Use the net namespace of the underlying rdma device.
After honoring the rdma device's namespace, the ipoib
netdev now also runs in the same net namespace of the
rdma device.
Add an API to read the net namespace of the rdma device
so that ULP such as IPoIB can use it to initialize its
netdev.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
After the last patch removing vlan_rwsem, it is an incremental step to
allow ipoib to work with netdevs that require the instance lock.
In several places, netdev_lock() is changed to netdev_lock_ops_to_full()
which takes care of not acquiring the lock again when the netdev is
already locked.
In ipoib_ib_tx_timeout_work() and __ipoib_ib_dev_flush() for HEAVY
flushes, the netdev lock is acquired/released. This is needed because
these functions end up calling .ndo_stop()/.ndo_open() on subinterfaces,
and the device may expect the netdev instance lock to be held.
ipoib_set_mode() now explicitly acquires ops lock while manipulating the
features, mtu and tx queues.
Finally, ipoib_napi_enable()/ipoib_napi_disable() now use the *_locked
variants of the napi_enable()/napi_disable() calls and optionally
acquire the netdev lock themselves depending on the dev they operate on.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1747829342-1018757-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
vlan_rwsem was added more than a decade ago to work around a deadlock
involving the original mutex being acquired twice, once from the wq.
Subsequent changes then tweaked it to partially protect access to
ipoib_dev_priv->child_intfs together with the RTNL. Flushing the wq
synchronously was also since then refactored to happen separately.
This semaphore unfortunately prevents updating ipoib to work with
devices that require the netdev lock, because of lock ordering issues
between RTNL, vlan_rwsem and the netdev instance locks of parent and
child devices.
To uncomplicate things, this commit replaces vlan_rwsem with the netdev
instance lock of the parent device. Both parent child_intfs list and the
children's list membership in it require holding the parent netdev
instance lock.
All call paths were carefully reviewed and no-longer-needed ASSERT_RTNL
calls were dropped. Some non-trivial changes:
- ipoib_match_gid_pkey_addr() now only acquires the instance lock and
iterates through child_intfs for the first level of recursion (the
parent), as it's not possible to have multiple levels of nested
subinterfaces.
- ipoib_open() and ipoib_stop() schedule tasks on the global workqueue
to open/stop child interfaces to avoid potentially acquiring nested
netdev instance locks. To avoid the device going away between the task
scheduling and execution, netdev_hold/netdev_put are used.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1747829342-1018757-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, flushing a netdevice involved first flushing all child
devices from the flush task itself. That requires holding the lock that
protects the list for the entire duration of the flush.
This poses a problem when converting from vlan_rwsem to the netdev
instance lock (next patch), because holding the parent lock while
trying to acquire a child lock makes lockdep unhappy, rightfully.
Fix this by splitting a big flush task into individual flush tasks
(all are already created in their respective ipoib_dev_priv structs)
and defining a helper function to enqueue all of them while holding the
list lock.
In ipoib_set_mac, the function is not used and the task is enqueued
directly, because in the subsequent patches locking is changed and this
function may be called with the netdev instance lock held.
This is effectively a noop, the wq is single-threaded and ordered and
will execute the same flush operations in the same order as before.
Furthermore, there should be no new races because
ipoib_parent_unregister_pre() calls flush_workqueue() after stopping new
work generation to wait for pending work to complete. flush_workqueue()
waits for all currently enqueued work to finish before returning.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1747829342-1018757-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need for a special txqueuelen value for IPoIB.
This value represents the qdisc size which is not related to the SQ
size, and the default value provided by the stack (DEFAULT_TX_QUEUE_LEN)
is sufficient for typical use cases.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/cc97764b5a8def4ea879b371549a5867fe75c756.1728555243.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Normal set of driver updates and small fixes:
- Small improvements and fixes for erdma, efa, hfi1, bnxt_re
- Fix a UAF crash after module unload on leaking restrack entry
- Continue adding full RDMA support in mana with support for EQs, GID's
and CQs
- Improvements to the mkey cache in mlx5
- DSCP traffic class support in hns and several bug fixes
- Cap the maximum number of MADs in the receive queue to avoid OOM
- Another batch of rxe bug fixes from large scale testing
- __iowrite64_copy() optimizations for write combining MMIO memory
- Remove NULL checks before dev_put/hold()
- EFA support for receive with immediate
- Fix a recent memleaking regression in a cma error path
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCZkeo2gAKCRCFwuHvBreF
YbuNAQChzGmS4F0JAn5Wj0CDvkZghELqtvzEb92SzqcgdyQafAD/fC7f23LJ4OsO
1ZIaQEZu7j9DVg5PKFZ7WfdXjGTKqwA=
=QRXg
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Aside from the usual things this has an arch update for
__iowrite64_copy() used by the RDMA drivers.
This API was intended to generate large 64 byte MemWr TLPs on PCI.
These days most processors had done this by just repeating writel() in
a loop. S390 and some new ARM64 designs require a special helper to
get this to generate.
- Small improvements and fixes for erdma, efa, hfi1, bnxt_re
- Fix a UAF crash after module unload on leaking restrack entry
- Continue adding full RDMA support in mana with support for EQs,
GID's and CQs
- Improvements to the mkey cache in mlx5
- DSCP traffic class support in hns and several bug fixes
- Cap the maximum number of MADs in the receive queue to avoid OOM
- Another batch of rxe bug fixes from large scale testing
- __iowrite64_copy() optimizations for write combining MMIO memory
- Remove NULL checks before dev_put/hold()
- EFA support for receive with immediate
- Fix a recent memleaking regression in a cma error path"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (70 commits)
RDMA/cma: Fix kmemleak in rdma_core observed during blktests nvme/rdma use siw
RDMA/IPoIB: Fix format truncation compilation errors
bnxt_re: avoid shift undefined behavior in bnxt_qplib_alloc_init_hwq
RDMA/efa: Support QP with unsolicited write w/ imm. receive
IB/hfi1: Remove generic .ndo_get_stats64
IB/hfi1: Do not use custom stat allocator
RDMA/hfi1: Use RMW accessors for changing LNKCTL2
RDMA/mana_ib: implement uapi for creation of rnic cq
RDMA/mana_ib: boundary check before installing cq callbacks
RDMA/mana_ib: introduce a helper to remove cq callbacks
RDMA/mana_ib: create and destroy RNIC cqs
RDMA/mana_ib: create EQs for RNIC CQs
RDMA/core: Remove NULL check before dev_{put, hold}
RDMA/ipoib: Remove NULL check before dev_{put, hold}
RDMA/mlx5: Remove NULL check before dev_{put, hold}
RDMA/mlx5: Track DCT, DCI and REG_UMR QPs as diver_detail resources.
RDMA/core: Add an option to display driver-specific QPs in the rdmatool
RDMA/efa: Add shutdown notifier
RDMA/mana_ib: Fix missing ret value
IB/mlx5: Use __iowrite64_copy() for write combining stores
...
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Coccinelle reports a warning
WARNING: NULL check before dev_{put, hold} functions is not needed
The reason is the call netdev_{put, hold} of dev_{put,hold} will check NULL
There is no need to check before using dev_{put, hold}
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/ZjGDFatHRMI6Eg7M@octinomon.home
Signed-off-by: Leon Romanovsky <leon@kernel.org>
We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.
This patch prepares dev_get_iflink() and nla_put_iflink()
to run either with RTNL or RCU held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we sometime run into TX timeout from IPoIB, queue seems stopped
and can't recover. Diff with Mellanox OFED show Mellanox driver
has timeout work to recover in such case.
Add TX timeout work/NAPI work to recover such case.
Also increase the watchdog_timeo to 10 seconds, so more tolerant to
error.
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20231121130316.126364-3-jinpu.wang@ionos.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The call netdev_{put, hold} of dev_{put, hold} will check NULL,
so there is no need to check before using dev_{put, hold},
remove it to silence the warning:
./drivers/infiniband/core/nldev.c:375:2-9: WARNING: NULL check before dev_{put, hold} functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7047
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231024003815.89742-1-yang.lee@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Small cycle this time:
- Minor driver updates for hfi1, cxgb4, erdma, hns, irdma, mlx5, siw, mana
- inline CQE support for hns
- Have mlx5 display device error codes
- Pinned DMABUF support for irdma
- Continued rxe cleanups, particularly converting the MRs to use xarray
- Improvements to what can be cached in the mlx5 mkey cache
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCY/gPmgAKCRCFwuHvBreF
YW5IAP4xOAiTif4f87vD1twRU/ebq4VEX0r+C2NX5x5fwlCJrAEA7RLV8uG9Uii2
ez0BuWNxfajuvFHntnZ1E+7UDP0S8gk=
=CgUH
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Quite a small cycle this time, even with the rc8. I suppose everyone
went to sleep over xmas.
- Minor driver updates for hfi1, cxgb4, erdma, hns, irdma, mlx5, siw,
mana
- inline CQE support for hns
- Have mlx5 display device error codes
- Pinned DMABUF support for irdma
- Continued rxe cleanups, particularly converting the MRs to use
xarray
- Improvements to what can be cached in the mlx5 mkey cache"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (61 commits)
IB/mlx5: Extend debug control for CC parameters
IB/hfi1: Fix sdma.h tx->num_descs off-by-one errors
IB/hfi1: Fix math bugs in hfi1_can_pin_pages()
RDMA/irdma: Add support for dmabuf pin memory regions
RDMA/mlx5: Use query_special_contexts for mkeys
net/mlx5e: Use query_special_contexts for mkeys
net/mlx5: Change define name for 0x100 lkey value
net/mlx5: Expose bits for querying special mkeys
RDMA/rxe: Fix missing memory barriers in rxe_queue.h
RDMA/mana_ib: Fix a bug when the PF indicates more entries for registering memory on first packet
RDMA/rxe: Remove rxe_alloc()
RDMA/cma: Distinguish between sockaddr_in and sockaddr_in6 by size
Subject: RDMA/rxe: Handle zero length rdma
iw_cxgb4: Fix potential NULL dereference in c4iw_fill_res_cm_id_entry()
RDMA/mlx5: Use rdma_umem_for_each_dma_block()
RDMA/umem: Remove unused 'work' member from struct ib_umem
RDMA/irdma: Cap MSIX used to online CPUs + 1
RDMA/mlx5: Check reg_create() create for errors
RDMA/restrack: Correct spelling
RDMA/cxgb4: Fix potential null-ptr-deref in pass_establish()
...
Refactors based on comments [1] of the multiple path records support
patchset:
- Return failure if not able to set inbound/outbound PRs;
- Simplify the flow when receiving the PRs from netlink channel: When
a good PR response is received, unpack it and call the path_query
callback directly. This saves two memory allocations;
- Define RDMA_PRIMARY_PATH_MAX_REC_NUM in a proper place.
[1] https://lore.kernel.org/linux-rdma/Yyxp9E9pJtUids2o@nvidia.com/
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org> #srp
Link: https://lore.kernel.org/r/7610025d57342b8b6da0f19516c9612f9c3fdc37.1672819376.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Support receiving inbound and outbound IB path records (along with GMP
PathRecord) from user-space service through the RDMA netlink channel.
The LIDs in these 3 PRs can be used in this way:
1. GMP PR: used as the standard local/remote LIDs;
2. DLID of outbound PR: Used as the "dlid" field for outbound traffic;
3. DLID of inbound PR: Used as the "dlid" field for outbound traffic in
responder side.
This is aimed to support adaptive routing. With current IB routing
solution when a packet goes out it's assigned with a fixed DLID per
target, meaning a fixed router will be used.
The LIDs in inbound/outbound path records can be used to identify group
of routers that allow communication with another subnet's entity. With
them packets from an inter-subnet connection may travel through any
router in the set to reach the target.
As confirmed with Jason, when sending a netlink request, kernel uses
LS_RESOLVE_PATH_USE_ALL so that the service knows kernel supports
multiple PRs.
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/2fa2b6c93c4c16c8915bac3cfc4f27be1d60519d.1662631201.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
We want to remove the weight argument from the basic
netif_napi_add() API and just default to 64.
Switch ipoib to the new API for explicitly specifying
the weight.
Link: https://lore.kernel.org/r/20220705230208.924408-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Split out flags from ib_device::device_cap_flags that are only used
internally to the kernel into kernel_cap_flags that is not part of the
uapi. This limits the device_cap_flags to being the same bitmap that will
be copied to userspace.
This cleanly splits out the uverbs flags from the kernel flags to avoid
confusion in the flags bitmap.
Add some short comments describing which each of the kernel flags is
connected to. Remove unused kernel flags.
Link: https://lore.kernel.org/r/0-v2-22c19e565eef+139a-kern_caps_jgg@nvidia.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Commit 406f42fa0d ("net-next: When a bond have a massive amount of
VLANs...") introduced a rbtree for faster Ethernet address look up. To
maintain netdev->dev_addr in this tree we need to make all the writes to
it got through appropriate helpers.
Link: https://lore.kernel.org/r/20211019182604.1441387-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Link: https://lore.kernel.org/r/ca7bac6e6c9c5cc8d04eec3944edb13de0e381a3.1633874776.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compilation with W=1 produces warnings similar to the below.
drivers/infiniband/ulp/ipoib/ipoib_main.c:320: warning: This comment
starts with '/**', but isn't a kernel-doc comment. Refer
Documentation/doc-guide/kernel-doc.rst
All such occurrences were found with the following one line
git grep -A 1 "\/\*\*" drivers/infiniband/
Link: https://lore.kernel.org/r/e57d5f4ddd08b7a19934635b44d6d632841b9ba7.1623823612.git.leonro@nvidia.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com> #rtrs
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use DEVICE_ATTR_*() helper instead of plain DEVICE_ATTR, which makes the
code a bit shorter and easier to read.
Link: https://lore.kernel.org/r/20210526132753.3092-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When "enhanced IPoIB" is enabled for CX-5 devices it requires the parent
device to be UP, otherwise the child devices won't work.
Thus add a debug message to give admin a hint when only the child
interface is UP but parent interface is not.
Link: https://lore.kernel.org/r/20210408093215.24023-1-jinpu.wang@ionos.com
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The current rdma_netdev handling in ipoib hooks the tx_timeout handler,
but prints out a totally useless message that prevents effective debugging
especially when multiple transmit queues are being used.
Add a tx_timeout rdma_netdev hook and implement the callback in the hfi1
to print additional information.
The existing non-helpful message is avoided when the driver has presented
a callback.
Link: https://lore.kernel.org/r/1617026056-50483-3-git-send-email-dennis.dalessandro@cornelisnetworks.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Current code uses many different types when dealing with a port of a RDMA
device: u8, unsigned int and u32. Switch to u32 to clean up the logic.
This allows us to make (at least) the core view consistent and use the
same type. Unfortunately not all places can be converted. Many uverbs
functions expect port to be u8 so keep those places in order not to break
UAPIs. HW/Spec defined values must also not be changed.
With the switch to u32 we now can support devices with more than 255
ports. U32_MAX is reserved to make control logic a bit easier to deal
with. As a device with U32_MAX ports probably isn't going to happen any
time soon this seems like a non issue.
When a device with more than 255 ports is created uverbs will report the
RDMA device as having 255 ports as this is the max currently supported.
The verbs interface is not changed yet because the IBTA spec limits the
port size in too many places to be u8 and all applications that relies in
verbs won't be able to cope with this change. At this stage, we are
extending the interfaces that are using vendor channel solely
Once the limitation is lifted mlx5 in switchdev mode will be able to have
thousands of SFs created by the device. As the only instance of an RDMA
device that reports more than 255 ports will be a representor device and
it exposes itself as a RAW Ethernet only device CM/MAD/IPoIB and other
ULPs aren't effected by this change and their sysfs/interfaces that are
exposes to userspace can remain unchanged.
While here cleanup some alignment issues and remove unneeded sanity
checks (mainly in rdmavt),
Link: https://lore.kernel.org/r/20210301070420.439400-1-leon@kernel.org
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When a system receives a REREG event from the SM, then the SM information
in the kernel is marked as invalid and a request is sent to the SM to
update the information. The SM information is invalid in that time period.
However, receiving a REREG also occurs simultaneously in user space
applications that are now trying to rejoin the multicast groups. Some of
those may be sendonly multicast groups which are then failing.
If the SM information is invalid then ib_sa_sendonly_fullmem_support()
returns false. That is wrong because it just means that we do not know yet
if the potentially new SM supports sendonly joins.
Sendonly join was introduced in 2015 and all the Subnet managers have
supported it ever since. So there is no point in checking if a subnet
manager supports it.
Should an old opensm get a request for a sendonly join then the request
will fail. The code that is removed here accomodated that situation and
fell back to a full join.
Falling back to a full join is problematic in itself. The reason to use
the sendonly join was to reduce the traffic on the Infiniband fabric
otherwise one could have just stayed with the regular join. So this patch
may cause users of very old opensms to discover that lots of traffic
needlessly crosses their IB fabrics.
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2101281845160.13303@www.lameter.com
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The typical set of driver updates across the subsystem:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma, hns,
usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where MRA
wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail at
the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist
-----BEGIN PGP SIGNATURE-----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=LKpl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A usual cycle for RDMA with a typical mix of driver and core subsystem
updates:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma,
hns, usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where
MRA wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail
at the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using
it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (191 commits)
RDMA/ucma: Fix use after free in destroy id flow
RDMA/rxe: Handle skb_clone() failure in rxe_recv.c
RDMA/rxe: Move the definitions for rxe_av.network_type to uAPI
RDMA: Explicitly pass in the dma_device to ib_register_device
lib/scatterlist: Do not limit max_segment to PAGE_ALIGNED values
IB/mlx4: Convert rej_tmout radix-tree to XArray
RDMA/rxe: Fix bug rejecting all multicast packets
RDMA/rxe: Fix skb lifetime in rxe_rcv_mcast_pkt()
RDMA/rxe: Remove duplicate entries in struct rxe_mr
IB/hfi,rdmavt,qib,opa_vnic: Update MAINTAINERS
IB/rdmavt: Fix sizeof mismatch
MAINTAINERS: CISCO VIC LOW LATENCY NIC DRIVER
RDMA/bnxt_re: Fix sizeof mismatch for allocation of pbl_tbl.
RDMA/bnxt_re: Use rdma_umem_for_each_dma_block()
RDMA/umem: Move to allocate SG table from pages
lib/scatterlist: Add support in dynamic allocation of SG table from pages
tools/testing/scatterlist: Show errors in human readable form
tools/testing/scatterlist: Rejuvenate bit-rotten test
RDMA/ipoib: Set rtnl_link_ops for ipoib interfaces
RDMA/uverbs: Expose the new GID query API to user space
...
Report the "ipoib pkey", "mode" and "umcast" netlink attributes for every
IPoiB interface type, not just children created with 'ip link add'.
After setting the rtnl_link_ops for the parent interface, implement the
dellink() callback to block users from trying to remove it.
Fixes: 862096a8bb ("IB/ipoib: Add more rtnl_link_ops callbacks")
Link: https://lore.kernel.org/r/20201004132948.26669-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Functions related to nested interface infrastructure such as
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
In the following patch, a new member variable will be added into this
struct to fix the lockdep issue.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Guralnik says:
====================
This series handles IPoIB child interface creation with setting
interface's HW address.
In current implementation, lladdr requested by user is ignored and
overwritten. Child interface gets the same GID as the parent interface and
a QP number which is assigned by the underlying drivers.
In this series we fix this behavior so that user's requested address is
assigned to the newly created interface.
As specific QP number request is not supported for all vendors, QP number
requested by user will still be overwritten when this is not supported.
Behavior of creation of child interfaces through the sysfs mechanism or
without specifying a requested address, stays the same.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
due to dependencies.
* branch 'mlx5_ipoib_qpn':
RDMA/ipoib: Handle user-supplied address when creating child
net/mlx5: Enable QP number request when creating IPoIB underlay QP
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use the address supplied by user when creating a child interface.
Previously, the address requested by the user was ignored and overridden
with parent's GID and the random QP number assigned to the child.
Link: https://lore.kernel.org/r/20200623110105.1225750-3-leon@kernel.org
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
ipoib_mcast_carrier_on_task() insanely open codes a rtnl_lock() such that
the only time flush_workqueue() can be called is if it also clears
IPOIB_FLAG_OPER_UP.
Thus the flush inside ipoib_flush_ah() will deadlock if it gets unlucky
enough, and lockdep doesn't help us to find it early:
CPU0 CPU1 CPU2
__ipoib_ib_dev_flush()
down_read(vlan_rwsem)
ipoib_vlan_add()
rtnl_trylock()
down_write(vlan_rwsem)
ipoib_mcast_carrier_on_task()
while (!rtnl_trylock())
msleep(20);
ipoib_flush_ah()
flush_workqueue(priv->wq)
Clean up the ah_reaper related functions and lifecycle to make sense:
- Start/Stop of the reaper should only be done in open/stop NDOs, not in
any other places
- cancel and flush of the reaper should only happen in the stop NDO.
cancel is only functional when combined with IPOIB_STOP_REAPER.
- Non-stop places were flushing the AH's just need to flush out dead AH's
synchronously and ignore the background task completely. It is fully
locked and harmless to leave running.
Which ultimately fixes the ABBA deadlock by removing the unnecessary
flush_workqueue() from the problematic place under the vlan_rwsem.
Fixes: efc82eeeae ("IB/ipoib: No longer use flush as a parameter")
Link: https://lore.kernel.org/r/20200625174219.290842-1-kamalheib1@gmail.com
Reported-by: Kamal Heib <kheib@redhat.com>
Tested-by: Kamal Heib <kheib@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
A few large, long discussed works this time. The RNBD block driver has
been posted for nearly two years now, and the removal of FMR has been a
recurring discussion theme for a long time. The usual smattering of
features and bug fixes.
- Various small driver bugs fixes in rxe, mlx5, hfi1, and efa
- Continuing driver cleanups in bnxt_re, hns
- Big cleanup of mlx5 QP creation flows
- More consistent use of src port and flow label when LAG is used and a
mlx5 implementation
- Additional set of cleanups for IB CM
- 'RNBD' network block driver and target. This is a network block RDMA
device specific to ionos's cloud environment. It brings strong multipath
and resiliency capabilities.
- Accelerated IPoIB for HFI1
- QP/WQ/SRQ ioctl migration for uverbs, and support for multiple async fds
- Support for exchanging the new IBTA defiend ECE data during RDMA CM
exchanges
- Removal of the very old and insecure FMR interface from all ULPs and
drivers. FRWR should be preferred for at least a decade now.
-----BEGIN PGP SIGNATURE-----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=9zTe
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A more active cycle than most of the recent past, with a few large,
long discussed works this time.
The RNBD block driver has been posted for nearly two years now, and
flowing through RDMA due to it also introducing a new ULP.
The removal of FMR has been a recurring discussion theme for a long
time.
And the usual smattering of features and bug fixes.
Summary:
- Various small driver bugs fixes in rxe, mlx5, hfi1, and efa
- Continuing driver cleanups in bnxt_re, hns
- Big cleanup of mlx5 QP creation flows
- More consistent use of src port and flow label when LAG is used and
a mlx5 implementation
- Additional set of cleanups for IB CM
- 'RNBD' network block driver and target. This is a network block
RDMA device specific to ionos's cloud environment. It brings strong
multipath and resiliency capabilities.
- Accelerated IPoIB for HFI1
- QP/WQ/SRQ ioctl migration for uverbs, and support for multiple
async fds
- Support for exchanging the new IBTA defiend ECE data during RDMA CM
exchanges
- Removal of the very old and insecure FMR interface from all ULPs
and drivers. FRWR should be preferred for at least a decade now"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (247 commits)
RDMA/cm: Spurious WARNING triggered in cm_destroy_id()
RDMA/mlx5: Return ECE DC support
RDMA/mlx5: Don't rely on FW to set zeros in ECE response
RDMA/mlx5: Return an error if copy_to_user fails
IB/hfi1: Use free_netdev() in hfi1_netdev_free()
RDMA/hns: Uninitialized variable in modify_qp_init_to_rtr()
RDMA/core: Move and rename trace_cm_id_create()
IB/hfi1: Fix hfi1_netdev_rx_init() error handling
RDMA: Remove 'max_map_per_fmr'
RDMA: Remove 'max_fmr'
RDMA/core: Remove FMR device ops
RDMA/rdmavt: Remove FMR memory registration
RDMA/mthca: Remove FMR support for memory registration
RDMA/mlx4: Remove FMR support for memory registration
RDMA/i40iw: Remove FMR leftovers
RDMA/bnxt_re: Remove FMR leftovers
RDMA/mlx5: Remove FMR leftovers
RDMA/core: Remove FMR pool API
RDMA/rds: Remove FMR support for memory registration
RDMA/srp: Remove support for FMR memory registration
...
When connected mode is set, and we have connected and datagram traffic in
parallel, ipoib might crash with double free of datagram skb.
The current mechanism assumes that the order in the completion queue is
the same as the order of sent packets for all QPs. Order is kept only for
specific QP, in case of mixed UD and CM traffic we have few QPs (one UD and
few CM's) in parallel.
The problem:
----------------------------------------------------------
Transmit queue:
-----------------
UD skb pointer kept in queue itself, CM skb kept in spearate queue and
uses transmit queue as a placeholder to count the number of total
transmitted packets.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 .........127
------------------------------------------------------------
NL ud1 UD2 CM1 ud3 cm2 cm3 ud4 cm4 ud5 NL NL NL ...........
------------------------------------------------------------
^ ^
tail head
Completion queue (problematic scenario) - the order not the same as in
the transmit queue:
1 2 3 4 5 6 7 8 9
------------------------------------
ud1 CM1 UD2 ud3 cm2 cm3 ud4 cm4 ud5
------------------------------------
1. CM1 'wc' processing
- skb freed in cm separate ring.
- tx_tail of transmit queue increased although UD2 is not freed.
Now driver assumes UD2 index is already freed and it could be used for
new transmitted skb.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 .........127
------------------------------------------------------------
NL NL UD2 CM1 ud3 cm2 cm3 ud4 cm4 ud5 NL NL NL ...........
------------------------------------------------------------
^ ^ ^
(Bad)tail head
(Bad - Could be used for new SKB)
In this case (due to heavy load) UD2 skb pointer could be replaced by new
transmitted packet UD_NEW, as the driver assumes its free. At this point
we will have to process two 'wc' with same index but we have only one
pointer to free.
During second attempt to free the same skb we will have NULL pointer
exception.
2. UD2 'wc' processing
- skb freed according the index we got from 'wc', but it was already
overwritten by mistake. So actually the skb that was released is the
skb of the new transmitted packet and not the original one.
3. UD_NEW 'wc' processing
- attempt to free already freed skb. NUll pointer exception.
The fix:
-----------------------------------------------------------------------
The fix is to stop using the UD ring as a placeholder for CM packets, the
cyclic ring variables tx_head and tx_tail will manage the UD tx_ring, a
new cyclic variables global_tx_head and global_tx_tail are introduced for
managing and counting the overall outstanding sent packets, then the send
queue will be stopped and waken based on these variables only.
Note that no locking is needed since global_tx_head is updated in the xmit
flow and global_tx_tail is updated in the NAPI flow only. A previous
attempt tried to use one variable to count the outstanding sent packets,
but it did not work since xmit and NAPI flows can run at the same time and
the counter will be updated wrongly. Thus, we use the same simple cyclic
head and tail scheme that we have today for the UD tx_ring.
Fixes: 2c104ea683 ("IB/ipoib: Get rid of the tx_outstanding variable in all modes")
Link: https://lore.kernel.org/r/20200527134705.480068-1-leon@kernel.org
Signed-off-by: Valentine Fatiev <valentinef@mellanox.com>
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This is the prerequisite modification to the ipoib ulp to allow a
rdma netdev to obtain the default ndo ops for init/uninit/open/close.
This is accomplished by setting the netdev ops field within the
callback function passed to the netdev allocation routine which
in turn was passed into the rdma netdev allocation routine.
This allows the rdma netdev to call back into the ulp to create the
resources required for connected mode operation.
Additionally as the ulp is not re-entrant, when switching modes,
the number of real tx queues is set to 1 for the connected mode.
For datagram mode the number of real tx queues is set to the
actual number of tx queues specified at the netdev's allocation.
For the internal ulp netdev the number of tx queues defaults to 1.
It is up to the rdma netdev to specify the actual number it can support.
When the driver does not support a rdma netdev for acceleration,
(-ENOTSUPPORTED return code or the verbs function for allocation is
NULL) the ipoib ulp functions are unaffected by using the internal
netdev allocated by the ipoib ulp.
Link: https://lore.kernel.org/r/20200511160706.173205.19086.stgit@awfm-01.aw.intel.com
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Gary Leshner <Gary.S.Leshner@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When in connected mode ipoib sent broadcast pings which exceeded the mtu
size for broadcast addresses.
Add an mtu attribute to the rdma_netdev structure which ipoib sets to its
mcast mtu size.
The RDMA netdev uses this value to determine if the skb length is too long
for the mtu specified and if it is, drops the packet and logs an error
about the errant packet.
Link: https://lore.kernel.org/r/20200511160655.173205.14546.stgit@awfm-01.aw.intel.com
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Gary Leshner <Gary.S.Leshner@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently the ipoib UD mtu is restricted to 4K bytes. Remove this
limitation so that the IPOIB module can potentially use an MTU (in UD
mode) that is bounded by the MTU of the underlying device. A field is
added to the ib_port_attr structure to indicate the maximum physical
MTU the underlying device supports.
Link: https://lore.kernel.org/r/20200511160618.173205.23053.stgit@awfm-01.aw.intel.com
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sadanand Warrier <sadanand.warrier@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When a client is added it isn't allowed to fail, but all the client's have
various failure paths within their add routines.
This creates the very fringe condition where the client was added, failed
during add and didn't set the client_data. The core code will then still
call other client_data centric ops like remove(), rename(), get_nl_info(),
and get_net_dev_by_params() with NULL client_data - which is confusing and
unexpected.
If the add() callback fails, then do not call any more client ops for the
device, even remove.
Remove all the now redundant checks for NULL client_data in ops callbacks.
Update all the add() callbacks to return error codes
appropriately. EOPNOTSUPP is used for cases where the ULP does not support
the ib_device - eg because it only works with IB.
Link: https://lore.kernel.org/r/20200421172440.387069-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
There is no need to set driver version in in-tree kernel code.
Link: https://lore.kernel.org/r/20200220071239.231800-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add ndo operation to the network driver that enables configuring
ipoib_get_vf_guid operation. The operation allows to get a VF port
and node GUIDs.
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
A smaller cycle this time. Notably we see another new driver, 'Soft
iWarp', and the deletion of an ancient unused driver for nes.
- Revise and simplify the signature offload RDMA MR APIs
- More progress on hoisting object allocation boiler plate code out of the
drivers
- Driver bug fixes and revisions for hns, hfi1, efa, cxgb4, qib, i40iw
- Tree wide cleanups: struct_size, put_user_page, xarray, rst doc conversion
- Removal of obsolete ib_ucm chardev and nes driver
- netlink based discovery of chardevs and autoloading of the modules
providing them
- Move more of the rdamvt/hfi1 uapi to include/uapi/rdma
- New driver 'siw' for software based iWarp running on top of netdev,
much like rxe's software RoCE.
- mlx5 feature to report events in their raw devx format to userspace
- Expose per-object counters through rdma tool
- Adaptive interrupt moderation for RDMA (DIM), sharing the DIM core
from netdev
-----BEGIN PGP SIGNATURE-----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=iWcG
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A smaller cycle this time. Notably we see another new driver, 'Soft
iWarp', and the deletion of an ancient unused driver for nes.
- Revise and simplify the signature offload RDMA MR APIs
- More progress on hoisting object allocation boiler plate code out
of the drivers
- Driver bug fixes and revisions for hns, hfi1, efa, cxgb4, qib,
i40iw
- Tree wide cleanups: struct_size, put_user_page, xarray, rst doc
conversion
- Removal of obsolete ib_ucm chardev and nes driver
- netlink based discovery of chardevs and autoloading of the modules
providing them
- Move more of the rdamvt/hfi1 uapi to include/uapi/rdma
- New driver 'siw' for software based iWarp running on top of netdev,
much like rxe's software RoCE.
- mlx5 feature to report events in their raw devx format to userspace
- Expose per-object counters through rdma tool
- Adaptive interrupt moderation for RDMA (DIM), sharing the DIM core
from netdev"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (194 commits)
RMDA/siw: Require a 64 bit arch
RDMA/siw: Mark expected switch fall-throughs
RDMA/core: Fix -Wunused-const-variable warnings
rdma/siw: Remove set but not used variable 's'
rdma/siw: Add missing dependencies on LIBCRC32C and DMA_VIRT_OPS
RDMA/siw: Add missing rtnl_lock around access to ifa
rdma/siw: Use proper enumerated type in map_cqe_status
RDMA/siw: Remove unnecessary kthread create/destroy printouts
IB/rdmavt: Fix variable shadowing issue in rvt_create_cq
RDMA/core: Fix race when resolving IP address
RDMA/core: Make rdma_counter.h compile stand alone
IB/core: Work on the caller socket net namespace in nldev_newlink()
RDMA/rxe: Fill in wc byte_len with IB_WC_RECV_RDMA_WITH_IMM
RDMA/mlx5: Set RDMA DIM to be enabled by default
RDMA/nldev: Added configuration of RDMA dynamic interrupt moderation to netlink
RDMA/core: Provide RDMA DIM support for ULPs
linux/dim: Implement RDMA adaptive moderation (DIM)
IB/mlx5: Report correctly tag matching rendezvous capability
docs: infiniband: add it to the driver-api bookset
IB/mlx5: Implement VHCA tunnel mechanism in DEVX
...
Despite failure in ipoib_dev_init() we continue with initialization flow
and creation of child device. It causes to the situation where this child
device is added too early to parent device list.
Change the logic, so in case of failure we properly return error from
ipoib_dev_init() and add child only in success path.
Fixes: eaeb398425 ("IB/ipoib: Move init code to ndo_init")
Signed-off-by: Valentine Fatiev <valentinef@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
in the case of IPoIB with SRIOV enabled hardware
ip link show command incorrecly prints
0 instead of a VF hardware address.
Before:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state disable,
trust off, query_rss off
...
After:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
vf 0 link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff, spoof
checking off, link-state disable, trust off, query_rss off
v1->v2: just copy an address without modifing ifla_vf_mac
v2->v3: update the changelog
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Systemd triggers the following warning during IPoIB device load:
mlx5_core 0000:00:0c.0 ib0: "systemd-udevd" wants to know my dev_id.
Should it look at dev_port instead?
See Documentation/ABI/testing/sysfs-class-net for more info.
This is caused due to user space attempt to differentiate old systems
without dev_port and new systems with dev_port. In case dev_port will be
zero, the systemd will try to read dev_id instead.
There is no need to print a warning in such case, because it is valid
situation and it is needed to ensure systemd compatibility with old
kernels.
Link: https://github.com/systemd/systemd/blob/master/src/udev/udev-builtin-net_id.c#L358
Cc: <stable@vger.kernel.org> # 4.19
Fixes: f6350da41d ("IB/ipoib: Log sysfs 'dev_id' accesses from userspace")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
We have many loops iterating over all of the end port numbers on a struct
ib_device, simplify them with a for_each helper.
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Changed debug statements to use %s and __func__ instead
of hard-coded function's name.
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
