq-s3c24xx.c:253:19: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if ((data->hwirq >= 0) && (data->hwirq <= 3)) {
^~
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If there are any errors in stm32_exti_host_init() then it leads to a
NULL dereference in the callers. The function should clean up after
itself.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When compiling bmips with SMP disabled, the build fails with:
drivers/irqchip/irq-bcm7038-l1.o: In function `bcm7038_l1_cpu_offline':
drivers/irqchip/irq-bcm7038-l1.c:242: undefined reference to `irq_set_affinity_locked'
make[5]: *** [vmlinux] Error 1
Fix this by adding and setting bcm7038_l1_cpu_offline only when actually
compiling for SMP. It wouldn't have been used anyway, as it requires
CPU_HOTPLUG, which in turn requires SMP.
Fixes: 34c535793b ("irqchip/bcm7038-l1: Implement irq_cpu_offline() callback")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- GICv3 ITS LPI allocation revamp
- GICv3 support for hypervisor-enforced LPI range
- GICv3 ITS conversion to raw spinlock
-----BEGIN PGP SIGNATURE-----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=gKw8
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- GICv3 ITS LPI allocation revamp
- GICv3 support for hypervisor-enforced LPI range
- GICv3 ITS conversion to raw spinlock
The its_lock lock is held while a new device is added to the list and
during setup while the CPU is booted. Even on -RT the CPU-bootup is
performed with disabled interrupts.
Make its_lock a raw_spin_lock_t.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Allocating a minimum of 32 LPIs per PCI device, let's reduce it to
be just 1, as most devices do not need that many interrupts.
We still have to special-case DevID 0, as there is plenty of broken
HW around where the PCI RID is not presented as a DevID to the ITS,
and all the devices are presented as DevID 0. In this case, we keep
the 32 minimal allocation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The interrupt controller of the JZ4725B works the same way as the other
JZ SoCs from Ingenic; so we just add a new compatible string.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch fixes a datasheet issue, in the draft version the "exti0"
was not connected whereas is it.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A recent extension to the GIC architecture allows a hypervisor to
arbitrarily reduce the number of LPIs available to a guest, no
matter what the GIC says about the valid range of IntIDs.
Let's factor in this information when computing the number of
available LPIs
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of exposing the GIC distributor IntID field in the rdist
structure that is passed to the ITS, let's replace it with a
copy of the whole GICD_TYPER register. We are going to need
some of this information at a later time.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At the moment, the core ITS driver imposes the allocation to be
in chunks of 32. As we want to relax this on a per bus basis, let's
move the the the allocation constraints to each bus.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we used to represent the LPI range using a bitmap, we were reducing
the number of LPIs to at most 64k in order to preserve memory.
With our new allocator, there is no such need, as dealing with 2^16
or 2^32 LPIs takes the same amount of memory.
So let's use the number of IntID bits reported by the GIC instead of
an arbitrary limit.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Our current LPI allocator relies on a bitmap, each bit representing
a chunk of 32 LPIs, meaning that each device gets allocated LPIs
in multiple of 32. It served us well so far, but new use cases now
require much more finer grain allocations, down the the individual
LPI.
Given the size of the IntID space (up to 32bit), it isn't practical
to continue using a bitmap, so let's use a different data structure
altogether.
We switch to a list, where each element represent a contiguous range
of LPIs. On allocation, we simply grab the first group big enough to
satisfy the allocation, and substract what we need from it. If the
group becomes empty, we just remove it. On freeing interrupts, we
insert a new group of interrupt in the list, sort it and fuse the
adjacent groups.
This makes freeing interrupt much more expensive than allocating
them (an unusual behaviour), but that's fine as long as we consider
that freeing interrupts is an extremely rare event.
We still allocate interrupts in blocks of 32 for the time being,
but subsequent patches will relax this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enabling LPIs was made a lot stricter recently, by checking that they are
disabled before enabling them. By doing so, the CPU hotplug case was missed
altogether, which leaves LPIs enabled on hotplug off (expecting the CPU to
eventually come back), and won't write a different value anyway on hotplug
on.
So skip that check if that particular case is detected
Fixes: 6eb486b66a ("irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling")
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lkml.kernel.org/r/20180622095254.5906-8-marc.zyngier@arm.com
Similarily to the SYNC operation, it must be verified that the VPE
targetted by a VLPI is backed by a valid collection in the GIC driver data
structures.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-7-marc.zyngier@arm.com
It is possible, under obscure circumstances, to convince the ITS driver to
emit a SYNC operation that targets a collection that is not bound to any
redistributor (and the target_address field is zero) because the
corresponding CPU has not been seen yet (the system has been booted with
max_cpus="something small").
If the ITS is using the linear CPU number as the target, this is not a big
deal, as we just end-up issuing a SYNC to CPU0. But if the ITS requires the
physical address of the redistributor (with GITS_TYPER.PTA==1), we end-up
asking the ITS to write to the physical address zero, which is not exactly
a good idea (there has been report of the ITS locking up). This should of
course never happen, but hey, this is SW...
In order to avoid the above disaster, let's track which collections have
been actually initialized, and let's not generate a SYNC if the collection
hasn't been properly bound to a redistributor. Take this opportunity to
spit our a warning, in the hope that someone may report the issue if it
arrises again.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-6-marc.zyngier@arm.com
On a NUMA system, if an ITS is local to an offline node, the ITS driver may
pick an offline CPU to bind the LPI. In this case, pick an online CPU (and
the first one will do).
But on some systems, binding an LPI to non-local node CPU may cause
deadlock (see Cavium erratum 23144). In this case, just fail the activate
and return an error code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180622095254.5906-5-marc.zyngier@arm.com
On failing to allocate the required SPIs, the actual number of interrupts
should be freed and not its log2 value.
Fixes: de337ee301 ("irqchip/gic-v2m: Add PCI Multi-MSI support")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-4-marc.zyngier@arm.com
The ls-scfs-msi driver is not dealing with the effective affinity
as it should. Let's fix that, and make it clear that the effective
affinity is restricted to a single CPU. Also prevent the driver from
messing with the internals of the affinity setting infrastructure.
Reported-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-3-marc.zyngier@arm.com
A CONFIG_SMP=n build emits a harmless compile-time warning:
drivers/irqchip/irq-stm32-exti.c:495:12: error: 'stm32_exti_h_set_affinity' defined but not used [-Werror=unused-function]
The #ifdef is inconsistent here, and it's better to use an IS_ENABLED() check
that lets the compiler silently drop that function.
Fixes: 927abfc446 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lkml.kernel.org/r/20180605114347.1347128-1-arnd@arndb.de
This patch adds suspend/resume feature for exti hierarchy domain.
-suspend function sets wake_active into imr of each banks
-resume function restores the mask_cache interrupt into
imr of each banks
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Exti controller has been differently integrated on stm32mp1 SoC.
A parent irq has only one external interrupt. A hierachy domain could
be used. Handlers are call by parent, each parent interrupt could be
masked and unmasked according to the needs.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch prepares functions which could be reused by
next variant of stm32 exti controller.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds host and driver data structures to support
different stm32 exti controllers with variants.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds suspend feature.
-Use default irq_set_wake function to store wakeup request.
-Suspend function set wake_active into imr of each bank
and save rising/falling trigger registers.
-Resume function restore the mask_cache interrupt into
imr of each bank and restore rising/falling trigger registers.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds support of rising/falling pending registers.
Falling pending register (fpr) is needed for next revision.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-WARNING: struct irq_domain_ops should normally be const
-CHECK: Alignment should match open parenthesis
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- In stm32_exti_alloc function, discards irq_domain_set_info
with handle_simple_irq. This overwrite the setting defined while init
of generic chips. Exti controller manages edge irq type.
- Removes acking in chained irq handler as this is done by
irq_chip itself inside handle_edge_irq
- removes unneeded irq_domain_ops.xlate callback
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Meson-AXG SoC uses the same GPIO interrupt controller IP block as the other
Meson SoCs. A total of 100 pins can be spied on, which is the sum of:
- 255:100 Undefined(no interrupt)
- 99:84, 16 pins on bank GPIOY
- 83:61, 23 pins on bank GPIOX
- 60:40, 21 pins on bank GPIOA
- 39:25, 15 pins on bank BOOT
- 24:14, 11 pins on bank GPIOZ
- 13:0 , 14 pins in the AO domain
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
You would hope that if you have a GICv3 in your system, you'd use the ITS,
as it provides a large interrupt ID space and device isolation. Sadly,
some SoC integrations are less than perfect, and the ITS is not usesable on
those.
The only solution for these systems is to use the MBI interface, and
rely on a very small number of possible vectors.
This patch thus adds minimal support for PCI/MSI on top of the GICv3
MBI driver. Please don't use it if you can avoid it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-9-marc.zyngier@arm.com
GICv3 offers the possibility to signal SPIs using a pair of doorbells
(SETPI, CLRSPI) under the name of Message Based Interrupts (MBI).
They can be used as either traditional (edge) MSIs, or the more exotic
level-triggered flavour.
Let's implement support for platform MSI, which is the original intent
for this feature.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-8-marc.zyngier@arm.com
As we're about to introduce MSI domains based on top of the GICv3
domain, we must make sure nothing the new domains do not alias
with the core domain.
So let's tag that core domain with the DOMAIN_BUS_WIRED attribute,
ensuring it gets picked up by other drivers that use irq_find_host().
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-7-marc.zyngier@arm.com
The ICU and GICP drivers are using an ugly side-band mechanism to
find out about the "clear" doorbell when using level interrupts.
Let's convert it to level-triggered MSIs, which result in a nice
cleanup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-4-marc.zyngier@arm.com
When the interrupts for a combiner span multiple registers it must be
checked if any interrupts have been asserted on each register before
checking for spurious interrupts.
Checking each register seperately leads to false positive warnings.
[ tglx: Massaged changelog ]
Fixes: f20cc9b00c ("irqchip/qcom: Add IRQ combiner driver")
Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: timur@codeaurora.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1525184090-26143-1-git-send-email-agustinv@codeaurora.org
These updates come with:
- OF_IOMMU support for the Rockchip iommu driver so that it can
use generic DT bindings
- Rework of locking in the AMD IOMMU interrupt remapping code to
make it work better in RT kernels
- Support for improved iotlb flushing in the AMD IOMMU driver
- Support for 52-bit physical and virtual addressing in the
ARM-SMMU
- Various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJazi2BAAoJECvwRC2XARrjYVwP/AyXK7CjRvaiHFopIUO0WpwY
V3GiKrODtSNHqPSKuFnqIssIhxZPw/SKFz6E/pe08pZ/pxHYTxeTL78Wz7D1+4Sp
n0YokSM5qLb660OTQVnyKNCku8cEMCb9hkQ/75SFgwcILQYF93cZBDIdBn93OKVO
6xAOE+tqd8Daulnk0YpdiCTFTJPzYHPl6B7scoUav26uaKxWeMJxeYe+EXC+4WQG
U1u/jDiVXyllzGgRqqfrmO4L2acmsK8HL97hD4+m1URJKDlb8ho6xwaRThFZWqXS
SbrYnvH0ruWGrLiQKmVUssw8FqbcXCzq3236g2O8jE4jqWSm70twg+q31iMjwD7v
bwsJGMkk7aLrquv9Zpaylpf8tRECk5bjhTFC2zB0pdum5XLx47j0IHKWMLPYhkCz
E0pBefvuhoSTbt/5X0urSRzH2Hk4ljEsM+QjlfH8SN3ALTljFjay607wbxC7t35M
LEL5AuNsDDBddoJIi9D13CdJEZa4lps8dbpB8m40lQVvmiLPLcKraaG0RfKQ397T
wsxhsDOQYM2FCwfUP3n8RTsMKRIp/UVkKY+2G7AsKofciSeulK6nDbrV7jFnitx4
vTxbRgpNejJpqzKZG/W9lCGWk1BhmQK/Cbu6JW5IA4+ew9omWkFp61U6rtc645Te
6cNEYBiMz/RZIiC2b18J
=kte5
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- OF_IOMMU support for the Rockchip iommu driver so that it can use
generic DT bindings
- rework of locking in the AMD IOMMU interrupt remapping code to make
it work better in RT kernels
- support for improved iotlb flushing in the AMD IOMMU driver
- support for 52-bit physical and virtual addressing in the ARM-SMMU
- various other small fixes and cleanups
* tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (53 commits)
iommu/io-pgtable-arm: Avoid warning with 32-bit phys_addr_t
iommu/rockchip: Support sharing IOMMU between masters
iommu/rockchip: Add runtime PM support
iommu/rockchip: Fix error handling in init
iommu/rockchip: Use OF_IOMMU to attach devices automatically
iommu/rockchip: Use IOMMU device for dma mapping operations
dt-bindings: iommu/rockchip: Add clock property
iommu/rockchip: Control clocks needed to access the IOMMU
iommu/rockchip: Fix TLB flush of secondary IOMMUs
iommu/rockchip: Use iopoll helpers to wait for hardware
iommu/rockchip: Fix error handling in attach
iommu/rockchip: Request irqs in rk_iommu_probe()
iommu/rockchip: Fix error handling in probe
iommu/rockchip: Prohibit unbind and remove
iommu/amd: Return proper error code in irq_remapping_alloc()
iommu/amd: Make amd_iommu_devtable_lock a spin_lock
iommu/amd: Drop the lock while allocating new irq remap table
iommu/amd: Factor out setting the remap table for a devid
iommu/amd: Use `table' instead `irt' as variable name in amd_iommu_update_ga()
iommu/amd: Remove the special case from alloc_irq_table()
...
Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs. 91k
remvoed), thanks to finally being able to delete the IRDA drivers and
networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful of
new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSnAA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn60ACgxKvU/5XBP14hBkBpAcD0Q43OHe0AniEti65M
Kw03GWK3NNM3pzk49BjZ
=sj3K
-----END PGP SIGNATURE-----
Merge tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs.
91k remvoed), thanks to finally being able to delete the IRDA drivers
and networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful
of new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (579 commits)
staging: rtl8723bs: Remove yield call, replace with cond_resched()
staging: rtl8723bs: Replace yield() call with cond_resched()
staging: rtl8723bs: Remove unecessary newlines from 'odm.h'.
staging: rtl8723bs: Rework 'struct _ODM_Phy_Status_Info_' coding style.
staging: rtl8723bs: Rework 'struct _ODM_Per_Pkt_Info_' coding style.
staging: rtl8723bs: Replace NULL pointer comparison with '!'.
staging: rtl8723bs: Factor out rtl8723bs_recv_tasklet() sections.
staging: rtl8723bs: Fix function signature that goes over 80 characters.
staging: rtl8723bs: Fix lines too long in update_recvframe_attrib().
staging: rtl8723bs: Remove unnecessary blank lines in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Change camel case to snake case in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Add missing braces in else statement.
staging: rtl8723bs: Add spaces around ternary operators.
staging: rtl8723bs: Fix lines with trailing open parentheses.
staging: rtl8723bs: Remove unnecessary length #define's.
staging: rtl8723bs: Fix IEEE80211 authentication algorithm constants.
staging: rtl8723bs: Fix alignment in rtw_wx_set_auth().
staging: rtl8723bs: Remove braces from single statement conditionals.
staging: rtl8723bs: Remove unecessary braces from switch statement.
staging: rtl8723bs: Fix newlines in rtw_wx_set_auth().
...
Pull irq updates from Thomas Gleixner:
"The usual pile of boring changes:
- Consolidate tasklet functions to share code instead of duplicating
it
- The first step for making the low level entry handler management on
multi-platform kernels generic
- A new sysfs file which allows to retrieve the wakeup state of
interrupts.
- Ensure that the interrupt thread follows the effective affinity and
not the programmed affinity to avoid cross core wakeups.
- Two new interrupt controller drivers (Microsemi Ocelot and Qualcomm
PDC)
- Fix the wakeup path clock handling for Reneasas interrupt chips.
- Rework the boot time register reset for ARM GIC-V2/3
- Better suspend/resume support for ARM GIV-V3/ITS
- Add missing locking to the ARM GIC set_type() callback
- Small fixes for the irq simulator code
- SPDX identifiers for the irq core code and removal of boiler plate
- Small cleanups all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
openrisc: Set CONFIG_MULTI_IRQ_HANDLER
arm64: Set CONFIG_MULTI_IRQ_HANDLER
genirq: Make GENERIC_IRQ_MULTI_HANDLER depend on !MULTI_IRQ_HANDLER
irqchip/gic: Take lock when updating irq type
irqchip/gic: Update supports_deactivate static key to modern api
irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling
irqchip: Add a driver for the Microsemi Ocelot controller
dt-bindings: interrupt-controller: Add binding for the Microsemi Ocelot interrupt controller
irqchip/gic-v3: Probe for SCR_EL3 being clear before resetting AP0Rn
irqchip/gic-v3: Don't try to reset AP0Rn
irqchip/gic-v3: Do not check trigger configuration of partitionned LPIs
genirq: Remove license boilerplate/references
genirq: Add missing SPDX identifiers
genirq/matrix: Cleanup SPDX identifier
genirq: Cleanup top of file comments
genirq: Pass desc to __irq_free instead of irq number
irqchip/gic-v3: Loudly complain about the use of IRQ_TYPE_NONE
irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE
RISC-V: Move to the new GENERIC_IRQ_MULTI_HANDLER handler
genirq: Add CONFIG_GENERIC_IRQ_MULTI_HANDLER
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
driver and timer driver), which has been through 7 rounds of review on mailing
list.
It is able to boot to shell and passes most LTP-2017 testsuites in nds32 AE3XX
platform.
Total Tests: 1901
Total Skipped Tests: 618
Total Failures: 78
Copied below is the ChangeLog that contains the history of this patch set:
Changes in v7:
- Update cpu binding document to add "andestech,nds32v3" as fallback
- Remove unnecessary configs of arch/nds32/Kconfig
- Use GENERIC_CALIBRATE_DELAY
- Add more help texts for minimum CPU type config
- Update defconfig because of Kconfig changed and bug fixed
- Move early_trap_init() declaration to nds32.h
- Refine dma.c
- Remove apply_relocate() in module.c and include <linux/moduleloader.h> to catch it
- Add do_kernel_restart() in machine_restart()
- Clean up setup.c to remove CONFIG_VGA_CONSOLE and some extern declaration functions
- Add negative dependency for VGA_CONSOLE on nds32
- Refine ptrace.c and arch/nds32/include/asm/ptrace.h
- Refine syscall restart flow and arch/nds32/kernel/signal.c
- Fix a bug in VDSO
- Remove the handling for kernel code unaligned accessing
- Add a description for unaligned access handling in git commit message.
- Rebase to v4.16-rc1
- Replace ACCESS_ONCE with READ_ONCE
- Replace atomic_long_dec(&mm->nr_ptes) with mm_dec_nr_ptes(mm)
- Remove print_symbol(%s) with printk(%pS)
- Add bpf_perf_event.h
- Remove init_stack and init_thread_info
Changes in v6:
- Refine naming for atl2c
- Refine ae3xx.dts
- Remove CONFIG_TIMER_ATCPIT100 in defconfig
- Refine elf.h
- Fix a vdso bug
- Separate arch patchset and timer patchset
- To select TIMER_OF in drivers/clocksource/Kconfig instead of arch/nds32/Kconfig
Changes in v5:
- Remove __NR__llseek and sys_mmap()
- Add a comment to explain that we don't have clocksource cycle counter in the CPU
- Add volatile in iounmap()
- Fix typo Featuretures to Features
- Replace CPU_CACHE_NONALIASING with !CPU_CACHE_ALIASING
- Fix a endian bug when we try to get val = of_get_property(cpu,"clock-frequency", NULL)
- Add screen_info to fix the building error when CONFIG_ VGA_CONSOLE is enabled
- Remove unnecessary msync()
- Add depends on !64BIT || BROKEN for faraday Kconfig because the descriptor only supports 32bit
- Add atl2c binding document
- Remove unnecessary include headers
- Fix a vector table bug. It placed wrong vector handlers for 2 exceptions.
- Fix a vdso bug. It may encounter TLB multi-hit exception because we accidently set it as a global page.
- Add proper isb and barrier after some cache operations
- Fix a bug in system call restart flow. $r0 ~ $r5 does not be recovered before restarting system call
- Fix the build errors for OpenRISC and SPARC because io.h changed.
- Update ae3xx.dts to support atl2c.
Changes in v4:
- Add atcpit100 timer driver due to it include vdso implementations and sent
them together with nds32 may help reviewer to review.
- Update ae3xx.dts for atcpit100 clock setting and remove vdso settings.
- To get cycle counter register by timer driver instead of dts.
- Use "depends on NDS32 || COMPILE_TEST" in atcpit100 driver because it is needed for nds32 vdso
- Update defconfig becasue kconfig rename from CONFIG_CLKSRC_ATCPIT100 to CONFIG_TIMER_ATCPIT100
- Remove ag101p.dts because we are not yet ready for ag101p platform.
- Update copyright style to SPDX-License-Identifier
- Include <linux/uaccess.h> instead of <asm/uaccess.h>
- Add local_irq_save()/local_irq_restore() to protect SR_TLB_VPN in update_mmu_cache().
- Update cpu_dcache_inval_all implementation to make sure all level cache are writeback.
Changes in v3:
- Use arch's io.h instead of generic one
- Add andestech-boards binding document
- Update nds32/cpus.txt binding document
- Remove atcpit100 timer drivers
- Select NO_BOOTMEM and delete HAVE_MEMBLOCK_NODE_MAP
- make CPU_BIG_ENDIAN and CPU_LITTLE_ENDIAN are dependent
- Add cpu type to select HWZOL/CPU_CACHE_ALIASING
- Change CPU_CACHE_NONALIASING to CPU_CACHE_ALIASING
- Remove bootarg from device tree script
- Update ag101p.dts and ae3xx.dts for correct board name.
- Clear and simplify defconfig
- Implement L2C_R_REG/ L2C_W_REG with readl/writel instead of __raw_readl/__raw_writel for endian save
- Remove early_init_dt_add_memory_arch/early_init_dt_alloc_memory_arch to use the generic ones
- Refine devicetree.c
- Fix bug https://lkml.kernel.org/r/1499782590-31366-1-git-send-ema...
- Refine irqchip/irq-ativic32.c implementations
- Add COMPILE_TEST in drivers/net/ethernet/faraday/Kconfig
- Refine cache operations
- Add CONFIG_HW_SUPPORT_UNALIGNMENT_ACCESS
- Fix ZERO_PAGE define
- Remove SA_RESTORER
- Remove uapi/asm/signal.h
- Redefine user_pt_regs
- Remove spinlock.h
- Remove __ARCH_WANT_RENAMEAT and __ARCH_WANT_SYSCALL_OFF_T from unistd.h
- Remove set_fs(USER_DS) because flush_old_exec() will do this setting
- Replace in_atomic() with faulthandler_disabled()
- Add barrier.h
- Select COMMON_CLK
- Add clk_pll in dts
- Add of_clk_init() in arch/nds32/kernel/time.c
Changes in v2:
- Set GENERIC_CALIBRATE_DELAY default n
- Add earlycon support
- Remove earlyprintk
- Add CPU_BIG_ENDIAN, CPU_LITTLE_ENDIAN support
- Refine unalignment access exception handler
- Add VMSPLIT support
- Use only one defconfig
- Change interrupt-cells from 2 to 1
- Refine andestech cpu names in bindings/nds32/cpus.txt
- Get clock frequency in dts because fpga bitmap doesn't include this feature
- Update MAINTAINERS for bindings
- Remove unused configs in Kconfig
- Refine device tree scripts
- Refine coding style
- Use generic ioremap_nocache
- Remove L2CC_PA_BASE define and its codes in head.S. It will be moved to bootloader.
- Set PHYS_OFFSET to 0x0 instead of CONFIG_MEMORY_START
- Remove unused macros
- Simplify cpu_cache_* API
- Change __asm__ __volatile__ to asm volatile
- Refine uaccess.h
- Remove unused/deprecated syscall
- Use generic posix_types.h
- Remove arch_trace_hardirqs_on/arch_trace_hardirqs_off
- Fix bug of restart syscall
- Refine syscall implementations
- Use IS_ENABLED to replace ifdef as possible
- Remove device_initcall(nds32_device_probe)
- Refine vdso implementations
- Refine copy_from_user()/copy_to_user()/clear_user()/get_user()/memmove()/memcpy()
- Refine ioremap.c
- Refine irq-ativic32.c
- Fix a bug of earlycon.c
- Export ioremap_nocache/ioremap_uc/ioremap_wc/ioremap_wt
- Add atcpit100 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)
iQIcBAABAgAGBQJawZ28AAoJEHfB0l0b2JxExKYQAJ7btaPeIplIndrphlTQkfzW
d1AhVBhwAlvqsOcFf+kwVIqOnfcLCtzVvgc63qc6mAroDZKcd+uuqOtkC801b33i
jxcfSX802PciT3VhE8xz9OWFY9D3in/UCBhGe2OvY/cD/eC34gZhUqJhML/ioR5q
DNPvua6lgYIN9VrFds19MjRzl7RwDBqNccQoFTXWc9Hl1Vs0YdKdbkOz0IWNtoLQ
crP0v/UuHMC++WdU+MvDIEFqNVuXikg/NA+odPIbp3eF3xcmQBM0blWAi37eOKFo
rzTw7TKtL8xObjvhyzx3aYFKPpLBfuYwk8onoZlthlqcwFClZy4lzdDdDxJhKiJ6
5hilzCSqEWXB9osQsrWgAuK1rNRvroChIp6/rcdGAq33mTPLVydx7hSKELhE7wuN
UUaiJSSNRG1ZrR8tkccQpaRBjJ/gfXWGC3ys723oWz8A4bDzMkvZVzdOGOEZ+CsI
w4HKNHLeY50wztV6dDSiVPhvUXQjBH9qd2zVHlutbfulPI/XNkGRfWpEGVT1zD4y
pO3aHVJfsv+8aeyVBcXyN74O34a9HYa7811v7V5RI+uftdPhkzOwxuMQVMMJPe3s
4u4NglP7fekeWyDGCXFKOGoVOuCAUPHuzBUCFjL/cStHjrkBGVQvL1I925sJNabu
IatFh62x8Ez4m2hIf5fg
=J/YF
-----END PGP SIGNATURE-----
Merge tag 'nds32-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux
Pull nds32 architecture support from Greentime Hu:
"This contains the core nds32 Linux port (including interrupt
controller driver and timer driver), which has been through seven
rounds of review on mailing list.
It is able to boot to shell and passes most LTP-2017 testsuites in
nds32 AE3XX platform:
Total Tests: 1901
Total Skipped Tests: 618
Total Failures: 78"
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
* tag 'nds32-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux: (44 commits)
nds32: To use the generic dump_stack()
nds32: fix building failed if using elf toolchain.
nios2: add ioremap_nocache declaration before include asm-generic/io.h.
nds32: fix building failed if using older version gcc.
dt-bindings: timer: Add andestech atcpit100 timer binding doc
clocksource/drivers/atcpit100: VDSO support
clocksource/drivers/atcpit100: Add andestech atcpit100 timer
net: faraday add nds32 support.
irqchip: Andestech Internal Vector Interrupt Controller driver
dt-bindings: interrupt-controller: Andestech Internal Vector Interrupt Controller
dt-bindings: nds32 SoC Bindings
dt-bindings: nds32 L2 cache controller Bindings
dt-bindings: nds32 CPU Bindings
MAINTAINERS: Add nds32
nds32: Build infrastructure
nds32: defconfig
nds32: Miscellaneous header files
nds32: Device tree support
nds32: Generic timers support
nds32: Loadable modules
...
Most MMIO GIC register accesses use a 1-hot bit scheme that
avoids requiring any form of locking. This isn't true for the
GICD_ICFGRn registers, which require a RMW sequence.
Unfortunately, we seem to be missing a lock for these particular
accesses, which could result in a race condition if changing the
trigger type on any two interrupts within the same set of 16
interrupts (and thus controlled by the same CFGR register).
Introduce a private lock in the GIC common comde for this
particular case, making it cover both GIC implementations
in one go.
Cc: stable@vger.kernel.org
Signed-off-by: Aniruddha Banerjee <aniruddhab@nvidia.com>
[maz: updated changelog]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
No changes in semantics -- key init is true; replace
static_key_slow_dec with static_branch_disable
static_key_true with static_branch_likely
The first is because we never actually do any couterpart incs,
thus there is really no reference counting semantics going on.
Use the more proper static_branch_disable() construct.
Also added a '_key' suffix to supports_deactivate, for better
self documentation.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Booting with GICR_CTLR.EnableLPI=1 is usually a bad idea, and may
result in subtle memory corruption. Detecting this is thus pretty
important.
On detecting that LPIs are still enabled, we taint the kernel (because
we're not sure of anything anymore), and try to disable LPIs. This can
fail, as implementations are allowed to implement GICR_CTLR.EnableLPI
as a one-way enable, meaning the redistributors cannot be reprogrammed
with new tables.
Should this happen, we fail probing the redistributor and warn the user
that things are pretty dire.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
[maz: reworded changelog, minor comment and message changes]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Microsemi Ocelot SoC has a pretty simple IRQ controller in its ICPU
block. Add a driver for it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We would like to reset the Group-0 Active Priority Registers
at boot time if they are available to us. They would be available
if SCR_EL3.FIQ was not set, but we cannot directly probe this bit,
and short of checking, we may end-up trapping to EL3, and the
firmware may not be please to get such an exception. Yes, this
is dumb.
Instead, let's use PMR to find out if its value gets affected by
SCR_EL3.FIQ being set. We use the fact that when SCR_EL3.FIQ is
set, the LSB of the priority is lost due to the shifting back and
forth of the actual priority. If we read back a 0, we know that
Group0 is unavailable. In case we read a non-zero value, we can
safely reset the AP0Rn register.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Clearing AP0Rn has created a number of regressions, due to systems
that have SCR_EL3.FIQ set. Even when addressing some obvious bugs,
GIC500 platforms seem to act bizarrely (we are supposed to have
5 bits of priority, but PMR seems to behave as if we had 6...).
Drop the AP0Rn reset for the time being, it is unlikely to have any
effect if kexec-ing.
Fixes: d6062a6d62 irqchip/gic-v3: Reset APgRn registers at boot time
Reported-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We cannot know the trigger of partitionned PPIs ahead of time
(when we instanciate the partitions), so let's not check them
early.
Reported-by: JeffyChen <jeffy.chen@rock-chips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is a huge number of broken device trees out there. Just
grepping through the tree for the use of IRQ_TYPE_NONE in conjunction
with the GIC is scary.
People just don't realise that IRQ_TYPE_NONE just doesn't exist, and
you just get whatever junk was there before. So let's make them aware
of the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is a huge number of broken device trees out there. Just
grepping through the tree for the use of IRQ_TYPE_NONE in conjunction
with the GIC is scary.
People just don't realise that IRQ_TYPE_NONE just doesn't exist, and
you just get whatever junk was there before. So let's make them aware
of the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds functionality to resend the MAPC command to an ITS node on
resume. If the ITS is powered down during suspend and the collections
are not backed by memory, the ITS will lose that state. This just sets
up the known state for the collections after the ITS is restored.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Some platforms power off GIC logic in suspend, so we need to
save/restore state. The distributor and redistributor registers need
to be handled in firmware code due to access permissions on those
registers, but the ITS registers can be restored in the kernel.
We limit this to systems where the ITS collections are implemented
in HW (as opposed to being backed by memory tables), as they are
the only ones that cannot be dealt with by the firmware.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
[maz: fixed changelog, dropped DT property, limited to HCC being >0]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
For most GICv3 implementations, enabling LPIs is a one way switch.
Once they're on, there is no turning back, which completely kills
kexec (pending tables will always be live, and we can't tell the
secondary kernel where they are).
This is really annoying if you plan to use Linux as a bootloader,
as it pretty much guarantees that the secondary kernel won't be
able to use MSIs, and may even see some memory corruption. Bad.
A workaround for this unfortunate situation is to allow the kernel
not to enable LPIs, even if the feature is present in the HW. This
would allow Linux-as-a-bootloader to leave LPIs alone, and let the
secondary kernel to do whatever it wants with them.
Let's introduce a boolean "irqchip.gicv3_nolpi" command line option
that serves that purpose.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Booting a crash kernel while in an interrupt handler is likely
to leave the Active Priority Registers with some state that
is not relevant to the new kernel, and is likely to lead
to erratic behaviours such as interrupts not firing as their
priority is already active.
As a sanity measure, wipe the APRs clean on startup. We make
sure to wipe both group 0 and 1 registers in order to avoid
any surprise.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Booting a crash kernel while in an interrupt handler is likely
to leave the Active Priority Registers with some state that
is not relevant to the new kernel, and is likely to lead
to erratic behaviours such as interrupts not firing as their
priority is already active.
As a sanity measure, wipe the APRs clean on startup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Power Domain Controller (PDC) on QTI SoCs like SDM845 houses an
interrupt controller along with other domain control functions to handle
interrupt related functions like handle falling edge or active low which
are not detected at the GIC and handle wakeup interrupts.
The interrupt controller is on an always-on domain for the purpose of
waking up the processor. Only a subset of the processor's interrupts are
routed through the PDC to the GIC. The PDC powers on the processors'
domain, when in low power mode and replays pending interrupts so the GIC
may wake up the processor.
Signed-off-by: Archana Sathyakumar <asathyak@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since commit 6f46aedb9c ("irqchip: renesas-irqc: Add wake-up
support"), when an IRQ is used for wakeup, the INTC
block's module clock is manually kept running during system suspend, to
make sure the device stays active.
However, this explicit clock handling is merely a workaround for a
failure to properly communicate wakeup information to the device core.
Instead, set the device's power.wakeup_path field, to indicate this
device is part of the wakeup path. Depending on the PM Domain's
active_wakeup configuration, the genpd core code will keep the device
enabled (and the clock running) during system suspend when needed.
This allows for the removal of all explicit clock handling code from the
driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since commit 705bc96c2c ("irqchip: renesas-intc-irqpin: Add
minimal runtime PM support"), when an IRQ is used for wakeup, the INTC
block's module clock (if exists) is manually kept running during system
suspend, to make sure the device stays active.
However, this explicit clock handling is merely a workaround for a
failure to properly communicate wakeup information to the device core.
Instead, set the device's power.wakeup_path field, to indicate this
device is part of the wakeup path. Depending on the PM Domain's
active_wakeup configuration, the genpd core code will keep the device
enabled (and the clock running) during system suspend when needed.
This allows for the removal of all explicit clock handling code from the
driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
imx_gpcv2_get_wakeup_source() is not used anywhere, so remove it.
This fixes the following sparse warning:
drivers/irqchip/irq-imx-gpcv2.c:34:5: warning: symbol 'imx_gpcv2_get_wakeup_source' was not declared. Should it be static?
Fixes: e324c4dc4a ("irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When struct its_device instances are created, the nr_ites member
will be set to a power of 2 that equals or exceeds the requested
number of MSIs passed to the msi_prepare() callback. At the same
time, the LPI map is allocated to be some multiple of 32 in size,
where the allocated size may be less than the requested size
depending on whether a contiguous range of sufficient size is
available in the global LPI bitmap.
This may result in the situation where the nr_ites < nr_lpis, and
since nr_ites is what we program into the hardware when we map the
device, the additional LPIs will be non-functional.
For bog standard hardware, this does not really matter. However,
in cases where ITS device IDs are shared between different PCIe
devices, we may end up allocating these additional LPIs without
taking into account that they don't actually work.
So let's make nr_ites at least 32. This ensures that all allocated
LPIs are 'live', and that its_alloc_device_irq() will fail when
attempts are made to allocate MSIs beyond what was allocated in
the first place.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[maz: updated comment]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We want the IIO/Staging fixes in here, and to resolve a merge problem
with the move of the fsl-mc code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that arch/metag/ has been removed, remove the two metag irqchip
drivers. They are of no value without the architecture code.
- irq-metag: Meta internal (HWSTATMETA) interrupt code.
- irq-metag-ext: Meta External interrupt code.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-metag@vger.kernel.org
Now that the fsl-mc bus core infrastructure is out of staging, the
remaining irqchip glue code used (irq-gic-v3-its-fsl-mc-msi.c) goes
to drivers/irqchip.
Create new Kconfig option for irqchip code that depends on
FSL_MC_BUS and ARM_GIC_V3_ITS. This ensures irqchip code only
gets built on ARM64 platforms. We can now remove #ifdef
GENERIC_MSI_DOMAIN_OPS as it was only needed for x86.
Signed-off-by: Stuart Yoder <stuyoder@gmail.com>
[rebased, add dpaa2_eth and dpio #include updates]
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[rebased, split irqchip to separate patch]
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
[add Kconfig dependency on ARM_GIC_V3_ITS]
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the Andestech Internal Vector Interrupt Controller
driver. You can find the spec here. Ch4.9 of AndeStar SPA V3 Manual.
http://www.andestech.com/product.php?cls=9
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Save 26 lines worth of Sparse complaints by fixing up this minor
mishap. The pointee lies in the __iomem space; the pointer does not.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful. so delete the prints.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We'd never implemented Multi-MSI support with GICv2m, because
it is weird and clunky, and you'd think people would rather use
MSI-X.
Turns out there is still plenty of devices out there that rely
on Multi-MSI. Oh well, let's teach that trick to the v2m widget,
it is not a big deal anyway.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A DMB instruction can be used to ensure the relative order of only
memory accesses before and after the barrier. Since writes to system
registers are not memory operations, barrier DMB is not sufficient
for observability of memory accesses that occur before ICC_SGI1R_EL1
writes.
A DSB instruction ensures that no instructions that appear in program
order after the DSB instruction, can execute until the DSB instruction
has completed.
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will.deacon@arm.com>,
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
[ 5.058454] irq 13, desc: ffffffff80a7ad80, depth: 1, count: 0, unhandled: 0
[ 5.062057] ->handle_irq(): ffffffff801b1838,
[ 5.062175] handle_bad_irq+0x0/0x2c0
Where IRQ 13 is the UART interrupt.
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org
Fixes: 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On some platforms msi parent address regions have to be excluded from
normal IOVA allocation in that they are detected and decoded in a HW
specific way by system components and so they cannot be considered normal
IOVA address space.
Add a helper function that retrieves ITS address regions - the msi
parent - through IORT device <-> ITS mappings and reserves it so that
these regions will not be translated by IOMMU and will be excluded from
IOVA allocations. The function checks for the smmu model number and
only applies the msi reservation if the platform requires it.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[For the ITS part]
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJad5lgAAoJEFmIoMA60/r8s2kQAI3PztawDpaCP9Z12pkbBHSt
Ho0xTyk9rCZi9kQJbNjc+a+QrlA3QmTHXIXerB3LSWoh7M+XhsECjem92eHpgLNS
JvYPhTfOrCr0vdiAmOz6hD0AqN/psrbfzgiJhSwomsGEFS77k7kERSJckRv81sxb
Aj5F/WjucAgLorwm4auveAJEQ7atE7/6pkXzoqYm4G6NLOb46jUcRGndrnvXZBlz
fws8fBM4BHyi7i25CYQl24tFq1CGax1rIPgLg+4KnH76bQk/N6Ju0sGVSzfh+hG8
SIerK9bJbzGRAuNKoxB3aO1dyzsK3x9WztE2mG98w5trOISPIR1FqnvC/225FWAU
d6eIXiC7wKnEx+DElNTzCjzfHc7SAJoupO32H7CoiTe5zPUlWlxJ1zLYkK1gt50q
m8PRBiYTglxyznzrO0drtcdjEzvbdZNRrsYnul4wi1vSHzjk6F6XLtzT10XWM1M1
1pXLB8384FTj0Hu4bq6Y3Aivkmz0Sf+eQM2NaOwe+Zj7/1VV0d3lvi4LUXkqzLCA
FoXPJSMxG2Qu+iflCeYRQBJjExaZH3eNLZ3dT6QpcJrjaFVedd9u5DeeFqNL27zV
bhr8TdqrR4p4rc8EBAGoCapw96IxLZROKB3gxbrZVOpfIZpzthwHbElHX6aqUgF4
w/EV1JWs36WXWaxFk8wd
=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
Pull irq fixes from Thomas Gleixner:
"Two small changes:
- a fix for a interrupt regression caused by the vector management
changes in 4.15 affecting museum pieces which rely on interrupt
probing for legacy (e.g. parallel port) devices.
One of the startup calls in the autoprobe code was not changed to
the new activate_and_startup() function resulting in a warning and
as a consequence failing to discover the device interrupt.
- a trivial update to the copyright/license header of the STM32 irq
chip driver"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Make legacy autoprobing work again
irqchip/stm32: Fix copyright
- Security mitigations:
- variant 2: invalidating the branch predictor with a call to secure firmware
- variant 3: implementing KPTI for arm64
- 52-bit physical address support for arm64 (ARMv8.2)
- arm64 support for RAS (firmware first only) and SDEI (software
delegated exception interface; allows firmware to inject a RAS error
into the OS)
- Perf support for the ARM DynamIQ Shared Unit PMU
- CPUID and HWCAP bits updated for new floating point multiplication
instructions in ARMv8.4
- Removing some virtual memory layout printks during boot
- Fix initial page table creation to cope with larger than 32M kernel
images when 16K pages are enabled
-----BEGIN PGP SIGNATURE-----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=iEjP
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"The main theme of this pull request is security covering variants 2
and 3 for arm64. I expect to send additional patches next week
covering an improved firmware interface (requires firmware changes)
for variant 2 and way for KPTI to be disabled on unaffected CPUs
(Cavium's ThunderX doesn't work properly with KPTI enabled because of
a hardware erratum).
Summary:
- Security mitigations:
- variant 2: invalidate the branch predictor with a call to
secure firmware
- variant 3: implement KPTI for arm64
- 52-bit physical address support for arm64 (ARMv8.2)
- arm64 support for RAS (firmware first only) and SDEI (software
delegated exception interface; allows firmware to inject a RAS
error into the OS)
- perf support for the ARM DynamIQ Shared Unit PMU
- CPUID and HWCAP bits updated for new floating point multiplication
instructions in ARMv8.4
- remove some virtual memory layout printks during boot
- fix initial page table creation to cope with larger than 32M kernel
images when 16K pages are enabled"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (104 commits)
arm64: Fix TTBR + PAN + 52-bit PA logic in cpu_do_switch_mm
arm64: Turn on KPTI only on CPUs that need it
arm64: Branch predictor hardening for Cavium ThunderX2
arm64: Run enable method for errata work arounds on late CPUs
arm64: Move BP hardening to check_and_switch_context
arm64: mm: ignore memory above supported physical address size
arm64: kpti: Fix the interaction between ASID switching and software PAN
KVM: arm64: Emulate RAS error registers and set HCR_EL2's TERR & TEA
KVM: arm64: Handle RAS SErrors from EL2 on guest exit
KVM: arm64: Handle RAS SErrors from EL1 on guest exit
KVM: arm64: Save ESR_EL2 on guest SError
KVM: arm64: Save/Restore guest DISR_EL1
KVM: arm64: Set an impdef ESR for Virtual-SError using VSESR_EL2.
KVM: arm/arm64: mask/unmask daif around VHE guests
arm64: kernel: Prepare for a DISR user
arm64: Unconditionally enable IESB on exception entry/return for firmware-first
arm64: kernel: Survive corrected RAS errors notified by SError
arm64: cpufeature: Detect CPU RAS Extentions
arm64: sysreg: Move to use definitions for all the SCTLR bits
arm64: cpufeature: __this_cpu_has_cap() shouldn't stop early
...
The ACPI specification says OS shouldn't attempt to use GICC configuration
parameters if the flag ACPI_MADT_ENABLED is cleared. The ARM64-SMP code
skips the disabled GICC entries but not causing any issue. However the
current GICv3 driver probe bails out causing kernel panic() instead of
skipping the disabled GICC interfaces. This issue happens on systems
where redistributor regions are not in the always-on power domain and
one of GICC interface marked with ACPI_MADT_ENABLED=0.
This patch does the two things to fix the panic.
- Don't return an error in gic_acpi_match_gicc() for disabled GICC entry.
- No need to keep GICR region information for disabled GICC entry.
Observed kernel crash on QDF2400 platform GICC entry is disabled.
Kernel crash traces:
Kernel panic - not syncing: No interrupt controller found.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.5 #26
[<ffff000008087770>] dump_backtrace+0x0/0x218
[<ffff0000080879dc>] show_stack+0x14/0x20
[<ffff00000883b078>] dump_stack+0x98/0xb8
[<ffff0000080c5c14>] panic+0x118/0x26c
[<ffff000008b62348>] init_IRQ+0x24/0x2c
[<ffff000008b609fc>] start_kernel+0x230/0x394
[<ffff000008b601e4>] __primary_switched+0x64/0x6c
---[ end Kernel panic - not syncing: No interrupt controller found.
Disabled GICC subtable example:
Subtable Type : 0B [Generic Interrupt Controller]
Length : 50
Reserved : 0000
CPU Interface Number : 0000003D
Processor UID : 0000003D
Flags (decoded below) : 00000000
Processor Enabled : 0
Performance Interrupt Trig Mode : 0
Virtual GIC Interrupt Trig Mode : 0
Parking Protocol Version : 00000000
Performance Interrupt : 00000017
Parked Address : 0000000000000000
Base Address : 0000000000000000
Virtual GIC Base Address : 0000000000000000
Hypervisor GIC Base Address : 0000000000000000
Virtual GIC Interrupt : 00000019
Redistributor Base Address : 0000FFFF88F40000
ARM MPIDR : 000000000000000D
Efficiency Class : 00
Reserved : 000000
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add device driver for a virtual programmable interrupt controller
The virtual PIC is designed as a device tree-based interrupt controller.
The compatible string used by OS for binding the driver is
"google,goldfish-pic".
Signed-off-by: Miodrag Dinic <miodrag.dinic@mips.com>
Signed-off-by: Goran Ferenc <goran.ferenc@mips.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In case of error, the function ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 9b54470afd ("irqchip: add initial support for ompic")
Acked-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to properly define the polarity of the per-cpu interrupts,
we need to support for a second property cell. But this must be
optional to keep backward compatibility with old DT blobs.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Use the new generic helper of_cpu_node_to_id() instead
of using our own version to map a device node to logical CPU
number.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.
No functional change.
Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Set I/O port resource structs to have IORESOURCE_IO in their type field.
Previously we marked these as merely IORESOURCE_BUSY without indicating the
type. Setting the type doesn't fix any functional problem but makes %pR
on the resource work better.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull irq fixes from Thomas Glexiner:
- unbreak the irq trigger type check for legacy platforms
- a handful fixes for ARM GIC v3/4 interrupt controllers
- a few trivial fixes all over the place
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/matrix: Make - vs ?: Precedence explicit
irqchip/imgpdc: Use resource_size function on resource object
irqchip/qcom: Fix u32 comparison with value less than zero
irqchip/exiu: Fix return value check in exiu_init()
irqchip/gic-v3-its: Remove artificial dependency on PCI
irqchip/gic-v4: Add forward definition of struct irq_domain_ops
irqchip/gic-v3: pr_err() strings should end with newlines
irqchip/s3c24xx: pr_err() strings should end with newlines
irqchip/gic-v3: Fix ppi-partitions lookup
irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
genirq: Track whether the trigger type has been set
The comparison of u32 nregs being less than zero is never true since
nregs is unsigned. Fix this by making nregs a signed integer.
Fixes: f20cc9b00c ("irqchip/qcom: Add IRQ combiner driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171117183553.2739-1-colin.king@canonical.com
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs, and
after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJaDayXAAoJEED/6hsPKofo/3UH/3HvlcHt+ADTkCU1/iiKAs+i
0zngIOXIxgHDnV0ww6bV+Znww0BzTYgKCAXX76z603jdpDwG/pzQQcbLDF5ZoJnD
sQtF10gZinWaRsHlfbLqjrHGL2pGDHO1UKBKLJ0bAIyORPZBxs7i+VmrY/blnr9c
0wsybJ8RbvwAxjsDL5jeX/z4NehPupmKUc4Lf0eZdSHwVOf9sjn+MP6jJ0r2JcIb
D+zddPBiLStzN97t4gZpQsrlj3LKrDS+6hY+1TjSvlh+yHKFVFh58VhLm4DuDeb5
bYOAlWJ/gAWEzfvr5Ld+Nd7SqWWn/14logPkQ4gcU4BI/neAOzk4c6hJfCHl1nk=
=593n
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"First batch of KVM changes for 4.15
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs,
and after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups"
* tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (89 commits)
KVM: s390: provide a capability for AIS state migration
KVM: s390: clear_io_irq() requests are not expected for adapter interrupts
KVM: s390: abstract conversion between isc and enum irq_types
KVM: s390: vsie: use common code functions for pinning
KVM: s390: SIE considerations for AP Queue virtualization
KVM: s390: document memory ordering for kvm_s390_vcpu_wakeup
KVM: PPC: Book3S HV: Cosmetic post-merge cleanups
KVM: arm/arm64: fix the incompatible matching for external abort
KVM: arm/arm64: Unify 32bit fault injection
KVM: arm/arm64: vgic-its: Implement KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: Document KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: vgic-its: Free caches when GITS_BASER Valid bit is cleared
KVM: arm/arm64: vgic-its: New helper functions to free the caches
KVM: arm/arm64: vgic-its: Remove kvm_its_unmap_device
arm/arm64: KVM: Load the timer state when enabling the timer
KVM: arm/arm64: Rework kvm_timer_should_fire
KVM: arm/arm64: Get rid of kvm_timer_flush_hwstate
KVM: arm/arm64: Avoid phys timer emulation in vcpu entry/exit
KVM: arm/arm64: Move phys_timer_emulate function
KVM: arm/arm64: Use kvm_arm_timer_set/get_reg for guest register traps
...
In case of error, the function of_iomap() returns NULL pointer not
ERR_PTR().
Replace the IS_ERR() test of the return value with NULL test and return
a proper error code.
Fixes: 706cffc1b9 ("irqchip/exiu: Add support for Socionext Synquacer EXIU controller")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/1510642648-123574-1-git-send-email-weiyongjun1@huawei.com
- A core irq fix for legacy cases where the irq trigger is not reported
by firmware
- A couple of GICv3/4 fixes (Kconfig, of-node refcount, error handling)
- Trivial pr_err fixes
-----BEGIN PGP SIGNATURE-----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=/8DQ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.15, take #4 from Marc Zyngier
- A core irq fix for legacy cases where the irq trigger is not reported
by firmware
- A couple of GICv3/4 fixes (Kconfig, of-node refcount, error handling)
- Trivial pr_err fixes
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
Small Things:
- Move OpenRISC docs into Documentation and clean them up
- Document previously undocumented devicetree bindings
- Update the or1ksim dts to use stdout-path
OpenRISC SMP support details:
- First the "use shadow registers" and "define CPU_BIG_ENDIAN as true"
get the architecture ready for SMP.
- The "add 1 and 2 byte cmpxchg support" and "use qspinlocks and
qrwlocks" add the SMP locking infrastructure as needed. Using the
qspinlocks and qrwlocks as suggested by Peter Z while reviewing the
original spinlocks implementation.
- The "support for ompic" adds a new irqchip device which is used for
IPI communication to support SMP.
- The "initial SMP support" adds smp.c and makes changes to all of the
necessary data-structures to be per-cpu.
- The remaining patches are bug fixes and debug helpers which I wanted
to keep separate from the "initial SMP support" in order to allow them
to be reviewed on their own. This includes:
- add cacheflush support to fix icache aliasing
- fix initial preempt state for secondary cpu tasks
- sleep instead of spin on secondary wait
- support framepointers and STACKTRACE_SUPPORT
- enable LOCKDEP_SUPPORT and irqflags tracing
- timer sync: Add tick timer sync logic
- fix possible deadlock in timer sync, pointed out by mips guys
Note: the irqchip patch was reviewed with Marc and we agreed to push it
together with these patches.
-----BEGIN PGP SIGNATURE-----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=euP7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
"The OpenRISC work is a bit more interesting this time, adding SMP
support and a few general cleanups.
Small Things:
- Move OpenRISC docs into Documentation and clean them up
- Document previously undocumented devicetree bindings
- Update the or1ksim dts to use stdout-path
OpenRISC SMP support details:
- First the "use shadow registers" and "define CPU_BIG_ENDIAN as
true" get the architecture ready for SMP.
- The "add 1 and 2 byte cmpxchg support" and "use qspinlocks and
qrwlocks" add the SMP locking infrastructure as needed. Using the
qspinlocks and qrwlocks as suggested by Peter Z while reviewing the
original spinlocks implementation.
- The "support for ompic" adds a new irqchip device which is used for
IPI communication to support SMP.
- The "initial SMP support" adds smp.c and makes changes to all of
the necessary data-structures to be per-cpu.
The remaining patches are bug fixes and debug helpers which I wanted
to keep separate from the "initial SMP support" in order to allow them
to be reviewed on their own. This includes:
- add cacheflush support to fix icache aliasing
- fix initial preempt state for secondary cpu tasks
- sleep instead of spin on secondary wait
- support framepointers and STACKTRACE_SUPPORT
- enable LOCKDEP_SUPPORT and irqflags tracing
- timer sync: Add tick timer sync logic
- fix possible deadlock in timer sync, pointed out by mips guys
Note: the irqchip patch was reviewed with Marc and we agreed to push
it together with these patches"
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: fix possible deadlock scenario during timer sync
openrisc: pass endianness info to sparse
openrisc: add tick timer multi-core sync logic
openrisc: enable LOCKDEP_SUPPORT and irqflags tracing
openrisc: support framepointers and STACKTRACE_SUPPORT
openrisc: add simple_smp dts and defconfig for simulators
openrisc: add cacheflush support to fix icache aliasing
openrisc: sleep instead of spin on secondary wait
openrisc: fix initial preempt state for secondary cpu tasks
openrisc: initial SMP support
irqchip: add initial support for ompic
dt-bindings: add openrisc to vendor prefixes list
openrisc: use qspinlocks and qrwlocks
openrisc: add 1 and 2 byte cmpxchg support
openrisc: use shadow registers to save regs on exception
dt-bindings: openrisc: Add OpenRISC platform SoC
Documentation: openrisc: Updates to README
Documentation: Move OpenRISC docs out of arch/
MAINTAINERS: Add OpenRISC pic maintainer
openrisc: dts: or1ksim: Add stdout-path
The GICv3 ITS doesn't really depend on PCI. Only the PCI/MSI
part of it does, and there is no reason not to blow away most
of the irqchip stack because PCI is not selected (though not
selecting PCI seem to be asking for punishment, but hey...).
So let's split the PCI-specific part from the ITS in the Kconfig
file, and let's make that part depend on PCI. Architecture specific
hacks (arch/arm{,64}/Kconfig) will be addressed in a separate patch.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Fix child-node lookup during initialisation, which ended up searching
the whole device tree depth-first starting at the parent rather than
just matching on its children.
To make things worse, the parent gic node was prematurely freed, while
the ppi-partitions node was leaked.
Fixes: e3825ba1af ("irqchip/gic-v3: Add support for partitioned PPIs")
Cc: stable <stable@vger.kernel.org> # 4.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Should the call to irq_set_vcpu_affinity() fail at map time,
we should restore the normal lazy-disable behaviour instead
of staying with the eager disable that GICv4 requires.
Reported-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- New Socionext Synquacer EXIU driver
- stm32 new platform support and fixes
- One GICv4 bugfix
- A couple of MIPS GIC cleanups
-----BEGIN PGP SIGNATURE-----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=Rym/
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for 4.15, take #3 from Marc Zyngier:
- New Socionext Synquacer EXIU driver
- stm32 new platform support and fixes
- One GICv4 bugfix
- A couple of MIPS GIC cleanups
If the physical address of the GIC resource cannot be read from device
tree, then the code falls back to reading it from the gcr_gic_base
register. Hopefully this has been set to a sane value by the bootloader
or some platform code, but is defined by the hardware manual to have
"undefined" reset state. Using it as the address at which the GIC will
be mapped into physical memory space can therefore be risky if it has
not been initialised, since it may result in the GIC being mapped to an
effectively random address anywhere in physical memory, where it might
conflict with peripherals or RAM and lead to weird crashes.
Since a "sane value" is very platform specific because it is particular
to the platform's memory map, it is difficult to test for. At the very
least, a warning message should be printed in the case that we trust the
inherited value.
Reported-by: Amit Kama <amit.kama@satixfy.com>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Several messages from the MIPS GIC driver include the text "GIC", but
the format is not standard. Add a pr_fmt of "irq-mips-gic: " and reword
the messages now that they will be prefixed with the driver name.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move irq_set_wake on interrupt mask, needed to wake up from
low power mode as the event mask is not able to do so.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-After cold boot, imr default value depends on hardware configuration.
-After hot reboot the registers must be cleared to avoid residue.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
stm32h7 has up to 96 inputs
(3 banks of 32 inputs max).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-Prepare to manage multi-bank of external interrupts
(N banks of 32 inputs).
-Prepare to manage registers offsets by compatible
(registers offsets could be different follow per stm32 platform).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Socionext Synquacer SoC has an external interrupt unit (EXIU)
that forwards a block of 32 configurable input lines to 32 adjacent
level-high type GICv3 SPIs.
The EXIU has per-interrupt level/edge and polarity controls, and
mask bits that keep the outgoing lines de-asserted, even though
the controller may still latch interrupt conditions that occur
while the line is masked.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
its_vpe_irq_domain_activate should always return 0. Really. There
is not a single case why it wouldn't. So this "return true;" is
really a copy/paste issue that got revealed now that we actually
check the return value of the activate method.
Brown paper bag day.
Fixes: 2247e1bf70 ("irqchip/gic-v3-its: Limit scope of VPE mapping to be per ITS")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Some systems without proper firmware and/or hardware description data
don't support the split EOI and deactivate operation.
On such systems, we cannot leave the physical interrupt active after the
timer handler on the host has run, so we cannot support KVM with an
in-kernel GIC with the timer changes we are about to introduce.
This patch makes sure that trying to initialize the KVM GIC code will
fail on such systems.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
IPI driver for the Open Multi-Processor Interrupt Controller (ompic) as
described in the Multi-core support section of the OpenRISC 1.2
architecture specification:
https://github.com/openrisc/doc/raw/master/openrisc-arch-1.2-rev0.pdf
Each OpenRISC core contains a full interrupt controller which is used in
the SMP architecture for interrupt balancing. This IPI device, the
ompic, is the only external device required for enabling SMP on
OpenRISC.
Pending ops are stored in a memory bit mask which can allow multiple
pending operations to be set and serviced at a time. This is mostly
borrowed from the alpha IPI implementation.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: converted ops to bitmask, wrote commit message]
Signed-off-by: Stafford Horne <shorne@gmail.com>
- A number of MIPS GIC updates and cleanups
- One GICv4 update
- Another firmware workaround for GICv2
- Support for Mason8 GPIOs
- Tiny documentation fix
-----BEGIN PGP SIGNATURE-----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=Aozt
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull the second batch of irqchip updates for 4.15 from marc Zyngier:
- A number of MIPS GIC updates and cleanups
- One GICv4 update
- Another firmware workaround for GICv2
- Support for Mason8 GPIOs
- Tiny documentation fix
We have 2 bitmaps used to keep track of interrupts dedicated to IPIs in
the MIPS GIC irqchip driver. These bitmaps are only used from the one
compilation unit of that driver, and so can be made static. Do so in
order to avoid polluting the symbol table & global namespace.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The gic_set_type() function included writes to the MIPS GIC polarity,
trigger & dual-trigger registers in each case of a switch statement
determining the IRQs type. This is all well & good when we only have a
single cluster & thus a single GIC whose register we want to update. It
will lead to significant duplication once we have multi-cluster support
& multiple GICs to update.
Refactor this such that we determine values for the polarity, trigger &
dual-trigger registers and then have a single set of register writes
following the switch statement. This will allow us to write the same
values to each GIC in a multi-cluster system in a later patch, rather
than needing to duplicate more register writes in each case.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Following the past few patches nothing uses the gic_vpes variable any
longer. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reserving a number of IPIs based upon the number of VPs reported by the
GIC makes little sense for a few reasons:
- The kernel may have been configured with NR_CPUS less than the number
of VPs in the cluster, in which case using gic_vpes causes us to
reserve more interrupts for IPIs than we will possibly use.
- If a kernel is configured without support for multi-threading & runs
on a system with multi-threading & multiple VPs per core then we'll
similarly reserve more interrupts for IPIs than we will possibly use.
- In systems with multiple clusters the GIC can only provide us with
the number of VPs in its cluster, not across all clusters. In this
case we'll reserve fewer interrupts for IPIs than we need.
Fix these issues by using num_possible_cpus() instead, which in all
cases is actually indicative of how many IPIs we may need.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rather than configuring EIC mode for all CPUs during boot, configure it
locally on each when they come online. This will become important with
multi-cluster support, since clusters may be powered on & off (for
example via hotplug) and would lose the EIC configuration when powered
off.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently walk through the range 0..gic_vpes-1, expecting these
values all to be valid Linux CPU numbers to provide to mips_cm_vp_id(),
and masking all routable local interrupts during boot. This approach has
a few drawbacks:
- In multi-cluster systems we won't have access to all CPU's GIC local
registers when the driver is probed, since clusters (and their GICs)
may be powered down at this point & only brought online later.
- In multi-cluster systems we may power down clusters at runtime, for
example if we offline all CPUs within it via hotplug, and the
cluster's GIC may lose state. We therefore need to reinitialise it
when powering back up, which this approach does not take into
account.
- The range 0..gic_vpes-1 may not all be valid Linux CPU numbers, for
example if we run a kernel configured to support fewer CPUs than the
system it is running on actually has. In this case we'll get garbage
values from mips_cm_vp_id() as we read past the end of the cpu_data
array.
Fix this and simplify the code somewhat by writing an all-bits-set
value to the VP-local reset mask register when a CPU is brought online,
before any local interrupts are configured for it. This removes the need
for us to access all CPUs during driver probe, removing all of the
problems described above.
In the name of simplicity we drop the checks for routability of
interrupts and simply clear the mask bits for all interrupts. Bits for
non-routable local interrupts will have no effect so there's no point
performing extra work to avoid modifying them.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The gic_all_vpes_local_irq_controller chip currently attempts to operate
on all CPUs/VPs in the system when masking or unmasking an interrupt.
This has a few drawbacks:
- In multi-cluster systems we may not always have access to all CPUs in
the system. When all CPUs in a cluster are powered down that
cluster's GIC may also power down, in which case we cannot configure
its state.
- Relatedly, if we power down a cluster after having configured
interrupts for CPUs within it then the cluster's GIC may lose state &
we need to reconfigure it. The current approach doesn't take this
into account.
- It's wasteful if we run Linux on fewer VPs than are present in the
system. For example if we run a uniprocessor kernel on CPU0 of a
system with 16 CPUs then there's no point in us configuring CPUs
1-15.
- The implementation is also lacking in that it expects the range
0..gic_vpes-1 to represent valid Linux CPU numbers which may not
always be the case - for example if we run on a system with more VPs
than the kernel is configured to support.
Fix all of these issues by only configuring the affected interrupts for
CPUs which are online at the time, and recording the configuration in a
new struct gic_all_vpes_chip_data for later use by CPUs being brought
online. We register a CPU hotplug state (reusing
CPUHP_AP_IRQ_GIC_STARTING which the ARM GIC driver uses, and which seems
suitably generic for reuse with the MIPS GIC) and execute
irq_cpu_online() in order to configure the interrupts on the newly
onlined CPU.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The gic_local_irq_domain_map() function has only one callsite in
gic_irq_domain_map(), and the split between the two functions makes it
unclear that they duplicate calculations & checks.
Inline gic_local_irq_domain_map() into gic_irq_domain_map() in order to
clean this up. Doing this makes the following small issues obvious, and
the patch tidies them up:
- Both functions used GIC_HWIRQ_TO_LOCAL() to convert a hwirq number to
a local IRQ number. We now only do this once. Although the compiler
ought to have optimised this away before anyway, the change leaves us
with less duplicate code.
- gic_local_irq_domain_map() had a check for invalid local interrupt
numbers (intr > GIC_LOCAL_INT_FDC). This condition can never occur
because any hwirq higher than those used for local interrupts is a
shared interrupt, which gic_irq_domain_map() already handles
separately. We therefore remove this check.
- The decision of whether to map the interrupt to gic_cpu_pin or
timer_cpu_pin can be handled within the existing switch statement in
gic_irq_domain_map(), shortening the code a little.
The change additionally prepares us nicely for the following patch of
the series which would otherwise need to duplicate the check for whether
a local interrupt should be percpu_devid or just percpu (ie. the switch
statement from gic_irq_domain_map()) in gic_local_irq_domain_map().
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Meson8 uses the same GPIO interrupt controller IP block as the other
Meson SoCs. A total of 134 pins can be spied on, which is the sum of:
- 22 pins on bank GPIOX
- 17 pins on bank GPIOY
- 30 pins on bank GPIODV
- 10 pins on bank GPIOH
- 15 pins on bank GPIOZ
- 7 pins on bank CARD
- 19 pins on bank BOOT
- 14 pins in the AO domain
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is a lot of broken firmware out there that don't really
expose the information the kernel requires when it comes with dealing
with GICv2:
(1) Firmware that only describes the first 4kB of GICv2
(2) Firmware that describe 128kB of CPU interface, while
the usable portion of the address space is between
60 and 68kB
So far, we only deal with (2). But we have platforms exhibiting
behaviour (1), resulting in two sub-cases:
(a) The GIC is occupying 8kB, as required by the GICv2 architecture
(b) It is actually spread 128kB, and this is likely to be a version
of (2)
This patch tries to work around both (a) and (b) by poking at
the outside of the described memory region, and try to work out
what is actually there. This is of course unsafe, and should
only be enabled if there is no way to otherwise fix the DT provided
by the firmware (we provide a "irqchip.gicv2_force_probe" option
to that effect).
Note that for the time being, we restrict ourselves to GICv2
implementations provided by ARM, since there I have no knowledge
of an alternative implementations. This could be relaxed if such
an implementation comes to light on a broken platform.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we require the hypervisor to update the VLPI properties
once the the VLPI mapping has been established. While this
makes it easy for the ITS driver, it creates a window where
an incoming interrupt can be delivered with an unknown set
of properties. Not very nice.
Instead, let's add a "properties" field to the mapping structure,
and use that to configure the VLPI before it actually gets mapped.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver fails to compile with CONFIG_COMPILE_TEST=y on x86:
irq-meson-gpio.c: In function ‘meson_gpio_irq_parse_dt’:
irq-meson-gpio.c:343:8: error: implicit declaration of function
‘of_property_read_variable_u32_array’
ret = of_property_read_variable_u32_array(node,
Adding COMPILE_TEST to a driver requires at least compile testing it for
x86....
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
please pull the following:
- Danilo removes the clock provider driver stubs which are no longer needed
now that we have a proper CPRMAN clock provider driver
- Stefan moves the SMP startup code for BCM2836 from the interrupt controller
driver down to where it belongs in the architecture code, this was requested
by Marc Zyngier before comitting any fixes to that code
- Phil provides a fix for a future Raspberry Pi firmware which will make the
secondary cores wait for an event and therefore requires the CPU onlining
other cores to send such event (along with the appropriate barrier)
- Florian fixes the BRCMSTB UART debug stub to work correctly when using an
ARM BE8 kernel since there were some missing register read swapping needed
-----BEGIN PGP SIGNATURE-----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=h/36
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.15/soc' of http://github.com/Broadcom/stblinux into next/soc
Pull "Broadcom soc changes for 4.15 (part 1)" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC/Kconfig changes for 4.15
please pull the following:
- Danilo removes the clock provider driver stubs which are no longer needed
now that we have a proper CPRMAN clock provider driver
- Stefan moves the SMP startup code for BCM2836 from the interrupt controller
driver down to where it belongs in the architecture code, this was requested
by Marc Zyngier before comitting any fixes to that code
- Phil provides a fix for a future Raspberry Pi firmware which will make the
secondary cores wait for an event and therefore requires the CPU onlining
other cores to send such event (along with the appropriate barrier)
- Florian fixes the BRCMSTB UART debug stub to work correctly when using an
ARM BE8 kernel since there were some missing register read swapping needed
* tag 'arm-soc/for-4.15/soc' of http://github.com/Broadcom/stblinux:
ARM: brcmstb: Add appropriate ARM_BE8() macros for swapping
ARM: bcm2836: Send event when onlining other cores
irqchip: bcm2836: Move SMP startup code to arch/arm (v2)
clk: bcm2835: remove remains from stub clk driver
In case of error, the function of_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test..
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for the interrupt gpio controller found on Amlogic's meson
SoC family.
This controller is a separate controller from the gpio controller. It is
able to spy on the SoC pad. It is essentially a 256 to 8 router with a
filtering block to select level or edge and polarity. The number of actual
mappable inputs depends on the SoC.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When setting the affinity of a VPE (either because we map or move
it), make sure the effective affinity is correctly reported back
to the core kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Sending VINVALL to all ITSs is completely pointless, as all
we're trying to achieve is to tell the redistributor that
the property table for this VPE should be invalidated.
Let's issue the command on the first valid ITS and be done with it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we map all VPEs on all ITSs. While this is not wrong,
this is quite a big hammer, as moving a VPE around requires
all ITSs to be synchronized. Needles to say, this is an
expensive proposition.
Instead, let's switch to a mode where we issue VMAPP commands
only on ITSs that are actually involved in reporting interrupts
to the given VM.
For that purpose, we refcount the number of interrupts are are
mapped for this VM on each ITS, performing the map/unmap
operations as required. It then allows us to use this refcount
to only issue VMOVP to the ITSs that need to know about this
VM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, its_send_vmapp operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, its_send_vinvall operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're about to make use of the maximum number of ITSs in
a GICv4 system, let's make this value global (and rename it to
GICv4_ITS_LIST_MAX).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At boot time, we enumerate all the GICv4-capable ITSs, and build
a mask of the available ITSs. Take this opportunity to store
the ITS number in the its_node structure so that we can use it
at a later time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ITSes on the Hip07 (as present in the Huawei D05) are broken when
it comes to addressing the redistributors, and need to be explicitely
told to address the VLPI page instead of the redistributor base address.
So let's add yet another quirk, fixing up the target address
in the command stream.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to be able to issue command variants depending on
how broken an ITS is, let's pass the its pointer to all
command building primitives.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the ITS stops processing commands, we're pretty much toasted
as we cannot update the configuration anymore (and we're not
even sure that the ITS still translates interrups).
If that happens, let's dump some basic information about the
state of affairs before moving on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Socionext Synquacer SoC's implementation of GICv3 has a so-called
'pre-ITS', which maps 32-bit writes targeted at a separate window of
size '4 << device_id_bits' onto writes to GITS_TRANSLATER with device
ID taken from bits [device_id_bits + 1:2] of the window offset.
Writes that target GITS_TRANSLATER directly are reported as originating
from device ID #0.
So add a workaround for this. Given that this breaks isolation, clear
the IRQ_DOMAIN_FLAG_MSI_REMAP flag as well.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As it turns out, the IIDR is not sufficient to distinguish between GICv3
implementations when it comes to enabling quirks. So update the prototype
of the init() hook to return a bool, and interpret a 'false' return value
as no match, in which case the 'enabling workaround' log message should
not be printed.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Before adding another SoC whose device ID space deviates from the
value presented in the GIC ID registers, let's slightly refactor
the code so that the ID registers are probed before that quirks
handling executes. This allows us to move the device ID override
into the quirk handler itself.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A new feature Range Selector (RS) has been added to GIC specification
in order to support more than 16 CPUs at affinity level 0. New fields
are introduced in SGI system registers (ICC_SGI0R_EL1, ICC_SGI1R_EL1
and ICC_ASGI1R_EL1) to relax an artificial limit of 16 at level 0.
- A new RSS field in ICC_CTLR_EL3, ICC_CTLR_EL1 and ICV_CTLR_EL1:
[18] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
- A new RS field in ICC_SGI0R_EL1, ICC_SGI1R_EL1 and ICC_ASGI1R_EL1:
[47:44] - RangeSelector (RS) which group of 16 TargetList[n] field
TargetList[n] represents aff0 value ((RS*16)+n)
When ICC_CTLR_EL3.RSS==0 or ICC_CTLR_EL1.RSS==0, RS is RES0.
- A new RSS field in GICD_TYPER:
[26] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the initialization of the generic irq chip for the BCM7271 L2
interrupt controller. This controller only supports level
interrupts and uses the "brcm,bcm7271-l2-intc" compatibility
string.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Added register block offsets to the brcmstb_l2_intc_data structure
for the status and mask registers to support reading the active
interupts in an abstracted way. It seems like an irq_chip method
should have been provided for this, but it's not there yet.
Abstracted the implementation of the handler, suspend, and resume
functions to not use any hard coded register offsets.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Saving the generic chip pointer in the brcmstb_l2_intc_data prevents
the need to call irq_get_domain_generic_chip(). Also don't need to
save parent_irq and base there since local variables in the
brcmstb_l2_intc_of_init() function are just as good.
The handle_edge_irq flow or chained_irq_enter takes care of the
acknowledgment of the interrupt so it is redundant to clear it in
brcmstb_l2_intc_irq_handle().
irq_linear_revmap() is a fast path equivalent of irq_find_mapping()
that is appropriate to use for domain controllers of this type.
Defining irq_mask_ack is slightly more efficient than just
implementing irq_mask and irq_ack separately.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Use the of_device_get_match_data() helper instead of open coding.
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a menu for IRQ chip drivers. This makes the Device drivers menu be more
consistent (listing "subsystems" instead of specific options) and makes the
IRQCHIP options be listed in expected places for 'make menu|xconfig'.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/3db7385a-c6a1-5c93-0797-6f4b6b2b2cde@infradead.org
omap_nr_pending and omap_nr_irqs variables are initialized
right at the beginning of intc_of_init function, so there's
no need to statically initialize them.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171016161303.veumgcd3xom5c54r@lenoch
All mach-omap2 variants are device tree only now, so this function is dead
code. Remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-omap@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171016160422.uu2i7vvrgy7cc4aw@lenoch
The only usage of the irq_gc_mask_disable_reg_and_ack() function
is by the Tango irqchip driver. This usage is replaced by the
irq_gc_mask_disable_and_ack_set() function since it provides the
intended functionality.
Fixes: 4bba66899a ("irqchip/tango: Add support for Sigma Designs SMP86xx/SMP87xx interrupt controller")
Acked-by: Mans Rullgard <mans@mansr.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The current ITS driver works fine as long as normal memory and GICR
regions are located within the lower 48bit (>=0 && <2^48) physical
address space. Some of the registers GICR_PEND/PROP, GICR_VPEND/VPROP
and GITS_CBASER are handled properly but not all when configuring
the hardware with 52bit physical address.
This patch does the following changes to support 52bit PA.
-Handle 52bit PA in GITS_BASERn.
-Fix ITT_addr width to 52bits, bits[51:8].
-Fix RDbase width to 52bits, bits[51:16].
-Fix VPT_addr width to 52bits, bits[51:16].
Definition of the GITS_BASERn register when ITS PageSize is 64KB:
-Bits[47:16] of the register provide bits[47:16] of the table PA.
-Bits[15:12] of the register provide bits[51:48] of the table PA.
-Bits[15:00] of the base physical address are 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The VCPU table consists of vPE entries, and its size provides the number
of VPEs supported by GICv4 hardware. Unfortunately the maximum size of
the VPE table is not discoverable like Device table. All VLPI commands
limits the number of bits to 16 to hold VPEID, which is index into VCPU
table. Don't apply DEVID bits for VCPU table instead assume maximum bits
to 16.
ITS log messages on QDF2400 without fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
Virtual CPUs Table too large, reduce ids 32->26
Virtual CPUs too large, reduce ITS pages 8192->256
allocated 2097152 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
ITS log messages on QDF2400 with fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
allocated 65536 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The driver probe path hits 'BUG_ON(entries != vpe_proxy.dev->nr_ites)'
on systems where it has VLPI capability, doesn't support direct LPI
feature and boot with a single CPU.
Relax the BUG_ON() condition to fix the issue.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ls1012a implements only 1 MSI controller, and it is the same as
ls1043a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Commit 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") adjusted the way we handle masking interrupts to set &
clear the interrupt's bit in each pcpu_mask. This allows us to avoid
needing to read the GIC mask registers and perform a bitwise and of
their values with the pending & pcpu_masks.
Unfortunately this didn't quite work for IPIs, which were mapped to a
particular CPU/VP during initialisation but never set the affinity or
effective_affinity fields of their struct irq_desc. This led to them
losing their affinity when gic_unmask_irq() was called for them, and
they'd all become affine to cpu0.
Fix this by:
1) Setting the effective affinity of interrupts in
gic_shared_irq_domain_map(), which is where we actually map an
interrupt to a CPU/VP. This ensures that the effective affinity mask
is always valid, not just after explicitly setting affinity.
2) Using an interrupt's effective affinity when unmasking it, which
prevents gic_unmask_irq() from unintentionally changing which
pcpu_mask includes an interrupt.
Fixes: 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20170922062440.23701-3-paul.burton@imgtec.com
The MIPS GIC driver is incorrectly using __fls to shift registers,
intending to shift to the least significant bit of a value based upon
its mask but instead shifting off all but the value's top bit. It should
actually be using __ffs to shift to the first, not last, bit of the
value.
Apparently the system I used when testing commit 3680746abd
("irqchip: mips-gic: Convert remaining shared reg access to new
accessors") and commit b2b2e584ce ("irqchip: mips-gic: Clean up mti,
reserved-cpu-vectors handling") managed to work correctly despite this
issue, but not all systems do...
Fixes: 3680746abd ("irqchip: mips-gic: Convert remaining shared reg access to new accessors")
Fixes: b2b2e584ce ("irqchip: mips-gic: Clean up mti, reserved-cpu-vectors handling")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20170922062440.23701-2-paul.burton@imgtec.com
In order to easily provide SMP for BCM2837 on 32-bit and 64-bit
the SMP startup code was placed in irq-bcm2836. That's not the
right approach. So move this code where it belongs.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 41f4988cc2 ("irqchip/bcm2836: Add SMP support for the 2836")
Tested-by: Eric Anholt <eric@anholt.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
The write_gic_smask() & write_gic_rmask() functions take a shared
interrupt number as a parameter, but we're incorrectly providing them a
bitmask with the shared interrupt's bit set. This effectively means that
we mask or unmask the shared interrupt 1<<n rather than shared interrupt
n, and as a result likely drop interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 68898c8765f4 ("irqchip: mips-gic: Drop gic_(re)set_mask() functions")
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gcc-4.5 and earlier don't like named initializers for anonymous
union members:
drivers/irqchip/irq-gic-v4.c: In function 'its_map_vlpi':
drivers/irqchip/irq-gic-v4.c:176:3: error: unknown field 'map' specified in initializer
drivers/irqchip/irq-gic-v4.c:176:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:176:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c: In function 'its_get_vlpi':
drivers/irqchip/irq-gic-v4.c:192:3: error: unknown field 'map' specified in initializer
drivers/irqchip/irq-gic-v4.c:192:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:192:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c: In function 'its_prop_update_vlpi':
drivers/irqchip/irq-gic-v4.c:208:3: error: unknown field 'config' specified in initializer
drivers/irqchip/irq-gic-v4.c:208:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:208:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c:208:3: error: initialization makes pointer from integer without a cast
This is fairly easy to work around, by using extra curly braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
get_cpu_number() doesn't use existing helper to iterate over possible
CPUs, It will cause an error in case of discontinuous @cpu_possible_mask
such as 0b11110001, which can result from a core having failed to come
up on a SMP machine.
Fixed by using existing helper for_each_possible_cpu().
Signed-off-by: zijun_hu <zijun_hu@htc.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
gic_set_affinity() manually copies the provided cpumask to the struct
irq_common_data affinity field, returning IRQ_SET_MASK_OK_NOCOPY in
order to prevent the core code from doing that.
We can instead simply let the core code do it for us, by returning
IRQ_SET_MASK_OK instead of IRQ_SET_MASK_OK_NOCOPY & doing the copy
ourselves.
[ralf@linux-mips.org: Resolve merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17056/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently in gic_set_affinity() we calculate a temporary cpumask holding
the intersection of the provided cpumask & the CPUs that are online,
then we call cpumask_first twice on it to find the first such CPU. Since
we don't need the temporary cpumask for anything else & we only care
about the first CPU that's both online & in the provided cpumask, we can
instead use cpumask_first_and to find that CPU & drop the temporary
mask.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When parsing mti,reserved-cpu-vectors we generate a mask of all bits
that have been declared reserved, the loop through starting from bit 2
to find one that isn't reserved (ie. is zero).
This patch accomplishes the same task more simply by:
- Inititialising the reserved mask to 0x3 (ie. the 2 software
interrupts). This means we don't need to skip them later as the loop
previously has.
- Replacing the loop checking for zero bits with find_first_zero_bit,
which fits our needs now that the 2 software interrupts are marked
reserved. This requires that the type of reserved is changed to
unsigned long so that it's suitable for use with bitmap functions.
- Replacing the magic number 8 with the hamming weight of the ST0_IM
field - ie. the number of bits that a MIPS CPU has for interrupt
inputs. This is still a compile-time constant 8, but makes it
clearer why it's 8.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17054/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch avoids the need to read the GIC_SH_MASK* registers when
decoding shared interrupts by setting & clearing the interrupt's bit in
the appropriate CPU's pcpu_masks entry when masking or unmasking the
interrupt.
This effectively means that whilst an interrupt is masked we clear its
bit in all pcpu_masks, which causes gic_handle_shared_int() to ignore it
on all CPUs without needing to check GIC_SH_MASK*.
In essence, we add a little overhead to masking or unmasking interrupts
but in return reduce the overhead of the far more common task of
decoding interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17109/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
