The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: chuguangqing <chuguangqing@inspur.com>
Link: https://patch.msgid.link/20250611085838.4761-4-chuguangqing@inspur.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79702 is similar to the BD79703, except that it has only 4
channels whereas BD79703 has 6 channels. The channel 'addresses' of the
first two channels (used to identify the channel when data is read over
SPI) are same for both ICs. The next two channels of the BD79702 have
same addresses as the last two channels of the BD79703. This means the
BD79702 channel addresses do not follow the channel numbers with a
constant offset. Thus, we need to specify the addresses separately,
instead of directly deriving them from the channel number with a
constant offset.
It's worth noting that the data-sheet describes the BD79702 as a device
having channels 1,2,5 and 6. The driver however represents channels
0,1,2,3 to the users - with no gaps in the numbering - which may be more
familiar view for the application software.
Support ROHM BD79702 DAC.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/0ba243a63115dd4af03ebf9656c65b8c259a3e34.1743576022.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The BD79700 and BD79701 look like almost exact subsets of the BD79703.
The BD79703 contains 6 channels (channels 0 to 5). The BD79700 provides
only 2 channels, matching the BD79703 channels 0 and 1. The BD79701
provides 3 channels (matching BD79703 channels 0, 1, and 2).
Furthermore, the BD79700 and BD79701 do not have separate VFS pin but
use VCC for the full-scale voltage.
Suopport these ICs using the BD79703 driver.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/845aa45974f6fb81c83046368a24a0674e9a8b0e.1743576022.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79703 needs to identify a channel which we are reading from
in the SPI transfers. This can be seen as an address for the device.
For the bd79703 the address is nicely aligned with the channel number,
so the driver uses the channel ID for the SPI transfers. This, however,
does not need to be the case. The iio_chan_spec has a separate 'address'
field, which we can populate directly with this information.
This helps adding new ICs like the ROHM BD79702 where the channel ID is
different from this address to be handled by this driver, so we don't
need to have separate, IC specific mapping for channel numbers <=>
addresses.
Make the 'address' field in the iio_chan_spec to contain the SPI protocol
address for the channel, and use this value in the transfers.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/e53cb4120d16a3c678e1f391b600af630d6767ce.1743576022.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79703 is a 6 channel digital to analog converter.
Based on the data-sheet examples the hardware would support setting the
DAC word without changing the actual output. The data-sheet is not too
specific on how the enabling the output of new voltage set by DAC
should be done - hence this is not implemented by the driver.
The BD79703 would also support two specific "PULL_DOWN" modes. These
aren't currently supported by the driver either.
Add a very basic support for controlling the channel outputs one-by-one.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/bc77d7b979ca28408a216f597082fcd94ec63be7.1734608215.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
