This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com> # ROHM BM1390
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-20-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use `\t(\{ ?\},|\{\}|\{\s*/\*.*\*/\s*\},?)$` regex to find and replace
the array sentinel in all IIO drivers to the same style.
For some time, we've been trying to consistently use `{ }` (no trailing
comma, no comment, one space between braces) for array sentinels in the
IIO subsystem. Still nearly 50% of existing code uses a different style.
To save reviewers from having to request this trivial change as
frequently, let's normalize the style in all existing IIO drivers.
At least when code is copy/pasted to new drivers, the style will be
consistent.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250411-iio-sentinel-normalization-v1-1-d293de3e3d93@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/20250331121317.1694135-30-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Acked-By: Matti Vaittinen <mazziesaccount@gmail.com> #for the BD1390
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-7-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The BM1390 uses mutex for protecting the fifo read sequence. The clean-up
for a few of the functions can be slightly simplified by removing the
goto-based error handling/unlocking and by utilizing the guard(mutex)
scoped mutex handling instead.
Simplify driver by using the scoped mutexes.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/a4c2f21189964132d245531b77fb0865562443a1.1732193263.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a check on non-zero ret that is redundant because the
same check is being performed in a previous if statement and
also before that. The check is not required, remove it.
Signed-off-by: Colin Ian King <colin.i.king@intel.com>
Link: https://patch.msgid.link/20241010170835.772764-1-colin.i.king@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support for the ROHM BM1390 pressure sensor. The BM1390GLV-Z can measure
pressures ranging from 300 hPa to 1300 hPa with configurable measurement
averaging and internal FIFO. The sensor does also provide temperature
measurements.
Sensor does also contain IIR filter implemented in HW. The data-sheet
says the IIR filter can be configured to be "weak", "middle" or
"strong". Some RMS noise figures are provided in data sheet but no
accurate maths for the filter configurations is provided. Hence, the IIR
filter configuration is not supported by this driver and the filter is
configured to the "middle" setting (at least not for now).
The FIFO measurement mode is only measuring the pressure and not the
temperature. The driver measures temperature when FIFO is flushed and
simply uses the same measured temperature value to all reported
temperatures. This should not be a problem when temperature is not
changing very rapidly (several degrees C / second) but allows users to
get the temperature measurements from sensor without any additional logic.
This driver allows the sensor to be used in two muitually exclusive ways,
1. With trigger (data-ready IRQ).
In this case the FIFO is not used as we get data ready for each collected
sample. Instead, for each data-ready IRQ we read the sample from sensor
and push it to the IIO buffer.
2. With hardware FIFO and watermark IRQ.
In this case the data-ready is not used but we enable watermark IRQ. At
each watermark IRQ we go and read all samples in FIFO and push them to the
IIO buffer.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/4f23211e3cf248f9f48ddb2a752387bb00e9c2c4.1695727471.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
